- Alsa-devel - mailman.alsa-project.org

[PATCH] ASoC: dt-bindings: nau8825: Convert to dtschema
by David Lin 10 May '23

10 May '23

Convert the NAU8825 audio CODEC bindings to DT schema. Signed-off-by: David Lin <CTLIN0(a)nuvoton.com> --- .../devicetree/bindings/sound/nau8825.txt | 111 -------- .../bindings/sound/nuvoton,nau8825.yaml | 242 ++++++++++++++++++ 2 files changed, 242 insertions(+), 111 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sound/nau8825.txt create mode 100644 Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml diff --git a/Documentation/devicetree/bindings/sound/nau8825.txt b/Documentation/devicetree/bindings/sound/nau8825.txt deleted file mode 100644 index a9c34526f4cb..000000000000 --- a/Documentation/devicetree/bindings/sound/nau8825.txt +++ /dev/null @@ -1,111 +0,0 @@ -Nuvoton NAU8825 audio codec - -This device supports I2C only. - -Required properties: - - compatible : Must be "nuvoton,nau8825" - - - reg : the I2C address of the device. This is either 0x1a (CSB=0) or 0x1b (CSB=1). - -Optional properties: - - nuvoton,jkdet-enable: Enable jack detection via JKDET pin. - - nuvoton,jkdet-pull-enable: Enable JKDET pin pull. If set - pin pull enabled, - otherwise pin in high impedance state. - - nuvoton,jkdet-pull-up: Pull-up JKDET pin. If set then JKDET pin is pull up, otherwise pull down. - - nuvoton,jkdet-polarity: JKDET pin polarity. 0 - active high, 1 - active low. - - - nuvoton,vref-impedance: VREF Impedance selection - 0 - Open - 1 - 25 kOhm - 2 - 125 kOhm - 3 - 2.5 kOhm - - - nuvoton,micbias-voltage: Micbias voltage level. - 0 - VDDA - 1 - VDDA - 2 - VDDA * 1.1 - 3 - VDDA * 1.2 - 4 - VDDA * 1.3 - 5 - VDDA * 1.4 - 6 - VDDA * 1.53 - 7 - VDDA * 1.53 - - - nuvoton,sar-threshold-num: Number of buttons supported - - nuvoton,sar-threshold: Impedance threshold for each button. Array that contains up to 8 buttons configuration. SAR value is calculated as - SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R) - where MICBIAS is configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by 'nuvoton,sar-voltage', R - button impedance. - Refer datasheet section 10.2 for more information about threshold calculation. - - - nuvoton,sar-hysteresis: Button impedance measurement hysteresis. - - - nuvoton,sar-voltage: Reference voltage for button impedance measurement. - 0 - VDDA - 1 - VDDA - 2 - VDDA * 1.1 - 3 - VDDA * 1.2 - 4 - VDDA * 1.3 - 5 - VDDA * 1.4 - 6 - VDDA * 1.53 - 7 - VDDA * 1.53 - - - nuvoton,sar-compare-time: SAR compare time - 0 - 500 ns - 1 - 1 us - 2 - 2 us - 3 - 4 us - - - nuvoton,sar-sampling-time: SAR sampling time - 0 - 2 us - 1 - 4 us - 2 - 8 us - 3 - 16 us - - - nuvoton,short-key-debounce: Button short key press debounce time. - 0 - 30 ms - 1 - 50 ms - 2 - 100 ms - 3 - 30 ms - - - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms - - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms - - - nuvoton,crosstalk-enable: make crosstalk function enable if set. - - - nuvoton,adcout-drive-strong: make the drive strength of ADCOUT IO PIN strong if set. - Otherwise, the drive keeps normal strength. - - - nuvoton,adc-delay-ms: Delay (in ms) to make input path stable and avoid pop noise. The - default value is 125 and range between 125 to 500 ms. - - - clocks: list of phandle and clock specifier pairs according to common clock bindings for the - clocks described in clock-names - - clock-names: should include "mclk" for the MCLK master clock - -Example: - - headset: nau8825@1a { - compatible = "nuvoton,nau8825"; - reg = <0x1a>; - interrupt-parent = <&gpio>; - interrupts = <TEGRA_GPIO(E, 6) IRQ_TYPE_LEVEL_LOW>; - nuvoton,jkdet-enable; - nuvoton,jkdet-pull-enable; - nuvoton,jkdet-pull-up; - nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>; - nuvoton,vref-impedance = <2>; - nuvoton,micbias-voltage = <6>; - // Setup 4 buttons impedance according to Android specification - nuvoton,sar-threshold-num = <4>; - nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>; - nuvoton,sar-hysteresis = <1>; - nuvoton,sar-voltage = <0>; - nuvoton,sar-compare-time = <0>; - nuvoton,sar-sampling-time = <0>; - nuvoton,short-key-debounce = <2>; - nuvoton,jack-insert-debounce = <7>; - nuvoton,jack-eject-debounce = <7>; - nuvoton,crosstalk-enable; - - clock-names = "mclk"; - clocks = <&tegra_pmc TEGRA_PMC_CLK_OUT_2>; - }; diff --git a/Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml b/Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml new file mode 100644 index 000000000000..ab352422d48e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml @@ -0,0 +1,242 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/nuvoton,nau8825.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NAU8825 audio CODEC + +maintainers: + - John Hsu <KCHSU0(a)nuvoton.com> + +allOf: + - $ref: dai-common.yaml# + +properties: + compatible: + enum: + - nuvoton,nau8825 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + description: + The CODEC's interrupt output. + + nuvoton,jkdet-enable: + description: + Enable jack detection via JKDET pin. + type: boolean + + nuvoton,jkdet-pull-enable: + description: + Enable JKDET pin pull. + If set - pin pull enabled, otherwise pin in high impedance state. + type: boolean + + nuvoton,jkdet-pull-up: + description: + Pull-up JKDET pin. + If set then JKDET pin is pull up, otherwise pull down. + type: boolean + + nuvoton,jkdet-polarity: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + JKDET pin polarity. + enum: + - 0 # active high + - 1 # active low + default: 1 + + nuvoton,vref-impedance: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + VREF Impedance selection. + enum: + - 0 # Open + - 1 # 25 kOhm + - 2 # 125 kOhm + - 3 # 2.5 kOhm + default: 2 + + nuvoton,micbias-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Micbias voltage level. + enum: + - 0 # VDDA + - 1 # VDDA + - 2 # VDDA * 1.1 + - 3 # VDDA * 1.2 + - 4 # VDDA * 1.3 + - 5 # VDDA * 1.4 + - 6 # VDDA * 1.53 + - 7 # VDDA * 1.53 + default: 6 + + nuvoton,sar-threshold-num: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Number of buttons supported. + minimum: 1 + maximum: 4 + default: 4 + + nuvoton,sar-threshold: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + Impedance threshold for each button. Array that contains up to 8 buttons + configuration. SAR value is calculated as + SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R) where MICBIAS is + configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by + 'nuvoton,sar-voltage', R - button impedance. + Refer datasheet section 10.2 for more information about threshold + calculation. + minItems: 1 + maxItems: 4 + items: + minimum: 0 + maximum: 255 + + nuvoton,sar-hysteresis: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Button impedance measurement hysteresis. + default: 0 + + nuvoton,sar-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Reference voltage for button impedance measurement. + enum: + - 0 # VDDA + - 1 # VDDA + - 2 # VDDA * 1.1 + - 3 # VDDA * 1.2 + - 4 # VDDA * 1.3 + - 5 # VDDA * 1.4 + - 6 # VDDA * 1.53 + - 7 # VDDA * 1.53 + default: 6 + + nuvoton,sar-compare-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + SAR compare time. + enum: + - 0 # 500 ns + - 1 # 1 us + - 2 # 2 us + - 3 # 4 us + default: 1 + + nuvoton,sar-sampling-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + SAR sampling time. + enum: + - 0 # 2 us + - 1 # 4 us + - 2 # 8 us + - 3 # 16 us + default: 1 + + nuvoton,short-key-debounce: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Button short key press debounce time. + enum: + - 0 # 30 ms + - 1 # 50 ms + - 2 # 100 ms + - 3 # 30 ms + default: 3 + + nuvoton,jack-insert-debounce: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + number from 0 to 7 that sets debounce time to 2^(n+2) ms. + maximum: 7 + default: 7 + + nuvoton,jack-eject-debounce: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + number from 0 to 7 that sets debounce time to 2^(n+2) ms + maximum: 7 + default: 0 + + nuvoton,crosstalk-enable: + description: + make crosstalk function enable if set. + type: boolean + + nuvoton,adcout-drive-strong: + description: + make the drive strength of ADCOUT IO PIN strong if set. + Otherwise, the drive keeps normal strength. + type: boolean + + nuvoton,adc-delay-ms: + description: + Delay (in ms) to make input path stable and avoid pop noise. + The default value is 125 and range between 125 to 500 ms. + minimum: 125 + maximum: 500 + default: 125 + + clocks: + description: + list of phandle and clock specifier pairs according to common clock + bindings for the clocks described in clock-names. + maxItems: 1 + + clock-names: + description: + should include "mclk" for the MCLK master clock. + items: + - const: mclk + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + nau8825@1a { + compatible = "nuvoton,nau8825"; + reg = <0x1a>; + interrupt-parent = <&gpio>; + interrupts = <38 IRQ_TYPE_LEVEL_LOW>; + nuvoton,jkdet-enable; + nuvoton,jkdet-pull-enable; + nuvoton,jkdet-pull-up; + nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>; + nuvoton,vref-impedance = <2>; + nuvoton,micbias-voltage = <6>; + // Setup 4 buttons impedance according to Android specification + nuvoton,sar-threshold-num = <4>; + nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>; + nuvoton,sar-hysteresis = <1>; + nuvoton,sar-voltage = <0>; + nuvoton,sar-compare-time = <0>; + nuvoton,sar-sampling-time = <0>; + nuvoton,short-key-debounce = <2>; + nuvoton,jack-insert-debounce = <7>; + nuvoton,jack-eject-debounce = <7>; + nuvoton,crosstalk-enable; + + clock-names = "mclk"; + clocks = <&tegra_pmc 1>; + }; + }; -- 2.25.1

3 4

Broadwell rt286 volume too low
by GitHub issues - opened 10 May '23

10 May '23

alsa-project/alsa-ucm-conf issue #312 was opened from benfuddled: - Distribution and distribution version: Pop!_OS 22.04 LTS (I've also experienced this issue on multiple versions of Fedora and Ubuntu. - Desktop Environment: Gnome 42 - Kernel version (uname -r): 6.2.6-76060206-generic - PipeWire version: 0.3.70 ## Description of Problem: My laptop (an HP Spectre X360 13-4002dx) speakers and headphone jack output audio at extremely low levels, to the point where initially I thought they weren't outputting audio at all. It was only when I allowed over-amplification in gnome-tweaks and holding my ear up to the speaker that I realized there was sound coming out. However, when I plug in a pair of USB headphones (not via the headphone jack) sound levels are within expected range. Same thing if I output sound via HDMI to a television. results of running alsa-info: http://alsa-project.org/db/?f=76b61d75f256f85bfcef41f7ae704fffb146cf06 Note: Myself and a few others had this problem and initially filed bugs independently with pipewire, but [a commenter](https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/2822#n… seemed to think it may be a problem with the UCM file for this device. Hoping someone here can shed some light on the issue. Thank you! Issue URL : https://github.com/alsa-project/alsa-ucm-conf/issues/312 Repository URL: https://github.com/alsa-project/alsa-ucm-conf

1 0

[PATCH] ASoC:codecs: lpass: Fix for KASAN use_after_free out of bounds
by Ravulapati Vishnu Vardhan Rao 09 May '23

09 May '23

When we run syzkaller we get below Out of Bounds error. "KASAN: slab-out-of-bounds Read in regcache_flat_read" Below is the backtrace of the issue: BUG: KASAN: slab-out-of-bounds in regcache_flat_read+0x10c/0x110 Read of size 4 at addr ffffff8088fbf714 by task syz-executor.4/14144 CPU: 6 PID: 14144 Comm: syz-executor.4 Tainted: G W Hardware name: Qualcomm Technologies, Inc. sc7280 CRD platform (rev5+) (DT) Call trace: dump_backtrace+0x0/0x4ec show_stack+0x34/0x50 dump_stack_lvl+0xdc/0x11c print_address_description+0x30/0x2d8 kasan_report+0x178/0x1e4 __asan_report_load4_noabort+0x44/0x50 regcache_flat_read+0x10c/0x110 regcache_read+0xf8/0x5a0 _regmap_read+0x45c/0x86c _regmap_update_bits+0x128/0x290 regmap_update_bits_base+0xc0/0x15c snd_soc_component_update_bits+0xa8/0x22c snd_soc_component_write_field+0x68/0xd4 tx_macro_put_dec_enum+0x1d0/0x268 snd_ctl_elem_write+0x288/0x474 By Error checking and checking valid values issue gets rectifies. Signed-off-by: Ravulapati Vishnu Vardhan Rao <quic_visr(a)quicinc.com> --- sound/soc/codecs/lpass-tx-macro.c | 19 +++++++++++++++---- 1 file changed, 15 insertions(+), 4 deletions(-) diff --git a/sound/soc/codecs/lpass-tx-macro.c b/sound/soc/codecs/lpass-tx-macro.c index da6fcf7f0991..2fc150b17f29 100644 --- a/sound/soc/codecs/lpass-tx-macro.c +++ b/sound/soc/codecs/lpass-tx-macro.c @@ -746,6 +746,8 @@ static int tx_macro_put_dec_enum(struct snd_kcontrol *kcontrol, struct tx_macro *tx = snd_soc_component_get_drvdata(component); val = ucontrol->value.enumerated.item[0]; + if (val < 0 && val > 15) + return -EINVAL; switch (e->reg) { case CDC_TX_INP_MUX_ADC_MUX0_CFG0: @@ -772,6 +774,9 @@ static int tx_macro_put_dec_enum(struct snd_kcontrol *kcontrol, case CDC_TX_INP_MUX_ADC_MUX7_CFG0: mic_sel_reg = CDC_TX7_TX_PATH_CFG0; break; + default: + dev_err(component->dev, "Error in configuration!!\n"); + return -EINVAL; } if (val != 0) { @@ -785,10 +790,16 @@ static int tx_macro_put_dec_enum(struct snd_kcontrol *kcontrol, snd_soc_component_write_field(component, mic_sel_reg, CDC_TXn_ADC_DMIC_SEL_MASK, 1); dmic = TX_ADC_TO_DMIC(val); - dmic_clk_reg = CDC_TX_TOP_CSR_SWR_DMICn_CTL(dmic); - snd_soc_component_write_field(component, dmic_clk_reg, - CDC_TX_SWR_DMIC_CLK_SEL_MASK, - tx->dmic_clk_div); + if (dmic < 4) { + dmic_clk_reg = CDC_TX_TOP_CSR_SWR_DMICn_CTL(dmic); + snd_soc_component_write_field(component, dmic_clk_reg, + CDC_TX_SWR_DMIC_CLK_SEL_MASK, + tx->dmic_clk_div); + } else { + dev_err(component->dev, "Error in dmic configuration!!\n"); + return -EINVAL; + } + } } -- 2.17.1

4 4

[PATCH v3] ASoC: rt722-sdca: Add RT722 SDCA driver
by Jack Yu 09 May '23

09 May '23

This is the initial codec driver for rt722-sdca. Signed-off-by: Jack Yu <jack.yu(a)realtek.com> --- Patch v2 : To fix warning message from kernel test robot. Patch v3 : To add information for port configuration and separate DAIs for dmic/speaker, hw_params settings are separated as well. --- sound/soc/codecs/Kconfig | 7 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/rt722-sdca-sdw.c | 510 ++++++++++ sound/soc/codecs/rt722-sdca-sdw.h | 124 +++ sound/soc/codecs/rt722-sdca.c | 1555 +++++++++++++++++++++++++++++ sound/soc/codecs/rt722-sdca.h | 238 +++++ 6 files changed, 2436 insertions(+) create mode 100644 sound/soc/codecs/rt722-sdca-sdw.c create mode 100644 sound/soc/codecs/rt722-sdca-sdw.h create mode 100644 sound/soc/codecs/rt722-sdca.c create mode 100644 sound/soc/codecs/rt722-sdca.h diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 79d2362ad055..a163e2afdf72 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -207,6 +207,7 @@ config SND_SOC_ALL_CODECS imply SND_SOC_RT712_SDCA_DMIC_SDW imply SND_SOC_RT715_SDW imply SND_SOC_RT715_SDCA_SDW + imply SND_SOC_RT722_SDCA_SDW imply SND_SOC_RT1308_SDW imply SND_SOC_RT1316_SDW imply SND_SOC_RT1318_SDW @@ -1539,6 +1540,12 @@ config SND_SOC_RT712_SDCA_DMIC_SDW select REGMAP_SOUNDWIRE select REGMAP_SOUNDWIRE_MBQ +config SND_SOC_RT722_SDCA_SDW + tristate "Realtek RT722 SDCA Codec - SDW" + depends on SOUNDWIRE + select REGMAP_SOUNDWIRE + select REGMAP_SOUNDWIRE_MBQ + config SND_SOC_RT715 tristate diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 5cdbae88e6e3..cd799306331c 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -237,6 +237,7 @@ snd-soc-rt712-sdca-objs := rt712-sdca.o rt712-sdca-sdw.o snd-soc-rt712-sdca-dmic-objs := rt712-sdca-dmic.o snd-soc-rt715-objs := rt715.o rt715-sdw.o snd-soc-rt715-sdca-objs := rt715-sdca.o rt715-sdca-sdw.o +snd-soc-rt722-sdca-objs := rt722-sdca.o rt722-sdca-sdw.o snd-soc-rt9120-objs := rt9120.o snd-soc-sdw-mockup-objs := sdw-mockup.o snd-soc-sgtl5000-objs := sgtl5000.o @@ -607,6 +608,7 @@ obj-$(CONFIG_SND_SOC_RT712_SDCA_SDW) += snd-soc-rt712-sdca.o obj-$(CONFIG_SND_SOC_RT712_SDCA_DMIC_SDW) += snd-soc-rt712-sdca-dmic.o obj-$(CONFIG_SND_SOC_RT715) += snd-soc-rt715.o obj-$(CONFIG_SND_SOC_RT715_SDCA_SDW) += snd-soc-rt715-sdca.o +obj-$(CONFIG_SND_SOC_RT722_SDCA_SDW) += snd-soc-rt722-sdca.o obj-$(CONFIG_SND_SOC_RT9120) += snd-soc-rt9120.o obj-$(CONFIG_SND_SOC_SDW_MOCKUP) += snd-soc-sdw-mockup.o obj-$(CONFIG_SND_SOC_SGTL5000) += snd-soc-sgtl5000.o diff --git a/sound/soc/codecs/rt722-sdca-sdw.c b/sound/soc/codecs/rt722-sdca-sdw.c new file mode 100644 index 000000000000..0a791a14215e --- /dev/null +++ b/sound/soc/codecs/rt722-sdca-sdw.c @@ -0,0 +1,510 @@ +// SPDX-License-Identifier: GPL-2.0-only +// +// rt722-sdca-sdw.c -- rt722 SDCA ALSA SoC audio driver +// +// Copyright(c) 2023 Realtek Semiconductor Corp. +// +// + +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/module.h> +#include <linux/mod_devicetable.h> +#include <linux/pm_runtime.h> +#include <linux/soundwire/sdw_registers.h> + +#include "rt722-sdca.h" +#include "rt722-sdca-sdw.h" + +static bool rt722_sdca_readable_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x2f01 ... 0x2f0a: + case 0x2f35 ... 0x2f36: + case 0x2f50: + case 0x2f54: + case 0x2f58 ... 0x2f5d: + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, RT722_SDCA_CTL_SELECTED_MODE, + 0): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, RT722_SDCA_CTL_DETECTED_MODE, + 0): + case SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, RT722_SDCA_CTL_HIDTX_CURRENT_OWNER, + 0) ... SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_MESSAGE_LENGTH, 0): + case RT722_BUF_ADDR_HID1 ... RT722_BUF_ADDR_HID2: + return true; + default: + return false; + } +} + +static bool rt722_sdca_volatile_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x2f01: + case 0x2f54: + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, RT722_SDCA_CTL_DETECTED_MODE, + 0): + case SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, RT722_SDCA_CTL_HIDTX_CURRENT_OWNER, + 0) ... SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_MESSAGE_LENGTH, 0): + case RT722_BUF_ADDR_HID1 ... RT722_BUF_ADDR_HID2: + return true; + default: + return false; + } +} + +static bool rt722_sdca_mbq_readable_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x2000000 ... 0x2000024: + case 0x2000029 ... 0x200004a: + case 0x2000051 ... 0x2000052: + case 0x200005a ... 0x200005b: + case 0x2000061 ... 0x2000069: + case 0x200006b: + case 0x2000070: + case 0x200007f: + case 0x2000082 ... 0x200008e: + case 0x2000090 ... 0x2000094: + case 0x5300000 ... 0x5300002: + case 0x5400002: + case 0x5600000 ... 0x5600007: + case 0x5700000 ... 0x5700004: + case 0x5800000 ... 0x5800004: + case 0x5b00003: + case 0x5c00011: + case 0x5d00006: + case 0x5f00000 ... 0x5f0000d: + case 0x5f00030: + case 0x6100000 ... 0x6100051: + case 0x6100055 ... 0x6100057: + case 0x6100062: + case 0x6100064 ... 0x6100065: + case 0x6100067: + case 0x6100070 ... 0x610007c: + case 0x6100080: + case SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_01): + case SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_02): + case SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_03): + case SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_04): + case SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_VOLUME, CH_L): + case SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_VOLUME, CH_R): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_VOLUME, + CH_L): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_VOLUME, + CH_R): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_VOLUME, + CH_L): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_VOLUME, + CH_R): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, + RT722_SDCA_CTL_FU_CH_GAIN, CH_L): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, + RT722_SDCA_CTL_FU_CH_GAIN, CH_R): + return true; + default: + return false; + } +} + +static bool rt722_sdca_mbq_volatile_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x2000000: + case 0x200000d: + case 0x2000019: + case 0x2000020: + case 0x2000030: + case 0x2000046: + case 0x2000067: + case 0x2000084: + case 0x2000086: + return true; + default: + return false; + } +} + +static const struct regmap_config rt722_sdca_regmap = { + .reg_bits = 32, + .val_bits = 8, + .readable_reg = rt722_sdca_readable_register, + .volatile_reg = rt722_sdca_volatile_register, + .max_register = 0x44ffffff, + .reg_defaults = rt722_sdca_reg_defaults, + .num_reg_defaults = ARRAY_SIZE(rt722_sdca_reg_defaults), + .cache_type = REGCACHE_RBTREE, + .use_single_read = true, + .use_single_write = true, +}; + +static const struct regmap_config rt722_sdca_mbq_regmap = { + .name = "sdw-mbq", + .reg_bits = 32, + .val_bits = 16, + .readable_reg = rt722_sdca_mbq_readable_register, + .volatile_reg = rt722_sdca_mbq_volatile_register, + .max_register = 0x41000312, + .reg_defaults = rt722_sdca_mbq_defaults, + .num_reg_defaults = ARRAY_SIZE(rt722_sdca_mbq_defaults), + .cache_type = REGCACHE_RBTREE, + .use_single_read = true, + .use_single_write = true, +}; + +static int rt722_sdca_update_status(struct sdw_slave *slave, + enum sdw_slave_status status) +{ + struct rt722_sdca_priv *rt722 = dev_get_drvdata(&slave->dev); + + /* Update the status */ + rt722->status = status; + + if (status == SDW_SLAVE_UNATTACHED) + rt722->hw_init = false; + + if (status == SDW_SLAVE_ATTACHED) { + if (rt722->hs_jack) { + /* + * Due to the SCP_SDCA_INTMASK will be cleared by any reset, and then + * if the device attached again, we will need to set the setting back. + * It could avoid losing the jack detection interrupt. + * This also could sync with the cache value as the rt722_sdca_jack_init set. + */ + sdw_write_no_pm(rt722->slave, SDW_SCP_SDCA_INTMASK1, + SDW_SCP_SDCA_INTMASK_SDCA_0 | SDW_SCP_SDCA_INTMASK_SDCA_6); + sdw_write_no_pm(rt722->slave, SDW_SCP_SDCA_INTMASK2, + SDW_SCP_SDCA_INTMASK_SDCA_8); + } + } + + /* + * Perform initialization only if slave status is present and + * hw_init flag is false + */ + if (rt722->hw_init || rt722->status != SDW_SLAVE_ATTACHED) + return 0; + + /* perform I/O transfers required for Slave initialization */ + return rt722_sdca_io_init(&slave->dev, slave); +} + +static int rt722_sdca_read_prop(struct sdw_slave *slave) +{ + struct sdw_slave_prop *prop = &slave->prop; + int nval; + int i, j; + u32 bit; + unsigned long addr; + struct sdw_dpn_prop *dpn; + + prop->scp_int1_mask = SDW_SCP_INT1_BUS_CLASH | SDW_SCP_INT1_PARITY; + prop->quirks = SDW_SLAVE_QUIRKS_INVALID_INITIAL_PARITY; + + prop->paging_support = true; + + /* + * port = 1 for headphone playback + * port = 2 for headset-mic capture + * port = 3 for speaker playback + * port = 6 for digital-mic capture + */ + prop->source_ports = BIT(6) | BIT(2); /* BITMAP: 01000100 */ + prop->sink_ports = BIT(3) | BIT(1); /* BITMAP: 00001010 */ + + nval = hweight32(prop->source_ports); + prop->src_dpn_prop = devm_kcalloc(&slave->dev, nval, + sizeof(*prop->src_dpn_prop), GFP_KERNEL); + if (!prop->src_dpn_prop) + return -ENOMEM; + + i = 0; + dpn = prop->src_dpn_prop; + addr = prop->source_ports; + for_each_set_bit(bit, &addr, 32) { + dpn[i].num = bit; + dpn[i].type = SDW_DPN_FULL; + dpn[i].simple_ch_prep_sm = true; + dpn[i].ch_prep_timeout = 10; + i++; + } + + /* do this again for sink now */ + nval = hweight32(prop->sink_ports); + prop->sink_dpn_prop = devm_kcalloc(&slave->dev, nval, + sizeof(*prop->sink_dpn_prop), GFP_KERNEL); + if (!prop->sink_dpn_prop) + return -ENOMEM; + + j = 0; + dpn = prop->sink_dpn_prop; + addr = prop->sink_ports; + for_each_set_bit(bit, &addr, 32) { + dpn[j].num = bit; + dpn[j].type = SDW_DPN_FULL; + dpn[j].simple_ch_prep_sm = true; + dpn[j].ch_prep_timeout = 10; + j++; + } + + /* set the timeout values */ + prop->clk_stop_timeout = 200; + + /* wake-up event */ + prop->wake_capable = 1; + + return 0; +} + +static int rt722_sdca_interrupt_callback(struct sdw_slave *slave, + struct sdw_slave_intr_status *status) +{ + struct rt722_sdca_priv *rt722 = dev_get_drvdata(&slave->dev); + int ret, stat; + int count = 0, retry = 3; + unsigned int sdca_cascade, scp_sdca_stat1, scp_sdca_stat2 = 0; + + if (cancel_delayed_work_sync(&rt722->jack_detect_work)) { + dev_warn(&slave->dev, "%s the pending delayed_work was cancelled", __func__); + /* avoid the HID owner doesn't change to device */ + if (rt722->scp_sdca_stat2) + scp_sdca_stat2 = rt722->scp_sdca_stat2; + } + + /* + * The critical section below intentionally protects a rather large piece of code. + * We don't want to allow the system suspend to disable an interrupt while we are + * processing it, which could be problematic given the quirky SoundWire interrupt + * scheme. We do want however to prevent new workqueues from being scheduled if + * the disable_irq flag was set during system suspend. + */ + mutex_lock(&rt722->disable_irq_lock); + + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT1); + if (ret < 0) + goto io_error; + rt722->scp_sdca_stat1 = ret; + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT2); + if (ret < 0) + goto io_error; + rt722->scp_sdca_stat2 = ret; + if (scp_sdca_stat2) + rt722->scp_sdca_stat2 |= scp_sdca_stat2; + do { + /* clear flag */ + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT1); + if (ret < 0) + goto io_error; + if (ret & SDW_SCP_SDCA_INTMASK_SDCA_0) { + ret = sdw_update_no_pm(rt722->slave, SDW_SCP_SDCA_INT1, + SDW_SCP_SDCA_INT_SDCA_0, SDW_SCP_SDCA_INT_SDCA_0); + if (ret < 0) + goto io_error; + } else if (ret & SDW_SCP_SDCA_INTMASK_SDCA_6) { + ret = sdw_update_no_pm(rt722->slave, SDW_SCP_SDCA_INT1, + SDW_SCP_SDCA_INT_SDCA_6, SDW_SCP_SDCA_INT_SDCA_6); + if (ret < 0) + goto io_error; + } + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT2); + if (ret < 0) + goto io_error; + if (ret & SDW_SCP_SDCA_INTMASK_SDCA_8) { + ret = sdw_write_no_pm(rt722->slave, SDW_SCP_SDCA_INT2, + SDW_SCP_SDCA_INTMASK_SDCA_8); + if (ret < 0) + goto io_error; + } + + /* check if flag clear or not */ + ret = sdw_read_no_pm(rt722->slave, SDW_DP0_INT); + if (ret < 0) + goto io_error; + sdca_cascade = ret & SDW_DP0_SDCA_CASCADE; + + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT1); + if (ret < 0) + goto io_error; + scp_sdca_stat1 = ret & SDW_SCP_SDCA_INTMASK_SDCA_0; + + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT2); + if (ret < 0) + goto io_error; + scp_sdca_stat2 = ret & SDW_SCP_SDCA_INTMASK_SDCA_8; + + stat = scp_sdca_stat1 || scp_sdca_stat2 || sdca_cascade; + + count++; + } while (stat != 0 && count < retry); + + if (stat) + dev_warn(&slave->dev, + "%s scp_sdca_stat1=0x%x, scp_sdca_stat2=0x%x\n", __func__, + rt722->scp_sdca_stat1, rt722->scp_sdca_stat2); + + if (status->sdca_cascade && !rt722->disable_irq) + mod_delayed_work(system_power_efficient_wq, + &rt722->jack_detect_work, msecs_to_jiffies(30)); + + mutex_unlock(&rt722->disable_irq_lock); + + return 0; + +io_error: + mutex_unlock(&rt722->disable_irq_lock); + pr_err_ratelimited("IO error in %s, ret %d\n", __func__, ret); + return ret; +} + +static struct sdw_slave_ops rt722_sdca_slave_ops = { + .read_prop = rt722_sdca_read_prop, + .interrupt_callback = rt722_sdca_interrupt_callback, + .update_status = rt722_sdca_update_status, +}; + +static int rt722_sdca_sdw_probe(struct sdw_slave *slave, + const struct sdw_device_id *id) +{ + struct regmap *regmap, *mbq_regmap; + + /* Regmap Initialization */ + mbq_regmap = devm_regmap_init_sdw_mbq(slave, &rt722_sdca_mbq_regmap); + if (IS_ERR(mbq_regmap)) + return PTR_ERR(mbq_regmap); + + regmap = devm_regmap_init_sdw(slave, &rt722_sdca_regmap); + if (IS_ERR(regmap)) + return PTR_ERR(regmap); + + return rt722_sdca_init(&slave->dev, regmap, mbq_regmap, slave); +} + +static int rt722_sdca_sdw_remove(struct sdw_slave *slave) +{ + struct rt722_sdca_priv *rt722 = dev_get_drvdata(&slave->dev); + + if (rt722->hw_init) { + cancel_delayed_work_sync(&rt722->jack_detect_work); + cancel_delayed_work_sync(&rt722->jack_btn_check_work); + } + + if (rt722->first_hw_init) + pm_runtime_disable(&slave->dev); + + mutex_destroy(&rt722->calibrate_mutex); + mutex_destroy(&rt722->disable_irq_lock); + + return 0; +} + +static const struct sdw_device_id rt722_sdca_id[] = { + SDW_SLAVE_ENTRY_EXT(0x025d, 0x722, 0x3, 0x1, 0), + {}, +}; +MODULE_DEVICE_TABLE(sdw, rt722_sdca_id); + +static int __maybe_unused rt722_sdca_dev_suspend(struct device *dev) +{ + struct rt722_sdca_priv *rt722 = dev_get_drvdata(dev); + + if (!rt722->hw_init) + return 0; + + cancel_delayed_work_sync(&rt722->jack_detect_work); + cancel_delayed_work_sync(&rt722->jack_btn_check_work); + + regcache_cache_only(rt722->regmap, true); + regcache_cache_only(rt722->mbq_regmap, true); + + return 0; +} + +static int __maybe_unused rt722_sdca_dev_system_suspend(struct device *dev) +{ + struct rt722_sdca_priv *rt722_sdca = dev_get_drvdata(dev); + struct sdw_slave *slave = dev_to_sdw_dev(dev); + int ret1, ret2; + + if (!rt722_sdca->hw_init) + return 0; + + /* + * prevent new interrupts from being handled after the + * deferred work completes and before the parent disables + * interrupts on the link + */ + mutex_lock(&rt722_sdca->disable_irq_lock); + rt722_sdca->disable_irq = true; + ret1 = sdw_update_no_pm(slave, SDW_SCP_SDCA_INTMASK1, + SDW_SCP_SDCA_INTMASK_SDCA_0 | SDW_SCP_SDCA_INTMASK_SDCA_6, 0); + ret2 = sdw_update_no_pm(slave, SDW_SCP_SDCA_INTMASK2, + SDW_SCP_SDCA_INTMASK_SDCA_8, 0); + mutex_unlock(&rt722_sdca->disable_irq_lock); + + if (ret1 < 0 || ret2 < 0) { + /* log but don't prevent suspend from happening */ + dev_dbg(&slave->dev, "%s: could not disable SDCA interrupts\n:", __func__); + } + + return rt722_sdca_dev_suspend(dev); +} + +#define RT722_PROBE_TIMEOUT 5000 + +static int __maybe_unused rt722_sdca_dev_resume(struct device *dev) +{ + struct sdw_slave *slave = dev_to_sdw_dev(dev); + struct rt722_sdca_priv *rt722 = dev_get_drvdata(dev); + unsigned long time; + + if (!rt722->first_hw_init) + return 0; + + if (!slave->unattach_request) + goto regmap_sync; + + time = wait_for_completion_timeout(&slave->initialization_complete, + msecs_to_jiffies(RT722_PROBE_TIMEOUT)); + if (!time) { + dev_err(&slave->dev, "Initialization not complete, timed out\n"); + sdw_show_ping_status(slave->bus, true); + + return -ETIMEDOUT; + } + +regmap_sync: + slave->unattach_request = 0; + regcache_cache_only(rt722->regmap, false); + regcache_sync(rt722->regmap); + regcache_cache_only(rt722->mbq_regmap, false); + regcache_sync(rt722->mbq_regmap); + return 0; +} + +static const struct dev_pm_ops rt722_sdca_pm = { + SET_SYSTEM_SLEEP_PM_OPS(rt722_sdca_dev_system_suspend, rt722_sdca_dev_resume) + SET_RUNTIME_PM_OPS(rt722_sdca_dev_suspend, rt722_sdca_dev_resume, NULL) +}; + +static struct sdw_driver rt722_sdca_sdw_driver = { + .driver = { + .name = "rt722-sdca", + .owner = THIS_MODULE, + .pm = &rt722_sdca_pm, + }, + .probe = rt722_sdca_sdw_probe, + .remove = rt722_sdca_sdw_remove, + .ops = &rt722_sdca_slave_ops, + .id_table = rt722_sdca_id, +}; +module_sdw_driver(rt722_sdca_sdw_driver); + +MODULE_DESCRIPTION("ASoC RT722 SDCA SDW driver"); +MODULE_AUTHOR("Jack Yu <jack.yu(a)realtek.com>"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/rt722-sdca-sdw.h b/sound/soc/codecs/rt722-sdca-sdw.h new file mode 100644 index 000000000000..5b43e86f75d1 --- /dev/null +++ b/sound/soc/codecs/rt722-sdca-sdw.h @@ -0,0 +1,124 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * rt722-sdca-sdw.h -- RT722 SDCA ALSA SoC audio driver header + * + * Copyright(c) 2023 Realtek Semiconductor Corp. + */ + +#ifndef __RT722_SDW_H__ +#define __RT722_SDW_H__ + +#include <linux/regmap.h> +#include <linux/soundwire/sdw_registers.h> + +static const struct reg_default rt722_sdca_reg_defaults[] = { + { 0x202d, 0x00 }, + { 0x2f01, 0x00 }, + { 0x2f02, 0x09 }, + { 0x2f03, 0x00 }, + { 0x2f04, 0x00 }, + { 0x2f05, 0x0b }, + { 0x2f06, 0x01 }, + { 0x2f08, 0x00 }, + { 0x2f09, 0x00 }, + { 0x2f0a, 0x00 }, + { 0x2f35, 0x00 }, + { 0x2f36, 0x00 }, + { 0x2f50, 0xf0 }, + { 0x2f58, 0x07 }, + { 0x2f59, 0x07 }, + { 0x2f5a, 0x07 }, + { 0x2f5b, 0x07 }, + { 0x2f5c, 0x27 }, + { 0x2f5d, 0x07 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_CS01, RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, + 0), 0x09 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_CS11, RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, + 0), 0x09 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE12, RT722_SDCA_CTL_REQ_POWER_STATE, + 0), 0x03 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE40, RT722_SDCA_CTL_REQ_POWER_STATE, + 0), 0x03 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_MUTE, CH_L), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_MUTE, CH_R), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_MUTE, CH_L), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_MUTE, CH_R), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_CS1F, RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, + 0), 0x09 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_MUTE, CH_01), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_MUTE, CH_02), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_MUTE, CH_03), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_MUTE, CH_04), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_PDE2A, RT722_SDCA_CTL_REQ_POWER_STATE, 0), + 0x03 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_IT26, RT722_SDCA_CTL_VENDOR_DEF, 0), + 0x00 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_CS31, RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), + 0x09 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_MUTE, CH_L), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_MUTE, CH_R), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_PDE23, RT722_SDCA_CTL_REQ_POWER_STATE, 0), + 0x03 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_OT23, RT722_SDCA_CTL_VENDOR_DEF, 0), 0x00 }, +}; + +static const struct reg_default rt722_sdca_mbq_defaults[] = { + { 0x200003c, 0xc214 }, + { 0x2000046, 0x8004 }, + { 0x6100006, 0x0005 }, + { 0x6100010, 0x2630 }, + { 0x6100011, 0x152f }, + { 0x6100013, 0x0102 }, + { 0x6100015, 0x2200 }, + { 0x6100017, 0x0102 }, + { 0x6100025, 0x2a29 }, + { 0x6100026, 0x2a00 }, + { 0x6100028, 0x2a2a }, + { 0x6100029, 0x4141 }, + { 0x6100055, 0x0000 }, + { 0x5810000, 0x702d }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_VOLUME, + CH_L), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_VOLUME, + CH_R), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_VOLUME, + CH_L), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_VOLUME, + CH_R), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, RT722_SDCA_CTL_FU_CH_GAIN, + CH_L), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, RT722_SDCA_CTL_FU_CH_GAIN, + CH_R), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_01), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_02), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_03), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_04), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15, RT722_SDCA_CTL_FU_CH_GAIN, CH_01), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15, RT722_SDCA_CTL_FU_CH_GAIN, CH_02), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15, RT722_SDCA_CTL_FU_CH_GAIN, CH_03), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15, RT722_SDCA_CTL_FU_CH_GAIN, CH_04), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_VOLUME, CH_L), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_VOLUME, CH_R), + 0x0000 }, +}; + +#endif /* __RT722_SDW_H__ */ diff --git a/sound/soc/codecs/rt722-sdca.c b/sound/soc/codecs/rt722-sdca.c new file mode 100644 index 000000000000..9c0d34366c9e --- /dev/null +++ b/sound/soc/codecs/rt722-sdca.c @@ -0,0 +1,1555 @@ +// SPDX-License-Identifier: GPL-2.0-only +// +// rt722-sdca.c -- rt722 SDCA ALSA SoC audio driver +// +// Copyright(c) 2023 Realtek Semiconductor Corp. +// +// + +#include <linux/bitops.h> +#include <sound/core.h> +#include <linux/delay.h> +#include <linux/init.h> +#include <sound/initval.h> +#include <sound/jack.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <sound/pcm.h> +#include <linux/pm_runtime.h> +#include <sound/pcm_params.h> +#include <linux/soundwire/sdw_registers.h> +#include <linux/slab.h> +#include <sound/soc-dapm.h> +#include <sound/tlv.h> + +#include "rt722-sdca.h" + +int rt722_sdca_index_write(struct rt722_sdca_priv *rt722, + unsigned int nid, unsigned int reg, unsigned int value) +{ + struct regmap *regmap = rt722->mbq_regmap; + unsigned int addr = (nid << 20) | reg; + int ret; + + ret = regmap_write(regmap, addr, value); + if (ret < 0) + dev_err(&rt722->slave->dev, + "Failed to set private value: %06x <= %04x ret=%d\n", + addr, value, ret); + + return ret; +} + +int rt722_sdca_index_read(struct rt722_sdca_priv *rt722, + unsigned int nid, unsigned int reg, unsigned int *value) +{ + int ret; + struct regmap *regmap = rt722->mbq_regmap; + unsigned int addr = (nid << 20) | reg; + + ret = regmap_read(regmap, addr, value); + if (ret < 0) + dev_err(&rt722->slave->dev, + "Failed to get private value: %06x => %04x ret=%d\n", + addr, *value, ret); + + return ret; +} + +static int rt722_sdca_index_update_bits(struct rt722_sdca_priv *rt722, + unsigned int nid, unsigned int reg, unsigned int mask, unsigned int val) +{ + unsigned int tmp; + int ret; + + ret = rt722_sdca_index_read(rt722, nid, reg, &tmp); + if (ret < 0) + return ret; + + set_mask_bits(&tmp, mask, val); + return rt722_sdca_index_write(rt722, nid, reg, tmp); +} + +static int rt722_sdca_btn_type(unsigned char *buffer) +{ + if ((*buffer & 0xf0) == 0x10 || (*buffer & 0x0f) == 0x01 || (*(buffer + 1) == 0x01) || + (*(buffer + 1) == 0x10)) + return SND_JACK_BTN_2; + else if ((*buffer & 0xf0) == 0x20 || (*buffer & 0x0f) == 0x02 || (*(buffer + 1) == 0x02) || + (*(buffer + 1) == 0x20)) + return SND_JACK_BTN_3; + else if ((*buffer & 0xf0) == 0x40 || (*buffer & 0x0f) == 0x04 || (*(buffer + 1) == 0x04) || + (*(buffer + 1) == 0x40)) + return SND_JACK_BTN_0; + else if ((*buffer & 0xf0) == 0x80 || (*buffer & 0x0f) == 0x08 || (*(buffer + 1) == 0x08) || + (*(buffer + 1) == 0x80)) + return SND_JACK_BTN_1; + + return 0; +} + +static unsigned int rt722_sdca_button_detect(struct rt722_sdca_priv *rt722) +{ + unsigned int btn_type = 0, offset, idx, val, owner; + int ret; + unsigned char buf[3]; + + /* get current UMP message owner */ + ret = regmap_read(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_CURRENT_OWNER, 0), &owner); + if (ret < 0) + return 0; + + /* if owner is device then there is no button event from device */ + if (owner == 1) + return 0; + + /* read UMP message offset */ + ret = regmap_read(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_MESSAGE_OFFSET, 0), &offset); + if (ret < 0) + goto _end_btn_det_; + + for (idx = 0; idx < sizeof(buf); idx++) { + ret = regmap_read(rt722->regmap, + RT722_BUF_ADDR_HID1 + offset + idx, &val); + if (ret < 0) + goto _end_btn_det_; + buf[idx] = val & 0xff; + } + + if (buf[0] == 0x11) + btn_type = rt722_sdca_btn_type(&buf[1]); + +_end_btn_det_: + /* Host is owner, so set back to device */ + if (owner == 0) + /* set owner to device */ + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_CURRENT_OWNER, 0), 0x01); + + return btn_type; +} + +static int rt722_sdca_headset_detect(struct rt722_sdca_priv *rt722) +{ + unsigned int det_mode; + int ret; + + /* get detected_mode */ + ret = regmap_read(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, + RT722_SDCA_CTL_DETECTED_MODE, 0), &det_mode); + if (ret < 0) + goto io_error; + + switch (det_mode) { + case 0x00: + rt722->jack_type = 0; + break; + case 0x03: + rt722->jack_type = SND_JACK_HEADPHONE; + break; + case 0x05: + rt722->jack_type = SND_JACK_HEADSET; + break; + } + + /* write selected_mode */ + if (det_mode) { + ret = regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, + RT722_SDCA_CTL_SELECTED_MODE, 0), det_mode); + if (ret < 0) + goto io_error; + } + + dev_dbg(&rt722->slave->dev, + "%s, detected_mode=0x%x\n", __func__, det_mode); + + return 0; + +io_error: + pr_err_ratelimited("IO error in %s, ret %d\n", __func__, ret); + return ret; +} + +static void rt722_sdca_jack_detect_handler(struct work_struct *work) +{ + struct rt722_sdca_priv *rt722 = + container_of(work, struct rt722_sdca_priv, jack_detect_work.work); + int btn_type = 0, ret; + + if (!rt722->hs_jack) + return; + + if (!rt722->component->card || !rt722->component->card->instantiated) + return; + + /* SDW_SCP_SDCA_INT_SDCA_6 is used for jack detection */ + if (rt722->scp_sdca_stat1 & SDW_SCP_SDCA_INT_SDCA_6 || + rt722->scp_sdca_stat1 & SDW_SCP_SDCA_INT_SDCA_0) { + ret = rt722_sdca_headset_detect(rt722); + if (ret < 0) + return; + } + + /* SDW_SCP_SDCA_INT_SDCA_8 is used for button detection */ + if (rt722->scp_sdca_stat2 & SDW_SCP_SDCA_INT_SDCA_8) + btn_type = rt722_sdca_button_detect(rt722); + + if (rt722->jack_type == 0) + btn_type = 0; + + dev_dbg(&rt722->slave->dev, + "in %s, jack_type=%d\n", __func__, rt722->jack_type); + dev_dbg(&rt722->slave->dev, + "in %s, btn_type=0x%x\n", __func__, btn_type); + dev_dbg(&rt722->slave->dev, + "in %s, scp_sdca_stat1=0x%x, scp_sdca_stat2=0x%x\n", __func__, + rt722->scp_sdca_stat1, rt722->scp_sdca_stat2); + + snd_soc_jack_report(rt722->hs_jack, rt722->jack_type | btn_type, + SND_JACK_HEADSET | + SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3); + + if (btn_type) { + /* button released */ + snd_soc_jack_report(rt722->hs_jack, rt722->jack_type, + SND_JACK_HEADSET | + SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3); + + mod_delayed_work(system_power_efficient_wq, + &rt722->jack_btn_check_work, msecs_to_jiffies(200)); + } +} + +static void rt722_sdca_btn_check_handler(struct work_struct *work) +{ + struct rt722_sdca_priv *rt722 = + container_of(work, struct rt722_sdca_priv, jack_btn_check_work.work); + int btn_type = 0, ret, idx; + unsigned int det_mode, offset, val; + unsigned char buf[3]; + + ret = regmap_read(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, + RT722_SDCA_CTL_DETECTED_MODE, 0), &det_mode); + if (ret < 0) + goto io_error; + + /* pin attached */ + if (det_mode) { + /* read UMP message offset */ + ret = regmap_read(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_MESSAGE_OFFSET, 0), &offset); + if (ret < 0) + goto io_error; + + for (idx = 0; idx < sizeof(buf); idx++) { + ret = regmap_read(rt722->regmap, + RT722_BUF_ADDR_HID1 + offset + idx, &val); + if (ret < 0) + goto io_error; + buf[idx] = val & 0xff; + } + + if (buf[0] == 0x11) + btn_type = rt722_sdca_btn_type(&buf[1]); + } else + rt722->jack_type = 0; + + dev_dbg(&rt722->slave->dev, "%s, btn_type=0x%x\n", __func__, btn_type); + snd_soc_jack_report(rt722->hs_jack, rt722->jack_type | btn_type, + SND_JACK_HEADSET | + SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3); + + if (btn_type) { + /* button released */ + snd_soc_jack_report(rt722->hs_jack, rt722->jack_type, + SND_JACK_HEADSET | + SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3); + + mod_delayed_work(system_power_efficient_wq, + &rt722->jack_btn_check_work, msecs_to_jiffies(200)); + } + + return; + +io_error: + pr_err_ratelimited("IO error in %s, ret %d\n", __func__, ret); +} + +static void rt722_sdca_jack_init(struct rt722_sdca_priv *rt722) +{ + mutex_lock(&rt722->calibrate_mutex); + if (rt722->hs_jack) { + /* set SCP_SDCA_IntMask1[0]=1 */ + sdw_write_no_pm(rt722->slave, SDW_SCP_SDCA_INTMASK1, + SDW_SCP_SDCA_INTMASK_SDCA_0 | SDW_SCP_SDCA_INTMASK_SDCA_6); + /* set SCP_SDCA_IntMask2[0]=1 */ + sdw_write_no_pm(rt722->slave, SDW_SCP_SDCA_INTMASK2, + SDW_SCP_SDCA_INTMASK_SDCA_8); + dev_dbg(&rt722->slave->dev, "in %s enable\n", __func__); + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_HDA_LEGACY_UNSOL_CTL, 0x016E); + /* set XU(et03h) & XU(et0Dh) to Not bypassed */ + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_XU03, + RT722_SDCA_CTL_SELECTED_MODE, 0), 0); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_XU0D, + RT722_SDCA_CTL_SELECTED_MODE, 0), 0); + /* trigger GE interrupt */ + rt722_sdca_index_update_bits(rt722, RT722_VENDOR_HDA_CTL, + RT722_GE_RELATED_CTL2, 0x4000, 0x4000); + } + mutex_unlock(&rt722->calibrate_mutex); +} + +static int rt722_sdca_set_jack_detect(struct snd_soc_component *component, + struct snd_soc_jack *hs_jack, void *data) +{ + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + int ret; + + rt722->hs_jack = hs_jack; + + ret = pm_runtime_resume_and_get(component->dev); + if (ret < 0) { + if (ret != -EACCES) { + dev_err(component->dev, "%s: failed to resume %d\n", __func__, ret); + return ret; + } + /* pm_runtime not enabled yet */ + dev_dbg(component->dev, "%s: skipping jack init for now\n", __func__); + return 0; + } + + rt722_sdca_jack_init(rt722); + + pm_runtime_mark_last_busy(component->dev); + pm_runtime_put_autosuspend(component->dev); + + return 0; +} + +/* For SDCA control DAC/ADC Gain */ +static int rt722_sdca_set_gain_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned int read_l, read_r, gain_l_val, gain_r_val; + unsigned int adc_vol_flag = 0, changed = 0; + unsigned int lvalue, rvalue; + const unsigned int interval_offset = 0xc0; + const unsigned int tendB = 0xa00; + + if (strstr(ucontrol->id.name, "FU1E Capture Volume") || + strstr(ucontrol->id.name, "FU0F Capture Volume")) + adc_vol_flag = 1; + + regmap_read(rt722->mbq_regmap, mc->reg, &lvalue); + regmap_read(rt722->mbq_regmap, mc->rreg, &rvalue); + + /* L Channel */ + gain_l_val = ucontrol->value.integer.value[0]; + if (gain_l_val > mc->max) + gain_l_val = mc->max; + + if (mc->shift == 8) /* boost gain */ + gain_l_val = gain_l_val * tendB; + else { + /* ADC/DAC gain */ + if (adc_vol_flag) + gain_l_val = 0x1e00 - ((mc->max - gain_l_val) * interval_offset); + else + gain_l_val = 0 - ((mc->max - gain_l_val) * interval_offset); + gain_l_val &= 0xffff; + } + + /* R Channel */ + gain_r_val = ucontrol->value.integer.value[1]; + if (gain_r_val > mc->max) + gain_r_val = mc->max; + + if (mc->shift == 8) /* boost gain */ + gain_r_val = gain_r_val * tendB; + else { + /* ADC/DAC gain */ + if (adc_vol_flag) + gain_r_val = 0x1e00 - ((mc->max - gain_r_val) * interval_offset); + else + gain_r_val = 0 - ((mc->max - gain_r_val) * interval_offset); + gain_r_val &= 0xffff; + } + + if (lvalue != gain_l_val || rvalue != gain_r_val) + changed = 1; + else + return 0; + + /* Lch*/ + regmap_write(rt722->mbq_regmap, mc->reg, gain_l_val); + + /* Rch */ + regmap_write(rt722->mbq_regmap, mc->rreg, gain_r_val); + + regmap_read(rt722->mbq_regmap, mc->reg, &read_l); + regmap_read(rt722->mbq_regmap, mc->rreg, &read_r); + if (read_r == gain_r_val && read_l == gain_l_val) + return changed; + + return -EIO; +} + +static int rt722_sdca_set_gain_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + unsigned int read_l, read_r, ctl_l = 0, ctl_r = 0; + unsigned int adc_vol_flag = 0; + const unsigned int interval_offset = 0xc0; + const unsigned int tendB = 0xa00; + + if (strstr(ucontrol->id.name, "FU1E Capture Volume") || + strstr(ucontrol->id.name, "FU0F Capture Volume")) + adc_vol_flag = 1; + + regmap_read(rt722->mbq_regmap, mc->reg, &read_l); + regmap_read(rt722->mbq_regmap, mc->rreg, &read_r); + + if (mc->shift == 8) /* boost gain */ + ctl_l = read_l / tendB; + else { + if (adc_vol_flag) + ctl_l = mc->max - (((0x1e00 - read_l) & 0xffff) / interval_offset); + else + ctl_l = mc->max - (((0 - read_l) & 0xffff) / interval_offset); + } + + if (read_l != read_r) { + if (mc->shift == 8) /* boost gain */ + ctl_r = read_r / tendB; + else { /* ADC/DAC gain */ + if (adc_vol_flag) + ctl_r = mc->max - (((0x1e00 - read_r) & 0xffff) / interval_offset); + else + ctl_r = mc->max - (((0 - read_r) & 0xffff) / interval_offset); + } + } else { + ctl_r = ctl_l; + } + + ucontrol->value.integer.value[0] = ctl_l; + ucontrol->value.integer.value[1] = ctl_r; + + return 0; +} + +static int rt722_sdca_set_fu1e_capture_ctl(struct rt722_sdca_priv *rt722) +{ + int err, i; + unsigned int ch_mute; + + for (i = 0; i < ARRAY_SIZE(rt722->fu1e_mixer_mute); i++) { + ch_mute = rt722->fu1e_dapm_mute || rt722->fu1e_mixer_mute[i]; + err = regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, + RT722_SDCA_CTL_FU_MUTE, CH_01) + i, ch_mute); + if (err < 0) + return err; + } + + return 0; +} + +static int rt722_sdca_fu1e_capture_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct rt722_sdca_dmic_kctrl_priv *p = + (struct rt722_sdca_dmic_kctrl_priv *)kcontrol->private_value; + unsigned int i; + + for (i = 0; i < p->count; i++) + ucontrol->value.integer.value[i] = !rt722->fu1e_mixer_mute[i]; + + return 0; +} + +static int rt722_sdca_fu1e_capture_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct rt722_sdca_dmic_kctrl_priv *p = + (struct rt722_sdca_dmic_kctrl_priv *)kcontrol->private_value; + int err, changed = 0, i; + + for (i = 0; i < p->count; i++) { + if (rt722->fu1e_mixer_mute[i] != !ucontrol->value.integer.value[i]) + changed = 1; + rt722->fu1e_mixer_mute[i] = !ucontrol->value.integer.value[i]; + } + + err = rt722_sdca_set_fu1e_capture_ctl(rt722); + if (err < 0) + return err; + + return changed; +} + +static int rt722_sdca_set_fu0f_capture_ctl(struct rt722_sdca_priv *rt722) +{ + int err; + unsigned int ch_l, ch_r; + + ch_l = (rt722->fu0f_dapm_mute || rt722->fu0f_mixer_l_mute) ? 0x01 : 0x00; + ch_r = (rt722->fu0f_dapm_mute || rt722->fu0f_mixer_r_mute) ? 0x01 : 0x00; + + err = regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, + RT722_SDCA_CTL_FU_MUTE, CH_L), ch_l); + if (err < 0) + return err; + + err = regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, + RT722_SDCA_CTL_FU_MUTE, CH_R), ch_r); + if (err < 0) + return err; + + return 0; +} + +static int rt722_sdca_fu0f_capture_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + + ucontrol->value.integer.value[0] = !rt722->fu0f_mixer_l_mute; + ucontrol->value.integer.value[1] = !rt722->fu0f_mixer_r_mute; + return 0; +} + +static int rt722_sdca_fu0f_capture_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + int err, changed = 0; + + if (rt722->fu0f_mixer_l_mute != !ucontrol->value.integer.value[0] || + rt722->fu0f_mixer_r_mute != !ucontrol->value.integer.value[1]) + changed = 1; + + rt722->fu0f_mixer_l_mute = !ucontrol->value.integer.value[0]; + rt722->fu0f_mixer_r_mute = !ucontrol->value.integer.value[1]; + err = rt722_sdca_set_fu0f_capture_ctl(rt722); + if (err < 0) + return err; + + return changed; +} + +static int rt722_sdca_fu_info(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + struct rt722_sdca_dmic_kctrl_priv *p = + (struct rt722_sdca_dmic_kctrl_priv *)kcontrol->private_value; + + if (p->max == 1) + uinfo->type = SNDRV_CTL_ELEM_TYPE_BOOLEAN; + else + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = p->count; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = p->max; + return 0; +} + +static int rt722_sdca_dmic_set_gain_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct rt722_sdca_dmic_kctrl_priv *p = + (struct rt722_sdca_dmic_kctrl_priv *)kcontrol->private_value; + unsigned int boost_step = 0x0a00; + unsigned int vol_max = 0x1e00; + unsigned int regvalue, ctl, i; + unsigned int adc_vol_flag = 0; + const unsigned int interval_offset = 0xc0; + + if (strstr(ucontrol->id.name, "FU1E Capture Volume")) + adc_vol_flag = 1; + + /* check all channels */ + for (i = 0; i < p->count; i++) { + regmap_read(rt722->mbq_regmap, p->reg_base + i, &regvalue); + + if (!adc_vol_flag) /* boost gain */ + ctl = regvalue / boost_step; + else { /* ADC gain */ + if (adc_vol_flag) + ctl = p->max - (((vol_max - regvalue) & 0xffff) / interval_offset); + else + ctl = p->max - (((0 - regvalue) & 0xffff) / interval_offset); + } + + ucontrol->value.integer.value[i] = ctl; + } + + return 0; +} + +static int rt722_sdca_dmic_set_gain_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_dmic_kctrl_priv *p = + (struct rt722_sdca_dmic_kctrl_priv *)kcontrol->private_value; + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned int boost_step = 0x0a00; + unsigned int vol_max = 0x1e00; + unsigned int gain_val[4]; + unsigned int i, adc_vol_flag = 0, changed = 0; + unsigned int regvalue[4]; + const unsigned int interval_offset = 0xc0; + int err; + + if (strstr(ucontrol->id.name, "FU1E Capture Volume")) + adc_vol_flag = 1; + + /* check all channels */ + for (i = 0; i < p->count; i++) { + regmap_read(rt722->mbq_regmap, p->reg_base + i, &regvalue[i]); + + gain_val[i] = ucontrol->value.integer.value[i]; + if (gain_val[i] > p->max) + gain_val[i] = p->max; + + if (!adc_vol_flag) /* boost gain */ + gain_val[i] = gain_val[i] * boost_step; + else { /* ADC gain */ + gain_val[i] = vol_max - ((p->max - gain_val[i]) * interval_offset); + gain_val[i] &= 0xffff; + } + + if (regvalue[i] != gain_val[i]) + changed = 1; + } + + if (!changed) + return 0; + + for (i = 0; i < p->count; i++) { + err = regmap_write(rt722->mbq_regmap, p->reg_base + i, gain_val[i]); + if (err < 0) + dev_err(&rt722->slave->dev, "%#08x can't be set\n", p->reg_base + i); + } + + return changed; +} + +#define RT722_SDCA_PR_VALUE(xreg_base, xcount, xmax, xinvert) \ + ((unsigned long)&(struct rt722_sdca_dmic_kctrl_priv) \ + {.reg_base = xreg_base, .count = xcount, .max = xmax, \ + .invert = xinvert}) + +#define RT722_SDCA_FU_CTRL(xname, reg_base, xmax, xinvert, xcount) \ +{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname), \ + .info = rt722_sdca_fu_info, \ + .get = rt722_sdca_fu1e_capture_get, \ + .put = rt722_sdca_fu1e_capture_put, \ + .private_value = RT722_SDCA_PR_VALUE(reg_base, xcount, xmax, xinvert)} + +#define RT722_SDCA_EXT_TLV(xname, reg_base, xhandler_get,\ + xhandler_put, xcount, xmax, tlv_array) \ +{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname), \ + .access = SNDRV_CTL_ELEM_ACCESS_TLV_READ | \ + SNDRV_CTL_ELEM_ACCESS_READWRITE, \ + .tlv.p = (tlv_array), \ + .info = rt722_sdca_fu_info, \ + .get = xhandler_get, .put = xhandler_put, \ + .private_value = RT722_SDCA_PR_VALUE(reg_base, xcount, xmax, 0) } + +static const DECLARE_TLV_DB_SCALE(out_vol_tlv, -6525, 75, 0); +static const DECLARE_TLV_DB_SCALE(mic_vol_tlv, -1725, 75, 0); +static const DECLARE_TLV_DB_SCALE(boost_vol_tlv, 0, 1000, 0); + +static const struct snd_kcontrol_new rt722_sdca_controls[] = { + /* Headphone playback settings */ + SOC_DOUBLE_R_EXT_TLV("FU05 Playback Volume", + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_VOLUME, CH_L), + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_VOLUME, CH_R), 0, 0x57, 0, + rt722_sdca_set_gain_get, rt722_sdca_set_gain_put, out_vol_tlv), + /* Headset mic capture settings */ + SOC_DOUBLE_EXT("FU0F Capture Switch", SND_SOC_NOPM, 0, 1, 1, 0, + rt722_sdca_fu0f_capture_get, rt722_sdca_fu0f_capture_put), + SOC_DOUBLE_R_EXT_TLV("FU0F Capture Volume", + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, + RT722_SDCA_CTL_FU_VOLUME, CH_L), + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, + RT722_SDCA_CTL_FU_VOLUME, CH_R), 0, 0x3f, 0, + rt722_sdca_set_gain_get, rt722_sdca_set_gain_put, mic_vol_tlv), + SOC_DOUBLE_R_EXT_TLV("FU33 Boost Volume", + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, + RT722_SDCA_CTL_FU_CH_GAIN, CH_L), + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, + RT722_SDCA_CTL_FU_CH_GAIN, CH_R), 8, 3, 0, + rt722_sdca_set_gain_get, rt722_sdca_set_gain_put, boost_vol_tlv), + /* AMP playback settings */ + SOC_DOUBLE_R_EXT_TLV("FU06 Playback Volume", + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_VOLUME, CH_L), + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_VOLUME, CH_R), 0, 0x57, 0, + rt722_sdca_set_gain_get, rt722_sdca_set_gain_put, out_vol_tlv), + /* DMIC capture settings */ + RT722_SDCA_FU_CTRL("FU1E Capture Switch", + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, + RT722_SDCA_CTL_FU_MUTE, CH_01), 1, 1, 4), + RT722_SDCA_EXT_TLV("FU1E Capture Volume", + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, + RT722_SDCA_CTL_FU_VOLUME, CH_01), + rt722_sdca_dmic_set_gain_get, rt722_sdca_dmic_set_gain_put, + 4, 0x3f, mic_vol_tlv), + RT722_SDCA_EXT_TLV("FU15 Boost Volume", + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15, + RT722_SDCA_CTL_FU_CH_GAIN, CH_01), + rt722_sdca_dmic_set_gain_get, rt722_sdca_dmic_set_gain_put, + 4, 3, boost_vol_tlv), +}; + +static int rt722_sdca_adc_mux_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = + snd_soc_dapm_kcontrol_component(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned int val = 0, mask_sft; + + if (strstr(ucontrol->id.name, "ADC 22 Mux")) + mask_sft = 12; + else if (strstr(ucontrol->id.name, "ADC 24 Mux")) + mask_sft = 4; + else if (strstr(ucontrol->id.name, "ADC 25 Mux")) + mask_sft = 0; + else + return -EINVAL; + + rt722_sdca_index_read(rt722, RT722_VENDOR_HDA_CTL, + RT722_HDA_LEGACY_MUX_CTL0, &val); + + ucontrol->value.enumerated.item[0] = (val >> mask_sft) & 0x7; + + return 0; +} + +static int rt722_sdca_adc_mux_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = + snd_soc_dapm_kcontrol_component(kcontrol); + struct snd_soc_dapm_context *dapm = + snd_soc_dapm_kcontrol_dapm(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct soc_enum *e = (struct soc_enum *)kcontrol->private_value; + unsigned int *item = ucontrol->value.enumerated.item; + unsigned int val, val2 = 0, change, mask_sft; + + if (item[0] >= e->items) + return -EINVAL; + + if (strstr(ucontrol->id.name, "ADC 22 Mux")) + mask_sft = 12; + else if (strstr(ucontrol->id.name, "ADC 24 Mux")) + mask_sft = 4; + else if (strstr(ucontrol->id.name, "ADC 25 Mux")) + mask_sft = 0; + else + return -EINVAL; + + val = snd_soc_enum_item_to_val(e, item[0]) << e->shift_l; + + rt722_sdca_index_read(rt722, RT722_VENDOR_HDA_CTL, + RT722_HDA_LEGACY_MUX_CTL0, &val2); + val2 = (0x7 << mask_sft) & val2; + + if (val == val2) + change = 0; + else + change = 1; + + if (change) + rt722_sdca_index_update_bits(rt722, RT722_VENDOR_HDA_CTL, + RT722_HDA_LEGACY_MUX_CTL0, 0x7 << mask_sft, + val << mask_sft); + + snd_soc_dapm_mux_update_power(dapm, kcontrol, + item[0], e, NULL); + + return change; +} + +static const char * const adc22_mux_text[] = { + "MIC2", + "LINE1", + "LINE2", +}; + +static const char * const adc07_10_mux_text[] = { + "DMIC1", + "DMIC2", +}; + +static SOC_ENUM_SINGLE_DECL( + rt722_adc22_enum, SND_SOC_NOPM, 0, adc22_mux_text); + +static SOC_ENUM_SINGLE_DECL( + rt722_adc24_enum, SND_SOC_NOPM, 0, adc07_10_mux_text); + +static SOC_ENUM_SINGLE_DECL( + rt722_adc25_enum, SND_SOC_NOPM, 0, adc07_10_mux_text); + +static const struct snd_kcontrol_new rt722_sdca_adc22_mux = + SOC_DAPM_ENUM_EXT("ADC 22 Mux", rt722_adc22_enum, + rt722_sdca_adc_mux_get, rt722_sdca_adc_mux_put); + +static const struct snd_kcontrol_new rt722_sdca_adc24_mux = + SOC_DAPM_ENUM_EXT("ADC 24 Mux", rt722_adc24_enum, + rt722_sdca_adc_mux_get, rt722_sdca_adc_mux_put); + +static const struct snd_kcontrol_new rt722_sdca_adc25_mux = + SOC_DAPM_ENUM_EXT("ADC 25 Mux", rt722_adc25_enum, + rt722_sdca_adc_mux_get, rt722_sdca_adc_mux_put); + +static int rt722_sdca_fu42_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char unmute = 0x0, mute = 0x1; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_MUTE, CH_L), unmute); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_MUTE, CH_R), unmute); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_MUTE, CH_L), mute); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_MUTE, CH_R), mute); + break; + } + return 0; +} + +static int rt722_sdca_fu21_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char unmute = 0x0, mute = 0x1; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_MUTE, CH_L), unmute); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_MUTE, CH_R), unmute); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_MUTE, CH_L), mute); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_MUTE, CH_R), mute); + break; + } + return 0; +} + +static int rt722_sdca_fu113_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + rt722->fu1e_dapm_mute = false; + rt722_sdca_set_fu1e_capture_ctl(rt722); + break; + case SND_SOC_DAPM_PRE_PMD: + rt722->fu1e_dapm_mute = true; + rt722_sdca_set_fu1e_capture_ctl(rt722); + break; + } + return 0; +} + +static int rt722_sdca_fu36_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + rt722->fu0f_dapm_mute = false; + rt722_sdca_set_fu0f_capture_ctl(rt722); + break; + case SND_SOC_DAPM_PRE_PMD: + rt722->fu0f_dapm_mute = true; + rt722_sdca_set_fu0f_capture_ctl(rt722); + break; + } + return 0; +} + +static int rt722_sdca_pde47_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char ps0 = 0x0, ps3 = 0x3; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE40, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE40, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps3); + break; + } + return 0; +} + +static int rt722_sdca_pde23_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char ps0 = 0x0, ps3 = 0x3; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_PDE23, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_PDE23, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps3); + break; + } + return 0; +} + +static int rt722_sdca_pde11_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char ps0 = 0x0, ps3 = 0x3; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_PDE2A, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_PDE2A, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps3); + break; + } + return 0; +} + +static int rt722_sdca_pde12_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char ps0 = 0x0, ps3 = 0x3; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE12, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE12, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps3); + break; + } + return 0; +} + +static const struct snd_soc_dapm_widget rt722_sdca_dapm_widgets[] = { + SND_SOC_DAPM_OUTPUT("HP"), + SND_SOC_DAPM_OUTPUT("SPK"), + SND_SOC_DAPM_INPUT("MIC2"), + SND_SOC_DAPM_INPUT("LINE1"), + SND_SOC_DAPM_INPUT("LINE2"), + SND_SOC_DAPM_INPUT("DMIC1_2"), + SND_SOC_DAPM_INPUT("DMIC3_4"), + + SND_SOC_DAPM_SUPPLY("PDE 23", SND_SOC_NOPM, 0, 0, + rt722_sdca_pde23_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_SUPPLY("PDE 47", SND_SOC_NOPM, 0, 0, + rt722_sdca_pde47_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_SUPPLY("PDE 11", SND_SOC_NOPM, 0, 0, + rt722_sdca_pde11_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_SUPPLY("PDE 12", SND_SOC_NOPM, 0, 0, + rt722_sdca_pde12_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + + SND_SOC_DAPM_DAC_E("FU 21", NULL, SND_SOC_NOPM, 0, 0, + rt722_sdca_fu21_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_DAC_E("FU 42", NULL, SND_SOC_NOPM, 0, 0, + rt722_sdca_fu42_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_ADC_E("FU 36", NULL, SND_SOC_NOPM, 0, 0, + rt722_sdca_fu36_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_ADC_E("FU 113", NULL, SND_SOC_NOPM, 0, 0, + rt722_sdca_fu113_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_MUX("ADC 22 Mux", SND_SOC_NOPM, 0, 0, + &rt722_sdca_adc22_mux), + SND_SOC_DAPM_MUX("ADC 24 Mux", SND_SOC_NOPM, 0, 0, + &rt722_sdca_adc24_mux), + SND_SOC_DAPM_MUX("ADC 25 Mux", SND_SOC_NOPM, 0, 0, + &rt722_sdca_adc25_mux), + + SND_SOC_DAPM_AIF_IN("DP1RX", "DP1 Headphone Playback", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_OUT("DP2TX", "DP2 Headset Capture", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_IN("DP3RX", "DP3 Speaker Playback", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_OUT("DP6TX", "DP6 DMic Capture", 0, SND_SOC_NOPM, 0, 0), +}; + +static const struct snd_soc_dapm_route rt722_sdca_audio_map[] = { + {"FU 42", NULL, "DP1RX"}, + {"FU 21", NULL, "DP3RX"}, + + {"ADC 22 Mux", "MIC2", "MIC2"}, + {"ADC 22 Mux", "LINE1", "LINE1"}, + {"ADC 22 Mux", "LINE2", "LINE2"}, + {"ADC 24 Mux", "DMIC1", "DMIC1_2"}, + {"ADC 24 Mux", "DMIC2", "DMIC3_4"}, + {"ADC 25 Mux", "DMIC1", "DMIC1_2"}, + {"ADC 25 Mux", "DMIC2", "DMIC3_4"}, + {"FU 36", NULL, "PDE 12"}, + {"FU 36", NULL, "ADC 22 Mux"}, + {"FU 113", NULL, "PDE 11"}, + {"FU 113", NULL, "ADC 24 Mux"}, + {"FU 113", NULL, "ADC 25 Mux"}, + {"DP2TX", NULL, "FU 36"}, + {"DP6TX", NULL, "FU 113"}, + + {"HP", NULL, "PDE 47"}, + {"HP", NULL, "FU 42"}, + {"SPK", NULL, "PDE 23"}, + {"SPK", NULL, "FU 21"}, +}; + +static int rt722_sdca_parse_dt(struct rt722_sdca_priv *rt722, struct device *dev) +{ + device_property_read_u32(dev, "realtek,jd-src", &rt722->jd_src); + + return 0; +} + +static int rt722_sdca_probe(struct snd_soc_component *component) +{ + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + int ret; + + rt722_sdca_parse_dt(rt722, &rt722->slave->dev); + rt722->component = component; + + ret = pm_runtime_resume(component->dev); + if (ret < 0 && ret != -EACCES) + return ret; + + return 0; +} + +static const struct snd_soc_component_driver soc_sdca_dev_rt722 = { + .probe = rt722_sdca_probe, + .controls = rt722_sdca_controls, + .num_controls = ARRAY_SIZE(rt722_sdca_controls), + .dapm_widgets = rt722_sdca_dapm_widgets, + .num_dapm_widgets = ARRAY_SIZE(rt722_sdca_dapm_widgets), + .dapm_routes = rt722_sdca_audio_map, + .num_dapm_routes = ARRAY_SIZE(rt722_sdca_audio_map), + .set_jack = rt722_sdca_set_jack_detect, + .endianness = 1, +}; + +static int rt722_sdca_set_sdw_stream(struct snd_soc_dai *dai, void *sdw_stream, + int direction) +{ + snd_soc_dai_dma_data_set(dai, direction, sdw_stream); + + return 0; +} + +static void rt722_sdca_shutdown(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + snd_soc_dai_set_dma_data(dai, substream, NULL); +} + +static int rt722_sdca_pcm_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_component *component = dai->component; + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct sdw_stream_config stream_config; + struct sdw_port_config port_config; + enum sdw_data_direction direction; + struct sdw_stream_runtime *sdw_stream; + int retval, port, num_channels; + unsigned int sampling_rate; + + dev_dbg(dai->dev, "%s %s", __func__, dai->name); + sdw_stream = snd_soc_dai_get_dma_data(dai, substream); + + if (!sdw_stream) + return -EINVAL; + + if (!rt722->slave) + return -EINVAL; + + /* + * RT722_AIF1 with port = 1 for headphone playback + * RT722_AIF1 with port = 2 for headset-mic capture + * RT722_AIF2 with port = 3 for speaker playback + * RT722_AIF3 with port = 6 for digital-mic capture + */ + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) { + direction = SDW_DATA_DIR_RX; + if (dai->id == RT722_AIF1) + port = 1; + else if (dai->id == RT722_AIF2) + port = 3; + else + return -EINVAL; + } else { + direction = SDW_DATA_DIR_TX; + if (dai->id == RT722_AIF1) + port = 2; + else if (dai->id == RT722_AIF3) + port = 6; + else + return -EINVAL; + } + stream_config.frame_rate = params_rate(params); + stream_config.ch_count = params_channels(params); + stream_config.bps = snd_pcm_format_width(params_format(params)); + stream_config.direction = direction; + + num_channels = params_channels(params); + port_config.ch_mask = GENMASK(num_channels - 1, 0); + port_config.num = port; + + retval = sdw_stream_add_slave(rt722->slave, &stream_config, + &port_config, 1, sdw_stream); + if (retval) { + dev_err(dai->dev, "Unable to configure port\n"); + return retval; + } + + if (params_channels(params) > 16) { + dev_err(component->dev, "Unsupported channels %d\n", + params_channels(params)); + return -EINVAL; + } + + /* sampling rate configuration */ + switch (params_rate(params)) { + case 44100: + sampling_rate = RT722_SDCA_RATE_44100HZ; + break; + case 48000: + sampling_rate = RT722_SDCA_RATE_48000HZ; + break; + case 96000: + sampling_rate = RT722_SDCA_RATE_96000HZ; + break; + case 192000: + sampling_rate = RT722_SDCA_RATE_192000HZ; + break; + default: + dev_err(component->dev, "Rate %d is not supported\n", + params_rate(params)); + return -EINVAL; + } + + /* set sampling frequency */ + if (dai->id == RT722_AIF1) { + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_CS01, + RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), sampling_rate); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_CS11, + RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), sampling_rate); + } + + if (dai->id == RT722_AIF2) + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_CS31, + RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), sampling_rate); + + if (dai->id == RT722_AIF3) + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_CS1F, + RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), sampling_rate); + + return 0; +} + +static int rt722_sdca_pcm_hw_free(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct snd_soc_component *component = dai->component; + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct sdw_stream_runtime *sdw_stream = + snd_soc_dai_get_dma_data(dai, substream); + + if (!rt722->slave) + return -EINVAL; + + sdw_stream_remove_slave(rt722->slave, sdw_stream); + return 0; +} + +#define RT722_STEREO_RATES (SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000 | \ + SNDRV_PCM_RATE_96000 | SNDRV_PCM_RATE_192000) +#define RT722_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE | \ + SNDRV_PCM_FMTBIT_S24_LE) + +static const struct snd_soc_dai_ops rt722_sdca_ops = { + .hw_params = rt722_sdca_pcm_hw_params, + .hw_free = rt722_sdca_pcm_hw_free, + .set_stream = rt722_sdca_set_sdw_stream, + .shutdown = rt722_sdca_shutdown, +}; + +static struct snd_soc_dai_driver rt722_sdca_dai[] = { + { + .name = "rt722-sdca-aif1", + .id = RT722_AIF1, + .playback = { + .stream_name = "DP1 Headphone Playback", + .channels_min = 1, + .channels_max = 2, + .rates = RT722_STEREO_RATES, + .formats = RT722_FORMATS, + }, + .capture = { + .stream_name = "DP2 Headset Capture", + .channels_min = 1, + .channels_max = 2, + .rates = RT722_STEREO_RATES, + .formats = RT722_FORMATS, + }, + .ops = &rt722_sdca_ops, + }, + { + .name = "rt722-sdca-aif2", + .id = RT722_AIF2, + .playback = { + .stream_name = "DP3 Speaker Playback", + .channels_min = 1, + .channels_max = 2, + .rates = RT722_STEREO_RATES, + .formats = RT722_FORMATS, + }, + .ops = &rt722_sdca_ops, + }, + { + .name = "rt722-sdca-aif3", + .id = RT722_AIF3, + .capture = { + .stream_name = "DP6 DMic Capture", + .channels_min = 1, + .channels_max = 2, + .rates = RT722_STEREO_RATES, + .formats = RT722_FORMATS, + }, + .ops = &rt722_sdca_ops, + } +}; + +int rt722_sdca_init(struct device *dev, struct regmap *regmap, + struct regmap *mbq_regmap, struct sdw_slave *slave) +{ + struct rt722_sdca_priv *rt722; + + rt722 = devm_kzalloc(dev, sizeof(*rt722), GFP_KERNEL); + if (!rt722) + return -ENOMEM; + + dev_set_drvdata(dev, rt722); + rt722->slave = slave; + rt722->regmap = regmap; + rt722->mbq_regmap = mbq_regmap; + + mutex_init(&rt722->calibrate_mutex); + mutex_init(&rt722->disable_irq_lock); + + INIT_DELAYED_WORK(&rt722->jack_detect_work, rt722_sdca_jack_detect_handler); + INIT_DELAYED_WORK(&rt722->jack_btn_check_work, rt722_sdca_btn_check_handler); + + /* + * Mark hw_init to false + * HW init will be performed when device reports present + */ + rt722->hw_init = false; + rt722->first_hw_init = false; + rt722->fu1e_dapm_mute = true; + rt722->fu0f_dapm_mute = true; + rt722->fu0f_mixer_l_mute = rt722->fu0f_mixer_r_mute = true; + rt722->fu1e_mixer_mute[0] = rt722->fu1e_mixer_mute[1] = + rt722->fu1e_mixer_mute[2] = rt722->fu1e_mixer_mute[3] = true; + + return devm_snd_soc_register_component(dev, + &soc_sdca_dev_rt722, rt722_sdca_dai, ARRAY_SIZE(rt722_sdca_dai)); +} + +static void rt722_sdca_dmic_preset(struct rt722_sdca_priv *rt722) +{ + /* Set AD07 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_ADC0A_08_PDE_FLOAT_CTL, 0x2a29); + /* Set AD10 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_ADC10_PDE_FLOAT_CTL, 0x2a00); + /* Set DMIC1/DMIC2 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_DMIC1_2_PDE_FLOAT_CTL, 0x2a2a); + /* Set DMIC2 IT entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_DMIC_ENT_FLOAT_CTL, 0x2626); + /* Set AD10 FU entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_ADC_ENT_FLOAT_CTL, 0x1e00); + /* Set DMIC2 FU entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_DMIC_GAIN_ENT_FLOAT_CTL0, 0x1515); + /* Set AD10 FU channel floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_ADC_VOL_CH_FLOAT_CTL, 0x0304); + /* Set DMIC2 FU channel floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_DMIC_GAIN_ENT_FLOAT_CTL2, 0x0304); + /* vf71f_r12_07_06 and vf71f_r13_07_06 = 2’b00 */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_HDA_LEGACY_CONFIG_CTL0, 0x0000); + /* Enable vf707_r12_05/vf707_r13_05 */ + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_IT26, + RT722_SDCA_CTL_VENDOR_DEF, 0), 0x01); + /* Fine tune PDE2A latency */ + regmap_write(rt722->regmap, 0x2f5c, 0x25); +} + +static void rt722_sdca_amp_preset(struct rt722_sdca_priv *rt722) +{ + /* Set DVQ=01 */ + rt722_sdca_index_write(rt722, RT722_VENDOR_REG, RT722_CLSD_CTRL6, + 0xc215); + /* Reset dc_cal_top */ + rt722_sdca_index_write(rt722, RT722_VENDOR_CALI, RT722_DC_CALIB_CTRL, + 0x702c); + /* W1C Trigger Calibration */ + rt722_sdca_index_write(rt722, RT722_VENDOR_CALI, RT722_DC_CALIB_CTRL, + 0xf02d); + /* Set DAC02/ClassD power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_AMP_PDE_FLOAT_CTL, + 0x2323); + /* Set EAPD high */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_EAPD_CTL, + 0x0002); + /* Enable vf707_r14 */ + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_OT23, + RT722_SDCA_CTL_VENDOR_DEF, CH_08), 0x04); +} + +static void rt722_sdca_jack_preset(struct rt722_sdca_priv *rt722) +{ + int loop_check, chk_cnt = 100, ret; + unsigned int calib_status = 0; + + /* Read eFuse */ + rt722_sdca_index_write(rt722, RT722_VENDOR_SPK_EFUSE, RT722_DC_CALIB_CTRL, + 0x4808); + /* Button A, B, C, D bypass mode */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_UMP_HID_CTL4, + 0xcf00); + /* HID1 slot enable */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_UMP_HID_CTL5, + 0x000f); + /* Report ID for HID1 */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_UMP_HID_CTL0, + 0x1100); + /* OSC/OOC for slot 2, 3 */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_UMP_HID_CTL7, + 0x0c12); + /* Set JD de-bounce clock control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_REG, RT722_JD_CTRL1, + 0x7002); + /* Set DVQ=01 */ + rt722_sdca_index_write(rt722, RT722_VENDOR_REG, RT722_CLSD_CTRL6, + 0xc215); + /* FSM switch to calibration manual mode */ + rt722_sdca_index_write(rt722, RT722_VENDOR_REG, RT722_FSM_CTL, + 0x4100); + /* W1C Trigger DC calibration (HP) */ + rt722_sdca_index_write(rt722, RT722_VENDOR_CALI, RT722_DAC_DC_CALI_CTL3, + 0x008d); + /* check HP calibration FSM status */ + for (loop_check = 0; loop_check < chk_cnt; loop_check++) { + ret = rt722_sdca_index_read(rt722, RT722_VENDOR_CALI, + RT722_DAC_DC_CALI_CTL3, &calib_status); + if (ret < 0 || loop_check == chk_cnt) + dev_dbg(&rt722->slave->dev, "calibration failed!, ret=%d\n", ret); + if ((calib_status & 0x0040) == 0x0) + break; + } + /* Release HP-JD, EN_CBJ_TIE_GL/R open, en_osw gating auto done bit */ + rt722_sdca_index_write(rt722, RT722_VENDOR_REG, RT722_DIGITAL_MISC_CTRL4, + 0x0010); + /* Set ADC09 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_ADC0A_08_PDE_FLOAT_CTL, + 0x2a12); + /* Set MIC2 and LINE1 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_MIC2_LINE2_PDE_FLOAT_CTL, + 0x3429); + /* Set ET41h and LINE2 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_ET41_LINE2_PDE_FLOAT_CTL, + 0x4112); + /* Set DAC03 and HP power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_DAC03_HP_PDE_FLOAT_CTL, + 0x4040); + /* Fine tune PDE40 latency */ + regmap_write(rt722->regmap, 0x2f58, 0x07); +} + +int rt722_sdca_io_init(struct device *dev, struct sdw_slave *slave) +{ + struct rt722_sdca_priv *rt722 = dev_get_drvdata(dev); + + rt722->disable_irq = false; + + if (rt722->hw_init) + return 0; + + if (rt722->first_hw_init) { + regcache_cache_only(rt722->regmap, false); + regcache_cache_bypass(rt722->regmap, true); + regcache_cache_only(rt722->mbq_regmap, false); + regcache_cache_bypass(rt722->mbq_regmap, true); + } else { + /* + * PM runtime is only enabled when a Slave reports as Attached + */ + + /* set autosuspend parameters */ + pm_runtime_set_autosuspend_delay(&slave->dev, 3000); + pm_runtime_use_autosuspend(&slave->dev); + + /* update count of parent 'active' children */ + pm_runtime_set_active(&slave->dev); + + /* make sure the device does not suspend immediately */ + pm_runtime_mark_last_busy(&slave->dev); + + pm_runtime_enable(&slave->dev); + } + + pm_runtime_get_noresume(&slave->dev); + + rt722_sdca_dmic_preset(rt722); + rt722_sdca_amp_preset(rt722); + rt722_sdca_jack_preset(rt722); + + if (rt722->first_hw_init) { + regcache_cache_bypass(rt722->regmap, false); + regcache_mark_dirty(rt722->regmap); + regcache_cache_bypass(rt722->mbq_regmap, false); + regcache_mark_dirty(rt722->mbq_regmap); + } else + rt722->first_hw_init = true; + + /* Mark Slave initialization complete */ + rt722->hw_init = true; + + pm_runtime_mark_last_busy(&slave->dev); + pm_runtime_put_autosuspend(&slave->dev); + + dev_dbg(&slave->dev, "%s hw_init complete\n", __func__); + return 0; +} + +MODULE_DESCRIPTION("ASoC RT722 SDCA SDW driver"); +MODULE_AUTHOR("Jack Yu <jack.yu(a)realtek.com>"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/rt722-sdca.h b/sound/soc/codecs/rt722-sdca.h new file mode 100644 index 000000000000..5bc6184d09aa --- /dev/null +++ b/sound/soc/codecs/rt722-sdca.h @@ -0,0 +1,238 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * rt722-sdca.h -- RT722 SDCA ALSA SoC audio driver header + * + * Copyright(c) 2023 Realtek Semiconductor Corp. + */ + +#ifndef __RT722_H__ +#define __RT722_H__ + +#include <linux/pm.h> +#include <linux/regmap.h> +#include <linux/soundwire/sdw.h> +#include <linux/soundwire/sdw_type.h> +#include <sound/soc.h> +#include <linux/workqueue.h> + +struct rt722_sdca_priv { + struct regmap *regmap; + struct regmap *mbq_regmap; + struct snd_soc_component *component; + struct sdw_slave *slave; + enum sdw_slave_status status; + struct sdw_bus_params params; + bool hw_init; + bool first_hw_init; + struct mutex calibrate_mutex; + struct mutex disable_irq_lock; + bool disable_irq; + /* For Headset jack & Headphone */ + unsigned int scp_sdca_stat1; + unsigned int scp_sdca_stat2; + struct snd_soc_jack *hs_jack; + struct delayed_work jack_detect_work; + struct delayed_work jack_btn_check_work; + int jack_type; + int jd_src; + bool fu0f_dapm_mute; + bool fu0f_mixer_l_mute; + bool fu0f_mixer_r_mute; + /* For DMIC */ + bool fu1e_dapm_mute; + bool fu1e_mixer_mute[4]; +}; + +struct rt722_sdca_dmic_kctrl_priv { + unsigned int reg_base; + unsigned int count; + unsigned int max; + unsigned int invert; +}; + +/* NID */ +#define RT722_VENDOR_REG 0x20 +#define RT722_VENDOR_CALI 0x58 +#define RT722_VENDOR_SPK_EFUSE 0x5c +#define RT722_VENDOR_IMS_DRE 0x5b +#define RT722_VENDOR_ANALOG_CTL 0x5f +#define RT722_VENDOR_HDA_CTL 0x61 + +/* Index (NID:20h) */ +#define RT722_JD_PRODUCT_NUM 0x00 +#define RT722_ANALOG_BIAS_CTL3 0x04 +#define RT722_JD_CTRL1 0x09 +#define RT722_LDO2_3_CTL1 0x0e +#define RT722_LDO1_CTL 0x1a +#define RT722_HP_JD_CTRL 0x24 +#define RT722_CLSD_CTRL6 0x3c +#define RT722_COMBO_JACK_AUTO_CTL1 0x45 +#define RT722_COMBO_JACK_AUTO_CTL2 0x46 +#define RT722_COMBO_JACK_AUTO_CTL3 0x47 +#define RT722_DIGITAL_MISC_CTRL4 0x4a +#define RT722_FSM_CTL 0x67 +#define RT722_SDCA_INTR_REC 0x82 +#define RT722_SW_CONFIG1 0x8a +#define RT722_SW_CONFIG2 0x8b + +/* Index (NID:58h) */ +#define RT722_DAC_DC_CALI_CTL0 0x00 +#define RT722_DAC_DC_CALI_CTL1 0x01 +#define RT722_DAC_DC_CALI_CTL2 0x02 +#define RT722_DAC_DC_CALI_CTL3 0x03 + +/* Index (NID:59h) */ +#define RT722_ULTRA_SOUND_DETECTOR6 0x1e + +/* Index (NID:5bh) */ +#define RT722_IMS_DIGITAL_CTL1 0x00 +#define RT722_IMS_DIGITAL_CTL5 0x05 +#define RT722_HP_DETECT_RLDET_CTL1 0x29 +#define RT722_HP_DETECT_RLDET_CTL2 0x2a + +/* Index (NID:5fh) */ +#define RT722_MISC_POWER_CTL0 0x00 +#define RT722_MISC_POWER_CTL7 0x08 + +/* Index (NID:61h) */ +#define RT722_HDA_LEGACY_MUX_CTL0 0x00 +#define RT722_HDA_LEGACY_UNSOL_CTL 0x03 +#define RT722_HDA_LEGACY_CONFIG_CTL0 0x06 +#define RT722_HDA_LEGACY_RESET_CTL 0x08 +#define RT722_HDA_LEGACY_GPIO_WAKE_EN_CTL 0x0e +#define RT722_DMIC_ENT_FLOAT_CTL 0x10 +#define RT722_DMIC_GAIN_ENT_FLOAT_CTL0 0x11 +#define RT722_DMIC_GAIN_ENT_FLOAT_CTL2 0x13 +#define RT722_ADC_ENT_FLOAT_CTL 0x15 +#define RT722_ADC_VOL_CH_FLOAT_CTL 0x17 +#define RT722_ADC_SAMPLE_RATE_FLOAT 0x18 +#define RT722_DAC03_HP_PDE_FLOAT_CTL 0x22 +#define RT722_MIC2_LINE2_PDE_FLOAT_CTL 0x23 +#define RT722_ET41_LINE2_PDE_FLOAT_CTL 0x24 +#define RT722_ADC0A_08_PDE_FLOAT_CTL 0x25 +#define RT722_ADC10_PDE_FLOAT_CTL 0x26 +#define RT722_DMIC1_2_PDE_FLOAT_CTL 0x28 +#define RT722_AMP_PDE_FLOAT_CTL 0x29 +#define RT722_I2S_IN_OUT_PDE_FLOAT_CTL 0x2f +#define RT722_GE_RELATED_CTL1 0x45 +#define RT722_GE_RELATED_CTL2 0x46 +#define RT722_MIXER_CTL0 0x52 +#define RT722_MIXER_CTL1 0x53 +#define RT722_EAPD_CTL 0x55 +#define RT722_UMP_HID_CTL0 0x60 +#define RT722_UMP_HID_CTL1 0x61 +#define RT722_UMP_HID_CTL2 0x62 +#define RT722_UMP_HID_CTL3 0x63 +#define RT722_UMP_HID_CTL4 0x64 +#define RT722_UMP_HID_CTL5 0x65 +#define RT722_UMP_HID_CTL6 0x66 +#define RT722_UMP_HID_CTL7 0x67 +#define RT722_UMP_HID_CTL8 0x68 + +/* Parameter & Verb control 01 (0x1a)(NID:20h) */ +#define RT722_HIDDEN_REG_SW_RESET (0x1 << 14) + +/* combo jack auto switch control 2 (0x46)(NID:20h) */ +#define RT722_COMBOJACK_AUTO_DET_STATUS (0x1 << 11) +#define RT722_COMBOJACK_AUTO_DET_TRS (0x1 << 10) +#define RT722_COMBOJACK_AUTO_DET_CTIA (0x1 << 9) +#define RT722_COMBOJACK_AUTO_DET_OMTP (0x1 << 8) + +/* DAC calibration control (0x00)(NID:58h) */ +#define RT722_DC_CALIB_CTRL (0x1 << 16) +/* DAC DC offset calibration control-1 (0x01)(NID:58h) */ +#define RT722_PDM_DC_CALIB_STATUS (0x1 << 15) + +#define RT722_EAPD_HIGH 0x2 +#define RT722_EAPD_LOW 0x0 + +/* Buffer address for HID */ +#define RT722_BUF_ADDR_HID1 0x44030000 +#define RT722_BUF_ADDR_HID2 0x44030020 + +/* RT722 SDCA Control - function number */ +#define FUNC_NUM_JACK_CODEC 0x01 +#define FUNC_NUM_MIC_ARRAY 0x02 +#define FUNC_NUM_HID 0x03 +#define FUNC_NUM_AMP 0x04 + +/* RT722 SDCA entity */ +#define RT722_SDCA_ENT_HID01 0x01 +#define RT722_SDCA_ENT_GE49 0x49 +#define RT722_SDCA_ENT_USER_FU05 0x05 +#define RT722_SDCA_ENT_USER_FU06 0x06 +#define RT722_SDCA_ENT_USER_FU0F 0x0f +#define RT722_SDCA_ENT_USER_FU10 0x19 +#define RT722_SDCA_ENT_USER_FU1E 0x1e +#define RT722_SDCA_ENT_FU15 0x15 +#define RT722_SDCA_ENT_PDE23 0x23 +#define RT722_SDCA_ENT_PDE40 0x40 +#define RT722_SDCA_ENT_PDE11 0x11 +#define RT722_SDCA_ENT_PDE12 0x12 +#define RT722_SDCA_ENT_PDE2A 0x2a +#define RT722_SDCA_ENT_CS01 0x01 +#define RT722_SDCA_ENT_CS11 0x11 +#define RT722_SDCA_ENT_CS1F 0x1f +#define RT722_SDCA_ENT_CS1C 0x1c +#define RT722_SDCA_ENT_CS31 0x31 +#define RT722_SDCA_ENT_OT23 0x42 +#define RT722_SDCA_ENT_IT26 0x26 +#define RT722_SDCA_ENT_IT09 0x09 +#define RT722_SDCA_ENT_PLATFORM_FU15 0x15 +#define RT722_SDCA_ENT_PLATFORM_FU44 0x44 +#define RT722_SDCA_ENT_XU03 0x03 +#define RT722_SDCA_ENT_XU0D 0x0d + +/* RT722 SDCA control */ +#define RT722_SDCA_CTL_SAMPLE_FREQ_INDEX 0x10 +#define RT722_SDCA_CTL_FU_MUTE 0x01 +#define RT722_SDCA_CTL_FU_VOLUME 0x02 +#define RT722_SDCA_CTL_HIDTX_CURRENT_OWNER 0x10 +#define RT722_SDCA_CTL_HIDTX_SET_OWNER_TO_DEVICE 0x11 +#define RT722_SDCA_CTL_HIDTX_MESSAGE_OFFSET 0x12 +#define RT722_SDCA_CTL_HIDTX_MESSAGE_LENGTH 0x13 +#define RT722_SDCA_CTL_SELECTED_MODE 0x01 +#define RT722_SDCA_CTL_DETECTED_MODE 0x02 +#define RT722_SDCA_CTL_REQ_POWER_STATE 0x01 +#define RT722_SDCA_CTL_VENDOR_DEF 0x30 +#define RT722_SDCA_CTL_FU_CH_GAIN 0x0b + +/* RT722 SDCA channel */ +#define CH_L 0x01 +#define CH_R 0x02 +#define CH_01 0x01 +#define CH_02 0x02 +#define CH_03 0x03 +#define CH_04 0x04 +#define CH_08 0x08 + +/* sample frequency index */ +#define RT722_SDCA_RATE_16000HZ 0x04 +#define RT722_SDCA_RATE_32000HZ 0x07 +#define RT722_SDCA_RATE_44100HZ 0x08 +#define RT722_SDCA_RATE_48000HZ 0x09 +#define RT722_SDCA_RATE_96000HZ 0x0b +#define RT722_SDCA_RATE_192000HZ 0x0d + +enum { + RT722_AIF1, /* For headset mic and headphone */ + RT722_AIF2, /* For speaker */ + RT722_AIF3, /* For dmic */ + RT722_AIFS, +}; + +enum rt722_sdca_jd_src { + RT722_JD_NULL, + RT722_JD1, +}; + +int rt722_sdca_io_init(struct device *dev, struct sdw_slave *slave); +int rt722_sdca_init(struct device *dev, struct regmap *regmap, + struct regmap *mbq_regmap, struct sdw_slave *slave); +int rt722_sdca_index_write(struct rt722_sdca_priv *rt722, + unsigned int nid, unsigned int reg, unsigned int value); +int rt722_sdca_index_read(struct rt722_sdca_priv *rt722, + unsigned int nid, unsigned int reg, unsigned int *value); + +int rt722_sdca_jack_detect(struct rt722_sdca_priv *rt722, bool *hp, bool *mic); +#endif /* __RT722_H__ */ -- 2.40.0

2 1

[PATCH] ASoC: SOF: amd: Fix NULL pointer crash in acp_sof_ipc_msg_data function
by V sujith kumar Reddy 09 May '23

09 May '23

Check substream and runtime variables before assigning. Signed-off-by: V sujith kumar Reddy <Vsujithkumar.Reddy(a)amd.com> --- sound/soc/sof/amd/acp-ipc.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/sound/soc/sof/amd/acp-ipc.c b/sound/soc/sof/amd/acp-ipc.c index 4e0c48a36159..749e856dc601 100644 --- a/sound/soc/sof/amd/acp-ipc.c +++ b/sound/soc/sof/amd/acp-ipc.c @@ -209,7 +209,12 @@ int acp_sof_ipc_msg_data(struct snd_sof_dev *sdev, struct snd_sof_pcm_stream *sp acp_mailbox_read(sdev, offset, p, sz); } else { struct snd_pcm_substream *substream = sps->substream; - struct acp_dsp_stream *stream = substream->runtime->private_data; + struct acp_dsp_stream *stream; + + if (!substream || !substream->runtime) + return -ESTRPIPE; + + stream = substream->runtime->private_data; if (!stream) return -ESTRPIPE; -- 2.25.1

2 1

[PATCH] ASoC:codecs: lpass: Fix for KASAN use_after_free out of bounds
by Ravulapati Vishnu Vardhan Rao 09 May '23

09 May '23

When we run syzkaller we get below Out of Bounds error. "KASAN: slab-out-of-bounds Read in regcache_flat_read" Below is the backtrace of the issue: BUG: KASAN: slab-out-of-bounds in regcache_flat_read+0x10c/0x110 Read of size 4 at addr ffffff8088fbf714 by task syz-executor.4/14144 CPU: 6 PID: 14144 Comm: syz-executor.4 Tainted: G W Hardware name: Qualcomm Technologies, Inc. sc7280 CRD platform (rev5+) (DT) Call trace: dump_backtrace+0x0/0x4ec show_stack+0x34/0x50 dump_stack_lvl+0xdc/0x11c print_address_description+0x30/0x2d8 kasan_report+0x178/0x1e4 __asan_report_load4_noabort+0x44/0x50 regcache_flat_read+0x10c/0x110 regcache_read+0xf8/0x5a0 _regmap_read+0x45c/0x86c _regmap_update_bits+0x128/0x290 regmap_update_bits_base+0xc0/0x15c snd_soc_component_update_bits+0xa8/0x22c snd_soc_component_write_field+0x68/0xd4 tx_macro_put_dec_enum+0x1d0/0x268 snd_ctl_elem_write+0x288/0x474 By Error checking and checking valid values issue gets rectifies. Signed-off-by: Ravulapati Vishnu Vardhan Rao <quic_visr(a)quicinc.com> --- sound/soc/codecs/lpass-tx-macro.c | 23 ++++++++++++++++++----- 1 file changed, 18 insertions(+), 5 deletions(-) diff --git a/sound/soc/codecs/lpass-tx-macro.c b/sound/soc/codecs/lpass-tx-macro.c index da6fcf7f0991..6575b0bb6a47 100644 --- a/sound/soc/codecs/lpass-tx-macro.c +++ b/sound/soc/codecs/lpass-tx-macro.c @@ -746,6 +746,10 @@ static int tx_macro_put_dec_enum(struct snd_kcontrol *kcontrol, struct tx_macro *tx = snd_soc_component_get_drvdata(component); val = ucontrol->value.enumerated.item[0]; + if (val < 0 && val > 15) { + dev_err(component->dev, "Wrong value for DMIC configuration"); + return -EINVAL; + } switch (e->reg) { case CDC_TX_INP_MUX_ADC_MUX0_CFG0: @@ -772,6 +776,9 @@ static int tx_macro_put_dec_enum(struct snd_kcontrol *kcontrol, case CDC_TX_INP_MUX_ADC_MUX7_CFG0: mic_sel_reg = CDC_TX7_TX_PATH_CFG0; break; + default: + dev_err(component->dev, "Error in configuration!!\n"); + return -EINVAL; } if (val != 0) { @@ -785,13 +792,19 @@ static int tx_macro_put_dec_enum(struct snd_kcontrol *kcontrol, snd_soc_component_write_field(component, mic_sel_reg, CDC_TXn_ADC_DMIC_SEL_MASK, 1); dmic = TX_ADC_TO_DMIC(val); - dmic_clk_reg = CDC_TX_TOP_CSR_SWR_DMICn_CTL(dmic); - snd_soc_component_write_field(component, dmic_clk_reg, - CDC_TX_SWR_DMIC_CLK_SEL_MASK, - tx->dmic_clk_div); + if (dmic < 4) { + dmic_clk_reg = CDC_TX_TOP_CSR_SWR_DMICn_CTL(dmic); + snd_soc_component_write_field(component, dmic_clk_reg, + CDC_TX_SWR_DMIC_CLK_SEL_MASK, + tx->dmic_clk_div); + } else { + dev_err(component->dev, "dmic for clk sel is wrong, + expected less than 4 but received %d\n", dmic); + return -EINVAL; + } + } } - return snd_soc_dapm_put_enum_double(kcontrol, ucontrol); } -- 2.17.1

3 3

[PATCH] ASoC: dt-bindings: nau8825: Convert to dtschema
by David Lin 09 May '23

09 May '23

Convert the NAU8825 audio CODEC bindings to DT schema. Signed-off-by: David Lin <CTLIN0(a)nuvoton.com> --- .../devicetree/bindings/sound/nau8825.txt | 111 --------- .../bindings/sound/nuvoton,nau8825.yaml | 220 ++++++++++++++++++ 2 files changed, 220 insertions(+), 111 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sound/nau8825.txt create mode 100644 Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml diff --git a/Documentation/devicetree/bindings/sound/nau8825.txt b/Documentation/devicetree/bindings/sound/nau8825.txt deleted file mode 100644 index a9c34526f4cb..000000000000 --- a/Documentation/devicetree/bindings/sound/nau8825.txt +++ /dev/null @@ -1,111 +0,0 @@ -Nuvoton NAU8825 audio codec - -This device supports I2C only. - -Required properties: - - compatible : Must be "nuvoton,nau8825" - - - reg : the I2C address of the device. This is either 0x1a (CSB=0) or 0x1b (CSB=1). - -Optional properties: - - nuvoton,jkdet-enable: Enable jack detection via JKDET pin. - - nuvoton,jkdet-pull-enable: Enable JKDET pin pull. If set - pin pull enabled, - otherwise pin in high impedance state. - - nuvoton,jkdet-pull-up: Pull-up JKDET pin. If set then JKDET pin is pull up, otherwise pull down. - - nuvoton,jkdet-polarity: JKDET pin polarity. 0 - active high, 1 - active low. - - - nuvoton,vref-impedance: VREF Impedance selection - 0 - Open - 1 - 25 kOhm - 2 - 125 kOhm - 3 - 2.5 kOhm - - - nuvoton,micbias-voltage: Micbias voltage level. - 0 - VDDA - 1 - VDDA - 2 - VDDA * 1.1 - 3 - VDDA * 1.2 - 4 - VDDA * 1.3 - 5 - VDDA * 1.4 - 6 - VDDA * 1.53 - 7 - VDDA * 1.53 - - - nuvoton,sar-threshold-num: Number of buttons supported - - nuvoton,sar-threshold: Impedance threshold for each button. Array that contains up to 8 buttons configuration. SAR value is calculated as - SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R) - where MICBIAS is configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by 'nuvoton,sar-voltage', R - button impedance. - Refer datasheet section 10.2 for more information about threshold calculation. - - - nuvoton,sar-hysteresis: Button impedance measurement hysteresis. - - - nuvoton,sar-voltage: Reference voltage for button impedance measurement. - 0 - VDDA - 1 - VDDA - 2 - VDDA * 1.1 - 3 - VDDA * 1.2 - 4 - VDDA * 1.3 - 5 - VDDA * 1.4 - 6 - VDDA * 1.53 - 7 - VDDA * 1.53 - - - nuvoton,sar-compare-time: SAR compare time - 0 - 500 ns - 1 - 1 us - 2 - 2 us - 3 - 4 us - - - nuvoton,sar-sampling-time: SAR sampling time - 0 - 2 us - 1 - 4 us - 2 - 8 us - 3 - 16 us - - - nuvoton,short-key-debounce: Button short key press debounce time. - 0 - 30 ms - 1 - 50 ms - 2 - 100 ms - 3 - 30 ms - - - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms - - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms - - - nuvoton,crosstalk-enable: make crosstalk function enable if set. - - - nuvoton,adcout-drive-strong: make the drive strength of ADCOUT IO PIN strong if set. - Otherwise, the drive keeps normal strength. - - - nuvoton,adc-delay-ms: Delay (in ms) to make input path stable and avoid pop noise. The - default value is 125 and range between 125 to 500 ms. - - - clocks: list of phandle and clock specifier pairs according to common clock bindings for the - clocks described in clock-names - - clock-names: should include "mclk" for the MCLK master clock - -Example: - - headset: nau8825@1a { - compatible = "nuvoton,nau8825"; - reg = <0x1a>; - interrupt-parent = <&gpio>; - interrupts = <TEGRA_GPIO(E, 6) IRQ_TYPE_LEVEL_LOW>; - nuvoton,jkdet-enable; - nuvoton,jkdet-pull-enable; - nuvoton,jkdet-pull-up; - nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>; - nuvoton,vref-impedance = <2>; - nuvoton,micbias-voltage = <6>; - // Setup 4 buttons impedance according to Android specification - nuvoton,sar-threshold-num = <4>; - nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>; - nuvoton,sar-hysteresis = <1>; - nuvoton,sar-voltage = <0>; - nuvoton,sar-compare-time = <0>; - nuvoton,sar-sampling-time = <0>; - nuvoton,short-key-debounce = <2>; - nuvoton,jack-insert-debounce = <7>; - nuvoton,jack-eject-debounce = <7>; - nuvoton,crosstalk-enable; - - clock-names = "mclk"; - clocks = <&tegra_pmc TEGRA_PMC_CLK_OUT_2>; - }; diff --git a/Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml b/Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml new file mode 100644 index 000000000000..7938bf6d9190 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml @@ -0,0 +1,220 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/nuvoton,nau8825.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NAU8825 audio CODEC + +maintainers: + - John Hsu <KCHSU0(a)nuvoton.com> + +allOf: + - $ref: dai-common.yaml# + +properties: + compatible: + enum: + - nuvoton,nau8825 + + reg: + maxItems: 1 + + nuvoton,jkdet-enable: + description: + Enable jack detection via JKDET pin. + type: boolean + + nuvoton,jkdet-pull-enable: + description: + Enable JKDET pin pull. + If set - pin pull enabled, otherwise pin in high impedance state. + type: boolean + + nuvoton,jkdet-pull-up: + description: + Pull-up JKDET pin. + If set then JKDET pin is pull up, otherwise pull down. + type: boolean + + nuvoton,jkdet-polarity: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + JKDET pin polarity. + enum: + - 0 # active high + - 1 # active low + + nuvoton,vref-impedance: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + VREF Impedance selection. + enum: + - 0 # Open + - 1 # 25 kOhm + - 2 # 125 kOhm + - 3 # 2.5 kOhm + + nuvoton,micbias-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Micbias voltage level. + enum: + - 0 # VDDA + - 1 # VDDA + - 2 # VDDA * 1.1 + - 3 # VDDA * 1.2 + - 4 # VDDA * 1.3 + - 5 # VDDA * 1.4 + - 6 # VDDA * 1.53 + - 7 # VDDA * 1.53 + + nuvoton,sar-threshold-num: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Number of buttons supported. + minimum: 1 + maximum: 4 + + nuvoton,sar-threshold: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + Impedance threshold for each button. Array that contains up to 8 buttons + configuration. SAR value is calculated as + SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R) where MICBIAS is + configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by + 'nuvoton,sar-voltage', R - button impedance. + Refer datasheet section 10.2 for more information about threshold + calculation. + minItems: 1 + maxItems: 4 + items: + minimum: 0 + maximum: 255 + + nuvoton,sar-hysteresis: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Button impedance measurement hysteresis. + + nuvoton,sar-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Reference voltage for button impedance measurement. + enum: + - 0 # VDDA + - 1 # VDDA + - 2 # VDDA * 1.1 + - 3 # VDDA * 1.2 + - 4 # VDDA * 1.3 + - 5 # VDDA * 1.4 + - 6 # VDDA * 1.53 + - 7 # VDDA * 1.53 + + nuvoton,sar-compare-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + SAR compare time. + enum: + - 0 # 500ns + - 1 # 1us + - 2 # 2us + - 3 # 4us + + nuvoton,sar-sampling-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + SAR sampling time. + enum: + - 0 # 2us + - 1 # 4us + - 2 # 8us + - 3 # 16us + + nuvoton,short-key-debounce: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Button short key press debounce time. + enum: + - 0 # 30 ms + - 1 # 50 ms + - 2 # 100 ms + + nuvoton,jack-insert-debounce: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + number from 0 to 7 that sets debounce time to 2^(n+2) ms. + + nuvoton,jack-eject-debounce: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + number from 0 to 7 that sets debounce time to 2^(n+2) ms + + nuvoton,crosstalk-enable: + description: + make crosstalk function enable if set. + type: boolean + + nuvoton,adcout-drive-strong: + description: + make the drive strength of ADCOUT IO PIN strong if set. + Otherwise, the drive keeps normal strength. + type: boolean + + nuvoton,adc-delay-ms: + description: + Delay (in ms) to make input path stable and avoid pop noise. + The default value is 125 and range between 125 to 500 ms. + minimum: 125 + maximum: 500 + + clocks: + description: + list of phandle and clock specifier pairs according to common clock + bindings for the clocks described in clock-names. + + clock-names: + description: + should include "mclk" for the MCLK master clock. + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/tegra-gpio.h> + #include <dt-bindings/soc/tegra-pmc.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + headset: nau8825@1a { + compatible = "nuvoton,nau8825"; + reg = <0x1a>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(E, 6) IRQ_TYPE_LEVEL_LOW>; + nuvoton,jkdet-enable; + nuvoton,jkdet-pull-enable; + nuvoton,jkdet-pull-up; + nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>; + nuvoton,vref-impedance = <2>; + nuvoton,micbias-voltage = <6>; + // Setup 4 buttons impedance according to Android specification + nuvoton,sar-threshold-num = <4>; + nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>; + nuvoton,sar-hysteresis = <1>; + nuvoton,sar-voltage = <0>; + nuvoton,sar-compare-time = <0>; + nuvoton,sar-sampling-time = <0>; + nuvoton,short-key-debounce = <2>; + nuvoton,jack-insert-debounce = <7>; + nuvoton,jack-eject-debounce = <7>; + nuvoton,crosstalk-enable; + + clock-names = "mclk"; + clocks = <&tegra_pmc TEGRA_PMC_CLK_OUT_2>; + }; + }; -- 2.25.1

3 3

Fwd: Asus ROG Zephyrus GX701L sound problem
by Bagas Sanjaya 09 May '23

09 May '23

Hi, I notice a year-old bug report on bugzilla [1]. As many developers don't take a look on it, I decided to forward it by email. You will need to log in to bugzilla in order to contact the reporter. Quoting from the bug report: > Hello, > > I must mention right at the beginning that I tried all the solutions I found on the forums, but without success. > > The problem exists only with the speakers on the laptop, the microphone works, as do the headphones. > > I extracted the audio dump from windows and compared it with the dump from Linux and thus created this pinfcg below. > > Please, can someone add a kernel fix for ROG Zephyrus S17 GX701LWS_GX701LWS, Subsystem Id: 0x10431f01? > > ``` > > [codec] > > 0x10ec0294 0x10431f01 0 > > [pincfg] > > 0x19 0x03A11050 > > 0x1a 0x03A11C30 > > ``` > > This is what a quirk should look like: > > +SND_PCI_QUIRK(0x1043, 0x1f01, “ASUS GX701L”, ALC294_FIXUP_ASUS_SPK) > > [ 2.396344] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC294: line_outs=1 (0x17/0x0/0x0/0x0/0x0) type:speaker > [ 2.396348] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) > [ 2.396349] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0) > [ 2.396350] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0 > [ 2.396351] snd_hda_codec_realtek hdaudioC0D0: inputs: > [ 2.396352] snd_hda_codec_realtek hdaudioC0D0: Headset Mic=0x19 > [ 2.396353] snd_hda_codec_realtek hdaudioC0D0: Internal Mic=0x12 > > > > > hwinfo --sound  :heavy_check_mark: > 22: PCI 1f.3: 0403 Audio device > [Created at pci.386] > Unique ID: nS1_.Qb7ky1jjQRD > SysFS ID: /devices/pci0000:00/0000:00:1f.3 > SysFS BusID: 0000:00:1f.3 > Hardware Class: sound > Model: “Intel Comet Lake PCH cAVS” > Vendor: pci 0x8086 “Intel Corporation” > Device: pci 0x06c8 “Comet Lake PCH cAVS” > SubVendor: pci 0x1043 “ASUSTeK Computer Inc.” > SubDevice: pci 0x1f01 > Driver: “snd_hda_intel” > Driver Modules: “snd_hda_intel” > Memory Range: 0x94300000-0x94303fff (rw,non-prefetchable) > Memory Range: 0x94100000-0x941fffff (rw,non-prefetchable) > IRQ: 157 (817 events) > Module Alias: “pci:v00008086d000006C8sv00001043sd00001F01bc04sc03i80” > Driver Info #0: > Driver Status: snd_hda_intel is active > Driver Activation Cmd: “modprobe snd_hda_intel” > Driver Info #1: > Driver Status: snd_soc_skl is active > Driver Activation Cmd: “modprobe snd_soc_skl” > Driver Info #2: > Driver Status: snd_sof_pci_intel_cnl is active > Driver Activation Cmd: “modprobe snd_sof_pci_intel_cnl” > Config Status: cfg=new, avail=yes, need=no, active=unknown > > 29: PCI 100.1: 0403 Audio device > [Created at pci.386] > Unique ID: NXNs.SkelvpPm387 > Parent ID: vSkL.ZFPYIgTFUyC > SysFS ID: /devices/pci0000:00/0000:00:01.0/0000:01:00.1 > SysFS BusID: 0000:01:00.1 > Hardware Class: sound > Model: “nVidia TU104 HD Audio Controller” > Vendor: pci 0x10de “nVidia Corporation” > Device: pci 0x10f8 “TU104 HD Audio Controller” > SubVendor: pci 0x1043 “ASUSTeK Computer Inc.” > SubDevice: pci 0x186f > Revision: 0xa1 > Driver: “snd_hda_intel” > Driver Modules: “snd_hda_intel” > Memory Range: 0x94080000-0x94083fff (rw,non-prefetchable) > IRQ: 17 (1698 events) > Module Alias: “pci:v000010DEd000010F8sv00001043sd0000186Fbc04sc03i00” > Driver Info #0: > Driver Status: snd_hda_intel is active > Driver Activation Cmd: “modprobe snd_hda_intel” > Config Status: cfg=new, avail=yes, need=no, active=unknown > Attached to: #13 (PCI bridge) > > > If you need any more data, or smth just say so. To the reporter: It seems like the hardware problem, right? If so, can you test on different laptop? Thanks. [1]: https://bugzilla.kernel.org/show_bug.cgi?id=216392 -- An old man doll... just what I always wanted! - Clara

2 1

[PATCH v2] ASoC: dt-bindings: nau8540: Convert to dtschema
by Anup Sharma 09 May '23

09 May '23

Convert the NAU8540 audio CODEC bindings to DT schema Signed-off-by: Anup Sharma <anupnewsmail(a)gmail.com> Changes: V1 -> V2: Adhere to the correct procedure by including the maintainer's name. Drop Mark from maintainer. --- .../devicetree/bindings/sound/nau8540.txt | 16 -------- .../bindings/sound/nuvoton,nau8540.yaml | 40 +++++++++++++++++++ 2 files changed, 40 insertions(+), 16 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sound/nau8540.txt create mode 100644 Documentation/devicetree/bindings/sound/nuvoton,nau8540.yaml diff --git a/Documentation/devicetree/bindings/sound/nau8540.txt b/Documentation/devicetree/bindings/sound/nau8540.txt deleted file mode 100644 index 307a76528320..000000000000 --- a/Documentation/devicetree/bindings/sound/nau8540.txt +++ /dev/null @@ -1,16 +0,0 @@ -NAU85L40 audio CODEC - -This device supports I2C only. - -Required properties: - - - compatible : "nuvoton,nau8540" - - - reg : the I2C address of the device. - -Example: - -codec: nau8540@1c { - compatible = "nuvoton,nau8540"; - reg = <0x1c>; -}; diff --git a/Documentation/devicetree/bindings/sound/nuvoton,nau8540.yaml b/Documentation/devicetree/bindings/sound/nuvoton,nau8540.yaml new file mode 100644 index 000000000000..7ccfbb8d8b04 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nuvoton,nau8540.yaml @@ -0,0 +1,40 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/nuvoton,nau8540.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Nuvoton Technology Corporation NAU85L40 Audio CODEC + +maintainers: + - John Hsu <KCHSU0(a)nuvoton.com> + +allOf: + - $ref: dai-common.yaml# + +properties: + compatible: + const: nuvoton,nau8540 + + reg: + maxItems: 1 + + "#sound-dai-cells": + const: 0 + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + codec@1c { + compatible = "nuvoton,nau8540"; + reg = <0x1c>; + }; + }; -- 2.34.1

2 1

[PATCH] ASoC: dt-bindings: google,sc7180-trogdor: allow up to four codec DAIs
by Krzysztof Kozlowski 09 May '23

09 May '23

SC7180 Trogdor sound cards come with multiple audio amplifiers, so allow up to four of them to fix dtbs_check warnings like: sc7180-trogdor-homestar-r3.dtb: sound: dai-link@1:codec:sound-dai: [[275], [276], [277], [278]] is too long Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski(a)linaro.org> --- .../devicetree/bindings/sound/google,sc7180-trogdor.yaml | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/Documentation/devicetree/bindings/sound/google,sc7180-trogdor.yaml b/Documentation/devicetree/bindings/sound/google,sc7180-trogdor.yaml index 67ccddd44489..666a95ac22c8 100644 --- a/Documentation/devicetree/bindings/sound/google,sc7180-trogdor.yaml +++ b/Documentation/devicetree/bindings/sound/google,sc7180-trogdor.yaml @@ -74,7 +74,8 @@ patternProperties: properties: sound-dai: - maxItems: 1 + minItems: 1 + maxItems: 4 required: - link-name -- 2.34.1

3 2

[PATCH 1/1] ASoC: dwc: extend supported formats
by Maxim Kochetkov 09 May '23

09 May '23

The COMP1_TX_WORDSIZE_0/COMP2_RX_WORDSIZE_0 fields in the comp registers indicate the maximum wordsize supported. DWC I2S controller can operate with any smaller wordsize. So extend the formats to let I2S to operate in any allowed modes. Signed-off-by: Maxim Kochetkov <fido_max(a)inbox.ru> --- sound/soc/dwc/dwc-i2s.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/sound/soc/dwc/dwc-i2s.c b/sound/soc/dwc/dwc-i2s.c index acdf98b2ee9c..1f782752ea0b 100644 --- a/sound/soc/dwc/dwc-i2s.c +++ b/sound/soc/dwc/dwc-i2s.c @@ -480,9 +480,9 @@ static const u32 bus_widths[COMP_MAX_DATA_WIDTH] = { static const u32 formats[COMP_MAX_WORDSIZE] = { SNDRV_PCM_FMTBIT_S16_LE, SNDRV_PCM_FMTBIT_S16_LE, - SNDRV_PCM_FMTBIT_S24_LE, - SNDRV_PCM_FMTBIT_S24_LE, - SNDRV_PCM_FMTBIT_S32_LE, + SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S24_LE, + SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S24_LE, + SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S32_LE, 0, 0, 0 -- 2.39.2

2 1

[PATCH -next] ASoC: codecs: wcd938x: Remove unneeded semicolon
by Yang Li 09 May '23

09 May '23

./sound/soc/codecs/wcd938x-sdw.c:1274:2-3: Unneeded semicolon Reported-by: Abaci Robot <abaci(a)linux.alibaba.com> Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=4862 Signed-off-by: Yang Li <yang.lee(a)linux.alibaba.com> --- sound/soc/codecs/wcd938x-sdw.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/codecs/wcd938x-sdw.c b/sound/soc/codecs/wcd938x-sdw.c index 402286dfaea4..5befae414636 100644 --- a/sound/soc/codecs/wcd938x-sdw.c +++ b/sound/soc/codecs/wcd938x-sdw.c @@ -1271,7 +1271,7 @@ static int wcd9380_probe(struct sdw_slave *pdev, /* Start in cache-only until device is enumerated */ regcache_cache_only(wcd->regmap, true); - }; + } pm_runtime_set_autosuspend_delay(dev, 3000); pm_runtime_use_autosuspend(dev); -- 2.20.1.7.g153144c

2 1

[PATCH] ASoC: fsl_sai: MCLK bind with TX/RX enable bit
by Shengjiu Wang 09 May '23

09 May '23

On i.MX8MP, the sai MCLK is bound with TX/RX enable bit, which means the TX/RE enable bit need to be enabled then MCLK can be output on PAD. Some codec (for example: WM8962) needs the MCLK output earlier, otherwise there will be issue for codec configuration. Add new soc data "mclk_with_tere" for this platform and enable the MCLK output in startup stage. As "mclk_with_tere" only applied to i.MX8MP, currently The soc data is shared with i.MX8MN, so need to add an i.MX8MN own soc data with "mclk_with_tere" disabled. Signed-off-by: Shengjiu Wang <shengjiu.wang(a)nxp.com> --- sound/soc/fsl/fsl_sai.c | 24 +++++++++++++++++++++--- sound/soc/fsl/fsl_sai.h | 2 ++ 2 files changed, 23 insertions(+), 3 deletions(-) diff --git a/sound/soc/fsl/fsl_sai.c b/sound/soc/fsl/fsl_sai.c index abdaffb00fbd..d9344025dc16 100644 --- a/sound/soc/fsl/fsl_sai.c +++ b/sound/soc/fsl/fsl_sai.c @@ -1400,7 +1400,9 @@ static int fsl_sai_probe(struct platform_device *pdev) sai->cpu_dai_drv.symmetric_sample_bits = 0; } - if (of_property_read_bool(np, "fsl,sai-mclk-direction-output") && + sai->mclk_direction_output = of_property_read_bool(np, "fsl,sai-mclk-direction-output"); + + if (sai->mclk_direction_output && of_device_is_compatible(np, "fsl,imx6ul-sai")) { gpr = syscon_regmap_lookup_by_compatible("fsl,imx6ul-iomuxc-gpr"); if (IS_ERR(gpr)) { @@ -1443,7 +1445,7 @@ static int fsl_sai_probe(struct platform_device *pdev) dev_warn(dev, "Error reading SAI version: %d\n", ret); /* Select MCLK direction */ - if (of_property_read_bool(np, "fsl,sai-mclk-direction-output") && + if (sai->mclk_direction_output && sai->soc_data->max_register >= FSL_SAI_MCTL) { regmap_update_bits(sai->regmap, FSL_SAI_MCTL, FSL_SAI_MCTL_MCLK_EN, FSL_SAI_MCTL_MCLK_EN); @@ -1562,6 +1564,17 @@ static const struct fsl_sai_soc_data fsl_sai_imx8mm_data = { .max_register = FSL_SAI_MCTL, }; +static const struct fsl_sai_soc_data fsl_sai_imx8mn_data = { + .use_imx_pcm = true, + .use_edma = false, + .fifo_depth = 128, + .reg_offset = 8, + .mclk0_is_mclk1 = false, + .pins = 8, + .flags = 0, + .max_register = FSL_SAI_MDIV, +}; + static const struct fsl_sai_soc_data fsl_sai_imx8mp_data = { .use_imx_pcm = true, .use_edma = false, @@ -1571,6 +1584,7 @@ static const struct fsl_sai_soc_data fsl_sai_imx8mp_data = { .pins = 8, .flags = 0, .max_register = FSL_SAI_MDIV, + .mclk_with_tere = true, }; static const struct fsl_sai_soc_data fsl_sai_imx8ulp_data = { @@ -1606,7 +1620,7 @@ static const struct of_device_id fsl_sai_ids[] = { { .compatible = "fsl,imx8mm-sai", .data = &fsl_sai_imx8mm_data }, { .compatible = "fsl,imx8mp-sai", .data = &fsl_sai_imx8mp_data }, { .compatible = "fsl,imx8ulp-sai", .data = &fsl_sai_imx8ulp_data }, - { .compatible = "fsl,imx8mn-sai", .data = &fsl_sai_imx8mp_data }, + { .compatible = "fsl,imx8mn-sai", .data = &fsl_sai_imx8mn_data }, { .compatible = "fsl,imx93-sai", .data = &fsl_sai_imx93_data }, { /* sentinel */ } }; @@ -1671,6 +1685,10 @@ static int fsl_sai_runtime_resume(struct device *dev) if (ret) goto disable_rx_clk; + if (sai->soc_data->mclk_with_tere && sai->mclk_direction_output) + regmap_update_bits(sai->regmap, FSL_SAI_TCSR(ofs), + FSL_SAI_CSR_TERE, FSL_SAI_CSR_TERE); + return 0; disable_rx_clk: diff --git a/sound/soc/fsl/fsl_sai.h b/sound/soc/fsl/fsl_sai.h index 197748a888d5..3eb994aef36a 100644 --- a/sound/soc/fsl/fsl_sai.h +++ b/sound/soc/fsl/fsl_sai.h @@ -230,6 +230,7 @@ struct fsl_sai_soc_data { bool use_imx_pcm; bool use_edma; bool mclk0_is_mclk1; + bool mclk_with_tere; unsigned int fifo_depth; unsigned int pins; unsigned int reg_offset; @@ -287,6 +288,7 @@ struct fsl_sai { bool synchronous[2]; struct fsl_sai_dl_cfg *dl_cfg; unsigned int dl_cfg_cnt; + bool mclk_direction_output; unsigned int mclk_id[2]; unsigned int mclk_streams; -- 2.34.1

2 1

[PATCH v2 1/2] ASoC: dwc: add optional reset support
by Maxim Kochetkov 09 May '23

09 May '23

Some SoC may have resets for I2S subsystem. So add optional reset support. Signed-off-by: Maxim Kochetkov <fido_max(a)inbox.ru> --- sound/soc/dwc/dwc-i2s.c | 27 +++++++++++++++++++++------ sound/soc/dwc/local.h | 1 + 2 files changed, 22 insertions(+), 6 deletions(-) diff --git a/sound/soc/dwc/dwc-i2s.c b/sound/soc/dwc/dwc-i2s.c index acdf98b2ee9c..e2b2ba014a2e 100644 --- a/sound/soc/dwc/dwc-i2s.c +++ b/sound/soc/dwc/dwc-i2s.c @@ -17,6 +17,7 @@ #include <linux/io.h> #include <linux/interrupt.h> #include <linux/module.h> +#include <linux/reset.h> #include <linux/slab.h> #include <linux/pm_runtime.h> #include <sound/designware_i2s.h> @@ -648,6 +649,14 @@ static int dw_i2s_probe(struct platform_device *pdev) if (IS_ERR(dev->i2s_base)) return PTR_ERR(dev->i2s_base); + dev->reset = devm_reset_control_array_get_optional_shared(&pdev->dev); + if (IS_ERR(dev->reset)) + return PTR_ERR(dev->reset); + + ret = reset_control_deassert(dev->reset); + if (ret) + return ret; + dev->dev = &pdev->dev; irq = platform_get_irq_optional(pdev, 0); @@ -656,7 +665,7 @@ static int dw_i2s_probe(struct platform_device *pdev) pdev->name, dev); if (ret < 0) { dev_err(&pdev->dev, "failed to request irq\n"); - return ret; + goto err_assert_reset; } } @@ -676,24 +685,27 @@ static int dw_i2s_probe(struct platform_device *pdev) ret = dw_configure_dai_by_dt(dev, dw_i2s_dai, res); } if (ret < 0) - return ret; + goto err_assert_reset; if (dev->capability & DW_I2S_MASTER) { if (pdata) { dev->i2s_clk_cfg = pdata->i2s_clk_cfg; if (!dev->i2s_clk_cfg) { dev_err(&pdev->dev, "no clock configure method\n"); - return -ENODEV; + ret = -ENODEV; + goto err_assert_reset; } } dev->clk = devm_clk_get(&pdev->dev, clk_id); - if (IS_ERR(dev->clk)) - return PTR_ERR(dev->clk); + if (IS_ERR(dev->clk)) { + ret = PTR_ERR(dev->clk); + goto err_assert_reset; + } ret = clk_prepare_enable(dev->clk); if (ret < 0) - return ret; + goto err_assert_reset; } dev_set_drvdata(&pdev->dev, dev); @@ -727,6 +739,8 @@ static int dw_i2s_probe(struct platform_device *pdev) err_clk_disable: if (dev->capability & DW_I2S_MASTER) clk_disable_unprepare(dev->clk); +err_assert_reset: + reset_control_assert(dev->reset); return ret; } @@ -737,6 +751,7 @@ static void dw_i2s_remove(struct platform_device *pdev) if (dev->capability & DW_I2S_MASTER) clk_disable_unprepare(dev->clk); + reset_control_assert(dev->reset); pm_runtime_disable(&pdev->dev); } diff --git a/sound/soc/dwc/local.h b/sound/soc/dwc/local.h index 1c361eb6127e..d64bd4f8fd34 100644 --- a/sound/soc/dwc/local.h +++ b/sound/soc/dwc/local.h @@ -89,6 +89,7 @@ union dw_i2s_snd_dma_data { struct dw_i2s_dev { void __iomem *i2s_base; struct clk *clk; + struct reset_control *reset; int active; unsigned int capability; unsigned int quirks; -- 2.39.2

3 3

[PATCH 0/5] ASoC: MediaTek MT8195/86 Cleanups
by AngeloGioacchino Del Regno 09 May '23

09 May '23

This series performs some cleanups for mainly MT8195 and switches both MT8195 and MT8186's SOF driver to the snd_sof_ipc_process_reply() helper. AngeloGioacchino Del Regno (5): ASoC: SOF: mediatek: mt8195: Use snd_sof_ipc_process_reply() helper ASoC: SOF: mediatek: mt8186: Use snd_sof_ipc_process_reply() helper ASoC: mediatek: mt8195-afe-pcm: Simplify runtime PM during probe ASoC: mediatek: mt8195-afe-pcm: Simplify with dev_err_probe() ASoC: mediatek: mt8195-afe-pcm: Clean up unnecessary functions sound/soc/mediatek/mt8195/mt8195-afe-pcm.c | 99 ++++++++-------------- sound/soc/sof/mediatek/mt8186/mt8186.c | 36 +------- sound/soc/sof/mediatek/mt8195/mt8195.c | 36 +------- 3 files changed, 36 insertions(+), 135 deletions(-) -- 2.40.1

3 9

[PATCH] ASoC: dt-bindings: nau8540: Convert to dtschema
by Anup Sharma 09 May '23

09 May '23

Convert the NAU8540 audio CODEC bindings to DT schema Signed-off-by: Anup Sharma <anupnewsmail(a)gmail.com> --- .../devicetree/bindings/sound/nau8540.txt | 16 -------- .../bindings/sound/nuvoton,nau8540.yaml | 40 +++++++++++++++++++ 2 files changed, 40 insertions(+), 16 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sound/nau8540.txt create mode 100644 Documentation/devicetree/bindings/sound/nuvoton,nau8540.yaml diff --git a/Documentation/devicetree/bindings/sound/nau8540.txt b/Documentation/devicetree/bindings/sound/nau8540.txt deleted file mode 100644 index 307a76528320..000000000000 --- a/Documentation/devicetree/bindings/sound/nau8540.txt +++ /dev/null @@ -1,16 +0,0 @@ -NAU85L40 audio CODEC - -This device supports I2C only. - -Required properties: - - - compatible : "nuvoton,nau8540" - - - reg : the I2C address of the device. - -Example: - -codec: nau8540@1c { - compatible = "nuvoton,nau8540"; - reg = <0x1c>; -}; diff --git a/Documentation/devicetree/bindings/sound/nuvoton,nau8540.yaml b/Documentation/devicetree/bindings/sound/nuvoton,nau8540.yaml new file mode 100644 index 000000000000..ac344e435a5c --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nuvoton,nau8540.yaml @@ -0,0 +1,40 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/nuvoton,nau8540.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Nuvoton Technology Corporation NAU85L40 Audio CODEC + +maintainers: + - KCHSU0(a)nuvoton.com, broonie(a)kernel.org + +allOf: + - $ref: dai-common.yaml# + +properties: + compatible: + const: nuvoton,nau8540 + + reg: + maxItems: 1 + + "#sound-dai-cells": + const: 0 + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + codec@1c { + compatible = "nuvoton,nau8540"; + reg = <0x1c>; + }; + }; -- 2.34.1

3 2

[PATCH] ASoC: fsl_micfil: Fix error handler with pm_runtime_enable
by Shengjiu Wang 09 May '23

09 May '23

There is error message when defer probe happens: fsl-micfil-dai 30ca0000.micfil: Unbalanced pm_runtime_enable! Fix the error handler with pm_runtime_enable and add fsl_micfil_remove() for pm_runtime_disable. Fixes: 47a70e6fc9a8 ("ASoC: Add MICFIL SoC Digital Audio Interface driver.") Signed-off-by: Shengjiu Wang <shengjiu.wang(a)nxp.com> --- sound/soc/fsl/fsl_micfil.c | 14 +++++++++++++- 1 file changed, 13 insertions(+), 1 deletion(-) diff --git a/sound/soc/fsl/fsl_micfil.c b/sound/soc/fsl/fsl_micfil.c index 94341e4352b3..3f08082a55be 100644 --- a/sound/soc/fsl/fsl_micfil.c +++ b/sound/soc/fsl/fsl_micfil.c @@ -1159,7 +1159,7 @@ static int fsl_micfil_probe(struct platform_device *pdev) ret = devm_snd_dmaengine_pcm_register(&pdev->dev, NULL, 0); if (ret) { dev_err(&pdev->dev, "failed to pcm register\n"); - return ret; + goto err_pm_disable; } fsl_micfil_dai.capture.formats = micfil->soc->formats; @@ -1169,9 +1169,20 @@ static int fsl_micfil_probe(struct platform_device *pdev) if (ret) { dev_err(&pdev->dev, "failed to register component %s\n", fsl_micfil_component.name); + goto err_pm_disable; } return ret; + +err_pm_disable: + pm_runtime_disable(&pdev->dev); + + return ret; +} + +static void fsl_micfil_remove(struct platform_device *pdev) +{ + pm_runtime_disable(&pdev->dev); } static int __maybe_unused fsl_micfil_runtime_suspend(struct device *dev) @@ -1232,6 +1243,7 @@ static const struct dev_pm_ops fsl_micfil_pm_ops = { static struct platform_driver fsl_micfil_driver = { .probe = fsl_micfil_probe, + .remove_new = fsl_micfil_remove, .driver = { .name = "fsl-micfil-dai", .pm = &fsl_micfil_pm_ops, -- 2.34.1

2 1

[RESEND][PATCH v2 00/13] ASoC: add and use asoc_dummy_dlc
by Kuninori Morimoto 09 May '23

09 May '23

Hi Mark These are v2 patch-set of asoc_dummy_dlc. Many ASoC drivers are using dummy DAI. I have 2 concern about it. 1st one is there is no guarantee that local strings ("snd-soc-dummy-dai", "snd-soc-dummy") are kept until the card was binded if it was added at subfunction. 2nd one is we can use common snd_soc_dai_link_component for it. This patch-set adds common asoc_dummy_dlc, and use it. resend - rebased on latest asoc/for-6.4 branch v1 -> v2 - Separate intel patch into 3 - Topology codec doesn't use asoc_dummy_dlc Link: https://lore.kernel.org/r/874jpe3uqh.wl-kuninori.morimoto.gx@renesas.com Link: https://lore.kernel.org/r/87bkje0zzf.wl-kuninori.morimoto.gx@renesas.com Kuninori Morimoto (13): ASoC: soc-utils.c: add asoc_dummy_dlc ASoC: ti: use asoc_dummy_dlc ASoC: sof: use asoc_dummy_dlc ASoC: amd: use asoc_dummy_dlc ASoC: fsl: use asoc_dummy_dlc ASoC: qcom: use asoc_dummy_dlc ASoC: atmel: use asoc_dummy_dlc ASoC: meson: use asoc_dummy_dlc ASoC: intel: avs: use asoc_dummy_dlc ASoC: intel: sof: use asoc_dummy_dlc ASoC: intel: skylake: use asoc_dummy_dlc ASoC: simple_card_utils.c: use asoc_dummy_dlc ASoC: soc-topology.c: add comment for Platform/Codec include/sound/simple_card_utils.h | 1 - include/sound/soc.h | 1 + sound/soc/amd/acp/acp-mach-common.c | 43 ++++++++------------ sound/soc/atmel/atmel-classd.c | 8 ++-- sound/soc/atmel/atmel-pdmic.c | 8 ++-- sound/soc/fsl/imx-audmix.c | 14 +++---- sound/soc/fsl/imx-card.c | 11 +---- sound/soc/fsl/imx-rpmsg.c | 3 +- sound/soc/fsl/imx-spdif.c | 8 ++-- sound/soc/generic/simple-card-utils.c | 9 +--- sound/soc/intel/avs/boards/i2s_test.c | 6 +-- sound/soc/intel/boards/ehl_rt5660.c | 8 +--- sound/soc/intel/boards/skl_hda_dsp_generic.c | 8 +--- sound/soc/intel/boards/sof_cs42l42.c | 11 +---- sound/soc/intel/boards/sof_es8336.c | 11 +---- sound/soc/intel/boards/sof_nau8825.c | 11 +---- sound/soc/intel/boards/sof_pcm512x.c | 3 +- sound/soc/intel/boards/sof_rt5682.c | 14 ++----- sound/soc/intel/boards/sof_sdw.c | 13 +----- sound/soc/intel/boards/sof_ssp_amp.c | 18 +++----- sound/soc/meson/axg-card.c | 8 ++-- sound/soc/meson/meson-card-utils.c | 10 +---- sound/soc/qcom/common.c | 11 +---- sound/soc/soc-topology.c | 22 +++++----- sound/soc/soc-utils.c | 7 ++++ sound/soc/sof/nocodec.c | 8 ++-- sound/soc/ti/omap-hdmi.c | 8 ++-- 27 files changed, 89 insertions(+), 194 deletions(-) -- 2.25.1

1 13

[PATCH v3 30/38] sound: add HAS_IOPORT dependencies
by Niklas Schnelle 08 May '23

08 May '23

In a future patch HAS_IOPORT=n will result in inb()/outb() and friends not being declared. We thus need to add HAS_IOPORT as dependency for those drivers using them. Co-developed-by: Arnd Bergmann <arnd(a)kernel.org> Signed-off-by: Niklas Schnelle <schnelle(a)linux.ibm.com> --- sound/drivers/Kconfig | 3 +++ sound/isa/Kconfig | 31 ++++++++++++++++++++++++++--- sound/pci/Kconfig | 45 ++++++++++++++++++++++++++++++++----------- sound/pcmcia/Kconfig | 2 ++ 4 files changed, 67 insertions(+), 14 deletions(-) diff --git a/sound/drivers/Kconfig b/sound/drivers/Kconfig index be3009746f3a..864991d8776d 100644 --- a/sound/drivers/Kconfig +++ b/sound/drivers/Kconfig @@ -128,6 +128,7 @@ config SND_VIRMIDI config SND_MTPAV tristate "MOTU MidiTimePiece AV multiport MIDI" + depends on HAS_IOPORT select SND_RAWMIDI help To use a MOTU MidiTimePiece AV multiport MIDI adapter @@ -152,6 +153,7 @@ config SND_MTS64 config SND_SERIAL_U16550 tristate "UART16550 serial MIDI driver" + depends on HAS_IOPORT select SND_RAWMIDI help To include support for MIDI serial port interfaces, say Y here @@ -185,6 +187,7 @@ config SND_SERIAL_GENERIC config SND_MPU401 tristate "Generic MPU-401 UART driver" + depends on HAS_IOPORT select SND_MPU401_UART help Say Y here to include support for MIDI ports compatible with diff --git a/sound/isa/Kconfig b/sound/isa/Kconfig index 6ffa48dd5983..c7cef1e656fa 100644 --- a/sound/isa/Kconfig +++ b/sound/isa/Kconfig @@ -23,6 +23,7 @@ menuconfig SND_ISA bool "ISA sound devices" depends on ISA || COMPILE_TEST depends on ISA_DMA_API + depends on HAS_IOPORT default y help Support for sound devices connected via the ISA bus. @@ -31,6 +32,7 @@ if SND_ISA config SND_ADLIB tristate "AdLib FM card" + depends on HAS_IOPORT select SND_OPL3_LIB help Say Y here to include support for AdLib FM cards. @@ -41,6 +43,7 @@ config SND_ADLIB config SND_AD1816A tristate "Analog Devices SoundPort AD1816A" depends on PNP + depends on HAS_IOPORT select ISAPNP select SND_OPL3_LIB select SND_MPU401_UART @@ -69,6 +72,7 @@ config SND_AD1848 config SND_ALS100 tristate "Diamond Tech. DT-019x and Avance Logic ALSxxx" depends on PNP + depends on HAS_IOPORT select ISAPNP select SND_OPL3_LIB select SND_MPU401_UART @@ -84,6 +88,7 @@ config SND_ALS100 config SND_AZT1605 tristate "Aztech AZT1605 Driver" depends on SND + depends on HAS_IOPORT select SND_WSS_LIB select SND_MPU401_UART select SND_OPL3_LIB @@ -97,6 +102,7 @@ config SND_AZT1605 config SND_AZT2316 tristate "Aztech AZT2316 Driver" depends on SND + depends on HAS_IOPORT select SND_WSS_LIB select SND_MPU401_UART select SND_OPL3_LIB @@ -110,6 +116,7 @@ config SND_AZT2316 config SND_AZT2320 tristate "Aztech Systems AZT2320" depends on PNP + depends on HAS_IOPORT select ISAPNP select SND_OPL3_LIB select SND_MPU401_UART @@ -123,6 +130,7 @@ config SND_AZT2320 config SND_CMI8328 tristate "C-Media CMI8328" + depends on HAS_IOPORT select SND_WSS_LIB select SND_OPL3_LIB select SND_MPU401_UART @@ -135,6 +143,7 @@ config SND_CMI8328 config SND_CMI8330 tristate "C-Media CMI8330" + depends on HAS_IOPORT select SND_WSS_LIB select SND_SB16_DSP select SND_OPL3_LIB @@ -148,6 +157,7 @@ config SND_CMI8330 config SND_CS4231 tristate "Generic Cirrus Logic CS4231 driver" + depends on HAS_IOPORT select SND_MPU401_UART select SND_WSS_LIB help @@ -159,6 +169,7 @@ config SND_CS4231 config SND_CS4236 tristate "Generic Cirrus Logic CS4232/CS4236+ driver" + depends on HAS_IOPORT select SND_OPL3_LIB select SND_MPU401_UART select SND_WSS_LIB @@ -172,6 +183,7 @@ config SND_CS4236 config SND_ES1688 tristate "Generic ESS ES688/ES1688 and ES968 PnP driver" + depends on HAS_IOPORT select SND_OPL3_LIB select SND_MPU401_UART select SND_PCM @@ -184,6 +196,7 @@ config SND_ES1688 config SND_ES18XX tristate "Generic ESS ES18xx driver" + depends on HAS_IOPORT select SND_OPL3_LIB select SND_MPU401_UART select SND_PCM @@ -195,7 +208,7 @@ config SND_ES18XX config SND_SC6000 tristate "Gallant SC-6000/6600/7000 and Audio Excel DSP 16" - depends on HAS_IOPORT_MAP + depends on HAS_IOPORT_MAP && HAS_IOPORT select SND_WSS_LIB select SND_OPL3_LIB select SND_MPU401_UART @@ -223,6 +236,7 @@ config SND_GUSCLASSIC config SND_GUSEXTREME tristate "Gravis UltraSound Extreme" + depends on HAS_IOPORT select SND_OPL3_LIB select SND_MPU401_UART select SND_PCM @@ -273,6 +287,7 @@ config SND_INTERWAVE_STB config SND_JAZZ16 tristate "Media Vision Jazz16 card and compatibles" + depends on HAS_IOPORT select SND_OPL3_LIB select SND_MPU401_UART select SND_SB8_DSP @@ -289,6 +304,7 @@ config SND_JAZZ16 config SND_OPL3SA2 tristate "Yamaha OPL3-SA2/SA3" + depends on HAS_IOPORT select SND_OPL3_LIB select SND_MPU401_UART select SND_WSS_LIB @@ -301,6 +317,7 @@ config SND_OPL3SA2 config SND_OPTI92X_AD1848 tristate "OPTi 82C92x - AD1848" + depends on HAS_IOPORT select SND_OPL3_LIB select SND_OPL4_LIB select SND_MPU401_UART @@ -314,6 +331,7 @@ config SND_OPTI92X_AD1848 config SND_OPTI92X_CS4231 tristate "OPTi 82C92x - CS4231" + depends on HAS_IOPORT select SND_OPL3_LIB select SND_OPL4_LIB select SND_MPU401_UART @@ -327,6 +345,7 @@ config SND_OPTI92X_CS4231 config SND_OPTI93X tristate "OPTi 82C93x" + depends on HAS_IOPORT select SND_OPL3_LIB select SND_MPU401_UART select SND_WSS_LIB @@ -339,6 +358,7 @@ config SND_OPTI93X config SND_MIRO tristate "Miro miroSOUND PCM1pro/PCM12/PCM20radio driver" + depends on HAS_IOPORT select SND_OPL4_LIB select SND_WSS_LIB select SND_MPU401_UART @@ -352,6 +372,7 @@ config SND_MIRO config SND_SB8 tristate "Sound Blaster 1.0/2.0/Pro (8-bit)" + depends on HAS_IOPORT select SND_OPL3_LIB select SND_RAWMIDI select SND_SB8_DSP @@ -364,6 +385,7 @@ config SND_SB8 config SND_SB16 tristate "Sound Blaster 16 (PnP)" + depends on HAS_IOPORT select SND_OPL3_LIB select SND_MPU401_UART select SND_SB16_DSP @@ -376,6 +398,7 @@ config SND_SB16 config SND_SBAWE tristate "Sound Blaster AWE (32,64) (PnP)" + depends on HAS_IOPORT select SND_OPL3_LIB select SND_MPU401_UART select SND_SB16_DSP @@ -405,6 +428,7 @@ config SND_SB16_CSP config SND_SSCAPE tristate "Ensoniq SoundScape driver" + depends on HAS_IOPORT select SND_MPU401_UART select SND_WSS_LIB select FW_LOADER @@ -426,6 +450,7 @@ config SND_SSCAPE config SND_WAVEFRONT tristate "Turtle Beach Maui,Tropez,Tropez+ (Wavefront)" + depends on HAS_IOPORT select FW_LOADER select SND_OPL3_LIB select SND_MPU401_UART @@ -439,7 +464,7 @@ config SND_WAVEFRONT config SND_MSND_PINNACLE tristate "Turtle Beach MultiSound Pinnacle/Fiji driver" - depends on X86 + depends on X86 && HAS_IOPORT select FW_LOADER select SND_MPU401_UART select SND_PCM @@ -452,7 +477,7 @@ config SND_MSND_PINNACLE config SND_MSND_CLASSIC tristate "Support for Turtle Beach MultiSound Classic, Tahiti, Monterey" - depends on X86 + depends on X86 && HAS_IOPORT select FW_LOADER select SND_MPU401_UART select SND_PCM diff --git a/sound/pci/Kconfig b/sound/pci/Kconfig index a55836225401..e8780bade58f 100644 --- a/sound/pci/Kconfig +++ b/sound/pci/Kconfig @@ -26,7 +26,7 @@ config SND_ALS300 select SND_PCM select SND_AC97_CODEC select SND_OPL3_LIB - depends on ZONE_DMA + depends on ZONE_DMA && HAS_IOPORT help Say 'Y' or 'M' to include support for Avance Logic ALS300/ALS300+ @@ -36,6 +36,7 @@ config SND_ALS300 config SND_ALS4000 tristate "Avance Logic ALS4000" depends on ISA_DMA_API + depends on HAS_IOPORT select SND_OPL3_LIB select SND_MPU401_UART select SND_PCM @@ -51,7 +52,7 @@ config SND_ALI5451 tristate "ALi M5451 PCI Audio Controller" select SND_MPU401_UART select SND_AC97_CODEC - depends on ZONE_DMA + depends on ZONE_DMA && HAS_IOPORT help Say Y here to include support for the integrated AC97 sound device on motherboards using the ALi M5451 Audio Controller @@ -96,6 +97,7 @@ config SND_ATIIXP_MODEM config SND_AU8810 tristate "Aureal Advantage" + depends on HAS_IOPORT select SND_MPU401_UART select SND_AC97_CODEC help @@ -110,6 +112,7 @@ config SND_AU8810 config SND_AU8820 tristate "Aureal Vortex" + depends on HAS_IOPORT select SND_MPU401_UART select SND_AC97_CODEC help @@ -123,6 +126,7 @@ config SND_AU8820 config SND_AU8830 tristate "Aureal Vortex 2" + depends on HAS_IOPORT select SND_MPU401_UART select SND_AC97_CODEC help @@ -157,7 +161,7 @@ config SND_AZT3328 select SND_RAWMIDI select SND_AC97_CODEC select SND_TIMER - depends on ZONE_DMA + depends on ZONE_DMA && HAS_IOPORT help Say Y here to include support for Aztech AZF3328 (PCI168) soundcards. @@ -193,6 +197,7 @@ config SND_BT87X_OVERCLOCK config SND_CA0106 tristate "SB Audigy LS / Live 24bit" + depends on HAS_IOPORT select SND_AC97_CODEC select SND_RAWMIDI select SND_VMASTER @@ -205,6 +210,7 @@ config SND_CA0106 config SND_CMIPCI tristate "C-Media 8338, 8738, 8768, 8770" + depends on HAS_IOPORT select SND_OPL3_LIB select SND_MPU401_UART select SND_PCM @@ -221,6 +227,7 @@ config SND_OXYGEN_LIB config SND_OXYGEN tristate "C-Media 8786, 8787, 8788 (Oxygen)" + depends on HAS_IOPORT select SND_OXYGEN_LIB select SND_PCM select SND_MPU401_UART @@ -246,6 +253,7 @@ config SND_OXYGEN config SND_CS4281 tristate "Cirrus Logic (Sound Fusion) CS4281" + depends on HAS_IOPORT select SND_OPL3_LIB select SND_RAWMIDI select SND_AC97_CODEC @@ -257,6 +265,7 @@ config SND_CS4281 config SND_CS46XX tristate "Cirrus Logic (Sound Fusion) CS4280/CS461x/CS462x/CS463x" + depends on HAS_IOPORT select SND_RAWMIDI select SND_AC97_CODEC select FW_LOADER @@ -290,6 +299,7 @@ config SND_CS5530 config SND_CS5535AUDIO tristate "CS5535/CS5536 Audio" depends on X86_32 || MIPS || COMPILE_TEST + depends on HAS_IOPORT select SND_PCM select SND_AC97_CODEC help @@ -307,6 +317,7 @@ config SND_CS5535AUDIO config SND_CTXFI tristate "Creative Sound Blaster X-Fi" + depends on HAS_IOPORT select SND_PCM help If you want to use soundcards based on Creative Sound Blastr X-Fi @@ -468,7 +479,7 @@ config SND_EMU10K1 select SND_AC97_CODEC select SND_TIMER select SND_SEQ_DEVICE if SND_SEQUENCER != n - depends on ZONE_DMA + depends on ZONE_DMA && HAS_IOPORT help Say Y to include support for Sound Blaster PCI 512, Live!, Audigy and E-mu APS (partially supported) soundcards. @@ -491,7 +502,7 @@ config SND_EMU10K1X tristate "Emu10k1X (Dell OEM Version)" select SND_AC97_CODEC select SND_RAWMIDI - depends on ZONE_DMA + depends on ZONE_DMA && HAS_IOPORT help Say Y here to include support for the Dell OEM version of the Sound Blaster Live!. @@ -501,6 +512,7 @@ config SND_EMU10K1X config SND_ENS1370 tristate "(Creative) Ensoniq AudioPCI 1370" + depends on HAS_IOPORT select SND_RAWMIDI select SND_PCM help @@ -511,6 +523,7 @@ config SND_ENS1370 config SND_ENS1371 tristate "(Creative) Ensoniq AudioPCI 1371/1373" + depends on HAS_IOPORT select SND_RAWMIDI select SND_AC97_CODEC help @@ -525,7 +538,7 @@ config SND_ES1938 select SND_OPL3_LIB select SND_MPU401_UART select SND_AC97_CODEC - depends on ZONE_DMA + depends on ZONE_DMA && HAS_IOPORT help Say Y here to include support for soundcards based on ESS Solo-1 (ES1938, ES1946, ES1969) chips. @@ -537,7 +550,7 @@ config SND_ES1968 tristate "ESS ES1968/1978 (Maestro-1/2/2E)" select SND_MPU401_UART select SND_AC97_CODEC - depends on ZONE_DMA + depends on ZONE_DMA && HAS_IOPORT help Say Y here to include support for soundcards based on ESS Maestro 1/2/2E chips. @@ -569,6 +582,7 @@ config SND_ES1968_RADIO config SND_FM801 tristate "ForteMedia FM801" + depends on HAS_IOPORT select SND_OPL3_LIB select SND_MPU401_UART select SND_AC97_CODEC @@ -624,7 +638,7 @@ config SND_ICE1712 select SND_MPU401_UART select SND_AC97_CODEC select BITREVERSE - depends on ZONE_DMA + depends on ZONE_DMA && HAS_IOPORT help Say Y here to include support for soundcards based on the ICE1712 (Envy24) chip. @@ -640,6 +654,7 @@ config SND_ICE1712 config SND_ICE1724 tristate "ICE/VT1724/1720 (Envy24HT/PT)" + depends on HAS_IOPORT select SND_RAWMIDI select SND_AC97_CODEC select SND_VMASTER @@ -712,7 +727,7 @@ config SND_LX6464ES config SND_MAESTRO3 tristate "ESS Allegro/Maestro3" select SND_AC97_CODEC - depends on ZONE_DMA + depends on ZONE_DMA && HAS_IOPORT help Say Y here to include support for soundcards based on ESS Maestro 3 (Allegro) chips. @@ -753,6 +768,7 @@ config SND_NM256 config SND_PCXHR tristate "Digigram PCXHR" + depends on HAS_IOPORT select FW_LOADER select SND_PCM select SND_HWDEP @@ -764,6 +780,7 @@ config SND_PCXHR config SND_RIPTIDE tristate "Conexant Riptide" + depends on HAS_IOPORT select FW_LOADER select SND_OPL3_LIB select SND_MPU401_UART @@ -808,6 +825,7 @@ config SND_RME9652 config SND_SE6X tristate "Studio Evolution SE6X" depends on SND_OXYGEN=n && SND_VIRTUOSO=n # PCI ID conflict + depends on HAS_IOPORT select SND_OXYGEN_LIB select SND_PCM select SND_MPU401_UART @@ -830,7 +848,7 @@ config SND_SONICVIBES select SND_OPL3_LIB select SND_MPU401_UART select SND_AC97_CODEC - depends on ZONE_DMA + depends on ZONE_DMA && HAS_IOPORT help Say Y here to include support for soundcards based on the S3 SonicVibes chip. @@ -842,7 +860,7 @@ config SND_TRIDENT tristate "Trident 4D-Wave DX/NX; SiS 7018" select SND_MPU401_UART select SND_AC97_CODEC - depends on ZONE_DMA + depends on ZONE_DMA && HAS_IOPORT help Say Y here to include support for soundcards based on Trident 4D-Wave DX/NX or SiS 7018 chips. @@ -852,6 +870,7 @@ config SND_TRIDENT config SND_VIA82XX tristate "VIA 82C686A/B, 8233/8235 AC97 Controller" + depends on HAS_IOPORT select SND_MPU401_UART select SND_AC97_CODEC help @@ -863,6 +882,7 @@ config SND_VIA82XX config SND_VIA82XX_MODEM tristate "VIA 82C686A/B, 8233 based Modems" + depends on HAS_IOPORT select SND_AC97_CODEC help Say Y here to include support for the integrated MC97 modem on @@ -873,6 +893,7 @@ config SND_VIA82XX_MODEM config SND_VIRTUOSO tristate "Asus Virtuoso 66/100/200 (Xonar)" + depends on HAS_IOPORT select SND_OXYGEN_LIB select SND_PCM select SND_MPU401_UART @@ -889,6 +910,7 @@ config SND_VIRTUOSO config SND_VX222 tristate "Digigram VX222" + depends on HAS_IOPORT select SND_VX_LIB help Say Y here to include support for Digigram VX222 soundcards. @@ -898,6 +920,7 @@ config SND_VX222 config SND_YMFPCI tristate "Yamaha YMF724/740/744/754" + depends on HAS_IOPORT select SND_OPL3_LIB select SND_MPU401_UART select SND_AC97_CODEC diff --git a/sound/pcmcia/Kconfig b/sound/pcmcia/Kconfig index 10291c43cb18..b133ad423f84 100644 --- a/sound/pcmcia/Kconfig +++ b/sound/pcmcia/Kconfig @@ -13,6 +13,7 @@ if SND_PCMCIA && PCMCIA config SND_VXPOCKET tristate "Digigram VXpocket" select SND_VX_LIB + depends on HAS_IOPORT help Say Y here to include support for Digigram VXpocket and VXpocket 440 soundcards. @@ -22,6 +23,7 @@ config SND_VXPOCKET config SND_PDAUDIOCF tristate "Sound Core PDAudioCF" + depends on HAS_IOPORT select SND_PCM help Say Y here to include support for Sound Core PDAudioCF -- 2.37.2

2 2

[PATCH] soundwire: intel: Make DEV_NUM_IDA_MIN a module param
by Richard Fitzgerald 08 May '23

08 May '23

Add a module param so that globally-unique peripheral ID allocation is only enabled if wanted. The globally-unique IDs were introduced by commit c60561014257 ("soundwire: bus: allow device number to be unique at system level") and commit 1f2dcf3a154a ("soundwire: intel: set dev_num_ida_min") Assigning globally-unique IDs limits the total number of peripherals in a system, and the above two commits limit to a maximum of 8 peripherals. We now have hardware with more than 8 peripherals in total, so this limit is a problem. As the original commit says that it is only for debug it can be made optional. Signed-off-by: Richard Fitzgerald <rf(a)opensource.cirrus.com> --- drivers/soundwire/intel_auxdevice.c | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-) diff --git a/drivers/soundwire/intel_auxdevice.c b/drivers/soundwire/intel_auxdevice.c index b21e86084f7b..9ebbf652e47a 100644 --- a/drivers/soundwire/intel_auxdevice.c +++ b/drivers/soundwire/intel_auxdevice.c @@ -23,8 +23,13 @@ #include "intel.h" #include "intel_auxdevice.h" -/* IDA min selected to avoid conflicts with HDaudio/iDISP SDI values */ -#define INTEL_DEV_NUM_IDA_MIN 4 +/* + * sdw_dev_num_min: Set to non-zero to enable globally-unique peripheral IDs. + * The value is the minimum ID that will be allocated. + */ +static int intel_dev_num_ida_min; +module_param_named(sdw_dev_num_min, intel_dev_num_ida_min, int, 0444); +MODULE_PARM_DESC(sdw_dev_num_min, "SoundWire Intel Master min globally-unique ID (0 to disable)"); #define INTEL_MASTER_SUSPEND_DELAY_MS 3000 @@ -148,7 +153,7 @@ static int intel_link_probe(struct auxiliary_device *auxdev, cdns->msg_count = 0; bus->link_id = auxdev->id; - bus->dev_num_ida_min = INTEL_DEV_NUM_IDA_MIN; + bus->dev_num_ida_min = intel_dev_num_ida_min; bus->clk_stop_timeout = 1; sdw_cdns_probe(cdns); -- 2.30.2

2 1

[PATCH] ASoC: amd: yc: Add DMI entry to support System76 Pangolin 12
by Tim Crawford 08 May '23

08 May '23

From: Jeremy Soller <jeremy(a)system76.com> Add pang12 quirk to enable the internal microphone. Signed-off-by: Jeremy Soller <jeremy(a)system76.com> Signed-off-by: Tim Crawford <tcrawford(a)system76.com> --- sound/soc/amd/yc/acp6x-mach.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/sound/soc/amd/yc/acp6x-mach.c b/sound/soc/amd/yc/acp6x-mach.c index b9958e555367..84b401b685f7 100644 --- a/sound/soc/amd/yc/acp6x-mach.c +++ b/sound/soc/amd/yc/acp6x-mach.c @@ -297,6 +297,13 @@ static const struct dmi_system_id yc_acp_quirk_table[] = { DMI_MATCH(DMI_BOARD_NAME, "8A22"), } }, + { + .driver_data = &acp6x_card, + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, "System76"), + DMI_MATCH(DMI_PRODUCT_VERSION, "pang12"), + } + }, {} }; -- 2.40.1

2 1

[PATCH 1/1] ASoC: dwc: limit the number of overrun messages
by Maxim Kochetkov 08 May '23

08 May '23

On slow CPU (FPGA/QEMU emulated) printing overrun messages from interrupt handler to uart console may leads to more overrun errors. So use dev_err_ratelimited to limit the number of error messages. Signed-off-by: Maxim Kochetkov <fido_max(a)inbox.ru> --- sound/soc/dwc/dwc-i2s.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/sound/soc/dwc/dwc-i2s.c b/sound/soc/dwc/dwc-i2s.c index acdf98b2ee9c..ca20cade6840 100644 --- a/sound/soc/dwc/dwc-i2s.c +++ b/sound/soc/dwc/dwc-i2s.c @@ -132,13 +132,13 @@ static irqreturn_t i2s_irq_handler(int irq, void *dev_id) /* Error Handling: TX */ if (isr[i] & ISR_TXFO) { - dev_err(dev->dev, "TX overrun (ch_id=%d)\n", i); + dev_err_ratelimited(dev->dev, "TX overrun (ch_id=%d)\n", i); irq_valid = true; } /* Error Handling: TX */ if (isr[i] & ISR_RXFO) { - dev_err(dev->dev, "RX overrun (ch_id=%d)\n", i); + dev_err_ratelimited(dev->dev, "RX overrun (ch_id=%d)\n", i); irq_valid = true; } } -- 2.39.2

2 1

[PATCH] ALSA: uapi: pcm: control the filling of the silence samples for drain
by Jaroslav Kysela 08 May '23

08 May '23

Introduce SNDRV_PCM_INFO_PERFECT_DRAIN and SNDRV_PCM_HW_PARAMS_NO_DRAIN_SILENCE flags to fully control the filling of the silence samples in the drain ioctl. Actually, the configurable silencing is going to be implemented in the user space [1], but drivers (hardware) may not require this operation. Those flags do the bidirectional setup for this operation: 1) driver may notify the presence of the perfect drain 2) user space may not require the filling of the silence samples to inhibit clicks If we decide to move this operation to the kernel space in future, the SNDRV_PCM_INFO_PERFECT_DRAIN flag may handle this situation without double "silence" processing (user + kernel space). The ALSA API should be universal, so forcing the behaviour (modifying of the ring buffer with any samples) for the drain operation is not ideal. [1] https://lore.kernel.org/alsa-devel/20230502115010.986325-1-perex@perex.cz/ Signed-off-by: Jaroslav Kysela <perex(a)perex.cz> --- include/uapi/sound/asound.h | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/include/uapi/sound/asound.h b/include/uapi/sound/asound.h index 0aa955aa8246..e4b0f95694c5 100644 --- a/include/uapi/sound/asound.h +++ b/include/uapi/sound/asound.h @@ -274,6 +274,7 @@ typedef int __bitwise snd_pcm_subformat_t; #define SNDRV_PCM_INFO_DOUBLE 0x00000004 /* Double buffering needed for PCM start/stop */ #define SNDRV_PCM_INFO_BATCH 0x00000010 /* double buffering */ #define SNDRV_PCM_INFO_SYNC_APPLPTR 0x00000020 /* need the explicit sync of appl_ptr update */ +#define SNDRV_PCM_INFO_PERFECT_DRAIN 0x00000040 /* silencing at the end of stream is not required */ #define SNDRV_PCM_INFO_INTERLEAVED 0x00000100 /* channels are interleaved */ #define SNDRV_PCM_INFO_NONINTERLEAVED 0x00000200 /* channels are not interleaved */ #define SNDRV_PCM_INFO_COMPLEX 0x00000400 /* complex frame organization (mmap only) */ @@ -383,6 +384,9 @@ typedef int snd_pcm_hw_param_t; #define SNDRV_PCM_HW_PARAMS_NORESAMPLE (1<<0) /* avoid rate resampling */ #define SNDRV_PCM_HW_PARAMS_EXPORT_BUFFER (1<<1) /* export buffer */ #define SNDRV_PCM_HW_PARAMS_NO_PERIOD_WAKEUP (1<<2) /* disable period wakeups */ +#define SNDRV_PCM_HW_PARAMS_NO_DRAIN_SILENCE (1<<3) /* supress drain with the filling + * of the silence samples + */ struct snd_interval { unsigned int min, max; -- 2.39.2

2 2

[PATCH v2] ALSA: emu10k1: macro-ize snd_emu10k1_ptr_{read,write}()
by Oswald Buddenhagen 08 May '23

08 May '23

The idea to encode the bitfield manipulation in the register address is quite clever, but it's somewhat wasteful to do these calculations at runtime, given that they are all constants. So change that. This yields a marginal saving in runtime cost at a marginal cost in code side (less than 400 bytes). The call sites where the read/write is done with a non-constant register needed adjustment, so there is a bit of churn involved. On the upside, this makes the various use cases more obvious, and makes it easier to grep for them. snd_emu10k1_ptr_{read,write}() must be macros, as they check the constness of the passed register argument, and the C language has no provisions for doing this differently. The added bitfield manipulation macros will be used separately as well. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- v2: - the snd_emu10k1_ptr_{read,write} macros now check that the register is actually a constant - introduced inline snd_emu10k1_ptr_{read,write}_idx functions - replaced the incorrect usages of the macros, which saves > 2kb dead code - re-arranged the declarations for a more logical order - elaborate a bit more in the commit message --- include/sound/emu10k1.h | 44 +++++++++++- sound/pci/emu10k1/emu10k1_main.c | 8 +-- sound/pci/emu10k1/emufx.c | 66 +++++++++--------- sound/pci/emu10k1/emumixer.c | 2 +- sound/pci/emu10k1/emumpu401.c | 4 +- sound/pci/emu10k1/emupcm.c | 63 +++++++++-------- sound/pci/emu10k1/emuproc.c | 12 ++-- sound/pci/emu10k1/io.c | 114 ++++++++++++++----------------- 8 files changed, 174 insertions(+), 139 deletions(-) diff --git a/include/sound/emu10k1.h b/include/sound/emu10k1.h index 8fe80dcee71b..ca7be531969c 100644 --- a/include/sound/emu10k1.h +++ b/include/sound/emu10k1.h @@ -1773,8 +1773,48 @@ int snd_emu10k1_fx8010_tram_setup(struct snd_emu10k1 *emu, u32 size); int snd_emu10k1_done(struct snd_emu10k1 * emu); /* I/O functions */ -unsigned int snd_emu10k1_ptr_read(struct snd_emu10k1 * emu, unsigned int reg, unsigned int chn); -void snd_emu10k1_ptr_write(struct snd_emu10k1 *emu, unsigned int reg, unsigned int chn, unsigned int data); + +u32 snd_emu10k1_ptr_read_raw(struct snd_emu10k1 *emu, u32 reg); +void snd_emu10k1_ptr_write_raw(struct snd_emu10k1 *emu, u32 reg, u32 data); +void snd_emu10k1_ptr_modify(struct snd_emu10k1 *emu, u32 reg, u32 and_mask, u32 or_mask); + +static inline u32 snd_emu10k1_ptr_read_idx(struct snd_emu10k1 *emu, u16 reg, u8 voice) +{ + return snd_emu10k1_ptr_read_raw(emu, ((u32)reg << 16) | voice); +} + +static inline void snd_emu10k1_ptr_write_idx(struct snd_emu10k1 *emu, u16 reg, u8 voice, u32 data) +{ + snd_emu10k1_ptr_write_raw(emu, ((u32)reg << 16) | voice, data); +} + +#define REG_SHIFT(r) (((r) >> 16) & 0x1f) +#define REG_SIZE(r) (((r) >> 24) & 0x1f) +#define REG_MASK0(r) ((1U << REG_SIZE(r)) - 1U) +#define REG_MASK(r) (REG_MASK0(r) << REG_SHIFT(r)) +#define REG_ADDR(r, v) ((((r) & 0xffff) << 16) | (v)) +#define REG_VAL_GET(r, v) ((v & REG_MASK(r)) >> REG_SHIFT(r)) +#define REG_VAL_PUT(r, v) ((v) << REG_SHIFT(r)) + +#define snd_emu10k1_ptr_read(emu, reg, voice) \ + ({ \ + enum { reg_must_be_constant = reg }; \ + u32 data = snd_emu10k1_ptr_read_raw(emu, REG_ADDR(reg, voice)); \ + if (REG_SIZE(reg)) \ + data = REG_VAL_GET(reg, data); \ + data; \ + }) + +#define snd_emu10k1_ptr_write(emu, reg, voice, data) \ + do { \ + enum { reg_must_be_constant = reg }; \ + if (REG_SIZE(reg)) \ + snd_emu10k1_ptr_modify(emu, REG_ADDR(reg, voice), \ + ~REG_MASK(reg), REG_VAL_PUT(reg, data)); \ + else \ + snd_emu10k1_ptr_write_raw(emu, REG_ADDR(reg, voice), data); \ + } while (0) + unsigned int snd_emu10k1_ptr20_read(struct snd_emu10k1 * emu, unsigned int reg, unsigned int chn); void snd_emu10k1_ptr20_write(struct snd_emu10k1 *emu, unsigned int reg, unsigned int chn, unsigned int data); int snd_emu10k1_spi_write(struct snd_emu10k1 * emu, unsigned int data); diff --git a/sound/pci/emu10k1/emu10k1_main.c b/sound/pci/emu10k1/emu10k1_main.c index 3abdaf1b9624..576391a0d9c6 100644 --- a/sound/pci/emu10k1/emu10k1_main.c +++ b/sound/pci/emu10k1/emu10k1_main.c @@ -1985,11 +1985,11 @@ void snd_emu10k1_suspend_regs(struct snd_emu10k1 *emu) val = emu->saved_ptr; for (reg = saved_regs; *reg != 0xff; reg++) for (i = 0; i < NUM_G; i++, val++) - *val = snd_emu10k1_ptr_read(emu, *reg, i); + *val = snd_emu10k1_ptr_read_idx(emu, *reg, i); if (emu->audigy) { for (reg = saved_regs_audigy; *reg != 0xff; reg++) for (i = 0; i < NUM_G; i++, val++) - *val = snd_emu10k1_ptr_read(emu, *reg, i); + *val = snd_emu10k1_ptr_read_idx(emu, *reg, i); } if (emu->audigy) emu->saved_a_iocfg = inw(emu->port + A_IOCFG); @@ -2025,11 +2025,11 @@ void snd_emu10k1_resume_regs(struct snd_emu10k1 *emu) val = emu->saved_ptr; for (reg = saved_regs; *reg != 0xff; reg++) for (i = 0; i < NUM_G; i++, val++) - snd_emu10k1_ptr_write(emu, *reg, i, *val); + snd_emu10k1_ptr_write_idx(emu, *reg, i, *val); if (emu->audigy) { for (reg = saved_regs_audigy; *reg != 0xff; reg++) for (i = 0; i < NUM_G; i++, val++) - snd_emu10k1_ptr_write(emu, *reg, i, *val); + snd_emu10k1_ptr_write_idx(emu, *reg, i, *val); } } #endif diff --git a/sound/pci/emu10k1/emufx.c b/sound/pci/emu10k1/emufx.c index db211a6e8a47..757623687a5b 100644 --- a/sound/pci/emu10k1/emufx.c +++ b/sound/pci/emu10k1/emufx.c @@ -353,29 +353,31 @@ static int snd_emu10k1_gpr_ctl_put(struct snd_kcontrol *kcontrol, struct snd_ctl val = ctl->value[i] = nval; switch (ctl->translation) { case EMU10K1_GPR_TRANSLATION_NONE: - snd_emu10k1_ptr_write(emu, emu->gpr_base + ctl->gpr[i], 0, val); + snd_emu10k1_ptr_write_raw(emu, emu->gpr_base + ctl->gpr[i], val); break; case EMU10K1_GPR_TRANSLATION_TABLE100: - snd_emu10k1_ptr_write(emu, emu->gpr_base + ctl->gpr[i], 0, db_table[val]); + snd_emu10k1_ptr_write_raw(emu, emu->gpr_base + ctl->gpr[i], db_table[val]); break; case EMU10K1_GPR_TRANSLATION_BASS: if ((ctl->count % 5) != 0 || (ctl->count / 5) != ctl->vcount) { change = -EIO; goto __error; } for (j = 0; j < 5; j++) - snd_emu10k1_ptr_write(emu, emu->gpr_base + ctl->gpr[j * ctl->vcount + i], 0, bass_table[val][j]); + snd_emu10k1_ptr_write_raw(emu, emu->gpr_base + ctl->gpr[j * ctl->vcount + i], + bass_table[val][j]); break; case EMU10K1_GPR_TRANSLATION_TREBLE: if ((ctl->count % 5) != 0 || (ctl->count / 5) != ctl->vcount) { change = -EIO; goto __error; } for (j = 0; j < 5; j++) - snd_emu10k1_ptr_write(emu, emu->gpr_base + ctl->gpr[j * ctl->vcount + i], 0, treble_table[val][j]); + snd_emu10k1_ptr_write_raw(emu, emu->gpr_base + ctl->gpr[j * ctl->vcount + i], + treble_table[val][j]); break; case EMU10K1_GPR_TRANSLATION_ONOFF: - snd_emu10k1_ptr_write(emu, emu->gpr_base + ctl->gpr[i], 0, onoff_table[val]); + snd_emu10k1_ptr_write_raw(emu, emu->gpr_base + ctl->gpr[i], onoff_table[val]); break; } } @@ -395,10 +397,10 @@ static void snd_emu10k1_fx8010_interrupt(struct snd_emu10k1 *emu) irq = emu->fx8010.irq_handlers; while (irq) { nirq = irq->next; /* irq ptr can be removed from list */ - if (snd_emu10k1_ptr_read(emu, emu->gpr_base + irq->gpr_running, 0) & 0xffff0000) { + if (snd_emu10k1_ptr_read_raw(emu, emu->gpr_base + irq->gpr_running) & 0xffff0000) { if (irq->handler) irq->handler(emu, irq->private_data); - snd_emu10k1_ptr_write(emu, emu->gpr_base + irq->gpr_running, 0, 1); + snd_emu10k1_ptr_write_raw(emu, emu->gpr_base + irq->gpr_running, 1); } irq = nirq; } @@ -494,13 +496,13 @@ static void snd_emu10k1_audigy_write_op(struct snd_emu10k1_fx8010_code *icode, static void snd_emu10k1_efx_write(struct snd_emu10k1 *emu, unsigned int pc, unsigned int data) { pc += emu->audigy ? A_MICROCODEBASE : MICROCODEBASE; - snd_emu10k1_ptr_write(emu, pc, 0, data); + snd_emu10k1_ptr_write_raw(emu, pc, data); } unsigned int snd_emu10k1_efx_read(struct snd_emu10k1 *emu, unsigned int pc) { pc += emu->audigy ? A_MICROCODEBASE : MICROCODEBASE; - return snd_emu10k1_ptr_read(emu, pc, 0); + return snd_emu10k1_ptr_read_raw(emu, pc); } static int snd_emu10k1_gpr_poke(struct snd_emu10k1 *emu, @@ -517,7 +519,7 @@ static int snd_emu10k1_gpr_poke(struct snd_emu10k1 *emu, val = icode->gpr_map[gpr]; else if (get_user(val, (__user u32 *)&icode->gpr_map[gpr])) return -EFAULT; - snd_emu10k1_ptr_write(emu, emu->gpr_base + gpr, 0, val); + snd_emu10k1_ptr_write_raw(emu, emu->gpr_base + gpr, val); } return 0; } @@ -530,7 +532,7 @@ static int snd_emu10k1_gpr_peek(struct snd_emu10k1 *emu, for (gpr = 0; gpr < (emu->audigy ? 0x200 : 0x100); gpr++) { set_bit(gpr, icode->gpr_valid); - val = snd_emu10k1_ptr_read(emu, emu->gpr_base + gpr, 0); + val = snd_emu10k1_ptr_read_raw(emu, emu->gpr_base + gpr); if (put_user(val, (__user u32 *)&icode->gpr_map[gpr])) return -EFAULT; } @@ -555,12 +557,12 @@ static int snd_emu10k1_tram_poke(struct snd_emu10k1 *emu, get_user(addr, (__user __u32 *)&icode->tram_addr_map[tram])) return -EFAULT; } - snd_emu10k1_ptr_write(emu, TANKMEMDATAREGBASE + tram, 0, val); + snd_emu10k1_ptr_write_raw(emu, TANKMEMDATAREGBASE + tram, val); if (!emu->audigy) { - snd_emu10k1_ptr_write(emu, TANKMEMADDRREGBASE + tram, 0, addr); + snd_emu10k1_ptr_write_raw(emu, TANKMEMADDRREGBASE + tram, addr); } else { - snd_emu10k1_ptr_write(emu, TANKMEMADDRREGBASE + tram, 0, addr << 12); - snd_emu10k1_ptr_write(emu, A_TANKMEMCTLREGBASE + tram, 0, addr >> 20); + snd_emu10k1_ptr_write_raw(emu, TANKMEMADDRREGBASE + tram, addr << 12); + snd_emu10k1_ptr_write_raw(emu, A_TANKMEMCTLREGBASE + tram, addr >> 20); } } return 0; @@ -575,12 +577,12 @@ static int snd_emu10k1_tram_peek(struct snd_emu10k1 *emu, memset(icode->tram_valid, 0, sizeof(icode->tram_valid)); for (tram = 0; tram < (emu->audigy ? 0x100 : 0xa0); tram++) { set_bit(tram, icode->tram_valid); - val = snd_emu10k1_ptr_read(emu, TANKMEMDATAREGBASE + tram, 0); + val = snd_emu10k1_ptr_read_raw(emu, TANKMEMDATAREGBASE + tram); if (!emu->audigy) { - addr = snd_emu10k1_ptr_read(emu, TANKMEMADDRREGBASE + tram, 0); + addr = snd_emu10k1_ptr_read_raw(emu, TANKMEMADDRREGBASE + tram); } else { - addr = snd_emu10k1_ptr_read(emu, TANKMEMADDRREGBASE + tram, 0) >> 12; - addr |= snd_emu10k1_ptr_read(emu, A_TANKMEMCTLREGBASE + tram, 0) << 20; + addr = snd_emu10k1_ptr_read_raw(emu, TANKMEMADDRREGBASE + tram) >> 12; + addr |= snd_emu10k1_ptr_read_raw(emu, A_TANKMEMCTLREGBASE + tram) << 20; } if (put_user(val, (__user u32 *)&icode->tram_data_map[tram]) || put_user(addr, (__user u32 *)&icode->tram_addr_map[tram])) @@ -2730,16 +2732,16 @@ void snd_emu10k1_efx_suspend(struct snd_emu10k1 *emu) len = emu->audigy ? 0x200 : 0x100; for (i = 0; i < len; i++) - emu->saved_gpr[i] = snd_emu10k1_ptr_read(emu, emu->gpr_base + i, 0); + emu->saved_gpr[i] = snd_emu10k1_ptr_read_raw(emu, emu->gpr_base + i); len = emu->audigy ? 0x100 : 0xa0; for (i = 0; i < len; i++) { - emu->tram_val_saved[i] = snd_emu10k1_ptr_read(emu, TANKMEMDATAREGBASE + i, 0); - emu->tram_addr_saved[i] = snd_emu10k1_ptr_read(emu, TANKMEMADDRREGBASE + i, 0); + emu->tram_val_saved[i] = snd_emu10k1_ptr_read_raw(emu, TANKMEMDATAREGBASE + i); + emu->tram_addr_saved[i] = snd_emu10k1_ptr_read_raw(emu, TANKMEMADDRREGBASE + i); if (emu->audigy) { emu->tram_addr_saved[i] >>= 12; emu->tram_addr_saved[i] |= - snd_emu10k1_ptr_read(emu, A_TANKMEMCTLREGBASE + i, 0) << 20; + snd_emu10k1_ptr_read_raw(emu, A_TANKMEMCTLREGBASE + i) << 20; } } @@ -2774,20 +2776,20 @@ void snd_emu10k1_efx_resume(struct snd_emu10k1 *emu) len = emu->audigy ? 0x200 : 0x100; for (i = 0; i < len; i++) - snd_emu10k1_ptr_write(emu, emu->gpr_base + i, 0, emu->saved_gpr[i]); + snd_emu10k1_ptr_write_raw(emu, emu->gpr_base + i, emu->saved_gpr[i]); len = emu->audigy ? 0x100 : 0xa0; for (i = 0; i < len; i++) { - snd_emu10k1_ptr_write(emu, TANKMEMDATAREGBASE + i, 0, - emu->tram_val_saved[i]); + snd_emu10k1_ptr_write_raw(emu, TANKMEMDATAREGBASE + i, + emu->tram_val_saved[i]); if (! emu->audigy) - snd_emu10k1_ptr_write(emu, TANKMEMADDRREGBASE + i, 0, - emu->tram_addr_saved[i]); + snd_emu10k1_ptr_write_raw(emu, TANKMEMADDRREGBASE + i, + emu->tram_addr_saved[i]); else { - snd_emu10k1_ptr_write(emu, TANKMEMADDRREGBASE + i, 0, - emu->tram_addr_saved[i] << 12); - snd_emu10k1_ptr_write(emu, TANKMEMADDRREGBASE + i, 0, - emu->tram_addr_saved[i] >> 20); + snd_emu10k1_ptr_write_raw(emu, TANKMEMADDRREGBASE + i, + emu->tram_addr_saved[i] << 12); + snd_emu10k1_ptr_write_raw(emu, TANKMEMADDRREGBASE + i, + emu->tram_addr_saved[i] >> 20); } } diff --git a/sound/pci/emu10k1/emumixer.c b/sound/pci/emu10k1/emumixer.c index 8fce3413f4ae..342fcbb8b7b5 100644 --- a/sound/pci/emu10k1/emumixer.c +++ b/sound/pci/emu10k1/emumixer.c @@ -1158,7 +1158,7 @@ static int snd_emu10k1_spdif_put(struct snd_kcontrol *kcontrol, spin_lock_irqsave(&emu->reg_lock, flags); change = val != emu->spdif_bits[idx]; if (change) { - snd_emu10k1_ptr_write(emu, SPCS0 + idx, 0, val); + snd_emu10k1_ptr_write_raw(emu, SPCS0 + idx, val); emu->spdif_bits[idx] = val; } spin_unlock_irqrestore(&emu->reg_lock, flags); diff --git a/sound/pci/emu10k1/emumpu401.c b/sound/pci/emu10k1/emumpu401.c index 3ce9b2129ce6..0b42e42798b1 100644 --- a/sound/pci/emu10k1/emumpu401.c +++ b/sound/pci/emu10k1/emumpu401.c @@ -16,16 +16,16 @@ static inline unsigned char mpu401_read(struct snd_emu10k1 *emu, struct snd_emu10k1_midi *mpu, int idx) { if (emu->audigy) - return (unsigned char)snd_emu10k1_ptr_read(emu, mpu->port + idx, 0); + return (unsigned char)snd_emu10k1_ptr_read_raw(emu, mpu->port + idx); else return inb(emu->port + mpu->port + idx); } static inline void mpu401_write(struct snd_emu10k1 *emu, struct snd_emu10k1_midi *mpu, int data, int idx) { if (emu->audigy) - snd_emu10k1_ptr_write(emu, mpu->port + idx, 0, data); + snd_emu10k1_ptr_write_raw(emu, mpu->port + idx, data); else outb(data, emu->port + mpu->port + idx); } diff --git a/sound/pci/emu10k1/emupcm.c b/sound/pci/emu10k1/emupcm.c index b0c0ef342756..6ef4926da53c 100644 --- a/sound/pci/emu10k1/emupcm.c +++ b/sound/pci/emu10k1/emupcm.c @@ -528,7 +528,7 @@ static int snd_emu10k1_capture_prepare(struct snd_pcm_substream *substream) int idx; /* zeroing the buffer size will stop capture */ - snd_emu10k1_ptr_write(emu, epcm->capture_bs_reg, 0, 0); + snd_emu10k1_ptr_write_raw(emu, epcm->capture_bs_reg, 0); switch (epcm->type) { case CAPTURE_AC97ADC: snd_emu10k1_ptr_write(emu, ADCCR, 0, 0); @@ -543,7 +543,7 @@ static int snd_emu10k1_capture_prepare(struct snd_pcm_substream *substream) default: break; } - snd_emu10k1_ptr_write(emu, epcm->capture_ba_reg, 0, runtime->dma_addr); + snd_emu10k1_ptr_write_raw(emu, epcm->capture_ba_reg, runtime->dma_addr); epcm->capture_bufsize = snd_pcm_lib_buffer_bytes(substream); epcm->capture_bs_val = 0; for (idx = 0; idx < 31; idx++) { @@ -583,9 +583,9 @@ static void snd_emu10k1_playback_invalidate_cache(struct snd_emu10k1 *emu, int e cs = (sample == 0) ? (32-ccis) : (64-ccis+1) >> 1; if (cs > 16) cs = 16; for (i = 0; i < cs; i++) { - snd_emu10k1_ptr_write(emu, CD0 + i, voice, sample); + snd_emu10k1_ptr_write_idx(emu, CD0 + i, voice, sample); if (stereo) { - snd_emu10k1_ptr_write(emu, CD0 + i, voice + 1, sample); + snd_emu10k1_ptr_write_idx(emu, CD0 + i, voice + 1, sample); } } /* reset cache */ @@ -771,16 +771,16 @@ static int snd_emu10k1_capture_trigger(struct snd_pcm_substream *substream, default: break; } - snd_emu10k1_ptr_write(emu, epcm->capture_bs_reg, 0, epcm->capture_bs_val); + snd_emu10k1_ptr_write_raw(emu, epcm->capture_bs_reg, epcm->capture_bs_val); epcm->running = 1; epcm->first_ptr = 1; break; case SNDRV_PCM_TRIGGER_STOP: case SNDRV_PCM_TRIGGER_SUSPEND: epcm->running = 0; snd_emu10k1_intr_disable(emu, epcm->capture_inte); outl(epcm->capture_ipr, emu->port + IPR); - snd_emu10k1_ptr_write(emu, epcm->capture_bs_reg, 0, 0); + snd_emu10k1_ptr_write_raw(emu, epcm->capture_bs_reg, 0); switch (epcm->type) { case CAPTURE_AC97ADC: snd_emu10k1_ptr_write(emu, ADCCR, 0, 0); @@ -812,7 +812,7 @@ static snd_pcm_uframes_t snd_emu10k1_playback_pointer(struct snd_pcm_substream * if (!epcm->running) return 0; - ptr = snd_emu10k1_ptr_read(emu, CCCA, epcm->voices[0]->number) & 0x00ffffff; + ptr = snd_emu10k1_ptr_read(emu, CCCA_CURRADDR, epcm->voices[0]->number); #if 0 /* Perex's code */ ptr += runtime->buffer_size; ptr -= epcm->ccca_start_addr; @@ -899,7 +899,8 @@ static snd_pcm_uframes_t snd_emu10k1_capture_pointer(struct snd_pcm_substream *s udelay(50); /* hack, it takes awhile until capture is started */ epcm->first_ptr = 0; } - ptr = snd_emu10k1_ptr_read(emu, epcm->capture_idx_reg, 0) & 0x0000ffff; + ptr = REG_VAL_GET(FXIDX_IDX, // All *IDX_MASKs are assumed to be equal + snd_emu10k1_ptr_read_raw(emu, epcm->capture_idx_reg)); return bytes_to_frames(runtime, ptr); } @@ -1128,9 +1129,9 @@ static int snd_emu10k1_capture_open(struct snd_pcm_substream *substream) epcm->substream = substream; epcm->capture_ipr = IPR_ADCBUFFULL|IPR_ADCBUFHALFFULL; epcm->capture_inte = INTE_ADCBUFENABLE; - epcm->capture_ba_reg = ADCBA; - epcm->capture_bs_reg = ADCBS; - epcm->capture_idx_reg = emu->audigy ? A_ADCIDX : ADCIDX; + epcm->capture_ba_reg = REG_ADDR(ADCBA, 0); + epcm->capture_bs_reg = REG_ADDR(ADCBS, 0); + epcm->capture_idx_reg = emu->audigy ? REG_ADDR(A_ADCIDX, 0) : REG_ADDR(ADCIDX, 0); runtime->private_data = epcm; runtime->private_free = snd_emu10k1_pcm_free_substream; runtime->hw = snd_emu10k1_capture; @@ -1164,9 +1165,9 @@ static int snd_emu10k1_capture_mic_open(struct snd_pcm_substream *substream) epcm->substream = substream; epcm->capture_ipr = IPR_MICBUFFULL|IPR_MICBUFHALFFULL; epcm->capture_inte = INTE_MICBUFENABLE; - epcm->capture_ba_reg = MICBA; - epcm->capture_bs_reg = MICBS; - epcm->capture_idx_reg = emu->audigy ? A_MICIDX : MICIDX; + epcm->capture_ba_reg = REG_ADDR(MICBA, 0); + epcm->capture_bs_reg = REG_ADDR(MICBS, 0); + epcm->capture_idx_reg = emu->audigy ? REG_ADDR(A_MICIDX, 0) : REG_ADDR(MICIDX, 0); substream->runtime->private_data = epcm; substream->runtime->private_free = snd_emu10k1_pcm_free_substream; runtime->hw = snd_emu10k1_capture; @@ -1204,9 +1205,9 @@ static int snd_emu10k1_capture_efx_open(struct snd_pcm_substream *substream) epcm->substream = substream; epcm->capture_ipr = IPR_EFXBUFFULL|IPR_EFXBUFHALFFULL; epcm->capture_inte = INTE_EFXBUFENABLE; - epcm->capture_ba_reg = FXBA; - epcm->capture_bs_reg = FXBS; - epcm->capture_idx_reg = FXIDX; + epcm->capture_ba_reg = REG_ADDR(FXBA, 0); + epcm->capture_bs_reg = REG_ADDR(FXBS, 0); + epcm->capture_idx_reg = REG_ADDR(FXIDX, 0); substream->runtime->private_data = epcm; substream->runtime->private_free = snd_emu10k1_pcm_free_substream; runtime->hw = snd_emu10k1_capture_efx; @@ -1570,7 +1571,7 @@ static int snd_emu10k1_fx8010_playback_hw_free(struct snd_pcm_substream *substre unsigned int i; for (i = 0; i < pcm->channels; i++) - snd_emu10k1_ptr_write(emu, TANKMEMADDRREGBASE + 0x80 + pcm->etram[i], 0, 0); + snd_emu10k1_ptr_write_raw(emu, TANKMEMADDRREGBASE + 0x80 + pcm->etram[i], 0); return 0; } @@ -1592,14 +1593,16 @@ static int snd_emu10k1_fx8010_playback_prepare(struct snd_pcm_substream *substre pcm->pcm_rec.sw_buffer_size = snd_pcm_lib_buffer_bytes(substream); pcm->tram_pos = INITIAL_TRAM_POS(pcm->buffer_size); pcm->tram_shift = 0; - snd_emu10k1_ptr_write(emu, emu->gpr_base + pcm->gpr_running, 0, 0); /* reset */ - snd_emu10k1_ptr_write(emu, emu->gpr_base + pcm->gpr_trigger, 0, 0); /* reset */ - snd_emu10k1_ptr_write(emu, emu->gpr_base + pcm->gpr_size, 0, runtime->buffer_size); - snd_emu10k1_ptr_write(emu, emu->gpr_base + pcm->gpr_ptr, 0, 0); /* reset ptr number */ - snd_emu10k1_ptr_write(emu, emu->gpr_base + pcm->gpr_count, 0, runtime->period_size); - snd_emu10k1_ptr_write(emu, emu->gpr_base + pcm->gpr_tmpcount, 0, runtime->period_size); + snd_emu10k1_ptr_write_raw(emu, emu->gpr_base + pcm->gpr_running, 0); /* reset */ + snd_emu10k1_ptr_write_raw(emu, emu->gpr_base + pcm->gpr_trigger, 0); /* reset */ + snd_emu10k1_ptr_write_raw(emu, emu->gpr_base + pcm->gpr_size, runtime->buffer_size); + snd_emu10k1_ptr_write_raw(emu, emu->gpr_base + pcm->gpr_ptr, 0); /* reset ptr number */ + snd_emu10k1_ptr_write_raw(emu, emu->gpr_base + pcm->gpr_count, runtime->period_size); + snd_emu10k1_ptr_write_raw(emu, emu->gpr_base + pcm->gpr_tmpcount, runtime->period_size); for (i = 0; i < pcm->channels; i++) - snd_emu10k1_ptr_write(emu, TANKMEMADDRREGBASE + 0x80 + pcm->etram[i], 0, (TANKMEMADDRREG_READ|TANKMEMADDRREG_ALIGN) + i * (runtime->buffer_size / pcm->channels)); + snd_emu10k1_ptr_write_raw(emu, TANKMEMADDRREGBASE + 0x80 + pcm->etram[i], + (TANKMEMADDRREG_READ|TANKMEMADDRREG_ALIGN) + + i * (runtime->buffer_size / pcm->channels)); return 0; } @@ -1623,21 +1626,21 @@ static int snd_emu10k1_fx8010_playback_trigger(struct snd_pcm_substream *substre bits = SPCS_CLKACCY_1000PPM | SPCS_SAMPLERATE_48 | SPCS_CHANNELNUM_LEFT | SPCS_SOURCENUM_UNSPEC | SPCS_GENERATIONSTATUS | 0x00001200 | SPCS_EMPHASIS_NONE | SPCS_COPYRIGHT | SPCS_NOTAUDIODATA; - snd_emu10k1_ptr_write(emu, SPCS0 + i, 0, bits); + snd_emu10k1_ptr_write_raw(emu, SPCS0 + i, bits); } } #endif result = snd_emu10k1_fx8010_register_irq_handler(emu, snd_emu10k1_fx8010_playback_irq, pcm->gpr_running, substream, &pcm->irq); if (result < 0) goto __err; snd_emu10k1_fx8010_playback_transfer(substream); /* roll the ball */ - snd_emu10k1_ptr_write(emu, emu->gpr_base + pcm->gpr_trigger, 0, 1); + snd_emu10k1_ptr_write_raw(emu, emu->gpr_base + pcm->gpr_trigger, 1); break; case SNDRV_PCM_TRIGGER_STOP: case SNDRV_PCM_TRIGGER_PAUSE_PUSH: case SNDRV_PCM_TRIGGER_SUSPEND: snd_emu10k1_fx8010_unregister_irq_handler(emu, &pcm->irq); - snd_emu10k1_ptr_write(emu, emu->gpr_base + pcm->gpr_trigger, 0, 0); + snd_emu10k1_ptr_write_raw(emu, emu->gpr_base + pcm->gpr_trigger, 0); pcm->tram_pos = INITIAL_TRAM_POS(pcm->buffer_size); pcm->tram_shift = 0; break; @@ -1656,9 +1659,9 @@ static snd_pcm_uframes_t snd_emu10k1_fx8010_playback_pointer(struct snd_pcm_subs struct snd_emu10k1_fx8010_pcm *pcm = &emu->fx8010.pcm[substream->number]; size_t ptr; /* byte pointer */ - if (!snd_emu10k1_ptr_read(emu, emu->gpr_base + pcm->gpr_trigger, 0)) + if (!snd_emu10k1_ptr_read_raw(emu, emu->gpr_base + pcm->gpr_trigger)) return 0; - ptr = snd_emu10k1_ptr_read(emu, emu->gpr_base + pcm->gpr_ptr, 0) << 2; + ptr = snd_emu10k1_ptr_read_raw(emu, emu->gpr_base + pcm->gpr_ptr) << 2; return snd_pcm_indirect_playback_pointer(substream, &pcm->pcm_rec, ptr); } diff --git a/sound/pci/emu10k1/emuproc.c b/sound/pci/emu10k1/emuproc.c index bec72dc60a41..66a5862c3d1d 100644 --- a/sound/pci/emu10k1/emuproc.c +++ b/sound/pci/emu10k1/emuproc.c @@ -23,16 +23,16 @@ static void snd_emu10k1_proc_spdif_status(struct snd_emu10k1 * emu, struct snd_info_buffer *buffer, char *title, - int status_reg, - int rate_reg) + u8 status_reg, + u8 rate_reg) { static const char * const clkaccy[4] = { "1000ppm", "50ppm", "variable", "unknown" }; static const int samplerate[16] = { 44100, 1, 48000, 32000, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 }; static const char * const channel[16] = { "unspec", "left", "right", "3", "4", "5", "6", "7", "8", "9", "10", "11", "12", "13", "14", "15" }; static const char * const emphasis[8] = { "none", "50/15 usec 2 channel", "2", "3", "4", "5", "6", "7" }; unsigned int status, rate = 0; - status = snd_emu10k1_ptr_read(emu, status_reg, 0); + status = snd_emu10k1_ptr_read_raw(emu, status_reg); snd_iprintf(buffer, "\n%s\n", title); @@ -50,7 +50,7 @@ static void snd_emu10k1_proc_spdif_status(struct snd_emu10k1 * emu, snd_iprintf(buffer, "Clock Accuracy : %s\n", clkaccy[(status & SPCS_CLKACCYMASK) >> 28]); if (rate_reg > 0) { - rate = snd_emu10k1_ptr_read(emu, rate_reg, 0); + rate = snd_emu10k1_ptr_read_raw(emu, rate_reg); snd_iprintf(buffer, "S/PDIF Valid : %s\n", rate & SRCS_SPDIFVALID ? "on" : "off"); snd_iprintf(buffer, "S/PDIF Locked : %s\n", rate & SRCS_SPDIFLOCKED ? "on" : "off"); snd_iprintf(buffer, "Rate Locked : %s\n", rate & SRCS_RATELOCKED ? "on" : "off"); @@ -344,10 +344,10 @@ static ssize_t snd_emu10k1_fx8010_read(struct snd_info_entry *entry, return -ENOMEM; for (idx = 0; idx < ((pos & 3) + count + 3) >> 2; idx++) { unsigned int val; - val = snd_emu10k1_ptr_read(emu, offset + idx + (pos >> 2), 0); + val = snd_emu10k1_ptr_read_raw(emu, offset + idx + (pos >> 2)); if (tram_addr && emu->audigy) { val >>= 11; - val |= snd_emu10k1_ptr_read(emu, 0x100 + idx + (pos >> 2), 0) << 20; + val |= snd_emu10k1_ptr_read_raw(emu, 0x100 + idx + (pos >> 2)) << 20; } tmp[idx] = val; } diff --git a/sound/pci/emu10k1/io.c b/sound/pci/emu10k1/io.c index c60573f14ea8..6fa3cbb407d9 100644 --- a/sound/pci/emu10k1/io.c +++ b/sound/pci/emu10k1/io.c @@ -18,72 +18,62 @@ #include <linux/export.h> #include "p17v.h" -unsigned int snd_emu10k1_ptr_read(struct snd_emu10k1 * emu, unsigned int reg, unsigned int chn) +static inline bool check_ptr_reg(struct snd_emu10k1 *emu, u32 reg) { - unsigned long flags; - unsigned int regptr, val; - unsigned int mask; - - mask = emu->audigy ? A_PTR_ADDRESS_MASK : PTR_ADDRESS_MASK; - regptr = ((reg << 16) & mask) | (chn & PTR_CHANNELNUM_MASK); - - if (reg & 0xff000000) { - unsigned char size, offset; - - size = (reg >> 24) & 0x3f; - offset = (reg >> 16) & 0x1f; - mask = ((1 << size) - 1) << offset; - - spin_lock_irqsave(&emu->emu_lock, flags); - outl(regptr, emu->port + PTR); - val = inl(emu->port + DATA); - spin_unlock_irqrestore(&emu->emu_lock, flags); - - return (val & mask) >> offset; - } else { - spin_lock_irqsave(&emu->emu_lock, flags); - outl(regptr, emu->port + PTR); - val = inl(emu->port + DATA); - spin_unlock_irqrestore(&emu->emu_lock, flags); - return val; - } -} - -EXPORT_SYMBOL(snd_emu10k1_ptr_read); - -void snd_emu10k1_ptr_write(struct snd_emu10k1 *emu, unsigned int reg, unsigned int chn, unsigned int data) -{ - unsigned int regptr; - unsigned long flags; - unsigned int mask; - if (snd_BUG_ON(!emu)) - return; - mask = emu->audigy ? A_PTR_ADDRESS_MASK : PTR_ADDRESS_MASK; - regptr = ((reg << 16) & mask) | (chn & PTR_CHANNELNUM_MASK); - - if (reg & 0xff000000) { - unsigned char size, offset; - - size = (reg >> 24) & 0x3f; - offset = (reg >> 16) & 0x1f; - mask = ((1 << size) - 1) << offset; - data = (data << offset) & mask; - - spin_lock_irqsave(&emu->emu_lock, flags); - outl(regptr, emu->port + PTR); - data |= inl(emu->port + DATA) & ~mask; - outl(data, emu->port + DATA); - spin_unlock_irqrestore(&emu->emu_lock, flags); - } else { - spin_lock_irqsave(&emu->emu_lock, flags); - outl(regptr, emu->port + PTR); - outl(data, emu->port + DATA); - spin_unlock_irqrestore(&emu->emu_lock, flags); - } + return false; + if (snd_BUG_ON(reg & 0xffff0000 & (emu->audigy ? ~A_PTR_ADDRESS_MASK : ~PTR_ADDRESS_MASK))) + return false; + if (snd_BUG_ON(reg & 0xffff & ~PTR_CHANNELNUM_MASK)) + return false; + return true; } -EXPORT_SYMBOL(snd_emu10k1_ptr_write); +unsigned int snd_emu10k1_ptr_read_raw(struct snd_emu10k1 *emu, u32 reg) +{ + unsigned long flags; + u32 val; + + if (!check_ptr_reg(emu, reg)) + return 0; + + spin_lock_irqsave(&emu->emu_lock, flags); + outl(reg, emu->port + PTR); + val = inl(emu->port + DATA); + spin_unlock_irqrestore(&emu->emu_lock, flags); + return val; +} +EXPORT_SYMBOL(snd_emu10k1_ptr_read_raw); + +void snd_emu10k1_ptr_write_raw(struct snd_emu10k1 *emu, u32 reg, u32 data) +{ + unsigned long flags; + + if (!check_ptr_reg(emu, reg)) + return; + + spin_lock_irqsave(&emu->emu_lock, flags); + outl(reg, emu->port + PTR); + outl(data, emu->port + DATA); + spin_unlock_irqrestore(&emu->emu_lock, flags); +} +EXPORT_SYMBOL(snd_emu10k1_ptr_write_raw); + +void snd_emu10k1_ptr_modify(struct snd_emu10k1 *emu, u32 reg, u32 and_mask, u32 or_mask) +{ + unsigned long flags; + + if (!check_ptr_reg(emu, reg)) + return; + + spin_lock_irqsave(&emu->emu_lock, flags); + outl(reg, emu->port + PTR); + or_mask |= inl(emu->port + DATA) & and_mask; + outl(or_mask, emu->port + DATA); + spin_unlock_irqrestore(&emu->emu_lock, flags); +} + +EXPORT_SYMBOL(snd_emu10k1_ptr_modify); unsigned int snd_emu10k1_ptr20_read(struct snd_emu10k1 * emu, unsigned int reg, -- 2.40.0.152.g15d061e6df

2 1

[PATCH] ALSA: emu10k1: macro-ize snd_emu10k1_ptr_{read,write}()
by Oswald Buddenhagen 08 May '23

08 May '23

The idea to encode the bitfield manipulation in the register address is quite clever, but it's somewhat wasteful to do these calculations at runtime, given that they are all constants. Change that. The added bitfield manipulation macros will be used separately as well. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- include/sound/emu10k1.h | 29 ++++++++- sound/pci/emu10k1/emupcm.c | 31 +++++----- sound/pci/emu10k1/emuproc.c | 4 +- sound/pci/emu10k1/io.c | 116 +++++++++++++++++------------------- 4 files changed, 99 insertions(+), 81 deletions(-) diff --git a/include/sound/emu10k1.h b/include/sound/emu10k1.h index 8fe80dcee71b..fd1fe49578ce 100644 --- a/include/sound/emu10k1.h +++ b/include/sound/emu10k1.h @@ -1773,8 +1773,33 @@ int snd_emu10k1_fx8010_tram_setup(struct snd_emu10k1 *emu, u32 size); int snd_emu10k1_done(struct snd_emu10k1 * emu); /* I/O functions */ -unsigned int snd_emu10k1_ptr_read(struct snd_emu10k1 * emu, unsigned int reg, unsigned int chn); -void snd_emu10k1_ptr_write(struct snd_emu10k1 *emu, unsigned int reg, unsigned int chn, unsigned int data); + +#define REG_SHIFT(r) (((r) >> 16) & 0x1f) +#define REG_SIZE(r) (((r) >> 24) & 0x1f) +#define REG_MASK0(r) ((1U << REG_SIZE(r)) - 1U) +#define REG_MASK(r) (REG_MASK0(r) << REG_SHIFT(r)) +#define REG_ADDR(r, v) ((((r) & 0xffff) << 16) | (v)) +#define REG_VAL_GET(r, v) ((v & REG_MASK(r)) >> REG_SHIFT(r)) +#define REG_VAL_PUT(r, v) ((v) << REG_SHIFT(r)) +#define snd_emu10k1_ptr_read(emu, reg, voice) \ + ({ \ + u32 data = snd_emu10k1_ptr_read_raw(emu, REG_ADDR(reg, voice)); \ + if (REG_SIZE(reg)) \ + data = REG_VAL_GET(reg, data); \ + data; \ + }) +#define snd_emu10k1_ptr_write(emu, reg, voice, data) \ + do { \ + if (REG_SIZE(reg)) \ + snd_emu10k1_ptr_modify(emu, REG_ADDR(reg, voice), \ + ~REG_MASK(reg), REG_VAL_PUT(reg, data)); \ + else \ + snd_emu10k1_ptr_write_raw(emu, REG_ADDR(reg, voice), data); \ + } while (0) + +u32 snd_emu10k1_ptr_read_raw(struct snd_emu10k1 *emu, u32 reg); +void snd_emu10k1_ptr_write_raw(struct snd_emu10k1 *emu, u32 reg, u32 data); +void snd_emu10k1_ptr_modify(struct snd_emu10k1 *emu, u32 reg, u32 and_mask, u32 or_mask); unsigned int snd_emu10k1_ptr20_read(struct snd_emu10k1 * emu, unsigned int reg, unsigned int chn); void snd_emu10k1_ptr20_write(struct snd_emu10k1 *emu, unsigned int reg, unsigned int chn, unsigned int data); int snd_emu10k1_spi_write(struct snd_emu10k1 * emu, unsigned int data); diff --git a/sound/pci/emu10k1/emupcm.c b/sound/pci/emu10k1/emupcm.c index b0c0ef342756..2baa7f01eb5b 100644 --- a/sound/pci/emu10k1/emupcm.c +++ b/sound/pci/emu10k1/emupcm.c @@ -528,7 +528,7 @@ static int snd_emu10k1_capture_prepare(struct snd_pcm_substream *substream) int idx; /* zeroing the buffer size will stop capture */ - snd_emu10k1_ptr_write(emu, epcm->capture_bs_reg, 0, 0); + snd_emu10k1_ptr_write_raw(emu, epcm->capture_bs_reg, 0); switch (epcm->type) { case CAPTURE_AC97ADC: snd_emu10k1_ptr_write(emu, ADCCR, 0, 0); @@ -543,7 +543,7 @@ static int snd_emu10k1_capture_prepare(struct snd_pcm_substream *substream) default: break; } - snd_emu10k1_ptr_write(emu, epcm->capture_ba_reg, 0, runtime->dma_addr); + snd_emu10k1_ptr_write_raw(emu, epcm->capture_ba_reg, runtime->dma_addr); epcm->capture_bufsize = snd_pcm_lib_buffer_bytes(substream); epcm->capture_bs_val = 0; for (idx = 0; idx < 31; idx++) { @@ -771,16 +771,16 @@ static int snd_emu10k1_capture_trigger(struct snd_pcm_substream *substream, default: break; } - snd_emu10k1_ptr_write(emu, epcm->capture_bs_reg, 0, epcm->capture_bs_val); + snd_emu10k1_ptr_write_raw(emu, epcm->capture_bs_reg, epcm->capture_bs_val); epcm->running = 1; epcm->first_ptr = 1; break; case SNDRV_PCM_TRIGGER_STOP: case SNDRV_PCM_TRIGGER_SUSPEND: epcm->running = 0; snd_emu10k1_intr_disable(emu, epcm->capture_inte); outl(epcm->capture_ipr, emu->port + IPR); - snd_emu10k1_ptr_write(emu, epcm->capture_bs_reg, 0, 0); + snd_emu10k1_ptr_write_raw(emu, epcm->capture_bs_reg, 0); switch (epcm->type) { case CAPTURE_AC97ADC: snd_emu10k1_ptr_write(emu, ADCCR, 0, 0); @@ -812,7 +812,7 @@ static snd_pcm_uframes_t snd_emu10k1_playback_pointer(struct snd_pcm_substream * if (!epcm->running) return 0; - ptr = snd_emu10k1_ptr_read(emu, CCCA, epcm->voices[0]->number) & 0x00ffffff; + ptr = snd_emu10k1_ptr_read(emu, CCCA_CURRADDR, epcm->voices[0]->number); #if 0 /* Perex's code */ ptr += runtime->buffer_size; ptr -= epcm->ccca_start_addr; @@ -899,7 +899,8 @@ static snd_pcm_uframes_t snd_emu10k1_capture_pointer(struct snd_pcm_substream *s udelay(50); /* hack, it takes awhile until capture is started */ epcm->first_ptr = 0; } - ptr = snd_emu10k1_ptr_read(emu, epcm->capture_idx_reg, 0) & 0x0000ffff; + ptr = REG_VAL_GET(FXIDX_IDX, // All *IDX_MASKs are assumed to be equal + snd_emu10k1_ptr_read_raw(emu, epcm->capture_idx_reg)); return bytes_to_frames(runtime, ptr); } @@ -1128,9 +1129,9 @@ static int snd_emu10k1_capture_open(struct snd_pcm_substream *substream) epcm->substream = substream; epcm->capture_ipr = IPR_ADCBUFFULL|IPR_ADCBUFHALFFULL; epcm->capture_inte = INTE_ADCBUFENABLE; - epcm->capture_ba_reg = ADCBA; - epcm->capture_bs_reg = ADCBS; - epcm->capture_idx_reg = emu->audigy ? A_ADCIDX : ADCIDX; + epcm->capture_ba_reg = REG_ADDR(ADCBA, 0); + epcm->capture_bs_reg = REG_ADDR(ADCBS, 0); + epcm->capture_idx_reg = emu->audigy ? REG_ADDR(A_ADCIDX, 0) : REG_ADDR(ADCIDX, 0); runtime->private_data = epcm; runtime->private_free = snd_emu10k1_pcm_free_substream; runtime->hw = snd_emu10k1_capture; @@ -1164,9 +1165,9 @@ static int snd_emu10k1_capture_mic_open(struct snd_pcm_substream *substream) epcm->substream = substream; epcm->capture_ipr = IPR_MICBUFFULL|IPR_MICBUFHALFFULL; epcm->capture_inte = INTE_MICBUFENABLE; - epcm->capture_ba_reg = MICBA; - epcm->capture_bs_reg = MICBS; - epcm->capture_idx_reg = emu->audigy ? A_MICIDX : MICIDX; + epcm->capture_ba_reg = REG_ADDR(MICBA, 0); + epcm->capture_bs_reg = REG_ADDR(MICBS, 0); + epcm->capture_idx_reg = emu->audigy ? REG_ADDR(A_MICIDX, 0) : REG_ADDR(MICIDX, 0); substream->runtime->private_data = epcm; substream->runtime->private_free = snd_emu10k1_pcm_free_substream; runtime->hw = snd_emu10k1_capture; @@ -1204,9 +1205,9 @@ static int snd_emu10k1_capture_efx_open(struct snd_pcm_substream *substream) epcm->substream = substream; epcm->capture_ipr = IPR_EFXBUFFULL|IPR_EFXBUFHALFFULL; epcm->capture_inte = INTE_EFXBUFENABLE; - epcm->capture_ba_reg = FXBA; - epcm->capture_bs_reg = FXBS; - epcm->capture_idx_reg = FXIDX; + epcm->capture_ba_reg = REG_ADDR(FXBA, 0); + epcm->capture_bs_reg = REG_ADDR(FXBS, 0); + epcm->capture_idx_reg = REG_ADDR(FXIDX, 0); substream->runtime->private_data = epcm; substream->runtime->private_free = snd_emu10k1_pcm_free_substream; runtime->hw = snd_emu10k1_capture_efx; diff --git a/sound/pci/emu10k1/emuproc.c b/sound/pci/emu10k1/emuproc.c index bec72dc60a41..3a7f60d64c27 100644 --- a/sound/pci/emu10k1/emuproc.c +++ b/sound/pci/emu10k1/emuproc.c @@ -23,8 +23,8 @@ static void snd_emu10k1_proc_spdif_status(struct snd_emu10k1 * emu, struct snd_info_buffer *buffer, char *title, - int status_reg, - int rate_reg) + u8 status_reg, + u8 rate_reg) { static const char * const clkaccy[4] = { "1000ppm", "50ppm", "variable", "unknown" }; static const int samplerate[16] = { 44100, 1, 48000, 32000, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 }; diff --git a/sound/pci/emu10k1/io.c b/sound/pci/emu10k1/io.c index c60573f14ea8..373c633bd88b 100644 --- a/sound/pci/emu10k1/io.c +++ b/sound/pci/emu10k1/io.c @@ -18,72 +18,64 @@ #include <linux/export.h> #include "p17v.h" -unsigned int snd_emu10k1_ptr_read(struct snd_emu10k1 * emu, unsigned int reg, unsigned int chn) +static inline int check_ptr_reg(struct snd_emu10k1 *emu, u32 reg) { - unsigned long flags; - unsigned int regptr, val; - unsigned int mask; - - mask = emu->audigy ? A_PTR_ADDRESS_MASK : PTR_ADDRESS_MASK; - regptr = ((reg << 16) & mask) | (chn & PTR_CHANNELNUM_MASK); - - if (reg & 0xff000000) { - unsigned char size, offset; - - size = (reg >> 24) & 0x3f; - offset = (reg >> 16) & 0x1f; - mask = ((1 << size) - 1) << offset; - - spin_lock_irqsave(&emu->emu_lock, flags); - outl(regptr, emu->port + PTR); - val = inl(emu->port + DATA); - spin_unlock_irqrestore(&emu->emu_lock, flags); - - return (val & mask) >> offset; - } else { - spin_lock_irqsave(&emu->emu_lock, flags); - outl(regptr, emu->port + PTR); - val = inl(emu->port + DATA); - spin_unlock_irqrestore(&emu->emu_lock, flags); - return val; - } -} - -EXPORT_SYMBOL(snd_emu10k1_ptr_read); - -void snd_emu10k1_ptr_write(struct snd_emu10k1 *emu, unsigned int reg, unsigned int chn, unsigned int data) -{ - unsigned int regptr; - unsigned long flags; - unsigned int mask; - if (snd_BUG_ON(!emu)) - return; - mask = emu->audigy ? A_PTR_ADDRESS_MASK : PTR_ADDRESS_MASK; - regptr = ((reg << 16) & mask) | (chn & PTR_CHANNELNUM_MASK); - - if (reg & 0xff000000) { - unsigned char size, offset; - - size = (reg >> 24) & 0x3f; - offset = (reg >> 16) & 0x1f; - mask = ((1 << size) - 1) << offset; - data = (data << offset) & mask; - - spin_lock_irqsave(&emu->emu_lock, flags); - outl(regptr, emu->port + PTR); - data |= inl(emu->port + DATA) & ~mask; - outl(data, emu->port + DATA); - spin_unlock_irqrestore(&emu->emu_lock, flags); - } else { - spin_lock_irqsave(&emu->emu_lock, flags); - outl(regptr, emu->port + PTR); - outl(data, emu->port + DATA); - spin_unlock_irqrestore(&emu->emu_lock, flags); - } + return 0; + if (snd_BUG_ON(reg & 0xffff0000 & (emu->audigy ? ~A_PTR_ADDRESS_MASK : ~PTR_ADDRESS_MASK))) + return 0; + if (snd_BUG_ON(reg & 0xffff & ~PTR_CHANNELNUM_MASK)) + return 0; + return 1; } -EXPORT_SYMBOL(snd_emu10k1_ptr_write); +unsigned int snd_emu10k1_ptr_read_raw(struct snd_emu10k1 *emu, u32 reg) +{ + unsigned long flags; + u32 val; + + if (!check_ptr_reg(emu, reg)) + return 0; + + spin_lock_irqsave(&emu->emu_lock, flags); + outl(reg, emu->port + PTR); + val = inl(emu->port + DATA); + spin_unlock_irqrestore(&emu->emu_lock, flags); + return val; +} + +EXPORT_SYMBOL(snd_emu10k1_ptr_read_raw); + +void snd_emu10k1_ptr_write_raw(struct snd_emu10k1 *emu, u32 reg, u32 data) +{ + unsigned long flags; + + if (!check_ptr_reg(emu, reg)) + return; + + spin_lock_irqsave(&emu->emu_lock, flags); + outl(reg, emu->port + PTR); + outl(data, emu->port + DATA); + spin_unlock_irqrestore(&emu->emu_lock, flags); +} + +EXPORT_SYMBOL(snd_emu10k1_ptr_write_raw); + +void snd_emu10k1_ptr_modify(struct snd_emu10k1 *emu, u32 reg, u32 and_mask, u32 or_mask) +{ + unsigned long flags; + + if (!check_ptr_reg(emu, reg)) + return; + + spin_lock_irqsave(&emu->emu_lock, flags); + outl(reg, emu->port + PTR); + or_mask |= inl(emu->port + DATA) & and_mask; + outl(or_mask, emu->port + DATA); + spin_unlock_irqrestore(&emu->emu_lock, flags); +} + +EXPORT_SYMBOL(snd_emu10k1_ptr_modify); unsigned int snd_emu10k1_ptr20_read(struct snd_emu10k1 * emu, unsigned int reg, -- 2.40.0.152.g15d061e6df

2 4

[PATCH 5.15 058/371] sound/oss/dmasound: fix build when drivers are mixed =y/=m
by Greg Kroah-Hartman 08 May '23

08 May '23

From: Randy Dunlap <rdunlap(a)infradead.org> commit 9dd7c46346ca4390f84a7ea9933005eb1b175c15 upstream. When CONFIG_DMASOUND_ATARI=m and CONFIG_DMASOUND_Q40=y (or vice versa), dmasound_core.o can be built without dmasound_deinit() being defined, causing a build error: ERROR: modpost: "dmasound_deinit" [sound/oss/dmasound/dmasound_atari.ko] undefined! Modify dmasound_core.c and dmasound.h so that dmasound_deinit() is always available. The mixed modes (=y/=m) also mean that several variables and structs have to be declared in all cases. Suggested-by: Arnd Bergmann <arnd(a)arndb.de> Suggested-by: Geert Uytterhoeven <geert(a)linux-m68k.org> Signed-off-by: Randy Dunlap <rdunlap(a)infradead.org> Reported-by: kernel test robot <lkp(a)intel.com> Link: lore.kernel.org/r/202204032138.EFT9qGEd-lkp@intel.com Cc: Geert Uytterhoeven <geert(a)linux-m68k.org> Cc: Jaroslav Kysela <perex(a)perex.cz> Cc: Takashi Iwai <tiwai(a)suse.com> Cc: alsa-devel(a)alsa-project.org Link: https://lore.kernel.org/r/20220405234118.24830-1-rdunlap@infradead.org Signed-off-by: Takashi Iwai <tiwai(a)suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- sound/oss/dmasound/dmasound.h | 6 ------ sound/oss/dmasound/dmasound_core.c | 24 +----------------------- 2 files changed, 1 insertion(+), 29 deletions(-) --- a/sound/oss/dmasound/dmasound.h +++ b/sound/oss/dmasound/dmasound.h @@ -88,11 +88,7 @@ static inline int ioctl_return(int __use */ extern int dmasound_init(void); -#ifdef MODULE extern void dmasound_deinit(void); -#else -#define dmasound_deinit() do { } while (0) -#endif /* description of the set-up applies to either hard or soft settings */ @@ -114,9 +110,7 @@ typedef struct { void *(*dma_alloc)(unsigned int, gfp_t); void (*dma_free)(void *, unsigned int); int (*irqinit)(void); -#ifdef MODULE void (*irqcleanup)(void); -#endif void (*init)(void); void (*silence)(void); int (*setFormat)(int); --- a/sound/oss/dmasound/dmasound_core.c +++ b/sound/oss/dmasound/dmasound_core.c @@ -206,12 +206,10 @@ module_param(writeBufSize, int, 0); MODULE_LICENSE("GPL"); -#ifdef MODULE static int sq_unit = -1; static int mixer_unit = -1; static int state_unit = -1; static int irq_installed; -#endif /* MODULE */ /* control over who can modify resources shared between play/record */ static fmode_t shared_resource_owner; @@ -391,9 +389,6 @@ static const struct file_operations mixe static void mixer_init(void) { -#ifndef MODULE - int mixer_unit; -#endif mixer_unit = register_sound_mixer(&mixer_fops, -1); if (mixer_unit < 0) return; @@ -1171,9 +1166,6 @@ static const struct file_operations sq_f static int sq_init(void) { const struct file_operations *fops = &sq_fops; -#ifndef MODULE - int sq_unit; -#endif sq_unit = register_sound_dsp(fops, -1); if (sq_unit < 0) { @@ -1366,9 +1358,6 @@ static const struct file_operations stat static int state_init(void) { -#ifndef MODULE - int state_unit; -#endif state_unit = register_sound_special(&state_fops, SND_DEV_STATUS); if (state_unit < 0) return state_unit ; @@ -1386,10 +1375,9 @@ static int state_init(void) int dmasound_init(void) { int res ; -#ifdef MODULE + if (irq_installed) return -EBUSY; -#endif /* Set up sound queue, /dev/audio and /dev/dsp. */ @@ -1408,9 +1396,7 @@ int dmasound_init(void) printk(KERN_ERR "DMA sound driver: Interrupt initialization failed\n"); return -ENODEV; } -#ifdef MODULE irq_installed = 1; -#endif printk(KERN_INFO "%s DMA sound driver rev %03d installed\n", dmasound.mach.name, (DMASOUND_CORE_REVISION<<4) + @@ -1424,8 +1410,6 @@ int dmasound_init(void) return 0; } -#ifdef MODULE - void dmasound_deinit(void) { if (irq_installed) { @@ -1444,8 +1428,6 @@ void dmasound_deinit(void) unregister_sound_dsp(sq_unit); } -#else /* !MODULE */ - static int dmasound_setup(char *str) { int ints[6], size; @@ -1489,8 +1471,6 @@ static int dmasound_setup(char *str) __setup("dmasound=", dmasound_setup); -#endif /* !MODULE */ - /* * Conversion tables */ @@ -1577,9 +1557,7 @@ char dmasound_alaw2dma8[] = { EXPORT_SYMBOL(dmasound); EXPORT_SYMBOL(dmasound_init); -#ifdef MODULE EXPORT_SYMBOL(dmasound_deinit); -#endif EXPORT_SYMBOL(dmasound_write_sq); EXPORT_SYMBOL(dmasound_catchRadius); #ifdef HAS_8BIT_TABLES

1 0

[PATCH] Sound:last.c: fix code syle trailing white space - modify printk()->netdev_dbg() - Possible unnecessary KERN_INFO removed
by jack1989s＠gmail.com 08 May '23

08 May '23

From: Federico Di Lembo <jack1989s(a)gmail.com> Fixing coding style. Signed-off-by: Federico Di Lembo <jack1989s(a)gmail.com> --- sound/last.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/sound/last.c b/sound/last.c index f0bb98780e70..b8cfd6ded95d 100644 --- a/sound/last.c +++ b/sound/last.c @@ -11,18 +11,18 @@ static int __init alsa_sound_last_init(void) { struct snd_card *card; int idx, ok = 0; - - printk(KERN_INFO "ALSA device list:\n"); + + netdev_dbg("ALSA device list:\n"); for (idx = 0; idx < SNDRV_CARDS; idx++) { card = snd_card_ref(idx); if (card) { - printk(KERN_INFO " #%i: %s\n", idx, card->longname); + netdev_dbg(" #%i: %s\n", idx, card->longname); snd_card_unref(card); ok++; } } if (ok == 0) - printk(KERN_INFO " No soundcards found.\n"); + netdev_dbg(" No soundcards found.\n"); return 0; } -- 2.34.1

3 2

[PATCH] ALSA: emu10k1: minor E-MU naming fixups
by Oswald Buddenhagen 08 May '23

08 May '23

- Fix mixer source port names. These will require some users to re-adjust their mixer settings, which seems acceptable: - The S/PDIF port is on the main 1010 card, not the 0202 daughter card - The 1616m CardBus card has all inputs on the dock, so there is no point in specifying it - Conversely, the 1010 card has "dispersed" inputs, so say where the ADAT port is, consistently with the S/PDIF port - The 1616m CardBus card is actually named E-MU 02 (due to the headphone output jack it has) - Fix capitalization of "E-MU" Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- sound/pci/emu10k1/emu10k1_main.c | 16 +++++++------- sound/pci/emu10k1/emumixer.c | 36 ++++++++++++++++---------------- 2 files changed, 26 insertions(+), 26 deletions(-) diff --git a/sound/pci/emu10k1/emu10k1_main.c b/sound/pci/emu10k1/emu10k1_main.c index 3abdaf1b9624..5d9d772e3a13 100644 --- a/sound/pci/emu10k1/emu10k1_main.c +++ b/sound/pci/emu10k1/emu10k1_main.c @@ -1310,7 +1310,7 @@ static const struct snd_emu_chip_details emu_chip_details[] = { /* Does NOT support sync daughter card (obviously). */ /* Tested by James(a)superbug.co.uk 4th Nov 2007. */ {.vendor = 0x1102, .device = 0x0008, .subsystem = 0x42011102, - .driver = "Audigy2", .name = "E-mu 1010 Notebook [MAEM8950]", + .driver = "Audigy2", .name = "E-MU 02 CardBus [MAEM8950]", .id = "EMU1010", .emu10k2_chip = 1, .ca0108_chip = 1, @@ -1323,7 +1323,7 @@ static const struct snd_emu_chip_details emu_chip_details[] = { * MicroDock[M] to make it an E-MU 1616[m]. */ /* Does NOT support sync daughter card. */ {.vendor = 0x1102, .device = 0x0008, .subsystem = 0x40041102, - .driver = "Audigy2", .name = "E-mu 1010b PCI [MAEM8960]", + .driver = "Audigy2", .name = "E-MU 1010b PCI [MAEM8960]", .id = "EMU1010", .emu10k2_chip = 1, .ca0108_chip = 1, @@ -1337,48 +1337,48 @@ static const struct snd_emu_chip_details emu_chip_details[] = { * still work. */ /* Does NOT support sync daughter card. */ {.vendor = 0x1102, .device = 0x0008, .subsystem = 0x40071102, - .driver = "Audigy2", .name = "E-mu 1010 PCIe [MAEM8986]", + .driver = "Audigy2", .name = "E-MU 1010 PCIe [MAEM8986]", .id = "EMU1010", .emu10k2_chip = 1, .ca0108_chip = 1, .spk71 = 1, .emu_model = EMU_MODEL_EMU1010B}, /* EMU 1010 PCIe */ /* Tested by James(a)superbug.co.uk 8th July 2005. */ /* This is MAEM8810 "Hana", 0202 is MAEM8820 "Hamoa" */ /* Attach 0202 daughter card to make it an E-MU 1212m, OR an * AudioDock[M] to make it an E-MU 1820[m]. */ /* Supports sync daughter card. */ {.vendor = 0x1102, .device = 0x0004, .subsystem = 0x40011102, - .driver = "Audigy2", .name = "E-mu 1010 [MAEM8810]", + .driver = "Audigy2", .name = "E-MU 1010 [MAEM8810]", .id = "EMU1010", .emu10k2_chip = 1, .ca0102_chip = 1, .spk71 = 1, .emu_model = EMU_MODEL_EMU1010}, /* EMU 1010 old revision */ /* This is MAEM8852 "HanaLiteLite" */ /* Supports sync daughter card. */ /* Tested by oswald.buddenhagen(a)gmx.de Mar 2023. */ {.vendor = 0x1102, .device = 0x0008, .subsystem = 0x40021102, - .driver = "Audigy2", .name = "E-mu 0404b PCI [MAEM8852]", + .driver = "Audigy2", .name = "E-MU 0404b PCI [MAEM8852]", .id = "EMU0404", .emu10k2_chip = 1, .ca0108_chip = 1, .spk71 = 1, .emu_model = EMU_MODEL_EMU0404}, /* EMU 0404 new revision */ /* This is MAEM8850 "HanaLite" */ /* Supports sync daughter card. */ /* Tested by James(a)superbug.co.uk 20-3-2007. */ {.vendor = 0x1102, .device = 0x0004, .subsystem = 0x40021102, - .driver = "Audigy2", .name = "E-mu 0404 [MAEM8850]", + .driver = "Audigy2", .name = "E-MU 0404 [MAEM8850]", .id = "EMU0404", .emu10k2_chip = 1, .ca0102_chip = 1, .spk71 = 1, .emu_model = EMU_MODEL_EMU0404}, /* EMU 0404 */ /* EMU0404 PCIe */ /* Does NOT support sync daughter card. */ {.vendor = 0x1102, .device = 0x0008, .subsystem = 0x40051102, - .driver = "Audigy2", .name = "E-mu 0404 PCIe [MAEM8984]", + .driver = "Audigy2", .name = "E-MU 0404 PCIe [MAEM8984]", .id = "EMU0404", .emu10k2_chip = 1, .ca0108_chip = 1, @@ -1645,7 +1645,7 @@ static const struct snd_emu_chip_details emu_chip_details[] = { .ac97_chip = 1, .sblive51 = 1} , {.vendor = 0x1102, .device = 0x0002, .subsystem = 0x40011102, - .driver = "EMU10K1", .name = "E-mu APS [PC545]", + .driver = "EMU10K1", .name = "E-MU APS [PC545]", .id = "APS", .emu10k1_chip = 1, .ecard = 1} , diff --git a/sound/pci/emu10k1/emumixer.c b/sound/pci/emu10k1/emumixer.c index 8fce3413f4ae..a101fe7598c4 100644 --- a/sound/pci/emu10k1/emumixer.c +++ b/sound/pci/emu10k1/emumixer.c @@ -81,16 +81,16 @@ static const char * const emu1010_src_texts[] = { "Dock ADC3 Right", "0202 ADC Left", "0202 ADC Right", - "0202 SPDIF Left", - "0202 SPDIF Right", - "ADAT 0", - "ADAT 1", - "ADAT 2", - "ADAT 3", - "ADAT 4", - "ADAT 5", - "ADAT 6", - "ADAT 7", + "1010 SPDIF Left", + "1010 SPDIF Right", + "1010 ADAT 0", + "1010 ADAT 1", + "1010 ADAT 2", + "1010 ADAT 3", + "1010 ADAT 4", + "1010 ADAT 5", + "1010 ADAT 6", + "1010 ADAT 7", "DSP 0", "DSP 1", "DSP 2", @@ -129,14 +129,14 @@ static const char * const emu1010_src_texts[] = { static const char * const emu1616_src_texts[] = { "Silence", - "Dock Mic A", - "Dock Mic B", - "Dock ADC1 Left", - "Dock ADC1 Right", - "Dock ADC2 Left", - "Dock ADC2 Right", - "Dock SPDIF Left", - "Dock SPDIF Right", + "Mic A", + "Mic B", + "ADC1 Left", + "ADC1 Right", + "ADC2 Left", + "ADC2 Right", + "SPDIF Left", + "SPDIF Right", "ADAT 0", "ADAT 1", "ADAT 2", -- 2.40.0.152.g15d061e6df

2 1

[PATCH 0/6] ALSA: emu10k1: Various improvements related to locking
by Oswald Buddenhagen 08 May '23

08 May '23

--- This patch series needs to be applied on top of the patch titled "ALSA: emu10k1: use more existing defines instead of open-coded numbers". Oswald Buddenhagen (6): ALSA: emu10k1: remove pointless locks from timer code ALSA: emu10k1: remove pointless locks from /proc code ALSA: emu10k1: use the right lock in snd_emu10k1_shared_spdif_put() ALSA: emu10k1: fix locking in snd_emu1010_fpga_link_dst_src_write() ALSA: core: update comment on snd_card.controls_rwsem ALSA: emu10k1: remove now superfluous mixer locking include/sound/core.h | 2 +- sound/pci/emu10k1/emufx.c | 7 ------- sound/pci/emu10k1/emumixer.c | 32 ++------------------------------ sound/pci/emu10k1/emupcm.c | 2 -- sound/pci/emu10k1/emuproc.c | 6 ------ sound/pci/emu10k1/io.c | 25 +++++++++++++++++-------- sound/pci/emu10k1/timer.c | 6 ------ 7 files changed, 20 insertions(+), 60 deletions(-) -- 2.40.0.152.g15d061e6df

2 7

[PATCH v2] soundwire: bus: Don't filter slave alerts
by Charles Keepax 08 May '23

08 May '23

It makes sense to have only a single point responsible for ensuring that all currently pending IRQs are handled. The current code in sdw_handle_slave_alerts confusingly splits this process in two. This code will loop until the asserted IRQs are cleared but it will only handle IRQs that were already asserted when it was called. This means the caller must also loop (either manually, or through its IRQ mechanism) until the IRQs are all handled. It makes sense to either do all the looping in sdw_handle_slave_alerts or do no looping there and let the host controller repeatedly call it until things are handled. There are realistically two sensible host controllers, those that will generate an IRQ when the alert status changes and those that will generate an IRQ continuously whilst the alert status is high. The current code will work fine for the second of those systems but not the first with out additional looping in the host controller. Removing the code that filters out new IRQs whilst the handler is running enables both types of host controller to be supported and simplifies the code. The code will still only loop up to SDW_READ_INTR_CLEAR_RETRY times, so it shouldn't be possible for it to get completely stuck handling IRQs forever, and if you are generating IRQs faster than you can handle them you likely have bigger problems anyway. This fixes an issue on the Cadence SoundWire IP, which only generates IRQs on an alert status change, where an alert which arrives whilst another alert is being handled will never be handled and will block all future alerts from being handled. Signed-off-by: Charles Keepax <ckeepax(a)opensource.cirrus.com> --- Changes since v1: - Update commit message Thanks, Charles drivers/soundwire/bus.c | 12 ++++-------- 1 file changed, 4 insertions(+), 8 deletions(-) diff --git a/drivers/soundwire/bus.c b/drivers/soundwire/bus.c index 1ea6a64f8c4a5..338f4f0b5d0cc 100644 --- a/drivers/soundwire/bus.c +++ b/drivers/soundwire/bus.c @@ -1588,7 +1588,7 @@ static int sdw_handle_slave_alerts(struct sdw_slave *slave) unsigned long port; bool slave_notify; u8 sdca_cascade = 0; - u8 buf, buf2[2], _buf, _buf2[2]; + u8 buf, buf2[2]; bool parity_check; bool parity_quirk; @@ -1745,9 +1745,9 @@ static int sdw_handle_slave_alerts(struct sdw_slave *slave) "SDW_SCP_INT1 recheck read failed:%d\n", ret); goto io_err; } - _buf = ret; + buf = ret; - ret = sdw_nread_no_pm(slave, SDW_SCP_INTSTAT2, 2, _buf2); + ret = sdw_nread_no_pm(slave, SDW_SCP_INTSTAT2, 2, buf2); if (ret < 0) { dev_err(&slave->dev, "SDW_SCP_INT2/3 recheck read failed:%d\n", ret); @@ -1765,12 +1765,8 @@ static int sdw_handle_slave_alerts(struct sdw_slave *slave) } /* - * Make sure no interrupts are pending, but filter to limit loop - * to interrupts identified in the first status read + * Make sure no interrupts are pending */ - buf &= _buf; - buf2[0] &= _buf2[0]; - buf2[1] &= _buf2[1]; stat = buf || buf2[0] || buf2[1] || sdca_cascade; /* -- 2.30.2

3 2

[PATCH v3 0/7] soundwire: qcom: add support for SM8550 (Soundwire v2.0.0)
by Krzysztof Kozlowski 08 May '23

08 May '23

Hi, Changes since v2: 1. Use uint16 for qcom,ports-sinterval. DTS will be fixed in separate patchset. 2. Add tags. Changes since v1: 1. Patch 1: Increase maxItems to 16 for port-related properties. 2. Re-order patch 1 and 2. 3. Patch 3: Drop unneeded semicolon. 4. Patch 5: Fix lang typo in subject. Best regards, Krzysztof Krzysztof Kozlowski (7): dt-bindings: soundwire: qcom: add Qualcomm Soundwire v2.0.0 dt-bindings: soundwire: qcom: add 16-bit sample interval soundwire: qcom: allow 16-bit sample interval for ports soundwire: qcom: use consistently 'ctrl' as state variable name soundwire: qcom: prepare for handling different register layouts soundwire: qcom: add support for v2.0.0 controller soundwire: qcom: use tabs for indentation in defines .../bindings/soundwire/qcom,soundwire.yaml | 39 +- drivers/soundwire/qcom.c | 387 ++++++++++++------ 2 files changed, 287 insertions(+), 139 deletions(-) -- 2.34.1

3 10

[PATCH v2 1/5] ASoC: tas2781: Add Header file for tas2781 driver
by Shenghao Ding 08 May '23

08 May '23

Create Header file for tas2781 driver. Signed-off-by: Shenghao Ding <13916275206(a)139.com> --- Changes in v2: - fixed issue | Reported-by: kernel test robot <lkp(a)intel.com> | Link: https://lore.kernel.org/oe-kbuild-all/202305022033.LiI7Ojm4-lkp@intel.com/ Changes to be committed: new file: include/sound/tas2781-dsp.h new file: include/sound/tas2781-tlv.h new file: include/sound/tas2781.h --- include/sound/tas2781-dsp.h | 189 ++++++++++++++++++++++++++++++++++++ include/sound/tas2781-tlv.h | 22 +++++ include/sound/tas2781.h | 176 +++++++++++++++++++++++++++++++++ 3 files changed, 387 insertions(+) create mode 100644 include/sound/tas2781-dsp.h create mode 100644 include/sound/tas2781-tlv.h create mode 100644 include/sound/tas2781.h diff --git a/include/sound/tas2781-dsp.h b/include/sound/tas2781-dsp.h new file mode 100644 index 000000000000..091c3ffade17 --- /dev/null +++ b/include/sound/tas2781-dsp.h @@ -0,0 +1,189 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +// +// ALSA SoC Texas Instruments TAS2781 Audio Smart Amplifier +// +// Copyright (C) 2022 - 2023 Texas Instruments Incorporated +// https://www.ti.com +// +// The TAS2781 driver implements a flexible and configurable +// algo coefficient setting for one, two, or even multiple +// TAS2781 chips. +// +// Author: Shenghao Ding <shenghao-ding(a)ti.com> +// Author: Kevin Lu <kevin-lu(a)ti.com> +// + +#ifndef __TASDEVICE_DSP_H__ +#define __TASDEVICE_DSP_H__ + +#define MAIN_ALL_DEVICES 0x0d +#define MAIN_DEVICE_A 0x01 +#define MAIN_DEVICE_B 0x08 +#define MAIN_DEVICE_C 0x10 +#define MAIN_DEVICE_D 0x14 +#define COEFF_DEVICE_A 0x03 +#define COEFF_DEVICE_B 0x0a +#define COEFF_DEVICE_C 0x11 +#define COEFF_DEVICE_D 0x15 +#define PRE_DEVICE_A 0x04 +#define PRE_DEVICE_B 0x0b +#define PRE_DEVICE_C 0x12 +#define PRE_DEVICE_D 0x16 + +#define PPC3_VERSION 0x4100 +#define RCA_CONFIGID_BYPASS_ALL 0 +#define TASDEVICE_DEVICE_SUM 8 +#define TASDEVICE_CONFIG_SUM 64 + +enum channel { + top_left_Chn, + top_right_chn, + bottom_left_Chn, + bottom_right_chn, + max_chn, +}; + +enum tasdevice_dsp_dev_idx { + TASDEVICE_DSP_TAS_2555 = 0, + TASDEVICE_DSP_TAS_2555_STEREO, + TASDEVICE_DSP_TAS_2557_MONO, + TASDEVICE_DSP_TAS_2557_DUAL_MONO, + TASDEVICE_DSP_TAS_2559, + TASDEVICE_DSP_TAS_2563, + TASDEVICE_DSP_TAS_2563_DUAL_MONO = 7, + TASDEVICE_DSP_TAS_2563_QUAD, + TASDEVICE_DSP_TAS_2563_21, + TASDEVICE_DSP_TAS_2781, + TASDEVICE_DSP_TAS_2781_DUAL_MONO, + TASDEVICE_DSP_TAS_2781_21, + TASDEVICE_DSP_TAS_2781_QUAD, + TASDEVICE_DSP_TAS_MAX_DEVICE +}; + +struct tasdevice_fw_fixed_hdr { + unsigned int fwsize; + unsigned int ppcver; + unsigned int drv_ver; +}; + +struct tasdevice_dspfw_hdr { + struct tasdevice_fw_fixed_hdr fixed_hdr; + unsigned short device_family; + unsigned short device; + unsigned char ndev; +}; + +struct tasdev_blk { + int nr_retry; + unsigned int type; + unsigned char is_pchksum_present; + unsigned char pchksum; + unsigned char is_ychksum_present; + unsigned char ychksum; + unsigned int nr_cmds; + unsigned int blk_size; + unsigned int nr_subblocks; + unsigned char *data; +}; + +struct tasdevice_data { + char name[64]; + unsigned int nr_blk; + struct tasdev_blk *dev_blks; +}; + +struct tasdevice_prog { + unsigned int prog_size; + struct tasdevice_data dev_data; +}; + +struct tasdevice_config { + unsigned int cfg_size; + char name[64]; + struct tasdevice_data dev_data; +}; + +struct tasdevice_calibration { + struct tasdevice_data dev_data; +}; + +struct tasdevice_fw { + struct tasdevice_dspfw_hdr fw_hdr; + unsigned short nr_programs; + struct tasdevice_prog *programs; + unsigned short nr_configurations; + struct tasdevice_config *configs; + unsigned short nr_calibrations; + struct tasdevice_calibration *calibrations; + struct device *dev; +}; + +enum tasdevice_dsp_fw_state { + TASDEVICE_DSP_FW_NONE = 0, + TASDEVICE_DSP_FW_PENDING, + TASDEVICE_DSP_FW_FAIL, + TASDEVICE_DSP_FW_ALL_OK, +}; + +enum tasdevice_bin_blk_type { + TASDEVICE_BIN_BLK_COEFF = 1, + TASDEVICE_BIN_BLK_POST_POWER_UP, + TASDEVICE_BIN_BLK_PRE_SHUTDOWN, + TASDEVICE_BIN_BLK_PRE_POWER_UP, + TASDEVICE_BIN_BLK_POST_SHUTDOWN +}; + +struct tasdevice_rca_hdr { + unsigned int img_sz; + unsigned int checksum; + unsigned int binary_version_num; + unsigned int drv_fw_version; + unsigned char plat_type; + unsigned char dev_family; + unsigned char reserve; + unsigned char ndev; + unsigned char devs[TASDEVICE_DEVICE_SUM]; + unsigned int nconfig; + unsigned int config_size[TASDEVICE_CONFIG_SUM]; +}; + +struct tasdev_blk_data { + unsigned char dev_idx; + unsigned char block_type; + unsigned short yram_checksum; + unsigned int block_size; + unsigned int n_subblks; + unsigned char *regdata; +}; + +struct tasdevice_config_info { + unsigned int nblocks; + unsigned int real_nblocks; + unsigned char active_dev; + struct tasdev_blk_data **blk_data; +}; + +struct tasdevice_rca { + struct tasdevice_rca_hdr fw_hdr; + int ncfgs; + struct tasdevice_config_info **cfg_info; + int profile_cfg_id; +}; + +void tasdevice_select_cfg_blk(void *context, int conf_no, + unsigned char block_type); +void tasdevice_config_info_remove(void *context); +void tasdevice_dsp_remove(void *context); +int tasdevice_dsp_parser(void *context); +int tasdevice_rca_parser(void *context, const struct firmware *fmw); +void tasdevice_dsp_remove(void *context); +void tasdevice_calbin_remove(void *context); +int tasdevice_select_tuningprm_cfg(void *context, int prm, + int cfg_no, int rca_conf_no); +int tasdevice_prmg_load(void *context, int prm_no); +int tasdevice_prmg_calibdata_load(void *context, int prm_no); +void tasdevice_tuning_switch(void *context, int state); +int tas2781_load_calibration(void *context, char *file_name, + enum channel i); + +#endif diff --git a/include/sound/tas2781-tlv.h b/include/sound/tas2781-tlv.h new file mode 100644 index 000000000000..f4310dce655a --- /dev/null +++ b/include/sound/tas2781-tlv.h @@ -0,0 +1,22 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +// +// ALSA SoC Texas Instruments TAS2781 Audio Smart Amplifier +// +// Copyright (C) 2022 - 2023 Texas Instruments Incorporated +// https://www.ti.com +// +// The TAS2781 driver implements a flexible and configurable +// algo coefficient setting for one, two, or even multiple +// TAS2781 chips. +// +// Author: Shenghao Ding <shenghao-ding(a)ti.com> +// Author: Kevin Lu <kevin-lu(a)ti.com> +// + +#ifndef __TAS2781_TLV_H__ +#define __TAS2781_TLV_H__ + +static const DECLARE_TLV_DB_SCALE(dvc_tlv, -10000, 100, 0); +static const DECLARE_TLV_DB_SCALE(amp_vol_tlv, 1100, 50, 0); + +#endif /* __TAS2781_LIB_H__ */ diff --git a/include/sound/tas2781.h b/include/sound/tas2781.h new file mode 100644 index 000000000000..c98955bda07e --- /dev/null +++ b/include/sound/tas2781.h @@ -0,0 +1,176 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +// +// ALSA SoC Texas Instruments TAS2781 Audio Smart Amplifier +// +// Copyright (C) 2022 - 2023 Texas Instruments Incorporated +// https://www.ti.com +// +// The TAS2781 driver implements a flexible and configurable +// algo coefficient setting for one, two, or even multiple +// TAS2781 chips. +// +// Author: Shenghao Ding <shenghao-ding(a)ti.com> +// Author: Kevin Lu <kevin-lu(a)ti.com> +// + +#ifndef __TAS2781_H__ +#define __TAS2781_H__ + +#include <linux/kernel.h> +#include "tas2781-dsp.h" + +/* version number */ +#define TAS2781_DRV_VER 1 +#define SMARTAMP_MODULE_NAME "tas2781" +#define TAS2781_GLOBAL_ADDR 0x40 +#define TASDEVICE_RATES (SNDRV_PCM_RATE_44100 |\ + SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_96000 |\ + SNDRV_PCM_RATE_88200) +#define TASDEVICE_MAX_CHANNELS 8 + +#define TASDEVICE_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | \ + SNDRV_PCM_FMTBIT_S24_LE | \ + SNDRV_PCM_FMTBIT_S32_LE) + +/*PAGE Control Register (available in page0 of each book) */ +#define TASDEVICE_PAGE_SELECT 0x00 +#define TASDEVICE_BOOKCTL_PAGE 0x00 +#define TASDEVICE_BOOKCTL_REG 127 +#define TASDEVICE_BOOK_ID(reg) (reg / (256 * 128)) +#define TASDEVICE_PAGE_ID(reg) ((reg % (256 * 128)) / 128) +#define TASDEVICE_PAGE_REG(reg) ((reg % (256 * 128)) % 128) +#define TASDEVICE_PGRG(reg) (reg % (256 * 128)) +#define TASDEVICE_REG(book, page, reg) (((book * 256 * 128) + \ + (page * 128)) + reg) + +/*Software Reset */ +#define TAS2781_REG_SWRESET TASDEVICE_REG(0x0, 0X0, 0x02) +#define TAS2781_REG_SWRESET_RESET BIT(0) + +/* Enable Global addresses */ +#define TAS2781_MISC_CFG2 TASDEVICE_REG(0x0, 0X0, 0x07) +#define TAS2781_GLOBAL_ADDR_MASK BIT(1) +#define TAS2781_GLOBAL_ADDR_ENABLE BIT(1) + +/*I2C Checksum */ +#define TASDEVICE_I2CChecksum TASDEVICE_REG(0x0, 0x0, 0x7E) + +/* Volume control */ +#define TAS2781_DVC_LVL TASDEVICE_REG(0x0, 0x0, 0x1A) +#define TAS2781_AMP_LEVEL TASDEVICE_REG(0x0, 0x0, 0x03) +#define TAS2781_AMP_LEVEL_MASK GENMASK(5, 1) + +#define TASDEVICE_CMD_SING_W 0x1 +#define TASDEVICE_CMD_BURST 0x2 +#define TASDEVICE_CMD_DELAY 0x3 +#define TASDEVICE_CMD_FIELD_W 0x4 + +enum audio_device { + TAS2781 = 0, +}; + +struct tasdevice { + struct tasdevice_fw *cali_data_fmw; + unsigned int dev_addr; + unsigned int err_code; + unsigned char cur_book; + short cur_prog; + short cur_conf; + bool is_loading; + bool is_loaderr; +}; + +/* + * This item is used to store the generic i2c address of + * all the tas2781 devices for I2C broadcast during the multi-device + * writes, useless in mono case. + */ +struct global_addr { + int ref_cnt; + unsigned int dev_addr; + unsigned char cur_book; +}; + +struct tasdevice_irqinfo { + int irq_gpio; + int irq; +}; + +struct calidata { + unsigned char *data; + unsigned long total_sz; +}; + +struct tasdevice_priv { + struct tasdevice tasdevice[max_chn]; + struct tasdevice_irqinfo irq_info; + struct global_addr glb_addr; + struct tasdevice_rca rcabin; + struct tasdevice_fw *fmw; + struct regmap *regmap; + struct mutex codec_lock; + struct calidata cali_data; + struct gpio_desc *reset; + struct device *dev; + struct tm tm; + + unsigned char crc8_lkp_tbl[CRC8_TABLE_SIZE]; + unsigned char cal_binaryname[max_chn][64]; + unsigned char coef_binaryname[64]; + unsigned char rca_binaryname[64]; + unsigned char dev_name[32]; + unsigned char ndev; + unsigned int magic_num; + unsigned int chip_id; + unsigned int sysclk; + const char *acpi_subsystem_id; + int index; + int cur_prog; + int cur_conf; + int fw_state; + void *client; + void *codec; + bool isacpi; + bool playback_started; + void (*set_global_mode)(struct tasdevice_priv *tas_priv); + int (*fw_parse_variable_header)(struct tasdevice_priv *tas_priv, + const struct firmware *fmw, int offset); + int (*fw_parse_program_data)(struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, + const struct firmware *fmw, int offset); + int (*fw_parse_configuration_data)(struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, + const struct firmware *fmw, int offset); + int (*tasdevice_load_block)(struct tasdevice_priv *tas_priv, + struct tasdev_blk *block); +}; + +void tas2781_reset(struct tasdevice_priv *tas_dev); +int tascodec_init(struct tasdevice_priv *tas_priv, void *codec, + void (*cont)(const struct firmware *fw, void *context)); +struct tasdevice_priv *tasdevice_kzalloc(struct i2c_client *i2c); +int tasdevice_init(struct tasdevice_priv *tas_priv); +void tasdevice_remove(struct tasdevice_priv *tas_priv); +int tasdevice_dev_read(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned int *value); +int tasdevice_dev_write(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned int value); +int tasdevice_dev_bulk_write( + struct tasdevice_priv *tas_priv, enum channel chn, + unsigned int reg, unsigned char *p_data, unsigned int n_length); +int tasdevice_dev_bulk_read(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned char *p_data, + unsigned int n_length); +int tasdevice_dev_update_bits( + struct tasdevice_priv *tasdevice, enum channel chn, + unsigned int reg, unsigned int mask, unsigned int value); +int tasdevice_amp_putvol(struct tasdevice_priv *tas_priv, + struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc); +int tasdevice_amp_getvol(struct tasdevice_priv *tas_priv, + struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc); +int tasdevice_digital_putvol(struct tasdevice_priv *tas_priv, + struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc); +int tasdevice_digital_getvol(struct tasdevice_priv *tas_priv, + struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc); + +#endif /* __TAS2781_H__ */ -- 2.34.1

2 1

[PATCH] ALSA: hda/realtek: Add quirk for ASUS GU603ZM
by frshuov＠163.com 08 May '23

08 May '23

From: Larry Chi <frshuov(a)163.com> ASUS ROG Zephyrus M16 2022 GU603ZM (1043:1c62) added SND_PCI_QUIRK for speaker and headset-mic working properly Signed-off-by: Larry Chi <frshuov(a)163.com> --- sound/pci/hda/patch_realtek.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 172ffc2c332b..374a9755d19a 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -9522,6 +9522,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x1043, 0x1b13, "Asus U41SV", ALC269_FIXUP_INV_DMIC), SND_PCI_QUIRK(0x1043, 0x1bbd, "ASUS Z550MA", ALC255_FIXUP_ASUS_MIC_NO_PRESENCE), SND_PCI_QUIRK(0x1043, 0x1c23, "Asus X55U", ALC269_FIXUP_LIMIT_INT_MIC_BOOST), + SND_PCI_QUIRK(0x1043, 0x1c62, "ASUS GU603ZM", ALC289_FIXUP_ASUS_GA401), SND_PCI_QUIRK(0x1043, 0x1c92, "ASUS ROG Strix G15", ALC285_FIXUP_ASUS_G533Z_PINS), SND_PCI_QUIRK(0x1043, 0x1ccd, "ASUS X555UB", ALC256_FIXUP_ASUS_MIC), SND_PCI_QUIRK(0x1043, 0x1d42, "ASUS Zephyrus G14 2022", ALC289_FIXUP_ASUS_GA401), -- 2.40.1

2 1

[PATCH] ALSA: hda/realtek: Add a quirk for HP EliteDesk 805
by Ai Chao 08 May '23

08 May '23

Add a quirk for HP EliteDesk 805 to fixup ALC3867 headset MIC no sound. Signed-off-by: Ai Chao <aichao(a)kylinos.cn> --- sound/pci/hda/patch_realtek.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 068ce0db9562..cbb3c3f6d502 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -11662,6 +11662,7 @@ static const struct snd_pci_quirk alc662_fixup_tbl[] = { SND_PCI_QUIRK(0x103c, 0x1632, "HP RP5800", ALC662_FIXUP_HP_RP5800), SND_PCI_QUIRK(0x103c, 0x870c, "HP", ALC897_FIXUP_HP_HSMIC_VERB), SND_PCI_QUIRK(0x103c, 0x8719, "HP", ALC897_FIXUP_HP_HSMIC_VERB), + SND_PCI_QUIRK(0x103c, 0x872b, "HP", ALC897_FIXUP_HP_HSMIC_VERB), SND_PCI_QUIRK(0x103c, 0x873e, "HP", ALC671_FIXUP_HP_HEADSET_MIC2), SND_PCI_QUIRK(0x103c, 0x877e, "HP 288 Pro G6", ALC671_FIXUP_HP_HEADSET_MIC2), SND_PCI_QUIRK(0x103c, 0x885f, "HP 288 Pro G8", ALC671_FIXUP_HP_HEADSET_MIC2), -- 2.25.1

2 1

[PATCH v2 0/1] ALSA: hda/realtek: Add quirk for 2nd ASUS GU603
by Luke D. Jones 08 May '23

08 May '23

Add quirk for GU603 with alt codec ID. Changelog: - V2 - Move line to correct place in order Luke D. Jones (1): ALSA: hda/realtek: Add quirk for 2nd ASUS GU603 sound/pci/hda/patch_realtek.c | 1 + 1 file changed, 1 insertion(+) -- 2.40.0

2 2

[PATCH] ALSA: hda/realtek: Add quirk for Clevo L140AU
by Tim Crawford 08 May '23

08 May '23

From: Jeremy Soller <jeremy(a)system76.com> Fixes headset detection on Clevo L140AU. Signed-off-by: Jeremy Soller <jeremy(a)system76.com> Signed-off-by: Tim Crawford <tcrawford(a)system76.com> --- sound/pci/hda/patch_realtek.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 068ce0db9562..570f3478c4e7 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -9617,6 +9617,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x1558, 0x7716, "Clevo NS50PU", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE), SND_PCI_QUIRK(0x1558, 0x7717, "Clevo NS70PU", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE), SND_PCI_QUIRK(0x1558, 0x7718, "Clevo L140PU", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE), + SND_PCI_QUIRK(0x1558, 0x7724, "Clevo L140AU", ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE), SND_PCI_QUIRK(0x1558, 0x8228, "Clevo NR40BU", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE), SND_PCI_QUIRK(0x1558, 0x8520, "Clevo NH50D[CD]", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE), SND_PCI_QUIRK(0x1558, 0x8521, "Clevo NH77D[CD]", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE), -- 2.40.1

2 1

[PATCH v2 5/5] ALSA: hda/tas2781: Add tas2781 HDA driver
by Shenghao Ding 08 May '23

08 May '23

Create tas2781 HDA driver. Signed-off-by: Shenghao Ding <13916275206(a)139.com> --- Changes in v2: - fixed issue | Reported-by: kernel test robot <lkp(a)intel.com> | Link: https://lore.kernel.org/oe-kbuild-all/202305022033.LiI7Ojm4-lkp@intel.com/ Changes to be committed: modified: sound/pci/hda/Kconfig modified: sound/pci/hda/Makefile modified: sound/pci/hda/patch_realtek.c new file: sound/pci/hda/tas2781_hda_i2c.c --- sound/pci/hda/Kconfig | 15 + sound/pci/hda/Makefile | 2 + sound/pci/hda/patch_realtek.c | 106 ++++- sound/pci/hda/tas2781_hda_i2c.c | 806 ++++++++++++++++++++++++++++++++ 4 files changed, 926 insertions(+), 3 deletions(-) create mode 100644 sound/pci/hda/tas2781_hda_i2c.c diff --git a/sound/pci/hda/Kconfig b/sound/pci/hda/Kconfig index 886255a03e8b..e66257277492 100644 --- a/sound/pci/hda/Kconfig +++ b/sound/pci/hda/Kconfig @@ -130,6 +130,21 @@ config SND_HDA_SCODEC_CS35L41_SPI comment "Set to Y if you want auto-loading the side codec driver" depends on SND_HDA=y && SND_HDA_SCODEC_CS35L41_SPI=m +config SND_HDA_SCODEC_TAS2781_I2C + tristate "Build TAS2781 HD-audio side codec support for I2C Bus" + depends on I2C + depends on ACPI + depends on SND_SOC + select SND_SOC_TAS2781_COMLIB + select SND_SOC_TAS2781_FMWLIB + select CRC32_SARWATE + help + Say Y or M here to include TAS2781 I2C HD-audio side codec support + in snd-hda-intel driver, such as ALC287. + +comment "Set to Y if you want auto-loading the side codec driver" + depends on SND_HDA=y && SND_HDA_SCODEC_TAS2781_I2C=m + config SND_HDA_CODEC_REALTEK tristate "Build Realtek HD-audio codec support" select SND_HDA_GENERIC diff --git a/sound/pci/hda/Makefile b/sound/pci/hda/Makefile index 00d306104484..1c76609690d6 100644 --- a/sound/pci/hda/Makefile +++ b/sound/pci/hda/Makefile @@ -32,6 +32,7 @@ snd-hda-scodec-cs35l41-objs := cs35l41_hda.o snd-hda-scodec-cs35l41-i2c-objs := cs35l41_hda_i2c.o snd-hda-scodec-cs35l41-spi-objs := cs35l41_hda_spi.o snd-hda-cs-dsp-ctls-objs := hda_cs_dsp_ctl.o +snd-hda-scodec-tas2781-i2c-objs := tas2781_hda_i2c.o # common driver obj-$(CONFIG_SND_HDA) := snd-hda-codec.o @@ -56,6 +57,7 @@ obj-$(CONFIG_SND_HDA_SCODEC_CS35L41) += snd-hda-scodec-cs35l41.o obj-$(CONFIG_SND_HDA_SCODEC_CS35L41_I2C) += snd-hda-scodec-cs35l41-i2c.o obj-$(CONFIG_SND_HDA_SCODEC_CS35L41_SPI) += snd-hda-scodec-cs35l41-spi.o obj-$(CONFIG_SND_HDA_CS_DSP_CONTROLS) += snd-hda-cs-dsp-ctls.o +obj-$(CONFIG_SND_HDA_SCODEC_TAS2781_I2C) += snd-hda-scodec-tas2781-i2c.o # this must be the last entry after codec drivers; # otherwise the codec patches won't be hooked before the PCI probe diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 172ffc2c332b..f5b912f90018 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -6705,7 +6705,7 @@ static void comp_generic_playback_hook(struct hda_pcm_stream *hinfo, struct hda_ } } -struct cs35l41_dev_name { +struct scodec_dev_name { const char *bus; const char *hid; int index; @@ -6714,7 +6714,7 @@ struct cs35l41_dev_name { /* match the device name in a slightly relaxed manner */ static int comp_match_cs35l41_dev_name(struct device *dev, void *data) { - struct cs35l41_dev_name *p = data; + struct scodec_dev_name *p = data; const char *d = dev_name(dev); int n = strlen(p->bus); char tmp[32]; @@ -6730,12 +6730,31 @@ static int comp_match_cs35l41_dev_name(struct device *dev, void *data) return !strcmp(d + n, tmp); } +static int comp_match_tas2781_dev_name(struct device *dev, void *data) +{ + struct scodec_dev_name *p = data; + const char *d = dev_name(dev); + int n = strlen(p->bus); + char tmp[32]; + + /* check the bus name */ + if (strncmp(d, p->bus, n)) + return 0; + /* skip the bus number */ + if (isdigit(d[n])) + n++; + /* the rest must be exact matching */ + snprintf(tmp, sizeof(tmp), "-%s:00", p->hid); + + return !strcmp(d + n, tmp); +} + static void cs35l41_generic_fixup(struct hda_codec *cdc, int action, const char *bus, const char *hid, int count) { struct device *dev = hda_codec_dev(cdc); struct alc_spec *spec = cdc->spec; - struct cs35l41_dev_name *rec; + struct scodec_dev_name *rec; int ret, i; switch (action) { @@ -6760,6 +6779,40 @@ static void cs35l41_generic_fixup(struct hda_codec *cdc, int action, const char } } +static void tas2781_generic_fixup(struct hda_codec *cdc, int action, + const char *bus, const char *hid, int count) +{ + struct device *dev = hda_codec_dev(cdc); + struct alc_spec *spec = cdc->spec; + struct scodec_dev_name *rec; + int ret, i; + + switch (action) { + case HDA_FIXUP_ACT_PRE_PROBE: + for (i = 0; i < count; i++) { + rec = devm_kmalloc(dev, sizeof(*rec), GFP_KERNEL); + if (!rec) + return; + rec->bus = bus; + rec->hid = hid; + rec->index = i; + spec->comps[i].codec = cdc; + component_match_add(dev, &spec->match, + comp_match_tas2781_dev_name, rec); + } + ret = component_master_add_with_match(dev, &comp_master_ops, + spec->match); + if (ret) + codec_err(cdc, + "Fail to register component aggregator %d\n", + ret); + else + spec->gen.pcm_playback_hook = + comp_generic_playback_hook; + break; + } +} + static void cs35l41_fixup_i2c_two(struct hda_codec *cdc, const struct hda_fixup *fix, int action) { cs35l41_generic_fixup(cdc, action, "i2c", "CSC3551", 2); @@ -6787,6 +6840,12 @@ static void alc287_fixup_legion_16ithg6_speakers(struct hda_codec *cdc, const st cs35l41_generic_fixup(cdc, action, "i2c", "CLSA0101", 2); } +static void tas2781_fixup_i2c(struct hda_codec *cdc, + const struct hda_fixup *fix, int action) +{ + tas2781_generic_fixup(cdc, action, "i2c", "TIAS2781", 1); +} + /* for alc295_fixup_hp_top_speakers */ #include "hp_x360_helper.c" @@ -7201,6 +7260,8 @@ enum { ALC287_FIXUP_YOGA9_14IAP7_BASS_SPK_PIN, ALC295_FIXUP_DELL_INSPIRON_TOP_SPEAKERS, ALC236_FIXUP_DELL_DUAL_CODECS, + ALC287_FIXUP_TAS2781_I2C_2, + ALC287_FIXUP_TAS2781_I2C_4 }; /* A special fixup for Lenovo C940 and Yoga Duet 7; @@ -9189,6 +9250,18 @@ static const struct hda_fixup alc269_fixups[] = { .chained = true, .chain_id = ALC255_FIXUP_DELL1_MIC_NO_PRESENCE, }, + [ALC287_FIXUP_TAS2781_I2C_2] = { + .type = HDA_FIXUP_FUNC, + .v.func = tas2781_fixup_i2c, + .chained = true, + .chain_id = ALC269_FIXUP_THINKPAD_ACPI, + }, + [ALC287_FIXUP_TAS2781_I2C_4] = { + .type = HDA_FIXUP_FUNC, + .v.func = tas2781_fixup_i2c, + .chained = true, + .chain_id = ALC269_FIXUP_THINKPAD_ACPI, + }, }; static const struct snd_pci_quirk alc269_fixup_tbl[] = { @@ -9725,6 +9798,33 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x17aa, 0x3853, "Lenovo Yoga 7 15ITL5", ALC287_FIXUP_YOGA7_14ITL_SPEAKERS), SND_PCI_QUIRK(0x17aa, 0x3855, "Legion 7 16ITHG6", ALC287_FIXUP_LEGION_16ITHG6), SND_PCI_QUIRK(0x17aa, 0x3869, "Lenovo Yoga7 14IAL7", ALC287_FIXUP_YOGA9_14IAP7_BASS_SPK_PIN), + SND_PCI_QUIRK(0x17aa, 0x387d, "Yoga S780-16 pro Quad AAC", + ALC287_FIXUP_TAS2781_I2C_4), + SND_PCI_QUIRK(0x17aa, 0x387e, "Yoga S780-16 pro Quad YC", + ALC287_FIXUP_TAS2781_I2C_4), + SND_PCI_QUIRK(0x17aa, 0x3881, "YB9 dual powe mode2 YC", + ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x3884, "Y780 YG DUAL", + ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x3886, "Y780 VECO DUAL", + ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x38a7, "Y780P AMD YG dual", + ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x38a8, "Y780P AMD VECO dual", + ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x38ba, "Yoga S780-14.5 Air AMD quad YC", + ALC287_FIXUP_TAS2781_I2C_4), + SND_PCI_QUIRK(0x17aa, 0x38bb, "Yoga S780-14.5 Air AMD quad AAC", + ALC287_FIXUP_TAS2781_I2C_4), + SND_PCI_QUIRK(0x17aa, 0x38be, "Yoga S980-14.5 proX YC Dual", + ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x38bf, "Yoga S980-14.5 proX LX Dual", + ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x38c3, "Y980 DUAL", ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x38cb, "Y790 YG DUAL", + ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x38cd, "Y790 VECO DUAL", + ALC287_FIXUP_TAS2781_I2C_2), SND_PCI_QUIRK(0x17aa, 0x3902, "Lenovo E50-80", ALC269_FIXUP_DMIC_THINKPAD_ACPI), SND_PCI_QUIRK(0x17aa, 0x3977, "IdeaPad S210", ALC283_FIXUP_INT_MIC), SND_PCI_QUIRK(0x17aa, 0x3978, "Lenovo B50-70", ALC269_FIXUP_DMIC_THINKPAD_ACPI), diff --git a/sound/pci/hda/tas2781_hda_i2c.c b/sound/pci/hda/tas2781_hda_i2c.c new file mode 100644 index 000000000000..a742805b749b --- /dev/null +++ b/sound/pci/hda/tas2781_hda_i2c.c @@ -0,0 +1,806 @@ +// SPDX-License-Identifier: GPL-2.0 +// +// TAS2781 HDA I2C driver +// +// Copyright 2023 Texas Instruments, Inc. +// +// Author: Shenghao Ding <shenghao-ding(a)ti.com> + +#include <linux/acpi.h> +#include <linux/crc8.h> +#include <linux/crc32.h> +#include <linux/efi.h> +#include <linux/firmware.h> +#include <linux/i2c.h> +#include <linux/mod_devicetable.h> +#include <linux/module.h> +#include <linux/pm_runtime.h> +#include <linux/regmap.h> +#include <sound/hda_codec.h> +#include <sound/soc.h> +#include <sound/tas2781.h> +#include <sound/tlv.h> +#include <sound/tas2781-tlv.h> + +#include "hda_local.h" +#include "hda_auto_parser.h" +#include "hda_component.h" +#include "hda_jack.h" +#include "hda_generic.h" + +#define TASDEVICE_SPEAKER_CALIBRATION_SIZE 20 + +#define ACARD_SINGLE_RANGE_EXT_TLV(xname, xreg, xshift, xmin, xmax, xinvert, \ + xhandler_get, xhandler_put, tlv_array) \ +{ .iface = SNDRV_CTL_ELEM_IFACE_CARD, .name = (xname),\ + .access = SNDRV_CTL_ELEM_ACCESS_TLV_READ |\ + SNDRV_CTL_ELEM_ACCESS_READWRITE,\ + .tlv.p = (tlv_array), \ + .info = snd_soc_info_volsw_range, \ + .get = xhandler_get, .put = xhandler_put, \ + .private_value = (unsigned long)&(struct soc_mixer_control) \ + {.reg = xreg, .rreg = xreg, .shift = xshift, \ + .rshift = xshift, .min = xmin, .max = xmax, \ + .invert = xinvert} } + +enum calib_data { + R0_VAL = 0, + INV_R0, + R0LOW, + POWER, + TLIM, + CALIB_MAX +}; + +static int tas2781_acpi_get_i2c_resource(struct acpi_resource + *ares, void *data) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)data; + struct acpi_resource_i2c_serialbus *sb; + + if (i2c_acpi_get_i2c_resource(ares, &sb)) { + if (sb->slave_address != TAS2781_GLOBAL_ADDR) { + tas_priv->tasdevice[tas_priv->ndev].dev_addr = + (unsigned int) sb->slave_address; + tas_priv->ndev++; + } else + tas_priv->glb_addr.dev_addr = TAS2781_GLOBAL_ADDR; + + } + + return 1; +} + +static int tas2781_hda_read_acpi(struct tasdevice_priv *tas_priv, + const char *hid) +{ + struct acpi_device *adev; + struct device *physdev; + LIST_HEAD(resources); + const char *sub; + int ret; + + adev = acpi_dev_get_first_match_dev(hid, NULL, -1); + if (!adev) { + dev_err(tas_priv->dev, + "Failed to find an ACPI device for %s\n", hid); + return -ENODEV; + } + strcpy(tas_priv->dev_name, hid); + physdev = get_device(acpi_get_first_physical_node(adev)); + acpi_dev_put(adev); + + sub = acpi_get_subsystem_id(ACPI_HANDLE(physdev)); + if (IS_ERR(sub)) + sub = NULL; + dev_info(tas_priv->dev, "subid = %s\n", sub); + + tas_priv->acpi_subsystem_id = sub; + + ret = acpi_dev_get_resources(adev, &resources, + tas2781_acpi_get_i2c_resource, tas_priv); + if (ret < 0) + goto err; + acpi_dev_free_resource_list(&resources); + + put_device(physdev); + dev_info(tas_priv->dev, "global addr: 0x%02x devcnt = %d\n", + tas_priv->glb_addr.dev_addr, tas_priv->ndev); + + return 0; + +err: + dev_err(tas_priv->dev, "Failed acpi ret: %d\n", ret); + put_device(physdev); + + return ret; +} + +static void tas2781_hda_playback_hook(struct device *dev, int action) +{ + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev); + int ret = 0; + + dev_info(tas_priv->dev, "%s: action = %d\n", __func__, action); + switch (action) { + case HDA_GEN_PCM_ACT_OPEN: + pm_runtime_get_sync(dev); + mutex_lock(&tas_priv->codec_lock); + tas_priv->cur_conf = 0; + tas_priv->rcabin.profile_cfg_id = 1; + tasdevice_tuning_switch(tas_priv, 0); + mutex_unlock(&tas_priv->codec_lock); + break; + case HDA_GEN_PCM_ACT_CLOSE: + mutex_lock(&tas_priv->codec_lock); + tasdevice_tuning_switch(tas_priv, 1); + mutex_unlock(&tas_priv->codec_lock); + + pm_runtime_mark_last_busy(dev); + pm_runtime_put_autosuspend(dev); + break; + default: + dev_warn(tas_priv->dev, "Playback action not supported: %d\n", + action); + break; + } + + if (ret) + dev_err(tas_priv->dev, "Regmap access fail: %d\n", ret); +} + +static int tasdevice_info_profile(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = 1; + uinfo->value.integer.min = 1; + uinfo->value.integer.max = max(0, tas_priv->rcabin.ncfgs); + + return 0; +} + +static int tasdevice_get_profile_id(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + + ucontrol->value.integer.value[0] = tas_priv->rcabin.profile_cfg_id; + + return 0; +} + +static int tasdevice_set_profile_id(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + + tas_priv->rcabin.profile_cfg_id = ucontrol->value.integer.value[0]; + + return 1; +} + +static int tasdevice_create_control(struct tasdevice_priv *tas_priv) +{ + char prof_ctrl_name[SNDRV_CTL_ELEM_ID_NAME_MAXLEN]; + struct hda_codec *codec = tas_priv->codec; + struct snd_kcontrol_new prof_ctrl = { + .name = prof_ctrl_name, + .iface = SNDRV_CTL_ELEM_IFACE_CARD, + .info = tasdevice_info_profile, + .get = tasdevice_get_profile_id, + .put = tasdevice_set_profile_id, + }; + int ret; + + /* Create a mixer item for selecting the active profile */ + scnprintf(prof_ctrl_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, + "tasdev-profile-id"); + ret = snd_ctl_add(codec->card, snd_ctl_new1(&prof_ctrl, tas_priv)); + if (ret) { + dev_err(tas_priv->dev, "Failed to add KControl %s = %d\n", + prof_ctrl.name, ret); + goto out; + } + + dev_dbg(tas_priv->dev, "Added Control %s\n", prof_ctrl.name); + +out: + return ret; +} + +static int tasdevice_info_programs(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + struct tasdevice_fw *tas_fw = tas_priv->fmw; + + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = 1; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = (int)tas_fw->nr_programs; + + return 0; +} + +static int tasdevice_info_configurations( + struct snd_kcontrol *kcontrol, struct snd_ctl_elem_info *uinfo) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + struct tasdevice_fw *tas_fw = tas_priv->fmw; + + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = 1; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = (int)tas_fw->nr_configurations - 1; + + return 0; +} + +static int tasdevice_program_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + + ucontrol->value.integer.value[0] = tas_priv->cur_prog; + + return 0; +} + +static int tasdevice_program_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + unsigned int nr_program = ucontrol->value.integer.value[0]; + + tas_priv->cur_prog = nr_program; + + return 1; +} + +static int tasdevice_config_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + + ucontrol->value.integer.value[0] = tas_priv->cur_conf; + + return 0; +} + +static int tasdevice_config_put( + struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + unsigned int nr_configuration = ucontrol->value.integer.value[0]; + + tas_priv->cur_conf = nr_configuration; + + return 1; +} + +/** + * tas2781_digital_getvol - get the volum control + * @kcontrol: control pointer + * @ucontrol: User data + * Customer Kcontrol for tas2781 is primarily for regmap booking, paging + * depends on internal regmap mechanism. + * tas2781 contains book and page two-level register map, especially + * book switching will set the register BXXP00R7F, after switching to the + * correct book, then leverage the mechanism for paging to access the + * register. + */ +static int tas2781_digital_getvol(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + + return tasdevice_digital_getvol(tas_priv, ucontrol, mc); +} + +static int tas2781_amp_getvol(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + + return tasdevice_amp_getvol(tas_priv, ucontrol, mc); +} + +static int tas2781_digital_putvol(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + + return tasdevice_digital_putvol(tas_priv, ucontrol, mc); +} + +static int tas2781_amp_putvol(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + + return tasdevice_amp_putvol(tas_priv, ucontrol, mc); +} + +static const struct snd_kcontrol_new tas2781_snd_controls[] = { + ACARD_SINGLE_RANGE_EXT_TLV("Amp Gain Volume", TAS2781_AMP_LEVEL, + 1, 0, 20, 0, tas2781_amp_getvol, + tas2781_amp_putvol, amp_vol_tlv), + ACARD_SINGLE_RANGE_EXT_TLV("Digital Volume", TAS2781_DVC_LVL, + 0, 0, 200, 1, tas2781_digital_getvol, + tas2781_digital_putvol, dvc_tlv), +}; + +static int tasdevice_dsp_create_ctrls(struct tasdevice_priv + *tas_priv) +{ + char prog_name[SNDRV_CTL_ELEM_ID_NAME_MAXLEN]; + char conf_name[SNDRV_CTL_ELEM_ID_NAME_MAXLEN]; + struct hda_codec *codec = tas_priv->codec; + struct snd_kcontrol_new prog_ctl = { + .name = prog_name, + .iface = SNDRV_CTL_ELEM_IFACE_CARD, + .info = tasdevice_info_programs, + .get = tasdevice_program_get, + .put = tasdevice_program_put, + }; + struct snd_kcontrol_new conf_ctl = { + .name = conf_name, + .iface = SNDRV_CTL_ELEM_IFACE_CARD, + .info = tasdevice_info_configurations, + .get = tasdevice_config_get, + .put = tasdevice_config_put, + }; + int ret; + + scnprintf(prog_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, "tasdev-prog-id"); + scnprintf(conf_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, "tasdev-conf-id"); + + ret = snd_ctl_add(codec->card, snd_ctl_new1(&prog_ctl, tas_priv)); + if (ret) { + dev_err(tas_priv->dev, "Failed to add KControl %s = %d\n", + prog_ctl.name, ret); + goto out; + } + + dev_dbg(tas_priv->dev, "Added Control %s\n", prog_ctl.name); + + ret = snd_ctl_add(codec->card, snd_ctl_new1(&conf_ctl, tas_priv)); + if (ret) { + dev_err(tas_priv->dev, "Failed to add KControl %s = %d\n", + conf_ctl.name, ret); + goto out; + } + + dev_dbg(tas_priv->dev, "Added Control %s\n", conf_ctl.name); +out: + return ret; +} + +static void tas2781_apply_calib(struct tasdevice_priv *tas_priv) +{ + unsigned char page_array[CALIB_MAX] = {0x17, 0x18, 0x18, 0x0d, 0x18}; + unsigned char rgno_array[CALIB_MAX] = {0x74, 0x0c, 0x14, 0x3c, 0x7c}; + unsigned char *data; + int i, j, rc; + + for (i = 0; i < tas_priv->ndev; i++) { + data = tas_priv->cali_data.data + + i * TASDEVICE_SPEAKER_CALIBRATION_SIZE; + for (j = 0; j < CALIB_MAX; j++) { + rc = tasdevice_dev_bulk_write(tas_priv, i, + TASDEVICE_REG(0, page_array[j], rgno_array[j]), + &(data[4 * j]), 4); + if (rc < 0) + dev_err(tas_priv->dev, + "chn %d calib %d bulk_wr err = %d\n", + i, j, rc); + } + } +} + +static int tas2781_save_calibration(struct tasdevice_priv *tas_priv) +{ + efi_guid_t efi_guid = EFI_GUID(0x02f9af02, 0x7734, 0x4233, 0xb4, 0x3d, + 0x93, 0xfe, 0x5a, 0xa3, 0x5d, 0xb3); + static efi_char16_t efi_name[] = L"CALI_DATA"; + struct hda_codec *codec = tas_priv->codec; + unsigned int subid = codec->core.subsystem_id & 0xFFFF; + struct tm *tm = &tas_priv->tm; + unsigned int attr, crc; + unsigned int *tmp_val; + efi_status_t status; + int ret = 0; + + //Lenovo devices + if ((subid == 0x387d) || (subid == 0x387e) || (subid == 0x3881) + || (subid == 0x3884) || (subid == 0x3886) || (subid == 0x38a7) + || (subid == 0x38a8) || (subid == 0x38ba) || (subid == 0x38bb) + || (subid == 0x38be) || (subid == 0x38bf) || (subid == 0x38c3) + || (subid == 0x38cb) || (subid == 0x38cd)) + efi_guid = EFI_GUID(0x1f52d2a1, 0xbb3a, 0x457d, 0xbc, 0x09, + 0x43, 0xa3, 0xf4, 0x31, 0x0a, 0x92); + tas_priv->cali_data.total_sz = 0; + /* Get real size of UEFI variable */ + status = efi.get_variable(efi_name, &efi_guid, &attr, + &tas_priv->cali_data.total_sz, tas_priv->cali_data.data); + if (status == EFI_BUFFER_TOO_SMALL) { + ret = -ENODEV; + /* Allocate data buffer of data_size bytes */ + tas_priv->cali_data.data = devm_kzalloc(tas_priv->dev, + tas_priv->cali_data.total_sz, GFP_KERNEL); + if (!tas_priv->cali_data.data) + return -ENOMEM; + /* Get variable contents into buffer */ + status = efi.get_variable(efi_name, &efi_guid, &attr, + &tas_priv->cali_data.total_sz, + tas_priv->cali_data.data); + if (status != EFI_SUCCESS) { + ret = -EINVAL; + goto out; + } + } + + tmp_val = (unsigned int *)tas_priv->cali_data.data; + + crc = crc32(~0, tas_priv->cali_data.data, 84) ^ ~0; + dev_info(tas_priv->dev, "cali crc 0x%08x PK tmp_val 0x%08x\n", + crc, tmp_val[21]); + + if (crc == tmp_val[21]) { + time64_to_tm(tmp_val[20], 0, tm); + dev_info(tas_priv->dev, "%4ld-%2d-%2d, %2d:%2d:%2d\n", + tm->tm_year, tm->tm_mon, tm->tm_mday, + tm->tm_hour, tm->tm_min, tm->tm_sec); + tas2781_apply_calib(tas_priv); + } +out: + return ret; +} + +static void tasdevice_fw_ready(const struct firmware *fmw, + void *context) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)context; + struct hda_codec *codec = tas_priv->codec; + int i, ret = 0; + + pm_runtime_get_sync(tas_priv->dev); + mutex_lock(&tas_priv->codec_lock); + + ret = tasdevice_rca_parser(tas_priv, fmw); + if (ret) + goto out; + tasdevice_create_control(tas_priv); + + for (i = 0; i < ARRAY_SIZE(tas2781_snd_controls); i++) { + ret = snd_ctl_add(codec->card, + snd_ctl_new1(&tas2781_snd_controls[i], tas_priv)); + if (ret) { + dev_err(tas_priv->dev, + "Failed to add KControl %s = %d\n", + tas2781_snd_controls[i].name, ret); + goto out; + } + } + + tasdevice_dsp_remove(tas_priv); + + tas_priv->fw_state = TASDEVICE_DSP_FW_PENDING; + scnprintf(tas_priv->coef_binaryname, 64, "TAS2XXX%04X.bin", + codec->core.subsystem_id & 0xffff); + ret = tasdevice_dsp_parser(tas_priv); + if (ret) { + dev_err(tas_priv->dev, "dspfw load %s error\n", + tas_priv->coef_binaryname); + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + goto out; + } + tasdevice_dsp_create_ctrls(tas_priv); + + tas_priv->fw_state = TASDEVICE_DSP_FW_ALL_OK; + tasdevice_prmg_load(tas_priv, 0); + tas_priv->cur_prog = 0; + + /* If calibrated data occurs error, dsp will still works with default + * calibrated data inside algo. + */ + tas2781_save_calibration(tas_priv); + +out: + if (tas_priv->fw_state == TASDEVICE_DSP_FW_FAIL) { + /*If DSP FW fail, kcontrol won't be created */ + tasdevice_config_info_remove(tas_priv); + tasdevice_dsp_remove(tas_priv); + } + mutex_unlock(&tas_priv->codec_lock); + if (fmw) + release_firmware(fmw); + pm_runtime_mark_last_busy(tas_priv->dev); + pm_runtime_put_autosuspend(tas_priv->dev); +} + +static int tas2781_hda_bind(struct device *dev, struct device *master, + void *master_data) +{ + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev); + struct hda_component *comps = master_data; + int ret = 0; + + if (!comps || tas_priv->index < 0 || + tas_priv->index >= HDA_MAX_COMPONENTS) + return -EINVAL; + + comps = &comps[tas_priv->index]; + if (comps->dev) + return -EBUSY; + + pm_runtime_get_sync(dev); + + comps->dev = dev; + + strscpy(comps->name, dev_name(dev), sizeof(comps->name)); + + ret = tascodec_init(tas_priv, comps->codec, tasdevice_fw_ready); + + comps->playback_hook = tas2781_hda_playback_hook; + + pm_runtime_mark_last_busy(dev); + pm_runtime_put_autosuspend(dev); + + return ret; +} + +static void tas2781_hda_unbind(struct device *dev, + struct device *master, void *master_data) +{ + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev); + struct hda_component *comps = master_data; + + if (comps[tas_priv->index].dev == dev) + memset(&comps[tas_priv->index], 0, sizeof(*comps)); + + tasdevice_config_info_remove(tas_priv); + tasdevice_dsp_remove(tas_priv); + + tas_priv->fw_state = TASDEVICE_DSP_FW_PENDING; +} + +static const struct component_ops tas2781_hda_comp_ops = { + .bind = tas2781_hda_bind, + .unbind = tas2781_hda_unbind, +}; + +static void tas2781_hda_remove(struct device *dev) +{ + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev); + + pm_runtime_get_sync(tas_priv->dev); + pm_runtime_disable(tas_priv->dev); + + + component_del(tas_priv->dev, &tas2781_hda_comp_ops); + + pm_runtime_put_noidle(tas_priv->dev); + + tasdevice_remove(tas_priv); +} + +static int tas2781_hda_i2c_probe(struct i2c_client *clt) +{ + struct tasdevice_priv *tas_priv; + const char *device_name; + int ret; + + if (strstr(dev_name(&clt->dev), "TIAS2781")) + device_name = "TIAS2781"; + else + return -ENODEV; + + tas_priv = tasdevice_kzalloc(clt); + if (!tas_priv) + return -ENOMEM; + + tas_priv->irq_info.irq = clt->irq; + ret = tas2781_hda_read_acpi(tas_priv, device_name); + if (ret) + return dev_err_probe(tas_priv->dev, ret, + "Platform not supported\n"); + + ret = tasdevice_init(tas_priv); + if (ret) + goto err; + + pm_runtime_set_autosuspend_delay(tas_priv->dev, 3000); + pm_runtime_use_autosuspend(tas_priv->dev); + pm_runtime_mark_last_busy(tas_priv->dev); + pm_runtime_set_active(tas_priv->dev); + pm_runtime_get_noresume(tas_priv->dev); + pm_runtime_enable(tas_priv->dev); + + pm_runtime_put_autosuspend(tas_priv->dev); + + ret = component_add(tas_priv->dev, &tas2781_hda_comp_ops); + if (ret) { + dev_err(tas_priv->dev, "Register component failed: %d\n", ret); + pm_runtime_disable(tas_priv->dev); + } + +err: + if (ret) + tas2781_hda_remove(&clt->dev); + return ret; +} + +static void tas2781_hda_i2c_remove(struct i2c_client *clt) +{ + tas2781_hda_remove(&clt->dev); +} + +static int tas2781_runtime_suspend(struct device *dev) +{ + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev); + int i, ret = 0; + + dev_info(tas_priv->dev, "Runtime Suspend\n"); + + mutex_lock(&tas_priv->codec_lock); + + if (tas_priv->playback_started) { + tasdevice_tuning_switch(tas_priv, 1); + tas_priv->playback_started = false; + } + + tas_priv->cur_prog = -1; + tas_priv->cur_conf = -1; + + for (i = 0; i < tas_priv->ndev; i++) { + tas_priv->tasdevice[i].cur_book = -1; + tas_priv->tasdevice[i].cur_prog = -1; + tas_priv->tasdevice[i].cur_conf = -1; + } + + regcache_cache_only(tas_priv->regmap, true); + regcache_mark_dirty(tas_priv->regmap); + + mutex_unlock(&tas_priv->codec_lock); + + return ret; +} + +static int tas2781_runtime_resume(struct device *dev) +{ + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev); + unsigned long calib_data_sz = + tas_priv->ndev * TASDEVICE_SPEAKER_CALIBRATION_SIZE; + int ret = 0; + + dev_info(tas_priv->dev, "Runtime Resume\n"); + + mutex_lock(&tas_priv->codec_lock); + + regcache_cache_only(tas_priv->regmap, false); + ret = regcache_sync(tas_priv->regmap); + if (ret) { + dev_err(tas_priv->dev, + "Failed to restore register cache: %d\n", ret); + goto out; + } + + tasdevice_prmg_load(tas_priv, 0); + tas_priv->cur_prog = 0; + + /* If calibrated data occurs error, dsp will still works with default + * calibrated data inside algo. + */ + if (tas_priv->cali_data.total_sz > calib_data_sz) + tas2781_apply_calib(tas_priv); + +out: + mutex_unlock(&tas_priv->codec_lock); + + return ret; +} + +static int tas2781_system_suspend(struct device *dev) +{ + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev); + int ret; + + dev_info(tas_priv->dev, "System Suspend\n"); + + ret = pm_runtime_force_suspend(dev); + if (ret) + return ret; + + /* Shutdown chip before system suspend */ + regcache_cache_only(tas_priv->regmap, false); + tasdevice_tuning_switch(tas_priv, 1); + regcache_cache_only(tas_priv->regmap, true); + regcache_mark_dirty(tas_priv->regmap); + /* + * Reset GPIO may be shared, so cannot reset here. + * However beyond this point, amps may be powered down. + */ + return 0; +} + +static int tas2781_system_resume(struct device *dev) +{ + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev); + unsigned long calib_data_sz = + tas_priv->ndev * TASDEVICE_SPEAKER_CALIBRATION_SIZE; + int i, ret; + + dev_info(tas_priv->dev, "System Resume\n"); + + ret = pm_runtime_force_resume(dev); + + mutex_lock(&tas_priv->codec_lock); + tas_priv->cur_prog = -1; + tas_priv->cur_conf = -1; + + for (i = 0; i < tas_priv->ndev; i++) { + tas_priv->tasdevice[i].cur_book = -1; + tas_priv->tasdevice[i].cur_prog = -1; + tas_priv->tasdevice[i].cur_conf = -1; + } + tas2781_reset(tas_priv); + tasdevice_prmg_load(tas_priv, 0); + tas_priv->cur_prog = 0; + + /* If calibrated data occurs error, dsp will still works with default + * calibrated data inside algo. + */ + if (tas_priv->cali_data.total_sz > calib_data_sz) + tas2781_apply_calib(tas_priv); + mutex_unlock(&tas_priv->codec_lock); + + return ret; +} + +static const struct dev_pm_ops tas2781_hda_pm_ops = { + RUNTIME_PM_OPS(tas2781_runtime_suspend, tas2781_runtime_resume, + NULL) + SYSTEM_SLEEP_PM_OPS(tas2781_system_suspend, tas2781_system_resume) +}; + +static const struct i2c_device_id tas2781_hda_i2c_id[] = { + { "tas2781-hda", 0 }, + {} +}; + +static const struct acpi_device_id tas2781_acpi_hda_match[] = { + {"TIAS2781", 0 }, + {} +}; +MODULE_DEVICE_TABLE(acpi, tas2781_acpi_hda_match); + +static struct i2c_driver tas2781_hda_i2c_driver = { + .driver = { + .name = "tas2781-hda", + .acpi_match_table = tas2781_acpi_hda_match, + .pm = &tas2781_hda_pm_ops, + }, + .id_table = tas2781_hda_i2c_id, + .probe_new = tas2781_hda_i2c_probe, + .remove = tas2781_hda_i2c_remove, +}; +module_i2c_driver(tas2781_hda_i2c_driver); + +MODULE_DESCRIPTION("TAS2781 HDA Driver"); +MODULE_AUTHOR("Shenghao Ding, TI, <shenghao-ding(a)ti.com>"); +MODULE_LICENSE("GPL"); +MODULE_IMPORT_NS(SND_SOC_TAS2781_FMWLIB); -- 2.34.1

1 0

[PATCH v2 4/5] ASoC: tas2781: Add tas2781 driver
by Shenghao Ding 08 May '23

08 May '23

Create tas2781 driver. Signed-off-by: Shenghao Ding <13916275206(a)139.com> --- Changes in v14: - fixed issue | Reported-by: kernel test robot <lkp(a)intel.com> | Link: https://lore.kernel.org/oe-kbuild-all/202305022033.LiI7Ojm4-lkp@intel.com/ - fixed issue | Reported-by: kernel test robot <lkp(a)intel.com> | Link: https://lore.kernel.org/oe-kbuild-all/202305022338.ZA1okoZW-lkp@intel.com/ Changes to be committed: modified: sound/soc/codecs/Kconfig modified: sound/soc/codecs/Makefile new file: sound/soc/codecs/tas2781-comlib.c new file: sound/soc/codecs/tas2781-i2c.c --- sound/soc/codecs/Kconfig | 24 + sound/soc/codecs/Makefile | 6 + sound/soc/codecs/tas2781-comlib.c | 581 ++++++++++++++++++++++++ sound/soc/codecs/tas2781-i2c.c | 705 ++++++++++++++++++++++++++++++ 4 files changed, 1316 insertions(+) create mode 100644 sound/soc/codecs/tas2781-comlib.c create mode 100644 sound/soc/codecs/tas2781-i2c.c diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 8020097d4e4c..7c9a55061663 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -234,6 +234,9 @@ config SND_SOC_ALL_CODECS imply SND_SOC_TAS2764 imply SND_SOC_TAS2770 imply SND_SOC_TAS2780 + imply SND_SOC_TAS2781_COMLIB + imply SND_SOC_TAS2781_FWLIB + imply SND_SOC_TAS2781 imply SND_SOC_TAS5086 imply SND_SOC_TAS571X imply SND_SOC_TAS5720 @@ -1699,6 +1702,27 @@ config SND_SOC_TAS2780 Enable support for Texas Instruments TAS2780 high-efficiency digital input mono Class-D audio power amplifiers. +config SND_SOC_TAS2781_COMLIB + select CRC8 + select REGMAP_I2C + tristate + +config SND_SOC_TAS2781_FMWLIB + tristate + default n + +config SND_SOC_TAS2781 + tristate "Texas Instruments TAS2781 speaker amplifier" + depends on I2C + select SND_SOC_TAS2781_COMLIB + select SND_SOC_TAS2781_FMWLIB + help + Enable support for Texas Instruments TAS2781 Smart Amplifier + Digital input mono Class-D and DSP-inside audio power amplifiers. + Note the TAS2781 driver implements a flexible and configurable + algo coefficient setting, for one, two or even multiple TAS2781 + chips. + config SND_SOC_TAS5086 tristate "Texas Instruments TAS5086 speaker amplifier" depends on I2C diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 5cdbae88e6e3..97c3881ed587 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -269,6 +269,9 @@ snd-soc-tas5805m-objs := tas5805m.o snd-soc-tas6424-objs := tas6424.o snd-soc-tda7419-objs := tda7419.o snd-soc-tas2770-objs := tas2770.o +snd-soc-tas2781-comlib-objs := tas2781-comlib.o +snd-soc-tas2781-fmwlib-objs := tas2781-fmwlib.o +snd-soc-tas2781-objs := tas2781-i2c.o snd-soc-tfa9879-objs := tfa9879.o snd-soc-tfa989x-objs := tfa989x.o snd-soc-tlv320adc3xxx-objs := tlv320adc3xxx.o @@ -633,6 +636,9 @@ obj-$(CONFIG_SND_SOC_TAS2552) += snd-soc-tas2552.o obj-$(CONFIG_SND_SOC_TAS2562) += snd-soc-tas2562.o obj-$(CONFIG_SND_SOC_TAS2764) += snd-soc-tas2764.o obj-$(CONFIG_SND_SOC_TAS2780) += snd-soc-tas2780.o +obj-$(CONFIG_SND_SOC_TAS2781_COMLIB) += snd-soc-tas2781-comlib.o +obj-$(CONFIG_SND_SOC_TAS2781_FMWLIB) += snd-soc-tas2781-fmwlib.o +obj-$(CONFIG_SND_SOC_TAS2781) += snd-soc-tas2781.o obj-$(CONFIG_SND_SOC_TAS5086) += snd-soc-tas5086.o obj-$(CONFIG_SND_SOC_TAS571X) += snd-soc-tas571x.o obj-$(CONFIG_SND_SOC_TAS5720) += snd-soc-tas5720.o diff --git a/sound/soc/codecs/tas2781-comlib.c b/sound/soc/codecs/tas2781-comlib.c new file mode 100644 index 000000000000..46deee71d549 --- /dev/null +++ b/sound/soc/codecs/tas2781-comlib.c @@ -0,0 +1,581 @@ +// SPDX-License-Identifier: GPL-2.0 +// +// tas2781-lib.c -- TAS2781 Common functions for HDA and ASoC Audio drivers +// +// Copyright 2023 Texas Instruments, Inc. +// +// Author: Shenghao Ding <shenghao-ding(a)ti.com> + +#include <linux/crc8.h> +#include <linux/firmware.h> +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_gpio.h> +#include <linux/of_irq.h> +#include <linux/regmap.h> +#include <linux/slab.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/tas2781.h> + +#define TASDEVICE_CRC8_POLYNOMIAL 0x4d + +static const struct regmap_range_cfg tasdevice_ranges[] = { + { + .range_min = 0, + .range_max = 256 * 128, + .selector_reg = TASDEVICE_PAGE_SELECT, + .selector_mask = 0xff, + .selector_shift = 0, + .window_start = 0, + .window_len = 128, + }, +}; + +static const struct regmap_config tasdevice_regmap = { + .reg_bits = 16, + .val_bits = 8, + .cache_type = REGCACHE_RBTREE, + .ranges = tasdevice_ranges, + .num_ranges = ARRAY_SIZE(tasdevice_ranges), + .max_register = 256 * 128, +}; + +static int tasdevice_change_chn_book(struct tasdevice_priv *tas_priv, + enum channel chn, int book) +{ + struct i2c_client *client = (struct i2c_client *)tas_priv->client; + int ret = 0; + int i; + + if (chn < tas_priv->ndev) { + struct tasdevice *tasdev = &tas_priv->tasdevice[chn]; + + if (tas_priv->glb_addr.ref_cnt != 0) { + tas_priv->glb_addr.ref_cnt = 0; + tas_priv->glb_addr.cur_book = -1; + } + client->addr = tasdev->dev_addr; + if (tasdev->cur_book != book) { + ret = regmap_write(tas_priv->regmap, + TASDEVICE_BOOKCTL_REG, book); + if (ret < 0) { + dev_err(tas_priv->dev, "%s, E=%d\n", + __func__, ret); + goto out; + } + tasdev->cur_book = book; + } + } else if (chn == tas_priv->ndev) { + struct global_addr *glb_addr = &tas_priv->glb_addr; + + /* Chn == device number will enable global broadcast mode*/ + if (tas_priv->glb_addr.ref_cnt == 0) + for (i = 0; i < tas_priv->ndev; i++) + tas_priv->tasdevice[i].cur_book = -1; + client->addr = glb_addr->dev_addr; + if (glb_addr->cur_book != book) { + ret = regmap_write(tas_priv->regmap, + TASDEVICE_BOOKCTL_REG, book); + if (ret < 0) { + dev_err(tas_priv->dev, "%s, book%x, E=%d\n", + __func__, book, ret); + goto out; + } + glb_addr->cur_book = book; + } + + glb_addr->ref_cnt++; + } else { + ret = -EINVAL; + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + } + +out: + return ret; +} + +int tasdevice_dev_read(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned int *val) +{ + int ret = 0; + + if (chn < tas_priv->ndev) { + ret = tasdevice_change_chn_book(tas_priv, chn, + TASDEVICE_BOOK_ID(reg)); + if (ret < 0) + goto out; + + ret = regmap_read(tas_priv->regmap, TASDEVICE_PGRG(reg), val); + if (ret < 0) + dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret); + } else { + ret = -EINVAL; + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + } + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_dev_read); + +int tasdevice_dev_write(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned int value) +{ + int ret = 0; + + /* chn <= tas_dev->ndev will support global broadcast mode*/ + if (chn <= tas_priv->ndev) { + ret = tasdevice_change_chn_book(tas_priv, chn, + TASDEVICE_BOOK_ID(reg)); + if (ret < 0) + goto out; + + ret = regmap_write(tas_priv->regmap, TASDEVICE_PGRG(reg), + value); + if (ret < 0) + dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret); + } else { + ret = -EINVAL; + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + } + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_dev_write); + +int tasdevice_dev_bulk_write( + struct tasdevice_priv *tas_priv, enum channel chn, + unsigned int reg, unsigned char *data, + unsigned int len) +{ + int ret = 0; + + /* chn <= tas_dev->ndev will support global broadcast mode*/ + if (chn <= tas_priv->ndev) { + ret = tasdevice_change_chn_book(tas_priv, chn, + TASDEVICE_BOOK_ID(reg)); + if (ret < 0) + goto out; + + ret = regmap_bulk_write(tas_priv->regmap, TASDEVICE_PGRG(reg), + data, len); + if (ret < 0) + dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret); + } else { + ret = -EINVAL; + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + } + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_dev_bulk_write); + +int tasdevice_dev_bulk_read(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned char *data, + unsigned int len) +{ + int ret = 0; + + if (chn < tas_priv->ndev) { + ret = tasdevice_change_chn_book(tas_priv, chn, + TASDEVICE_BOOK_ID(reg)); + if (ret < 0) + goto out; + + ret = regmap_bulk_read(tas_priv->regmap, TASDEVICE_PGRG(reg), + data, len); + if (ret < 0) + dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret); + } else + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_dev_bulk_read); + +int tasdevice_dev_update_bits( + struct tasdevice_priv *tas_priv, enum channel chn, + unsigned int reg, unsigned int mask, unsigned int value) +{ + int ret = 0; + + /* update-bits can't support global broadcast mode, + * because this operation contains a reading operation + * for register value. In global mode, reading register + * from all of the tas2781 will cause confusion. + */ + if (chn < tas_priv->ndev) { + ret = tasdevice_change_chn_book(tas_priv, chn, + TASDEVICE_BOOK_ID(reg)); + if (ret < 0) + goto out; + + ret = regmap_update_bits(tas_priv->regmap, + TASDEVICE_PGRG(reg), mask, value); + if (ret < 0) + dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret); + } else { + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + ret = -EINVAL; + } + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_dev_update_bits); + +/* Only register write and bulk write support global mode + * Other cases, such as bits update, register read and bulk + * only support device-by-device operation + */ +static void tas2781_set_global_mode(struct tasdevice_priv *tas_priv) +{ + int i, ret; + + for (i = 0; i < tas_priv->ndev; i++) { + ret = tasdevice_dev_update_bits(tas_priv, i, + TAS2781_MISC_CFG2, TAS2781_GLOBAL_ADDR_MASK, + TAS2781_GLOBAL_ADDR_ENABLE); + if (ret < 0) { + dev_err(tas_priv->dev, "%s: chn %d set glb fail, %d\n", + __func__, i, ret); + continue; + } + } +} + +struct tasdevice_priv *tasdevice_kzalloc(struct i2c_client *i2c) +{ + struct tasdevice_priv *tas_priv; + + tas_priv = devm_kzalloc(&i2c->dev, sizeof(*tas_priv), GFP_KERNEL); + if (!tas_priv) + return NULL; + tas_priv->dev = &i2c->dev; + tas_priv->client = (void *)i2c; + + return tas_priv; +} +EXPORT_SYMBOL_GPL(tasdevice_kzalloc); + +void tas2781_reset(struct tasdevice_priv *tas_dev) +{ + int ret, i; + + if (tas_dev->reset) { + gpiod_set_value_cansleep(tas_dev->reset, 0); + usleep_range(500, 1000); + gpiod_set_value_cansleep(tas_dev->reset, 1); + } else { + for (i = 0; i < tas_dev->ndev; i++) { + ret = tasdevice_dev_write(tas_dev, i, + TAS2781_REG_SWRESET, + TAS2781_REG_SWRESET_RESET); + if (ret < 0) + dev_err(tas_dev->dev, + "dev %d swreset fail, %d\n", + i, ret); + } + } + usleep_range(1000, 1050); +} +EXPORT_SYMBOL_GPL(tas2781_reset); + +int tascodec_init(struct tasdevice_priv *tas_priv, void *codec, + void (*cont)(const struct firmware *fw, void *context)) +{ + int ret = 0; + + /* Codec Lock Hold to ensure that codec_probe and firmware parsing and + * loading do not simultaneously execute. + */ + mutex_lock(&tas_priv->codec_lock); + + scnprintf(tas_priv->rca_binaryname, 64, "%srca%d.bin", + tas_priv->dev_name, tas_priv->ndev); + crc8_populate_msb(tas_priv->crc8_lkp_tbl, TASDEVICE_CRC8_POLYNOMIAL); + tas_priv->codec = codec; + ret = request_firmware_nowait(THIS_MODULE, FW_ACTION_UEVENT, + tas_priv->rca_binaryname, tas_priv->dev, GFP_KERNEL, tas_priv, + cont); + if (ret) + dev_err(tas_priv->dev, "request_firmware_nowait err:0x%08x\n", + ret); + + tas2781_reset(tas_priv); + if (tas_priv->set_global_mode) + tas_priv->set_global_mode(tas_priv); + + /* Codec Lock Release*/ + mutex_unlock(&tas_priv->codec_lock); + return ret; +} +EXPORT_SYMBOL_GPL(tascodec_init); + +int tasdevice_init(struct tasdevice_priv *tas_priv) +{ + int ret = 0; + int i; + + tas_priv->regmap = devm_regmap_init_i2c(tas_priv->client, + &tasdevice_regmap); + if (IS_ERR(tas_priv->regmap)) { + ret = PTR_ERR(tas_priv->regmap); + dev_err(tas_priv->dev, "Failed to allocate register map: %d\n", + ret); + goto out; + } + + tas_priv->cur_prog = -1; + tas_priv->cur_conf = -1; + + for (i = 0; i < tas_priv->ndev; i++) { + tas_priv->tasdevice[i].cur_book = -1; + tas_priv->tasdevice[i].cur_prog = -1; + tas_priv->tasdevice[i].cur_conf = -1; + } + + if (tas_priv->glb_addr.dev_addr != 0 + && tas_priv->glb_addr.dev_addr < 0x7F) + tas_priv->set_global_mode = tas2781_set_global_mode; + dev_set_drvdata(tas_priv->dev, tas_priv); + + mutex_init(&tas_priv->codec_lock); + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_init); + +static void tasdev_dsp_prog_blk_remove(struct tasdevice_prog *prog) +{ + struct tasdevice_data *im; + struct tasdev_blk *blk; + unsigned int nr_blk; + + if (!prog) + return; + + im = &(prog->dev_data); + + if (!im->dev_blks) + return; + + for (nr_blk = 0; nr_blk < im->nr_blk; nr_blk++) { + blk = &(im->dev_blks[nr_blk]); + kfree(blk->data); + } + kfree(im->dev_blks); +} + +static void tasdev_dsp_prog_remove(struct tasdevice_prog *prog, + unsigned short nr) +{ + int i; + + for (i = 0; i < nr; i++) + tasdev_dsp_prog_blk_remove(&prog[i]); + kfree(prog); +} + +static void tasdev_dsp_cfg_blk_remove(struct tasdevice_config *cfg) +{ + struct tasdevice_data *im; + struct tasdev_blk *blk; + unsigned int nr_blk; + + if (cfg) { + im = &(cfg->dev_data); + + if (!im->dev_blks) + return; + + for (nr_blk = 0; nr_blk < im->nr_blk; nr_blk++) { + blk = &(im->dev_blks[nr_blk]); + kfree(blk->data); + } + kfree(im->dev_blks); + } +} + +static void tasdev_dsp_cfg_remove(struct tasdevice_config *config, + unsigned short nr) +{ + int i; + + for (i = 0; i < nr; i++) + tasdev_dsp_cfg_blk_remove(&config[i]); + kfree(config); +} + +void tasdevice_dsp_remove(void *context) +{ + struct tasdevice_priv *tas_dev = (struct tasdevice_priv *) context; + struct tasdevice_fw *tas_fmw = tas_dev->fmw; + + if (!tas_dev->fmw) + return; + + if (tas_fmw->programs) + tasdev_dsp_prog_remove(tas_fmw->programs, + tas_fmw->nr_programs); + if (tas_fmw->configs) + tasdev_dsp_cfg_remove(tas_fmw->configs, + tas_fmw->nr_configurations); + kfree(tas_fmw); + tas_dev->fmw = NULL; +} +EXPORT_SYMBOL_GPL(tasdevice_dsp_remove); + +void tasdevice_remove(struct tasdevice_priv *tas_priv) +{ + if (gpio_is_valid(tas_priv->irq_info.irq_gpio)) + gpio_free(tas_priv->irq_info.irq_gpio); + kfree(tas_priv->acpi_subsystem_id); + mutex_destroy(&tas_priv->codec_lock); +} +EXPORT_SYMBOL_GPL(tasdevice_remove); + +static int tasdevice_clamp(int val, int max, unsigned int invert) +{ + if (val > max) + val = max; + if (invert) + val = max - val; + if (val < 0) + val = 0; + return val; +} + +int tasdevice_amp_putvol(struct tasdevice_priv *tas_priv, + struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc) +{ + unsigned int invert = mc->invert; + unsigned char mask; + int max = mc->max; + int err_cnt = 0; + int val, i, ret; + + mask = (1 << fls(max)) - 1; + mask <<= mc->shift; + val = tasdevice_clamp(ucontrol->value.integer.value[0], max, invert); + for (i = 0; i < tas_priv->ndev; i++) { + ret = tasdevice_dev_update_bits(tas_priv, i, + mc->reg, mask, (unsigned int)(val << mc->shift)); + if (!ret) + continue; + err_cnt++; + dev_err(tas_priv->dev, "set AMP vol error in dev %d\n", i); + } + + /* All the devices set error, return 0 */ + return (err_cnt == tas_priv->ndev) ? 0 : 1; +} +EXPORT_SYMBOL_GPL(tasdevice_amp_putvol); + +int tasdevice_amp_getvol(struct tasdevice_priv *tas_priv, + struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc) +{ + unsigned int invert = mc->invert; + unsigned char mask = 0; + int max = mc->max; + int ret = 0; + int val; + + /* Read the primary device */ + ret = tasdevice_dev_read(tas_priv, 0, mc->reg, &val); + if (ret) { + dev_err(tas_priv->dev, "%s, get AMP vol error\n", __func__); + goto out; + } + + mask = (1 << fls(max)) - 1; + mask <<= mc->shift; + val = (val & mask) >> mc->shift; + val = tasdevice_clamp(val, max, invert); + ucontrol->value.integer.value[0] = val; + +out: + return ret; + +} +EXPORT_SYMBOL_GPL(tasdevice_amp_getvol); + +int tasdevice_digital_putvol(struct tasdevice_priv *tas_priv, + struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc) +{ + unsigned int invert = mc->invert; + int max = mc->max; + int err_cnt = 0; + int ret = 1; + int val, i; + + val = tasdevice_clamp(ucontrol->value.integer.value[0], max, invert); + + if (tas_priv->set_global_mode) { + ret = tasdevice_dev_write(tas_priv, tas_priv->ndev, + mc->reg, (unsigned int)val); + if (ret) + dev_err(tas_priv->dev, "%s, error in global mode\n", + __func__); + } + + if (!tas_priv->set_global_mode || ret != 0) { + for (i = 0; i < tas_priv->ndev; i++) { + ret = tasdevice_dev_write(tas_priv, i, mc->reg, + (unsigned int)val); + if (!ret) + continue; + err_cnt++; + dev_err(tas_priv->dev, + "set digital vol err in dev %d\n", i); + } + } + + /* All the devices set error, return 0 */ + return (err_cnt == tas_priv->ndev) ? 0 : 1; + +} +EXPORT_SYMBOL_GPL(tasdevice_digital_putvol); + +int tasdevice_digital_getvol(struct tasdevice_priv *tas_priv, + struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc) +{ + unsigned int invert = mc->invert; + int max = mc->max; + int ret, val; + + /* Read the primary device as the whole */ + ret = tasdevice_dev_read(tas_priv, 0, mc->reg, &val); + if (ret) { + dev_err(tas_priv->dev, "%s, get digital vol error\n", + __func__); + goto out; + } + + val = tasdevice_clamp(val, max, invert); + ucontrol->value.integer.value[0] = val; + +out: + return ret; + +} +EXPORT_SYMBOL_GPL(tasdevice_digital_getvol); + +MODULE_DESCRIPTION("TAS2781 common library"); +MODULE_AUTHOR("Shenghao Ding, TI, <shenghao-ding(a)ti.com>"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/tas2781-i2c.c b/sound/soc/codecs/tas2781-i2c.c new file mode 100644 index 000000000000..0d34a7253dc3 --- /dev/null +++ b/sound/soc/codecs/tas2781-i2c.c @@ -0,0 +1,705 @@ +// SPDX-License-Identifier: GPL-2.0 +// +// ALSA SoC Texas Instruments TAS2781 Audio Smart Amplifier +// +// Copyright (C) 2022 - 2023 Texas Instruments Incorporated +// https://www.ti.com +// +// The TAS2781 driver implements a flexible and configurable +// algo coefficient setting for one, two, or even multiple +// TAS2781 chips. +// +// Author: Shenghao Ding <shenghao-ding(a)ti.com> +// Author: Kevin Lu <kevin-lu(a)ti.com> +// + +#include <linux/crc8.h> +#include <linux/firmware.h> +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_gpio.h> +#include <linux/of_irq.h> +#include <linux/regmap.h> +#include <linux/slab.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/tas2781.h> +#include <sound/tlv.h> +#include <sound/tas2781-tlv.h> + +static const struct i2c_device_id tasdevice_id[] = { + { "tas2781", TAS2781 }, + {} +}; +MODULE_DEVICE_TABLE(i2c, tasdevice_id); + +#ifdef CONFIG_OF +static const struct of_device_id tasdevice_of_match[] = { + { .compatible = "ti,tas2781" }, + {}, +}; +MODULE_DEVICE_TABLE(of, tasdevice_of_match); +#endif + +/** + * tas2781_digital_getvol - get the volum control + * @kcontrol: control pointer + * @ucontrol: User data + * Customer Kcontrol for tas2781 is primarily for regmap booking, paging + * depends on internal regmap mechanism. + * tas2781 contains book and page two-level register map, especially + * book switching will set the register BXXP00R7F, after switching to the + * correct book, then leverage the mechanism for paging to access the + * register. + */ +static int tas2781_digital_getvol(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + + return tasdevice_digital_getvol(tas_priv, ucontrol, mc); +} + +static int tas2781_digital_putvol(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + + return tasdevice_digital_putvol(tas_priv, ucontrol, mc); +} + +static int tas2781_amp_getvol(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + + return tasdevice_amp_getvol(tas_priv, ucontrol, mc); +} + +static int tas2781_amp_putvol(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = + snd_soc_component_get_drvdata(codec); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + + return tasdevice_amp_putvol(tas_priv, ucontrol, mc); +} + +static const struct snd_kcontrol_new tas2781_snd_controls[] = { + SOC_SINGLE_RANGE_EXT_TLV("Amp Gain Volume", TAS2781_AMP_LEVEL, + 1, 0, 20, 0, tas2781_amp_getvol, + tas2781_amp_putvol, amp_vol_tlv), + SOC_SINGLE_RANGE_EXT_TLV("Digital Volume", TAS2781_DVC_LVL, + 0, 0, 200, 1, tas2781_digital_getvol, + tas2781_digital_putvol, dvc_tlv), +}; + +static int tasdevice_set_profile_id(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + + tas_priv->rcabin.profile_cfg_id = ucontrol->value.integer.value[0]; + + return 1; +} + +static int tasdevice_info_programs(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + struct tasdevice_fw *tas_fw = tas_priv->fmw; + + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = 1; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = (int)tas_fw->nr_programs; + + return 0; +} + +static int tasdevice_info_configurations( + struct snd_kcontrol *kcontrol, struct snd_ctl_elem_info *uinfo) +{ + struct snd_soc_component *codec = + snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + struct tasdevice_fw *tas_fw = tas_priv->fmw; + + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = 1; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = (int)tas_fw->nr_configurations - 1; + + return 0; +} + +static int tasdevice_info_profile(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = 1; + uinfo->value.integer.min = 1; + uinfo->value.integer.max = max(0, tas_priv->rcabin.ncfgs); + + return 0; +} + +static int tasdevice_get_profile_id(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + + ucontrol->value.integer.value[0] = tas_priv->rcabin.profile_cfg_id; + + return 0; +} + +static int tasdevice_create_control(struct tasdevice_priv *tas_priv) +{ + struct snd_kcontrol_new *prof_ctrls; + int nr_controls = 1; + int mix_index = 0; + int ret; + char *name; + + prof_ctrls = devm_kcalloc(tas_priv->dev, nr_controls, + sizeof(prof_ctrls[0]), GFP_KERNEL); + if (!prof_ctrls) { + ret = -ENOMEM; + goto out; + } + + /* Create a mixer item for selecting the active profile */ + name = devm_kzalloc(tas_priv->dev, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, + GFP_KERNEL); + if (!name) { + ret = -ENOMEM; + goto out; + } + scnprintf(name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, "tasdev-profile-id"); + prof_ctrls[mix_index].name = name; + prof_ctrls[mix_index].iface = SNDRV_CTL_ELEM_IFACE_MIXER; + prof_ctrls[mix_index].info = tasdevice_info_profile; + prof_ctrls[mix_index].get = tasdevice_get_profile_id; + prof_ctrls[mix_index].put = tasdevice_set_profile_id; + mix_index++; + + ret = snd_soc_add_component_controls(tas_priv->codec, + prof_ctrls, nr_controls < mix_index ? nr_controls : mix_index); + +out: + return ret; +} + +static int tasdevice_program_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + + ucontrol->value.integer.value[0] = tas_priv->cur_prog; + + return 0; +} + +static int tasdevice_program_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + unsigned int nr_program = ucontrol->value.integer.value[0]; + + tas_priv->cur_prog = nr_program; + + return 1; +} + +static int tasdevice_configuration_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + + ucontrol->value.integer.value[0] = tas_priv->cur_conf; + + return 0; +} + +static int tasdevice_configuration_put( + struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + unsigned int nr_configuration = ucontrol->value.integer.value[0]; + + tas_priv->cur_conf = nr_configuration; + + return 1; +} + +static int tasdevice_dsp_create_ctrls( + struct tasdevice_priv *tas_priv) +{ + struct snd_kcontrol_new *dsp_ctrls; + char *prog_name, *conf_name; + int nr_controls = 2; + int mix_index = 0; + int ret; + + /* Alloc kcontrol via devm_kzalloc, which don't manually + * free the kcontrol + */ + dsp_ctrls = devm_kcalloc(tas_priv->dev, nr_controls, + sizeof(dsp_ctrls[0]), GFP_KERNEL); + if (!dsp_ctrls) { + ret = -ENOMEM; + goto out; + } + + /* Create a mixer item for selecting the active profile */ + prog_name = devm_kzalloc(tas_priv->dev, + SNDRV_CTL_ELEM_ID_NAME_MAXLEN, GFP_KERNEL); + conf_name = devm_kzalloc(tas_priv->dev, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, + GFP_KERNEL); + if (!prog_name || !conf_name) { + ret = -ENOMEM; + goto out; + } + + scnprintf(prog_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, + "tasdev-prog-id"); + dsp_ctrls[mix_index].name = prog_name; + dsp_ctrls[mix_index].iface = SNDRV_CTL_ELEM_IFACE_MIXER; + dsp_ctrls[mix_index].info = tasdevice_info_programs; + dsp_ctrls[mix_index].get = tasdevice_program_get; + dsp_ctrls[mix_index].put = tasdevice_program_put; + mix_index++; + + scnprintf(conf_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, + "tasdev-conf-id"); + dsp_ctrls[mix_index].name = conf_name; + dsp_ctrls[mix_index].iface = SNDRV_CTL_ELEM_IFACE_MIXER; + dsp_ctrls[mix_index].info = tasdevice_info_configurations; + dsp_ctrls[mix_index].get = tasdevice_configuration_get; + dsp_ctrls[mix_index].put = tasdevice_configuration_put; + mix_index++; + + ret = snd_soc_add_component_controls(tas_priv->codec, dsp_ctrls, + nr_controls < mix_index ? nr_controls : mix_index); + +out: + return ret; +} + +static void tasdevice_fw_ready(const struct firmware *fmw, + void *context) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)context; + int ret = 0; + int i; + + mutex_lock(&tas_priv->codec_lock); + + ret = tasdevice_rca_parser(tas_priv, fmw); + if (ret) + goto out; + tasdevice_create_control(tas_priv); + + tasdevice_dsp_remove(tas_priv); + tasdevice_calbin_remove(tas_priv); + tas_priv->fw_state = TASDEVICE_DSP_FW_PENDING; + scnprintf(tas_priv->coef_binaryname, 64, "%s_coef.bin", + tas_priv->dev_name); + ret = tasdevice_dsp_parser(tas_priv); + if (ret) { + dev_err(tas_priv->dev, "dspfw load %s error\n", + tas_priv->coef_binaryname); + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + goto out; + } + tasdevice_dsp_create_ctrls(tas_priv); + + tas_priv->fw_state = TASDEVICE_DSP_FW_ALL_OK; + + /* If calibrated data occurs error, dsp will still works with default + * calibrated data inside algo. + */ + for (i = 0; i < tas_priv->ndev; i++) { + scnprintf(tas_priv->cal_binaryname[i], 64, "%s_cal_0x%02x.bin", + tas_priv->dev_name, tas_priv->tasdevice[i].dev_addr); + ret = tas2781_load_calibration(tas_priv, + tas_priv->cal_binaryname[i], i); + if (ret != 0) + dev_err(tas_priv->dev, + "%s: load %s error, default will effect\n", + __func__, tas_priv->cal_binaryname[i]); + } + + tasdevice_prmg_calibdata_load(tas_priv, 0); + tas_priv->cur_prog = 0; +out: + if (tas_priv->fw_state == TASDEVICE_DSP_FW_FAIL) { + /*If DSP FW fail, kcontrol won't be created */ + tasdevice_config_info_remove(tas_priv); + tasdevice_dsp_remove(tas_priv); + } + mutex_unlock(&tas_priv->codec_lock); + if (fmw) + release_firmware(fmw); +} + +static int tasdevice_dapm_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *codec = snd_soc_dapm_to_component(w->dapm); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + int state = 0; + + /* Codec Lock Hold */ + mutex_lock(&tas_priv->codec_lock); + if (event == SND_SOC_DAPM_PRE_PMD) + state = 1; + tasdevice_tuning_switch(tas_priv, state); + /* Codec Lock Release*/ + mutex_unlock(&tas_priv->codec_lock); + + return 0; +} + +static const struct snd_soc_dapm_widget tasdevice_dapm_widgets[] = { + SND_SOC_DAPM_AIF_IN("ASI", "ASI Playback", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_OUT_E("ASI OUT", "ASI Capture", 0, SND_SOC_NOPM, + 0, 0, tasdevice_dapm_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_SPK("SPK", tasdevice_dapm_event), + SND_SOC_DAPM_OUTPUT("OUT"), + SND_SOC_DAPM_INPUT("DMIC") +}; + +static const struct snd_soc_dapm_route tasdevice_audio_map[] = { + {"SPK", NULL, "ASI"}, + {"OUT", NULL, "SPK"}, + {"ASI OUT", NULL, "DMIC"} +}; + +static int tasdevice_startup(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct snd_soc_component *codec = dai->component; + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + int ret = 0; + + if (tas_priv->fw_state != TASDEVICE_DSP_FW_ALL_OK) { + dev_err(tas_priv->dev, "DSP bin file not loaded\n"); + ret = -EINVAL; + } + + return ret; +} + +static int tasdevice_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, struct snd_soc_dai *dai) +{ + struct tasdevice_priv *tas_priv = snd_soc_dai_get_drvdata(dai); + unsigned int slot_width; + unsigned int fsrate; + int bclk_rate; + int rc = 0; + + fsrate = params_rate(params); + switch (fsrate) { + case 48000: + case 44100: + break; + default: + dev_err(tas_priv->dev, "%s: incorrect sample rate = %u\n", + __func__, fsrate); + rc = -EINVAL; + goto out; + } + + slot_width = params_width(params); + switch (slot_width) { + case 16: + case 20: + case 24: + case 32: + break; + default: + dev_err(tas_priv->dev, "%s: incorrect slot width = %u\n", + __func__, slot_width); + rc = -EINVAL; + goto out; + } + + bclk_rate = snd_soc_params_to_bclk(params); + if (bclk_rate < 0) { + dev_err(tas_priv->dev, "%s: incorrect bclk rate = %d\n", + __func__, bclk_rate); + rc = bclk_rate; + goto out; + } + +out: + return rc; +} + +static int tasdevice_set_dai_sysclk(struct snd_soc_dai *codec_dai, + int clk_id, unsigned int freq, int dir) +{ + struct tasdevice_priv *tas_priv = snd_soc_dai_get_drvdata(codec_dai); + + tas_priv->sysclk = freq; + + return 0; +} + +static const struct snd_soc_dai_ops tasdevice_dai_ops = { + .startup = tasdevice_startup, + .hw_params = tasdevice_hw_params, + .set_sysclk = tasdevice_set_dai_sysclk, +}; + +static struct snd_soc_dai_driver tasdevice_dai_driver[] = { + { + .name = "tas2781_codec", + .id = 0, + .playback = { + .stream_name = "Playback", + .channels_min = 1, + .channels_max = 4, + .rates = TASDEVICE_RATES, + .formats = TASDEVICE_FORMATS, + }, + .capture = { + .stream_name = "Capture", + .channels_min = 1, + .channels_max = 4, + .rates = TASDEVICE_RATES, + .formats = TASDEVICE_FORMATS, + }, + .ops = &tasdevice_dai_ops, + .symmetric_rate = 1, + }, +}; + +static int tasdevice_codec_probe(struct snd_soc_component *codec) +{ + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + + return tascodec_init(tas_priv, codec, tasdevice_fw_ready); +} + +static void tasdevice_deinit(void *context) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + + tasdevice_config_info_remove(tas_priv); + tasdevice_dsp_remove(tas_priv); + tasdevice_calbin_remove(tas_priv); + tas_priv->fw_state = TASDEVICE_DSP_FW_PENDING; +} + +static void tasdevice_codec_remove( + struct snd_soc_component *codec) +{ + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + + tasdevice_deinit(tas_priv); +} + +static const struct snd_soc_component_driver + soc_codec_driver_tasdevice = { + .probe = tasdevice_codec_probe, + .remove = tasdevice_codec_remove, + .controls = tas2781_snd_controls, + .num_controls = ARRAY_SIZE(tas2781_snd_controls), + .dapm_widgets = tasdevice_dapm_widgets, + .num_dapm_widgets = ARRAY_SIZE(tasdevice_dapm_widgets), + .dapm_routes = tasdevice_audio_map, + .num_dapm_routes = ARRAY_SIZE(tasdevice_audio_map), + .idle_bias_on = 1, + .endianness = 1, +}; + +static void tasdevice_parse_dt(struct tasdevice_priv *tas_priv) +{ + struct i2c_client *client = (struct i2c_client *)tas_priv->client; + unsigned int dev_addrs[max_chn]; + int rc, i, ndev; + + if (tas_priv->isacpi) { + ndev = device_property_read_u32_array(&client->dev, + "ti,audio-slots", NULL, 0); + if (ndev <= 0) { + ndev = 1; + dev_addrs[0] = client->addr; + } else { + ndev = (ndev < ARRAY_SIZE(dev_addrs)) + ? ndev : ARRAY_SIZE(dev_addrs); + ndev = device_property_read_u32_array(&client->dev, + "ti,audio-slots", dev_addrs, ndev); + } + + tas_priv->irq_info.irq_gpio = + acpi_dev_gpio_irq_get(ACPI_COMPANION(&client->dev), 0); + } else { + struct device_node *np = tas_priv->dev->of_node; + + ndev = of_property_read_variable_u32_array(np, + "ti,audio-slots", dev_addrs, 0, ARRAY_SIZE(dev_addrs)); + if (ndev <= 0) { + ndev = 1; + dev_addrs[0] = client->addr; + } + tas_priv->irq_info.irq_gpio = of_irq_get(np, 0); + } + tas_priv->ndev = ndev; + for (i = 0; i < ndev; i++) + tas_priv->tasdevice[i].dev_addr = dev_addrs[i]; + + if (ndev > 1) { + rc = device_property_read_u32(&client->dev, + "ti,broadcast-addr", + &(tas_priv->glb_addr.dev_addr)); + if (rc) { + dev_err(tas_priv->dev, + "Looking up broadcast-addr failed %d\n", rc); + tas_priv->glb_addr.dev_addr = 0; + } + } + + tas_priv->reset = devm_gpiod_get_optional(&client->dev, + "reset-gpios", GPIOD_OUT_HIGH); + if (IS_ERR(tas_priv->reset)) + dev_err(tas_priv->dev, "%s Can't get reset GPIO\n", + __func__); + + strcpy(tas_priv->dev_name, tasdevice_id[tas_priv->chip_id].name); + + if (gpio_is_valid(tas_priv->irq_info.irq_gpio)) { + rc = gpio_request(tas_priv->irq_info.irq_gpio, + "AUDEV-IRQ"); + if (!rc) { + gpio_direction_input( + tas_priv->irq_info.irq_gpio); + + tas_priv->irq_info.irq = + gpio_to_irq(tas_priv->irq_info.irq_gpio); + } else + dev_err(tas_priv->dev, "%s: GPIO %d request error\n", + __func__, tas_priv->irq_info.irq_gpio); + } else + dev_err(tas_priv->dev, + "Looking up irq-gpio property failed %d\n", + tas_priv->irq_info.irq_gpio); +} + +static int tasdevice_i2c_probe(struct i2c_client *i2c) +{ + const struct i2c_device_id *id = i2c_match_id(tasdevice_id, i2c); + const struct acpi_device_id *acpi_id; + struct tasdevice_priv *tas_priv; + int ret; + + tas_priv = tasdevice_kzalloc(i2c); + if (!tas_priv) + return -ENOMEM; + + if (ACPI_HANDLE(&i2c->dev)) { + acpi_id = acpi_match_device(i2c->dev.driver->acpi_match_table, + &i2c->dev); + if (!acpi_id) { + dev_err(&i2c->dev, "No driver data\n"); + ret = -EINVAL; + goto err; + } + tas_priv->chip_id = acpi_id->driver_data; + tas_priv->isacpi = true; + } else { + tas_priv->chip_id = id ? id->driver_data : 0; + tas_priv->isacpi = false; + } + + tasdevice_parse_dt(tas_priv); + + ret = tasdevice_init(tas_priv); + if (ret) + goto err; + + ret = devm_snd_soc_register_component(tas_priv->dev, + &soc_codec_driver_tasdevice, + tasdevice_dai_driver, ARRAY_SIZE(tasdevice_dai_driver)); + if (ret) { + dev_err(tas_priv->dev, "%s: codec register error:0x%08x\n", + __func__, ret); + goto err; + } +err: + if (ret < 0) + tasdevice_remove(tas_priv); + return ret; +} + +static void tasdevice_i2c_remove(struct i2c_client *client) +{ + struct tasdevice_priv *tas_priv = i2c_get_clientdata(client); + + tasdevice_remove(tas_priv); +} + +#ifdef CONFIG_ACPI +static const struct acpi_device_id tasdevice_acpi_match[] = { + { "TAS2781", TAS2781 }, + {}, +}; + +MODULE_DEVICE_TABLE(acpi, tasdevice_acpi_match); +#endif + +static struct i2c_driver tasdevice_i2c_driver = { + .driver = { + .name = "tas2781-codec", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(tasdevice_of_match), +#ifdef CONFIG_ACPI + .acpi_match_table = ACPI_PTR(tasdevice_acpi_match), +#endif + }, + .probe = tasdevice_i2c_probe, + .remove = tasdevice_i2c_remove, + .id_table = tasdevice_id, +}; + +module_i2c_driver(tasdevice_i2c_driver); + +MODULE_AUTHOR("Shenghao Ding <shenghao-ding(a)ti.com>"); +MODULE_AUTHOR("Kevin Lu <kevin-lu(a)ti.com>"); +MODULE_DESCRIPTION("ASoC TAS2781 Driver"); +MODULE_LICENSE("GPL"); +MODULE_IMPORT_NS(SND_SOC_TAS2781_FMWLIB); -- 2.34.1

1 0

[PATCH v2 3/5] ASoC: tas2781: firmware lib
by Shenghao Ding 08 May '23

08 May '23

Create tas2781 firmware lib. Signed-off-by: Shenghao Ding <13916275206(a)139.com> --- Changes in v2: - fixed issue | Reported-by: kernel test robot <lkp(a)intel.com> | Link: https://lore.kernel.org/oe-kbuild-all/202305022033.LiI7Ojm4-lkp@intel.com/ - Move back to codecs folder, this firmware lib is special for the audio cases Changes to be committed: new file: sound/soc/codecs/tas2781-fmwlib.c --- sound/soc/codecs/tas2781-fmwlib.c | 2383 +++++++++++++++++++++++++++++ 1 file changed, 2383 insertions(+) create mode 100644 sound/soc/codecs/tas2781-fmwlib.c diff --git a/sound/soc/codecs/tas2781-fmwlib.c b/sound/soc/codecs/tas2781-fmwlib.c new file mode 100644 index 000000000000..b79d2ef7c77d --- /dev/null +++ b/sound/soc/codecs/tas2781-fmwlib.c @@ -0,0 +1,2383 @@ +// SPDX-License-Identifier: GPL-2.0 +// +// tasdevice-fmw.c -- TASDEVICE firmware support +// +// Copyright 2023 Texas Instruments, Inc. +// +// Author: Shenghao Ding <shenghao-ding(a)ti.com> + +#include <linux/crc8.h> +#include <linux/firmware.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_gpio.h> +#include <linux/of_irq.h> +#include <linux/regmap.h> +#include <linux/slab.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/tlv.h> +#include <sound/tas2781.h> + + +#define ERROR_PRAM_CRCCHK 0x0000000 +#define ERROR_YRAM_CRCCHK 0x0000001 +#define PPC_DRIVER_CRCCHK 0x00000200 + +#define TAS2781_SA_COEFF_SWAP_REG TASDEVICE_REG(0, 0x35, 0x2c) +#define TAS2781_YRAM_BOOK1 140 +#define TAS2781_YRAM1_PAGE 42 +#define TAS2781_YRAM1_START_REG 88 + +#define TAS2781_YRAM2_START_PAGE 43 +#define TAS2781_YRAM2_END_PAGE 49 +#define TAS2781_YRAM2_START_REG 8 +#define TAS2781_YRAM2_END_REG 127 + +#define TAS2781_YRAM3_PAGE 50 +#define TAS2781_YRAM3_START_REG 8 +#define TAS2781_YRAM3_END_REG 27 + +/*should not include B0_P53_R44-R47 */ +#define TAS2781_YRAM_BOOK2 0 +#define TAS2781_YRAM4_START_PAGE 50 +#define TAS2781_YRAM4_END_PAGE 60 + +#define TAS2781_YRAM5_PAGE 61 +#define TAS2781_YRAM5_START_REG TAS2781_YRAM3_START_REG +#define TAS2781_YRAM5_END_REG TAS2781_YRAM3_END_REG + +#define TASDEVICE_MAXPROGRAM_NUM_KERNEL 5 +#define TASDEVICE_MAXCONFIG_NUM_KERNEL_MULTIPLE_AMPS 64 +#define TASDEVICE_MAXCONFIG_NUM_KERNEL 10 +#define MAIN_ALL_DEVICES_1X 0x01 +#define MAIN_DEVICE_A_1X 0x02 +#define MAIN_DEVICE_B_1X 0x03 +#define MAIN_DEVICE_C_1X 0x04 +#define MAIN_DEVICE_D_1X 0x05 +#define COEFF_DEVICE_A_1X 0x12 +#define COEFF_DEVICE_B_1X 0x13 +#define COEFF_DEVICE_C_1X 0x14 +#define COEFF_DEVICE_D_1X 0x15 +#define PRE_DEVICE_A_1X 0x22 +#define PRE_DEVICE_B_1X 0x23 +#define PRE_DEVICE_C_1X 0x24 +#define PRE_DEVICE_D_1X 0x25 + +struct tas_crc { + unsigned char offset; + unsigned char len; +}; + +const char deviceNumber[TASDEVICE_DSP_TAS_MAX_DEVICE] = { + 1, 2, 1, 2, 1, 1, 0, 2, 4, 3, 1, 2, 3, 4 +}; + +static struct tasdevice_config_info *tasdevice_add_config( + struct tasdevice_priv *tas_priv, unsigned char *config_data, + unsigned int config_size, int *status) +{ + struct tasdevice_config_info *cfg_info; + struct tasdev_blk_data **bk_da; + unsigned int config_offset = 0; + unsigned int i; + + /* In most projects are many audio cases, such as music, handfree, + * receiver, games, audio-to-haptics, PMIC record, bypass mode, + * portrait, landscape, etc. Even in multiple audios, one or + * two of the chips will work for the special case, such as + * ultrasonic application. In order to support these variable-numbers + * of audio cases, flexible configs have been introduced in the + * dsp firmware. + */ + cfg_info = kzalloc(sizeof(struct tasdevice_config_info), GFP_KERNEL); + if (!cfg_info) { + *status = -ENOMEM; + goto out; + } + + if (tas_priv->rcabin.fw_hdr.binary_version_num >= 0x105) { + if (config_offset + 64 > (int)config_size) { + *status = -EINVAL; + dev_err(tas_priv->dev, "add conf: Out of boundary\n"); + goto out; + } + config_offset += 64; + } + + if (config_offset + 4 > (int)config_size) { + *status = -EINVAL; + dev_err(tas_priv->dev, "add config: Out of boundary\n"); + goto out; + } + + /* convert data[offset], data[offset + 1], data[offset + 2] and + * data[offset + 3] into host + */ + cfg_info->nblocks = + be32_to_cpup((__be32 *)&config_data[config_offset]); + config_offset += 4; + + /* Several kinds of dsp/algorithm firmwares can run on tas2781, + * the number and size of blk are not fixed and different among + * these firmwares. + */ + bk_da = cfg_info->blk_data = kcalloc(cfg_info->nblocks, + sizeof(struct tasdev_blk_data *), GFP_KERNEL); + if (!bk_da) { + *status = -ENOMEM; + goto out; + } + cfg_info->real_nblocks = 0; + for (i = 0; i < cfg_info->nblocks; i++) { + if (config_offset + 12 > config_size) { + *status = -EINVAL; + dev_err(tas_priv->dev, + "%s: Out of boundary: i = %d nblocks = %u!\n", + __func__, i, cfg_info->nblocks); + break; + } + bk_da[i] = kzalloc(sizeof(struct tasdev_blk_data), GFP_KERNEL); + if (!bk_da[i]) { + *status = -ENOMEM; + break; + } + + bk_da[i]->dev_idx = config_data[config_offset]; + config_offset++; + + bk_da[i]->block_type = config_data[config_offset]; + config_offset++; + + if (bk_da[i]->block_type == TASDEVICE_BIN_BLK_PRE_POWER_UP) { + if (bk_da[i]->dev_idx == 0) + cfg_info->active_dev = 1; + else + cfg_info->active_dev = 1 << + (bk_da[i]->dev_idx - 1); + + } + bk_da[i]->yram_checksum = + be16_to_cpup((__be16 *)&config_data[config_offset]); + config_offset += 2; + bk_da[i]->block_size = + be32_to_cpup((__be32 *)&config_data[config_offset]); + config_offset += 4; + + bk_da[i]->n_subblks = + be32_to_cpup((__be32 *)&config_data[config_offset]); + + config_offset += 4; + + if (config_offset + bk_da[i]->block_size > config_size) { + *status = -EINVAL; + dev_err(tas_priv->dev, + "%s: Out of boundary: i = %d blks = %u!\n", + __func__, i, cfg_info->nblocks); + break; + } + /* instead of kzalloc+memcpy */ + bk_da[i]->regdata = kmemdup(&config_data[config_offset], + bk_da[i]->block_size, GFP_KERNEL); + if (!bk_da[i]->regdata) { + *status = -ENOMEM; + goto out; + } + + config_offset += bk_da[i]->block_size; + cfg_info->real_nblocks += 1; + } + +out: + return cfg_info; +} + +int tasdevice_rca_parser(void *context, const struct firmware *fmw) +{ + struct tasdevice_priv *tas_priv = context; + struct tasdevice_config_info **cfg_info; + struct tasdevice_rca_hdr *fw_hdr; + struct tasdevice_rca *rca; + unsigned int total_config_sz = 0; + unsigned char *buf; + int offset = 0; + int ret = 0; + int i; + + rca = &(tas_priv->rcabin); + fw_hdr = &(rca->fw_hdr); + if (!fmw || !fmw->data) { + dev_err(tas_priv->dev, "Failed to read %s\n", + tas_priv->rca_binaryname); + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + ret = -EINVAL; + goto out; + } + buf = (unsigned char *)fmw->data; + + fw_hdr->img_sz = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + if (fw_hdr->img_sz != fmw->size) { + dev_err(tas_priv->dev, + "File size not match, %d %u", (int)fmw->size, + fw_hdr->img_sz); + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + ret = -EINVAL; + goto out; + } + + fw_hdr->checksum = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + fw_hdr->binary_version_num = be32_to_cpup((__be32 *)&buf[offset]); + if (fw_hdr->binary_version_num < 0x103) { + dev_err(tas_priv->dev, "File version 0x%04x is too low", + fw_hdr->binary_version_num); + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + ret = -EINVAL; + goto out; + } + offset += 4; + fw_hdr->drv_fw_version = be32_to_cpup((__be32 *)&buf[offset]); + offset += 8; + fw_hdr->plat_type = buf[offset]; + offset += 1; + fw_hdr->dev_family = buf[offset]; + offset += 1; + fw_hdr->reserve = buf[offset]; + offset += 1; + fw_hdr->ndev = buf[offset]; + offset += 1; + if (fw_hdr->ndev != tas_priv->ndev) { + dev_err(tas_priv->dev, + "ndev(%u) in rcabin mismatch ndev(%u) in DTS\n", + fw_hdr->ndev, tas_priv->ndev); + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + ret = -EINVAL; + goto out; + } + if (offset + TASDEVICE_DEVICE_SUM > fw_hdr->img_sz) { + dev_err(tas_priv->dev, "rca_ready: Out of boundary!\n"); + ret = -EINVAL; + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + goto out; + } + + for (i = 0; i < TASDEVICE_DEVICE_SUM; i++, offset++) + fw_hdr->devs[i] = buf[offset]; + + fw_hdr->nconfig = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + + for (i = 0; i < TASDEVICE_CONFIG_SUM; i++) { + fw_hdr->config_size[i] = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + total_config_sz += fw_hdr->config_size[i]; + } + + if (fw_hdr->img_sz - total_config_sz != (unsigned int)offset) { + dev_err(tas_priv->dev, "Bin file error!\n"); + ret = -EINVAL; + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + goto out; + } + + cfg_info = kcalloc(fw_hdr->nconfig, sizeof(*cfg_info), GFP_KERNEL); + if (!cfg_info) { + ret = -ENOMEM; + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + goto out; + } + rca->cfg_info = cfg_info; + rca->ncfgs = 0; + for (i = 0; i < (int)fw_hdr->nconfig; i++) { + rca->ncfgs += 1; + cfg_info[i] = tasdevice_add_config(tas_priv, &buf[offset], + fw_hdr->config_size[i], &ret); + if (ret) { + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + goto out; + } + offset += (int)fw_hdr->config_size[i]; + } +out: + return ret; +} +EXPORT_SYMBOL_NS_GPL(tasdevice_rca_parser, SND_SOC_TAS2781_FMWLIB); + +static int fw_parse_block_data_kernel(struct tasdevice_fw *tas_fmw, + struct tasdev_blk *block, const struct firmware *fmw, int offset) +{ + const unsigned char *data = fmw->data; + + if (offset + 16 > fmw->size) { + dev_err(tas_fmw->dev, "%s: File Size error\n", __func__); + offset = -EINVAL; + goto out; + } + + /* convert data[offset], data[offset + 1], data[offset + 2] and + * data[offset + 3] into host + */ + block->type = be32_to_cpup((__be32 *)&data[offset]); + offset += 4; + + block->is_pchksum_present = data[offset]; + offset++; + + block->pchksum = data[offset]; + offset++; + + block->is_ychksum_present = data[offset]; + offset++; + + block->ychksum = data[offset]; + offset++; + + block->blk_size = be32_to_cpup((__be32 *)&data[offset]); + offset += 4; + + block->nr_subblocks = be32_to_cpup((__be32 *)&data[offset]); + offset += 4; + + if (offset + block->blk_size > fmw->size) { + dev_err(tas_fmw->dev, "%s: nSublocks error\n", __func__); + offset = -EINVAL; + goto out; + } + /* instead of kzalloc+memcpy */ + block->data = kmemdup(&data[offset], block->blk_size, GFP_KERNEL); + if (!block->data) { + offset = -ENOMEM; + goto out; + } + offset += block->blk_size; + +out: + return offset; +} + +static int fw_parse_data_kernel(struct tasdevice_fw *tas_fmw, + struct tasdevice_data *img_data, const struct firmware *fmw, + int offset) +{ + const unsigned char *data = fmw->data; + struct tasdev_blk *blk; + unsigned int i; + + if (offset + 4 > fmw->size) { + dev_err(tas_fmw->dev, "%s: File Size error\n", __func__); + offset = -EINVAL; + goto out; + } + img_data->nr_blk = be32_to_cpup((__be32 *)&data[offset]); + offset += 4; + + img_data->dev_blks = kcalloc(img_data->nr_blk, + sizeof(struct tasdev_blk), GFP_KERNEL); + if (!img_data->dev_blks) { + offset = -ENOMEM; + goto out; + } + + for (i = 0; i < img_data->nr_blk; i++) { + blk = &(img_data->dev_blks[i]); + offset = fw_parse_block_data_kernel(tas_fmw, blk, fmw, offset); + if (offset < 0) { + offset = -EINVAL; + break; + } + } + +out: + return offset; +} + +static int fw_parse_program_data_kernel( + struct tasdevice_priv *tas_priv, struct tasdevice_fw *tas_fmw, + const struct firmware *fmw, int offset) +{ + struct tasdevice_prog *program; + unsigned int i; + + for (i = 0; i < tas_fmw->nr_programs; i++) { + program = &(tas_fmw->programs[i]); + if (offset + 72 > fmw->size) { + dev_err(tas_priv->dev, "%s: mpName error\n", __func__); + offset = -EINVAL; + goto out; + } + /*skip 72 unused byts*/ + offset += 72; + + offset = fw_parse_data_kernel(tas_fmw, &(program->dev_data), + fmw, offset); + if (offset < 0) + goto out; + } + +out: + return offset; +} + +static int fw_parse_configuration_data_kernel( + struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, const struct firmware *fmw, int offset) +{ + const unsigned char *data = fmw->data; + struct tasdevice_config *config; + unsigned int i; + + for (i = 0; i < tas_fmw->nr_configurations; i++) { + config = &(tas_fmw->configs[i]); + if (offset + 80 > fmw->size) { + dev_err(tas_priv->dev, "%s: mpName error\n", __func__); + offset = -EINVAL; + goto out; + } + memcpy(config->name, &data[offset], 64); + /*skip extra 16 bytes*/ + offset += 80; + + offset = fw_parse_data_kernel(tas_fmw, &(config->dev_data), + fmw, offset); + if (offset < 0) + goto out; + } + +out: + return offset; +} + +static int fw_parse_variable_header_kernel( + struct tasdevice_priv *tas_priv, const struct firmware *fmw, + int offset) +{ + struct tasdevice_fw *tas_fmw = tas_priv->fmw; + struct tasdevice_dspfw_hdr *fw_hdr = &(tas_fmw->fw_hdr); + struct tasdevice_prog *program; + struct tasdevice_config *config; + const unsigned char *buf = fmw->data; + unsigned short max_confs; + unsigned int i; + + if (offset + 12 + 4 * TASDEVICE_MAXPROGRAM_NUM_KERNEL > fmw->size) { + dev_err(tas_priv->dev, "%s: File Size error\n", __func__); + offset = -EINVAL; + goto out; + } + fw_hdr->device_family = be16_to_cpup((__be16 *)&buf[offset]); + if (fw_hdr->device_family != 0) { + dev_err(tas_priv->dev, "%s:not TAS device\n", __func__); + offset = -EINVAL; + goto out; + } + offset += 2; + fw_hdr->device = be16_to_cpup((__be16 *)&buf[offset]); + if (fw_hdr->device >= TASDEVICE_DSP_TAS_MAX_DEVICE || + fw_hdr->device == 6) { + dev_err(tas_priv->dev, "Unsupported dev %d\n", fw_hdr->device); + offset = -EINVAL; + goto out; + } + offset += 2; + fw_hdr->ndev = deviceNumber[fw_hdr->device]; + + if (fw_hdr->ndev != tas_priv->ndev) { + dev_err(tas_priv->dev, + "%s: ndev(%u) in dspbin mismatch ndev(%u) in DTS\n", + __func__, fw_hdr->ndev, tas_priv->ndev); + offset = -EINVAL; + goto out; + } + + tas_fmw->nr_programs = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + + if (tas_fmw->nr_programs == 0 || tas_fmw->nr_programs > + TASDEVICE_MAXPROGRAM_NUM_KERNEL) { + dev_err(tas_priv->dev, "mnPrograms is invalid\n"); + offset = -EINVAL; + goto out; + } + + tas_fmw->programs = kcalloc(tas_fmw->nr_programs, + sizeof(struct tasdevice_prog), GFP_KERNEL); + if (!tas_fmw->programs) { + offset = -ENOMEM; + goto out; + } + + for (i = 0; i < tas_fmw->nr_programs; i++) { + program = &(tas_fmw->programs[i]); + program->prog_size = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + } + + /* Skip the unused prog_size */ + offset += 4 * (TASDEVICE_MAXPROGRAM_NUM_KERNEL - tas_fmw->nr_programs); + + tas_fmw->nr_configurations = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + + /* The max number of config in firmware greater than 4 pieces of + * tas2781s is different from the one lower than 4 pieces of + * tas2781s. + */ + max_confs = (fw_hdr->ndev >= 4) ? + TASDEVICE_MAXCONFIG_NUM_KERNEL_MULTIPLE_AMPS : + TASDEVICE_MAXCONFIG_NUM_KERNEL; + if (tas_fmw->nr_configurations == 0 || + tas_fmw->nr_configurations > max_confs) { + dev_err(tas_priv->dev, "%s: Conf is invalid\n", __func__); + offset = -EINVAL; + goto out; + } + + if (offset + 4 * max_confs > fmw->size) { + dev_err(tas_priv->dev, "%s: mpConfigurations err\n", __func__); + offset = -EINVAL; + goto out; + } + + tas_fmw->configs = kcalloc(tas_fmw->nr_configurations, + sizeof(struct tasdevice_config), GFP_KERNEL); + if (!tas_fmw->configs) { + offset = -ENOMEM; + goto out; + } + + for (i = 0; i < tas_fmw->nr_programs; i++) { + config = &(tas_fmw->configs[i]); + config->cfg_size = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + } + + /* Skip the unused configs */ + offset += 4 * (max_confs - tas_fmw->nr_programs); + +out: + return offset; +} + +static int tasdevice_process_block(void *context, unsigned char *data, + unsigned char dev_idx, int sublocksize) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)context; + int subblk_offset, chn, chnend, rc; + unsigned char subblk_typ = data[1]; + int blktyp = dev_idx & 0xC0; + int idx = dev_idx & 0x3F; + bool is_err = false; + + if (idx) { + chn = idx - 1; + chnend = idx; + } else { + if (tas_priv->set_global_mode) { + chn = tas_priv->ndev; + chnend = tas_priv->ndev + 1; + } else { + chn = 0; + chnend = tas_priv->ndev; + } + } + + for (; chn < chnend; chn++) { + if (!tas_priv->set_global_mode && + tas_priv->tasdevice[chn].is_loading == false) + continue; + + is_err = false; + subblk_offset = 2; + switch (subblk_typ) { + case TASDEVICE_CMD_SING_W: { + int i; + unsigned short len = be16_to_cpup((__be16 *)&data[2]); + + subblk_offset += 2; + if (subblk_offset + 4 * len > sublocksize) { + dev_err(tas_priv->dev, + "process_block: Out of boundary\n"); + is_err = true; + break; + } + + for (i = 0; i < len; i++) { + rc = tasdevice_dev_write(tas_priv, chn, + TASDEVICE_REG(data[subblk_offset], + data[subblk_offset + 1], + data[subblk_offset + 2]), + data[subblk_offset + 3]); + if (rc < 0) { + is_err = true; + dev_err(tas_priv->dev, + "process_block: single write error\n"); + } + subblk_offset += 4; + } + } + break; + case TASDEVICE_CMD_BURST: { + unsigned short len = be16_to_cpup((__be16 *)&data[2]); + + subblk_offset += 2; + if (subblk_offset + 4 + len > sublocksize) { + dev_err(tas_priv->dev, + "%s: BST Out of boundary\n", + __func__); + is_err = true; + break; + } + if (len % 4) { + dev_err(tas_priv->dev, + "%s:Bst-len(%u)not div by 4\n", + __func__, len); + break; + } + + rc = tasdevice_dev_bulk_write(tas_priv, chn, + TASDEVICE_REG(data[subblk_offset], + data[subblk_offset + 1], + data[subblk_offset + 2]), + &(data[subblk_offset + 4]), len); + if (rc < 0) { + is_err = true; + dev_err(tas_priv->dev, + "%s: bulk_write error = %d\n", + __func__, rc); + } + subblk_offset += (len + 4); + } + break; + case TASDEVICE_CMD_DELAY: { + unsigned int sleep_time = 0; + + if (subblk_offset + 2 > sublocksize) { + dev_err(tas_priv->dev, + "%s: delay Out of boundary\n", + __func__); + is_err = true; + break; + } + sleep_time = be16_to_cpup((__be16 *)&data[2]) * 1000; + usleep_range(sleep_time, sleep_time + 50); + subblk_offset += 2; + } + break; + case TASDEVICE_CMD_FIELD_W: + if (subblk_offset + 6 > sublocksize) { + dev_err(tas_priv->dev, + "%s: bit write Out of boundary\n", + __func__); + is_err = true; + break; + } + rc = tasdevice_dev_update_bits(tas_priv, chn, + TASDEVICE_REG(data[subblk_offset + 2], + data[subblk_offset + 3], + data[subblk_offset + 4]), + data[subblk_offset + 1], + data[subblk_offset + 5]); + if (rc < 0) { + is_err = true; + dev_err(tas_priv->dev, + "%s: update_bits error = %d\n", + __func__, rc); + } + subblk_offset += 6; + break; + default: + break; + } + if (is_err == true && blktyp != 0) { + if (blktyp == 0x80) { + tas_priv->tasdevice[chn].cur_prog = -1; + tas_priv->tasdevice[chn].cur_conf = -1; + } else + tas_priv->tasdevice[chn].cur_conf = -1; + } + } + + return subblk_offset; +} + +void tasdevice_select_cfg_blk(void *pContext, int conf_no, + unsigned char block_type) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) pContext; + struct tasdevice_rca *rca = &(tas_priv->rcabin); + struct tasdevice_config_info **cfg_info = rca->cfg_info; + struct tasdev_blk_data **blk_data; + int j, k, chn, chnend; + + if (conf_no >= rca->ncfgs || conf_no < 0 || !cfg_info) { + dev_err(tas_priv->dev, "conf_no should be not more than %u\n", + rca->ncfgs); + return; + } + blk_data = cfg_info[conf_no]->blk_data; + + for (j = 0; j < (int)cfg_info[conf_no]->real_nblocks; j++) { + unsigned int length = 0, rc = 0; + + if (block_type > 5 || block_type < 2) { + dev_err(tas_priv->dev, + "block_type should be in range from 2 to 5\n"); + break; + } + if (block_type != blk_data[j]->block_type) + continue; + + for (k = 0; k < (int)blk_data[j]->n_subblks; k++) { + if (blk_data[j]->dev_idx) { + chn = blk_data[j]->dev_idx - 1; + chnend = blk_data[j]->dev_idx; + } else { + chn = 0; + chnend = tas_priv->ndev; + } + for (; chn < chnend; chn++) + tas_priv->tasdevice[chn].is_loading = true; + + rc = tasdevice_process_block(tas_priv, + blk_data[j]->regdata + length, + blk_data[j]->dev_idx, + blk_data[j]->block_size - length); + length += rc; + if (blk_data[j]->block_size < length) { + dev_err(tas_priv->dev, + "%s: %u %u out of boundary\n", + __func__, length, + blk_data[j]->block_size); + break; + } + } + if (length != blk_data[j]->block_size) + dev_err(tas_priv->dev, "%s: %u %u size is not same\n", + __func__, length, blk_data[j]->block_size); + } +} +EXPORT_SYMBOL_NS_GPL(tasdevice_select_cfg_blk, SND_SOC_TAS2781_FMWLIB); + +static int tasdevice_load_block_kernel( + struct tasdevice_priv *tasdevice, struct tasdev_blk *block) +{ + struct tasdevice_dspfw_hdr *fw_hdr = &(tasdevice->fmw->fw_hdr); + struct tasdevice_fw_fixed_hdr *fw_fixed_hdr = &(fw_hdr->fixed_hdr); + const unsigned int blk_size = block->blk_size; + unsigned int i, length; + unsigned char *data = block->data; + unsigned char dev_idx = 0; + + if (fw_fixed_hdr->ppcver >= PPC3_VERSION) { + switch (block->type) { + case MAIN_ALL_DEVICES_1X: + dev_idx = 0x80; + break; + case MAIN_DEVICE_A_1X: + dev_idx = 0x81; + break; + case COEFF_DEVICE_A_1X: + case PRE_DEVICE_A_1X: + dev_idx = 0xC1; + break; + case MAIN_DEVICE_B_1X: + dev_idx = 0x82; + break; + case COEFF_DEVICE_B_1X: + case PRE_DEVICE_B_1X: + dev_idx = 0xC2; + break; + case MAIN_DEVICE_C_1X: + dev_idx = 0x83; + break; + case COEFF_DEVICE_C_1X: + case PRE_DEVICE_C_1X: + dev_idx = 0xC3; + break; + case MAIN_DEVICE_D_1X: + dev_idx = 0x84; + break; + case COEFF_DEVICE_D_1X: + case PRE_DEVICE_D_1X: + dev_idx = 0xC4; + break; + default: + dev_info(tasdevice->dev, + "%s: load block: Other Type = 0x%02x\n", + __func__, block->type); + break; + } + } else { + switch (block->type) { + case MAIN_ALL_DEVICES: + dev_idx = 0|0x80; + break; + case MAIN_DEVICE_A: + dev_idx = 0x81; + break; + case COEFF_DEVICE_A: + case PRE_DEVICE_A: + dev_idx = 0xC1; + break; + case MAIN_DEVICE_B: + dev_idx = 0x82; + break; + case COEFF_DEVICE_B: + case PRE_DEVICE_B: + dev_idx = 0xC2; + break; + case MAIN_DEVICE_C: + dev_idx = 0x83; + break; + case COEFF_DEVICE_C: + case PRE_DEVICE_C: + dev_idx = 0xC3; + break; + case MAIN_DEVICE_D: + dev_idx = 0x84; + break; + case COEFF_DEVICE_D: + case PRE_DEVICE_D: + dev_idx = 0xC4; + break; + default: + dev_info(tasdevice->dev, + "%s: load block: Other Type = 0x%02x\n", + __func__, block->type); + break; + } + } + + for (i = 0, length = 0; i < block->nr_subblocks; i++) { + int rc = tasdevice_process_block(tasdevice, data + length, + dev_idx, blk_size - length); + if (rc < 0) { + dev_err(tasdevice->dev, + "%s: %u %u sublock write error\n", + __func__, length, blk_size); + break; + } + length += (unsigned int)rc; + if (blk_size < length) { + dev_err(tasdevice->dev, "%s: %u %u out of boundary\n", + __func__, length, blk_size); + break; + } + } + + return 0; +} + +static int fw_parse_variable_hdr(struct tasdevice_priv + *tas_priv, struct tasdevice_dspfw_hdr *fw_hdr, + const struct firmware *fmw, int offset) +{ + const unsigned char *buf = fmw->data; + int len = strlen((char *)&buf[offset]); + + len++; + + if (offset + len + 8 > fmw->size) { + dev_err(tas_priv->dev, "%s: File Size error\n", __func__); + offset = -EINVAL; + goto out; + } + + offset += len; + + fw_hdr->device_family = be32_to_cpup((__be32 *)&buf[offset]); + if (fw_hdr->device_family != 0) { + dev_err(tas_priv->dev, "%s: not TAS device\n", __func__); + offset = -EINVAL; + goto out; + } + offset += 4; + + fw_hdr->device = be32_to_cpup((__be32 *)&buf[offset]); + if (fw_hdr->device >= TASDEVICE_DSP_TAS_MAX_DEVICE || + fw_hdr->device == 6) { + dev_err(tas_priv->dev, "Unsupported dev %d\n", fw_hdr->device); + offset = -EINVAL; + goto out; + } + offset += 4; + fw_hdr->ndev = deviceNumber[fw_hdr->device]; + +out: + return offset; +} + +static int fw_parse_variable_header_git(struct tasdevice_priv + *tas_priv, const struct firmware *fmw, int offset) +{ + struct tasdevice_fw *tas_fmw = tas_priv->fmw; + struct tasdevice_dspfw_hdr *fw_hdr = &(tas_fmw->fw_hdr); + + offset = fw_parse_variable_hdr(tas_priv, fw_hdr, fmw, offset); + if (offset < 0) + goto out; + if (fw_hdr->ndev != tas_priv->ndev) { + dev_err(tas_priv->dev, + "%s: ndev(%u) in dspbin mismatch ndev(%u) in DTS\n", + __func__, fw_hdr->ndev, tas_priv->ndev); + offset = -EINVAL; + } + +out: + return offset; +} + +static int fw_parse_block_data(struct tasdevice_fw *tas_fmw, + struct tasdev_blk *block, const struct firmware *fmw, int offset) +{ + unsigned char *data = (unsigned char *)fmw->data; + int n; + + if (offset + 8 > fmw->size) { + dev_err(tas_fmw->dev, "%s: Type error\n", __func__); + offset = -EINVAL; + goto out; + } + block->type = be32_to_cpup((__be32 *)&data[offset]); + offset += 4; + + if (tas_fmw->fw_hdr.fixed_hdr.drv_ver >= PPC_DRIVER_CRCCHK) { + if (offset + 8 > fmw->size) { + dev_err(tas_fmw->dev, "PChkSumPresent error\n"); + offset = -EINVAL; + goto out; + } + block->is_pchksum_present = data[offset]; + offset++; + + block->pchksum = data[offset]; + offset++; + + block->is_ychksum_present = data[offset]; + offset++; + + block->ychksum = data[offset]; + offset++; + } else { + block->is_pchksum_present = 0; + block->is_ychksum_present = 0; + } + + block->nr_cmds = be32_to_cpup((__be32 *)&data[offset]); + offset += 4; + + n = block->nr_cmds * 4; + if (offset + n > fmw->size) { + dev_err(tas_fmw->dev, + "%s: File Size(%lu) error offset = %d n = %d\n", + __func__, (unsigned long)fmw->size, offset, n); + offset = -EINVAL; + goto out; + } + /* instead of kzalloc+memcpy */ + block->data = kmemdup(&data[offset], n, GFP_KERNEL); + if (!block->data) { + offset = -ENOMEM; + goto out; + } + offset += n; + +out: + return offset; +} + +/* When parsing error occurs, all the memory resource will be released + * in the end of tasdevice_rca_ready. + */ +static int fw_parse_data(struct tasdevice_fw *tas_fmw, + struct tasdevice_data *img_data, const struct firmware *fmw, + int offset) +{ + const unsigned char *data = (unsigned char *)fmw->data; + struct tasdev_blk *blk; + unsigned int i; + int n; + + if (offset + 64 > fmw->size) { + dev_err(tas_fmw->dev, "%s: Name error\n", __func__); + offset = -EINVAL; + goto out; + } + memcpy(img_data->name, &data[offset], 64); + offset += 64; + + n = strlen((char *)&data[offset]); + n++; + if (offset + n + 2 > fmw->size) { + dev_err(tas_fmw->dev, "%s: Description error\n", __func__); + offset = -EINVAL; + goto out; + } + offset += n; + img_data->nr_blk = be16_to_cpup((__be16 *)&data[offset]); + offset += 2; + + img_data->dev_blks = kcalloc(img_data->nr_blk, + sizeof(struct tasdev_blk), GFP_KERNEL); + if (!img_data->dev_blks) { + offset = -ENOMEM; + goto out; + } + for (i = 0; i < img_data->nr_blk; i++) { + blk = &(img_data->dev_blks[i]); + offset = fw_parse_block_data(tas_fmw, blk, fmw, offset); + if (offset < 0) { + offset = -EINVAL; + goto out; + } + } + +out: + return offset; +} + +/* When parsing error occurs, all the memory resource will be released + * in the end of tasdevice_rca_ready. + */ +static int fw_parse_program_data(struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, const struct firmware *fmw, int offset) +{ + unsigned char *buf = (unsigned char *)fmw->data; + struct tasdevice_prog *program; + int i; + + if (offset + 2 > fmw->size) { + dev_err(tas_priv->dev, "%s: File Size error\n", __func__); + offset = -EINVAL; + goto out; + } + tas_fmw->nr_programs = be16_to_cpup((__be16 *)&buf[offset]); + offset += 2; + + if (tas_fmw->nr_programs == 0) { + /*Not error in calibration Data file, return directly*/ + dev_info(tas_priv->dev, "%s: No Programs data, maybe calbin\n", + __func__); + goto out; + } + + tas_fmw->programs = + kcalloc(tas_fmw->nr_programs, sizeof(struct tasdevice_prog), + GFP_KERNEL); + if (!tas_fmw->programs) { + offset = -ENOMEM; + goto out; + } + for (i = 0; i < tas_fmw->nr_programs; i++) { + int n = 0; + + program = &(tas_fmw->programs[i]); + if (offset + 64 > fmw->size) { + dev_err(tas_priv->dev, "%s: mpName error\n", __func__); + offset = -EINVAL; + goto out; + } + offset += 64; + + n = strlen((char *)&buf[offset]); + /* skip '\0' and 5 unused bytes */ + n += 6; + if (offset + n > fmw->size) { + dev_err(tas_priv->dev, "Description err\n"); + offset = -EINVAL; + goto out; + } + + offset += n; + + offset = fw_parse_data(tas_fmw, &(program->dev_data), fmw, + offset); + if (offset < 0) + goto out; + } + +out: + return offset; +} + +/* When parsing error occurs, all the memory resource will be released + * in the end of tasdevice_rca_ready. + */ +static int fw_parse_configuration_data( + struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, + const struct firmware *fmw, int offset) +{ + unsigned char *data = (unsigned char *)fmw->data; + struct tasdevice_config *config; + unsigned int i; + int n; + + if (offset + 2 > fmw->size) { + dev_err(tas_priv->dev, "%s: File Size error\n", __func__); + offset = -EINVAL; + goto out; + } + tas_fmw->nr_configurations = be16_to_cpup((__be16 *)&data[offset]); + offset += 2; + + if (tas_fmw->nr_configurations == 0) { + dev_err(tas_priv->dev, "%s: Conf is zero\n", __func__); + /*Not error for calibration Data file, return directly*/ + goto out; + } + tas_fmw->configs = kcalloc(tas_fmw->nr_configurations, + sizeof(struct tasdevice_config), GFP_KERNEL); + if (!tas_fmw->configs) { + offset = -ENOMEM; + goto out; + } + for (i = 0; i < tas_fmw->nr_configurations; i++) { + config = &(tas_fmw->configs[i]); + if (offset + 64 > fmw->size) { + dev_err(tas_priv->dev, "File Size err\n"); + offset = -EINVAL; + goto out; + } + memcpy(config->name, &data[offset], 64); + offset += 64; + + n = strlen((char *)&data[offset]); + n += 15; + if (offset + n > fmw->size) { + dev_err(tas_priv->dev, "Description err\n"); + offset = -EINVAL; + goto out; + } + + offset += n; + + offset = fw_parse_data(tas_fmw, &(config->dev_data), + fmw, offset); + if (offset < 0) + goto out; + } + +out: + return offset; +} + +static bool check_inpage_yram_rg(struct tas_crc *cd, + unsigned char reg, unsigned char len) +{ + bool in = false; + + + if (reg <= TAS2781_YRAM5_END_REG && + reg >= TAS2781_YRAM5_START_REG) { + if (reg + len > TAS2781_YRAM5_END_REG) + cd->len = TAS2781_YRAM5_END_REG - reg + 1; + else + cd->len = len; + cd->offset = reg; + in = true; + } else if (reg < TAS2781_YRAM5_START_REG) { + if (reg + len > TAS2781_YRAM5_START_REG) { + cd->offset = TAS2781_YRAM5_START_REG; + cd->len = len - TAS2781_YRAM5_START_REG + reg; + in = true; + } + } + + return in; +} + +static bool check_inpage_yram_bk1(struct tas_crc *cd, + unsigned char page, unsigned char reg, unsigned char len) +{ + bool in = false; + + if (page == TAS2781_YRAM1_PAGE) { + if (reg >= TAS2781_YRAM1_START_REG) { + cd->offset = reg; + cd->len = len; + in = true; + } else if (reg + len > TAS2781_YRAM1_START_REG) { + cd->offset = TAS2781_YRAM1_START_REG; + cd->len = len - TAS2781_YRAM1_START_REG + reg; + in = true; + } + } else if (page == TAS2781_YRAM3_PAGE) + in = check_inpage_yram_rg(cd, reg, len); + + return in; +} + +/* Return Code: + * true -- the registers are in the inpage yram + * false -- the registers are NOT in the inpage yram + */ +static bool check_inpage_yram(struct tas_crc *cd, unsigned char book, + unsigned char page, unsigned char reg, unsigned char len) +{ + bool in = false; + + if (book == TAS2781_YRAM_BOOK1) { + in = check_inpage_yram_bk1(cd, page, reg, len); + goto end; + } + if (book == TAS2781_YRAM_BOOK2 && page == TAS2781_YRAM5_PAGE) + in = check_inpage_yram_rg(cd, reg, len); + +end: + return in; +} + +static bool check_inblock_yram_bk(struct tas_crc *cd, + unsigned char page, unsigned char reg, unsigned char len) +{ + bool in = false; + + if ((page >= TAS2781_YRAM4_START_PAGE && + page <= TAS2781_YRAM4_END_PAGE) || + (page >= TAS2781_YRAM2_START_PAGE && + page <= TAS2781_YRAM2_END_PAGE)) { + if (reg <= TAS2781_YRAM2_END_REG && + reg >= TAS2781_YRAM2_START_REG) { + cd->offset = reg; + cd->len = len; + in = true; + } else if (reg < TAS2781_YRAM2_START_REG) { + if (reg + len - 1 >= TAS2781_YRAM2_START_REG) { + cd->offset = TAS2781_YRAM2_START_REG; + cd->len = reg + len - TAS2781_YRAM2_START_REG; + in = true; + } + } + } + + return in; +} + +/* Return Code: + * true -- the registers are in the inblock yram + * false -- the registers are NOT in the inblock yram + */ +static bool check_inblock_yram(struct tas_crc *cd, unsigned char book, + unsigned char page, unsigned char reg, unsigned char len) +{ + bool in = false; + + if (book == TAS2781_YRAM_BOOK1 || book == TAS2781_YRAM_BOOK2) + in = check_inblock_yram_bk(cd, page, reg, len); + + return in; +} + +static bool check_yram(struct tas_crc *cd, unsigned char book, + unsigned char page, unsigned char reg, unsigned char len) +{ + bool in; + + in = check_inpage_yram(cd, book, page, reg, len); + if (in) + goto end; + in = check_inblock_yram(cd, book, page, reg, len); + +end: + return in; +} + +static int tasdev_multibytes_chksum(struct tasdevice_priv *tasdevice, + enum channel chn, unsigned char book, unsigned char page, + unsigned char reg, unsigned int len) +{ + struct tas_crc crc_data; + unsigned char crc_chksum = 0; + unsigned char nBuf1[128]; + int ret = 0; + int i; + bool in; + + if ((reg + len - 1) > 127) { + ret = -EINVAL; + dev_err(tasdevice->dev, "firmware error\n"); + goto end; + } + + if ((book == TASDEVICE_BOOK_ID(TAS2781_SA_COEFF_SWAP_REG)) + && (page == TASDEVICE_PAGE_ID(TAS2781_SA_COEFF_SWAP_REG)) + && (reg == TASDEVICE_PAGE_REG(TAS2781_SA_COEFF_SWAP_REG)) + && (len == 4)) { + /*DSP swap command, pass */ + ret = 0; + goto end; + } + + in = check_yram(&crc_data, book, page, reg, len); + if (!in) + goto end; + + if (len == 1) { + dev_err(tasdevice->dev, "firmware error\n"); + ret = -EINVAL; + goto end; + } + + ret = tasdevice_dev_bulk_read(tasdevice, chn, + TASDEVICE_REG(book, page, crc_data.offset), + nBuf1, crc_data.len); + if (ret < 0) + goto end; + + for (i = 0; i < crc_data.len; i++) { + if ((book == TASDEVICE_BOOK_ID(TAS2781_SA_COEFF_SWAP_REG)) + && (page == TASDEVICE_PAGE_ID( + TAS2781_SA_COEFF_SWAP_REG)) + && ((i + crc_data.offset) + >= TASDEVICE_PAGE_REG(TAS2781_SA_COEFF_SWAP_REG)) + && ((i + crc_data.offset) + <= (TASDEVICE_PAGE_REG(TAS2781_SA_COEFF_SWAP_REG) + + 4))) + /*DSP swap command, bypass */ + continue; + else + crc_chksum += crc8(tasdevice->crc8_lkp_tbl, &nBuf1[i], + 1, 0); + } + + ret = crc_chksum; + +end: + return ret; +} + +static int do_singlereg_checksum(struct tasdevice_priv *tasdevice, + enum channel chl, unsigned char book, unsigned char page, + unsigned char reg, unsigned char val) +{ + struct tas_crc crc_data; + unsigned int nData1; + int ret = 0; + bool in; + + if ((book == TASDEVICE_BOOK_ID(TAS2781_SA_COEFF_SWAP_REG)) + && (page == TASDEVICE_PAGE_ID(TAS2781_SA_COEFF_SWAP_REG)) + && (reg >= TASDEVICE_PAGE_REG(TAS2781_SA_COEFF_SWAP_REG)) + && (reg <= (TASDEVICE_PAGE_REG( + TAS2781_SA_COEFF_SWAP_REG) + 4))) { + /*DSP swap command, pass */ + ret = 0; + goto end; + } + + in = check_yram(&crc_data, book, page, reg, 1); + if (!in) + goto end; + ret = tasdevice_dev_read(tasdevice, chl, + TASDEVICE_REG(book, page, reg), &nData1); + if (ret < 0) + goto end; + + if (nData1 != val) { + dev_err(tasdevice->dev, + "B[0x%x]P[0x%x]R[0x%x] W[0x%x], R[0x%x]\n", + book, page, reg, val, nData1); + tasdevice->tasdevice[chl].err_code |= ERROR_YRAM_CRCCHK; + ret = -EAGAIN; + goto end; + } + + ret = crc8(tasdevice->crc8_lkp_tbl, &val, 1, 0); + +end: + return ret; +} + +static void set_err_prg_cfg(unsigned int type, struct tasdevice *dev) +{ + if ((type == MAIN_ALL_DEVICES) || (type == MAIN_DEVICE_A) + || (type == MAIN_DEVICE_B) || (type == MAIN_DEVICE_C) + || (type == MAIN_DEVICE_D)) + dev->cur_prog = -1; + else + dev->cur_conf = -1; +} + +static int tasdev_bytes_chksum(struct tasdevice_priv *tas_priv, + struct tasdev_blk *block, int chn, unsigned char book, + unsigned char page, unsigned char reg, unsigned int len, + unsigned char val, unsigned char *crc_chksum) +{ + int ret; + + if (len > 1) + ret = tasdev_multibytes_chksum(tas_priv, chn, book, page, reg, + len); + else + ret = do_singlereg_checksum(tas_priv, chn, book, page, reg, + val); + + if (ret > 0) { + *crc_chksum += (unsigned char)ret; + goto end; + } + + if (ret != -EAGAIN) + goto end; + + block->nr_retry--; + if (block->nr_retry > 0) + goto end; + + set_err_prg_cfg(block->type, &tas_priv->tasdevice[chn]); + +end: + return ret; +} + +static int tasdev_multibytes_wr(struct tasdevice_priv *tas_priv, + struct tasdev_blk *block, int chn, unsigned char book, + unsigned char page, unsigned char reg, unsigned char *data, + unsigned int len, unsigned int *nr_cmds, + unsigned char *crc_chksum) +{ + int ret; + + if (len > 1) { + ret = tasdevice_dev_bulk_write(tas_priv, chn, + TASDEVICE_REG(book, page, reg), data + 3, len); + if (ret < 0) + goto end; + if (block->is_ychksum_present) + ret = tasdev_bytes_chksum(tas_priv, block, chn, + book, page, reg, len, 0, crc_chksum); + } else { + ret = tasdevice_dev_write(tas_priv, chn, + TASDEVICE_REG(book, page, reg), data[3]); + if (ret < 0) + goto end; + if (block->is_ychksum_present) + ret = tasdev_bytes_chksum(tas_priv, block, chn, book, + page, reg, 1, data[3], crc_chksum); + } + + if (!block->is_ychksum_present || ret >= 0) { + *nr_cmds += 1; + if (len >= 2) + *nr_cmds += ((len - 2) / 4) + 1; + } + +end: + return ret; +} + +static int tasdev_block_chksum(struct tasdevice_priv *tas_priv, + struct tasdev_blk *block, int chn) +{ + unsigned int nr_value; + int ret; + + ret = tasdevice_dev_read(tas_priv, chn, TASDEVICE_I2CChecksum, + &nr_value); + if (ret < 0) { + dev_err(tas_priv->dev, "%s: Chn %d\n", __func__, chn); + set_err_prg_cfg(block->type, &tas_priv->tasdevice[chn]); + goto end; + } + + if ((nr_value & 0xff) != block->pchksum) { + dev_err(tas_priv->dev, "%s: Blk PChkSum Chn %d ", __func__, + chn); + dev_err(tas_priv->dev, "PChkSum = 0x%x, Reg = 0x%x\n", + block->pchksum, (nr_value & 0xff)); + tas_priv->tasdevice[chn].err_code |= ERROR_PRAM_CRCCHK; + ret = -EAGAIN; + block->nr_retry--; + + if (block->nr_retry <= 0) + set_err_prg_cfg(block->type, + &tas_priv->tasdevice[chn]); + } else + tas_priv->tasdevice[chn].err_code &= ~ERROR_PRAM_CRCCHK; + +end: + return ret; +} + +static int tasdev_load_blk(struct tasdevice_priv *tas_priv, + struct tasdev_blk *block, int chn) +{ + unsigned int sleep_time; + unsigned int len; + unsigned int nr_cmds; + unsigned char *data = block->data; + unsigned char crc_chksum = 0; + unsigned char offset; + unsigned char book; + unsigned char page; + unsigned char val; + int ret = 0; + + while (block->nr_retry > 0) { + if (block->is_pchksum_present) { + ret = tasdevice_dev_write(tas_priv, chn, + TASDEVICE_I2CChecksum, 0); + if (ret < 0) + break; + } + + if (block->is_ychksum_present) + crc_chksum = 0; + + nr_cmds = 0; + + while (nr_cmds < block->nr_cmds) { + data = block->data + nr_cmds * 4; + + book = data[0]; + page = data[1]; + offset = data[2]; + val = data[3]; + + nr_cmds++; + /*Single byte write*/ + if (offset <= 0x7F) { + ret = tasdevice_dev_write(tas_priv, chn, + TASDEVICE_REG(book, page, offset), + val); + if (ret < 0) + goto end; + if (block->is_ychksum_present) { + ret = tasdev_bytes_chksum(tas_priv, + block, chn, book, page, offset, + 1, val, &crc_chksum); + if (ret < 0) + break; + } + continue; + } + /*sleep command*/ + if (offset == 0x81) { + /*book -- data[0] page -- data[1]*/ + sleep_time = ((book << 8) + page)*1000; + usleep_range(sleep_time, sleep_time + 50); + continue; + } + /*Multiple bytes write*/ + if (offset == 0x85) { + data += 4; + len = (book << 8) + page; + book = data[0]; + page = data[1]; + offset = data[2]; + ret = tasdev_multibytes_wr(tas_priv, + block, chn, book, page, offset, data, + len, &nr_cmds, &crc_chksum); + if (ret < 0) + break; + } + } + if (ret == -EAGAIN) { + if (block->nr_retry > 0) + continue; + } else if (ret < 0) /*err in current device, skip it*/ + break; + + if (block->is_pchksum_present) { + ret = tasdev_block_chksum(tas_priv, block, chn); + if (ret == -EAGAIN) { + if (block->nr_retry > 0) + continue; + } else if (ret < 0) /*err in current device, skip it*/ + break; + } + + if (block->is_ychksum_present) { + /* TBD, open it when FW ready */ + dev_err(tas_priv->dev, + "Blk YChkSum: FW = 0x%x, YCRC = 0x%x\n", + block->ychksum, crc_chksum); + + tas_priv->tasdevice[chn].err_code &= + ~ERROR_YRAM_CRCCHK; + ret = 0; + } + /*skip current blk*/ + break; + } + +end: + return ret; +} + +static int tasdevice_load_block(struct tasdevice_priv *tas_priv, + struct tasdev_blk *block) +{ + int chnend = 0; + int ret = 0; + int chn = 0; + int rc = 0; + + switch (block->type) { + case MAIN_ALL_DEVICES: + chn = 0; + chnend = tas_priv->ndev; + break; + case MAIN_DEVICE_A: + case COEFF_DEVICE_A: + case PRE_DEVICE_A: + chn = 0; + chnend = 1; + break; + case MAIN_DEVICE_B: + case COEFF_DEVICE_B: + case PRE_DEVICE_B: + chn = 1; + chnend = 2; + break; + case MAIN_DEVICE_C: + case COEFF_DEVICE_C: + case PRE_DEVICE_C: + chn = 2; + chnend = 3; + break; + case MAIN_DEVICE_D: + case COEFF_DEVICE_D: + case PRE_DEVICE_D: + chn = 3; + chnend = 4; + break; + default: + dev_dbg(tas_priv->dev, "load blk: Other Type = 0x%02x\n", + block->type); + break; + } + + for (; chn < chnend; chn++) { + block->nr_retry = 6; + if (tas_priv->tasdevice[chn].is_loading == false) + continue; + ret = tasdev_load_blk(tas_priv, block, chn); + if (ret < 0) + dev_err(tas_priv->dev, "dev %d, Blk (%d) load error\n", + chn, block->type); + rc |= ret; + } + + return rc; +} + +static int dspfw_default_callback(struct tasdevice_priv *tas_priv, + unsigned int drv_ver, unsigned int ppcver) +{ + int rc = 0; + + if (drv_ver == 0x100) { + if (ppcver >= PPC3_VERSION) { + tas_priv->fw_parse_variable_header = + fw_parse_variable_header_kernel; + tas_priv->fw_parse_program_data = + fw_parse_program_data_kernel; + tas_priv->fw_parse_configuration_data = + fw_parse_configuration_data_kernel; + tas_priv->tasdevice_load_block = + tasdevice_load_block_kernel; + } else { + switch (ppcver) { + case 0x00: + tas_priv->fw_parse_variable_header = + fw_parse_variable_header_git; + tas_priv->fw_parse_program_data = + fw_parse_program_data; + tas_priv->fw_parse_configuration_data = + fw_parse_configuration_data; + tas_priv->tasdevice_load_block = + tasdevice_load_block; + break; + default: + dev_err(tas_priv->dev, + "%s: PPCVer must be 0x0 or 0x%02x", + __func__, PPC3_VERSION); + dev_err(tas_priv->dev, " Current:0x%02x\n", + ppcver); + rc = -EINVAL; + break; + } + } + } else { + dev_err(tas_priv->dev, + "DrvVer must be 0x0, 0x230 or above 0x230 "); + dev_err(tas_priv->dev, "current is 0x%02x\n", drv_ver); + rc = -EINVAL; + } + + return rc; +} + +static int load_calib_data(struct tasdevice_priv *tas_priv, + struct tasdevice_data *dev_data) +{ + struct tasdev_blk *block; + unsigned int i; + int ret = 0; + + for (i = 0; i < dev_data->nr_blk; i++) { + block = &(dev_data->dev_blks[i]); + ret = tasdevice_load_block(tas_priv, block); + if (ret < 0) + break; + } + + return ret; +} + +static int fw_parse_header(struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, const struct firmware *fmw, int offset) +{ + struct tasdevice_dspfw_hdr *fw_hdr = &(tas_fmw->fw_hdr); + struct tasdevice_fw_fixed_hdr *fw_fixed_hdr = &(fw_hdr->fixed_hdr); + const unsigned char magic_number[] = { 0x35, 0x35, 0x35, 0x32 }; + const unsigned char *buf = (unsigned char *)fmw->data; + + if (offset + 92 > fmw->size) { + dev_err(tas_priv->dev, "%s: File Size error\n", __func__); + offset = -EINVAL; + goto out; + } + if (memcmp(&buf[offset], magic_number, 4)) { + dev_err(tas_priv->dev, "%s: Magic num NOT match\n", __func__); + offset = -EINVAL; + goto out; + } + offset += 4; + + /* Convert data[offset], data[offset + 1], data[offset + 2] and + * data[offset + 3] into host + */ + fw_fixed_hdr->fwsize = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + if (fw_fixed_hdr->fwsize != fmw->size) { + dev_err(tas_priv->dev, "File size not match, %lu %u", + (unsigned long)fmw->size, fw_fixed_hdr->fwsize); + offset = -EINVAL; + goto out; + } + offset += 4; + fw_fixed_hdr->ppcver = be32_to_cpup((__be32 *)&buf[offset]); + offset += 8; + fw_fixed_hdr->drv_ver = be32_to_cpup((__be32 *)&buf[offset]); + offset += 72; + + out: + return offset; +} + +static int fw_parse_variable_hdr_cal(struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, const struct firmware *fmw, int offset) +{ + struct tasdevice_dspfw_hdr *fw_hdr = &(tas_fmw->fw_hdr); + + offset = fw_parse_variable_hdr(tas_priv, fw_hdr, fmw, offset); + if (offset < 0) + goto out; + if (fw_hdr->ndev != 1) { + dev_err(tas_priv->dev, + "%s: calbin must be 1, but currently ndev(%u)\n", + __func__, fw_hdr->ndev); + offset = -EINVAL; + } + +out: + return offset; +} + +/* When calibrated data parsing error occurs, DSP can still work with default + * calibrated data, memory resource related to calibrated data will be + * released in the tasdevice_codec_remove. + */ +static int fw_parse_calibration_data(struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, const struct firmware *fmw, int offset) +{ + struct tasdevice_calibration *calibration; + unsigned char *data = (unsigned char *)fmw->data; + unsigned int i, n; + + if (offset + 2 > fmw->size) { + dev_err(tas_priv->dev, "%s: Calibrations error\n", __func__); + offset = -EINVAL; + goto out; + } + tas_fmw->nr_calibrations = be16_to_cpup((__be16 *)&data[offset]); + offset += 2; + + if (tas_fmw->nr_calibrations != 1) { + dev_err(tas_priv->dev, + "%s: only support one calibraiton(%d)!\n", + __func__, tas_fmw->nr_calibrations); + goto out; + } + + tas_fmw->calibrations = kcalloc(tas_fmw->nr_calibrations, + sizeof(struct tasdevice_calibration), GFP_KERNEL); + if (!tas_fmw->calibrations) { + offset = -ENOMEM; + goto out; + } + for (i = 0; i < tas_fmw->nr_calibrations; i++) { + if (offset + 64 > fmw->size) { + dev_err(tas_priv->dev, "Calibrations error\n"); + offset = -EINVAL; + goto out; + } + calibration = &(tas_fmw->calibrations[i]); + offset += 64; + + n = strlen((char *)&data[offset]); + /* skip '\0' and 2 unused bytes */ + n += 3; + if (offset + n > fmw->size) { + dev_err(tas_priv->dev, "Description err\n"); + offset = -EINVAL; + goto out; + } + offset += n; + + offset = fw_parse_data(tas_fmw, &(calibration->dev_data), fmw, + offset); + if (offset < 0) + goto out; + } + +out: + return offset; +} + +int tas2781_load_calibration(void *context, char *file_name, + enum channel i) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)context; + struct tasdevice *tasdev = &(tas_priv->tasdevice[i]); + const struct firmware *fw_entry; + struct tasdevice_fw *tas_fmw; + struct firmware fmw; + int offset = 0; + int ret; + + ret = request_firmware(&fw_entry, file_name, tas_priv->dev); + if (ret) { + dev_info(tas_priv->dev, "%s: Request firmware %s failed\n", + __func__, file_name); + goto out; + } + + if (!fw_entry->size) { + dev_err(tas_priv->dev, "%s: file read error: size = %lu\n", + __func__, (unsigned long)fw_entry->size); + goto out; + } + fmw.size = fw_entry->size; + fmw.data = fw_entry->data; + + tas_fmw = tasdev->cali_data_fmw = kzalloc(sizeof(struct tasdevice_fw), + GFP_KERNEL); + if (!tasdev->cali_data_fmw) { + ret = -ENOMEM; + goto out; + } + tas_fmw->dev = tas_priv->dev; + offset = fw_parse_header(tas_priv, tas_fmw, &fmw, offset); + if (offset == -EINVAL) { + dev_err(tas_priv->dev, "fw_parse_header EXIT!\n"); + ret = offset; + goto out; + } + offset = fw_parse_variable_hdr_cal(tas_priv, tas_fmw, &fmw, offset); + if (offset == -EINVAL) { + dev_err(tas_priv->dev, + "%s: fw_parse_variable_header_cal EXIT!\n", __func__); + ret = offset; + goto out; + } + offset = fw_parse_program_data(tas_priv, tas_fmw, &fmw, offset); + if (offset < 0) { + dev_err(tas_priv->dev, "fw_parse_program_data EXIT!\n"); + ret = offset; + goto out; + } + offset = fw_parse_configuration_data(tas_priv, tas_fmw, &fmw, offset); + if (offset < 0) { + dev_err(tas_priv->dev, "fw_parse_configuration_data EXIT!\n"); + ret = offset; + goto out; + } + offset = fw_parse_calibration_data(tas_priv, tas_fmw, &fmw, offset); + if (offset < 0) { + dev_err(tas_priv->dev, "fw_parse_calibration_data EXIT!\n"); + ret = offset; + goto out; + } + +out: + if (fw_entry) + release_firmware(fw_entry); + + return ret; +} +EXPORT_SYMBOL_NS_GPL(tas2781_load_calibration, SND_SOC_TAS2781_FMWLIB); + +static int tasdevice_dspfw_ready(const struct firmware *fmw, + void *context) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + struct tasdevice_fw_fixed_hdr *fw_fixed_hdr; + struct tasdevice_fw *tas_fmw; + int offset = 0; + int ret = 0; + + if (!fmw || !fmw->data) { + dev_err(tas_priv->dev, "%s: Failed to read firmware %s\n", + __func__, tas_priv->coef_binaryname); + ret = -EINVAL; + goto out; + } + + tas_priv->fmw = kzalloc(sizeof(struct tasdevice_fw), GFP_KERNEL); + if (!tas_priv->fmw) { + ret = -ENOMEM; + goto out; + } + tas_fmw = tas_priv->fmw; + tas_fmw->dev = tas_priv->dev; + offset = fw_parse_header(tas_priv, tas_fmw, fmw, offset); + + if (offset == -EINVAL) { + ret = -EINVAL; + goto out; + } + fw_fixed_hdr = &(tas_fmw->fw_hdr.fixed_hdr); + /* Support different versions of firmware */ + switch (fw_fixed_hdr->drv_ver) { + case 0x301: + case 0x302: + case 0x502: + tas_priv->fw_parse_variable_header = + fw_parse_variable_header_kernel; + tas_priv->fw_parse_program_data = + fw_parse_program_data_kernel; + tas_priv->fw_parse_configuration_data = + fw_parse_configuration_data_kernel; + tas_priv->tasdevice_load_block = + tasdevice_load_block_kernel; + break; + case 0x202: + case 0x400: + tas_priv->fw_parse_variable_header = + fw_parse_variable_header_git; + tas_priv->fw_parse_program_data = + fw_parse_program_data; + tas_priv->fw_parse_configuration_data = + fw_parse_configuration_data; + tas_priv->tasdevice_load_block = + tasdevice_load_block; + break; + default: + ret = dspfw_default_callback(tas_priv, + fw_fixed_hdr->drv_ver, fw_fixed_hdr->ppcver); + if (ret) + goto out; + break; + } + + offset = tas_priv->fw_parse_variable_header(tas_priv, fmw, offset); + if (offset < 0) { + ret = offset; + goto out; + } + offset = tas_priv->fw_parse_program_data(tas_priv, tas_fmw, fmw, + offset); + if (offset < 0) { + ret = offset; + goto out; + } + offset = tas_priv->fw_parse_configuration_data(tas_priv, + tas_fmw, fmw, offset); + if (offset < 0) + ret = offset; + +out: + return ret; +} + +int tasdevice_dsp_parser(void *context) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)context; + const struct firmware *fw_entry; + int ret; + + ret = request_firmware(&fw_entry, tas_priv->coef_binaryname, + tas_priv->dev); + if (ret) { + dev_err(tas_priv->dev, "%s: load %s error\n", __func__, + tas_priv->coef_binaryname); + goto out; + } + + ret = tasdevice_dspfw_ready(fw_entry, tas_priv); + release_firmware(fw_entry); + fw_entry = NULL; + +out: + return ret; +} +EXPORT_SYMBOL_NS_GPL(tasdevice_dsp_parser, SND_SOC_TAS2781_FMWLIB); + +static void tas2781_clear_calfirmware(struct tasdevice_fw *tas_fmw) +{ + struct tasdevice_calibration *calibration; + struct tasdev_blk *block; + struct tasdevice_data *im; + unsigned int blks; + int i; + + if (!tas_fmw->calibrations) + goto out; + + for (i = 0; i < tas_fmw->nr_calibrations; i++) { + calibration = &(tas_fmw->calibrations[i]); + if (!calibration) + continue; + + im = &(calibration->dev_data); + + if (!im->dev_blks) + continue; + + for (blks = 0; blks < im->nr_blk; blks++) { + block = &(im->dev_blks[blks]); + if (!block) + continue; + kfree(block->data); + } + kfree(im->dev_blks); + } + kfree(tas_fmw->calibrations); +out: + kfree(tas_fmw); +} + +void tasdevice_calbin_remove(void *context) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + struct tasdevice *tasdev; + int i; + + if (!tas_priv) + return; + + for (i = 0; i < tas_priv->ndev; i++) { + tasdev = &(tas_priv->tasdevice[i]); + if (!tasdev->cali_data_fmw) + continue; + tas2781_clear_calfirmware(tasdev->cali_data_fmw); + tasdev->cali_data_fmw = NULL; + } +} +EXPORT_SYMBOL_NS_GPL(tasdevice_calbin_remove, SND_SOC_TAS2781_FMWLIB); + +void tasdevice_config_info_remove(void *context) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + struct tasdevice_rca *rca = &(tas_priv->rcabin); + struct tasdevice_config_info **ci = rca->cfg_info; + int i, j; + + if (!ci) + return; + for (i = 0; i < rca->ncfgs; i++) { + if (!ci[i]) + continue; + if (ci[i]->blk_data) { + for (j = 0; j < (int)ci[i]->real_nblocks; j++) { + if (!ci[i]->blk_data[j]) + continue; + kfree(ci[i]->blk_data[j]->regdata); + kfree(ci[i]->blk_data[j]); + } + kfree(ci[i]->blk_data); + } + kfree(ci[i]); + } + kfree(ci); +} +EXPORT_SYMBOL_NS_GPL(tasdevice_config_info_remove, SND_SOC_TAS2781_FMWLIB); + +static int tasdevice_load_data(struct tasdevice_priv *tas_priv, + struct tasdevice_data *dev_data) +{ + struct tasdev_blk *block; + unsigned int i; + int ret = 0; + + for (i = 0; i < dev_data->nr_blk; i++) { + block = &(dev_data->dev_blks[i]); + ret = tas_priv->tasdevice_load_block(tas_priv, block); + if (ret < 0) + break; + } + + return ret; +} + +int tasdevice_select_tuningprm_cfg(void *context, int prm_no, + int cfg_no, int rca_conf_no) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + struct tasdevice_rca *rca = &(tas_priv->rcabin); + struct tasdevice_config_info **cfg_info = rca->cfg_info; + struct tasdevice_fw *tas_fmw = tas_priv->fmw; + struct tasdevice_prog *program; + struct tasdevice_config *conf; + int prog_status = 0; + int status, i; + + if (!tas_fmw) { + dev_err(tas_priv->dev, "%s: Firmware is NULL\n", __func__); + goto out; + } + + if (cfg_no >= tas_fmw->nr_configurations) { + dev_err(tas_priv->dev, + "%s: cfg(%d) is not in range of conf %u\n", + __func__, cfg_no, tas_fmw->nr_configurations); + goto out; + } + + if (prm_no >= tas_fmw->nr_programs) { + dev_err(tas_priv->dev, + "%s: prm(%d) is not in range of Programs %u\n", + __func__, prm_no, tas_fmw->nr_programs); + goto out; + } + + if (rca_conf_no > rca->ncfgs || rca_conf_no <= 0 || + !cfg_info) { + dev_err(tas_priv->dev, + "conf_no:%d should be in range from 0 to %u\n", + rca_conf_no, rca->ncfgs-1); + goto out; + } + + conf = &(tas_fmw->configs[cfg_no]); + for (i = 0, prog_status = 0; i < tas_priv->ndev; i++) { + if (cfg_info[rca_conf_no]->active_dev & (1 << i)) { + if (tas_priv->tasdevice[i].cur_prog != prm_no) { + tas_priv->tasdevice[i].cur_conf = -1; + tas_priv->tasdevice[i].is_loading = true; + prog_status++; + } + } else + tas_priv->tasdevice[i].is_loading = false; + tas_priv->tasdevice[i].is_loaderr = false; + } + + if (prog_status) { + program = &(tas_fmw->programs[prm_no]); + tasdevice_load_data(tas_priv, &(program->dev_data)); + for (i = 0; i < tas_priv->ndev; i++) { + if (tas_priv->tasdevice[i].is_loaderr == true) + continue; + else if (tas_priv->tasdevice[i].is_loaderr == false + && tas_priv->tasdevice[i].is_loading == true) { + struct tasdevice_fw *cal_fmw = + tas_priv->tasdevice[i].cali_data_fmw; + + if (cal_fmw) { + struct tasdevice_calibration + *cal = cal_fmw->calibrations; + + if (cal) + load_calib_data(tas_priv, + &(cal->dev_data)); + } + tas_priv->tasdevice[i].cur_prog = prm_no; + } + } + } + + for (i = 0, status = 0; i < tas_priv->ndev; i++) { + if (tas_priv->tasdevice[i].cur_conf != cfg_no + && (cfg_info[rca_conf_no]->active_dev & (1 << i)) + && (tas_priv->tasdevice[i].is_loaderr == false)) { + status++; + tas_priv->tasdevice[i].is_loading = true; + } else + tas_priv->tasdevice[i].is_loading = false; + } + + if (status) { + status = 0; + tasdevice_load_data(tas_priv, &(conf->dev_data)); + for (i = 0; i < tas_priv->ndev; i++) { + if (tas_priv->tasdevice[i].is_loaderr == true) { + status |= 1 << (i + 4); + continue; + } else if (tas_priv->tasdevice[i].is_loaderr == false + && tas_priv->tasdevice[i].is_loading == true) + tas_priv->tasdevice[i].cur_conf = cfg_no; + } + } else + dev_err(tas_priv->dev, + "%s: No device is in active in conf %d\n", + __func__, rca_conf_no); + + status |= cfg_info[rca_conf_no]->active_dev; + +out: + return prog_status; +} +EXPORT_SYMBOL_NS_GPL(tasdevice_select_tuningprm_cfg, + SND_SOC_TAS2781_FMWLIB); + +int tasdevice_prmg_load(void *context, int prm_no) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + struct tasdevice_fw *tas_fmw = tas_priv->fmw; + struct tasdevice_prog *program; + int prog_status = 0; + int i; + + if (!tas_fmw) { + dev_err(tas_priv->dev, "%s: Firmware is NULL\n", __func__); + goto out; + } + + if (prm_no >= tas_fmw->nr_programs) { + dev_err(tas_priv->dev, + "%s: prm(%d) is not in range of Programs %u\n", + __func__, prm_no, tas_fmw->nr_programs); + goto out; + } + + for (i = 0, prog_status = 0; i < tas_priv->ndev; i++) { + if (tas_priv->tasdevice[i].cur_prog != prm_no) { + tas_priv->tasdevice[i].cur_conf = -1; + tas_priv->tasdevice[i].is_loading = true; + prog_status++; + } + } + + if (prog_status) { + program = &(tas_fmw->programs[prm_no]); + tasdevice_load_data(tas_priv, &(program->dev_data)); + for (i = 0; i < tas_priv->ndev; i++) { + if (tas_priv->tasdevice[i].is_loaderr == true) + continue; + else if (tas_priv->tasdevice[i].is_loaderr == false + && tas_priv->tasdevice[i].is_loading == true) + tas_priv->tasdevice[i].cur_prog = prm_no; + } + } + if (tas_priv->set_global_mode) + tas_priv->set_global_mode(tas_priv); +out: + return prog_status; +} +EXPORT_SYMBOL_NS_GPL(tasdevice_prmg_load, SND_SOC_TAS2781_FMWLIB); + +int tasdevice_prmg_calibdata_load(void *context, int prm_no) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + struct tasdevice_fw *tas_fmw = tas_priv->fmw; + struct tasdevice_prog *program; + int prog_status = 0; + int i; + + if (!tas_fmw) { + dev_err(tas_priv->dev, "%s: Firmware is NULL\n", __func__); + goto out; + } + + if (prm_no >= tas_fmw->nr_programs) { + dev_err(tas_priv->dev, + "%s: prm(%d) is not in range of Programs %u\n", + __func__, prm_no, tas_fmw->nr_programs); + goto out; + } + + for (i = 0, prog_status = 0; i < tas_priv->ndev; i++) { + if (tas_priv->tasdevice[i].cur_prog != prm_no) { + tas_priv->tasdevice[i].cur_conf = -1; + tas_priv->tasdevice[i].is_loading = true; + prog_status++; + } + tas_priv->tasdevice[i].is_loaderr = false; + } + + if (prog_status) { + program = &(tas_fmw->programs[prm_no]); + tasdevice_load_data(tas_priv, &(program->dev_data)); + for (i = 0; i < tas_priv->ndev; i++) { + if (tas_priv->tasdevice[i].is_loaderr == true) + continue; + else if (tas_priv->tasdevice[i].is_loaderr == false + && tas_priv->tasdevice[i].is_loading == true) { + struct tasdevice_fw *cal_fmw = + tas_priv->tasdevice[i].cali_data_fmw; + + if (cal_fmw) { + struct tasdevice_calibration *cal = + cal_fmw->calibrations; + + if (cal) + load_calib_data(tas_priv, + &(cal->dev_data)); + } + tas_priv->tasdevice[i].cur_prog = prm_no; + } + } + } + +out: + return prog_status; +} +EXPORT_SYMBOL_NS_GPL(tasdevice_prmg_calibdata_load, + SND_SOC_TAS2781_FMWLIB); + +void tasdevice_tuning_switch(void *context, int state) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + struct tasdevice_fw *tas_fmw = tas_priv->fmw; + int profile_cfg_id = 0; + + if (tas_priv->fw_state == TASDEVICE_DSP_FW_FAIL) { + dev_err(tas_priv->dev, "DSP bin file not loaded\n"); + return; + } + + if (state == 0) { + if (tas_priv->cur_prog >= tas_fmw->nr_programs) + /*bypass all in rca is profile id 0*/ + profile_cfg_id = RCA_CONFIGID_BYPASS_ALL; + else { + /*dsp mode or tuning mode*/ + profile_cfg_id = tas_priv->rcabin.profile_cfg_id; + tasdevice_select_tuningprm_cfg(tas_priv, + tas_priv->cur_prog, tas_priv->cur_conf, + profile_cfg_id); + if (tas_priv->set_global_mode) + tas_priv->set_global_mode(tas_priv); + } + + tasdevice_select_cfg_blk(tas_priv, profile_cfg_id, + TASDEVICE_BIN_BLK_PRE_POWER_UP); + } else + tasdevice_select_cfg_blk(tas_priv, + tas_priv->rcabin.profile_cfg_id, + TASDEVICE_BIN_BLK_PRE_SHUTDOWN); +} +EXPORT_SYMBOL_NS_GPL(tasdevice_tuning_switch, + SND_SOC_TAS2781_FMWLIB); + +MODULE_DESCRIPTION("Texas Firmware Support"); +MODULE_AUTHOR("Shenghao Ding, TI, <shenghao-ding(a)ti.com>"); +MODULE_LICENSE("GPL"); -- 2.34.1

1 0

Patch for HP Spectre x360 Convertible 14t-ea100 Sound (patch_realtek.c)
by Dave Greengas 08 May '23

08 May '23

The sound for this laptop does not work without a patch to patch_realtek.c. I noticed that it has an ALC245 sound card, but a different product id. I have been running this patch for months and it works well. There is the known issue with the top-mounted speakers, but this is the same as when I manually run the hda-verbs as described on a forum post on kernel.org for similar models. I added the following line: SND_PCI_QUIRK(0x103c, 0x89da, "HP Spectre x360 14", ALC245_FIXUP_HP_X360_AMP), Only the model 0x89da is different. I ran the diff command against a 62 kernel, but noticed that 63 has the same file and showed no commits. I have been running this patch successfully for many months on the 62 branch, but I do not know anyone else with this same laptop model to confirm that it works for them. If there is a different process for submitting the patch, please let me know. Kernel 63 was just released for my distribution and I plan to test the patch there as well, but I do not expect it to work differently. --------------------------------- David Greengas

1 0

Bug: premature stringification in SND_DLSYM_BUILD_VERSION produces wrong results for alsa-plugins.
by GitHub issues - edited 07 May '23

07 May '23

alsa-project/alsa-lib issue #316 was edited from MIvanchev: [The macro](https://github.com/alsa-project/alsa-lib/blob/master/include/global.…: ``` #define SND_DLSYM_BUILD_VERSION(name, version) \ static struct snd_dlsym_link __SND_DLSYM_VERSION(snd_dlsym_, name, version); \ void __SND_DLSYM_VERSION(snd_dlsym_constructor_, name, version) (void) __attribute__ ((constructor)); \ void __SND_DLSYM_VERSION(snd_dlsym_constructor_, name, version) (void) { \ __SND_DLSYM_VERSION(snd_dlsym_, name, version).next = snd_dlsym_start; \ __SND_DLSYM_VERSION(snd_dlsym_, name, version).dlsym_name = # name; \ __SND_DLSYM_VERSION(snd_dlsym_, name, version).dlsym_ptr = (void *)&name; \ snd_dlsym_start = &__SND_DLSYM_VERSION(snd_dlsym_, name, version); \ } ``` should actually be ``` #define SND_DLSYM_NAME(name) #name #define SND_DLSYM_BUILD_VERSION(name, version) \ static struct snd_dlsym_link __SND_DLSYM_VERSION(snd_dlsym_, name, version); \ void __SND_DLSYM_VERSION(snd_dlsym_constructor_, name, version) (void) __attribute__ ((constructor)); \ void __SND_DLSYM_VERSION(snd_dlsym_constructor_, name, version) (void) { \ __SND_DLSYM_VERSION(snd_dlsym_, name, version).next = snd_dlsym_start; \ __SND_DLSYM_VERSION(snd_dlsym_, name, version).dlsym_name = SND_DLSYM_NAME(name) \ __SND_DLSYM_VERSION(snd_dlsym_, name, version).dlsym_ptr = (void *)&name; \ snd_dlsym_start = &__SND_DLSYM_VERSION(snd_dlsym_, name, version); \ } ``` This is because for instance [this code](https://github.com/alsa-project/alsa-plugins/blob/master/pulse/ctl_pu… `SND_CTL_PLUGIN_SYMBOL(pulse);` expands to ``` SND_DLSYM_BUILD_VERSION(SND_CTL_PLUGIN_ENTRY(pulse), SND_CONTROL_DLSYM_VERSION); ``` and this expands to ``` ... __SND_DLSYM_VERSION(snd_dlsym_, name, version).dlsym_name = # SND_CTL_PLUGIN_ENTRY(pulse) ... ``` but the C preprocessor doesn't expand stringified tokens so the value of `dlsym_name` is actually `"SND_CTL_PLUGIN_ENTRY(pulse)"`. Issue URL : https://github.com/alsa-project/alsa-lib/issues/316 Repository URL: https://github.com/alsa-project/alsa-lib

1 0

Bug: premature stringification in SND_DLSYM_BUILD_VERSION produces wrong results for alsa-plugins.
by GitHub issues - opened 07 May '23

07 May '23

alsa-project/alsa-lib issue #316 was opened from MIvanchev: The macro: ``` #define SND_DLSYM_BUILD_VERSION(name, version) \ static struct snd_dlsym_link __SND_DLSYM_VERSION(snd_dlsym_, name, version); \ void __SND_DLSYM_VERSION(snd_dlsym_constructor_, name, version) (void) __attribute__ ((constructor)); \ void __SND_DLSYM_VERSION(snd_dlsym_constructor_, name, version) (void) { \ __SND_DLSYM_VERSION(snd_dlsym_, name, version).next = snd_dlsym_start; \ __SND_DLSYM_VERSION(snd_dlsym_, name, version).dlsym_name = # name; \ __SND_DLSYM_VERSION(snd_dlsym_, name, version).dlsym_ptr = (void *)&name; \ snd_dlsym_start = &__SND_DLSYM_VERSION(snd_dlsym_, name, version); \ } ``` should actually be ``` #define SND_DLSYM_NAME(name) #name #define SND_DLSYM_BUILD_VERSION(name, version) \ static struct snd_dlsym_link __SND_DLSYM_VERSION(snd_dlsym_, name, version); \ void __SND_DLSYM_VERSION(snd_dlsym_constructor_, name, version) (void) __attribute__ ((constructor)); \ void __SND_DLSYM_VERSION(snd_dlsym_constructor_, name, version) (void) { \ __SND_DLSYM_VERSION(snd_dlsym_, name, version).next = snd_dlsym_start; \ __SND_DLSYM_VERSION(snd_dlsym_, name, version).dlsym_name = SND_DLSYM_NAME(name) \ __SND_DLSYM_VERSION(snd_dlsym_, name, version).dlsym_ptr = (void *)&name; \ snd_dlsym_start = &__SND_DLSYM_VERSION(snd_dlsym_, name, version); \ } ``` This is because for instance [this code](https://github.com/alsa-project/alsa-plugins/blob/master/pulse/ctl_pu… `SND_CTL_PLUGIN_SYMBOL(pulse);` expands to ``` SND_DLSYM_BUILD_VERSION(SND_CTL_PLUGIN_ENTRY(pulse), SND_CONTROL_DLSYM_VERSION); ``` and this expands to ``` ... __SND_DLSYM_VERSION(snd_dlsym_, name, version).dlsym_name = # SND_CTL_PLUGIN_ENTRY(pulse) ... ``` but the C preprocessor doesn't expand stringified tokens so the value of `dlsym_name` is actually `"SND_CTL_PLUGIN_ENTRY(pulse)"`. Issue URL : https://github.com/alsa-project/alsa-lib/issues/316 Repository URL: https://github.com/alsa-project/alsa-lib

1 0

[PATCH AUTOSEL 4.14 1/8] ASoC: jack: allow multiple interrupt per gpio
by Sasha Levin 07 May '23

07 May '23

From: Svyatoslav Ryhel <clamor95(a)gmail.com> [ Upstream commit a2d4051b0bd6dffcd736888ae89a550d6f60b060 ] This feature is required for coupled hp-mic quirk used by some Nvidia Tegra 3 based devices work properly. Signed-off-by: Svyatoslav Ryhel <clamor95(a)gmail.com> Link: https://lore.kernel.org/r/20230221183211.21964-3-clamor95@gmail.com Signed-off-by: Mark Brown <broonie(a)kernel.org> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- sound/soc/soc-jack.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/soc/soc-jack.c b/sound/soc/soc-jack.c index b04ecc633da36..f04a6eb8eecc8 100644 --- a/sound/soc/soc-jack.c +++ b/sound/soc/soc-jack.c @@ -451,6 +451,7 @@ int snd_soc_jack_add_gpios(struct snd_soc_jack *jack, int count, ret = request_any_context_irq(gpiod_to_irq(gpios[i].desc), gpio_handler, + IRQF_SHARED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, gpios[i].name, -- 2.39.2

1 0

[PATCH AUTOSEL 4.19 1/9] ASoC: jack: allow multiple interrupt per gpio
by Sasha Levin 07 May '23

07 May '23

From: Svyatoslav Ryhel <clamor95(a)gmail.com> [ Upstream commit a2d4051b0bd6dffcd736888ae89a550d6f60b060 ] This feature is required for coupled hp-mic quirk used by some Nvidia Tegra 3 based devices work properly. Signed-off-by: Svyatoslav Ryhel <clamor95(a)gmail.com> Link: https://lore.kernel.org/r/20230221183211.21964-3-clamor95@gmail.com Signed-off-by: Mark Brown <broonie(a)kernel.org> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- sound/soc/soc-jack.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/soc/soc-jack.c b/sound/soc/soc-jack.c index 2a528e73bad25..bba84df0982f7 100644 --- a/sound/soc/soc-jack.c +++ b/sound/soc/soc-jack.c @@ -424,6 +424,7 @@ int snd_soc_jack_add_gpios(struct snd_soc_jack *jack, int count, ret = request_any_context_irq(gpiod_to_irq(gpios[i].desc), gpio_handler, + IRQF_SHARED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, gpios[i].name, -- 2.39.2

1 0

[PATCH AUTOSEL 5.4 1/9] ASoC: jack: allow multiple interrupt per gpio
by Sasha Levin 07 May '23

07 May '23

From: Svyatoslav Ryhel <clamor95(a)gmail.com> [ Upstream commit a2d4051b0bd6dffcd736888ae89a550d6f60b060 ] This feature is required for coupled hp-mic quirk used by some Nvidia Tegra 3 based devices work properly. Signed-off-by: Svyatoslav Ryhel <clamor95(a)gmail.com> Link: https://lore.kernel.org/r/20230221183211.21964-3-clamor95@gmail.com Signed-off-by: Mark Brown <broonie(a)kernel.org> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- sound/soc/soc-jack.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/soc/soc-jack.c b/sound/soc/soc-jack.c index b5748dcd490f2..e83f9a2541cab 100644 --- a/sound/soc/soc-jack.c +++ b/sound/soc/soc-jack.c @@ -406,6 +406,7 @@ int snd_soc_jack_add_gpios(struct snd_soc_jack *jack, int count, ret = request_any_context_irq(gpiod_to_irq(gpios[i].desc), gpio_handler, + IRQF_SHARED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, gpios[i].name, -- 2.39.2

1 0

[PATCH AUTOSEL 5.10 1/9] ASoC: jack: allow multiple interrupt per gpio
by Sasha Levin 07 May '23

07 May '23

From: Svyatoslav Ryhel <clamor95(a)gmail.com> [ Upstream commit a2d4051b0bd6dffcd736888ae89a550d6f60b060 ] This feature is required for coupled hp-mic quirk used by some Nvidia Tegra 3 based devices work properly. Signed-off-by: Svyatoslav Ryhel <clamor95(a)gmail.com> Link: https://lore.kernel.org/r/20230221183211.21964-3-clamor95@gmail.com Signed-off-by: Mark Brown <broonie(a)kernel.org> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- sound/soc/soc-jack.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/soc/soc-jack.c b/sound/soc/soc-jack.c index 0f1820f36b4d7..80ea4408e6ad6 100644 --- a/sound/soc/soc-jack.c +++ b/sound/soc/soc-jack.c @@ -368,6 +368,7 @@ int snd_soc_jack_add_gpios(struct snd_soc_jack *jack, int count, ret = request_any_context_irq(gpiod_to_irq(gpios[i].desc), gpio_handler, + IRQF_SHARED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, gpios[i].name, -- 2.39.2

1 0

[PATCH AUTOSEL 5.15 01/10] ASoC: jack: allow multiple interrupt per gpio
by Sasha Levin 07 May '23

07 May '23

From: Svyatoslav Ryhel <clamor95(a)gmail.com> [ Upstream commit a2d4051b0bd6dffcd736888ae89a550d6f60b060 ] This feature is required for coupled hp-mic quirk used by some Nvidia Tegra 3 based devices work properly. Signed-off-by: Svyatoslav Ryhel <clamor95(a)gmail.com> Link: https://lore.kernel.org/r/20230221183211.21964-3-clamor95@gmail.com Signed-off-by: Mark Brown <broonie(a)kernel.org> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- sound/soc/soc-jack.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/soc/soc-jack.c b/sound/soc/soc-jack.c index d798765d168c4..a7256ad49b243 100644 --- a/sound/soc/soc-jack.c +++ b/sound/soc/soc-jack.c @@ -367,6 +367,7 @@ int snd_soc_jack_add_gpios(struct snd_soc_jack *jack, int count, ret = request_any_context_irq(gpiod_to_irq(gpios[i].desc), gpio_handler, + IRQF_SHARED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, gpios[i].name, -- 2.39.2

1 1

[PATCH AUTOSEL 6.1 01/19] ASoC: jack: allow multiple interrupt per gpio
by Sasha Levin 07 May '23

07 May '23

From: Svyatoslav Ryhel <clamor95(a)gmail.com> [ Upstream commit a2d4051b0bd6dffcd736888ae89a550d6f60b060 ] This feature is required for coupled hp-mic quirk used by some Nvidia Tegra 3 based devices work properly. Signed-off-by: Svyatoslav Ryhel <clamor95(a)gmail.com> Link: https://lore.kernel.org/r/20230221183211.21964-3-clamor95@gmail.com Signed-off-by: Mark Brown <broonie(a)kernel.org> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- sound/soc/soc-jack.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/soc/soc-jack.c b/sound/soc/soc-jack.c index fcece5ca38c69..f951acb2ce362 100644 --- a/sound/soc/soc-jack.c +++ b/sound/soc/soc-jack.c @@ -367,6 +367,7 @@ int snd_soc_jack_add_gpios(struct snd_soc_jack *jack, int count, ret = request_any_context_irq(gpiod_to_irq(gpios[i].desc), gpio_handler, + IRQF_SHARED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, gpios[i].name, -- 2.39.2

1 5

[PATCH AUTOSEL 6.2 01/20] ASoC: jack: allow multiple interrupt per gpio
by Sasha Levin 07 May '23

07 May '23

From: Svyatoslav Ryhel <clamor95(a)gmail.com> [ Upstream commit a2d4051b0bd6dffcd736888ae89a550d6f60b060 ] This feature is required for coupled hp-mic quirk used by some Nvidia Tegra 3 based devices work properly. Signed-off-by: Svyatoslav Ryhel <clamor95(a)gmail.com> Link: https://lore.kernel.org/r/20230221183211.21964-3-clamor95@gmail.com Signed-off-by: Mark Brown <broonie(a)kernel.org> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- sound/soc/soc-jack.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/soc/soc-jack.c b/sound/soc/soc-jack.c index fcece5ca38c69..f951acb2ce362 100644 --- a/sound/soc/soc-jack.c +++ b/sound/soc/soc-jack.c @@ -367,6 +367,7 @@ int snd_soc_jack_add_gpios(struct snd_soc_jack *jack, int count, ret = request_any_context_irq(gpiod_to_irq(gpios[i].desc), gpio_handler, + IRQF_SHARED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, gpios[i].name, -- 2.39.2

1 5

MSI MAG B650M Mortar Wifi Spdif input & output are reversed
by GitHub issues - opened 06 May '23

06 May '23

alsa-project/alsa-ucm-conf issue #311 was opened from RenEH01: Hi, I have a MSI MAG B650M Mortar Wifi. I have installed this UCM conf files which provided no sound. I further installed pauvcontrol and I found changing the USB Audio device under Configuration to Pro Audio and changing the output device under Output Devices to USB Audio Pro 2 allowed for sound. When I select Digital Stereo (IEC958) Output under configuration I get no sound. When I select Digital Stereo Duplex Duplex under configuration I get no sound, but there is sound under Input Devices. I believe this is reversed. I do not think this board has spdif input functionality at all. A side effect of using Pro Audio 2 for output is that none of my multi channel tracks are downsampled for 2.0. I'm guessing this will be resolved if the above isssue is resolved. Would that be correct? Issue URL : https://github.com/alsa-project/alsa-ucm-conf/issues/311 Repository URL: https://github.com/alsa-project/alsa-ucm-conf

1 0

Some USB-Audio speakers with non-existent S/PDIF outputs
by GitHub issues - edited 06 May '23

06 May '23

alsa-project/alsa-lib issue #315 was edited from drjhe: I've come across a couple of USB-Audio speaker sets which get configured with non-existent S/PDIF outputs: - **Creative Pebble V3:** USB ID 041e:3272, ALSA name "Pebble V3" - **Jabra SPEAK 510:** USB ID 0b0e:0420, ALSA name "Jabra SPEAK 510 USB" - **'Ricco' Elite Silicon-based USB speakers:** USB ID 18c3:6255, ALSA name "USB Audio Device" The phantom outputs for the Pebble V3 and Jabra can be removed by adding ``` "Pebble V3" 999 "Jabra SPEAK 510 USB" 999 ``` to the ```USB-Audio.pcm.iec958_device``` section of USB-Audio.conf. For the Ricco speakers the ALSA name seems a bit too generic to add to USB-Audio.conf -- is there a way to achieve the same effect matching on the USB ID? Issue URL : https://github.com/alsa-project/alsa-lib/issues/315 Repository URL: https://github.com/alsa-project/alsa-lib

1 0

Some USB-Audio speakers with non-existent S/PDIF outputs
by GitHub issues - edited 06 May '23

06 May '23

alsa-project/alsa-lib issue #315 was edited from drjhe: I've come across a couple of USB-Audio speaker sets which get configured with non-existent S/PDIF outputs: - **Creative Pebble V3:** USB ID 041e:3272, ALSA name "Pebble V3" - **'Ricco' Elite Silicon-based USB speakers:** USB ID 18c3:6255, ALSA name "USB Audio Device" The phantom output for the Pebble V3 can be removed by adding ```"Pebble V3" 999``` to the ```USB-Audio.pcm.iec958_device``` section of USB-Audio.conf. For the Ricco speakers the ALSA name seems a bit too generic to add to USB-Audio.conf -- is there a way to achieve the same effect matching on the USB ID? Issue URL : https://github.com/alsa-project/alsa-lib/issues/315 Repository URL: https://github.com/alsa-project/alsa-lib

1 0

Some USB-Audio speakers with non-existent S/PDIF outputs
by GitHub issues - opened 06 May '23

06 May '23

alsa-project/alsa-lib issue #315 was opened from drjhe: I've come across a couple of USB-Audio speaker sets which get configured with non-existent S/PDIF outputs: - **Creative Pebble V3:** USB ID 041e:3272, ALSA name "Pebble V3" - **'Ricco' Elite Silicon-based USB speakers:** USB ID 18c3:6255, ALSA name "USB Audio Device" The phantom output for the Pebble V3 can be removed by adding ```"USB Audio Device" 999``` to the ```USB-Audio.pcm.iec958_device``` section of USB-Audio.conf. For the Ricco speakers the ALSA name seems a bit too generic to add to USB-Audio.conf -- is there a way to achieve the same effect matching on the USB ID? Issue URL : https://github.com/alsa-project/alsa-lib/issues/315 Repository URL: https://github.com/alsa-project/alsa-lib

1 0

Patch "spi: Replace all spi->chip_select and spi->cs_gpiod references with function call" has been added to the 6.3-stable tree
by Sasha Levin 06 May '23

06 May '23

This is a note to let you know that I've just added the patch titled spi: Replace all spi->chip_select and spi->cs_gpiod references with function call to the 6.3-stable tree which can be found at: http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=sum… The filename of the patch is: spi-replace-all-spi-chip_select-and-spi-cs_gpiod-ref.patch and it can be found in the queue-6.3 subdirectory. If you, or anyone else, feels it should not be added to the stable tree, please let <stable(a)vger.kernel.org> know about it. commit 37eb046d30e73ab12c596521b75a82ea5e97bbac Author: Amit Kumar Mahapatra via Alsa-devel <alsa-devel(a)alsa-project.org> Date: Fri Mar 10 23:02:03 2023 +0530 spi: Replace all spi->chip_select and spi->cs_gpiod references with function call [ Upstream commit 9e264f3f85a56cc109cc2d6010a48aa89d5c1ff1 ] Supporting multi-cs in spi drivers would require the chip_select & cs_gpiod members of struct spi_device to be an array. But changing the type of these members to array would break the spi driver functionality. To make the transition smoother introduced four new APIs to get/set the spi->chip_select & spi->cs_gpiod and replaced all spi->chip_select and spi->cs_gpiod references with get or set API calls. While adding multi-cs support in further patches the chip_select & cs_gpiod members of the spi_device structure would be converted to arrays & the "idx" parameter of the APIs would be used as array index i.e., spi->chip_select[idx] & spi->cs_gpiod[idx] respectively. Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra(a)amd.com> Acked-by: Heiko Stuebner <heiko(a)sntech.de> # Rockchip drivers Reviewed-by: Michal Simek <michal.simek(a)amd.com> Reviewed-by: Cédric Le Goater <clg(a)kaod.org> # Aspeed driver Reviewed-by: Dhruva Gole <d-gole(a)ti.com> # SPI Cadence QSPI Reviewed-by: Patrice Chotard <patrice.chotard(a)foss.st.com> # spi-stm32-qspi Acked-by: William Zhang <william.zhang(a)broadcom.com> # bcm63xx-hsspi driver Reviewed-by: Serge Semin <fancer.lancer(a)gmail.com> # DW SSI part Link: https://lore.kernel.org/r/167847070432.26.15076794204368669839@mailman-core… Signed-off-by: Mark Brown <broonie(a)kernel.org> Stable-dep-of: 45d2af82e0e6 ("spi: mchp-pci1xxxx: Fix improper implementation of disabling chip select lines") Signed-off-by: Sasha Levin <sashal(a)kernel.org> diff --git a/drivers/spi/spi-altera-core.c b/drivers/spi/spi-altera-core.c index 94fe6bf1b9a6a..87e37f48f196e 100644 --- a/drivers/spi/spi-altera-core.c +++ b/drivers/spi/spi-altera-core.c @@ -80,7 +80,7 @@ static void altera_spi_set_cs(struct spi_device *spi, bool is_high) altr_spi_writel(hw, ALTERA_SPI_TARGET_SEL, 0); } else { altr_spi_writel(hw, ALTERA_SPI_TARGET_SEL, - BIT(spi->chip_select)); + BIT(spi_get_chipselect(spi, 0))); hw->imr |= ALTERA_SPI_CONTROL_SSO_MSK; altr_spi_writel(hw, ALTERA_SPI_CONTROL, hw->imr); } diff --git a/drivers/spi/spi-amd.c b/drivers/spi/spi-amd.c index bfc3ab5f39eaa..fecead757a3cd 100644 --- a/drivers/spi/spi-amd.c +++ b/drivers/spi/spi-amd.c @@ -347,7 +347,7 @@ static inline int amd_spi_fifo_xfer(struct amd_spi *amd_spi, case AMD_SPI_V1: break; case AMD_SPI_V2: - amd_spi_clear_chip(amd_spi, message->spi->chip_select); + amd_spi_clear_chip(amd_spi, spi_get_chipselect(message->spi, 0)); break; default: return -ENODEV; @@ -364,7 +364,7 @@ static int amd_spi_master_transfer(struct spi_master *master, struct amd_spi *amd_spi = spi_master_get_devdata(master); struct spi_device *spi = msg->spi; - amd_spi_select_chip(amd_spi, spi->chip_select); + amd_spi_select_chip(amd_spi, spi_get_chipselect(spi, 0)); /* * Extract spi_transfers from the spi message and diff --git a/drivers/spi/spi-ar934x.c b/drivers/spi/spi-ar934x.c index 4a6ecaa0a9c9c..41ef6cf5c5851 100644 --- a/drivers/spi/spi-ar934x.c +++ b/drivers/spi/spi-ar934x.c @@ -125,7 +125,7 @@ static int ar934x_spi_transfer_one_message(struct spi_controller *ctlr, iowrite32(reg, sp->base + AR934X_SPI_DATAOUT); } - reg = AR934X_SPI_SHIFT_VAL(spi->chip_select, term, + reg = AR934X_SPI_SHIFT_VAL(spi_get_chipselect(spi, 0), term, trx_cur * 8); iowrite32(reg, sp->base + AR934X_SPI_REG_SHIFT_CTRL); stat = readl_poll_timeout( diff --git a/drivers/spi/spi-armada-3700.c b/drivers/spi/spi-armada-3700.c index 4d554b948d711..8584045fc17bb 100644 --- a/drivers/spi/spi-armada-3700.c +++ b/drivers/spi/spi-armada-3700.c @@ -437,9 +437,9 @@ static void a3700_spi_set_cs(struct spi_device *spi, bool enable) struct a3700_spi *a3700_spi = spi_controller_get_devdata(spi->controller); if (!enable) - a3700_spi_activate_cs(a3700_spi, spi->chip_select); + a3700_spi_activate_cs(a3700_spi, spi_get_chipselect(spi, 0)); else - a3700_spi_deactivate_cs(a3700_spi, spi->chip_select); + a3700_spi_deactivate_cs(a3700_spi, spi_get_chipselect(spi, 0)); } static void a3700_spi_header_set(struct a3700_spi *a3700_spi) diff --git a/drivers/spi/spi-aspeed-smc.c b/drivers/spi/spi-aspeed-smc.c index 873ff2cf72c9d..b7a9ec550ba16 100644 --- a/drivers/spi/spi-aspeed-smc.c +++ b/drivers/spi/spi-aspeed-smc.c @@ -296,7 +296,7 @@ static const struct aspeed_spi_data ast2400_spi_data; static int do_aspeed_spi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op) { struct aspeed_spi *aspi = spi_controller_get_devdata(mem->spi->master); - struct aspeed_spi_chip *chip = &aspi->chips[mem->spi->chip_select]; + struct aspeed_spi_chip *chip = &aspi->chips[spi_get_chipselect(mem->spi, 0)]; u32 addr_mode, addr_mode_backup; u32 ctl_val; int ret = 0; @@ -377,7 +377,8 @@ static const char *aspeed_spi_get_name(struct spi_mem *mem) struct aspeed_spi *aspi = spi_controller_get_devdata(mem->spi->master); struct device *dev = aspi->dev; - return devm_kasprintf(dev, GFP_KERNEL, "%s.%d", dev_name(dev), mem->spi->chip_select); + return devm_kasprintf(dev, GFP_KERNEL, "%s.%d", dev_name(dev), + spi_get_chipselect(mem->spi, 0)); } struct aspeed_spi_window { @@ -553,7 +554,7 @@ static int aspeed_spi_do_calibration(struct aspeed_spi_chip *chip); static int aspeed_spi_dirmap_create(struct spi_mem_dirmap_desc *desc) { struct aspeed_spi *aspi = spi_controller_get_devdata(desc->mem->spi->master); - struct aspeed_spi_chip *chip = &aspi->chips[desc->mem->spi->chip_select]; + struct aspeed_spi_chip *chip = &aspi->chips[spi_get_chipselect(desc->mem->spi, 0)]; struct spi_mem_op *op = &desc->info.op_tmpl; u32 ctl_val; int ret = 0; @@ -620,7 +621,7 @@ static ssize_t aspeed_spi_dirmap_read(struct spi_mem_dirmap_desc *desc, u64 offset, size_t len, void *buf) { struct aspeed_spi *aspi = spi_controller_get_devdata(desc->mem->spi->master); - struct aspeed_spi_chip *chip = &aspi->chips[desc->mem->spi->chip_select]; + struct aspeed_spi_chip *chip = &aspi->chips[spi_get_chipselect(desc->mem->spi, 0)]; /* Switch to USER command mode if mapping window is too small */ if (chip->ahb_window_size < offset + len) { @@ -670,7 +671,7 @@ static int aspeed_spi_setup(struct spi_device *spi) { struct aspeed_spi *aspi = spi_controller_get_devdata(spi->master); const struct aspeed_spi_data *data = aspi->data; - unsigned int cs = spi->chip_select; + unsigned int cs = spi_get_chipselect(spi, 0); struct aspeed_spi_chip *chip = &aspi->chips[cs]; chip->aspi = aspi; @@ -697,7 +698,7 @@ static int aspeed_spi_setup(struct spi_device *spi) static void aspeed_spi_cleanup(struct spi_device *spi) { struct aspeed_spi *aspi = spi_controller_get_devdata(spi->master); - unsigned int cs = spi->chip_select; + unsigned int cs = spi_get_chipselect(spi, 0); aspeed_spi_chip_enable(aspi, cs, false); diff --git a/drivers/spi/spi-at91-usart.c b/drivers/spi/spi-at91-usart.c index fab9d223e24a0..ca05c42ae4a5f 100644 --- a/drivers/spi/spi-at91-usart.c +++ b/drivers/spi/spi-at91-usart.c @@ -390,7 +390,7 @@ static int at91_usart_spi_setup(struct spi_device *spi) dev_dbg(&spi->dev, "setup: bpw %u mode 0x%x -> mr %d %08x\n", - spi->bits_per_word, spi->mode, spi->chip_select, mr); + spi->bits_per_word, spi->mode, spi_get_chipselect(spi, 0), mr); return 0; } diff --git a/drivers/spi/spi-ath79.c b/drivers/spi/spi-ath79.c index 795e88dbef1bd..6c2001cfa3d11 100644 --- a/drivers/spi/spi-ath79.c +++ b/drivers/spi/spi-ath79.c @@ -71,7 +71,7 @@ static void ath79_spi_chipselect(struct spi_device *spi, int is_active) { struct ath79_spi *sp = ath79_spidev_to_sp(spi); int cs_high = (spi->mode & SPI_CS_HIGH) ? is_active : !is_active; - u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select); + u32 cs_bit = AR71XX_SPI_IOC_CS(spi_get_chipselect(spi, 0)); if (cs_high) sp->ioc_base |= cs_bit; @@ -140,7 +140,7 @@ static int ath79_exec_mem_op(struct spi_mem *mem, struct ath79_spi *sp = ath79_spidev_to_sp(mem->spi); /* Ensures that reading is performed on device connected to hardware cs0 */ - if (mem->spi->chip_select || mem->spi->cs_gpiod) + if (spi_get_chipselect(mem->spi, 0) || spi_get_csgpiod(mem->spi, 0)) return -ENOTSUPP; /* Only use for fast-read op. */ diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c index 5c5678f065f33..7b17604a77608 100644 --- a/drivers/spi/spi-atmel.c +++ b/drivers/spi/spi-atmel.c @@ -327,10 +327,10 @@ static void cs_activate(struct atmel_spi *as, struct spi_device *spi) int chip_select; u32 mr; - if (spi->cs_gpiod) + if (spi_get_csgpiod(spi, 0)) chip_select = as->native_cs_for_gpio; else - chip_select = spi->chip_select; + chip_select = spi_get_chipselect(spi, 0); if (atmel_spi_is_v2(as)) { spi_writel(as, CSR0 + 4 * chip_select, asd->csr); @@ -378,10 +378,10 @@ static void cs_deactivate(struct atmel_spi *as, struct spi_device *spi) int chip_select; u32 mr; - if (spi->cs_gpiod) + if (spi_get_csgpiod(spi, 0)) chip_select = as->native_cs_for_gpio; else - chip_select = spi->chip_select; + chip_select = spi_get_chipselect(spi, 0); /* only deactivate *this* device; sometimes transfers to * another device may be active when this routine is called. @@ -394,7 +394,7 @@ static void cs_deactivate(struct atmel_spi *as, struct spi_device *spi) dev_dbg(&spi->dev, "DEactivate NPCS, mr %08x\n", mr); - if (!spi->cs_gpiod) + if (!spi_get_csgpiod(spi, 0)) spi_writel(as, CR, SPI_BIT(LASTXFER)); } @@ -800,10 +800,10 @@ static int atmel_spi_set_xfer_speed(struct atmel_spi *as, unsigned long bus_hz; int chip_select; - if (spi->cs_gpiod) + if (spi_get_csgpiod(spi, 0)) chip_select = as->native_cs_for_gpio; else - chip_select = spi->chip_select; + chip_select = spi_get_chipselect(spi, 0); /* v1 chips start out at half the peripheral bus speed. */ bus_hz = as->spi_clk; @@ -1189,7 +1189,7 @@ static int atmel_spi_setup(struct spi_device *spi) as = spi_controller_get_devdata(spi->controller); /* see notes above re chipselect */ - if (!spi->cs_gpiod && (spi->mode & SPI_CS_HIGH)) { + if (!spi_get_csgpiod(spi, 0) && (spi->mode & SPI_CS_HIGH)) { dev_warn(&spi->dev, "setup: non GPIO CS can't be active-high\n"); return -EINVAL; } @@ -1201,16 +1201,16 @@ static int atmel_spi_setup(struct spi_device *spi) */ initialize_native_cs_for_gpio(as); - if (spi->cs_gpiod && as->native_cs_free) { + if (spi_get_csgpiod(spi, 0) && as->native_cs_free) { dev_err(&spi->dev, "No native CS available to support this GPIO CS\n"); return -EBUSY; } - if (spi->cs_gpiod) + if (spi_get_csgpiod(spi, 0)) chip_select = as->native_cs_for_gpio; else - chip_select = spi->chip_select; + chip_select = spi_get_chipselect(spi, 0); csr = SPI_BF(BITS, bits - 8); if (spi->mode & SPI_CPOL) @@ -1218,7 +1218,7 @@ static int atmel_spi_setup(struct spi_device *spi) if (!(spi->mode & SPI_CPHA)) csr |= SPI_BIT(NCPHA); - if (!spi->cs_gpiod) + if (!spi_get_csgpiod(spi, 0)) csr |= SPI_BIT(CSAAT); csr |= SPI_BF(DLYBS, 0); @@ -1244,7 +1244,7 @@ static int atmel_spi_setup(struct spi_device *spi) dev_dbg(&spi->dev, "setup: bpw %u mode 0x%x -> csr%d %08x\n", - bits, spi->mode, spi->chip_select, csr); + bits, spi->mode, spi_get_chipselect(spi, 0), csr); if (!atmel_spi_is_v2(as)) spi_writel(as, CSR0 + 4 * chip_select, csr); diff --git a/drivers/spi/spi-au1550.c b/drivers/spi/spi-au1550.c index e008761298da4..da713cdfe0870 100644 --- a/drivers/spi/spi-au1550.c +++ b/drivers/spi/spi-au1550.c @@ -166,7 +166,7 @@ static void au1550_spi_chipsel(struct spi_device *spi, int value) switch (value) { case BITBANG_CS_INACTIVE: if (hw->pdata->deactivate_cs) - hw->pdata->deactivate_cs(hw->pdata, spi->chip_select, + hw->pdata->deactivate_cs(hw->pdata, spi_get_chipselect(spi, 0), cspol); break; @@ -211,7 +211,7 @@ static void au1550_spi_chipsel(struct spi_device *spi, int value) } while ((stat & PSC_SPISTAT_DR) == 0); if (hw->pdata->activate_cs) - hw->pdata->activate_cs(hw->pdata, spi->chip_select, + hw->pdata->activate_cs(hw->pdata, spi_get_chipselect(spi, 0), cspol); break; } diff --git a/drivers/spi/spi-axi-spi-engine.c b/drivers/spi/spi-axi-spi-engine.c index 80c3e38f5c1b5..1ff28784cfbb6 100644 --- a/drivers/spi/spi-axi-spi-engine.c +++ b/drivers/spi/spi-axi-spi-engine.c @@ -193,7 +193,7 @@ static void spi_engine_gen_cs(struct spi_engine_program *p, bool dry, unsigned int mask = 0xff; if (assert) - mask ^= BIT(spi->chip_select); + mask ^= BIT(spi_get_chipselect(spi, 0)); spi_engine_program_add_cmd(p, dry, SPI_ENGINE_CMD_ASSERT(1, mask)); } diff --git a/drivers/spi/spi-bcm-qspi.c b/drivers/spi/spi-bcm-qspi.c index 0eee574d3e1f2..7c2f1d1fb3f70 100644 --- a/drivers/spi/spi-bcm-qspi.c +++ b/drivers/spi/spi-bcm-qspi.c @@ -986,7 +986,7 @@ static int write_to_hw(struct bcm_qspi *qspi, struct spi_device *spi) if (has_bspi(qspi)) mspi_cdram &= ~1; else - mspi_cdram |= (~(1 << spi->chip_select) & + mspi_cdram |= (~(1 << spi_get_chipselect(spi, 0)) & MSPI_CDRAM_PCS); write_cdram_slot(qspi, slot, mspi_cdram); @@ -1046,8 +1046,8 @@ static int bcm_qspi_bspi_exec_mem_op(struct spi_device *spi, return -EIO; from = op->addr.val; - if (!spi->cs_gpiod) - bcm_qspi_chip_select(qspi, spi->chip_select); + if (!spi_get_csgpiod(spi, 0)) + bcm_qspi_chip_select(qspi, spi_get_chipselect(spi, 0)); bcm_qspi_write(qspi, MSPI, MSPI_WRITE_LOCK, 0); /* @@ -1126,8 +1126,8 @@ static int bcm_qspi_transfer_one(struct spi_master *master, int slots; unsigned long timeo = msecs_to_jiffies(100); - if (!spi->cs_gpiod) - bcm_qspi_chip_select(qspi, spi->chip_select); + if (!spi_get_csgpiod(spi, 0)) + bcm_qspi_chip_select(qspi, spi_get_chipselect(spi, 0)); qspi->trans_pos.trans = trans; qspi->trans_pos.byte = 0; diff --git a/drivers/spi/spi-bcm2835.c b/drivers/spi/spi-bcm2835.c index 747e03228c487..6b7a3fa93fdf6 100644 --- a/drivers/spi/spi-bcm2835.c +++ b/drivers/spi/spi-bcm2835.c @@ -1274,9 +1274,9 @@ static int bcm2835_spi_setup(struct spi_device *spi) * The SPI core has successfully requested the CS GPIO line from the * device tree, so we are done. */ - if (spi->cs_gpiod) + if (spi_get_csgpiod(spi, 0)) return 0; - if (spi->chip_select > 1) { + if (spi_get_chipselect(spi, 0) > 1) { /* error in the case of native CS requested with CS > 1 * officially there is a CS2, but it is not documented * which GPIO is connected with that... @@ -1301,18 +1301,19 @@ static int bcm2835_spi_setup(struct spi_device *spi) if (!chip) return 0; - spi->cs_gpiod = gpiochip_request_own_desc(chip, 8 - spi->chip_select, - DRV_NAME, - GPIO_LOOKUP_FLAGS_DEFAULT, - GPIOD_OUT_LOW); - if (IS_ERR(spi->cs_gpiod)) { - ret = PTR_ERR(spi->cs_gpiod); + spi_set_csgpiod(spi, 0, gpiochip_request_own_desc(chip, + 8 - (spi_get_chipselect(spi, 0)), + DRV_NAME, + GPIO_LOOKUP_FLAGS_DEFAULT, + GPIOD_OUT_LOW)); + if (IS_ERR(spi_get_csgpiod(spi, 0))) { + ret = PTR_ERR(spi_get_csgpiod(spi, 0)); goto err_cleanup; } /* and set up the "mode" and level */ dev_info(&spi->dev, "setting up native-CS%i to use GPIO\n", - spi->chip_select); + spi_get_chipselect(spi, 0)); return 0; diff --git a/drivers/spi/spi-bcm2835aux.c b/drivers/spi/spi-bcm2835aux.c index e285219223308..a3d8f6108477b 100644 --- a/drivers/spi/spi-bcm2835aux.c +++ b/drivers/spi/spi-bcm2835aux.c @@ -448,7 +448,7 @@ static int bcm2835aux_spi_setup(struct spi_device *spi) if (spi->mode & SPI_NO_CS) return 0; - if (spi->cs_gpiod) + if (spi_get_csgpiod(spi, 0)) return 0; /* for dt-backwards compatibility: only support native on CS0 @@ -465,7 +465,7 @@ static int bcm2835aux_spi_setup(struct spi_device *spi) dev_warn(&spi->dev, "Native CS is not supported - please configure cs-gpio in device-tree\n"); - if (spi->chip_select == 0) + if (spi_get_chipselect(spi, 0) == 0) return 0; dev_warn(&spi->dev, "Native CS is not working for cs > 0\n"); diff --git a/drivers/spi/spi-bcm63xx-hsspi.c b/drivers/spi/spi-bcm63xx-hsspi.c index cd0a6478f5e7b..d1aeae29fab9c 100644 --- a/drivers/spi/spi-bcm63xx-hsspi.c +++ b/drivers/spi/spi-bcm63xx-hsspi.c @@ -349,7 +349,7 @@ static int bcm63xx_hsspi_do_prepend_txrx(struct spi_device *spi, struct spi_transfer *t) { struct bcm63xx_hsspi *bs = spi_master_get_devdata(spi->master); - unsigned int chip_select = spi->chip_select; + unsigned int chip_select = spi_get_chipselect(spi, 0); u16 opcode = 0, val; const u8 *tx = t->tx_buf; u8 *rx = t->rx_buf; @@ -441,7 +441,7 @@ static void bcm63xx_hsspi_set_cs(struct bcm63xx_hsspi *bs, unsigned int cs, static void bcm63xx_hsspi_set_clk(struct bcm63xx_hsspi *bs, struct spi_device *spi, int hz) { - unsigned int profile = spi->chip_select; + unsigned int profile = spi_get_chipselect(spi, 0); u32 reg; reg = DIV_ROUND_UP(2048, DIV_ROUND_UP(bs->speed_hz, hz)); @@ -468,7 +468,7 @@ static void bcm63xx_hsspi_set_clk(struct bcm63xx_hsspi *bs, static int bcm63xx_hsspi_do_txrx(struct spi_device *spi, struct spi_transfer *t) { struct bcm63xx_hsspi *bs = spi_master_get_devdata(spi->master); - unsigned int chip_select = spi->chip_select; + unsigned int chip_select = spi_get_chipselect(spi, 0); u16 opcode = 0, val; int pending = t->len; int step_size = HSSPI_BUFFER_LEN; @@ -478,7 +478,7 @@ static int bcm63xx_hsspi_do_txrx(struct spi_device *spi, struct spi_transfer *t) bcm63xx_hsspi_set_clk(bs, spi, t->speed_hz); if (!t->cs_off) - bcm63xx_hsspi_set_cs(bs, spi->chip_select, true); + bcm63xx_hsspi_set_cs(bs, spi_get_chipselect(spi, 0), true); if (tx && rx) opcode = HSSPI_OP_READ_WRITE; @@ -545,14 +545,14 @@ static int bcm63xx_hsspi_setup(struct spi_device *spi) u32 reg; reg = __raw_readl(bs->regs + - HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select)); + HSSPI_PROFILE_SIGNAL_CTRL_REG(spi_get_chipselect(spi, 0))); reg &= ~(SIGNAL_CTRL_LAUNCH_RISING | SIGNAL_CTRL_LATCH_RISING); if (spi->mode & SPI_CPHA) reg |= SIGNAL_CTRL_LAUNCH_RISING; else reg |= SIGNAL_CTRL_LATCH_RISING; __raw_writel(reg, bs->regs + - HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select)); + HSSPI_PROFILE_SIGNAL_CTRL_REG(spi_get_chipselect(spi, 0))); mutex_lock(&bs->bus_mutex); reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG); @@ -560,16 +560,16 @@ static int bcm63xx_hsspi_setup(struct spi_device *spi) /* only change actual polarities if there is no transfer */ if ((reg & GLOBAL_CTRL_CS_POLARITY_MASK) == bs->cs_polarity) { if (spi->mode & SPI_CS_HIGH) - reg |= BIT(spi->chip_select); + reg |= BIT(spi_get_chipselect(spi, 0)); else - reg &= ~BIT(spi->chip_select); + reg &= ~BIT(spi_get_chipselect(spi, 0)); __raw_writel(reg, bs->regs + HSSPI_GLOBAL_CTRL_REG); } if (spi->mode & SPI_CS_HIGH) - bs->cs_polarity |= BIT(spi->chip_select); + bs->cs_polarity |= BIT(spi_get_chipselect(spi, 0)); else - bs->cs_polarity &= ~BIT(spi->chip_select); + bs->cs_polarity &= ~BIT(spi_get_chipselect(spi, 0)); mutex_unlock(&bs->bus_mutex); @@ -600,7 +600,7 @@ static int bcm63xx_hsspi_do_dummy_cs_txrx(struct spi_device *spi, * e. At the end restore the polarities again to their default values. */ - dummy_cs = !spi->chip_select; + dummy_cs = !spi_get_chipselect(spi, 0); bcm63xx_hsspi_set_cs(bs, dummy_cs, true); list_for_each_entry(t, &msg->transfers, transfer_list) { @@ -633,22 +633,22 @@ static int bcm63xx_hsspi_do_dummy_cs_txrx(struct spi_device *spi, keep_cs = true; } else { if (!t->cs_off) - bcm63xx_hsspi_set_cs(bs, spi->chip_select, false); + bcm63xx_hsspi_set_cs(bs, spi_get_chipselect(spi, 0), false); spi_transfer_cs_change_delay_exec(msg, t); if (!list_next_entry(t, transfer_list)->cs_off) - bcm63xx_hsspi_set_cs(bs, spi->chip_select, true); + bcm63xx_hsspi_set_cs(bs, spi_get_chipselect(spi, 0), true); } } else if (!list_is_last(&t->transfer_list, &msg->transfers) && t->cs_off != list_next_entry(t, transfer_list)->cs_off) { - bcm63xx_hsspi_set_cs(bs, spi->chip_select, t->cs_off); + bcm63xx_hsspi_set_cs(bs, spi_get_chipselect(spi, 0), t->cs_off); } } bcm63xx_hsspi_set_cs(bs, dummy_cs, false); if (status || !keep_cs) - bcm63xx_hsspi_set_cs(bs, spi->chip_select, false); + bcm63xx_hsspi_set_cs(bs, spi_get_chipselect(spi, 0), false); return status; } diff --git a/drivers/spi/spi-bcm63xx.c b/drivers/spi/spi-bcm63xx.c index 3686d78c44a6d..787625ce700cb 100644 --- a/drivers/spi/spi-bcm63xx.c +++ b/drivers/spi/spi-bcm63xx.c @@ -292,7 +292,7 @@ static int bcm63xx_txrx_bufs(struct spi_device *spi, struct spi_transfer *first, /* Issue the transfer */ cmd = SPI_CMD_START_IMMEDIATE; cmd |= (prepend_len << SPI_CMD_PREPEND_BYTE_CNT_SHIFT); - cmd |= (spi->chip_select << SPI_CMD_DEVICE_ID_SHIFT); + cmd |= (spi_get_chipselect(spi, 0) << SPI_CMD_DEVICE_ID_SHIFT); bcm_spi_writew(bs, cmd, SPI_CMD); /* Enable the CMD_DONE interrupt */ diff --git a/drivers/spi/spi-bcmbca-hsspi.c b/drivers/spi/spi-bcmbca-hsspi.c index 3f9e6131ad863..2306bf879784c 100644 --- a/drivers/spi/spi-bcmbca-hsspi.c +++ b/drivers/spi/spi-bcmbca-hsspi.c @@ -193,7 +193,7 @@ static void bcmbca_hsspi_set_cs(struct bcmbca_hsspi *bs, unsigned int cs, static void bcmbca_hsspi_set_clk(struct bcmbca_hsspi *bs, struct spi_device *spi, int hz) { - unsigned int profile = spi->chip_select; + unsigned int profile = spi_get_chipselect(spi, 0); u32 reg; reg = DIV_ROUND_UP(2048, DIV_ROUND_UP(bs->speed_hz, hz)); @@ -251,7 +251,7 @@ static int bcmbca_hsspi_do_txrx(struct spi_device *spi, struct spi_transfer *t, struct spi_message *msg) { struct bcmbca_hsspi *bs = spi_master_get_devdata(spi->master); - unsigned int chip_select = spi->chip_select; + unsigned int chip_select = spi_get_chipselect(spi, 0); u16 opcode = 0, val; int pending = t->len; int step_size = HSSPI_BUFFER_LEN; @@ -312,7 +312,7 @@ static int bcmbca_hsspi_do_txrx(struct spi_device *spi, struct spi_transfer *t, PINGPONG_COMMAND_START_NOW; __raw_writel(reg, bs->regs + HSSPI_PINGPONG_COMMAND_REG(0)); - if (bcmbca_hsspi_wait_cmd(bs, spi->chip_select)) + if (bcmbca_hsspi_wait_cmd(bs, spi_get_chipselect(spi, 0))) return -ETIMEDOUT; pending -= curr_step; @@ -332,33 +332,33 @@ static int bcmbca_hsspi_setup(struct spi_device *spi) u32 reg; reg = __raw_readl(bs->regs + - HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select)); + HSSPI_PROFILE_SIGNAL_CTRL_REG(spi_get_chipselect(spi, 0))); reg &= ~(SIGNAL_CTRL_LAUNCH_RISING | SIGNAL_CTRL_LATCH_RISING); if (spi->mode & SPI_CPHA) reg |= SIGNAL_CTRL_LAUNCH_RISING; else reg |= SIGNAL_CTRL_LATCH_RISING; __raw_writel(reg, bs->regs + - HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select)); + HSSPI_PROFILE_SIGNAL_CTRL_REG(spi_get_chipselect(spi, 0))); mutex_lock(&bs->bus_mutex); reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG); if (spi->mode & SPI_CS_HIGH) - reg |= BIT(spi->chip_select); + reg |= BIT(spi_get_chipselect(spi, 0)); else - reg &= ~BIT(spi->chip_select); + reg &= ~BIT(spi_get_chipselect(spi, 0)); __raw_writel(reg, bs->regs + HSSPI_GLOBAL_CTRL_REG); if (spi->mode & SPI_CS_HIGH) - bs->cs_polarity |= BIT(spi->chip_select); + bs->cs_polarity |= BIT(spi_get_chipselect(spi, 0)); else - bs->cs_polarity &= ~BIT(spi->chip_select); + bs->cs_polarity &= ~BIT(spi_get_chipselect(spi, 0)); reg = __raw_readl(bs->spim_ctrl); - reg &= ~BIT(spi->chip_select + SPIM_CTRL_CS_OVERRIDE_VAL_SHIFT); + reg &= ~BIT(spi_get_chipselect(spi, 0) + SPIM_CTRL_CS_OVERRIDE_VAL_SHIFT); if (spi->mode & SPI_CS_HIGH) - reg |= BIT(spi->chip_select + SPIM_CTRL_CS_OVERRIDE_VAL_SHIFT); + reg |= BIT(spi_get_chipselect(spi, 0) + SPIM_CTRL_CS_OVERRIDE_VAL_SHIFT); __raw_writel(reg, bs->spim_ctrl); mutex_unlock(&bs->bus_mutex); @@ -388,16 +388,16 @@ static int bcmbca_hsspi_transfer_one(struct spi_master *master, keep_cs = true; } else { if (!t->cs_off) - bcmbca_hsspi_set_cs(bs, spi->chip_select, false); + bcmbca_hsspi_set_cs(bs, spi_get_chipselect(spi, 0), false); spi_transfer_cs_change_delay_exec(msg, t); if (!list_next_entry(t, transfer_list)->cs_off) - bcmbca_hsspi_set_cs(bs, spi->chip_select, true); + bcmbca_hsspi_set_cs(bs, spi_get_chipselect(spi, 0), true); } } else if (!list_is_last(&t->transfer_list, &msg->transfers) && t->cs_off != list_next_entry(t, transfer_list)->cs_off) { - bcmbca_hsspi_set_cs(bs, spi->chip_select, t->cs_off); + bcmbca_hsspi_set_cs(bs, spi_get_chipselect(spi, 0), t->cs_off); } msg->actual_length += t->len; @@ -406,7 +406,7 @@ static int bcmbca_hsspi_transfer_one(struct spi_master *master, mutex_unlock(&bs->msg_mutex); if (status || !keep_cs) - bcmbca_hsspi_set_cs(bs, spi->chip_select, false); + bcmbca_hsspi_set_cs(bs, spi_get_chipselect(spi, 0), false); msg->status = status; spi_finalize_current_message(master); diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c index 64b6a460d739b..fb6d85fd2e864 100644 --- a/drivers/spi/spi-cadence-quadspi.c +++ b/drivers/spi/spi-cadence-quadspi.c @@ -1355,7 +1355,7 @@ static int cqspi_mem_process(struct spi_mem *mem, const struct spi_mem_op *op) struct cqspi_st *cqspi = spi_master_get_devdata(mem->spi->master); struct cqspi_flash_pdata *f_pdata; - f_pdata = &cqspi->f_pdata[mem->spi->chip_select]; + f_pdata = &cqspi->f_pdata[spi_get_chipselect(mem->spi, 0)]; cqspi_configure(f_pdata, mem->spi->max_speed_hz); if (op->data.dir == SPI_MEM_DATA_IN && op->data.buf.in) { @@ -1561,7 +1561,8 @@ static const char *cqspi_get_name(struct spi_mem *mem) struct cqspi_st *cqspi = spi_master_get_devdata(mem->spi->master); struct device *dev = &cqspi->pdev->dev; - return devm_kasprintf(dev, GFP_KERNEL, "%s.%d", dev_name(dev), mem->spi->chip_select); + return devm_kasprintf(dev, GFP_KERNEL, "%s.%d", dev_name(dev), + spi_get_chipselect(mem->spi, 0)); } static const struct spi_controller_mem_ops cqspi_mem_ops = { diff --git a/drivers/spi/spi-cadence-xspi.c b/drivers/spi/spi-cadence-xspi.c index 91db3c973167b..ce4a3145f065b 100644 --- a/drivers/spi/spi-cadence-xspi.c +++ b/drivers/spi/spi-cadence-xspi.c @@ -409,8 +409,8 @@ static int cdns_xspi_mem_op(struct cdns_xspi_dev *cdns_xspi, { enum spi_mem_data_dir dir = op->data.dir; - if (cdns_xspi->cur_cs != mem->spi->chip_select) - cdns_xspi->cur_cs = mem->spi->chip_select; + if (cdns_xspi->cur_cs != spi_get_chipselect(mem->spi, 0)) + cdns_xspi->cur_cs = spi_get_chipselect(mem->spi, 0); return cdns_xspi_send_stig_command(cdns_xspi, op, (dir != SPI_MEM_NO_DATA)); diff --git a/drivers/spi/spi-cadence.c b/drivers/spi/spi-cadence.c index 6a7f7df1e7764..4ec778de5baf5 100644 --- a/drivers/spi/spi-cadence.c +++ b/drivers/spi/spi-cadence.c @@ -185,11 +185,11 @@ static void cdns_spi_chipselect(struct spi_device *spi, bool is_high) /* Select the slave */ ctrl_reg &= ~CDNS_SPI_CR_SSCTRL; if (!(xspi->is_decoded_cs)) - ctrl_reg |= ((~(CDNS_SPI_SS0 << spi->chip_select)) << + ctrl_reg |= ((~(CDNS_SPI_SS0 << spi_get_chipselect(spi, 0))) << CDNS_SPI_SS_SHIFT) & CDNS_SPI_CR_SSCTRL; else - ctrl_reg |= (spi->chip_select << CDNS_SPI_SS_SHIFT) & + ctrl_reg |= (spi_get_chipselect(spi, 0) << CDNS_SPI_SS_SHIFT) & CDNS_SPI_CR_SSCTRL; } diff --git a/drivers/spi/spi-cavium.c b/drivers/spi/spi-cavium.c index 6854c3ce423b3..dfe224defd6ed 100644 --- a/drivers/spi/spi-cavium.c +++ b/drivers/spi/spi-cavium.c @@ -57,8 +57,8 @@ static int octeon_spi_do_transfer(struct octeon_spi *p, mpi_cfg.s.cslate = cpha ? 1 : 0; mpi_cfg.s.enable = 1; - if (spi->chip_select < 4) - p->cs_enax |= 1ull << (12 + spi->chip_select); + if (spi_get_chipselect(spi, 0) < 4) + p->cs_enax |= 1ull << (12 + spi_get_chipselect(spi, 0)); mpi_cfg.u64 |= p->cs_enax; if (mpi_cfg.u64 != p->last_cfg) { @@ -78,7 +78,7 @@ static int octeon_spi_do_transfer(struct octeon_spi *p, writeq(d, p->register_base + OCTEON_SPI_DAT0(p) + (8 * i)); } mpi_tx.u64 = 0; - mpi_tx.s.csid = spi->chip_select; + mpi_tx.s.csid = spi_get_chipselect(spi, 0); mpi_tx.s.leavecs = 1; mpi_tx.s.txnum = tx_buf ? OCTEON_SPI_MAX_BYTES : 0; mpi_tx.s.totnum = OCTEON_SPI_MAX_BYTES; @@ -103,7 +103,7 @@ static int octeon_spi_do_transfer(struct octeon_spi *p, } mpi_tx.u64 = 0; - mpi_tx.s.csid = spi->chip_select; + mpi_tx.s.csid = spi_get_chipselect(spi, 0); if (last_xfer) mpi_tx.s.leavecs = xfer->cs_change; else diff --git a/drivers/spi/spi-coldfire-qspi.c b/drivers/spi/spi-coldfire-qspi.c index 263ce90473277..18e4fd86b2f28 100644 --- a/drivers/spi/spi-coldfire-qspi.c +++ b/drivers/spi/spi-coldfire-qspi.c @@ -290,9 +290,9 @@ static void mcfqspi_set_cs(struct spi_device *spi, bool enable) bool cs_high = spi->mode & SPI_CS_HIGH; if (enable) - mcfqspi_cs_select(mcfqspi, spi->chip_select, cs_high); + mcfqspi_cs_select(mcfqspi, spi_get_chipselect(spi, 0), cs_high); else - mcfqspi_cs_deselect(mcfqspi, spi->chip_select, cs_high); + mcfqspi_cs_deselect(mcfqspi, spi_get_chipselect(spi, 0), cs_high); } static int mcfqspi_transfer_one(struct spi_master *master, @@ -324,11 +324,11 @@ static int mcfqspi_transfer_one(struct spi_master *master, static int mcfqspi_setup(struct spi_device *spi) { mcfqspi_cs_deselect(spi_master_get_devdata(spi->master), - spi->chip_select, spi->mode & SPI_CS_HIGH); + spi_get_chipselect(spi, 0), spi->mode & SPI_CS_HIGH); dev_dbg(&spi->dev, "bits per word %d, chip select %d, speed %d KHz\n", - spi->bits_per_word, spi->chip_select, + spi->bits_per_word, spi_get_chipselect(spi, 0), (MCFQSPI_BUSCLK / mcfqspi_qmr_baud(spi->max_speed_hz)) / 1000); diff --git a/drivers/spi/spi-davinci.c b/drivers/spi/spi-davinci.c index d112c2cac042b..55c9abcb8e3b3 100644 --- a/drivers/spi/spi-davinci.c +++ b/drivers/spi/spi-davinci.c @@ -199,7 +199,7 @@ static void davinci_spi_chipselect(struct spi_device *spi, int value) { struct davinci_spi *dspi; struct davinci_spi_config *spicfg = spi->controller_data; - u8 chip_sel = spi->chip_select; + u8 chip_sel = spi_get_chipselect(spi, 0); u16 spidat1 = CS_DEFAULT; dspi = spi_master_get_devdata(spi->master); @@ -212,11 +212,11 @@ static void davinci_spi_chipselect(struct spi_device *spi, int value) * Board specific chip select logic decides the polarity and cs * line for the controller */ - if (spi->cs_gpiod) { + if (spi_get_csgpiod(spi, 0)) { if (value == BITBANG_CS_ACTIVE) - gpiod_set_value(spi->cs_gpiod, 1); + gpiod_set_value(spi_get_csgpiod(spi, 0), 1); else - gpiod_set_value(spi->cs_gpiod, 0); + gpiod_set_value(spi_get_csgpiod(spi, 0), 0); } else { if (value == BITBANG_CS_ACTIVE) { if (!(spi->mode & SPI_CS_WORD)) @@ -293,11 +293,11 @@ static int davinci_spi_setup_transfer(struct spi_device *spi, if (bits_per_word <= 8) { dspi->get_rx = davinci_spi_rx_buf_u8; dspi->get_tx = davinci_spi_tx_buf_u8; - dspi->bytes_per_word[spi->chip_select] = 1; + dspi->bytes_per_word[spi_get_chipselect(spi, 0)] = 1; } else { dspi->get_rx = davinci_spi_rx_buf_u16; dspi->get_tx = davinci_spi_tx_buf_u16; - dspi->bytes_per_word[spi->chip_select] = 2; + dspi->bytes_per_word[spi_get_chipselect(spi, 0)] = 2; } if (!hz) @@ -415,11 +415,11 @@ static int davinci_spi_setup(struct spi_device *spi) dspi = spi_master_get_devdata(spi->master); if (!(spi->mode & SPI_NO_CS)) { - if (np && spi->cs_gpiod) + if (np && spi_get_csgpiod(spi, 0)) internal_cs = false; if (internal_cs) - set_io_bits(dspi->base + SPIPC0, 1 << spi->chip_select); + set_io_bits(dspi->base + SPIPC0, 1 << spi_get_chipselect(spi, 0)); } if (spi->mode & SPI_READY) @@ -579,7 +579,7 @@ static int davinci_spi_bufs(struct spi_device *spi, struct spi_transfer *t) spicfg = &davinci_spi_default_cfg; /* convert len to words based on bits_per_word */ - data_type = dspi->bytes_per_word[spi->chip_select]; + data_type = dspi->bytes_per_word[spi_get_chipselect(spi, 0)]; dspi->tx = t->tx_buf; dspi->rx = t->rx_buf; diff --git a/drivers/spi/spi-dln2.c b/drivers/spi/spi-dln2.c index 0a1fb2bc9e546..5e60e3d5822e7 100644 --- a/drivers/spi/spi-dln2.c +++ b/drivers/spi/spi-dln2.c @@ -596,12 +596,12 @@ static int dln2_spi_prepare_message(struct spi_master *master, struct dln2_spi *dln2 = spi_master_get_devdata(master); struct spi_device *spi = message->spi; - if (dln2->cs != spi->chip_select) { - ret = dln2_spi_cs_set_one(dln2, spi->chip_select); + if (dln2->cs != spi_get_chipselect(spi, 0)) { + ret = dln2_spi_cs_set_one(dln2, spi_get_chipselect(spi, 0)); if (ret < 0) return ret; - dln2->cs = spi->chip_select; + dln2->cs = spi_get_chipselect(spi, 0); } return 0; diff --git a/drivers/spi/spi-dw-core.c b/drivers/spi/spi-dw-core.c index c3bfb6c84cab2..ae3108c70f508 100644 --- a/drivers/spi/spi-dw-core.c +++ b/drivers/spi/spi-dw-core.c @@ -103,7 +103,7 @@ void dw_spi_set_cs(struct spi_device *spi, bool enable) * support active-high or active-low CS level. */ if (cs_high == enable) - dw_writel(dws, DW_SPI_SER, BIT(spi->chip_select)); + dw_writel(dws, DW_SPI_SER, BIT(spi_get_chipselect(spi, 0))); else dw_writel(dws, DW_SPI_SER, 0); } diff --git a/drivers/spi/spi-dw-mmio.c b/drivers/spi/spi-dw-mmio.c index 26c40ea6dd129..d511da766ce82 100644 --- a/drivers/spi/spi-dw-mmio.c +++ b/drivers/spi/spi-dw-mmio.c @@ -65,7 +65,7 @@ static void dw_spi_mscc_set_cs(struct spi_device *spi, bool enable) struct dw_spi *dws = spi_master_get_devdata(spi->master); struct dw_spi_mmio *dwsmmio = container_of(dws, struct dw_spi_mmio, dws); struct dw_spi_mscc *dwsmscc = dwsmmio->priv; - u32 cs = spi->chip_select; + u32 cs = spi_get_chipselect(spi, 0); if (cs < 4) { u32 sw_mode = MSCC_SPI_MST_SW_MODE_SW_PIN_CTRL_MODE; @@ -138,7 +138,7 @@ static void dw_spi_sparx5_set_cs(struct spi_device *spi, bool enable) struct dw_spi *dws = spi_master_get_devdata(spi->master); struct dw_spi_mmio *dwsmmio = container_of(dws, struct dw_spi_mmio, dws); struct dw_spi_mscc *dwsmscc = dwsmmio->priv; - u8 cs = spi->chip_select; + u8 cs = spi_get_chipselect(spi, 0); if (!enable) { /* CS override drive enable */ diff --git a/drivers/spi/spi-falcon.c b/drivers/spi/spi-falcon.c index a7d4dffac66b2..4c103dff0d445 100644 --- a/drivers/spi/spi-falcon.c +++ b/drivers/spi/spi-falcon.c @@ -131,7 +131,7 @@ int falcon_sflash_xfer(struct spi_device *spi, struct spi_transfer *t, * especially alen and dumlen. */ - priv->sfcmd = ((spi->chip_select + priv->sfcmd = ((spi_get_chipselect(spi, 0) << SFCMD_CS_OFFSET) & SFCMD_CS_MASK); priv->sfcmd |= SFCMD_KEEP_CS_KEEP_SELECTED; diff --git a/drivers/spi/spi-fsi.c b/drivers/spi/spi-fsi.c index cf1e4f9ebd727..ba3b17d7c9ec2 100644 --- a/drivers/spi/spi-fsi.c +++ b/drivers/spi/spi-fsi.c @@ -425,7 +425,7 @@ static int fsi_spi_transfer_one_message(struct spi_controller *ctlr, struct spi_message *mesg) { int rc; - u8 seq_slave = SPI_FSI_SEQUENCE_SEL_SLAVE(mesg->spi->chip_select + 1); + u8 seq_slave = SPI_FSI_SEQUENCE_SEL_SLAVE(spi_get_chipselect(mesg->spi, 0) + 1); unsigned int len; struct spi_transfer *transfer; struct fsi_spi *ctx = spi_controller_get_devdata(ctlr); diff --git a/drivers/spi/spi-fsl-dspi.c b/drivers/spi/spi-fsl-dspi.c index e419642eb10e5..0f9a97ee2e772 100644 --- a/drivers/spi/spi-fsl-dspi.c +++ b/drivers/spi/spi-fsl-dspi.c @@ -902,19 +902,19 @@ static irqreturn_t dspi_interrupt(int irq, void *dev_id) static void dspi_assert_cs(struct spi_device *spi, bool *cs) { - if (!spi->cs_gpiod || *cs) + if (!spi_get_csgpiod(spi, 0) || *cs) return; - gpiod_set_value_cansleep(spi->cs_gpiod, true); + gpiod_set_value_cansleep(spi_get_csgpiod(spi, 0), true); *cs = true; } static void dspi_deassert_cs(struct spi_device *spi, bool *cs) { - if (!spi->cs_gpiod || !*cs) + if (!spi_get_csgpiod(spi, 0) || !*cs) return; - gpiod_set_value_cansleep(spi->cs_gpiod, false); + gpiod_set_value_cansleep(spi_get_csgpiod(spi, 0), false); *cs = false; } @@ -938,8 +938,8 @@ static int dspi_transfer_one_message(struct spi_controller *ctlr, /* Prepare command word for CMD FIFO */ dspi->tx_cmd = SPI_PUSHR_CMD_CTAS(0); - if (!spi->cs_gpiod) - dspi->tx_cmd |= SPI_PUSHR_CMD_PCS(spi->chip_select); + if (!spi_get_csgpiod(spi, 0)) + dspi->tx_cmd |= SPI_PUSHR_CMD_PCS(spi_get_chipselect(spi, 0)); if (list_is_last(&dspi->cur_transfer->transfer_list, &dspi->cur_msg->transfers)) { @@ -1058,7 +1058,7 @@ static int dspi_setup(struct spi_device *spi) chip->ctar_val |= SPI_CTAR_LSBFE; } - gpiod_direction_output(spi->cs_gpiod, false); + gpiod_direction_output(spi_get_csgpiod(spi, 0), false); dspi_deassert_cs(spi, &cs); spi_set_ctldata(spi, chip); @@ -1071,7 +1071,7 @@ static void dspi_cleanup(struct spi_device *spi) struct chip_data *chip = spi_get_ctldata((struct spi_device *)spi); dev_dbg(&spi->dev, "spi_device %u.%u cleanup\n", - spi->controller->bus_num, spi->chip_select); + spi->controller->bus_num, spi_get_chipselect(spi, 0)); kfree(chip); } diff --git a/drivers/spi/spi-fsl-espi.c b/drivers/spi/spi-fsl-espi.c index f7066bef7b06f..b593055e3d6d5 100644 --- a/drivers/spi/spi-fsl-espi.c +++ b/drivers/spi/spi-fsl-espi.c @@ -345,7 +345,7 @@ static void fsl_espi_setup_transfer(struct spi_device *spi, /* don't write the mode register if the mode doesn't change */ if (cs->hw_mode != hw_mode_old) - fsl_espi_write_reg(espi, ESPI_SPMODEx(spi->chip_select), + fsl_espi_write_reg(espi, ESPI_SPMODEx(spi_get_chipselect(spi, 0)), cs->hw_mode); } @@ -359,7 +359,7 @@ static int fsl_espi_bufs(struct spi_device *spi, struct spi_transfer *t) reinit_completion(&espi->done); /* Set SPCOM[CS] and SPCOM[TRANLEN] field */ - spcom = SPCOM_CS(spi->chip_select); + spcom = SPCOM_CS(spi_get_chipselect(spi, 0)); spcom |= SPCOM_TRANLEN(t->len - 1); /* configure RXSKIP mode */ @@ -492,7 +492,7 @@ static int fsl_espi_setup(struct spi_device *spi) pm_runtime_get_sync(espi->dev); - cs->hw_mode = fsl_espi_read_reg(espi, ESPI_SPMODEx(spi->chip_select)); + cs->hw_mode = fsl_espi_read_reg(espi, ESPI_SPMODEx(spi_get_chipselect(spi, 0))); /* mask out bits we are going to set */ cs->hw_mode &= ~(CSMODE_CP_BEGIN_EDGECLK | CSMODE_CI_INACTIVEHIGH | CSMODE_REV); diff --git a/drivers/spi/spi-fsl-lpspi.c b/drivers/spi/spi-fsl-lpspi.c index 34488de555871..fe69ec8c9d688 100644 --- a/drivers/spi/spi-fsl-lpspi.c +++ b/drivers/spi/spi-fsl-lpspi.c @@ -425,7 +425,7 @@ static int fsl_lpspi_setup_transfer(struct spi_controller *controller, if (fsl_lpspi->is_only_cs1) fsl_lpspi->config.chip_select = 1; else - fsl_lpspi->config.chip_select = spi->chip_select; + fsl_lpspi->config.chip_select = spi_get_chipselect(spi, 0); if (!fsl_lpspi->config.speed_hz) fsl_lpspi->config.speed_hz = spi->max_speed_hz; diff --git a/drivers/spi/spi-fsl-qspi.c b/drivers/spi/spi-fsl-qspi.c index 85cc71ba624a9..4f16d4676650d 100644 --- a/drivers/spi/spi-fsl-qspi.c +++ b/drivers/spi/spi-fsl-qspi.c @@ -528,7 +528,7 @@ static void fsl_qspi_select_mem(struct fsl_qspi *q, struct spi_device *spi) unsigned long rate = spi->max_speed_hz; int ret; - if (q->selected == spi->chip_select) + if (q->selected == spi_get_chipselect(spi, 0)) return; if (needs_4x_clock(q)) @@ -544,7 +544,7 @@ static void fsl_qspi_select_mem(struct fsl_qspi *q, struct spi_device *spi) if (ret) return; - q->selected = spi->chip_select; + q->selected = spi_get_chipselect(spi, 0); fsl_qspi_invalidate(q); } @@ -823,7 +823,7 @@ static const char *fsl_qspi_get_name(struct spi_mem *mem) name = devm_kasprintf(dev, GFP_KERNEL, "%s-%d", dev_name(q->dev), - mem->spi->chip_select); + spi_get_chipselect(mem->spi, 0)); if (!name) { dev_err(dev, "failed to get memory for custom flash name\n"); diff --git a/drivers/spi/spi-fsl-spi.c b/drivers/spi/spi-fsl-spi.c index 93152144fd2ec..08fa6e38f4eba 100644 --- a/drivers/spi/spi-fsl-spi.c +++ b/drivers/spi/spi-fsl-spi.c @@ -503,7 +503,7 @@ static void fsl_spi_grlib_cs_control(struct spi_device *spi, bool on) struct mpc8xxx_spi *mpc8xxx_spi = spi_master_get_devdata(spi->master); struct fsl_spi_reg __iomem *reg_base = mpc8xxx_spi->reg_base; u32 slvsel; - u16 cs = spi->chip_select; + u16 cs = spi_get_chipselect(spi, 0); if (cs < mpc8xxx_spi->native_chipselects) { slvsel = mpc8xxx_spi_read_reg(&reg_base->slvsel); diff --git a/drivers/spi/spi-geni-qcom.c b/drivers/spi/spi-geni-qcom.c index babb039bcb431..301e55fcbde9b 100644 --- a/drivers/spi/spi-geni-qcom.c +++ b/drivers/spi/spi-geni-qcom.c @@ -391,9 +391,9 @@ static int setup_fifo_params(struct spi_device *spi_slv, cpha = CPHA; if (spi_slv->mode & SPI_CS_HIGH) - demux_output_inv = BIT(spi_slv->chip_select); + demux_output_inv = BIT(spi_get_chipselect(spi_slv, 0)); - demux_sel = spi_slv->chip_select; + demux_sel = spi_get_chipselect(spi_slv, 0); mas->cur_bits_per_word = spi_slv->bits_per_word; spi_setup_word_len(mas, spi_slv->mode, spi_slv->bits_per_word); @@ -469,7 +469,7 @@ static int setup_gsi_xfer(struct spi_transfer *xfer, struct spi_geni_master *mas peripheral.loopback_en = !!(spi_slv->mode & SPI_LOOP); peripheral.clock_pol_high = !!(spi_slv->mode & SPI_CPOL); peripheral.data_pol_high = !!(spi_slv->mode & SPI_CPHA); - peripheral.cs = spi_slv->chip_select; + peripheral.cs = spi_get_chipselect(spi_slv, 0); peripheral.pack_en = true; peripheral.word_len = xfer->bits_per_word - MIN_WORD_LEN; diff --git a/drivers/spi/spi-gpio.c b/drivers/spi/spi-gpio.c index 9c8c7948044ed..092afc7679d40 100644 --- a/drivers/spi/spi-gpio.c +++ b/drivers/spi/spi-gpio.c @@ -230,7 +230,7 @@ static void spi_gpio_chipselect(struct spi_device *spi, int is_active) /* Drive chip select line, if we have one */ if (spi_gpio->cs_gpios) { - struct gpio_desc *cs = spi_gpio->cs_gpios[spi->chip_select]; + struct gpio_desc *cs = spi_gpio->cs_gpios[spi_get_chipselect(spi, 0)]; /* SPI chip selects are normally active-low */ gpiod_set_value_cansleep(cs, (spi->mode & SPI_CS_HIGH) ? is_active : !is_active); @@ -248,7 +248,7 @@ static int spi_gpio_setup(struct spi_device *spi) * initialized from the descriptor lookup. */ if (spi_gpio->cs_gpios) { - cs = spi_gpio->cs_gpios[spi->chip_select]; + cs = spi_gpio->cs_gpios[spi_get_chipselect(spi, 0)]; if (!spi->controller_state && cs) status = gpiod_direction_output(cs, !(spi->mode & SPI_CS_HIGH)); diff --git a/drivers/spi/spi-gxp.c b/drivers/spi/spi-gxp.c index c900c2f39b578..684d63f402f34 100644 --- a/drivers/spi/spi-gxp.c +++ b/drivers/spi/spi-gxp.c @@ -201,7 +201,7 @@ static ssize_t gxp_spi_write(struct gxp_spi_chip *chip, const struct spi_mem_op static int do_gxp_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op) { struct gxp_spi *spifi = spi_controller_get_devdata(mem->spi->master); - struct gxp_spi_chip *chip = &spifi->chips[mem->spi->chip_select]; + struct gxp_spi_chip *chip = &spifi->chips[spi_get_chipselect(mem->spi, 0)]; int ret; if (op->data.dir == SPI_MEM_DATA_IN) { @@ -237,7 +237,7 @@ static const struct spi_controller_mem_ops gxp_spi_mem_ops = { static int gxp_spi_setup(struct spi_device *spi) { struct gxp_spi *spifi = spi_controller_get_devdata(spi->master); - unsigned int cs = spi->chip_select; + unsigned int cs = spi_get_chipselect(spi, 0); struct gxp_spi_chip *chip = &spifi->chips[cs]; chip->spifi = spifi; diff --git a/drivers/spi/spi-hisi-sfc-v3xx.c b/drivers/spi/spi-hisi-sfc-v3xx.c index f07d1045a30a2..7cbcb065bb44c 100644 --- a/drivers/spi/spi-hisi-sfc-v3xx.c +++ b/drivers/spi/spi-hisi-sfc-v3xx.c @@ -361,7 +361,7 @@ static int hisi_sfc_v3xx_exec_op(struct spi_mem *mem, { struct hisi_sfc_v3xx_host *host; struct spi_device *spi = mem->spi; - u8 chip_select = spi->chip_select; + u8 chip_select = spi_get_chipselect(spi, 0); host = spi_controller_get_devdata(spi->master); diff --git a/drivers/spi/spi-img-spfi.c b/drivers/spi/spi-img-spfi.c index 257046f843ffd..1575e78f8b092 100644 --- a/drivers/spi/spi-img-spfi.c +++ b/drivers/spi/spi-img-spfi.c @@ -413,15 +413,15 @@ static int img_spfi_prepare(struct spi_master *master, struct spi_message *msg) val = spfi_readl(spfi, SPFI_PORT_STATE); val &= ~(SPFI_PORT_STATE_DEV_SEL_MASK << SPFI_PORT_STATE_DEV_SEL_SHIFT); - val |= msg->spi->chip_select << SPFI_PORT_STATE_DEV_SEL_SHIFT; + val |= spi_get_chipselect(msg->spi, 0) << SPFI_PORT_STATE_DEV_SEL_SHIFT; if (msg->spi->mode & SPI_CPHA) - val |= SPFI_PORT_STATE_CK_PHASE(msg->spi->chip_select); + val |= SPFI_PORT_STATE_CK_PHASE(spi_get_chipselect(msg->spi, 0)); else - val &= ~SPFI_PORT_STATE_CK_PHASE(msg->spi->chip_select); + val &= ~SPFI_PORT_STATE_CK_PHASE(spi_get_chipselect(msg->spi, 0)); if (msg->spi->mode & SPI_CPOL) - val |= SPFI_PORT_STATE_CK_POL(msg->spi->chip_select); + val |= SPFI_PORT_STATE_CK_POL(spi_get_chipselect(msg->spi, 0)); else - val &= ~SPFI_PORT_STATE_CK_POL(msg->spi->chip_select); + val &= ~SPFI_PORT_STATE_CK_POL(spi_get_chipselect(msg->spi, 0)); spfi_writel(spfi, val, SPFI_PORT_STATE); return 0; @@ -450,11 +450,11 @@ static void img_spfi_config(struct spi_master *master, struct spi_device *spi, div = DIV_ROUND_UP(clk_get_rate(spfi->spfi_clk), xfer->speed_hz); div = clamp(512 / (1 << get_count_order(div)), 1, 128); - val = spfi_readl(spfi, SPFI_DEVICE_PARAMETER(spi->chip_select)); + val = spfi_readl(spfi, SPFI_DEVICE_PARAMETER(spi_get_chipselect(spi, 0))); val &= ~(SPFI_DEVICE_PARAMETER_BITCLK_MASK << SPFI_DEVICE_PARAMETER_BITCLK_SHIFT); val |= div << SPFI_DEVICE_PARAMETER_BITCLK_SHIFT; - spfi_writel(spfi, val, SPFI_DEVICE_PARAMETER(spi->chip_select)); + spfi_writel(spfi, val, SPFI_DEVICE_PARAMETER(spi_get_chipselect(spi, 0))); spfi_writel(spfi, xfer->len << SPFI_TRANSACTION_TSIZE_SHIFT, SPFI_TRANSACTION); diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c index 6c9c87cd14cae..81221594dd972 100644 --- a/drivers/spi/spi-imx.c +++ b/drivers/spi/spi-imx.c @@ -528,7 +528,7 @@ static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx, ctrl |= MX51_ECSPI_CTRL_DRCTL(spi_imx->spi_drctl); /* set chip select to use */ - ctrl |= MX51_ECSPI_CTRL_CS(spi->chip_select); + ctrl |= MX51_ECSPI_CTRL_CS(spi_get_chipselect(spi, 0)); /* * The ctrl register must be written first, with the EN bit set other @@ -549,22 +549,22 @@ static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx, * BURST_LENGTH + 1 bits are received */ if (spi_imx->slave_mode && is_imx53_ecspi(spi_imx)) - cfg &= ~MX51_ECSPI_CONFIG_SBBCTRL(spi->chip_select); + cfg &= ~MX51_ECSPI_CONFIG_SBBCTRL(spi_get_chipselect(spi, 0)); else - cfg |= MX51_ECSPI_CONFIG_SBBCTRL(spi->chip_select); + cfg |= MX51_ECSPI_CONFIG_SBBCTRL(spi_get_chipselect(spi, 0)); if (spi->mode & SPI_CPOL) { - cfg |= MX51_ECSPI_CONFIG_SCLKPOL(spi->chip_select); - cfg |= MX51_ECSPI_CONFIG_SCLKCTL(spi->chip_select); + cfg |= MX51_ECSPI_CONFIG_SCLKPOL(spi_get_chipselect(spi, 0)); + cfg |= MX51_ECSPI_CONFIG_SCLKCTL(spi_get_chipselect(spi, 0)); } else { - cfg &= ~MX51_ECSPI_CONFIG_SCLKPOL(spi->chip_select); - cfg &= ~MX51_ECSPI_CONFIG_SCLKCTL(spi->chip_select); + cfg &= ~MX51_ECSPI_CONFIG_SCLKPOL(spi_get_chipselect(spi, 0)); + cfg &= ~MX51_ECSPI_CONFIG_SCLKCTL(spi_get_chipselect(spi, 0)); } if (spi->mode & SPI_CS_HIGH) - cfg |= MX51_ECSPI_CONFIG_SSBPOL(spi->chip_select); + cfg |= MX51_ECSPI_CONFIG_SSBPOL(spi_get_chipselect(spi, 0)); else - cfg &= ~MX51_ECSPI_CONFIG_SSBPOL(spi->chip_select); + cfg &= ~MX51_ECSPI_CONFIG_SSBPOL(spi_get_chipselect(spi, 0)); if (cfg == current_cfg) return 0; @@ -614,9 +614,9 @@ static void mx51_configure_cpha(struct spi_imx_data *spi_imx, cpha ^= flip_cpha; if (cpha) - cfg |= MX51_ECSPI_CONFIG_SCLKPHA(spi->chip_select); + cfg |= MX51_ECSPI_CONFIG_SCLKPHA(spi_get_chipselect(spi, 0)); else - cfg &= ~MX51_ECSPI_CONFIG_SCLKPHA(spi->chip_select); + cfg &= ~MX51_ECSPI_CONFIG_SCLKPHA(spi_get_chipselect(spi, 0)); writel(cfg, spi_imx->base + MX51_ECSPI_CONFIG); } @@ -768,8 +768,8 @@ static int mx31_prepare_transfer(struct spi_imx_data *spi_imx, reg |= MX31_CSPICTRL_POL; if (spi->mode & SPI_CS_HIGH) reg |= MX31_CSPICTRL_SSPOL; - if (!spi->cs_gpiod) - reg |= (spi->chip_select) << + if (!spi_get_csgpiod(spi, 0)) + reg |= (spi_get_chipselect(spi, 0)) << (is_imx35_cspi(spi_imx) ? MX35_CSPICTRL_CS_SHIFT : MX31_CSPICTRL_CS_SHIFT); @@ -868,8 +868,8 @@ static int mx21_prepare_transfer(struct spi_imx_data *spi_imx, reg |= MX21_CSPICTRL_POL; if (spi->mode & SPI_CS_HIGH) reg |= MX21_CSPICTRL_SSPOL; - if (!spi->cs_gpiod) - reg |= spi->chip_select << MX21_CSPICTRL_CS_SHIFT; + if (!spi_get_csgpiod(spi, 0)) + reg |= spi_get_chipselect(spi, 0) << MX21_CSPICTRL_CS_SHIFT; writel(reg, spi_imx->base + MXC_CSPICTRL); diff --git a/drivers/spi/spi-ingenic.c b/drivers/spi/spi-ingenic.c index 713a238bee63a..7d4b515a160d9 100644 --- a/drivers/spi/spi-ingenic.c +++ b/drivers/spi/spi-ingenic.c @@ -263,7 +263,7 @@ static int spi_ingenic_prepare_message(struct spi_controller *ctlr, { struct ingenic_spi *priv = spi_controller_get_devdata(ctlr); struct spi_device *spi = message->spi; - unsigned int cs = REG_SSICR1_FRMHL << spi->chip_select; + unsigned int cs = REG_SSICR1_FRMHL << spi_get_chipselect(spi, 0); unsigned int ssicr0_mask = REG_SSICR0_LOOP | REG_SSICR0_FSEL; unsigned int ssicr1_mask = REG_SSICR1_PHA | REG_SSICR1_POL | cs; unsigned int ssicr0 = 0, ssicr1 = 0; @@ -282,7 +282,7 @@ static int spi_ingenic_prepare_message(struct spi_controller *ctlr, if (spi->mode & SPI_LOOP) ssicr0 |= REG_SSICR0_LOOP; - if (spi->chip_select) + if (spi_get_chipselect(spi, 0)) ssicr0 |= REG_SSICR0_FSEL; if (spi->mode & SPI_CPHA) diff --git a/drivers/spi/spi-intel.c b/drivers/spi/spi-intel.c index f4679868c49f1..bc6d22149e7e1 100644 --- a/drivers/spi/spi-intel.c +++ b/drivers/spi/spi-intel.c @@ -451,7 +451,7 @@ static u32 intel_spi_chip_addr(const struct intel_spi *ispi, /* Pick up the correct start address */ if (!mem) return 0; - return mem->spi->chip_select == 1 ? ispi->chip0_size : 0; + return (spi_get_chipselect(mem->spi, 0) == 1) ? ispi->chip0_size : 0; } static int intel_spi_read_reg(struct intel_spi *ispi, const struct spi_mem *mem, diff --git a/drivers/spi/spi-jcore.c b/drivers/spi/spi-jcore.c index 74c8319c29f17..c42a3358e8c9a 100644 --- a/drivers/spi/spi-jcore.c +++ b/drivers/spi/spi-jcore.c @@ -68,9 +68,9 @@ static void jcore_spi_program(struct jcore_spi *hw) static void jcore_spi_chipsel(struct spi_device *spi, bool value) { struct jcore_spi *hw = spi_master_get_devdata(spi->master); - u32 csbit = 1U << (2 * spi->chip_select); + u32 csbit = 1U << (2 * spi_get_chipselect(spi, 0)); - dev_dbg(hw->master->dev.parent, "chipselect %d\n", spi->chip_select); + dev_dbg(hw->master->dev.parent, "chipselect %d\n", spi_get_chipselect(spi, 0)); if (value) hw->cs_reg |= csbit; diff --git a/drivers/spi/spi-lantiq-ssc.c b/drivers/spi/spi-lantiq-ssc.c index aae26f62ea87a..6b191cefb0d4f 100644 --- a/drivers/spi/spi-lantiq-ssc.c +++ b/drivers/spi/spi-lantiq-ssc.c @@ -388,11 +388,11 @@ static int lantiq_ssc_setup(struct spi_device *spidev) { struct spi_master *master = spidev->master; struct lantiq_ssc_spi *spi = spi_master_get_devdata(master); - unsigned int cs = spidev->chip_select; + unsigned int cs = spi_get_chipselect(spidev, 0); u32 gpocon; /* GPIOs are used for CS */ - if (spidev->cs_gpiod) + if (spi_get_csgpiod(spidev, 0)) return 0; dev_dbg(spi->dev, "using internal chipselect %u\n", cs); @@ -796,7 +796,7 @@ static void lantiq_ssc_handle_err(struct spi_master *master, static void lantiq_ssc_set_cs(struct spi_device *spidev, bool enable) { struct lantiq_ssc_spi *spi = spi_master_get_devdata(spidev->master); - unsigned int cs = spidev->chip_select; + unsigned int cs = spi_get_chipselect(spidev, 0); u32 fgpo; if (!!(spidev->mode & SPI_CS_HIGH) == enable) diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c index 701838b6f0c40..edd7430d4c052 100644 --- a/drivers/spi/spi-mem.c +++ b/drivers/spi/spi-mem.c @@ -325,7 +325,7 @@ int spi_mem_exec_op(struct spi_mem *mem, const struct spi_mem_op *op) if (!spi_mem_internal_supports_op(mem, op)) return -ENOTSUPP; - if (ctlr->mem_ops && ctlr->mem_ops->exec_op && !mem->spi->cs_gpiod) { + if (ctlr->mem_ops && ctlr->mem_ops->exec_op && !spi_get_csgpiod(mem->spi, 0)) { ret = spi_mem_access_start(mem); if (ret) return ret; @@ -808,7 +808,7 @@ int spi_mem_poll_status(struct spi_mem *mem, op->data.dir != SPI_MEM_DATA_IN) return -EINVAL; - if (ctlr->mem_ops && ctlr->mem_ops->poll_status && !mem->spi->cs_gpiod) { + if (ctlr->mem_ops && ctlr->mem_ops->poll_status && !spi_get_csgpiod(mem->spi, 0)) { ret = spi_mem_access_start(mem); if (ret) return ret; diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c index d47f2623a60fa..0d45cf8a2e723 100644 --- a/drivers/spi/spi-meson-spicc.c +++ b/drivers/spi/spi-meson-spicc.c @@ -505,7 +505,7 @@ static int meson_spicc_prepare_message(struct spi_master *master, conf |= FIELD_PREP(SPICC_DRCTL_MASK, SPICC_DRCTL_IGNORE); /* Select CS */ - conf |= FIELD_PREP(SPICC_CS_MASK, spi->chip_select); + conf |= FIELD_PREP(SPICC_CS_MASK, spi_get_chipselect(spi, 0)); /* Default 8bit word */ conf |= FIELD_PREP(SPICC_BITLENGTH_MASK, 8 - 1); diff --git a/drivers/spi/spi-microchip-core.c b/drivers/spi/spi-microchip-core.c index aeaa1da88f39e..1a90fcfe60151 100644 --- a/drivers/spi/spi-microchip-core.c +++ b/drivers/spi/spi-microchip-core.c @@ -247,8 +247,8 @@ static void mchp_corespi_set_cs(struct spi_device *spi, bool disable) struct mchp_corespi *corespi = spi_master_get_devdata(spi->master); reg = mchp_corespi_read(corespi, REG_SLAVE_SELECT); - reg &= ~BIT(spi->chip_select); - reg |= !disable << spi->chip_select; + reg &= ~BIT(spi_get_chipselect(spi, 0)); + reg |= !disable << spi_get_chipselect(spi, 0); mchp_corespi_write(corespi, REG_SLAVE_SELECT, reg); } @@ -265,7 +265,7 @@ static int mchp_corespi_setup(struct spi_device *spi) */ if (spi->mode & SPI_CS_HIGH) { reg = mchp_corespi_read(corespi, REG_SLAVE_SELECT); - reg |= BIT(spi->chip_select); + reg |= BIT(spi_get_chipselect(spi, 0)); mchp_corespi_write(corespi, REG_SLAVE_SELECT, reg); } return 0; diff --git a/drivers/spi/spi-mpc512x-psc.c b/drivers/spi/spi-mpc512x-psc.c index 0b4d49ef84de8..1e7d081c141ae 100644 --- a/drivers/spi/spi-mpc512x-psc.c +++ b/drivers/spi/spi-mpc512x-psc.c @@ -124,17 +124,17 @@ static void mpc512x_psc_spi_activate_cs(struct spi_device *spi) out_be32(psc_addr(mps, ccr), ccr); mps->bits_per_word = cs->bits_per_word; - if (spi->cs_gpiod) { + if (spi_get_csgpiod(spi, 0)) { /* gpiolib will deal with the inversion */ - gpiod_set_value(spi->cs_gpiod, 1); + gpiod_set_value(spi_get_csgpiod(spi, 0), 1); } } static void mpc512x_psc_spi_deactivate_cs(struct spi_device *spi) { - if (spi->cs_gpiod) { + if (spi_get_csgpiod(spi, 0)) { /* gpiolib will deal with the inversion */ - gpiod_set_value(spi->cs_gpiod, 0); + gpiod_set_value(spi_get_csgpiod(spi, 0), 0); } } diff --git a/drivers/spi/spi-mpc52xx.c b/drivers/spi/spi-mpc52xx.c index 7b64e64c65cfe..c474a767fc484 100644 --- a/drivers/spi/spi-mpc52xx.c +++ b/drivers/spi/spi-mpc52xx.c @@ -101,7 +101,7 @@ static void mpc52xx_spi_chipsel(struct mpc52xx_spi *ms, int value) int cs; if (ms->gpio_cs_count > 0) { - cs = ms->message->spi->chip_select; + cs = spi_get_chipselect(ms->message->spi, 0); gpiod_set_value(ms->gpio_cs[cs], value); } else { out_8(ms->regs + SPI_PORTDATA, value ? 0 : 0x08); diff --git a/drivers/spi/spi-mt65xx.c b/drivers/spi/spi-mt65xx.c index 9eab6c20dbc56..21c321f437667 100644 --- a/drivers/spi/spi-mt65xx.c +++ b/drivers/spi/spi-mt65xx.c @@ -421,7 +421,7 @@ static int mtk_spi_hw_init(struct spi_master *master, /* pad select */ if (mdata->dev_comp->need_pad_sel) - writel(mdata->pad_sel[spi->chip_select], + writel(mdata->pad_sel[spi_get_chipselect(spi, 0)], mdata->base + SPI_PAD_SEL_REG); /* tick delay */ @@ -735,9 +735,9 @@ static int mtk_spi_setup(struct spi_device *spi) if (!spi->controller_data) spi->controller_data = (void *)&mtk_default_chip_info; - if (mdata->dev_comp->need_pad_sel && spi->cs_gpiod) + if (mdata->dev_comp->need_pad_sel && spi_get_csgpiod(spi, 0)) /* CS de-asserted, gpiolib will handle inversion */ - gpiod_direction_output(spi->cs_gpiod, 0); + gpiod_direction_output(spi_get_csgpiod(spi, 0), 0); return 0; } diff --git a/drivers/spi/spi-mt7621.c b/drivers/spi/spi-mt7621.c index c4cc8e2f85e2f..3e9d396b33bd3 100644 --- a/drivers/spi/spi-mt7621.c +++ b/drivers/spi/spi-mt7621.c @@ -76,7 +76,7 @@ static inline void mt7621_spi_write(struct mt7621_spi *rs, u32 reg, u32 val) static void mt7621_spi_set_cs(struct spi_device *spi, int enable) { struct mt7621_spi *rs = spidev_to_mt7621_spi(spi); - int cs = spi->chip_select; + int cs = spi_get_chipselect(spi, 0); u32 polar = 0; u32 master; diff --git a/drivers/spi/spi-mux.c b/drivers/spi/spi-mux.c index 0709e987bd5ab..fa8c1f740c702 100644 --- a/drivers/spi/spi-mux.c +++ b/drivers/spi/spi-mux.c @@ -51,22 +51,22 @@ static int spi_mux_select(struct spi_device *spi) struct spi_mux_priv *priv = spi_controller_get_devdata(spi->controller); int ret; - ret = mux_control_select(priv->mux, spi->chip_select); + ret = mux_control_select(priv->mux, spi_get_chipselect(spi, 0)); if (ret) return ret; - if (priv->current_cs == spi->chip_select) + if (priv->current_cs == spi_get_chipselect(spi, 0)) return 0; dev_dbg(&priv->spi->dev, "setting up the mux for cs %d\n", - spi->chip_select); + spi_get_chipselect(spi, 0)); /* copy the child device's settings except for the cs */ priv->spi->max_speed_hz = spi->max_speed_hz; priv->spi->mode = spi->mode; priv->spi->bits_per_word = spi->bits_per_word; - priv->current_cs = spi->chip_select; + priv->current_cs = spi_get_chipselect(spi, 0); return 0; } diff --git a/drivers/spi/spi-mxic.c b/drivers/spi/spi-mxic.c index a3dba17390eba..52bd2c49c34e2 100644 --- a/drivers/spi/spi-mxic.c +++ b/drivers/spi/spi-mxic.c @@ -306,8 +306,8 @@ static u32 mxic_spi_prep_hc_cfg(struct spi_device *spi, u32 flags) nio = 2; return flags | HC_CFG_NIO(nio) | - HC_CFG_TYPE(spi->chip_select, HC_CFG_TYPE_SPI_NOR) | - HC_CFG_SLV_ACT(spi->chip_select) | HC_CFG_IDLE_SIO_LVL(1); + HC_CFG_TYPE(spi_get_chipselect(spi, 0), HC_CFG_TYPE_SPI_NOR) | + HC_CFG_SLV_ACT(spi_get_chipselect(spi, 0)) | HC_CFG_IDLE_SIO_LVL(1); } static u32 mxic_spi_mem_prep_op_cfg(const struct spi_mem_op *op, @@ -405,7 +405,7 @@ static ssize_t mxic_spi_mem_dirmap_read(struct spi_mem_dirmap_desc *desc, len = min_t(size_t, len, mxic->linear.size); writel(len, mxic->regs + LRD_RANGE); writel(LMODE_CMD0(desc->info.op_tmpl.cmd.opcode) | - LMODE_SLV_ACT(desc->mem->spi->chip_select) | + LMODE_SLV_ACT(spi_get_chipselect(desc->mem->spi, 0)) | LMODE_EN, mxic->regs + LRD_CTRL); @@ -449,7 +449,7 @@ static ssize_t mxic_spi_mem_dirmap_write(struct spi_mem_dirmap_desc *desc, len = min_t(size_t, len, mxic->linear.size); writel(len, mxic->regs + LWR_RANGE); writel(LMODE_CMD0(desc->info.op_tmpl.cmd.opcode) | - LMODE_SLV_ACT(desc->mem->spi->chip_select) | + LMODE_SLV_ACT(spi_get_chipselect(desc->mem->spi, 0)) | LMODE_EN, mxic->regs + LWR_CTRL); @@ -524,7 +524,7 @@ static int mxic_spi_mem_exec_op(struct spi_mem *mem, writel(HC_EN_BIT, mxic->regs + HC_EN); writel(mxic_spi_mem_prep_op_cfg(op, op->data.nbytes), - mxic->regs + SS_CTRL(mem->spi->chip_select)); + mxic->regs + SS_CTRL(spi_get_chipselect(mem->spi, 0))); writel(readl(mxic->regs + HC_CFG) | HC_CFG_MAN_CS_ASSERT, mxic->regs + HC_CFG); diff --git a/drivers/spi/spi-mxs.c b/drivers/spi/spi-mxs.c index 55178579f3c6f..98076aa4b1c7e 100644 --- a/drivers/spi/spi-mxs.c +++ b/drivers/spi/spi-mxs.c @@ -369,7 +369,7 @@ static int mxs_spi_transfer_one(struct spi_master *master, /* Program CS register bits here, it will be used for all transfers. */ writel(BM_SSP_CTRL0_WAIT_FOR_CMD | BM_SSP_CTRL0_WAIT_FOR_IRQ, ssp->base + HW_SSP_CTRL0 + STMP_OFFSET_REG_CLR); - writel(mxs_spi_cs_to_reg(m->spi->chip_select), + writel(mxs_spi_cs_to_reg(spi_get_chipselect(m->spi, 0)), ssp->base + HW_SSP_CTRL0 + STMP_OFFSET_REG_SET); list_for_each_entry(t, &m->transfers, transfer_list) { diff --git a/drivers/spi/spi-npcm-fiu.c b/drivers/spi/spi-npcm-fiu.c index 559d3a5b4062c..86e3978883fef 100644 --- a/drivers/spi/spi-npcm-fiu.c +++ b/drivers/spi/spi-npcm-fiu.c @@ -288,7 +288,7 @@ static ssize_t npcm_fiu_direct_read(struct spi_mem_dirmap_desc *desc, { struct npcm_fiu_spi *fiu = spi_controller_get_devdata(desc->mem->spi->master); - struct npcm_fiu_chip *chip = &fiu->chip[desc->mem->spi->chip_select]; + struct npcm_fiu_chip *chip = &fiu->chip[spi_get_chipselect(desc->mem->spi, 0)]; void __iomem *src = (void __iomem *)(chip->flash_region_mapped_ptr + offs); u8 *buf_rx = buf; @@ -315,7 +315,7 @@ static ssize_t npcm_fiu_direct_write(struct spi_mem_dirmap_desc *desc, { struct npcm_fiu_spi *fiu = spi_controller_get_devdata(desc->mem->spi->master); - struct npcm_fiu_chip *chip = &fiu->chip[desc->mem->spi->chip_select]; + struct npcm_fiu_chip *chip = &fiu->chip[spi_get_chipselect(desc->mem->spi, 0)]; void __iomem *dst = (void __iomem *)(chip->flash_region_mapped_ptr + offs); const u8 *buf_tx = buf; @@ -344,7 +344,7 @@ static int npcm_fiu_uma_read(struct spi_mem *mem, regmap_update_bits(fiu->regmap, NPCM_FIU_UMA_CTS, NPCM_FIU_UMA_CTS_DEV_NUM, - (mem->spi->chip_select << + (spi_get_chipselect(mem->spi, 0) << NPCM_FIU_UMA_CTS_DEV_NUM_SHIFT)); regmap_update_bits(fiu->regmap, NPCM_FIU_UMA_CMD, NPCM_FIU_UMA_CMD_CMD, op->cmd.opcode); @@ -398,7 +398,7 @@ static int npcm_fiu_uma_write(struct spi_mem *mem, regmap_update_bits(fiu->regmap, NPCM_FIU_UMA_CTS, NPCM_FIU_UMA_CTS_DEV_NUM, - (mem->spi->chip_select << + (spi_get_chipselect(mem->spi, 0) << NPCM_FIU_UMA_CTS_DEV_NUM_SHIFT)); regmap_update_bits(fiu->regmap, NPCM_FIU_UMA_CMD, @@ -451,7 +451,7 @@ static int npcm_fiu_manualwrite(struct spi_mem *mem, regmap_update_bits(fiu->regmap, NPCM_FIU_UMA_CTS, NPCM_FIU_UMA_CTS_DEV_NUM, - (mem->spi->chip_select << + (spi_get_chipselect(mem->spi, 0) << NPCM_FIU_UMA_CTS_DEV_NUM_SHIFT)); regmap_update_bits(fiu->regmap, NPCM_FIU_UMA_CTS, NPCM_FIU_UMA_CTS_SW_CS, 0); @@ -545,7 +545,7 @@ static int npcm_fiu_exec_op(struct spi_mem *mem, const struct spi_mem_op *op) { struct npcm_fiu_spi *fiu = spi_controller_get_devdata(mem->spi->master); - struct npcm_fiu_chip *chip = &fiu->chip[mem->spi->chip_select]; + struct npcm_fiu_chip *chip = &fiu->chip[spi_get_chipselect(mem->spi, 0)]; int ret = 0; u8 *buf; @@ -605,7 +605,7 @@ static int npcm_fiu_dirmap_create(struct spi_mem_dirmap_desc *desc) { struct npcm_fiu_spi *fiu = spi_controller_get_devdata(desc->mem->spi->master); - struct npcm_fiu_chip *chip = &fiu->chip[desc->mem->spi->chip_select]; + struct npcm_fiu_chip *chip = &fiu->chip[spi_get_chipselect(desc->mem->spi, 0)]; struct regmap *gcr_regmap; if (!fiu->res_mem) { @@ -624,7 +624,7 @@ static int npcm_fiu_dirmap_create(struct spi_mem_dirmap_desc *desc) chip->flash_region_mapped_ptr = devm_ioremap(fiu->dev, (fiu->res_mem->start + (fiu->info->max_map_size * - desc->mem->spi->chip_select)), + spi_get_chipselect(desc->mem->spi, 0))), (u32)desc->info.length); if (!chip->flash_region_mapped_ptr) { dev_warn(fiu->dev, "Error mapping memory region, direct read disabled\n"); @@ -669,9 +669,9 @@ static int npcm_fiu_setup(struct spi_device *spi) struct npcm_fiu_spi *fiu = spi_controller_get_devdata(ctrl); struct npcm_fiu_chip *chip; - chip = &fiu->chip[spi->chip_select]; + chip = &fiu->chip[spi_get_chipselect(spi, 0)]; chip->fiu = fiu; - chip->chipselect = spi->chip_select; + chip->chipselect = spi_get_chipselect(spi, 0); chip->clkrate = spi->max_speed_hz; fiu->clkrate = clk_get_rate(fiu->clk); diff --git a/drivers/spi/spi-nxp-fspi.c b/drivers/spi/spi-nxp-fspi.c index 1c1991a26c153..e9baf93aef7e1 100644 --- a/drivers/spi/spi-nxp-fspi.c +++ b/drivers/spi/spi-nxp-fspi.c @@ -663,7 +663,7 @@ static void nxp_fspi_select_mem(struct nxp_fspi *f, struct spi_device *spi) * Return, if previously selected slave device is same as current * requested slave device. */ - if (f->selected == spi->chip_select) + if (f->selected == spi_get_chipselect(spi, 0)) return; /* Reset FLSHxxCR0 registers */ @@ -676,9 +676,9 @@ static void nxp_fspi_select_mem(struct nxp_fspi *f, struct spi_device *spi) size_kb = FSPI_FLSHXCR0_SZ(f->memmap_phy_size); fspi_writel(f, size_kb, f->iobase + FSPI_FLSHA1CR0 + - 4 * spi->chip_select); + 4 * spi_get_chipselect(spi, 0)); - dev_dbg(f->dev, "Slave device [CS:%x] selected\n", spi->chip_select); + dev_dbg(f->dev, "Slave device [CS:%x] selected\n", spi_get_chipselect(spi, 0)); nxp_fspi_clk_disable_unprep(f); @@ -690,7 +690,7 @@ static void nxp_fspi_select_mem(struct nxp_fspi *f, struct spi_device *spi) if (ret) return; - f->selected = spi->chip_select; + f->selected = spi_get_chipselect(spi, 0); } static int nxp_fspi_read_ahb(struct nxp_fspi *f, const struct spi_mem_op *op) @@ -1055,7 +1055,7 @@ static const char *nxp_fspi_get_name(struct spi_mem *mem) name = devm_kasprintf(dev, GFP_KERNEL, "%s-%d", dev_name(f->dev), - mem->spi->chip_select); + spi_get_chipselect(mem->spi, 0)); if (!name) { dev_err(dev, "failed to get memory for custom flash name\n"); diff --git a/drivers/spi/spi-omap-uwire.c b/drivers/spi/spi-omap-uwire.c index 20c87163d612e..5b3a5e654ddd4 100644 --- a/drivers/spi/spi-omap-uwire.c +++ b/drivers/spi/spi-omap-uwire.c @@ -179,7 +179,7 @@ static void uwire_chipselect(struct spi_device *spi, int value) w = uwire_read_reg(UWIRE_CSR); old_cs = (w >> 10) & 0x03; - if (value == BITBANG_CS_INACTIVE || old_cs != spi->chip_select) { + if (value == BITBANG_CS_INACTIVE || old_cs != spi_get_chipselect(spi, 0)) { /* Deselect this CS, or the previous CS */ w &= ~CS_CMD; uwire_write_reg(UWIRE_CSR, w); @@ -193,7 +193,7 @@ static void uwire_chipselect(struct spi_device *spi, int value) else uwire_write_reg(UWIRE_SR4, 0); - w = spi->chip_select << 10; + w = spi_get_chipselect(spi, 0) << 10; w |= CS_CMD; uwire_write_reg(UWIRE_CSR, w); } @@ -210,7 +210,7 @@ static int uwire_txrx(struct spi_device *spi, struct spi_transfer *t) if (!t->tx_buf && !t->rx_buf) return 0; - w = spi->chip_select << 10; + w = spi_get_chipselect(spi, 0) << 10; w |= CS_CMD; if (t->tx_buf) { @@ -408,7 +408,7 @@ static int uwire_setup_transfer(struct spi_device *spi, struct spi_transfer *t) rate /= 8; break; } - omap_uwire_configure_mode(spi->chip_select, flags); + omap_uwire_configure_mode(spi_get_chipselect(spi, 0), flags); pr_debug("%s: uwire flags %02x, armxor %lu KHz, SCK %lu KHz\n", __func__, flags, clk_get_rate(uwire->ck) / 1000, diff --git a/drivers/spi/spi-omap2-mcspi.c b/drivers/spi/spi-omap2-mcspi.c index 6ba9b0d7710b0..5e404da112a2f 100644 --- a/drivers/spi/spi-omap2-mcspi.c +++ b/drivers/spi/spi-omap2-mcspi.c @@ -379,7 +379,7 @@ static void omap2_mcspi_rx_callback(void *data) { struct spi_device *spi = data; struct omap2_mcspi *mcspi = spi_master_get_devdata(spi->master); - struct omap2_mcspi_dma *mcspi_dma = &mcspi->dma_channels[spi->chip_select]; + struct omap2_mcspi_dma *mcspi_dma = &mcspi->dma_channels[spi_get_chipselect(spi, 0)]; /* We must disable the DMA RX request */ omap2_mcspi_set_dma_req(spi, 1, 0); @@ -391,7 +391,7 @@ static void omap2_mcspi_tx_callback(void *data) { struct spi_device *spi = data; struct omap2_mcspi *mcspi = spi_master_get_devdata(spi->master); - struct omap2_mcspi_dma *mcspi_dma = &mcspi->dma_channels[spi->chip_select]; + struct omap2_mcspi_dma *mcspi_dma = &mcspi->dma_channels[spi_get_chipselect(spi, 0)]; /* We must disable the DMA TX request */ omap2_mcspi_set_dma_req(spi, 0, 0); @@ -408,7 +408,7 @@ static void omap2_mcspi_tx_dma(struct spi_device *spi, struct dma_async_tx_descriptor *tx; mcspi = spi_master_get_devdata(spi->master); - mcspi_dma = &mcspi->dma_channels[spi->chip_select]; + mcspi_dma = &mcspi->dma_channels[spi_get_chipselect(spi, 0)]; dmaengine_slave_config(mcspi_dma->dma_tx, &cfg); @@ -446,7 +446,7 @@ omap2_mcspi_rx_dma(struct spi_device *spi, struct spi_transfer *xfer, struct dma_async_tx_descriptor *tx; mcspi = spi_master_get_devdata(spi->master); - mcspi_dma = &mcspi->dma_channels[spi->chip_select]; + mcspi_dma = &mcspi->dma_channels[spi_get_chipselect(spi, 0)]; count = xfer->len; /* @@ -591,7 +591,7 @@ omap2_mcspi_txrx_dma(struct spi_device *spi, struct spi_transfer *xfer) int wait_res; mcspi = spi_master_get_devdata(spi->master); - mcspi_dma = &mcspi->dma_channels[spi->chip_select]; + mcspi_dma = &mcspi->dma_channels[spi_get_chipselect(spi, 0)]; if (cs->word_len <= 8) { width = DMA_SLAVE_BUSWIDTH_1_BYTE; @@ -1062,8 +1062,8 @@ static int omap2_mcspi_setup(struct spi_device *spi) cs = kzalloc(sizeof(*cs), GFP_KERNEL); if (!cs) return -ENOMEM; - cs->base = mcspi->base + spi->chip_select * 0x14; - cs->phys = mcspi->phys + spi->chip_select * 0x14; + cs->base = mcspi->base + spi_get_chipselect(spi, 0) * 0x14; + cs->phys = mcspi->phys + spi_get_chipselect(spi, 0) * 0x14; cs->mode = 0; cs->chconf0 = 0; cs->chctrl0 = 0; @@ -1142,7 +1142,7 @@ static int omap2_mcspi_transfer_one(struct spi_master *master, u32 chconf; mcspi = spi_master_get_devdata(master); - mcspi_dma = mcspi->dma_channels + spi->chip_select; + mcspi_dma = mcspi->dma_channels + spi_get_chipselect(spi, 0); cs = spi->controller_state; cd = spi->controller_data; @@ -1158,7 +1158,7 @@ static int omap2_mcspi_transfer_one(struct spi_master *master, omap2_mcspi_set_enable(spi, 0); - if (spi->cs_gpiod) + if (spi_get_csgpiod(spi, 0)) omap2_mcspi_set_cs(spi, spi->mode & SPI_CS_HIGH); if (par_override || @@ -1247,7 +1247,7 @@ static int omap2_mcspi_transfer_one(struct spi_master *master, omap2_mcspi_set_enable(spi, 0); - if (spi->cs_gpiod) + if (spi_get_csgpiod(spi, 0)) omap2_mcspi_set_cs(spi, !(spi->mode & SPI_CS_HIGH)); if (mcspi->fifo_depth > 0 && t) @@ -1289,7 +1289,7 @@ static bool omap2_mcspi_can_dma(struct spi_master *master, { struct omap2_mcspi *mcspi = spi_master_get_devdata(spi->master); struct omap2_mcspi_dma *mcspi_dma = - &mcspi->dma_channels[spi->chip_select]; + &mcspi->dma_channels[spi_get_chipselect(spi, 0)]; if (!mcspi_dma->dma_rx || !mcspi_dma->dma_tx) return false; @@ -1307,7 +1307,7 @@ static size_t omap2_mcspi_max_xfer_size(struct spi_device *spi) { struct omap2_mcspi *mcspi = spi_master_get_devdata(spi->master); struct omap2_mcspi_dma *mcspi_dma = - &mcspi->dma_channels[spi->chip_select]; + &mcspi->dma_channels[spi_get_chipselect(spi, 0)]; if (mcspi->max_xfer_len && mcspi_dma->dma_rx) return mcspi->max_xfer_len; diff --git a/drivers/spi/spi-orion.c b/drivers/spi/spi-orion.c index 565cd4c48d7bd..13e60976692cc 100644 --- a/drivers/spi/spi-orion.c +++ b/drivers/spi/spi-orion.c @@ -346,7 +346,7 @@ static void orion_spi_set_cs(struct spi_device *spi, bool enable) * as it is handled by a GPIO, but that doesn't matter. What we need * is to deassert the old chip select and assert some other chip select. */ - val |= ORION_SPI_CS(spi->chip_select); + val |= ORION_SPI_CS(spi_get_chipselect(spi, 0)); /* * Chip select logic is inverted from spi_set_cs(). For lines using a @@ -470,7 +470,7 @@ orion_spi_write_read(struct spi_device *spi, struct spi_transfer *xfer) unsigned int count; int word_len; struct orion_spi *orion_spi; - int cs = spi->chip_select; + int cs = spi_get_chipselect(spi, 0); void __iomem *vaddr; word_len = spi->bits_per_word; diff --git a/drivers/spi/spi-pci1xxxx.c b/drivers/spi/spi-pci1xxxx.c index 13efbfeff92ce..82d4bfeea1fa4 100644 --- a/drivers/spi/spi-pci1xxxx.c +++ b/drivers/spi/spi-pci1xxxx.c @@ -116,11 +116,11 @@ static void pci1xxxx_spi_set_cs(struct spi_device *spi, bool enable) regval = readl(par->reg_base + SPI_MST_CTL_REG_OFFSET(p->hw_inst)); if (enable) { regval &= ~SPI_MST_CTL_DEVSEL_MASK; - regval |= (spi->chip_select << 25); + regval |= (spi_get_chipselect(spi, 0) << 25); writel(regval, par->reg_base + SPI_MST_CTL_REG_OFFSET(p->hw_inst)); } else { - regval &= ~(spi->chip_select << 25); + regval &= ~(spi_get_chipselect(spi, 0) << 25); writel(regval, par->reg_base + SPI_MST_CTL_REG_OFFSET(p->hw_inst)); diff --git a/drivers/spi/spi-pic32-sqi.c b/drivers/spi/spi-pic32-sqi.c index 86ad17597f5fd..ed02d17897d19 100644 --- a/drivers/spi/spi-pic32-sqi.c +++ b/drivers/spi/spi-pic32-sqi.c @@ -267,7 +267,7 @@ static int pic32_sqi_one_transfer(struct pic32_sqi *sqi, u32 nbits; /* Device selection */ - bd_ctrl = spi->chip_select << BD_DEVSEL_SHIFT; + bd_ctrl = spi_get_chipselect(spi, 0) << BD_DEVSEL_SHIFT; /* half-duplex: select transfer buffer, direction and lane */ if (xfer->rx_buf) { diff --git a/drivers/spi/spi-pic32.c b/drivers/spi/spi-pic32.c index 7e5c09a7d4890..387673694f911 100644 --- a/drivers/spi/spi-pic32.c +++ b/drivers/spi/spi-pic32.c @@ -591,7 +591,7 @@ static int pic32_spi_setup(struct spi_device *spi) * unreliable/erroneous SPI transactions. * To avoid that we will always handle /CS by toggling GPIO. */ - if (!spi->cs_gpiod) + if (!spi_get_csgpiod(spi, 0)) return -EINVAL; return 0; @@ -600,7 +600,7 @@ static int pic32_spi_setup(struct spi_device *spi) static void pic32_spi_cleanup(struct spi_device *spi) { /* de-activate cs-gpio, gpiolib will handle inversion */ - gpiod_direction_output(spi->cs_gpiod, 0); + gpiod_direction_output(spi_get_csgpiod(spi, 0), 0); } static int pic32_spi_dma_prep(struct pic32_spi *pic32s, struct device *dev) diff --git a/drivers/spi/spi-pl022.c b/drivers/spi/spi-pl022.c index a17ff839117f9..982407bc5d9f9 100644 --- a/drivers/spi/spi-pl022.c +++ b/drivers/spi/spi-pl022.c @@ -1587,9 +1587,9 @@ static int pl022_transfer_one_message(struct spi_master *master, /* Setup the SPI using the per chip configuration */ pl022->cur_chip = spi_get_ctldata(msg->spi); - pl022->cur_cs = msg->spi->chip_select; + pl022->cur_cs = spi_get_chipselect(msg->spi, 0); /* This is always available but may be set to -ENOENT */ - pl022->cur_gpiod = msg->spi->cs_gpiod; + pl022->cur_gpiod = spi_get_csgpiod(msg->spi, 0); restore_state(pl022); flush(pl022); diff --git a/drivers/spi/spi-pxa2xx.c b/drivers/spi/spi-pxa2xx.c index 32cc82a89ec1e..abcdc1eb1a40f 100644 --- a/drivers/spi/spi-pxa2xx.c +++ b/drivers/spi/spi-pxa2xx.c @@ -368,7 +368,7 @@ static void lpss_ssp_select_cs(struct spi_device *spi, value = __lpss_ssp_read_priv(drv_data, config->reg_cs_ctrl); - cs = spi->chip_select; + cs = spi_get_chipselect(spi, 0); cs <<= config->cs_sel_shift; if (cs != (value & config->cs_sel_mask)) { /* @@ -429,7 +429,7 @@ static void cs_assert(struct spi_device *spi) spi_controller_get_devdata(spi->controller); if (drv_data->ssp_type == CE4100_SSP) { - pxa2xx_spi_write(drv_data, SSSR, spi->chip_select); + pxa2xx_spi_write(drv_data, SSSR, spi_get_chipselect(spi, 0)); return; } @@ -1217,7 +1217,7 @@ static int setup(struct spi_device *spi) return -ENOMEM; if (drv_data->ssp_type == CE4100_SSP) { - if (spi->chip_select > 4) { + if (spi_get_chipselect(spi, 0) > 4) { dev_err(&spi->dev, "failed setup: cs number must not be > 4.\n"); kfree(chip); diff --git a/drivers/spi/spi-qcom-qspi.c b/drivers/spi/spi-qcom-qspi.c index c334dfec4117a..33c056fd5f4b7 100644 --- a/drivers/spi/spi-qcom-qspi.c +++ b/drivers/spi/spi-qcom-qspi.c @@ -311,7 +311,7 @@ static int qcom_qspi_prepare_message(struct spi_master *master, mstr_cfg = readl(ctrl->base + MSTR_CONFIG); mstr_cfg &= ~CHIP_SELECT_NUM; - if (message->spi->chip_select) + if (spi_get_chipselect(message->spi, 0)) mstr_cfg |= CHIP_SELECT_NUM; mstr_cfg |= FB_CLK_EN | PIN_WPN | PIN_HOLDN | SBL_EN | FULL_CYCLE_MODE; diff --git a/drivers/spi/spi-rb4xx.c b/drivers/spi/spi-rb4xx.c index 9f97d18a05c10..3c79a5d85ac26 100644 --- a/drivers/spi/spi-rb4xx.c +++ b/drivers/spi/spi-rb4xx.c @@ -107,7 +107,7 @@ static int rb4xx_transfer_one(struct spi_master *master, * command set was designed to almost not clash with that of the * boot flash. */ - if (spi->chip_select == 2) + if (spi_get_chipselect(spi, 0) == 2) /* MMC */ spi_ioc = AR71XX_SPI_IOC_CS0; else diff --git a/drivers/spi/spi-rockchip-sfc.c b/drivers/spi/spi-rockchip-sfc.c index 69347b6bf60cd..ce658295579a4 100644 --- a/drivers/spi/spi-rockchip-sfc.c +++ b/drivers/spi/spi-rockchip-sfc.c @@ -346,7 +346,7 @@ static int rockchip_sfc_xfer_setup(struct rockchip_sfc *sfc, /* set the Controller */ ctrl |= SFC_CTRL_PHASE_SEL_NEGETIVE; - cmd |= mem->spi->chip_select << SFC_CMD_CS_SHIFT; + cmd |= spi_get_chipselect(mem->spi, 0) << SFC_CMD_CS_SHIFT; dev_dbg(sfc->dev, "sfc addr.nbytes=%x(x%d) dummy.nbytes=%x(x%d)\n", op->addr.nbytes, op->addr.buswidth, diff --git a/drivers/spi/spi-rockchip.c b/drivers/spi/spi-rockchip.c index 79242dc5272de..adc5638eff4ba 100644 --- a/drivers/spi/spi-rockchip.c +++ b/drivers/spi/spi-rockchip.c @@ -246,28 +246,30 @@ static void rockchip_spi_set_cs(struct spi_device *spi, bool enable) bool cs_asserted = spi->mode & SPI_CS_HIGH ? enable : !enable; /* Return immediately for no-op */ - if (cs_asserted == rs->cs_asserted[spi->chip_select]) + if (cs_asserted == rs->cs_asserted[spi_get_chipselect(spi, 0)]) return; if (cs_asserted) { /* Keep things powered as long as CS is asserted */ pm_runtime_get_sync(rs->dev); - if (spi->cs_gpiod) + if (spi_get_csgpiod(spi, 0)) ROCKCHIP_SPI_SET_BITS(rs->regs + ROCKCHIP_SPI_SER, 1); else - ROCKCHIP_SPI_SET_BITS(rs->regs + ROCKCHIP_SPI_SER, BIT(spi->chip_select)); + ROCKCHIP_SPI_SET_BITS(rs->regs + ROCKCHIP_SPI_SER, + BIT(spi_get_chipselect(spi, 0))); } else { - if (spi->cs_gpiod) + if (spi_get_csgpiod(spi, 0)) ROCKCHIP_SPI_CLR_BITS(rs->regs + ROCKCHIP_SPI_SER, 1); else - ROCKCHIP_SPI_CLR_BITS(rs->regs + ROCKCHIP_SPI_SER, BIT(spi->chip_select)); + ROCKCHIP_SPI_CLR_BITS(rs->regs + ROCKCHIP_SPI_SER, + BIT(spi_get_chipselect(spi, 0))); /* Drop reference from when we first asserted CS */ pm_runtime_put(rs->dev); } - rs->cs_asserted[spi->chip_select] = cs_asserted; + rs->cs_asserted[spi_get_chipselect(spi, 0)] = cs_asserted; } static void rockchip_spi_handle_err(struct spi_controller *ctlr, @@ -541,7 +543,7 @@ static int rockchip_spi_config(struct rockchip_spi *rs, if (spi->mode & SPI_LSB_FIRST) cr0 |= CR0_FBM_LSB << CR0_FBM_OFFSET; if (spi->mode & SPI_CS_HIGH) - cr0 |= BIT(spi->chip_select) << CR0_SOI_OFFSET; + cr0 |= BIT(spi_get_chipselect(spi, 0)) << CR0_SOI_OFFSET; if (xfer->rx_buf && xfer->tx_buf) cr0 |= CR0_XFM_TR << CR0_XFM_OFFSET; @@ -724,7 +726,7 @@ static int rockchip_spi_setup(struct spi_device *spi) struct rockchip_spi *rs = spi_controller_get_devdata(spi->controller); u32 cr0; - if (!spi->cs_gpiod && (spi->mode & SPI_CS_HIGH) && !rs->cs_high_supported) { + if (!spi_get_csgpiod(spi, 0) && (spi->mode & SPI_CS_HIGH) && !rs->cs_high_supported) { dev_warn(&spi->dev, "setup: non GPIO CS can't be active-high\n"); return -EINVAL; } @@ -735,10 +737,10 @@ static int rockchip_spi_setup(struct spi_device *spi) cr0 &= ~(0x3 << CR0_SCPH_OFFSET); cr0 |= ((spi->mode & 0x3) << CR0_SCPH_OFFSET); - if (spi->mode & SPI_CS_HIGH && spi->chip_select <= 1) - cr0 |= BIT(spi->chip_select) << CR0_SOI_OFFSET; - else if (spi->chip_select <= 1) - cr0 &= ~(BIT(spi->chip_select) << CR0_SOI_OFFSET); + if (spi->mode & SPI_CS_HIGH && spi_get_chipselect(spi, 0) <= 1) + cr0 |= BIT(spi_get_chipselect(spi, 0)) << CR0_SOI_OFFSET; + else if (spi_get_chipselect(spi, 0) <= 1) + cr0 &= ~(BIT(spi_get_chipselect(spi, 0)) << CR0_SOI_OFFSET); writel_relaxed(cr0, rs->regs + ROCKCHIP_SPI_CTRLR0); diff --git a/drivers/spi/spi-rspi.c b/drivers/spi/spi-rspi.c index 411b1307b7fd8..4d4b98f8eb80f 100644 --- a/drivers/spi/spi-rspi.c +++ b/drivers/spi/spi-rspi.c @@ -950,7 +950,7 @@ static int rspi_setup(struct spi_device *spi) struct rspi_data *rspi = spi_controller_get_devdata(spi->controller); u8 sslp; - if (spi->cs_gpiod) + if (spi_get_csgpiod(spi, 0)) return 0; pm_runtime_get_sync(&rspi->pdev->dev); @@ -958,9 +958,9 @@ static int rspi_setup(struct spi_device *spi) sslp = rspi_read8(rspi, RSPI_SSLP); if (spi->mode & SPI_CS_HIGH) - sslp |= SSLP_SSLP(spi->chip_select); + sslp |= SSLP_SSLP(spi_get_chipselect(spi, 0)); else - sslp &= ~SSLP_SSLP(spi->chip_select); + sslp &= ~SSLP_SSLP(spi_get_chipselect(spi, 0)); rspi_write8(rspi, sslp, RSPI_SSLP); spin_unlock_irq(&rspi->lock); @@ -1001,8 +1001,8 @@ static int rspi_prepare_message(struct spi_controller *ctlr, rspi->spcmd |= SPCMD_LSBF; /* Configure slave signal to assert */ - rspi->spcmd |= SPCMD_SSLA(spi->cs_gpiod ? rspi->ctlr->unused_native_cs - : spi->chip_select); + rspi->spcmd |= SPCMD_SSLA(spi_get_csgpiod(spi, 0) ? rspi->ctlr->unused_native_cs + : spi_get_chipselect(spi, 0)); /* CMOS output mode and MOSI signal from previous transfer */ rspi->sppcr = 0; diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c index 71d324ec9a70a..f6682bfe484c2 100644 --- a/drivers/spi/spi-s3c64xx.c +++ b/drivers/spi/spi-s3c64xx.c @@ -891,7 +891,7 @@ static int s3c64xx_spi_setup(struct spi_device *spi) /* NULL is fine, we just avoid using the FB delay (=0) */ if (IS_ERR(cs)) { - dev_err(&spi->dev, "No CS for SPI(%d)\n", spi->chip_select); + dev_err(&spi->dev, "No CS for SPI(%d)\n", spi_get_chipselect(spi, 0)); return -ENODEV; } diff --git a/drivers/spi/spi-sc18is602.c b/drivers/spi/spi-sc18is602.c index 983b3621bc2ad..a12adc68731b3 100644 --- a/drivers/spi/spi-sc18is602.c +++ b/drivers/spi/spi-sc18is602.c @@ -70,7 +70,7 @@ static int sc18is602_txrx(struct sc18is602 *hw, struct spi_message *msg, if (hw->tlen == 0) { /* First byte (I2C command) is chip select */ - hw->buffer[0] = 1 << msg->spi->chip_select; + hw->buffer[0] = 1 << spi_get_chipselect(msg->spi, 0); hw->tlen = 1; hw->rindex = 0; } @@ -229,7 +229,7 @@ static int sc18is602_setup(struct spi_device *spi) struct sc18is602 *hw = spi_master_get_devdata(spi->master); /* SC18IS602 does not support CS2 */ - if (hw->id == sc18is602 && spi->chip_select == 2) + if (hw->id == sc18is602 && (spi_get_chipselect(spi, 0) == 2)) return -ENXIO; return 0; diff --git a/drivers/spi/spi-sh-msiof.c b/drivers/spi/spi-sh-msiof.c index 9bca3d076f053..87cb975ce9dc0 100644 --- a/drivers/spi/spi-sh-msiof.c +++ b/drivers/spi/spi-sh-msiof.c @@ -554,7 +554,7 @@ static int sh_msiof_spi_setup(struct spi_device *spi) spi_controller_get_devdata(spi->controller); u32 clr, set, tmp; - if (spi->cs_gpiod || spi_controller_is_slave(p->ctlr)) + if (spi_get_csgpiod(spi, 0) || spi_controller_is_slave(p->ctlr)) return 0; if (p->native_cs_inited && @@ -587,11 +587,11 @@ static int sh_msiof_prepare_message(struct spi_controller *ctlr, u32 ss, cs_high; /* Configure pins before asserting CS */ - if (spi->cs_gpiod) { + if (spi_get_csgpiod((struct spi_device *)spi, 0)) { ss = ctlr->unused_native_cs; cs_high = p->native_cs_high; } else { - ss = spi->chip_select; + ss = spi_get_chipselect((struct spi_device *)spi, 0); cs_high = !!(spi->mode & SPI_CS_HIGH); } sh_msiof_spi_set_pin_regs(p, ss, !!(spi->mode & SPI_CPOL), diff --git a/drivers/spi/spi-sh-sci.c b/drivers/spi/spi-sh-sci.c index 8f30531e14186..3003dd7c72c8a 100644 --- a/drivers/spi/spi-sh-sci.c +++ b/drivers/spi/spi-sh-sci.c @@ -108,7 +108,7 @@ static void sh_sci_spi_chipselect(struct spi_device *dev, int value) struct sh_sci_spi *sp = spi_master_get_devdata(dev->master); if (sp->info->chip_select) - (sp->info->chip_select)(sp->info, dev->chip_select, value); + (sp->info->chip_select)(sp->info, spi_get_chipselect(dev, 0), value); } static int sh_sci_spi_probe(struct platform_device *dev) diff --git a/drivers/spi/spi-sifive.c b/drivers/spi/spi-sifive.c index e29e85cee88a2..7840ef940ff8e 100644 --- a/drivers/spi/spi-sifive.c +++ b/drivers/spi/spi-sifive.c @@ -135,13 +135,13 @@ sifive_spi_prepare_message(struct spi_master *master, struct spi_message *msg) /* Update the chip select polarity */ if (device->mode & SPI_CS_HIGH) - spi->cs_inactive &= ~BIT(device->chip_select); + spi->cs_inactive &= ~BIT(spi_get_chipselect(device, 0)); else - spi->cs_inactive |= BIT(device->chip_select); + spi->cs_inactive |= BIT(spi_get_chipselect(device, 0)); sifive_spi_write(spi, SIFIVE_SPI_REG_CSDEF, spi->cs_inactive); /* Select the correct device */ - sifive_spi_write(spi, SIFIVE_SPI_REG_CSID, device->chip_select); + sifive_spi_write(spi, SIFIVE_SPI_REG_CSID, spi_get_chipselect(device, 0)); /* Set clock mode */ sifive_spi_write(spi, SIFIVE_SPI_REG_SCKMODE, diff --git a/drivers/spi/spi-sn-f-ospi.c b/drivers/spi/spi-sn-f-ospi.c index 0aedade8908c4..93fc1f6f39b83 100644 --- a/drivers/spi/spi-sn-f-ospi.c +++ b/drivers/spi/spi-sn-f-ospi.c @@ -267,7 +267,7 @@ static void f_ospi_config_indir_protocol(struct f_ospi *ospi, int unit; /* Set one chip select */ - writel(BIT(spi->chip_select), ospi->base + OSPI_SSEL); + writel(BIT(spi_get_chipselect(spi, 0)), ospi->base + OSPI_SSEL); mode = f_ospi_get_mode(ospi, op->cmd.buswidth, 1); prot |= FIELD_PREP(OSPI_PROT_MODE_CODE_MASK, mode); diff --git a/drivers/spi/spi-st-ssc4.c b/drivers/spi/spi-st-ssc4.c index 843be803696bc..57aaae39e5f84 100644 --- a/drivers/spi/spi-st-ssc4.c +++ b/drivers/spi/spi-st-ssc4.c @@ -183,7 +183,7 @@ static int spi_st_setup(struct spi_device *spi) return -EINVAL; } - if (!spi->cs_gpiod) { + if (!spi_get_csgpiod(spi, 0)) { dev_err(&spi->dev, "no valid gpio assigned\n"); return -EINVAL; } diff --git a/drivers/spi/spi-stm32-qspi.c b/drivers/spi/spi-stm32-qspi.c index 9131660c1afb2..b9e61372dcfbd 100644 --- a/drivers/spi/spi-stm32-qspi.c +++ b/drivers/spi/spi-stm32-qspi.c @@ -359,7 +359,7 @@ static int stm32_qspi_get_mode(u8 buswidth) static int stm32_qspi_send(struct spi_device *spi, const struct spi_mem_op *op) { struct stm32_qspi *qspi = spi_controller_get_devdata(spi->master); - struct stm32_qspi_flash *flash = &qspi->flash[spi->chip_select]; + struct stm32_qspi_flash *flash = &qspi->flash[spi_get_chipselect(spi, 0)]; u32 ccr, cr; int timeout, err = 0, err_poll_status = 0; @@ -564,7 +564,7 @@ static int stm32_qspi_transfer_one_message(struct spi_controller *ctrl, struct spi_mem_op op; int ret = 0; - if (!spi->cs_gpiod) + if (!spi_get_csgpiod(spi, 0)) return -EOPNOTSUPP; ret = pm_runtime_resume_and_get(qspi->dev); @@ -573,7 +573,7 @@ static int stm32_qspi_transfer_one_message(struct spi_controller *ctrl, mutex_lock(&qspi->lock); - gpiod_set_value_cansleep(spi->cs_gpiod, true); + gpiod_set_value_cansleep(spi_get_csgpiod(spi, 0), true); list_for_each_entry(transfer, &msg->transfers, transfer_list) { u8 dummy_bytes = 0; @@ -626,7 +626,7 @@ static int stm32_qspi_transfer_one_message(struct spi_controller *ctrl, } end_of_transfer: - gpiod_set_value_cansleep(spi->cs_gpiod, false); + gpiod_set_value_cansleep(spi_get_csgpiod(spi, 0), false); mutex_unlock(&qspi->lock); @@ -669,8 +669,8 @@ static int stm32_qspi_setup(struct spi_device *spi) presc = DIV_ROUND_UP(qspi->clk_rate, spi->max_speed_hz) - 1; - flash = &qspi->flash[spi->chip_select]; - flash->cs = spi->chip_select; + flash = &qspi->flash[spi_get_chipselect(spi, 0)]; + flash->cs = spi_get_chipselect(spi, 0); flash->presc = presc; mutex_lock(&qspi->lock); diff --git a/drivers/spi/spi-sun4i.c b/drivers/spi/spi-sun4i.c index 6000d0761206c..1e3b1922059e3 100644 --- a/drivers/spi/spi-sun4i.c +++ b/drivers/spi/spi-sun4i.c @@ -167,7 +167,7 @@ static void sun4i_spi_set_cs(struct spi_device *spi, bool enable) reg = sun4i_spi_read(sspi, SUN4I_CTL_REG); reg &= ~SUN4I_CTL_CS_MASK; - reg |= SUN4I_CTL_CS(spi->chip_select); + reg |= SUN4I_CTL_CS(spi_get_chipselect(spi, 0)); /* We want to control the chip select manually */ reg |= SUN4I_CTL_CS_MANUAL; diff --git a/drivers/spi/spi-sun6i.c b/drivers/spi/spi-sun6i.c index 23ad052528dbe..46e7c446503a5 100644 --- a/drivers/spi/spi-sun6i.c +++ b/drivers/spi/spi-sun6i.c @@ -174,7 +174,7 @@ static void sun6i_spi_set_cs(struct spi_device *spi, bool enable) reg = sun6i_spi_read(sspi, SUN6I_TFR_CTL_REG); reg &= ~SUN6I_TFR_CTL_CS_MASK; - reg |= SUN6I_TFR_CTL_CS(spi->chip_select); + reg |= SUN6I_TFR_CTL_CS(spi_get_chipselect(spi, 0)); if (enable) reg |= SUN6I_TFR_CTL_CS_LEVEL; diff --git a/drivers/spi/spi-synquacer.c b/drivers/spi/spi-synquacer.c index dc188f9202c97..733dc8c52b083 100644 --- a/drivers/spi/spi-synquacer.c +++ b/drivers/spi/spi-synquacer.c @@ -250,7 +250,7 @@ static int synquacer_spi_config(struct spi_master *master, } mode = spi->mode; - cs = spi->chip_select; + cs = spi_get_chipselect(spi, 0); speed = xfer->speed_hz; bpw = xfer->bits_per_word; @@ -344,7 +344,7 @@ static int synquacer_spi_config(struct spi_master *master, sspi->bpw = bpw; sspi->mode = mode; sspi->speed = speed; - sspi->cs = spi->chip_select; + sspi->cs = spi_get_chipselect(spi, 0); sspi->bus_width = bus_width; return 0; @@ -488,7 +488,7 @@ static void synquacer_spi_set_cs(struct spi_device *spi, bool enable) val = readl(sspi->regs + SYNQUACER_HSSPI_REG_DMSTART); val &= ~(SYNQUACER_HSSPI_DMPSEL_CS_MASK << SYNQUACER_HSSPI_DMPSEL_CS_SHIFT); - val |= spi->chip_select << SYNQUACER_HSSPI_DMPSEL_CS_SHIFT; + val |= spi_get_chipselect(spi, 0) << SYNQUACER_HSSPI_DMPSEL_CS_SHIFT; if (!enable) val |= SYNQUACER_HSSPI_DMSTOP_STOP; diff --git a/drivers/spi/spi-tegra114.c b/drivers/spi/spi-tegra114.c index d9be80e3e1bcb..e334183241d72 100644 --- a/drivers/spi/spi-tegra114.c +++ b/drivers/spi/spi-tegra114.c @@ -747,7 +747,7 @@ static int tegra_spi_set_hw_cs_timing(struct spi_device *spi) if (setup_dly && hold_dly) { setup_hold = SPI_SETUP_HOLD(setup_dly - 1, hold_dly - 1); spi_cs_timing = SPI_CS_SETUP_HOLD(tspi->spi_cs_timing1, - spi->chip_select, + spi_get_chipselect(spi, 0), setup_hold); if (tspi->spi_cs_timing1 != spi_cs_timing) { tspi->spi_cs_timing1 = spi_cs_timing; @@ -760,9 +760,9 @@ static int tegra_spi_set_hw_cs_timing(struct spi_device *spi) inactive_cycles--; cs_state = inactive_cycles ? 0 : 1; spi_cs_timing = tspi->spi_cs_timing2; - SPI_SET_CS_ACTIVE_BETWEEN_PACKETS(spi_cs_timing, spi->chip_select, + SPI_SET_CS_ACTIVE_BETWEEN_PACKETS(spi_cs_timing, spi_get_chipselect(spi, 0), cs_state); - SPI_SET_CYCLES_BETWEEN_PACKETS(spi_cs_timing, spi->chip_select, + SPI_SET_CYCLES_BETWEEN_PACKETS(spi_cs_timing, spi_get_chipselect(spi, 0), inactive_cycles); if (tspi->spi_cs_timing2 != spi_cs_timing) { tspi->spi_cs_timing2 = spi_cs_timing; @@ -831,8 +831,8 @@ static u32 tegra_spi_setup_transfer_one(struct spi_device *spi, tegra_spi_writel(tspi, command1, SPI_COMMAND1); /* GPIO based chip select control */ - if (spi->cs_gpiod) - gpiod_set_value(spi->cs_gpiod, 1); + if (spi_get_csgpiod(spi, 0)) + gpiod_set_value(spi_get_csgpiod(spi, 0), 1); if (is_single_xfer && !(t->cs_change)) { tspi->use_hw_based_cs = true; @@ -846,7 +846,7 @@ static u32 tegra_spi_setup_transfer_one(struct spi_device *spi, command1 &= ~SPI_CS_SW_VAL; } - if (tspi->last_used_cs != spi->chip_select) { + if (tspi->last_used_cs != spi_get_chipselect(spi, 0)) { if (cdata && cdata->tx_clk_tap_delay) tx_tap = cdata->tx_clk_tap_delay; if (cdata && cdata->rx_clk_tap_delay) @@ -855,7 +855,7 @@ static u32 tegra_spi_setup_transfer_one(struct spi_device *spi, SPI_RX_TAP_DELAY(rx_tap); if (command2 != tspi->def_command2_reg) tegra_spi_writel(tspi, command2, SPI_COMMAND2); - tspi->last_used_cs = spi->chip_select; + tspi->last_used_cs = spi_get_chipselect(spi, 0); } } else { @@ -896,7 +896,7 @@ static int tegra_spi_start_transfer_one(struct spi_device *spi, command1 |= SPI_TX_EN; tspi->cur_direction |= DATA_DIR_TX; } - command1 |= SPI_CS_SEL(spi->chip_select); + command1 |= SPI_CS_SEL(spi_get_chipselect(spi, 0)); tegra_spi_writel(tspi, command1, SPI_COMMAND1); tspi->command1_reg = command1; @@ -980,14 +980,14 @@ static int tegra_spi_setup(struct spi_device *spi) spin_lock_irqsave(&tspi->lock, flags); /* GPIO based chip select control */ - if (spi->cs_gpiod) - gpiod_set_value(spi->cs_gpiod, 0); + if (spi_get_csgpiod(spi, 0)) + gpiod_set_value(spi_get_csgpiod(spi, 0), 0); val = tspi->def_command1_reg; if (spi->mode & SPI_CS_HIGH) - val &= ~SPI_CS_POL_INACTIVE(spi->chip_select); + val &= ~SPI_CS_POL_INACTIVE(spi_get_chipselect(spi, 0)); else - val |= SPI_CS_POL_INACTIVE(spi->chip_select); + val |= SPI_CS_POL_INACTIVE(spi_get_chipselect(spi, 0)); tspi->def_command1_reg = val; tegra_spi_writel(tspi, tspi->def_command1_reg, SPI_COMMAND1); spin_unlock_irqrestore(&tspi->lock, flags); @@ -1002,8 +1002,8 @@ static void tegra_spi_transfer_end(struct spi_device *spi) int cs_val = (spi->mode & SPI_CS_HIGH) ? 0 : 1; /* GPIO based chip select control */ - if (spi->cs_gpiod) - gpiod_set_value(spi->cs_gpiod, 0); + if (spi_get_csgpiod(spi, 0)) + gpiod_set_value(spi_get_csgpiod(spi, 0), 0); if (!tspi->use_hw_based_cs) { if (cs_val) diff --git a/drivers/spi/spi-tegra20-sflash.c b/drivers/spi/spi-tegra20-sflash.c index 220ee08c4a06c..f67d0aafa744c 100644 --- a/drivers/spi/spi-tegra20-sflash.c +++ b/drivers/spi/spi-tegra20-sflash.c @@ -280,7 +280,7 @@ static int tegra_sflash_start_transfer_one(struct spi_device *spi, command |= SPI_ACTIVE_SCLK_DRIVE_HIGH; else command |= SPI_ACTIVE_SCLK_DRIVE_LOW; - command |= SPI_CS0_EN << spi->chip_select; + command |= SPI_CS0_EN << spi_get_chipselect(spi, 0); } else { command = tsd->command_reg; command &= ~SPI_BIT_LENGTH(~0); diff --git a/drivers/spi/spi-tegra20-slink.c b/drivers/spi/spi-tegra20-slink.c index 148043d0c2b84..0afba7dbd93aa 100644 --- a/drivers/spi/spi-tegra20-slink.c +++ b/drivers/spi/spi-tegra20-slink.c @@ -758,9 +758,9 @@ static int tegra_slink_setup(struct spi_device *spi) spin_lock_irqsave(&tspi->lock, flags); val = tspi->def_command_reg; if (spi->mode & SPI_CS_HIGH) - val |= cs_pol_bit[spi->chip_select]; + val |= cs_pol_bit[spi_get_chipselect(spi, 0)]; else - val &= ~cs_pol_bit[spi->chip_select]; + val &= ~cs_pol_bit[spi_get_chipselect(spi, 0)]; tspi->def_command_reg = val; tegra_slink_writel(tspi, tspi->def_command_reg, SLINK_COMMAND); spin_unlock_irqrestore(&tspi->lock, flags); @@ -781,7 +781,7 @@ static int tegra_slink_prepare_message(struct spi_master *master, tspi->command_reg |= SLINK_CS_SW | SLINK_CS_VALUE; tspi->command2_reg = tspi->def_command2_reg; - tspi->command2_reg |= SLINK_SS_EN_CS(spi->chip_select); + tspi->command2_reg |= SLINK_SS_EN_CS(spi_get_chipselect(spi, 0)); tspi->command_reg &= ~SLINK_MODES; if (spi->mode & SPI_CPHA) diff --git a/drivers/spi/spi-tegra210-quad.c b/drivers/spi/spi-tegra210-quad.c index 0b9bc3b7f53a7..80c3bd9f8bc15 100644 --- a/drivers/spi/spi-tegra210-quad.c +++ b/drivers/spi/spi-tegra210-quad.c @@ -829,7 +829,7 @@ static u32 tegra_qspi_setup_transfer_one(struct spi_device *spi, struct spi_tran tegra_qspi_mask_clear_irq(tqspi); command1 = tqspi->def_command1_reg; - command1 |= QSPI_CS_SEL(spi->chip_select); + command1 |= QSPI_CS_SEL(spi_get_chipselect(spi, 0)); command1 |= QSPI_BIT_LENGTH(bits_per_word - 1); command1 &= ~QSPI_CONTROL_MODE_MASK; @@ -960,11 +960,11 @@ static int tegra_qspi_setup(struct spi_device *spi) /* keep default cs state to inactive */ val = tqspi->def_command1_reg; - val |= QSPI_CS_SEL(spi->chip_select); + val |= QSPI_CS_SEL(spi_get_chipselect(spi, 0)); if (spi->mode & SPI_CS_HIGH) - val &= ~QSPI_CS_POL_INACTIVE(spi->chip_select); + val &= ~QSPI_CS_POL_INACTIVE(spi_get_chipselect(spi, 0)); else - val |= QSPI_CS_POL_INACTIVE(spi->chip_select); + val |= QSPI_CS_POL_INACTIVE(spi_get_chipselect(spi, 0)); tqspi->def_command1_reg = val; tegra_qspi_writel(tqspi, tqspi->def_command1_reg, QSPI_COMMAND1); diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c index 60086869bcae4..5914335ff63db 100644 --- a/drivers/spi/spi-ti-qspi.c +++ b/drivers/spi/spi-ti-qspi.c @@ -533,10 +533,10 @@ static void ti_qspi_enable_memory_map(struct spi_device *spi) if (qspi->ctrl_base) { regmap_update_bits(qspi->ctrl_base, qspi->ctrl_reg, MEM_CS_MASK, - MEM_CS_EN(spi->chip_select)); + MEM_CS_EN(spi_get_chipselect(spi, 0))); } qspi->mmap_enabled = true; - qspi->current_cs = spi->chip_select; + qspi->current_cs = spi_get_chipselect(spi, 0); } static void ti_qspi_disable_memory_map(struct spi_device *spi) @@ -572,7 +572,7 @@ static void ti_qspi_setup_mmap_read(struct spi_device *spi, u8 opcode, memval |= ((addr_width - 1) << QSPI_SETUP_ADDR_SHIFT | dummy_bytes << QSPI_SETUP_DUMMY_SHIFT); ti_qspi_write(qspi, memval, - QSPI_SPI_SETUP_REG(spi->chip_select)); + QSPI_SPI_SETUP_REG(spi_get_chipselect(spi, 0))); } static int ti_qspi_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op) @@ -623,7 +623,7 @@ static int ti_qspi_exec_mem_op(struct spi_mem *mem, mutex_lock(&qspi->list_lock); - if (!qspi->mmap_enabled || qspi->current_cs != mem->spi->chip_select) { + if (!qspi->mmap_enabled || qspi->current_cs != spi_get_chipselect(mem->spi, 0)) { ti_qspi_setup_clk(qspi, mem->spi->max_speed_hz); ti_qspi_enable_memory_map(mem->spi); } @@ -673,11 +673,11 @@ static int ti_qspi_start_transfer_one(struct spi_master *master, qspi->dc = 0; if (spi->mode & SPI_CPHA) - qspi->dc |= QSPI_CKPHA(spi->chip_select); + qspi->dc |= QSPI_CKPHA(spi_get_chipselect(spi, 0)); if (spi->mode & SPI_CPOL) - qspi->dc |= QSPI_CKPOL(spi->chip_select); + qspi->dc |= QSPI_CKPOL(spi_get_chipselect(spi, 0)); if (spi->mode & SPI_CS_HIGH) - qspi->dc |= QSPI_CSPOL(spi->chip_select); + qspi->dc |= QSPI_CSPOL(spi_get_chipselect(spi, 0)); frame_len_words = 0; list_for_each_entry(t, &m->transfers, transfer_list) @@ -686,7 +686,7 @@ static int ti_qspi_start_transfer_one(struct spi_master *master, /* setup command reg */ qspi->cmd = 0; - qspi->cmd |= QSPI_EN_CS(spi->chip_select); + qspi->cmd |= QSPI_EN_CS(spi_get_chipselect(spi, 0)); qspi->cmd |= QSPI_FLEN(frame_len_words); ti_qspi_write(qspi, qspi->dc, QSPI_SPI_DC_REG); diff --git a/drivers/spi/spi-topcliff-pch.c b/drivers/spi/spi-topcliff-pch.c index cbb60198a7f00..11cfe84714e71 100644 --- a/drivers/spi/spi-topcliff-pch.c +++ b/drivers/spi/spi-topcliff-pch.c @@ -499,7 +499,7 @@ static inline void pch_spi_select_chip(struct pch_spi_data *data, struct spi_device *pspi) { if (data->current_chip != NULL) { - if (pspi->chip_select != data->n_curnt_chip) { + if (spi_get_chipselect(pspi, 0) != data->n_curnt_chip) { dev_dbg(&pspi->dev, "%s : different slave\n", __func__); data->current_chip = NULL; } @@ -507,7 +507,7 @@ static inline void pch_spi_select_chip(struct pch_spi_data *data, data->current_chip = pspi; - data->n_curnt_chip = data->current_chip->chip_select; + data->n_curnt_chip = spi_get_chipselect(data->current_chip, 0); dev_dbg(&pspi->dev, "%s :Invoking pch_spi_setup_transfer\n", __func__); pch_spi_setup_transfer(pspi); diff --git a/drivers/spi/spi-wpcm-fiu.c b/drivers/spi/spi-wpcm-fiu.c index ab33710d50ac8..f15312fdcdaf0 100644 --- a/drivers/spi/spi-wpcm-fiu.c +++ b/drivers/spi/spi-wpcm-fiu.c @@ -158,7 +158,7 @@ static int wpcm_fiu_normal_exec(struct spi_mem *mem, const struct spi_mem_op *op if (op->data.dir == SPI_MEM_DATA_OUT) wpcm_fiu_set_data(fiu, op->data.buf.out, op->data.nbytes); - ret = wpcm_fiu_do_uma(fiu, mem->spi->chip_select, op->addr.nbytes == 3, + ret = wpcm_fiu_do_uma(fiu, spi_get_chipselect(mem->spi, 0), op->addr.nbytes == 3, op->data.dir == SPI_MEM_DATA_OUT, op->data.nbytes); if (op->data.dir == SPI_MEM_DATA_IN) @@ -196,7 +196,7 @@ static bool wpcm_fiu_4ba_match(const struct spi_mem_op *op) static int wpcm_fiu_4ba_exec(struct spi_mem *mem, const struct spi_mem_op *op) { struct wpcm_fiu_spi *fiu = spi_controller_get_devdata(mem->spi->controller); - int cs = mem->spi->chip_select; + int cs = spi_get_chipselect(mem->spi, 0); wpcm_fiu_ects_assert(fiu, cs); @@ -241,7 +241,7 @@ static bool wpcm_fiu_rdid_match(const struct spi_mem_op *op) static int wpcm_fiu_rdid_exec(struct spi_mem *mem, const struct spi_mem_op *op) { struct wpcm_fiu_spi *fiu = spi_controller_get_devdata(mem->spi->controller); - int cs = mem->spi->chip_select; + int cs = spi_get_chipselect(mem->spi, 0); /* First transfer */ wpcm_fiu_set_opcode(fiu, op->cmd.opcode); @@ -278,7 +278,7 @@ static bool wpcm_fiu_dummy_match(const struct spi_mem_op *op) static int wpcm_fiu_dummy_exec(struct spi_mem *mem, const struct spi_mem_op *op) { struct wpcm_fiu_spi *fiu = spi_controller_get_devdata(mem->spi->controller); - int cs = mem->spi->chip_select; + int cs = spi_get_chipselect(mem->spi, 0); wpcm_fiu_ects_assert(fiu, cs); @@ -376,7 +376,7 @@ static int wpcm_fiu_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op) static int wpcm_fiu_dirmap_create(struct spi_mem_dirmap_desc *desc) { struct wpcm_fiu_spi *fiu = spi_controller_get_devdata(desc->mem->spi->controller); - int cs = desc->mem->spi->chip_select; + int cs = spi_get_chipselect(desc->mem->spi, 0); if (desc->info.op_tmpl.data.dir != SPI_MEM_DATA_IN) return -ENOTSUPP; @@ -400,7 +400,7 @@ static int wpcm_fiu_dirmap_create(struct spi_mem_dirmap_desc *desc) static ssize_t wpcm_fiu_direct_read(struct spi_mem_dirmap_desc *desc, u64 offs, size_t len, void *buf) { struct wpcm_fiu_spi *fiu = spi_controller_get_devdata(desc->mem->spi->controller); - int cs = desc->mem->spi->chip_select; + int cs = spi_get_chipselect(desc->mem->spi, 0); if (offs >= MAX_MEMORY_SIZE_PER_CS) return -ENOTSUPP; diff --git a/drivers/spi/spi-xcomm.c b/drivers/spi/spi-xcomm.c index 8628241ec99e4..5d23411f2a3e9 100644 --- a/drivers/spi/spi-xcomm.c +++ b/drivers/spi/spi-xcomm.c @@ -58,7 +58,7 @@ static int spi_xcomm_sync_config(struct spi_xcomm *spi_xcomm, unsigned int len) static void spi_xcomm_chipselect(struct spi_xcomm *spi_xcomm, struct spi_device *spi, int is_active) { - unsigned long cs = spi->chip_select; + unsigned long cs = spi_get_chipselect(spi, 0); uint16_t chipselect = spi_xcomm->chipselect; if (is_active) diff --git a/drivers/spi/spi-xilinx.c b/drivers/spi/spi-xilinx.c index 1411548f42553..a2422c1636f4c 100644 --- a/drivers/spi/spi-xilinx.c +++ b/drivers/spi/spi-xilinx.c @@ -213,7 +213,7 @@ static void xilinx_spi_chipselect(struct spi_device *spi, int is_on) */ cs = xspi->cs_inactive; - cs ^= BIT(spi->chip_select); + cs ^= BIT(spi_get_chipselect(spi, 0)); /* Activate the chip select */ xspi->write_fn(cs, xspi->regs + XSPI_SSR_OFFSET); @@ -228,9 +228,9 @@ static int xilinx_spi_setup_transfer(struct spi_device *spi, struct xilinx_spi *xspi = spi_master_get_devdata(spi->master); if (spi->mode & SPI_CS_HIGH) - xspi->cs_inactive &= ~BIT(spi->chip_select); + xspi->cs_inactive &= ~BIT(spi_get_chipselect(spi, 0)); else - xspi->cs_inactive |= BIT(spi->chip_select); + xspi->cs_inactive |= BIT(spi_get_chipselect(spi, 0)); return 0; } diff --git a/drivers/spi/spi-xlp.c b/drivers/spi/spi-xlp.c index e5707fe5c8f15..3b91cdd5ae21e 100644 --- a/drivers/spi/spi-xlp.c +++ b/drivers/spi/spi-xlp.c @@ -139,7 +139,7 @@ static int xlp_spi_setup(struct spi_device *spi) int cs; xspi = spi_master_get_devdata(spi->master); - cs = spi->chip_select; + cs = spi_get_chipselect(spi, 0); /* * The value of fdiv must be between 4 and 65535. */ @@ -350,7 +350,7 @@ static int xlp_spi_transfer_one(struct spi_master *master, struct xlp_spi_priv *xspi = spi_master_get_devdata(master); int ret = 0; - xspi->cs = spi->chip_select; + xspi->cs = spi_get_chipselect(spi, 0); xspi->dev = spi->dev; if (spi_transfer_is_last(master, t)) diff --git a/drivers/spi/spi-zynq-qspi.c b/drivers/spi/spi-zynq-qspi.c index 78f31b61a2aac..debb53ef19a09 100644 --- a/drivers/spi/spi-zynq-qspi.c +++ b/drivers/spi/spi-zynq-qspi.c @@ -296,7 +296,7 @@ static void zynq_qspi_chipselect(struct spi_device *spi, bool assert) /* Select the lower (CS0) or upper (CS1) memory */ if (ctlr->num_chipselect > 1) { config_reg = zynq_qspi_read(xqspi, ZYNQ_QSPI_LINEAR_CFG_OFFSET); - if (!spi->chip_select) + if (!spi_get_chipselect(spi, 0)) config_reg &= ~ZYNQ_QSPI_LCFG_U_PAGE; else config_reg |= ZYNQ_QSPI_LCFG_U_PAGE; diff --git a/drivers/spi/spi-zynqmp-gqspi.c b/drivers/spi/spi-zynqmp-gqspi.c index 95ff15665d448..319cdd5a0bdcb 100644 --- a/drivers/spi/spi-zynqmp-gqspi.c +++ b/drivers/spi/spi-zynqmp-gqspi.c @@ -468,7 +468,7 @@ static void zynqmp_qspi_chipselect(struct spi_device *qspi, bool is_high) genfifoentry |= GQSPI_GENFIFO_MODE_SPI; if (!is_high) { - if (!qspi->chip_select) { + if (!spi_get_chipselect(qspi, 0)) { xqspi->genfifobus = GQSPI_GENFIFO_BUS_LOWER; xqspi->genfifocs = GQSPI_GENFIFO_CS_LOWER; } else { diff --git a/drivers/spi/spidev.c b/drivers/spi/spidev.c index 5a038c6674018..a399c617ca25f 100644 --- a/drivers/spi/spidev.c +++ b/drivers/spi/spidev.c @@ -393,7 +393,7 @@ spidev_ioctl(struct file *filp, unsigned int cmd, unsigned long arg) struct spi_controller *ctlr = spi->controller; if (ctlr->use_gpio_descriptors && ctlr->cs_gpiods && - ctlr->cs_gpiods[spi->chip_select]) + ctlr->cs_gpiods[spi_get_chipselect(spi, 0)]) tmp &= ~SPI_CS_HIGH; } @@ -432,7 +432,7 @@ spidev_ioctl(struct file *filp, unsigned int cmd, unsigned long arg) } if (ctlr->use_gpio_descriptors && ctlr->cs_gpiods && - ctlr->cs_gpiods[spi->chip_select]) + ctlr->cs_gpiods[spi_get_chipselect(spi, 0)]) tmp |= SPI_CS_HIGH; tmp |= spi->mode & ~SPI_MODE_MASK; @@ -805,7 +805,7 @@ static int spidev_probe(struct spi_device *spi) spidev->devt = MKDEV(SPIDEV_MAJOR, minor); dev = device_create(spidev_class, &spi->dev, spidev->devt, spidev, "spidev%d.%d", - spi->master->bus_num, spi->chip_select); + spi->master->bus_num, spi_get_chipselect(spi, 0)); status = PTR_ERR_OR_ZERO(dev); } else { dev_dbg(&spi->dev, "no minor number available!\n"); diff --git a/include/trace/events/spi.h b/include/trace/events/spi.h index c0d9844befd7a..c0248a8fa79c9 100644 --- a/include/trace/events/spi.h +++ b/include/trace/events/spi.h @@ -57,7 +57,7 @@ TRACE_EVENT(spi_setup, TP_fast_assign( __entry->bus_num = spi->controller->bus_num; - __entry->chip_select = spi->chip_select; + __entry->chip_select = spi_get_chipselect(spi, 0); __entry->mode = spi->mode; __entry->bits_per_word = spi->bits_per_word; __entry->max_speed_hz = spi->max_speed_hz; @@ -88,7 +88,7 @@ TRACE_EVENT(spi_set_cs, TP_fast_assign( __entry->bus_num = spi->controller->bus_num; - __entry->chip_select = spi->chip_select; + __entry->chip_select = spi_get_chipselect(spi, 0); __entry->mode = spi->mode; __entry->enable = enable; ), @@ -113,7 +113,7 @@ DECLARE_EVENT_CLASS(spi_message, TP_fast_assign( __entry->bus_num = msg->spi->controller->bus_num; - __entry->chip_select = msg->spi->chip_select; + __entry->chip_select = spi_get_chipselect(msg->spi, 0); __entry->msg = msg; ), @@ -154,7 +154,7 @@ TRACE_EVENT(spi_message_done, TP_fast_assign( __entry->bus_num = msg->spi->controller->bus_num; - __entry->chip_select = msg->spi->chip_select; + __entry->chip_select = spi_get_chipselect(msg->spi, 0); __entry->msg = msg; __entry->frame = msg->frame_length; __entry->actual = msg->actual_length; @@ -197,7 +197,7 @@ DECLARE_EVENT_CLASS(spi_transfer, TP_fast_assign( __entry->bus_num = msg->spi->controller->bus_num; - __entry->chip_select = msg->spi->chip_select; + __entry->chip_select = spi_get_chipselect(msg->spi, 0); __entry->xfer = xfer; __entry->len = xfer->len;

1 0

[PATCH] Make snd-hda-intel work for HP Envy x360 15-ew0xxx (Realtek ALC245)
by Matthias Ostermaier 06 May '23

06 May '23

Hardware: HP laptop models HP Envy x360 15-ew0xxx (with codec Realtek ALC245 and Cirrus Logic Smart Amplifier chipset CSC3551) vendor_id: 0x10ec0245, subsystem_id: 0x103c8a29, revision_id:0x100001 Kernel version: 6.2+ Output of alsa-info.sh attached (with the patch applied) Patch repository for reference: https://github.com/xoocoon/hp-15-ew0xxx-snd-fix Problem description: The CSC3551 chipset does not get initialized correctly in aforementioned laptop models. While the rest of snd-hda-intel recognizes the hardware correctly, the smart amplifier does not get initialized so that the built-in loudspeakers do not work. The patch is confirmed to work by another user owning said laptop model. Patches: -------------------------------------------------------------------------- -- sound/pci/hda/cs35l41_hda.c | 4 ++++ sound/pci/hda/patch_realtek.c | 1 + 2 files changed, 5 insertions(+) diff --git a/sound/pci/hda/cs35l41_hda.c b/sound/pci/hda/cs35l41_hda.c index b5210abb5141..67ec4a0ec023 100644 --- a/sound/pci/hda/cs35l41_hda.c +++ b/sound/pci/hda/cs35l41_hda.c @@ -1243,6 +1243,10 @@ static int cs35l41_no_acpi_dsd(struct cs35l41_hda *cs35l41, struct device *physd hw_cfg->bst_type = CS35L41_EXT_BOOST; hw_cfg->gpio1.func = CS35l41_VSPK_SWITCH; hw_cfg->gpio1.valid = true; + } else if (strncmp(hid, "CSC3551", 7) == 0) { + hw_cfg->bst_type = CS35L41_EXT_BOOST; + hw_cfg->gpio1.func = CS35l41_VSPK_SWITCH; + hw_cfg->gpio1.valid = true; } else { /* * Note: CLSA010(0/1) are special cases which use a slightly different design. diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 172ffc2c332b..57712ff62729 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -9458,6 +9458,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x103c, 0x8aa3, "HP ProBook 450 G9 (MB 8AA1)", ALC236_FIXUP_HP_GPIO_LED), SND_PCI_QUIRK(0x103c, 0x8aa8, "HP EliteBook 640 G9 (MB 8AA6)", ALC236_FIXUP_HP_GPIO_LED), SND_PCI_QUIRK(0x103c, 0x8aab, "HP EliteBook 650 G9 (MB 8AA9)", ALC236_FIXUP_HP_GPIO_LED), + SND_PCI_QUIRK(0x103c, 0x8a29, "HP Envy x360 15-ew0xxx", ALC287_FIXUP_CS35L41_I2C_2), SND_PCI_QUIRK(0x103c, 0x8abb, "HP ZBook Firefly 14 G9", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED), SND_PCI_QUIRK(0x103c, 0x8ad1, "HP EliteBook 840 14 inch G9 Notebook PC", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED), SND_PCI_QUIRK(0x103c, 0x8ad2, "HP EliteBook 860 16 inch G9 Notebook PC", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED), -------------------------------------------------------------------------- Unresolved issues: The LED indicating muted sound on the laptop keyboard does not work. The same holds for the LED indicating a deactivated microphone. These issues are not addressed by the patches.

1 0

[PATCH 0/3] ASoC: hdmi-codec: add component name prefix to controls
by Srinivas Kandagatla 06 May '23

06 May '23

While adding audio support to two instances of Display port on x13s, hdmi-codec failed to add controls as two codec instances were trying to add controls with same name. snd-sc8280xp sound: control 3:16:0:IEC958 Playback Mask:0 is already present snd-sc8280xp sound: control 3:16:0:Playback Channel Map:0 is already present hdmi-audio-codec hdmi-audio-codec.4.auto: ASoC: error at snd_soc_pcm_dai_new on i2s-hifi: -16 To fix this issue, I have added a new api snd_pcm_add_chmap_ctls_with_prefix() to allow to pass asoc component name prefix, which should provide a unique control names. We can also make snd_pcm_add_chmap_ctls() take prefix argument to do the same this. Srinivas Kandagatla (3): ALSA: pcm: add snd_pcm_add_chmap_ctls_with_prefix ASoC: hdmi-codec: use snd_pcm_add_chmap_ctls_with_prefix to add controls ASoC: hdmi-codec: use snd_soc_cnew to add controls include/sound/pcm.h | 7 +++++++ sound/core/pcm_lib.c | 30 ++++++++++++++++++++++++++++-- sound/soc/codecs/hdmi-codec.c | 10 ++++++---- 3 files changed, 41 insertions(+), 6 deletions(-) -- 2.21.0

2 5

Patch "sound/oss/dmasound: fix build when drivers are mixed =y/=m" has been added to the 5.15-stable tree
by gregkh＠linuxfoundation.org 06 May '23

06 May '23

This is a note to let you know that I've just added the patch titled sound/oss/dmasound: fix build when drivers are mixed =y/=m to the 5.15-stable tree which can be found at: http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=sum… The filename of the patch is: sound-oss-dmasound-fix-build-when-drivers-are-mixed-y-m.patch and it can be found in the queue-5.15 subdirectory. If you, or anyone else, feels it should not be added to the stable tree, please let <stable(a)vger.kernel.org> know about it. From 9dd7c46346ca4390f84a7ea9933005eb1b175c15 Mon Sep 17 00:00:00 2001 From: Randy Dunlap <rdunlap(a)infradead.org> Date: Tue, 5 Apr 2022 16:41:18 -0700 Subject: sound/oss/dmasound: fix build when drivers are mixed =y/=m From: Randy Dunlap <rdunlap(a)infradead.org> commit 9dd7c46346ca4390f84a7ea9933005eb1b175c15 upstream. When CONFIG_DMASOUND_ATARI=m and CONFIG_DMASOUND_Q40=y (or vice versa), dmasound_core.o can be built without dmasound_deinit() being defined, causing a build error: ERROR: modpost: "dmasound_deinit" [sound/oss/dmasound/dmasound_atari.ko] undefined! Modify dmasound_core.c and dmasound.h so that dmasound_deinit() is always available. The mixed modes (=y/=m) also mean that several variables and structs have to be declared in all cases. Suggested-by: Arnd Bergmann <arnd(a)arndb.de> Suggested-by: Geert Uytterhoeven <geert(a)linux-m68k.org> Signed-off-by: Randy Dunlap <rdunlap(a)infradead.org> Reported-by: kernel test robot <lkp(a)intel.com> Link: lore.kernel.org/r/202204032138.EFT9qGEd-lkp@intel.com Cc: Geert Uytterhoeven <geert(a)linux-m68k.org> Cc: Jaroslav Kysela <perex(a)perex.cz> Cc: Takashi Iwai <tiwai(a)suse.com> Cc: alsa-devel(a)alsa-project.org Link: https://lore.kernel.org/r/20220405234118.24830-1-rdunlap@infradead.org Signed-off-by: Takashi Iwai <tiwai(a)suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- sound/oss/dmasound/dmasound.h | 6 ------ sound/oss/dmasound/dmasound_core.c | 24 +----------------------- 2 files changed, 1 insertion(+), 29 deletions(-) --- a/sound/oss/dmasound/dmasound.h +++ b/sound/oss/dmasound/dmasound.h @@ -88,11 +88,7 @@ static inline int ioctl_return(int __use */ extern int dmasound_init(void); -#ifdef MODULE extern void dmasound_deinit(void); -#else -#define dmasound_deinit() do { } while (0) -#endif /* description of the set-up applies to either hard or soft settings */ @@ -114,9 +110,7 @@ typedef struct { void *(*dma_alloc)(unsigned int, gfp_t); void (*dma_free)(void *, unsigned int); int (*irqinit)(void); -#ifdef MODULE void (*irqcleanup)(void); -#endif void (*init)(void); void (*silence)(void); int (*setFormat)(int); --- a/sound/oss/dmasound/dmasound_core.c +++ b/sound/oss/dmasound/dmasound_core.c @@ -206,12 +206,10 @@ module_param(writeBufSize, int, 0); MODULE_LICENSE("GPL"); -#ifdef MODULE static int sq_unit = -1; static int mixer_unit = -1; static int state_unit = -1; static int irq_installed; -#endif /* MODULE */ /* control over who can modify resources shared between play/record */ static fmode_t shared_resource_owner; @@ -391,9 +389,6 @@ static const struct file_operations mixe static void mixer_init(void) { -#ifndef MODULE - int mixer_unit; -#endif mixer_unit = register_sound_mixer(&mixer_fops, -1); if (mixer_unit < 0) return; @@ -1171,9 +1166,6 @@ static const struct file_operations sq_f static int sq_init(void) { const struct file_operations *fops = &sq_fops; -#ifndef MODULE - int sq_unit; -#endif sq_unit = register_sound_dsp(fops, -1); if (sq_unit < 0) { @@ -1366,9 +1358,6 @@ static const struct file_operations stat static int state_init(void) { -#ifndef MODULE - int state_unit; -#endif state_unit = register_sound_special(&state_fops, SND_DEV_STATUS); if (state_unit < 0) return state_unit ; @@ -1386,10 +1375,9 @@ static int state_init(void) int dmasound_init(void) { int res ; -#ifdef MODULE + if (irq_installed) return -EBUSY; -#endif /* Set up sound queue, /dev/audio and /dev/dsp. */ @@ -1408,9 +1396,7 @@ int dmasound_init(void) printk(KERN_ERR "DMA sound driver: Interrupt initialization failed\n"); return -ENODEV; } -#ifdef MODULE irq_installed = 1; -#endif printk(KERN_INFO "%s DMA sound driver rev %03d installed\n", dmasound.mach.name, (DMASOUND_CORE_REVISION<<4) + @@ -1424,8 +1410,6 @@ int dmasound_init(void) return 0; } -#ifdef MODULE - void dmasound_deinit(void) { if (irq_installed) { @@ -1444,8 +1428,6 @@ void dmasound_deinit(void) unregister_sound_dsp(sq_unit); } -#else /* !MODULE */ - static int dmasound_setup(char *str) { int ints[6], size; @@ -1489,8 +1471,6 @@ static int dmasound_setup(char *str) __setup("dmasound=", dmasound_setup); -#endif /* !MODULE */ - /* * Conversion tables */ @@ -1577,9 +1557,7 @@ char dmasound_alaw2dma8[] = { EXPORT_SYMBOL(dmasound); EXPORT_SYMBOL(dmasound_init); -#ifdef MODULE EXPORT_SYMBOL(dmasound_deinit); -#endif EXPORT_SYMBOL(dmasound_write_sq); EXPORT_SYMBOL(dmasound_catchRadius); #ifdef HAS_8BIT_TABLES Patches currently in stable-queue which might be from rdunlap(a)infradead.org are queue-5.15/sound-oss-dmasound-fix-build-when-drivers-are-mixed-y-m.patch queue-5.15/ima-allow-fix-uml-builds.patch

1 0

Patch "sound/oss/dmasound: fix build when drivers are mixed =y/=m" has been added to the 5.10-stable tree
by gregkh＠linuxfoundation.org 06 May '23

06 May '23

This is a note to let you know that I've just added the patch titled sound/oss/dmasound: fix build when drivers are mixed =y/=m to the 5.10-stable tree which can be found at: http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=sum… The filename of the patch is: sound-oss-dmasound-fix-build-when-drivers-are-mixed-y-m.patch and it can be found in the queue-5.10 subdirectory. If you, or anyone else, feels it should not be added to the stable tree, please let <stable(a)vger.kernel.org> know about it. From 9dd7c46346ca4390f84a7ea9933005eb1b175c15 Mon Sep 17 00:00:00 2001 From: Randy Dunlap <rdunlap(a)infradead.org> Date: Tue, 5 Apr 2022 16:41:18 -0700 Subject: sound/oss/dmasound: fix build when drivers are mixed =y/=m From: Randy Dunlap <rdunlap(a)infradead.org> commit 9dd7c46346ca4390f84a7ea9933005eb1b175c15 upstream. When CONFIG_DMASOUND_ATARI=m and CONFIG_DMASOUND_Q40=y (or vice versa), dmasound_core.o can be built without dmasound_deinit() being defined, causing a build error: ERROR: modpost: "dmasound_deinit" [sound/oss/dmasound/dmasound_atari.ko] undefined! Modify dmasound_core.c and dmasound.h so that dmasound_deinit() is always available. The mixed modes (=y/=m) also mean that several variables and structs have to be declared in all cases. Suggested-by: Arnd Bergmann <arnd(a)arndb.de> Suggested-by: Geert Uytterhoeven <geert(a)linux-m68k.org> Signed-off-by: Randy Dunlap <rdunlap(a)infradead.org> Reported-by: kernel test robot <lkp(a)intel.com> Link: lore.kernel.org/r/202204032138.EFT9qGEd-lkp@intel.com Cc: Geert Uytterhoeven <geert(a)linux-m68k.org> Cc: Jaroslav Kysela <perex(a)perex.cz> Cc: Takashi Iwai <tiwai(a)suse.com> Cc: alsa-devel(a)alsa-project.org Link: https://lore.kernel.org/r/20220405234118.24830-1-rdunlap@infradead.org Signed-off-by: Takashi Iwai <tiwai(a)suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh(a)linuxfoundation.org> --- sound/oss/dmasound/dmasound.h | 6 ------ sound/oss/dmasound/dmasound_core.c | 24 +----------------------- 2 files changed, 1 insertion(+), 29 deletions(-) --- a/sound/oss/dmasound/dmasound.h +++ b/sound/oss/dmasound/dmasound.h @@ -88,11 +88,7 @@ static inline int ioctl_return(int __use */ extern int dmasound_init(void); -#ifdef MODULE extern void dmasound_deinit(void); -#else -#define dmasound_deinit() do { } while (0) -#endif /* description of the set-up applies to either hard or soft settings */ @@ -114,9 +110,7 @@ typedef struct { void *(*dma_alloc)(unsigned int, gfp_t); void (*dma_free)(void *, unsigned int); int (*irqinit)(void); -#ifdef MODULE void (*irqcleanup)(void); -#endif void (*init)(void); void (*silence)(void); int (*setFormat)(int); --- a/sound/oss/dmasound/dmasound_core.c +++ b/sound/oss/dmasound/dmasound_core.c @@ -206,12 +206,10 @@ module_param(writeBufSize, int, 0); MODULE_LICENSE("GPL"); -#ifdef MODULE static int sq_unit = -1; static int mixer_unit = -1; static int state_unit = -1; static int irq_installed; -#endif /* MODULE */ /* control over who can modify resources shared between play/record */ static fmode_t shared_resource_owner; @@ -391,9 +389,6 @@ static const struct file_operations mixe static void mixer_init(void) { -#ifndef MODULE - int mixer_unit; -#endif mixer_unit = register_sound_mixer(&mixer_fops, -1); if (mixer_unit < 0) return; @@ -1176,9 +1171,6 @@ static const struct file_operations sq_f static int sq_init(void) { const struct file_operations *fops = &sq_fops; -#ifndef MODULE - int sq_unit; -#endif sq_unit = register_sound_dsp(fops, -1); if (sq_unit < 0) { @@ -1380,9 +1372,6 @@ static const struct file_operations stat static int state_init(void) { -#ifndef MODULE - int state_unit; -#endif state_unit = register_sound_special(&state_fops, SND_DEV_STATUS); if (state_unit < 0) return state_unit ; @@ -1400,10 +1389,9 @@ static int state_init(void) int dmasound_init(void) { int res ; -#ifdef MODULE + if (irq_installed) return -EBUSY; -#endif /* Set up sound queue, /dev/audio and /dev/dsp. */ @@ -1422,9 +1410,7 @@ int dmasound_init(void) printk(KERN_ERR "DMA sound driver: Interrupt initialization failed\n"); return -ENODEV; } -#ifdef MODULE irq_installed = 1; -#endif printk(KERN_INFO "%s DMA sound driver rev %03d installed\n", dmasound.mach.name, (DMASOUND_CORE_REVISION<<4) + @@ -1438,8 +1424,6 @@ int dmasound_init(void) return 0; } -#ifdef MODULE - void dmasound_deinit(void) { if (irq_installed) { @@ -1458,8 +1442,6 @@ void dmasound_deinit(void) unregister_sound_dsp(sq_unit); } -#else /* !MODULE */ - static int dmasound_setup(char *str) { int ints[6], size; @@ -1503,8 +1485,6 @@ static int dmasound_setup(char *str) __setup("dmasound=", dmasound_setup); -#endif /* !MODULE */ - /* * Conversion tables */ @@ -1591,9 +1571,7 @@ char dmasound_alaw2dma8[] = { EXPORT_SYMBOL(dmasound); EXPORT_SYMBOL(dmasound_init); -#ifdef MODULE EXPORT_SYMBOL(dmasound_deinit); -#endif EXPORT_SYMBOL(dmasound_write_sq); EXPORT_SYMBOL(dmasound_catchRadius); #ifdef HAS_8BIT_TABLES Patches currently in stable-queue which might be from rdunlap(a)infradead.org are queue-5.10/sound-oss-dmasound-fix-build-when-drivers-are-mixed-y-m.patch queue-5.10/driver-core-don-t-require-dynamic_debug-for-initcall_debug-probe-timing.patch queue-5.10/ima-allow-fix-uml-builds.patch

1 0

patch for 5.10.stable (sound/oss/dmasound)
by Randy Dunlap 06 May '23

06 May '23

Please apply commit 9dd7c46346ca Author: Randy Dunlap <rdunlap(a)infradead.org> Date: Tue Apr 5 16:41:18 2022 -0700 sound/oss/dmasound: fix build when drivers are mixed =y/=m to the 5.10 stable tree. The kernel test robot <lkp(a)intel.com> reported a build error on 5.10.y and this patch fixes the build error. -- ~Randy

2 1

[PATCH] ALSA: hda/realtek: Add quirk for 2nd ASUS GU603
by Luke D. Jones 06 May '23

06 May '23

Add quirk for GU603 with 0x1c62 variant of codec. Signed-off-by: Luke D. Jones <luke(a)ljones.dev> --- sound/pci/hda/patch_realtek.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 3b9f077a227f..4a585050edc3 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -9501,6 +9501,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x1043, 0x1517, "Asus Zenbook UX31A", ALC269VB_FIXUP_ASUS_ZENBOOK_UX31A), SND_PCI_QUIRK(0x1043, 0x1662, "ASUS GV301QH", ALC294_FIXUP_ASUS_DUAL_SPK), SND_PCI_QUIRK(0x1043, 0x16b2, "ASUS GU603", ALC289_FIXUP_ASUS_GA401), + SND_PCI_QUIRK(0x1043, 0x1c62, "ASUS GU603", ALC289_FIXUP_ASUS_GA401), SND_PCI_QUIRK(0x1043, 0x16e3, "ASUS UX50", ALC269_FIXUP_STEREO_DMIC), SND_PCI_QUIRK(0x1043, 0x1740, "ASUS UX430UA", ALC295_FIXUP_ASUS_DACS), SND_PCI_QUIRK(0x1043, 0x17d1, "ASUS UX431FL", ALC294_FIXUP_ASUS_DUAL_SPK), -- 2.40.0

3 4

[PATCH alsa-lib 0/4] pcm: hw: implement explicit silencing for snd_pcm_drain
by Jaroslav Kysela 05 May '23

05 May '23

This is a complete API solution for the filling of the silence samples for the drain operation. The default bahaviour is to aligns the valid samples to one period with extra silence samples for next 1/10th of second. Introduce SNDRV_PCM_INFO_PERFECT_DRAIN and SNDRV_PCM_HW_PARAMS_NO_DRAIN_SILENCE flags to fully control the filling of the silence samples in the snd_pcm_drain call. Those flags do the bidirectional setup for this operation, so the silencing may be implemented eventually in the kernel space when there's a demand in future. Also, some applications may not require to silence the samples beyond the tail of the ring buffer at all. There is also a new pcm_hw plugin configuration field allowing the overwrite of the default (auto) behaviour. Related: https://lore.kernel.org/alsa-devel/20230420113324.877164-2-oswald.buddenhag… Related: https://lore.kernel.org/alsa-devel/20230405201219.2197789-2-oswald.buddenha… Jaroslav Kysela (4): pcm: hw: setup explicit silencing for snd_pcm_drain by default pcm: hw: add drain_silence configuration keyword pcm: hw: introduce SNDRV_PCM_INFO_PERFECT_DRAIN pcm: hw: introduce SNDRV_PCM_HW_PARAMS_DRAIN_SILENCE include/pcm.h | 1 + include/sound/uapi/asound.h | 4 ++ src/pcm/pcm.c | 88 +++++++++++++++++++++++++++++++------ src/pcm/pcm_hw.c | 74 ++++++++++++++++++++++++++++++- src/pcm/pcm_local.h | 7 +++ 5 files changed, 160 insertions(+), 14 deletions(-) -- 2.39.2

3 16

Added double quotes to variables of three `rm` commands
by GitHub pull_request - opened 05 May '23

05 May '23

alsa-project/alsa-utils pull request #210 was opened from wileyhy: lines 73, 80 and 98 Request URL : https://github.com/alsa-project/alsa-utils/pull/210 Patch URL : https://github.com/alsa-project/alsa-utils/pull/210.patch Repository URL: https://github.com/alsa-project/alsa-utils

1 0

[PATCH 1/7] ALSA: pcm: Revert "ALSA: pcm: rewrite snd_pcm_playback_silence()"
by Oswald Buddenhagen 05 May '23

05 May '23

From: Jaroslav Kysela <perex(a)perex.cz> This reverts commit 9f656705c5faa18afb26d922cfc64f9fd103c38d. There was a regression (in the top-up mode). Unfortunately, the patch provided from the author of this commit is not easy to review. Keep the updated and new comments in headers. Also add a new comment that documents the missed API constraint which led to the regression. Reported-by: Jeff Chua <jeff.chua.linux(a)gmail.com> Link: https://lore.kernel.org/r/CAAJw_ZsbTVd3Es373x_wTNDF7RknGhCD0r+NKUSwAO7HpLAk… Signed-off-by: Jaroslav Kysela <perex(a)perex.cz> Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- v2: - add docu comment - commit message improvements --- sound/core/pcm_lib.c | 90 ++++++++++++++++++++++++----------------- sound/core/pcm_local.h | 3 +- sound/core/pcm_native.c | 6 +-- 3 files changed, 59 insertions(+), 40 deletions(-) diff --git a/sound/core/pcm_lib.c b/sound/core/pcm_lib.c index d21c73944efd..3357ffae635f 100644 --- a/sound/core/pcm_lib.c +++ b/sound/core/pcm_lib.c @@ -42,56 +42,74 @@ static int fill_silence_frames(struct snd_pcm_substream *substream, * * when runtime->silence_size >= runtime->boundary - fill processed area with silence immediately */ -void snd_pcm_playback_silence(struct snd_pcm_substream *substream) +void snd_pcm_playback_silence(struct snd_pcm_substream *substream, snd_pcm_uframes_t new_hw_ptr) { struct snd_pcm_runtime *runtime = substream->runtime; - snd_pcm_uframes_t appl_ptr = READ_ONCE(runtime->control->appl_ptr); - snd_pcm_sframes_t added, hw_avail, frames; - snd_pcm_uframes_t noise_dist, ofs, transfer; + snd_pcm_uframes_t frames, ofs, transfer; int err; - added = appl_ptr - runtime->silence_start; - if (added) { - if (added < 0) - added += runtime->boundary; - if (added < runtime->silence_filled) - runtime->silence_filled -= added; - else - runtime->silence_filled = 0; - runtime->silence_start = appl_ptr; - } - - // This will "legitimately" turn negative on underrun, and will be mangled - // into a huge number by the boundary crossing handling. The initial state - // might also be not quite sane. The code below MUST account for these cases. - hw_avail = appl_ptr - runtime->status->hw_ptr; - if (hw_avail < 0) - hw_avail += runtime->boundary; - - noise_dist = hw_avail + runtime->silence_filled; if (runtime->silence_size < runtime->boundary) { - frames = runtime->silence_threshold - noise_dist; - if (frames <= 0) + snd_pcm_sframes_t noise_dist, n; + snd_pcm_uframes_t appl_ptr = READ_ONCE(runtime->control->appl_ptr); + if (runtime->silence_start != appl_ptr) { + n = appl_ptr - runtime->silence_start; + if (n < 0) + n += runtime->boundary; + if ((snd_pcm_uframes_t)n < runtime->silence_filled) + runtime->silence_filled -= n; + else + runtime->silence_filled = 0; + runtime->silence_start = appl_ptr; + } + if (runtime->silence_filled >= runtime->buffer_size) return; + noise_dist = snd_pcm_playback_hw_avail(runtime) + runtime->silence_filled; + if (noise_dist >= (snd_pcm_sframes_t) runtime->silence_threshold) + return; + frames = runtime->silence_threshold - noise_dist; if (frames > runtime->silence_size) frames = runtime->silence_size; } else { - frames = runtime->buffer_size - noise_dist; - if (frames <= 0) - return; + /* + * This filling mode aims at free-running mode (used for example by dmix), + * which doesn't update the application pointer. + */ + if (new_hw_ptr == ULONG_MAX) { /* initialization */ + snd_pcm_sframes_t avail = snd_pcm_playback_hw_avail(runtime); + if (avail > runtime->buffer_size) + avail = runtime->buffer_size; + runtime->silence_filled = avail > 0 ? avail : 0; + runtime->silence_start = (runtime->status->hw_ptr + + runtime->silence_filled) % + runtime->boundary; + } else { + ofs = runtime->status->hw_ptr; + frames = new_hw_ptr - ofs; + if ((snd_pcm_sframes_t)frames < 0) + frames += runtime->boundary; + runtime->silence_filled -= frames; + if ((snd_pcm_sframes_t)runtime->silence_filled < 0) { + runtime->silence_filled = 0; + runtime->silence_start = new_hw_ptr; + } else { + runtime->silence_start = ofs; + } + } + frames = runtime->buffer_size - runtime->silence_filled; } - if (snd_BUG_ON(frames > runtime->buffer_size)) return; - ofs = (runtime->silence_start + runtime->silence_filled) % runtime->buffer_size; - do { + if (frames == 0) + return; + ofs = runtime->silence_start % runtime->buffer_size; + while (frames > 0) { transfer = ofs + frames > runtime->buffer_size ? runtime->buffer_size - ofs : frames; err = fill_silence_frames(substream, ofs, transfer); snd_BUG_ON(err < 0); runtime->silence_filled += transfer; frames -= transfer; ofs = 0; - } while (frames > 0); + } snd_pcm_dma_buffer_sync(substream, SNDRV_DMA_SYNC_DEVICE); } @@ -425,6 +443,10 @@ static int snd_pcm_update_hw_ptr0(struct snd_pcm_substream *substream, return 0; } + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && + runtime->silence_size > 0) + snd_pcm_playback_silence(substream, new_hw_ptr); + if (in_interrupt) { delta = new_hw_ptr - runtime->hw_ptr_interrupt; if (delta < 0) @@ -442,10 +464,6 @@ static int snd_pcm_update_hw_ptr0(struct snd_pcm_substream *substream, runtime->hw_ptr_wrap += runtime->boundary; } - if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && - runtime->silence_size > 0) - snd_pcm_playback_silence(substream); - update_audio_tstamp(substream, &curr_tstamp, &audio_tstamp); return snd_pcm_update_state(substream, runtime); diff --git a/sound/core/pcm_local.h b/sound/core/pcm_local.h index 42fe3a4e9154..ecb21697ae3a 100644 --- a/sound/core/pcm_local.h +++ b/sound/core/pcm_local.h @@ -29,7 +29,8 @@ int snd_pcm_update_state(struct snd_pcm_substream *substream, struct snd_pcm_runtime *runtime); int snd_pcm_update_hw_ptr(struct snd_pcm_substream *substream); -void snd_pcm_playback_silence(struct snd_pcm_substream *substream); +void snd_pcm_playback_silence(struct snd_pcm_substream *substream, + snd_pcm_uframes_t new_hw_ptr); static inline snd_pcm_uframes_t snd_pcm_avail(struct snd_pcm_substream *substream) diff --git a/sound/core/pcm_native.c b/sound/core/pcm_native.c index 3d0c4a5b701b..94185267a7b9 100644 --- a/sound/core/pcm_native.c +++ b/sound/core/pcm_native.c @@ -958,7 +958,7 @@ static int snd_pcm_sw_params(struct snd_pcm_substream *substream, if (snd_pcm_running(substream)) { if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && runtime->silence_size > 0) - snd_pcm_playback_silence(substream); + snd_pcm_playback_silence(substream, ULONG_MAX); err = snd_pcm_update_state(substream, runtime); } snd_pcm_stream_unlock_irq(substream); @@ -1455,7 +1455,7 @@ static void snd_pcm_post_start(struct snd_pcm_substream *substream, __snd_pcm_set_state(runtime, state); if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && runtime->silence_size > 0) - snd_pcm_playback_silence(substream); + snd_pcm_playback_silence(substream, ULONG_MAX); snd_pcm_timer_notify(substream, SNDRV_TIMER_EVENT_MSTART); } @@ -1916,7 +1916,7 @@ static void snd_pcm_post_reset(struct snd_pcm_substream *substream, runtime->control->appl_ptr = runtime->status->hw_ptr; if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && runtime->silence_size > 0) - snd_pcm_playback_silence(substream); + snd_pcm_playback_silence(substream, ULONG_MAX); snd_pcm_stream_unlock_irq(substream); } -- 2.40.0.152.g15d061e6df

2 10

[PATCH v2 1/7] ALSA: pcm: Revert "ALSA: pcm: rewrite snd_pcm_playback_silence()"
by Oswald Buddenhagen 05 May '23

05 May '23

From: Jaroslav Kysela <perex(a)perex.cz> This reverts commit 9f656705c5faa18afb26d922cfc64f9fd103c38d. There was a regression (in the top-up mode). Unfortunately, the patch provided from the author of this commit is not easy to review. Keep the updated and new comments in headers. Also add a new comment that documents the missed API constraint which led to the regression. Reported-by: Jeff Chua <jeff.chua.linux(a)gmail.com> Link: https://lore.kernel.org/r/CAAJw_ZsbTVd3Es373x_wTNDF7RknGhCD0r+NKUSwAO7HpLAk… Signed-off-by: Jaroslav Kysela <perex(a)perex.cz> Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- v2: - add docu comment - commit message improvements --- sound/core/pcm_lib.c | 90 ++++++++++++++++++++++++----------------- sound/core/pcm_local.h | 3 +- sound/core/pcm_native.c | 6 +-- 3 files changed, 59 insertions(+), 40 deletions(-) diff --git a/sound/core/pcm_lib.c b/sound/core/pcm_lib.c index d21c73944efd..3357ffae635f 100644 --- a/sound/core/pcm_lib.c +++ b/sound/core/pcm_lib.c @@ -42,56 +42,74 @@ static int fill_silence_frames(struct snd_pcm_substream *substream, * * when runtime->silence_size >= runtime->boundary - fill processed area with silence immediately */ -void snd_pcm_playback_silence(struct snd_pcm_substream *substream) +void snd_pcm_playback_silence(struct snd_pcm_substream *substream, snd_pcm_uframes_t new_hw_ptr) { struct snd_pcm_runtime *runtime = substream->runtime; - snd_pcm_uframes_t appl_ptr = READ_ONCE(runtime->control->appl_ptr); - snd_pcm_sframes_t added, hw_avail, frames; - snd_pcm_uframes_t noise_dist, ofs, transfer; + snd_pcm_uframes_t frames, ofs, transfer; int err; - added = appl_ptr - runtime->silence_start; - if (added) { - if (added < 0) - added += runtime->boundary; - if (added < runtime->silence_filled) - runtime->silence_filled -= added; - else - runtime->silence_filled = 0; - runtime->silence_start = appl_ptr; - } - - // This will "legitimately" turn negative on underrun, and will be mangled - // into a huge number by the boundary crossing handling. The initial state - // might also be not quite sane. The code below MUST account for these cases. - hw_avail = appl_ptr - runtime->status->hw_ptr; - if (hw_avail < 0) - hw_avail += runtime->boundary; - - noise_dist = hw_avail + runtime->silence_filled; if (runtime->silence_size < runtime->boundary) { - frames = runtime->silence_threshold - noise_dist; - if (frames <= 0) + snd_pcm_sframes_t noise_dist, n; + snd_pcm_uframes_t appl_ptr = READ_ONCE(runtime->control->appl_ptr); + if (runtime->silence_start != appl_ptr) { + n = appl_ptr - runtime->silence_start; + if (n < 0) + n += runtime->boundary; + if ((snd_pcm_uframes_t)n < runtime->silence_filled) + runtime->silence_filled -= n; + else + runtime->silence_filled = 0; + runtime->silence_start = appl_ptr; + } + if (runtime->silence_filled >= runtime->buffer_size) return; + noise_dist = snd_pcm_playback_hw_avail(runtime) + runtime->silence_filled; + if (noise_dist >= (snd_pcm_sframes_t) runtime->silence_threshold) + return; + frames = runtime->silence_threshold - noise_dist; if (frames > runtime->silence_size) frames = runtime->silence_size; } else { - frames = runtime->buffer_size - noise_dist; - if (frames <= 0) - return; + /* + * This filling mode aims at free-running mode (used for example by dmix), + * which doesn't update the application pointer. + */ + if (new_hw_ptr == ULONG_MAX) { /* initialization */ + snd_pcm_sframes_t avail = snd_pcm_playback_hw_avail(runtime); + if (avail > runtime->buffer_size) + avail = runtime->buffer_size; + runtime->silence_filled = avail > 0 ? avail : 0; + runtime->silence_start = (runtime->status->hw_ptr + + runtime->silence_filled) % + runtime->boundary; + } else { + ofs = runtime->status->hw_ptr; + frames = new_hw_ptr - ofs; + if ((snd_pcm_sframes_t)frames < 0) + frames += runtime->boundary; + runtime->silence_filled -= frames; + if ((snd_pcm_sframes_t)runtime->silence_filled < 0) { + runtime->silence_filled = 0; + runtime->silence_start = new_hw_ptr; + } else { + runtime->silence_start = ofs; + } + } + frames = runtime->buffer_size - runtime->silence_filled; } - if (snd_BUG_ON(frames > runtime->buffer_size)) return; - ofs = (runtime->silence_start + runtime->silence_filled) % runtime->buffer_size; - do { + if (frames == 0) + return; + ofs = runtime->silence_start % runtime->buffer_size; + while (frames > 0) { transfer = ofs + frames > runtime->buffer_size ? runtime->buffer_size - ofs : frames; err = fill_silence_frames(substream, ofs, transfer); snd_BUG_ON(err < 0); runtime->silence_filled += transfer; frames -= transfer; ofs = 0; - } while (frames > 0); + } snd_pcm_dma_buffer_sync(substream, SNDRV_DMA_SYNC_DEVICE); } @@ -425,6 +443,10 @@ static int snd_pcm_update_hw_ptr0(struct snd_pcm_substream *substream, return 0; } + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && + runtime->silence_size > 0) + snd_pcm_playback_silence(substream, new_hw_ptr); + if (in_interrupt) { delta = new_hw_ptr - runtime->hw_ptr_interrupt; if (delta < 0) @@ -442,10 +464,6 @@ static int snd_pcm_update_hw_ptr0(struct snd_pcm_substream *substream, runtime->hw_ptr_wrap += runtime->boundary; } - if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && - runtime->silence_size > 0) - snd_pcm_playback_silence(substream); - update_audio_tstamp(substream, &curr_tstamp, &audio_tstamp); return snd_pcm_update_state(substream, runtime); diff --git a/sound/core/pcm_local.h b/sound/core/pcm_local.h index 42fe3a4e9154..ecb21697ae3a 100644 --- a/sound/core/pcm_local.h +++ b/sound/core/pcm_local.h @@ -29,7 +29,8 @@ int snd_pcm_update_state(struct snd_pcm_substream *substream, struct snd_pcm_runtime *runtime); int snd_pcm_update_hw_ptr(struct snd_pcm_substream *substream); -void snd_pcm_playback_silence(struct snd_pcm_substream *substream); +void snd_pcm_playback_silence(struct snd_pcm_substream *substream, + snd_pcm_uframes_t new_hw_ptr); static inline snd_pcm_uframes_t snd_pcm_avail(struct snd_pcm_substream *substream) diff --git a/sound/core/pcm_native.c b/sound/core/pcm_native.c index 3d0c4a5b701b..94185267a7b9 100644 --- a/sound/core/pcm_native.c +++ b/sound/core/pcm_native.c @@ -958,7 +958,7 @@ static int snd_pcm_sw_params(struct snd_pcm_substream *substream, if (snd_pcm_running(substream)) { if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && runtime->silence_size > 0) - snd_pcm_playback_silence(substream); + snd_pcm_playback_silence(substream, ULONG_MAX); err = snd_pcm_update_state(substream, runtime); } snd_pcm_stream_unlock_irq(substream); @@ -1455,7 +1455,7 @@ static void snd_pcm_post_start(struct snd_pcm_substream *substream, __snd_pcm_set_state(runtime, state); if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && runtime->silence_size > 0) - snd_pcm_playback_silence(substream); + snd_pcm_playback_silence(substream, ULONG_MAX); snd_pcm_timer_notify(substream, SNDRV_TIMER_EVENT_MSTART); } @@ -1916,7 +1916,7 @@ static void snd_pcm_post_reset(struct snd_pcm_substream *substream, runtime->control->appl_ptr = runtime->status->hw_ptr; if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && runtime->silence_size > 0) - snd_pcm_playback_silence(substream); + snd_pcm_playback_silence(substream, ULONG_MAX); snd_pcm_stream_unlock_irq(substream); } -- 2.40.0.152.g15d061e6df

2 7

[PATCH] ALSA: hda/realtek: Fix mute and micmute LEDs for an HP laptop
by Kai-Heng Feng 05 May '23

05 May '23

There's another laptop that needs the fixup to enable mute and micmute LEDs. So do it accordingly. Signed-off-by: Kai-Heng Feng <kai.heng.feng(a)canonical.com> --- sound/pci/hda/patch_realtek.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index f70d6a33421d..afc562a8afbb 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -9478,6 +9478,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x103c, 0x8b8d, "HP", ALC236_FIXUP_HP_GPIO_LED), SND_PCI_QUIRK(0x103c, 0x8b8f, "HP", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED), SND_PCI_QUIRK(0x103c, 0x8b92, "HP", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED), + SND_PCI_QUIRK(0x103c, 0x8b96, "HP", ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF), SND_PCI_QUIRK(0x103c, 0x8bf0, "HP", ALC236_FIXUP_HP_GPIO_LED), SND_PCI_QUIRK(0x1043, 0x103e, "ASUS X540SA", ALC256_FIXUP_ASUS_MIC), SND_PCI_QUIRK(0x1043, 0x103f, "ASUS TX300", ALC282_FIXUP_ASUS_TX300), -- 2.34.1

2 1

[GIT PULL] ASoC fixes for v6.4-rc1
by Mark Brown 05 May '23

05 May '23

The following changes since commit dc801ea8ae37d54706e6f1cef140731ac5981c9c: ASoC: fsl: imx-audmix: remove dummy dai_link->platform (2023-04-21 13:45:07 +0100) are available in the Git repository at: https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git tags/asoc-fix-v6.4-rc1 for you to fetch changes up to ec6f82b4c63cc68f8dc03316e725106d242706be: ASoC: Intel: soc-acpi-cht: Add quirk for Nextbook Ares 8A tablet (2023-05-04 10:14:31 +0900) ---------------------------------------------------------------- ASoC: Fixes for v6.4 A small set of fixes and device quirks that have come in during the merge window, the Qualcomm fix seems quite large but it's mainly code motion so looks larger than it is. ---------------------------------------------------------------- Andrey Rakhmatullin (1): ASoC: amd: yc: Add Asus VivoBook Pro 14 OLED M6400RC to the quirks list for acp6x Enrico Belleri (1): ASoC: amd: yc: Add ASUS M3402RA into DMI table Hans de Goede (2): ASoC: Intel: soc-acpi-byt: Fix "WM510205" match no longer working ASoC: Intel: soc-acpi-cht: Add quirk for Nextbook Ares 8A tablet Krzysztof Kozlowski (1): ASoC: codecs: wcd938x: fix accessing regmap on unattached devices Maxim Kochetkov (1): ASoC: max98090: make it selectable sound/soc/amd/yc/acp6x-mach.c | 14 + sound/soc/codecs/Kconfig | 2 +- sound/soc/codecs/wcd938x-sdw.c | 1037 ++++++++++++++++++++- sound/soc/codecs/wcd938x.c | 1003 +------------------- sound/soc/codecs/wcd938x.h | 1 + sound/soc/intel/common/soc-acpi-intel-byt-match.c | 2 +- sound/soc/intel/common/soc-acpi-intel-cht-match.c | 26 + 7 files changed, 1072 insertions(+), 1013 deletions(-)

2 1

[PATCH 0/5] rewrite snd_pcm_playback_silence() again
by Jaroslav Kysela 05 May '23

05 May '23

This is a split of changes for both patches (the first with the missing top-up mode + later fix with mixups) proposed by Oswald. The aim was to pick only real code changes. Only the first two patches after revert fixes the current silencing issues. The last two are just cleanups with the extra optimization in the last patch moving the common code to a function. Cc: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> Cc: Jeff Chua <jeff.chua.linux(a)gmail.com> Jaroslav Kysela (5): ALSA: pcm: Revert "ALSA: pcm: rewrite snd_pcm_playback_silence()" ALSA: pcm: fix playback silence - use the actual new_hw_ptr for the threshold mode ALSA: pcm: fix playback silence - correct the incremental silencing ALSA: pcm: playback silence - remove extra code ALSA: pcm: playback silence - move silence variables updates to separate function sound/core/pcm_lib.c | 91 +++++++++++++++++++++++++---------------- sound/core/pcm_local.h | 3 +- sound/core/pcm_native.c | 6 +-- 3 files changed, 61 insertions(+), 39 deletions(-) -- 2.39.2

3 11

ucm2: USB-Audio: Add support for ALC4080 Gigabyte Z590 AORUS ULTRA
by GitHub pull_request - edited 05 May '23

05 May '23

alsa-project/alsa-ucm-conf pull request #310 was edited from BearsPunch: When installed Manjaro I had an issue my audio card was not recognized. USB ID is 0414:a00d and as I see you already have it under if.realtek-alc1220-vb condition, but I have ALC4080. So I manually changed USB-Audio.conf under If.realtek-alc4080 condition from (0414:a0(0e|1[0124])) to (0414:a0(0[de]|1[0124])) and now it works perfectly. But Ubuntu (maybe from 22.04) doesn't have this issue. Does Canonical update alsa-ucm-conf by themselves without pull request to main branch? Request URL : https://github.com/alsa-project/alsa-ucm-conf/pull/310 Patch URL : https://github.com/alsa-project/alsa-ucm-conf/pull/310.patch Repository URL: https://github.com/alsa-project/alsa-ucm-conf

1 0

[PATCH v3 0/7] ASoC: mediatek: mt8188: revise AFE driver
by Trevor Wu 05 May '23

05 May '23

The series of patches consists of three major changes. First, remove redundant supply for ADDA DAI dirver. Second, revise ETDM control including APLL dynamic switch via DAPM, so APLL can be enabled when it is really required. Finally, AFE probe function is updated. Bus protection change was dropped at the previous patch because the dependent change was not accepted. Changes since v2: - remove required properties in dt-binding file Changes since v1: - replace unnecessary dev_info with dev_dbg - fix dt-binging ABI breaking behavior Trevor Wu (7): ASoC: mediatek: mt8188: remove supply AUDIO_HIRES ASoC: mediatek: mt8188: complete set_tdm_slot function ASoC: mediatek: mt8188: revise ETDM control flow ASoC: mediatek: mt8188: refine APLL control ASoC: mediatek: mt8188: combine afe component registration ASoC: mediatek: mt8188: add bus protection ASoC: dt-bindings: mediatek,mt8188-afe: add audio properties .../bindings/sound/mediatek,mt8188-afe.yaml | 12 +- sound/soc/mediatek/mt8188/mt8188-afe-clk.c | 138 ++- sound/soc/mediatek/mt8188/mt8188-afe-clk.h | 11 + sound/soc/mediatek/mt8188/mt8188-afe-pcm.c | 113 ++- sound/soc/mediatek/mt8188/mt8188-dai-adda.c | 37 - sound/soc/mediatek/mt8188/mt8188-dai-etdm.c | 922 ++++++++++-------- sound/soc/mediatek/mt8188/mt8188-reg.h | 2 + 7 files changed, 751 insertions(+), 484 deletions(-) -- 2.18.0

3 9

[PATCH] ASoC: da7219: Add Jack insertion detection polarity selection
by David Rau 05 May '23

05 May '23

Add the selection of DA7219 Jack insertion detection polarity - Default polarity (Low) - Inverted polarity (High) Signed-off-by: David Rau <David.Rau.opensource(a)dm.renesas.com> --- sound/soc/codecs/Kconfig | 24 +++++++++++++++++++++++- sound/soc/codecs/da7219-aad.c | 16 ++++++++++++++++ 2 files changed, 39 insertions(+), 1 deletion(-) diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 79d2362ad055..96f934ad52e7 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -967,9 +967,31 @@ config SND_SOC_DA7218 depends on I2C config SND_SOC_DA7219 - tristate + tristate "Dialog DA7219 CODEC" depends on I2C +if SND_SOC_DA7219 + +choice + bool "DA7219 Jack insertion detection polarity selection" + default DA7219_DEFAULT_JACK_INSERTION_POLARITY if (SND_SOC_DA7219) + +config DA7219_DEFAULT_JACK_INSERTION_POLARITY + bool "Default polarity" + depends on SND_SOC_DA7219 + help + Select this option if your DA7219 codec with default Jack insertion detection polarity (Low). + +config DA7219_INVERTED_JACK_INSERTION_POLARITY + bool "Inverted polarity" + depends on SND_SOC_DA7219 + help + Select this option if your DA7219 codec with inverted Jack insertion detection polarity (High). + +endchoice + +endif # SND_SOC_DA7219 + config SND_SOC_DA732X tristate depends on I2C diff --git a/sound/soc/codecs/da7219-aad.c b/sound/soc/codecs/da7219-aad.c index 993a0d00bc48..9d16112cff6b 100644 --- a/sound/soc/codecs/da7219-aad.c +++ b/sound/soc/codecs/da7219-aad.c @@ -879,6 +879,18 @@ static void da7219_aad_handle_gnd_switch_time(struct snd_soc_component *componen } } +static void da7219_aad_handle_polarity(struct snd_soc_component *component) +{ + snd_soc_component_write(component, 0xF0, 0x8B); + + if (IS_ENABLED(CONFIG_DA7219_DEFAULT_JACK_INSERTION_POLARITY)) + snd_soc_component_write(component, 0x75, 0x80); + else if (IS_ENABLED(CONFIG_DA7219_INVERTED_JACK_INSERTION_POLARITY)) + snd_soc_component_write(component, 0x75, 0x00); + + snd_soc_component_write(component, 0xF0, 0x00); +} + /* * Suspend/Resume */ @@ -955,8 +967,12 @@ int da7219_aad_init(struct snd_soc_component *component) snd_soc_component_update_bits(component, DA7219_ACCDET_CONFIG_1, DA7219_BUTTON_CONFIG_MASK, 0); + /* Handle the default ground switch delay time */ da7219_aad_handle_gnd_switch_time(component); + /* Handle the Jack insertion detection polarity */ + da7219_aad_handle_polarity(component); + da7219_aad->aad_wq = create_singlethread_workqueue("da7219-aad"); if (!da7219_aad->aad_wq) { dev_err(component->dev, "Failed to create aad workqueue\n"); -- 2.17.1

3 2

ucm2: USB-Audio: Add support for ALC4080 Gigabyte Z590 AORUS ULTRA
by GitHub pull_request - edited 05 May '23

05 May '23

alsa-project/alsa-ucm-conf pull request #310 was edited from BearsPunch: When I installed Manjaro I had issue that my audio card was not recognized. USB ID is 0414:a00d and as I see you already have it under if.realtek-alc1220-vb condition, but I have ALC4080. So I manually changed USB-Audio.conf under If.realtek-alc4080 condition from (0414:a0(0e|1[0124])) to (0414:a0(0[de]|1[0124])) and now it works perfectly. But Ubuntu (maybe from 22.04) doesn't have this issue. Does Canonical update alsa-ucm-conf by themselves without pull request to main branch? Request URL : https://github.com/alsa-project/alsa-ucm-conf/pull/310 Patch URL : https://github.com/alsa-project/alsa-ucm-conf/pull/310.patch Repository URL: https://github.com/alsa-project/alsa-ucm-conf

1 0

ucm2: USB-Audio: Add support for ALC4080 Gigabyte Z590 AORUS ULTRA
by GitHub pull_request - opened 05 May '23

05 May '23

alsa-project/alsa-ucm-conf pull request #310 was opened from BearsPunch: When I installed Manjaro I had issue that my audio card was not recognized. USB ID is 0414:a00d and as I see you already have it under if.realtek-alc1220-vb condition, but I have ALC4080. So I manually changed USB-Audio.conf under If.realtek-alc4080 condition from (0414:a0(0e|1[0124])) to (0414:a0(0[de]|1[0124])) and now it works perfectly. But Ubuntu (think from 22.04) doesn't have this issue. Does Canonical update alsa-ucm-conf by themselves without pull request to main branch? Request URL : https://github.com/alsa-project/alsa-ucm-conf/pull/310 Patch URL : https://github.com/alsa-project/alsa-ucm-conf/pull/310.patch Repository URL: https://github.com/alsa-project/alsa-ucm-conf

1 0

[PATCH v1 3/5] firmware: tasdevice_fmw: tasdevice firmware loading lib
by Shenghao Ding 04 May '23

04 May '23

Create tasdevice firmware lib. Signed-off-by: Shenghao Ding <13916275206(a)139.com> --- Changes in v1: - Initial Changes to be committed: modified: drivers/firmware/Kconfig modified: drivers/firmware/Makefile new file: drivers/firmware/ti/Kconfig new file: drivers/firmware/ti/Makefile new file: drivers/firmware/ti/tasdevice-fmw.c --- drivers/firmware/Kconfig | 1 + drivers/firmware/Makefile | 1 + drivers/firmware/ti/Kconfig | 5 + drivers/firmware/ti/Makefile | 3 + drivers/firmware/ti/tasdevice-fmw.c | 2380 +++++++++++++++++++++++++++ 5 files changed, 2390 insertions(+) create mode 100644 drivers/firmware/ti/Kconfig create mode 100644 drivers/firmware/ti/Makefile create mode 100644 drivers/firmware/ti/tasdevice-fmw.c diff --git a/drivers/firmware/Kconfig b/drivers/firmware/Kconfig index b59e3041fd62..2d79c35fc102 100644 --- a/drivers/firmware/Kconfig +++ b/drivers/firmware/Kconfig @@ -314,5 +314,6 @@ source "drivers/firmware/psci/Kconfig" source "drivers/firmware/smccc/Kconfig" source "drivers/firmware/tegra/Kconfig" source "drivers/firmware/xilinx/Kconfig" +source "drivers/firmware/ti/Kconfig" endmenu diff --git a/drivers/firmware/Makefile b/drivers/firmware/Makefile index 28fcddcd688f..db41a11374c2 100644 --- a/drivers/firmware/Makefile +++ b/drivers/firmware/Makefile @@ -38,3 +38,4 @@ obj-y += psci/ obj-y += smccc/ obj-y += tegra/ obj-y += xilinx/ +obj-y += ti/ diff --git a/drivers/firmware/ti/Kconfig b/drivers/firmware/ti/Kconfig new file mode 100644 index 000000000000..d92f1d8f776c --- /dev/null +++ b/drivers/firmware/ti/Kconfig @@ -0,0 +1,5 @@ +# SPDX-License-Identifier: GPL-2.0-only + +config FW_TASDEVICE + tristate + default n diff --git a/drivers/firmware/ti/Makefile b/drivers/firmware/ti/Makefile new file mode 100644 index 000000000000..9bdaab94672b --- /dev/null +++ b/drivers/firmware/ti/Makefile @@ -0,0 +1,3 @@ +# SPDX-License-Identifier: GPL-2.0 +# +obj-$(CONFIG_FW_TASDEVICE) += tasdevice-fmw.o diff --git a/drivers/firmware/ti/tasdevice-fmw.c b/drivers/firmware/ti/tasdevice-fmw.c new file mode 100644 index 000000000000..dbab205fc158 --- /dev/null +++ b/drivers/firmware/ti/tasdevice-fmw.c @@ -0,0 +1,2380 @@ +// SPDX-License-Identifier: GPL-2.0 +// +// tasdevice-fmw.c -- TASDEVICE firmware support +// +// Copyright 2023 Texas Instruments, Inc. +// +// Author: Shenghao Ding <shenghao-ding(a)ti.com> + +#include <linux/crc8.h> +#include <linux/firmware.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_gpio.h> +#include <linux/of_irq.h> +#include <linux/regmap.h> +#include <linux/slab.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/tlv.h> +#include <sound/tas2781.h> + + +#define ERROR_PRAM_CRCCHK 0x0000000 +#define ERROR_YRAM_CRCCHK 0x0000001 +#define PPC_DRIVER_CRCCHK 0x00000200 + +#define TAS2781_SA_COEFF_SWAP_REG TASDEVICE_REG(0, 0x35, 0x2c) +#define TAS2781_YRAM_BOOK1 140 +#define TAS2781_YRAM1_PAGE 42 +#define TAS2781_YRAM1_START_REG 88 + +#define TAS2781_YRAM2_START_PAGE 43 +#define TAS2781_YRAM2_END_PAGE 49 +#define TAS2781_YRAM2_START_REG 8 +#define TAS2781_YRAM2_END_REG 127 + +#define TAS2781_YRAM3_PAGE 50 +#define TAS2781_YRAM3_START_REG 8 +#define TAS2781_YRAM3_END_REG 27 + +/*should not include B0_P53_R44-R47 */ +#define TAS2781_YRAM_BOOK2 0 +#define TAS2781_YRAM4_START_PAGE 50 +#define TAS2781_YRAM4_END_PAGE 60 + +#define TAS2781_YRAM5_PAGE 61 +#define TAS2781_YRAM5_START_REG TAS2781_YRAM3_START_REG +#define TAS2781_YRAM5_END_REG TAS2781_YRAM3_END_REG + +#define TASDEVICE_MAXPROGRAM_NUM_KERNEL 5 +#define TASDEVICE_MAXCONFIG_NUM_KERNEL_MULTIPLE_AMPS 64 +#define TASDEVICE_MAXCONFIG_NUM_KERNEL 10 +#define MAIN_ALL_DEVICES_1X 0x01 +#define MAIN_DEVICE_A_1X 0x02 +#define MAIN_DEVICE_B_1X 0x03 +#define MAIN_DEVICE_C_1X 0x04 +#define MAIN_DEVICE_D_1X 0x05 +#define COEFF_DEVICE_A_1X 0x12 +#define COEFF_DEVICE_B_1X 0x13 +#define COEFF_DEVICE_C_1X 0x14 +#define COEFF_DEVICE_D_1X 0x15 +#define PRE_DEVICE_A_1X 0x22 +#define PRE_DEVICE_B_1X 0x23 +#define PRE_DEVICE_C_1X 0x24 +#define PRE_DEVICE_D_1X 0x25 + +struct tas_crc { + unsigned char offset; + unsigned char len; +}; + +const char deviceNumber[TASDEVICE_DSP_TAS_MAX_DEVICE] = { + 1, 2, 1, 2, 1, 1, 0, 2, 4, 3, 1, 2, 3, 4 +}; + +static struct tasdevice_config_info *tasdevice_add_config( + struct tasdevice_priv *tas_priv, unsigned char *config_data, + unsigned int config_size, int *status) +{ + struct tasdevice_config_info *cfg_info; + struct tasdev_blk_data **bk_da; + unsigned int config_offset = 0; + unsigned int i; + + /* In most projects are many audio cases, such as music, handfree, + * receiver, games, audio-to-haptics, PMIC record, bypass mode, + * portrait, landscape, etc. Even in multiple audios, one or + * two of the chips will work for the special case, such as + * ultrasonic application. In order to support these variable-numbers + * of audio cases, flexible configs have been introduced in the + * dsp firmware. + */ + cfg_info = kzalloc(sizeof(struct tasdevice_config_info), GFP_KERNEL); + if (!cfg_info) { + *status = -ENOMEM; + goto out; + } + + if (tas_priv->rcabin.fw_hdr.binary_version_num >= 0x105) { + if (config_offset + 64 > (int)config_size) { + *status = -EINVAL; + dev_err(tas_priv->dev, "add conf: Out of boundary\n"); + goto out; + } + config_offset += 64; + } + + if (config_offset + 4 > (int)config_size) { + *status = -EINVAL; + dev_err(tas_priv->dev, "add config: Out of boundary\n"); + goto out; + } + + /* convert data[offset], data[offset + 1], data[offset + 2] and + * data[offset + 3] into host + */ + cfg_info->nblocks = + be32_to_cpup((__be32 *)&config_data[config_offset]); + config_offset += 4; + + /* Several kinds of dsp/algorithm firmwares can run on tas2781, + * the number and size of blk are not fixed and different among + * these firmwares. + */ + bk_da = cfg_info->blk_data = kcalloc(cfg_info->nblocks, + sizeof(struct tasdev_blk_data *), GFP_KERNEL); + if (!bk_da) { + *status = -ENOMEM; + goto out; + } + cfg_info->real_nblocks = 0; + for (i = 0; i < cfg_info->nblocks; i++) { + if (config_offset + 12 > config_size) { + *status = -EINVAL; + dev_err(tas_priv->dev, + "%s: Out of boundary: i = %d nblocks = %u!\n", + __func__, i, cfg_info->nblocks); + break; + } + bk_da[i] = kzalloc(sizeof(struct tasdev_blk_data), GFP_KERNEL); + if (!bk_da[i]) { + *status = -ENOMEM; + break; + } + + bk_da[i]->dev_idx = config_data[config_offset]; + config_offset++; + + bk_da[i]->block_type = config_data[config_offset]; + config_offset++; + + if (bk_da[i]->block_type == TASDEVICE_BIN_BLK_PRE_POWER_UP) { + if (bk_da[i]->dev_idx == 0) + cfg_info->active_dev = 1; + else + cfg_info->active_dev = 1 << + (bk_da[i]->dev_idx - 1); + + } + bk_da[i]->yram_checksum = + be16_to_cpup((__be16 *)&config_data[config_offset]); + config_offset += 2; + bk_da[i]->block_size = + be32_to_cpup((__be32 *)&config_data[config_offset]); + config_offset += 4; + + bk_da[i]->n_subblks = + be32_to_cpup((__be32 *)&config_data[config_offset]); + + config_offset += 4; + + if (config_offset + bk_da[i]->block_size > config_size) { + *status = -EINVAL; + dev_err(tas_priv->dev, + "%s: Out of boundary: i = %d blks = %u!\n", + __func__, i, cfg_info->nblocks); + break; + } + /* instead of kzalloc+memcpy */ + bk_da[i]->regdata = kmemdup(&config_data[config_offset], + bk_da[i]->block_size, GFP_KERNEL); + if (!bk_da[i]->regdata) { + *status = -ENOMEM; + goto out; + } + + config_offset += bk_da[i]->block_size; + cfg_info->real_nblocks += 1; + } + +out: + return cfg_info; +} + +int tasdevice_rca_parser(void *context, const struct firmware *fmw) +{ + struct tasdevice_priv *tas_priv = context; + struct tasdevice_config_info **cfg_info; + struct tasdevice_rca_hdr *fw_hdr; + struct tasdevice_rca *rca; + unsigned int total_config_sz = 0; + unsigned char *buf; + int offset = 0; + int ret = 0; + int i; + + rca = &(tas_priv->rcabin); + fw_hdr = &(rca->fw_hdr); + if (!fmw || !fmw->data) { + dev_err(tas_priv->dev, "Failed to read %s\n", + tas_priv->rca_binaryname); + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + ret = -EINVAL; + goto out; + } + buf = (unsigned char *)fmw->data; + + fw_hdr->img_sz = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + if (fw_hdr->img_sz != fmw->size) { + dev_err(tas_priv->dev, + "File size not match, %d %u", (int)fmw->size, + fw_hdr->img_sz); + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + ret = -EINVAL; + goto out; + } + + fw_hdr->checksum = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + fw_hdr->binary_version_num = be32_to_cpup((__be32 *)&buf[offset]); + if (fw_hdr->binary_version_num < 0x103) { + dev_err(tas_priv->dev, "File version 0x%04x is too low", + fw_hdr->binary_version_num); + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + ret = -EINVAL; + goto out; + } + offset += 4; + fw_hdr->drv_fw_version = be32_to_cpup((__be32 *)&buf[offset]); + offset += 8; + fw_hdr->plat_type = buf[offset]; + offset += 1; + fw_hdr->dev_family = buf[offset]; + offset += 1; + fw_hdr->reserve = buf[offset]; + offset += 1; + fw_hdr->ndev = buf[offset]; + offset += 1; + if (fw_hdr->ndev != tas_priv->ndev) { + dev_err(tas_priv->dev, + "ndev(%u) in rcabin mismatch ndev(%u) in DTS\n", + fw_hdr->ndev, tas_priv->ndev); + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + ret = -EINVAL; + goto out; + } + if (offset + TASDEVICE_DEVICE_SUM > fw_hdr->img_sz) { + dev_err(tas_priv->dev, "rca_ready: Out of boundary!\n"); + ret = -EINVAL; + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + goto out; + } + + for (i = 0; i < TASDEVICE_DEVICE_SUM; i++, offset++) + fw_hdr->devs[i] = buf[offset]; + + fw_hdr->nconfig = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + + for (i = 0; i < TASDEVICE_CONFIG_SUM; i++) { + fw_hdr->config_size[i] = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + total_config_sz += fw_hdr->config_size[i]; + } + + if (fw_hdr->img_sz - total_config_sz != (unsigned int)offset) { + dev_err(tas_priv->dev, "Bin file error!\n"); + ret = -EINVAL; + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + goto out; + } + + cfg_info = kcalloc(fw_hdr->nconfig, sizeof(*cfg_info), GFP_KERNEL); + if (!cfg_info) { + ret = -ENOMEM; + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + goto out; + } + rca->cfg_info = cfg_info; + rca->ncfgs = 0; + for (i = 0; i < (int)fw_hdr->nconfig; i++) { + rca->ncfgs += 1; + cfg_info[i] = tasdevice_add_config(tas_priv, &buf[offset], + fw_hdr->config_size[i], &ret); + if (ret) { + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + goto out; + } + offset += (int)fw_hdr->config_size[i]; + } +out: + return ret; +} +EXPORT_SYMBOL_NS_GPL(tasdevice_rca_parser, FW_TASDEVICE); + +static int fw_parse_block_data_kernel(struct tasdevice_fw *tas_fmw, + struct tasdev_blk *block, const struct firmware *fmw, int offset) +{ + const unsigned char *data = fmw->data; + + if (offset + 16 > fmw->size) { + dev_err(tas_fmw->dev, "%s: File Size error\n", __func__); + offset = -EINVAL; + goto out; + } + + /* convert data[offset], data[offset + 1], data[offset + 2] and + * data[offset + 3] into host + */ + block->type = be32_to_cpup((__be32 *)&data[offset]); + offset += 4; + + block->is_pchksum_present = data[offset]; + offset++; + + block->pchksum = data[offset]; + offset++; + + block->is_ychksum_present = data[offset]; + offset++; + + block->ychksum = data[offset]; + offset++; + + block->blk_size = be32_to_cpup((__be32 *)&data[offset]); + offset += 4; + + block->nr_subblocks = be32_to_cpup((__be32 *)&data[offset]); + offset += 4; + + if (offset + block->blk_size > fmw->size) { + dev_err(tas_fmw->dev, "%s: nSublocks error\n", __func__); + offset = -EINVAL; + goto out; + } + /* instead of kzalloc+memcpy */ + block->data = kmemdup(&data[offset], block->blk_size, GFP_KERNEL); + if (!block->data) { + offset = -ENOMEM; + goto out; + } + offset += block->blk_size; + +out: + return offset; +} + +static int fw_parse_data_kernel(struct tasdevice_fw *tas_fmw, + struct tasdevice_data *img_data, const struct firmware *fmw, + int offset) +{ + const unsigned char *data = fmw->data; + struct tasdev_blk *blk; + unsigned int i; + + if (offset + 4 > fmw->size) { + dev_err(tas_fmw->dev, "%s: File Size error\n", __func__); + offset = -EINVAL; + goto out; + } + img_data->nr_blk = be32_to_cpup((__be32 *)&data[offset]); + offset += 4; + + img_data->dev_blks = kcalloc(img_data->nr_blk, + sizeof(struct tasdev_blk), GFP_KERNEL); + if (!img_data->dev_blks) { + offset = -ENOMEM; + goto out; + } + + for (i = 0; i < img_data->nr_blk; i++) { + blk = &(img_data->dev_blks[i]); + offset = fw_parse_block_data_kernel(tas_fmw, blk, fmw, offset); + if (offset < 0) { + offset = -EINVAL; + break; + } + } + +out: + return offset; +} + +static int fw_parse_program_data_kernel( + struct tasdevice_priv *tas_priv, struct tasdevice_fw *tas_fmw, + const struct firmware *fmw, int offset) +{ + struct tasdevice_prog *program; + unsigned int i; + + for (i = 0; i < tas_fmw->nr_programs; i++) { + program = &(tas_fmw->programs[i]); + if (offset + 72 > fmw->size) { + dev_err(tas_priv->dev, "%s: mpName error\n", __func__); + offset = -EINVAL; + goto out; + } + /*skip 72 unused byts*/ + offset += 72; + + offset = fw_parse_data_kernel(tas_fmw, &(program->dev_data), + fmw, offset); + if (offset < 0) + goto out; + } + +out: + return offset; +} + +static int fw_parse_configuration_data_kernel( + struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, const struct firmware *fmw, int offset) +{ + const unsigned char *data = fmw->data; + struct tasdevice_config *config; + unsigned int i; + + for (i = 0; i < tas_fmw->nr_configurations; i++) { + config = &(tas_fmw->configs[i]); + if (offset + 80 > fmw->size) { + dev_err(tas_priv->dev, "%s: mpName error\n", __func__); + offset = -EINVAL; + goto out; + } + memcpy(config->name, &data[offset], 64); + /*skip extra 16 bytes*/ + offset += 80; + + offset = fw_parse_data_kernel(tas_fmw, &(config->dev_data), + fmw, offset); + if (offset < 0) + goto out; + } + +out: + return offset; +} + +static int fw_parse_variable_header_kernel( + struct tasdevice_priv *tas_priv, const struct firmware *fmw, + int offset) +{ + struct tasdevice_fw *tas_fmw = tas_priv->fmw; + struct tasdevice_dspfw_hdr *fw_hdr = &(tas_fmw->fw_hdr); + struct tasdevice_prog *program; + struct tasdevice_config *config; + const unsigned char *buf = fmw->data; + unsigned short max_confs; + unsigned int i; + + if (offset + 12 + 4 * TASDEVICE_MAXPROGRAM_NUM_KERNEL > fmw->size) { + dev_err(tas_priv->dev, "%s: File Size error\n", __func__); + offset = -EINVAL; + goto out; + } + fw_hdr->device_family = be16_to_cpup((__be16 *)&buf[offset]); + if (fw_hdr->device_family != 0) { + dev_err(tas_priv->dev, "%s:not TAS device\n", __func__); + offset = -EINVAL; + goto out; + } + offset += 2; + fw_hdr->device = be16_to_cpup((__be16 *)&buf[offset]); + if (fw_hdr->device >= TASDEVICE_DSP_TAS_MAX_DEVICE || + fw_hdr->device == 6) { + dev_err(tas_priv->dev, "Unsupported dev %d\n", fw_hdr->device); + offset = -EINVAL; + goto out; + } + offset += 2; + fw_hdr->ndev = deviceNumber[fw_hdr->device]; + + if (fw_hdr->ndev != tas_priv->ndev) { + dev_err(tas_priv->dev, + "%s: ndev(%u) in dspbin mismatch ndev(%u) in DTS\n", + __func__, fw_hdr->ndev, tas_priv->ndev); + offset = -EINVAL; + goto out; + } + + tas_fmw->nr_programs = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + + if (tas_fmw->nr_programs == 0 || tas_fmw->nr_programs > + TASDEVICE_MAXPROGRAM_NUM_KERNEL) { + dev_err(tas_priv->dev, "mnPrograms is invalid\n"); + offset = -EINVAL; + goto out; + } + + tas_fmw->programs = kcalloc(tas_fmw->nr_programs, + sizeof(struct tasdevice_prog), GFP_KERNEL); + if (!tas_fmw->programs) { + offset = -ENOMEM; + goto out; + } + + for (i = 0; i < tas_fmw->nr_programs; i++) { + program = &(tas_fmw->programs[i]); + program->prog_size = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + } + + /* Skip the unused prog_size */ + offset += 4 * (TASDEVICE_MAXPROGRAM_NUM_KERNEL - tas_fmw->nr_programs); + + tas_fmw->nr_configurations = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + + /* The max number of config in firmware greater than 4 pieces of + * tas2781s is different from the one lower than 4 pieces of + * tas2781s. + */ + max_confs = (fw_hdr->ndev >= 4) ? + TASDEVICE_MAXCONFIG_NUM_KERNEL_MULTIPLE_AMPS : + TASDEVICE_MAXCONFIG_NUM_KERNEL; + if (tas_fmw->nr_configurations == 0 || + tas_fmw->nr_configurations > max_confs) { + dev_err(tas_priv->dev, "%s: Conf is invalid\n", __func__); + offset = -EINVAL; + goto out; + } + + if (offset + 4 * max_confs > fmw->size) { + dev_err(tas_priv->dev, "%s: mpConfigurations err\n", __func__); + offset = -EINVAL; + goto out; + } + + tas_fmw->configs = kcalloc(tas_fmw->nr_configurations, + sizeof(struct tasdevice_config), GFP_KERNEL); + if (!tas_fmw->configs) { + offset = -ENOMEM; + goto out; + } + + for (i = 0; i < tas_fmw->nr_programs; i++) { + config = &(tas_fmw->configs[i]); + config->cfg_size = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + } + + /* Skip the unused configs */ + offset += 4 * (max_confs - tas_fmw->nr_programs); + +out: + return offset; +} + +static int tasdevice_process_block(void *context, unsigned char *data, + unsigned char dev_idx, int sublocksize) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)context; + int subblk_offset, chn, chnend, rc; + unsigned char subblk_typ = data[1]; + int blktyp = dev_idx & 0xC0; + int idx = dev_idx & 0x3F; + bool is_err = false; + + if (idx) { + chn = idx - 1; + chnend = idx; + } else { + if (tas_priv->set_global_mode) { + chn = tas_priv->ndev; + chnend = tas_priv->ndev + 1; + } else { + chn = 0; + chnend = tas_priv->ndev; + } + } + + for (; chn < chnend; chn++) { + if (!tas_priv->set_global_mode && + tas_priv->tasdevice[chn].is_loading == false) + continue; + + is_err = false; + subblk_offset = 2; + switch (subblk_typ) { + case TASDEVICE_CMD_SING_W: { + int i; + unsigned short len = be16_to_cpup((__be16 *)&data[2]); + + subblk_offset += 2; + if (subblk_offset + 4 * len > sublocksize) { + dev_err(tas_priv->dev, + "process_block: Out of boundary\n"); + is_err = true; + break; + } + + for (i = 0; i < len; i++) { + rc = tasdevice_dev_write(tas_priv, chn, + TASDEVICE_REG(data[subblk_offset], + data[subblk_offset + 1], + data[subblk_offset + 2]), + data[subblk_offset + 3]); + if (rc < 0) { + is_err = true; + dev_err(tas_priv->dev, + "process_block: single write error\n"); + } + subblk_offset += 4; + } + } + break; + case TASDEVICE_CMD_BURST: { + unsigned short len = be16_to_cpup((__be16 *)&data[2]); + + subblk_offset += 2; + if (subblk_offset + 4 + len > sublocksize) { + dev_err(tas_priv->dev, + "%s: BST Out of boundary\n", + __func__); + is_err = true; + break; + } + if (len % 4) { + dev_err(tas_priv->dev, + "%s:Bst-len(%u)not div by 4\n", + __func__, len); + break; + } + + rc = tasdevice_dev_bulk_write(tas_priv, chn, + TASDEVICE_REG(data[subblk_offset], + data[subblk_offset + 1], + data[subblk_offset + 2]), + &(data[subblk_offset + 4]), len); + if (rc < 0) { + is_err = true; + dev_err(tas_priv->dev, + "%s: bulk_write error = %d\n", + __func__, rc); + } + subblk_offset += (len + 4); + } + break; + case TASDEVICE_CMD_DELAY: { + unsigned int sleep_time = 0; + + if (subblk_offset + 2 > sublocksize) { + dev_err(tas_priv->dev, + "%s: delay Out of boundary\n", + __func__); + is_err = true; + break; + } + sleep_time = be16_to_cpup((__be16 *)&data[2]) * 1000; + usleep_range(sleep_time, sleep_time + 50); + subblk_offset += 2; + } + break; + case TASDEVICE_CMD_FIELD_W: + if (subblk_offset + 6 > sublocksize) { + dev_err(tas_priv->dev, + "%s: bit write Out of boundary\n", + __func__); + is_err = true; + break; + } + rc = tasdevice_dev_update_bits(tas_priv, chn, + TASDEVICE_REG(data[subblk_offset + 2], + data[subblk_offset + 3], + data[subblk_offset + 4]), + data[subblk_offset + 1], + data[subblk_offset + 5]); + if (rc < 0) { + is_err = true; + dev_err(tas_priv->dev, + "%s: update_bits error = %d\n", + __func__, rc); + } + subblk_offset += 6; + break; + default: + break; + } + if (is_err == true && blktyp != 0) { + if (blktyp == 0x80) { + tas_priv->tasdevice[chn].cur_prog = -1; + tas_priv->tasdevice[chn].cur_conf = -1; + } else + tas_priv->tasdevice[chn].cur_conf = -1; + } + } + + return subblk_offset; +} + +void tasdevice_select_cfg_blk(void *pContext, int conf_no, + unsigned char block_type) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) pContext; + struct tasdevice_rca *rca = &(tas_priv->rcabin); + struct tasdevice_config_info **cfg_info = rca->cfg_info; + struct tasdev_blk_data **blk_data; + int j, k, chn, chnend; + + if (conf_no >= rca->ncfgs || conf_no < 0 || !cfg_info) { + dev_err(tas_priv->dev, "conf_no should be not more than %u\n", + rca->ncfgs); + return; + } + blk_data = cfg_info[conf_no]->blk_data; + + for (j = 0; j < (int)cfg_info[conf_no]->real_nblocks; j++) { + unsigned int length = 0, rc = 0; + + if (block_type > 5 || block_type < 2) { + dev_err(tas_priv->dev, + "block_type should be in range from 2 to 5\n"); + break; + } + if (block_type != blk_data[j]->block_type) + continue; + + for (k = 0; k < (int)blk_data[j]->n_subblks; k++) { + if (blk_data[j]->dev_idx) { + chn = blk_data[j]->dev_idx - 1; + chnend = blk_data[j]->dev_idx; + } else { + chn = 0; + chnend = tas_priv->ndev; + } + for (; chn < chnend; chn++) + tas_priv->tasdevice[chn].is_loading = true; + + rc = tasdevice_process_block(tas_priv, + blk_data[j]->regdata + length, + blk_data[j]->dev_idx, + blk_data[j]->block_size - length); + length += rc; + if (blk_data[j]->block_size < length) { + dev_err(tas_priv->dev, + "%s: %u %u out of boundary\n", + __func__, length, + blk_data[j]->block_size); + break; + } + } + if (length != blk_data[j]->block_size) + dev_err(tas_priv->dev, "%s: %u %u size is not same\n", + __func__, length, blk_data[j]->block_size); + } +} +EXPORT_SYMBOL_NS_GPL(tasdevice_select_cfg_blk, FW_TASDEVICE); + +static int tasdevice_load_block_kernel( + struct tasdevice_priv *tasdevice, struct tasdev_blk *block) +{ + struct tasdevice_dspfw_hdr *fw_hdr = &(tasdevice->fmw->fw_hdr); + struct tasdevice_fw_fixed_hdr *fw_fixed_hdr = &(fw_hdr->fixed_hdr); + const unsigned int blk_size = block->blk_size; + unsigned int i, length; + unsigned char *data = block->data; + unsigned char dev_idx = 0; + + if (fw_fixed_hdr->ppcver >= PPC3_VERSION) { + switch (block->type) { + case MAIN_ALL_DEVICES_1X: + dev_idx = 0x80; + break; + case MAIN_DEVICE_A_1X: + dev_idx = 0x81; + break; + case COEFF_DEVICE_A_1X: + case PRE_DEVICE_A_1X: + dev_idx = 0xC1; + break; + case MAIN_DEVICE_B_1X: + dev_idx = 0x82; + break; + case COEFF_DEVICE_B_1X: + case PRE_DEVICE_B_1X: + dev_idx = 0xC2; + break; + case MAIN_DEVICE_C_1X: + dev_idx = 0x83; + break; + case COEFF_DEVICE_C_1X: + case PRE_DEVICE_C_1X: + dev_idx = 0xC3; + break; + case MAIN_DEVICE_D_1X: + dev_idx = 0x84; + break; + case COEFF_DEVICE_D_1X: + case PRE_DEVICE_D_1X: + dev_idx = 0xC4; + break; + default: + dev_info(tasdevice->dev, + "%s: load block: Other Type = 0x%02x\n", + __func__, block->type); + break; + } + } else { + switch (block->type) { + case MAIN_ALL_DEVICES: + dev_idx = 0|0x80; + break; + case MAIN_DEVICE_A: + dev_idx = 0x81; + break; + case COEFF_DEVICE_A: + case PRE_DEVICE_A: + dev_idx = 0xC1; + break; + case MAIN_DEVICE_B: + dev_idx = 0x82; + break; + case COEFF_DEVICE_B: + case PRE_DEVICE_B: + dev_idx = 0xC2; + break; + case MAIN_DEVICE_C: + dev_idx = 0x83; + break; + case COEFF_DEVICE_C: + case PRE_DEVICE_C: + dev_idx = 0xC3; + break; + case MAIN_DEVICE_D: + dev_idx = 0x84; + break; + case COEFF_DEVICE_D: + case PRE_DEVICE_D: + dev_idx = 0xC4; + break; + default: + dev_info(tasdevice->dev, + "%s: load block: Other Type = 0x%02x\n", + __func__, block->type); + break; + } + } + + for (i = 0, length = 0; i < block->nr_subblocks; i++) { + int rc = tasdevice_process_block(tasdevice, data + length, + dev_idx, blk_size - length); + if (rc < 0) { + dev_err(tasdevice->dev, + "%s: %u %u sublock write error\n", + __func__, length, blk_size); + break; + } + length += (unsigned int)rc; + if (blk_size < length) { + dev_err(tasdevice->dev, "%s: %u %u out of boundary\n", + __func__, length, blk_size); + break; + } + } + + return 0; +} + +static int fw_parse_variable_hdr(struct tasdevice_priv + *tas_priv, struct tasdevice_dspfw_hdr *fw_hdr, + const struct firmware *fmw, int offset) +{ + const unsigned char *buf = fmw->data; + int len = strlen((char *)&buf[offset]); + + len++; + + if (offset + len + 8 > fmw->size) { + dev_err(tas_priv->dev, "%s: File Size error\n", __func__); + offset = -EINVAL; + goto out; + } + + offset += len; + + fw_hdr->device_family = be32_to_cpup((__be32 *)&buf[offset]); + if (fw_hdr->device_family != 0) { + dev_err(tas_priv->dev, "%s: not TAS device\n", __func__); + offset = -EINVAL; + goto out; + } + offset += 4; + + fw_hdr->device = be32_to_cpup((__be32 *)&buf[offset]); + if (fw_hdr->device >= TASDEVICE_DSP_TAS_MAX_DEVICE || + fw_hdr->device == 6) { + dev_err(tas_priv->dev, "Unsupported dev %d\n", fw_hdr->device); + offset = -EINVAL; + goto out; + } + offset += 4; + fw_hdr->ndev = deviceNumber[fw_hdr->device]; + +out: + return offset; +} + +static int fw_parse_variable_header_git(struct tasdevice_priv + *tas_priv, const struct firmware *fmw, int offset) +{ + struct tasdevice_fw *tas_fmw = tas_priv->fmw; + struct tasdevice_dspfw_hdr *fw_hdr = &(tas_fmw->fw_hdr); + + offset = fw_parse_variable_hdr(tas_priv, fw_hdr, fmw, offset); + if (offset < 0) + goto out; + if (fw_hdr->ndev != tas_priv->ndev) { + dev_err(tas_priv->dev, + "%s: ndev(%u) in dspbin mismatch ndev(%u) in DTS\n", + __func__, fw_hdr->ndev, tas_priv->ndev); + offset = -EINVAL; + } + +out: + return offset; +} + +static int fw_parse_block_data(struct tasdevice_fw *tas_fmw, + struct tasdev_blk *block, const struct firmware *fmw, int offset) +{ + unsigned char *data = (unsigned char *)fmw->data; + int n; + + if (offset + 8 > fmw->size) { + dev_err(tas_fmw->dev, "%s: Type error\n", __func__); + offset = -EINVAL; + goto out; + } + block->type = be32_to_cpup((__be32 *)&data[offset]); + offset += 4; + + if (tas_fmw->fw_hdr.fixed_hdr.drv_ver >= PPC_DRIVER_CRCCHK) { + if (offset + 8 > fmw->size) { + dev_err(tas_fmw->dev, "PChkSumPresent error\n"); + offset = -EINVAL; + goto out; + } + block->is_pchksum_present = data[offset]; + offset++; + + block->pchksum = data[offset]; + offset++; + + block->is_ychksum_present = data[offset]; + offset++; + + block->ychksum = data[offset]; + offset++; + } else { + block->is_pchksum_present = 0; + block->is_ychksum_present = 0; + } + + block->nr_cmds = be32_to_cpup((__be32 *)&data[offset]); + offset += 4; + + n = block->nr_cmds * 4; + if (offset + n > fmw->size) { + dev_err(tas_fmw->dev, + "%s: File Size(%lu) error offset = %d n = %d\n", + __func__, (unsigned long)fmw->size, offset, n); + offset = -EINVAL; + goto out; + } + /* instead of kzalloc+memcpy */ + block->data = kmemdup(&data[offset], n, GFP_KERNEL); + if (!block->data) { + offset = -ENOMEM; + goto out; + } + offset += n; + +out: + return offset; +} + +/* When parsing error occurs, all the memory resource will be released + * in the end of tasdevice_rca_ready. + */ +static int fw_parse_data(struct tasdevice_fw *tas_fmw, + struct tasdevice_data *img_data, const struct firmware *fmw, + int offset) +{ + const unsigned char *data = (unsigned char *)fmw->data; + struct tasdev_blk *blk; + unsigned int i; + int n; + + if (offset + 64 > fmw->size) { + dev_err(tas_fmw->dev, "%s: Name error\n", __func__); + offset = -EINVAL; + goto out; + } + memcpy(img_data->name, &data[offset], 64); + offset += 64; + + n = strlen((char *)&data[offset]); + n++; + if (offset + n + 2 > fmw->size) { + dev_err(tas_fmw->dev, "%s: Description error\n", __func__); + offset = -EINVAL; + goto out; + } + offset += n; + img_data->nr_blk = be16_to_cpup((__be16 *)&data[offset]); + offset += 2; + + img_data->dev_blks = kcalloc(img_data->nr_blk, + sizeof(struct tasdev_blk), GFP_KERNEL); + if (!img_data->dev_blks) { + offset = -ENOMEM; + goto out; + } + for (i = 0; i < img_data->nr_blk; i++) { + blk = &(img_data->dev_blks[i]); + offset = fw_parse_block_data(tas_fmw, blk, fmw, offset); + if (offset < 0) { + offset = -EINVAL; + goto out; + } + } + +out: + return offset; +} + +/* When parsing error occurs, all the memory resource will be released + * in the end of tasdevice_rca_ready. + */ +static int fw_parse_program_data(struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, const struct firmware *fmw, int offset) +{ + unsigned char *buf = (unsigned char *)fmw->data; + struct tasdevice_prog *program; + int i; + + if (offset + 2 > fmw->size) { + dev_err(tas_priv->dev, "%s: File Size error\n", __func__); + offset = -EINVAL; + goto out; + } + tas_fmw->nr_programs = be16_to_cpup((__be16 *)&buf[offset]); + offset += 2; + + if (tas_fmw->nr_programs == 0) { + /*Not error in calibration Data file, return directly*/ + dev_info(tas_priv->dev, "%s: No Programs data, maybe calbin\n", + __func__); + goto out; + } + + tas_fmw->programs = + kcalloc(tas_fmw->nr_programs, sizeof(struct tasdevice_prog), + GFP_KERNEL); + if (!tas_fmw->programs) { + offset = -ENOMEM; + goto out; + } + for (i = 0; i < tas_fmw->nr_programs; i++) { + int n = 0; + + program = &(tas_fmw->programs[i]); + if (offset + 64 > fmw->size) { + dev_err(tas_priv->dev, "%s: mpName error\n", __func__); + offset = -EINVAL; + goto out; + } + offset += 64; + + n = strlen((char *)&buf[offset]); + /* skip '\0' and 5 unused bytes */ + n += 6; + if (offset + n > fmw->size) { + dev_err(tas_priv->dev, "Description err\n"); + offset = -EINVAL; + goto out; + } + + offset += n; + + offset = fw_parse_data(tas_fmw, &(program->dev_data), fmw, + offset); + if (offset < 0) + goto out; + } + +out: + return offset; +} + +/* When parsing error occurs, all the memory resource will be released + * in the end of tasdevice_rca_ready. + */ +static int fw_parse_configuration_data( + struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, + const struct firmware *fmw, int offset) +{ + unsigned char *data = (unsigned char *)fmw->data; + struct tasdevice_config *config; + unsigned int i; + int n; + + if (offset + 2 > fmw->size) { + dev_err(tas_priv->dev, "%s: File Size error\n", __func__); + offset = -EINVAL; + goto out; + } + tas_fmw->nr_configurations = be16_to_cpup((__be16 *)&data[offset]); + offset += 2; + + if (tas_fmw->nr_configurations == 0) { + dev_err(tas_priv->dev, "%s: Conf is zero\n", __func__); + /*Not error for calibration Data file, return directly*/ + goto out; + } + tas_fmw->configs = kcalloc(tas_fmw->nr_configurations, + sizeof(struct tasdevice_config), GFP_KERNEL); + if (!tas_fmw->configs) { + offset = -ENOMEM; + goto out; + } + for (i = 0; i < tas_fmw->nr_configurations; i++) { + config = &(tas_fmw->configs[i]); + if (offset + 64 > fmw->size) { + dev_err(tas_priv->dev, "File Size err\n"); + offset = -EINVAL; + goto out; + } + memcpy(config->name, &data[offset], 64); + offset += 64; + + n = strlen((char *)&data[offset]); + n += 15; + if (offset + n > fmw->size) { + dev_err(tas_priv->dev, "Description err\n"); + offset = -EINVAL; + goto out; + } + + offset += n; + + offset = fw_parse_data(tas_fmw, &(config->dev_data), + fmw, offset); + if (offset < 0) + goto out; + } + +out: + return offset; +} + +static bool check_inpage_yram_rg(struct tas_crc *cd, + unsigned char reg, unsigned char len) +{ + bool in = false; + + + if (reg <= TAS2781_YRAM5_END_REG && + reg >= TAS2781_YRAM5_START_REG) { + if (reg + len > TAS2781_YRAM5_END_REG) + cd->len = TAS2781_YRAM5_END_REG - reg + 1; + else + cd->len = len; + cd->offset = reg; + in = true; + } else if (reg < TAS2781_YRAM5_START_REG) { + if (reg + len > TAS2781_YRAM5_START_REG) { + cd->offset = TAS2781_YRAM5_START_REG; + cd->len = len - TAS2781_YRAM5_START_REG + reg; + in = true; + } + } + + return in; +} + +static bool check_inpage_yram_bk1(struct tas_crc *cd, + unsigned char page, unsigned char reg, unsigned char len) +{ + bool in = false; + + if (page == TAS2781_YRAM1_PAGE) { + if (reg >= TAS2781_YRAM1_START_REG) { + cd->offset = reg; + cd->len = len; + in = true; + } else if (reg + len > TAS2781_YRAM1_START_REG) { + cd->offset = TAS2781_YRAM1_START_REG; + cd->len = len - TAS2781_YRAM1_START_REG + reg; + in = true; + } + } else if (page == TAS2781_YRAM3_PAGE) + in = check_inpage_yram_rg(cd, reg, len); + + return in; +} + +/* Return Code: + * true -- the registers are in the inpage yram + * false -- the registers are NOT in the inpage yram + */ +static bool check_inpage_yram(struct tas_crc *cd, unsigned char book, + unsigned char page, unsigned char reg, unsigned char len) +{ + bool in = false; + + if (book == TAS2781_YRAM_BOOK1) { + in = check_inpage_yram_bk1(cd, page, reg, len); + goto end; + } + if (book == TAS2781_YRAM_BOOK2 && page == TAS2781_YRAM5_PAGE) + in = check_inpage_yram_rg(cd, reg, len); + +end: + return in; +} + +static bool check_inblock_yram_bk(struct tas_crc *cd, + unsigned char page, unsigned char reg, unsigned char len) +{ + bool in = false; + + if ((page >= TAS2781_YRAM4_START_PAGE && + page <= TAS2781_YRAM4_END_PAGE) || + (page >= TAS2781_YRAM2_START_PAGE && + page <= TAS2781_YRAM2_END_PAGE)) { + if (reg <= TAS2781_YRAM2_END_REG && + reg >= TAS2781_YRAM2_START_REG) { + cd->offset = reg; + cd->len = len; + in = true; + } else if (reg < TAS2781_YRAM2_START_REG) { + if (reg + len - 1 >= TAS2781_YRAM2_START_REG) { + cd->offset = TAS2781_YRAM2_START_REG; + cd->len = reg + len - TAS2781_YRAM2_START_REG; + in = true; + } + } + } + + return in; +} + +/* Return Code: + * true -- the registers are in the inblock yram + * false -- the registers are NOT in the inblock yram + */ +static bool check_inblock_yram(struct tas_crc *cd, unsigned char book, + unsigned char page, unsigned char reg, unsigned char len) +{ + bool in = false; + + if (book == TAS2781_YRAM_BOOK1 || book == TAS2781_YRAM_BOOK2) + in = check_inblock_yram_bk(cd, page, reg, len); + + return in; +} + +static bool check_yram(struct tas_crc *cd, unsigned char book, + unsigned char page, unsigned char reg, unsigned char len) +{ + bool in; + + in = check_inpage_yram(cd, book, page, reg, len); + if (in) + goto end; + in = check_inblock_yram(cd, book, page, reg, len); + +end: + return in; +} + +static int tasdev_multibytes_chksum(struct tasdevice_priv *tasdevice, + enum channel chn, unsigned char book, unsigned char page, + unsigned char reg, unsigned int len) +{ + struct tas_crc crc_data; + unsigned char crc_chksum = 0; + unsigned char nBuf1[128]; + int ret = 0; + int i; + bool in; + + if ((reg + len - 1) > 127) { + ret = -EINVAL; + dev_err(tasdevice->dev, "firmware error\n"); + goto end; + } + + if ((book == TASDEVICE_BOOK_ID(TAS2781_SA_COEFF_SWAP_REG)) + && (page == TASDEVICE_PAGE_ID(TAS2781_SA_COEFF_SWAP_REG)) + && (reg == TASDEVICE_PAGE_REG(TAS2781_SA_COEFF_SWAP_REG)) + && (len == 4)) { + /*DSP swap command, pass */ + ret = 0; + goto end; + } + + in = check_yram(&crc_data, book, page, reg, len); + if (!in) + goto end; + + if (len == 1) { + dev_err(tasdevice->dev, "firmware error\n"); + ret = -EINVAL; + goto end; + } + + ret = tasdevice_dev_bulk_read(tasdevice, chn, + TASDEVICE_REG(book, page, crc_data.offset), + nBuf1, crc_data.len); + if (ret < 0) + goto end; + + for (i = 0; i < crc_data.len; i++) { + if ((book == TASDEVICE_BOOK_ID(TAS2781_SA_COEFF_SWAP_REG)) + && (page == TASDEVICE_PAGE_ID( + TAS2781_SA_COEFF_SWAP_REG)) + && ((i + crc_data.offset) + >= TASDEVICE_PAGE_REG(TAS2781_SA_COEFF_SWAP_REG)) + && ((i + crc_data.offset) + <= (TASDEVICE_PAGE_REG(TAS2781_SA_COEFF_SWAP_REG) + + 4))) + /*DSP swap command, bypass */ + continue; + else + crc_chksum += crc8(tasdevice->crc8_lkp_tbl, &nBuf1[i], + 1, 0); + } + + ret = crc_chksum; + +end: + return ret; +} + +static int do_singlereg_checksum(struct tasdevice_priv *tasdevice, + enum channel chl, unsigned char book, unsigned char page, + unsigned char reg, unsigned char val) +{ + struct tas_crc crc_data; + unsigned int nData1; + int ret = 0; + bool in; + + if ((book == TASDEVICE_BOOK_ID(TAS2781_SA_COEFF_SWAP_REG)) + && (page == TASDEVICE_PAGE_ID(TAS2781_SA_COEFF_SWAP_REG)) + && (reg >= TASDEVICE_PAGE_REG(TAS2781_SA_COEFF_SWAP_REG)) + && (reg <= (TASDEVICE_PAGE_REG( + TAS2781_SA_COEFF_SWAP_REG) + 4))) { + /*DSP swap command, pass */ + ret = 0; + goto end; + } + + in = check_yram(&crc_data, book, page, reg, 1); + if (!in) + goto end; + ret = tasdevice_dev_read(tasdevice, chl, + TASDEVICE_REG(book, page, reg), &nData1); + if (ret < 0) + goto end; + + if (nData1 != val) { + dev_err(tasdevice->dev, + "B[0x%x]P[0x%x]R[0x%x] W[0x%x], R[0x%x]\n", + book, page, reg, val, nData1); + tasdevice->tasdevice[chl].err_code |= ERROR_YRAM_CRCCHK; + ret = -EAGAIN; + goto end; + } + + ret = crc8(tasdevice->crc8_lkp_tbl, &val, 1, 0); + +end: + return ret; +} + +static void set_err_prg_cfg(unsigned int type, struct tasdevice *dev) +{ + if ((type == MAIN_ALL_DEVICES) || (type == MAIN_DEVICE_A) + || (type == MAIN_DEVICE_B) || (type == MAIN_DEVICE_C) + || (type == MAIN_DEVICE_D)) + dev->cur_prog = -1; + else + dev->cur_conf = -1; +} + +static int tasdev_bytes_chksum(struct tasdevice_priv *tas_priv, + struct tasdev_blk *block, int chn, unsigned char book, + unsigned char page, unsigned char reg, unsigned int len, + unsigned char val, unsigned char *crc_chksum) +{ + int ret; + + if (len > 1) + ret = tasdev_multibytes_chksum(tas_priv, chn, book, page, reg, + len); + else + ret = do_singlereg_checksum(tas_priv, chn, book, page, reg, + val); + + if (ret > 0) { + *crc_chksum += (unsigned char)ret; + goto end; + } + + if (ret != -EAGAIN) + goto end; + + block->nr_retry--; + if (block->nr_retry > 0) + goto end; + + set_err_prg_cfg(block->type, &tas_priv->tasdevice[chn]); + +end: + return ret; +} + +static int tasdev_multibytes_wr(struct tasdevice_priv *tas_priv, + struct tasdev_blk *block, int chn, unsigned char book, + unsigned char page, unsigned char reg, unsigned char *data, + unsigned int len, unsigned int *nr_cmds, + unsigned char *crc_chksum) +{ + int ret; + + if (len > 1) { + ret = tasdevice_dev_bulk_write(tas_priv, chn, + TASDEVICE_REG(book, page, reg), data + 3, len); + if (ret < 0) + goto end; + if (block->is_ychksum_present) + ret = tasdev_bytes_chksum(tas_priv, block, chn, + book, page, reg, len, 0, crc_chksum); + } else { + ret = tasdevice_dev_write(tas_priv, chn, + TASDEVICE_REG(book, page, reg), data[3]); + if (ret < 0) + goto end; + if (block->is_ychksum_present) + ret = tasdev_bytes_chksum(tas_priv, block, chn, book, + page, reg, 1, data[3], crc_chksum); + } + + if (!block->is_ychksum_present || ret >= 0) { + *nr_cmds += 1; + if (len >= 2) + *nr_cmds += ((len - 2) / 4) + 1; + } + +end: + return ret; +} + +static int tasdev_block_chksum(struct tasdevice_priv *tas_priv, + struct tasdev_blk *block, int chn) +{ + unsigned int nr_value; + int ret; + + ret = tasdevice_dev_read(tas_priv, chn, TASDEVICE_I2CChecksum, + &nr_value); + if (ret < 0) { + dev_err(tas_priv->dev, "%s: Chn %d\n", __func__, chn); + set_err_prg_cfg(block->type, &tas_priv->tasdevice[chn]); + goto end; + } + + if ((nr_value & 0xff) != block->pchksum) { + dev_err(tas_priv->dev, "%s: Blk PChkSum Chn %d ", __func__, + chn); + dev_err(tas_priv->dev, "PChkSum = 0x%x, Reg = 0x%x\n", + block->pchksum, (nr_value & 0xff)); + tas_priv->tasdevice[chn].err_code |= ERROR_PRAM_CRCCHK; + ret = -EAGAIN; + block->nr_retry--; + + if (block->nr_retry <= 0) + set_err_prg_cfg(block->type, + &tas_priv->tasdevice[chn]); + } else + tas_priv->tasdevice[chn].err_code &= ~ERROR_PRAM_CRCCHK; + +end: + return ret; +} + +static int tasdev_load_blk(struct tasdevice_priv *tas_priv, + struct tasdev_blk *block, int chn) +{ + unsigned int sleep_time; + unsigned int len; + unsigned int nr_cmds; + unsigned char *data = block->data; + unsigned char crc_chksum = 0; + unsigned char offset; + unsigned char book; + unsigned char page; + unsigned char val; + int ret = 0; + + while (block->nr_retry > 0) { + if (block->is_pchksum_present) { + ret = tasdevice_dev_write(tas_priv, chn, + TASDEVICE_I2CChecksum, 0); + if (ret < 0) + break; + } + + if (block->is_ychksum_present) + crc_chksum = 0; + + nr_cmds = 0; + + while (nr_cmds < block->nr_cmds) { + data = block->data + nr_cmds * 4; + + book = data[0]; + page = data[1]; + offset = data[2]; + val = data[3]; + + nr_cmds++; + /*Single byte write*/ + if (offset <= 0x7F) { + ret = tasdevice_dev_write(tas_priv, chn, + TASDEVICE_REG(book, page, offset), + val); + if (ret < 0) + goto end; + if (block->is_ychksum_present) { + ret = tasdev_bytes_chksum(tas_priv, + block, chn, book, page, offset, + 1, val, &crc_chksum); + if (ret < 0) + break; + } + continue; + } + /*sleep command*/ + if (offset == 0x81) { + /*book -- data[0] page -- data[1]*/ + sleep_time = ((book << 8) + page)*1000; + usleep_range(sleep_time, sleep_time + 50); + continue; + } + /*Multiple bytes write*/ + if (offset == 0x85) { + data += 4; + len = (book << 8) + page; + book = data[0]; + page = data[1]; + offset = data[2]; + ret = tasdev_multibytes_wr(tas_priv, + block, chn, book, page, offset, data, + len, &nr_cmds, &crc_chksum); + if (ret < 0) + break; + } + } + if (ret == -EAGAIN) { + if (block->nr_retry > 0) + continue; + } else if (ret < 0) /*err in current device, skip it*/ + break; + + if (block->is_pchksum_present) { + ret = tasdev_block_chksum(tas_priv, block, chn); + if (ret == -EAGAIN) { + if (block->nr_retry > 0) + continue; + } else if (ret < 0) /*err in current device, skip it*/ + break; + } + + if (block->is_ychksum_present) { + /* TBD, open it when FW ready */ + dev_err(tas_priv->dev, + "Blk YChkSum: FW = 0x%x, YCRC = 0x%x\n", + block->ychksum, crc_chksum); + + tas_priv->tasdevice[chn].err_code &= + ~ERROR_YRAM_CRCCHK; + ret = 0; + } + /*skip current blk*/ + break; + } + +end: + return ret; +} + +static int tasdevice_load_block(struct tasdevice_priv *tas_priv, + struct tasdev_blk *block) +{ + int chnend = 0; + int ret = 0; + int chn = 0; + int rc = 0; + + switch (block->type) { + case MAIN_ALL_DEVICES: + chn = 0; + chnend = tas_priv->ndev; + break; + case MAIN_DEVICE_A: + case COEFF_DEVICE_A: + case PRE_DEVICE_A: + chn = 0; + chnend = 1; + break; + case MAIN_DEVICE_B: + case COEFF_DEVICE_B: + case PRE_DEVICE_B: + chn = 1; + chnend = 2; + break; + case MAIN_DEVICE_C: + case COEFF_DEVICE_C: + case PRE_DEVICE_C: + chn = 2; + chnend = 3; + break; + case MAIN_DEVICE_D: + case COEFF_DEVICE_D: + case PRE_DEVICE_D: + chn = 3; + chnend = 4; + break; + default: + dev_dbg(tas_priv->dev, "load blk: Other Type = 0x%02x\n", + block->type); + break; + } + + for (; chn < chnend; chn++) { + block->nr_retry = 6; + if (tas_priv->tasdevice[chn].is_loading == false) + continue; + ret = tasdev_load_blk(tas_priv, block, chn); + if (ret < 0) + dev_err(tas_priv->dev, "dev %d, Blk (%d) load error\n", + chn, block->type); + rc |= ret; + } + + return rc; +} + +static int dspfw_default_callback(struct tasdevice_priv *tas_priv, + unsigned int drv_ver, unsigned int ppcver) +{ + int rc = 0; + + if (drv_ver == 0x100) { + if (ppcver >= PPC3_VERSION) { + tas_priv->fw_parse_variable_header = + fw_parse_variable_header_kernel; + tas_priv->fw_parse_program_data = + fw_parse_program_data_kernel; + tas_priv->fw_parse_configuration_data = + fw_parse_configuration_data_kernel; + tas_priv->tasdevice_load_block = + tasdevice_load_block_kernel; + } else { + switch (ppcver) { + case 0x00: + tas_priv->fw_parse_variable_header = + fw_parse_variable_header_git; + tas_priv->fw_parse_program_data = + fw_parse_program_data; + tas_priv->fw_parse_configuration_data = + fw_parse_configuration_data; + tas_priv->tasdevice_load_block = + tasdevice_load_block; + break; + default: + dev_err(tas_priv->dev, + "%s: PPCVer must be 0x0 or 0x%02x", + __func__, PPC3_VERSION); + dev_err(tas_priv->dev, " Current:0x%02x\n", + ppcver); + rc = -EINVAL; + break; + } + } + } else { + dev_err(tas_priv->dev, + "DrvVer must be 0x0, 0x230 or above 0x230 "); + dev_err(tas_priv->dev, "current is 0x%02x\n", drv_ver); + rc = -EINVAL; + } + + return rc; +} + +static int load_calib_data(struct tasdevice_priv *tas_priv, + struct tasdevice_data *dev_data) +{ + struct tasdev_blk *block; + unsigned int i; + int ret = 0; + + for (i = 0; i < dev_data->nr_blk; i++) { + block = &(dev_data->dev_blks[i]); + ret = tasdevice_load_block(tas_priv, block); + if (ret < 0) + break; + } + + return ret; +} + +static int fw_parse_header(struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, const struct firmware *fmw, int offset) +{ + struct tasdevice_dspfw_hdr *fw_hdr = &(tas_fmw->fw_hdr); + struct tasdevice_fw_fixed_hdr *fw_fixed_hdr = &(fw_hdr->fixed_hdr); + const unsigned char magic_number[] = { 0x35, 0x35, 0x35, 0x32 }; + const unsigned char *buf = (unsigned char *)fmw->data; + + if (offset + 92 > fmw->size) { + dev_err(tas_priv->dev, "%s: File Size error\n", __func__); + offset = -EINVAL; + goto out; + } + if (memcmp(&buf[offset], magic_number, 4)) { + dev_err(tas_priv->dev, "%s: Magic num NOT match\n", __func__); + offset = -EINVAL; + goto out; + } + offset += 4; + + /* Convert data[offset], data[offset + 1], data[offset + 2] and + * data[offset + 3] into host + */ + fw_fixed_hdr->fwsize = be32_to_cpup((__be32 *)&buf[offset]); + offset += 4; + if (fw_fixed_hdr->fwsize != fmw->size) { + dev_err(tas_priv->dev, "File size not match, %lu %u", + (unsigned long)fmw->size, fw_fixed_hdr->fwsize); + offset = -EINVAL; + goto out; + } + offset += 4; + fw_fixed_hdr->ppcver = be32_to_cpup((__be32 *)&buf[offset]); + offset += 8; + fw_fixed_hdr->drv_ver = be32_to_cpup((__be32 *)&buf[offset]); + offset += 72; + + out: + return offset; +} + +static int fw_parse_variable_hdr_cal(struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, const struct firmware *fmw, int offset) +{ + struct tasdevice_dspfw_hdr *fw_hdr = &(tas_fmw->fw_hdr); + + offset = fw_parse_variable_hdr(tas_priv, fw_hdr, fmw, offset); + if (offset < 0) + goto out; + if (fw_hdr->ndev != 1) { + dev_err(tas_priv->dev, + "%s: calbin must be 1, but currently ndev(%u)\n", + __func__, fw_hdr->ndev); + offset = -EINVAL; + } + +out: + return offset; +} + +/* When calibrated data parsing error occurs, DSP can still work with default + * calibrated data, memory resource related to calibrated data will be + * released in the tasdevice_codec_remove. + */ +static int fw_parse_calibration_data(struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, const struct firmware *fmw, int offset) +{ + struct tasdevice_calibration *calibration; + unsigned char *data = (unsigned char *)fmw->data; + unsigned int i, n; + + if (offset + 2 > fmw->size) { + dev_err(tas_priv->dev, "%s: Calibrations error\n", __func__); + offset = -EINVAL; + goto out; + } + tas_fmw->nr_calibrations = be16_to_cpup((__be16 *)&data[offset]); + offset += 2; + + if (tas_fmw->nr_calibrations != 1) { + dev_err(tas_priv->dev, + "%s: only support one calibraiton(%d)!\n", + __func__, tas_fmw->nr_calibrations); + goto out; + } + + tas_fmw->calibrations = kcalloc(tas_fmw->nr_calibrations, + sizeof(struct tasdevice_calibration), GFP_KERNEL); + if (!tas_fmw->calibrations) { + offset = -ENOMEM; + goto out; + } + for (i = 0; i < tas_fmw->nr_calibrations; i++) { + if (offset + 64 > fmw->size) { + dev_err(tas_priv->dev, "Calibrations error\n"); + offset = -EINVAL; + goto out; + } + calibration = &(tas_fmw->calibrations[i]); + offset += 64; + + n = strlen((char *)&data[offset]); + /* skip '\0' and 2 unused bytes */ + n += 3; + if (offset + n > fmw->size) { + dev_err(tas_priv->dev, "Description err\n"); + offset = -EINVAL; + goto out; + } + offset += n; + + offset = fw_parse_data(tas_fmw, &(calibration->dev_data), fmw, + offset); + if (offset < 0) + goto out; + } + +out: + return offset; +} + +int tas2781_load_calibration(void *context, char *file_name, + enum channel i) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)context; + struct tasdevice *tasdev = &(tas_priv->tasdevice[i]); + const struct firmware *fw_entry; + struct tasdevice_fw *tas_fmw; + struct firmware fmw; + int offset = 0; + int ret; + + ret = request_firmware(&fw_entry, file_name, tas_priv->dev); + if (ret) { + dev_info(tas_priv->dev, "%s: Request firmware %s failed\n", + __func__, file_name); + goto out; + } + + if (!fw_entry->size) { + dev_err(tas_priv->dev, "%s: file read error: size = %lu\n", + __func__, (unsigned long)fw_entry->size); + goto out; + } + fmw.size = fw_entry->size; + fmw.data = fw_entry->data; + + tas_fmw = tasdev->cali_data_fmw = kzalloc(sizeof(struct tasdevice_fw), + GFP_KERNEL); + if (!tasdev->cali_data_fmw) { + ret = -ENOMEM; + goto out; + } + tas_fmw->dev = tas_priv->dev; + offset = fw_parse_header(tas_priv, tas_fmw, &fmw, offset); + if (offset == -EINVAL) { + dev_err(tas_priv->dev, "fw_parse_header EXIT!\n"); + ret = offset; + goto out; + } + offset = fw_parse_variable_hdr_cal(tas_priv, tas_fmw, &fmw, offset); + if (offset == -EINVAL) { + dev_err(tas_priv->dev, + "%s: fw_parse_variable_header_cal EXIT!\n", __func__); + ret = offset; + goto out; + } + offset = fw_parse_program_data(tas_priv, tas_fmw, &fmw, offset); + if (offset < 0) { + dev_err(tas_priv->dev, "fw_parse_program_data EXIT!\n"); + ret = offset; + goto out; + } + offset = fw_parse_configuration_data(tas_priv, tas_fmw, &fmw, offset); + if (offset < 0) { + dev_err(tas_priv->dev, "fw_parse_configuration_data EXIT!\n"); + ret = offset; + goto out; + } + offset = fw_parse_calibration_data(tas_priv, tas_fmw, &fmw, offset); + if (offset < 0) { + dev_err(tas_priv->dev, "fw_parse_calibration_data EXIT!\n"); + ret = offset; + goto out; + } + +out: + if (fw_entry) + release_firmware(fw_entry); + + return ret; +} +EXPORT_SYMBOL_NS_GPL(tas2781_load_calibration, FW_TASDEVICE); + +static int tasdevice_dspfw_ready(const struct firmware *fmw, + void *context) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + struct tasdevice_fw_fixed_hdr *fw_fixed_hdr; + struct tasdevice_fw *tas_fmw; + int offset = 0; + int ret = 0; + + if (!fmw || !fmw->data) { + dev_err(tas_priv->dev, "%s: Failed to read firmware %s\n", + __func__, tas_priv->coef_binaryname); + ret = -EINVAL; + goto out; + } + + tas_priv->fmw = kzalloc(sizeof(struct tasdevice_fw), GFP_KERNEL); + if (!tas_priv->fmw) { + ret = -ENOMEM; + goto out; + } + tas_fmw = tas_priv->fmw; + tas_fmw->dev = tas_priv->dev; + offset = fw_parse_header(tas_priv, tas_fmw, fmw, offset); + + if (offset == -EINVAL) { + ret = -EINVAL; + goto out; + } + fw_fixed_hdr = &(tas_fmw->fw_hdr.fixed_hdr); + /* Support different versions of firmware */ + switch (fw_fixed_hdr->drv_ver) { + case 0x301: + case 0x302: + case 0x502: + tas_priv->fw_parse_variable_header = + fw_parse_variable_header_kernel; + tas_priv->fw_parse_program_data = + fw_parse_program_data_kernel; + tas_priv->fw_parse_configuration_data = + fw_parse_configuration_data_kernel; + tas_priv->tasdevice_load_block = + tasdevice_load_block_kernel; + break; + case 0x202: + case 0x400: + tas_priv->fw_parse_variable_header = + fw_parse_variable_header_git; + tas_priv->fw_parse_program_data = + fw_parse_program_data; + tas_priv->fw_parse_configuration_data = + fw_parse_configuration_data; + tas_priv->tasdevice_load_block = + tasdevice_load_block; + break; + default: + ret = dspfw_default_callback(tas_priv, + fw_fixed_hdr->drv_ver, fw_fixed_hdr->ppcver); + if (ret) + goto out; + break; + } + + offset = tas_priv->fw_parse_variable_header(tas_priv, fmw, offset); + if (offset < 0) { + ret = offset; + goto out; + } + offset = tas_priv->fw_parse_program_data(tas_priv, tas_fmw, fmw, + offset); + if (offset < 0) { + ret = offset; + goto out; + } + offset = tas_priv->fw_parse_configuration_data(tas_priv, + tas_fmw, fmw, offset); + if (offset < 0) + ret = offset; + +out: + return ret; +} + +int tasdevice_dsp_parser(void *context) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)context; + const struct firmware *fw_entry; + int ret; + + ret = request_firmware(&fw_entry, tas_priv->coef_binaryname, + tas_priv->dev); + if (ret) { + dev_err(tas_priv->dev, "%s: load %s error\n", __func__, + tas_priv->coef_binaryname); + goto out; + } + + ret = tasdevice_dspfw_ready(fw_entry, tas_priv); + release_firmware(fw_entry); + fw_entry = NULL; + +out: + return ret; +} +EXPORT_SYMBOL_NS_GPL(tasdevice_dsp_parser, FW_TASDEVICE); + +static void tas2781_clear_calfirmware(struct tasdevice_fw *tas_fmw) +{ + struct tasdevice_calibration *calibration; + struct tasdev_blk *block; + struct tasdevice_data *im; + unsigned int blks; + int i; + + if (!tas_fmw->calibrations) + goto out; + + for (i = 0; i < tas_fmw->nr_calibrations; i++) { + calibration = &(tas_fmw->calibrations[i]); + if (!calibration) + continue; + + im = &(calibration->dev_data); + + if (!im->dev_blks) + continue; + + for (blks = 0; blks < im->nr_blk; blks++) { + block = &(im->dev_blks[blks]); + if (!block) + continue; + kfree(block->data); + } + kfree(im->dev_blks); + } + kfree(tas_fmw->calibrations); +out: + kfree(tas_fmw); +} + +void tasdevice_calbin_remove(void *context) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + struct tasdevice *tasdev; + int i; + + if (!tas_priv) + return; + + for (i = 0; i < tas_priv->ndev; i++) { + tasdev = &(tas_priv->tasdevice[i]); + if (!tasdev->cali_data_fmw) + continue; + tas2781_clear_calfirmware(tasdev->cali_data_fmw); + tasdev->cali_data_fmw = NULL; + } +} +EXPORT_SYMBOL_NS_GPL(tasdevice_calbin_remove, FW_TASDEVICE); + +void tasdevice_config_info_remove(void *context) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + struct tasdevice_rca *rca = &(tas_priv->rcabin); + struct tasdevice_config_info **ci = rca->cfg_info; + int i, j; + + if (!ci) + return; + for (i = 0; i < rca->ncfgs; i++) { + if (!ci[i]) + continue; + if (ci[i]->blk_data) { + for (j = 0; j < (int)ci[i]->real_nblocks; j++) { + if (!ci[i]->blk_data[j]) + continue; + kfree(ci[i]->blk_data[j]->regdata); + kfree(ci[i]->blk_data[j]); + } + kfree(ci[i]->blk_data); + } + kfree(ci[i]); + } + kfree(ci); +} +EXPORT_SYMBOL_NS_GPL(tasdevice_config_info_remove, FW_TASDEVICE); + +static int tasdevice_load_data(struct tasdevice_priv *tas_priv, + struct tasdevice_data *dev_data) +{ + struct tasdev_blk *block; + unsigned int i; + int ret = 0; + + for (i = 0; i < dev_data->nr_blk; i++) { + block = &(dev_data->dev_blks[i]); + ret = tas_priv->tasdevice_load_block(tas_priv, block); + if (ret < 0) + break; + } + + return ret; +} + +int tasdevice_select_tuningprm_cfg(void *context, int prm_no, + int cfg_no, int rca_conf_no) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + struct tasdevice_rca *rca = &(tas_priv->rcabin); + struct tasdevice_config_info **cfg_info = rca->cfg_info; + struct tasdevice_fw *tas_fmw = tas_priv->fmw; + struct tasdevice_prog *program; + struct tasdevice_config *conf; + int prog_status = 0; + int status, i; + + if (!tas_fmw) { + dev_err(tas_priv->dev, "%s: Firmware is NULL\n", __func__); + goto out; + } + + if (cfg_no >= tas_fmw->nr_configurations) { + dev_err(tas_priv->dev, + "%s: cfg(%d) is not in range of conf %u\n", + __func__, cfg_no, tas_fmw->nr_configurations); + goto out; + } + + if (prm_no >= tas_fmw->nr_programs) { + dev_err(tas_priv->dev, + "%s: prm(%d) is not in range of Programs %u\n", + __func__, prm_no, tas_fmw->nr_programs); + goto out; + } + + if (rca_conf_no > rca->ncfgs || rca_conf_no <= 0 || + !cfg_info) { + dev_err(tas_priv->dev, + "conf_no:%d should be in range from 0 to %u\n", + rca_conf_no, rca->ncfgs-1); + goto out; + } + + conf = &(tas_fmw->configs[cfg_no]); + for (i = 0, prog_status = 0; i < tas_priv->ndev; i++) { + if (cfg_info[rca_conf_no]->active_dev & (1 << i)) { + if (tas_priv->tasdevice[i].cur_prog != prm_no) { + tas_priv->tasdevice[i].cur_conf = -1; + tas_priv->tasdevice[i].is_loading = true; + prog_status++; + } + } else + tas_priv->tasdevice[i].is_loading = false; + tas_priv->tasdevice[i].is_loaderr = false; + } + + if (prog_status) { + program = &(tas_fmw->programs[prm_no]); + tasdevice_load_data(tas_priv, &(program->dev_data)); + for (i = 0; i < tas_priv->ndev; i++) { + if (tas_priv->tasdevice[i].is_loaderr == true) + continue; + else if (tas_priv->tasdevice[i].is_loaderr == false + && tas_priv->tasdevice[i].is_loading == true) { + struct tasdevice_fw *cal_fmw = + tas_priv->tasdevice[i].cali_data_fmw; + + if (cal_fmw) { + struct tasdevice_calibration + *cal = cal_fmw->calibrations; + + if (cal) + load_calib_data(tas_priv, + &(cal->dev_data)); + } + tas_priv->tasdevice[i].cur_prog = prm_no; + } + } + } + + for (i = 0, status = 0; i < tas_priv->ndev; i++) { + if (tas_priv->tasdevice[i].cur_conf != cfg_no + && (cfg_info[rca_conf_no]->active_dev & (1 << i)) + && (tas_priv->tasdevice[i].is_loaderr == false)) { + status++; + tas_priv->tasdevice[i].is_loading = true; + } else + tas_priv->tasdevice[i].is_loading = false; + } + + if (status) { + status = 0; + tasdevice_load_data(tas_priv, &(conf->dev_data)); + for (i = 0; i < tas_priv->ndev; i++) { + if (tas_priv->tasdevice[i].is_loaderr == true) { + status |= 1 << (i + 4); + continue; + } else if (tas_priv->tasdevice[i].is_loaderr == false + && tas_priv->tasdevice[i].is_loading == true) + tas_priv->tasdevice[i].cur_conf = cfg_no; + } + } else + dev_err(tas_priv->dev, + "%s: No device is in active in conf %d\n", + __func__, rca_conf_no); + + status |= cfg_info[rca_conf_no]->active_dev; + +out: + return prog_status; +} +EXPORT_SYMBOL_NS_GPL(tasdevice_select_tuningprm_cfg, FW_TASDEVICE); + +int tasdevice_prmg_load(void *context, int prm_no) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + struct tasdevice_fw *tas_fmw = tas_priv->fmw; + struct tasdevice_prog *program; + int prog_status = 0; + int i; + + if (!tas_fmw) { + dev_err(tas_priv->dev, "%s: Firmware is NULL\n", __func__); + goto out; + } + + if (prm_no >= tas_fmw->nr_programs) { + dev_err(tas_priv->dev, + "%s: prm(%d) is not in range of Programs %u\n", + __func__, prm_no, tas_fmw->nr_programs); + goto out; + } + + for (i = 0, prog_status = 0; i < tas_priv->ndev; i++) { + if (tas_priv->tasdevice[i].cur_prog != prm_no) { + tas_priv->tasdevice[i].cur_conf = -1; + tas_priv->tasdevice[i].is_loading = true; + prog_status++; + } + } + + if (prog_status) { + program = &(tas_fmw->programs[prm_no]); + tasdevice_load_data(tas_priv, &(program->dev_data)); + for (i = 0; i < tas_priv->ndev; i++) { + if (tas_priv->tasdevice[i].is_loaderr == true) + continue; + else if (tas_priv->tasdevice[i].is_loaderr == false + && tas_priv->tasdevice[i].is_loading == true) + tas_priv->tasdevice[i].cur_prog = prm_no; + } + } + if (tas_priv->set_global_mode) + tas_priv->set_global_mode(tas_priv); +out: + return prog_status; +} +EXPORT_SYMBOL_NS_GPL(tasdevice_prmg_load, FW_TASDEVICE); + +int tasdevice_prmg_calibdata_load(void *context, int prm_no) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + struct tasdevice_fw *tas_fmw = tas_priv->fmw; + struct tasdevice_prog *program; + int prog_status = 0; + int i; + + if (!tas_fmw) { + dev_err(tas_priv->dev, "%s: Firmware is NULL\n", __func__); + goto out; + } + + if (prm_no >= tas_fmw->nr_programs) { + dev_err(tas_priv->dev, + "%s: prm(%d) is not in range of Programs %u\n", + __func__, prm_no, tas_fmw->nr_programs); + goto out; + } + + for (i = 0, prog_status = 0; i < tas_priv->ndev; i++) { + if (tas_priv->tasdevice[i].cur_prog != prm_no) { + tas_priv->tasdevice[i].cur_conf = -1; + tas_priv->tasdevice[i].is_loading = true; + prog_status++; + } + tas_priv->tasdevice[i].is_loaderr = false; + } + + if (prog_status) { + program = &(tas_fmw->programs[prm_no]); + tasdevice_load_data(tas_priv, &(program->dev_data)); + for (i = 0; i < tas_priv->ndev; i++) { + if (tas_priv->tasdevice[i].is_loaderr == true) + continue; + else if (tas_priv->tasdevice[i].is_loaderr == false + && tas_priv->tasdevice[i].is_loading == true) { + struct tasdevice_fw *cal_fmw = + tas_priv->tasdevice[i].cali_data_fmw; + + if (cal_fmw) { + struct tasdevice_calibration *cal = + cal_fmw->calibrations; + + if (cal) + load_calib_data(tas_priv, + &(cal->dev_data)); + } + tas_priv->tasdevice[i].cur_prog = prm_no; + } + } + } + +out: + return prog_status; +} +EXPORT_SYMBOL_NS_GPL(tasdevice_prmg_calibdata_load, FW_TASDEVICE); + +void tasdevice_tuning_switch(void *context, int state) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + struct tasdevice_fw *tas_fmw = tas_priv->fmw; + int profile_cfg_id = 0; + + if (tas_priv->fw_state == TASDEVICE_DSP_FW_FAIL) { + dev_err(tas_priv->dev, "DSP bin file not loaded\n"); + return; + } + + if (state == 0) { + if (tas_priv->cur_prog >= tas_fmw->nr_programs) + /*bypass all in rca is profile id 0*/ + profile_cfg_id = RCA_CONFIGID_BYPASS_ALL; + else { + /*dsp mode or tuning mode*/ + profile_cfg_id = tas_priv->rcabin.profile_cfg_id; + tasdevice_select_tuningprm_cfg(tas_priv, + tas_priv->cur_prog, tas_priv->cur_conf, + profile_cfg_id); + if (tas_priv->set_global_mode) + tas_priv->set_global_mode(tas_priv); + } + + tasdevice_select_cfg_blk(tas_priv, profile_cfg_id, + TASDEVICE_BIN_BLK_PRE_POWER_UP); + } else + tasdevice_select_cfg_blk(tas_priv, + tas_priv->rcabin.profile_cfg_id, + TASDEVICE_BIN_BLK_PRE_SHUTDOWN); +} +EXPORT_SYMBOL_NS_GPL(tasdevice_tuning_switch, FW_TASDEVICE); + +MODULE_DESCRIPTION("Texas Firmware Support"); +MODULE_AUTHOR("Shenghao Ding, TI, <shenghao-ding(a)ti.com>"); +MODULE_LICENSE("GPL"); -- 2.34.1

3 3

[PATCH] ALSA: pcm: fix snd_pcm_playback_silence() with free-running mode
by Oswald Buddenhagen 04 May '23

04 May '23

Turns out that we cannot rely on the application pointer being updated in top-up mode, as its primary purpose is to remain operational in free-running mode as used by dmix. So we logically revert some bits from commit 9f656705c5faa ("ALSA: pcm: rewrite snd_pcm_playback_silence()"), but we retain the bug fixes and try to make the code paths congruent. Reported-by: Jeff Chua <jeff.chua.linux(a)gmail.com> Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- sound/core/pcm_lib.c | 82 +++++++++++++++++++++++++++-------------- sound/core/pcm_local.h | 3 +- sound/core/pcm_native.c | 6 +-- 3 files changed, 60 insertions(+), 31 deletions(-) diff --git a/sound/core/pcm_lib.c b/sound/core/pcm_lib.c index d21c73944efd..cd5f2ef14ab4 100644 --- a/sound/core/pcm_lib.c +++ b/sound/core/pcm_lib.c @@ -42,41 +42,69 @@ static int fill_silence_frames(struct snd_pcm_substream *substream, * * when runtime->silence_size >= runtime->boundary - fill processed area with silence immediately */ -void snd_pcm_playback_silence(struct snd_pcm_substream *substream) +void snd_pcm_playback_silence(struct snd_pcm_substream *substream, snd_pcm_uframes_t new_hw_ptr) { struct snd_pcm_runtime *runtime = substream->runtime; - snd_pcm_uframes_t appl_ptr = READ_ONCE(runtime->control->appl_ptr); - snd_pcm_sframes_t added, hw_avail, frames; + snd_pcm_sframes_t hw_avail, frames; snd_pcm_uframes_t noise_dist, ofs, transfer; int err; - added = appl_ptr - runtime->silence_start; - if (added) { - if (added < 0) - added += runtime->boundary; - if (added < runtime->silence_filled) - runtime->silence_filled -= added; - else - runtime->silence_filled = 0; - runtime->silence_start = appl_ptr; - } - - // This will "legitimately" turn negative on underrun, and will be mangled - // into a huge number by the boundary crossing handling. The initial state - // might also be not quite sane. The code below MUST account for these cases. - hw_avail = appl_ptr - runtime->status->hw_ptr; - if (hw_avail < 0) - hw_avail += runtime->boundary; - - noise_dist = hw_avail + runtime->silence_filled; if (runtime->silence_size < runtime->boundary) { + snd_pcm_uframes_t appl_ptr = READ_ONCE(runtime->control->appl_ptr); + snd_pcm_sframes_t added = appl_ptr - runtime->silence_start; + if (added) { + if (added < 0) + added += runtime->boundary; + if (added < runtime->silence_filled) + runtime->silence_filled -= added; + else + runtime->silence_filled = 0; + runtime->silence_start = appl_ptr; + } + + if (new_hw_ptr == ULONG_MAX) // initialization + new_hw_ptr = runtime->status->hw_ptr; + // This will "legitimately" turn negative on underrun, and will be mangled + // into a huge number by the boundary crossing handling. The initial state + // might also be not quite sane. The code below MUST account for these cases. + hw_avail = appl_ptr - new_hw_ptr; + if (hw_avail < 0) + hw_avail += runtime->boundary; + + noise_dist = hw_avail + runtime->silence_filled; frames = runtime->silence_threshold - noise_dist; if (frames <= 0) return; if (frames > runtime->silence_size) frames = runtime->silence_size; } else { - frames = runtime->buffer_size - noise_dist; + // This filling mode aims at free-running mode (used for example by dmix), + // which doesn't update the application pointer. + snd_pcm_uframes_t hw_ptr = runtime->status->hw_ptr; + if (new_hw_ptr == ULONG_MAX) { // initialization + // Usually, this is entered while stopped, before data is queued, + // so both pointers are expected to be zero. + hw_avail = runtime->control->appl_ptr - hw_ptr; + if (hw_avail < 0) + hw_avail += runtime->boundary; + // In free-running mode, appl_ptr will be zero even while running, + // so we end up with a huge number. There is no useful way to + // handle this, so we just clear the whole buffer. + runtime->silence_filled = hw_avail > runtime->buffer_size ? 0 : hw_avail; + runtime->silence_start = hw_ptr; + } else { + snd_pcm_sframes_t played = new_hw_ptr - hw_ptr; + if (played) { + if (played < 0) + played += runtime->boundary; + if (played < runtime->silence_filled) + runtime->silence_filled -= played; + else // This may happen due to a reset. + runtime->silence_filled = 0; + runtime->silence_start = new_hw_ptr; + } + } + frames = runtime->buffer_size - runtime->silence_filled; if (frames <= 0) return; } @@ -425,6 +453,10 @@ static int snd_pcm_update_hw_ptr0(struct snd_pcm_substream *substream, return 0; } + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && + runtime->silence_size > 0) + snd_pcm_playback_silence(substream, new_hw_ptr); + if (in_interrupt) { delta = new_hw_ptr - runtime->hw_ptr_interrupt; if (delta < 0) @@ -442,10 +474,6 @@ static int snd_pcm_update_hw_ptr0(struct snd_pcm_substream *substream, runtime->hw_ptr_wrap += runtime->boundary; } - if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && - runtime->silence_size > 0) - snd_pcm_playback_silence(substream); - update_audio_tstamp(substream, &curr_tstamp, &audio_tstamp); return snd_pcm_update_state(substream, runtime); diff --git a/sound/core/pcm_local.h b/sound/core/pcm_local.h index 42fe3a4e9154..ecb21697ae3a 100644 --- a/sound/core/pcm_local.h +++ b/sound/core/pcm_local.h @@ -29,7 +29,8 @@ int snd_pcm_update_state(struct snd_pcm_substream *substream, struct snd_pcm_runtime *runtime); int snd_pcm_update_hw_ptr(struct snd_pcm_substream *substream); -void snd_pcm_playback_silence(struct snd_pcm_substream *substream); +void snd_pcm_playback_silence(struct snd_pcm_substream *substream, + snd_pcm_uframes_t new_hw_ptr); static inline snd_pcm_uframes_t snd_pcm_avail(struct snd_pcm_substream *substream) diff --git a/sound/core/pcm_native.c b/sound/core/pcm_native.c index 3d0c4a5b701b..94185267a7b9 100644 --- a/sound/core/pcm_native.c +++ b/sound/core/pcm_native.c @@ -958,7 +958,7 @@ static int snd_pcm_sw_params(struct snd_pcm_substream *substream, if (snd_pcm_running(substream)) { if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && runtime->silence_size > 0) - snd_pcm_playback_silence(substream); + snd_pcm_playback_silence(substream, ULONG_MAX); err = snd_pcm_update_state(substream, runtime); } snd_pcm_stream_unlock_irq(substream); @@ -1455,7 +1455,7 @@ static void snd_pcm_post_start(struct snd_pcm_substream *substream, __snd_pcm_set_state(runtime, state); if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && runtime->silence_size > 0) - snd_pcm_playback_silence(substream); + snd_pcm_playback_silence(substream, ULONG_MAX); snd_pcm_timer_notify(substream, SNDRV_TIMER_EVENT_MSTART); } @@ -1916,7 +1916,7 @@ static void snd_pcm_post_reset(struct snd_pcm_substream *substream, runtime->control->appl_ptr = runtime->status->hw_ptr; if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && runtime->silence_size > 0) - snd_pcm_playback_silence(substream); + snd_pcm_playback_silence(substream, ULONG_MAX); snd_pcm_stream_unlock_irq(substream); } -- 2.40.0.152.g15d061e6df

4 14

How to mix multiple pcm capture stream into one and save to wav file as if it's from one single multi channel alsa card device
by semiydsemiyd＠163.com 04 May '23

04 May '23

Hi I have 8 alsa capture devices for one card. Each capture device support 1 channel only: root@light-a-val:~# arecord -l **** List of CAPTURE Hardware Devices **** card 0: LightSoundCard [Light-Sound-Card], device 0: light-tdm-dai-slot1-ES7210 ADC 0 es7210.5-0042-1 [light-tdm-dai-slot1-ES7210 ADC 0 es7210.5-0042-1] Subdevices: 1/8 Subdevice #0: subdevice #0 card 0: LightSoundCard [Light-Sound-Card], device 1: light-tdm-dai-slot2-ES7210 ADC 0 es7210.5-0042-1 [light-tdm-dai-slot1-ES7210 ADC 0 es7210.5-0042-1] Subdevices: 2/8 Subdevice #1: subdevice #1 ... card 0: LightSoundCard [Light-Sound-Card], device 7: light-tdm-dai-slot8-ES7210 ADC 1 es7210.5-0042-1 [light-tdm-dai-slot1-ES7210 ADC 0 es7210.5-0042-1] Subdevices: 8/8 Subdevice #7: subdevice #7 the signal comes in TDM format from external codec ES7210 to my soc's TDM controller. each capture device has 1 channel that correspond to one of the slot in TDM. i have 8 TDM slots in configuration. so i have 8 devices in total. the reason that i have so many capture devices with 1 channel each is that, our tdm IC design decides that each tdm slot data_register would be assigned a dedicated dma channel. this is quite uncommon. thus i have 8 dma channels for 8 tdm slots. since i can only register one rx dma channel and one tx using devm_snd_dmaengine_pcm_register(). like: struct dmaengine_pcm { struct dma_chan *chan[SNDRV_PCM_STREAM_LAST + 1]; // there can be only one tx + one rx dma for struct dmaengine_pcm ... }; i have to register like 8 times to create 8 devices. the dts for the cpu dai driver for tdm slot1 would look like: tdm: audio_tdm@0xffcb000000 { #sound-dai-cells = <0>; ... dmas = <&dmac2 31>; dma-names = "rx"; ... }; now...i want to open all the devices at the same time. and have them save to one single wav file. As if i'm opening one single alsa capture device with 8 channels. the saved wav file should look something like this (take this 8 channel wav file for example) First Multichannel Sample -------------------------- {BB FF FF} 3 bytes slot1 {A1 FF FF} 3 bytes slot2 {00 00 00} 3 bytes slot3 {00 00 00} 3 bytes slot4 {00 00 00} 3 bytes slot5 {00 00 00} 3 bytes slot6 {00 00 00} 3 bytes slot7 {00 00 00} 3 bytes slot8 Second Multichannel Sample -------------------------- {E6 FF FF} 3 bytes slot1 .,.. etc .... Is this possible and if yes how can i do that? thank you guys semiyd

3 3

[PATCH] ALSA: usb-audio: Add quirk for Pioneer DDJ-800
by Geraldo Nascimento 04 May '23

04 May '23

One more Pioneer quirk, this time for DDJ-800, which is quite similar like other DJ DDJ models but with slightly different EPs or channels. Signed-off-by: Geraldo Nascimento <geraldogabriel(a)gmail.com> Tested-by: Grégory Desor <gregory.desor(a)free.fr> --- Hi Takashi, this one cropped up in the Mixxx forums as a request and it works. Grégory says Master and Headphones work OK with this patch, MIC inputs are untested. Thanks! --- sound/usb/quirks-table.h 2023-05-03 17:55:23.133827915 -0300 +++ sound/usb/quirks-table.h 2023-05-03 17:56:29.054827946 -0300 @@ -3884,6 +3884,64 @@ YAMAHA_DEVICE(0x7010, "UB99"), } }, +{ + /* + * PIONEER DJ DDJ-800 + * PCM is 6 channels out, 6 channels in @ 44.1 fixed + * The Feedback for the output is the input + */ + USB_DEVICE_VENDOR_SPEC(0x2b73, 0x0029), + .driver_info = (unsigned long) &(const struct snd_usb_audio_quirk) { + .ifnum = QUIRK_ANY_INTERFACE, + .type = QUIRK_COMPOSITE, + .data = (const struct snd_usb_audio_quirk[]) { + { + .ifnum = 0, + .type = QUIRK_AUDIO_FIXED_ENDPOINT, + .data = &(const struct audioformat) { + .formats = SNDRV_PCM_FMTBIT_S24_3LE, + .channels = 6, + .iface = 0, + .altsetting = 1, + .altset_idx = 1, + .endpoint = 0x01, + .ep_attr = USB_ENDPOINT_XFER_ISOC| + USB_ENDPOINT_SYNC_ASYNC, + .rates = SNDRV_PCM_RATE_44100, + .rate_min = 44100, + .rate_max = 44100, + .nr_rates = 1, + .rate_table = (unsigned int[]) { 44100 } + } + }, + { + .ifnum = 0, + .type = QUIRK_AUDIO_FIXED_ENDPOINT, + .data = &(const struct audioformat) { + .formats = SNDRV_PCM_FMTBIT_S24_3LE, + .channels = 6, + .iface = 0, + .altsetting = 1, + .altset_idx = 1, + .endpoint = 0x82, + .ep_idx = 1, + .ep_attr = USB_ENDPOINT_XFER_ISOC| + USB_ENDPOINT_SYNC_ASYNC| + USB_ENDPOINT_USAGE_IMPLICIT_FB, + .rates = SNDRV_PCM_RATE_44100, + .rate_min = 44100, + .rate_max = 44100, + .nr_rates = 1, + .rate_table = (unsigned int[]) { 44100 } + } + }, + { + .ifnum = -1 + } + } + } +}, + /* * MacroSilicon MS2100/MS2106 based AV capture cards *

2 2

[PATCH] sound: caiaq: input: Add error handling for unsupported input methods in `snd_usb_caiaq_input_init`
by Ruliang Lin 04 May '23

04 May '23

Smatch complains that: snd_usb_caiaq_input_init() warn: missing error code 'ret' This patch adds a new case to handle the situation where the device does not support any input methods in the `snd_usb_caiaq_input_init` function. It returns an `-EINVAL` error code to indicate that no input methods are supported on the device. Fixes: 523f1dce3743 ("[ALSA] Add Native Instrument usb audio device support") Signed-off-by: Ruliang Lin <u202112092(a)hust.edu.cn> Reviewed-by: Dongliang Mu <dzm91(a)hust.edu.cn> --- The issue is found by static analyzer. The patched code has passed Smatch checker, but remains untested on real device. --- sound/usb/caiaq/input.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/usb/caiaq/input.c b/sound/usb/caiaq/input.c index 1e2cf2f08eec..84f26dce7f5d 100644 --- a/sound/usb/caiaq/input.c +++ b/sound/usb/caiaq/input.c @@ -804,6 +804,7 @@ int snd_usb_caiaq_input_init(struct snd_usb_caiaqdev *cdev) default: /* no input methods supported on this device */ + ret = -EINVAL; goto exit_free_idev; } -- 2.25.1

3 2

[PATCH] alsa: support HP Pavilion Aero 13-be0xxx Mute LED
by Caleb Harper 04 May '23

04 May '23

This patch adds support for the mute LED on the HP Pavilion Aero Laptop 13-be0xxx. The current behavior is that the LED does not turn on at any time and does not indicate to the user whether the sound is muted. The solution is to add a PCI quirk to properly recognize and support the LED on this device. This change has been tested on the device in question using modified versions of kernels 6.0.7-6.2.12 on Arch Linux. Signed-off-by: Caleb Harper <calebharp2005(a)gmail.com> --- sound/pci/hda/patch_realtek.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index f70d6a33421d..aeffe6bd8b98 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -9428,6 +9428,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x103c, 0x8898, "HP EliteBook 845 G8 Notebook PC", ALC285_FIXUP_HP_LIMIT_INT_MIC_BOOST), SND_PCI_QUIRK(0x103c, 0x88d0, "HP Pavilion 15-eh1xxx (mainboard 88D0)", ALC287_FIXUP_HP_GPIO_LED), SND_PCI_QUIRK(0x103c, 0x8902, "HP OMEN 16", ALC285_FIXUP_HP_MUTE_LED), + SND_PCI_QUIRK(0x103c, 0x8919, "HP Pavilion Aero Laptop 13-be0xxx", ALC287_FIXUP_HP_GPIO_LED), SND_PCI_QUIRK(0x103c, 0x896d, "HP ZBook Firefly 16 G9", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED), SND_PCI_QUIRK(0x103c, 0x896e, "HP EliteBook x360 830 G9", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED), SND_PCI_QUIRK(0x103c, 0x8971, "HP EliteBook 830 G9", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED), -- 2.40.1

2 1

alsalib assertion using plug+dmix
by GitHub issues - opened 04 May '23

04 May '23

alsa-project/alsa-lib issue #314 was opened from npitre: The espeak program is crashing randomly here. I've been able to isolate the issue in a small test program demonstrating the crash 100% of the time, ending in: ``` alsa_quickcrash: pcm.c:3236: snd_pcm_area_copy: Assertion `src < dst || src >= dst + bytes' failed. Aborted (core dumped) ``` Here's the test code: ``` /* to compile: gcc -O2 -Wall -o alsa_quickcrash alsa_quickcrash.c -lasound */ #include <alsa/asoundlib.h> #include <stdio.h> #include <string.h> #define DEVICE "test_dummy" #define RATE 22050 #define CHANNELS 1 #define FORMAT SND_PCM_FORMAT_S16_LE #define BUF_MS 60 #define DO(x) if (x < 0) { fprintf(stderr, "%s failed\n", #x); exit(1); } int main() { unsigned int rate = RATE; snd_pcm_uframes_t frames = RATE * BUF_MS / 1000; snd_pcm_t *handle; snd_pcm_hw_params_t *params; DO(snd_pcm_hw_params_malloc(&params)); DO(snd_pcm_open(&handle, DEVICE, SND_PCM_STREAM_PLAYBACK, 0)); DO(snd_pcm_hw_params_any(handle, params)); DO(snd_pcm_hw_params_set_access(handle, params, SND_PCM_ACCESS_RW_INTERLEAVED)); DO(snd_pcm_hw_params_set_format(handle, params, FORMAT)); DO(snd_pcm_hw_params_set_rate_near(handle, params, &rate, 0)); DO(snd_pcm_hw_params_set_channels(handle, params, CHANNELS)); DO(snd_pcm_hw_params_set_buffer_size_near(handle, params, &frames)); DO(snd_pcm_hw_params(handle, params)); DO(snd_pcm_prepare(handle)); printf("PCM config dump:\n"); snd_output_t *output = NULL; DO(snd_output_stdio_attach(&output, stdout, 0)); DO(snd_pcm_dump(handle, output)); printf("\n"); printf("frames = %ld\n", (long)frames); short data[frames * CHANNELS]; memset(data, 0, sizeof(data)); printf("writing whole buffer\n"); DO(snd_pcm_writei(handle, data, frames)); printf("writing whole buffer\n"); DO(snd_pcm_writei(handle, data, frames)); printf("writing whole buffer minus 1 frame\n"); DO(snd_pcm_writei(handle, data, frames - 1)); printf("draining audio\n"); DO(snd_pcm_drain(handle)); printf("done\n"); DO(snd_pcm_close(handle)); return 0; } ``` Here's the corresponding .asoundrc content: ``` pcm.test_dummy { type plug slave.pcm "mix_dummy" } pcm.mix_dummy { type dmix ipc_key 1024 ipc_key_add_uid false ipc_perm 0666 slave { pcm "hw:0" period_size 1024 buffer_size 4096 format "S16_LE" rate 48000 } } ``` And here's the complete test output: ``` PCM config dump: Plug PCM: Rate conversion PCM (48000, sformat=S16_LE) Converter: linear-interpolation Protocol version: 10003 Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 22050 exact rate : 22050 (22050/1) msbits : 16 buffer_size : 1411 period_size : 470 period_time : 21333 tstamp_mode : NONE tstamp_type : MONOTONIC period_step : 1 avail_min : 470 period_event : 0 start_threshold : 1 stop_threshold : 1411 silence_threshold: 0 silence_size : 0 boundary : 3177289537109884928 Slave: Route conversion PCM (sformat=S16_LE) Transformation table: 0 <- 0 1 <- 0 Its setup is: stream : PLAYBACK access : MMAP_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 48000 exact rate : 48000 (48000/1) msbits : 16 buffer_size : 3072 period_size : 1024 period_time : 21333 tstamp_mode : NONE tstamp_type : MONOTONIC period_step : 1 avail_min : 1024 period_event : 0 start_threshold : 2 stop_threshold : 3072 silence_threshold: 0 silence_size : 0 boundary : 6917529027641081856 Slave: Direct Stream Mixing PCM Its setup is: stream : PLAYBACK access : MMAP_INTERLEAVED format : S16_LE subformat : STD channels : 2 rate : 48000 exact rate : 48000 (48000/1) msbits : 16 buffer_size : 3072 period_size : 1024 period_time : 21333 tstamp_mode : NONE tstamp_type : MONOTONIC period_step : 1 avail_min : 1024 period_event : 0 start_threshold : 2 stop_threshold : 3072 silence_threshold: 0 silence_size : 0 boundary : 6917529027641081856 Hardware PCM card 1 'HDA Intel PCH' device 0 subdevice 0 Its setup is: stream : PLAYBACK access : MMAP_INTERLEAVED format : S16_LE subformat : STD channels : 2 rate : 48000 exact rate : 48000 (48000/1) msbits : 16 buffer_size : 4096 period_size : 1024 period_time : 21333 tstamp_mode : ENABLE tstamp_type : MONOTONIC period_step : 1 avail_min : 1024 period_event : 0 start_threshold : 1 stop_threshold : 0 silence_threshold: 0 silence_size : 0 boundary : 4611686018427387904 appl_ptr : 0 hw_ptr : 2734916609 frames = 1411 writing whole buffer writing whole buffer writing whole buffer minus 1 frame draining audio alsa_quickcrash: pcm.c:3236: snd_pcm_area_copy: Assertion `src < dst || src >= dst + bytes' failed. Aborted (core dumped) ``` Issue URL : https://github.com/alsa-project/alsa-lib/issues/314 Repository URL: https://github.com/alsa-project/alsa-lib

1 0

alsalib assertion using plug+dmix
by GitHub issues - edited 04 May '23

04 May '23

alsa-project/alsa-lib issue #314 was edited from npitre: The espeak program is crashing randomly here. I've been able to isolate the issue in a small test program demonstrating the crash 100% of the time, ending in: ``` alsa_quickcrash: pcm.c:3236: snd_pcm_area_copy: Assertion `src < dst || src >= dst + bytes' failed. Aborted (core dumped) ``` Here's the test code: ``` /* to compile: gcc -O2 -Wall -o alsa_quickcrash alsa_quickcrash.c -lasound */ #include <alsa/asoundlib.h> #include <stdio.h> #include <string.h> #define DEVICE "test_dummy" #define RATE 22050 #define CHANNELS 1 #define FORMAT SND_PCM_FORMAT_S16_LE #define BUF_MS 60 #define DO(x) if (x < 0) { fprintf(stderr, "%s failed\n", #x); exit(1); } int main() { unsigned int rate = RATE; snd_pcm_uframes_t frames = RATE * BUF_MS / 1000; snd_pcm_t *handle; snd_pcm_hw_params_t *params; DO(snd_pcm_hw_params_malloc(&params)); DO(snd_pcm_open(&handle, DEVICE, SND_PCM_STREAM_PLAYBACK, 0)); DO(snd_pcm_hw_params_any(handle, params)); DO(snd_pcm_hw_params_set_access(handle, params, SND_PCM_ACCESS_RW_INTERLEAVED)); DO(snd_pcm_hw_params_set_format(handle, params, FORMAT)); DO(snd_pcm_hw_params_set_rate_near(handle, params, &rate, 0)); DO(snd_pcm_hw_params_set_channels(handle, params, CHANNELS)); DO(snd_pcm_hw_params_set_buffer_size_near(handle, params, &frames)); DO(snd_pcm_hw_params(handle, params)); DO(snd_pcm_prepare(handle)); printf("PCM config dump:\n"); snd_output_t *output = NULL; DO(snd_output_stdio_attach(&output, stdout, 0)); DO(snd_pcm_dump(handle, output)); printf("\n"); printf("frames = %ld\n", (long)frames); short data[frames * CHANNELS]; memset(data, 0, sizeof(data)); printf("writing whole buffer\n"); DO(snd_pcm_writei(handle, data, frames)); printf("writing whole buffer\n"); DO(snd_pcm_writei(handle, data, frames)); printf("writing whole buffer minus 1 frame\n"); DO(snd_pcm_writei(handle, data, frames - 1)); printf("draining audio\n"); DO(snd_pcm_drain(handle)); printf("done\n"); DO(snd_pcm_close(handle)); return 0; } ``` Here's the corresponding .asoundrc content: ``` pcm.test_dummy { type plug slave.pcm "mix_dummy" } pcm.mix_dummy { type dmix ipc_key 1024 ipc_key_add_uid false ipc_perm 0666 slave { pcm "hw:0" period_size 1024 buffer_size 4096 format "S16_LE" rate 48000 } } ``` And here's the complete test output: ``` PCM config dump: Plug PCM: Rate conversion PCM (48000, sformat=S16_LE) Converter: linear-interpolation Protocol version: 10003 Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 22050 exact rate : 22050 (22050/1) msbits : 16 buffer_size : 1411 period_size : 470 period_time : 21333 tstamp_mode : NONE tstamp_type : MONOTONIC period_step : 1 avail_min : 470 period_event : 0 start_threshold : 1 stop_threshold : 1411 silence_threshold: 0 silence_size : 0 boundary : 3177289537109884928 Slave: Route conversion PCM (sformat=S16_LE) Transformation table: 0 <- 0 1 <- 0 Its setup is: stream : PLAYBACK access : MMAP_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 48000 exact rate : 48000 (48000/1) msbits : 16 buffer_size : 3072 period_size : 1024 period_time : 21333 tstamp_mode : NONE tstamp_type : MONOTONIC period_step : 1 avail_min : 1024 period_event : 0 start_threshold : 2 stop_threshold : 3072 silence_threshold: 0 silence_size : 0 boundary : 6917529027641081856 Slave: Direct Stream Mixing PCM Its setup is: stream : PLAYBACK access : MMAP_INTERLEAVED format : S16_LE subformat : STD channels : 2 rate : 48000 exact rate : 48000 (48000/1) msbits : 16 buffer_size : 3072 period_size : 1024 period_time : 21333 tstamp_mode : NONE tstamp_type : MONOTONIC period_step : 1 avail_min : 1024 period_event : 0 start_threshold : 2 stop_threshold : 3072 silence_threshold: 0 silence_size : 0 boundary : 6917529027641081856 Hardware PCM card 1 'HDA Intel PCH' device 0 subdevice 0 Its setup is: stream : PLAYBACK access : MMAP_INTERLEAVED format : S16_LE subformat : STD channels : 2 rate : 48000 exact rate : 48000 (48000/1) msbits : 16 buffer_size : 4096 period_size : 1024 period_time : 21333 tstamp_mode : ENABLE tstamp_type : MONOTONIC period_step : 1 avail_min : 1024 period_event : 0 start_threshold : 1 stop_threshold : 0 silence_threshold: 0 silence_size : 0 boundary : 4611686018427387904 appl_ptr : 0 hw_ptr : 2734916609 frames = 1411 writing whole buffer writing whole buffer writing whole buffer minus 1 frame draining audio alsa_quickcrash: pcm.c:3236: snd_pcm_area_copy: Assertion `src < dst || src >= dst + bytes' failed. Aborted (core dumped) ``` Issue URL : https://github.com/alsa-project/alsa-lib/issues/314 Repository URL: https://github.com/alsa-project/alsa-lib

1 0

Re: linux-6.4 alsa sound broken
by Jaroslav Kysela 04 May '23

04 May '23

On 03. 05. 23 18:10, Takashi Iwai wrote: > On Mon, 01 May 2023 09:17:20 +0200, > Oswald Buddenhagen wrote: >> >> On Mon, May 01, 2023 at 11:59:12AM +0800, Jeff Chua wrote: >>> Latest git pull from Linus's tree ... playing a simple sound file will >>> resulted in a lot of echo. >>> >> how _exactly_ does it sound? >> have you recorded a file through loopback for us to investigate? best >> would be a short sample of a clean wave (sine or sawtooth) with some >> leading and trailing silence. >> >>> Running on Lenovo X1 with .. >>> 00:1f.3 Audio device: Intel Corporation Alder Lake PCH-P High >>> Definition Audio Controller (rev 01) >>> >>> I've bisected and reverted the following patch fixed the problem. >>> >> this seems weird. so my first thought is: are you _sure_ that your >> bisect isn't "contaminated" somehow? is the effect consistent across >> several reboots with the same build? does re-applying my patch >> immediately re-introduce the problem? >> >> - this code is about silencing. getting dropouts or no playback at all >> would be plausible, while echo (that is, repetition) seems surprising. >> theoretically, the driver may be setting a bad fill_silence() >> callback which copies some garbage instead of zeroing, but the HDA >> driver doesn't set one at all (i.e., uses the default one). >> - this code must be explicitly enabled, which for all i know is done >> by almost nothing. what players did you try? did you get consistent >> results? did you try taking out audio servers from the equation? >> - the affected hardware belongs to the extremely widely used HDA >> family, which at the layer the patch is even remotely connected with >> is completely standardized. so _a lot_ of people should be affected, >> and we should be getting reports like yours by the dozen. are we? >> >> of course i can't exclude the possibility that my patch is affected by >> an uninitialized variable or memory corruption (or in the worst case >> causes it), which would of course have very hard to predict >> effects. but that should be investigated properly instead of just >> reverting, lest we might be papering over a much more serious problem. > > Oswald, this looks like a real regression by the patch. > Specially, this happens with dmix, and the issue doesn't seem specific > to the driver. It happens also with USB-audio, not only with > HD-audio. Just aplay /usr/share/sounds/alsa/Side_Left.wav or whatever > there with the dmix config showed the problem. > > The dmix uses the silence_size=boundary as a fill-all operation, and > it's a free-wheel mode, so supposedly something was overlooked in your > code refactoring. > > Could you check it and address quickly? I'd like to fix it before > 6.4-rc1 release, so if no fix comes up in a couple of days, I'll have > to revert the change for 6.4-rc1. I would revert this patch. It seems that this "do silence right after the playback is finished" mechanism is not handled in the updated code (and I overlooked that, too): - ofs = runtime->status->hw_ptr; - frames = new_hw_ptr - ofs; - if ((snd_pcm_sframes_t)frames < 0) - frames += runtime->boundary; - runtime->silence_filled -= frames; - if ((snd_pcm_sframes_t)runtime->silence_filled < 0) { - runtime->silence_filled = 0; - runtime->silence_start = new_hw_ptr; - } else { - runtime->silence_start = ofs; - } It requires to track the old and new hw_ptr, so the removal of the new_hw_ptr argument is not valid. I don't see any easy way to fix this. I would probably fix the snd_pcm_playback_hw_avail() call with the old hw_ptr which seems like the only one issue with the original code, because it makes the threshold inaccurate (it is expected to fill more silent samples). Another issue is wrong silence_start for the incremental silence calls. The patch to fix the original code may look like: diff --git a/sound/core/pcm_lib.c b/sound/core/pcm_lib.c index af1eb136feb0..70795a83e50a 100644 --- a/sound/core/pcm_lib.c +++ b/sound/core/pcm_lib.c @@ -45,7 +45,7 @@ static int fill_silence_frames(struct snd_pcm_substream *substream, void snd_pcm_playback_silence(struct snd_pcm_substream *substream, snd_pcm_uframes_t new_hw_ptr) { struct snd_pcm_runtime *runtime = substream->runtime; - snd_pcm_uframes_t frames, ofs, transfer; + snd_pcm_uframes_t start, frames, ofs, transfer; int err; if (runtime->silence_size < runtime->boundary) { @@ -63,12 +63,17 @@ void snd_pcm_playback_silence(struct snd_pcm_substream *substream, snd_pcm_ufram } if (runtime->silence_filled >= runtime->buffer_size) return; + /* use appl_ptr as a temporary variable */ + appl_ptr = runtime->status->hw_ptr; + runtime->status->hw_ptr = new_hw_ptr; noise_dist = snd_pcm_playback_hw_avail(runtime) + runtime->silence_filled; + runtime->status->hw_ptr = appl_ptr; if (noise_dist >= (snd_pcm_sframes_t) runtime->silence_threshold) return; frames = runtime->silence_threshold - noise_dist; if (frames > runtime->silence_size) frames = runtime->silence_size; + start = (runtime->silence_start + runtime->silence_filled) % runtime->boundary; } else { if (new_hw_ptr == ULONG_MAX) { /* initialization */ snd_pcm_sframes_t avail = snd_pcm_playback_hw_avail(runtime); @@ -92,12 +97,13 @@ void snd_pcm_playback_silence(struct snd_pcm_substream *substream, snd_pcm_ufram } } frames = runtime->buffer_size - runtime->silence_filled; + start = runtime->silence_start; } if (snd_BUG_ON(frames > runtime->buffer_size)) return; if (frames == 0) return; - ofs = runtime->silence_start % runtime->buffer_size; + ofs = start % runtime->buffer_size; while (frames > 0) { transfer = ofs + frames > runtime->buffer_size ? runtime->buffer_size - ofs : frames; err = fill_silence_frames(substream, ofs, transfer); I'll post a complete patch when we agree on this solution. The runtime->status->hw_ptr may not be even preserved, because it is no used in the rest of code in snd_pcm_update_hw_ptr0(), but the code looks more sane. Jaroslav -- Jaroslav Kysela <perex(a)perex.cz> Linux Sound Maintainer; ALSA Project; Red Hat, Inc.

3 3

[PATCH v2] ASoC: codecs: wcd938x: fix accessing regmap on unattached devices
by Krzysztof Kozlowski 04 May '23

04 May '23

The WCD938x comes with three devices on two Linux drivers: 1. RX Soundwire device (wcd938x-sdw.c driver), 2. TX Soundwire device, which is used to access devices via regmap (also wcd938x-sdw.c driver), 3. platform device (wcd938x.c driver) - glue and component master, actually having most of the code using TX Soundwire device regmap. When RX and TX Soundwire devices probe, the component master (platform device) bind tries to write micbias configuration via TX Soundwire regmap. This might happen before TX Soundwire enumerates, so the regmap access fails. On Qualcomm SM8550 board with WCD9385: qcom-soundwire 6d30000.soundwire-controller: Qualcomm Soundwire controller v2.0.0 Registered wcd938x_codec audio-codec: bound sdw:0:0217:010d:00:4 (ops wcd938x_sdw_component_ops) wcd938x_codec audio-codec: bound sdw:0:0217:010d:00:3 (ops wcd938x_sdw_component_ops) qcom-soundwire 6ad0000.soundwire-controller: swrm_wait_for_wr_fifo_avail err write overflow Fix the issue by: 1. Moving the regmap creation from platform device to TX Soundwire device. The regmap settings are moved as-is with one difference: making the wcd938x_regmap_config const. 2. Using regmap in cache only mode till the actual TX Soundwire device enumerates and then sync the regmap cache. Cc: <stable(a)vger.kernel.org> # v3.14+ Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski(a)linaro.org> --- Cc: Pierre-Louis Bossart <pierre-louis.bossart(a)linux.intel.com> Cc: Patrick Lai <quic_plai(a)quicinc.com> Cc: Srinivas Kandagatla <srinivas.kandagatla(a)linaro.org> Changes since v1: 1. Previous solution touched Soundwire. Rework it according to feedback. https://lore.kernel.org/all/20230420101617.142225-7-krzysztof.kozlowski@lin… Thank you Mark and Pierre-Louis for great hints and valuable feedback! --- sound/soc/codecs/wcd938x-sdw.c | 1037 +++++++++++++++++++++++++++++++- sound/soc/codecs/wcd938x.c | 1003 +----------------------------- sound/soc/codecs/wcd938x.h | 1 + 3 files changed, 1030 insertions(+), 1011 deletions(-) diff --git a/sound/soc/codecs/wcd938x-sdw.c b/sound/soc/codecs/wcd938x-sdw.c index 33d1b5ffeaeb..402286dfaea4 100644 --- a/sound/soc/codecs/wcd938x-sdw.c +++ b/sound/soc/codecs/wcd938x-sdw.c @@ -161,6 +161,14 @@ EXPORT_SYMBOL_GPL(wcd938x_sdw_set_sdw_stream); static int wcd9380_update_status(struct sdw_slave *slave, enum sdw_slave_status status) { + struct wcd938x_sdw_priv *wcd = dev_get_drvdata(&slave->dev); + + if (wcd->regmap && (status == SDW_SLAVE_ATTACHED)) { + /* Write out any cached changes that happened between probe and attach */ + regcache_cache_only(wcd->regmap, false); + return regcache_sync(wcd->regmap); + } + return 0; } @@ -177,20 +185,1014 @@ static int wcd9380_interrupt_callback(struct sdw_slave *slave, { struct wcd938x_sdw_priv *wcd = dev_get_drvdata(&slave->dev); struct irq_domain *slave_irq = wcd->slave_irq; - struct regmap *regmap = dev_get_regmap(&slave->dev, NULL); u32 sts1, sts2, sts3; do { handle_nested_irq(irq_find_mapping(slave_irq, 0)); - regmap_read(regmap, WCD938X_DIGITAL_INTR_STATUS_0, &sts1); - regmap_read(regmap, WCD938X_DIGITAL_INTR_STATUS_1, &sts2); - regmap_read(regmap, WCD938X_DIGITAL_INTR_STATUS_2, &sts3); + regmap_read(wcd->regmap, WCD938X_DIGITAL_INTR_STATUS_0, &sts1); + regmap_read(wcd->regmap, WCD938X_DIGITAL_INTR_STATUS_1, &sts2); + regmap_read(wcd->regmap, WCD938X_DIGITAL_INTR_STATUS_2, &sts3); } while (sts1 || sts2 || sts3); return IRQ_HANDLED; } +static const struct reg_default wcd938x_defaults[] = { + {WCD938X_ANA_PAGE_REGISTER, 0x00}, + {WCD938X_ANA_BIAS, 0x00}, + {WCD938X_ANA_RX_SUPPLIES, 0x00}, + {WCD938X_ANA_HPH, 0x0C}, + {WCD938X_ANA_EAR, 0x00}, + {WCD938X_ANA_EAR_COMPANDER_CTL, 0x02}, + {WCD938X_ANA_TX_CH1, 0x20}, + {WCD938X_ANA_TX_CH2, 0x00}, + {WCD938X_ANA_TX_CH3, 0x20}, + {WCD938X_ANA_TX_CH4, 0x00}, + {WCD938X_ANA_MICB1_MICB2_DSP_EN_LOGIC, 0x00}, + {WCD938X_ANA_MICB3_DSP_EN_LOGIC, 0x00}, + {WCD938X_ANA_MBHC_MECH, 0x39}, + {WCD938X_ANA_MBHC_ELECT, 0x08}, + {WCD938X_ANA_MBHC_ZDET, 0x00}, + {WCD938X_ANA_MBHC_RESULT_1, 0x00}, + {WCD938X_ANA_MBHC_RESULT_2, 0x00}, + {WCD938X_ANA_MBHC_RESULT_3, 0x00}, + {WCD938X_ANA_MBHC_BTN0, 0x00}, + {WCD938X_ANA_MBHC_BTN1, 0x10}, + {WCD938X_ANA_MBHC_BTN2, 0x20}, + {WCD938X_ANA_MBHC_BTN3, 0x30}, + {WCD938X_ANA_MBHC_BTN4, 0x40}, + {WCD938X_ANA_MBHC_BTN5, 0x50}, + {WCD938X_ANA_MBHC_BTN6, 0x60}, + {WCD938X_ANA_MBHC_BTN7, 0x70}, + {WCD938X_ANA_MICB1, 0x10}, + {WCD938X_ANA_MICB2, 0x10}, + {WCD938X_ANA_MICB2_RAMP, 0x00}, + {WCD938X_ANA_MICB3, 0x10}, + {WCD938X_ANA_MICB4, 0x10}, + {WCD938X_BIAS_CTL, 0x2A}, + {WCD938X_BIAS_VBG_FINE_ADJ, 0x55}, + {WCD938X_LDOL_VDDCX_ADJUST, 0x01}, + {WCD938X_LDOL_DISABLE_LDOL, 0x00}, + {WCD938X_MBHC_CTL_CLK, 0x00}, + {WCD938X_MBHC_CTL_ANA, 0x00}, + {WCD938X_MBHC_CTL_SPARE_1, 0x00}, + {WCD938X_MBHC_CTL_SPARE_2, 0x00}, + {WCD938X_MBHC_CTL_BCS, 0x00}, + {WCD938X_MBHC_MOISTURE_DET_FSM_STATUS, 0x00}, + {WCD938X_MBHC_TEST_CTL, 0x00}, + {WCD938X_LDOH_MODE, 0x2B}, + {WCD938X_LDOH_BIAS, 0x68}, + {WCD938X_LDOH_STB_LOADS, 0x00}, + {WCD938X_LDOH_SLOWRAMP, 0x50}, + {WCD938X_MICB1_TEST_CTL_1, 0x1A}, + {WCD938X_MICB1_TEST_CTL_2, 0x00}, + {WCD938X_MICB1_TEST_CTL_3, 0xA4}, + {WCD938X_MICB2_TEST_CTL_1, 0x1A}, + {WCD938X_MICB2_TEST_CTL_2, 0x00}, + {WCD938X_MICB2_TEST_CTL_3, 0x24}, + {WCD938X_MICB3_TEST_CTL_1, 0x1A}, + {WCD938X_MICB3_TEST_CTL_2, 0x00}, + {WCD938X_MICB3_TEST_CTL_3, 0xA4}, + {WCD938X_MICB4_TEST_CTL_1, 0x1A}, + {WCD938X_MICB4_TEST_CTL_2, 0x00}, + {WCD938X_MICB4_TEST_CTL_3, 0xA4}, + {WCD938X_TX_COM_ADC_VCM, 0x39}, + {WCD938X_TX_COM_BIAS_ATEST, 0xE0}, + {WCD938X_TX_COM_SPARE1, 0x00}, + {WCD938X_TX_COM_SPARE2, 0x00}, + {WCD938X_TX_COM_TXFE_DIV_CTL, 0x22}, + {WCD938X_TX_COM_TXFE_DIV_START, 0x00}, + {WCD938X_TX_COM_SPARE3, 0x00}, + {WCD938X_TX_COM_SPARE4, 0x00}, + {WCD938X_TX_1_2_TEST_EN, 0xCC}, + {WCD938X_TX_1_2_ADC_IB, 0xE9}, + {WCD938X_TX_1_2_ATEST_REFCTL, 0x0A}, + {WCD938X_TX_1_2_TEST_CTL, 0x38}, + {WCD938X_TX_1_2_TEST_BLK_EN1, 0xFF}, + {WCD938X_TX_1_2_TXFE1_CLKDIV, 0x00}, + {WCD938X_TX_1_2_SAR2_ERR, 0x00}, + {WCD938X_TX_1_2_SAR1_ERR, 0x00}, + {WCD938X_TX_3_4_TEST_EN, 0xCC}, + {WCD938X_TX_3_4_ADC_IB, 0xE9}, + {WCD938X_TX_3_4_ATEST_REFCTL, 0x0A}, + {WCD938X_TX_3_4_TEST_CTL, 0x38}, + {WCD938X_TX_3_4_TEST_BLK_EN3, 0xFF}, + {WCD938X_TX_3_4_TXFE3_CLKDIV, 0x00}, + {WCD938X_TX_3_4_SAR4_ERR, 0x00}, + {WCD938X_TX_3_4_SAR3_ERR, 0x00}, + {WCD938X_TX_3_4_TEST_BLK_EN2, 0xFB}, + {WCD938X_TX_3_4_TXFE2_CLKDIV, 0x00}, + {WCD938X_TX_3_4_SPARE1, 0x00}, + {WCD938X_TX_3_4_TEST_BLK_EN4, 0xFB}, + {WCD938X_TX_3_4_TXFE4_CLKDIV, 0x00}, + {WCD938X_TX_3_4_SPARE2, 0x00}, + {WCD938X_CLASSH_MODE_1, 0x40}, + {WCD938X_CLASSH_MODE_2, 0x3A}, + {WCD938X_CLASSH_MODE_3, 0x00}, + {WCD938X_CLASSH_CTRL_VCL_1, 0x70}, + {WCD938X_CLASSH_CTRL_VCL_2, 0x82}, + {WCD938X_CLASSH_CTRL_CCL_1, 0x31}, + {WCD938X_CLASSH_CTRL_CCL_2, 0x80}, + {WCD938X_CLASSH_CTRL_CCL_3, 0x80}, + {WCD938X_CLASSH_CTRL_CCL_4, 0x51}, + {WCD938X_CLASSH_CTRL_CCL_5, 0x00}, + {WCD938X_CLASSH_BUCK_TMUX_A_D, 0x00}, + {WCD938X_CLASSH_BUCK_SW_DRV_CNTL, 0x77}, + {WCD938X_CLASSH_SPARE, 0x00}, + {WCD938X_FLYBACK_EN, 0x4E}, + {WCD938X_FLYBACK_VNEG_CTRL_1, 0x0B}, + {WCD938X_FLYBACK_VNEG_CTRL_2, 0x45}, + {WCD938X_FLYBACK_VNEG_CTRL_3, 0x74}, + {WCD938X_FLYBACK_VNEG_CTRL_4, 0x7F}, + {WCD938X_FLYBACK_VNEG_CTRL_5, 0x83}, + {WCD938X_FLYBACK_VNEG_CTRL_6, 0x98}, + {WCD938X_FLYBACK_VNEG_CTRL_7, 0xA9}, + {WCD938X_FLYBACK_VNEG_CTRL_8, 0x68}, + {WCD938X_FLYBACK_VNEG_CTRL_9, 0x64}, + {WCD938X_FLYBACK_VNEGDAC_CTRL_1, 0xED}, + {WCD938X_FLYBACK_VNEGDAC_CTRL_2, 0xF0}, + {WCD938X_FLYBACK_VNEGDAC_CTRL_3, 0xA6}, + {WCD938X_FLYBACK_CTRL_1, 0x65}, + {WCD938X_FLYBACK_TEST_CTL, 0x00}, + {WCD938X_RX_AUX_SW_CTL, 0x00}, + {WCD938X_RX_PA_AUX_IN_CONN, 0x01}, + {WCD938X_RX_TIMER_DIV, 0x32}, + {WCD938X_RX_OCP_CTL, 0x1F}, + {WCD938X_RX_OCP_COUNT, 0x77}, + {WCD938X_RX_BIAS_EAR_DAC, 0xA0}, + {WCD938X_RX_BIAS_EAR_AMP, 0xAA}, + {WCD938X_RX_BIAS_HPH_LDO, 0xA9}, + {WCD938X_RX_BIAS_HPH_PA, 0xAA}, + {WCD938X_RX_BIAS_HPH_RDACBUFF_CNP2, 0x8A}, + {WCD938X_RX_BIAS_HPH_RDAC_LDO, 0x88}, + {WCD938X_RX_BIAS_HPH_CNP1, 0x82}, + {WCD938X_RX_BIAS_HPH_LOWPOWER, 0x82}, + {WCD938X_RX_BIAS_AUX_DAC, 0xA0}, + {WCD938X_RX_BIAS_AUX_AMP, 0xAA}, + {WCD938X_RX_BIAS_VNEGDAC_BLEEDER, 0x50}, + {WCD938X_RX_BIAS_MISC, 0x00}, + {WCD938X_RX_BIAS_BUCK_RST, 0x08}, + {WCD938X_RX_BIAS_BUCK_VREF_ERRAMP, 0x44}, + {WCD938X_RX_BIAS_FLYB_ERRAMP, 0x40}, + {WCD938X_RX_BIAS_FLYB_BUFF, 0xAA}, + {WCD938X_RX_BIAS_FLYB_MID_RST, 0x14}, + {WCD938X_HPH_L_STATUS, 0x04}, + {WCD938X_HPH_R_STATUS, 0x04}, + {WCD938X_HPH_CNP_EN, 0x80}, + {WCD938X_HPH_CNP_WG_CTL, 0x9A}, + {WCD938X_HPH_CNP_WG_TIME, 0x14}, + {WCD938X_HPH_OCP_CTL, 0x28}, + {WCD938X_HPH_AUTO_CHOP, 0x16}, + {WCD938X_HPH_CHOP_CTL, 0x83}, + {WCD938X_HPH_PA_CTL1, 0x46}, + {WCD938X_HPH_PA_CTL2, 0x50}, + {WCD938X_HPH_L_EN, 0x80}, + {WCD938X_HPH_L_TEST, 0xE0}, + {WCD938X_HPH_L_ATEST, 0x50}, + {WCD938X_HPH_R_EN, 0x80}, + {WCD938X_HPH_R_TEST, 0xE0}, + {WCD938X_HPH_R_ATEST, 0x54}, + {WCD938X_HPH_RDAC_CLK_CTL1, 0x99}, + {WCD938X_HPH_RDAC_CLK_CTL2, 0x9B}, + {WCD938X_HPH_RDAC_LDO_CTL, 0x33}, + {WCD938X_HPH_RDAC_CHOP_CLK_LP_CTL, 0x00}, + {WCD938X_HPH_REFBUFF_UHQA_CTL, 0x68}, + {WCD938X_HPH_REFBUFF_LP_CTL, 0x0E}, + {WCD938X_HPH_L_DAC_CTL, 0x20}, + {WCD938X_HPH_R_DAC_CTL, 0x20}, + {WCD938X_HPH_SURGE_HPHLR_SURGE_COMP_SEL, 0x55}, + {WCD938X_HPH_SURGE_HPHLR_SURGE_EN, 0x19}, + {WCD938X_HPH_SURGE_HPHLR_SURGE_MISC1, 0xA0}, + {WCD938X_HPH_SURGE_HPHLR_SURGE_STATUS, 0x00}, + {WCD938X_EAR_EAR_EN_REG, 0x22}, + {WCD938X_EAR_EAR_PA_CON, 0x44}, + {WCD938X_EAR_EAR_SP_CON, 0xDB}, + {WCD938X_EAR_EAR_DAC_CON, 0x80}, + {WCD938X_EAR_EAR_CNP_FSM_CON, 0xB2}, + {WCD938X_EAR_TEST_CTL, 0x00}, + {WCD938X_EAR_STATUS_REG_1, 0x00}, + {WCD938X_EAR_STATUS_REG_2, 0x08}, + {WCD938X_ANA_NEW_PAGE_REGISTER, 0x00}, + {WCD938X_HPH_NEW_ANA_HPH2, 0x00}, + {WCD938X_HPH_NEW_ANA_HPH3, 0x00}, + {WCD938X_SLEEP_CTL, 0x16}, + {WCD938X_SLEEP_WATCHDOG_CTL, 0x00}, + {WCD938X_MBHC_NEW_ELECT_REM_CLAMP_CTL, 0x00}, + {WCD938X_MBHC_NEW_CTL_1, 0x02}, + {WCD938X_MBHC_NEW_CTL_2, 0x05}, + {WCD938X_MBHC_NEW_PLUG_DETECT_CTL, 0xE9}, + {WCD938X_MBHC_NEW_ZDET_ANA_CTL, 0x0F}, + {WCD938X_MBHC_NEW_ZDET_RAMP_CTL, 0x00}, + {WCD938X_MBHC_NEW_FSM_STATUS, 0x00}, + {WCD938X_MBHC_NEW_ADC_RESULT, 0x00}, + {WCD938X_TX_NEW_AMIC_MUX_CFG, 0x00}, + {WCD938X_AUX_AUXPA, 0x00}, + {WCD938X_LDORXTX_MODE, 0x0C}, + {WCD938X_LDORXTX_CONFIG, 0x10}, + {WCD938X_DIE_CRACK_DIE_CRK_DET_EN, 0x00}, + {WCD938X_DIE_CRACK_DIE_CRK_DET_OUT, 0x00}, + {WCD938X_HPH_NEW_INT_RDAC_GAIN_CTL, 0x40}, + {WCD938X_HPH_NEW_INT_RDAC_HD2_CTL_L, 0x81}, + {WCD938X_HPH_NEW_INT_RDAC_VREF_CTL, 0x10}, + {WCD938X_HPH_NEW_INT_RDAC_OVERRIDE_CTL, 0x00}, + {WCD938X_HPH_NEW_INT_RDAC_HD2_CTL_R, 0x81}, + {WCD938X_HPH_NEW_INT_PA_MISC1, 0x22}, + {WCD938X_HPH_NEW_INT_PA_MISC2, 0x00}, + {WCD938X_HPH_NEW_INT_PA_RDAC_MISC, 0x00}, + {WCD938X_HPH_NEW_INT_HPH_TIMER1, 0xFE}, + {WCD938X_HPH_NEW_INT_HPH_TIMER2, 0x02}, + {WCD938X_HPH_NEW_INT_HPH_TIMER3, 0x4E}, + {WCD938X_HPH_NEW_INT_HPH_TIMER4, 0x54}, + {WCD938X_HPH_NEW_INT_PA_RDAC_MISC2, 0x00}, + {WCD938X_HPH_NEW_INT_PA_RDAC_MISC3, 0x00}, + {WCD938X_HPH_NEW_INT_RDAC_HD2_CTL_L_NEW, 0x90}, + {WCD938X_HPH_NEW_INT_RDAC_HD2_CTL_R_NEW, 0x90}, + {WCD938X_RX_NEW_INT_HPH_RDAC_BIAS_LOHIFI, 0x62}, + {WCD938X_RX_NEW_INT_HPH_RDAC_BIAS_ULP, 0x01}, + {WCD938X_RX_NEW_INT_HPH_RDAC_LDO_LP, 0x11}, + {WCD938X_MBHC_NEW_INT_MOISTURE_DET_DC_CTRL, 0x57}, + {WCD938X_MBHC_NEW_INT_MOISTURE_DET_POLLING_CTRL, 0x01}, + {WCD938X_MBHC_NEW_INT_MECH_DET_CURRENT, 0x00}, + {WCD938X_MBHC_NEW_INT_SPARE_2, 0x00}, + {WCD938X_EAR_INT_NEW_EAR_CHOPPER_CON, 0xA8}, + {WCD938X_EAR_INT_NEW_CNP_VCM_CON1, 0x42}, + {WCD938X_EAR_INT_NEW_CNP_VCM_CON2, 0x22}, + {WCD938X_EAR_INT_NEW_EAR_DYNAMIC_BIAS, 0x00}, + {WCD938X_AUX_INT_EN_REG, 0x00}, + {WCD938X_AUX_INT_PA_CTRL, 0x06}, + {WCD938X_AUX_INT_SP_CTRL, 0xD2}, + {WCD938X_AUX_INT_DAC_CTRL, 0x80}, + {WCD938X_AUX_INT_CLK_CTRL, 0x50}, + {WCD938X_AUX_INT_TEST_CTRL, 0x00}, + {WCD938X_AUX_INT_STATUS_REG, 0x00}, + {WCD938X_AUX_INT_MISC, 0x00}, + {WCD938X_LDORXTX_INT_BIAS, 0x6E}, + {WCD938X_LDORXTX_INT_STB_LOADS_DTEST, 0x50}, + {WCD938X_LDORXTX_INT_TEST0, 0x1C}, + {WCD938X_LDORXTX_INT_STARTUP_TIMER, 0xFF}, + {WCD938X_LDORXTX_INT_TEST1, 0x1F}, + {WCD938X_LDORXTX_INT_STATUS, 0x00}, + {WCD938X_SLEEP_INT_WATCHDOG_CTL_1, 0x0A}, + {WCD938X_SLEEP_INT_WATCHDOG_CTL_2, 0x0A}, + {WCD938X_DIE_CRACK_INT_DIE_CRK_DET_INT1, 0x02}, + {WCD938X_DIE_CRACK_INT_DIE_CRK_DET_INT2, 0x60}, + {WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_L2, 0xFF}, + {WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_L1, 0x7F}, + {WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_L0, 0x3F}, + {WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_ULP1P2M, 0x1F}, + {WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_ULP0P6M, 0x0F}, + {WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG1_L2L1, 0xD7}, + {WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG1_L0, 0xC8}, + {WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG1_ULP, 0xC6}, + {WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2MAIN_L2L1, 0xD5}, + {WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2MAIN_L0, 0xCA}, + {WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2MAIN_ULP, 0x05}, + {WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2CASC_L2L1L0, 0xA5}, + {WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2CASC_ULP, 0x13}, + {WCD938X_TX_COM_NEW_INT_TXADC_SCBIAS_L2L1, 0x88}, + {WCD938X_TX_COM_NEW_INT_TXADC_SCBIAS_L0ULP, 0x42}, + {WCD938X_TX_COM_NEW_INT_TXADC_INT_L2, 0xFF}, + {WCD938X_TX_COM_NEW_INT_TXADC_INT_L1, 0x64}, + {WCD938X_TX_COM_NEW_INT_TXADC_INT_L0, 0x64}, + {WCD938X_TX_COM_NEW_INT_TXADC_INT_ULP, 0x77}, + {WCD938X_DIGITAL_PAGE_REGISTER, 0x00}, + {WCD938X_DIGITAL_CHIP_ID0, 0x00}, + {WCD938X_DIGITAL_CHIP_ID1, 0x00}, + {WCD938X_DIGITAL_CHIP_ID2, 0x0D}, + {WCD938X_DIGITAL_CHIP_ID3, 0x01}, + {WCD938X_DIGITAL_SWR_TX_CLK_RATE, 0x00}, + {WCD938X_DIGITAL_CDC_RST_CTL, 0x03}, + {WCD938X_DIGITAL_TOP_CLK_CFG, 0x00}, + {WCD938X_DIGITAL_CDC_ANA_CLK_CTL, 0x00}, + {WCD938X_DIGITAL_CDC_DIG_CLK_CTL, 0xF0}, + {WCD938X_DIGITAL_SWR_RST_EN, 0x00}, + {WCD938X_DIGITAL_CDC_PATH_MODE, 0x55}, + {WCD938X_DIGITAL_CDC_RX_RST, 0x00}, + {WCD938X_DIGITAL_CDC_RX0_CTL, 0xFC}, + {WCD938X_DIGITAL_CDC_RX1_CTL, 0xFC}, + {WCD938X_DIGITAL_CDC_RX2_CTL, 0xFC}, + {WCD938X_DIGITAL_CDC_TX_ANA_MODE_0_1, 0x00}, + {WCD938X_DIGITAL_CDC_TX_ANA_MODE_2_3, 0x00}, + {WCD938X_DIGITAL_CDC_COMP_CTL_0, 0x00}, + {WCD938X_DIGITAL_CDC_ANA_TX_CLK_CTL, 0x1E}, + {WCD938X_DIGITAL_CDC_HPH_DSM_A1_0, 0x00}, + {WCD938X_DIGITAL_CDC_HPH_DSM_A1_1, 0x01}, + {WCD938X_DIGITAL_CDC_HPH_DSM_A2_0, 0x63}, + {WCD938X_DIGITAL_CDC_HPH_DSM_A2_1, 0x04}, + {WCD938X_DIGITAL_CDC_HPH_DSM_A3_0, 0xAC}, + {WCD938X_DIGITAL_CDC_HPH_DSM_A3_1, 0x04}, + {WCD938X_DIGITAL_CDC_HPH_DSM_A4_0, 0x1A}, + {WCD938X_DIGITAL_CDC_HPH_DSM_A4_1, 0x03}, + {WCD938X_DIGITAL_CDC_HPH_DSM_A5_0, 0xBC}, + {WCD938X_DIGITAL_CDC_HPH_DSM_A5_1, 0x02}, + {WCD938X_DIGITAL_CDC_HPH_DSM_A6_0, 0xC7}, + {WCD938X_DIGITAL_CDC_HPH_DSM_A7_0, 0xF8}, + {WCD938X_DIGITAL_CDC_HPH_DSM_C_0, 0x47}, + {WCD938X_DIGITAL_CDC_HPH_DSM_C_1, 0x43}, + {WCD938X_DIGITAL_CDC_HPH_DSM_C_2, 0xB1}, + {WCD938X_DIGITAL_CDC_HPH_DSM_C_3, 0x17}, + {WCD938X_DIGITAL_CDC_HPH_DSM_R1, 0x4D}, + {WCD938X_DIGITAL_CDC_HPH_DSM_R2, 0x29}, + {WCD938X_DIGITAL_CDC_HPH_DSM_R3, 0x34}, + {WCD938X_DIGITAL_CDC_HPH_DSM_R4, 0x59}, + {WCD938X_DIGITAL_CDC_HPH_DSM_R5, 0x66}, + {WCD938X_DIGITAL_CDC_HPH_DSM_R6, 0x87}, + {WCD938X_DIGITAL_CDC_HPH_DSM_R7, 0x64}, + {WCD938X_DIGITAL_CDC_AUX_DSM_A1_0, 0x00}, + {WCD938X_DIGITAL_CDC_AUX_DSM_A1_1, 0x01}, + {WCD938X_DIGITAL_CDC_AUX_DSM_A2_0, 0x96}, + {WCD938X_DIGITAL_CDC_AUX_DSM_A2_1, 0x09}, + {WCD938X_DIGITAL_CDC_AUX_DSM_A3_0, 0xAB}, + {WCD938X_DIGITAL_CDC_AUX_DSM_A3_1, 0x05}, + {WCD938X_DIGITAL_CDC_AUX_DSM_A4_0, 0x1C}, + {WCD938X_DIGITAL_CDC_AUX_DSM_A4_1, 0x02}, + {WCD938X_DIGITAL_CDC_AUX_DSM_A5_0, 0x17}, + {WCD938X_DIGITAL_CDC_AUX_DSM_A5_1, 0x02}, + {WCD938X_DIGITAL_CDC_AUX_DSM_A6_0, 0xAA}, + {WCD938X_DIGITAL_CDC_AUX_DSM_A7_0, 0xE3}, + {WCD938X_DIGITAL_CDC_AUX_DSM_C_0, 0x69}, + {WCD938X_DIGITAL_CDC_AUX_DSM_C_1, 0x54}, + {WCD938X_DIGITAL_CDC_AUX_DSM_C_2, 0x02}, + {WCD938X_DIGITAL_CDC_AUX_DSM_C_3, 0x15}, + {WCD938X_DIGITAL_CDC_AUX_DSM_R1, 0xA4}, + {WCD938X_DIGITAL_CDC_AUX_DSM_R2, 0xB5}, + {WCD938X_DIGITAL_CDC_AUX_DSM_R3, 0x86}, + {WCD938X_DIGITAL_CDC_AUX_DSM_R4, 0x85}, + {WCD938X_DIGITAL_CDC_AUX_DSM_R5, 0xAA}, + {WCD938X_DIGITAL_CDC_AUX_DSM_R6, 0xE2}, + {WCD938X_DIGITAL_CDC_AUX_DSM_R7, 0x62}, + {WCD938X_DIGITAL_CDC_HPH_GAIN_RX_0, 0x55}, + {WCD938X_DIGITAL_CDC_HPH_GAIN_RX_1, 0xA9}, + {WCD938X_DIGITAL_CDC_HPH_GAIN_DSD_0, 0x3D}, + {WCD938X_DIGITAL_CDC_HPH_GAIN_DSD_1, 0x2E}, + {WCD938X_DIGITAL_CDC_HPH_GAIN_DSD_2, 0x01}, + {WCD938X_DIGITAL_CDC_AUX_GAIN_DSD_0, 0x00}, + {WCD938X_DIGITAL_CDC_AUX_GAIN_DSD_1, 0xFC}, + {WCD938X_DIGITAL_CDC_AUX_GAIN_DSD_2, 0x01}, + {WCD938X_DIGITAL_CDC_HPH_GAIN_CTL, 0x00}, + {WCD938X_DIGITAL_CDC_AUX_GAIN_CTL, 0x00}, + {WCD938X_DIGITAL_CDC_EAR_PATH_CTL, 0x00}, + {WCD938X_DIGITAL_CDC_SWR_CLH, 0x00}, + {WCD938X_DIGITAL_SWR_CLH_BYP, 0x00}, + {WCD938X_DIGITAL_CDC_TX0_CTL, 0x68}, + {WCD938X_DIGITAL_CDC_TX1_CTL, 0x68}, + {WCD938X_DIGITAL_CDC_TX2_CTL, 0x68}, + {WCD938X_DIGITAL_CDC_TX_RST, 0x00}, + {WCD938X_DIGITAL_CDC_REQ_CTL, 0x01}, + {WCD938X_DIGITAL_CDC_RST, 0x00}, + {WCD938X_DIGITAL_CDC_AMIC_CTL, 0x0F}, + {WCD938X_DIGITAL_CDC_DMIC_CTL, 0x04}, + {WCD938X_DIGITAL_CDC_DMIC1_CTL, 0x01}, + {WCD938X_DIGITAL_CDC_DMIC2_CTL, 0x01}, + {WCD938X_DIGITAL_CDC_DMIC3_CTL, 0x01}, + {WCD938X_DIGITAL_CDC_DMIC4_CTL, 0x01}, + {WCD938X_DIGITAL_EFUSE_PRG_CTL, 0x00}, + {WCD938X_DIGITAL_EFUSE_CTL, 0x2B}, + {WCD938X_DIGITAL_CDC_DMIC_RATE_1_2, 0x11}, + {WCD938X_DIGITAL_CDC_DMIC_RATE_3_4, 0x11}, + {WCD938X_DIGITAL_PDM_WD_CTL0, 0x00}, + {WCD938X_DIGITAL_PDM_WD_CTL1, 0x00}, + {WCD938X_DIGITAL_PDM_WD_CTL2, 0x00}, + {WCD938X_DIGITAL_INTR_MODE, 0x00}, + {WCD938X_DIGITAL_INTR_MASK_0, 0xFF}, + {WCD938X_DIGITAL_INTR_MASK_1, 0xFF}, + {WCD938X_DIGITAL_INTR_MASK_2, 0x3F}, + {WCD938X_DIGITAL_INTR_STATUS_0, 0x00}, + {WCD938X_DIGITAL_INTR_STATUS_1, 0x00}, + {WCD938X_DIGITAL_INTR_STATUS_2, 0x00}, + {WCD938X_DIGITAL_INTR_CLEAR_0, 0x00}, + {WCD938X_DIGITAL_INTR_CLEAR_1, 0x00}, + {WCD938X_DIGITAL_INTR_CLEAR_2, 0x00}, + {WCD938X_DIGITAL_INTR_LEVEL_0, 0x00}, + {WCD938X_DIGITAL_INTR_LEVEL_1, 0x00}, + {WCD938X_DIGITAL_INTR_LEVEL_2, 0x00}, + {WCD938X_DIGITAL_INTR_SET_0, 0x00}, + {WCD938X_DIGITAL_INTR_SET_1, 0x00}, + {WCD938X_DIGITAL_INTR_SET_2, 0x00}, + {WCD938X_DIGITAL_INTR_TEST_0, 0x00}, + {WCD938X_DIGITAL_INTR_TEST_1, 0x00}, + {WCD938X_DIGITAL_INTR_TEST_2, 0x00}, + {WCD938X_DIGITAL_TX_MODE_DBG_EN, 0x00}, + {WCD938X_DIGITAL_TX_MODE_DBG_0_1, 0x00}, + {WCD938X_DIGITAL_TX_MODE_DBG_2_3, 0x00}, + {WCD938X_DIGITAL_LB_IN_SEL_CTL, 0x00}, + {WCD938X_DIGITAL_LOOP_BACK_MODE, 0x00}, + {WCD938X_DIGITAL_SWR_DAC_TEST, 0x00}, + {WCD938X_DIGITAL_SWR_HM_TEST_RX_0, 0x40}, + {WCD938X_DIGITAL_SWR_HM_TEST_TX_0, 0x40}, + {WCD938X_DIGITAL_SWR_HM_TEST_RX_1, 0x00}, + {WCD938X_DIGITAL_SWR_HM_TEST_TX_1, 0x00}, + {WCD938X_DIGITAL_SWR_HM_TEST_TX_2, 0x00}, + {WCD938X_DIGITAL_SWR_HM_TEST_0, 0x00}, + {WCD938X_DIGITAL_SWR_HM_TEST_1, 0x00}, + {WCD938X_DIGITAL_PAD_CTL_SWR_0, 0x8F}, + {WCD938X_DIGITAL_PAD_CTL_SWR_1, 0x06}, + {WCD938X_DIGITAL_I2C_CTL, 0x00}, + {WCD938X_DIGITAL_CDC_TX_TANGGU_SW_MODE, 0x00}, + {WCD938X_DIGITAL_EFUSE_TEST_CTL_0, 0x00}, + {WCD938X_DIGITAL_EFUSE_TEST_CTL_1, 0x00}, + {WCD938X_DIGITAL_EFUSE_T_DATA_0, 0x00}, + {WCD938X_DIGITAL_EFUSE_T_DATA_1, 0x00}, + {WCD938X_DIGITAL_PAD_CTL_PDM_RX0, 0xF1}, + {WCD938X_DIGITAL_PAD_CTL_PDM_RX1, 0xF1}, + {WCD938X_DIGITAL_PAD_CTL_PDM_TX0, 0xF1}, + {WCD938X_DIGITAL_PAD_CTL_PDM_TX1, 0xF1}, + {WCD938X_DIGITAL_PAD_CTL_PDM_TX2, 0xF1}, + {WCD938X_DIGITAL_PAD_INP_DIS_0, 0x00}, + {WCD938X_DIGITAL_PAD_INP_DIS_1, 0x00}, + {WCD938X_DIGITAL_DRIVE_STRENGTH_0, 0x00}, + {WCD938X_DIGITAL_DRIVE_STRENGTH_1, 0x00}, + {WCD938X_DIGITAL_DRIVE_STRENGTH_2, 0x00}, + {WCD938X_DIGITAL_RX_DATA_EDGE_CTL, 0x1F}, + {WCD938X_DIGITAL_TX_DATA_EDGE_CTL, 0x80}, + {WCD938X_DIGITAL_GPIO_MODE, 0x00}, + {WCD938X_DIGITAL_PIN_CTL_OE, 0x00}, + {WCD938X_DIGITAL_PIN_CTL_DATA_0, 0x00}, + {WCD938X_DIGITAL_PIN_CTL_DATA_1, 0x00}, + {WCD938X_DIGITAL_PIN_STATUS_0, 0x00}, + {WCD938X_DIGITAL_PIN_STATUS_1, 0x00}, + {WCD938X_DIGITAL_DIG_DEBUG_CTL, 0x00}, + {WCD938X_DIGITAL_DIG_DEBUG_EN, 0x00}, + {WCD938X_DIGITAL_ANA_CSR_DBG_ADD, 0x00}, + {WCD938X_DIGITAL_ANA_CSR_DBG_CTL, 0x48}, + {WCD938X_DIGITAL_SSP_DBG, 0x00}, + {WCD938X_DIGITAL_MODE_STATUS_0, 0x00}, + {WCD938X_DIGITAL_MODE_STATUS_1, 0x00}, + {WCD938X_DIGITAL_SPARE_0, 0x00}, + {WCD938X_DIGITAL_SPARE_1, 0x00}, + {WCD938X_DIGITAL_SPARE_2, 0x00}, + {WCD938X_DIGITAL_EFUSE_REG_0, 0x00}, + {WCD938X_DIGITAL_EFUSE_REG_1, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_2, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_3, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_4, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_5, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_6, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_7, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_8, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_9, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_10, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_11, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_12, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_13, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_14, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_15, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_16, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_17, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_18, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_19, 0xFF}, + {WCD938X_DIGITAL_EFUSE_REG_20, 0x0E}, + {WCD938X_DIGITAL_EFUSE_REG_21, 0x00}, + {WCD938X_DIGITAL_EFUSE_REG_22, 0x00}, + {WCD938X_DIGITAL_EFUSE_REG_23, 0xF8}, + {WCD938X_DIGITAL_EFUSE_REG_24, 0x16}, + {WCD938X_DIGITAL_EFUSE_REG_25, 0x00}, + {WCD938X_DIGITAL_EFUSE_REG_26, 0x00}, + {WCD938X_DIGITAL_EFUSE_REG_27, 0x00}, + {WCD938X_DIGITAL_EFUSE_REG_28, 0x00}, + {WCD938X_DIGITAL_EFUSE_REG_29, 0x00}, + {WCD938X_DIGITAL_EFUSE_REG_30, 0x00}, + {WCD938X_DIGITAL_EFUSE_REG_31, 0x00}, + {WCD938X_DIGITAL_TX_REQ_FB_CTL_0, 0x88}, + {WCD938X_DIGITAL_TX_REQ_FB_CTL_1, 0x88}, + {WCD938X_DIGITAL_TX_REQ_FB_CTL_2, 0x88}, + {WCD938X_DIGITAL_TX_REQ_FB_CTL_3, 0x88}, + {WCD938X_DIGITAL_TX_REQ_FB_CTL_4, 0x88}, + {WCD938X_DIGITAL_DEM_BYPASS_DATA0, 0x55}, + {WCD938X_DIGITAL_DEM_BYPASS_DATA1, 0x55}, + {WCD938X_DIGITAL_DEM_BYPASS_DATA2, 0x55}, + {WCD938X_DIGITAL_DEM_BYPASS_DATA3, 0x01}, +}; + +static bool wcd938x_rdwr_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case WCD938X_ANA_PAGE_REGISTER: + case WCD938X_ANA_BIAS: + case WCD938X_ANA_RX_SUPPLIES: + case WCD938X_ANA_HPH: + case WCD938X_ANA_EAR: + case WCD938X_ANA_EAR_COMPANDER_CTL: + case WCD938X_ANA_TX_CH1: + case WCD938X_ANA_TX_CH2: + case WCD938X_ANA_TX_CH3: + case WCD938X_ANA_TX_CH4: + case WCD938X_ANA_MICB1_MICB2_DSP_EN_LOGIC: + case WCD938X_ANA_MICB3_DSP_EN_LOGIC: + case WCD938X_ANA_MBHC_MECH: + case WCD938X_ANA_MBHC_ELECT: + case WCD938X_ANA_MBHC_ZDET: + case WCD938X_ANA_MBHC_BTN0: + case WCD938X_ANA_MBHC_BTN1: + case WCD938X_ANA_MBHC_BTN2: + case WCD938X_ANA_MBHC_BTN3: + case WCD938X_ANA_MBHC_BTN4: + case WCD938X_ANA_MBHC_BTN5: + case WCD938X_ANA_MBHC_BTN6: + case WCD938X_ANA_MBHC_BTN7: + case WCD938X_ANA_MICB1: + case WCD938X_ANA_MICB2: + case WCD938X_ANA_MICB2_RAMP: + case WCD938X_ANA_MICB3: + case WCD938X_ANA_MICB4: + case WCD938X_BIAS_CTL: + case WCD938X_BIAS_VBG_FINE_ADJ: + case WCD938X_LDOL_VDDCX_ADJUST: + case WCD938X_LDOL_DISABLE_LDOL: + case WCD938X_MBHC_CTL_CLK: + case WCD938X_MBHC_CTL_ANA: + case WCD938X_MBHC_CTL_SPARE_1: + case WCD938X_MBHC_CTL_SPARE_2: + case WCD938X_MBHC_CTL_BCS: + case WCD938X_MBHC_TEST_CTL: + case WCD938X_LDOH_MODE: + case WCD938X_LDOH_BIAS: + case WCD938X_LDOH_STB_LOADS: + case WCD938X_LDOH_SLOWRAMP: + case WCD938X_MICB1_TEST_CTL_1: + case WCD938X_MICB1_TEST_CTL_2: + case WCD938X_MICB1_TEST_CTL_3: + case WCD938X_MICB2_TEST_CTL_1: + case WCD938X_MICB2_TEST_CTL_2: + case WCD938X_MICB2_TEST_CTL_3: + case WCD938X_MICB3_TEST_CTL_1: + case WCD938X_MICB3_TEST_CTL_2: + case WCD938X_MICB3_TEST_CTL_3: + case WCD938X_MICB4_TEST_CTL_1: + case WCD938X_MICB4_TEST_CTL_2: + case WCD938X_MICB4_TEST_CTL_3: + case WCD938X_TX_COM_ADC_VCM: + case WCD938X_TX_COM_BIAS_ATEST: + case WCD938X_TX_COM_SPARE1: + case WCD938X_TX_COM_SPARE2: + case WCD938X_TX_COM_TXFE_DIV_CTL: + case WCD938X_TX_COM_TXFE_DIV_START: + case WCD938X_TX_COM_SPARE3: + case WCD938X_TX_COM_SPARE4: + case WCD938X_TX_1_2_TEST_EN: + case WCD938X_TX_1_2_ADC_IB: + case WCD938X_TX_1_2_ATEST_REFCTL: + case WCD938X_TX_1_2_TEST_CTL: + case WCD938X_TX_1_2_TEST_BLK_EN1: + case WCD938X_TX_1_2_TXFE1_CLKDIV: + case WCD938X_TX_3_4_TEST_EN: + case WCD938X_TX_3_4_ADC_IB: + case WCD938X_TX_3_4_ATEST_REFCTL: + case WCD938X_TX_3_4_TEST_CTL: + case WCD938X_TX_3_4_TEST_BLK_EN3: + case WCD938X_TX_3_4_TXFE3_CLKDIV: + case WCD938X_TX_3_4_TEST_BLK_EN2: + case WCD938X_TX_3_4_TXFE2_CLKDIV: + case WCD938X_TX_3_4_SPARE1: + case WCD938X_TX_3_4_TEST_BLK_EN4: + case WCD938X_TX_3_4_TXFE4_CLKDIV: + case WCD938X_TX_3_4_SPARE2: + case WCD938X_CLASSH_MODE_1: + case WCD938X_CLASSH_MODE_2: + case WCD938X_CLASSH_MODE_3: + case WCD938X_CLASSH_CTRL_VCL_1: + case WCD938X_CLASSH_CTRL_VCL_2: + case WCD938X_CLASSH_CTRL_CCL_1: + case WCD938X_CLASSH_CTRL_CCL_2: + case WCD938X_CLASSH_CTRL_CCL_3: + case WCD938X_CLASSH_CTRL_CCL_4: + case WCD938X_CLASSH_CTRL_CCL_5: + case WCD938X_CLASSH_BUCK_TMUX_A_D: + case WCD938X_CLASSH_BUCK_SW_DRV_CNTL: + case WCD938X_CLASSH_SPARE: + case WCD938X_FLYBACK_EN: + case WCD938X_FLYBACK_VNEG_CTRL_1: + case WCD938X_FLYBACK_VNEG_CTRL_2: + case WCD938X_FLYBACK_VNEG_CTRL_3: + case WCD938X_FLYBACK_VNEG_CTRL_4: + case WCD938X_FLYBACK_VNEG_CTRL_5: + case WCD938X_FLYBACK_VNEG_CTRL_6: + case WCD938X_FLYBACK_VNEG_CTRL_7: + case WCD938X_FLYBACK_VNEG_CTRL_8: + case WCD938X_FLYBACK_VNEG_CTRL_9: + case WCD938X_FLYBACK_VNEGDAC_CTRL_1: + case WCD938X_FLYBACK_VNEGDAC_CTRL_2: + case WCD938X_FLYBACK_VNEGDAC_CTRL_3: + case WCD938X_FLYBACK_CTRL_1: + case WCD938X_FLYBACK_TEST_CTL: + case WCD938X_RX_AUX_SW_CTL: + case WCD938X_RX_PA_AUX_IN_CONN: + case WCD938X_RX_TIMER_DIV: + case WCD938X_RX_OCP_CTL: + case WCD938X_RX_OCP_COUNT: + case WCD938X_RX_BIAS_EAR_DAC: + case WCD938X_RX_BIAS_EAR_AMP: + case WCD938X_RX_BIAS_HPH_LDO: + case WCD938X_RX_BIAS_HPH_PA: + case WCD938X_RX_BIAS_HPH_RDACBUFF_CNP2: + case WCD938X_RX_BIAS_HPH_RDAC_LDO: + case WCD938X_RX_BIAS_HPH_CNP1: + case WCD938X_RX_BIAS_HPH_LOWPOWER: + case WCD938X_RX_BIAS_AUX_DAC: + case WCD938X_RX_BIAS_AUX_AMP: + case WCD938X_RX_BIAS_VNEGDAC_BLEEDER: + case WCD938X_RX_BIAS_MISC: + case WCD938X_RX_BIAS_BUCK_RST: + case WCD938X_RX_BIAS_BUCK_VREF_ERRAMP: + case WCD938X_RX_BIAS_FLYB_ERRAMP: + case WCD938X_RX_BIAS_FLYB_BUFF: + case WCD938X_RX_BIAS_FLYB_MID_RST: + case WCD938X_HPH_CNP_EN: + case WCD938X_HPH_CNP_WG_CTL: + case WCD938X_HPH_CNP_WG_TIME: + case WCD938X_HPH_OCP_CTL: + case WCD938X_HPH_AUTO_CHOP: + case WCD938X_HPH_CHOP_CTL: + case WCD938X_HPH_PA_CTL1: + case WCD938X_HPH_PA_CTL2: + case WCD938X_HPH_L_EN: + case WCD938X_HPH_L_TEST: + case WCD938X_HPH_L_ATEST: + case WCD938X_HPH_R_EN: + case WCD938X_HPH_R_TEST: + case WCD938X_HPH_R_ATEST: + case WCD938X_HPH_RDAC_CLK_CTL1: + case WCD938X_HPH_RDAC_CLK_CTL2: + case WCD938X_HPH_RDAC_LDO_CTL: + case WCD938X_HPH_RDAC_CHOP_CLK_LP_CTL: + case WCD938X_HPH_REFBUFF_UHQA_CTL: + case WCD938X_HPH_REFBUFF_LP_CTL: + case WCD938X_HPH_L_DAC_CTL: + case WCD938X_HPH_R_DAC_CTL: + case WCD938X_HPH_SURGE_HPHLR_SURGE_COMP_SEL: + case WCD938X_HPH_SURGE_HPHLR_SURGE_EN: + case WCD938X_HPH_SURGE_HPHLR_SURGE_MISC1: + case WCD938X_EAR_EAR_EN_REG: + case WCD938X_EAR_EAR_PA_CON: + case WCD938X_EAR_EAR_SP_CON: + case WCD938X_EAR_EAR_DAC_CON: + case WCD938X_EAR_EAR_CNP_FSM_CON: + case WCD938X_EAR_TEST_CTL: + case WCD938X_ANA_NEW_PAGE_REGISTER: + case WCD938X_HPH_NEW_ANA_HPH2: + case WCD938X_HPH_NEW_ANA_HPH3: + case WCD938X_SLEEP_CTL: + case WCD938X_SLEEP_WATCHDOG_CTL: + case WCD938X_MBHC_NEW_ELECT_REM_CLAMP_CTL: + case WCD938X_MBHC_NEW_CTL_1: + case WCD938X_MBHC_NEW_CTL_2: + case WCD938X_MBHC_NEW_PLUG_DETECT_CTL: + case WCD938X_MBHC_NEW_ZDET_ANA_CTL: + case WCD938X_MBHC_NEW_ZDET_RAMP_CTL: + case WCD938X_TX_NEW_AMIC_MUX_CFG: + case WCD938X_AUX_AUXPA: + case WCD938X_LDORXTX_MODE: + case WCD938X_LDORXTX_CONFIG: + case WCD938X_DIE_CRACK_DIE_CRK_DET_EN: + case WCD938X_HPH_NEW_INT_RDAC_GAIN_CTL: + case WCD938X_HPH_NEW_INT_RDAC_HD2_CTL_L: + case WCD938X_HPH_NEW_INT_RDAC_VREF_CTL: + case WCD938X_HPH_NEW_INT_RDAC_OVERRIDE_CTL: + case WCD938X_HPH_NEW_INT_RDAC_HD2_CTL_R: + case WCD938X_HPH_NEW_INT_PA_MISC1: + case WCD938X_HPH_NEW_INT_PA_MISC2: + case WCD938X_HPH_NEW_INT_PA_RDAC_MISC: + case WCD938X_HPH_NEW_INT_HPH_TIMER1: + case WCD938X_HPH_NEW_INT_HPH_TIMER2: + case WCD938X_HPH_NEW_INT_HPH_TIMER3: + case WCD938X_HPH_NEW_INT_HPH_TIMER4: + case WCD938X_HPH_NEW_INT_PA_RDAC_MISC2: + case WCD938X_HPH_NEW_INT_PA_RDAC_MISC3: + case WCD938X_HPH_NEW_INT_RDAC_HD2_CTL_L_NEW: + case WCD938X_HPH_NEW_INT_RDAC_HD2_CTL_R_NEW: + case WCD938X_RX_NEW_INT_HPH_RDAC_BIAS_LOHIFI: + case WCD938X_RX_NEW_INT_HPH_RDAC_BIAS_ULP: + case WCD938X_RX_NEW_INT_HPH_RDAC_LDO_LP: + case WCD938X_MBHC_NEW_INT_MOISTURE_DET_DC_CTRL: + case WCD938X_MBHC_NEW_INT_MOISTURE_DET_POLLING_CTRL: + case WCD938X_MBHC_NEW_INT_MECH_DET_CURRENT: + case WCD938X_MBHC_NEW_INT_SPARE_2: + case WCD938X_EAR_INT_NEW_EAR_CHOPPER_CON: + case WCD938X_EAR_INT_NEW_CNP_VCM_CON1: + case WCD938X_EAR_INT_NEW_CNP_VCM_CON2: + case WCD938X_EAR_INT_NEW_EAR_DYNAMIC_BIAS: + case WCD938X_AUX_INT_EN_REG: + case WCD938X_AUX_INT_PA_CTRL: + case WCD938X_AUX_INT_SP_CTRL: + case WCD938X_AUX_INT_DAC_CTRL: + case WCD938X_AUX_INT_CLK_CTRL: + case WCD938X_AUX_INT_TEST_CTRL: + case WCD938X_AUX_INT_MISC: + case WCD938X_LDORXTX_INT_BIAS: + case WCD938X_LDORXTX_INT_STB_LOADS_DTEST: + case WCD938X_LDORXTX_INT_TEST0: + case WCD938X_LDORXTX_INT_STARTUP_TIMER: + case WCD938X_LDORXTX_INT_TEST1: + case WCD938X_SLEEP_INT_WATCHDOG_CTL_1: + case WCD938X_SLEEP_INT_WATCHDOG_CTL_2: + case WCD938X_DIE_CRACK_INT_DIE_CRK_DET_INT1: + case WCD938X_DIE_CRACK_INT_DIE_CRK_DET_INT2: + case WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_L2: + case WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_L1: + case WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_L0: + case WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_ULP1P2M: + case WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_ULP0P6M: + case WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG1_L2L1: + case WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG1_L0: + case WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG1_ULP: + case WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2MAIN_L2L1: + case WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2MAIN_L0: + case WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2MAIN_ULP: + case WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2CASC_L2L1L0: + case WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2CASC_ULP: + case WCD938X_TX_COM_NEW_INT_TXADC_SCBIAS_L2L1: + case WCD938X_TX_COM_NEW_INT_TXADC_SCBIAS_L0ULP: + case WCD938X_TX_COM_NEW_INT_TXADC_INT_L2: + case WCD938X_TX_COM_NEW_INT_TXADC_INT_L1: + case WCD938X_TX_COM_NEW_INT_TXADC_INT_L0: + case WCD938X_TX_COM_NEW_INT_TXADC_INT_ULP: + case WCD938X_DIGITAL_PAGE_REGISTER: + case WCD938X_DIGITAL_SWR_TX_CLK_RATE: + case WCD938X_DIGITAL_CDC_RST_CTL: + case WCD938X_DIGITAL_TOP_CLK_CFG: + case WCD938X_DIGITAL_CDC_ANA_CLK_CTL: + case WCD938X_DIGITAL_CDC_DIG_CLK_CTL: + case WCD938X_DIGITAL_SWR_RST_EN: + case WCD938X_DIGITAL_CDC_PATH_MODE: + case WCD938X_DIGITAL_CDC_RX_RST: + case WCD938X_DIGITAL_CDC_RX0_CTL: + case WCD938X_DIGITAL_CDC_RX1_CTL: + case WCD938X_DIGITAL_CDC_RX2_CTL: + case WCD938X_DIGITAL_CDC_TX_ANA_MODE_0_1: + case WCD938X_DIGITAL_CDC_TX_ANA_MODE_2_3: + case WCD938X_DIGITAL_CDC_COMP_CTL_0: + case WCD938X_DIGITAL_CDC_ANA_TX_CLK_CTL: + case WCD938X_DIGITAL_CDC_HPH_DSM_A1_0: + case WCD938X_DIGITAL_CDC_HPH_DSM_A1_1: + case WCD938X_DIGITAL_CDC_HPH_DSM_A2_0: + case WCD938X_DIGITAL_CDC_HPH_DSM_A2_1: + case WCD938X_DIGITAL_CDC_HPH_DSM_A3_0: + case WCD938X_DIGITAL_CDC_HPH_DSM_A3_1: + case WCD938X_DIGITAL_CDC_HPH_DSM_A4_0: + case WCD938X_DIGITAL_CDC_HPH_DSM_A4_1: + case WCD938X_DIGITAL_CDC_HPH_DSM_A5_0: + case WCD938X_DIGITAL_CDC_HPH_DSM_A5_1: + case WCD938X_DIGITAL_CDC_HPH_DSM_A6_0: + case WCD938X_DIGITAL_CDC_HPH_DSM_A7_0: + case WCD938X_DIGITAL_CDC_HPH_DSM_C_0: + case WCD938X_DIGITAL_CDC_HPH_DSM_C_1: + case WCD938X_DIGITAL_CDC_HPH_DSM_C_2: + case WCD938X_DIGITAL_CDC_HPH_DSM_C_3: + case WCD938X_DIGITAL_CDC_HPH_DSM_R1: + case WCD938X_DIGITAL_CDC_HPH_DSM_R2: + case WCD938X_DIGITAL_CDC_HPH_DSM_R3: + case WCD938X_DIGITAL_CDC_HPH_DSM_R4: + case WCD938X_DIGITAL_CDC_HPH_DSM_R5: + case WCD938X_DIGITAL_CDC_HPH_DSM_R6: + case WCD938X_DIGITAL_CDC_HPH_DSM_R7: + case WCD938X_DIGITAL_CDC_AUX_DSM_A1_0: + case WCD938X_DIGITAL_CDC_AUX_DSM_A1_1: + case WCD938X_DIGITAL_CDC_AUX_DSM_A2_0: + case WCD938X_DIGITAL_CDC_AUX_DSM_A2_1: + case WCD938X_DIGITAL_CDC_AUX_DSM_A3_0: + case WCD938X_DIGITAL_CDC_AUX_DSM_A3_1: + case WCD938X_DIGITAL_CDC_AUX_DSM_A4_0: + case WCD938X_DIGITAL_CDC_AUX_DSM_A4_1: + case WCD938X_DIGITAL_CDC_AUX_DSM_A5_0: + case WCD938X_DIGITAL_CDC_AUX_DSM_A5_1: + case WCD938X_DIGITAL_CDC_AUX_DSM_A6_0: + case WCD938X_DIGITAL_CDC_AUX_DSM_A7_0: + case WCD938X_DIGITAL_CDC_AUX_DSM_C_0: + case WCD938X_DIGITAL_CDC_AUX_DSM_C_1: + case WCD938X_DIGITAL_CDC_AUX_DSM_C_2: + case WCD938X_DIGITAL_CDC_AUX_DSM_C_3: + case WCD938X_DIGITAL_CDC_AUX_DSM_R1: + case WCD938X_DIGITAL_CDC_AUX_DSM_R2: + case WCD938X_DIGITAL_CDC_AUX_DSM_R3: + case WCD938X_DIGITAL_CDC_AUX_DSM_R4: + case WCD938X_DIGITAL_CDC_AUX_DSM_R5: + case WCD938X_DIGITAL_CDC_AUX_DSM_R6: + case WCD938X_DIGITAL_CDC_AUX_DSM_R7: + case WCD938X_DIGITAL_CDC_HPH_GAIN_RX_0: + case WCD938X_DIGITAL_CDC_HPH_GAIN_RX_1: + case WCD938X_DIGITAL_CDC_HPH_GAIN_DSD_0: + case WCD938X_DIGITAL_CDC_HPH_GAIN_DSD_1: + case WCD938X_DIGITAL_CDC_HPH_GAIN_DSD_2: + case WCD938X_DIGITAL_CDC_AUX_GAIN_DSD_0: + case WCD938X_DIGITAL_CDC_AUX_GAIN_DSD_1: + case WCD938X_DIGITAL_CDC_AUX_GAIN_DSD_2: + case WCD938X_DIGITAL_CDC_HPH_GAIN_CTL: + case WCD938X_DIGITAL_CDC_AUX_GAIN_CTL: + case WCD938X_DIGITAL_CDC_EAR_PATH_CTL: + case WCD938X_DIGITAL_CDC_SWR_CLH: + case WCD938X_DIGITAL_SWR_CLH_BYP: + case WCD938X_DIGITAL_CDC_TX0_CTL: + case WCD938X_DIGITAL_CDC_TX1_CTL: + case WCD938X_DIGITAL_CDC_TX2_CTL: + case WCD938X_DIGITAL_CDC_TX_RST: + case WCD938X_DIGITAL_CDC_REQ_CTL: + case WCD938X_DIGITAL_CDC_RST: + case WCD938X_DIGITAL_CDC_AMIC_CTL: + case WCD938X_DIGITAL_CDC_DMIC_CTL: + case WCD938X_DIGITAL_CDC_DMIC1_CTL: + case WCD938X_DIGITAL_CDC_DMIC2_CTL: + case WCD938X_DIGITAL_CDC_DMIC3_CTL: + case WCD938X_DIGITAL_CDC_DMIC4_CTL: + case WCD938X_DIGITAL_EFUSE_PRG_CTL: + case WCD938X_DIGITAL_EFUSE_CTL: + case WCD938X_DIGITAL_CDC_DMIC_RATE_1_2: + case WCD938X_DIGITAL_CDC_DMIC_RATE_3_4: + case WCD938X_DIGITAL_PDM_WD_CTL0: + case WCD938X_DIGITAL_PDM_WD_CTL1: + case WCD938X_DIGITAL_PDM_WD_CTL2: + case WCD938X_DIGITAL_INTR_MODE: + case WCD938X_DIGITAL_INTR_MASK_0: + case WCD938X_DIGITAL_INTR_MASK_1: + case WCD938X_DIGITAL_INTR_MASK_2: + case WCD938X_DIGITAL_INTR_CLEAR_0: + case WCD938X_DIGITAL_INTR_CLEAR_1: + case WCD938X_DIGITAL_INTR_CLEAR_2: + case WCD938X_DIGITAL_INTR_LEVEL_0: + case WCD938X_DIGITAL_INTR_LEVEL_1: + case WCD938X_DIGITAL_INTR_LEVEL_2: + case WCD938X_DIGITAL_INTR_SET_0: + case WCD938X_DIGITAL_INTR_SET_1: + case WCD938X_DIGITAL_INTR_SET_2: + case WCD938X_DIGITAL_INTR_TEST_0: + case WCD938X_DIGITAL_INTR_TEST_1: + case WCD938X_DIGITAL_INTR_TEST_2: + case WCD938X_DIGITAL_TX_MODE_DBG_EN: + case WCD938X_DIGITAL_TX_MODE_DBG_0_1: + case WCD938X_DIGITAL_TX_MODE_DBG_2_3: + case WCD938X_DIGITAL_LB_IN_SEL_CTL: + case WCD938X_DIGITAL_LOOP_BACK_MODE: + case WCD938X_DIGITAL_SWR_DAC_TEST: + case WCD938X_DIGITAL_SWR_HM_TEST_RX_0: + case WCD938X_DIGITAL_SWR_HM_TEST_TX_0: + case WCD938X_DIGITAL_SWR_HM_TEST_RX_1: + case WCD938X_DIGITAL_SWR_HM_TEST_TX_1: + case WCD938X_DIGITAL_SWR_HM_TEST_TX_2: + case WCD938X_DIGITAL_PAD_CTL_SWR_0: + case WCD938X_DIGITAL_PAD_CTL_SWR_1: + case WCD938X_DIGITAL_I2C_CTL: + case WCD938X_DIGITAL_CDC_TX_TANGGU_SW_MODE: + case WCD938X_DIGITAL_EFUSE_TEST_CTL_0: + case WCD938X_DIGITAL_EFUSE_TEST_CTL_1: + case WCD938X_DIGITAL_PAD_CTL_PDM_RX0: + case WCD938X_DIGITAL_PAD_CTL_PDM_RX1: + case WCD938X_DIGITAL_PAD_CTL_PDM_TX0: + case WCD938X_DIGITAL_PAD_CTL_PDM_TX1: + case WCD938X_DIGITAL_PAD_CTL_PDM_TX2: + case WCD938X_DIGITAL_PAD_INP_DIS_0: + case WCD938X_DIGITAL_PAD_INP_DIS_1: + case WCD938X_DIGITAL_DRIVE_STRENGTH_0: + case WCD938X_DIGITAL_DRIVE_STRENGTH_1: + case WCD938X_DIGITAL_DRIVE_STRENGTH_2: + case WCD938X_DIGITAL_RX_DATA_EDGE_CTL: + case WCD938X_DIGITAL_TX_DATA_EDGE_CTL: + case WCD938X_DIGITAL_GPIO_MODE: + case WCD938X_DIGITAL_PIN_CTL_OE: + case WCD938X_DIGITAL_PIN_CTL_DATA_0: + case WCD938X_DIGITAL_PIN_CTL_DATA_1: + case WCD938X_DIGITAL_DIG_DEBUG_CTL: + case WCD938X_DIGITAL_DIG_DEBUG_EN: + case WCD938X_DIGITAL_ANA_CSR_DBG_ADD: + case WCD938X_DIGITAL_ANA_CSR_DBG_CTL: + case WCD938X_DIGITAL_SSP_DBG: + case WCD938X_DIGITAL_SPARE_0: + case WCD938X_DIGITAL_SPARE_1: + case WCD938X_DIGITAL_SPARE_2: + case WCD938X_DIGITAL_TX_REQ_FB_CTL_0: + case WCD938X_DIGITAL_TX_REQ_FB_CTL_1: + case WCD938X_DIGITAL_TX_REQ_FB_CTL_2: + case WCD938X_DIGITAL_TX_REQ_FB_CTL_3: + case WCD938X_DIGITAL_TX_REQ_FB_CTL_4: + case WCD938X_DIGITAL_DEM_BYPASS_DATA0: + case WCD938X_DIGITAL_DEM_BYPASS_DATA1: + case WCD938X_DIGITAL_DEM_BYPASS_DATA2: + case WCD938X_DIGITAL_DEM_BYPASS_DATA3: + return true; + } + + return false; +} + +static bool wcd938x_readonly_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case WCD938X_ANA_MBHC_RESULT_1: + case WCD938X_ANA_MBHC_RESULT_2: + case WCD938X_ANA_MBHC_RESULT_3: + case WCD938X_MBHC_MOISTURE_DET_FSM_STATUS: + case WCD938X_TX_1_2_SAR2_ERR: + case WCD938X_TX_1_2_SAR1_ERR: + case WCD938X_TX_3_4_SAR4_ERR: + case WCD938X_TX_3_4_SAR3_ERR: + case WCD938X_HPH_L_STATUS: + case WCD938X_HPH_R_STATUS: + case WCD938X_HPH_SURGE_HPHLR_SURGE_STATUS: + case WCD938X_EAR_STATUS_REG_1: + case WCD938X_EAR_STATUS_REG_2: + case WCD938X_MBHC_NEW_FSM_STATUS: + case WCD938X_MBHC_NEW_ADC_RESULT: + case WCD938X_DIE_CRACK_DIE_CRK_DET_OUT: + case WCD938X_AUX_INT_STATUS_REG: + case WCD938X_LDORXTX_INT_STATUS: + case WCD938X_DIGITAL_CHIP_ID0: + case WCD938X_DIGITAL_CHIP_ID1: + case WCD938X_DIGITAL_CHIP_ID2: + case WCD938X_DIGITAL_CHIP_ID3: + case WCD938X_DIGITAL_INTR_STATUS_0: + case WCD938X_DIGITAL_INTR_STATUS_1: + case WCD938X_DIGITAL_INTR_STATUS_2: + case WCD938X_DIGITAL_INTR_CLEAR_0: + case WCD938X_DIGITAL_INTR_CLEAR_1: + case WCD938X_DIGITAL_INTR_CLEAR_2: + case WCD938X_DIGITAL_SWR_HM_TEST_0: + case WCD938X_DIGITAL_SWR_HM_TEST_1: + case WCD938X_DIGITAL_EFUSE_T_DATA_0: + case WCD938X_DIGITAL_EFUSE_T_DATA_1: + case WCD938X_DIGITAL_PIN_STATUS_0: + case WCD938X_DIGITAL_PIN_STATUS_1: + case WCD938X_DIGITAL_MODE_STATUS_0: + case WCD938X_DIGITAL_MODE_STATUS_1: + case WCD938X_DIGITAL_EFUSE_REG_0: + case WCD938X_DIGITAL_EFUSE_REG_1: + case WCD938X_DIGITAL_EFUSE_REG_2: + case WCD938X_DIGITAL_EFUSE_REG_3: + case WCD938X_DIGITAL_EFUSE_REG_4: + case WCD938X_DIGITAL_EFUSE_REG_5: + case WCD938X_DIGITAL_EFUSE_REG_6: + case WCD938X_DIGITAL_EFUSE_REG_7: + case WCD938X_DIGITAL_EFUSE_REG_8: + case WCD938X_DIGITAL_EFUSE_REG_9: + case WCD938X_DIGITAL_EFUSE_REG_10: + case WCD938X_DIGITAL_EFUSE_REG_11: + case WCD938X_DIGITAL_EFUSE_REG_12: + case WCD938X_DIGITAL_EFUSE_REG_13: + case WCD938X_DIGITAL_EFUSE_REG_14: + case WCD938X_DIGITAL_EFUSE_REG_15: + case WCD938X_DIGITAL_EFUSE_REG_16: + case WCD938X_DIGITAL_EFUSE_REG_17: + case WCD938X_DIGITAL_EFUSE_REG_18: + case WCD938X_DIGITAL_EFUSE_REG_19: + case WCD938X_DIGITAL_EFUSE_REG_20: + case WCD938X_DIGITAL_EFUSE_REG_21: + case WCD938X_DIGITAL_EFUSE_REG_22: + case WCD938X_DIGITAL_EFUSE_REG_23: + case WCD938X_DIGITAL_EFUSE_REG_24: + case WCD938X_DIGITAL_EFUSE_REG_25: + case WCD938X_DIGITAL_EFUSE_REG_26: + case WCD938X_DIGITAL_EFUSE_REG_27: + case WCD938X_DIGITAL_EFUSE_REG_28: + case WCD938X_DIGITAL_EFUSE_REG_29: + case WCD938X_DIGITAL_EFUSE_REG_30: + case WCD938X_DIGITAL_EFUSE_REG_31: + return true; + } + return false; +} + +static bool wcd938x_readable_register(struct device *dev, unsigned int reg) +{ + bool ret; + + ret = wcd938x_readonly_register(dev, reg); + if (!ret) + return wcd938x_rdwr_register(dev, reg); + + return ret; +} + +static bool wcd938x_writeable_register(struct device *dev, unsigned int reg) +{ + return wcd938x_rdwr_register(dev, reg); +} + +static bool wcd938x_volatile_register(struct device *dev, unsigned int reg) +{ + if (reg <= WCD938X_BASE_ADDRESS) + return false; + + if (reg == WCD938X_DIGITAL_SWR_TX_CLK_RATE) + return true; + + if (wcd938x_readonly_register(dev, reg)) + return true; + + return false; +} + +static const struct regmap_config wcd938x_regmap_config = { + .name = "wcd938x_csr", + .reg_bits = 32, + .val_bits = 8, + .cache_type = REGCACHE_RBTREE, + .reg_defaults = wcd938x_defaults, + .num_reg_defaults = ARRAY_SIZE(wcd938x_defaults), + .max_register = WCD938X_MAX_REGISTER, + .readable_reg = wcd938x_readable_register, + .writeable_reg = wcd938x_writeable_register, + .volatile_reg = wcd938x_volatile_register, + .can_multi_write = true, +}; + static const struct sdw_slave_ops wcd9380_slave_ops = { .update_status = wcd9380_update_status, .interrupt_callback = wcd9380_interrupt_callback, @@ -261,6 +1263,16 @@ static int wcd9380_probe(struct sdw_slave *pdev, wcd->ch_info = &wcd938x_sdw_rx_ch_info[0]; } + if (wcd->is_tx) { + wcd->regmap = devm_regmap_init_sdw(pdev, &wcd938x_regmap_config); + if (IS_ERR(wcd->regmap)) + return dev_err_probe(dev, PTR_ERR(wcd->regmap), + "Regmap init failed\n"); + + /* Start in cache-only until device is enumerated */ + regcache_cache_only(wcd->regmap, true); + }; + pm_runtime_set_autosuspend_delay(dev, 3000); pm_runtime_use_autosuspend(dev); pm_runtime_mark_last_busy(dev); @@ -278,22 +1290,23 @@ MODULE_DEVICE_TABLE(sdw, wcd9380_slave_id); static int __maybe_unused wcd938x_sdw_runtime_suspend(struct device *dev) { - struct regmap *regmap = dev_get_regmap(dev, NULL); + struct wcd938x_sdw_priv *wcd = dev_get_drvdata(dev); - if (regmap) { - regcache_cache_only(regmap, true); - regcache_mark_dirty(regmap); + if (wcd->regmap) { + regcache_cache_only(wcd->regmap, true); + regcache_mark_dirty(wcd->regmap); } + return 0; } static int __maybe_unused wcd938x_sdw_runtime_resume(struct device *dev) { - struct regmap *regmap = dev_get_regmap(dev, NULL); + struct wcd938x_sdw_priv *wcd = dev_get_drvdata(dev); - if (regmap) { - regcache_cache_only(regmap, false); - regcache_sync(regmap); + if (wcd->regmap) { + regcache_cache_only(wcd->regmap, false); + regcache_sync(wcd->regmap); } pm_runtime_mark_last_busy(dev); diff --git a/sound/soc/codecs/wcd938x.c b/sound/soc/codecs/wcd938x.c index 11b264a63b04..e7d6a02cdec0 100644 --- a/sound/soc/codecs/wcd938x.c +++ b/sound/soc/codecs/wcd938x.c @@ -273,1001 +273,6 @@ static struct wcd_mbhc_field wcd_mbhc_fields[WCD_MBHC_REG_FUNC_MAX] = { WCD_MBHC_FIELD(WCD_MBHC_ELECT_ISRC_EN, WCD938X_ANA_MBHC_ZDET, 0x02), }; -static const struct reg_default wcd938x_defaults[] = { - {WCD938X_ANA_PAGE_REGISTER, 0x00}, - {WCD938X_ANA_BIAS, 0x00}, - {WCD938X_ANA_RX_SUPPLIES, 0x00}, - {WCD938X_ANA_HPH, 0x0C}, - {WCD938X_ANA_EAR, 0x00}, - {WCD938X_ANA_EAR_COMPANDER_CTL, 0x02}, - {WCD938X_ANA_TX_CH1, 0x20}, - {WCD938X_ANA_TX_CH2, 0x00}, - {WCD938X_ANA_TX_CH3, 0x20}, - {WCD938X_ANA_TX_CH4, 0x00}, - {WCD938X_ANA_MICB1_MICB2_DSP_EN_LOGIC, 0x00}, - {WCD938X_ANA_MICB3_DSP_EN_LOGIC, 0x00}, - {WCD938X_ANA_MBHC_MECH, 0x39}, - {WCD938X_ANA_MBHC_ELECT, 0x08}, - {WCD938X_ANA_MBHC_ZDET, 0x00}, - {WCD938X_ANA_MBHC_RESULT_1, 0x00}, - {WCD938X_ANA_MBHC_RESULT_2, 0x00}, - {WCD938X_ANA_MBHC_RESULT_3, 0x00}, - {WCD938X_ANA_MBHC_BTN0, 0x00}, - {WCD938X_ANA_MBHC_BTN1, 0x10}, - {WCD938X_ANA_MBHC_BTN2, 0x20}, - {WCD938X_ANA_MBHC_BTN3, 0x30}, - {WCD938X_ANA_MBHC_BTN4, 0x40}, - {WCD938X_ANA_MBHC_BTN5, 0x50}, - {WCD938X_ANA_MBHC_BTN6, 0x60}, - {WCD938X_ANA_MBHC_BTN7, 0x70}, - {WCD938X_ANA_MICB1, 0x10}, - {WCD938X_ANA_MICB2, 0x10}, - {WCD938X_ANA_MICB2_RAMP, 0x00}, - {WCD938X_ANA_MICB3, 0x10}, - {WCD938X_ANA_MICB4, 0x10}, - {WCD938X_BIAS_CTL, 0x2A}, - {WCD938X_BIAS_VBG_FINE_ADJ, 0x55}, - {WCD938X_LDOL_VDDCX_ADJUST, 0x01}, - {WCD938X_LDOL_DISABLE_LDOL, 0x00}, - {WCD938X_MBHC_CTL_CLK, 0x00}, - {WCD938X_MBHC_CTL_ANA, 0x00}, - {WCD938X_MBHC_CTL_SPARE_1, 0x00}, - {WCD938X_MBHC_CTL_SPARE_2, 0x00}, - {WCD938X_MBHC_CTL_BCS, 0x00}, - {WCD938X_MBHC_MOISTURE_DET_FSM_STATUS, 0x00}, - {WCD938X_MBHC_TEST_CTL, 0x00}, - {WCD938X_LDOH_MODE, 0x2B}, - {WCD938X_LDOH_BIAS, 0x68}, - {WCD938X_LDOH_STB_LOADS, 0x00}, - {WCD938X_LDOH_SLOWRAMP, 0x50}, - {WCD938X_MICB1_TEST_CTL_1, 0x1A}, - {WCD938X_MICB1_TEST_CTL_2, 0x00}, - {WCD938X_MICB1_TEST_CTL_3, 0xA4}, - {WCD938X_MICB2_TEST_CTL_1, 0x1A}, - {WCD938X_MICB2_TEST_CTL_2, 0x00}, - {WCD938X_MICB2_TEST_CTL_3, 0x24}, - {WCD938X_MICB3_TEST_CTL_1, 0x1A}, - {WCD938X_MICB3_TEST_CTL_2, 0x00}, - {WCD938X_MICB3_TEST_CTL_3, 0xA4}, - {WCD938X_MICB4_TEST_CTL_1, 0x1A}, - {WCD938X_MICB4_TEST_CTL_2, 0x00}, - {WCD938X_MICB4_TEST_CTL_3, 0xA4}, - {WCD938X_TX_COM_ADC_VCM, 0x39}, - {WCD938X_TX_COM_BIAS_ATEST, 0xE0}, - {WCD938X_TX_COM_SPARE1, 0x00}, - {WCD938X_TX_COM_SPARE2, 0x00}, - {WCD938X_TX_COM_TXFE_DIV_CTL, 0x22}, - {WCD938X_TX_COM_TXFE_DIV_START, 0x00}, - {WCD938X_TX_COM_SPARE3, 0x00}, - {WCD938X_TX_COM_SPARE4, 0x00}, - {WCD938X_TX_1_2_TEST_EN, 0xCC}, - {WCD938X_TX_1_2_ADC_IB, 0xE9}, - {WCD938X_TX_1_2_ATEST_REFCTL, 0x0A}, - {WCD938X_TX_1_2_TEST_CTL, 0x38}, - {WCD938X_TX_1_2_TEST_BLK_EN1, 0xFF}, - {WCD938X_TX_1_2_TXFE1_CLKDIV, 0x00}, - {WCD938X_TX_1_2_SAR2_ERR, 0x00}, - {WCD938X_TX_1_2_SAR1_ERR, 0x00}, - {WCD938X_TX_3_4_TEST_EN, 0xCC}, - {WCD938X_TX_3_4_ADC_IB, 0xE9}, - {WCD938X_TX_3_4_ATEST_REFCTL, 0x0A}, - {WCD938X_TX_3_4_TEST_CTL, 0x38}, - {WCD938X_TX_3_4_TEST_BLK_EN3, 0xFF}, - {WCD938X_TX_3_4_TXFE3_CLKDIV, 0x00}, - {WCD938X_TX_3_4_SAR4_ERR, 0x00}, - {WCD938X_TX_3_4_SAR3_ERR, 0x00}, - {WCD938X_TX_3_4_TEST_BLK_EN2, 0xFB}, - {WCD938X_TX_3_4_TXFE2_CLKDIV, 0x00}, - {WCD938X_TX_3_4_SPARE1, 0x00}, - {WCD938X_TX_3_4_TEST_BLK_EN4, 0xFB}, - {WCD938X_TX_3_4_TXFE4_CLKDIV, 0x00}, - {WCD938X_TX_3_4_SPARE2, 0x00}, - {WCD938X_CLASSH_MODE_1, 0x40}, - {WCD938X_CLASSH_MODE_2, 0x3A}, - {WCD938X_CLASSH_MODE_3, 0x00}, - {WCD938X_CLASSH_CTRL_VCL_1, 0x70}, - {WCD938X_CLASSH_CTRL_VCL_2, 0x82}, - {WCD938X_CLASSH_CTRL_CCL_1, 0x31}, - {WCD938X_CLASSH_CTRL_CCL_2, 0x80}, - {WCD938X_CLASSH_CTRL_CCL_3, 0x80}, - {WCD938X_CLASSH_CTRL_CCL_4, 0x51}, - {WCD938X_CLASSH_CTRL_CCL_5, 0x00}, - {WCD938X_CLASSH_BUCK_TMUX_A_D, 0x00}, - {WCD938X_CLASSH_BUCK_SW_DRV_CNTL, 0x77}, - {WCD938X_CLASSH_SPARE, 0x00}, - {WCD938X_FLYBACK_EN, 0x4E}, - {WCD938X_FLYBACK_VNEG_CTRL_1, 0x0B}, - {WCD938X_FLYBACK_VNEG_CTRL_2, 0x45}, - {WCD938X_FLYBACK_VNEG_CTRL_3, 0x74}, - {WCD938X_FLYBACK_VNEG_CTRL_4, 0x7F}, - {WCD938X_FLYBACK_VNEG_CTRL_5, 0x83}, - {WCD938X_FLYBACK_VNEG_CTRL_6, 0x98}, - {WCD938X_FLYBACK_VNEG_CTRL_7, 0xA9}, - {WCD938X_FLYBACK_VNEG_CTRL_8, 0x68}, - {WCD938X_FLYBACK_VNEG_CTRL_9, 0x64}, - {WCD938X_FLYBACK_VNEGDAC_CTRL_1, 0xED}, - {WCD938X_FLYBACK_VNEGDAC_CTRL_2, 0xF0}, - {WCD938X_FLYBACK_VNEGDAC_CTRL_3, 0xA6}, - {WCD938X_FLYBACK_CTRL_1, 0x65}, - {WCD938X_FLYBACK_TEST_CTL, 0x00}, - {WCD938X_RX_AUX_SW_CTL, 0x00}, - {WCD938X_RX_PA_AUX_IN_CONN, 0x01}, - {WCD938X_RX_TIMER_DIV, 0x32}, - {WCD938X_RX_OCP_CTL, 0x1F}, - {WCD938X_RX_OCP_COUNT, 0x77}, - {WCD938X_RX_BIAS_EAR_DAC, 0xA0}, - {WCD938X_RX_BIAS_EAR_AMP, 0xAA}, - {WCD938X_RX_BIAS_HPH_LDO, 0xA9}, - {WCD938X_RX_BIAS_HPH_PA, 0xAA}, - {WCD938X_RX_BIAS_HPH_RDACBUFF_CNP2, 0x8A}, - {WCD938X_RX_BIAS_HPH_RDAC_LDO, 0x88}, - {WCD938X_RX_BIAS_HPH_CNP1, 0x82}, - {WCD938X_RX_BIAS_HPH_LOWPOWER, 0x82}, - {WCD938X_RX_BIAS_AUX_DAC, 0xA0}, - {WCD938X_RX_BIAS_AUX_AMP, 0xAA}, - {WCD938X_RX_BIAS_VNEGDAC_BLEEDER, 0x50}, - {WCD938X_RX_BIAS_MISC, 0x00}, - {WCD938X_RX_BIAS_BUCK_RST, 0x08}, - {WCD938X_RX_BIAS_BUCK_VREF_ERRAMP, 0x44}, - {WCD938X_RX_BIAS_FLYB_ERRAMP, 0x40}, - {WCD938X_RX_BIAS_FLYB_BUFF, 0xAA}, - {WCD938X_RX_BIAS_FLYB_MID_RST, 0x14}, - {WCD938X_HPH_L_STATUS, 0x04}, - {WCD938X_HPH_R_STATUS, 0x04}, - {WCD938X_HPH_CNP_EN, 0x80}, - {WCD938X_HPH_CNP_WG_CTL, 0x9A}, - {WCD938X_HPH_CNP_WG_TIME, 0x14}, - {WCD938X_HPH_OCP_CTL, 0x28}, - {WCD938X_HPH_AUTO_CHOP, 0x16}, - {WCD938X_HPH_CHOP_CTL, 0x83}, - {WCD938X_HPH_PA_CTL1, 0x46}, - {WCD938X_HPH_PA_CTL2, 0x50}, - {WCD938X_HPH_L_EN, 0x80}, - {WCD938X_HPH_L_TEST, 0xE0}, - {WCD938X_HPH_L_ATEST, 0x50}, - {WCD938X_HPH_R_EN, 0x80}, - {WCD938X_HPH_R_TEST, 0xE0}, - {WCD938X_HPH_R_ATEST, 0x54}, - {WCD938X_HPH_RDAC_CLK_CTL1, 0x99}, - {WCD938X_HPH_RDAC_CLK_CTL2, 0x9B}, - {WCD938X_HPH_RDAC_LDO_CTL, 0x33}, - {WCD938X_HPH_RDAC_CHOP_CLK_LP_CTL, 0x00}, - {WCD938X_HPH_REFBUFF_UHQA_CTL, 0x68}, - {WCD938X_HPH_REFBUFF_LP_CTL, 0x0E}, - {WCD938X_HPH_L_DAC_CTL, 0x20}, - {WCD938X_HPH_R_DAC_CTL, 0x20}, - {WCD938X_HPH_SURGE_HPHLR_SURGE_COMP_SEL, 0x55}, - {WCD938X_HPH_SURGE_HPHLR_SURGE_EN, 0x19}, - {WCD938X_HPH_SURGE_HPHLR_SURGE_MISC1, 0xA0}, - {WCD938X_HPH_SURGE_HPHLR_SURGE_STATUS, 0x00}, - {WCD938X_EAR_EAR_EN_REG, 0x22}, - {WCD938X_EAR_EAR_PA_CON, 0x44}, - {WCD938X_EAR_EAR_SP_CON, 0xDB}, - {WCD938X_EAR_EAR_DAC_CON, 0x80}, - {WCD938X_EAR_EAR_CNP_FSM_CON, 0xB2}, - {WCD938X_EAR_TEST_CTL, 0x00}, - {WCD938X_EAR_STATUS_REG_1, 0x00}, - {WCD938X_EAR_STATUS_REG_2, 0x08}, - {WCD938X_ANA_NEW_PAGE_REGISTER, 0x00}, - {WCD938X_HPH_NEW_ANA_HPH2, 0x00}, - {WCD938X_HPH_NEW_ANA_HPH3, 0x00}, - {WCD938X_SLEEP_CTL, 0x16}, - {WCD938X_SLEEP_WATCHDOG_CTL, 0x00}, - {WCD938X_MBHC_NEW_ELECT_REM_CLAMP_CTL, 0x00}, - {WCD938X_MBHC_NEW_CTL_1, 0x02}, - {WCD938X_MBHC_NEW_CTL_2, 0x05}, - {WCD938X_MBHC_NEW_PLUG_DETECT_CTL, 0xE9}, - {WCD938X_MBHC_NEW_ZDET_ANA_CTL, 0x0F}, - {WCD938X_MBHC_NEW_ZDET_RAMP_CTL, 0x00}, - {WCD938X_MBHC_NEW_FSM_STATUS, 0x00}, - {WCD938X_MBHC_NEW_ADC_RESULT, 0x00}, - {WCD938X_TX_NEW_AMIC_MUX_CFG, 0x00}, - {WCD938X_AUX_AUXPA, 0x00}, - {WCD938X_LDORXTX_MODE, 0x0C}, - {WCD938X_LDORXTX_CONFIG, 0x10}, - {WCD938X_DIE_CRACK_DIE_CRK_DET_EN, 0x00}, - {WCD938X_DIE_CRACK_DIE_CRK_DET_OUT, 0x00}, - {WCD938X_HPH_NEW_INT_RDAC_GAIN_CTL, 0x40}, - {WCD938X_HPH_NEW_INT_RDAC_HD2_CTL_L, 0x81}, - {WCD938X_HPH_NEW_INT_RDAC_VREF_CTL, 0x10}, - {WCD938X_HPH_NEW_INT_RDAC_OVERRIDE_CTL, 0x00}, - {WCD938X_HPH_NEW_INT_RDAC_HD2_CTL_R, 0x81}, - {WCD938X_HPH_NEW_INT_PA_MISC1, 0x22}, - {WCD938X_HPH_NEW_INT_PA_MISC2, 0x00}, - {WCD938X_HPH_NEW_INT_PA_RDAC_MISC, 0x00}, - {WCD938X_HPH_NEW_INT_HPH_TIMER1, 0xFE}, - {WCD938X_HPH_NEW_INT_HPH_TIMER2, 0x02}, - {WCD938X_HPH_NEW_INT_HPH_TIMER3, 0x4E}, - {WCD938X_HPH_NEW_INT_HPH_TIMER4, 0x54}, - {WCD938X_HPH_NEW_INT_PA_RDAC_MISC2, 0x00}, - {WCD938X_HPH_NEW_INT_PA_RDAC_MISC3, 0x00}, - {WCD938X_HPH_NEW_INT_RDAC_HD2_CTL_L_NEW, 0x90}, - {WCD938X_HPH_NEW_INT_RDAC_HD2_CTL_R_NEW, 0x90}, - {WCD938X_RX_NEW_INT_HPH_RDAC_BIAS_LOHIFI, 0x62}, - {WCD938X_RX_NEW_INT_HPH_RDAC_BIAS_ULP, 0x01}, - {WCD938X_RX_NEW_INT_HPH_RDAC_LDO_LP, 0x11}, - {WCD938X_MBHC_NEW_INT_MOISTURE_DET_DC_CTRL, 0x57}, - {WCD938X_MBHC_NEW_INT_MOISTURE_DET_POLLING_CTRL, 0x01}, - {WCD938X_MBHC_NEW_INT_MECH_DET_CURRENT, 0x00}, - {WCD938X_MBHC_NEW_INT_SPARE_2, 0x00}, - {WCD938X_EAR_INT_NEW_EAR_CHOPPER_CON, 0xA8}, - {WCD938X_EAR_INT_NEW_CNP_VCM_CON1, 0x42}, - {WCD938X_EAR_INT_NEW_CNP_VCM_CON2, 0x22}, - {WCD938X_EAR_INT_NEW_EAR_DYNAMIC_BIAS, 0x00}, - {WCD938X_AUX_INT_EN_REG, 0x00}, - {WCD938X_AUX_INT_PA_CTRL, 0x06}, - {WCD938X_AUX_INT_SP_CTRL, 0xD2}, - {WCD938X_AUX_INT_DAC_CTRL, 0x80}, - {WCD938X_AUX_INT_CLK_CTRL, 0x50}, - {WCD938X_AUX_INT_TEST_CTRL, 0x00}, - {WCD938X_AUX_INT_STATUS_REG, 0x00}, - {WCD938X_AUX_INT_MISC, 0x00}, - {WCD938X_LDORXTX_INT_BIAS, 0x6E}, - {WCD938X_LDORXTX_INT_STB_LOADS_DTEST, 0x50}, - {WCD938X_LDORXTX_INT_TEST0, 0x1C}, - {WCD938X_LDORXTX_INT_STARTUP_TIMER, 0xFF}, - {WCD938X_LDORXTX_INT_TEST1, 0x1F}, - {WCD938X_LDORXTX_INT_STATUS, 0x00}, - {WCD938X_SLEEP_INT_WATCHDOG_CTL_1, 0x0A}, - {WCD938X_SLEEP_INT_WATCHDOG_CTL_2, 0x0A}, - {WCD938X_DIE_CRACK_INT_DIE_CRK_DET_INT1, 0x02}, - {WCD938X_DIE_CRACK_INT_DIE_CRK_DET_INT2, 0x60}, - {WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_L2, 0xFF}, - {WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_L1, 0x7F}, - {WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_L0, 0x3F}, - {WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_ULP1P2M, 0x1F}, - {WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_ULP0P6M, 0x0F}, - {WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG1_L2L1, 0xD7}, - {WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG1_L0, 0xC8}, - {WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG1_ULP, 0xC6}, - {WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2MAIN_L2L1, 0xD5}, - {WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2MAIN_L0, 0xCA}, - {WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2MAIN_ULP, 0x05}, - {WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2CASC_L2L1L0, 0xA5}, - {WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2CASC_ULP, 0x13}, - {WCD938X_TX_COM_NEW_INT_TXADC_SCBIAS_L2L1, 0x88}, - {WCD938X_TX_COM_NEW_INT_TXADC_SCBIAS_L0ULP, 0x42}, - {WCD938X_TX_COM_NEW_INT_TXADC_INT_L2, 0xFF}, - {WCD938X_TX_COM_NEW_INT_TXADC_INT_L1, 0x64}, - {WCD938X_TX_COM_NEW_INT_TXADC_INT_L0, 0x64}, - {WCD938X_TX_COM_NEW_INT_TXADC_INT_ULP, 0x77}, - {WCD938X_DIGITAL_PAGE_REGISTER, 0x00}, - {WCD938X_DIGITAL_CHIP_ID0, 0x00}, - {WCD938X_DIGITAL_CHIP_ID1, 0x00}, - {WCD938X_DIGITAL_CHIP_ID2, 0x0D}, - {WCD938X_DIGITAL_CHIP_ID3, 0x01}, - {WCD938X_DIGITAL_SWR_TX_CLK_RATE, 0x00}, - {WCD938X_DIGITAL_CDC_RST_CTL, 0x03}, - {WCD938X_DIGITAL_TOP_CLK_CFG, 0x00}, - {WCD938X_DIGITAL_CDC_ANA_CLK_CTL, 0x00}, - {WCD938X_DIGITAL_CDC_DIG_CLK_CTL, 0xF0}, - {WCD938X_DIGITAL_SWR_RST_EN, 0x00}, - {WCD938X_DIGITAL_CDC_PATH_MODE, 0x55}, - {WCD938X_DIGITAL_CDC_RX_RST, 0x00}, - {WCD938X_DIGITAL_CDC_RX0_CTL, 0xFC}, - {WCD938X_DIGITAL_CDC_RX1_CTL, 0xFC}, - {WCD938X_DIGITAL_CDC_RX2_CTL, 0xFC}, - {WCD938X_DIGITAL_CDC_TX_ANA_MODE_0_1, 0x00}, - {WCD938X_DIGITAL_CDC_TX_ANA_MODE_2_3, 0x00}, - {WCD938X_DIGITAL_CDC_COMP_CTL_0, 0x00}, - {WCD938X_DIGITAL_CDC_ANA_TX_CLK_CTL, 0x1E}, - {WCD938X_DIGITAL_CDC_HPH_DSM_A1_0, 0x00}, - {WCD938X_DIGITAL_CDC_HPH_DSM_A1_1, 0x01}, - {WCD938X_DIGITAL_CDC_HPH_DSM_A2_0, 0x63}, - {WCD938X_DIGITAL_CDC_HPH_DSM_A2_1, 0x04}, - {WCD938X_DIGITAL_CDC_HPH_DSM_A3_0, 0xAC}, - {WCD938X_DIGITAL_CDC_HPH_DSM_A3_1, 0x04}, - {WCD938X_DIGITAL_CDC_HPH_DSM_A4_0, 0x1A}, - {WCD938X_DIGITAL_CDC_HPH_DSM_A4_1, 0x03}, - {WCD938X_DIGITAL_CDC_HPH_DSM_A5_0, 0xBC}, - {WCD938X_DIGITAL_CDC_HPH_DSM_A5_1, 0x02}, - {WCD938X_DIGITAL_CDC_HPH_DSM_A6_0, 0xC7}, - {WCD938X_DIGITAL_CDC_HPH_DSM_A7_0, 0xF8}, - {WCD938X_DIGITAL_CDC_HPH_DSM_C_0, 0x47}, - {WCD938X_DIGITAL_CDC_HPH_DSM_C_1, 0x43}, - {WCD938X_DIGITAL_CDC_HPH_DSM_C_2, 0xB1}, - {WCD938X_DIGITAL_CDC_HPH_DSM_C_3, 0x17}, - {WCD938X_DIGITAL_CDC_HPH_DSM_R1, 0x4D}, - {WCD938X_DIGITAL_CDC_HPH_DSM_R2, 0x29}, - {WCD938X_DIGITAL_CDC_HPH_DSM_R3, 0x34}, - {WCD938X_DIGITAL_CDC_HPH_DSM_R4, 0x59}, - {WCD938X_DIGITAL_CDC_HPH_DSM_R5, 0x66}, - {WCD938X_DIGITAL_CDC_HPH_DSM_R6, 0x87}, - {WCD938X_DIGITAL_CDC_HPH_DSM_R7, 0x64}, - {WCD938X_DIGITAL_CDC_AUX_DSM_A1_0, 0x00}, - {WCD938X_DIGITAL_CDC_AUX_DSM_A1_1, 0x01}, - {WCD938X_DIGITAL_CDC_AUX_DSM_A2_0, 0x96}, - {WCD938X_DIGITAL_CDC_AUX_DSM_A2_1, 0x09}, - {WCD938X_DIGITAL_CDC_AUX_DSM_A3_0, 0xAB}, - {WCD938X_DIGITAL_CDC_AUX_DSM_A3_1, 0x05}, - {WCD938X_DIGITAL_CDC_AUX_DSM_A4_0, 0x1C}, - {WCD938X_DIGITAL_CDC_AUX_DSM_A4_1, 0x02}, - {WCD938X_DIGITAL_CDC_AUX_DSM_A5_0, 0x17}, - {WCD938X_DIGITAL_CDC_AUX_DSM_A5_1, 0x02}, - {WCD938X_DIGITAL_CDC_AUX_DSM_A6_0, 0xAA}, - {WCD938X_DIGITAL_CDC_AUX_DSM_A7_0, 0xE3}, - {WCD938X_DIGITAL_CDC_AUX_DSM_C_0, 0x69}, - {WCD938X_DIGITAL_CDC_AUX_DSM_C_1, 0x54}, - {WCD938X_DIGITAL_CDC_AUX_DSM_C_2, 0x02}, - {WCD938X_DIGITAL_CDC_AUX_DSM_C_3, 0x15}, - {WCD938X_DIGITAL_CDC_AUX_DSM_R1, 0xA4}, - {WCD938X_DIGITAL_CDC_AUX_DSM_R2, 0xB5}, - {WCD938X_DIGITAL_CDC_AUX_DSM_R3, 0x86}, - {WCD938X_DIGITAL_CDC_AUX_DSM_R4, 0x85}, - {WCD938X_DIGITAL_CDC_AUX_DSM_R5, 0xAA}, - {WCD938X_DIGITAL_CDC_AUX_DSM_R6, 0xE2}, - {WCD938X_DIGITAL_CDC_AUX_DSM_R7, 0x62}, - {WCD938X_DIGITAL_CDC_HPH_GAIN_RX_0, 0x55}, - {WCD938X_DIGITAL_CDC_HPH_GAIN_RX_1, 0xA9}, - {WCD938X_DIGITAL_CDC_HPH_GAIN_DSD_0, 0x3D}, - {WCD938X_DIGITAL_CDC_HPH_GAIN_DSD_1, 0x2E}, - {WCD938X_DIGITAL_CDC_HPH_GAIN_DSD_2, 0x01}, - {WCD938X_DIGITAL_CDC_AUX_GAIN_DSD_0, 0x00}, - {WCD938X_DIGITAL_CDC_AUX_GAIN_DSD_1, 0xFC}, - {WCD938X_DIGITAL_CDC_AUX_GAIN_DSD_2, 0x01}, - {WCD938X_DIGITAL_CDC_HPH_GAIN_CTL, 0x00}, - {WCD938X_DIGITAL_CDC_AUX_GAIN_CTL, 0x00}, - {WCD938X_DIGITAL_CDC_EAR_PATH_CTL, 0x00}, - {WCD938X_DIGITAL_CDC_SWR_CLH, 0x00}, - {WCD938X_DIGITAL_SWR_CLH_BYP, 0x00}, - {WCD938X_DIGITAL_CDC_TX0_CTL, 0x68}, - {WCD938X_DIGITAL_CDC_TX1_CTL, 0x68}, - {WCD938X_DIGITAL_CDC_TX2_CTL, 0x68}, - {WCD938X_DIGITAL_CDC_TX_RST, 0x00}, - {WCD938X_DIGITAL_CDC_REQ_CTL, 0x01}, - {WCD938X_DIGITAL_CDC_RST, 0x00}, - {WCD938X_DIGITAL_CDC_AMIC_CTL, 0x0F}, - {WCD938X_DIGITAL_CDC_DMIC_CTL, 0x04}, - {WCD938X_DIGITAL_CDC_DMIC1_CTL, 0x01}, - {WCD938X_DIGITAL_CDC_DMIC2_CTL, 0x01}, - {WCD938X_DIGITAL_CDC_DMIC3_CTL, 0x01}, - {WCD938X_DIGITAL_CDC_DMIC4_CTL, 0x01}, - {WCD938X_DIGITAL_EFUSE_PRG_CTL, 0x00}, - {WCD938X_DIGITAL_EFUSE_CTL, 0x2B}, - {WCD938X_DIGITAL_CDC_DMIC_RATE_1_2, 0x11}, - {WCD938X_DIGITAL_CDC_DMIC_RATE_3_4, 0x11}, - {WCD938X_DIGITAL_PDM_WD_CTL0, 0x00}, - {WCD938X_DIGITAL_PDM_WD_CTL1, 0x00}, - {WCD938X_DIGITAL_PDM_WD_CTL2, 0x00}, - {WCD938X_DIGITAL_INTR_MODE, 0x00}, - {WCD938X_DIGITAL_INTR_MASK_0, 0xFF}, - {WCD938X_DIGITAL_INTR_MASK_1, 0xFF}, - {WCD938X_DIGITAL_INTR_MASK_2, 0x3F}, - {WCD938X_DIGITAL_INTR_STATUS_0, 0x00}, - {WCD938X_DIGITAL_INTR_STATUS_1, 0x00}, - {WCD938X_DIGITAL_INTR_STATUS_2, 0x00}, - {WCD938X_DIGITAL_INTR_CLEAR_0, 0x00}, - {WCD938X_DIGITAL_INTR_CLEAR_1, 0x00}, - {WCD938X_DIGITAL_INTR_CLEAR_2, 0x00}, - {WCD938X_DIGITAL_INTR_LEVEL_0, 0x00}, - {WCD938X_DIGITAL_INTR_LEVEL_1, 0x00}, - {WCD938X_DIGITAL_INTR_LEVEL_2, 0x00}, - {WCD938X_DIGITAL_INTR_SET_0, 0x00}, - {WCD938X_DIGITAL_INTR_SET_1, 0x00}, - {WCD938X_DIGITAL_INTR_SET_2, 0x00}, - {WCD938X_DIGITAL_INTR_TEST_0, 0x00}, - {WCD938X_DIGITAL_INTR_TEST_1, 0x00}, - {WCD938X_DIGITAL_INTR_TEST_2, 0x00}, - {WCD938X_DIGITAL_TX_MODE_DBG_EN, 0x00}, - {WCD938X_DIGITAL_TX_MODE_DBG_0_1, 0x00}, - {WCD938X_DIGITAL_TX_MODE_DBG_2_3, 0x00}, - {WCD938X_DIGITAL_LB_IN_SEL_CTL, 0x00}, - {WCD938X_DIGITAL_LOOP_BACK_MODE, 0x00}, - {WCD938X_DIGITAL_SWR_DAC_TEST, 0x00}, - {WCD938X_DIGITAL_SWR_HM_TEST_RX_0, 0x40}, - {WCD938X_DIGITAL_SWR_HM_TEST_TX_0, 0x40}, - {WCD938X_DIGITAL_SWR_HM_TEST_RX_1, 0x00}, - {WCD938X_DIGITAL_SWR_HM_TEST_TX_1, 0x00}, - {WCD938X_DIGITAL_SWR_HM_TEST_TX_2, 0x00}, - {WCD938X_DIGITAL_SWR_HM_TEST_0, 0x00}, - {WCD938X_DIGITAL_SWR_HM_TEST_1, 0x00}, - {WCD938X_DIGITAL_PAD_CTL_SWR_0, 0x8F}, - {WCD938X_DIGITAL_PAD_CTL_SWR_1, 0x06}, - {WCD938X_DIGITAL_I2C_CTL, 0x00}, - {WCD938X_DIGITAL_CDC_TX_TANGGU_SW_MODE, 0x00}, - {WCD938X_DIGITAL_EFUSE_TEST_CTL_0, 0x00}, - {WCD938X_DIGITAL_EFUSE_TEST_CTL_1, 0x00}, - {WCD938X_DIGITAL_EFUSE_T_DATA_0, 0x00}, - {WCD938X_DIGITAL_EFUSE_T_DATA_1, 0x00}, - {WCD938X_DIGITAL_PAD_CTL_PDM_RX0, 0xF1}, - {WCD938X_DIGITAL_PAD_CTL_PDM_RX1, 0xF1}, - {WCD938X_DIGITAL_PAD_CTL_PDM_TX0, 0xF1}, - {WCD938X_DIGITAL_PAD_CTL_PDM_TX1, 0xF1}, - {WCD938X_DIGITAL_PAD_CTL_PDM_TX2, 0xF1}, - {WCD938X_DIGITAL_PAD_INP_DIS_0, 0x00}, - {WCD938X_DIGITAL_PAD_INP_DIS_1, 0x00}, - {WCD938X_DIGITAL_DRIVE_STRENGTH_0, 0x00}, - {WCD938X_DIGITAL_DRIVE_STRENGTH_1, 0x00}, - {WCD938X_DIGITAL_DRIVE_STRENGTH_2, 0x00}, - {WCD938X_DIGITAL_RX_DATA_EDGE_CTL, 0x1F}, - {WCD938X_DIGITAL_TX_DATA_EDGE_CTL, 0x80}, - {WCD938X_DIGITAL_GPIO_MODE, 0x00}, - {WCD938X_DIGITAL_PIN_CTL_OE, 0x00}, - {WCD938X_DIGITAL_PIN_CTL_DATA_0, 0x00}, - {WCD938X_DIGITAL_PIN_CTL_DATA_1, 0x00}, - {WCD938X_DIGITAL_PIN_STATUS_0, 0x00}, - {WCD938X_DIGITAL_PIN_STATUS_1, 0x00}, - {WCD938X_DIGITAL_DIG_DEBUG_CTL, 0x00}, - {WCD938X_DIGITAL_DIG_DEBUG_EN, 0x00}, - {WCD938X_DIGITAL_ANA_CSR_DBG_ADD, 0x00}, - {WCD938X_DIGITAL_ANA_CSR_DBG_CTL, 0x48}, - {WCD938X_DIGITAL_SSP_DBG, 0x00}, - {WCD938X_DIGITAL_MODE_STATUS_0, 0x00}, - {WCD938X_DIGITAL_MODE_STATUS_1, 0x00}, - {WCD938X_DIGITAL_SPARE_0, 0x00}, - {WCD938X_DIGITAL_SPARE_1, 0x00}, - {WCD938X_DIGITAL_SPARE_2, 0x00}, - {WCD938X_DIGITAL_EFUSE_REG_0, 0x00}, - {WCD938X_DIGITAL_EFUSE_REG_1, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_2, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_3, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_4, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_5, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_6, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_7, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_8, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_9, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_10, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_11, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_12, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_13, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_14, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_15, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_16, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_17, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_18, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_19, 0xFF}, - {WCD938X_DIGITAL_EFUSE_REG_20, 0x0E}, - {WCD938X_DIGITAL_EFUSE_REG_21, 0x00}, - {WCD938X_DIGITAL_EFUSE_REG_22, 0x00}, - {WCD938X_DIGITAL_EFUSE_REG_23, 0xF8}, - {WCD938X_DIGITAL_EFUSE_REG_24, 0x16}, - {WCD938X_DIGITAL_EFUSE_REG_25, 0x00}, - {WCD938X_DIGITAL_EFUSE_REG_26, 0x00}, - {WCD938X_DIGITAL_EFUSE_REG_27, 0x00}, - {WCD938X_DIGITAL_EFUSE_REG_28, 0x00}, - {WCD938X_DIGITAL_EFUSE_REG_29, 0x00}, - {WCD938X_DIGITAL_EFUSE_REG_30, 0x00}, - {WCD938X_DIGITAL_EFUSE_REG_31, 0x00}, - {WCD938X_DIGITAL_TX_REQ_FB_CTL_0, 0x88}, - {WCD938X_DIGITAL_TX_REQ_FB_CTL_1, 0x88}, - {WCD938X_DIGITAL_TX_REQ_FB_CTL_2, 0x88}, - {WCD938X_DIGITAL_TX_REQ_FB_CTL_3, 0x88}, - {WCD938X_DIGITAL_TX_REQ_FB_CTL_4, 0x88}, - {WCD938X_DIGITAL_DEM_BYPASS_DATA0, 0x55}, - {WCD938X_DIGITAL_DEM_BYPASS_DATA1, 0x55}, - {WCD938X_DIGITAL_DEM_BYPASS_DATA2, 0x55}, - {WCD938X_DIGITAL_DEM_BYPASS_DATA3, 0x01}, -}; - -static bool wcd938x_rdwr_register(struct device *dev, unsigned int reg) -{ - switch (reg) { - case WCD938X_ANA_PAGE_REGISTER: - case WCD938X_ANA_BIAS: - case WCD938X_ANA_RX_SUPPLIES: - case WCD938X_ANA_HPH: - case WCD938X_ANA_EAR: - case WCD938X_ANA_EAR_COMPANDER_CTL: - case WCD938X_ANA_TX_CH1: - case WCD938X_ANA_TX_CH2: - case WCD938X_ANA_TX_CH3: - case WCD938X_ANA_TX_CH4: - case WCD938X_ANA_MICB1_MICB2_DSP_EN_LOGIC: - case WCD938X_ANA_MICB3_DSP_EN_LOGIC: - case WCD938X_ANA_MBHC_MECH: - case WCD938X_ANA_MBHC_ELECT: - case WCD938X_ANA_MBHC_ZDET: - case WCD938X_ANA_MBHC_BTN0: - case WCD938X_ANA_MBHC_BTN1: - case WCD938X_ANA_MBHC_BTN2: - case WCD938X_ANA_MBHC_BTN3: - case WCD938X_ANA_MBHC_BTN4: - case WCD938X_ANA_MBHC_BTN5: - case WCD938X_ANA_MBHC_BTN6: - case WCD938X_ANA_MBHC_BTN7: - case WCD938X_ANA_MICB1: - case WCD938X_ANA_MICB2: - case WCD938X_ANA_MICB2_RAMP: - case WCD938X_ANA_MICB3: - case WCD938X_ANA_MICB4: - case WCD938X_BIAS_CTL: - case WCD938X_BIAS_VBG_FINE_ADJ: - case WCD938X_LDOL_VDDCX_ADJUST: - case WCD938X_LDOL_DISABLE_LDOL: - case WCD938X_MBHC_CTL_CLK: - case WCD938X_MBHC_CTL_ANA: - case WCD938X_MBHC_CTL_SPARE_1: - case WCD938X_MBHC_CTL_SPARE_2: - case WCD938X_MBHC_CTL_BCS: - case WCD938X_MBHC_TEST_CTL: - case WCD938X_LDOH_MODE: - case WCD938X_LDOH_BIAS: - case WCD938X_LDOH_STB_LOADS: - case WCD938X_LDOH_SLOWRAMP: - case WCD938X_MICB1_TEST_CTL_1: - case WCD938X_MICB1_TEST_CTL_2: - case WCD938X_MICB1_TEST_CTL_3: - case WCD938X_MICB2_TEST_CTL_1: - case WCD938X_MICB2_TEST_CTL_2: - case WCD938X_MICB2_TEST_CTL_3: - case WCD938X_MICB3_TEST_CTL_1: - case WCD938X_MICB3_TEST_CTL_2: - case WCD938X_MICB3_TEST_CTL_3: - case WCD938X_MICB4_TEST_CTL_1: - case WCD938X_MICB4_TEST_CTL_2: - case WCD938X_MICB4_TEST_CTL_3: - case WCD938X_TX_COM_ADC_VCM: - case WCD938X_TX_COM_BIAS_ATEST: - case WCD938X_TX_COM_SPARE1: - case WCD938X_TX_COM_SPARE2: - case WCD938X_TX_COM_TXFE_DIV_CTL: - case WCD938X_TX_COM_TXFE_DIV_START: - case WCD938X_TX_COM_SPARE3: - case WCD938X_TX_COM_SPARE4: - case WCD938X_TX_1_2_TEST_EN: - case WCD938X_TX_1_2_ADC_IB: - case WCD938X_TX_1_2_ATEST_REFCTL: - case WCD938X_TX_1_2_TEST_CTL: - case WCD938X_TX_1_2_TEST_BLK_EN1: - case WCD938X_TX_1_2_TXFE1_CLKDIV: - case WCD938X_TX_3_4_TEST_EN: - case WCD938X_TX_3_4_ADC_IB: - case WCD938X_TX_3_4_ATEST_REFCTL: - case WCD938X_TX_3_4_TEST_CTL: - case WCD938X_TX_3_4_TEST_BLK_EN3: - case WCD938X_TX_3_4_TXFE3_CLKDIV: - case WCD938X_TX_3_4_TEST_BLK_EN2: - case WCD938X_TX_3_4_TXFE2_CLKDIV: - case WCD938X_TX_3_4_SPARE1: - case WCD938X_TX_3_4_TEST_BLK_EN4: - case WCD938X_TX_3_4_TXFE4_CLKDIV: - case WCD938X_TX_3_4_SPARE2: - case WCD938X_CLASSH_MODE_1: - case WCD938X_CLASSH_MODE_2: - case WCD938X_CLASSH_MODE_3: - case WCD938X_CLASSH_CTRL_VCL_1: - case WCD938X_CLASSH_CTRL_VCL_2: - case WCD938X_CLASSH_CTRL_CCL_1: - case WCD938X_CLASSH_CTRL_CCL_2: - case WCD938X_CLASSH_CTRL_CCL_3: - case WCD938X_CLASSH_CTRL_CCL_4: - case WCD938X_CLASSH_CTRL_CCL_5: - case WCD938X_CLASSH_BUCK_TMUX_A_D: - case WCD938X_CLASSH_BUCK_SW_DRV_CNTL: - case WCD938X_CLASSH_SPARE: - case WCD938X_FLYBACK_EN: - case WCD938X_FLYBACK_VNEG_CTRL_1: - case WCD938X_FLYBACK_VNEG_CTRL_2: - case WCD938X_FLYBACK_VNEG_CTRL_3: - case WCD938X_FLYBACK_VNEG_CTRL_4: - case WCD938X_FLYBACK_VNEG_CTRL_5: - case WCD938X_FLYBACK_VNEG_CTRL_6: - case WCD938X_FLYBACK_VNEG_CTRL_7: - case WCD938X_FLYBACK_VNEG_CTRL_8: - case WCD938X_FLYBACK_VNEG_CTRL_9: - case WCD938X_FLYBACK_VNEGDAC_CTRL_1: - case WCD938X_FLYBACK_VNEGDAC_CTRL_2: - case WCD938X_FLYBACK_VNEGDAC_CTRL_3: - case WCD938X_FLYBACK_CTRL_1: - case WCD938X_FLYBACK_TEST_CTL: - case WCD938X_RX_AUX_SW_CTL: - case WCD938X_RX_PA_AUX_IN_CONN: - case WCD938X_RX_TIMER_DIV: - case WCD938X_RX_OCP_CTL: - case WCD938X_RX_OCP_COUNT: - case WCD938X_RX_BIAS_EAR_DAC: - case WCD938X_RX_BIAS_EAR_AMP: - case WCD938X_RX_BIAS_HPH_LDO: - case WCD938X_RX_BIAS_HPH_PA: - case WCD938X_RX_BIAS_HPH_RDACBUFF_CNP2: - case WCD938X_RX_BIAS_HPH_RDAC_LDO: - case WCD938X_RX_BIAS_HPH_CNP1: - case WCD938X_RX_BIAS_HPH_LOWPOWER: - case WCD938X_RX_BIAS_AUX_DAC: - case WCD938X_RX_BIAS_AUX_AMP: - case WCD938X_RX_BIAS_VNEGDAC_BLEEDER: - case WCD938X_RX_BIAS_MISC: - case WCD938X_RX_BIAS_BUCK_RST: - case WCD938X_RX_BIAS_BUCK_VREF_ERRAMP: - case WCD938X_RX_BIAS_FLYB_ERRAMP: - case WCD938X_RX_BIAS_FLYB_BUFF: - case WCD938X_RX_BIAS_FLYB_MID_RST: - case WCD938X_HPH_CNP_EN: - case WCD938X_HPH_CNP_WG_CTL: - case WCD938X_HPH_CNP_WG_TIME: - case WCD938X_HPH_OCP_CTL: - case WCD938X_HPH_AUTO_CHOP: - case WCD938X_HPH_CHOP_CTL: - case WCD938X_HPH_PA_CTL1: - case WCD938X_HPH_PA_CTL2: - case WCD938X_HPH_L_EN: - case WCD938X_HPH_L_TEST: - case WCD938X_HPH_L_ATEST: - case WCD938X_HPH_R_EN: - case WCD938X_HPH_R_TEST: - case WCD938X_HPH_R_ATEST: - case WCD938X_HPH_RDAC_CLK_CTL1: - case WCD938X_HPH_RDAC_CLK_CTL2: - case WCD938X_HPH_RDAC_LDO_CTL: - case WCD938X_HPH_RDAC_CHOP_CLK_LP_CTL: - case WCD938X_HPH_REFBUFF_UHQA_CTL: - case WCD938X_HPH_REFBUFF_LP_CTL: - case WCD938X_HPH_L_DAC_CTL: - case WCD938X_HPH_R_DAC_CTL: - case WCD938X_HPH_SURGE_HPHLR_SURGE_COMP_SEL: - case WCD938X_HPH_SURGE_HPHLR_SURGE_EN: - case WCD938X_HPH_SURGE_HPHLR_SURGE_MISC1: - case WCD938X_EAR_EAR_EN_REG: - case WCD938X_EAR_EAR_PA_CON: - case WCD938X_EAR_EAR_SP_CON: - case WCD938X_EAR_EAR_DAC_CON: - case WCD938X_EAR_EAR_CNP_FSM_CON: - case WCD938X_EAR_TEST_CTL: - case WCD938X_ANA_NEW_PAGE_REGISTER: - case WCD938X_HPH_NEW_ANA_HPH2: - case WCD938X_HPH_NEW_ANA_HPH3: - case WCD938X_SLEEP_CTL: - case WCD938X_SLEEP_WATCHDOG_CTL: - case WCD938X_MBHC_NEW_ELECT_REM_CLAMP_CTL: - case WCD938X_MBHC_NEW_CTL_1: - case WCD938X_MBHC_NEW_CTL_2: - case WCD938X_MBHC_NEW_PLUG_DETECT_CTL: - case WCD938X_MBHC_NEW_ZDET_ANA_CTL: - case WCD938X_MBHC_NEW_ZDET_RAMP_CTL: - case WCD938X_TX_NEW_AMIC_MUX_CFG: - case WCD938X_AUX_AUXPA: - case WCD938X_LDORXTX_MODE: - case WCD938X_LDORXTX_CONFIG: - case WCD938X_DIE_CRACK_DIE_CRK_DET_EN: - case WCD938X_HPH_NEW_INT_RDAC_GAIN_CTL: - case WCD938X_HPH_NEW_INT_RDAC_HD2_CTL_L: - case WCD938X_HPH_NEW_INT_RDAC_VREF_CTL: - case WCD938X_HPH_NEW_INT_RDAC_OVERRIDE_CTL: - case WCD938X_HPH_NEW_INT_RDAC_HD2_CTL_R: - case WCD938X_HPH_NEW_INT_PA_MISC1: - case WCD938X_HPH_NEW_INT_PA_MISC2: - case WCD938X_HPH_NEW_INT_PA_RDAC_MISC: - case WCD938X_HPH_NEW_INT_HPH_TIMER1: - case WCD938X_HPH_NEW_INT_HPH_TIMER2: - case WCD938X_HPH_NEW_INT_HPH_TIMER3: - case WCD938X_HPH_NEW_INT_HPH_TIMER4: - case WCD938X_HPH_NEW_INT_PA_RDAC_MISC2: - case WCD938X_HPH_NEW_INT_PA_RDAC_MISC3: - case WCD938X_HPH_NEW_INT_RDAC_HD2_CTL_L_NEW: - case WCD938X_HPH_NEW_INT_RDAC_HD2_CTL_R_NEW: - case WCD938X_RX_NEW_INT_HPH_RDAC_BIAS_LOHIFI: - case WCD938X_RX_NEW_INT_HPH_RDAC_BIAS_ULP: - case WCD938X_RX_NEW_INT_HPH_RDAC_LDO_LP: - case WCD938X_MBHC_NEW_INT_MOISTURE_DET_DC_CTRL: - case WCD938X_MBHC_NEW_INT_MOISTURE_DET_POLLING_CTRL: - case WCD938X_MBHC_NEW_INT_MECH_DET_CURRENT: - case WCD938X_MBHC_NEW_INT_SPARE_2: - case WCD938X_EAR_INT_NEW_EAR_CHOPPER_CON: - case WCD938X_EAR_INT_NEW_CNP_VCM_CON1: - case WCD938X_EAR_INT_NEW_CNP_VCM_CON2: - case WCD938X_EAR_INT_NEW_EAR_DYNAMIC_BIAS: - case WCD938X_AUX_INT_EN_REG: - case WCD938X_AUX_INT_PA_CTRL: - case WCD938X_AUX_INT_SP_CTRL: - case WCD938X_AUX_INT_DAC_CTRL: - case WCD938X_AUX_INT_CLK_CTRL: - case WCD938X_AUX_INT_TEST_CTRL: - case WCD938X_AUX_INT_MISC: - case WCD938X_LDORXTX_INT_BIAS: - case WCD938X_LDORXTX_INT_STB_LOADS_DTEST: - case WCD938X_LDORXTX_INT_TEST0: - case WCD938X_LDORXTX_INT_STARTUP_TIMER: - case WCD938X_LDORXTX_INT_TEST1: - case WCD938X_SLEEP_INT_WATCHDOG_CTL_1: - case WCD938X_SLEEP_INT_WATCHDOG_CTL_2: - case WCD938X_DIE_CRACK_INT_DIE_CRK_DET_INT1: - case WCD938X_DIE_CRACK_INT_DIE_CRK_DET_INT2: - case WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_L2: - case WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_L1: - case WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_L0: - case WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_ULP1P2M: - case WCD938X_TX_COM_NEW_INT_TXFE_DIVSTOP_ULP0P6M: - case WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG1_L2L1: - case WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG1_L0: - case WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG1_ULP: - case WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2MAIN_L2L1: - case WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2MAIN_L0: - case WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2MAIN_ULP: - case WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2CASC_L2L1L0: - case WCD938X_TX_COM_NEW_INT_TXFE_ICTRL_STG2CASC_ULP: - case WCD938X_TX_COM_NEW_INT_TXADC_SCBIAS_L2L1: - case WCD938X_TX_COM_NEW_INT_TXADC_SCBIAS_L0ULP: - case WCD938X_TX_COM_NEW_INT_TXADC_INT_L2: - case WCD938X_TX_COM_NEW_INT_TXADC_INT_L1: - case WCD938X_TX_COM_NEW_INT_TXADC_INT_L0: - case WCD938X_TX_COM_NEW_INT_TXADC_INT_ULP: - case WCD938X_DIGITAL_PAGE_REGISTER: - case WCD938X_DIGITAL_SWR_TX_CLK_RATE: - case WCD938X_DIGITAL_CDC_RST_CTL: - case WCD938X_DIGITAL_TOP_CLK_CFG: - case WCD938X_DIGITAL_CDC_ANA_CLK_CTL: - case WCD938X_DIGITAL_CDC_DIG_CLK_CTL: - case WCD938X_DIGITAL_SWR_RST_EN: - case WCD938X_DIGITAL_CDC_PATH_MODE: - case WCD938X_DIGITAL_CDC_RX_RST: - case WCD938X_DIGITAL_CDC_RX0_CTL: - case WCD938X_DIGITAL_CDC_RX1_CTL: - case WCD938X_DIGITAL_CDC_RX2_CTL: - case WCD938X_DIGITAL_CDC_TX_ANA_MODE_0_1: - case WCD938X_DIGITAL_CDC_TX_ANA_MODE_2_3: - case WCD938X_DIGITAL_CDC_COMP_CTL_0: - case WCD938X_DIGITAL_CDC_ANA_TX_CLK_CTL: - case WCD938X_DIGITAL_CDC_HPH_DSM_A1_0: - case WCD938X_DIGITAL_CDC_HPH_DSM_A1_1: - case WCD938X_DIGITAL_CDC_HPH_DSM_A2_0: - case WCD938X_DIGITAL_CDC_HPH_DSM_A2_1: - case WCD938X_DIGITAL_CDC_HPH_DSM_A3_0: - case WCD938X_DIGITAL_CDC_HPH_DSM_A3_1: - case WCD938X_DIGITAL_CDC_HPH_DSM_A4_0: - case WCD938X_DIGITAL_CDC_HPH_DSM_A4_1: - case WCD938X_DIGITAL_CDC_HPH_DSM_A5_0: - case WCD938X_DIGITAL_CDC_HPH_DSM_A5_1: - case WCD938X_DIGITAL_CDC_HPH_DSM_A6_0: - case WCD938X_DIGITAL_CDC_HPH_DSM_A7_0: - case WCD938X_DIGITAL_CDC_HPH_DSM_C_0: - case WCD938X_DIGITAL_CDC_HPH_DSM_C_1: - case WCD938X_DIGITAL_CDC_HPH_DSM_C_2: - case WCD938X_DIGITAL_CDC_HPH_DSM_C_3: - case WCD938X_DIGITAL_CDC_HPH_DSM_R1: - case WCD938X_DIGITAL_CDC_HPH_DSM_R2: - case WCD938X_DIGITAL_CDC_HPH_DSM_R3: - case WCD938X_DIGITAL_CDC_HPH_DSM_R4: - case WCD938X_DIGITAL_CDC_HPH_DSM_R5: - case WCD938X_DIGITAL_CDC_HPH_DSM_R6: - case WCD938X_DIGITAL_CDC_HPH_DSM_R7: - case WCD938X_DIGITAL_CDC_AUX_DSM_A1_0: - case WCD938X_DIGITAL_CDC_AUX_DSM_A1_1: - case WCD938X_DIGITAL_CDC_AUX_DSM_A2_0: - case WCD938X_DIGITAL_CDC_AUX_DSM_A2_1: - case WCD938X_DIGITAL_CDC_AUX_DSM_A3_0: - case WCD938X_DIGITAL_CDC_AUX_DSM_A3_1: - case WCD938X_DIGITAL_CDC_AUX_DSM_A4_0: - case WCD938X_DIGITAL_CDC_AUX_DSM_A4_1: - case WCD938X_DIGITAL_CDC_AUX_DSM_A5_0: - case WCD938X_DIGITAL_CDC_AUX_DSM_A5_1: - case WCD938X_DIGITAL_CDC_AUX_DSM_A6_0: - case WCD938X_DIGITAL_CDC_AUX_DSM_A7_0: - case WCD938X_DIGITAL_CDC_AUX_DSM_C_0: - case WCD938X_DIGITAL_CDC_AUX_DSM_C_1: - case WCD938X_DIGITAL_CDC_AUX_DSM_C_2: - case WCD938X_DIGITAL_CDC_AUX_DSM_C_3: - case WCD938X_DIGITAL_CDC_AUX_DSM_R1: - case WCD938X_DIGITAL_CDC_AUX_DSM_R2: - case WCD938X_DIGITAL_CDC_AUX_DSM_R3: - case WCD938X_DIGITAL_CDC_AUX_DSM_R4: - case WCD938X_DIGITAL_CDC_AUX_DSM_R5: - case WCD938X_DIGITAL_CDC_AUX_DSM_R6: - case WCD938X_DIGITAL_CDC_AUX_DSM_R7: - case WCD938X_DIGITAL_CDC_HPH_GAIN_RX_0: - case WCD938X_DIGITAL_CDC_HPH_GAIN_RX_1: - case WCD938X_DIGITAL_CDC_HPH_GAIN_DSD_0: - case WCD938X_DIGITAL_CDC_HPH_GAIN_DSD_1: - case WCD938X_DIGITAL_CDC_HPH_GAIN_DSD_2: - case WCD938X_DIGITAL_CDC_AUX_GAIN_DSD_0: - case WCD938X_DIGITAL_CDC_AUX_GAIN_DSD_1: - case WCD938X_DIGITAL_CDC_AUX_GAIN_DSD_2: - case WCD938X_DIGITAL_CDC_HPH_GAIN_CTL: - case WCD938X_DIGITAL_CDC_AUX_GAIN_CTL: - case WCD938X_DIGITAL_CDC_EAR_PATH_CTL: - case WCD938X_DIGITAL_CDC_SWR_CLH: - case WCD938X_DIGITAL_SWR_CLH_BYP: - case WCD938X_DIGITAL_CDC_TX0_CTL: - case WCD938X_DIGITAL_CDC_TX1_CTL: - case WCD938X_DIGITAL_CDC_TX2_CTL: - case WCD938X_DIGITAL_CDC_TX_RST: - case WCD938X_DIGITAL_CDC_REQ_CTL: - case WCD938X_DIGITAL_CDC_RST: - case WCD938X_DIGITAL_CDC_AMIC_CTL: - case WCD938X_DIGITAL_CDC_DMIC_CTL: - case WCD938X_DIGITAL_CDC_DMIC1_CTL: - case WCD938X_DIGITAL_CDC_DMIC2_CTL: - case WCD938X_DIGITAL_CDC_DMIC3_CTL: - case WCD938X_DIGITAL_CDC_DMIC4_CTL: - case WCD938X_DIGITAL_EFUSE_PRG_CTL: - case WCD938X_DIGITAL_EFUSE_CTL: - case WCD938X_DIGITAL_CDC_DMIC_RATE_1_2: - case WCD938X_DIGITAL_CDC_DMIC_RATE_3_4: - case WCD938X_DIGITAL_PDM_WD_CTL0: - case WCD938X_DIGITAL_PDM_WD_CTL1: - case WCD938X_DIGITAL_PDM_WD_CTL2: - case WCD938X_DIGITAL_INTR_MODE: - case WCD938X_DIGITAL_INTR_MASK_0: - case WCD938X_DIGITAL_INTR_MASK_1: - case WCD938X_DIGITAL_INTR_MASK_2: - case WCD938X_DIGITAL_INTR_CLEAR_0: - case WCD938X_DIGITAL_INTR_CLEAR_1: - case WCD938X_DIGITAL_INTR_CLEAR_2: - case WCD938X_DIGITAL_INTR_LEVEL_0: - case WCD938X_DIGITAL_INTR_LEVEL_1: - case WCD938X_DIGITAL_INTR_LEVEL_2: - case WCD938X_DIGITAL_INTR_SET_0: - case WCD938X_DIGITAL_INTR_SET_1: - case WCD938X_DIGITAL_INTR_SET_2: - case WCD938X_DIGITAL_INTR_TEST_0: - case WCD938X_DIGITAL_INTR_TEST_1: - case WCD938X_DIGITAL_INTR_TEST_2: - case WCD938X_DIGITAL_TX_MODE_DBG_EN: - case WCD938X_DIGITAL_TX_MODE_DBG_0_1: - case WCD938X_DIGITAL_TX_MODE_DBG_2_3: - case WCD938X_DIGITAL_LB_IN_SEL_CTL: - case WCD938X_DIGITAL_LOOP_BACK_MODE: - case WCD938X_DIGITAL_SWR_DAC_TEST: - case WCD938X_DIGITAL_SWR_HM_TEST_RX_0: - case WCD938X_DIGITAL_SWR_HM_TEST_TX_0: - case WCD938X_DIGITAL_SWR_HM_TEST_RX_1: - case WCD938X_DIGITAL_SWR_HM_TEST_TX_1: - case WCD938X_DIGITAL_SWR_HM_TEST_TX_2: - case WCD938X_DIGITAL_PAD_CTL_SWR_0: - case WCD938X_DIGITAL_PAD_CTL_SWR_1: - case WCD938X_DIGITAL_I2C_CTL: - case WCD938X_DIGITAL_CDC_TX_TANGGU_SW_MODE: - case WCD938X_DIGITAL_EFUSE_TEST_CTL_0: - case WCD938X_DIGITAL_EFUSE_TEST_CTL_1: - case WCD938X_DIGITAL_PAD_CTL_PDM_RX0: - case WCD938X_DIGITAL_PAD_CTL_PDM_RX1: - case WCD938X_DIGITAL_PAD_CTL_PDM_TX0: - case WCD938X_DIGITAL_PAD_CTL_PDM_TX1: - case WCD938X_DIGITAL_PAD_CTL_PDM_TX2: - case WCD938X_DIGITAL_PAD_INP_DIS_0: - case WCD938X_DIGITAL_PAD_INP_DIS_1: - case WCD938X_DIGITAL_DRIVE_STRENGTH_0: - case WCD938X_DIGITAL_DRIVE_STRENGTH_1: - case WCD938X_DIGITAL_DRIVE_STRENGTH_2: - case WCD938X_DIGITAL_RX_DATA_EDGE_CTL: - case WCD938X_DIGITAL_TX_DATA_EDGE_CTL: - case WCD938X_DIGITAL_GPIO_MODE: - case WCD938X_DIGITAL_PIN_CTL_OE: - case WCD938X_DIGITAL_PIN_CTL_DATA_0: - case WCD938X_DIGITAL_PIN_CTL_DATA_1: - case WCD938X_DIGITAL_DIG_DEBUG_CTL: - case WCD938X_DIGITAL_DIG_DEBUG_EN: - case WCD938X_DIGITAL_ANA_CSR_DBG_ADD: - case WCD938X_DIGITAL_ANA_CSR_DBG_CTL: - case WCD938X_DIGITAL_SSP_DBG: - case WCD938X_DIGITAL_SPARE_0: - case WCD938X_DIGITAL_SPARE_1: - case WCD938X_DIGITAL_SPARE_2: - case WCD938X_DIGITAL_TX_REQ_FB_CTL_0: - case WCD938X_DIGITAL_TX_REQ_FB_CTL_1: - case WCD938X_DIGITAL_TX_REQ_FB_CTL_2: - case WCD938X_DIGITAL_TX_REQ_FB_CTL_3: - case WCD938X_DIGITAL_TX_REQ_FB_CTL_4: - case WCD938X_DIGITAL_DEM_BYPASS_DATA0: - case WCD938X_DIGITAL_DEM_BYPASS_DATA1: - case WCD938X_DIGITAL_DEM_BYPASS_DATA2: - case WCD938X_DIGITAL_DEM_BYPASS_DATA3: - return true; - } - - return false; -} - -static bool wcd938x_readonly_register(struct device *dev, unsigned int reg) -{ - switch (reg) { - case WCD938X_ANA_MBHC_RESULT_1: - case WCD938X_ANA_MBHC_RESULT_2: - case WCD938X_ANA_MBHC_RESULT_3: - case WCD938X_MBHC_MOISTURE_DET_FSM_STATUS: - case WCD938X_TX_1_2_SAR2_ERR: - case WCD938X_TX_1_2_SAR1_ERR: - case WCD938X_TX_3_4_SAR4_ERR: - case WCD938X_TX_3_4_SAR3_ERR: - case WCD938X_HPH_L_STATUS: - case WCD938X_HPH_R_STATUS: - case WCD938X_HPH_SURGE_HPHLR_SURGE_STATUS: - case WCD938X_EAR_STATUS_REG_1: - case WCD938X_EAR_STATUS_REG_2: - case WCD938X_MBHC_NEW_FSM_STATUS: - case WCD938X_MBHC_NEW_ADC_RESULT: - case WCD938X_DIE_CRACK_DIE_CRK_DET_OUT: - case WCD938X_AUX_INT_STATUS_REG: - case WCD938X_LDORXTX_INT_STATUS: - case WCD938X_DIGITAL_CHIP_ID0: - case WCD938X_DIGITAL_CHIP_ID1: - case WCD938X_DIGITAL_CHIP_ID2: - case WCD938X_DIGITAL_CHIP_ID3: - case WCD938X_DIGITAL_INTR_STATUS_0: - case WCD938X_DIGITAL_INTR_STATUS_1: - case WCD938X_DIGITAL_INTR_STATUS_2: - case WCD938X_DIGITAL_INTR_CLEAR_0: - case WCD938X_DIGITAL_INTR_CLEAR_1: - case WCD938X_DIGITAL_INTR_CLEAR_2: - case WCD938X_DIGITAL_SWR_HM_TEST_0: - case WCD938X_DIGITAL_SWR_HM_TEST_1: - case WCD938X_DIGITAL_EFUSE_T_DATA_0: - case WCD938X_DIGITAL_EFUSE_T_DATA_1: - case WCD938X_DIGITAL_PIN_STATUS_0: - case WCD938X_DIGITAL_PIN_STATUS_1: - case WCD938X_DIGITAL_MODE_STATUS_0: - case WCD938X_DIGITAL_MODE_STATUS_1: - case WCD938X_DIGITAL_EFUSE_REG_0: - case WCD938X_DIGITAL_EFUSE_REG_1: - case WCD938X_DIGITAL_EFUSE_REG_2: - case WCD938X_DIGITAL_EFUSE_REG_3: - case WCD938X_DIGITAL_EFUSE_REG_4: - case WCD938X_DIGITAL_EFUSE_REG_5: - case WCD938X_DIGITAL_EFUSE_REG_6: - case WCD938X_DIGITAL_EFUSE_REG_7: - case WCD938X_DIGITAL_EFUSE_REG_8: - case WCD938X_DIGITAL_EFUSE_REG_9: - case WCD938X_DIGITAL_EFUSE_REG_10: - case WCD938X_DIGITAL_EFUSE_REG_11: - case WCD938X_DIGITAL_EFUSE_REG_12: - case WCD938X_DIGITAL_EFUSE_REG_13: - case WCD938X_DIGITAL_EFUSE_REG_14: - case WCD938X_DIGITAL_EFUSE_REG_15: - case WCD938X_DIGITAL_EFUSE_REG_16: - case WCD938X_DIGITAL_EFUSE_REG_17: - case WCD938X_DIGITAL_EFUSE_REG_18: - case WCD938X_DIGITAL_EFUSE_REG_19: - case WCD938X_DIGITAL_EFUSE_REG_20: - case WCD938X_DIGITAL_EFUSE_REG_21: - case WCD938X_DIGITAL_EFUSE_REG_22: - case WCD938X_DIGITAL_EFUSE_REG_23: - case WCD938X_DIGITAL_EFUSE_REG_24: - case WCD938X_DIGITAL_EFUSE_REG_25: - case WCD938X_DIGITAL_EFUSE_REG_26: - case WCD938X_DIGITAL_EFUSE_REG_27: - case WCD938X_DIGITAL_EFUSE_REG_28: - case WCD938X_DIGITAL_EFUSE_REG_29: - case WCD938X_DIGITAL_EFUSE_REG_30: - case WCD938X_DIGITAL_EFUSE_REG_31: - return true; - } - return false; -} - -static bool wcd938x_readable_register(struct device *dev, unsigned int reg) -{ - bool ret; - - ret = wcd938x_readonly_register(dev, reg); - if (!ret) - return wcd938x_rdwr_register(dev, reg); - - return ret; -} - -static bool wcd938x_writeable_register(struct device *dev, unsigned int reg) -{ - return wcd938x_rdwr_register(dev, reg); -} - -static bool wcd938x_volatile_register(struct device *dev, unsigned int reg) -{ - if (reg <= WCD938X_BASE_ADDRESS) - return false; - - if (reg == WCD938X_DIGITAL_SWR_TX_CLK_RATE) - return true; - - if (wcd938x_readonly_register(dev, reg)) - return true; - - return false; -} - -static struct regmap_config wcd938x_regmap_config = { - .name = "wcd938x_csr", - .reg_bits = 32, - .val_bits = 8, - .cache_type = REGCACHE_RBTREE, - .reg_defaults = wcd938x_defaults, - .num_reg_defaults = ARRAY_SIZE(wcd938x_defaults), - .max_register = WCD938X_MAX_REGISTER, - .readable_reg = wcd938x_readable_register, - .writeable_reg = wcd938x_writeable_register, - .volatile_reg = wcd938x_volatile_register, - .can_multi_write = true, -}; - static const struct regmap_irq wcd938x_irqs[WCD938X_NUM_IRQS] = { REGMAP_IRQ_REG(WCD938X_IRQ_MBHC_BUTTON_PRESS_DET, 0, 0x01), REGMAP_IRQ_REG(WCD938X_IRQ_MBHC_BUTTON_RELEASE_DET, 0, 0x02), @@ -4405,10 +3410,10 @@ static int wcd938x_bind(struct device *dev) return -EINVAL; } - wcd938x->regmap = devm_regmap_init_sdw(wcd938x->tx_sdw_dev, &wcd938x_regmap_config); - if (IS_ERR(wcd938x->regmap)) { - dev_err(dev, "%s: tx csr regmap not found\n", __func__); - return PTR_ERR(wcd938x->regmap); + wcd938x->regmap = dev_get_regmap(&wcd938x->tx_sdw_dev->dev, NULL); + if (!wcd938x->regmap) { + dev_err(dev, "could not get TX device regmap\n"); + return -EINVAL; } ret = wcd938x_irq_init(wcd938x, dev); diff --git a/sound/soc/codecs/wcd938x.h b/sound/soc/codecs/wcd938x.h index ea82039e7843..74b1498fec38 100644 --- a/sound/soc/codecs/wcd938x.h +++ b/sound/soc/codecs/wcd938x.h @@ -663,6 +663,7 @@ struct wcd938x_sdw_priv { bool is_tx; struct wcd938x_priv *wcd938x; struct irq_domain *slave_irq; + struct regmap *regmap; }; #if IS_ENABLED(CONFIG_SND_SOC_WCD938X_SDW) -- 2.34.1

4 3

[PATCH] ASoC: Intel: soc-acpi-cht: Add quirk for Nextbook Ares 8A tablet
by Hans de Goede 04 May '23

04 May '23

The Nextbook Ares 8A tablet which has Android as factory OS, has a buggy DSDT with both ESSX8316 and 10EC5651 ACPI devices. This tablet actually uses an rt5651 codec, but the matching code ends up picking the ESSX8316 device, add a quirk to ignote the ESSX8316 device on this tablet. Signed-off-by: Hans de Goede <hdegoede(a)redhat.com> --- .../intel/common/soc-acpi-intel-cht-match.c | 26 +++++++++++++++++++ 1 file changed, 26 insertions(+) diff --git a/sound/soc/intel/common/soc-acpi-intel-cht-match.c b/sound/soc/intel/common/soc-acpi-intel-cht-match.c index 6beb00858c33..cdcbf04b8832 100644 --- a/sound/soc/intel/common/soc-acpi-intel-cht-match.c +++ b/sound/soc/intel/common/soc-acpi-intel-cht-match.c @@ -50,6 +50,31 @@ static struct snd_soc_acpi_mach *cht_quirk(void *arg) return mach; } +/* + * Some tablets with Android factory OS have buggy DSDTs with an ESSX8316 device + * in the ACPI tables. While they are not using an ESS8316 codec. These DSDTs + * also have an ACPI device for the correct codec, ignore the ESSX8316. + */ +static const struct dmi_system_id cht_ess8316_not_present_table[] = { + { + /* Nextbook Ares 8A */ + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Insyde"), + DMI_MATCH(DMI_PRODUCT_NAME, "CherryTrail"), + DMI_MATCH(DMI_BIOS_VERSION, "M882"), + }, + }, + { } +}; + +static struct snd_soc_acpi_mach *cht_ess8316_quirk(void *arg) +{ + if (dmi_check_system(cht_ess8316_not_present_table)) + return NULL; + + return arg; +} + static const struct snd_soc_acpi_codecs rt5640_comp_ids = { .num_codecs = 2, .codecs = { "10EC5640", "10EC3276" }, @@ -113,6 +138,7 @@ struct snd_soc_acpi_mach snd_soc_acpi_intel_cherrytrail_machines[] = { .drv_name = "bytcht_es8316", .fw_filename = "intel/fw_sst_22a8.bin", .board = "bytcht_es8316", + .machine_quirk = cht_ess8316_quirk, .sof_tplg_filename = "sof-cht-es8316.tplg", }, /* some CHT-T platforms rely on RT5640, use Baytrail machine driver */ -- 2.39.2

4 3

[PATCH] ASoC: amd: yc: Add Asus VivoBook Pro 14 OLED M6400RC to the quirks list for acp6x
by Andrey Rakhmatullin 04 May '23

04 May '23

This is needed (and enough) to get the internal mic visible and working. Signed-off-by: Andrey Rakhmatullin <wrar(a)wrar.name> --- sound/soc/amd/yc/acp6x-mach.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/sound/soc/amd/yc/acp6x-mach.c b/sound/soc/amd/yc/acp6x-mach.c index b9958e555367..0208cb0ae978 100644 --- a/sound/soc/amd/yc/acp6x-mach.c +++ b/sound/soc/amd/yc/acp6x-mach.c @@ -227,6 +227,13 @@ static const struct dmi_system_id yc_acp_quirk_table[] = { DMI_MATCH(DMI_PRODUCT_NAME, "M5402RA"), } }, + { + .driver_data = &acp6x_card, + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, "ASUSTeK COMPUTER INC."), + DMI_MATCH(DMI_PRODUCT_NAME, "M6400RC"), + } + }, { .driver_data = &acp6x_card, .matches = { -- 2.39.2

3 2

[PATCH] pcm: remove duplicate SND_PCM_HW_PARAM_{FIRST,LAST}_* #defines
by Oswald Buddenhagen 03 May '23

03 May '23

Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- one might also want to re-arrange the remaining items. --- src/pcm/pcm_local.h | 4 ---- 1 file changed, 4 deletions(-) diff --git a/src/pcm/pcm_local.h b/src/pcm/pcm_local.h index abea6654..6a0e71e7 100644 --- a/src/pcm/pcm_local.h +++ b/src/pcm/pcm_local.h @@ -48,24 +48,20 @@ #include "mask.h" #define SND_PCM_HW_PARAM_ACCESS SNDRV_PCM_HW_PARAM_ACCESS -#define SND_PCM_HW_PARAM_FIRST_MASK SNDRV_PCM_HW_PARAM_FIRST_MASK #define SND_PCM_HW_PARAM_FORMAT SNDRV_PCM_HW_PARAM_FORMAT #define SND_PCM_HW_PARAM_SUBFORMAT SNDRV_PCM_HW_PARAM_SUBFORMAT -#define SND_PCM_HW_PARAM_LAST_MASK SNDRV_PCM_HW_PARAM_LAST_MASK #define SND_PCM_HW_PARAM_SAMPLE_BITS SNDRV_PCM_HW_PARAM_SAMPLE_BITS -#define SND_PCM_HW_PARAM_FIRST_INTERVAL SNDRV_PCM_HW_PARAM_FIRST_INTERVAL #define SND_PCM_HW_PARAM_FRAME_BITS SNDRV_PCM_HW_PARAM_FRAME_BITS #define SND_PCM_HW_PARAM_CHANNELS SNDRV_PCM_HW_PARAM_CHANNELS #define SND_PCM_HW_PARAM_RATE SNDRV_PCM_HW_PARAM_RATE #define SND_PCM_HW_PARAM_PERIOD_TIME SNDRV_PCM_HW_PARAM_PERIOD_TIME #define SND_PCM_HW_PARAM_PERIOD_SIZE SNDRV_PCM_HW_PARAM_PERIOD_SIZE #define SND_PCM_HW_PARAM_PERIOD_BYTES SNDRV_PCM_HW_PARAM_PERIOD_BYTES #define SND_PCM_HW_PARAM_PERIODS SNDRV_PCM_HW_PARAM_PERIODS #define SND_PCM_HW_PARAM_BUFFER_TIME SNDRV_PCM_HW_PARAM_BUFFER_TIME #define SND_PCM_HW_PARAM_BUFFER_SIZE SNDRV_PCM_HW_PARAM_BUFFER_SIZE #define SND_PCM_HW_PARAM_BUFFER_BYTES SNDRV_PCM_HW_PARAM_BUFFER_BYTES #define SND_PCM_HW_PARAM_TICK_TIME SNDRV_PCM_HW_PARAM_TICK_TIME -#define SND_PCM_HW_PARAM_LAST_INTERVAL SNDRV_PCM_HW_PARAM_LAST_INTERVAL #define SND_PCM_HW_PARAM_LAST_MASK SNDRV_PCM_HW_PARAM_LAST_MASK #define SND_PCM_HW_PARAM_FIRST_MASK SNDRV_PCM_HW_PARAM_FIRST_MASK #define SND_PCM_HW_PARAM_LAST_INTERVAL SNDRV_PCM_HW_PARAM_LAST_INTERVAL -- 2.40.0.152.g15d061e6df

2 1

[PATCH] conf/emu10k1: remove compat with two decades old drivers
by Oswald Buddenhagen 03 May '23

03 May '23

There really isn't much of a point to clutter the files with this. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- src/conf/cards/Audigy.conf | 65 ------------------------------ src/conf/cards/Audigy2.conf | 79 ------------------------------------- src/conf/cards/EMU10K1.conf | 48 ---------------------- 3 files changed, 192 deletions(-) diff --git a/src/conf/cards/Audigy.conf b/src/conf/cards/Audigy.conf index 1c924966..42692cfd 100644 --- a/src/conf/cards/Audigy.conf +++ b/src/conf/cards/Audigy.conf @@ -26,31 +26,14 @@ Audigy.pcm.front.0 { optional true value [ 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Volume" - index { @func private_pcm_subdevice } - lock true - optional true - value [ 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 0 0 ] - } { interface PCM name "EMU10K1 PCM Send Routing" index { @func private_pcm_subdevice } lock true optional true value [ 8 9 0 0 0 0 0 0 8 9 0 0 0 0 0 0 8 9 0 0 0 0 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Routing" - index { @func private_pcm_subdevice } - lock true - optional true - value [ 8 9 0 0 0 0 0 0 8 9 0 0 0 0 0 0 8 9 0 0 0 0 0 0 ] - } - ] } } @@ -79,14 +62,6 @@ Audigy.pcm.rear.0 { optional true value [ 0 0 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Volume" - index { @func private_pcm_subdevice } - lock true - optional true - value [ 0 0 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 ] - } ] } } @@ -115,30 +90,14 @@ Audigy.pcm.center_lfe.0 { optional true value [ 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Volume" - index { @func private_pcm_subdevice } - lock true - optional true - value [ 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 0 0 ] - } { interface PCM name "EMU10K1 PCM Send Routing" index { @func private_pcm_subdevice } lock true optional true value [ 6 7 0 0 0 0 0 0 6 7 0 0 0 0 0 0 6 7 0 0 0 0 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Routing" - index { @func private_pcm_subdevice } - lock true - optional true - value [ 6 7 0 0 0 0 0 0 6 7 0 0 0 0 0 0 6 7 0 0 0 0 0 0 ] - } ] } } @@ -265,14 +224,6 @@ Audigy.pcm.iec958.0 { optional true value [ $AES0 $AES1 $AES2 $AES3 ] } - { - # for compatibility with older drivers - name "IEC958 Playback Default" - lock true - preserve true - optional true - value [ $AES0 $AES1 $AES2 $AES3 ] - } { name "IEC958 Optical Raw Playback Switch" lock true @@ -287,30 +238,14 @@ Audigy.pcm.iec958.0 { optional true value [ 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Volume" - index { @func private_pcm_subdevice } - lock true - optional true - value [ 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 0 0 ] - } { interface PCM name "EMU10K1 PCM Send Routing" index { @func private_pcm_subdevice } lock true optional true value [ 20 21 0 0 0 0 0 0 20 21 0 0 0 0 0 0 20 21 0 0 0 0 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Routing" - index { @func private_pcm_subdevice } - lock true - optional true - value [ 20 21 0 0 0 0 0 0 20 21 0 0 0 0 0 0 20 21 0 0 0 0 0 0 ] - } { name "Audigy Analog/Digital Output Jack" lock true diff --git a/src/conf/cards/Audigy2.conf b/src/conf/cards/Audigy2.conf index cbec7835..35126d23 100644 --- a/src/conf/cards/Audigy2.conf +++ b/src/conf/cards/Audigy2.conf @@ -26,30 +26,14 @@ Audigy2.pcm.front.0 { optional true value [ 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Volume" - index { @func private_pcm_subdevice } - lock true - optional true - value [ 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 0 0 ] - } { interface PCM name "EMU10K1 PCM Send Routing" index { @func private_pcm_subdevice } lock true optional true value [ 8 9 0 0 0 0 0 0 8 9 0 0 0 0 0 0 8 9 0 0 0 0 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Routing" - index { @func private_pcm_subdevice } - lock true - optional true - value [ 8 9 0 0 0 0 0 0 8 9 0 0 0 0 0 0 8 9 0 0 0 0 0 0 ] - } ] } @@ -79,14 +63,6 @@ Audigy2.pcm.rear.0 { optional true value [ 0 0 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Volume" - index { @func private_pcm_subdevice } - lock true - optional true - value [ 0 0 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 ] - } ] } } @@ -115,30 +91,14 @@ Audigy2.pcm.center_lfe.0 { optional true value [ 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Volume" - index { @func private_pcm_subdevice } - lock true - optional true - value [ 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 0 0 ] - } { interface PCM name "EMU10K1 PCM Send Routing" index { @func private_pcm_subdevice } lock true optional true value [ 6 7 0 0 0 0 0 0 6 7 0 0 0 0 0 0 6 7 0 0 0 0 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Routing" - index { @func private_pcm_subdevice } - lock true - optional true - value [ 6 7 0 0 0 0 0 0 6 7 0 0 0 0 0 0 6 7 0 0 0 0 0 0 ] - } ] } } @@ -167,30 +127,14 @@ Audigy2.pcm.side.0 { optional true value [ 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Volume" - index { @func private_pcm_subdevice } - lock true - optional true - value [ 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 0 0 ] - } { interface PCM name "EMU10K1 PCM Send Routing" index { @func private_pcm_subdevice } lock true optional true value [ 14 15 0 0 0 0 0 0 14 15 0 0 0 0 0 0 14 15 0 0 0 0 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Routing" - index { @func private_pcm_subdevice } - lock true - optional true - value [ 14 15 0 0 0 0 0 0 14 15 0 0 0 0 0 0 14 15 0 0 0 0 0 0 ] - } ] } } @@ -374,13 +318,6 @@ Audigy2.pcm.iec958.0 { optional true value [ $AES0 $AES1 $AES2 $AES3 ] } - { - # for compatibility with older drivers - name "IEC958 Playback Default" - preserve true - optional true - value [ $AES0 $AES1 $AES2 $AES3 ] - } { name "IEC958 Optical Raw Playback Switch" lock true @@ -395,30 +332,14 @@ Audigy2.pcm.iec958.0 { optional true value [ 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Volume" - index { @func private_pcm_subdevice } - lock true - optional true - value [ 255 255 0 0 0 0 0 0 255 0 0 0 0 0 0 0 0 255 0 0 0 0 0 0 ] - } { interface PCM name "EMU10K1 PCM Send Routing" index { @func private_pcm_subdevice } lock true optional true value [ 20 21 0 0 0 0 0 0 20 21 0 0 0 0 0 0 20 21 0 0 0 0 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Routing" - index { @func private_pcm_subdevice } - lock true - optional true - value [ 20 21 0 0 0 0 0 0 20 21 0 0 0 0 0 0 20 21 0 0 0 0 0 0 ] - } { name "Audigy Analog/Digital Output Jack" lock true diff --git a/src/conf/cards/EMU10K1.conf b/src/conf/cards/EMU10K1.conf index ef193fe0..430926c7 100644 --- a/src/conf/cards/EMU10K1.conf +++ b/src/conf/cards/EMU10K1.conf @@ -28,30 +28,14 @@ EMU10K1.pcm.front.0 { optional true value [ 255 255 0 0 255 0 0 0 0 255 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Volume" - index { @func private_pcm_subdevice } - # lock true - optional true - value [ 255 255 0 0 255 0 0 0 0 255 0 0 ] - } { interface PCM name "EMU10K1 PCM Send Routing" index { @func private_pcm_subdevice } # lock true optional true value [ 8 9 0 0 8 9 0 0 8 9 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Routing" - index { @func private_pcm_subdevice } - # lock true - optional true - value [ 8 9 0 0 8 9 0 0 8 9 0 0 ] - } ] } } @@ -87,14 +71,6 @@ EMU10K1.pcm.rear.0 { optional true value [ 0 0 255 255 0 0 255 0 0 0 0 255 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Volume" - index { @func private_pcm_subdevice } - # lock true - optional true - value [ 0 0 255 255 0 0 255 0 0 0 0 255 ] - } ] } } @@ -152,30 +128,14 @@ EMU10K1.pcm.center_lfe.0 { optional true value [ 255 255 0 0 255 0 0 0 0 255 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Volume" - index { @func private_pcm_subdevice } - # lock true - optional true - value [ 255 255 0 0 255 0 0 0 0 255 0 0 ] - } { interface PCM name "EMU10K1 PCM Send Routing" index { @func private_pcm_subdevice } # lock true optional true value [ 6 7 0 0 6 7 0 0 6 7 0 0 ] } - { - # for compatibility with older drivers - name "EMU10K1 PCM Send Routing" - index { @func private_pcm_subdevice } - # lock true - optional true - value [ 6 7 0 0 6 7 0 0 6 7 0 0 ] - } ] } } @@ -304,14 +264,6 @@ EMU10K1.pcm.iec958.0 { optional true value [ $AES0 $AES1 $AES2 $AES3 ] } - { - # for compatibility with older drivers - name "IEC958 Playback Default" - lock true - preserve true - optional true - value [ $AES0 $AES1 $AES2 $AES3 ] - } { name "IEC958 Optical Raw Playback Switch" lock true -- 2.40.0.152.g15d061e6df

2 1

ucm2: USB-Audio: Add support for Focusrite Scarlett Solo devices
by GitHub pull_request - opened 03 May '23

03 May '23

alsa-project/alsa-ucm-conf pull request #309 was opened from kepstin: These are basically identical to the Scarlett 2i2 devices of the same generation; the difference is that the first input can only be used for a mic, and the second input can only be used for line/instrument. (On the 2i devices, both inputs are the same - they both have mic preamps, and both support line/instrument input.) I've added a new profile for them so the Comment can be set to the correct device name, but because of the similarity between the Solo and 2i devices, I've re-used the existing Scarlett-2i-HiFi use case to set up the split input devices. Request URL : https://github.com/alsa-project/alsa-ucm-conf/pull/309 Patch URL : https://github.com/alsa-project/alsa-ucm-conf/pull/309.patch Repository URL: https://github.com/alsa-project/alsa-ucm-conf

1 0

arecord: use better time granularity mili/micro/nanoseconds for split file names
by GitHub issues - edited 03 May '23

03 May '23

alsa-project/alsa-utils issue #209 was edited from kfilipan: This is more of a feature request rather than an issue. When using `arecord` with `--max-file-time` and `--use-strftime`, one cannot get nanoseconds in the file name. This is however available in the e.g. `date` command `date +"%Y-%m-%d_%H-%M-%S.%N"` (`%N` gives nanoseconds). This would be useful for testing sound card recording time delays because having only seconds is not precise enough, e.g. it could take days or weeks for even slightly better sound cards to experience a second of delay. Thank you! Issue URL : https://github.com/alsa-project/alsa-utils/issues/209 Repository URL: https://github.com/alsa-project/alsa-utils

1 0

Using mili/micro/nanoseconds in split files
by GitHub issues - opened 03 May '23

03 May '23

alsa-project/alsa-utils issue #209 was opened from kfilipan: This is more of a feature request rather than an issue. When using `arecord` with `--max-file-time` and `--use-strftime`, one cannot get nanoseconds in the file name. This is however available in the e.g. `date` command `date +"%Y-%m-%d_%H-%M-%S.%N"` (`%N` gives nanoseconds). This would be useful for testing sound card recording time delays because having only seconds is not precise enough, e.g. it could take days or weeks for even slightly better sound cards to experience a second of delay. Thank you! Issue URL : https://github.com/alsa-project/alsa-utils/issues/209 Repository URL: https://github.com/alsa-project/alsa-utils

1 0

Using mili/micro/nanoseconds in split files
by GitHub issues - edited 03 May '23

03 May '23

alsa-project/alsa-utils issue #209 was edited from kfilipan: This is more of a feature request rather than an issue. When using `arecord` with `--max-file-time` and `--use-strftime`, one cannot get nanoseconds in the file name. This is however available in the e.g. `date` command `date +"%Y-%m-%d_%H-%M-%S.%N"` (`%N` gives nanoseconds). This would be useful for testing sound card recording time delays because having only seconds is not precise enough, e.g. it could take days or weeks for even slightly better sound cards to experience a second of delay. Thank you! Issue URL : https://github.com/alsa-project/alsa-utils/issues/209 Repository URL: https://github.com/alsa-project/alsa-utils

1 0

[PATCH 0/6] ASoC/soundwire: qcom: correctly probe devices after link init
by Krzysztof Kozlowski 03 May '23

03 May '23

Hi, Dependencies ============ 1. ASoC codec: changes are independent, however they should rather come the same cycle as Soundwire changes, to avoid new warning and small delay. 2. Soundwire: changes (context) depend on: https://lore.kernel.org/r/20230209131336.18252-3-srinivas.kandagatla@linaro… https://lore.kernel.org/all/20230418095447.577001-1-krzysztof.kozlowski@lin… Problems solved =============== Soundwire devices are supposed to be kept in reset state (powered off) till their probe() or component bind() callbacks. However if they are already powered on, then they might enumerate before the master initializes bus in qcom_swrm_init() leading to occasional errors like: qcom-soundwire 6d30000.soundwire-controller: Qualcomm Soundwire controller v2.0.0 Registered wcd938x_codec audio-codec: bound sdw:0:0217:010d:00:4 (ops wcd938x_sdw_component_ops) wcd938x_codec audio-codec: bound sdw:0:0217:010d:00:3 (ops wcd938x_sdw_component_ops) qcom-soundwire 6ad0000.soundwire-controller: swrm_wait_for_wr_fifo_avail err write overflow The problem primarily lies in Qualcomm Soundwire controller probe() sequence: 1. request_threaded_irq() 2. sdw_bus_master_add() - which will cause probe() and component bind() of Soundwire devices, e.g. WCD938x codec drivers. Device drivers might already start accessing their registers. 3. qcom_swrm_init() - which initializes the link/bus and enables interrupts. Any access to device registers at (2) above, will fail because link/bus is not yet initialized. Cc: Patrick Lai <quic_plai(a)quicinc.com> Best regards, Krzysztof Dmitry Torokhov (1): ASoC: wcd938x: switch to using gpiod API Krzysztof Kozlowski (5): ASoC: codecs: wcd938x: Keep device in reset till bind ASoC: codecs: wcd938x: Check for enumeration before using TX device soundwire: qcom: drop unused struct qcom_swrm_ctrl members soudnwire: master: protect concurrecnt check for bus->md soundwire: qcom: do not probe devices before bus/link init drivers/soundwire/master.c | 7 ++- drivers/soundwire/qcom.c | 92 +++++++++++++++++++++++++++++--------- sound/soc/codecs/wcd938x.c | 44 +++++++++++------- 3 files changed, 107 insertions(+), 36 deletions(-) -- 2.34.1

3 26

[Bug 217395] New: Internal Speakers do no work ALC245 HP envy x360 2-in-1 Laptop 13-bf0xxx
by bugzilla-daemon＠kernel.org 03 May '23

03 May '23

https://bugzilla.kernel.org/show_bug.cgi?id=217395 Bug ID: 217395 Summary: Internal Speakers do no work ALC245 HP envy x360 2-in-1 Laptop 13-bf0xxx Product: Platform Specific/Hardware Version: 2.5 Hardware: All OS: Linux Status: NEW Severity: normal Priority: P3 Component: x86-64 Assignee: platform_x86_64(a)kernel-bugs.osdl.org Reporter: sourabhsagar7601(a)gmail.com Regression: No Created attachment 304206 --> https://bugzilla.kernel.org/attachment.cgi?id=304206&action=edit Error logs from dmesg I have tried both Vanilla kernel and distro kernel. Still no sound from speaker Attaching output of a) uname -a, b) inxi -Fxz, c) journalctl -k | grep -Ei "ALSA|HDA|sof[-]|HDMI|snd[_-]|sournd|hda.codec|hda.intel" https://askubuntu.com/questions/1465753/ubuntu-23-04-no-speaker-sound-with-… -- You may reply to this email to add a comment. You are receiving this mail because: You are watching the assignee of the bug.

1 0

[PATCH] ALSA: docs: Fix code block indentation in ALSA driver example
by Bagas Sanjaya 03 May '23

03 May '23

Sphinx reports htmldocs warnings: Documentation/sound/kernel-api/writing-an-alsa-driver.rst:3997: WARNING: Literal block expected; none found. Documentation/sound/kernel-api/writing-an-alsa-driver.rst:4004: WARNING: Literal block expected; none found. Documentation/sound/kernel-api/writing-an-alsa-driver.rst:4009: WARNING: Unexpected indentation. Documentation/sound/kernel-api/writing-an-alsa-driver.rst:4035: WARNING: Literal block expected; none found. These are due to indentation of example driver snippets which is outside the code block scope. Fix these by indenting code blocks in question to the scope. Fixes: 4d421eebe1465d ("ALSA: docs: writing-an-alsa-driver.rst: polishing") Reported-by: kernel test robot <lkp(a)intel.com> Closes: https://lore.kernel.org/linux-doc/202305021822.4U6XOvGf-lkp@intel.com/ Signed-off-by: Bagas Sanjaya <bagasdotme(a)gmail.com> --- .../kernel-api/writing-an-alsa-driver.rst | 22 +++++++++---------- 1 file changed, 11 insertions(+), 11 deletions(-) diff --git a/Documentation/sound/kernel-api/writing-an-alsa-driver.rst b/Documentation/sound/kernel-api/writing-an-alsa-driver.rst index c0f97b5e424969..4335c98b3d828f 100644 --- a/Documentation/sound/kernel-api/writing-an-alsa-driver.rst +++ b/Documentation/sound/kernel-api/writing-an-alsa-driver.rst @@ -3994,21 +3994,21 @@ Driver with A Single Source File Suppose you have a file xyz.c. Add the following two lines:: - snd-xyz-objs := xyz.o - obj-$(CONFIG_SND_XYZ) += snd-xyz.o + snd-xyz-objs := xyz.o + obj-$(CONFIG_SND_XYZ) += snd-xyz.o 2. Create the Kconfig entry Add the new entry of Kconfig for your xyz driver:: - config SND_XYZ - tristate "Foobar XYZ" - depends on SND - select SND_PCM - help - Say Y here to include support for Foobar XYZ soundcard. - To compile this driver as a module, choose M here: - the module will be called snd-xyz. + config SND_XYZ + tristate "Foobar XYZ" + depends on SND + select SND_PCM + help + Say Y here to include support for Foobar XYZ soundcard. + To compile this driver as a module, choose M here: + the module will be called snd-xyz. The line ``select SND_PCM`` specifies that the driver xyz supports PCM. In addition to SND_PCM, the following components are supported for @@ -4032,7 +4032,7 @@ located in the new subdirectory, sound/pci/xyz. 1. Add a new directory (``sound/pci/xyz``) in ``sound/pci/Makefile`` as below:: - obj-$(CONFIG_SND) += sound/pci/xyz/ + obj-$(CONFIG_SND) += sound/pci/xyz/ 2. Under the directory ``sound/pci/xyz``, create a Makefile:: base-commit: 348551ddaf311c76b01cdcbaf61b6fef06a49144 -- An old man doll... just what I always wanted! - Clara

2 1

[PATCH] ALSA: docs: Extend module parameters description
by Ivan Orlov 03 May '23

03 May '23

Common ALSA module parameters look a little bit confusing because of the description lacking, and it took me a while to understand the purpose of their existence. To figure it out I asked the question about them to the "alsa-devel" mailing list, and Takashi Iwai answered me with the text I appended to the ALSA documentation in this patch. These common module parameters aren't used a lot nowadays, but as I understand they are important for providing compatibility with some existing user-space apps. So in my opinion it is a good idea to document why we need them. Signed-off-by: Ivan Orlov <ivan.orlov0322(a)gmail.com> --- Documentation/sound/alsa-configuration.rst | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/Documentation/sound/alsa-configuration.rst b/Documentation/sound/alsa-configuration.rst index af71c68f1e4e..829c672d9fe6 100644 --- a/Documentation/sound/alsa-configuration.rst +++ b/Documentation/sound/alsa-configuration.rst @@ -133,6 +133,19 @@ enable enable card; Default: enabled, for PCI and ISA PnP cards +These options are used for either specifying the order of instances or +controlling enabling and disabling of each one of the devices if there +are multiple devices bound with the same driver. For example, there are +many machines which have two HD-audio controllers (one for HDMI/DP +audio and another for onboard analog). In most cases, the second one is +in primary usage, and people would like to assign it as the first +appearing card. They can do it by specifying "index=1,0" module +parameter, which will swap the assignment slots. + +Today, with the sound backend like PulseAudio and PipeWire which +supports dynamic configuration, it's of little use, but that was a +help for static configuration in the past. + Module snd-adlib ---------------- -- 2.34.1

2 1

Re: linux-6.4 alsa sound broken
by Bagas Sanjaya 03 May '23

03 May '23

On Mon, May 01, 2023 at 11:59:12AM +0800, Jeff Chua wrote: > Latest git pull from Linus's tree ... playing a simple sound file will > resulted in a lot of echo. > > Running on Lenovo X1 with .. > 00:1f.3 Audio device: Intel Corporation Alder Lake PCH-P High > Definition Audio Controller (rev 01) > > I've bisected and reverted the following patch fixed the problem. > > commit 9f656705c5faa18afb26d922cfc64f9fd103c38d Thanks for the regression report. However, where is your dmesg and/or ALSA log when the regression occurs? What is the playback test file? FYI, 9f656705c5faa1 ("ALSA: pcm: rewrite snd_pcm_playback_silence()") is originated as [1/2] of patch series that pokes around the auto-silencer. The other patch ([2/2]) got NAKed since autofilling buffer should have been done in alsa-lib (still to be discussed) [1]. Anyway, I'm adding this to regzbot: #regzbot ^introduced 9f656705c5faa1 #regzbot title Much echoing when playing sound files on Intel Alder Lake PCH-P Audio Controller Thanks. [1]: https://lore.kernel.org/all/bb342e84-b468-8adc-6688-88da2c857da1@perex.cz/ -- An old man doll... just what I always wanted! - Clara

3 7

[PATCH v1 4/5] ASoC: tas2781: Add tas2781 driver
by Shenghao Ding 02 May '23

02 May '23

Create tas2781 driver. Signed-off-by: Shenghao Ding <13916275206(a)139.com> --- Changes in v13: - submit together with yaml, fmw lib and driver lib - extract the register operations, firmware parsing to the lib Changes to be committed: modified: sound/soc/codecs/Kconfig modified: sound/soc/codecs/Makefile new file: sound/soc/codecs/tas2781-i2c.c new file: sound/soc/codecs/tas2781-lib.c --- sound/soc/codecs/Kconfig | 19 + sound/soc/codecs/Makefile | 4 + sound/soc/codecs/tas2781-i2c.c | 704 +++++++++++++++++++++++++++++++++ sound/soc/codecs/tas2781-lib.c | 582 +++++++++++++++++++++++++++ 4 files changed, 1309 insertions(+) create mode 100644 sound/soc/codecs/tas2781-i2c.c create mode 100644 sound/soc/codecs/tas2781-lib.c diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 79d2362ad055..73f1a32ce1b7 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -234,6 +234,8 @@ config SND_SOC_ALL_CODECS imply SND_SOC_TAS2764 imply SND_SOC_TAS2770 imply SND_SOC_TAS2780 + imply SND_SOC_TAS2781_LIB + imply SND_SOC_TAS2781 imply SND_SOC_TAS5086 imply SND_SOC_TAS571X imply SND_SOC_TAS5720 @@ -1699,6 +1701,23 @@ config SND_SOC_TAS2780 Enable support for Texas Instruments TAS2780 high-efficiency digital input mono Class-D audio power amplifiers. +config SND_SOC_TAS2781_LIB + select CRC8 + select REGMAP_I2C + tristate + +config SND_SOC_TAS2781 + tristate "Texas Instruments TAS2781 speaker amplifier" + depends on I2C + select SND_SOC_TAS2781_LIB + select FW_TASDEVICE + help + Enable support for Texas Instruments TAS2781 Smart Amplifier + Digital input mono Class-D and DSP-inside audio power amplifiers. + Note the TAS2781 driver implements a flexible and configurable + algo coefficient setting, for one, two or even multiple TAS2781 + chips. + config SND_SOC_TAS5086 tristate "Texas Instruments TAS5086 speaker amplifier" depends on I2C diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 5cdbae88e6e3..fe58f2ae57c3 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -269,6 +269,8 @@ snd-soc-tas5805m-objs := tas5805m.o snd-soc-tas6424-objs := tas6424.o snd-soc-tda7419-objs := tda7419.o snd-soc-tas2770-objs := tas2770.o +snd-soc-tas2781-lib-objs := tas2781-lib.o +snd-soc-tas2781-objs := tas2781-i2c.o snd-soc-tfa9879-objs := tfa9879.o snd-soc-tfa989x-objs := tfa989x.o snd-soc-tlv320adc3xxx-objs := tlv320adc3xxx.o @@ -633,6 +635,8 @@ obj-$(CONFIG_SND_SOC_TAS2552) += snd-soc-tas2552.o obj-$(CONFIG_SND_SOC_TAS2562) += snd-soc-tas2562.o obj-$(CONFIG_SND_SOC_TAS2764) += snd-soc-tas2764.o obj-$(CONFIG_SND_SOC_TAS2780) += snd-soc-tas2780.o +obj-$(CONFIG_SND_SOC_TAS2781_LIB) += snd-soc-tas2781-lib.o +obj-$(CONFIG_SND_SOC_TAS2781) += snd-soc-tas2781.o obj-$(CONFIG_SND_SOC_TAS5086) += snd-soc-tas5086.o obj-$(CONFIG_SND_SOC_TAS571X) += snd-soc-tas571x.o obj-$(CONFIG_SND_SOC_TAS5720) += snd-soc-tas5720.o diff --git a/sound/soc/codecs/tas2781-i2c.c b/sound/soc/codecs/tas2781-i2c.c new file mode 100644 index 000000000000..aba3733036af --- /dev/null +++ b/sound/soc/codecs/tas2781-i2c.c @@ -0,0 +1,704 @@ +// SPDX-License-Identifier: GPL-2.0 +// +// ALSA SoC Texas Instruments TAS2781 Audio Smart Amplifier +// +// Copyright (C) 2022 - 2023 Texas Instruments Incorporated +// https://www.ti.com +// +// The TAS2781 driver implements a flexible and configurable +// algo coefficient setting for one, two, or even multiple +// TAS2781 chips. +// +// Author: Shenghao Ding <shenghao-ding(a)ti.com> +// Author: Kevin Lu <kevin-lu(a)ti.com> +// + +#include <linux/crc8.h> +#include <linux/firmware.h> +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_gpio.h> +#include <linux/of_irq.h> +#include <linux/regmap.h> +#include <linux/slab.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/tlv.h> +#include <sound/tas2781.h> + +static const struct i2c_device_id tasdevice_id[] = { + { "tas2781", TAS2781 }, + {} +}; + +MODULE_DEVICE_TABLE(i2c, tasdevice_id); + +static const struct of_device_id tasdevice_of_match[] = { + { .compatible = "ti,tas2781" }, + {}, +}; + +MODULE_DEVICE_TABLE(of, tasdevice_of_match); + +/** + * tas2781_digital_getvol - get the volum control + * @kcontrol: control pointer + * @ucontrol: User data + * Customer Kcontrol for tas2781 is primarily for regmap booking, paging + * depends on internal regmap mechanism. + * tas2781 contains book and page two-level register map, especially + * book switching will set the register BXXP00R7F, after switching to the + * correct book, then leverage the mechanism for paging to access the + * register. + */ +static int tas2781_digital_getvol(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + + return tasdevice_digital_getvol(tas_priv, ucontrol, mc); +} + +static int tas2781_digital_putvol(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + + return tasdevice_digital_putvol(tas_priv, ucontrol, mc); +} + +static int tas2781_amp_getvol(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + + return tasdevice_amp_getvol(tas_priv, ucontrol, mc); +} + +static int tas2781_amp_putvol(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = + snd_soc_component_get_drvdata(codec); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + + return tasdevice_amp_putvol(tas_priv, ucontrol, mc); +} + +static const struct snd_kcontrol_new tas2781_snd_controls[] = { + SOC_SINGLE_RANGE_EXT_TLV("Amp Gain Volume", TAS2781_AMP_LEVEL, + 1, 0, 20, 0, tas2781_amp_getvol, + tas2781_amp_putvol, amp_vol_tlv), + SOC_SINGLE_RANGE_EXT_TLV("Digital Volume", TAS2781_DVC_LVL, + 0, 0, 200, 1, tas2781_digital_getvol, + tas2781_digital_putvol, dvc_tlv), +}; + +static int tasdevice_set_profile_id(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + + tas_priv->rcabin.profile_cfg_id = ucontrol->value.integer.value[0]; + + return 1; +} + +static int tasdevice_info_programs(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + struct tasdevice_fw *tas_fw = tas_priv->fmw; + + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = 1; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = (int)tas_fw->nr_programs; + + return 0; +} + +static int tasdevice_info_configurations( + struct snd_kcontrol *kcontrol, struct snd_ctl_elem_info *uinfo) +{ + struct snd_soc_component *codec = + snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + struct tasdevice_fw *tas_fw = tas_priv->fmw; + + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = 1; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = (int)tas_fw->nr_configurations - 1; + + return 0; +} + +static int tasdevice_info_profile(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = 1; + uinfo->value.integer.min = 1; + uinfo->value.integer.max = max(0, tas_priv->rcabin.ncfgs); + + return 0; +} + +static int tasdevice_get_profile_id(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + + ucontrol->value.integer.value[0] = tas_priv->rcabin.profile_cfg_id; + + return 0; +} + +static int tasdevice_create_control(struct tasdevice_priv *tas_priv) +{ + struct snd_kcontrol_new *prof_ctrls; + int nr_controls = 1; + int mix_index = 0; + int ret; + char *name; + + prof_ctrls = devm_kcalloc(tas_priv->dev, nr_controls, + sizeof(prof_ctrls[0]), GFP_KERNEL); + if (!prof_ctrls) { + ret = -ENOMEM; + goto out; + } + + /* Create a mixer item for selecting the active profile */ + name = devm_kzalloc(tas_priv->dev, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, + GFP_KERNEL); + if (!name) { + ret = -ENOMEM; + goto out; + } + scnprintf(name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, "tasdev-profile-id"); + prof_ctrls[mix_index].name = name; + prof_ctrls[mix_index].iface = SNDRV_CTL_ELEM_IFACE_MIXER; + prof_ctrls[mix_index].info = tasdevice_info_profile; + prof_ctrls[mix_index].get = tasdevice_get_profile_id; + prof_ctrls[mix_index].put = tasdevice_set_profile_id; + mix_index++; + + ret = snd_soc_add_component_controls(tas_priv->codec, + prof_ctrls, nr_controls < mix_index ? nr_controls : mix_index); + +out: + return ret; +} + +static int tasdevice_program_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + + ucontrol->value.integer.value[0] = tas_priv->cur_prog; + + return 0; +} + +static int tasdevice_program_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + unsigned int nr_program = ucontrol->value.integer.value[0]; + + tas_priv->cur_prog = nr_program; + + return 1; +} + +static int tasdevice_configuration_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + + ucontrol->value.integer.value[0] = tas_priv->cur_conf; + + return 0; +} + +static int tasdevice_configuration_put( + struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + unsigned int nr_configuration = ucontrol->value.integer.value[0]; + + tas_priv->cur_conf = nr_configuration; + + return 1; +} + +static int tasdevice_dsp_create_ctrls( + struct tasdevice_priv *tas_priv) +{ + struct snd_kcontrol_new *dsp_ctrls; + char *prog_name, *conf_name; + int nr_controls = 2; + int mix_index = 0; + int ret; + + /* Alloc kcontrol via devm_kzalloc, which don't manually + * free the kcontrol + */ + dsp_ctrls = devm_kcalloc(tas_priv->dev, nr_controls, + sizeof(dsp_ctrls[0]), GFP_KERNEL); + if (!dsp_ctrls) { + ret = -ENOMEM; + goto out; + } + + /* Create a mixer item for selecting the active profile */ + prog_name = devm_kzalloc(tas_priv->dev, + SNDRV_CTL_ELEM_ID_NAME_MAXLEN, GFP_KERNEL); + conf_name = devm_kzalloc(tas_priv->dev, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, + GFP_KERNEL); + if (!prog_name || !conf_name) { + ret = -ENOMEM; + goto out; + } + + scnprintf(prog_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, + "tasdev-prog-id"); + dsp_ctrls[mix_index].name = prog_name; + dsp_ctrls[mix_index].iface = SNDRV_CTL_ELEM_IFACE_MIXER; + dsp_ctrls[mix_index].info = tasdevice_info_programs; + dsp_ctrls[mix_index].get = tasdevice_program_get; + dsp_ctrls[mix_index].put = tasdevice_program_put; + mix_index++; + + scnprintf(conf_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, + "tasdev-conf-id"); + dsp_ctrls[mix_index].name = conf_name; + dsp_ctrls[mix_index].iface = SNDRV_CTL_ELEM_IFACE_MIXER; + dsp_ctrls[mix_index].info = tasdevice_info_configurations; + dsp_ctrls[mix_index].get = tasdevice_configuration_get; + dsp_ctrls[mix_index].put = tasdevice_configuration_put; + mix_index++; + + ret = snd_soc_add_component_controls(tas_priv->codec, dsp_ctrls, + nr_controls < mix_index ? nr_controls : mix_index); + +out: + return ret; +} + +static void tasdevice_fw_ready(const struct firmware *fmw, + void *context) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)context; + int ret = 0; + int i; + + mutex_lock(&tas_priv->codec_lock); + + ret = tasdevice_rca_parser(tas_priv, fmw); + if (ret) + goto out; + tasdevice_create_control(tas_priv); + + tasdevice_dsp_remove(tas_priv); + tasdevice_calbin_remove(tas_priv); + tas_priv->fw_state = TASDEVICE_DSP_FW_PENDING; + scnprintf(tas_priv->coef_binaryname, 64, "%s_coef.bin", + tas_priv->dev_name); + ret = tasdevice_dsp_parser(tas_priv); + if (ret) { + dev_err(tas_priv->dev, "dspfw load %s error\n", + tas_priv->coef_binaryname); + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + goto out; + } + tasdevice_dsp_create_ctrls(tas_priv); + + tas_priv->fw_state = TASDEVICE_DSP_FW_ALL_OK; + + /* If calibrated data occurs error, dsp will still works with default + * calibrated data inside algo. + */ + for (i = 0; i < tas_priv->ndev; i++) { + scnprintf(tas_priv->cal_binaryname[i], 64, "%s_cal_0x%02x.bin", + tas_priv->dev_name, tas_priv->tasdevice[i].dev_addr); + ret = tas2781_load_calibration(tas_priv, + tas_priv->cal_binaryname[i], i); + if (ret != 0) + dev_err(tas_priv->dev, + "%s: load %s error, default will effect\n", + __func__, tas_priv->cal_binaryname[i]); + } + + tasdevice_prmg_calibdata_load(tas_priv, 0); + tas_priv->cur_prog = 0; +out: + if (tas_priv->fw_state == TASDEVICE_DSP_FW_FAIL) { + /*If DSP FW fail, kcontrol won't be created */ + tasdevice_config_info_remove(tas_priv); + tasdevice_dsp_remove(tas_priv); + } + mutex_unlock(&tas_priv->codec_lock); + if (fmw) + release_firmware(fmw); +} + +static int tasdevice_dapm_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *codec = snd_soc_dapm_to_component(w->dapm); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + int state = 0; + + /* Codec Lock Hold */ + mutex_lock(&tas_priv->codec_lock); + if (event == SND_SOC_DAPM_PRE_PMD) + state = 1; + tasdevice_tuning_switch(tas_priv, state); + /* Codec Lock Release*/ + mutex_unlock(&tas_priv->codec_lock); + + return 0; +} + +static const struct snd_soc_dapm_widget tasdevice_dapm_widgets[] = { + SND_SOC_DAPM_AIF_IN("ASI", "ASI Playback", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_OUT_E("ASI OUT", "ASI Capture", 0, SND_SOC_NOPM, + 0, 0, tasdevice_dapm_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_SPK("SPK", tasdevice_dapm_event), + SND_SOC_DAPM_OUTPUT("OUT"), + SND_SOC_DAPM_INPUT("DMIC") +}; + +static const struct snd_soc_dapm_route tasdevice_audio_map[] = { + {"SPK", NULL, "ASI"}, + {"OUT", NULL, "SPK"}, + {"ASI OUT", NULL, "DMIC"} +}; + +static int tasdevice_startup(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct snd_soc_component *codec = dai->component; + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + int ret = 0; + + if (tas_priv->fw_state != TASDEVICE_DSP_FW_ALL_OK) { + dev_err(tas_priv->dev, "DSP bin file not loaded\n"); + ret = -EINVAL; + } + + return ret; +} + +static int tasdevice_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, struct snd_soc_dai *dai) +{ + struct tasdevice_priv *tas_priv = snd_soc_dai_get_drvdata(dai); + unsigned int slot_width; + unsigned int fsrate; + int bclk_rate; + int rc = 0; + + fsrate = params_rate(params); + switch (fsrate) { + case 48000: + case 44100: + break; + default: + dev_err(tas_priv->dev, "%s: incorrect sample rate = %u\n", + __func__, fsrate); + rc = -EINVAL; + goto out; + } + + slot_width = params_width(params); + switch (slot_width) { + case 16: + case 20: + case 24: + case 32: + break; + default: + dev_err(tas_priv->dev, "%s: incorrect slot width = %u\n", + __func__, slot_width); + rc = -EINVAL; + goto out; + } + + bclk_rate = snd_soc_params_to_bclk(params); + if (bclk_rate < 0) { + dev_err(tas_priv->dev, "%s: incorrect bclk rate = %d\n", + __func__, bclk_rate); + rc = bclk_rate; + goto out; + } + +out: + return rc; +} + +static int tasdevice_set_dai_sysclk(struct snd_soc_dai *codec_dai, + int clk_id, unsigned int freq, int dir) +{ + struct tasdevice_priv *tas_priv = snd_soc_dai_get_drvdata(codec_dai); + + tas_priv->sysclk = freq; + + return 0; +} + +static const struct snd_soc_dai_ops tasdevice_dai_ops = { + .startup = tasdevice_startup, + .hw_params = tasdevice_hw_params, + .set_sysclk = tasdevice_set_dai_sysclk, +}; + +static struct snd_soc_dai_driver tasdevice_dai_driver[] = { + { + .name = "tas2781_codec", + .id = 0, + .playback = { + .stream_name = "Playback", + .channels_min = 1, + .channels_max = 4, + .rates = TASDEVICE_RATES, + .formats = TASDEVICE_FORMATS, + }, + .capture = { + .stream_name = "Capture", + .channels_min = 1, + .channels_max = 4, + .rates = TASDEVICE_RATES, + .formats = TASDEVICE_FORMATS, + }, + .ops = &tasdevice_dai_ops, + .symmetric_rate = 1, + }, +}; + +static int tasdevice_codec_probe(struct snd_soc_component *codec) +{ + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + + return tascodec_init(tas_priv, codec, tasdevice_fw_ready); +} + +static void tasdevice_deinit(void *context) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + + tasdevice_config_info_remove(tas_priv); + tasdevice_dsp_remove(tas_priv); + tasdevice_calbin_remove(tas_priv); + tas_priv->fw_state = TASDEVICE_DSP_FW_PENDING; +} + +static void tasdevice_codec_remove( + struct snd_soc_component *codec) +{ + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + + tasdevice_deinit(tas_priv); +} + +static const struct snd_soc_component_driver + soc_codec_driver_tasdevice = { + .probe = tasdevice_codec_probe, + .remove = tasdevice_codec_remove, + .controls = tas2781_snd_controls, + .num_controls = ARRAY_SIZE(tas2781_snd_controls), + .dapm_widgets = tasdevice_dapm_widgets, + .num_dapm_widgets = ARRAY_SIZE(tasdevice_dapm_widgets), + .dapm_routes = tasdevice_audio_map, + .num_dapm_routes = ARRAY_SIZE(tasdevice_audio_map), + .idle_bias_on = 1, + .endianness = 1, +}; + +static void tasdevice_parse_dt(struct tasdevice_priv *tas_priv) +{ + struct i2c_client *client = (struct i2c_client *)tas_priv->client; + unsigned int dev_addrs[max_chn]; + int rc, i, ndev; + + if (tas_priv->isacpi) { + ndev = device_property_read_u32_array(&client->dev, + "ti,audio-slots", NULL, 0); + if (ndev <= 0) { + ndev = 1; + dev_addrs[0] = client->addr; + } else { + ndev = (ndev < ARRAY_SIZE(dev_addrs)) + ? ndev : ARRAY_SIZE(dev_addrs); + ndev = device_property_read_u32_array(&client->dev, + "ti,audio-slots", dev_addrs, ndev); + } + + tas_priv->irq_info.irq_gpio = + acpi_dev_gpio_irq_get(ACPI_COMPANION(&client->dev), 0); + } else { + struct device_node *np = tas_priv->dev->of_node; + + ndev = of_property_read_variable_u32_array(np, + "ti,audio-slots", dev_addrs, 0, ARRAY_SIZE(dev_addrs)); + if (ndev <= 0) { + ndev = 1; + dev_addrs[0] = client->addr; + } + tas_priv->irq_info.irq_gpio = of_irq_get(np, 0); + } + tas_priv->ndev = ndev; + for (i = 0; i < ndev; i++) + tas_priv->tasdevice[i].dev_addr = dev_addrs[i]; + + if (ndev > 1) { + rc = device_property_read_u32(&client->dev, + "ti,broadcast-addr", + &(tas_priv->glb_addr.dev_addr)); + if (rc) { + dev_err(tas_priv->dev, + "Looking up broadcast-addr failed %d\n", rc); + tas_priv->glb_addr.dev_addr = 0; + } + } + + tas_priv->reset = devm_gpiod_get_optional(&client->dev, + "reset-gpios", GPIOD_OUT_HIGH); + if (IS_ERR(tas_priv->reset)) + dev_err(tas_priv->dev, "%s Can't get reset GPIO\n", + __func__); + + strcpy(tas_priv->dev_name, tasdevice_id[tas_priv->chip_id].name); + + if (gpio_is_valid(tas_priv->irq_info.irq_gpio)) { + rc = gpio_request(tas_priv->irq_info.irq_gpio, + "AUDEV-IRQ"); + if (!rc) { + gpio_direction_input( + tas_priv->irq_info.irq_gpio); + + tas_priv->irq_info.irq = + gpio_to_irq(tas_priv->irq_info.irq_gpio); + } else + dev_err(tas_priv->dev, "%s: GPIO %d request error\n", + __func__, tas_priv->irq_info.irq_gpio); + } else + dev_err(tas_priv->dev, + "Looking up irq-gpio property failed %d\n", + tas_priv->irq_info.irq_gpio); +} + +static int tasdevice_i2c_probe(struct i2c_client *i2c) +{ + const struct i2c_device_id *id = i2c_match_id(tasdevice_id, i2c); + const struct acpi_device_id *acpi_id; + struct tasdevice_priv *tas_priv; + int ret; + + tas_priv = tasdevice_kzalloc(i2c); + if (!tas_priv) + return -ENOMEM; + + if (ACPI_HANDLE(&i2c->dev)) { + acpi_id = acpi_match_device(i2c->dev.driver->acpi_match_table, + &i2c->dev); + if (!acpi_id) { + dev_err(&i2c->dev, "No driver data\n"); + ret = -EINVAL; + goto err; + } + tas_priv->chip_id = acpi_id->driver_data; + tas_priv->isacpi = true; + } else { + tas_priv->chip_id = id ? id->driver_data : 0; + tas_priv->isacpi = false; + } + + tasdevice_parse_dt(tas_priv); + + ret = tasdevice_init(tas_priv); + if (ret) + goto err; + + ret = devm_snd_soc_register_component(tas_priv->dev, + &soc_codec_driver_tasdevice, + tasdevice_dai_driver, ARRAY_SIZE(tasdevice_dai_driver)); + if (ret) { + dev_err(tas_priv->dev, "%s: codec register error:0x%08x\n", + __func__, ret); + goto err; + } +err: + if (ret < 0) + tasdevice_remove(tas_priv); + return ret; +} + +static void tasdevice_i2c_remove(struct i2c_client *client) +{ + struct tasdevice_priv *tas_priv = i2c_get_clientdata(client); + + tasdevice_remove(tas_priv); +} + +#ifdef CONFIG_ACPI +static const struct acpi_device_id tasdevice_acpi_match[] = { + { "TAS2781", TAS2781 }, + {}, +}; + +MODULE_DEVICE_TABLE(acpi, tasdevice_acpi_match); +#endif + +static struct i2c_driver tasdevice_i2c_driver = { + .driver = { + .name = "tas2781-codec", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(tasdevice_of_match), +#ifdef CONFIG_ACPI + .acpi_match_table = ACPI_PTR(tasdevice_acpi_match), +#endif + }, + .probe = tasdevice_i2c_probe, + .remove = tasdevice_i2c_remove, + .id_table = tasdevice_id, +}; + +module_i2c_driver(tasdevice_i2c_driver); + +MODULE_AUTHOR("Shenghao Ding <shenghao-ding(a)ti.com>"); +MODULE_AUTHOR("Kevin Lu <kevin-lu(a)ti.com>"); +MODULE_DESCRIPTION("ASoC TAS2781 Driver"); +MODULE_LICENSE("GPL"); +MODULE_IMPORT_NS(FW_TASDEVICE); diff --git a/sound/soc/codecs/tas2781-lib.c b/sound/soc/codecs/tas2781-lib.c new file mode 100644 index 000000000000..8b0f66cea4fe --- /dev/null +++ b/sound/soc/codecs/tas2781-lib.c @@ -0,0 +1,582 @@ +// SPDX-License-Identifier: GPL-2.0 +// +// tas2781-lib.c -- TAS2781 Common functions for HDA and ASoC Audio drivers +// +// Copyright 2023 Texas Instruments, Inc. +// +// Author: Shenghao Ding <shenghao-ding(a)ti.com> + +#include <linux/crc8.h> +#include <linux/firmware.h> +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_gpio.h> +#include <linux/of_irq.h> +#include <linux/regmap.h> +#include <linux/slab.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/tlv.h> +#include <sound/tas2781.h> + +#define TASDEVICE_CRC8_POLYNOMIAL 0x4d + +static const struct regmap_range_cfg tasdevice_ranges[] = { + { + .range_min = 0, + .range_max = 256 * 128, + .selector_reg = TASDEVICE_PAGE_SELECT, + .selector_mask = 0xff, + .selector_shift = 0, + .window_start = 0, + .window_len = 128, + }, +}; + +static const struct regmap_config tasdevice_regmap = { + .reg_bits = 16, + .val_bits = 8, + .cache_type = REGCACHE_RBTREE, + .ranges = tasdevice_ranges, + .num_ranges = ARRAY_SIZE(tasdevice_ranges), + .max_register = 256 * 128, +}; + +static int tasdevice_change_chn_book(struct tasdevice_priv *tas_priv, + enum channel chn, int book) +{ + struct i2c_client *client = (struct i2c_client *)tas_priv->client; + int ret = 0; + int i; + + if (chn < tas_priv->ndev) { + struct tasdevice *tasdev = &tas_priv->tasdevice[chn]; + + if (tas_priv->glb_addr.ref_cnt != 0) { + tas_priv->glb_addr.ref_cnt = 0; + tas_priv->glb_addr.cur_book = -1; + } + client->addr = tasdev->dev_addr; + if (tasdev->cur_book != book) { + ret = regmap_write(tas_priv->regmap, + TASDEVICE_BOOKCTL_REG, book); + if (ret < 0) { + dev_err(tas_priv->dev, "%s, E=%d\n", + __func__, ret); + goto out; + } + tasdev->cur_book = book; + } + } else if (chn == tas_priv->ndev) { + struct global_addr *glb_addr = &tas_priv->glb_addr; + + /* Chn == device number will enable global broadcast mode*/ + if (tas_priv->glb_addr.ref_cnt == 0) + for (i = 0; i < tas_priv->ndev; i++) + tas_priv->tasdevice[i].cur_book = -1; + client->addr = glb_addr->dev_addr; + if (glb_addr->cur_book != book) { + ret = regmap_write(tas_priv->regmap, + TASDEVICE_BOOKCTL_REG, book); + if (ret < 0) { + dev_err(tas_priv->dev, "%s, book%x, E=%d\n", + __func__, book, ret); + goto out; + } + glb_addr->cur_book = book; + } + + glb_addr->ref_cnt++; + } else { + ret = -EINVAL; + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + } + +out: + return ret; +} + +int tasdevice_dev_read(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned int *val) +{ + int ret = 0; + + if (chn < tas_priv->ndev) { + ret = tasdevice_change_chn_book(tas_priv, chn, + TASDEVICE_BOOK_ID(reg)); + if (ret < 0) + goto out; + + ret = regmap_read(tas_priv->regmap, TASDEVICE_PGRG(reg), val); + if (ret < 0) + dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret); + } else { + ret = -EINVAL; + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + } + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_dev_read); + +int tasdevice_dev_write(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned int value) +{ + int ret = 0; + + /* chn <= tas_dev->ndev will support global broadcast mode*/ + if (chn <= tas_priv->ndev) { + ret = tasdevice_change_chn_book(tas_priv, chn, + TASDEVICE_BOOK_ID(reg)); + if (ret < 0) + goto out; + + ret = regmap_write(tas_priv->regmap, TASDEVICE_PGRG(reg), + value); + if (ret < 0) + dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret); + } else { + ret = -EINVAL; + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + } + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_dev_write); + +int tasdevice_dev_bulk_write( + struct tasdevice_priv *tas_priv, enum channel chn, + unsigned int reg, unsigned char *data, + unsigned int len) +{ + int ret = 0; + + /* chn <= tas_dev->ndev will support global broadcast mode*/ + if (chn <= tas_priv->ndev) { + ret = tasdevice_change_chn_book(tas_priv, chn, + TASDEVICE_BOOK_ID(reg)); + if (ret < 0) + goto out; + + ret = regmap_bulk_write(tas_priv->regmap, TASDEVICE_PGRG(reg), + data, len); + if (ret < 0) + dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret); + } else { + ret = -EINVAL; + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + } + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_dev_bulk_write); + +int tasdevice_dev_bulk_read(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned char *data, + unsigned int len) +{ + int ret = 0; + + if (chn < tas_priv->ndev) { + ret = tasdevice_change_chn_book(tas_priv, chn, + TASDEVICE_BOOK_ID(reg)); + if (ret < 0) + goto out; + + ret = regmap_bulk_read(tas_priv->regmap, TASDEVICE_PGRG(reg), + data, len); + if (ret < 0) + dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret); + } else + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_dev_bulk_read); + +int tasdevice_dev_update_bits( + struct tasdevice_priv *tas_priv, enum channel chn, + unsigned int reg, unsigned int mask, unsigned int value) +{ + int ret = 0; + + /* update-bits can't support global broadcast mode, + * because this operation contains a reading operation + * for register value. In global mode, reading register + * from all of the tas2781 will cause confusion. + */ + if (chn < tas_priv->ndev) { + ret = tasdevice_change_chn_book(tas_priv, chn, + TASDEVICE_BOOK_ID(reg)); + if (ret < 0) + goto out; + + ret = regmap_update_bits(tas_priv->regmap, + TASDEVICE_PGRG(reg), mask, value); + if (ret < 0) + dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret); + } else { + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + ret = -EINVAL; + } + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_dev_update_bits); + +/* Only register write and bulk write support global mode + * Other cases, such as bits update, register read and bulk + * only support device-by-device operation + */ +static void tas2781_set_global_mode(struct tasdevice_priv *tas_priv) +{ + int i, ret; + + for (i = 0; i < tas_priv->ndev; i++) { + ret = tasdevice_dev_update_bits(tas_priv, i, + TAS2781_MISC_CFG2, TAS2781_GLOBAL_ADDR_MASK, + TAS2781_GLOBAL_ADDR_ENABLE); + if (ret < 0) { + dev_err(tas_priv->dev, "%s: chn %d set glb fail, %d\n", + __func__, i, ret); + continue; + } + } +} + +struct tasdevice_priv *tasdevice_kzalloc(struct i2c_client *i2c) +{ + struct tasdevice_priv *tas_priv; + + tas_priv = devm_kzalloc(&i2c->dev, sizeof(*tas_priv), GFP_KERNEL); + if (!tas_priv) + return NULL; + tas_priv->dev = &i2c->dev; + tas_priv->client = (void *)i2c; + + return tas_priv; +} +EXPORT_SYMBOL_GPL(tasdevice_kzalloc); + +void tas2781_reset(struct tasdevice_priv *tas_dev) +{ + int ret, i; + + if (tas_dev->reset) { + gpiod_set_value_cansleep(tas_dev->reset, 0); + usleep_range(500, 1000); + gpiod_set_value_cansleep(tas_dev->reset, 1); + } else { + for (i = 0; i < tas_dev->ndev; i++) { + ret = tasdevice_dev_write(tas_dev, i, + TAS2781_REG_SWRESET, + TAS2781_REG_SWRESET_RESET); + if (ret < 0) + dev_err(tas_dev->dev, + "dev %d swreset fail, %d\n", + i, ret); + } + } + usleep_range(1000, 1050); +} +EXPORT_SYMBOL_GPL(tas2781_reset); + +int tascodec_init(struct tasdevice_priv *tas_priv, void *codec, + void (*cont)(const struct firmware *fw, void *context)) +{ + int ret = 0; + + /* Codec Lock Hold to ensure that codec_probe and firmware parsing and + * loading do not simultaneously execute. + */ + mutex_lock(&tas_priv->codec_lock); + + scnprintf(tas_priv->rca_binaryname, 64, "%srca%d.bin", + tas_priv->dev_name, tas_priv->ndev); + crc8_populate_msb(tas_priv->crc8_lkp_tbl, TASDEVICE_CRC8_POLYNOMIAL); + tas_priv->codec = codec; + ret = request_firmware_nowait(THIS_MODULE, FW_ACTION_UEVENT, + tas_priv->rca_binaryname, tas_priv->dev, GFP_KERNEL, tas_priv, + cont); + if (ret) + dev_err(tas_priv->dev, "request_firmware_nowait err:0x%08x\n", + ret); + + tas2781_reset(tas_priv); + if (tas_priv->set_global_mode) + tas_priv->set_global_mode(tas_priv); + + /* Codec Lock Release*/ + mutex_unlock(&tas_priv->codec_lock); + return ret; +} +EXPORT_SYMBOL_GPL(tascodec_init); + +int tasdevice_init(struct tasdevice_priv *tas_priv) +{ + int ret = 0; + int i; + + tas_priv->regmap = devm_regmap_init_i2c(tas_priv->client, + &tasdevice_regmap); + if (IS_ERR(tas_priv->regmap)) { + ret = PTR_ERR(tas_priv->regmap); + dev_err(tas_priv->dev, "Failed to allocate register map: %d\n", + ret); + goto out; + } + + tas_priv->cur_prog = -1; + tas_priv->cur_conf = -1; + + for (i = 0; i < tas_priv->ndev; i++) { + tas_priv->tasdevice[i].cur_book = -1; + tas_priv->tasdevice[i].cur_prog = -1; + tas_priv->tasdevice[i].cur_conf = -1; + } + + if (tas_priv->glb_addr.dev_addr != 0 + && tas_priv->glb_addr.dev_addr < 0x7F) + tas_priv->set_global_mode = tas2781_set_global_mode; + dev_set_drvdata(tas_priv->dev, tas_priv); + + mutex_init(&tas_priv->codec_lock); + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_init); + +static void tasdev_dsp_prog_blk_remove(struct tasdevice_prog *prog) +{ + struct tasdevice_data *im; + struct tasdev_blk *blk; + unsigned int nr_blk; + + if (!prog) + return; + + im = &(prog->dev_data); + + if (!im->dev_blks) + return; + + for (nr_blk = 0; nr_blk < im->nr_blk; nr_blk++) { + blk = &(im->dev_blks[nr_blk]); + kfree(blk->data); + } + kfree(im->dev_blks); +} + +static void tasdev_dsp_prog_remove(struct tasdevice_prog *prog, + unsigned short nr) +{ + int i; + + for (i = 0; i < nr; i++) + tasdev_dsp_prog_blk_remove(&prog[i]); + kfree(prog); +} + +static void tasdev_dsp_cfg_blk_remove(struct tasdevice_config *cfg) +{ + struct tasdevice_data *im; + struct tasdev_blk *blk; + unsigned int nr_blk; + + if (cfg) { + im = &(cfg->dev_data); + + if (!im->dev_blks) + return; + + for (nr_blk = 0; nr_blk < im->nr_blk; nr_blk++) { + blk = &(im->dev_blks[nr_blk]); + kfree(blk->data); + } + kfree(im->dev_blks); + } +} + +static void tasdev_dsp_cfg_remove(struct tasdevice_config *config, + unsigned short nr) +{ + int i; + + for (i = 0; i < nr; i++) + tasdev_dsp_cfg_blk_remove(&config[i]); + kfree(config); +} + +void tasdevice_dsp_remove(void *context) +{ + struct tasdevice_priv *tas_dev = (struct tasdevice_priv *) context; + struct tasdevice_fw *tas_fmw = tas_dev->fmw; + + if (!tas_dev->fmw) + return; + + if (tas_fmw->programs) + tasdev_dsp_prog_remove(tas_fmw->programs, + tas_fmw->nr_programs); + if (tas_fmw->configs) + tasdev_dsp_cfg_remove(tas_fmw->configs, + tas_fmw->nr_configurations); + kfree(tas_fmw); + tas_dev->fmw = NULL; +} +EXPORT_SYMBOL_GPL(tasdevice_dsp_remove); + +void tasdevice_remove(struct tasdevice_priv *tas_priv) +{ + if (gpio_is_valid(tas_priv->irq_info.irq_gpio)) + gpio_free(tas_priv->irq_info.irq_gpio); + kfree(tas_priv->acpi_subsystem_id); + mutex_destroy(&tas_priv->codec_lock); +} +EXPORT_SYMBOL_GPL(tasdevice_remove); + +static int tasdevice_clamp(int val, int max, unsigned int invert) +{ + if (val > max) + val = max; + if (invert) + val = max - val; + if (val < 0) + val = 0; + return val; +} + +int tasdevice_amp_putvol(struct tasdevice_priv *tas_priv, + struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc) +{ + unsigned int invert = mc->invert; + unsigned char mask; + int max = mc->max; + int err_cnt = 0; + int val, i, ret; + + mask = (1 << fls(max)) - 1; + mask <<= mc->shift; + val = tasdevice_clamp(ucontrol->value.integer.value[0], max, invert); + for (i = 0; i < tas_priv->ndev; i++) { + ret = tasdevice_dev_update_bits(tas_priv, i, + mc->reg, mask, (unsigned int)(val << mc->shift)); + if (!ret) + continue; + err_cnt++; + dev_err(tas_priv->dev, "set AMP vol error in dev %d\n", i); + } + + /* All the devices set error, return 0 */ + return (err_cnt == tas_priv->ndev) ? 0 : 1; +} +EXPORT_SYMBOL_GPL(tasdevice_amp_putvol); + +int tasdevice_amp_getvol(struct tasdevice_priv *tas_priv, + struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc) +{ + unsigned int invert = mc->invert; + unsigned char mask = 0; + int max = mc->max; + int ret = 0; + int val; + + /* Read the primary device */ + ret = tasdevice_dev_read(tas_priv, 0, mc->reg, &val); + if (ret) { + dev_err(tas_priv->dev, "%s, get AMP vol error\n", __func__); + goto out; + } + + mask = (1 << fls(max)) - 1; + mask <<= mc->shift; + val = (val & mask) >> mc->shift; + val = tasdevice_clamp(val, max, invert); + ucontrol->value.integer.value[0] = val; + +out: + return ret; + +} +EXPORT_SYMBOL_GPL(tasdevice_amp_getvol); + +int tasdevice_digital_putvol(struct tasdevice_priv *tas_priv, + struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc) +{ + unsigned int invert = mc->invert; + int max = mc->max; + int err_cnt = 0; + int ret = 1; + int val, i; + + val = tasdevice_clamp(ucontrol->value.integer.value[0], max, invert); + + if (tas_priv->set_global_mode) { + ret = tasdevice_dev_write(tas_priv, tas_priv->ndev, + mc->reg, (unsigned int)val); + if (ret) + dev_err(tas_priv->dev, "%s, error in global mode\n", + __func__); + } + + if (!tas_priv->set_global_mode || ret != 0) { + for (i = 0; i < tas_priv->ndev; i++) { + ret = tasdevice_dev_write(tas_priv, i, mc->reg, + (unsigned int)val); + if (!ret) + continue; + err_cnt++; + dev_err(tas_priv->dev, + "set digital vol err in dev %d\n", i); + } + } + + /* All the devices set error, return 0 */ + return (err_cnt == tas_priv->ndev) ? 0 : 1; + +} +EXPORT_SYMBOL_GPL(tasdevice_digital_putvol); + +int tasdevice_digital_getvol(struct tasdevice_priv *tas_priv, + struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc) +{ + unsigned int invert = mc->invert; + int max = mc->max; + int ret, val; + + /* Read the primary device as the whole */ + ret = tasdevice_dev_read(tas_priv, 0, mc->reg, &val); + if (ret) { + dev_err(tas_priv->dev, "%s, get digital vol error\n", + __func__); + goto out; + } + + val = tasdevice_clamp(val, max, invert); + ucontrol->value.integer.value[0] = val; + +out: + return ret; + +} +EXPORT_SYMBOL_GPL(tasdevice_digital_getvol); + +MODULE_DESCRIPTION("TAS2781 library"); +MODULE_AUTHOR("Shenghao Ding, TI, <shenghao-ding(a)ti.com>"); +MODULE_LICENSE("GPL"); -- 2.34.1

2 2

[PATCH] ALSA: hda/realtek: Add quirk for ASUS UM3402YAR using CS35L41
by Mark Asselstine 02 May '23

02 May '23

This Asus Zenbook laptop uses Realtek HDA codec combined with 2xCS35L41 Amplifiers using I2C with External Boost. Signed-off-by: Mark Asselstine <asselsm(a)gmail.com> --- sound/pci/hda/patch_realtek.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index f70d6a33421d..905acd66ea01 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -9500,6 +9500,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x1043, 0x1427, "Asus Zenbook UX31E", ALC269VB_FIXUP_ASUS_ZENBOOK), SND_PCI_QUIRK(0x1043, 0x1517, "Asus Zenbook UX31A", ALC269VB_FIXUP_ASUS_ZENBOOK_UX31A), SND_PCI_QUIRK(0x1043, 0x1662, "ASUS GV301QH", ALC294_FIXUP_ASUS_DUAL_SPK), + SND_PCI_QUIRK(0x1043, 0x1683, "ASUS UM3402YAR", ALC287_FIXUP_CS35L41_I2C_2), SND_PCI_QUIRK(0x1043, 0x16b2, "ASUS GU603", ALC289_FIXUP_ASUS_GA401), SND_PCI_QUIRK(0x1043, 0x16e3, "ASUS UX50", ALC269_FIXUP_STEREO_DMIC), SND_PCI_QUIRK(0x1043, 0x1740, "ASUS UX430UA", ALC295_FIXUP_ASUS_DACS), -- 2.40.1

2 1

[PATCH v1 2/5] ASoC: dt-bindings: Add tas2781 amplifier
by Shenghao Ding 02 May '23

02 May '23

Create tas2781.yaml for tas2781 driver. Signed-off-by: Shenghao Ding <13916275206(a)139.com> --- Changes in v1: - Submit together with tas2781 codec driver code Changes to be committed: new file: Documentation/devicetree/bindings/sound/ti,tas2781.yaml --- .../devicetree/bindings/sound/ti,tas2781.yaml | 84 +++++++++++++++++++ 1 file changed, 84 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/ti,tas2781.yaml diff --git a/Documentation/devicetree/bindings/sound/ti,tas2781.yaml b/Documentation/devicetree/bindings/sound/ti,tas2781.yaml new file mode 100644 index 000000000000..028151c388bf --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ti,tas2781.yaml @@ -0,0 +1,84 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2022 - 2023 Texas Instruments Incorporated +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/ti,tas2781.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments TAS2781 SmartAMP + +maintainers: + - Shenghao Ding <shenghao-ding(a)ti.com> + +description: + The TAS2781 is a mono, digital input Class-D audio amplifier + optimized for efficiently driving high peak power into small + loudspeakers. Integrated an on-chip DSP supports Texas Instruments + Smart Amp speaker protection algorithm. The integrated speaker + voltage and current sense provides for real time + monitoring of loudspeaker behavior. + +properties: + compatible: + enum: + - ti,tas2781 + + reg: + description: I2C address of the primary device. + items: + minimum: 0x38 + maximum: 0x40 + + reset-gpios: + maxItems: 1 + + interrupts: + maxItems: 1 + + ti,audio-slots: + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 4 + description: + I2C address of the device for different audio slots, + useless in mono case. + + ti,broadcast-addr: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Generic I2C address for all the tas2781 devices in + purpose of I2C broadcast during the multi-device + writes, useless in mono case. + + '#sound-dai-cells': + const: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + i2c { + /* example with quad support, such as tablet or pad device */ + #address-cells = <1>; + #size-cells = <0>; + quad: codec@38 { + compatible = "ti,tas2781"; + reg = <0x38>; + #sound-dai-cells = <1>; + reset-gpios = < &gpio1 10 GPIO_ACTIVE_HIGH >; + interrupt-parent = <&gpio1>; + interrupts = <15>; + ti,audio-slots = < 0x38 /* topleft-channel */ + 0x39 /* topright-channel */ + 0x3a /* bottomleft-channel */ + 0x3b /* bottomright-channel */ + >; + ti,broadcast-addr = <0x40>; + }; + }; +... -- 2.34.1

2 1

[PATCH v1 5/5] ALSA: hda/tas2781: Add tas2781 HDA driver
by Shenghao Ding 02 May '23

02 May '23

Create tas2781 HDA driver. Signed-off-by: Shenghao Ding <13916275206(a)139.com> --- Changes in v1: - Initial Changes to be committed: modified: sound/pci/hda/Kconfig modified: sound/pci/hda/Makefile modified: sound/pci/hda/patch_realtek.c new file: sound/pci/hda/tas2781_hda_i2c.c --- sound/pci/hda/Kconfig | 15 + sound/pci/hda/Makefile | 2 + sound/pci/hda/patch_realtek.c | 106 ++++- sound/pci/hda/tas2781_hda_i2c.c | 805 ++++++++++++++++++++++++++++++++ 4 files changed, 925 insertions(+), 3 deletions(-) create mode 100644 sound/pci/hda/tas2781_hda_i2c.c diff --git a/sound/pci/hda/Kconfig b/sound/pci/hda/Kconfig index 886255a03e8b..3cd8358cbf38 100644 --- a/sound/pci/hda/Kconfig +++ b/sound/pci/hda/Kconfig @@ -130,6 +130,21 @@ config SND_HDA_SCODEC_CS35L41_SPI comment "Set to Y if you want auto-loading the side codec driver" depends on SND_HDA=y && SND_HDA_SCODEC_CS35L41_SPI=m +config SND_HDA_SCODEC_TAS2781_I2C + tristate "Build TAS2781 HD-audio side codec support for I2C Bus" + depends on I2C + depends on ACPI + depends on SND_SOC + select SND_SOC_TAS2781_LIB + select FW_TASDEVICE + select CRC32_SARWATE + help + Say Y or M here to include TAS2781 I2C HD-audio side codec support + in snd-hda-intel driver, such as ALC287. + +comment "Set to Y if you want auto-loading the side codec driver" + depends on SND_HDA=y && SND_HDA_SCODEC_TAS2781_I2C=m + config SND_HDA_CODEC_REALTEK tristate "Build Realtek HD-audio codec support" select SND_HDA_GENERIC diff --git a/sound/pci/hda/Makefile b/sound/pci/hda/Makefile index 00d306104484..1c76609690d6 100644 --- a/sound/pci/hda/Makefile +++ b/sound/pci/hda/Makefile @@ -32,6 +32,7 @@ snd-hda-scodec-cs35l41-objs := cs35l41_hda.o snd-hda-scodec-cs35l41-i2c-objs := cs35l41_hda_i2c.o snd-hda-scodec-cs35l41-spi-objs := cs35l41_hda_spi.o snd-hda-cs-dsp-ctls-objs := hda_cs_dsp_ctl.o +snd-hda-scodec-tas2781-i2c-objs := tas2781_hda_i2c.o # common driver obj-$(CONFIG_SND_HDA) := snd-hda-codec.o @@ -56,6 +57,7 @@ obj-$(CONFIG_SND_HDA_SCODEC_CS35L41) += snd-hda-scodec-cs35l41.o obj-$(CONFIG_SND_HDA_SCODEC_CS35L41_I2C) += snd-hda-scodec-cs35l41-i2c.o obj-$(CONFIG_SND_HDA_SCODEC_CS35L41_SPI) += snd-hda-scodec-cs35l41-spi.o obj-$(CONFIG_SND_HDA_CS_DSP_CONTROLS) += snd-hda-cs-dsp-ctls.o +obj-$(CONFIG_SND_HDA_SCODEC_TAS2781_I2C) += snd-hda-scodec-tas2781-i2c.o # this must be the last entry after codec drivers; # otherwise the codec patches won't be hooked before the PCI probe diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index f70d6a33421d..807c5f62b055 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -6705,7 +6705,7 @@ static void comp_generic_playback_hook(struct hda_pcm_stream *hinfo, struct hda_ } } -struct cs35l41_dev_name { +struct scodec_dev_name { const char *bus; const char *hid; int index; @@ -6714,7 +6714,7 @@ struct cs35l41_dev_name { /* match the device name in a slightly relaxed manner */ static int comp_match_cs35l41_dev_name(struct device *dev, void *data) { - struct cs35l41_dev_name *p = data; + struct scodec_dev_name *p = data; const char *d = dev_name(dev); int n = strlen(p->bus); char tmp[32]; @@ -6730,12 +6730,31 @@ static int comp_match_cs35l41_dev_name(struct device *dev, void *data) return !strcmp(d + n, tmp); } +static int comp_match_tas2781_dev_name(struct device *dev, void *data) +{ + struct scodec_dev_name *p = data; + const char *d = dev_name(dev); + int n = strlen(p->bus); + char tmp[32]; + + /* check the bus name */ + if (strncmp(d, p->bus, n)) + return 0; + /* skip the bus number */ + if (isdigit(d[n])) + n++; + /* the rest must be exact matching */ + snprintf(tmp, sizeof(tmp), "-%s:00", p->hid); + + return !strcmp(d + n, tmp); +} + static void cs35l41_generic_fixup(struct hda_codec *cdc, int action, const char *bus, const char *hid, int count) { struct device *dev = hda_codec_dev(cdc); struct alc_spec *spec = cdc->spec; - struct cs35l41_dev_name *rec; + struct scodec_dev_name *rec; int ret, i; switch (action) { @@ -6760,6 +6779,40 @@ static void cs35l41_generic_fixup(struct hda_codec *cdc, int action, const char } } +static void tas2781_generic_fixup(struct hda_codec *cdc, int action, + const char *bus, const char *hid, int count) +{ + struct device *dev = hda_codec_dev(cdc); + struct alc_spec *spec = cdc->spec; + struct scodec_dev_name *rec; + int ret, i; + + switch (action) { + case HDA_FIXUP_ACT_PRE_PROBE: + for (i = 0; i < count; i++) { + rec = devm_kmalloc(dev, sizeof(*rec), GFP_KERNEL); + if (!rec) + return; + rec->bus = bus; + rec->hid = hid; + rec->index = i; + spec->comps[i].codec = cdc; + component_match_add(dev, &spec->match, + comp_match_tas2781_dev_name, rec); + } + ret = component_master_add_with_match(dev, &comp_master_ops, + spec->match); + if (ret) + codec_err(cdc, + "Fail to register component aggregator %d\n", + ret); + else + spec->gen.pcm_playback_hook = + comp_generic_playback_hook; + break; + } +} + static void cs35l41_fixup_i2c_two(struct hda_codec *cdc, const struct hda_fixup *fix, int action) { cs35l41_generic_fixup(cdc, action, "i2c", "CSC3551", 2); @@ -6787,6 +6840,12 @@ static void alc287_fixup_legion_16ithg6_speakers(struct hda_codec *cdc, const st cs35l41_generic_fixup(cdc, action, "i2c", "CLSA0101", 2); } +static void tas2781_fixup_i2c(struct hda_codec *cdc, + const struct hda_fixup *fix, int action) +{ + tas2781_generic_fixup(cdc, action, "i2c", "TIAS2781", 1); +} + /* for alc295_fixup_hp_top_speakers */ #include "hp_x360_helper.c" @@ -7201,6 +7260,8 @@ enum { ALC287_FIXUP_YOGA9_14IAP7_BASS_SPK_PIN, ALC295_FIXUP_DELL_INSPIRON_TOP_SPEAKERS, ALC236_FIXUP_DELL_DUAL_CODECS, + ALC287_FIXUP_TAS2781_I2C_2, + ALC287_FIXUP_TAS2781_I2C_4 }; /* A special fixup for Lenovo C940 and Yoga Duet 7; @@ -9189,6 +9250,18 @@ static const struct hda_fixup alc269_fixups[] = { .chained = true, .chain_id = ALC255_FIXUP_DELL1_MIC_NO_PRESENCE, }, + [ALC287_FIXUP_TAS2781_I2C_2] = { + .type = HDA_FIXUP_FUNC, + .v.func = tas2781_fixup_i2c, + .chained = true, + .chain_id = ALC269_FIXUP_THINKPAD_ACPI, + }, + [ALC287_FIXUP_TAS2781_I2C_4] = { + .type = HDA_FIXUP_FUNC, + .v.func = tas2781_fixup_i2c, + .chained = true, + .chain_id = ALC269_FIXUP_THINKPAD_ACPI, + }, }; static const struct snd_pci_quirk alc269_fixup_tbl[] = { @@ -9720,6 +9793,33 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x17aa, 0x3853, "Lenovo Yoga 7 15ITL5", ALC287_FIXUP_YOGA7_14ITL_SPEAKERS), SND_PCI_QUIRK(0x17aa, 0x3855, "Legion 7 16ITHG6", ALC287_FIXUP_LEGION_16ITHG6), SND_PCI_QUIRK(0x17aa, 0x3869, "Lenovo Yoga7 14IAL7", ALC287_FIXUP_YOGA9_14IAP7_BASS_SPK_PIN), + SND_PCI_QUIRK(0x17aa, 0x387d, "Yoga S780-16 pro Quad AAC", + ALC287_FIXUP_TAS2781_I2C_4), + SND_PCI_QUIRK(0x17aa, 0x387e, "Yoga S780-16 pro Quad YC", + ALC287_FIXUP_TAS2781_I2C_4), + SND_PCI_QUIRK(0x17aa, 0x3881, "YB9 dual powe mode2 YC", + ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x3884, "Y780 YG DUAL", + ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x3886, "Y780 VECO DUAL", + ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x38a7, "Y780P AMD YG dual", + ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x38a8, "Y780P AMD VECO dual", + ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x38ba, "Yoga S780-14.5 Air AMD quad YC", + ALC287_FIXUP_TAS2781_I2C_4), + SND_PCI_QUIRK(0x17aa, 0x38bb, "Yoga S780-14.5 Air AMD quad AAC", + ALC287_FIXUP_TAS2781_I2C_4), + SND_PCI_QUIRK(0x17aa, 0x38be, "Yoga S980-14.5 proX YC Dual", + ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x38bf, "Yoga S980-14.5 proX LX Dual", + ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x38c3, "Y980 DUAL", ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x38cb, "Y790 YG DUAL", + ALC287_FIXUP_TAS2781_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x38cd, "Y790 VECO DUAL", + ALC287_FIXUP_TAS2781_I2C_2), SND_PCI_QUIRK(0x17aa, 0x3902, "Lenovo E50-80", ALC269_FIXUP_DMIC_THINKPAD_ACPI), SND_PCI_QUIRK(0x17aa, 0x3977, "IdeaPad S210", ALC283_FIXUP_INT_MIC), SND_PCI_QUIRK(0x17aa, 0x3978, "Lenovo B50-70", ALC269_FIXUP_DMIC_THINKPAD_ACPI), diff --git a/sound/pci/hda/tas2781_hda_i2c.c b/sound/pci/hda/tas2781_hda_i2c.c new file mode 100644 index 000000000000..b519f7d3f5d6 --- /dev/null +++ b/sound/pci/hda/tas2781_hda_i2c.c @@ -0,0 +1,805 @@ +// SPDX-License-Identifier: GPL-2.0 +// +// TAS2781 HDA I2C driver +// +// Copyright 2023 Texas Instruments, Inc. +// +// Author: Shenghao Ding <shenghao-ding(a)ti.com> + +#include <linux/acpi.h> +#include <linux/crc8.h> +#include <linux/crc32.h> +#include <linux/efi.h> +#include <linux/firmware.h> +#include <linux/i2c.h> +#include <linux/mod_devicetable.h> +#include <linux/module.h> +#include <linux/pm_runtime.h> +#include <linux/regmap.h> +#include <sound/hda_codec.h> +#include <sound/soc.h> +#include <sound/tlv.h> +#include <sound/tas2781.h> + +#include "hda_local.h" +#include "hda_auto_parser.h" +#include "hda_component.h" +#include "hda_jack.h" +#include "hda_generic.h" + +#define TASDEVICE_SPEAKER_CALIBRATION_SIZE 20 + +#define ACARD_SINGLE_RANGE_EXT_TLV(xname, xreg, xshift, xmin, xmax, xinvert, \ + xhandler_get, xhandler_put, tlv_array) \ +{ .iface = SNDRV_CTL_ELEM_IFACE_CARD, .name = (xname),\ + .access = SNDRV_CTL_ELEM_ACCESS_TLV_READ |\ + SNDRV_CTL_ELEM_ACCESS_READWRITE,\ + .tlv.p = (tlv_array), \ + .info = snd_soc_info_volsw_range, \ + .get = xhandler_get, .put = xhandler_put, \ + .private_value = (unsigned long)&(struct soc_mixer_control) \ + {.reg = xreg, .rreg = xreg, .shift = xshift, \ + .rshift = xshift, .min = xmin, .max = xmax, \ + .invert = xinvert} } + +enum calib_data { + R0_VAL = 0, + INV_R0, + R0LOW, + POWER, + TLIM, + CALIB_MAX +}; + +static int tas2781_acpi_get_i2c_resource(struct acpi_resource + *ares, void *data) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)data; + struct acpi_resource_i2c_serialbus *sb; + + if (i2c_acpi_get_i2c_resource(ares, &sb)) { + if (sb->slave_address != TAS2781_GLOBAL_ADDR) { + tas_priv->tasdevice[tas_priv->ndev].dev_addr = + (unsigned int) sb->slave_address; + tas_priv->ndev++; + } else + tas_priv->glb_addr.dev_addr = TAS2781_GLOBAL_ADDR; + + } + + return 1; +} + +static int tas2781_hda_read_acpi(struct tasdevice_priv *tas_priv, + const char *hid) +{ + struct acpi_device *adev; + struct device *physdev; + LIST_HEAD(resources); + const char *sub; + int ret; + + adev = acpi_dev_get_first_match_dev(hid, NULL, -1); + if (!adev) { + dev_err(tas_priv->dev, + "Failed to find an ACPI device for %s\n", hid); + return -ENODEV; + } + strcpy(tas_priv->dev_name, hid); + physdev = get_device(acpi_get_first_physical_node(adev)); + acpi_dev_put(adev); + + sub = acpi_get_subsystem_id(ACPI_HANDLE(physdev)); + if (IS_ERR(sub)) + sub = NULL; + dev_info(tas_priv->dev, "subid = %s\n", sub); + + tas_priv->acpi_subsystem_id = sub; + + ret = acpi_dev_get_resources(adev, &resources, + tas2781_acpi_get_i2c_resource, tas_priv); + if (ret < 0) + goto err; + acpi_dev_free_resource_list(&resources); + + put_device(physdev); + dev_info(tas_priv->dev, "global addr: 0x%02x devcnt = %d\n", + tas_priv->glb_addr.dev_addr, tas_priv->ndev); + + return 0; + +err: + dev_err(tas_priv->dev, "Failed acpi ret: %d\n", ret); + put_device(physdev); + + return ret; +} + +static void tas2781_hda_playback_hook(struct device *dev, int action) +{ + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev); + int ret = 0; + + dev_info(tas_priv->dev, "%s: action = %d\n", __func__, action); + switch (action) { + case HDA_GEN_PCM_ACT_OPEN: + pm_runtime_get_sync(dev); + mutex_lock(&tas_priv->codec_lock); + tas_priv->cur_conf = 0; + tas_priv->rcabin.profile_cfg_id = 1; + tasdevice_tuning_switch(tas_priv, 0); + mutex_unlock(&tas_priv->codec_lock); + break; + case HDA_GEN_PCM_ACT_CLOSE: + mutex_lock(&tas_priv->codec_lock); + tasdevice_tuning_switch(tas_priv, 1); + mutex_unlock(&tas_priv->codec_lock); + + pm_runtime_mark_last_busy(dev); + pm_runtime_put_autosuspend(dev); + break; + default: + dev_warn(tas_priv->dev, "Playback action not supported: %d\n", + action); + break; + } + + if (ret) + dev_err(tas_priv->dev, "Regmap access fail: %d\n", ret); +} + +static int tasdevice_info_profile(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = 1; + uinfo->value.integer.min = 1; + uinfo->value.integer.max = max(0, tas_priv->rcabin.ncfgs); + + return 0; +} + +static int tasdevice_get_profile_id(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + + ucontrol->value.integer.value[0] = tas_priv->rcabin.profile_cfg_id; + + return 0; +} + +static int tasdevice_set_profile_id(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + + tas_priv->rcabin.profile_cfg_id = ucontrol->value.integer.value[0]; + + return 1; +} + +static int tasdevice_create_control(struct tasdevice_priv *tas_priv) +{ + char prof_ctrl_name[SNDRV_CTL_ELEM_ID_NAME_MAXLEN]; + struct hda_codec *codec = tas_priv->codec; + struct snd_kcontrol_new prof_ctrl = { + .name = prof_ctrl_name, + .iface = SNDRV_CTL_ELEM_IFACE_CARD, + .info = tasdevice_info_profile, + .get = tasdevice_get_profile_id, + .put = tasdevice_set_profile_id, + }; + int ret; + + /* Create a mixer item for selecting the active profile */ + scnprintf(prof_ctrl_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, + "tasdev-profile-id"); + ret = snd_ctl_add(codec->card, snd_ctl_new1(&prof_ctrl, tas_priv)); + if (ret) { + dev_err(tas_priv->dev, "Failed to add KControl %s = %d\n", + prof_ctrl.name, ret); + goto out; + } + + dev_dbg(tas_priv->dev, "Added Control %s\n", prof_ctrl.name); + +out: + return ret; +} + +static int tasdevice_info_programs(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + struct tasdevice_fw *tas_fw = tas_priv->fmw; + + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = 1; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = (int)tas_fw->nr_programs; + + return 0; +} + +static int tasdevice_info_configurations( + struct snd_kcontrol *kcontrol, struct snd_ctl_elem_info *uinfo) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + struct tasdevice_fw *tas_fw = tas_priv->fmw; + + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = 1; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = (int)tas_fw->nr_configurations - 1; + + return 0; +} + +static int tasdevice_program_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + + ucontrol->value.integer.value[0] = tas_priv->cur_prog; + + return 0; +} + +static int tasdevice_program_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + unsigned int nr_program = ucontrol->value.integer.value[0]; + + tas_priv->cur_prog = nr_program; + + return 1; +} + +static int tasdevice_config_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + + ucontrol->value.integer.value[0] = tas_priv->cur_conf; + + return 0; +} + +static int tasdevice_config_put( + struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + unsigned int nr_configuration = ucontrol->value.integer.value[0]; + + tas_priv->cur_conf = nr_configuration; + + return 1; +} + +/** + * tas2781_digital_getvol - get the volum control + * @kcontrol: control pointer + * @ucontrol: User data + * Customer Kcontrol for tas2781 is primarily for regmap booking, paging + * depends on internal regmap mechanism. + * tas2781 contains book and page two-level register map, especially + * book switching will set the register BXXP00R7F, after switching to the + * correct book, then leverage the mechanism for paging to access the + * register. + */ +static int tas2781_digital_getvol(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + + return tasdevice_digital_getvol(tas_priv, ucontrol, mc); +} + +static int tas2781_amp_getvol(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + + return tasdevice_amp_getvol(tas_priv, ucontrol, mc); +} + +static int tas2781_digital_putvol(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + + return tasdevice_digital_putvol(tas_priv, ucontrol, mc); +} + +static int tas2781_amp_putvol(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + + return tasdevice_amp_putvol(tas_priv, ucontrol, mc); +} + +static const struct snd_kcontrol_new tas2781_snd_controls[] = { + ACARD_SINGLE_RANGE_EXT_TLV("Amp Gain Volume", TAS2781_AMP_LEVEL, + 1, 0, 20, 0, tas2781_amp_getvol, + tas2781_amp_putvol, amp_vol_tlv), + ACARD_SINGLE_RANGE_EXT_TLV("Digital Volume", TAS2781_DVC_LVL, + 0, 0, 200, 1, tas2781_digital_getvol, + tas2781_digital_putvol, dvc_tlv), +}; + +static int tasdevice_dsp_create_ctrls(struct tasdevice_priv + *tas_priv) +{ + char prog_name[SNDRV_CTL_ELEM_ID_NAME_MAXLEN]; + char conf_name[SNDRV_CTL_ELEM_ID_NAME_MAXLEN]; + struct hda_codec *codec = tas_priv->codec; + struct snd_kcontrol_new prog_ctl = { + .name = prog_name, + .iface = SNDRV_CTL_ELEM_IFACE_CARD, + .info = tasdevice_info_programs, + .get = tasdevice_program_get, + .put = tasdevice_program_put, + }; + struct snd_kcontrol_new conf_ctl = { + .name = conf_name, + .iface = SNDRV_CTL_ELEM_IFACE_CARD, + .info = tasdevice_info_configurations, + .get = tasdevice_config_get, + .put = tasdevice_config_put, + }; + int ret; + + scnprintf(prog_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, "tasdev-prog-id"); + scnprintf(conf_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, "tasdev-conf-id"); + + ret = snd_ctl_add(codec->card, snd_ctl_new1(&prog_ctl, tas_priv)); + if (ret) { + dev_err(tas_priv->dev, "Failed to add KControl %s = %d\n", + prog_ctl.name, ret); + goto out; + } + + dev_dbg(tas_priv->dev, "Added Control %s\n", prog_ctl.name); + + ret = snd_ctl_add(codec->card, snd_ctl_new1(&conf_ctl, tas_priv)); + if (ret) { + dev_err(tas_priv->dev, "Failed to add KControl %s = %d\n", + conf_ctl.name, ret); + goto out; + } + + dev_dbg(tas_priv->dev, "Added Control %s\n", conf_ctl.name); +out: + return ret; +} + +static void tas2781_apply_calib(struct tasdevice_priv *tas_priv) +{ + unsigned char page_array[CALIB_MAX] = {0x17, 0x18, 0x18, 0x0d, 0x18}; + unsigned char rgno_array[CALIB_MAX] = {0x74, 0x0c, 0x14, 0x3c, 0x7c}; + unsigned char *data; + int i, j, rc; + + for (i = 0; i < tas_priv->ndev; i++) { + data = tas_priv->cali_data.data + + i * TASDEVICE_SPEAKER_CALIBRATION_SIZE; + for (j = 0; j < CALIB_MAX; j++) { + rc = tasdevice_dev_bulk_write(tas_priv, i, + TASDEVICE_REG(0, page_array[j], rgno_array[j]), + &(data[4 * j]), 4); + if (rc < 0) + dev_err(tas_priv->dev, + "chn %d calib %d bulk_wr err = %d\n", + i, j, rc); + } + } +} + +static int tas2781_save_calibration(struct tasdevice_priv *tas_priv) +{ + efi_guid_t efi_guid = EFI_GUID(0x02f9af02, 0x7734, 0x4233, 0xb4, 0x3d, + 0x93, 0xfe, 0x5a, 0xa3, 0x5d, 0xb3); + static efi_char16_t efi_name[] = L"CALI_DATA"; + struct hda_codec *codec = tas_priv->codec; + unsigned int subid = codec->core.subsystem_id & 0xFFFF; + struct tm *tm = &tas_priv->tm; + unsigned int attr, crc; + unsigned int *tmp_val; + efi_status_t status; + int ret = 0; + + //Lenovo devices + if ((subid == 0x387d) || (subid == 0x387e) || (subid == 0x3881) + || (subid == 0x3884) || (subid == 0x3886) || (subid == 0x38a7) + || (subid == 0x38a8) || (subid == 0x38ba) || (subid == 0x38bb) + || (subid == 0x38be) || (subid == 0x38bf) || (subid == 0x38c3) + || (subid == 0x38cb) || (subid == 0x38cd)) + efi_guid = EFI_GUID(0x1f52d2a1, 0xbb3a, 0x457d, 0xbc, 0x09, + 0x43, 0xa3, 0xf4, 0x31, 0x0a, 0x92); + tas_priv->cali_data.total_sz = 0; + /* Get real size of UEFI variable */ + status = efi.get_variable(efi_name, &efi_guid, &attr, + &tas_priv->cali_data.total_sz, tas_priv->cali_data.data); + if (status == EFI_BUFFER_TOO_SMALL) { + ret = -ENODEV; + /* Allocate data buffer of data_size bytes */ + tas_priv->cali_data.data = devm_kzalloc(tas_priv->dev, + tas_priv->cali_data.total_sz, GFP_KERNEL); + if (!tas_priv->cali_data.data) + return -ENOMEM; + /* Get variable contents into buffer */ + status = efi.get_variable(efi_name, &efi_guid, &attr, + &tas_priv->cali_data.total_sz, + tas_priv->cali_data.data); + if (status != EFI_SUCCESS) { + ret = -EINVAL; + goto out; + } + } + + tmp_val = (unsigned int *)tas_priv->cali_data.data; + + crc = crc32(~0, tas_priv->cali_data.data, 84) ^ ~0; + dev_info(tas_priv->dev, "cali crc 0x%08x PK tmp_val 0x%08x\n", + crc, tmp_val[21]); + + if (crc == tmp_val[21]) { + time64_to_tm(tmp_val[20], 0, tm); + dev_info(tas_priv->dev, "%4ld-%2d-%2d, %2d:%2d:%2d\n", + tm->tm_year, tm->tm_mon, tm->tm_mday, + tm->tm_hour, tm->tm_min, tm->tm_sec); + tas2781_apply_calib(tas_priv); + } +out: + return ret; +} + +static void tasdevice_fw_ready(const struct firmware *fmw, + void *context) +{ + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)context; + struct hda_codec *codec = tas_priv->codec; + int i, ret = 0; + + pm_runtime_get_sync(tas_priv->dev); + mutex_lock(&tas_priv->codec_lock); + + ret = tasdevice_rca_parser(tas_priv, fmw); + if (ret) + goto out; + tasdevice_create_control(tas_priv); + + for (i = 0; i < ARRAY_SIZE(tas2781_snd_controls); i++) { + ret = snd_ctl_add(codec->card, + snd_ctl_new1(&tas2781_snd_controls[i], tas_priv)); + if (ret) { + dev_err(tas_priv->dev, + "Failed to add KControl %s = %d\n", + tas2781_snd_controls[i].name, ret); + goto out; + } + } + + tasdevice_dsp_remove(tas_priv); + + tas_priv->fw_state = TASDEVICE_DSP_FW_PENDING; + scnprintf(tas_priv->coef_binaryname, 64, "TAS2XXX%04X.bin", + codec->core.subsystem_id & 0xffff); + ret = tasdevice_dsp_parser(tas_priv); + if (ret) { + dev_err(tas_priv->dev, "dspfw load %s error\n", + tas_priv->coef_binaryname); + tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL; + goto out; + } + tasdevice_dsp_create_ctrls(tas_priv); + + tas_priv->fw_state = TASDEVICE_DSP_FW_ALL_OK; + tasdevice_prmg_load(tas_priv, 0); + tas_priv->cur_prog = 0; + + /* If calibrated data occurs error, dsp will still works with default + * calibrated data inside algo. + */ + tas2781_save_calibration(tas_priv); + +out: + if (tas_priv->fw_state == TASDEVICE_DSP_FW_FAIL) { + /*If DSP FW fail, kcontrol won't be created */ + tasdevice_config_info_remove(tas_priv); + tasdevice_dsp_remove(tas_priv); + } + mutex_unlock(&tas_priv->codec_lock); + if (fmw) + release_firmware(fmw); + pm_runtime_mark_last_busy(tas_priv->dev); + pm_runtime_put_autosuspend(tas_priv->dev); +} + +static int tas2781_hda_bind(struct device *dev, struct device *master, + void *master_data) +{ + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev); + struct hda_component *comps = master_data; + int ret = 0; + + if (!comps || tas_priv->index < 0 || + tas_priv->index >= HDA_MAX_COMPONENTS) + return -EINVAL; + + comps = &comps[tas_priv->index]; + if (comps->dev) + return -EBUSY; + + pm_runtime_get_sync(dev); + + comps->dev = dev; + + strscpy(comps->name, dev_name(dev), sizeof(comps->name)); + + ret = tascodec_init(tas_priv, comps->codec, tasdevice_fw_ready); + + comps->playback_hook = tas2781_hda_playback_hook; + + pm_runtime_mark_last_busy(dev); + pm_runtime_put_autosuspend(dev); + + return ret; +} + +static void tas2781_hda_unbind(struct device *dev, + struct device *master, void *master_data) +{ + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev); + struct hda_component *comps = master_data; + + if (comps[tas_priv->index].dev == dev) + memset(&comps[tas_priv->index], 0, sizeof(*comps)); + + tasdevice_config_info_remove(tas_priv); + tasdevice_dsp_remove(tas_priv); + + tas_priv->fw_state = TASDEVICE_DSP_FW_PENDING; +} + +static const struct component_ops tas2781_hda_comp_ops = { + .bind = tas2781_hda_bind, + .unbind = tas2781_hda_unbind, +}; + +static void tas2781_hda_remove(struct device *dev) +{ + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev); + + pm_runtime_get_sync(tas_priv->dev); + pm_runtime_disable(tas_priv->dev); + + + component_del(tas_priv->dev, &tas2781_hda_comp_ops); + + pm_runtime_put_noidle(tas_priv->dev); + + tasdevice_remove(tas_priv); +} + +static int tas2781_hda_i2c_probe(struct i2c_client *clt) +{ + struct tasdevice_priv *tas_priv; + const char *device_name; + int ret; + + if (strstr(dev_name(&clt->dev), "TIAS2781")) + device_name = "TIAS2781"; + else + return -ENODEV; + + tas_priv = tasdevice_kzalloc(clt); + if (!tas_priv) + return -ENOMEM; + + tas_priv->irq_info.irq = clt->irq; + ret = tas2781_hda_read_acpi(tas_priv, device_name); + if (ret) + return dev_err_probe(tas_priv->dev, ret, + "Platform not supported\n"); + + ret = tasdevice_init(tas_priv); + if (ret) + goto err; + + pm_runtime_set_autosuspend_delay(tas_priv->dev, 3000); + pm_runtime_use_autosuspend(tas_priv->dev); + pm_runtime_mark_last_busy(tas_priv->dev); + pm_runtime_set_active(tas_priv->dev); + pm_runtime_get_noresume(tas_priv->dev); + pm_runtime_enable(tas_priv->dev); + + pm_runtime_put_autosuspend(tas_priv->dev); + + ret = component_add(tas_priv->dev, &tas2781_hda_comp_ops); + if (ret) { + dev_err(tas_priv->dev, "Register component failed: %d\n", ret); + pm_runtime_disable(tas_priv->dev); + } + +err: + if (ret) + tas2781_hda_remove(&clt->dev); + return ret; +} + +static void tas2781_hda_i2c_remove(struct i2c_client *clt) +{ + tas2781_hda_remove(&clt->dev); +} + +static int tas2781_runtime_suspend(struct device *dev) +{ + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev); + int i, ret = 0; + + dev_info(tas_priv->dev, "Runtime Suspend\n"); + + mutex_lock(&tas_priv->codec_lock); + + if (tas_priv->playback_started) { + tasdevice_tuning_switch(tas_priv, 1); + tas_priv->playback_started = false; + } + + tas_priv->cur_prog = -1; + tas_priv->cur_conf = -1; + + for (i = 0; i < tas_priv->ndev; i++) { + tas_priv->tasdevice[i].cur_book = -1; + tas_priv->tasdevice[i].cur_prog = -1; + tas_priv->tasdevice[i].cur_conf = -1; + } + + regcache_cache_only(tas_priv->regmap, true); + regcache_mark_dirty(tas_priv->regmap); + + mutex_unlock(&tas_priv->codec_lock); + + return ret; +} + +static int tas2781_runtime_resume(struct device *dev) +{ + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev); + unsigned long calib_data_sz = + tas_priv->ndev * TASDEVICE_SPEAKER_CALIBRATION_SIZE; + int ret = 0; + + dev_info(tas_priv->dev, "Runtime Resume\n"); + + mutex_lock(&tas_priv->codec_lock); + + regcache_cache_only(tas_priv->regmap, false); + ret = regcache_sync(tas_priv->regmap); + if (ret) { + dev_err(tas_priv->dev, + "Failed to restore register cache: %d\n", ret); + goto out; + } + + tasdevice_prmg_load(tas_priv, 0); + tas_priv->cur_prog = 0; + + /* If calibrated data occurs error, dsp will still works with default + * calibrated data inside algo. + */ + if (tas_priv->cali_data.total_sz > calib_data_sz) + tas2781_apply_calib(tas_priv); + +out: + mutex_unlock(&tas_priv->codec_lock); + + return ret; +} + +static int tas2781_system_suspend(struct device *dev) +{ + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev); + int ret; + + dev_info(tas_priv->dev, "System Suspend\n"); + + ret = pm_runtime_force_suspend(dev); + if (ret) + return ret; + + /* Shutdown chip before system suspend */ + regcache_cache_only(tas_priv->regmap, false); + tasdevice_tuning_switch(tas_priv, 1); + regcache_cache_only(tas_priv->regmap, true); + regcache_mark_dirty(tas_priv->regmap); + /* + * Reset GPIO may be shared, so cannot reset here. + * However beyond this point, amps may be powered down. + */ + return 0; +} + +static int tas2781_system_resume(struct device *dev) +{ + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev); + unsigned long calib_data_sz = + tas_priv->ndev * TASDEVICE_SPEAKER_CALIBRATION_SIZE; + int i, ret; + + dev_info(tas_priv->dev, "System Resume\n"); + + ret = pm_runtime_force_resume(dev); + + mutex_lock(&tas_priv->codec_lock); + tas_priv->cur_prog = -1; + tas_priv->cur_conf = -1; + + for (i = 0; i < tas_priv->ndev; i++) { + tas_priv->tasdevice[i].cur_book = -1; + tas_priv->tasdevice[i].cur_prog = -1; + tas_priv->tasdevice[i].cur_conf = -1; + } + tas2781_reset(tas_priv); + tasdevice_prmg_load(tas_priv, 0); + tas_priv->cur_prog = 0; + + /* If calibrated data occurs error, dsp will still works with default + * calibrated data inside algo. + */ + if (tas_priv->cali_data.total_sz > calib_data_sz) + tas2781_apply_calib(tas_priv); + mutex_unlock(&tas_priv->codec_lock); + + return ret; +} + +static const struct dev_pm_ops tas2781_hda_pm_ops = { + RUNTIME_PM_OPS(tas2781_runtime_suspend, tas2781_runtime_resume, + NULL) + SYSTEM_SLEEP_PM_OPS(tas2781_system_suspend, tas2781_system_resume) +}; + +static const struct i2c_device_id tas2781_hda_i2c_id[] = { + { "tas2781-hda", 0 }, + {} +}; + +static const struct acpi_device_id tas2781_acpi_hda_match[] = { + {"TIAS2781", 0 }, + {} +}; +MODULE_DEVICE_TABLE(acpi, tas2781_acpi_hda_match); + +static struct i2c_driver tas2781_hda_i2c_driver = { + .driver = { + .name = "tas2781-hda", + .acpi_match_table = tas2781_acpi_hda_match, + .pm = &tas2781_hda_pm_ops, + }, + .id_table = tas2781_hda_i2c_id, + .probe_new = tas2781_hda_i2c_probe, + .remove = tas2781_hda_i2c_remove, +}; +module_i2c_driver(tas2781_hda_i2c_driver); + +MODULE_DESCRIPTION("TAS2781 HDA Driver"); +MODULE_AUTHOR("Shenghao Ding, TI, <shenghao-ding(a)ti.com>"); +MODULE_LICENSE("GPL"); +MODULE_IMPORT_NS(FW_TASDEVICE); -- 2.34.1

1 0

[PATCH v1 1/5] ASoC: tas2781: Add Header file for tas2781 driver
by Shenghao Ding 02 May '23

02 May '23

Create Header file for tas2781 driver. Signed-off-by: Shenghao Ding <13916275206(a)139.com> --- Changes in v1: - Initial Changes to be committed: new file: include/sound/tas2781-dsp.h new file: include/sound/tas2781.h --- include/sound/tas2781-dsp.h | 189 ++++++++++++++++++++++++++++++++++++ include/sound/tas2781.h | 179 ++++++++++++++++++++++++++++++++++ 2 files changed, 368 insertions(+) create mode 100644 include/sound/tas2781-dsp.h create mode 100644 include/sound/tas2781.h diff --git a/include/sound/tas2781-dsp.h b/include/sound/tas2781-dsp.h new file mode 100644 index 000000000000..091c3ffade17 --- /dev/null +++ b/include/sound/tas2781-dsp.h @@ -0,0 +1,189 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +// +// ALSA SoC Texas Instruments TAS2781 Audio Smart Amplifier +// +// Copyright (C) 2022 - 2023 Texas Instruments Incorporated +// https://www.ti.com +// +// The TAS2781 driver implements a flexible and configurable +// algo coefficient setting for one, two, or even multiple +// TAS2781 chips. +// +// Author: Shenghao Ding <shenghao-ding(a)ti.com> +// Author: Kevin Lu <kevin-lu(a)ti.com> +// + +#ifndef __TASDEVICE_DSP_H__ +#define __TASDEVICE_DSP_H__ + +#define MAIN_ALL_DEVICES 0x0d +#define MAIN_DEVICE_A 0x01 +#define MAIN_DEVICE_B 0x08 +#define MAIN_DEVICE_C 0x10 +#define MAIN_DEVICE_D 0x14 +#define COEFF_DEVICE_A 0x03 +#define COEFF_DEVICE_B 0x0a +#define COEFF_DEVICE_C 0x11 +#define COEFF_DEVICE_D 0x15 +#define PRE_DEVICE_A 0x04 +#define PRE_DEVICE_B 0x0b +#define PRE_DEVICE_C 0x12 +#define PRE_DEVICE_D 0x16 + +#define PPC3_VERSION 0x4100 +#define RCA_CONFIGID_BYPASS_ALL 0 +#define TASDEVICE_DEVICE_SUM 8 +#define TASDEVICE_CONFIG_SUM 64 + +enum channel { + top_left_Chn, + top_right_chn, + bottom_left_Chn, + bottom_right_chn, + max_chn, +}; + +enum tasdevice_dsp_dev_idx { + TASDEVICE_DSP_TAS_2555 = 0, + TASDEVICE_DSP_TAS_2555_STEREO, + TASDEVICE_DSP_TAS_2557_MONO, + TASDEVICE_DSP_TAS_2557_DUAL_MONO, + TASDEVICE_DSP_TAS_2559, + TASDEVICE_DSP_TAS_2563, + TASDEVICE_DSP_TAS_2563_DUAL_MONO = 7, + TASDEVICE_DSP_TAS_2563_QUAD, + TASDEVICE_DSP_TAS_2563_21, + TASDEVICE_DSP_TAS_2781, + TASDEVICE_DSP_TAS_2781_DUAL_MONO, + TASDEVICE_DSP_TAS_2781_21, + TASDEVICE_DSP_TAS_2781_QUAD, + TASDEVICE_DSP_TAS_MAX_DEVICE +}; + +struct tasdevice_fw_fixed_hdr { + unsigned int fwsize; + unsigned int ppcver; + unsigned int drv_ver; +}; + +struct tasdevice_dspfw_hdr { + struct tasdevice_fw_fixed_hdr fixed_hdr; + unsigned short device_family; + unsigned short device; + unsigned char ndev; +}; + +struct tasdev_blk { + int nr_retry; + unsigned int type; + unsigned char is_pchksum_present; + unsigned char pchksum; + unsigned char is_ychksum_present; + unsigned char ychksum; + unsigned int nr_cmds; + unsigned int blk_size; + unsigned int nr_subblocks; + unsigned char *data; +}; + +struct tasdevice_data { + char name[64]; + unsigned int nr_blk; + struct tasdev_blk *dev_blks; +}; + +struct tasdevice_prog { + unsigned int prog_size; + struct tasdevice_data dev_data; +}; + +struct tasdevice_config { + unsigned int cfg_size; + char name[64]; + struct tasdevice_data dev_data; +}; + +struct tasdevice_calibration { + struct tasdevice_data dev_data; +}; + +struct tasdevice_fw { + struct tasdevice_dspfw_hdr fw_hdr; + unsigned short nr_programs; + struct tasdevice_prog *programs; + unsigned short nr_configurations; + struct tasdevice_config *configs; + unsigned short nr_calibrations; + struct tasdevice_calibration *calibrations; + struct device *dev; +}; + +enum tasdevice_dsp_fw_state { + TASDEVICE_DSP_FW_NONE = 0, + TASDEVICE_DSP_FW_PENDING, + TASDEVICE_DSP_FW_FAIL, + TASDEVICE_DSP_FW_ALL_OK, +}; + +enum tasdevice_bin_blk_type { + TASDEVICE_BIN_BLK_COEFF = 1, + TASDEVICE_BIN_BLK_POST_POWER_UP, + TASDEVICE_BIN_BLK_PRE_SHUTDOWN, + TASDEVICE_BIN_BLK_PRE_POWER_UP, + TASDEVICE_BIN_BLK_POST_SHUTDOWN +}; + +struct tasdevice_rca_hdr { + unsigned int img_sz; + unsigned int checksum; + unsigned int binary_version_num; + unsigned int drv_fw_version; + unsigned char plat_type; + unsigned char dev_family; + unsigned char reserve; + unsigned char ndev; + unsigned char devs[TASDEVICE_DEVICE_SUM]; + unsigned int nconfig; + unsigned int config_size[TASDEVICE_CONFIG_SUM]; +}; + +struct tasdev_blk_data { + unsigned char dev_idx; + unsigned char block_type; + unsigned short yram_checksum; + unsigned int block_size; + unsigned int n_subblks; + unsigned char *regdata; +}; + +struct tasdevice_config_info { + unsigned int nblocks; + unsigned int real_nblocks; + unsigned char active_dev; + struct tasdev_blk_data **blk_data; +}; + +struct tasdevice_rca { + struct tasdevice_rca_hdr fw_hdr; + int ncfgs; + struct tasdevice_config_info **cfg_info; + int profile_cfg_id; +}; + +void tasdevice_select_cfg_blk(void *context, int conf_no, + unsigned char block_type); +void tasdevice_config_info_remove(void *context); +void tasdevice_dsp_remove(void *context); +int tasdevice_dsp_parser(void *context); +int tasdevice_rca_parser(void *context, const struct firmware *fmw); +void tasdevice_dsp_remove(void *context); +void tasdevice_calbin_remove(void *context); +int tasdevice_select_tuningprm_cfg(void *context, int prm, + int cfg_no, int rca_conf_no); +int tasdevice_prmg_load(void *context, int prm_no); +int tasdevice_prmg_calibdata_load(void *context, int prm_no); +void tasdevice_tuning_switch(void *context, int state); +int tas2781_load_calibration(void *context, char *file_name, + enum channel i); + +#endif diff --git a/include/sound/tas2781.h b/include/sound/tas2781.h new file mode 100644 index 000000000000..7df637ad3be1 --- /dev/null +++ b/include/sound/tas2781.h @@ -0,0 +1,179 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +// +// ALSA SoC Texas Instruments TAS2781 Audio Smart Amplifier +// +// Copyright (C) 2022 - 2023 Texas Instruments Incorporated +// https://www.ti.com +// +// The TAS2781 driver implements a flexible and configurable +// algo coefficient setting for one, two, or even multiple +// TAS2781 chips. +// +// Author: Shenghao Ding <shenghao-ding(a)ti.com> +// Author: Kevin Lu <kevin-lu(a)ti.com> +// + +#ifndef __TAS2781_H__ +#define __TAS2781_H__ + +#include <linux/kernel.h> +#include "tas2781-dsp.h" + +/* version number */ +#define TAS2781_DRV_VER 1 +#define SMARTAMP_MODULE_NAME "tas2781" +#define TAS2781_GLOBAL_ADDR 0x40 +#define TASDEVICE_RATES (SNDRV_PCM_RATE_44100 |\ + SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_96000 |\ + SNDRV_PCM_RATE_88200) +#define TASDEVICE_MAX_CHANNELS 8 + +#define TASDEVICE_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | \ + SNDRV_PCM_FMTBIT_S24_LE | \ + SNDRV_PCM_FMTBIT_S32_LE) + +/*PAGE Control Register (available in page0 of each book) */ +#define TASDEVICE_PAGE_SELECT 0x00 +#define TASDEVICE_BOOKCTL_PAGE 0x00 +#define TASDEVICE_BOOKCTL_REG 127 +#define TASDEVICE_BOOK_ID(reg) (reg / (256 * 128)) +#define TASDEVICE_PAGE_ID(reg) ((reg % (256 * 128)) / 128) +#define TASDEVICE_PAGE_REG(reg) ((reg % (256 * 128)) % 128) +#define TASDEVICE_PGRG(reg) (reg % (256 * 128)) +#define TASDEVICE_REG(book, page, reg) (((book * 256 * 128) + \ + (page * 128)) + reg) + +/*Software Reset */ +#define TAS2781_REG_SWRESET TASDEVICE_REG(0x0, 0X0, 0x02) +#define TAS2781_REG_SWRESET_RESET BIT(0) + +/* Enable Global addresses */ +#define TAS2781_MISC_CFG2 TASDEVICE_REG(0x0, 0X0, 0x07) +#define TAS2781_GLOBAL_ADDR_MASK BIT(1) +#define TAS2781_GLOBAL_ADDR_ENABLE BIT(1) + +/*I2C Checksum */ +#define TASDEVICE_I2CChecksum TASDEVICE_REG(0x0, 0x0, 0x7E) + +/* Volume control */ +#define TAS2781_DVC_LVL TASDEVICE_REG(0x0, 0x0, 0x1A) +#define TAS2781_AMP_LEVEL TASDEVICE_REG(0x0, 0x0, 0x03) +#define TAS2781_AMP_LEVEL_MASK GENMASK(5, 1) + +#define TASDEVICE_CMD_SING_W 0x1 +#define TASDEVICE_CMD_BURST 0x2 +#define TASDEVICE_CMD_DELAY 0x3 +#define TASDEVICE_CMD_FIELD_W 0x4 + +enum audio_device { + TAS2781 = 0, +}; + +struct tasdevice { + struct tasdevice_fw *cali_data_fmw; + unsigned int dev_addr; + unsigned int err_code; + unsigned char cur_book; + short cur_prog; + short cur_conf; + bool is_loading; + bool is_loaderr; +}; + +/* + * This item is used to store the generic i2c address of + * all the tas2781 devices for I2C broadcast during the multi-device + * writes, useless in mono case. + */ +struct global_addr { + int ref_cnt; + unsigned int dev_addr; + unsigned char cur_book; +}; + +struct tasdevice_irqinfo { + int irq_gpio; + int irq; +}; + +struct calidata { + unsigned char *data; + unsigned long total_sz; +}; + +struct tasdevice_priv { + struct tasdevice tasdevice[max_chn]; + struct tasdevice_irqinfo irq_info; + struct global_addr glb_addr; + struct tasdevice_rca rcabin; + struct tasdevice_fw *fmw; + struct regmap *regmap; + struct mutex codec_lock; + struct calidata cali_data; + struct gpio_desc *reset; + struct device *dev; + struct tm tm; + + unsigned char crc8_lkp_tbl[CRC8_TABLE_SIZE]; + unsigned char cal_binaryname[max_chn][64]; + unsigned char coef_binaryname[64]; + unsigned char rca_binaryname[64]; + unsigned char dev_name[32]; + unsigned char ndev; + unsigned int magic_num; + unsigned int chip_id; + unsigned int sysclk; + const char *acpi_subsystem_id; + int index; + int cur_prog; + int cur_conf; + int fw_state; + void *client; + void *codec; + bool isacpi; + bool playback_started; + void (*set_global_mode)(struct tasdevice_priv *tas_priv); + int (*fw_parse_variable_header)(struct tasdevice_priv *tas_priv, + const struct firmware *fmw, int offset); + int (*fw_parse_program_data)(struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, + const struct firmware *fmw, int offset); + int (*fw_parse_configuration_data)(struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, + const struct firmware *fmw, int offset); + int (*tasdevice_load_block)(struct tasdevice_priv *tas_priv, + struct tasdev_blk *block); +}; + +const DECLARE_TLV_DB_SCALE(dvc_tlv, -10000, 100, 0); +const DECLARE_TLV_DB_SCALE(amp_vol_tlv, 1100, 50, 0); + +void tas2781_reset(struct tasdevice_priv *tas_dev); +int tascodec_init(struct tasdevice_priv *tas_priv, void *codec, + void (*cont)(const struct firmware *fw, void *context)); +struct tasdevice_priv *tasdevice_kzalloc(struct i2c_client *i2c); +int tasdevice_init(struct tasdevice_priv *tas_priv); +void tasdevice_remove(struct tasdevice_priv *tas_priv); +int tasdevice_dev_read(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned int *value); +int tasdevice_dev_write(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned int value); +int tasdevice_dev_bulk_write( + struct tasdevice_priv *tas_priv, enum channel chn, + unsigned int reg, unsigned char *p_data, unsigned int n_length); +int tasdevice_dev_bulk_read(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned char *p_data, + unsigned int n_length); +int tasdevice_dev_update_bits( + struct tasdevice_priv *tasdevice, enum channel chn, + unsigned int reg, unsigned int mask, unsigned int value); +int tasdevice_amp_putvol(struct tasdevice_priv *tas_priv, + struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc); +int tasdevice_amp_getvol(struct tasdevice_priv *tas_priv, + struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc); +int tasdevice_digital_putvol(struct tasdevice_priv *tas_priv, + struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc); +int tasdevice_digital_getvol(struct tasdevice_priv *tas_priv, + struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc); + +#endif /* __TAS2781_H__ */ -- 2.34.1

1 0

[PATCH] ACP6x audio: Add board quirk for ASUSTeK COMPUTER INC. M3402RA
by István Váradi 01 May '23

01 May '23

Dear Linux Kernel Developers, I hope this email finds you well. I am writing to submit a patch for the ACP6x audio driver in the Linux kernel that adds a board quirk for the ASUSTeK COMPUTER INC. M3402RA. After experiencing issues with this board on my Linux system, I researched the issue and found that adding the following code snippet to the file sound/soc/amd/yc/acp6x-mach.c should resolve the issue: { .driver_data = &acp6x_card, .matches = { DMI_MATCH(DMI_BOARD_VENDOR, "ASUSTeK COMPUTER INC."), DMI_MATCH(DMI_PRODUCT_NAME, "M3402RA") } } As someone with no experience with the Linux kernel, I am submitting this patch in the hopes that it will be beneficial to a larger number of users. I have tested this patch on my own system and can confirm that it resolves the issue. Please let me know if you have any questions or require any additional information. Thank you for your hard work and dedication to improving the Linux kernel. Best regards, Steve Váradi

1 0

[PATCH] ACP6x audio: Add board quirk for ASUSTeK COMPUTER INC. M3402RA
by István Váradi 01 May '23

01 May '23

Dear Linux Kernel Developers, I hope this email finds you well. I am writing to submit a patch for the ACP6x audio driver in the Linux kernel that adds a board quirk for the ASUSTeK COMPUTER INC. M3402RA. After experiencing issues with this board on my Linux system, I researched the issue and found that adding the following code snippet to the file sound/soc/amd/yc/acp6x-mach.c should resolve the issue: { .driver_data = &acp6x_card, .matches = { DMI_MATCH(DMI_BOARD_VENDOR, "ASUSTeK COMPUTER INC."), DMI_MATCH(DMI_PRODUCT_NAME, "M3402RA") } } As someone with no experience with the Linux kernel, I am submitting this patch in the hopes that it will be beneficial to a larger number of users. I have tested this patch on my own system and can confirm that it resolves the issue. Please let me know if you have any questions or require any additional information. Thank you for your hard work and dedication to improving the Linux kernel. Best regards, Steve Váradi

1 0

Question regarding ALSA modules parameters
by Ivan Orlov 01 May '23

01 May '23

Hello! I have a question about the typical ALSA driver parameters, and maybe someone can answer me. Why it is necessary for ALSA module to have "index", "id" and "enable" parameters? They are mentioned as required in the "Writing an ALSA driver" and "Advanced Linux Sound Architecture - Driver Configuration guide" articles and used in many ALSA drivers, but for what purpose? Kind regards, Ivan Orlov.

2 2

[PATCH v1] ASoC: tas2781: Add tas2781 driver lib to support common operation for both ASoC codec driver and HDA codec driver
by Shenghao Ding 30 Apr '23

30 Apr '23

Create tas2781 driver lib. Signed-off-by: Shenghao Ding <13916275206(a)139.com> --- Changes in v1: - create driver lib Changes to be committed: new file: include/sound/tas2781-dsp.h new file: include/sound/tas2781.h modified: sound/soc/codecs/Kconfig modified: sound/soc/codecs/Makefile new file: sound/soc/codecs/tas2781-lib.c --- include/sound/tas2781-dsp.h | 187 ++++++++++++++ include/sound/tas2781.h | 168 ++++++++++++ sound/soc/codecs/Kconfig | 6 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/tas2781-lib.c | 455 +++++++++++++++++++++++++++++++++ 5 files changed, 818 insertions(+) create mode 100644 include/sound/tas2781-dsp.h create mode 100644 include/sound/tas2781.h create mode 100644 sound/soc/codecs/tas2781-lib.c diff --git a/include/sound/tas2781-dsp.h b/include/sound/tas2781-dsp.h new file mode 100644 index 000000000000..125cbba9298d --- /dev/null +++ b/include/sound/tas2781-dsp.h @@ -0,0 +1,187 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +// +// ALSA SoC Texas Instruments TAS2781 Audio Smart Amplifier +// +// Copyright (C) 2022 - 2023 Texas Instruments Incorporated +// https://www.ti.com +// +// The TAS2781 driver implements a flexible and configurable +// algo coefficient setting for one, two, or even multiple +// TAS2781 chips. +// +// Author: Shenghao Ding <shenghao-ding(a)ti.com> +// Author: Kevin Lu <kevin-lu(a)ti.com> +// + +#ifndef __TASDEVICE_DSP_H__ +#define __TASDEVICE_DSP_H__ + +#define MAIN_ALL_DEVICES 0x0d +#define MAIN_DEVICE_A 0x01 +#define MAIN_DEVICE_B 0x08 +#define MAIN_DEVICE_C 0x10 +#define MAIN_DEVICE_D 0x14 +#define COEFF_DEVICE_A 0x03 +#define COEFF_DEVICE_B 0x0a +#define COEFF_DEVICE_C 0x11 +#define COEFF_DEVICE_D 0x15 +#define PRE_DEVICE_A 0x04 +#define PRE_DEVICE_B 0x0b +#define PRE_DEVICE_C 0x12 +#define PRE_DEVICE_D 0x16 + +#define PPC3_VERSION 0x4100 +#define RCA_CONFIGID_BYPASS_ALL 0 +#define TASDEVICE_DEVICE_SUM 8 +#define TASDEVICE_CONFIG_SUM 64 + +enum channel { + top_left_Chn, + top_right_chn, + bottom_left_Chn, + bottom_right_chn, + max_chn, +}; + +enum tasdevice_dsp_dev_idx { + TASDEVICE_DSP_TAS_2555 = 0, + TASDEVICE_DSP_TAS_2555_STEREO, + TASDEVICE_DSP_TAS_2557_MONO, + TASDEVICE_DSP_TAS_2557_DUAL_MONO, + TASDEVICE_DSP_TAS_2559, + TASDEVICE_DSP_TAS_2563, + TASDEVICE_DSP_TAS_2563_DUAL_MONO = 7, + TASDEVICE_DSP_TAS_2563_QUAD, + TASDEVICE_DSP_TAS_2563_21, + TASDEVICE_DSP_TAS_2781, + TASDEVICE_DSP_TAS_2781_DUAL_MONO, + TASDEVICE_DSP_TAS_2781_21, + TASDEVICE_DSP_TAS_2781_QUAD, + TASDEVICE_DSP_TAS_MAX_DEVICE +}; + +struct tasdevice_fw_fixed_hdr { + unsigned int fwsize; + unsigned int ppcver; + unsigned int drv_ver; +}; + +struct tasdevice_dspfw_hdr { + struct tasdevice_fw_fixed_hdr fixed_hdr; + unsigned short device_family; + unsigned short device; + unsigned char ndev; +}; + +struct tasdev_blk { + int nr_retry; + unsigned int type; + unsigned char is_pchksum_present; + unsigned char pchksum; + unsigned char is_ychksum_present; + unsigned char ychksum; + unsigned int nr_cmds; + unsigned int blk_size; + unsigned int nr_subblocks; + unsigned char *data; +}; + +struct tasdevice_data { + char name[64]; + unsigned int nr_blk; + struct tasdev_blk *dev_blks; +}; + +struct tasdevice_prog { + unsigned int prog_size; + struct tasdevice_data dev_data; +}; + +struct tasdevice_config { + unsigned int cfg_size; + char name[64]; + struct tasdevice_data dev_data; +}; + +struct tasdevice_calibration { + struct tasdevice_data dev_data; +}; + +struct tasdevice_fw { + struct tasdevice_dspfw_hdr fw_hdr; + unsigned short nr_programs; + struct tasdevice_prog *programs; + unsigned short nr_configurations; + struct tasdevice_config *configs; + unsigned short nr_calibrations; + struct tasdevice_calibration *calibrations; + struct device *dev; +}; + +enum tasdevice_dsp_fw_state { + TASDEVICE_DSP_FW_NONE = 0, + TASDEVICE_DSP_FW_PENDING, + TASDEVICE_DSP_FW_FAIL, + TASDEVICE_DSP_FW_ALL_OK, +}; + +enum tasdevice_bin_blk_type { + TASDEVICE_BIN_BLK_COEFF = 1, + TASDEVICE_BIN_BLK_POST_POWER_UP, + TASDEVICE_BIN_BLK_PRE_SHUTDOWN, + TASDEVICE_BIN_BLK_PRE_POWER_UP, + TASDEVICE_BIN_BLK_POST_SHUTDOWN +}; + +struct tasdevice_rca_hdr { + unsigned int img_sz; + unsigned int checksum; + unsigned int binary_version_num; + unsigned int drv_fw_version; + unsigned char plat_type; + unsigned char dev_family; + unsigned char reserve; + unsigned char ndev; + unsigned char devs[TASDEVICE_DEVICE_SUM]; + unsigned int nconfig; + unsigned int config_size[TASDEVICE_CONFIG_SUM]; +}; + +struct tasdev_blk_data { + unsigned char dev_idx; + unsigned char block_type; + unsigned short yram_checksum; + unsigned int block_size; + unsigned int n_subblks; + unsigned char *regdata; +}; + +struct tasdevice_config_info { + unsigned int nblocks; + unsigned int real_nblocks; + unsigned char active_dev; + struct tasdev_blk_data **blk_data; +}; + +struct tasdevice_rca { + struct tasdevice_rca_hdr fw_hdr; + int ncfgs; + struct tasdevice_config_info **cfg_info; + int profile_cfg_id; +}; + +void tasdevice_select_cfg_blk(void *context, int conf_no, + unsigned char block_type); +void tasdevice_config_info_remove(void *context); +void tasdevice_dsp_remove(void *context); +int tasdevice_dsp_parser(void *context); +int tasdevice_rca_parser(void *context, const struct firmware *fmw); +void tasdevice_dsp_remove(void *context); +void tasdevice_calbin_remove(void *context); +int tasdevice_select_tuningprm_cfg(void *context, int prm, + int cfg_no, int rca_conf_no); +int tasdevice_prmg_load(void *context, int prm_no); +int tasdevice_prmg_calibdata_load(void *context, int prm_no); +void tasdevice_tuning_switch(void *context, int state); + +#endif diff --git a/include/sound/tas2781.h b/include/sound/tas2781.h new file mode 100644 index 000000000000..ee3dd56f2084 --- /dev/null +++ b/include/sound/tas2781.h @@ -0,0 +1,168 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +// +// ALSA SoC Texas Instruments TAS2781 Audio Smart Amplifier +// +// Copyright (C) 2022 - 2023 Texas Instruments Incorporated +// https://www.ti.com +// +// The TAS2781 driver implements a flexible and configurable +// algo coefficient setting for one, two, or even multiple +// TAS2781 chips. +// +// Author: Shenghao Ding <shenghao-ding(a)ti.com> +// Author: Kevin Lu <kevin-lu(a)ti.com> +// + +#ifndef __TAS2781_H__ +#define __TAS2781_H__ + +#include <linux/kernel.h> +#include "tas2781-dsp.h" + +/* version number */ +#define TAS2781_DRV_VER 1 +#define SMARTAMP_MODULE_NAME "tas2781" +#define TAS2781_GLOBAL_ADDR 0x40 +#define TASDEVICE_RATES (SNDRV_PCM_RATE_44100 |\ + SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_96000 |\ + SNDRV_PCM_RATE_88200) +#define TASDEVICE_MAX_CHANNELS 8 + +#define TASDEVICE_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | \ + SNDRV_PCM_FMTBIT_S24_LE | \ + SNDRV_PCM_FMTBIT_S32_LE) + +/*PAGE Control Register (available in page0 of each book) */ +#define TASDEVICE_PAGE_SELECT 0x00 +#define TASDEVICE_BOOKCTL_PAGE 0x00 +#define TASDEVICE_BOOKCTL_REG 127 +#define TASDEVICE_BOOK_ID(reg) (reg / (256 * 128)) +#define TASDEVICE_PAGE_ID(reg) ((reg % (256 * 128)) / 128) +#define TASDEVICE_PAGE_REG(reg) ((reg % (256 * 128)) % 128) +#define TASDEVICE_PGRG(reg) (reg % (256 * 128)) +#define TASDEVICE_REG(book, page, reg) (((book * 256 * 128) + \ + (page * 128)) + reg) + +/*Software Reset */ +#define TAS2781_REG_SWRESET TASDEVICE_REG(0x0, 0X0, 0x02) +#define TAS2781_REG_SWRESET_RESET BIT(0) + +/* Enable Global addresses */ +#define TAS2781_MISC_CFG2 TASDEVICE_REG(0x0, 0X0, 0x07) +#define TAS2781_GLOBAL_ADDR_MASK BIT(1) +#define TAS2781_GLOBAL_ADDR_ENABLE BIT(1) + +/*I2C Checksum */ +#define TASDEVICE_I2CChecksum TASDEVICE_REG(0x0, 0x0, 0x7E) + +/* Volume control */ +#define TAS2781_DVC_LVL TASDEVICE_REG(0x0, 0x0, 0x1A) +#define TAS2781_AMP_LEVEL TASDEVICE_REG(0x0, 0x0, 0x03) +#define TAS2781_AMP_LEVEL_MASK GENMASK(5, 1) + +#define TASDEVICE_CMD_SING_W 0x1 +#define TASDEVICE_CMD_BURST 0x2 +#define TASDEVICE_CMD_DELAY 0x3 +#define TASDEVICE_CMD_FIELD_W 0x4 + +enum audio_device { + TAS2781 = 0, +}; + +struct tasdevice { + struct tasdevice_fw *cali_data_fmw; + unsigned int dev_addr; + unsigned int err_code; + unsigned char cur_book; + short cur_prog; + short cur_conf; + bool is_loading; + bool is_loaderr; + bool is_calibrated_data_loaded; +}; + +/* + * This item is used to store the generic i2c address of + * all the tas2781 devices for I2C broadcast during the multi-device + * writes, useless in mono case. + */ +struct global_addr { + int ref_cnt; + unsigned int dev_addr; + unsigned char cur_book; +}; + +struct tasdevice_irqinfo { + int irq_gpio; + int irq; +}; + +struct calidata { + unsigned char *data; + unsigned long total_sz; +}; + +struct tasdevice_priv { + struct tasdevice tasdevice[max_chn]; + struct tasdevice_irqinfo irq_info; + struct global_addr glb_addr; + struct tasdevice_rca rcabin; + struct tasdevice_fw *fmw; + struct regmap *regmap; + struct mutex codec_lock; + struct calidata cali_data; + struct gpio_desc *reset; + struct device *dev; + struct tm tm; + + unsigned char crc8_lkp_tbl[CRC8_TABLE_SIZE]; + unsigned char cal_binaryname[max_chn][64]; + unsigned char coef_binaryname[64]; + unsigned char rca_binaryname[64]; + unsigned char dev_name[32]; + unsigned char ndev; + unsigned int magic_num; + unsigned int chip_id; + unsigned int sysclk; + const char *acpi_subsystem_id; + int index; + int cur_prog; + int cur_conf; + int fw_state; + void *client; + void *codec; + bool isacpi; + void (*set_global_mode)(struct tasdevice_priv *tas_priv); + int (*fw_parse_variable_header)(struct tasdevice_priv *tas_priv, + const struct firmware *fmw, int offset); + int (*fw_parse_program_data)(struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, + const struct firmware *fmw, int offset); + int (*fw_parse_configuration_data)(struct tasdevice_priv *tas_priv, + struct tasdevice_fw *tas_fmw, + const struct firmware *fmw, int offset); + int (*tasdevice_load_block)(struct tasdevice_priv *tas_priv, + struct tasdev_blk *block); +}; + +int tas2781_load_calibration(void *context, char *file_name, enum channel i); +int tascodec_init(struct tasdevice_priv *tas_priv, void *codec, + void (*cont)(const struct firmware *fw, void *context)); +struct tasdevice_priv *tasdevice_kzalloc(struct i2c_client *i2c); +int tasdevice_init(struct tasdevice_priv *tas_priv); +void tasdevice_remove(struct tasdevice_priv *tas_priv); +int tasdevice_dev_read(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned int *value); +int tasdevice_dev_write(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned int value); +int tasdevice_dev_bulk_write( + struct tasdevice_priv *tas_priv, enum channel chn, + unsigned int reg, unsigned char *p_data, unsigned int n_length); +int tasdevice_dev_bulk_read(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned char *p_data, + unsigned int n_length); +int tasdevice_dev_update_bits( + struct tasdevice_priv *tasdevice, enum channel chn, + unsigned int reg, unsigned int mask, unsigned int value); + +#endif /* __TAS2781_H__ */ diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 79d2362ad055..c899b18e423a 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -234,6 +234,7 @@ config SND_SOC_ALL_CODECS imply SND_SOC_TAS2764 imply SND_SOC_TAS2770 imply SND_SOC_TAS2780 + imply SND_SOC_TAS2781_LIB imply SND_SOC_TAS5086 imply SND_SOC_TAS571X imply SND_SOC_TAS5720 @@ -1699,6 +1700,11 @@ config SND_SOC_TAS2780 Enable support for Texas Instruments TAS2780 high-efficiency digital input mono Class-D audio power amplifiers. +config SND_SOC_TAS2781_LIB + select CRC8 + select REGMAP_I2C + tristate + config SND_SOC_TAS5086 tristate "Texas Instruments TAS5086 speaker amplifier" depends on I2C diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 5cdbae88e6e3..3f58a5df8120 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -269,6 +269,7 @@ snd-soc-tas5805m-objs := tas5805m.o snd-soc-tas6424-objs := tas6424.o snd-soc-tda7419-objs := tda7419.o snd-soc-tas2770-objs := tas2770.o +snd-soc-tas2781-lib-objs := tas2781-lib.o snd-soc-tfa9879-objs := tfa9879.o snd-soc-tfa989x-objs := tfa989x.o snd-soc-tlv320adc3xxx-objs := tlv320adc3xxx.o @@ -633,6 +634,7 @@ obj-$(CONFIG_SND_SOC_TAS2552) += snd-soc-tas2552.o obj-$(CONFIG_SND_SOC_TAS2562) += snd-soc-tas2562.o obj-$(CONFIG_SND_SOC_TAS2764) += snd-soc-tas2764.o obj-$(CONFIG_SND_SOC_TAS2780) += snd-soc-tas2780.o +obj-$(CONFIG_SND_SOC_TAS2781_LIB) += snd-soc-tas2781-lib.o obj-$(CONFIG_SND_SOC_TAS5086) += snd-soc-tas5086.o obj-$(CONFIG_SND_SOC_TAS571X) += snd-soc-tas571x.o obj-$(CONFIG_SND_SOC_TAS5720) += snd-soc-tas5720.o diff --git a/sound/soc/codecs/tas2781-lib.c b/sound/soc/codecs/tas2781-lib.c new file mode 100644 index 000000000000..1d843bc6c42e --- /dev/null +++ b/sound/soc/codecs/tas2781-lib.c @@ -0,0 +1,455 @@ +// SPDX-License-Identifier: GPL-2.0 +// +// tas2781-lib.c -- TAS2781 Common functions for HDA and ASoC Audio drivers +// +// Copyright 2023 Texas Instruments, Inc. +// +// Author: Shenghao Ding <shenghao-ding(a)ti.com> + +#include <linux/crc8.h> +#include <linux/firmware.h> +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_gpio.h> +#include <linux/of_irq.h> +#include <linux/regmap.h> +#include <linux/slab.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/tas2781.h> +#include <sound/tlv.h> + +#define TASDEVICE_CRC8_POLYNOMIAL 0x4d + +static const struct regmap_range_cfg tasdevice_ranges[] = { + { + .range_min = 0, + .range_max = 256 * 128, + .selector_reg = TASDEVICE_PAGE_SELECT, + .selector_mask = 0xff, + .selector_shift = 0, + .window_start = 0, + .window_len = 128, + }, +}; + +static const struct regmap_config tasdevice_regmap = { + .reg_bits = 16, + .val_bits = 8, + .cache_type = REGCACHE_RBTREE, + .ranges = tasdevice_ranges, + .num_ranges = ARRAY_SIZE(tasdevice_ranges), + .max_register = 256 * 128, +}; + +static int tasdevice_change_chn_book(struct tasdevice_priv *tas_priv, + enum channel chn, int book) +{ + struct i2c_client *client = (struct i2c_client *)tas_priv->client; + int ret = 0; + int i; + + if (chn < tas_priv->ndev) { + struct tasdevice *tasdev = &tas_priv->tasdevice[chn]; + + if (tas_priv->glb_addr.ref_cnt != 0) { + tas_priv->glb_addr.ref_cnt = 0; + tas_priv->glb_addr.cur_book = -1; + } + client->addr = tasdev->dev_addr; + if (tasdev->cur_book != book) { + ret = regmap_write(tas_priv->regmap, + TASDEVICE_BOOKCTL_REG, book); + if (ret < 0) { + dev_err(tas_priv->dev, "%s, E=%d\n", + __func__, ret); + goto out; + } + tasdev->cur_book = book; + } + } else if (chn == tas_priv->ndev) { + struct global_addr *glb_addr = &tas_priv->glb_addr; + + /* Chn == device number will enable global broadcast mode*/ + if (tas_priv->glb_addr.ref_cnt == 0) + for (i = 0; i < tas_priv->ndev; i++) + tas_priv->tasdevice[i].cur_book = -1; + client->addr = glb_addr->dev_addr; + if (glb_addr->cur_book != book) { + ret = regmap_write(tas_priv->regmap, + TASDEVICE_BOOKCTL_REG, book); + if (ret < 0) { + dev_err(tas_priv->dev, "%s, book%x, E=%d\n", + __func__, book, ret); + goto out; + } + glb_addr->cur_book = book; + } + + glb_addr->ref_cnt++; + } else { + ret = -EINVAL; + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + } + +out: + return ret; +} + +int tasdevice_dev_read(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned int *val) +{ + int ret = 0; + + if (chn < tas_priv->ndev) { + ret = tasdevice_change_chn_book(tas_priv, chn, + TASDEVICE_BOOK_ID(reg)); + if (ret < 0) + goto out; + + ret = regmap_read(tas_priv->regmap, TASDEVICE_PGRG(reg), val); + if (ret < 0) + dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret); + } else { + ret = -EINVAL; + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + } + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_dev_read); + +int tasdevice_dev_write(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned int value) +{ + int ret = 0; + + /* chn <= tas_dev->ndev will support global broadcast mode*/ + if (chn <= tas_priv->ndev) { + ret = tasdevice_change_chn_book(tas_priv, chn, + TASDEVICE_BOOK_ID(reg)); + if (ret < 0) + goto out; + + ret = regmap_write(tas_priv->regmap, TASDEVICE_PGRG(reg), + value); + if (ret < 0) + dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret); + } else { + ret = -EINVAL; + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + } + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_dev_write); + +int tasdevice_dev_bulk_write( + struct tasdevice_priv *tas_priv, enum channel chn, + unsigned int reg, unsigned char *data, + unsigned int len) +{ + int ret = 0; + + /* chn <= tas_dev->ndev will support global broadcast mode*/ + if (chn <= tas_priv->ndev) { + ret = tasdevice_change_chn_book(tas_priv, chn, + TASDEVICE_BOOK_ID(reg)); + if (ret < 0) + goto out; + + ret = regmap_bulk_write(tas_priv->regmap, TASDEVICE_PGRG(reg), + data, len); + if (ret < 0) + dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret); + } else { + ret = -EINVAL; + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + } + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_dev_bulk_write); + +int tasdevice_dev_bulk_read(struct tasdevice_priv *tas_priv, + enum channel chn, unsigned int reg, unsigned char *data, + unsigned int len) +{ + int ret = 0; + + if (chn < tas_priv->ndev) { + ret = tasdevice_change_chn_book(tas_priv, chn, + TASDEVICE_BOOK_ID(reg)); + if (ret < 0) + goto out; + + ret = regmap_bulk_read(tas_priv->regmap, TASDEVICE_PGRG(reg), + data, len); + if (ret < 0) + dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret); + } else + dev_err(tas_priv->dev, "%s, no such channel(%d)\n", __func__, + chn); + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_dev_bulk_read); + +int tasdevice_dev_update_bits( + struct tasdevice_priv *tasdev, enum channel chn, + unsigned int reg, unsigned int mask, unsigned int value) +{ + int ret = 0; + + /* update-bits can't support global broadcast mode, + * because this operation contains a reading operation + * for register value. In global mode, reading register + * from all of the tas2781 will cause confusion. + */ + if (chn < tasdev->ndev) { + ret = tasdevice_change_chn_book(tasdev, chn, + TASDEVICE_BOOK_ID(reg)); + if (ret < 0) + goto out; + + ret = regmap_update_bits(tasdev->regmap, + TASDEVICE_PGRG(reg), mask, value); + if (ret < 0) + dev_err(tasdev->dev, "%s, E=%d\n", __func__, ret); + } else { + dev_err(tasdev->dev, "%s, no such channel(%d)\n", __func__, + chn); + ret = -EINVAL; + } + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_dev_update_bits); + +/* Only register write and bulk write support global mode + * Other cases, such as bits update, register read and bulk + * only support device-by-device operation + */ +static void tas2781_set_global_mode(struct tasdevice_priv *tas_dev) +{ + int i, ret; + + for (i = 0; i < tas_dev->ndev; i++) { + ret = tasdevice_dev_update_bits(tas_dev, i, + TAS2781_MISC_CFG2, TAS2781_GLOBAL_ADDR_MASK, + TAS2781_GLOBAL_ADDR_ENABLE); + if (ret < 0) { + dev_err(tas_dev->dev, "%s: chn %d set glb fail, %d\n", + __func__, i, ret); + continue; + } + } +} + +struct tasdevice_priv *tasdevice_kzalloc(struct i2c_client *i2c) +{ + struct tasdevice_priv *tas_priv; + + tas_priv = devm_kzalloc(&i2c->dev, sizeof(*tas_priv), GFP_KERNEL); + if (!tas_priv) + return NULL; + tas_priv->dev = &i2c->dev; + tas_priv->client = (void *)i2c; + + return tas_priv; +} +EXPORT_SYMBOL_GPL(tasdevice_kzalloc); + +static void tas2781_reset(struct tasdevice_priv *tas_dev) +{ + int ret, i; + + if (tas_dev->reset) { + gpiod_set_value_cansleep(tas_dev->reset, 0); + usleep_range(500, 1000); + gpiod_set_value_cansleep(tas_dev->reset, 1); + } else { + for (i = 0; i < tas_dev->ndev; i++) { + ret = tasdevice_dev_write(tas_dev, i, + TAS2781_REG_SWRESET, + TAS2781_REG_SWRESET_RESET); + if (ret < 0) + dev_err(tas_dev->dev, + "dev %d swreset fail, %d\n", + i, ret); + } + } + usleep_range(1000, 1050); +} + +int tascodec_init(struct tasdevice_priv *tas_priv, void *codec, + void (*cont)(const struct firmware *fw, void *context)) +{ + int ret = 0; + + /* Codec Lock Hold to ensure that codec_probe and firmware parsing and + * loading do not simultaneously execute. + */ + mutex_lock(&tas_priv->codec_lock); + + scnprintf(tas_priv->rca_binaryname, 64, "%s_rca.bin", + tas_priv->dev_name); + crc8_populate_msb(tas_priv->crc8_lkp_tbl, TASDEVICE_CRC8_POLYNOMIAL); + tas_priv->codec = codec; + ret = request_firmware_nowait(THIS_MODULE, FW_ACTION_UEVENT, + tas_priv->rca_binaryname, tas_priv->dev, GFP_KERNEL, tas_priv, + cont); + if (ret) + dev_err(tas_priv->dev, "request_firmware_nowait err:0x%08x\n", + ret); + + tas2781_reset(tas_priv); + if (tas_priv->set_global_mode) + tas_priv->set_global_mode(tas_priv); + + /* Codec Lock Release*/ + mutex_unlock(&tas_priv->codec_lock); + return ret; +} +EXPORT_SYMBOL_GPL(tascodec_init); + +int tasdevice_init(struct tasdevice_priv *tas_priv) +{ + int ret = 0; + int i; + + tas_priv->regmap = devm_regmap_init_i2c(tas_priv->client, + &tasdevice_regmap); + if (IS_ERR(tas_priv->regmap)) { + ret = PTR_ERR(tas_priv->regmap); + dev_err(tas_priv->dev, "Failed to allocate register map: %d\n", + ret); + goto out; + } + + tas_priv->cur_prog = -1; + tas_priv->cur_conf = -1; + + for (i = 0; i < tas_priv->ndev; i++) { + tas_priv->tasdevice[i].cur_book = -1; + tas_priv->tasdevice[i].cur_prog = -1; + tas_priv->tasdevice[i].cur_conf = -1; + } + + if (tas_priv->glb_addr.dev_addr != 0 + && tas_priv->glb_addr.dev_addr < 0x7F) + tas_priv->set_global_mode = tas2781_set_global_mode; + dev_set_drvdata(tas_priv->dev, tas_priv); + + mutex_init(&tas_priv->codec_lock); + +out: + return ret; +} +EXPORT_SYMBOL_GPL(tasdevice_init); + +static void tasdev_dsp_prog_blk_remove(struct tasdevice_prog *prog) +{ + struct tasdevice_data *im; + struct tasdev_blk *blk; + unsigned int nr_blk; + + if (!prog) + return; + + im = &(prog->dev_data); + + if (!im->dev_blks) + return; + + for (nr_blk = 0; nr_blk < im->nr_blk; nr_blk++) { + blk = &(im->dev_blks[nr_blk]); + kfree(blk->data); + } + kfree(im->dev_blks); +} + +static void tasdev_dsp_prog_remove(struct tasdevice_prog *prog, + unsigned short nr) +{ + int i; + + for (i = 0; i < nr; i++) + tasdev_dsp_prog_blk_remove(&prog[i]); + kfree(prog); +} + +static void tasdev_dsp_cfg_blk_remove(struct tasdevice_config *cfg) +{ + struct tasdevice_data *im; + struct tasdev_blk *blk; + unsigned int nr_blk; + + if (cfg) { + im = &(cfg->dev_data); + + if (!im->dev_blks) + return; + + for (nr_blk = 0; nr_blk < im->nr_blk; nr_blk++) { + blk = &(im->dev_blks[nr_blk]); + kfree(blk->data); + } + kfree(im->dev_blks); + } +} + +static void tasdev_dsp_cfg_remove(struct tasdevice_config *config, + unsigned short nr) +{ + int i; + + for (i = 0; i < nr; i++) + tasdev_dsp_cfg_blk_remove(&config[i]); + kfree(config); +} + +void tasdevice_dsp_remove(void *context) +{ + struct tasdevice_priv *tas_dev = (struct tasdevice_priv *) context; + struct tasdevice_fw *tas_fmw = tas_dev->fmw; + + if (!tas_dev->fmw) + return; + + if (tas_fmw->programs) + tasdev_dsp_prog_remove(tas_fmw->programs, + tas_fmw->nr_programs); + if (tas_fmw->configs) + tasdev_dsp_cfg_remove(tas_fmw->configs, + tas_fmw->nr_configurations); + kfree(tas_fmw); + tas_dev->fmw = NULL; +} +EXPORT_SYMBOL_GPL(tasdevice_dsp_remove); + +void tasdevice_remove(struct tasdevice_priv *tas_priv) +{ + if (gpio_is_valid(tas_priv->irq_info.irq_gpio)) + gpio_free(tas_priv->irq_info.irq_gpio); + kfree(tas_priv->acpi_subsystem_id); + mutex_destroy(&tas_priv->codec_lock); +} +EXPORT_SYMBOL_GPL(tasdevice_remove); + +MODULE_DESCRIPTION("TAS2781 library"); +MODULE_AUTHOR("Shenghao Ding, TI, <shenghao-ding(a)ti.com>"); +MODULE_LICENSE("GPL"); -- 2.34.1

2 1

[PATCH v2] ASoC: fsl MPC52xx drivers require PPC_BESTCOMM
by Randy Dunlap 29 Apr '23

29 Apr '23

Both SND_MPC52xx_SOC_PCM030 and SND_MPC52xx_SOC_EFIKA select SND_SOC_MPC5200_AC97. The latter symbol depends on PPC_BESTCOMM, so the 2 former symbols should also depend on PPC_BESTCOMM since "select" does not follow any dependency chains. This prevents a kconfig warning and build errors: WARNING: unmet direct dependencies detected for SND_SOC_MPC5200_AC97 Depends on [n]: SOUND [=y] && !UML && SND [=m] && SND_SOC [=m] && SND_POWERPC_SOC [=m] && PPC_MPC52xx [=y] && PPC_BESTCOMM [=n] Selected by [m]: - SND_MPC52xx_SOC_PCM030 [=m] && SOUND [=y] && !UML && SND [=m] && SND_SOC [=m] && SND_POWERPC_SOC [=m] && PPC_MPC5200_SIMPLE [=y] - SND_MPC52xx_SOC_EFIKA [=m] && SOUND [=y] && !UML && SND [=m] && SND_SOC [=m] && SND_POWERPC_SOC [=m] && PPC_EFIKA [=y] ERROR: modpost: "mpc5200_audio_dma_destroy" [sound/soc/fsl/mpc5200_psc_ac97.ko] undefined! ERROR: modpost: "mpc5200_audio_dma_create" [sound/soc/fsl/mpc5200_psc_ac97.ko] undefined! Fixes: 40d9ec14e7e1 ("ASoC: remove BROKEN from Efika and pcm030 fabric drivers") Signed-off-by: Randy Dunlap <rdunlap(a)infradead.org> Cc: Grant Likely <grant.likely(a)secretlab.ca> Cc: Mark Brown <broonie(a)kernel.org> Cc: Liam Girdwood <lgirdwood(a)gmail.com> Cc: Shengjiu Wang <shengjiu.wang(a)gmail.com> Cc: Xiubo Li <Xiubo.Lee(a)gmail.com> Cc: alsa-devel(a)alsa-project.org Cc: linuxppc-dev(a)lists.ozlabs.org Cc: Jaroslav Kysela <perex(a)perex.cz> Cc: Takashi Iwai <tiwai(a)suse.com> --- v2: use correct email address for Mark Brown. sound/soc/fsl/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff -- a/sound/soc/fsl/Kconfig b/sound/soc/fsl/Kconfig --- a/sound/soc/fsl/Kconfig +++ b/sound/soc/fsl/Kconfig @@ -243,7 +243,7 @@ config SND_SOC_MPC5200_AC97 config SND_MPC52xx_SOC_PCM030 tristate "SoC AC97 Audio support for Phytec pcm030 and WM9712" - depends on PPC_MPC5200_SIMPLE + depends on PPC_MPC5200_SIMPLE && PPC_BESTCOMM select SND_SOC_MPC5200_AC97 select SND_SOC_WM9712 help @@ -252,7 +252,7 @@ config SND_MPC52xx_SOC_PCM030 config SND_MPC52xx_SOC_EFIKA tristate "SoC AC97 Audio support for bbplan Efika and STAC9766" - depends on PPC_EFIKA + depends on PPC_EFIKA && PPC_BESTCOMM select SND_SOC_MPC5200_AC97 select SND_SOC_STAC9766 help

1 0

[PATCH] ASoC: fsl MPC52xx drivers require PPC_BESTCOMM
by Randy Dunlap 29 Apr '23

29 Apr '23

Both SND_MPC52xx_SOC_PCM030 and SND_MPC52xx_SOC_EFIKA select SND_SOC_MPC5200_AC97. The latter symbol depends on PPC_BESTCOMM, so the 2 former symbols should also depend on PPC_BESTCOMM since "select" does not follow any dependency chains. This prevents a kconfig warning and build errors: WARNING: unmet direct dependencies detected for SND_SOC_MPC5200_AC97 Depends on [n]: SOUND [=y] && !UML && SND [=m] && SND_SOC [=m] && SND_POWERPC_SOC [=m] && PPC_MPC52xx [=y] && PPC_BESTCOMM [=n] Selected by [m]: - SND_MPC52xx_SOC_PCM030 [=m] && SOUND [=y] && !UML && SND [=m] && SND_SOC [=m] && SND_POWERPC_SOC [=m] && PPC_MPC5200_SIMPLE [=y] - SND_MPC52xx_SOC_EFIKA [=m] && SOUND [=y] && !UML && SND [=m] && SND_SOC [=m] && SND_POWERPC_SOC [=m] && PPC_EFIKA [=y] ERROR: modpost: "mpc5200_audio_dma_destroy" [sound/soc/fsl/mpc5200_psc_ac97.ko] undefined! ERROR: modpost: "mpc5200_audio_dma_create" [sound/soc/fsl/mpc5200_psc_ac97.ko] undefined! Fixes: 40d9ec14e7e1 ("ASoC: remove BROKEN from Efika and pcm030 fabric drivers") Signed-off-by: Randy Dunlap <rdunlap(a)infradead.org> Cc: Grant Likely <grant.likely(a)secretlab.ca> Cc: Mark Brown <broonie(a)opensource.wolfsonmicro.com> Cc: Liam Girdwood <lgirdwood(a)gmail.com> Cc: Shengjiu Wang <shengjiu.wang(a)gmail.com> Cc: Xiubo Li <Xiubo.Lee(a)gmail.com> Cc: alsa-devel(a)alsa-project.org Cc: linuxppc-dev(a)lists.ozlabs.org Cc: Jaroslav Kysela <perex(a)perex.cz> Cc: Takashi Iwai <tiwai(a)suse.com> --- sound/soc/fsl/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff -- a/sound/soc/fsl/Kconfig b/sound/soc/fsl/Kconfig --- a/sound/soc/fsl/Kconfig +++ b/sound/soc/fsl/Kconfig @@ -243,7 +243,7 @@ config SND_SOC_MPC5200_AC97 config SND_MPC52xx_SOC_PCM030 tristate "SoC AC97 Audio support for Phytec pcm030 and WM9712" - depends on PPC_MPC5200_SIMPLE + depends on PPC_MPC5200_SIMPLE && PPC_BESTCOMM select SND_SOC_MPC5200_AC97 select SND_SOC_WM9712 help @@ -252,7 +252,7 @@ config SND_MPC52xx_SOC_PCM030 config SND_MPC52xx_SOC_EFIKA tristate "SoC AC97 Audio support for bbplan Efika and STAC9766" - depends on PPC_EFIKA + depends on PPC_EFIKA && PPC_BESTCOMM select SND_SOC_MPC5200_AC97 select SND_SOC_STAC9766 help

1 0

Updated single and double quotes throughout
by GitHub pull_request - opened 29 Apr '23

29 Apr '23

alsa-project/alsa-utils pull request #208 was opened from wileyhy: Added double quotes to common expansions; removed quotes from strings; changed REQUIRES to an indexed array and changed the corresponding for loop; added curly braces where feasibly necessary; removed a few unnecessary trailing semi-colons; and put URL's in single quotes to prevent any possible expansions, except for within the sed command. Some logic structures depend on word splitting, so I left those as-is for this commit. Double exclamation marks in double quotes allow history expansion which is usually disabled in non-interactive shells, so I left those as-is also. Request URL : https://github.com/alsa-project/alsa-utils/pull/208 Patch URL : https://github.com/alsa-project/alsa-utils/pull/208.patch Repository URL: https://github.com/alsa-project/alsa-utils

1 0

reduce execs by four, and eliminate a logic bug
by GitHub pull_request - opened 29 Apr '23

29 Apr '23

alsa-project/alsa-utils pull request #207 was opened from wileyhy: Per `info uname`, uname always prints its data in the same order. Also, from [SC2015](https://www.shellcheck.net/wiki/SC2015), > "Note that A && B || C is not if-then-else. C may run when A is true." `set -x; read -r KERNEL_VERSION < <(uname -v); smp=x; [[ "$KERNEL_VERSION" = SMP ]] && { smp=y; readonly smp; false;} || smp=n; set -` Request URL : https://github.com/alsa-project/alsa-utils/pull/207 Patch URL : https://github.com/alsa-project/alsa-utils/pull/207.patch Repository URL: https://github.com/alsa-project/alsa-utils

1 0

Update `test` '-a' and '-o' to '&&' and '||'
by GitHub pull_request - opened 29 Apr '23

29 Apr '23

alsa-project/alsa-utils pull request #206 was opened from wileyhy: lines 50, 103: in two compound ['s, replace '-a' with '] && [' SC2166 – Prefer `[ p ] && [ q ]` as `[ p -a q ]` is not well defined. SC2107 – Instead of `[ a && b ]`, use `[ a ] && [ b ]`. line 45: in a compound test command, change '-o' to '|| test' SC1139 – Use `||` instead of `-o` between test commands. SC2109 – Instead of `[ a || b ]`, use `[ a ] || [ b ]`. https://www.shellcheck.net/wiki/SC[0-9]{4} Request URL : https://github.com/alsa-project/alsa-utils/pull/206 Patch URL : https://github.com/alsa-project/alsa-utils/pull/206.patch Repository URL: https://github.com/alsa-project/alsa-utils

1 0

reduce `exec`s by four, and eliminate logic bug
by GitHub pull_request - opened 29 Apr '23

29 Apr '23

alsa-project/alsa-utils pull request #205 was opened from wileyhy: Per `info uname,` `uname` always prints its data in the same order. Also, "note that A && B || C is not if-then-else. C may run when A is true." https://www.shellcheck.net/wiki/SC2015 set -x; read -r KERNEL_VERSION < <(uname -v); smp=x; [[ "$KERNEL_VERSION" = *SMP* ]] && { smp=y; readonly smp; false;} || smp=n; set - Request URL : https://github.com/alsa-project/alsa-utils/pull/205 Patch URL : https://github.com/alsa-project/alsa-utils/pull/205.patch Repository URL: https://github.com/alsa-project/alsa-utils

1 0

change '-o' in a `test` command to `|| test`
by GitHub pull_request - opened 29 Apr '23

29 Apr '23

alsa-project/alsa-utils pull request #204 was opened from wileyhy: this syntax functions locally Request URL : https://github.com/alsa-project/alsa-utils/pull/204 Patch URL : https://github.com/alsa-project/alsa-utils/pull/204.patch Repository URL: https://github.com/alsa-project/alsa-utils

1 0

Updated single and double quotes throughout
by GitHub pull_request - opened 29 Apr '23

29 Apr '23

alsa-project/alsa-utils pull request #203 was opened from wileyhy: Added double quotes to common expansions; removed quotes from strings; changed REQUIRES to an indexed array and changed the corresponding `for` loop; added curly braces where feasibly necessary; removed a few unnecessary trailing semi-colons; and put URL's in single quotes to prevent any possible expansions, except for within the `sed` command. Some logic structures depend on word splitting, so I left those as-is for this commit. Double exclamation marks in double quotes allow history expansion which is usually disabled in non-interactive shells, so I left those as-is also. Request URL : https://github.com/alsa-project/alsa-utils/pull/203 Patch URL : https://github.com/alsa-project/alsa-utils/pull/203.patch Repository URL: https://github.com/alsa-project/alsa-utils

1 0

in a compound `test` command, change '-o' to '||'
by GitHub pull_request - opened 29 Apr '23

29 Apr '23

alsa-project/alsa-utils pull request #202 was opened from wileyhy: Per a shellcheck warning https://www.shellcheck.net/wiki/SC1139 Request URL : https://github.com/alsa-project/alsa-utils/pull/202 Patch URL : https://github.com/alsa-project/alsa-utils/pull/202.patch Repository URL: https://github.com/alsa-project/alsa-utils

1 0

in two compound `[`'s, replace '-a' with '] && ['
by GitHub pull_request - opened 28 Apr '23

28 Apr '23

alsa-project/alsa-utils pull request #201 was opened from wileyhy: Per shellcheck warnings. https://www.shellcheck.net/wiki/SC2166 Request URL : https://github.com/alsa-project/alsa-utils/pull/201 Patch URL : https://github.com/alsa-project/alsa-utils/pull/201.patch Repository URL: https://github.com/alsa-project/alsa-utils

1 0

[PATCH] ASoC: amd: yc: Add ASUS M3402RA into DMI table
by Enrico Belleri 28 Apr '23

28 Apr '23

Fix builtin microphone on ASUS Vivobook S 14 OLED 2022 (M3402RA) Same issue with this model as apparently with other Rembrandt laptops: https://bugzilla.kernel.org/show_bug.cgi?id=216270 Signed-off-by: Enrico Belleri <kilgore.trout(a)idesmi.eu> --- sound/soc/amd/yc/acp6x-mach.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/sound/soc/amd/yc/acp6x-mach.c b/sound/soc/amd/yc/acp6x-mach.c index 4a69ce702360..80dfb6036859 100644 --- a/sound/soc/amd/yc/acp6x-mach.c +++ b/sound/soc/amd/yc/acp6x-mach.c @@ -213,6 +213,13 @@ static const struct dmi_system_id yc_acp_quirk_table[] = { DMI_MATCH(DMI_PRODUCT_NAME, "M5402RA"), } }, + { + .driver_data = &acp6x_card, + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, "ASUSTeK COMPUTER INC."), + DMI_MATCH(DMI_PRODUCT_NAME, "M3402RA"), + } + }, { .driver_data = &acp6x_card, .matches = { -- 2.40.0

2 1

[PATCH RESEND] ALSA: emu10k1: use more existing defines instead of open-coded numbers
by Oswald Buddenhagen 28 Apr '23

28 Apr '23

Using the *_MASK defines for "maximal value" is debatable. I got the idea from FreeBSD, and it sorta makes sense to me. Some hunks look a bit incomplete, because code that is going to be subsequently removed is not touched here. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- this failed to build previously due to a missed logical dependency on the "use high-level I/O functions also during init" patch. that patch was applied meanwhile, so it's now safe to apply this one as well. --- sound/pci/emu10k1/emu10k1_callback.c | 15 ++++----- sound/pci/emu10k1/emu10k1_main.c | 46 ++++++++++++++-------------- sound/pci/emu10k1/emufx.c | 6 ++-- sound/pci/emu10k1/emumixer.c | 8 ++--- sound/pci/emu10k1/emupcm.c | 12 ++++---- sound/pci/emu10k1/io.c | 18 +++++------ sound/pci/emu10k1/p16v.c | 29 ++++++++++-------- 7 files changed, 69 insertions(+), 65 deletions(-) diff --git a/sound/pci/emu10k1/emu10k1_callback.c b/sound/pci/emu10k1/emu10k1_callback.c index c6d152575181..9455df18f7b2 100644 --- a/sound/pci/emu10k1/emu10k1_callback.c +++ b/sound/pci/emu10k1/emu10k1_callback.c @@ -120,9 +120,9 @@ release_voice(struct snd_emux_voice *vp) struct snd_emu10k1 *hw; hw = vp->hw; - dcysusv = 0x8000 | (unsigned char)vp->reg.parm.modrelease; + dcysusv = (unsigned char)vp->reg.parm.modrelease | DCYSUSM_PHASE1_MASK; snd_emu10k1_ptr_write(hw, DCYSUSM, vp->ch, dcysusv); - dcysusv = 0x8000 | (unsigned char)vp->reg.parm.volrelease | DCYSUSV_CHANNELENABLE_MASK; + dcysusv = (unsigned char)vp->reg.parm.volrelease | DCYSUSV_PHASE1_MASK | DCYSUSV_CHANNELENABLE_MASK; snd_emu10k1_ptr_write(hw, DCYSUSV, vp->ch, dcysusv); } @@ -138,7 +138,8 @@ terminate_voice(struct snd_emux_voice *vp) if (snd_BUG_ON(!vp)) return; hw = vp->hw; - snd_emu10k1_ptr_write(hw, DCYSUSV, vp->ch, 0x807f | DCYSUSV_CHANNELENABLE_MASK); + snd_emu10k1_ptr_write(hw, DCYSUSV, vp->ch, + DCYSUSV_PHASE1_MASK | DCYSUSV_DECAYTIME_MASK | DCYSUSV_CHANNELENABLE_MASK); if (vp->block) { struct snd_emu10k1_memblk *emem; emem = (struct snd_emu10k1_memblk *)vp->block; @@ -347,9 +348,9 @@ start_voice(struct snd_emux_voice *vp) } /* channel to be silent and idle */ - snd_emu10k1_ptr_write(hw, DCYSUSV, ch, 0x0000); - snd_emu10k1_ptr_write(hw, VTFT, ch, 0x0000FFFF); - snd_emu10k1_ptr_write(hw, CVCF, ch, 0x0000FFFF); + snd_emu10k1_ptr_write(hw, DCYSUSV, ch, 0); + snd_emu10k1_ptr_write(hw, VTFT, ch, VTFT_FILTERTARGET_MASK); + snd_emu10k1_ptr_write(hw, CVCF, ch, CVCF_CURRENTFILTER_MASK); snd_emu10k1_ptr_write(hw, PTRX, ch, 0); snd_emu10k1_ptr_write(hw, CPF, ch, 0); @@ -453,7 +454,7 @@ start_voice(struct snd_emux_voice *vp) /* reset volume */ temp = (unsigned int)vp->vtarget << 16; snd_emu10k1_ptr_write(hw, VTFT, ch, temp | vp->ftarget); - snd_emu10k1_ptr_write(hw, CVCF, ch, temp | 0xff00); + snd_emu10k1_ptr_write(hw, CVCF, ch, temp | CVCF_CURRENTFILTER_MASK); return 0; } diff --git a/sound/pci/emu10k1/emu10k1_main.c b/sound/pci/emu10k1/emu10k1_main.c index 3abdaf1b9624..192208c291d6 100644 --- a/sound/pci/emu10k1/emu10k1_main.c +++ b/sound/pci/emu10k1/emu10k1_main.c @@ -59,8 +59,8 @@ void snd_emu10k1_voice_init(struct snd_emu10k1 *emu, int ch) { snd_emu10k1_ptr_write(emu, DCYSUSV, ch, 0); snd_emu10k1_ptr_write(emu, IP, ch, 0); - snd_emu10k1_ptr_write(emu, VTFT, ch, 0xffff); - snd_emu10k1_ptr_write(emu, CVCF, ch, 0xffff); + snd_emu10k1_ptr_write(emu, VTFT, ch, VTFT_FILTERTARGET_MASK); + snd_emu10k1_ptr_write(emu, CVCF, ch, CVCF_CURRENTFILTER_MASK); snd_emu10k1_ptr_write(emu, PTRX, ch, 0); snd_emu10k1_ptr_write(emu, CPF, ch, 0); snd_emu10k1_ptr_write(emu, CCR, ch, 0); @@ -74,7 +74,7 @@ void snd_emu10k1_voice_init(struct snd_emu10k1 *emu, int ch) snd_emu10k1_ptr_write(emu, ATKHLDM, ch, 0); snd_emu10k1_ptr_write(emu, DCYSUSM, ch, 0); - snd_emu10k1_ptr_write(emu, IFATN, ch, 0xffff); + snd_emu10k1_ptr_write(emu, IFATN, ch, IFATN_FILTERCUTOFF_MASK | IFATN_ATTENUATION_MASK); snd_emu10k1_ptr_write(emu, PEFE, ch, 0); snd_emu10k1_ptr_write(emu, FMMOD, ch, 0); snd_emu10k1_ptr_write(emu, TREMFRQ, ch, 24); /* 1 Hz */ @@ -90,10 +90,10 @@ void snd_emu10k1_voice_init(struct snd_emu10k1 *emu, int ch) /* Audigy extra stuffs */ if (emu->audigy) { - snd_emu10k1_ptr_write(emu, 0x4c, ch, 0); /* ?? */ - snd_emu10k1_ptr_write(emu, 0x4d, ch, 0); /* ?? */ - snd_emu10k1_ptr_write(emu, 0x4e, ch, 0); /* ?? */ - snd_emu10k1_ptr_write(emu, 0x4f, ch, 0); /* ?? */ + snd_emu10k1_ptr_write(emu, A_CSBA, ch, 0); + snd_emu10k1_ptr_write(emu, A_CSDC, ch, 0); + snd_emu10k1_ptr_write(emu, A_CSFE, ch, 0); + snd_emu10k1_ptr_write(emu, A_CSHG, ch, 0); snd_emu10k1_ptr_write(emu, A_FXRT1, ch, 0x03020100); snd_emu10k1_ptr_write(emu, A_FXRT2, ch, 0x3f3f3f3f); snd_emu10k1_ptr_write(emu, A_SENDAMOUNTS, ch, 0); @@ -259,7 +259,7 @@ static int snd_emu10k1_init(struct snd_emu10k1 *emu, int enable_ir) snd_emu10k1_ptr_write(emu, PTB, 0, emu->ptb_pages.addr); snd_emu10k1_ptr_write(emu, TCB, 0, 0); /* taken from original driver */ - snd_emu10k1_ptr_write(emu, TCBS, 0, 4); /* taken from original driver */ + snd_emu10k1_ptr_write(emu, TCBS, 0, TCBS_BUFFSIZE_256K); /* taken from original driver */ silent_page = (emu->silent_page.addr << emu->address_mode) | (emu->address_mode ? MAP_PTI_MASK1 : MAP_PTI_MASK0); for (ch = 0; ch < NUM_G; ch++) { @@ -818,7 +818,7 @@ static int snd_emu10k1_emu1010_init(struct snd_emu10k1 *emu) /* FPGA netlist already present so clear it */ /* Return to programming mode */ - snd_emu1010_fpga_write(emu, EMU_HANA_FPGA_CONFIG, 0x02); + snd_emu1010_fpga_write(emu, EMU_HANA_FPGA_CONFIG, EMU_HANA_FPGA_CONFIG_HANA); } snd_emu1010_fpga_read(emu, EMU_HANA_ID, &reg); dev_dbg(emu->card->dev, "reg2 = 0x%x\n", reg); @@ -858,36 +858,36 @@ static int snd_emu10k1_emu1010_init(struct snd_emu10k1 *emu) /* Optical -> ADAT I/O */ emu->emu1010.optical_in = 1; /* IN_ADAT */ emu->emu1010.optical_out = 1; /* OUT_ADAT */ - tmp = (emu->emu1010.optical_in ? EMU_HANA_OPTICAL_IN_ADAT : 0) | - (emu->emu1010.optical_out ? EMU_HANA_OPTICAL_OUT_ADAT : 0); + tmp = (emu->emu1010.optical_in ? EMU_HANA_OPTICAL_IN_ADAT : EMU_HANA_OPTICAL_IN_SPDIF) | + (emu->emu1010.optical_out ? EMU_HANA_OPTICAL_OUT_ADAT : EMU_HANA_OPTICAL_OUT_SPDIF); snd_emu1010_fpga_write(emu, EMU_HANA_OPTICAL_TYPE, tmp); /* Set no attenuation on Audio Dock pads. */ - snd_emu1010_fpga_write(emu, EMU_HANA_ADC_PADS, 0x00); emu->emu1010.adc_pads = 0x00; + snd_emu1010_fpga_write(emu, EMU_HANA_ADC_PADS, emu->emu1010.adc_pads); /* Unmute Audio dock DACs, Headphone source DAC-4. */ - snd_emu1010_fpga_write(emu, EMU_HANA_DOCK_MISC, 0x30); + snd_emu1010_fpga_write(emu, EMU_HANA_DOCK_MISC, EMU_HANA_DOCK_PHONES_192_DAC4); /* DAC PADs. */ - snd_emu1010_fpga_write(emu, EMU_HANA_DAC_PADS, 0x0f); - emu->emu1010.dac_pads = 0x0f; + emu->emu1010.dac_pads = EMU_HANA_DOCK_DAC_PAD1 | EMU_HANA_DOCK_DAC_PAD2 | + EMU_HANA_DOCK_DAC_PAD3 | EMU_HANA_DOCK_DAC_PAD4; + snd_emu1010_fpga_write(emu, EMU_HANA_DAC_PADS, emu->emu1010.dac_pads); /* SPDIF Format. Set Consumer mode, 24bit, copy enable */ - snd_emu1010_fpga_write(emu, EMU_HANA_SPDIF_MODE, 0x10); + snd_emu1010_fpga_write(emu, EMU_HANA_SPDIF_MODE, EMU_HANA_SPDIF_MODE_RX_INVALID); /* MIDI routing */ - snd_emu1010_fpga_write(emu, EMU_HANA_MIDI_IN, 0x19); - /* Unknown. */ - snd_emu1010_fpga_write(emu, EMU_HANA_MIDI_OUT, 0x0c); + snd_emu1010_fpga_write(emu, EMU_HANA_MIDI_IN, EMU_HANA_MIDI_INA_FROM_HAMOA | EMU_HANA_MIDI_INB_FROM_DOCK2); + snd_emu1010_fpga_write(emu, EMU_HANA_MIDI_OUT, EMU_HANA_MIDI_OUT_DOCK2 | EMU_HANA_MIDI_OUT_SYNC2); /* IRQ Enable: All on */ - /* snd_emu1010_fpga_write(emu, 0x09, 0x0f ); */ + /* snd_emu1010_fpga_write(emu, EMU_HANA_IRQ_ENABLE, 0x0f); */ /* IRQ Enable: All off */ snd_emu1010_fpga_write(emu, EMU_HANA_IRQ_ENABLE, 0x00); emu->emu1010.internal_clock = 1; /* 48000 */ /* Default WCLK set to 48kHz. */ - snd_emu1010_fpga_write(emu, EMU_HANA_DEFCLOCK, 0x00); + snd_emu1010_fpga_write(emu, EMU_HANA_DEFCLOCK, EMU_HANA_DEFCLOCK_48K); /* Word Clock source, Internal 48kHz x1 */ snd_emu1010_fpga_write(emu, EMU_HANA_WCLOCK, EMU_HANA_WCLOCK_INT_48K); /* snd_emu1010_fpga_write(emu, EMU_HANA_WCLOCK, EMU_HANA_WCLOCK_INT_48K | EMU_HANA_WCLOCK_4X); */ /* Audio Dock LEDs. */ - snd_emu1010_fpga_write(emu, EMU_HANA_DOCK_LEDS_2, 0x12); + snd_emu1010_fpga_write(emu, EMU_HANA_DOCK_LEDS_2, EMU_HANA_DOCK_LEDS_2_LOCK | EMU_HANA_DOCK_LEDS_2_48K); #if 0 /* For 96kHz */ @@ -1014,7 +1014,7 @@ static int snd_emu10k1_emu1010_init(struct snd_emu10k1 *emu) EMU_DST_ALICE_I2S2_LEFT, EMU_SRC_DOCK_ADC3_LEFT1); snd_emu1010_fpga_link_dst_src_write(emu, EMU_DST_ALICE_I2S2_RIGHT, EMU_SRC_DOCK_ADC3_RIGHT1); - snd_emu1010_fpga_write(emu, EMU_HANA_UNMUTE, 0x01); /* Unmute all */ + snd_emu1010_fpga_write(emu, EMU_HANA_UNMUTE, EMU_UNMUTE); #if 0 snd_emu1010_fpga_link_dst_src_write(emu, diff --git a/sound/pci/emu10k1/emufx.c b/sound/pci/emu10k1/emufx.c index db211a6e8a47..3f64ccab0e63 100644 --- a/sound/pci/emu10k1/emufx.c +++ b/sound/pci/emu10k1/emufx.c @@ -1355,7 +1355,7 @@ A_OP(icode, &ptr, iMAC0, A_GPR(var), A_GPR(var), A_GPR(vol), A_EXTIN(input)) gpr += 2; /* mic capture buffer */ - A_OP(icode, &ptr, iINTERP, A_EXTOUT(A_EXTOUT_MIC_CAP), A_EXTIN(A_EXTIN_AC97_L), 0xcd, A_EXTIN(A_EXTIN_AC97_R)); + A_OP(icode, &ptr, iINTERP, A_EXTOUT(A_EXTOUT_MIC_CAP), A_EXTIN(A_EXTIN_AC97_L), A_C_40000000, A_EXTIN(A_EXTIN_AC97_R)); /* Audigy CD Playback Volume */ A_ADD_VOLUME_IN(stereo_mix, gpr, A_EXTIN_SPDIF_CD_L); @@ -1438,7 +1438,7 @@ A_OP(icode, &ptr, iMAC0, A_GPR(var), A_GPR(var), A_GPR(vol), A_EXTIN(input)) /* Stereo Mix Center Playback */ /* Center = sub = Left/2 + Right/2 */ - A_OP(icode, &ptr, iINTERP, A_GPR(tmp), A_GPR(stereo_mix), 0xcd, A_GPR(stereo_mix+1)); + A_OP(icode, &ptr, iINTERP, A_GPR(tmp), A_GPR(stereo_mix), A_C_40000000, A_GPR(stereo_mix+1)); A_OP(icode, &ptr, iMAC0, A_GPR(playback+4), A_GPR(playback+4), A_GPR(gpr), A_GPR(tmp)); snd_emu10k1_init_mono_control(&controls[nctl++], "Center Playback Volume", gpr, 0); gpr++; @@ -2478,7 +2478,7 @@ int snd_emu10k1_fx8010_tram_setup(struct snd_emu10k1 *emu, u32 size) outl(HCFG_LOCKTANKCACHE_MASK | inl(emu->port + HCFG), emu->port + HCFG); spin_unlock_irq(&emu->emu_lock); snd_emu10k1_ptr_write(emu, TCB, 0, 0); - snd_emu10k1_ptr_write(emu, TCBS, 0, 0); + snd_emu10k1_ptr_write(emu, TCBS, 0, TCBS_BUFFSIZE_16K); if (emu->fx8010.etram_pages.area != NULL) { snd_dma_free_pages(&emu->fx8010.etram_pages); emu->fx8010.etram_pages.area = NULL; diff --git a/sound/pci/emu10k1/emumixer.c b/sound/pci/emu10k1/emumixer.c index 8fce3413f4ae..3ebc7c36a444 100644 --- a/sound/pci/emu10k1/emumixer.c +++ b/sound/pci/emu10k1/emumixer.c @@ -827,8 +827,8 @@ static int snd_emu1010_optical_out_put(struct snd_kcontrol *kcontrol, change = (emu->emu1010.optical_out != val); if (change) { emu->emu1010.optical_out = val; - tmp = (emu->emu1010.optical_in ? EMU_HANA_OPTICAL_IN_ADAT : 0) | - (emu->emu1010.optical_out ? EMU_HANA_OPTICAL_OUT_ADAT : 0); + tmp = (emu->emu1010.optical_in ? EMU_HANA_OPTICAL_IN_ADAT : EMU_HANA_OPTICAL_IN_SPDIF) | + (emu->emu1010.optical_out ? EMU_HANA_OPTICAL_OUT_ADAT : EMU_HANA_OPTICAL_OUT_SPDIF); snd_emu1010_fpga_write(emu, EMU_HANA_OPTICAL_TYPE, tmp); } return change; @@ -878,8 +878,8 @@ static int snd_emu1010_optical_in_put(struct snd_kcontrol *kcontrol, change = (emu->emu1010.optical_in != val); if (change) { emu->emu1010.optical_in = val; - tmp = (emu->emu1010.optical_in ? EMU_HANA_OPTICAL_IN_ADAT : 0) | - (emu->emu1010.optical_out ? EMU_HANA_OPTICAL_OUT_ADAT : 0); + tmp = (emu->emu1010.optical_in ? EMU_HANA_OPTICAL_IN_ADAT : EMU_HANA_OPTICAL_IN_SPDIF) | + (emu->emu1010.optical_out ? EMU_HANA_OPTICAL_OUT_ADAT : EMU_HANA_OPTICAL_OUT_SPDIF); snd_emu1010_fpga_write(emu, EMU_HANA_OPTICAL_TYPE, tmp); } return change; diff --git a/sound/pci/emu10k1/emupcm.c b/sound/pci/emu10k1/emupcm.c index b0c0ef342756..e8d2f0f6fbb3 100644 --- a/sound/pci/emu10k1/emupcm.c +++ b/sound/pci/emu10k1/emupcm.c @@ -352,8 +352,8 @@ static void snd_emu10k1_pcm_init_voice(struct snd_emu10k1 *emu, snd_emu10k1_ptr_write(emu, MAPA, voice, silent_page); snd_emu10k1_ptr_write(emu, MAPB, voice, silent_page); /* modulation envelope */ - snd_emu10k1_ptr_write(emu, CVCF, voice, 0xffff); - snd_emu10k1_ptr_write(emu, VTFT, voice, 0xffff); + snd_emu10k1_ptr_write(emu, VTFT, voice, VTFT_FILTERTARGET_MASK); + snd_emu10k1_ptr_write(emu, CVCF, voice, CVCF_CURRENTFILTER_MASK); snd_emu10k1_ptr_write(emu, ATKHLDM, voice, 0); snd_emu10k1_ptr_write(emu, DCYSUSM, voice, 0x007f); snd_emu10k1_ptr_write(emu, LFOVAL1, voice, 0x8000); @@ -621,8 +621,8 @@ static void snd_emu10k1_playback_prepare_voice(struct snd_emu10k1 *emu, struct s tmp = runtime->channels == 2 ? (master ? 1 : 2) : 0; vattn = mix != NULL ? (mix->attn[tmp] << 16) : 0; snd_emu10k1_ptr_write(emu, IFATN, voice, attn); - snd_emu10k1_ptr_write(emu, VTFT, voice, vattn | 0xffff); - snd_emu10k1_ptr_write(emu, CVCF, voice, vattn | 0xffff); + snd_emu10k1_ptr_write(emu, VTFT, voice, vattn | VTFT_FILTERTARGET_MASK); + snd_emu10k1_ptr_write(emu, CVCF, voice, vattn | CVCF_CURRENTFILTER_MASK); snd_emu10k1_ptr_write(emu, DCYSUSV, voice, 0x7f7f); snd_emu10k1_voice_clear_loop_stop(emu, voice); } @@ -663,8 +663,8 @@ static void snd_emu10k1_playback_stop_voice(struct snd_emu10k1 *emu, struct snd_ snd_emu10k1_ptr_write(emu, PTRX_PITCHTARGET, voice, 0); snd_emu10k1_ptr_write(emu, CPF_CURRENTPITCH, voice, 0); snd_emu10k1_ptr_write(emu, IFATN, voice, 0xffff); - snd_emu10k1_ptr_write(emu, VTFT, voice, 0xffff); - snd_emu10k1_ptr_write(emu, CVCF, voice, 0xffff); + snd_emu10k1_ptr_write(emu, VTFT, voice, VTFT_FILTERTARGET_MASK); + snd_emu10k1_ptr_write(emu, CVCF, voice, CVCF_CURRENTFILTER_MASK); snd_emu10k1_ptr_write(emu, IP, voice, 0); } diff --git a/sound/pci/emu10k1/io.c b/sound/pci/emu10k1/io.c index c60573f14ea8..cfb96a67aa35 100644 --- a/sound/pci/emu10k1/io.c +++ b/sound/pci/emu10k1/io.c @@ -95,8 +95,8 @@ unsigned int snd_emu10k1_ptr20_read(struct snd_emu10k1 * emu, regptr = (reg << 16) | chn; spin_lock_irqsave(&emu->emu_lock, flags); - outl(regptr, emu->port + 0x20 + PTR); - val = inl(emu->port + 0x20 + DATA); + outl(regptr, emu->port + PTR2); + val = inl(emu->port + DATA2); spin_unlock_irqrestore(&emu->emu_lock, flags); return val; } @@ -112,8 +112,8 @@ void snd_emu10k1_ptr20_write(struct snd_emu10k1 *emu, regptr = (reg << 16) | chn; spin_lock_irqsave(&emu->emu_lock, flags); - outl(regptr, emu->port + 0x20 + PTR); - outl(data, emu->port + 0x20 + DATA); + outl(regptr, emu->port + PTR2); + outl(data, emu->port + DATA2); spin_unlock_irqrestore(&emu->emu_lock, flags); } @@ -128,7 +128,7 @@ int snd_emu10k1_spi_write(struct snd_emu10k1 * emu, /* This function is not re-entrant, so protect against it. */ spin_lock(&emu->spi_lock); if (emu->card_capabilities->ca0108_chip) - reg = 0x3c; /* PTR20, reg 0x3c */ + reg = P17V_SPI; else { /* For other chip types the SPI register * is currently unknown. */ @@ -280,10 +280,10 @@ void snd_emu1010_fpga_link_dst_src_write(struct snd_emu10k1 *emu, u32 dst, u32 s return; if (snd_BUG_ON(src & ~0x71f)) return; - snd_emu1010_fpga_write(emu, 0x00, dst >> 8); - snd_emu1010_fpga_write(emu, 0x01, dst & 0x1f); - snd_emu1010_fpga_write(emu, 0x02, src >> 8); - snd_emu1010_fpga_write(emu, 0x03, src & 0x1f); + snd_emu1010_fpga_write(emu, EMU_HANA_DESTHI, dst >> 8); + snd_emu1010_fpga_write(emu, EMU_HANA_DESTLO, dst & 0x1f); + snd_emu1010_fpga_write(emu, EMU_HANA_SRCHI, src >> 8); + snd_emu1010_fpga_write(emu, EMU_HANA_SRCLO, src & 0x1f); } void snd_emu10k1_intr_enable(struct snd_emu10k1 *emu, unsigned int intrenb) diff --git a/sound/pci/emu10k1/p16v.c b/sound/pci/emu10k1/p16v.c index ce4d3450959c..e7f097cae574 100644 --- a/sound/pci/emu10k1/p16v.c +++ b/sound/pci/emu10k1/p16v.c @@ -254,19 +254,24 @@ static int snd_p16v_pcm_prepare_playback(struct snd_pcm_substream *substream) emu->p16v_buffer->bytes); #endif /* debug */ tmp = snd_emu10k1_ptr_read(emu, A_SPDIF_SAMPLERATE, channel); + tmp &= ~(A_SPDIF_RATE_MASK | A_EHC_SRC48_MASK); switch (runtime->rate) { case 44100: - snd_emu10k1_ptr_write(emu, A_SPDIF_SAMPLERATE, channel, (tmp & ~0xe0e0) | 0x8080); + snd_emu10k1_ptr_write(emu, A_SPDIF_SAMPLERATE, channel, + tmp | A_SPDIF_44100 | A_EHC_SRC48_44); break; case 96000: - snd_emu10k1_ptr_write(emu, A_SPDIF_SAMPLERATE, channel, (tmp & ~0xe0e0) | 0x4040); + snd_emu10k1_ptr_write(emu, A_SPDIF_SAMPLERATE, channel, + tmp | A_SPDIF_96000 | A_EHC_SRC48_96); break; case 192000: - snd_emu10k1_ptr_write(emu, A_SPDIF_SAMPLERATE, channel, (tmp & ~0xe0e0) | 0x2020); + snd_emu10k1_ptr_write(emu, A_SPDIF_SAMPLERATE, channel, + tmp | A_SPDIF_192000 | A_EHC_SRC48_192); break; case 48000: default: - snd_emu10k1_ptr_write(emu, A_SPDIF_SAMPLERATE, channel, (tmp & ~0xe0e0) | 0x0000); + snd_emu10k1_ptr_write(emu, A_SPDIF_SAMPLERATE, channel, + tmp | A_SPDIF_48000 | A_EHC_SRC48_BYPASS); break; } /* FIXME: Check emu->buffer.size before actually writing to it. */ @@ -282,46 +287,44 @@ static int snd_p16v_pcm_prepare_playback(struct snd_pcm_substream *substream) //snd_emu10k1_ptr20_write(emu, PLAYBACK_PERIOD_SIZE, channel, frames_to_bytes(runtime, runtime->period_size)<<16); // buffer size in bytes snd_emu10k1_ptr20_write(emu, PLAYBACK_PERIOD_SIZE, channel, 0); // buffer size in bytes snd_emu10k1_ptr20_write(emu, PLAYBACK_POINTER, channel, 0); - snd_emu10k1_ptr20_write(emu, 0x07, channel, 0x0); - snd_emu10k1_ptr20_write(emu, 0x08, channel, 0); + snd_emu10k1_ptr20_write(emu, PLAYBACK_FIFO_END_ADDRESS, channel, 0); + snd_emu10k1_ptr20_write(emu, PLAYBACK_FIFO_POINTER, channel, 0); return 0; } /* prepare capture callback */ static int snd_p16v_pcm_prepare_capture(struct snd_pcm_substream *substream) { struct snd_emu10k1 *emu = snd_pcm_substream_chip(substream); struct snd_pcm_runtime *runtime = substream->runtime; int channel = substream->pcm->device - emu->p16v_device_offset; - u32 tmp; /* dev_dbg(emu->card->dev, "prepare capture:channel_number=%d, rate=%d, " "format=0x%x, channels=%d, buffer_size=%ld, period_size=%ld, " "frames_to_bytes=%d\n", channel, runtime->rate, runtime->format, runtime->channels, runtime->buffer_size, runtime->period_size, frames_to_bytes(runtime, 1)); */ - tmp = snd_emu10k1_ptr_read(emu, A_SPDIF_SAMPLERATE, channel); switch (runtime->rate) { case 44100: - snd_emu10k1_ptr_write(emu, A_SPDIF_SAMPLERATE, channel, (tmp & ~0x0e00) | 0x0800); + snd_emu10k1_ptr_write(emu, A_I2S_CAPTURE_RATE, channel, A_I2S_CAPTURE_44100); break; case 96000: - snd_emu10k1_ptr_write(emu, A_SPDIF_SAMPLERATE, channel, (tmp & ~0x0e00) | 0x0400); + snd_emu10k1_ptr_write(emu, A_I2S_CAPTURE_RATE, channel, A_I2S_CAPTURE_96000); break; case 192000: - snd_emu10k1_ptr_write(emu, A_SPDIF_SAMPLERATE, channel, (tmp & ~0x0e00) | 0x0200); + snd_emu10k1_ptr_write(emu, A_I2S_CAPTURE_RATE, channel, A_I2S_CAPTURE_192000); break; case 48000: default: - snd_emu10k1_ptr_write(emu, A_SPDIF_SAMPLERATE, channel, (tmp & ~0x0e00) | 0x0000); + snd_emu10k1_ptr_write(emu, A_I2S_CAPTURE_RATE, channel, A_I2S_CAPTURE_48000); break; } /* FIXME: Check emu->buffer.size before actually writing to it. */ - snd_emu10k1_ptr20_write(emu, 0x13, channel, 0); + snd_emu10k1_ptr20_write(emu, CAPTURE_FIFO_POINTER, channel, 0); snd_emu10k1_ptr20_write(emu, CAPTURE_DMA_ADDR, channel, runtime->dma_addr); snd_emu10k1_ptr20_write(emu, CAPTURE_BUFFER_SIZE, channel, frames_to_bytes(runtime, runtime->buffer_size) << 16); // buffer size in bytes snd_emu10k1_ptr20_write(emu, CAPTURE_POINTER, channel, 0); -- 2.40.0.152.g15d061e6df

2 1

[PATCH v2 0/4] Add TDM audio on StarFive JH7110
by Walker Chen 28 Apr '23

28 Apr '23

This patchset adds TDM audio driver for the StarFive JH7110 SoC. The first patch adds device tree binding for TDM module. The second patch adds the item for JH7110 audio board to the dt-binding of StarFive SoC-based boards. The third patch adds tdm driver support for JH7110 SoC. The last patch adds device node of tdm and sound card to JH7110 dts. The series has been tested on the VisionFive 2 board by plugging the raspberry pie audio board. For more information of raspberry pie audio board, you can take a look at the following webpage: https://wiki.seeedstudio.com/ReSpeaker_2_Mics_Pi_HAT/ The last patch should be applied after the following patchset: https://lore.kernel.org/all/20230411135558.44282-1-xingyu.wu@starfivetech.c… Changes since v1: - Rebased on Linux 6.3-rc4. - Added the dts file dedicated to describe audio card. - Added the item for JH7110 audio board to the dt-binding of StarFive SoC-based boards. --- v1: https://lore.kernel.org/all/20230329153320.31390-1-walker.chen@starfivetech… Walker Chen (4): dt-bindings: sound: Add TDM for StarFive JH7110 dt-bindings: riscv: Add item for StarFive JH7110 audio board ASoC: starfive: Add JH7110 TDM driver riscv: dts: starfive: add tdm node and sound card .../devicetree/bindings/riscv/starfive.yaml | 1 + .../bindings/sound/starfive,jh7110-tdm.yaml | 98 +++ MAINTAINERS | 6 + arch/riscv/boot/dts/starfive/Makefile | 1 + .../starfive/jh7110-starfive-audio-card.dts | 67 ++ .../jh7110-starfive-visionfive-2.dtsi | 40 ++ arch/riscv/boot/dts/starfive/jh7110.dtsi | 21 + sound/soc/Kconfig | 1 + sound/soc/Makefile | 1 + sound/soc/starfive/Kconfig | 15 + sound/soc/starfive/Makefile | 2 + sound/soc/starfive/jh7110_tdm.c | 579 ++++++++++++++++++ sound/soc/starfive/jh7110_tdm.h | 155 +++++ 13 files changed, 987 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/starfive,jh7110-tdm.yaml create mode 100644 arch/riscv/boot/dts/starfive/jh7110-starfive-audio-card.dts create mode 100644 sound/soc/starfive/Kconfig create mode 100644 sound/soc/starfive/Makefile create mode 100644 sound/soc/starfive/jh7110_tdm.c create mode 100644 sound/soc/starfive/jh7110_tdm.h base-commit: 197b6b60ae7bc51dd0814953c562833143b292aa prerequisite-patch-id: 30bec4dba6f250a6edd0c2cbab2ce09442e50e8a prerequisite-patch-id: bb939c0c7c26b08addfccd890f9d3974b6eaec53 prerequisite-patch-id: 8a6f135bcabdad4a4bfb21f0c6a0ffd2bb57efe7 prerequisite-patch-id: c2366f993a9d85e28c06d8d09f064dd5e8b29a61 prerequisite-patch-id: 50d53a21f91f4087fc80b6f1f72864adfb0002b9 prerequisite-patch-id: 0df3703af91c30f1ca2c47f5609012f2d7200028 prerequisite-patch-id: 89f049f951e5acf75aab92541992f816fd0acc0d prerequisite-patch-id: 551fae54377090044c3612fca9740a9b359abdd2 prerequisite-patch-id: c7fdf904f398d478f0ed6d57eb878982bc73329d prerequisite-patch-id: 1b2d0982b18da060c82134f05bf3ce16425bac8d prerequisite-patch-id: 090ba4b78d47bc19204916e76fdbc70021785388 prerequisite-patch-id: a5d9e0f7d4f8163f566678894cf693015119f2d9 prerequisite-patch-id: 4637a8fa2334a45fa6b64351f4e9e28d3e2d60d3 prerequisite-patch-id: 32647ec60a3b614e1c59ec8e54cb511ae832c22f prerequisite-patch-id: aa06658ecf89c92d0dfdd6a4ba6d9e6e67532971 prerequisite-patch-id: 1387a7e87b446329dfc21f3e575ceae7ebcf954c prerequisite-patch-id: 258ea5f9b8bf41b6981345dcc81795f25865d38f prerequisite-patch-id: 8b6f2c9660c0ac0ee4e73e4c21aca8e6b75e81b9 prerequisite-patch-id: dbb0c0151b8bdf093e6ce79fd2fe3f60791a6e0b prerequisite-patch-id: 9007c8610fdcd387592475949864edde874c20a2 prerequisite-patch-id: d57e95d31686772abc4c4d5aa1cadc344dc293cd prerequisite-patch-id: 9f911969d0a550648493952c99096d26e05d4d83 prerequisite-patch-id: 2ddada18ab6ea5cd1da14212aaf59632f5203d40 prerequisite-patch-id: 80042661ff6156ce577a72e9eb8c0b218b624829 prerequisite-patch-id: 398744c61913c76a35754de867c4f820ca7a8d99 prerequisite-patch-id: f59269382164b5d642a5e10443ca447f5caa595c prerequisite-patch-id: 1babe83d6bf999bad17584dc595480f9070a5369 prerequisite-patch-id: 77be3d122d66df813f13088141ce27b21107a341 prerequisite-patch-id: 9fbb7ad1dd258bb8ff5946c4a0e59de4bfd82a04 prerequisite-patch-id: 6f6984916dffd0cc66aa733c9b6bd3a55495a50c prerequisite-patch-id: 39e1be2a3d1593577ab997f55f59367cba665aa7 prerequisite-patch-id: 584c256c9acb52ee2773d0c81c3f4977fc18155a prerequisite-patch-id: b37ac15032973e1fcd918f157c82a0606775c9e9 prerequisite-patch-id: 32deea16304859842af5c2151bc41d91cf6dfc9b prerequisite-patch-id: 20ac2450fb93b3f69f83fc720fd4800a95e618a6 prerequisite-patch-id: 6abf359fa445f4104432ddee27044dfbfb128417 -- 2.17.1

5 13

[PATCH] ALSA: hda/realtek: Add quirk for ThinkPad P1 Gen 6
by Vitaly Rodionov 27 Apr '23

27 Apr '23

Lenovo ThinkPad P1 Gen 6 laptop has 2 CS35L41 amplifies on I2C bus connected to Realtek codec. Signed-off-by: Vitaly Rodionov <vitalyr(a)opensource.cirrus.com> --- sound/pci/hda/patch_realtek.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index ab938fa1d65d..d973ebb77743 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -9691,6 +9691,8 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x17aa, 0x22f1, "Thinkpad", ALC287_FIXUP_CS35L41_I2C_2), SND_PCI_QUIRK(0x17aa, 0x22f2, "Thinkpad", ALC287_FIXUP_CS35L41_I2C_2), SND_PCI_QUIRK(0x17aa, 0x22f3, "Thinkpad", ALC287_FIXUP_CS35L41_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x2316, "Thinkpad P1 Gen 6", ALC287_FIXUP_CS35L41_I2C_2), + SND_PCI_QUIRK(0x17aa, 0x2317, "Thinkpad P1 Gen 6", ALC287_FIXUP_CS35L41_I2C_2), SND_PCI_QUIRK(0x17aa, 0x30bb, "ThinkCentre AIO", ALC233_FIXUP_LENOVO_LINE2_MIC_HOTKEY), SND_PCI_QUIRK(0x17aa, 0x30e2, "ThinkCentre AIO", ALC233_FIXUP_LENOVO_LINE2_MIC_HOTKEY), SND_PCI_QUIRK(0x17aa, 0x310c, "ThinkCentre Station", ALC294_FIXUP_LENOVO_MIC_LOCATION), -- 2.34.1

2 1

USB sound card freezes USB after resume from suspend
by Jakub Kicinski 26 Apr '23

26 Apr '23

Hi! For a few weeks now I can't use any USB devices if I suspend my laptop with my USB sound card active and resuming it without it connected. USB worker threads seems to be sitting in: [<0>] snd_pcm_dev_disconnect+0x1e8/0x280 [snd_pcm] [<0>] snd_device_disconnect_all+0x42/0x80 [snd] [<0>] snd_card_disconnect+0x128/0x290 [snd] [<0>] usb_audio_disconnect+0x11a/0x2c0 [snd_usb_audio] [<0>] usb_unbind_interface+0x8c/0x270 [<0>] device_release_driver_internal+0x1b2/0x230 [<0>] bus_remove_device+0xd8/0x150 [<0>] device_del+0x18b/0x410 [<0>] usb_disable_device+0xc6/0x1e0 [<0>] usb_disconnect+0xda/0x2c0 [<0>] usb_disconnect+0xbf/0x2c0 [<0>] usb_disconnect+0xbf/0x2c0 [<0>] usb_disconnect+0xbf/0x2c0 [<0>] hub_event+0xf01/0x1cd0 [<0>] process_one_work+0x1c4/0x3d0 [<0>] worker_thread+0x4d/0x380 [<0>] kthread+0xe6/0x110 [<0>] ret_from_fork+0x29/0x50 Which is: snd_pcm_dev_disconnect (/usr/src/debug/kernel-6.2.12/linux-6.2.12-300.fc38.x86_64/sound/core/pcm.c:818 /usr/src/debug/kernel-6.2.12/linux-6.2.12-300.fc38.x86_64/sound/core/pcm.c:812 /usr/src/debug/kernel-6.2.12/linux-6.2.12-300.fc38.x86_64/sound/core/pcm.c:1129) snd_pcm It happens on Fedora 37 and Fedora 38, it seems to have coincided with the 6.2 kernel but I'm not 100% sure. The USB devices come back after half an hour or so, silently. There's nothing of note in dmesg.

4 8

[PATCH 0/9] Add Chameleon v3 ASoC audio
by Paweł Anikiel 26 Apr '23

26 Apr '23

The Google Chameleon v3 is a device made for testing audio and video paths of other devices. This patchset adds support for ASoC audio on this device. It has two audio sources: HDMI audio from the it68051 chip (RX only), and analog audio from the ssm2603 chip (RX and TX). The patchset adds the ASoC platform and machine drivers, as well as some changes to the existing ssm2602 codec driver. Paweł Anikiel (9): ASoC: Add Chameleon v3 audio dt-bindings: ASoC: Add chv3-i2s dt-bindings: ASoC: Add chv3-audio dt-bindings: ASoC: Add it68051 ASoC: ssm2602: Add workaround for playback with external MCLK ASoC: ssm2602: Add support for CLKDIV2 ASoC: ssm2602: Add mute gpio dt-bindings: ASoC: Add mute-gpio to ssm2602 ARM: dts: chameleonv3: Add ssm2603 mute gpio .../devicetree/bindings/sound/adi,ssm2602.txt | 4 + .../bindings/sound/google,chv3-audio.yaml | 49 +++ .../bindings/sound/google,chv3-i2s.yaml | 42 +++ .../bindings/sound/ite,it68051.yaml | 23 ++ .../boot/dts/socfpga_arria10_chameleonv3.dts | 30 ++ sound/soc/Kconfig | 1 + sound/soc/Makefile | 1 + sound/soc/chameleonv3/Kconfig | 7 + sound/soc/chameleonv3/Makefile | 2 + sound/soc/chameleonv3/chv3-audio.c | 111 ++++++ sound/soc/chameleonv3/chv3-i2s.c | 347 ++++++++++++++++++ sound/soc/chameleonv3/chv3-it68051.c | 41 +++ sound/soc/codecs/ssm2602.c | 37 +- 13 files changed, 692 insertions(+), 3 deletions(-) create mode 100644 Documentation/devicetree/bindings/sound/google,chv3-audio.yaml create mode 100644 Documentation/devicetree/bindings/sound/google,chv3-i2s.yaml create mode 100644 Documentation/devicetree/bindings/sound/ite,it68051.yaml create mode 100644 sound/soc/chameleonv3/Kconfig create mode 100644 sound/soc/chameleonv3/Makefile create mode 100644 sound/soc/chameleonv3/chv3-audio.c create mode 100644 sound/soc/chameleonv3/chv3-i2s.c create mode 100644 sound/soc/chameleonv3/chv3-it68051.c -- 2.40.0.634.g4ca3ef3211-goog

4 29

[PATCH 1/2] ASoC: amd: ps: remove the register read and write wrappers.
by Syed Saba Kareem 26 Apr '23

26 Apr '23

Instead of acp63_readl() and acp63_writel() wrappers readl and writel functions can be used directly. Remove acp63_readl() and acp63_writel() wrappers. Signed-off-by: Syed Saba Kareem <Syed.SabaKareem(a)amd.com> Reviewed-by: Vijendar Mukunda <Vijendar.Mukunda(a)amd.com> --- sound/soc/amd/ps/acp63.h | 10 ------ sound/soc/amd/ps/pci-ps.c | 33 +++++++++--------- sound/soc/amd/ps/ps-pdm-dma.c | 63 +++++++++++++++++------------------ 3 files changed, 46 insertions(+), 60 deletions(-) diff --git a/sound/soc/amd/ps/acp63.h b/sound/soc/amd/ps/acp63.h index dd36790b25ae..16eeda3fbdbd 100644 --- a/sound/soc/amd/ps/acp63.h +++ b/sound/soc/amd/ps/acp63.h @@ -92,16 +92,6 @@ struct pdm_dev_data { struct snd_pcm_substream *capture_stream; }; -static inline u32 acp63_readl(void __iomem *base_addr) -{ - return readl(base_addr); -} - -static inline void acp63_writel(u32 val, void __iomem *base_addr) -{ - writel(val, base_addr); -} - struct acp63_dev_data { void __iomem *acp63_base; struct resource *res; diff --git a/sound/soc/amd/ps/pci-ps.c b/sound/soc/amd/ps/pci-ps.c index afddb9a77ba4..097fd5488534 100644 --- a/sound/soc/amd/ps/pci-ps.c +++ b/sound/soc/amd/ps/pci-ps.c @@ -22,16 +22,16 @@ static int acp63_power_on(void __iomem *acp_base) u32 val; int timeout; - val = acp63_readl(acp_base + ACP_PGFSM_STATUS); + val = readl(acp_base + ACP_PGFSM_STATUS); if (!val) return val; if ((val & ACP_PGFSM_STATUS_MASK) != ACP_POWER_ON_IN_PROGRESS) - acp63_writel(ACP_PGFSM_CNTL_POWER_ON_MASK, acp_base + ACP_PGFSM_CONTROL); + writel(ACP_PGFSM_CNTL_POWER_ON_MASK, acp_base + ACP_PGFSM_CONTROL); timeout = 0; while (++timeout < 500) { - val = acp63_readl(acp_base + ACP_PGFSM_STATUS); + val = readl(acp_base + ACP_PGFSM_STATUS); if (!val) return 0; udelay(1); @@ -44,18 +44,18 @@ static int acp63_reset(void __iomem *acp_base) u32 val; int timeout; - acp63_writel(1, acp_base + ACP_SOFT_RESET); + writel(1, acp_base + ACP_SOFT_RESET); timeout = 0; while (++timeout < 500) { - val = acp63_readl(acp_base + ACP_SOFT_RESET); + val = readl(acp_base + ACP_SOFT_RESET); if (val & ACP_SOFT_RESET_SOFTRESET_AUDDONE_MASK) break; cpu_relax(); } - acp63_writel(0, acp_base + ACP_SOFT_RESET); + writel(0, acp_base + ACP_SOFT_RESET); timeout = 0; while (++timeout < 500) { - val = acp63_readl(acp_base + ACP_SOFT_RESET); + val = readl(acp_base + ACP_SOFT_RESET); if (!val) return 0; cpu_relax(); @@ -65,15 +65,14 @@ static int acp63_reset(void __iomem *acp_base) static void acp63_enable_interrupts(void __iomem *acp_base) { - acp63_writel(1, acp_base + ACP_EXTERNAL_INTR_ENB); + writel(1, acp_base + ACP_EXTERNAL_INTR_ENB); } static void acp63_disable_interrupts(void __iomem *acp_base) { - acp63_writel(ACP_EXT_INTR_STAT_CLEAR_MASK, acp_base + - ACP_EXTERNAL_INTR_STAT); - acp63_writel(0, acp_base + ACP_EXTERNAL_INTR_CNTL); - acp63_writel(0, acp_base + ACP_EXTERNAL_INTR_ENB); + writel(ACP_EXT_INTR_STAT_CLEAR_MASK, acp_base + ACP_EXTERNAL_INTR_STAT); + writel(0, acp_base + ACP_EXTERNAL_INTR_CNTL); + writel(0, acp_base + ACP_EXTERNAL_INTR_ENB); } static int acp63_init(void __iomem *acp_base, struct device *dev) @@ -85,7 +84,7 @@ static int acp63_init(void __iomem *acp_base, struct device *dev) dev_err(dev, "ACP power on failed\n"); return ret; } - acp63_writel(0x01, acp_base + ACP_CONTROL); + writel(0x01, acp_base + ACP_CONTROL); ret = acp63_reset(acp_base); if (ret) { dev_err(dev, "ACP reset failed\n"); @@ -105,7 +104,7 @@ static int acp63_deinit(void __iomem *acp_base, struct device *dev) dev_err(dev, "ACP reset failed\n"); return ret; } - acp63_writel(0, acp_base + ACP_CONTROL); + writel(0, acp_base + ACP_CONTROL); return 0; } @@ -120,11 +119,11 @@ static irqreturn_t acp63_irq_handler(int irq, void *dev_id) if (!adata) return IRQ_NONE; - val = acp63_readl(adata->acp63_base + ACP_EXTERNAL_INTR_STAT); + val = readl(adata->acp63_base + ACP_EXTERNAL_INTR_STAT); if (val & BIT(PDM_DMA_STAT)) { pdev_index = adata->pdm_dev_index; ps_pdm_data = dev_get_drvdata(&adata->pdev[pdev_index]->dev); - acp63_writel(BIT(PDM_DMA_STAT), adata->acp63_base + ACP_EXTERNAL_INTR_STAT); + writel(BIT(PDM_DMA_STAT), adata->acp63_base + ACP_EXTERNAL_INTR_STAT); if (ps_pdm_data->capture_stream) snd_pcm_period_elapsed(ps_pdm_data->capture_stream); return IRQ_HANDLED; @@ -302,7 +301,7 @@ static int snd_acp63_probe(struct pci_dev *pci, dev_err(&pci->dev, "ACP PCI IRQ request failed\n"); goto de_init; } - val = acp63_readl(adata->acp63_base + ACP_PIN_CONFIG); + val = readl(adata->acp63_base + ACP_PIN_CONFIG); get_acp63_device_config(val, pci, adata); ret = create_acp63_platform_devs(pci, adata, addr); if (ret < 0) { diff --git a/sound/soc/amd/ps/ps-pdm-dma.c b/sound/soc/amd/ps/ps-pdm-dma.c index 46b91327168f..3ecc6cf3fd34 100644 --- a/sound/soc/amd/ps/ps-pdm-dma.c +++ b/sound/soc/amd/ps/ps-pdm-dma.c @@ -45,10 +45,10 @@ static const struct snd_pcm_hardware acp63_pdm_hardware_capture = { static void acp63_init_pdm_ring_buffer(u32 physical_addr, u32 buffer_size, u32 watermark_size, void __iomem *acp_base) { - acp63_writel(physical_addr, acp_base + ACP_WOV_RX_RINGBUFADDR); - acp63_writel(buffer_size, acp_base + ACP_WOV_RX_RINGBUFSIZE); - acp63_writel(watermark_size, acp_base + ACP_WOV_RX_INTR_WATERMARK_SIZE); - acp63_writel(0x01, acp_base + ACPAXI2AXI_ATU_CTRL); + writel(physical_addr, acp_base + ACP_WOV_RX_RINGBUFADDR); + writel(buffer_size, acp_base + ACP_WOV_RX_RINGBUFSIZE); + writel(watermark_size, acp_base + ACP_WOV_RX_INTR_WATERMARK_SIZE); + writel(0x01, acp_base + ACPAXI2AXI_ATU_CTRL); } static void acp63_enable_pdm_clock(void __iomem *acp_base) @@ -58,11 +58,11 @@ static void acp63_enable_pdm_clock(void __iomem *acp_base) pdm_clk_enable = ACP_PDM_CLK_FREQ_MASK; pdm_ctrl = 0x00; - acp63_writel(pdm_clk_enable, acp_base + ACP_WOV_CLK_CTRL); - pdm_ctrl = acp63_readl(acp_base + ACP_WOV_MISC_CTRL); + writel(pdm_clk_enable, acp_base + ACP_WOV_CLK_CTRL); + pdm_ctrl = readl(acp_base + ACP_WOV_MISC_CTRL); pdm_ctrl &= ~ACP_WOV_GAIN_CONTROL; pdm_ctrl |= FIELD_PREP(ACP_WOV_GAIN_CONTROL, clamp(pdm_gain, 0, 3)); - acp63_writel(pdm_ctrl, acp_base + ACP_WOV_MISC_CTRL); + writel(pdm_ctrl, acp_base + ACP_WOV_MISC_CTRL); } static void acp63_enable_pdm_interrupts(struct pdm_dev_data *adata) @@ -70,9 +70,9 @@ static void acp63_enable_pdm_interrupts(struct pdm_dev_data *adata) u32 ext_int_ctrl; mutex_lock(adata->acp_lock); - ext_int_ctrl = acp63_readl(adata->acp63_base + ACP_EXTERNAL_INTR_CNTL); + ext_int_ctrl = readl(adata->acp63_base + ACP_EXTERNAL_INTR_CNTL); ext_int_ctrl |= PDM_DMA_INTR_MASK; - acp63_writel(ext_int_ctrl, adata->acp63_base + ACP_EXTERNAL_INTR_CNTL); + writel(ext_int_ctrl, adata->acp63_base + ACP_EXTERNAL_INTR_CNTL); mutex_unlock(adata->acp_lock); } @@ -81,9 +81,9 @@ static void acp63_disable_pdm_interrupts(struct pdm_dev_data *adata) u32 ext_int_ctrl; mutex_lock(adata->acp_lock); - ext_int_ctrl = acp63_readl(adata->acp63_base + ACP_EXTERNAL_INTR_CNTL); + ext_int_ctrl = readl(adata->acp63_base + ACP_EXTERNAL_INTR_CNTL); ext_int_ctrl &= ~PDM_DMA_INTR_MASK; - acp63_writel(ext_int_ctrl, adata->acp63_base + ACP_EXTERNAL_INTR_CNTL); + writel(ext_int_ctrl, adata->acp63_base + ACP_EXTERNAL_INTR_CNTL); mutex_unlock(adata->acp_lock); } @@ -93,8 +93,8 @@ static bool acp63_check_pdm_dma_status(void __iomem *acp_base) u32 pdm_enable, pdm_dma_enable; pdm_dma_status = false; - pdm_enable = acp63_readl(acp_base + ACP_WOV_PDM_ENABLE); - pdm_dma_enable = acp63_readl(acp_base + ACP_WOV_PDM_DMA_ENABLE); + pdm_enable = readl(acp_base + ACP_WOV_PDM_ENABLE); + pdm_dma_enable = readl(acp_base + ACP_WOV_PDM_DMA_ENABLE); if ((pdm_enable & ACP_PDM_ENABLE) && (pdm_dma_enable & ACP_PDM_DMA_EN_STATUS)) pdm_dma_status = true; @@ -111,11 +111,11 @@ static int acp63_start_pdm_dma(void __iomem *acp_base) pdm_dma_enable = 0x01; acp63_enable_pdm_clock(acp_base); - acp63_writel(pdm_enable, acp_base + ACP_WOV_PDM_ENABLE); - acp63_writel(pdm_dma_enable, acp_base + ACP_WOV_PDM_DMA_ENABLE); + writel(pdm_enable, acp_base + ACP_WOV_PDM_ENABLE); + writel(pdm_dma_enable, acp_base + ACP_WOV_PDM_DMA_ENABLE); timeout = 0; while (++timeout < ACP_COUNTER) { - pdm_dma_enable = acp63_readl(acp_base + ACP_WOV_PDM_DMA_ENABLE); + pdm_dma_enable = readl(acp_base + ACP_WOV_PDM_DMA_ENABLE); if ((pdm_dma_enable & 0x02) == ACP_PDM_DMA_EN_STATUS) return 0; udelay(DELAY_US); @@ -131,14 +131,14 @@ static int acp63_stop_pdm_dma(void __iomem *acp_base) pdm_enable = 0x00; pdm_dma_enable = 0x00; - pdm_enable = acp63_readl(acp_base + ACP_WOV_PDM_ENABLE); - pdm_dma_enable = acp63_readl(acp_base + ACP_WOV_PDM_DMA_ENABLE); + pdm_enable = readl(acp_base + ACP_WOV_PDM_ENABLE); + pdm_dma_enable = readl(acp_base + ACP_WOV_PDM_DMA_ENABLE); if (pdm_dma_enable & 0x01) { pdm_dma_enable = 0x02; - acp63_writel(pdm_dma_enable, acp_base + ACP_WOV_PDM_DMA_ENABLE); + writel(pdm_dma_enable, acp_base + ACP_WOV_PDM_DMA_ENABLE); timeout = 0; while (++timeout < ACP_COUNTER) { - pdm_dma_enable = acp63_readl(acp_base + ACP_WOV_PDM_DMA_ENABLE); + pdm_dma_enable = readl(acp_base + ACP_WOV_PDM_DMA_ENABLE); if ((pdm_dma_enable & 0x02) == 0x00) break; udelay(DELAY_US); @@ -148,9 +148,9 @@ static int acp63_stop_pdm_dma(void __iomem *acp_base) } if (pdm_enable == ACP_PDM_ENABLE) { pdm_enable = ACP_PDM_DISABLE; - acp63_writel(pdm_enable, acp_base + ACP_WOV_PDM_ENABLE); + writel(pdm_enable, acp_base + ACP_WOV_PDM_ENABLE); } - acp63_writel(0x01, acp_base + ACP_WOV_PDM_FIFO_FLUSH); + writel(0x01, acp_base + ACP_WOV_PDM_FIFO_FLUSH); return 0; } @@ -164,18 +164,16 @@ static void acp63_config_dma(struct pdm_stream_instance *rtd, int direction) val = PDM_PTE_OFFSET; /* Group Enable */ - acp63_writel(ACP_SRAM_PTE_OFFSET | BIT(31), rtd->acp63_base + - ACPAXI2AXI_ATU_BASE_ADDR_GRP_1); - acp63_writel(PAGE_SIZE_4K_ENABLE, rtd->acp63_base + - ACPAXI2AXI_ATU_PAGE_SIZE_GRP_1); + writel(ACP_SRAM_PTE_OFFSET | BIT(31), rtd->acp63_base + ACPAXI2AXI_ATU_BASE_ADDR_GRP_1); + writel(PAGE_SIZE_4K_ENABLE, rtd->acp63_base + ACPAXI2AXI_ATU_PAGE_SIZE_GRP_1); for (page_idx = 0; page_idx < rtd->num_pages; page_idx++) { /* Load the low address of page int ACP SRAM through SRBM */ low = lower_32_bits(addr); high = upper_32_bits(addr); - acp63_writel(low, rtd->acp63_base + ACP_SCRATCH_REG_0 + val); + writel(low, rtd->acp63_base + ACP_SCRATCH_REG_0 + val); high |= BIT(31); - acp63_writel(high, rtd->acp63_base + ACP_SCRATCH_REG_0 + val + 4); + writel(high, rtd->acp63_base + ACP_SCRATCH_REG_0 + val + 4); val += 8; addr += PAGE_SIZE; } @@ -242,9 +240,9 @@ static u64 acp63_pdm_get_byte_count(struct pdm_stream_instance *rtd, u32 high, low; u64 byte_count; - high = acp63_readl(rtd->acp63_base + ACP_WOV_RX_LINEARPOSITIONCNTR_HIGH); + high = readl(rtd->acp63_base + ACP_WOV_RX_LINEARPOSITIONCNTR_HIGH); byte_count = high; - low = acp63_readl(rtd->acp63_base + ACP_WOV_RX_LINEARPOSITIONCNTR_LOW); + low = readl(rtd->acp63_base + ACP_WOV_RX_LINEARPOSITIONCNTR_LOW); byte_count = (byte_count << 32) | low; return byte_count; } @@ -309,9 +307,8 @@ static int acp63_pdm_dai_trigger(struct snd_pcm_substream *substream, case SNDRV_PCM_TRIGGER_START: case SNDRV_PCM_TRIGGER_RESUME: case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: - acp63_writel(ch_mask, rtd->acp63_base + ACP_WOV_PDM_NO_OF_CHANNELS); - acp63_writel(PDM_DECIMATION_FACTOR, rtd->acp63_base + - ACP_WOV_PDM_DECIMATION_FACTOR); + writel(ch_mask, rtd->acp63_base + ACP_WOV_PDM_NO_OF_CHANNELS); + writel(PDM_DECIMATION_FACTOR, rtd->acp63_base + ACP_WOV_PDM_DECIMATION_FACTOR); rtd->bytescount = acp63_pdm_get_byte_count(rtd, substream->stream); pdm_status = acp63_check_pdm_dma_status(rtd->acp63_base); if (!pdm_status) -- 2.25.1

1 1

[PATCH v3] ALSA: hda: Glenfly: add HD Audio PCI IDs and HDMI Codec Vendor IDs.
by Reaper Li 26 Apr '23

26 Apr '23

From: jasontao <jasontao(a)glenfly.com> Add a set of HD Audio PCI IDS, and the HDMI codec vendor IDs for Glenfly Gpus. - In default_bdl_pos_adj, set bdl to 128 as Glenfly Gpus have hardware limitation, need to increase hdac interrupt interval. - In azx_first_init, enable polling mode for Glenfly Gpu. When the codec complete the command, it sends interrupt and writes response entries to memory, howerver, the write requests sometimes are not actually synchronized to memory when driver handle hdac interrupt on Glenfly Gpus. If the RIRB status is not updated in the interrupt handler, azx_rirb_get_response keeps trying to recevie a response from rirb until 1s timeout. Enabling polling mode for Glenfly Gpu can fix the issue. - In patch_gf_hdmi, set Glenlfy Gpu Codec's no_sticky_stream as it need driver to do actual clean-ups for the linked codec when switch from one codec to another. Signed-off-by: jasontao <jasontao(a)glenfly.com> Signed-off-by: Reaper Li <reaperlioc(a)glenfly.com> --- v3: fix warnings for the patch. v2: add some comments for code and details in the commit log. sound/pci/hda/hda_intel.c | 21 +++++++++++++++++++++ sound/pci/hda/patch_hdmi.c | 22 ++++++++++++++++++++++ 2 files changed, 43 insertions(+) diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c index 77a592f21..31e16feaa 100644 --- a/sound/pci/hda/hda_intel.c +++ b/sound/pci/hda/hda_intel.c @@ -227,6 +227,7 @@ enum { AZX_DRIVER_ATI, AZX_DRIVER_ATIHDMI, AZX_DRIVER_ATIHDMI_NS, + AZX_DRIVER_GFHDMI, AZX_DRIVER_VIA, AZX_DRIVER_SIS, AZX_DRIVER_ULI, @@ -349,6 +350,7 @@ static const char * const driver_short_names[] = { [AZX_DRIVER_ATI] = "HDA ATI SB", [AZX_DRIVER_ATIHDMI] = "HDA ATI HDMI", [AZX_DRIVER_ATIHDMI_NS] = "HDA ATI HDMI", + [AZX_DRIVER_GFHDMI] = "HDA GF HDMI", [AZX_DRIVER_VIA] = "HDA VIA VT82xx", [AZX_DRIVER_SIS] = "HDA SIS966", [AZX_DRIVER_ULI] = "HDA ULI M5461", @@ -1743,6 +1745,12 @@ static int default_bdl_pos_adj(struct azx *chip) } switch (chip->driver_type) { + /* + * increase the bdl size for Glenfly Gpus for hardware + * limitation on hdac interrupt interval + */ + case AZX_DRIVER_GFHDMI: + return 128; case AZX_DRIVER_ICH: case AZX_DRIVER_PCH: return 1; @@ -1858,6 +1866,12 @@ static int azx_first_init(struct azx *chip) pci_write_config_dword(pci, PCI_BASE_ADDRESS_1, 0); } #endif + /* + * Fix response write request not synced to memory when handle + * hdac interrupt on Glenfly Gpus + */ + if (chip->driver_type == AZX_DRIVER_GFHDMI) + bus->polling_mode = 1; err = pcim_iomap_regions(pci, 1 << 0, "ICH HD audio"); if (err < 0) @@ -1959,6 +1973,7 @@ static int azx_first_init(struct azx *chip) chip->playback_streams = ATIHDMI_NUM_PLAYBACK; chip->capture_streams = ATIHDMI_NUM_CAPTURE; break; + case AZX_DRIVER_GFHDMI: case AZX_DRIVER_GENERIC: default: chip->playback_streams = ICH6_NUM_PLAYBACK; @@ -2724,6 +2739,12 @@ static const struct pci_device_id azx_ids[] = { { PCI_DEVICE(0x1002, 0xab38), .driver_data = AZX_DRIVER_ATIHDMI_NS | AZX_DCAPS_PRESET_ATI_HDMI_NS | AZX_DCAPS_PM_RUNTIME }, + /* GLENFLY */ + { PCI_DEVICE(0x6766, PCI_ANY_ID), + .class = PCI_CLASS_MULTIMEDIA_HD_AUDIO << 8, + .class_mask = 0xffffff, + .driver_data = AZX_DRIVER_GFHDMI | AZX_DCAPS_POSFIX_LPIB | + AZX_DCAPS_NO_MSI | AZX_DCAPS_NO_64BIT }, /* VIA VT8251/VT8237A */ { PCI_DEVICE(0x1106, 0x3288), .driver_data = AZX_DRIVER_VIA }, /* VIA GFX VT7122/VX900 */ diff --git a/sound/pci/hda/patch_hdmi.c b/sound/pci/hda/patch_hdmi.c index 4ffa3a59f..0a1daef9d 100644 --- a/sound/pci/hda/patch_hdmi.c +++ b/sound/pci/hda/patch_hdmi.c @@ -4489,6 +4489,22 @@ static int patch_via_hdmi(struct hda_codec *codec) return patch_simple_hdmi(codec, VIAHDMI_CVT_NID, VIAHDMI_PIN_NID); } +static int patch_gf_hdmi(struct hda_codec *codec) +{ + int err; + + err = patch_generic_hdmi(codec); + if (err) + return err; + + /* + * Glenfly GPUs have two codecs, stream switches from one codec to + * another, need to do actual clean-ups in codec_cleanup_stream + */ + codec->no_sticky_stream = 1; + return 0; +} + /* * patch entries */ @@ -4579,6 +4595,12 @@ HDA_CODEC_ENTRY(0x10de009f, "GPU 9f HDMI/DP", patch_nvhdmi), HDA_CODEC_ENTRY(0x10de00a0, "GPU a0 HDMI/DP", patch_nvhdmi), HDA_CODEC_ENTRY(0x10de8001, "MCP73 HDMI", patch_nvhdmi_2ch), HDA_CODEC_ENTRY(0x10de8067, "MCP67/68 HDMI", patch_nvhdmi_2ch), +HDA_CODEC_ENTRY(0x67663d82, "Arise 82 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d83, "Arise 83 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d84, "Arise 84 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d85, "Arise 85 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d86, "Arise 86 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d87, "Arise 87 HDMI/DP", patch_gf_hdmi), HDA_CODEC_ENTRY(0x11069f80, "VX900 HDMI/DP", patch_via_hdmi), HDA_CODEC_ENTRY(0x11069f81, "VX900 HDMI/DP", patch_via_hdmi), HDA_CODEC_ENTRY(0x11069f84, "VX11 HDMI/DP", patch_generic_hdmi), -- 2.20.1

2 1

Change of delay computation by ALSA firewire stack at v6.3 kernel
by Takashi Sakamoto 26 Apr '23

26 Apr '23

Hi, Linux kernel v6.3 is out a few days ago, which includes a change to ALSA firewire stack that addresses an issue affecting user space applications. Specifically, the change introduces delay compensation with the current isochronous cycle in IEEE 1394 bus. In UAPI of sound subsystem, `struct snd_pcm_status` is used to report status of runtime for PCM substream. User space application read the `delay` field of structure to obtain the number of PCM frames[1], which is comprised of two parts; one common to all drivers, and one specific to individual drivers. The common part of the delay value reflects the gap between the pointer at which the application reads/writes PCM frames (applptr) and the pointer at which the driver receives/transmits the latest audio data frames (hwptr). The driver can increase this value arbitrarily based on the transmission method used. In the current implementation of drivers in ALSA firewire stack, initial isochronous packets are scheduled to deliver audio data frames equivalent to the size of PCM buffer configured by user space application as part of the hardware parameters. In the case of PipeWire, 4,096 frames is used as a default value at a sample rate of 48.0 kHz for the size of PCM buffer[2], resulting in 684 initial packets[3] equivalent to 4,104 frames[4]. 1394 OHCI hardware enables software to read the current isochronous cycle with a resolution of 8,000 times per second[5]. The change to ALSA firewire stack involves using the specific part of delay to report the gap between the current isochronous cycle and the isochronous cycle at which hwptr is located[6]. Prior to the change, the gap was not visible to user space applications, leading to unexpected delay[7]. For capture PCM substream, the gap is zero or a few packets, as 1394 OHCI hardware enables software to read the payload of isochronous packets immediately upon their arrival. The delay mostly comes from the common part, thus it is 4,096 or so as maximum in the case of PipeWire. For playback PCM substream, the maximum gap is equivalent to 684 initial packets, resulting in the delay ranging from 4,104 frames to 8,200 frames (= 4,096 + 4,104) in the case of PipeWire. Regardless of the driver and its transmission backend, I note that there is a limiting point beyond which the value of delay field cannot express true delay between the timing at which the application reads/writes PCM frames and the timing at which the hardware actually generates audio and samples audio signal, since the driver is only responsible for transmitting the audio data frame in the context[8], and cannot account for the circuit-level details on the board. While a driver that accounts for such details could result in more accurate delay measurements, such an implementation would be technically difficult, particularly for devices with thick implementations between transmission of audio data frames and audio signal processing (i.e. devices for packet-oriented communication). [1] include/sound/pcm.h https://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git/tree/includ… [2] at least pipewire version 0.3.58 [3] 684 = 8,000 * 4,096 / 48,000. You can see the computation at: https://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git/tree/sound/… [4] 4,104 = 48,000 * 684 / 8000. In IEC 61883-1/6, packet includes multiple audio data frames. [5] The drivers can retrieve the cycle since v5.19 or later, by a commit baa914cd81f5 ("firewire: add kernel API to access CYCLE_TIME register") https://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git/commit/?id=… [6] It was finally done by a commit af13842cad44 ("ALSA: firewire-lib: compute extra delay for runtime of PCM substream") https://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git/commit/?id=… [7] [pipewire-jack] Systematic delay in recording using REAPER of 0.07 to 0.08 seconds https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/2790 [8] In the most cases, the transmission itself is executed out of sound subsystem. Thanks Takashi Sakamoto

1 0

[PATCH] ASoC: dwc: add reset support
by Maxim Kochetkov 26 Apr '23

26 Apr '23

Some SoC may have resets for I2S subsystem. So add optional reset deassert at startup. Signed-off-by: Maxim Kochetkov <fido_max(a)inbox.ru> --- sound/soc/dwc/dwc-i2s.c | 9 +++++++++ sound/soc/dwc/local.h | 1 + 2 files changed, 10 insertions(+) diff --git a/sound/soc/dwc/dwc-i2s.c b/sound/soc/dwc/dwc-i2s.c index acdf98b2ee9c..8c8bc7116f86 100644 --- a/sound/soc/dwc/dwc-i2s.c +++ b/sound/soc/dwc/dwc-i2s.c @@ -17,6 +17,7 @@ #include <linux/io.h> #include <linux/interrupt.h> #include <linux/module.h> +#include <linux/reset.h> #include <linux/slab.h> #include <linux/pm_runtime.h> #include <sound/designware_i2s.h> @@ -648,6 +649,14 @@ static int dw_i2s_probe(struct platform_device *pdev) if (IS_ERR(dev->i2s_base)) return PTR_ERR(dev->i2s_base); + dev->reset = devm_reset_control_array_get_optional_shared(&pdev->dev); + if (IS_ERR(dev->reset)) + return PTR_ERR(dev->reset); + + ret = reset_control_deassert(dev->reset); + if (ret) + return ret; + dev->dev = &pdev->dev; irq = platform_get_irq_optional(pdev, 0); diff --git a/sound/soc/dwc/local.h b/sound/soc/dwc/local.h index 1c361eb6127e..d64bd4f8fd34 100644 --- a/sound/soc/dwc/local.h +++ b/sound/soc/dwc/local.h @@ -89,6 +89,7 @@ union dw_i2s_snd_dma_data { struct dw_i2s_dev { void __iomem *i2s_base; struct clk *clk; + struct reset_control *reset; int active; unsigned int capability; unsigned int quirks; -- 2.39.2

3 4

[PATCH] ALSA: hda: patch_realtek: add quirk for Asus N7601ZM
by Pierre-Louis Bossart 26 Apr '23

26 Apr '23

Add pins and verbs needed to enable speakers and jack. The pins and verbs configurations were identified by snooping the Windows driver commands, with a nice write-up here: https://brakkee.org/site/2023/02/07/fixing-sound-on-the-asus-n7601zm/ Reported-by: Erik Brakkee <erik(a)brakkee.org> Tested-by: Erik Brakkee <erik(a)brakkee.org> Link: https://github.com/thesofproject/linux/issues/4176 Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart(a)linux.intel.com> Reviewed-by: Kai Vehmanen <kai.vehmanen(a)linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao(a)linux.intel.com> --- sound/pci/hda/patch_realtek.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index b501f9489fc1..2baeb6efbdc7 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -6959,6 +6959,8 @@ enum { ALC269_FIXUP_DELL_M101Z, ALC269_FIXUP_SKU_IGNORE, ALC269_FIXUP_ASUS_G73JW, + ALC269_FIXUP_ASUS_N7601ZM_PINS, + ALC269_FIXUP_ASUS_N7601ZM, ALC269_FIXUP_LENOVO_EAPD, ALC275_FIXUP_SONY_HWEQ, ALC275_FIXUP_SONY_DISABLE_AAMIX, @@ -7255,6 +7257,29 @@ static const struct hda_fixup alc269_fixups[] = { { } } }, + [ALC269_FIXUP_ASUS_N7601ZM_PINS] = { + .type = HDA_FIXUP_PINS, + .v.pins = (const struct hda_pintbl[]) { + { 0x19, 0x03A11050 }, + { 0x1a, 0x03A11C30 }, + { 0x21, 0x03211420 }, + { } + } + }, + [ALC269_FIXUP_ASUS_N7601ZM] = { + .type = HDA_FIXUP_VERBS, + .v.verbs = (const struct hda_verb[]) { + {0x20, AC_VERB_SET_COEF_INDEX, 0x62}, + {0x20, AC_VERB_SET_PROC_COEF, 0xa007}, + {0x20, AC_VERB_SET_COEF_INDEX, 0x10}, + {0x20, AC_VERB_SET_PROC_COEF, 0x8420}, + {0x20, AC_VERB_SET_COEF_INDEX, 0x0f}, + {0x20, AC_VERB_SET_PROC_COEF, 0x7774}, + { } + }, + .chained = true, + .chain_id = ALC269_FIXUP_ASUS_N7601ZM_PINS, + }, [ALC269_FIXUP_LENOVO_EAPD] = { .type = HDA_FIXUP_VERBS, .v.verbs = (const struct hda_verb[]) { @@ -9485,6 +9510,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x1043, 0x19ce, "ASUS B9450FA", ALC294_FIXUP_ASUS_HPE), SND_PCI_QUIRK(0x1043, 0x19e1, "ASUS UX581LV", ALC295_FIXUP_ASUS_MIC_NO_PRESENCE), SND_PCI_QUIRK(0x1043, 0x1a13, "Asus G73Jw", ALC269_FIXUP_ASUS_G73JW), + SND_PCI_QUIRK(0x1043, 0x12a3, "Asus N7691ZM", ALC269_FIXUP_ASUS_N7601ZM), SND_PCI_QUIRK(0x1043, 0x1a30, "ASUS X705UD", ALC256_FIXUP_ASUS_MIC), SND_PCI_QUIRK(0x1043, 0x1a8f, "ASUS UX582ZS", ALC245_FIXUP_CS35L41_SPI_2), SND_PCI_QUIRK(0x1043, 0x1b11, "ASUS UX431DA", ALC294_FIXUP_ASUS_COEF_1B), -- 2.37.2

2 3

USB Audio (HyperX DuoCast) Microphone record volume is too low
by GitHub issues - opened 26 Apr '23

26 Apr '23

alsa-project/alsa-ucm-conf issue #308 was opened from nitin88: Hi, I purchased HyperX DuoCast for office meetings and avoid through whole hoop of Motherboard specific PCIe sound card issues and support as I use pretty much latest hardware. But the sound issues around Linux is still killing me. 1. My DuoCast hardware gain set to Max and still the record volume is too low. 2. Alsamixer disabled Mic volume (atleast can't change anything from here) 3. Pulse Audio Volume Control installed and has 100% volume (under Input devices) I can record the sound clip and it's barely audible. If I set to 150% gain in Pulse Audio Volume Control, its acceptable and others can hear over meetings. Can anyone please tell me how do I fix this? Everyone suggests using USB audio and with USB audio, it's pretty much same state. If I use Logitech Webcam USB Audio for recording, everything works so smooth and recorded audio is on-par with expectations. Based on 2, 3 - I don't think I have any other hardware issue than most likely Linux audio mess. Because I can increase the mic volume for Logitech in Alsamixer but not for HyperX Duocast. I noticed following details ``` Control: name="PCM Playback Volume", index=0 Info: id=8, control=2, cmask=0x3, channels=2, type="S16" Volume: min=-10240, max=-1536, dBmin=-4000, dBmax=-600 ``` Alsa info: [alsa-info.txt](https://github.com/alsa-project/alsa-ucm-conf/files/11329890… Issue URL : https://github.com/alsa-project/alsa-ucm-conf/issues/308 Repository URL: https://github.com/alsa-project/alsa-ucm-conf

1 0

[PATCH v2] ALSA: hda: Glenfly: add HD Audio PCI IDs and HDMI Codec Vendor IDs.
by Reaper Li 26 Apr '23

26 Apr '23

From: jasontao <jasontao(a)glenfly.com> Add a set of HD Audio PCI IDS, and the HDMI codec vendor IDs for Glenfly Gpus. - In default_bdl_pos_adj, set bdl to 128 as Glenfly Gpus have hardware limitation, need to increase hdac interrupt interval. - In azx_first_init, enable polling mode for Glenfly Gpu. When the codec complete the command, it sends interrupt and writes response entries to memory, howerver, the write requests sometimes are not actually synchronized to memory when driver handle hdac interrupt on Glenfly Gpus. If the RIRB status is not updated in the interrupt handler, azx_rirb_get_response keeps trying to recevie a response from rirb until 1s timeout. Enabling polling mode for Glenfly Gpu can fix the issue. - In patch_gf_hdmi, set Glenlfy Gpu Codec's no_sticky_stream as it need driver to do actual clean-ups for the linked codec when switch from one codec to another. Signed-off-by: jasontao <jasontao(a)glenfly.com> Signed-off-by: Reaper Li <reaperlioc(a)glenfly.com> --- v2: add some comments for code and details in the commit log. sound/pci/hda/hda_intel.c | 17 +++++++++++++++++ sound/pci/hda/patch_hdmi.c | 20 ++++++++++++++++++++ 2 files changed, 37 insertions(+) diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c index 77a592f21..0d6bf3ac6 100644 --- a/sound/pci/hda/hda_intel.c +++ b/sound/pci/hda/hda_intel.c @@ -227,6 +227,7 @@ enum { AZX_DRIVER_ATI, AZX_DRIVER_ATIHDMI, AZX_DRIVER_ATIHDMI_NS, + AZX_DRIVER_GFHDMI, AZX_DRIVER_VIA, AZX_DRIVER_SIS, AZX_DRIVER_ULI, @@ -349,6 +350,7 @@ static const char * const driver_short_names[] = { [AZX_DRIVER_ATI] = "HDA ATI SB", [AZX_DRIVER_ATIHDMI] = "HDA ATI HDMI", [AZX_DRIVER_ATIHDMI_NS] = "HDA ATI HDMI", + [AZX_DRIVER_GFHDMI] = "HDA GF HDMI", [AZX_DRIVER_VIA] = "HDA VIA VT82xx", [AZX_DRIVER_SIS] = "HDA SIS966", [AZX_DRIVER_ULI] = "HDA ULI M5461", @@ -1743,6 +1745,10 @@ static int default_bdl_pos_adj(struct azx *chip) } switch (chip->driver_type) { + /* increase the bdl size for Glenfly Gpus for hardware + * limitation on hdac interrupt interval */ + case AZX_DRIVER_GFHDMI: + return 128; case AZX_DRIVER_ICH: case AZX_DRIVER_PCH: return 1; @@ -1858,6 +1864,10 @@ static int azx_first_init(struct azx *chip) pci_write_config_dword(pci, PCI_BASE_ADDRESS_1, 0); } #endif + /* Fix reponse write request not synced to memory when handle + * hdac interrupt on Glenfly Gpus */ + if (chip->driver_type == AZX_DRIVER_GFHDMI) + bus->polling_mode = 1; err = pcim_iomap_regions(pci, 1 << 0, "ICH HD audio"); if (err < 0) @@ -1959,6 +1969,7 @@ static int azx_first_init(struct azx *chip) chip->playback_streams = ATIHDMI_NUM_PLAYBACK; chip->capture_streams = ATIHDMI_NUM_CAPTURE; break; + case AZX_DRIVER_GFHDMI: case AZX_DRIVER_GENERIC: default: chip->playback_streams = ICH6_NUM_PLAYBACK; @@ -2724,6 +2735,12 @@ static const struct pci_device_id azx_ids[] = { { PCI_DEVICE(0x1002, 0xab38), .driver_data = AZX_DRIVER_ATIHDMI_NS | AZX_DCAPS_PRESET_ATI_HDMI_NS | AZX_DCAPS_PM_RUNTIME }, + /* GLENFLY */ + { PCI_DEVICE(0x6766, PCI_ANY_ID), + .class = PCI_CLASS_MULTIMEDIA_HD_AUDIO << 8, + .class_mask = 0xffffff, + .driver_data = AZX_DRIVER_GFHDMI | AZX_DCAPS_POSFIX_LPIB | + AZX_DCAPS_NO_MSI | AZX_DCAPS_NO_64BIT }, /* VIA VT8251/VT8237A */ { PCI_DEVICE(0x1106, 0x3288), .driver_data = AZX_DRIVER_VIA }, /* VIA GFX VT7122/VX900 */ diff --git a/sound/pci/hda/patch_hdmi.c b/sound/pci/hda/patch_hdmi.c index 4ffa3a59f..03197abda 100644 --- a/sound/pci/hda/patch_hdmi.c +++ b/sound/pci/hda/patch_hdmi.c @@ -4489,6 +4489,20 @@ static int patch_via_hdmi(struct hda_codec *codec) return patch_simple_hdmi(codec, VIAHDMI_CVT_NID, VIAHDMI_PIN_NID); } +static int patch_gf_hdmi(struct hda_codec *codec) +{ + int err; + + err = patch_generic_hdmi(codec); + if (err) + return err; + + /* Glenfly GPUs have two codecs, stream switches from one codec to + * another, need to do actual clean-ups in codec_cleanup_stream */ + codec->no_sticky_stream = 1; + return 0; +} + /* * patch entries */ @@ -4579,6 +4593,12 @@ HDA_CODEC_ENTRY(0x10de009f, "GPU 9f HDMI/DP", patch_nvhdmi), HDA_CODEC_ENTRY(0x10de00a0, "GPU a0 HDMI/DP", patch_nvhdmi), HDA_CODEC_ENTRY(0x10de8001, "MCP73 HDMI", patch_nvhdmi_2ch), HDA_CODEC_ENTRY(0x10de8067, "MCP67/68 HDMI", patch_nvhdmi_2ch), +HDA_CODEC_ENTRY(0x67663d82, "Arise 82 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d83, "Arise 83 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d84, "Arise 84 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d85, "Arise 85 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d86, "Arise 86 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d87, "Arise 87 HDMI/DP", patch_gf_hdmi), HDA_CODEC_ENTRY(0x11069f80, "VX900 HDMI/DP", patch_via_hdmi), HDA_CODEC_ENTRY(0x11069f81, "VX900 HDMI/DP", patch_via_hdmi), HDA_CODEC_ENTRY(0x11069f84, "VX11 HDMI/DP", patch_generic_hdmi), -- 2.20.1

3 2

[PATCH v1] ASoC: Switch i2c drivers back to use .probe()
by Uwe Kleine-König 25 Apr '23

25 Apr '23

After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new() call-back type"), all drivers being converted to .probe_new() and then 03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert back to (the new) .probe() to be able to eventually drop .probe_new() from struct i2c_driver. Signed-off-by: Uwe Kleine-König <u.kleine-koenig(a)pengutronix.de> --- Hello, apart from some handish tweaking to keep the indention style this patch was generated using coccinelle. I kept it simple this time and didn't split by driver and didn't Cc the individual maintainers. If you prefer it differently, just say so. Best regards Uwe sound/soc/codecs/ad193x-i2c.c | 2 +- sound/soc/codecs/adau1372-i2c.c | 2 +- sound/soc/codecs/adau1373.c | 2 +- sound/soc/codecs/adau1701.c | 2 +- sound/soc/codecs/adau1761-i2c.c | 2 +- sound/soc/codecs/adau1781-i2c.c | 2 +- sound/soc/codecs/adau1977-i2c.c | 2 +- sound/soc/codecs/adau7118-i2c.c | 2 +- sound/soc/codecs/adav803.c | 2 +- sound/soc/codecs/ak4118.c | 2 +- sound/soc/codecs/ak4375.c | 2 +- sound/soc/codecs/ak4458.c | 2 +- sound/soc/codecs/ak4535.c | 2 +- sound/soc/codecs/ak4613.c | 2 +- sound/soc/codecs/ak4641.c | 2 +- sound/soc/codecs/ak4642.c | 2 +- sound/soc/codecs/ak4671.c | 2 +- sound/soc/codecs/ak5558.c | 2 +- sound/soc/codecs/alc5623.c | 2 +- sound/soc/codecs/alc5632.c | 2 +- sound/soc/codecs/aw88395/aw88395.c | 2 +- sound/soc/codecs/cs35l32.c | 2 +- sound/soc/codecs/cs35l33.c | 2 +- sound/soc/codecs/cs35l34.c | 2 +- sound/soc/codecs/cs35l35.c | 2 +- sound/soc/codecs/cs35l36.c | 2 +- sound/soc/codecs/cs35l41-i2c.c | 2 +- sound/soc/codecs/cs35l45-i2c.c | 2 +- sound/soc/codecs/cs4234.c | 2 +- sound/soc/codecs/cs4265.c | 2 +- sound/soc/codecs/cs4270.c | 2 +- sound/soc/codecs/cs4271-i2c.c | 2 +- sound/soc/codecs/cs42l42-i2c.c | 2 +- sound/soc/codecs/cs42l51-i2c.c | 2 +- sound/soc/codecs/cs42l52.c | 2 +- sound/soc/codecs/cs42l56.c | 2 +- sound/soc/codecs/cs42l73.c | 2 +- sound/soc/codecs/cs42l83-i2c.c | 2 +- sound/soc/codecs/cs42xx8-i2c.c | 2 +- sound/soc/codecs/cs43130.c | 2 +- sound/soc/codecs/cs4341.c | 2 +- sound/soc/codecs/cs4349.c | 2 +- sound/soc/codecs/cs53l30.c | 2 +- sound/soc/codecs/cx2072x.c | 2 +- sound/soc/codecs/da7210.c | 2 +- sound/soc/codecs/da7213.c | 2 +- sound/soc/codecs/da7218.c | 2 +- sound/soc/codecs/da7219.c | 2 +- sound/soc/codecs/da732x.c | 2 +- sound/soc/codecs/da9055.c | 2 +- sound/soc/codecs/es8316.c | 2 +- sound/soc/codecs/es8326.c | 2 +- sound/soc/codecs/es8328-i2c.c | 2 +- sound/soc/codecs/isabelle.c | 2 +- sound/soc/codecs/lm4857.c | 2 +- sound/soc/codecs/lm49453.c | 2 +- sound/soc/codecs/max9768.c | 2 +- sound/soc/codecs/max98088.c | 2 +- sound/soc/codecs/max98090.c | 2 +- sound/soc/codecs/max98095.c | 2 +- sound/soc/codecs/max98371.c | 2 +- sound/soc/codecs/max98373-i2c.c | 2 +- sound/soc/codecs/max98390.c | 2 +- sound/soc/codecs/max98396.c | 2 +- sound/soc/codecs/max9850.c | 2 +- sound/soc/codecs/max98504.c | 2 +- sound/soc/codecs/max98520.c | 2 +- sound/soc/codecs/max9860.c | 2 +- sound/soc/codecs/max9867.c | 2 +- sound/soc/codecs/max9877.c | 2 +- sound/soc/codecs/max98925.c | 2 +- sound/soc/codecs/max98926.c | 2 +- sound/soc/codecs/max98927.c | 2 +- sound/soc/codecs/ml26124.c | 2 +- sound/soc/codecs/mt6660.c | 2 +- sound/soc/codecs/nau8540.c | 2 +- sound/soc/codecs/nau8810.c | 2 +- sound/soc/codecs/nau8821.c | 2 +- sound/soc/codecs/nau8822.c | 2 +- sound/soc/codecs/nau8824.c | 2 +- sound/soc/codecs/nau8825.c | 2 +- sound/soc/codecs/pcm1681.c | 2 +- sound/soc/codecs/pcm1789-i2c.c | 2 +- sound/soc/codecs/pcm179x-i2c.c | 2 +- sound/soc/codecs/pcm186x-i2c.c | 2 +- sound/soc/codecs/pcm3060-i2c.c | 2 +- sound/soc/codecs/pcm3168a-i2c.c | 2 +- sound/soc/codecs/pcm512x-i2c.c | 2 +- sound/soc/codecs/rt1011.c | 2 +- sound/soc/codecs/rt1015.c | 2 +- sound/soc/codecs/rt1016.c | 2 +- sound/soc/codecs/rt1019.c | 2 +- sound/soc/codecs/rt1305.c | 2 +- sound/soc/codecs/rt1308.c | 2 +- sound/soc/codecs/rt274.c | 2 +- sound/soc/codecs/rt286.c | 2 +- sound/soc/codecs/rt298.c | 2 +- sound/soc/codecs/rt5514.c | 2 +- sound/soc/codecs/rt5616.c | 2 +- sound/soc/codecs/rt5631.c | 2 +- sound/soc/codecs/rt5640.c | 2 +- sound/soc/codecs/rt5645.c | 2 +- sound/soc/codecs/rt5651.c | 2 +- sound/soc/codecs/rt5659.c | 2 +- sound/soc/codecs/rt5660.c | 2 +- sound/soc/codecs/rt5663.c | 2 +- sound/soc/codecs/rt5665.c | 2 +- sound/soc/codecs/rt5668.c | 2 +- sound/soc/codecs/rt5670.c | 2 +- sound/soc/codecs/rt5677.c | 2 +- sound/soc/codecs/rt5682-i2c.c | 2 +- sound/soc/codecs/rt5682s.c | 2 +- sound/soc/codecs/rt9120.c | 2 +- sound/soc/codecs/sgtl5000.c | 2 +- sound/soc/codecs/sma1303.c | 2 +- sound/soc/codecs/src4xxx-i2c.c | 2 +- sound/soc/codecs/ssm2518.c | 2 +- sound/soc/codecs/ssm2602-i2c.c | 2 +- sound/soc/codecs/ssm4567.c | 2 +- sound/soc/codecs/sta32x.c | 2 +- sound/soc/codecs/sta350.c | 2 +- sound/soc/codecs/sta529.c | 2 +- sound/soc/codecs/tas2552.c | 2 +- sound/soc/codecs/tas2562.c | 2 +- sound/soc/codecs/tas2764.c | 2 +- sound/soc/codecs/tas2770.c | 2 +- sound/soc/codecs/tas2780.c | 2 +- sound/soc/codecs/tas5086.c | 2 +- sound/soc/codecs/tas571x.c | 2 +- sound/soc/codecs/tas5720.c | 2 +- sound/soc/codecs/tas5805m.c | 2 +- sound/soc/codecs/tas6424.c | 2 +- sound/soc/codecs/tda7419.c | 2 +- sound/soc/codecs/tfa9879.c | 2 +- sound/soc/codecs/tfa989x.c | 2 +- sound/soc/codecs/tlv320adc3xxx.c | 2 +- sound/soc/codecs/tlv320adcx140.c | 2 +- sound/soc/codecs/tlv320aic23-i2c.c | 2 +- sound/soc/codecs/tlv320aic31xx.c | 2 +- sound/soc/codecs/tlv320aic32x4-i2c.c | 2 +- sound/soc/codecs/tlv320aic3x-i2c.c | 2 +- sound/soc/codecs/tlv320dac33.c | 2 +- sound/soc/codecs/tpa6130a2.c | 2 +- sound/soc/codecs/ts3a227e.c | 2 +- sound/soc/codecs/tscs42xx.c | 2 +- sound/soc/codecs/tscs454.c | 2 +- sound/soc/codecs/uda1380.c | 2 +- sound/soc/codecs/wm1250-ev1.c | 2 +- sound/soc/codecs/wm2000.c | 2 +- sound/soc/codecs/wm2200.c | 2 +- sound/soc/codecs/wm5100.c | 2 +- sound/soc/codecs/wm8510.c | 2 +- sound/soc/codecs/wm8523.c | 2 +- sound/soc/codecs/wm8580.c | 2 +- sound/soc/codecs/wm8711.c | 2 +- sound/soc/codecs/wm8728.c | 2 +- sound/soc/codecs/wm8731-i2c.c | 2 +- sound/soc/codecs/wm8737.c | 2 +- sound/soc/codecs/wm8741.c | 2 +- sound/soc/codecs/wm8750.c | 2 +- sound/soc/codecs/wm8753.c | 2 +- sound/soc/codecs/wm8776.c | 2 +- sound/soc/codecs/wm8804-i2c.c | 2 +- sound/soc/codecs/wm8900.c | 2 +- sound/soc/codecs/wm8903.c | 2 +- sound/soc/codecs/wm8904.c | 2 +- sound/soc/codecs/wm8940.c | 2 +- sound/soc/codecs/wm8955.c | 2 +- sound/soc/codecs/wm8960.c | 2 +- sound/soc/codecs/wm8961.c | 2 +- sound/soc/codecs/wm8962.c | 2 +- sound/soc/codecs/wm8971.c | 2 +- sound/soc/codecs/wm8974.c | 2 +- sound/soc/codecs/wm8978.c | 2 +- sound/soc/codecs/wm8983.c | 2 +- sound/soc/codecs/wm8985.c | 2 +- sound/soc/codecs/wm8988.c | 2 +- sound/soc/codecs/wm8990.c | 2 +- sound/soc/codecs/wm8991.c | 2 +- sound/soc/codecs/wm8993.c | 2 +- sound/soc/codecs/wm8995.c | 2 +- sound/soc/codecs/wm8996.c | 2 +- sound/soc/codecs/wm9081.c | 2 +- sound/soc/codecs/wm9090.c | 2 +- 184 files changed, 184 insertions(+), 184 deletions(-) diff --git a/sound/soc/codecs/ad193x-i2c.c b/sound/soc/codecs/ad193x-i2c.c index 4cb8d87f9011..15d74bb31c4c 100644 --- a/sound/soc/codecs/ad193x-i2c.c +++ b/sound/soc/codecs/ad193x-i2c.c @@ -38,7 +38,7 @@ static struct i2c_driver ad193x_i2c_driver = { .driver = { .name = "ad193x", }, - .probe_new = ad193x_i2c_probe, + .probe = ad193x_i2c_probe, .id_table = ad193x_id, }; module_i2c_driver(ad193x_i2c_driver); diff --git a/sound/soc/codecs/adau1372-i2c.c b/sound/soc/codecs/adau1372-i2c.c index 8ed0ffdedbc9..132b9e2cca59 100644 --- a/sound/soc/codecs/adau1372-i2c.c +++ b/sound/soc/codecs/adau1372-i2c.c @@ -30,7 +30,7 @@ static struct i2c_driver adau1372_i2c_driver = { .driver = { .name = "adau1372", }, - .probe_new = adau1372_i2c_probe, + .probe = adau1372_i2c_probe, .id_table = adau1372_i2c_ids, }; module_i2c_driver(adau1372_i2c_driver); diff --git a/sound/soc/codecs/adau1373.c b/sound/soc/codecs/adau1373.c index 37e178e8a1d0..c5b087b8fffc 100644 --- a/sound/soc/codecs/adau1373.c +++ b/sound/soc/codecs/adau1373.c @@ -1505,7 +1505,7 @@ static struct i2c_driver adau1373_i2c_driver = { .driver = { .name = "adau1373", }, - .probe_new = adau1373_i2c_probe, + .probe = adau1373_i2c_probe, .id_table = adau1373_i2c_id, }; diff --git a/sound/soc/codecs/adau1701.c b/sound/soc/codecs/adau1701.c index 135a7db7fcf9..8c8de3b3c901 100644 --- a/sound/soc/codecs/adau1701.c +++ b/sound/soc/codecs/adau1701.c @@ -876,7 +876,7 @@ static struct i2c_driver adau1701_i2c_driver = { .name = "adau1701", .of_match_table = of_match_ptr(adau1701_dt_ids), }, - .probe_new = adau1701_i2c_probe, + .probe = adau1701_i2c_probe, .id_table = adau1701_i2c_id, }; diff --git a/sound/soc/codecs/adau1761-i2c.c b/sound/soc/codecs/adau1761-i2c.c index 0cefff49569c..a554255186ae 100644 --- a/sound/soc/codecs/adau1761-i2c.c +++ b/sound/soc/codecs/adau1761-i2c.c @@ -60,7 +60,7 @@ static struct i2c_driver adau1761_i2c_driver = { .name = "adau1761", .of_match_table = of_match_ptr(adau1761_i2c_dt_ids), }, - .probe_new = adau1761_i2c_probe, + .probe = adau1761_i2c_probe, .remove = adau1761_i2c_remove, .id_table = adau1761_i2c_ids, }; diff --git a/sound/soc/codecs/adau1781-i2c.c b/sound/soc/codecs/adau1781-i2c.c index 39021b8cfb62..3a170fd78ff3 100644 --- a/sound/soc/codecs/adau1781-i2c.c +++ b/sound/soc/codecs/adau1781-i2c.c @@ -56,7 +56,7 @@ static struct i2c_driver adau1781_i2c_driver = { .name = "adau1781", .of_match_table = of_match_ptr(adau1781_i2c_dt_ids), }, - .probe_new = adau1781_i2c_probe, + .probe = adau1781_i2c_probe, .remove = adau1781_i2c_remove, .id_table = adau1781_i2c_ids, }; diff --git a/sound/soc/codecs/adau1977-i2c.c b/sound/soc/codecs/adau1977-i2c.c index 9f137a0634d5..24c7b9c84c19 100644 --- a/sound/soc/codecs/adau1977-i2c.c +++ b/sound/soc/codecs/adau1977-i2c.c @@ -42,7 +42,7 @@ static struct i2c_driver adau1977_i2c_driver = { .driver = { .name = "adau1977", }, - .probe_new = adau1977_i2c_probe, + .probe = adau1977_i2c_probe, .id_table = adau1977_i2c_ids, }; module_i2c_driver(adau1977_i2c_driver); diff --git a/sound/soc/codecs/adau7118-i2c.c b/sound/soc/codecs/adau7118-i2c.c index afed48401b25..73f181f7757e 100644 --- a/sound/soc/codecs/adau7118-i2c.c +++ b/sound/soc/codecs/adau7118-i2c.c @@ -78,7 +78,7 @@ static struct i2c_driver adau7118_driver = { .name = "adau7118", .of_match_table = adau7118_of_match, }, - .probe_new = adau7118_probe_i2c, + .probe = adau7118_probe_i2c, .id_table = adau7118_id, }; module_i2c_driver(adau7118_driver); diff --git a/sound/soc/codecs/adav803.c b/sound/soc/codecs/adav803.c index bf181bbaabed..78a317947df9 100644 --- a/sound/soc/codecs/adav803.c +++ b/sound/soc/codecs/adav803.c @@ -29,7 +29,7 @@ static struct i2c_driver adav803_driver = { .driver = { .name = "adav803", }, - .probe_new = adav803_probe, + .probe = adav803_probe, .id_table = adav803_id, }; module_i2c_driver(adav803_driver); diff --git a/sound/soc/codecs/ak4118.c b/sound/soc/codecs/ak4118.c index b6d9a10bdccd..ebcdc412e39c 100644 --- a/sound/soc/codecs/ak4118.c +++ b/sound/soc/codecs/ak4118.c @@ -414,7 +414,7 @@ static struct i2c_driver ak4118_i2c_driver = { .of_match_table = of_match_ptr(ak4118_of_match), }, .id_table = ak4118_id_table, - .probe_new = ak4118_i2c_probe, + .probe = ak4118_i2c_probe, }; module_i2c_driver(ak4118_i2c_driver); diff --git a/sound/soc/codecs/ak4375.c b/sound/soc/codecs/ak4375.c index 573389e402f8..f287acb98646 100644 --- a/sound/soc/codecs/ak4375.c +++ b/sound/soc/codecs/ak4375.c @@ -597,7 +597,7 @@ static struct i2c_driver ak4375_i2c_driver = { .pm = &ak4375_pm, .of_match_table = ak4375_of_match, }, - .probe_new = ak4375_i2c_probe, + .probe = ak4375_i2c_probe, .remove = ak4375_i2c_remove, }; module_i2c_driver(ak4375_i2c_driver); diff --git a/sound/soc/codecs/ak4458.c b/sound/soc/codecs/ak4458.c index 8c69c8cf9b67..77678f85ad94 100644 --- a/sound/soc/codecs/ak4458.c +++ b/sound/soc/codecs/ak4458.c @@ -818,7 +818,7 @@ static struct i2c_driver ak4458_i2c_driver = { .pm = &ak4458_pm, .of_match_table = ak4458_of_match, }, - .probe_new = ak4458_i2c_probe, + .probe = ak4458_i2c_probe, .remove = ak4458_i2c_remove, }; diff --git a/sound/soc/codecs/ak4535.c b/sound/soc/codecs/ak4535.c index 8c8c93eea704..904bf91090aa 100644 --- a/sound/soc/codecs/ak4535.c +++ b/sound/soc/codecs/ak4535.c @@ -439,7 +439,7 @@ static struct i2c_driver ak4535_i2c_driver = { .driver = { .name = "ak4535", }, - .probe_new = ak4535_i2c_probe, + .probe = ak4535_i2c_probe, .id_table = ak4535_i2c_id, }; diff --git a/sound/soc/codecs/ak4613.c b/sound/soc/codecs/ak4613.c index f75c19ef3551..ad56caec9dac 100644 --- a/sound/soc/codecs/ak4613.c +++ b/sound/soc/codecs/ak4613.c @@ -925,7 +925,7 @@ static struct i2c_driver ak4613_i2c_driver = { .name = "ak4613-codec", .of_match_table = ak4613_of_match, }, - .probe_new = ak4613_i2c_probe, + .probe = ak4613_i2c_probe, .id_table = ak4613_i2c_id, }; diff --git a/sound/soc/codecs/ak4641.c b/sound/soc/codecs/ak4641.c index 0d3ee195b3cc..5b7df2f0dd6a 100644 --- a/sound/soc/codecs/ak4641.c +++ b/sound/soc/codecs/ak4641.c @@ -628,7 +628,7 @@ static struct i2c_driver ak4641_i2c_driver = { .driver = { .name = "ak4641", }, - .probe_new = ak4641_i2c_probe, + .probe = ak4641_i2c_probe, .remove = ak4641_i2c_remove, .id_table = ak4641_i2c_id, }; diff --git a/sound/soc/codecs/ak4642.c b/sound/soc/codecs/ak4642.c index 914d5b1969f8..2a8984c1fa9c 100644 --- a/sound/soc/codecs/ak4642.c +++ b/sound/soc/codecs/ak4642.c @@ -698,7 +698,7 @@ static struct i2c_driver ak4642_i2c_driver = { .name = "ak4642-codec", .of_match_table = ak4642_of_match, }, - .probe_new = ak4642_i2c_probe, + .probe = ak4642_i2c_probe, .id_table = ak4642_i2c_id, }; diff --git a/sound/soc/codecs/ak4671.c b/sound/soc/codecs/ak4671.c index cd76765f8cc0..5b849b390c2a 100644 --- a/sound/soc/codecs/ak4671.c +++ b/sound/soc/codecs/ak4671.c @@ -655,7 +655,7 @@ static struct i2c_driver ak4671_i2c_driver = { .driver = { .name = "ak4671-codec", }, - .probe_new = ak4671_i2c_probe, + .probe = ak4671_i2c_probe, .id_table = ak4671_i2c_id, }; diff --git a/sound/soc/codecs/ak5558.c b/sound/soc/codecs/ak5558.c index 60abcffe6a0c..442e2cb42df4 100644 --- a/sound/soc/codecs/ak5558.c +++ b/sound/soc/codecs/ak5558.c @@ -497,7 +497,7 @@ static struct i2c_driver ak5558_i2c_driver = { .of_match_table = of_match_ptr(ak5558_i2c_dt_ids), .pm = &ak5558_pm, }, - .probe_new = ak5558_i2c_probe, + .probe = ak5558_i2c_probe, .remove = ak5558_i2c_remove, }; diff --git a/sound/soc/codecs/alc5623.c b/sound/soc/codecs/alc5623.c index 9ef01b1dd294..b24c32206884 100644 --- a/sound/soc/codecs/alc5623.c +++ b/sound/soc/codecs/alc5623.c @@ -1083,7 +1083,7 @@ static struct i2c_driver alc5623_i2c_driver = { .name = "alc562x-codec", .of_match_table = of_match_ptr(alc5623_of_match), }, - .probe_new = alc5623_i2c_probe, + .probe = alc5623_i2c_probe, .id_table = alc5623_i2c_table, }; diff --git a/sound/soc/codecs/alc5632.c b/sound/soc/codecs/alc5632.c index a770704a4e17..d5021f266930 100644 --- a/sound/soc/codecs/alc5632.c +++ b/sound/soc/codecs/alc5632.c @@ -1182,7 +1182,7 @@ static struct i2c_driver alc5632_i2c_driver = { .name = "alc5632", .of_match_table = of_match_ptr(alc5632_of_match), }, - .probe_new = alc5632_i2c_probe, + .probe = alc5632_i2c_probe, .id_table = alc5632_i2c_table, }; diff --git a/sound/soc/codecs/aw88395/aw88395.c b/sound/soc/codecs/aw88395/aw88395.c index afdce6b7fa26..9dcd75dd799a 100644 --- a/sound/soc/codecs/aw88395/aw88395.c +++ b/sound/soc/codecs/aw88395/aw88395.c @@ -570,7 +570,7 @@ static struct i2c_driver aw88395_i2c_driver = { .driver = { .name = AW88395_I2C_NAME, }, - .probe_new = aw88395_i2c_probe, + .probe = aw88395_i2c_probe, .id_table = aw88395_i2c_id, }; module_i2c_driver(aw88395_i2c_driver); diff --git a/sound/soc/codecs/cs35l32.c b/sound/soc/codecs/cs35l32.c index dc7a58d68076..88828714c5d6 100644 --- a/sound/soc/codecs/cs35l32.c +++ b/sound/soc/codecs/cs35l32.c @@ -572,7 +572,7 @@ static struct i2c_driver cs35l32_i2c_driver = { .of_match_table = cs35l32_of_match, }, .id_table = cs35l32_id, - .probe_new = cs35l32_i2c_probe, + .probe = cs35l32_i2c_probe, .remove = cs35l32_i2c_remove, }; diff --git a/sound/soc/codecs/cs35l33.c b/sound/soc/codecs/cs35l33.c index 15e79168d256..33552414e9f1 100644 --- a/sound/soc/codecs/cs35l33.c +++ b/sound/soc/codecs/cs35l33.c @@ -1282,7 +1282,7 @@ static struct i2c_driver cs35l33_i2c_driver = { }, .id_table = cs35l33_id, - .probe_new = cs35l33_i2c_probe, + .probe = cs35l33_i2c_probe, .remove = cs35l33_i2c_remove, }; diff --git a/sound/soc/codecs/cs35l34.c b/sound/soc/codecs/cs35l34.c index b3f98023e6a7..5ef3fc453391 100644 --- a/sound/soc/codecs/cs35l34.c +++ b/sound/soc/codecs/cs35l34.c @@ -1213,7 +1213,7 @@ static struct i2c_driver cs35l34_i2c_driver = { }, .id_table = cs35l34_id, - .probe_new = cs35l34_i2c_probe, + .probe = cs35l34_i2c_probe, .remove = cs35l34_i2c_remove, }; diff --git a/sound/soc/codecs/cs35l35.c b/sound/soc/codecs/cs35l35.c index 947a440a3a47..2e3bb61a2bf4 100644 --- a/sound/soc/codecs/cs35l35.c +++ b/sound/soc/codecs/cs35l35.c @@ -1654,7 +1654,7 @@ static struct i2c_driver cs35l35_i2c_driver = { .of_match_table = cs35l35_of_match, }, .id_table = cs35l35_id, - .probe_new = cs35l35_i2c_probe, + .probe = cs35l35_i2c_probe, .remove = cs35l35_i2c_remove, }; diff --git a/sound/soc/codecs/cs35l36.c b/sound/soc/codecs/cs35l36.c index a078dd422ea1..04ba7f25012e 100644 --- a/sound/soc/codecs/cs35l36.c +++ b/sound/soc/codecs/cs35l36.c @@ -1944,7 +1944,7 @@ static struct i2c_driver cs35l36_i2c_driver = { .of_match_table = cs35l36_of_match, }, .id_table = cs35l36_id, - .probe_new = cs35l36_i2c_probe, + .probe = cs35l36_i2c_probe, .remove = cs35l36_i2c_remove, }; module_i2c_driver(cs35l36_i2c_driver); diff --git a/sound/soc/codecs/cs35l41-i2c.c b/sound/soc/codecs/cs35l41-i2c.c index 3676b596f60b..7ea890d7d387 100644 --- a/sound/soc/codecs/cs35l41-i2c.c +++ b/sound/soc/codecs/cs35l41-i2c.c @@ -88,7 +88,7 @@ static struct i2c_driver cs35l41_i2c_driver = { .acpi_match_table = ACPI_PTR(cs35l41_acpi_match), }, .id_table = cs35l41_id_i2c, - .probe_new = cs35l41_i2c_probe, + .probe = cs35l41_i2c_probe, .remove = cs35l41_i2c_remove, }; diff --git a/sound/soc/codecs/cs35l45-i2c.c b/sound/soc/codecs/cs35l45-i2c.c index 1117df4b2f11..5173399e6d74 100644 --- a/sound/soc/codecs/cs35l45-i2c.c +++ b/sound/soc/codecs/cs35l45-i2c.c @@ -62,7 +62,7 @@ static struct i2c_driver cs35l45_i2c_driver = { .pm = &cs35l45_pm_ops, }, .id_table = cs35l45_id_i2c, - .probe_new = cs35l45_i2c_probe, + .probe = cs35l45_i2c_probe, .remove = cs35l45_i2c_remove, }; module_i2c_driver(cs35l45_i2c_driver); diff --git a/sound/soc/codecs/cs4234.c b/sound/soc/codecs/cs4234.c index dee1a6662c2e..2d53a440a107 100644 --- a/sound/soc/codecs/cs4234.c +++ b/sound/soc/codecs/cs4234.c @@ -906,7 +906,7 @@ static struct i2c_driver cs4234_i2c_driver = { .pm = &cs4234_pm, .of_match_table = cs4234_of_match, }, - .probe_new = cs4234_i2c_probe, + .probe = cs4234_i2c_probe, .remove = cs4234_i2c_remove, }; module_i2c_driver(cs4234_i2c_driver); diff --git a/sound/soc/codecs/cs4265.c b/sound/soc/codecs/cs4265.c index 3573363b7e31..0cfc5ab36a13 100644 --- a/sound/soc/codecs/cs4265.c +++ b/sound/soc/codecs/cs4265.c @@ -649,7 +649,7 @@ static struct i2c_driver cs4265_i2c_driver = { .of_match_table = cs4265_of_match, }, .id_table = cs4265_id, - .probe_new = cs4265_i2c_probe, + .probe = cs4265_i2c_probe, .remove = cs4265_i2c_remove, }; diff --git a/sound/soc/codecs/cs4270.c b/sound/soc/codecs/cs4270.c index 1b640d8232ba..ab32f15e3b44 100644 --- a/sound/soc/codecs/cs4270.c +++ b/sound/soc/codecs/cs4270.c @@ -751,7 +751,7 @@ static struct i2c_driver cs4270_i2c_driver = { .of_match_table = cs4270_of_match, }, .id_table = cs4270_id, - .probe_new = cs4270_i2c_probe, + .probe = cs4270_i2c_probe, .remove = cs4270_i2c_remove, }; diff --git a/sound/soc/codecs/cs4271-i2c.c b/sound/soc/codecs/cs4271-i2c.c index 0e8a7cf0da50..e106458465bf 100644 --- a/sound/soc/codecs/cs4271-i2c.c +++ b/sound/soc/codecs/cs4271-i2c.c @@ -34,7 +34,7 @@ static struct i2c_driver cs4271_i2c_driver = { .name = "cs4271", .of_match_table = of_match_ptr(cs4271_dt_ids), }, - .probe_new = cs4271_i2c_probe, + .probe = cs4271_i2c_probe, .id_table = cs4271_i2c_id, }; module_i2c_driver(cs4271_i2c_driver); diff --git a/sound/soc/codecs/cs42l42-i2c.c b/sound/soc/codecs/cs42l42-i2c.c index 67b253287daf..2552a1e6b82f 100644 --- a/sound/soc/codecs/cs42l42-i2c.c +++ b/sound/soc/codecs/cs42l42-i2c.c @@ -92,7 +92,7 @@ static struct i2c_driver cs42l42_i2c_driver = { .acpi_match_table = ACPI_PTR(cs42l42_acpi_match), }, .id_table = cs42l42_id, - .probe_new = cs42l42_i2c_probe, + .probe = cs42l42_i2c_probe, .remove = cs42l42_i2c_remove, }; diff --git a/sound/soc/codecs/cs42l51-i2c.c b/sound/soc/codecs/cs42l51-i2c.c index 85238339fbca..b2106ff6a7cb 100644 --- a/sound/soc/codecs/cs42l51-i2c.c +++ b/sound/soc/codecs/cs42l51-i2c.c @@ -43,7 +43,7 @@ static struct i2c_driver cs42l51_i2c_driver = { .of_match_table = cs42l51_of_match, .pm = &cs42l51_pm_ops, }, - .probe_new = cs42l51_i2c_probe, + .probe = cs42l51_i2c_probe, .remove = cs42l51_i2c_remove, .id_table = cs42l51_i2c_id, }; diff --git a/sound/soc/codecs/cs42l52.c b/sound/soc/codecs/cs42l52.c index 90bf535fc5a5..1f1ded0ff0ac 100644 --- a/sound/soc/codecs/cs42l52.c +++ b/sound/soc/codecs/cs42l52.c @@ -1226,7 +1226,7 @@ static struct i2c_driver cs42l52_i2c_driver = { .of_match_table = cs42l52_of_match, }, .id_table = cs42l52_id, - .probe_new = cs42l52_i2c_probe, + .probe = cs42l52_i2c_probe, }; module_i2c_driver(cs42l52_i2c_driver); diff --git a/sound/soc/codecs/cs42l56.c b/sound/soc/codecs/cs42l56.c index 3b0e715549c9..4c646e8d72aa 100644 --- a/sound/soc/codecs/cs42l56.c +++ b/sound/soc/codecs/cs42l56.c @@ -1341,7 +1341,7 @@ static struct i2c_driver cs42l56_i2c_driver = { .of_match_table = cs42l56_of_match, }, .id_table = cs42l56_id, - .probe_new = cs42l56_i2c_probe, + .probe = cs42l56_i2c_probe, .remove = cs42l56_i2c_remove, }; diff --git a/sound/soc/codecs/cs42l73.c b/sound/soc/codecs/cs42l73.c index 0a146319755a..378a4400d234 100644 --- a/sound/soc/codecs/cs42l73.c +++ b/sound/soc/codecs/cs42l73.c @@ -1384,7 +1384,7 @@ static struct i2c_driver cs42l73_i2c_driver = { .of_match_table = cs42l73_of_match, }, .id_table = cs42l73_id, - .probe_new = cs42l73_i2c_probe, + .probe = cs42l73_i2c_probe, }; diff --git a/sound/soc/codecs/cs42l83-i2c.c b/sound/soc/codecs/cs42l83-i2c.c index 37629ebd90e0..d3aa1edf60bb 100644 --- a/sound/soc/codecs/cs42l83-i2c.c +++ b/sound/soc/codecs/cs42l83-i2c.c @@ -228,7 +228,7 @@ static struct i2c_driver cs42l83_i2c_driver = { .pm = &cs42l83_i2c_pm_ops, .of_match_table = of_match_ptr(cs42l83_of_match), }, - .probe_new = cs42l83_i2c_probe, + .probe = cs42l83_i2c_probe, .remove = cs42l83_i2c_remove, }; diff --git a/sound/soc/codecs/cs42xx8-i2c.c b/sound/soc/codecs/cs42xx8-i2c.c index 052ffb7dcfc6..a422472820fb 100644 --- a/sound/soc/codecs/cs42xx8-i2c.c +++ b/sound/soc/codecs/cs42xx8-i2c.c @@ -70,7 +70,7 @@ static struct i2c_driver cs42xx8_i2c_driver = { .pm = &cs42xx8_pm, .of_match_table = cs42xx8_of_match, }, - .probe_new = cs42xx8_i2c_probe, + .probe = cs42xx8_i2c_probe, .remove = cs42xx8_i2c_remove, .id_table = cs42xx8_i2c_id, }; diff --git a/sound/soc/codecs/cs43130.c b/sound/soc/codecs/cs43130.c index db39abb2a31b..523ca54ebf64 100644 --- a/sound/soc/codecs/cs43130.c +++ b/sound/soc/codecs/cs43130.c @@ -2697,7 +2697,7 @@ static struct i2c_driver cs43130_i2c_driver = { .pm = &cs43130_runtime_pm, }, .id_table = cs43130_i2c_id, - .probe_new = cs43130_i2c_probe, + .probe = cs43130_i2c_probe, .remove = cs43130_i2c_remove, }; diff --git a/sound/soc/codecs/cs4341.c b/sound/soc/codecs/cs4341.c index ac1696034846..2ceca5d0e5bf 100644 --- a/sound/soc/codecs/cs4341.c +++ b/sound/soc/codecs/cs4341.c @@ -258,7 +258,7 @@ static struct i2c_driver cs4341_i2c_driver = { .name = "cs4341-i2c", .of_match_table = of_match_ptr(cs4341_dt_ids), }, - .probe_new = cs4341_i2c_probe, + .probe = cs4341_i2c_probe, .id_table = cs4341_i2c_id, }; #endif diff --git a/sound/soc/codecs/cs4349.c b/sound/soc/codecs/cs4349.c index ba94ffd0a7e4..8365dd0ebe2a 100644 --- a/sound/soc/codecs/cs4349.c +++ b/sound/soc/codecs/cs4349.c @@ -375,7 +375,7 @@ static struct i2c_driver cs4349_i2c_driver = { .pm = &cs4349_runtime_pm, }, .id_table = cs4349_i2c_id, - .probe_new = cs4349_i2c_probe, + .probe = cs4349_i2c_probe, .remove = cs4349_i2c_remove, }; diff --git a/sound/soc/codecs/cs53l30.c b/sound/soc/codecs/cs53l30.c index 69db0013d243..51ca66e7b3ea 100644 --- a/sound/soc/codecs/cs53l30.c +++ b/sound/soc/codecs/cs53l30.c @@ -1121,7 +1121,7 @@ static struct i2c_driver cs53l30_i2c_driver = { .pm = &cs53l30_runtime_pm, }, .id_table = cs53l30_id, - .probe_new = cs53l30_i2c_probe, + .probe = cs53l30_i2c_probe, .remove = cs53l30_i2c_remove, }; diff --git a/sound/soc/codecs/cx2072x.c b/sound/soc/codecs/cx2072x.c index 5deceaa89282..082231088a26 100644 --- a/sound/soc/codecs/cx2072x.c +++ b/sound/soc/codecs/cx2072x.c @@ -1706,7 +1706,7 @@ static struct i2c_driver cx2072x_i2c_driver = { .acpi_match_table = ACPI_PTR(cx2072x_acpi_match), .pm = &cx2072x_runtime_pm, }, - .probe_new = cx2072x_i2c_probe, + .probe = cx2072x_i2c_probe, .remove = cx2072x_i2c_remove, .id_table = cx2072x_i2c_id, }; diff --git a/sound/soc/codecs/da7210.c b/sound/soc/codecs/da7210.c index f838466bfebf..1e232d01809c 100644 --- a/sound/soc/codecs/da7210.c +++ b/sound/soc/codecs/da7210.c @@ -1248,7 +1248,7 @@ static struct i2c_driver da7210_i2c_driver = { .driver = { .name = "da7210", }, - .probe_new = da7210_i2c_probe, + .probe = da7210_i2c_probe, .id_table = da7210_i2c_id, }; #endif diff --git a/sound/soc/codecs/da7213.c b/sound/soc/codecs/da7213.c index 1c1f211a8e2e..3a6449c44b23 100644 --- a/sound/soc/codecs/da7213.c +++ b/sound/soc/codecs/da7213.c @@ -2069,7 +2069,7 @@ static struct i2c_driver da7213_i2c_driver = { .acpi_match_table = ACPI_PTR(da7213_acpi_match), .pm = &da7213_pm, }, - .probe_new = da7213_i2c_probe, + .probe = da7213_i2c_probe, .remove = da7213_i2c_remove, .id_table = da7213_i2c_id, }; diff --git a/sound/soc/codecs/da7218.c b/sound/soc/codecs/da7218.c index 91372909d184..6d2cc9260b93 100644 --- a/sound/soc/codecs/da7218.c +++ b/sound/soc/codecs/da7218.c @@ -3321,7 +3321,7 @@ static struct i2c_driver da7218_i2c_driver = { .name = "da7218", .of_match_table = da7218_of_match, }, - .probe_new = da7218_i2c_probe, + .probe = da7218_i2c_probe, .id_table = da7218_i2c_id, }; diff --git a/sound/soc/codecs/da7219.c b/sound/soc/codecs/da7219.c index 7468ee4af2ea..600c2db58756 100644 --- a/sound/soc/codecs/da7219.c +++ b/sound/soc/codecs/da7219.c @@ -2714,7 +2714,7 @@ static struct i2c_driver da7219_i2c_driver = { .of_match_table = of_match_ptr(da7219_of_match), .acpi_match_table = ACPI_PTR(da7219_acpi_match), }, - .probe_new = da7219_i2c_probe, + .probe = da7219_i2c_probe, .id_table = da7219_i2c_id, }; diff --git a/sound/soc/codecs/da732x.c b/sound/soc/codecs/da732x.c index 2c5b0b74201c..f8ca1afa8af5 100644 --- a/sound/soc/codecs/da732x.c +++ b/sound/soc/codecs/da732x.c @@ -1555,7 +1555,7 @@ static struct i2c_driver da732x_i2c_driver = { .driver = { .name = "da7320", }, - .probe_new = da732x_i2c_probe, + .probe = da732x_i2c_probe, .id_table = da732x_i2c_id, }; diff --git a/sound/soc/codecs/da9055.c b/sound/soc/codecs/da9055.c index 28043b4530df..ae20086777b5 100644 --- a/sound/soc/codecs/da9055.c +++ b/sound/soc/codecs/da9055.c @@ -1531,7 +1531,7 @@ static struct i2c_driver da9055_i2c_driver = { .name = "da9055-codec", .of_match_table = of_match_ptr(da9055_of_match), }, - .probe_new = da9055_i2c_probe, + .probe = da9055_i2c_probe, .id_table = da9055_i2c_id, }; diff --git a/sound/soc/codecs/es8316.c b/sound/soc/codecs/es8316.c index 056c3082fe02..4b1f8b808b28 100644 --- a/sound/soc/codecs/es8316.c +++ b/sound/soc/codecs/es8316.c @@ -884,7 +884,7 @@ static struct i2c_driver es8316_i2c_driver = { .acpi_match_table = ACPI_PTR(es8316_acpi_match), .of_match_table = of_match_ptr(es8316_of_match), }, - .probe_new = es8316_i2c_probe, + .probe = es8316_i2c_probe, .id_table = es8316_i2c_id, }; module_i2c_driver(es8316_i2c_driver); diff --git a/sound/soc/codecs/es8326.c b/sound/soc/codecs/es8326.c index 28a0565c2a95..7cb5b57ae655 100644 --- a/sound/soc/codecs/es8326.c +++ b/sound/soc/codecs/es8326.c @@ -896,7 +896,7 @@ static struct i2c_driver es8326_i2c_driver = { .acpi_match_table = ACPI_PTR(es8326_acpi_match), .of_match_table = of_match_ptr(es8326_of_match), }, - .probe_new = es8326_i2c_probe, + .probe = es8326_i2c_probe, .id_table = es8326_i2c_id, }; module_i2c_driver(es8326_i2c_driver); diff --git a/sound/soc/codecs/es8328-i2c.c b/sound/soc/codecs/es8328-i2c.c index 68072e99fcc7..3c4aaa0032a0 100644 --- a/sound/soc/codecs/es8328-i2c.c +++ b/sound/soc/codecs/es8328-i2c.c @@ -40,7 +40,7 @@ static struct i2c_driver es8328_i2c_driver = { .name = "es8328", .of_match_table = es8328_of_match, }, - .probe_new = es8328_i2c_probe, + .probe = es8328_i2c_probe, .id_table = es8328_id, }; diff --git a/sound/soc/codecs/isabelle.c b/sound/soc/codecs/isabelle.c index 50105d72b2b7..f9456133a89a 100644 --- a/sound/soc/codecs/isabelle.c +++ b/sound/soc/codecs/isabelle.c @@ -1142,7 +1142,7 @@ static struct i2c_driver isabelle_i2c_driver = { .driver = { .name = "isabelle", }, - .probe_new = isabelle_i2c_probe, + .probe = isabelle_i2c_probe, .id_table = isabelle_i2c_id, }; diff --git a/sound/soc/codecs/lm4857.c b/sound/soc/codecs/lm4857.c index dba161305de8..e7542f71323d 100644 --- a/sound/soc/codecs/lm4857.c +++ b/sound/soc/codecs/lm4857.c @@ -137,7 +137,7 @@ static struct i2c_driver lm4857_i2c_driver = { .driver = { .name = "lm4857", }, - .probe_new = lm4857_i2c_probe, + .probe = lm4857_i2c_probe, .id_table = lm4857_i2c_id, }; diff --git a/sound/soc/codecs/lm49453.c b/sound/soc/codecs/lm49453.c index a2e782cc4276..a4094689b3dd 100644 --- a/sound/soc/codecs/lm49453.c +++ b/sound/soc/codecs/lm49453.c @@ -1451,7 +1451,7 @@ static struct i2c_driver lm49453_i2c_driver = { .driver = { .name = "lm49453", }, - .probe_new = lm49453_i2c_probe, + .probe = lm49453_i2c_probe, .id_table = lm49453_i2c_id, }; diff --git a/sound/soc/codecs/max9768.c b/sound/soc/codecs/max9768.c index d711eb1da0a8..d22b4ba51ed8 100644 --- a/sound/soc/codecs/max9768.c +++ b/sound/soc/codecs/max9768.c @@ -214,7 +214,7 @@ static struct i2c_driver max9768_i2c_driver = { .driver = { .name = "max9768", }, - .probe_new = max9768_i2c_probe, + .probe = max9768_i2c_probe, .id_table = max9768_i2c_id, }; module_i2c_driver(max9768_i2c_driver); diff --git a/sound/soc/codecs/max98088.c b/sound/soc/codecs/max98088.c index 405ec16be2b6..fb136e2b849b 100644 --- a/sound/soc/codecs/max98088.c +++ b/sound/soc/codecs/max98088.c @@ -1789,7 +1789,7 @@ static struct i2c_driver max98088_i2c_driver = { .name = "max98088", .of_match_table = of_match_ptr(max98088_of_match), }, - .probe_new = max98088_i2c_probe, + .probe = max98088_i2c_probe, .id_table = max98088_i2c_id, }; diff --git a/sound/soc/codecs/max98090.c b/sound/soc/codecs/max98090.c index b419c49e1e08..ad417d80691f 100644 --- a/sound/soc/codecs/max98090.c +++ b/sound/soc/codecs/max98090.c @@ -2691,7 +2691,7 @@ static struct i2c_driver max98090_i2c_driver = { .of_match_table = of_match_ptr(max98090_of_match), .acpi_match_table = ACPI_PTR(max98090_acpi_match), }, - .probe_new = max98090_i2c_probe, + .probe = max98090_i2c_probe, .shutdown = max98090_i2c_shutdown, .remove = max98090_i2c_remove, .id_table = max98090_i2c_id, diff --git a/sound/soc/codecs/max98095.c b/sound/soc/codecs/max98095.c index 44aa58fcc23f..7e525d49328d 100644 --- a/sound/soc/codecs/max98095.c +++ b/sound/soc/codecs/max98095.c @@ -2155,7 +2155,7 @@ static struct i2c_driver max98095_i2c_driver = { .name = "max98095", .of_match_table = of_match_ptr(max98095_of_match), }, - .probe_new = max98095_i2c_probe, + .probe = max98095_i2c_probe, .id_table = max98095_i2c_id, }; diff --git a/sound/soc/codecs/max98371.c b/sound/soc/codecs/max98371.c index bac9d1bcf60a..f0e49179c38f 100644 --- a/sound/soc/codecs/max98371.c +++ b/sound/soc/codecs/max98371.c @@ -419,7 +419,7 @@ static struct i2c_driver max98371_i2c_driver = { .name = "max98371", .of_match_table = of_match_ptr(max98371_of_match), }, - .probe_new = max98371_i2c_probe, + .probe = max98371_i2c_probe, .id_table = max98371_i2c_id, }; diff --git a/sound/soc/codecs/max98373-i2c.c b/sound/soc/codecs/max98373-i2c.c index ec0905df65d1..3d6da4f133de 100644 --- a/sound/soc/codecs/max98373-i2c.c +++ b/sound/soc/codecs/max98373-i2c.c @@ -624,7 +624,7 @@ static struct i2c_driver max98373_i2c_driver = { .acpi_match_table = ACPI_PTR(max98373_acpi_match), .pm = &max98373_pm, }, - .probe_new = max98373_i2c_probe, + .probe = max98373_i2c_probe, .id_table = max98373_i2c_id, }; diff --git a/sound/soc/codecs/max98390.c b/sound/soc/codecs/max98390.c index 7a5260ff8d6b..5b8e78e51630 100644 --- a/sound/soc/codecs/max98390.c +++ b/sound/soc/codecs/max98390.c @@ -1133,7 +1133,7 @@ static struct i2c_driver max98390_i2c_driver = { .acpi_match_table = ACPI_PTR(max98390_acpi_match), .pm = &max98390_pm, }, - .probe_new = max98390_i2c_probe, + .probe = max98390_i2c_probe, .id_table = max98390_i2c_id, }; diff --git a/sound/soc/codecs/max98396.c b/sound/soc/codecs/max98396.c index db3de41f10e0..3a1d8c211f3c 100644 --- a/sound/soc/codecs/max98396.c +++ b/sound/soc/codecs/max98396.c @@ -1907,7 +1907,7 @@ static struct i2c_driver max98396_i2c_driver = { .acpi_match_table = ACPI_PTR(max98396_acpi_match), .pm = &max98396_pm, }, - .probe_new = max98396_i2c_probe, + .probe = max98396_i2c_probe, .id_table = max98396_i2c_id, }; diff --git a/sound/soc/codecs/max9850.c b/sound/soc/codecs/max9850.c index a6733396b0ca..8b012a85360a 100644 --- a/sound/soc/codecs/max9850.c +++ b/sound/soc/codecs/max9850.c @@ -329,7 +329,7 @@ static struct i2c_driver max9850_i2c_driver = { .driver = { .name = "max9850", }, - .probe_new = max9850_i2c_probe, + .probe = max9850_i2c_probe, .id_table = max9850_i2c_id, }; diff --git a/sound/soc/codecs/max98504.c b/sound/soc/codecs/max98504.c index 0daa2a3dd621..93412b966b33 100644 --- a/sound/soc/codecs/max98504.c +++ b/sound/soc/codecs/max98504.c @@ -371,7 +371,7 @@ static struct i2c_driver max98504_i2c_driver = { .name = "max98504", .of_match_table = of_match_ptr(max98504_of_match), }, - .probe_new = max98504_i2c_probe, + .probe = max98504_i2c_probe, .id_table = max98504_i2c_id, }; module_i2c_driver(max98504_i2c_driver); diff --git a/sound/soc/codecs/max98520.c b/sound/soc/codecs/max98520.c index 5edd6f90f8a7..8637fff307ad 100644 --- a/sound/soc/codecs/max98520.c +++ b/sound/soc/codecs/max98520.c @@ -756,7 +756,7 @@ static struct i2c_driver max98520_i2c_driver = { .of_match_table = of_match_ptr(max98520_of_match), .pm = &max98520_pm, }, - .probe_new = max98520_i2c_probe, + .probe = max98520_i2c_probe, .id_table = max98520_i2c_id, }; diff --git a/sound/soc/codecs/max9860.c b/sound/soc/codecs/max9860.c index 9611ab1e79e5..4015ed2c47ec 100644 --- a/sound/soc/codecs/max9860.c +++ b/sound/soc/codecs/max9860.c @@ -723,7 +723,7 @@ static const struct of_device_id max9860_of_match[] = { MODULE_DEVICE_TABLE(of, max9860_of_match); static struct i2c_driver max9860_i2c_driver = { - .probe_new = max9860_probe, + .probe = max9860_probe, .remove = max9860_remove, .id_table = max9860_i2c_id, .driver = { diff --git a/sound/soc/codecs/max9867.c b/sound/soc/codecs/max9867.c index e161ab037bf7..a95923767ac6 100644 --- a/sound/soc/codecs/max9867.c +++ b/sound/soc/codecs/max9867.c @@ -687,7 +687,7 @@ static struct i2c_driver max9867_i2c_driver = { .name = "max9867", .of_match_table = of_match_ptr(max9867_of_match), }, - .probe_new = max9867_i2c_probe, + .probe = max9867_i2c_probe, .id_table = max9867_i2c_id, }; diff --git a/sound/soc/codecs/max9877.c b/sound/soc/codecs/max9877.c index 3bf86328d5cd..2ae64fcf29c7 100644 --- a/sound/soc/codecs/max9877.c +++ b/sound/soc/codecs/max9877.c @@ -160,7 +160,7 @@ static struct i2c_driver max9877_i2c_driver = { .driver = { .name = "max9877", }, - .probe_new = max9877_i2c_probe, + .probe = max9877_i2c_probe, .id_table = max9877_i2c_id, }; diff --git a/sound/soc/codecs/max98925.c b/sound/soc/codecs/max98925.c index c24d9f2c8874..a9c1d85cd0d5 100644 --- a/sound/soc/codecs/max98925.c +++ b/sound/soc/codecs/max98925.c @@ -635,7 +635,7 @@ static struct i2c_driver max98925_i2c_driver = { .name = "max98925", .of_match_table = of_match_ptr(max98925_of_match), }, - .probe_new = max98925_i2c_probe, + .probe = max98925_i2c_probe, .id_table = max98925_i2c_id, }; diff --git a/sound/soc/codecs/max98926.c b/sound/soc/codecs/max98926.c index bffd56e240e9..bdc508e23e59 100644 --- a/sound/soc/codecs/max98926.c +++ b/sound/soc/codecs/max98926.c @@ -582,7 +582,7 @@ static struct i2c_driver max98926_i2c_driver = { .name = "max98926", .of_match_table = of_match_ptr(max98926_of_match), }, - .probe_new = max98926_i2c_probe, + .probe = max98926_i2c_probe, .id_table = max98926_i2c_id, }; diff --git a/sound/soc/codecs/max98927.c b/sound/soc/codecs/max98927.c index 331d3e1d735c..0aaf2e6ae78d 100644 --- a/sound/soc/codecs/max98927.c +++ b/sound/soc/codecs/max98927.c @@ -973,7 +973,7 @@ static struct i2c_driver max98927_i2c_driver = { .acpi_match_table = ACPI_PTR(max98927_acpi_match), .pm = &max98927_pm, }, - .probe_new = max98927_i2c_probe, + .probe = max98927_i2c_probe, .remove = max98927_i2c_remove, .id_table = max98927_i2c_id, }; diff --git a/sound/soc/codecs/ml26124.c b/sound/soc/codecs/ml26124.c index 3c6ac77379cb..a45ef9d65703 100644 --- a/sound/soc/codecs/ml26124.c +++ b/sound/soc/codecs/ml26124.c @@ -581,7 +581,7 @@ static struct i2c_driver ml26124_i2c_driver = { .driver = { .name = "ml26124", }, - .probe_new = ml26124_i2c_probe, + .probe = ml26124_i2c_probe, .id_table = ml26124_i2c_id, }; diff --git a/sound/soc/codecs/mt6660.c b/sound/soc/codecs/mt6660.c index cc2df5f7ea19..5c50c7de26cd 100644 --- a/sound/soc/codecs/mt6660.c +++ b/sound/soc/codecs/mt6660.c @@ -570,7 +570,7 @@ static struct i2c_driver mt6660_i2c_driver = { .of_match_table = of_match_ptr(mt6660_of_id), .pm = &mt6660_dev_pm_ops, }, - .probe_new = mt6660_i2c_probe, + .probe = mt6660_i2c_probe, .remove = mt6660_i2c_remove, .id_table = mt6660_i2c_id, }; diff --git a/sound/soc/codecs/nau8540.c b/sound/soc/codecs/nau8540.c index 0626d5694c22..2174a89772fc 100644 --- a/sound/soc/codecs/nau8540.c +++ b/sound/soc/codecs/nau8540.c @@ -890,7 +890,7 @@ static struct i2c_driver nau8540_i2c_driver = { .name = "nau8540", .of_match_table = of_match_ptr(nau8540_of_ids), }, - .probe_new = nau8540_i2c_probe, + .probe = nau8540_i2c_probe, .id_table = nau8540_i2c_ids, }; module_i2c_driver(nau8540_i2c_driver); diff --git a/sound/soc/codecs/nau8810.c b/sound/soc/codecs/nau8810.c index ccb512c21d74..47f000cd4d99 100644 --- a/sound/soc/codecs/nau8810.c +++ b/sound/soc/codecs/nau8810.c @@ -914,7 +914,7 @@ static struct i2c_driver nau8810_i2c_driver = { .name = "nau8810", .of_match_table = of_match_ptr(nau8810_of_match), }, - .probe_new = nau8810_i2c_probe, + .probe = nau8810_i2c_probe, .id_table = nau8810_i2c_id, }; diff --git a/sound/soc/codecs/nau8821.c b/sound/soc/codecs/nau8821.c index 4a72b94e8410..47f170f8793a 100644 --- a/sound/soc/codecs/nau8821.c +++ b/sound/soc/codecs/nau8821.c @@ -1763,7 +1763,7 @@ static struct i2c_driver nau8821_driver = { .of_match_table = of_match_ptr(nau8821_of_ids), .acpi_match_table = ACPI_PTR(nau8821_acpi_match), }, - .probe_new = nau8821_i2c_probe, + .probe = nau8821_i2c_probe, .id_table = nau8821_i2c_ids, }; module_i2c_driver(nau8821_driver); diff --git a/sound/soc/codecs/nau8822.c b/sound/soc/codecs/nau8822.c index d5006d8de639..ff3024899f45 100644 --- a/sound/soc/codecs/nau8822.c +++ b/sound/soc/codecs/nau8822.c @@ -1166,7 +1166,7 @@ static struct i2c_driver nau8822_i2c_driver = { .name = "nau8822", .of_match_table = of_match_ptr(nau8822_of_match), }, - .probe_new = nau8822_i2c_probe, + .probe = nau8822_i2c_probe, .id_table = nau8822_i2c_id, }; module_i2c_driver(nau8822_i2c_driver); diff --git a/sound/soc/codecs/nau8824.c b/sound/soc/codecs/nau8824.c index 4f19fd9b65d1..8ee47d4d750a 100644 --- a/sound/soc/codecs/nau8824.c +++ b/sound/soc/codecs/nau8824.c @@ -2006,7 +2006,7 @@ static struct i2c_driver nau8824_i2c_driver = { .of_match_table = of_match_ptr(nau8824_of_ids), .acpi_match_table = ACPI_PTR(nau8824_acpi_match), }, - .probe_new = nau8824_i2c_probe, + .probe = nau8824_i2c_probe, .id_table = nau8824_i2c_ids, }; module_i2c_driver(nau8824_i2c_driver); diff --git a/sound/soc/codecs/nau8825.c b/sound/soc/codecs/nau8825.c index 4bffa9c20f2b..3f897a9596cc 100644 --- a/sound/soc/codecs/nau8825.c +++ b/sound/soc/codecs/nau8825.c @@ -2938,7 +2938,7 @@ static struct i2c_driver nau8825_driver = { .of_match_table = of_match_ptr(nau8825_of_ids), .acpi_match_table = ACPI_PTR(nau8825_acpi_match), }, - .probe_new = nau8825_i2c_probe, + .probe = nau8825_i2c_probe, .remove = nau8825_i2c_remove, .id_table = nau8825_i2c_ids, }; diff --git a/sound/soc/codecs/pcm1681.c b/sound/soc/codecs/pcm1681.c index 3591f6f53901..735e1942b530 100644 --- a/sound/soc/codecs/pcm1681.c +++ b/sound/soc/codecs/pcm1681.c @@ -327,7 +327,7 @@ static struct i2c_driver pcm1681_i2c_driver = { .of_match_table = of_match_ptr(pcm1681_dt_ids), }, .id_table = pcm1681_i2c_id, - .probe_new = pcm1681_i2c_probe, + .probe = pcm1681_i2c_probe, }; module_i2c_driver(pcm1681_i2c_driver); diff --git a/sound/soc/codecs/pcm1789-i2c.c b/sound/soc/codecs/pcm1789-i2c.c index fafe0dcbe4ea..f2d0b4d21e41 100644 --- a/sound/soc/codecs/pcm1789-i2c.c +++ b/sound/soc/codecs/pcm1789-i2c.c @@ -52,7 +52,7 @@ static struct i2c_driver pcm1789_i2c_driver = { .of_match_table = of_match_ptr(pcm1789_of_match), }, .id_table = pcm1789_i2c_ids, - .probe_new = pcm1789_i2c_probe, + .probe = pcm1789_i2c_probe, .remove = pcm1789_i2c_remove, }; diff --git a/sound/soc/codecs/pcm179x-i2c.c b/sound/soc/codecs/pcm179x-i2c.c index e20fe3a85af8..10579681f44b 100644 --- a/sound/soc/codecs/pcm179x-i2c.c +++ b/sound/soc/codecs/pcm179x-i2c.c @@ -49,7 +49,7 @@ static struct i2c_driver pcm179x_i2c_driver = { .of_match_table = of_match_ptr(pcm179x_of_match), }, .id_table = pcm179x_i2c_ids, - .probe_new = pcm179x_i2c_probe, + .probe = pcm179x_i2c_probe, }; module_i2c_driver(pcm179x_i2c_driver); diff --git a/sound/soc/codecs/pcm186x-i2c.c b/sound/soc/codecs/pcm186x-i2c.c index 932c8d41c3ea..a514ebd1b68a 100644 --- a/sound/soc/codecs/pcm186x-i2c.c +++ b/sound/soc/codecs/pcm186x-i2c.c @@ -46,7 +46,7 @@ static int pcm186x_i2c_probe(struct i2c_client *i2c) } static struct i2c_driver pcm186x_i2c_driver = { - .probe_new = pcm186x_i2c_probe, + .probe = pcm186x_i2c_probe, .id_table = pcm186x_i2c_id, .driver = { .name = "pcm186x", diff --git a/sound/soc/codecs/pcm3060-i2c.c b/sound/soc/codecs/pcm3060-i2c.c index 2388098eeca3..5330cf46b127 100644 --- a/sound/soc/codecs/pcm3060-i2c.c +++ b/sound/soc/codecs/pcm3060-i2c.c @@ -49,7 +49,7 @@ static struct i2c_driver pcm3060_i2c_driver = { #endif /* CONFIG_OF */ }, .id_table = pcm3060_i2c_id, - .probe_new = pcm3060_i2c_probe, + .probe = pcm3060_i2c_probe, }; module_i2c_driver(pcm3060_i2c_driver); diff --git a/sound/soc/codecs/pcm3168a-i2c.c b/sound/soc/codecs/pcm3168a-i2c.c index a0eec82e9872..7052cc0c97d1 100644 --- a/sound/soc/codecs/pcm3168a-i2c.c +++ b/sound/soc/codecs/pcm3168a-i2c.c @@ -44,7 +44,7 @@ static const struct of_device_id pcm3168a_of_match[] = { MODULE_DEVICE_TABLE(of, pcm3168a_of_match); static struct i2c_driver pcm3168a_i2c_driver = { - .probe_new = pcm3168a_i2c_probe, + .probe = pcm3168a_i2c_probe, .remove = pcm3168a_i2c_remove, .id_table = pcm3168a_i2c_id, .driver = { diff --git a/sound/soc/codecs/pcm512x-i2c.c b/sound/soc/codecs/pcm512x-i2c.c index 9dfbbe8f4a0b..5cd2b64b9337 100644 --- a/sound/soc/codecs/pcm512x-i2c.c +++ b/sound/soc/codecs/pcm512x-i2c.c @@ -66,7 +66,7 @@ MODULE_DEVICE_TABLE(acpi, pcm512x_acpi_match); #endif static struct i2c_driver pcm512x_i2c_driver = { - .probe_new = pcm512x_i2c_probe, + .probe = pcm512x_i2c_probe, .remove = pcm512x_i2c_remove, .id_table = pcm512x_i2c_id, .driver = { diff --git a/sound/soc/codecs/rt1011.c b/sound/soc/codecs/rt1011.c index c1568216126e..4ceb410c5024 100644 --- a/sound/soc/codecs/rt1011.c +++ b/sound/soc/codecs/rt1011.c @@ -2483,7 +2483,7 @@ static struct i2c_driver rt1011_i2c_driver = { .of_match_table = of_match_ptr(rt1011_of_match), .acpi_match_table = ACPI_PTR(rt1011_acpi_match) }, - .probe_new = rt1011_i2c_probe, + .probe = rt1011_i2c_probe, .shutdown = rt1011_i2c_shutdown, .id_table = rt1011_i2c_id, }; diff --git a/sound/soc/codecs/rt1015.c b/sound/soc/codecs/rt1015.c index 57d0f1c69e46..38d9f69b08d6 100644 --- a/sound/soc/codecs/rt1015.c +++ b/sound/soc/codecs/rt1015.c @@ -1170,7 +1170,7 @@ static struct i2c_driver rt1015_i2c_driver = { .of_match_table = of_match_ptr(rt1015_of_match), .acpi_match_table = ACPI_PTR(rt1015_acpi_match), }, - .probe_new = rt1015_i2c_probe, + .probe = rt1015_i2c_probe, .shutdown = rt1015_i2c_shutdown, .id_table = rt1015_i2c_id, }; diff --git a/sound/soc/codecs/rt1016.c b/sound/soc/codecs/rt1016.c index 37eeec650f03..b1e69fa290b2 100644 --- a/sound/soc/codecs/rt1016.c +++ b/sound/soc/codecs/rt1016.c @@ -683,7 +683,7 @@ static struct i2c_driver rt1016_i2c_driver = { .of_match_table = of_match_ptr(rt1016_of_match), .acpi_match_table = ACPI_PTR(rt1016_acpi_match), }, - .probe_new = rt1016_i2c_probe, + .probe = rt1016_i2c_probe, .shutdown = rt1016_i2c_shutdown, .id_table = rt1016_i2c_id, }; diff --git a/sound/soc/codecs/rt1019.c b/sound/soc/codecs/rt1019.c index 49f527c61a7a..db7da62348f9 100644 --- a/sound/soc/codecs/rt1019.c +++ b/sound/soc/codecs/rt1019.c @@ -600,7 +600,7 @@ static struct i2c_driver rt1019_i2c_driver = { .of_match_table = of_match_ptr(rt1019_of_match), .acpi_match_table = ACPI_PTR(rt1019_acpi_match), }, - .probe_new = rt1019_i2c_probe, + .probe = rt1019_i2c_probe, .id_table = rt1019_i2c_id, }; module_i2c_driver(rt1019_i2c_driver); diff --git a/sound/soc/codecs/rt1305.c b/sound/soc/codecs/rt1305.c index 5b39a440b6dc..28a4a70c3307 100644 --- a/sound/soc/codecs/rt1305.c +++ b/sound/soc/codecs/rt1305.c @@ -1170,7 +1170,7 @@ static struct i2c_driver rt1305_i2c_driver = { .acpi_match_table = ACPI_PTR(rt1305_acpi_match) #endif }, - .probe_new = rt1305_i2c_probe, + .probe = rt1305_i2c_probe, .shutdown = rt1305_i2c_shutdown, .id_table = rt1305_i2c_id, }; diff --git a/sound/soc/codecs/rt1308.c b/sound/soc/codecs/rt1308.c index d2a8e9fe3e23..04c5d5de71ff 100644 --- a/sound/soc/codecs/rt1308.c +++ b/sound/soc/codecs/rt1308.c @@ -862,7 +862,7 @@ static struct i2c_driver rt1308_i2c_driver = { .of_match_table = of_match_ptr(rt1308_of_match), .acpi_match_table = ACPI_PTR(rt1308_acpi_match), }, - .probe_new = rt1308_i2c_probe, + .probe = rt1308_i2c_probe, .shutdown = rt1308_i2c_shutdown, .id_table = rt1308_i2c_id, }; diff --git a/sound/soc/codecs/rt274.c b/sound/soc/codecs/rt274.c index 4667bf7561b1..9a33e3776b55 100644 --- a/sound/soc/codecs/rt274.c +++ b/sound/soc/codecs/rt274.c @@ -1221,7 +1221,7 @@ static struct i2c_driver rt274_i2c_driver = { .of_match_table = of_match_ptr(rt274_of_match), #endif }, - .probe_new = rt274_i2c_probe, + .probe = rt274_i2c_probe, .remove = rt274_i2c_remove, .id_table = rt274_i2c_id, }; diff --git a/sound/soc/codecs/rt286.c b/sound/soc/codecs/rt286.c index ceb56647e369..981155b046fd 100644 --- a/sound/soc/codecs/rt286.c +++ b/sound/soc/codecs/rt286.c @@ -1263,7 +1263,7 @@ static struct i2c_driver rt286_i2c_driver = { .name = "rt286", .acpi_match_table = ACPI_PTR(rt286_acpi_match), }, - .probe_new = rt286_i2c_probe, + .probe = rt286_i2c_probe, .remove = rt286_i2c_remove, .id_table = rt286_i2c_id, }; diff --git a/sound/soc/codecs/rt298.c b/sound/soc/codecs/rt298.c index cea26f3a02b6..8fbd25ad9b47 100644 --- a/sound/soc/codecs/rt298.c +++ b/sound/soc/codecs/rt298.c @@ -1311,7 +1311,7 @@ static struct i2c_driver rt298_i2c_driver = { .name = "rt298", .acpi_match_table = ACPI_PTR(rt298_acpi_match), }, - .probe_new = rt298_i2c_probe, + .probe = rt298_i2c_probe, .remove = rt298_i2c_remove, .id_table = rt298_i2c_id, }; diff --git a/sound/soc/codecs/rt5514.c b/sound/soc/codecs/rt5514.c index b9bcf04d4dc9..0f9f52b93e36 100644 --- a/sound/soc/codecs/rt5514.c +++ b/sound/soc/codecs/rt5514.c @@ -1328,7 +1328,7 @@ static struct i2c_driver rt5514_i2c_driver = { .of_match_table = of_match_ptr(rt5514_of_match), .pm = &rt5514_i2_pm_ops, }, - .probe_new = rt5514_i2c_probe, + .probe = rt5514_i2c_probe, .id_table = rt5514_i2c_id, }; module_i2c_driver(rt5514_i2c_driver); diff --git a/sound/soc/codecs/rt5616.c b/sound/soc/codecs/rt5616.c index 948abde10463..91c967391de9 100644 --- a/sound/soc/codecs/rt5616.c +++ b/sound/soc/codecs/rt5616.c @@ -1404,7 +1404,7 @@ static struct i2c_driver rt5616_i2c_driver = { .name = "rt5616", .of_match_table = of_match_ptr(rt5616_of_match), }, - .probe_new = rt5616_i2c_probe, + .probe = rt5616_i2c_probe, .remove = rt5616_i2c_remove, .shutdown = rt5616_i2c_shutdown, .id_table = rt5616_i2c_id, diff --git a/sound/soc/codecs/rt5631.c b/sound/soc/codecs/rt5631.c index 55c232413e2b..9a4cb45e37d4 100644 --- a/sound/soc/codecs/rt5631.c +++ b/sound/soc/codecs/rt5631.c @@ -1728,7 +1728,7 @@ static struct i2c_driver rt5631_i2c_driver = { .name = "rt5631", .of_match_table = of_match_ptr(rt5631_i2c_dt_ids), }, - .probe_new = rt5631_i2c_probe, + .probe = rt5631_i2c_probe, .remove = rt5631_i2c_remove, .id_table = rt5631_i2c_id, }; diff --git a/sound/soc/codecs/rt5640.c b/sound/soc/codecs/rt5640.c index 139257055507..c7d2f315273e 100644 --- a/sound/soc/codecs/rt5640.c +++ b/sound/soc/codecs/rt5640.c @@ -3079,7 +3079,7 @@ static struct i2c_driver rt5640_i2c_driver = { .acpi_match_table = ACPI_PTR(rt5640_acpi_match), .of_match_table = of_match_ptr(rt5640_of_match), }, - .probe_new = rt5640_i2c_probe, + .probe = rt5640_i2c_probe, .id_table = rt5640_i2c_id, }; module_i2c_driver(rt5640_i2c_driver); diff --git a/sound/soc/codecs/rt5645.c b/sound/soc/codecs/rt5645.c index 7c7cbb6362ea..01aa999fc6db 100644 --- a/sound/soc/codecs/rt5645.c +++ b/sound/soc/codecs/rt5645.c @@ -4184,7 +4184,7 @@ static struct i2c_driver rt5645_i2c_driver = { .of_match_table = of_match_ptr(rt5645_of_match), .acpi_match_table = ACPI_PTR(rt5645_acpi_match), }, - .probe_new = rt5645_i2c_probe, + .probe = rt5645_i2c_probe, .remove = rt5645_i2c_remove, .shutdown = rt5645_i2c_shutdown, .id_table = rt5645_i2c_id, diff --git a/sound/soc/codecs/rt5651.c b/sound/soc/codecs/rt5651.c index df90af906563..b2ec44fa478b 100644 --- a/sound/soc/codecs/rt5651.c +++ b/sound/soc/codecs/rt5651.c @@ -2279,7 +2279,7 @@ static struct i2c_driver rt5651_i2c_driver = { .acpi_match_table = ACPI_PTR(rt5651_acpi_match), .of_match_table = of_match_ptr(rt5651_of_match), }, - .probe_new = rt5651_i2c_probe, + .probe = rt5651_i2c_probe, .id_table = rt5651_i2c_id, }; module_i2c_driver(rt5651_i2c_driver); diff --git a/sound/soc/codecs/rt5659.c b/sound/soc/codecs/rt5659.c index 5e21e3c37ab5..22bb57029bc0 100644 --- a/sound/soc/codecs/rt5659.c +++ b/sound/soc/codecs/rt5659.c @@ -4340,7 +4340,7 @@ static struct i2c_driver rt5659_i2c_driver = { .of_match_table = of_match_ptr(rt5659_of_match), .acpi_match_table = ACPI_PTR(rt5659_acpi_match), }, - .probe_new = rt5659_i2c_probe, + .probe = rt5659_i2c_probe, .shutdown = rt5659_i2c_shutdown, .id_table = rt5659_i2c_id, }; diff --git a/sound/soc/codecs/rt5660.c b/sound/soc/codecs/rt5660.c index 341baa29fdb1..fd453f47455b 100644 --- a/sound/soc/codecs/rt5660.c +++ b/sound/soc/codecs/rt5660.c @@ -1341,7 +1341,7 @@ static struct i2c_driver rt5660_i2c_driver = { .acpi_match_table = ACPI_PTR(rt5660_acpi_match), .of_match_table = of_match_ptr(rt5660_of_match), }, - .probe_new = rt5660_i2c_probe, + .probe = rt5660_i2c_probe, .id_table = rt5660_i2c_id, }; module_i2c_driver(rt5660_i2c_driver); diff --git a/sound/soc/codecs/rt5663.c b/sound/soc/codecs/rt5663.c index f73751dbde30..ceeadbb4f62d 100644 --- a/sound/soc/codecs/rt5663.c +++ b/sound/soc/codecs/rt5663.c @@ -3733,7 +3733,7 @@ static struct i2c_driver rt5663_i2c_driver = { .acpi_match_table = ACPI_PTR(rt5663_acpi_match), .of_match_table = of_match_ptr(rt5663_of_match), }, - .probe_new = rt5663_i2c_probe, + .probe = rt5663_i2c_probe, .remove = rt5663_i2c_remove, .shutdown = rt5663_i2c_shutdown, .id_table = rt5663_i2c_id, diff --git a/sound/soc/codecs/rt5665.c b/sound/soc/codecs/rt5665.c index 17afaef85c77..732e15e3a497 100644 --- a/sound/soc/codecs/rt5665.c +++ b/sound/soc/codecs/rt5665.c @@ -4968,7 +4968,7 @@ static struct i2c_driver rt5665_i2c_driver = { .of_match_table = of_match_ptr(rt5665_of_match), .acpi_match_table = ACPI_PTR(rt5665_acpi_match), }, - .probe_new = rt5665_i2c_probe, + .probe = rt5665_i2c_probe, .shutdown = rt5665_i2c_shutdown, .id_table = rt5665_i2c_id, }; diff --git a/sound/soc/codecs/rt5668.c b/sound/soc/codecs/rt5668.c index ecf3b0527dbe..13fec49d4824 100644 --- a/sound/soc/codecs/rt5668.c +++ b/sound/soc/codecs/rt5668.c @@ -2618,7 +2618,7 @@ static struct i2c_driver rt5668_i2c_driver = { .of_match_table = of_match_ptr(rt5668_of_match), .acpi_match_table = ACPI_PTR(rt5668_acpi_match), }, - .probe_new = rt5668_i2c_probe, + .probe = rt5668_i2c_probe, .shutdown = rt5668_i2c_shutdown, .id_table = rt5668_i2c_id, }; diff --git a/sound/soc/codecs/rt5670.c b/sound/soc/codecs/rt5670.c index a230f441559a..e8ce3e7c8e3f 100644 --- a/sound/soc/codecs/rt5670.c +++ b/sound/soc/codecs/rt5670.c @@ -3328,7 +3328,7 @@ static struct i2c_driver rt5670_i2c_driver = { .name = "rt5670", .acpi_match_table = ACPI_PTR(rt5670_acpi_match), }, - .probe_new = rt5670_i2c_probe, + .probe = rt5670_i2c_probe, .remove = rt5670_i2c_remove, .id_table = rt5670_i2c_id, }; diff --git a/sound/soc/codecs/rt5677.c b/sound/soc/codecs/rt5677.c index c26395f42d8e..0711f7dae6c6 100644 --- a/sound/soc/codecs/rt5677.c +++ b/sound/soc/codecs/rt5677.c @@ -5704,7 +5704,7 @@ static struct i2c_driver rt5677_i2c_driver = { .of_match_table = rt5677_of_match, .acpi_match_table = ACPI_PTR(rt5677_acpi_match), }, - .probe_new = rt5677_i2c_probe, + .probe = rt5677_i2c_probe, .remove = rt5677_i2c_remove, }; module_i2c_driver(rt5677_i2c_driver); diff --git a/sound/soc/codecs/rt5682-i2c.c b/sound/soc/codecs/rt5682-i2c.c index 2935c1bb81f3..d0041ba1e627 100644 --- a/sound/soc/codecs/rt5682-i2c.c +++ b/sound/soc/codecs/rt5682-i2c.c @@ -332,7 +332,7 @@ static struct i2c_driver rt5682_i2c_driver = { .acpi_match_table = rt5682_acpi_match, .probe_type = PROBE_PREFER_ASYNCHRONOUS, }, - .probe_new = rt5682_i2c_probe, + .probe = rt5682_i2c_probe, .remove = rt5682_i2c_remove, .shutdown = rt5682_i2c_shutdown, .id_table = rt5682_i2c_id, diff --git a/sound/soc/codecs/rt5682s.c b/sound/soc/codecs/rt5682s.c index 9c34dca58f54..6ac0c14de85c 100644 --- a/sound/soc/codecs/rt5682s.c +++ b/sound/soc/codecs/rt5682s.c @@ -3316,7 +3316,7 @@ static struct i2c_driver rt5682s_i2c_driver = { .acpi_match_table = rt5682s_acpi_match, .probe_type = PROBE_PREFER_ASYNCHRONOUS, }, - .probe_new = rt5682s_i2c_probe, + .probe = rt5682s_i2c_probe, .remove = rt5682s_i2c_remove, .shutdown = rt5682s_i2c_shutdown, .id_table = rt5682s_i2c_id, diff --git a/sound/soc/codecs/rt9120.c b/sound/soc/codecs/rt9120.c index fcf4fbaed3c7..733a7d130a95 100644 --- a/sound/soc/codecs/rt9120.c +++ b/sound/soc/codecs/rt9120.c @@ -633,7 +633,7 @@ static struct i2c_driver rt9120_driver = { .of_match_table = rt9120_device_table, .pm = &rt9120_pm_ops, }, - .probe_new = rt9120_probe, + .probe = rt9120_probe, .remove = rt9120_remove, }; module_i2c_driver(rt9120_driver); diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c index a916f4619ea3..b22ba95bd0c0 100644 --- a/sound/soc/codecs/sgtl5000.c +++ b/sound/soc/codecs/sgtl5000.c @@ -1826,7 +1826,7 @@ static struct i2c_driver sgtl5000_i2c_driver = { .name = "sgtl5000", .of_match_table = sgtl5000_dt_ids, }, - .probe_new = sgtl5000_i2c_probe, + .probe = sgtl5000_i2c_probe, .remove = sgtl5000_i2c_remove, .shutdown = sgtl5000_i2c_shutdown, .id_table = sgtl5000_id, diff --git a/sound/soc/codecs/sma1303.c b/sound/soc/codecs/sma1303.c index fa4b0a60f8a9..85132df505e9 100644 --- a/sound/soc/codecs/sma1303.c +++ b/sound/soc/codecs/sma1303.c @@ -1807,7 +1807,7 @@ static struct i2c_driver sma1303_i2c_driver = { .name = "sma1303", .of_match_table = sma1303_of_match, }, - .probe_new = sma1303_i2c_probe, + .probe = sma1303_i2c_probe, .remove = sma1303_i2c_remove, .id_table = sma1303_i2c_id, }; diff --git a/sound/soc/codecs/src4xxx-i2c.c b/sound/soc/codecs/src4xxx-i2c.c index 27026030704a..301d5e73de26 100644 --- a/sound/soc/codecs/src4xxx-i2c.c +++ b/sound/soc/codecs/src4xxx-i2c.c @@ -36,7 +36,7 @@ static struct i2c_driver src4xxx_i2c_driver = { .name = "src4xxx", .of_match_table = of_match_ptr(src4xxx_of_match), }, - .probe_new = src4xxx_i2c_probe, + .probe = src4xxx_i2c_probe, .id_table = src4xxx_i2c_ids, }; module_i2c_driver(src4xxx_i2c_driver); diff --git a/sound/soc/codecs/ssm2518.c b/sound/soc/codecs/ssm2518.c index 22cb3b7c8283..d20d897407eb 100644 --- a/sound/soc/codecs/ssm2518.c +++ b/sound/soc/codecs/ssm2518.c @@ -803,7 +803,7 @@ static struct i2c_driver ssm2518_driver = { .name = "ssm2518", .of_match_table = of_match_ptr(ssm2518_dt_ids), }, - .probe_new = ssm2518_i2c_probe, + .probe = ssm2518_i2c_probe, .id_table = ssm2518_i2c_ids, }; module_i2c_driver(ssm2518_driver); diff --git a/sound/soc/codecs/ssm2602-i2c.c b/sound/soc/codecs/ssm2602-i2c.c index 3c85772901f5..596096466cd4 100644 --- a/sound/soc/codecs/ssm2602-i2c.c +++ b/sound/soc/codecs/ssm2602-i2c.c @@ -49,7 +49,7 @@ static struct i2c_driver ssm2602_i2c_driver = { .name = "ssm2602", .of_match_table = ssm2602_of_match, }, - .probe_new = ssm2602_i2c_probe, + .probe = ssm2602_i2c_probe, .id_table = ssm2602_i2c_id, }; module_i2c_driver(ssm2602_i2c_driver); diff --git a/sound/soc/codecs/ssm4567.c b/sound/soc/codecs/ssm4567.c index 4b0265617c7b..0a6f04d8f636 100644 --- a/sound/soc/codecs/ssm4567.c +++ b/sound/soc/codecs/ssm4567.c @@ -500,7 +500,7 @@ static struct i2c_driver ssm4567_driver = { .of_match_table = of_match_ptr(ssm4567_of_match), .acpi_match_table = ACPI_PTR(ssm4567_acpi_match), }, - .probe_new = ssm4567_i2c_probe, + .probe = ssm4567_i2c_probe, .id_table = ssm4567_i2c_ids, }; module_i2c_driver(ssm4567_driver); diff --git a/sound/soc/codecs/sta32x.c b/sound/soc/codecs/sta32x.c index 8c86b578eba8..b47334e52ef8 100644 --- a/sound/soc/codecs/sta32x.c +++ b/sound/soc/codecs/sta32x.c @@ -1170,7 +1170,7 @@ static struct i2c_driver sta32x_i2c_driver = { .name = "sta32x", .of_match_table = of_match_ptr(st32x_dt_ids), }, - .probe_new = sta32x_i2c_probe, + .probe = sta32x_i2c_probe, .id_table = sta32x_i2c_id, }; diff --git a/sound/soc/codecs/sta350.c b/sound/soc/codecs/sta350.c index 9ed13aeb3cbd..af13ed7b38d7 100644 --- a/sound/soc/codecs/sta350.c +++ b/sound/soc/codecs/sta350.c @@ -1256,7 +1256,7 @@ static struct i2c_driver sta350_i2c_driver = { .name = "sta350", .of_match_table = of_match_ptr(st350_dt_ids), }, - .probe_new = sta350_i2c_probe, + .probe = sta350_i2c_probe, .remove = sta350_i2c_remove, .id_table = sta350_i2c_id, }; diff --git a/sound/soc/codecs/sta529.c b/sound/soc/codecs/sta529.c index 313957099145..0ac08478ddac 100644 --- a/sound/soc/codecs/sta529.c +++ b/sound/soc/codecs/sta529.c @@ -379,7 +379,7 @@ static struct i2c_driver sta529_i2c_driver = { .name = "sta529", .of_match_table = sta529_of_match, }, - .probe_new = sta529_i2c_probe, + .probe = sta529_i2c_probe, .id_table = sta529_i2c_id, }; diff --git a/sound/soc/codecs/tas2552.c b/sound/soc/codecs/tas2552.c index 59a4ea5f6e30..8c9dc318b0e8 100644 --- a/sound/soc/codecs/tas2552.c +++ b/sound/soc/codecs/tas2552.c @@ -761,7 +761,7 @@ static struct i2c_driver tas2552_i2c_driver = { .of_match_table = of_match_ptr(tas2552_of_match), .pm = &tas2552_pm, }, - .probe_new = tas2552_probe, + .probe = tas2552_probe, .remove = tas2552_i2c_remove, .id_table = tas2552_id, }; diff --git a/sound/soc/codecs/tas2562.c b/sound/soc/codecs/tas2562.c index b486d0bd86c9..2012d6f0071d 100644 --- a/sound/soc/codecs/tas2562.c +++ b/sound/soc/codecs/tas2562.c @@ -784,7 +784,7 @@ static struct i2c_driver tas2562_i2c_driver = { .name = "tas2562", .of_match_table = of_match_ptr(tas2562_of_match), }, - .probe_new = tas2562_probe, + .probe = tas2562_probe, .id_table = tas2562_id, }; diff --git a/sound/soc/codecs/tas2764.c b/sound/soc/codecs/tas2764.c index 2e0ed3e68fa5..a9838e0738cc 100644 --- a/sound/soc/codecs/tas2764.c +++ b/sound/soc/codecs/tas2764.c @@ -756,7 +756,7 @@ static struct i2c_driver tas2764_i2c_driver = { .name = "tas2764", .of_match_table = of_match_ptr(tas2764_of_match), }, - .probe_new = tas2764_i2c_probe, + .probe = tas2764_i2c_probe, .id_table = tas2764_i2c_id, }; module_i2c_driver(tas2764_i2c_driver); diff --git a/sound/soc/codecs/tas2770.c b/sound/soc/codecs/tas2770.c index 8557759acb1f..99bf402eb566 100644 --- a/sound/soc/codecs/tas2770.c +++ b/sound/soc/codecs/tas2770.c @@ -720,7 +720,7 @@ static struct i2c_driver tas2770_i2c_driver = { .name = "tas2770", .of_match_table = of_match_ptr(tas2770_of_match), }, - .probe_new = tas2770_i2c_probe, + .probe = tas2770_i2c_probe, .id_table = tas2770_i2c_id, }; module_i2c_driver(tas2770_i2c_driver); diff --git a/sound/soc/codecs/tas2780.c b/sound/soc/codecs/tas2780.c index 09e7ada1bca4..86bd6c18a944 100644 --- a/sound/soc/codecs/tas2780.c +++ b/sound/soc/codecs/tas2780.c @@ -645,7 +645,7 @@ static struct i2c_driver tas2780_i2c_driver = { .name = "tas2780", .of_match_table = of_match_ptr(tas2780_of_match), }, - .probe_new = tas2780_i2c_probe, + .probe = tas2780_i2c_probe, .id_table = tas2780_i2c_id, }; module_i2c_driver(tas2780_i2c_driver); diff --git a/sound/soc/codecs/tas5086.c b/sound/soc/codecs/tas5086.c index 22143cc5afa7..1b9a79aeac46 100644 --- a/sound/soc/codecs/tas5086.c +++ b/sound/soc/codecs/tas5086.c @@ -990,7 +990,7 @@ static struct i2c_driver tas5086_i2c_driver = { .of_match_table = of_match_ptr(tas5086_dt_ids), }, .id_table = tas5086_i2c_id, - .probe_new = tas5086_i2c_probe, + .probe = tas5086_i2c_probe, .remove = tas5086_i2c_remove, }; diff --git a/sound/soc/codecs/tas571x.c b/sound/soc/codecs/tas571x.c index 84ec1b527646..6022e4c70de1 100644 --- a/sound/soc/codecs/tas571x.c +++ b/sound/soc/codecs/tas571x.c @@ -916,7 +916,7 @@ static struct i2c_driver tas571x_i2c_driver = { .name = "tas571x", .of_match_table = of_match_ptr(tas571x_of_match), }, - .probe_new = tas571x_i2c_probe, + .probe = tas571x_i2c_probe, .remove = tas571x_i2c_remove, .id_table = tas571x_i2c_id, }; diff --git a/sound/soc/codecs/tas5720.c b/sound/soc/codecs/tas5720.c index de6d01c8fdd3..c632d90d0be6 100644 --- a/sound/soc/codecs/tas5720.c +++ b/sound/soc/codecs/tas5720.c @@ -820,7 +820,7 @@ static struct i2c_driver tas5720_i2c_driver = { .name = "tas5720", .of_match_table = of_match_ptr(tas5720_of_match), }, - .probe_new = tas5720_probe, + .probe = tas5720_probe, .id_table = tas5720_id, }; diff --git a/sound/soc/codecs/tas5805m.c b/sound/soc/codecs/tas5805m.c index 4e38eb7acea1..aca3756ffab6 100644 --- a/sound/soc/codecs/tas5805m.c +++ b/sound/soc/codecs/tas5805m.c @@ -597,7 +597,7 @@ MODULE_DEVICE_TABLE(of, tas5805m_of_match); #endif static struct i2c_driver tas5805m_i2c_driver = { - .probe_new = tas5805m_i2c_probe, + .probe = tas5805m_i2c_probe, .remove = tas5805m_i2c_remove, .id_table = tas5805m_i2c_id, .driver = { diff --git a/sound/soc/codecs/tas6424.c b/sound/soc/codecs/tas6424.c index f8ff69fa2549..a07cd1e016e0 100644 --- a/sound/soc/codecs/tas6424.c +++ b/sound/soc/codecs/tas6424.c @@ -803,7 +803,7 @@ static struct i2c_driver tas6424_i2c_driver = { .name = "tas6424", .of_match_table = of_match_ptr(tas6424_of_ids), }, - .probe_new = tas6424_i2c_probe, + .probe = tas6424_i2c_probe, .remove = tas6424_i2c_remove, .id_table = tas6424_i2c_ids, }; diff --git a/sound/soc/codecs/tda7419.c b/sound/soc/codecs/tda7419.c index d964e5207569..e187d74a1737 100644 --- a/sound/soc/codecs/tda7419.c +++ b/sound/soc/codecs/tda7419.c @@ -629,7 +629,7 @@ static struct i2c_driver tda7419_driver = { .name = "tda7419", .of_match_table = tda7419_of_match, }, - .probe_new = tda7419_probe, + .probe = tda7419_probe, .id_table = tda7419_i2c_id, }; diff --git a/sound/soc/codecs/tfa9879.c b/sound/soc/codecs/tfa9879.c index 9f7902ec40db..8cca2ceadd9e 100644 --- a/sound/soc/codecs/tfa9879.c +++ b/sound/soc/codecs/tfa9879.c @@ -312,7 +312,7 @@ static struct i2c_driver tfa9879_i2c_driver = { .name = "tfa9879", .of_match_table = tfa9879_of_match, }, - .probe_new = tfa9879_i2c_probe, + .probe = tfa9879_i2c_probe, .id_table = tfa9879_i2c_id, }; diff --git a/sound/soc/codecs/tfa989x.c b/sound/soc/codecs/tfa989x.c index b853507e65a8..79847a90ac46 100644 --- a/sound/soc/codecs/tfa989x.c +++ b/sound/soc/codecs/tfa989x.c @@ -416,7 +416,7 @@ static struct i2c_driver tfa989x_i2c_driver = { .name = "tfa989x", .of_match_table = tfa989x_of_match, }, - .probe_new = tfa989x_i2c_probe, + .probe = tfa989x_i2c_probe, }; module_i2c_driver(tfa989x_i2c_driver); diff --git a/sound/soc/codecs/tlv320adc3xxx.c b/sound/soc/codecs/tlv320adc3xxx.c index 52bb55724724..b976c1946286 100644 --- a/sound/soc/codecs/tlv320adc3xxx.c +++ b/sound/soc/codecs/tlv320adc3xxx.c @@ -1451,7 +1451,7 @@ static struct i2c_driver adc3xxx_i2c_driver = { .name = "tlv320adc3xxx-codec", .of_match_table = tlv320adc3xxx_of_match, }, - .probe_new = adc3xxx_i2c_probe, + .probe = adc3xxx_i2c_probe, .remove = __exit_p(adc3xxx_i2c_remove), .id_table = adc3xxx_i2c_id, }; diff --git a/sound/soc/codecs/tlv320adcx140.c b/sound/soc/codecs/tlv320adcx140.c index 530f321d08e9..41342b340680 100644 --- a/sound/soc/codecs/tlv320adcx140.c +++ b/sound/soc/codecs/tlv320adcx140.c @@ -1208,7 +1208,7 @@ static struct i2c_driver adcx140_i2c_driver = { .name = "tlv320adcx140-codec", .of_match_table = of_match_ptr(tlv320adcx140_of_match), }, - .probe_new = adcx140_i2c_probe, + .probe = adcx140_i2c_probe, .id_table = adcx140_i2c_id, }; module_i2c_driver(adcx140_i2c_driver); diff --git a/sound/soc/codecs/tlv320aic23-i2c.c b/sound/soc/codecs/tlv320aic23-i2c.c index 1f97673a1cc0..9692ae007c91 100644 --- a/sound/soc/codecs/tlv320aic23-i2c.c +++ b/sound/soc/codecs/tlv320aic23-i2c.c @@ -47,7 +47,7 @@ static struct i2c_driver tlv320aic23_i2c_driver = { .name = "tlv320aic23-codec", .of_match_table = of_match_ptr(tlv320aic23_of_match), }, - .probe_new = tlv320aic23_i2c_probe, + .probe = tlv320aic23_i2c_probe, .id_table = tlv320aic23_id, }; diff --git a/sound/soc/codecs/tlv320aic31xx.c b/sound/soc/codecs/tlv320aic31xx.c index 0847302121f6..9611aa8acb0d 100644 --- a/sound/soc/codecs/tlv320aic31xx.c +++ b/sound/soc/codecs/tlv320aic31xx.c @@ -1746,7 +1746,7 @@ static struct i2c_driver aic31xx_i2c_driver = { .of_match_table = of_match_ptr(tlv320aic31xx_of_match), .acpi_match_table = ACPI_PTR(aic31xx_acpi_match), }, - .probe_new = aic31xx_i2c_probe, + .probe = aic31xx_i2c_probe, .id_table = aic31xx_i2c_id, }; module_i2c_driver(aic31xx_i2c_driver); diff --git a/sound/soc/codecs/tlv320aic32x4-i2c.c b/sound/soc/codecs/tlv320aic32x4-i2c.c index d1e543ca3521..49b33a256cd7 100644 --- a/sound/soc/codecs/tlv320aic32x4-i2c.c +++ b/sound/soc/codecs/tlv320aic32x4-i2c.c @@ -71,7 +71,7 @@ static struct i2c_driver aic32x4_i2c_driver = { .name = "tlv320aic32x4", .of_match_table = aic32x4_of_id, }, - .probe_new = aic32x4_i2c_probe, + .probe = aic32x4_i2c_probe, .remove = aic32x4_i2c_remove, .id_table = aic32x4_i2c_id, }; diff --git a/sound/soc/codecs/tlv320aic3x-i2c.c b/sound/soc/codecs/tlv320aic3x-i2c.c index d7e94d564dbf..bb33fd3dfb4f 100644 --- a/sound/soc/codecs/tlv320aic3x-i2c.c +++ b/sound/soc/codecs/tlv320aic3x-i2c.c @@ -61,7 +61,7 @@ static struct i2c_driver aic3x_i2c_driver = { .name = "tlv320aic3x", .of_match_table = aic3x_of_id, }, - .probe_new = aic3x_i2c_probe, + .probe = aic3x_i2c_probe, .remove = aic3x_i2c_remove, .id_table = aic3x_i2c_id, }; diff --git a/sound/soc/codecs/tlv320dac33.c b/sound/soc/codecs/tlv320dac33.c index 16ce3ef1134b..fa46f51d4341 100644 --- a/sound/soc/codecs/tlv320dac33.c +++ b/sound/soc/codecs/tlv320dac33.c @@ -1560,7 +1560,7 @@ static struct i2c_driver tlv320dac33_i2c_driver = { .driver = { .name = "tlv320dac33-codec", }, - .probe_new = dac33_i2c_probe, + .probe = dac33_i2c_probe, .remove = dac33_i2c_remove, .id_table = tlv320dac33_i2c_id, }; diff --git a/sound/soc/codecs/tpa6130a2.c b/sound/soc/codecs/tpa6130a2.c index 8c00db32996b..5bc486283fde 100644 --- a/sound/soc/codecs/tpa6130a2.c +++ b/sound/soc/codecs/tpa6130a2.c @@ -319,7 +319,7 @@ static struct i2c_driver tpa6130a2_i2c_driver = { .name = "tpa6130a2", .of_match_table = of_match_ptr(tpa6130a2_of_match), }, - .probe_new = tpa6130a2_probe, + .probe = tpa6130a2_probe, .id_table = tpa6130a2_id, }; diff --git a/sound/soc/codecs/ts3a227e.c b/sound/soc/codecs/ts3a227e.c index 5282112c7d8d..6d9166d9116a 100644 --- a/sound/soc/codecs/ts3a227e.c +++ b/sound/soc/codecs/ts3a227e.c @@ -455,7 +455,7 @@ static struct i2c_driver ts3a227e_driver = { .of_match_table = of_match_ptr(ts3a227e_of_match), .acpi_match_table = ACPI_PTR(ts3a227e_acpi_match), }, - .probe_new = ts3a227e_i2c_probe, + .probe = ts3a227e_i2c_probe, .id_table = ts3a227e_i2c_ids, }; module_i2c_driver(ts3a227e_driver); diff --git a/sound/soc/codecs/tscs42xx.c b/sound/soc/codecs/tscs42xx.c index fa0c525189c2..1eefc1fe6ea8 100644 --- a/sound/soc/codecs/tscs42xx.c +++ b/sound/soc/codecs/tscs42xx.c @@ -1503,7 +1503,7 @@ static struct i2c_driver tscs42xx_i2c_driver = { .name = "tscs42xx", .of_match_table = tscs42xx_of_match, }, - .probe_new = tscs42xx_i2c_probe, + .probe = tscs42xx_i2c_probe, .id_table = tscs42xx_i2c_id, }; diff --git a/sound/soc/codecs/tscs454.c b/sound/soc/codecs/tscs454.c index 38622bc247fc..744aef32a21f 100644 --- a/sound/soc/codecs/tscs454.c +++ b/sound/soc/codecs/tscs454.c @@ -3473,7 +3473,7 @@ static struct i2c_driver tscs454_i2c_driver = { .name = "tscs454", .of_match_table = tscs454_of_match, }, - .probe_new = tscs454_i2c_probe, + .probe = tscs454_i2c_probe, .id_table = tscs454_i2c_id, }; diff --git a/sound/soc/codecs/uda1380.c b/sound/soc/codecs/uda1380.c index fdaaee845176..5c5751dc14e5 100644 --- a/sound/soc/codecs/uda1380.c +++ b/sound/soc/codecs/uda1380.c @@ -798,7 +798,7 @@ static struct i2c_driver uda1380_i2c_driver = { .name = "uda1380-codec", .of_match_table = uda1380_of_match, }, - .probe_new = uda1380_i2c_probe, + .probe = uda1380_i2c_probe, .id_table = uda1380_i2c_id, }; diff --git a/sound/soc/codecs/wm1250-ev1.c b/sound/soc/codecs/wm1250-ev1.c index 0064a607ec68..d7eeb41ba60f 100644 --- a/sound/soc/codecs/wm1250-ev1.c +++ b/sound/soc/codecs/wm1250-ev1.c @@ -243,7 +243,7 @@ static struct i2c_driver wm1250_ev1_i2c_driver = { .driver = { .name = "wm1250-ev1", }, - .probe_new = wm1250_ev1_probe, + .probe = wm1250_ev1_probe, .remove = wm1250_ev1_remove, .id_table = wm1250_ev1_i2c_id, }; diff --git a/sound/soc/codecs/wm2000.c b/sound/soc/codecs/wm2000.c index 14b4fd97488c..9571ea53cb3f 100644 --- a/sound/soc/codecs/wm2000.c +++ b/sound/soc/codecs/wm2000.c @@ -938,7 +938,7 @@ static struct i2c_driver wm2000_i2c_driver = { .driver = { .name = "wm2000", }, - .probe_new = wm2000_i2c_probe, + .probe = wm2000_i2c_probe, .id_table = wm2000_i2c_id, }; diff --git a/sound/soc/codecs/wm2200.c b/sound/soc/codecs/wm2200.c index 0a65afa44a59..277b8c468c78 100644 --- a/sound/soc/codecs/wm2200.c +++ b/sound/soc/codecs/wm2200.c @@ -2485,7 +2485,7 @@ static struct i2c_driver wm2200_i2c_driver = { .name = "wm2200", .pm = &wm2200_pm, }, - .probe_new = wm2200_i2c_probe, + .probe = wm2200_i2c_probe, .remove = wm2200_i2c_remove, .id_table = wm2200_i2c_id, }; diff --git a/sound/soc/codecs/wm5100.c b/sound/soc/codecs/wm5100.c index 3b09d4a1684f..a86eacb2a9bb 100644 --- a/sound/soc/codecs/wm5100.c +++ b/sound/soc/codecs/wm5100.c @@ -2709,7 +2709,7 @@ static struct i2c_driver wm5100_i2c_driver = { .name = "wm5100", .pm = &wm5100_pm, }, - .probe_new = wm5100_i2c_probe, + .probe = wm5100_i2c_probe, .remove = wm5100_i2c_remove, .id_table = wm5100_i2c_id, }; diff --git a/sound/soc/codecs/wm8510.c b/sound/soc/codecs/wm8510.c index e13f9780a111..c0ed76d5b65f 100644 --- a/sound/soc/codecs/wm8510.c +++ b/sound/soc/codecs/wm8510.c @@ -678,7 +678,7 @@ static struct i2c_driver wm8510_i2c_driver = { .name = "wm8510", .of_match_table = wm8510_of_match, }, - .probe_new = wm8510_i2c_probe, + .probe = wm8510_i2c_probe, .id_table = wm8510_i2c_id, }; #endif diff --git a/sound/soc/codecs/wm8523.c b/sound/soc/codecs/wm8523.c index 66f6371d8acf..55c72c5ac845 100644 --- a/sound/soc/codecs/wm8523.c +++ b/sound/soc/codecs/wm8523.c @@ -527,7 +527,7 @@ static struct i2c_driver wm8523_i2c_driver = { .name = "wm8523", .of_match_table = wm8523_of_match, }, - .probe_new = wm8523_i2c_probe, + .probe = wm8523_i2c_probe, .id_table = wm8523_i2c_id, }; diff --git a/sound/soc/codecs/wm8580.c b/sound/soc/codecs/wm8580.c index ca796aa0aeb7..34ae7fe05398 100644 --- a/sound/soc/codecs/wm8580.c +++ b/sound/soc/codecs/wm8580.c @@ -1049,7 +1049,7 @@ static struct i2c_driver wm8580_i2c_driver = { .name = "wm8580", .of_match_table = wm8580_of_match, }, - .probe_new = wm8580_i2c_probe, + .probe = wm8580_i2c_probe, .id_table = wm8580_i2c_id, }; diff --git a/sound/soc/codecs/wm8711.c b/sound/soc/codecs/wm8711.c index 383c6796e8a3..903a0147d584 100644 --- a/sound/soc/codecs/wm8711.c +++ b/sound/soc/codecs/wm8711.c @@ -464,7 +464,7 @@ static struct i2c_driver wm8711_i2c_driver = { .name = "wm8711", .of_match_table = wm8711_of_match, }, - .probe_new = wm8711_i2c_probe, + .probe = wm8711_i2c_probe, .id_table = wm8711_i2c_id, }; #endif diff --git a/sound/soc/codecs/wm8728.c b/sound/soc/codecs/wm8728.c index a3dbdbf40723..5ea6d8fd10f6 100644 --- a/sound/soc/codecs/wm8728.c +++ b/sound/soc/codecs/wm8728.c @@ -305,7 +305,7 @@ static struct i2c_driver wm8728_i2c_driver = { .name = "wm8728", .of_match_table = wm8728_of_match, }, - .probe_new = wm8728_i2c_probe, + .probe = wm8728_i2c_probe, .id_table = wm8728_i2c_id, }; #endif diff --git a/sound/soc/codecs/wm8731-i2c.c b/sound/soc/codecs/wm8731-i2c.c index fdf03bf91606..c39e637d813d 100644 --- a/sound/soc/codecs/wm8731-i2c.c +++ b/sound/soc/codecs/wm8731-i2c.c @@ -57,7 +57,7 @@ static struct i2c_driver wm8731_i2c_driver = { .name = "wm8731", .of_match_table = wm8731_of_match, }, - .probe_new = wm8731_i2c_probe, + .probe = wm8731_i2c_probe, .id_table = wm8731_i2c_id, }; diff --git a/sound/soc/codecs/wm8737.c b/sound/soc/codecs/wm8737.c index 90b54343370c..9f4e372e90ea 100644 --- a/sound/soc/codecs/wm8737.c +++ b/sound/soc/codecs/wm8737.c @@ -649,7 +649,7 @@ static struct i2c_driver wm8737_i2c_driver = { .name = "wm8737", .of_match_table = wm8737_of_match, }, - .probe_new = wm8737_i2c_probe, + .probe = wm8737_i2c_probe, .id_table = wm8737_i2c_id, }; #endif diff --git a/sound/soc/codecs/wm8741.c b/sound/soc/codecs/wm8741.c index c7afa4f2795d..787156b980a1 100644 --- a/sound/soc/codecs/wm8741.c +++ b/sound/soc/codecs/wm8741.c @@ -616,7 +616,7 @@ static struct i2c_driver wm8741_i2c_driver = { .name = "wm8741", .of_match_table = wm8741_of_match, }, - .probe_new = wm8741_i2c_probe, + .probe = wm8741_i2c_probe, .id_table = wm8741_i2c_id, }; #endif diff --git a/sound/soc/codecs/wm8750.c b/sound/soc/codecs/wm8750.c index 2f6ee8d6639f..20dc9ff9fea9 100644 --- a/sound/soc/codecs/wm8750.c +++ b/sound/soc/codecs/wm8750.c @@ -813,7 +813,7 @@ static struct i2c_driver wm8750_i2c_driver = { .name = "wm8750", .of_match_table = wm8750_of_match, }, - .probe_new = wm8750_i2c_probe, + .probe = wm8750_i2c_probe, .id_table = wm8750_i2c_id, }; #endif diff --git a/sound/soc/codecs/wm8753.c b/sound/soc/codecs/wm8753.c index bb18f58dc670..5e8a8eb41b2b 100644 --- a/sound/soc/codecs/wm8753.c +++ b/sound/soc/codecs/wm8753.c @@ -1590,7 +1590,7 @@ static struct i2c_driver wm8753_i2c_driver = { .name = "wm8753", .of_match_table = wm8753_of_match, }, - .probe_new = wm8753_i2c_probe, + .probe = wm8753_i2c_probe, .id_table = wm8753_i2c_id, }; #endif diff --git a/sound/soc/codecs/wm8776.c b/sound/soc/codecs/wm8776.c index 936ea24621b0..212224a68006 100644 --- a/sound/soc/codecs/wm8776.c +++ b/sound/soc/codecs/wm8776.c @@ -523,7 +523,7 @@ static struct i2c_driver wm8776_i2c_driver = { .name = "wm8776", .of_match_table = wm8776_of_match, }, - .probe_new = wm8776_i2c_probe, + .probe = wm8776_i2c_probe, .id_table = wm8776_i2c_id, }; #endif diff --git a/sound/soc/codecs/wm8804-i2c.c b/sound/soc/codecs/wm8804-i2c.c index 3ce1a39d76eb..7062a8b2f8b5 100644 --- a/sound/soc/codecs/wm8804-i2c.c +++ b/sound/soc/codecs/wm8804-i2c.c @@ -60,7 +60,7 @@ static struct i2c_driver wm8804_i2c_driver = { .of_match_table = of_match_ptr(wm8804_of_match), .acpi_match_table = ACPI_PTR(wm8804_acpi_match), }, - .probe_new = wm8804_i2c_probe, + .probe = wm8804_i2c_probe, .remove = wm8804_i2c_remove, .id_table = wm8804_i2c_id }; diff --git a/sound/soc/codecs/wm8900.c b/sound/soc/codecs/wm8900.c index 03bbd85ebdf4..320ccd92f318 100644 --- a/sound/soc/codecs/wm8900.c +++ b/sound/soc/codecs/wm8900.c @@ -1295,7 +1295,7 @@ static struct i2c_driver wm8900_i2c_driver = { .driver = { .name = "wm8900", }, - .probe_new = wm8900_i2c_probe, + .probe = wm8900_i2c_probe, .remove = wm8900_i2c_remove, .id_table = wm8900_i2c_id, }; diff --git a/sound/soc/codecs/wm8903.c b/sound/soc/codecs/wm8903.c index 41346e5ec5ad..adaad48ba576 100644 --- a/sound/soc/codecs/wm8903.c +++ b/sound/soc/codecs/wm8903.c @@ -2210,7 +2210,7 @@ static struct i2c_driver wm8903_i2c_driver = { .name = "wm8903", .of_match_table = wm8903_of_match, }, - .probe_new = wm8903_i2c_probe, + .probe = wm8903_i2c_probe, .remove = wm8903_i2c_remove, .id_table = wm8903_i2c_id, }; diff --git a/sound/soc/codecs/wm8904.c b/sound/soc/codecs/wm8904.c index 791d8738d1c0..068e610b1b4c 100644 --- a/sound/soc/codecs/wm8904.c +++ b/sound/soc/codecs/wm8904.c @@ -2337,7 +2337,7 @@ static struct i2c_driver wm8904_i2c_driver = { .name = "wm8904", .of_match_table = of_match_ptr(wm8904_of_match), }, - .probe_new = wm8904_i2c_probe, + .probe = wm8904_i2c_probe, .id_table = wm8904_i2c_id, }; diff --git a/sound/soc/codecs/wm8940.c b/sound/soc/codecs/wm8940.c index 8eb4782c9232..53c27986d216 100644 --- a/sound/soc/codecs/wm8940.c +++ b/sound/soc/codecs/wm8940.c @@ -860,7 +860,7 @@ static struct i2c_driver wm8940_i2c_driver = { .name = "wm8940", .of_match_table = wm8940_of_match, }, - .probe_new = wm8940_i2c_probe, + .probe = wm8940_i2c_probe, .id_table = wm8940_i2c_id, }; diff --git a/sound/soc/codecs/wm8955.c b/sound/soc/codecs/wm8955.c index 05ef45672ebc..78044f580a67 100644 --- a/sound/soc/codecs/wm8955.c +++ b/sound/soc/codecs/wm8955.c @@ -1003,7 +1003,7 @@ static struct i2c_driver wm8955_i2c_driver = { .driver = { .name = "wm8955", }, - .probe_new = wm8955_i2c_probe, + .probe = wm8955_i2c_probe, .id_table = wm8955_i2c_id, }; diff --git a/sound/soc/codecs/wm8960.c b/sound/soc/codecs/wm8960.c index 0d167238a369..366f5d769d6d 100644 --- a/sound/soc/codecs/wm8960.c +++ b/sound/soc/codecs/wm8960.c @@ -1518,7 +1518,7 @@ static struct i2c_driver wm8960_i2c_driver = { .of_match_table = of_match_ptr(wm8960_of_match), .acpi_match_table = ACPI_PTR(wm8960_acpi_match), }, - .probe_new = wm8960_i2c_probe, + .probe = wm8960_i2c_probe, .remove = wm8960_i2c_remove, .id_table = wm8960_i2c_id, }; diff --git a/sound/soc/codecs/wm8961.c b/sound/soc/codecs/wm8961.c index a4857024711d..c076f78d04ce 100644 --- a/sound/soc/codecs/wm8961.c +++ b/sound/soc/codecs/wm8961.c @@ -982,7 +982,7 @@ static struct i2c_driver wm8961_i2c_driver = { .name = "wm8961", .of_match_table = of_match_ptr(wm8961_of_match), }, - .probe_new = wm8961_i2c_probe, + .probe = wm8961_i2c_probe, .id_table = wm8961_i2c_id, }; diff --git a/sound/soc/codecs/wm8962.c b/sound/soc/codecs/wm8962.c index b901e4c65e8a..68ea15be7330 100644 --- a/sound/soc/codecs/wm8962.c +++ b/sound/soc/codecs/wm8962.c @@ -3946,7 +3946,7 @@ static struct i2c_driver wm8962_i2c_driver = { .of_match_table = wm8962_of_match, .pm = &wm8962_pm, }, - .probe_new = wm8962_i2c_probe, + .probe = wm8962_i2c_probe, .remove = wm8962_i2c_remove, .id_table = wm8962_i2c_id, }; diff --git a/sound/soc/codecs/wm8971.c b/sound/soc/codecs/wm8971.c index 4db9248de54b..b22d8f0b59be 100644 --- a/sound/soc/codecs/wm8971.c +++ b/sound/soc/codecs/wm8971.c @@ -700,7 +700,7 @@ static struct i2c_driver wm8971_i2c_driver = { .driver = { .name = "wm8971", }, - .probe_new = wm8971_i2c_probe, + .probe = wm8971_i2c_probe, .id_table = wm8971_i2c_id, }; diff --git a/sound/soc/codecs/wm8974.c b/sound/soc/codecs/wm8974.c index 010a394c705c..044b6f604c09 100644 --- a/sound/soc/codecs/wm8974.c +++ b/sound/soc/codecs/wm8974.c @@ -723,7 +723,7 @@ static struct i2c_driver wm8974_i2c_driver = { .name = "wm8974", .of_match_table = wm8974_of_match, }, - .probe_new = wm8974_i2c_probe, + .probe = wm8974_i2c_probe, .id_table = wm8974_i2c_id, }; diff --git a/sound/soc/codecs/wm8978.c b/sound/soc/codecs/wm8978.c index aa2f55401a88..5c829301cf4c 100644 --- a/sound/soc/codecs/wm8978.c +++ b/sound/soc/codecs/wm8978.c @@ -1072,7 +1072,7 @@ static struct i2c_driver wm8978_i2c_driver = { .name = "wm8978", .of_match_table = wm8978_of_match, }, - .probe_new = wm8978_i2c_probe, + .probe = wm8978_i2c_probe, .id_table = wm8978_i2c_id, }; diff --git a/sound/soc/codecs/wm8983.c b/sound/soc/codecs/wm8983.c index 50e6ac6ccbe0..2bd26e2478d9 100644 --- a/sound/soc/codecs/wm8983.c +++ b/sound/soc/codecs/wm8983.c @@ -1068,7 +1068,7 @@ static struct i2c_driver wm8983_i2c_driver = { .driver = { .name = "wm8983", }, - .probe_new = wm8983_i2c_probe, + .probe = wm8983_i2c_probe, .id_table = wm8983_i2c_id }; #endif diff --git a/sound/soc/codecs/wm8985.c b/sound/soc/codecs/wm8985.c index 751aa6730833..c0816bcfa294 100644 --- a/sound/soc/codecs/wm8985.c +++ b/sound/soc/codecs/wm8985.c @@ -1206,7 +1206,7 @@ static struct i2c_driver wm8985_i2c_driver = { .driver = { .name = "wm8985", }, - .probe_new = wm8985_i2c_probe, + .probe = wm8985_i2c_probe, .id_table = wm8985_i2c_id }; #endif diff --git a/sound/soc/codecs/wm8988.c b/sound/soc/codecs/wm8988.c index 5dbdf647cd97..b440719cca7d 100644 --- a/sound/soc/codecs/wm8988.c +++ b/sound/soc/codecs/wm8988.c @@ -905,7 +905,7 @@ static struct i2c_driver wm8988_i2c_driver = { .driver = { .name = "wm8988", }, - .probe_new = wm8988_i2c_probe, + .probe = wm8988_i2c_probe, .id_table = wm8988_i2c_id, }; #endif diff --git a/sound/soc/codecs/wm8990.c b/sound/soc/codecs/wm8990.c index 589af286f133..5a8e765090af 100644 --- a/sound/soc/codecs/wm8990.c +++ b/sound/soc/codecs/wm8990.c @@ -1247,7 +1247,7 @@ static struct i2c_driver wm8990_i2c_driver = { .driver = { .name = "wm8990", }, - .probe_new = wm8990_i2c_probe, + .probe = wm8990_i2c_probe, .id_table = wm8990_i2c_id, }; diff --git a/sound/soc/codecs/wm8991.c b/sound/soc/codecs/wm8991.c index 30121993b7b4..8cb2ae829699 100644 --- a/sound/soc/codecs/wm8991.c +++ b/sound/soc/codecs/wm8991.c @@ -1323,7 +1323,7 @@ static struct i2c_driver wm8991_i2c_driver = { .driver = { .name = "wm8991", }, - .probe_new = wm8991_i2c_probe, + .probe = wm8991_i2c_probe, .id_table = wm8991_i2c_id, }; diff --git a/sound/soc/codecs/wm8993.c b/sound/soc/codecs/wm8993.c index 22a47acbc6d1..feb997c698e2 100644 --- a/sound/soc/codecs/wm8993.c +++ b/sound/soc/codecs/wm8993.c @@ -1741,7 +1741,7 @@ static struct i2c_driver wm8993_i2c_driver = { .driver = { .name = "wm8993", }, - .probe_new = wm8993_i2c_probe, + .probe = wm8993_i2c_probe, .remove = wm8993_i2c_remove, .id_table = wm8993_i2c_id, }; diff --git a/sound/soc/codecs/wm8995.c b/sound/soc/codecs/wm8995.c index eed48bf339f2..90588614edcc 100644 --- a/sound/soc/codecs/wm8995.c +++ b/sound/soc/codecs/wm8995.c @@ -2268,7 +2268,7 @@ static struct i2c_driver wm8995_i2c_driver = { .driver = { .name = "wm8995", }, - .probe_new = wm8995_i2c_probe, + .probe = wm8995_i2c_probe, .id_table = wm8995_i2c_id }; #endif diff --git a/sound/soc/codecs/wm8996.c b/sound/soc/codecs/wm8996.c index b52ed89d631a..5d0eb0ae0475 100644 --- a/sound/soc/codecs/wm8996.c +++ b/sound/soc/codecs/wm8996.c @@ -3086,7 +3086,7 @@ static struct i2c_driver wm8996_i2c_driver = { .driver = { .name = "wm8996", }, - .probe_new = wm8996_i2c_probe, + .probe = wm8996_i2c_probe, .remove = wm8996_i2c_remove, .id_table = wm8996_i2c_id, }; diff --git a/sound/soc/codecs/wm9081.c b/sound/soc/codecs/wm9081.c index 513ec0ba81bb..34a07db7342a 100644 --- a/sound/soc/codecs/wm9081.c +++ b/sound/soc/codecs/wm9081.c @@ -1369,7 +1369,7 @@ static struct i2c_driver wm9081_i2c_driver = { .driver = { .name = "wm9081", }, - .probe_new = wm9081_i2c_probe, + .probe = wm9081_i2c_probe, .remove = wm9081_i2c_remove, .id_table = wm9081_i2c_id, }; diff --git a/sound/soc/codecs/wm9090.c b/sound/soc/codecs/wm9090.c index ef3524c3f07f..432729c753dd 100644 --- a/sound/soc/codecs/wm9090.c +++ b/sound/soc/codecs/wm9090.c @@ -616,7 +616,7 @@ static struct i2c_driver wm9090_i2c_driver = { .driver = { .name = "wm9090", }, - .probe_new = wm9090_i2c_probe, + .probe = wm9090_i2c_probe, .id_table = wm9090_id, }; base-commit: 457391b0380335d5e9a5babdec90ac53928b23b4 -- 2.39.2

1 0

[PATCH] ALSA: emu10k1: fix multi-channel playback device class
by Oswald Buddenhagen 25 Apr '23

25 Apr '23

It's multi, not mono/stereo. AFAICT, this doesn't do anything in the kernel. Also, I think the subclass is meaningless for devices with just one stream, but whatever. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- sound/pci/emu10k1/emupcm.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/sound/pci/emu10k1/emupcm.c b/sound/pci/emu10k1/emupcm.c index 87c3b19c6b2d..c04ef6ea188e 100644 --- a/sound/pci/emu10k1/emupcm.c +++ b/sound/pci/emu10k1/emupcm.c @@ -1377,7 +1377,8 @@ int snd_emu10k1_pcm_multi(struct snd_emu10k1 *emu, int device) snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_PLAYBACK, &snd_emu10k1_efx_playback_ops); pcm->info_flags = 0; - pcm->dev_subclass = SNDRV_PCM_SUBCLASS_GENERIC_MIX; + pcm->dev_class = SNDRV_PCM_CLASS_MULTI; + pcm->dev_subclass = SNDRV_PCM_SUBCLASS_MULTI_MIX; strcpy(pcm->name, "Multichannel Playback"); emu->pcm_multi = pcm; -- 2.40.0.152.g15d061e6df

2 5

Fix gigabyte z690i aorus ultra ALC-4080
by GitHub pull_request - opened 25 Apr '23

25 Apr '23

alsa-project/alsa-ucm-conf pull request #307 was opened from jameson-reed: Currently the board is not matched by the regex. Once matched the config still isn't valid. I've got it stable with the following changes, disabling spdif and line1 and updating Mic1PCM value. The front headphone and microphone jacks are working now, as is the rear audio out. That does leave 1 jack on the back I haven't had any luck with. There is no spdif on the board. Request URL : https://github.com/alsa-project/alsa-ucm-conf/pull/307 Patch URL : https://github.com/alsa-project/alsa-ucm-conf/pull/307.patch Repository URL: https://github.com/alsa-project/alsa-ucm-conf

1 0

[PATCH v2] ASoC: max98090: make it selectable
by Maxim Kochetkov 24 Apr '23

24 Apr '23

There is no way to select max98090 from menuconfig right now. Add a Kconfig menu description to allow building the driver standalone. It will allow this codec to be used by any other I2S master without adding extra sound card entry in Kconfig. Signed-off-by: Maxim Kochetkov <fido_max(a)inbox.ru> --- sound/soc/codecs/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 79d2362ad055..8020097d4e4c 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -1090,7 +1090,7 @@ config SND_SOC_MAX98088 depends on I2C config SND_SOC_MAX98090 - tristate + tristate "Maxim MAX98090 CODEC" depends on I2C config SND_SOC_MAX98095 -- 2.39.2

3 7

[PATCH] ASoC: Intel: soc-acpi-byt: Fix "WM510205" match no longer working
by Hans de Goede 24 Apr '23

24 Apr '23

Commit 7e1d728a94ca ("ASoC: Intel: soc-acpi-byt: Add new WM5102 ACPI HID") added an extra HID to wm5102_comp_ids.codecs, but it forgot to bump wm5102_comp_ids.num_codecs, causing the last codec HID in the codecs list to no longer work. Bump wm5102_comp_ids.num_codecs to fix this. Fixes: 7e1d728a94ca ("ASoC: Intel: soc-acpi-byt: Add new WM5102 ACPI HID") Signed-off-by: Hans de Goede <hdegoede(a)redhat.com> --- sound/soc/intel/common/soc-acpi-intel-byt-match.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/intel/common/soc-acpi-intel-byt-match.c b/sound/soc/intel/common/soc-acpi-intel-byt-match.c index db5a92b9875a..87c44f284971 100644 --- a/sound/soc/intel/common/soc-acpi-intel-byt-match.c +++ b/sound/soc/intel/common/soc-acpi-intel-byt-match.c @@ -124,7 +124,7 @@ static const struct snd_soc_acpi_codecs rt5640_comp_ids = { }; static const struct snd_soc_acpi_codecs wm5102_comp_ids = { - .num_codecs = 2, + .num_codecs = 3, .codecs = { "10WM5102", "WM510204", "WM510205"}, }; -- 2.39.2

3 2

[PATCH] ASoC: SOF: Intel: hda-stream: Move three variable assignments behind condition checks in hda_dsp_iccmax_stream_hw_params()
by Markus Elfring 24 Apr '23

24 Apr '23

Date: Wed, 19 Apr 2023 20:42:19 +0200 The address of a data structure member was determined before a corresponding null pointer check in the implementation of the function “hda_dsp_iccmax_stream_hw_params”. Thus avoid the risk for undefined behaviour by moving the assignment for three local variables behind some condition checks. This issue was detected by using the Coccinelle software. Fixes: 7d88b9608142f95ccdd3dfb190da4a5faddb1cc7 ("ASoC: SOF: Intel: hdac_ext_stream: consistent prefixes for variables/members") Signed-off-by: Markus Elfring <elfring(a)users.sourceforge.net> --- sound/soc/sof/intel/hda-stream.c | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-) diff --git a/sound/soc/sof/intel/hda-stream.c b/sound/soc/sof/intel/hda-stream.c index 79d818e6a0fa..9c44127014fc 100644 --- a/sound/soc/sof/intel/hda-stream.c +++ b/sound/soc/sof/intel/hda-stream.c @@ -407,10 +407,10 @@ int hda_dsp_iccmax_stream_hw_params(struct snd_sof_dev *sdev, struct hdac_ext_st struct snd_dma_buffer *dmab, struct snd_pcm_hw_params *params) { - struct hdac_stream *hstream = &hext_stream->hstream; - int sd_offset = SOF_STREAM_SD_OFFSET(hstream); + struct hdac_stream *hstream; + int sd_offset; int ret; - u32 mask = 0x1 << hstream->index; + u32 mask; if (!hext_stream) { dev_err(sdev->dev, "error: no stream available\n"); @@ -422,9 +422,12 @@ int hda_dsp_iccmax_stream_hw_params(struct snd_sof_dev *sdev, struct hdac_ext_st return -ENODEV; } + hstream = &hext_stream->hstream; if (hstream->posbuf) *hstream->posbuf = 0; + sd_offset = SOF_STREAM_SD_OFFSET(hstream); + /* reset BDL address */ snd_sof_dsp_write(sdev, HDA_DSP_HDA_BAR, sd_offset + SOF_HDA_ADSP_REG_SD_BDLPL, @@ -459,6 +462,8 @@ int hda_dsp_iccmax_stream_hw_params(struct snd_sof_dev *sdev, struct hdac_ext_st sd_offset + SOF_HDA_ADSP_REG_SD_LVI, 0xffff, (hstream->frags - 1)); + mask = 0x1 << hstream->index; + /* decouple host and link DMA, enable DSP features */ snd_sof_dsp_update_bits(sdev, HDA_DSP_PP_BAR, SOF_HDA_REG_PP_PPCTL, mask, mask); -- 2.40.0

2 2

[PATCH v6 0/7] Add the Lantiq PEF2256 audio support
by Herve Codina 24 Apr '23

24 Apr '23

Hi, This series adds support for audio using the Lantiq PEF2256 framer. The Lantiq PEF2256 is a framer and line interface component designed to fulfill all required interfacing between an analog E1/T1/J1 line and the digital PCM system highway/H.100 bus. The first part of this series (patches 1 to 4) adds the Lantiq PEF2256 driver core fixing a MFD core issue at patch 2. The patch 5 adds the PEF2256 pinmux support. The patch 6 adds the audio support using the Lantiq PEF2256 driver core. The last patch adds myself as the PEF2256 maintainer. The consumer/provider relation between the codec and the driver core allows to use the PEF2256 framer for other purpose than audio support. Compared to the previous iteration https://lore.kernel.org/all/20230328092645.634375-1-herve.codina@bootlin.co… This v6 series mainly: - Use regmap - Move the pinmux part to the pinctrl subsystem - Move register definitions to header files. - Split pef2256_setup_e1() in several parts. - Fixed issues raised by checkpatch.pl. - Removed debug prints. Best regards, Herve Codina Changes v5 -> v6 - Patch 1 Add 'Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski(a)linaro.org>' - Patch 2 New patch added fixing an MFD core issue. - Patch 3 (patch 2 in v5) Remove the pinmux part. Move registers definition to a header file and rework the definition. Use a regmap for register accesses Various minor fixes (typos, comments, ...) Fixed issues raised by checkpatch.pl --strict Removed debug prints. - Patch 4 (patch 3 in v5) No changes - Patch 5 New patch adding the PEF2256 pinmux part in the pinctrl subsystem. - Patch 6 (patch 4 in v5) Fixed issues raised by checkpatch.pl --strict - Patch 7 (patch 5 in v5) Updated according to files creation and move. Changes v4 -> v5 - Patch 1 Fix 'additionalProperties' and 'unevaluatedProperties' positions Fix sub-nodes names suffixes Changes v3 -> v4 - Patch 1 Merge the codec sub-node description. Move the 'allOf' property after the 'required' property. Rework the example to be more complete. - Patches 2 and 5 Drop of_match_ptr() - Patch 2 Add 'depends on OF' as pinconf_generic_dt_node_to_map_pin() needs OF support to be compiled (error raised by the kernel test robot). - Patch 4 Remove patch (merged in patch 1) Changes v2 -> v3 - Patch 1 Remove unneeded 'allOf' and quotes. Add several 'additionalProperties: false' Fix example (node name, interrupts and reg properties) Replace the lantiq,sysclk-rate-hz property by sclkr and sclkx clocks. Define 'lantiq,frame-format' property in top level. Move to MFD - Patch 2 Fix some #define. Compact the register accessor helpers. Rework pef2256_get_version(). Merge v1.2 and v2.x GCM setup functions into one pef2256_setup_gcm(). Update comments, avoid duplicates and change some conditionals. Remove the carrier spinlock and use atomic_t. Make exported symbol consistent and use EXPORT_SYMBOL_GPL. Remove the no more needed pef2256_get_byphandle() and devm_pef2256_get_byphandle(). Replace the lantiq,sysclk-rate-hz property by sclkr and sclkx clocks. Move to MFD - Patch 4 Remove, merged with patch 7 - Patch 4 (patch 5 in v2) Update title and description. Remove incorrect SPI reference. Remove the 'lantiq,pef2256' phandle. Fix commit log - Patch 5 (patch 6 in v2) Remove devm_pef2256_get_byphandle(). Fix commit log - Patch 6 (patch 7 in v2) Merge v2 patch 4. One entry only for PEF2256 Changes v1 -> v2 - Patch 2 Remove duplicate const qualifiers. Add HAS_IOMEM as a dependency - Patch 3 Fix a "Block quote ends without a blank line; unexpected unindent" syntax issue. Herve Codina (7): dt-bindings: mfd: Add the Lantiq PEF2256 E1/T1/J1 framer mfd: core: Ensure disabled devices are skiped without aborting mfd: Add support for the Lantiq PEF2256 framer Documentation: sysfs: Document the Lantiq PEF2256 sysfs entry pinctrl: Add support for the Lantic PEF2256 pinmux ASoC: codecs: Add support for the Lantiq PEF2256 codec MAINTAINERS: Add the Lantiq PEF2256 driver entry .../sysfs-bus-platform-devices-pef2256 | 12 + .../bindings/mfd/lantiq,pef2256.yaml | 267 +++++ MAINTAINERS | 12 + drivers/mfd/Kconfig | 16 + drivers/mfd/Makefile | 1 + drivers/mfd/mfd-core.c | 18 +- drivers/mfd/pef2256-regs.h | 250 +++++ drivers/mfd/pef2256.c | 950 ++++++++++++++++++ drivers/pinctrl/Kconfig | 14 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/pinctrl-pef2256-regs.h | 65 ++ drivers/pinctrl/pinctrl-pef2256.c | 310 ++++++ include/linux/mfd/pef2256.h | 52 + sound/soc/codecs/Kconfig | 14 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/pef2256-codec.c | 390 +++++++ 16 files changed, 2369 insertions(+), 5 deletions(-) create mode 100644 Documentation/ABI/testing/sysfs-bus-platform-devices-pef2256 create mode 100644 Documentation/devicetree/bindings/mfd/lantiq,pef2256.yaml create mode 100644 drivers/mfd/pef2256-regs.h create mode 100644 drivers/mfd/pef2256.c create mode 100644 drivers/pinctrl/pinctrl-pef2256-regs.h create mode 100644 drivers/pinctrl/pinctrl-pef2256.c create mode 100644 include/linux/mfd/pef2256.h create mode 100644 sound/soc/codecs/pef2256-codec.c -- 2.39.2

4 18

[PATCH 0/7] ALSA: emu10k1: improvements mostly related to #defines
by Oswald Buddenhagen 24 Apr '23

24 Apr '23

Mostly adding, removing, and otherwise massaging numerous #defines and code using them, and surrounding comments. Oswald Buddenhagen (7): ALSA: emu10k1: comment updates ALSA: emu10k1: fix lineup of EMU_HANA_* defines ALSA: emu10k1: eliminate some unused defines ALSA: emu10k1: remove some bogus defines ALSA: emu10k1: pull in some register definitions from kX-project ALSA: emu10k1: fixup DSP defines ALSA: emu10k1: use more existing defines instead of open-coded numbers include/sound/emu10k1.h | 685 +++++++++++++-------------- include/uapi/sound/emu10k1.h | 147 ++++-- sound/pci/emu10k1/emu10k1.c | 11 - sound/pci/emu10k1/emu10k1_callback.c | 15 +- sound/pci/emu10k1/emu10k1_main.c | 125 ++--- sound/pci/emu10k1/emufx.c | 18 +- sound/pci/emu10k1/emumixer.c | 13 +- sound/pci/emu10k1/emupcm.c | 39 +- sound/pci/emu10k1/io.c | 26 +- sound/pci/emu10k1/p16v.c | 29 +- sound/pci/emu10k1/p16v.h | 2 +- sound/pci/emu10k1/p17v.h | 4 +- 12 files changed, 554 insertions(+), 560 deletions(-) -- 2.40.0.152.g15d061e6df

3 11

[GIT PULL] ASoC updates for v6.4
by Mark Brown 24 Apr '23

24 Apr '23

The following changes since commit e3720f92e0237921da537e47a0b24e27899203f8: ASoC: SOF: avoid a NULL dereference with unsupported widgets (2023-03-29 14:40:18 +0100) are available in the Git repository at: https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git tags/asoc-v6.4 for you to fetch changes up to dc801ea8ae37d54706e6f1cef140731ac5981c9c: ASoC: fsl: imx-audmix: remove dummy dai_link->platform (2023-04-21 13:45:07 +0100) ---------------------------------------------------------------- ASoC: Updates for v6.4 The bulk of the commits here are for the conversion of drivers to use void remove callbacks but there's a reasonable amount of other stuff going on, the pace of development with the SOF code continues to be high and there's a bunch of new drivers too: - More core cleanups from Morimto-san. - Update drivers to have remove() callbacks returning void, mostly mechanical with some substantial changes. - Continued feature and simplification work on SOF, including addition of a no-DSP mode for bringup, HDA MLink and extensions to the IPC4 protocol. - Hibernation support for CS35L45. - More DT binding conversions. - Support for Cirrus Logic CS35L56, Freescale QMC, Maxim MAX98363, nVidia systems with MAX9809x and RT5631, Realtek RT712, Renesas R-Car Gen4, Rockchip RK3588 and TI TAS5733. ---------------------------------------------------------------- Aashish Sharma (1): ASoC: mediatek: common: Fix refcount leak in parse_dai_link_info Ajye Huang (1): ASoC: Intel: sof_rt5682: Enable Bluetooth offload on adl_rt1019_rt5682 Alexander Stein (2): ASoC: fsl: define a common DRIVER_NAME ASoC: fsl: Specify driver name in ASoC card Alexander Sverdlin (5): ASoC: ep93xx: i2s: move enable call to startup callback ASoC: cs4271: flat regcache, trivial simplifications ASoC: ep93xx: i2s: Make it individually selectable ASoC: ep93xx: Add I2S description ASoC: ep93xx: Add OF support Allen-KH Cheng (1): ASoC: mediatek: mt8186: Move some prints to debug level André Morishita (1): ASoC: dt-bindings: maxim,max98371: Convert to DT schema Baishan Jiang (1): ASoC: amd: yc: Add ThinkBook 14 G5+ ARP to quirks list for acp6x Bard Liao (4): ASoC: SOF: ipc4-topology: don't allocate blob if it will not be used ASoC: Intel: sof_sdw: set codec_num = 1 if the device is not aggregated ASoC: Intel: sof_sdw: support different devices on the same sdw link ASoC: Intel: sof_sdw: append codec type to dai link name Benjamin Bara (1): ASoC: maxim,max9867: add "mclk" support Cem Kaya (1): ASoC: amd: Add Dell G15 5525 to quirks list Chancel Liu (1): ASoC: dt-bindings: wlf,wm8524: Convert to json-schema Chao Song (3): ASoC: SOF: sof-audio: add support for setting up loopback routes ASoC: SOF: ipc4-topology: add base module config extension structure ASoC: SOF: ipc4-topology: set copier output format for process module Charles Keepax (1): ASoC: wm8903: Remove outdated DMIC comment Christophe JAILLET (3): ASoC: meson: Use the devm_clk_get_optional() helper ASoC: da7218: Use devm_clk_get_optional() ASoC: fsl: Simplify an error message Claudiu Beznea (8): ASoC: mchp-spdiftx: use FIELD_PREP() where possible ASoC: mchp-spdiftx: use regmap_update_bits() ASoC: mchp-spdiftx: update debug message ASoC: mchp-pdmc: use FIELD_PREP() where possible ASoC: mchp-pdmc: return directly ret ASoC: mchp-pdmc: avoid casting to/from void pointer MAINTAINERS: add myself as maintainer for Microchip AT91 sound drivers MAINTAINERS: update Microchip AT91 sound entries with documentation files Colin Ian King (1): ASoC: SOF: ipc4/intel: Fix spelling mistake "schduler" -> "scheduler" Cristian Ciocaltea (7): ASoC: dt-bindings: everest,es8316: Document audio graph port ASoC: dt-bindings: rockchip: Document audio graph port ASoC: dt-bindings: rockchip: i2s-tdm: Document audio graph port ASoC: dt-bindings: rockchip: i2s-tdm: Document power-domains ASoC: dt-bindings: rockchip: Add compatible for RK3588 ASoC: rockchip: i2s: Add compatible for RK3588 ASoC: es8316: Handle optional IRQ assignment Curtis Malainey (5): ASoC: SOF: loader: Remove log prefixes for snd_sof_run_firmware ASoC: Intel: Add rpl_mx98360_rt5682 driver ASoC: SOF: ipc: Add no reply inline calls ASoC: SOF: Use no_reply calls for TX ASoC: Intel: sof_cirrus_common: Guard against missing buses Daniel Baluta (1): ASoC: soc-compress: Inherit atomicity from DAI link for Compress FE David Heidelberg (1): ASoC: nvidia,tegra-audio: add RT5631 CODEC David Lin (2): ASoC: dt-bindings: nau8825: Add delay control for input path ASoC: nau8825: Add delay control for input path David Rau (1): ASoC: da7219: Improve the relability of AAD IRQ process Fred Oh (1): ASoC: SOF: Intel: mtl: fix page fault in dspless mode when DSP is disabled Geert Uytterhoeven (1): ASoC: dt-bindings: renesas: rsnd: Update example Gustavo A. R. Silva (1): ASoC: SOF: ipc4-topology: Replace fake flexible arrays with flexible-array member Harshit Mogalapalli (1): ASoC: cs35l56: Remove redundant return statement in cs35l56_spi_probe() Herve Codina (13): dt-bindings: soc: fsl: cpm_qe: Add TSA controller soc: fsl: cpm1: Add support for TSA MAINTAINERS: add the Freescale TSA controller entry powerpc/8xx: Use a larger CPM1 command check mask dt-bindings: soc: fsl: cpm_qe: Add QMC controller soc: fsl: cpm1: Add support for QMC MAINTAINERS: add the Freescale QMC controller entry dt-bindings: sound: Add support for QMC audio ASoC: fsl: Add support for QMC audio MAINTAINERS: add the Freescale QMC audio entry dt-bindings: soc: fsl: cpm_qe: cpm1-scc-qmc: Remove unneeded property dt-bindings: soc: fsl: cpm_qe: cpm1-tsa: Remove unneeded property soc: fsl: cpm1: qmc: Fix test dependency Herve Codina via Alsa-devel (1): soc: fsl: cpm1: qmc: Fix assigned timeslot masks Jacob Keller (1): ASoC: Intel: avs: Use struct_size for struct avs_modcfg_ext size Jianhua Lu (1): ASoC: cs35l41: Add 12288000 clk freq to cs35l41_fs_mon clk config Jiapeng Chong (2): ASoC: tegra: remove unneeded semicolon ASoC: cs35l56: Fix an unsigned comparison which can never be negative Johan Hovold (1): ASoC: qcom: audioreach: drop stray 'get' from error message Jyri Sarha (3): ASoC: SOF: ipc4: Add macros for chain-dma message bits ASoC: SOF: ipc4/intel: Add support for chained DMA ASoC: SOF: ipc4/intel: Add missing mutex_unlock() Kai Vehmanen (3): ASoC: SOF: ipc4-mtrace: process pending logs upon FW crash ASoC: SOF: ipc4-pcm: support multiple configs for BE DAIs ASoC: SOF: ipc4-topology: use common helper function in copier prepare Kamel Bouhara (2): ASoC: tas571x: add tas5733 compatible ASoC: tas571x: add support for TAS5733 Krzysztof Kozlowski (32): ASoC: dt-bindings: wlf,wm8960: Convert to dtschema ASoC: dt-bindings: qcom,wcd934x: Reference dai-common ASoC: dt-bindings: qcom,wcd9335: Convert to dtschema ASoC: codecs: adau1977-spi: Mark OF related data as maybe unused ASoC: codecs: pcm179x-spi: Mark OF related data as maybe unused ASoC: codecs: rt1019: Mark OF related data as maybe unused ASoC: codecs: src4xxx-i2c: Mark OF related data as maybe unused ASoC: codecs: zl38060: Mark OF related data as maybe unused ASoC: dt-bindings: adi,adau17x1: fix indentation and example ASoC: dt-bindings: renesas: rsnd: correct comments syntax ASoC: dt-bindings: wlf,wm8994: Convert to dtschema ASoC: dt-bindings: qcom,lpass-rx-macro: narrow clocks per variants ASoC: dt-bindings: qcom,lpass-rx-macro: Add SM8550 RX macro ASoC: codecs: lpass-rx-macro: add support for SM8550 ASoC: dt-bindings: qcom,lpass-tx-macro: narrow clocks per variants ASoC: dt-bindings: qcom,lpass-tx-macro: Add SM8550 TX macro ASoC: codecs: lpass-tx-macro: add support for SM8550 ASoC: dt-bindings: qcom,lpass-wsa-macro: Add SM8550 WSA macro ASoC: codecs: lpass-wsa-macro: add support for SM8550 ASoC: codecs: lpass-rx-macro: add support for SM8550 ASoC: codecs: lpass-tx-macro: add support for SM8550 ASoC: dt-bindings: qcom,lpass-va-macro: Add SM8550 VA macro ASoC: dt-bindings: qcom,lpass-wsa-macro: Add SM8550 WSA macro ASoC: codecs: lpass-wsa-macro: add support for SM8550 ASoC: dt-bindings: qcom,lpass-va-macro: Add SM8550 VA macro ASoC: dt-bindings: qcom,lpass-rx-macro: correct minItems for clocks ASoC: dt-bindings: qcom,lpass-va-macro: Add missing NPL clock ASoC: dt-bindings: asahi-kasei,ak4458: fix missing quotes around hash ASoC: codecs: wcd9335: Simplify with dev_err_probe ASoC: codecs: wcd934x: Simplify with dev_err_probe ASoC: codecs: wcd934x: Simplify &pdev->dev in probe ASoC: codecs: wcd938x: Simplify with dev_err_probe Kuninori Morimoto (27): ASoC: dt-bindings: renesas,rsnd.yaml: add R-Car Gen4 support ASoC: soc-core.c: remove useless dev_dbg() ASoC: soc-dai.c: add missing flag check at snd_soc_pcm_dai_probe() ASoC: soc-pcm.c: remove indirect runtime copy ASoC: simple-card: add comment to indicate don't remove platforms ASoC: fsl: remove unnecessary dai_link->platform ASoC: atmel: remove unnecessary dai_link->platform ASoC: ti: remove unnecessary dai_link->platform ASoC: soc-topology.c: remove unnecessary dai_link->platform ASoC: simple-card.c: add missing of_node_put() ASoC: audio-graph-card2-custom-sample.dtsi: use card->name to avoid long name ASoC: soc-core.c: add snd_soc_add_pcm_runtimes() ASoC: soc-topology.c: dai_link->platform again ASoC: soc-topology.c: dai_link->platform again ASoC: soc.h: clarify Codec2Codec params ASoC: audio-graph-card2: switch to use c2c_params instead of params ASoC: meson: switch to use c2c_params instead of params ASoC: samsung: switch to use c2c_params instead of params ASoC: soc.h: remove unused params/num_params ASoC: soc-dapm.c: tidyup dapm_connect_dai_pair() ASoC: expand snd_soc_dapm_mutex_lock/unlock() ASoC: expand snd_soc_dpcm_mutex_lock/unlock() ASoC: add snd_soc_card_mutex_lock/unlock() ASoC: fsl: imx-es8328: cleanup platform which is using Generic DMA ASoC: fsl: imx-spdif: cleanup platform which is using Generic DMA ASoC: fsl: imx-audmix: cleanup platform which is using Generic DMA ASoC: fsl: imx-audmix: remove dummy dai_link->platform Lad Prabhakar (2): ASoC: dt-bindings: renesas,rz-ssi: Update interrupts and interrupt-names properties ASoC: sh: rz-ssi: Update interrupt handling for half duplex channels Libin Yang (4): ASoC: SOF: ipc4-control: set_volume_data only applies to VOLSW family ASoC: SOF: ipc4-topology: Add support for TPLG_CTL_BYTES ASoC: SOF: ipc4-topology: add effect widget support ASoC: SOF: ipc4-topology: update pipeline_params in process prepare Liliang Ye (1): ASoC: fsl_mqs: move of_node_put() to the correct location Lucas Tanure (14): ASoC: cs35l41: Only disable internal boost ASoC: cs35l41: Refactor error release code ALSA: cs35l41: Add shared boost feature ASoC: dt-bindings: cirrus,cs35l41: Document CS35l41 shared boost ASoC: amd: vangogh: Remove unnecessary init function ASoC: amd: vangogh: Small code refactor ASoC: amd: vangogh: use sizeof of variable instead of struct type ASoC: amd: vangogh: remove unnecessarily included headers ASoC: amd: vangogh: use for_each_rtd_components instead of for ASoC: amd: vangogh: Check Bit Clock rate before snd_soc_dai_set_pll ASoC: amd: vangogh: Move nau8821 and CPU side code up for future platform ASoC: amd: vangogh: Centralize strings definition ASoC: amd: vangogh: Add components prefix in structs and function names ASoC: cs35l41: Steam Deck Shared boost properties quirk Mark Brown (43): Add the PowerQUICC audio support using the QMC SoC: SOF: Intel: hda/mtl: Improve and enable DMI L1 RZ/G2L SSI: Update interrupt numbers ASoC: microchip: some cleanups for AT91 sound drivers Add support for the TAS5733 Add "mclk" support for maxim,max9867 Refactor Vangogh acp5x machine driver Add CS35L41 shared boost feature ASoC: SOF: ipc4: Add core_id support from topology ASoC: SOF: Intel: hda: Introduce HDA DAI abstraction Merge tag 'v6.3-rc2' into asoc-6.4 to fix clock related boot issues ASoC: Merge up fixes as a dependency for future SOF work ASoC: mediatek: fix coverity problems ASoC: SOF: ipc4: Add support for bytes control ASoC: SOF: ipc4: Add support for formats per pins ASoC: mt8192: Address spammy log messages ASoC: SOF: ipc4: upport multiple configs for BE DAIs ASoC: SOF: ipc4-topology: Add support for effect Fix sound on ASUS Transformers Enable I2S support for RK3588/RK3588S SoCs ALSA/ASoC: Convert to platform remove callback ASoC: Initial support for Cirrus Logic CS35L56 ASoC: SOF: ipc4/intel: Support for ChainDMA ASoC: SOF: pcm/Intel: Handle IPC dependent sequencing ASoC: Intel: sof_rt5682: Updates for MTL BT offload ASoC: remove unnecessary dai_link->platform ASoC: add audio digital codecs for Qualcomm SM8550 ASoC: Merge fixes ASoC: dapm: Sort speakers after other outputs ASoC: SoundWire codecs: simplify/fix set_stream ASoC: SOF: core/Intel: Introduce DSPless mode ASoC: clarify Codec2Codec params ASoC: qcom: fixes for Click/Pop Noise ASoC: ep93xx: Prepare for DT transition ASoC: SOF: Intel: hda-mlink: HDaudio multi-link ASoC: cs35l56: Add system suspend handling ASoC: cleanup mutex lock ASoC: cs35l56: Code improvements ASoC: cs35l56: Updates for B0 silicon ASoC: es8316: Don't use ranges based register lookup for a single register ASoC: Intel: boards: updates for 6.4 ASoC: SOF: add no_reply IPC calls ASoC: SOF: pcm/Intel: Pause-resume improvements for Nícolas F. R. A. Prado (1): ASoC: mt8192: Move spammy messages to debug level Nícolas F. R. A. Prado via Alsa-devel (1): ASoC: mt8192: Remove function name log messages Otabek Nazrullaev (1): ASoC: dt-bindings: maxim,max9759: Convert to DT schema. Paweł Anikiel (1): ASoC: ssm2602: Add support for CLKDIV2 Peter Ujfalusi (23): ASoC: SOF: ipc4: Add macro to set the core_id in create_pipe message ASoC: SOF: ipc4-topology: Add support for core_id for pipelines ASoC: SOF: Intel: MTL: Don't access EM2 ASoC: SOF: ipc3-control: Rename snd_sof_refresh_control() ASoC: SOF: ipc3-control: Merge functions to handle bytes_ext get variants ASoC: SOF: uapi: header: Convert sof_abi_hdr comments to kernel style ASoC: SOF: uapi: header: Update sof_abi_hdr doc for IPC4 use ASoC: SOF: ipc4-control: Add support for bytes control get and put ASoC: SOF: ipc4-topology: Move the kcontrol module_id update to helper ASoC: SOF: ipc4-topology: Initialize in_format to NULL in sof_ipc4_get_audio_fmt ASoC: SOF: ipc4-control: Return on error in sof_ipc4_widget_kcontrol_setup() ASoC: SOF: Intel: hda-stream: Do not dereference hstream until it is safe ASoC: SOF: Add flag and state which will be used for DSP-less mode ASoC: SOF: Add support for DSPless mode ASoC: SOF: Intel: hda: Skip interfaces not supported on a platform ASoC: SOF: Intel: hda: Add support for DSPless mode ASoC: SOF: Intel: pci-apl: Allow DSPless mode ASoC: SOF: Intel: pci-cnl: Allow DSPless mode ASoC: SOF: Intel: pci-icl: Allow DSPless mode ASoC: SOF: Intel: pci-mtl: Allow DSPless mode ASoC: SOF: Intel: pci-skl: Allow DSPless mode ASoC: SOF: Intel: pci-tgl: Allow DSPless mode ASoC: SOF: Intel: hda-dai: Print the format_val as hexadecimal number Pierre-Louis Bossart (34): ASoC: SOF: Intel: hda-loader: use SOF helper for consistency ASoC: codecs: cs42l42-sdw: clear stream ASoC: codecs: sdw-mockup: simplify set_stream ASoC: codecs: max98373-sdw: simplify set_stream ASoC: codecs: rt1308-sdw: simplify set_stream ASoC: codecs: rt1316-sdw: simplify set_stream ASoC: codecs: rt1318-sdw: simplify set_stream ASoC: codecs: rt700-sdw: simplify set_stream ASoC: codecs: rt711-sdw: simplify set_stream ASoC: codecs: rt711-sdca: simplify set_stream ASoC: codecs: rt712-sdca: simplify set_stream ASoC: codecs: rt715: simplify set_stream ASoC: codecs: rt715-sdca: simplify set_stream ASoC: codecs: rt5682-sdw: simplify set_stream ASoC: SOF: Intel: hda: make DSPless mode work with DSP disabled in BIOS ASoC: SOF: Intel: hda: add __func__ in SoundWire lcount() error logs Documentation: sound: add description of Intel HDaudio multi-links ALSA: hda: add HDaudio Extended link definitions ASoC: SOF: Intel: hda-mlink: improve hda_bus_ml_free() helper ASoC: SOF: Intel: hda-mlink: add return value for hda_bus_ml_get_capabilities() ASoC: SOF: Intel: hda-mlink: move to a dedicated module ASoC: SOF: Intel: hda-mlink: add structures to parse ALT links ASoC: SOF: Intel: hda-mlink: special-case HDaudio regular links ASoC: SOF: Intel: hda-mlink: introduce helpers for 'extended links' PM ASoC: SOF: Intel: hda-mlink: add convenience helpers for SoundWire PM ASoC: SOF: Intel: hda-mlink: add helper to return sublink count ASoC: SOF: Intel: hda-mlink: add helpers to enable/check interrupts ASoC: SOF: Intel: hda-mlink: add helpers to set link SYNC frequency ASoC: SOF: Intel: hda-mlink: add helpers for sync_arm/sync_go ASoC: SOF: Intel: hda-mlink: add helper to check cmdsync ASoC: SOF: Intel: hda-mlink: program SoundWire LSDIID registers ASoC: SOF: Intel: hda-mlink: add helpers to retrieve DMIC/SSP hlink ASoC: SOF: Intel: hda-mlink: add helper to offload link ownership ASoC: SOF: Intel: hda-mlink: add helper to retrieve eml_lock Prajna Sariputra (1): ASoC: amd: yc: Add DMI entries to support HP OMEN 16-n0xxx (8A42) Rander Wang (1): ASoC: SOF: ipc4-topology: add core token in each module extended token list Ranjani Sridharan (36): ASoC: SOF: Intel: hda: Do not re-enable L1 if disabled before suspend ASoC: SOF: Intel: hda: Restrict DMI L1 disable workaround ASoC: SOF: Intel: MTL: Enable DMI L1 ASoC: SOF: Intel: hda-dai: Remove BE DAI DRV ops for SSP DAI's ASoC: SOF: Intel: hda-dai: Remove hda_link_dma_params() ASoC: SOF: Intel: hda-dai: remove struct hda_pipe_params ASoC: SOF: Intel: hda-dai: Modify the signature of hda_link_dma_cleanup() ASoC: SOF: Intel: hda-dai: Pass the CPU dai pointer ASoC: SOF: Intel: hda-dai: Use the dai argument in ipc4_hda_dai_trigger ASoC: SOF: Intel: hda-dai: Introduce DAI widget ops ASoC: SOF: Intel: hda-dai: Define and set the HDA DAI widget DMA ops ASoC: SOF: Intel: hda-dai: Add setup_hext_stream/reset_hext_stream DMA ops ASoC: SOF: Intel: hda-dai: Use the topology IPC dai_config op ASoC: SOF: Intel: hda-dai: Define DAI widget DMA trigger ops for IPC4 ASoC: SOF: Intel: hda: Unify DAI drv ops for IPC3 and IPC4 ASoC: SOF: Intel: hda: Remove hda_ctrl_dai_widget_setup/free() ASoC: SOF: Intel: hda: remove redundant DAI config during hw_free ASoC: SOF: rename a couple of tokens ASoC: SOF: Use input/output pin consistently ASoC: SOF: ipc4-topology: Add a new field in struct sof_ipc4_available_audio_format ASoC: SOF: ipc4-topology: Do not parse the DMA_BUFFER_SIZE token ASoC: SOF: ipc4-topology: Parse the SOF_COMP_TOKENS only once ASoC: SOF: ipc4-topology: Always parse the output formats in topology ASoC: SOF: ipc4-topology: Modify the type of available input/output formats ASoC: SOF: ipc4-topology: Modify the signature of sof_ipc4_init_audio_fmt() ASoC: SOF: ipc4-topology: Remove the ref_audio_fmt field ASoC: SOF: ipc4-topology: Add new tokens for input/output pin format count ASoC: SOF: ipc4-topology: Search only pin 0 formats ASoC: SOF: ipc4-topology: Add support for base config extension ASoC: SOF: topology: Set pipeline widget before updating IPC structures ASoC: SOF: Intel: hda-dai: Do not perform DMA cleanup during stop ASoC: SOF: pcm: Make hw_params reset conditional for IPC3 ASoC: SOF: pcm: Improve the pcm trigger sequence ASoC: SOF: Intel: hda: Do not stop/start DMA during pause/release ASoC: SOF: pcm: Add an option to skip platform trigger during stop ASoC: SOF: Intel: Split the set_power_op for IPC3 and IPC4 Richard Fitzgerald (11): ASoC: cs35l56: Add driver for Cirrus Logic CS35L56 ASoC: cs35l56: Use DAPM widget for firmware PLAY/PAUSE ASoC: cs35l56: Skip first init_completion wait in dsp_work if init_done ASoC: cs35l56: Always wait for firmware boot in runtime-resume ASoC: cs35l56: Add basic system suspend handling ASoC: cs35l56: Remove quick-cancelling of dsp_work() ASoC: cs35l56: Re-patch firmware after system suspend ASoC: cs35l56: Update comment on masking of EINT20 interrupts ASoC: cs35l56: Remove SDW1 TX5 and TX6 ASoC: cs35l56: Remove SDW2RX1 mixer source ASoC: cs35l56: Rename mixer source defines for SoundWire DP1 Richard Leitner (3): ASoC: dt-bindings: maxim,max9867: convert txt bindings to yaml ASoC: dt-bindings: maxim,max9867: add clocks property ASoC: dt-bindings: maxim,max9867: fix example Rob Herring (3): ASoC: Use of_property_present() for testing DT property presence ASoC: Use of_property_read_bool() for boolean properties ASoC: dt-bindings: Drop unneeded quotes Ryan Lee (2): ASoC: max98363: add soundwire amplifier driver ASoC: dt-bindings: max98363: add soundwire amplifier Saalim Quadri (10): ASoC: dt-bindings: ak5558: Convert to dtschema ASoC: dt-bindings: alc5632: Convert to dtschema ASoC: dt-bindings: ak4458: Convert to dtschema ASoC: dt-bindings: wm8510: Convert to dtschema ASoC: dt-bindings: wm8580: Convert to dtschema ASoC: dt-bindings: wm8711: Convert to dtschema ASoC: dt-bindings: wm8523: Convert to dtschema ASoC: dt-bindings: wm8753: Convert to dtschema ASoC: dt-bindings: wm8737: Convert to dtschema ASoC: dt-bindings: wm8728: Convert to dtschema Seven Lee (1): ASoC: nau8821: Implement DRC controls Shengjiu Wang (1): ASoC: fsl: Restore configuration of platform Shuming Fan (1): ASoC: rt712-sdca: Add RT712 SDCA driver for Mic topology Simon Trimmer (14): firmware: cs_dsp: Introduce no_core_startstop for self-booting DSPs ASoC: wm_adsp: Use no_core_startstop to prevent creating preload control firmware: cs_dsp: Support DSPs that don't require firmware download ASoC: wm_adsp: Support DSPs that don't require firmware download ASoC: wm_adsp: Expose the DSP boot work actions as wm_adsp_power_up() ASoC: wm_adsp: Add support for loading bin files without wmfw ASoC: wm_adsp: Simplify the logging of requested firmware files firmware: cs_dsp: Add a debugfs entry containing control details ASoC: cs35l56: Rework IRQ allocation ASoC: cs35l56: Allow a wider range for reset pulse width ASoC: cs35l56: Wait for init_complete in cs35l56_component_probe() ASoC: cs35l56: Remove redundant dsp_ready_completion ASoC: cs35l56: Don't return a value from cs35l56_remove() ASoC: cs35l56: Remove duplicate mbox log messages Srinivas Kandagatla (3): ASoC: qcom: common: add kcontrol to jack pins ASoC: qcom: q6apm-lpass-dai: close graphs before opening a new one ASoC: qcom: sdw: do not restart soundwire ports for every prepare Svyatoslav Ryhel (6): ASoC: jack: allow multiple interrupt per gpio ASoC: tegra: Support coupled mic-hp detection ASoC: tegra: Support RT5631 by machine driver ASoC: tegra: Support MAX9808x by machine driver ASoC: nvidia,tegra-audio-common: add coupled-mic-hp-detect property ASoC: nvidia,tegra-audio: add MAX9808x CODEC Syed Saba Kareem (2): ASoC: amd: ps: update the acp clock source. ASoC: amd: Add check for acp config flags Tom Rix (4): ASoC: SMA1303: set sma_i2c_regmap storage-class-specifier to static ASoC: max98363: Make soc_codec_dev_max98363 static ASoC: mediatek: mt8186: set variable aud_pinctrl to static ASoC: nau8825: fix bounds check for adc_delay Trevor Wu (4): ASoC: mediatek: mt8195: add dai id check before accessing array ASoC: mediatek: mt9195-mt6359: fix UNINIT problem ASoC: mediatek: mt6358: fix UNINIT problem ASoC: mediatek: mt6359: fix UNINIT problem Uday M Bhat (2): ASoC: Intel: sof_rt5682: Update BT offload config for Rex ASoC: Intel: sof_rt5682: Update BT offload config for MTL RVP Uwe Kleine-König (172): ALSA: sh: aica: Drop if blocks with always false condition ASoC: amd: acp: rembrandt: Drop if blocks with always false condition ALSA: pxa2xx: Convert to platform remove callback returning void ALSA: atmel: ac97: Convert to platform remove callback returning void ALSA: mts64: Convert to platform remove callback returning void ALSA: portman2x4: Convert to platform remove callback returning void ALSA: mips/hal2: Convert to platform remove callback returning void ALSA: mips/sgio2audio: Convert to platform remove callback returning void ALSA: hda/tegra: Convert to platform remove callback returning void ALSA: ppc/powermac: Convert to platform remove callback returning void ALSA: sh: aica: Convert to platform remove callback returning void ALSA: sh_dac_audio: Convert to platform remove callback returning void ASoC: adi: axi-i2s: Convert to platform remove callback returning void ASoC: adi: axi-spdif: Convert to platform remove callback returning void ASoC: amd: acp-pcm-dma: Convert to platform remove callback returning void ASoC: amd: acp: rembrandt: Convert to platform remove callback returning void ASoC: amd: acp: renoir: Convert to platform remove callback returning void ASoC: amd: ps: Convert to platform remove callback returning void ASoC: amd: raven: acp3x-pcm-dma: Convert to platform remove callback returning void ASoC: amd: raven: acp3x-pdm-dma: Convert to platform remove callback returning void ASoC: amd: vangogh: acp5x-pcm-dma: Convert to platform remove callback returning void ASoC: amd: yc: acp6x-pdm-dma: Convert to platform remove callback returning void ASoC: apple: mca: Convert to platform remove callback returning void ASoC: atmel: atmel-i2s: Convert to platform remove callback returning void ASoC: atmel: atmel_wm8904: Convert to platform remove callback returning void ASoC: atmel: mchp-i2s-mcc: Convert to platform remove callback returning void ASoC: atmel: mchp-pdmc: Convert to platform remove callback returning void ASoC: atmel: mchp-spdifrx: Convert to platform remove callback returning void ASoC: atmel: mchp-spdiftx: Convert to platform remove callback returning void ASoC: atmel: mikroe-proto: Convert to platform remove callback returning void ASoC: atmel: sam9g20_wm8731: Convert to platform remove callback returning void ASoC: atmel: sam9x5_wm8731: Convert to platform remove callback returning void ASoC: atmel: tse850-pcm5142: Convert to platform remove callback returning void ASoC: au1x: ac97c: Convert to platform remove callback returning void ASoC: au1x: i2sc: Convert to platform remove callback returning void ASoC: au1x: psc-ac97: Convert to platform remove callback returning void ASoC: au1x: psc-i2s: Convert to platform remove callback returning void ASoC: bcm: bcm63xx-i2s-whistler: Convert to platform remove callback returning void ASoC: bcm: cygnus-ssp: Convert to platform remove callback returning void ASoC: cirrus: edb93xx: Convert to platform remove callback returning void ASoC: cirrus: ep93xx-i2s: Convert to platform remove callback returning void ASoC: codecs: cs47l15: Convert to platform remove callback returning void ASoC: codecs: cs47l24: Convert to platform remove callback returning void ASoC: codecs: cs47l35: Convert to platform remove callback returning void ASoC: codecs: cs47l85: Convert to platform remove callback returning void ASoC: codecs: cs47l90: Convert to platform remove callback returning void ASoC: codecs: cs47l92: Convert to platform remove callback returning void ASoC: codecs: inno_rk3036: Convert to platform remove callback returning void ASoC: codecs: lpass-rx-macro: Convert to platform remove callback returning void ASoC: codecs: lpass-tx-macro: Convert to platform remove callback returning void ASoC: codecs: lpass-va-macro: Convert to platform remove callback returning void ASoC: codecs: lpass-wsa-macro: Convert to platform remove callback returning void ASoC: codecs: msm8916-wcd-analog: Convert to platform remove callback returning void ASoC: codecs: msm8916-wcd-digital: Convert to platform remove callback returning void ASoC: codecs: rk817_codec: Convert to platform remove callback returning void ASoC: codecs: wcd938x: Convert to platform remove callback returning void ASoC: codecs: wm5102: Convert to platform remove callback returning void ASoC: codecs: wm5110: Convert to platform remove callback returning void ASoC: codecs: wm8994: Convert to platform remove callback returning void ASoC: codecs: wm8997: Convert to platform remove callback returning void ASoC: codecs: wm8998: Convert to platform remove callback returning void ASoC: dwc: dwc-i2s: Convert to platform remove callback returning void ASoC: fsl: eukrea-tlv320: Convert to platform remove callback returning void ASoC: fsl: fsl_asrc: Convert to platform remove callback returning void ASoC: fsl: fsl_aud2htx: Convert to platform remove callback returning void ASoC: fsl: fsl_audmix: Convert to platform remove callback returning void ASoC: fsl: fsl_dma: Convert to platform remove callback returning void ASoC: fsl: fsl_easrc: Convert to platform remove callback returning void ASoC: fsl: fsl_esai: Convert to platform remove callback returning void ASoC: fsl: fsl_mqs: Convert to platform remove callback returning void ASoC: fsl: fsl_rpmsg: Convert to platform remove callback returning void ASoC: fsl: fsl_sai: Convert to platform remove callback returning void ASoC: fsl: fsl_spdif: Convert to platform remove callback returning void ASoC: fsl: fsl_ssi: Convert to platform remove callback returning void ASoC: fsl: fsl_xcvr: Convert to platform remove callback returning void ASoC: fsl: imx-audmux: Convert to platform remove callback returning void ASoC: fsl: imx-pcm-rpmsg: Convert to platform remove callback returning void ASoC: fsl: imx-sgtl5000: Convert to platform remove callback returning void ASoC: fsl: mpc5200_psc_ac97: Convert to platform remove callback returning void ASoC: fsl: mpc5200_psc_i2s: Convert to platform remove callback returning void ASoC: fsl: mpc8610_hpcd: Convert to platform remove callback returning void ASoC: fsl: p1022_ds: Convert to platform remove callback returning void ASoC: fsl: p1022_rdk: Convert to platform remove callback returning void ASoC: fsl: pcm030-audio-fabric: Convert to platform remove callback returning void ASoC: generic: test-component: Convert to platform remove callback returning void ASoC: img: img-i2s-in: Convert to platform remove callback returning void ASoC: img: img-i2s-out: Convert to platform remove callback returning void ASoC: img: img-parallel-out: Convert to platform remove callback returning void ASoC: img: img-spdif-in: Convert to platform remove callback returning void ASoC: img: img-spdif-out: Convert to platform remove callback returning void ASoC: img: pistachio-internal-dac: Convert to platform remove callback returning void ASoC: Intel: sst-mfld-platform-pcm: Convert to platform remove callback returning void ASoC: Intel: sst: Convert to platform remove callback returning void ASoC: Intel: bytcht_es8316: Convert to platform remove callback returning void ASoC: Intel: bytcr_rt5640: Convert to platform remove callback returning void ASoC: Intel: boards: bytcr_rt5651: Convert to platform remove callback returning void ASoC: Intel: bytcr_wm5102: Convert to platform remove callback returning void ASoC: Intel: cht_bsw_max98090_ti: Convert to platform remove callback returning void ASoC: Intel: sof_es8336: Convert to platform remove callback returning void ASoC: Intel: sof_pcm512x: Convert to platform remove callback returning void ASoC: Intel: sof_sdw: Convert to platform remove callback returning void ASoC: Intel: sof_wm8804: Convert to platform remove callback returning void ASoC: Intel: catpt: Convert to platform remove callback returning void ASoC: Intel: skl-ssp-clk: Convert to platform remove callback returning void ASoC: kirkwood: kirkwood-i2s: Convert to platform remove callback returning void ASoC: mediatek: mtk-btcvsd: Convert to platform remove callback returning void ASoC: mediatek: mt2701-afe-pcm: Convert to platform remove callback returning void ASoC: mediatek: mt6797-afe-pcm: Convert to platform remove callback returning void ASoC: mediatek: mt8173-afe-pcm: Convert to platform remove callback returning void ASoC: mediatek: mt8183-afe-pcm: Convert to platform remove callback returning void ASoC: mediatek: mt8188-afe-pcm: Convert to platform remove callback returning void ASoC: mediatek: mt8192-afe-pcm: Convert to platform remove callback returning void ASoC: mediatek: mt8195-afe-pcm: Convert to platform remove callback returning void ASoC: meson: aiu: Convert to platform remove callback returning void ASoC: mxs: mxs-sgtl5000: Convert to platform remove callback returning void ASoC: pxa: mmp-sspa: Convert to platform remove callback returning void ASoC: pxa: pxa2xx-ac97: Convert to platform remove callback returning void ASoC: qcom: qdsp6: Convert to platform remove callback returning void ASoC: rockchip: rockchip_i2s: Convert to platform remove callback returning void ASoC: rockchip: rockchip_pdm: Convert to platform remove callback returning void ASoC: rockchip: rockchip_rt5645: Convert to platform remove callback returning void ASoC: rockchip: rockchip_spdif: Convert to platform remove callback returning void ASoC: samsung: arndale: Convert to platform remove callback returning void ASoC: samsung: i2s: Convert to platform remove callback returning void ASoC: samsung: odroid: Convert to platform remove callback returning void ASoC: samsung: pcm: Convert to platform remove callback returning void ASoC: samsung: snow: Convert to platform remove callback returning void ASoC: samsung: spdif: Convert to platform remove callback returning void ASoC: sh: fsi: Convert to platform remove callback returning void ASoC: sh: hac: Convert to platform remove callback returning void ASoC: sh: rcar: Convert to platform remove callback returning void ASoC: sh: rz-ssi: Convert to platform remove callback returning void ASoC: sh: siu_dai: Convert to platform remove callback returning void ASoC: sprd: sprd-mcdt: Convert to platform remove callback returning void ASoC: stm: stm32_adfsdm: Convert to platform remove callback returning void ASoC: stm: stm32_i2s: Convert to platform remove callback returning void ASoC: stm: stm32_sai_sub: Convert to platform remove callback returning void ASoC: stm: stm32_spdifrx: Convert to platform remove callback returning void ASoC: sunxi: sun4i-codec: Convert to platform remove callback returning void ASoC: sunxi: sun4i-i2s: Convert to platform remove callback returning void ASoC: sunxi: sun4i-spdif: Convert to platform remove callback returning void ASoC: sunxi: sun50i-dmic: Convert to platform remove callback returning void ASoC: sunxi: sun8i-codec: Convert to platform remove callback returning void ASoC: tegra: tegra186_asrc: Convert to platform remove callback returning void ASoC: tegra: tegra186_dspk: Convert to platform remove callback returning void ASoC: tegra: tegra20_ac97: Convert to platform remove callback returning void ASoC: tegra: tegra20_i2s: Convert to platform remove callback returning void ASoC: tegra: tegra210_admaif: Convert to platform remove callback returning void ASoC: tegra: tegra210_adx: Convert to platform remove callback returning void ASoC: tegra: tegra210_ahub: Convert to platform remove callback returning void ASoC: tegra: tegra210_amx: Convert to platform remove callback returning void ASoC: tegra: tegra210_dmic: Convert to platform remove callback returning void ASoC: tegra: tegra210_i2s: Convert to platform remove callback returning void ASoC: tegra: tegra210_mixer: Convert to platform remove callback returning void ASoC: tegra: tegra210_mvc: Convert to platform remove callback returning void ASoC: tegra: tegra210_ope: Convert to platform remove callback returning void ASoC: tegra: tegra210_sfc: Convert to platform remove callback returning void ASoC: tegra: tegra30_ahub: Convert to platform remove callback returning void ASoC: tegra: tegra30_i2s: Convert to platform remove callback returning void ASoC: ti: ams-delta: Convert to platform remove callback returning void ASoC: ti: davinci-i2s: Convert to platform remove callback returning void ASoC: ti: davinci-mcasp: Convert to platform remove callback returning void ASoC: ti: omap-hdmi: Convert to platform remove callback returning void ASoC: ti: omap-mcbsp: Convert to platform remove callback returning void ASoC: uniphier: evea: Convert to platform remove callback returning void ASoC: ux500: mop500: Convert to platform remove callback returning void ASoC: ux500: ux500_msp_dai: Convert to platform remove callback returning void ASoC: xilinx: xlnx_formatter_pcm: Convert to platform remove callback returning void ASoC: xilinx: xlnx_spdif: Convert to platform remove callback returning void ASoC: xtensa: xtfpga-i2s: Convert to platform remove callback returning void ALSA: sparc/cs4231: Convert to platform remove callback returning void ALSA: sparc/dbri: Convert to platform remove callback returning void V sujith kumar Reddy (2): ASoC: SOF: amd: Add pcm pointer callback for amd platforms. ASoC: SOF: amd: Enable cont_update_posn variable in pcm hw_params. Vijaya Anand (1): ASoC: dt-bindings: adi,adau17x1: Convert to DT schema Vijendar Mukunda (6): ASoC: SOF: amd: remove unused code ASoC: SOF: amd: remove acp_dai_probe() function ASoC: SOF: amd: remove unused variables ASoC: SOF: amd: refactor get_chip_info callback ASoC: SOF: amd: refactor error checks in probe call ASoC: SOF: amd: refactor dmic codec platform device creation Vlad.Karpovich (5): ASoC: cs35l45: Support for GPIO pins configuration. ASoC: dt-bindings: cs35l45: GPIOs configuration ASoC: cs35l45: IRQ support ASoC: cs35l45: DSP Support ASoC: cs35l45: Hibernation support Ying Liu (1): ASoC: tas5720: add missing unwind goto in tas5720_codec_probe Yong Zhi (5): ASoC: SOF: Intel: mtl: Access MTL_HFPWRCTL from HDA_DSP_BAR ASoC: Intel: sof_rt5682: Remove conditional dpcm_capture setting ASoC: SOF: Intel: MTL: conditionally wake WPIO1PG domain ASoC: Intel: sof_sdw: remove late_probe flag in struct sof_sdw_codec_info ASoC: Intel: sof_sdw_max98373: change sof_sdw_mx8373_late_probe to static call Zihao Wang (1): ASoC: tegra20_ac97: Add missing unwind goto in tegra20_ac97_platform_probe() apoorv (1): ASoC: Intel: soc-acpi: Add entry for rt711-sdca-sdw at link 2 in RPL match table .../bindings/soc/fsl/cpm_qe/fsl,cpm1-scc-qmc.yaml | 162 ++ .../bindings/soc/fsl/cpm_qe/fsl,cpm1-tsa.yaml | 205 +++ .../devicetree/bindings/sound/adi,adau1372.yaml | 2 +- .../devicetree/bindings/sound/adi,adau17x1.txt | 32 - .../devicetree/bindings/sound/adi,adau17x1.yaml | 52 + .../devicetree/bindings/sound/adi,max98363.yaml | 60 + .../devicetree/bindings/sound/adi,max98396.yaml | 8 +- Documentation/devicetree/bindings/sound/ak4458.txt | 28 - Documentation/devicetree/bindings/sound/ak5558.txt | 24 - .../devicetree/bindings/sound/alc5632.txt | 43 - .../bindings/sound/asahi-kasei,ak4458.yaml | 73 + .../bindings/sound/asahi-kasei,ak5558.yaml | 48 + .../bindings/sound/audio-graph-port.yaml | 22 +- .../devicetree/bindings/sound/audio-graph.yaml | 8 +- .../devicetree/bindings/sound/cirrus,cs35l41.yaml | 10 +- .../devicetree/bindings/sound/cirrus,cs35l45.yaml | 80 +- .../devicetree/bindings/sound/cirrus,cs42l42.yaml | 12 +- .../bindings/sound/cirrus,ep9301-i2s.yaml | 66 + .../devicetree/bindings/sound/everest,es8316.yaml | 4 + .../devicetree/bindings/sound/fsl,qmc-audio.yaml | 117 ++ .../devicetree/bindings/sound/max98371.txt | 17 - .../devicetree/bindings/sound/max9867.txt | 17 - .../devicetree/bindings/sound/maxim,max9759.txt | 18 - .../devicetree/bindings/sound/maxim,max9759.yaml | 45 + .../devicetree/bindings/sound/maxim,max98371.yaml | 42 + .../devicetree/bindings/sound/maxim,max9867.yaml | 60 + .../devicetree/bindings/sound/mt8186-afe-pcm.yaml | 6 +- .../sound/mt8186-mt6366-da7219-max98357.yaml | 2 +- .../sound/mt8186-mt6366-rt1019-rt5682s.yaml | 2 +- .../devicetree/bindings/sound/mt8192-afe-pcm.yaml | 6 +- .../sound/mt8192-mt6359-rt1015-rt5682.yaml | 4 +- .../devicetree/bindings/sound/mt8195-afe-pcm.yaml | 2 +- .../devicetree/bindings/sound/mt8195-mt6359.yaml | 8 +- .../devicetree/bindings/sound/nau8825.txt | 3 + .../bindings/sound/nvidia,tegra-audio-alc5632.yaml | 8 +- .../bindings/sound/nvidia,tegra-audio-common.yaml | 4 + .../sound/nvidia,tegra-audio-max9808x.yaml | 90 ++ .../sound/nvidia,tegra-audio-max98090.yaml | 8 +- .../bindings/sound/nvidia,tegra-audio-rt5631.yaml | 85 ++ .../bindings/sound/nvidia,tegra-audio-rt5640.yaml | 6 +- .../bindings/sound/nvidia,tegra-audio-rt5677.yaml | 26 +- .../sound/nvidia,tegra-audio-sgtl5000.yaml | 6 +- .../bindings/sound/nvidia,tegra-audio-wm8753.yaml | 6 +- .../bindings/sound/nvidia,tegra-audio-wm8903.yaml | 8 +- .../bindings/sound/nvidia,tegra-audio-wm9712.yaml | 8 +- .../bindings/sound/qcom,lpass-rx-macro.yaml | 77 +- .../bindings/sound/qcom,lpass-tx-macro.yaml | 81 +- .../bindings/sound/qcom,lpass-va-macro.yaml | 86 +- .../bindings/sound/qcom,lpass-wsa-macro.yaml | 23 +- .../devicetree/bindings/sound/qcom,q6asm-dais.yaml | 2 +- .../devicetree/bindings/sound/qcom,wcd9335.txt | 123 -- .../devicetree/bindings/sound/qcom,wcd9335.yaml | 156 ++ .../devicetree/bindings/sound/qcom,wcd934x.yaml | 1 + .../devicetree/bindings/sound/realtek,alc5632.yaml | 63 + .../devicetree/bindings/sound/renesas,rsnd.yaml | 129 +- .../devicetree/bindings/sound/renesas,rz-ssi.yaml | 21 +- .../bindings/sound/rockchip,i2s-tdm.yaml | 7 + .../devicetree/bindings/sound/rockchip-i2s.yaml | 5 + .../devicetree/bindings/sound/sgtl5000.yaml | 6 +- .../devicetree/bindings/sound/simple-card.yaml | 2 +- .../bindings/sound/socionext,uniphier-aio.yaml | 2 +- .../devicetree/bindings/sound/tas571x.txt | 1 + .../devicetree/bindings/sound/wlf,wm8510.yaml | 41 + .../devicetree/bindings/sound/wlf,wm8523.yaml | 40 + .../devicetree/bindings/sound/wlf,wm8524.yaml | 40 + .../devicetree/bindings/sound/wlf,wm8580.yaml | 42 + .../devicetree/bindings/sound/wlf,wm8711.yaml | 40 + .../devicetree/bindings/sound/wlf,wm8728.yaml | 40 + .../devicetree/bindings/sound/wlf,wm8737.yaml | 40 + .../devicetree/bindings/sound/wlf,wm8753.yaml | 62 + .../devicetree/bindings/sound/wlf,wm8960.yaml | 88 ++ .../devicetree/bindings/sound/wlf,wm8994.yaml | 194 +++ Documentation/devicetree/bindings/sound/wm8510.txt | 18 - Documentation/devicetree/bindings/sound/wm8523.txt | 16 - Documentation/devicetree/bindings/sound/wm8524.txt | 16 - Documentation/devicetree/bindings/sound/wm8580.txt | 16 - Documentation/devicetree/bindings/sound/wm8711.txt | 18 - Documentation/devicetree/bindings/sound/wm8728.txt | 18 - Documentation/devicetree/bindings/sound/wm8737.txt | 18 - Documentation/devicetree/bindings/sound/wm8753.txt | 40 - Documentation/devicetree/bindings/sound/wm8960.txt | 42 - Documentation/devicetree/bindings/sound/wm8994.txt | 112 -- Documentation/sound/hd-audio/index.rst | 1 + Documentation/sound/hd-audio/intel-multi-link.rst | 312 ++++ MAINTAINERS | 36 +- arch/powerpc/platforms/8xx/cpm1.c | 2 +- drivers/firmware/cirrus/cs_dsp.c | 48 +- drivers/soc/fsl/qe/Kconfig | 23 + drivers/soc/fsl/qe/Makefile | 2 + drivers/soc/fsl/qe/qmc.c | 1537 +++++++++++++++++++ drivers/soc/fsl/qe/tsa.c | 846 +++++++++++ drivers/soc/fsl/qe/tsa.h | 42 + include/dt-bindings/soc/cpm1-fsl,tsa.h | 13 + include/dt-bindings/sound/cs35l45.h | 57 + include/linux/firmware/cirrus/cs_dsp.h | 1 + include/soc/fsl/qe/qmc.h | 71 + include/sound/cs35l41.h | 13 +- include/sound/cs35l56.h | 266 ++++ include/sound/hda-mlink.h | 166 ++ include/sound/hda_register.h | 40 +- include/sound/soc-card.h | 17 +- include/sound/soc-dapm.h | 5 - include/sound/soc-dpcm.h | 1 - include/sound/soc.h | 119 +- include/sound/sof.h | 5 + include/sound/sof/ipc4/header.h | 33 + include/uapi/sound/sof/abi.h | 2 + include/uapi/sound/sof/header.h | 27 +- include/uapi/sound/sof/tokens.h | 21 +- sound/arm/pxa2xx-ac97.c | 6 +- sound/atmel/ac97c.c | 6 +- sound/drivers/mts64.c | 6 +- sound/drivers/portman2x4.c | 6 +- sound/mips/hal2.c | 5 +- sound/mips/sgio2audio.c | 5 +- sound/pci/hda/cs35l41_hda.c | 6 +- sound/pci/hda/hda_tegra.c | 6 +- sound/ppc/powermac.c | 5 +- sound/sh/aica.c | 7 +- sound/sh/sh_dac_audio.c | 5 +- sound/soc/adi/axi-i2s.c | 6 +- sound/soc/adi/axi-spdif.c | 6 +- sound/soc/amd/Kconfig | 2 + sound/soc/amd/acp-pcm-dma.c | 6 +- sound/soc/amd/acp/acp-rembrandt.c | 13 +- sound/soc/amd/acp/acp-renoir.c | 5 +- sound/soc/amd/ps/acp63.h | 2 + sound/soc/amd/ps/pci-ps.c | 10 +- sound/soc/amd/ps/ps-pdm-dma.c | 5 +- sound/soc/amd/raven/acp3x-pcm-dma.c | 5 +- sound/soc/amd/renoir/acp3x-pdm-dma.c | 5 +- sound/soc/amd/vangogh/acp5x-mach.c | 297 ++-- sound/soc/amd/vangogh/acp5x-pcm-dma.c | 5 +- sound/soc/amd/yc/acp6x-mach.c | 21 + sound/soc/amd/yc/acp6x-pdm-dma.c | 5 +- sound/soc/amd/yc/acp6x.h | 3 + sound/soc/amd/yc/pci-acp6x.c | 8 +- sound/soc/apple/mca.c | 5 +- sound/soc/atmel/atmel-classd.c | 5 +- sound/soc/atmel/atmel-i2s.c | 6 +- sound/soc/atmel/atmel-pdmic.c | 5 +- sound/soc/atmel/atmel_wm8904.c | 6 +- sound/soc/atmel/mchp-i2s-mcc.c | 6 +- sound/soc/atmel/mchp-pdmc.c | 25 +- sound/soc/atmel/mchp-spdifrx.c | 6 +- sound/soc/atmel/mchp-spdiftx.c | 51 +- sound/soc/atmel/mikroe-proto.c | 6 +- sound/soc/atmel/sam9g20_wm8731.c | 6 +- sound/soc/atmel/sam9x5_wm8731.c | 6 +- sound/soc/atmel/tse850-pcm5142.c | 6 +- sound/soc/au1x/ac97c.c | 6 +- sound/soc/au1x/i2sc.c | 6 +- sound/soc/au1x/psc-ac97.c | 6 +- sound/soc/au1x/psc-i2s.c | 6 +- sound/soc/bcm/bcm63xx-i2s-whistler.c | 5 +- sound/soc/bcm/cygnus-ssp.c | 6 +- sound/soc/cirrus/Kconfig | 6 +- sound/soc/cirrus/edb93xx.c | 6 +- sound/soc/cirrus/ep93xx-i2s.c | 25 +- sound/soc/codecs/Kconfig | 62 + sound/soc/codecs/Makefile | 14 + sound/soc/codecs/adau1977-spi.c | 2 +- sound/soc/codecs/cs35l41-lib.c | 73 +- sound/soc/codecs/cs35l41.c | 144 +- sound/soc/codecs/cs35l41.h | 1 + sound/soc/codecs/cs35l45-i2c.c | 3 + sound/soc/codecs/cs35l45-spi.c | 5 + sound/soc/codecs/cs35l45-tables.c | 135 +- sound/soc/codecs/cs35l45.c | 630 +++++++- sound/soc/codecs/cs35l45.h | 267 +++- sound/soc/codecs/cs35l56-i2c.c | 82 + sound/soc/codecs/cs35l56-sdw.c | 566 +++++++ sound/soc/codecs/cs35l56-shared.c | 362 +++++ sound/soc/codecs/cs35l56-spi.c | 79 + sound/soc/codecs/cs35l56.c | 1601 ++++++++++++++++++++ sound/soc/codecs/cs35l56.h | 81 + sound/soc/codecs/cs4271-i2c.c | 1 - sound/soc/codecs/cs4271-spi.c | 1 - sound/soc/codecs/cs4271.c | 4 +- sound/soc/codecs/cs42l42-sdw.c | 3 - sound/soc/codecs/cs47l15.c | 6 +- sound/soc/codecs/cs47l24.c | 6 +- sound/soc/codecs/cs47l35.c | 6 +- sound/soc/codecs/cs47l85.c | 6 +- sound/soc/codecs/cs47l90.c | 6 +- sound/soc/codecs/cs47l92.c | 6 +- sound/soc/codecs/da7218.c | 10 +- sound/soc/codecs/da7219-aad.c | 60 +- sound/soc/codecs/da7219-aad.h | 5 +- sound/soc/codecs/es8316.c | 33 +- sound/soc/codecs/inno_rk3036.c | 6 +- sound/soc/codecs/lpass-macro-common.c | 2 +- sound/soc/codecs/lpass-macro-common.h | 3 + sound/soc/codecs/lpass-rx-macro.c | 42 +- sound/soc/codecs/lpass-tx-macro.c | 41 +- sound/soc/codecs/lpass-va-macro.c | 6 +- sound/soc/codecs/lpass-wsa-macro.c | 43 +- sound/soc/codecs/max98363.c | 464 ++++++ sound/soc/codecs/max98363.h | 36 + sound/soc/codecs/max98373-sdw.c | 34 +- sound/soc/codecs/max9867.c | 19 +- sound/soc/codecs/msm8916-wcd-analog.c | 6 +- sound/soc/codecs/msm8916-wcd-digital.c | 6 +- sound/soc/codecs/mt6358.c | 2 +- sound/soc/codecs/mt6359.c | 2 +- sound/soc/codecs/nau8821.c | 96 ++ sound/soc/codecs/nau8821.h | 23 + sound/soc/codecs/nau8825.c | 8 +- sound/soc/codecs/nau8825.h | 1 + sound/soc/codecs/pcm179x-spi.c | 2 +- sound/soc/codecs/rk817_codec.c | 6 +- sound/soc/codecs/rt1019.c | 2 +- sound/soc/codecs/rt1308-sdw.c | 30 +- sound/soc/codecs/rt1308-sdw.h | 4 - sound/soc/codecs/rt1316-sdw.c | 30 +- sound/soc/codecs/rt1316-sdw.h | 4 - sound/soc/codecs/rt1318-sdw.c | 30 +- sound/soc/codecs/rt1318-sdw.h | 4 - sound/soc/codecs/rt5682-sdw.c | 34 +- sound/soc/codecs/rt700.c | 30 +- sound/soc/codecs/rt700.h | 4 - sound/soc/codecs/rt711-sdca.c | 30 +- sound/soc/codecs/rt711-sdca.h | 4 - sound/soc/codecs/rt711.c | 30 +- sound/soc/codecs/rt711.h | 4 - sound/soc/codecs/rt712-sdca-dmic.c | 983 ++++++++++++ sound/soc/codecs/rt712-sdca-dmic.h | 108 ++ sound/soc/codecs/rt712-sdca.c | 30 +- sound/soc/codecs/rt712-sdca.h | 4 - sound/soc/codecs/rt715-sdca.c | 30 +- sound/soc/codecs/rt715-sdca.h | 4 - sound/soc/codecs/rt715.c | 30 +- sound/soc/codecs/rt715.h | 4 - sound/soc/codecs/sdw-mockup.c | 34 +- sound/soc/codecs/sma1303.c | 2 +- sound/soc/codecs/src4xxx-i2c.c | 2 +- sound/soc/codecs/ssm2602.c | 15 +- sound/soc/codecs/sta32x.c | 39 +- sound/soc/codecs/sta350.c | 63 +- sound/soc/codecs/tas5086.c | 2 +- sound/soc/codecs/tas571x.c | 59 + sound/soc/codecs/tas5720.c | 3 +- sound/soc/codecs/wcd9335.c | 27 +- sound/soc/codecs/wcd934x.c | 25 +- sound/soc/codecs/wcd938x.c | 33 +- sound/soc/codecs/wm5102.c | 6 +- sound/soc/codecs/wm5110.c | 6 +- sound/soc/codecs/wm8903.c | 1 - sound/soc/codecs/wm8994.c | 6 +- sound/soc/codecs/wm8997.c | 6 +- sound/soc/codecs/wm8998.c | 6 +- sound/soc/codecs/wm_adsp.c | 63 +- sound/soc/codecs/wm_adsp.h | 3 + sound/soc/codecs/zl38060.c | 2 +- sound/soc/dwc/dwc-i2s.c | 5 +- sound/soc/fsl/Kconfig | 9 + sound/soc/fsl/Makefile | 2 + sound/soc/fsl/eukrea-tlv320.c | 6 +- sound/soc/fsl/fsl-asoc-card.c | 9 +- sound/soc/fsl/fsl_asrc.c | 6 +- sound/soc/fsl/fsl_aud2htx.c | 6 +- sound/soc/fsl/fsl_audmix.c | 6 +- sound/soc/fsl/fsl_dma.c | 6 +- sound/soc/fsl/fsl_easrc.c | 6 +- sound/soc/fsl/fsl_esai.c | 6 +- sound/soc/fsl/fsl_mqs.c | 20 +- sound/soc/fsl/fsl_qmc_audio.c | 735 +++++++++ sound/soc/fsl/fsl_rpmsg.c | 6 +- sound/soc/fsl/fsl_sai.c | 18 +- sound/soc/fsl/fsl_spdif.c | 6 +- sound/soc/fsl/fsl_ssi.c | 8 +- sound/soc/fsl/fsl_xcvr.c | 5 +- sound/soc/fsl/imx-audmix.c | 22 +- sound/soc/fsl/imx-audmux.c | 6 +- sound/soc/fsl/imx-card.c | 2 +- sound/soc/fsl/imx-es8328.c | 11 +- sound/soc/fsl/imx-pcm-rpmsg.c | 6 +- sound/soc/fsl/imx-sgtl5000.c | 6 +- sound/soc/fsl/imx-spdif.c | 11 +- sound/soc/fsl/mpc5200_psc_ac97.c | 5 +- sound/soc/fsl/mpc5200_psc_i2s.c | 5 +- sound/soc/fsl/mpc8610_hpcd.c | 6 +- sound/soc/fsl/p1022_ds.c | 6 +- sound/soc/fsl/p1022_rdk.c | 6 +- sound/soc/fsl/pcm030-audio-fabric.c | 6 +- sound/soc/generic/audio-graph-card.c | 15 +- .../soc/generic/audio-graph-card2-custom-sample.c | 3 + sound/soc/generic/audio-graph-card2.c | 23 +- sound/soc/generic/simple-card-utils.c | 35 +- sound/soc/generic/simple-card.c | 23 +- sound/soc/generic/test-component.c | 6 +- sound/soc/img/img-i2s-in.c | 6 +- sound/soc/img/img-i2s-out.c | 6 +- sound/soc/img/img-parallel-out.c | 6 +- sound/soc/img/img-spdif-in.c | 6 +- sound/soc/img/img-spdif-out.c | 6 +- sound/soc/img/pistachio-internal-dac.c | 6 +- sound/soc/intel/atom/sst-mfld-platform-pcm.c | 5 +- sound/soc/intel/atom/sst/sst_acpi.c | 5 +- sound/soc/intel/avs/boards/hdaudio.c | 10 +- sound/soc/intel/avs/path.c | 2 +- sound/soc/intel/boards/bytcht_es8316.c | 5 +- sound/soc/intel/boards/bytcr_rt5640.c | 5 +- sound/soc/intel/boards/bytcr_rt5651.c | 5 +- sound/soc/intel/boards/bytcr_wm5102.c | 5 +- sound/soc/intel/boards/cht_bsw_max98090_ti.c | 6 +- sound/soc/intel/boards/sof_cirrus_common.c | 7 +- sound/soc/intel/boards/sof_es8336.c | 6 +- sound/soc/intel/boards/sof_pcm512x.c | 6 +- sound/soc/intel/boards/sof_rt5682.c | 28 +- sound/soc/intel/boards/sof_sdw.c | 187 ++- sound/soc/intel/boards/sof_sdw_common.h | 3 - sound/soc/intel/boards/sof_sdw_max98373.c | 22 +- sound/soc/intel/boards/sof_wm8804.c | 5 +- sound/soc/intel/catpt/device.c | 6 +- sound/soc/intel/common/soc-acpi-intel-rpl-match.c | 34 +- sound/soc/intel/skylake/skl-ssp-clk.c | 6 +- sound/soc/kirkwood/kirkwood-i2s.c | 6 +- sound/soc/mediatek/common/mtk-btcvsd.c | 5 +- sound/soc/mediatek/common/mtk-soundcard-driver.c | 12 +- sound/soc/mediatek/mt2701/mt2701-afe-pcm.c | 6 +- sound/soc/mediatek/mt6797/mt6797-afe-pcm.c | 6 +- sound/soc/mediatek/mt8173/mt8173-afe-pcm.c | 5 +- sound/soc/mediatek/mt8183/mt8183-afe-pcm.c | 6 +- sound/soc/mediatek/mt8186/mt8186-afe-gpio.c | 28 +- sound/soc/mediatek/mt8186/mt8186-dai-adda.c | 4 +- .../mt8186/mt8186-mt6366-da7219-max98357.c | 2 +- .../mediatek/mt8186/mt8186-mt6366-rt1019-rt5682s.c | 6 +- sound/soc/mediatek/mt8188/mt8188-afe-pcm.c | 6 +- sound/soc/mediatek/mt8192/mt8192-afe-clk.c | 4 - sound/soc/mediatek/mt8192/mt8192-afe-pcm.c | 11 +- sound/soc/mediatek/mt8192/mt8192-dai-tdm.c | 28 +- .../mediatek/mt8192/mt8192-mt6359-rt1015-rt5682.c | 12 +- sound/soc/mediatek/mt8195/mt8195-afe-pcm.c | 5 +- sound/soc/mediatek/mt8195/mt8195-dai-adda.c | 17 +- sound/soc/mediatek/mt8195/mt8195-dai-etdm.c | 177 ++- sound/soc/mediatek/mt8195/mt8195-dai-pcm.c | 26 +- sound/soc/mediatek/mt8195/mt8195-mt6359.c | 2 +- sound/soc/meson/aiu.c | 6 +- sound/soc/meson/axg-card.c | 3 +- sound/soc/meson/axg-tdm-interface.c | 13 +- sound/soc/meson/gx-card.c | 3 +- sound/soc/meson/meson-codec-glue.c | 5 +- sound/soc/mxs/mxs-sgtl5000.c | 8 +- sound/soc/pxa/mmp-sspa.c | 7 +- sound/soc/pxa/pxa2xx-ac97.c | 5 +- sound/soc/qcom/common.c | 17 +- sound/soc/qcom/qdsp6/q6apm-lpass-dais.c | 3 + sound/soc/qcom/qdsp6/q6apm.c | 2 +- sound/soc/qcom/qdsp6/q6routing.c | 6 +- sound/soc/qcom/sdw.c | 7 +- sound/soc/rockchip/rockchip_i2s.c | 7 +- sound/soc/rockchip/rockchip_pdm.c | 6 +- sound/soc/rockchip/rockchip_rt5645.c | 6 +- sound/soc/rockchip/rockchip_spdif.c | 6 +- sound/soc/samsung/aries_wm8994.c | 6 +- sound/soc/samsung/arndale.c | 5 +- sound/soc/samsung/bells.c | 21 +- sound/soc/samsung/i2s.c | 10 +- sound/soc/samsung/littlemill.c | 3 +- sound/soc/samsung/lowland.c | 3 +- sound/soc/samsung/odroid.c | 6 +- sound/soc/samsung/pcm.c | 6 +- sound/soc/samsung/snow.c | 6 +- sound/soc/samsung/spdif.c | 6 +- sound/soc/samsung/speyside.c | 3 +- sound/soc/sh/fsi.c | 8 +- sound/soc/sh/hac.c | 5 +- sound/soc/sh/rcar/core.c | 6 +- sound/soc/sh/rcar/ssi.c | 4 +- sound/soc/sh/rz-ssi.c | 69 +- sound/soc/sh/siu_dai.c | 5 +- sound/soc/soc-component.c | 12 +- sound/soc/soc-compress.c | 70 +- sound/soc/soc-core.c | 52 +- sound/soc/soc-dai.c | 3 + sound/soc/soc-dapm.c | 324 ++-- sound/soc/soc-jack.c | 1 + sound/soc/soc-pcm.c | 37 +- sound/soc/soc-topology.c | 10 +- sound/soc/sof/amd/acp-common.c | 17 +- sound/soc/sof/amd/acp-pcm.c | 34 + sound/soc/sof/amd/acp.c | 45 +- sound/soc/sof/amd/acp.h | 7 +- sound/soc/sof/amd/pci-rmb.c | 91 +- sound/soc/sof/amd/pci-rn.c | 91 +- sound/soc/sof/amd/rembrandt.c | 4 - sound/soc/sof/amd/renoir.c | 3 - sound/soc/sof/compress.c | 8 +- sound/soc/sof/core.c | 31 +- sound/soc/sof/debug.c | 1 + sound/soc/sof/intel/Kconfig | 7 + sound/soc/sof/intel/Makefile | 5 +- sound/soc/sof/intel/apl.c | 4 + sound/soc/sof/intel/cnl.c | 4 + sound/soc/sof/intel/hda-common-ops.c | 1 - sound/soc/sof/intel/hda-ctrl.c | 9 +- sound/soc/sof/intel/hda-dai-ops.c | 390 +++++ sound/soc/sof/intel/hda-dai.c | 698 +++------ sound/soc/sof/intel/hda-dsp.c | 101 +- sound/soc/sof/intel/hda-ipc.c | 3 + sound/soc/sof/intel/hda-loader.c | 9 +- sound/soc/sof/intel/hda-mlink.c | 822 +++++++++- sound/soc/sof/intel/hda-pcm.c | 24 +- sound/soc/sof/intel/hda-stream.c | 93 +- sound/soc/sof/intel/hda.c | 233 +-- sound/soc/sof/intel/hda.h | 69 +- sound/soc/sof/intel/icl.c | 4 + sound/soc/sof/intel/mtl.c | 26 +- sound/soc/sof/intel/pci-apl.c | 2 + sound/soc/sof/intel/pci-cnl.c | 3 + sound/soc/sof/intel/pci-icl.c | 2 + sound/soc/sof/intel/pci-mtl.c | 1 + sound/soc/sof/intel/pci-skl.c | 2 + sound/soc/sof/intel/pci-tgl.c | 8 + sound/soc/sof/intel/tgl.c | 4 + sound/soc/sof/ipc3-control.c | 90 +- sound/soc/sof/ipc3-dtrace.c | 12 +- sound/soc/sof/ipc3-pcm.c | 7 +- sound/soc/sof/ipc3-topology.c | 33 +- sound/soc/sof/ipc3.c | 12 +- sound/soc/sof/ipc4-control.c | 257 +++- sound/soc/sof/ipc4-mtrace.c | 21 + sound/soc/sof/ipc4-pcm.c | 186 ++- sound/soc/sof/ipc4-topology.c | 1214 +++++++++++---- sound/soc/sof/ipc4-topology.h | 89 +- sound/soc/sof/loader.c | 4 +- sound/soc/sof/pcm.c | 63 +- sound/soc/sof/pm.c | 5 + sound/soc/sof/sof-audio.c | 85 +- sound/soc/sof/sof-audio.h | 49 +- sound/soc/sof/sof-client-ipc-flood-test.c | 3 +- sound/soc/sof/sof-client-probes-ipc3.c | 12 +- sound/soc/sof/sof-client-probes-ipc4.c | 4 +- sound/soc/sof/sof-client.c | 3 + sound/soc/sof/sof-client.h | 4 + sound/soc/sof/sof-priv.h | 21 + sound/soc/sof/topology.c | 302 +++- sound/soc/sprd/sprd-mcdt.c | 6 +- sound/soc/stm/stm32_adfsdm.c | 6 +- sound/soc/stm/stm32_i2s.c | 8 +- sound/soc/stm/stm32_sai_sub.c | 10 +- sound/soc/stm/stm32_spdifrx.c | 6 +- sound/soc/sunxi/sun4i-codec.c | 6 +- sound/soc/sunxi/sun4i-i2s.c | 6 +- sound/soc/sunxi/sun4i-spdif.c | 6 +- sound/soc/sunxi/sun50i-dmic.c | 6 +- sound/soc/sunxi/sun8i-codec.c | 6 +- sound/soc/tegra/Kconfig | 18 + sound/soc/tegra/tegra186_asrc.c | 6 +- sound/soc/tegra/tegra186_dspk.c | 6 +- sound/soc/tegra/tegra20_ac97.c | 9 +- sound/soc/tegra/tegra20_i2s.c | 6 +- sound/soc/tegra/tegra210_admaif.c | 6 +- sound/soc/tegra/tegra210_adx.c | 6 +- sound/soc/tegra/tegra210_ahub.c | 6 +- sound/soc/tegra/tegra210_amx.c | 6 +- sound/soc/tegra/tegra210_dmic.c | 6 +- sound/soc/tegra/tegra210_i2s.c | 6 +- sound/soc/tegra/tegra210_mixer.c | 6 +- sound/soc/tegra/tegra210_mvc.c | 6 +- sound/soc/tegra/tegra210_ope.c | 6 +- sound/soc/tegra/tegra210_sfc.c | 6 +- sound/soc/tegra/tegra30_ahub.c | 6 +- sound/soc/tegra/tegra30_i2s.c | 6 +- sound/soc/tegra/tegra_asoc_machine.c | 127 +- sound/soc/ti/ams-delta.c | 5 +- sound/soc/ti/davinci-i2s.c | 6 +- sound/soc/ti/davinci-mcasp.c | 6 +- sound/soc/ti/omap-hdmi.c | 10 +- sound/soc/ti/omap-mcbsp.c | 6 +- sound/soc/uniphier/evea.c | 6 +- sound/soc/ux500/mop500.c | 6 +- sound/soc/ux500/ux500_msp_dai.c | 6 +- sound/soc/xilinx/xlnx_formatter_pcm.c | 5 +- sound/soc/xilinx/xlnx_spdif.c | 5 +- sound/soc/xtensa/xtfpga-i2s.c | 5 +- sound/sparc/cs4231.c | 6 +- sound/sparc/dbri.c | 6 +- 479 files changed, 18462 insertions(+), 4482 deletions(-) create mode 100644 Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,cpm1-scc-qmc.yaml create mode 100644 Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,cpm1-tsa.yaml delete mode 100644 Documentation/devicetree/bindings/sound/adi,adau17x1.txt create mode 100644 Documentation/devicetree/bindings/sound/adi,adau17x1.yaml create mode 100644 Documentation/devicetree/bindings/sound/adi,max98363.yaml delete mode 100644 Documentation/devicetree/bindings/sound/ak4458.txt delete mode 100644 Documentation/devicetree/bindings/sound/ak5558.txt delete mode 100644 Documentation/devicetree/bindings/sound/alc5632.txt create mode 100644 Documentation/devicetree/bindings/sound/asahi-kasei,ak4458.yaml create mode 100644 Documentation/devicetree/bindings/sound/asahi-kasei,ak5558.yaml create mode 100644 Documentation/devicetree/bindings/sound/cirrus,ep9301-i2s.yaml create mode 100644 Documentation/devicetree/bindings/sound/fsl,qmc-audio.yaml delete mode 100644 Documentation/devicetree/bindings/sound/max98371.txt delete mode 100644 Documentation/devicetree/bindings/sound/max9867.txt delete mode 100644 Documentation/devicetree/bindings/sound/maxim,max9759.txt create mode 100644 Documentation/devicetree/bindings/sound/maxim,max9759.yaml create mode 100644 Documentation/devicetree/bindings/sound/maxim,max98371.yaml create mode 100644 Documentation/devicetree/bindings/sound/maxim,max9867.yaml create mode 100644 Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max9808x.yaml create mode 100644 Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5631.yaml delete mode 100644 Documentation/devicetree/bindings/sound/qcom,wcd9335.txt create mode 100644 Documentation/devicetree/bindings/sound/qcom,wcd9335.yaml create mode 100644 Documentation/devicetree/bindings/sound/realtek,alc5632.yaml create mode 100644 Documentation/devicetree/bindings/sound/wlf,wm8510.yaml create mode 100644 Documentation/devicetree/bindings/sound/wlf,wm8523.yaml create mode 100644 Documentation/devicetree/bindings/sound/wlf,wm8524.yaml create mode 100644 Documentation/devicetree/bindings/sound/wlf,wm8580.yaml create mode 100644 Documentation/devicetree/bindings/sound/wlf,wm8711.yaml create mode 100644 Documentation/devicetree/bindings/sound/wlf,wm8728.yaml create mode 100644 Documentation/devicetree/bindings/sound/wlf,wm8737.yaml create mode 100644 Documentation/devicetree/bindings/sound/wlf,wm8753.yaml create mode 100644 Documentation/devicetree/bindings/sound/wlf,wm8960.yaml create mode 100644 Documentation/devicetree/bindings/sound/wlf,wm8994.yaml delete mode 100644 Documentation/devicetree/bindings/sound/wm8510.txt delete mode 100644 Documentation/devicetree/bindings/sound/wm8523.txt delete mode 100644 Documentation/devicetree/bindings/sound/wm8524.txt delete mode 100644 Documentation/devicetree/bindings/sound/wm8580.txt delete mode 100644 Documentation/devicetree/bindings/sound/wm8711.txt delete mode 100644 Documentation/devicetree/bindings/sound/wm8728.txt delete mode 100644 Documentation/devicetree/bindings/sound/wm8737.txt delete mode 100644 Documentation/devicetree/bindings/sound/wm8753.txt delete mode 100644 Documentation/devicetree/bindings/sound/wm8960.txt delete mode 100644 Documentation/devicetree/bindings/sound/wm8994.txt create mode 100644 Documentation/sound/hd-audio/intel-multi-link.rst create mode 100644 drivers/soc/fsl/qe/qmc.c create mode 100644 drivers/soc/fsl/qe/tsa.c create mode 100644 drivers/soc/fsl/qe/tsa.h create mode 100644 include/dt-bindings/soc/cpm1-fsl,tsa.h create mode 100644 include/soc/fsl/qe/qmc.h create mode 100644 include/sound/cs35l56.h create mode 100644 include/sound/hda-mlink.h create mode 100644 sound/soc/codecs/cs35l56-i2c.c create mode 100644 sound/soc/codecs/cs35l56-sdw.c create mode 100644 sound/soc/codecs/cs35l56-shared.c create mode 100644 sound/soc/codecs/cs35l56-spi.c create mode 100644 sound/soc/codecs/cs35l56.c create mode 100644 sound/soc/codecs/cs35l56.h create mode 100644 sound/soc/codecs/max98363.c create mode 100644 sound/soc/codecs/max98363.h create mode 100644 sound/soc/codecs/rt712-sdca-dmic.c create mode 100644 sound/soc/codecs/rt712-sdca-dmic.h create mode 100644 sound/soc/fsl/fsl_qmc_audio.c create mode 100644 sound/soc/sof/intel/hda-dai-ops.c

2 1

[PATCH v2 1/2] ALSA: emu10k1: use high-level I/O functions also during init
by Oswald Buddenhagen 24 Apr '23

24 Apr '23

... and also use more pre-defined constants on the way (some of which required adjustment). This makes the code much shorter and more legible. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- include/sound/emu10k1.h | 9 +++++---- sound/pci/emu10k1/emu10k1_main.c | 20 ++++++-------------- 2 files changed, 11 insertions(+), 18 deletions(-) diff --git a/include/sound/emu10k1.h b/include/sound/emu10k1.h index 5958cae819fd..05a09826eef0 100644 --- a/include/sound/emu10k1.h +++ b/include/sound/emu10k1.h @@ -852,10 +852,11 @@ #define A_SPDIF_MUTED 0x000000c0 #define A_I2S_CAPTURE_RATE_MASK 0x00000e00 /* This sets the capture PCM rate, but it is */ -#define A_I2S_CAPTURE_48000 0x00000000 /* unclear if this sets the ADC rate as well. */ -#define A_I2S_CAPTURE_192000 0x00000200 -#define A_I2S_CAPTURE_96000 0x00000400 -#define A_I2S_CAPTURE_44100 0x00000800 +#define A_I2S_CAPTURE_RATE 0x03090076 /* unclear if this sets the ADC rate as well. */ +#define A_I2S_CAPTURE_48000 0x0 +#define A_I2S_CAPTURE_192000 0x1 +#define A_I2S_CAPTURE_96000 0x2 +#define A_I2S_CAPTURE_44100 0x4 #define A_EHC_SRC48_MASK 0x0000e000 /* This sets the playback PCM rate on the P16V */ #define A_EHC_SRC48_BYPASS 0x00000000 diff --git a/sound/pci/emu10k1/emu10k1_main.c b/sound/pci/emu10k1/emu10k1_main.c index e53eb7fd0883..3aca01c70ccb 100644 --- a/sound/pci/emu10k1/emu10k1_main.c +++ b/sound/pci/emu10k1/emu10k1_main.c @@ -186,10 +186,7 @@ static int snd_emu10k1_init(struct snd_emu10k1 *emu, int enable_ir) if (emu->card_capabilities->ca0151_chip) { /* audigy2 */ /* Hacks for Alice3 to work independent of haP16V driver */ /* Setup SRCMulti_I2S SamplingRate */ - tmp = snd_emu10k1_ptr_read(emu, A_SPDIF_SAMPLERATE, 0); - tmp &= 0xfffff1ff; - tmp |= (0x2<<9); - snd_emu10k1_ptr_write(emu, A_SPDIF_SAMPLERATE, 0, tmp); + snd_emu10k1_ptr_write(emu, A_I2S_CAPTURE_RATE, 0, A_I2S_CAPTURE_96000); /* Setup SRCSel (Enable Spdif,I2S SRCMulti) */ snd_emu10k1_ptr20_write(emu, SRCSel, 0, 0x14); @@ -206,25 +203,20 @@ static int snd_emu10k1_init(struct snd_emu10k1 *emu, int enable_ir) /* Hacks for Alice3 to work independent of haP16V driver */ dev_info(emu->card->dev, "Audigy2 value: Special config.\n"); /* Setup SRCMulti_I2S SamplingRate */ - tmp = snd_emu10k1_ptr_read(emu, A_SPDIF_SAMPLERATE, 0); - tmp &= 0xfffff1ff; - tmp |= (0x2<<9); - snd_emu10k1_ptr_write(emu, A_SPDIF_SAMPLERATE, 0, tmp); + snd_emu10k1_ptr_write(emu, A_I2S_CAPTURE_RATE, 0, A_I2S_CAPTURE_96000); /* Setup SRCSel (Enable Spdif,I2S SRCMulti) */ - outl(0x600000, emu->port + 0x20); - outl(0x14, emu->port + 0x24); + snd_emu10k1_ptr20_write(emu, P17V_SRCSel, 0, 0x14); /* Setup SRCMulti Input Audio Enable */ - outl(0x7b0000, emu->port + 0x20); - outl(0xFF000000, emu->port + 0x24); + snd_emu10k1_ptr20_write(emu, P17V_MIXER_I2S_ENABLE, 0, 0xFF000000); /* Setup SPDIF Out Audio Enable */ /* The Audigy 2 Value has a separate SPDIF out, * so no need for a mixer switch */ - outl(0x7a0000, emu->port + 0x20); - outl(0xFF000000, emu->port + 0x24); + snd_emu10k1_ptr20_write(emu, P17V_MIXER_SPDIF_ENABLE, 0, 0xFF000000); + tmp = inw(emu->port + A_IOCFG) & ~0x8; /* Clear bit 3 */ outw(tmp, emu->port + A_IOCFG); } -- 2.40.0.152.g15d061e6df

2 2

[PATCH v2 0/7] ASoC: mediatek: mt8188: revise AFE driver
by Trevor Wu 24 Apr '23

24 Apr '23

The series of patches consists of three major changes. First, remove redundant supply for ADDA DAI dirver. Second, revise ETDM control including APLL dynamic switch via DAPM, so APLL can be enabled when it is really required. Finally, AFE probe function is updated. Bus protection change was dropped at the previous patch because the dependent change was not accepted. Changes since v1: - replace unnecessary dev_info with dev_dbg - fix dt-binging ABI breaking behavior Trevor Wu (7): ASoC: mediatek: mt8188: remove supply AUDIO_HIRES ASoC: mediatek: mt8188: complete set_tdm_slot function ASoC: mediatek: mt8188: revise ETDM control flow ASoC: mediatek: mt8188: refine APLL control ASoC: mediatek: mt8188: combine afe component registration ASoC: mediatek: mt8188: add bus protection ASoC: dt-bindings: mediatek,mt8188-afe: add audio properties .../bindings/sound/mediatek,mt8188-afe.yaml | 16 +- sound/soc/mediatek/mt8188/mt8188-afe-clk.c | 138 ++- sound/soc/mediatek/mt8188/mt8188-afe-clk.h | 11 + sound/soc/mediatek/mt8188/mt8188-afe-pcm.c | 113 ++- sound/soc/mediatek/mt8188/mt8188-dai-adda.c | 37 - sound/soc/mediatek/mt8188/mt8188-dai-etdm.c | 922 ++++++++++-------- sound/soc/mediatek/mt8188/mt8188-reg.h | 2 + 7 files changed, 755 insertions(+), 484 deletions(-) -- 2.18.0

3 9

[PATCH v2 00/13] ASoC: add and use asoc_dummy_dlc
by Kuninori Morimoto 24 Apr '23

24 Apr '23

Hi Mark These are v2 patch-set of asoc_dummy_dlc. Many ASoC drivers are using dummy DAI. I have 2 concern about it. 1st one is there is no guarantee that local strings ("snd-soc-dummy-dai", "snd-soc-dummy") are kept until the card was binded if it was added at subfunction. 2nd one is we can use common snd_soc_dai_link_component for it. This patch-set adds common asoc_dummy_dlc, and use it. v1 -> v2 - Separate intel patch into 3 - Topology codec doesn't use asoc_dummy_dlc Link: https://lore.kernel.org/r/874jpe3uqh.wl-kuninori.morimoto.gx@renesas.com Kuninori Morimoto (13): ASoC: soc-utils.c: add asoc_dummy_dlc ASoC: ti: use asoc_dummy_dlc ASoC: sof: use asoc_dummy_dlc ASoC: amd: use asoc_dummy_dlc ASoC: fsl: use asoc_dummy_dlc ASoC: qcom: use asoc_dummy_dlc ASoC: atmel: use asoc_dummy_dlc ASoC: meson: use asoc_dummy_dlc ASoC: intel: avs: use asoc_dummy_dlc ASoC: intel: sof: use asoc_dummy_dlc ASoC: intel: skylake: use asoc_dummy_dlc ASoC: simple_card_utils.c: use asoc_dummy_dlc ASoC: soc-topology.c: add comment for Platform/Codec include/sound/simple_card_utils.h | 1 - include/sound/soc.h | 1 + sound/soc/amd/acp/acp-mach-common.c | 43 ++++++++------------ sound/soc/atmel/atmel-classd.c | 8 ++-- sound/soc/atmel/atmel-pdmic.c | 8 ++-- sound/soc/fsl/imx-audmix.c | 14 +++---- sound/soc/fsl/imx-card.c | 11 +---- sound/soc/fsl/imx-rpmsg.c | 3 +- sound/soc/fsl/imx-spdif.c | 8 ++-- sound/soc/generic/simple-card-utils.c | 9 +--- sound/soc/intel/avs/boards/i2s_test.c | 6 +-- sound/soc/intel/boards/ehl_rt5660.c | 8 +--- sound/soc/intel/boards/skl_hda_dsp_generic.c | 8 +--- sound/soc/intel/boards/sof_cs42l42.c | 11 +---- sound/soc/intel/boards/sof_es8336.c | 11 +---- sound/soc/intel/boards/sof_nau8825.c | 11 +---- sound/soc/intel/boards/sof_pcm512x.c | 3 +- sound/soc/intel/boards/sof_rt5682.c | 14 ++----- sound/soc/intel/boards/sof_sdw.c | 13 +----- sound/soc/intel/boards/sof_ssp_amp.c | 18 +++----- sound/soc/meson/axg-card.c | 8 ++-- sound/soc/meson/meson-card-utils.c | 10 +---- sound/soc/qcom/common.c | 11 +---- sound/soc/soc-topology.c | 22 +++++----- sound/soc/soc-utils.c | 7 ++++ sound/soc/sof/nocodec.c | 8 ++-- sound/soc/ti/omap-hdmi.c | 8 ++-- 27 files changed, 89 insertions(+), 194 deletions(-) -- 2.25.1

1 13

[PATCH 1/2] ALSA: emu10k1: use high-level I/O functions also during init
by Oswald Buddenhagen 23 Apr '23

23 Apr '23

... and also use more pre-defined constants on the way (some of which required adjustment). Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- This patch series needs to be applied on top of the patch titled "ALSA: emu10k1: use more existing defines instead of open-coded numbers". --- include/sound/emu10k1.h | 9 +++++---- sound/pci/emu10k1/emu10k1_main.c | 20 ++++++-------------- 2 files changed, 11 insertions(+), 18 deletions(-) diff --git a/include/sound/emu10k1.h b/include/sound/emu10k1.h index 5958cae819fd..05a09826eef0 100644 --- a/include/sound/emu10k1.h +++ b/include/sound/emu10k1.h @@ -852,10 +852,11 @@ #define A_SPDIF_MUTED 0x000000c0 #define A_I2S_CAPTURE_RATE_MASK 0x00000e00 /* This sets the capture PCM rate, but it is */ -#define A_I2S_CAPTURE_48000 0x00000000 /* unclear if this sets the ADC rate as well. */ -#define A_I2S_CAPTURE_192000 0x00000200 -#define A_I2S_CAPTURE_96000 0x00000400 -#define A_I2S_CAPTURE_44100 0x00000800 +#define A_I2S_CAPTURE_RATE 0x03090076 /* unclear if this sets the ADC rate as well. */ +#define A_I2S_CAPTURE_48000 0x0 +#define A_I2S_CAPTURE_192000 0x1 +#define A_I2S_CAPTURE_96000 0x2 +#define A_I2S_CAPTURE_44100 0x4 #define A_EHC_SRC48_MASK 0x0000e000 /* This sets the playback PCM rate on the P16V */ #define A_EHC_SRC48_BYPASS 0x00000000 diff --git a/sound/pci/emu10k1/emu10k1_main.c b/sound/pci/emu10k1/emu10k1_main.c index e53eb7fd0883..3aca01c70ccb 100644 --- a/sound/pci/emu10k1/emu10k1_main.c +++ b/sound/pci/emu10k1/emu10k1_main.c @@ -186,10 +186,7 @@ static int snd_emu10k1_init(struct snd_emu10k1 *emu, int enable_ir) if (emu->card_capabilities->ca0151_chip) { /* audigy2 */ /* Hacks for Alice3 to work independent of haP16V driver */ /* Setup SRCMulti_I2S SamplingRate */ - tmp = snd_emu10k1_ptr_read(emu, A_SPDIF_SAMPLERATE, 0); - tmp &= 0xfffff1ff; - tmp |= (0x2<<9); - snd_emu10k1_ptr_write(emu, A_SPDIF_SAMPLERATE, 0, tmp); + snd_emu10k1_ptr_write(emu, A_I2S_CAPTURE_RATE, 0, A_I2S_CAPTURE_96000); /* Setup SRCSel (Enable Spdif,I2S SRCMulti) */ snd_emu10k1_ptr20_write(emu, SRCSel, 0, 0x14); @@ -206,25 +203,20 @@ static int snd_emu10k1_init(struct snd_emu10k1 *emu, int enable_ir) /* Hacks for Alice3 to work independent of haP16V driver */ dev_info(emu->card->dev, "Audigy2 value: Special config.\n"); /* Setup SRCMulti_I2S SamplingRate */ - tmp = snd_emu10k1_ptr_read(emu, A_SPDIF_SAMPLERATE, 0); - tmp &= 0xfffff1ff; - tmp |= (0x2<<9); - snd_emu10k1_ptr_write(emu, A_SPDIF_SAMPLERATE, 0, tmp); + snd_emu10k1_ptr_write(emu, A_I2S_CAPTURE_RATE, 0, A_I2S_CAPTURE_96000); /* Setup SRCSel (Enable Spdif,I2S SRCMulti) */ - outl(0x600000, emu->port + 0x20); - outl(0x14, emu->port + 0x24); + snd_emu10k1_ptr20_write(emu, P17V_SRCSel, 0, 0x14); /* Setup SRCMulti Input Audio Enable */ - outl(0x7b0000, emu->port + 0x20); - outl(0xFF000000, emu->port + 0x24); + snd_emu10k1_ptr20_write(emu, P17V_MIXER_I2S_ENABLE, 0, 0xFF000000); /* Setup SPDIF Out Audio Enable */ /* The Audigy 2 Value has a separate SPDIF out, * so no need for a mixer switch */ - outl(0x7a0000, emu->port + 0x20); - outl(0xFF000000, emu->port + 0x24); + snd_emu10k1_ptr20_write(emu, P17V_MIXER_SPDIF_ENABLE, 0, 0xFF000000); + tmp = inw(emu->port + A_IOCFG) & ~0x8; /* Clear bit 3 */ outw(tmp, emu->port + A_IOCFG); } -- 2.40.0.152.g15d061e6df

2 5

[PATCH] ASoC: dt-bindings: More dropping unneeded quotes
by Rob Herring 23 Apr '23

23 Apr '23

Another batch of dropping unneeded quotes on $id and $schema which were missed in the last round. Once all these are fixed, checking for this can be enabled in yamllint. Signed-off-by: Rob Herring <robh(a)kernel.org> --- .../devicetree/bindings/sound/nvidia,tegra-audio-common.yaml | 4 ++-- Documentation/devicetree/bindings/sound/qcom,q6apm-dai.yaml | 4 ++-- .../devicetree/bindings/sound/qcom,q6dsp-lpass-clocks.yaml | 4 ++-- .../devicetree/bindings/sound/qcom,q6dsp-lpass-ports.yaml | 4 ++-- Documentation/devicetree/bindings/sound/tas2562.yaml | 4 ++-- Documentation/devicetree/bindings/sound/tas2770.yaml | 4 ++-- Documentation/devicetree/bindings/sound/tas27xx.yaml | 4 ++-- Documentation/devicetree/bindings/sound/wlf,wm8903.yaml | 4 ++-- 8 files changed, 16 insertions(+), 16 deletions(-) diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-common.yaml b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-common.yaml index 7c1e9895ce85..2588589ad62d 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-common.yaml +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-common.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/sound/nvidia,tegra-audio-common.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/sound/nvidia,tegra-audio-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Common properties for NVIDIA Tegra audio complexes diff --git a/Documentation/devicetree/bindings/sound/qcom,q6apm-dai.yaml b/Documentation/devicetree/bindings/sound/qcom,q6apm-dai.yaml index cdbb4096fa44..9e5b30d9c6e6 100644 --- a/Documentation/devicetree/bindings/sound/qcom,q6apm-dai.yaml +++ b/Documentation/devicetree/bindings/sound/qcom,q6apm-dai.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/sound/qcom,q6apm-dai.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/sound/qcom,q6apm-dai.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Qualcomm Audio Process Manager Digital Audio Interfaces diff --git a/Documentation/devicetree/bindings/sound/qcom,q6dsp-lpass-clocks.yaml b/Documentation/devicetree/bindings/sound/qcom,q6dsp-lpass-clocks.yaml index 1168410f6fbd..3552c44137ed 100644 --- a/Documentation/devicetree/bindings/sound/qcom,q6dsp-lpass-clocks.yaml +++ b/Documentation/devicetree/bindings/sound/qcom,q6dsp-lpass-clocks.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/sound/qcom,q6dsp-lpass-clocks.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/sound/qcom,q6dsp-lpass-clocks.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Qualcomm DSP LPASS Clock Controller diff --git a/Documentation/devicetree/bindings/sound/qcom,q6dsp-lpass-ports.yaml b/Documentation/devicetree/bindings/sound/qcom,q6dsp-lpass-ports.yaml index 044e77718a1b..08c618e7e428 100644 --- a/Documentation/devicetree/bindings/sound/qcom,q6dsp-lpass-ports.yaml +++ b/Documentation/devicetree/bindings/sound/qcom,q6dsp-lpass-ports.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/sound/qcom,q6dsp-lpass-ports.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/sound/qcom,q6dsp-lpass-ports.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Qualcomm DSP LPASS(Low Power Audio SubSystem) Audio Ports diff --git a/Documentation/devicetree/bindings/sound/tas2562.yaml b/Documentation/devicetree/bindings/sound/tas2562.yaml index a5bb561bfcfb..41489a3ac79f 100644 --- a/Documentation/devicetree/bindings/sound/tas2562.yaml +++ b/Documentation/devicetree/bindings/sound/tas2562.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2019 Texas Instruments Incorporated %YAML 1.2 --- -$id: "http://devicetree.org/schemas/sound/tas2562.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/sound/tas2562.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Texas Instruments TAS2562 Smart PA diff --git a/Documentation/devicetree/bindings/sound/tas2770.yaml b/Documentation/devicetree/bindings/sound/tas2770.yaml index 26088adb9dc2..930bd111b072 100644 --- a/Documentation/devicetree/bindings/sound/tas2770.yaml +++ b/Documentation/devicetree/bindings/sound/tas2770.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2019-20 Texas Instruments Incorporated %YAML 1.2 --- -$id: "http://devicetree.org/schemas/sound/tas2770.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/sound/tas2770.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Texas Instruments TAS2770 Smart PA diff --git a/Documentation/devicetree/bindings/sound/tas27xx.yaml b/Documentation/devicetree/bindings/sound/tas27xx.yaml index 8cba01316855..bda26b246634 100644 --- a/Documentation/devicetree/bindings/sound/tas27xx.yaml +++ b/Documentation/devicetree/bindings/sound/tas27xx.yaml @@ -2,8 +2,8 @@ # Copyright (C) 2020-2022 Texas Instruments Incorporated %YAML 1.2 --- -$id: "http://devicetree.org/schemas/sound/tas27xx.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/sound/tas27xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Texas Instruments TAS2764/TAS2780 Smart PA diff --git a/Documentation/devicetree/bindings/sound/wlf,wm8903.yaml b/Documentation/devicetree/bindings/sound/wlf,wm8903.yaml index 7105ed5fd6c7..4cfa66f62681 100644 --- a/Documentation/devicetree/bindings/sound/wlf,wm8903.yaml +++ b/Documentation/devicetree/bindings/sound/wlf,wm8903.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/sound/wlf,wm8903.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/sound/wlf,wm8903.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: WM8903 audio codec -- 2.39.2

2 1

Re: [PATCH] ALSA: hda: Glenfly: add HD Audio PCI IDs and HDMI Codec Vendor IDs.
by Takashi Iwai 23 Apr '23

23 Apr '23

On Tue, 18 Apr 2023 10:33:12 +0200, reaperli wrote: > > From: jasontao <jasontao(a)glenfly.com> > > Add a set of HD Audio PCI IDS, and the HDMI codec vendor IDs for > Glenfly Arise. > > Signed-off-by: jasontao <jasontao(a)glenfly.com> > Signed-off-by: reaperli <reaperlioc(a)glenfly.com> The patch looks OK now, but could you submit to alsa-devel ML at the next time? About details in the patch: > @@ -1743,6 +1745,8 @@ static int default_bdl_pos_adj(struct azx *chip) > } > > switch (chip->driver_type) { > + case AZX_DRIVER_GFHDMI: > + return 128; So this looks pretty high in comparison with other chips. It means that the actual position is much behind the reported position. Due to a large FIFO? Or what reason? > @@ -1859,6 +1863,9 @@ static int azx_first_init(struct azx *chip) > } > #endif > > + if (chip->driver_type == AZX_DRIVER_GFHDMI) > + bus->polling_mode = 1; This looks odd, too. Doesn't the hardware give any interrupt back upon the CORB/RIRB response? > --- a/sound/pci/hda/patch_hdmi.c > +++ b/sound/pci/hda/patch_hdmi.c > @@ -4489,6 +4489,18 @@ static int patch_via_hdmi(struct hda_codec *codec) > return patch_simple_hdmi(codec, VIAHDMI_CVT_NID, VIAHDMI_PIN_NID); > } > > +static int patch_gf_hdmi(struct hda_codec *codec) > +{ > + int err; > + > + err = patch_generic_hdmi(codec); > + if (err) > + return err; > + > + codec->no_sticky_stream = 1; This hack is needed for what reason? thanks, Takashi

2 3

[PATCH 1/2] ALSA: emu10k1: fix SNDRV_EMU10K1_IOCTL_SINGLE_STEP
by Oswald Buddenhagen 23 Apr '23

23 Apr '23

- Use correct address limit for Audigy - Use the right constant to actually make a step on Audigy - Don't store *_DBG_STEP and the address in emu->fx8010.dbg, as otherwise unrelated operations would make steps, too This is untested. as10k1 was never ported to Audigy anyway. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- sound/pci/emu10k1/emufx.c | 24 +++++++++++++----------- 1 file changed, 13 insertions(+), 11 deletions(-) diff --git a/sound/pci/emu10k1/emufx.c b/sound/pci/emu10k1/emufx.c index 6a51aed59238..70ec2cb9efe8 100644 --- a/sound/pci/emu10k1/emufx.c +++ b/sound/pci/emu10k1/emufx.c @@ -2646,17 +2646,19 @@ static int snd_emu10k1_fx8010_ioctl(struct snd_hwdep * hw, struct file *file, un return -EPERM; if (get_user(addr, (unsigned int __user *)argp)) return -EFAULT; - if (addr > 0x1ff) - return -EINVAL; - if (emu->audigy) - snd_emu10k1_ptr_write(emu, A_DBG, 0, emu->fx8010.dbg |= A_DBG_SINGLE_STEP | addr); - else - snd_emu10k1_ptr_write(emu, DBG, 0, emu->fx8010.dbg |= EMU10K1_DBG_SINGLE_STEP | addr); - udelay(10); - if (emu->audigy) - snd_emu10k1_ptr_write(emu, A_DBG, 0, emu->fx8010.dbg |= A_DBG_SINGLE_STEP | A_DBG_STEP_ADDR | addr); - else - snd_emu10k1_ptr_write(emu, DBG, 0, emu->fx8010.dbg |= EMU10K1_DBG_SINGLE_STEP | EMU10K1_DBG_STEP | addr); + if (emu->audigy) { + if (addr > A_DBG_STEP_ADDR) + return -EINVAL; + snd_emu10k1_ptr_write(emu, A_DBG, 0, emu->fx8010.dbg |= A_DBG_SINGLE_STEP); + udelay(10); + snd_emu10k1_ptr_write(emu, A_DBG, 0, emu->fx8010.dbg | A_DBG_STEP | addr); + } else { + if (addr > EMU10K1_DBG_SINGLE_STEP_ADDR) + return -EINVAL; + snd_emu10k1_ptr_write(emu, DBG, 0, emu->fx8010.dbg |= EMU10K1_DBG_SINGLE_STEP); + udelay(10); + snd_emu10k1_ptr_write(emu, DBG, 0, emu->fx8010.dbg | EMU10K1_DBG_STEP | addr); + } return 0; case SNDRV_EMU10K1_IOCTL_DBG_READ: if (emu->audigy) -- 2.40.0.152.g15d061e6df

3 4

[PATCH] ALSA: emu10k1: fix error handling in snd_audigy_i2c_volume_put()
by Oswald Buddenhagen 23 Apr '23

23 Apr '23

Check all inputs before changing anything, and return the right error code in case of failure. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- sound/pci/emu10k1/emumixer.c | 26 +++++++++++++------------- 1 file changed, 13 insertions(+), 13 deletions(-) diff --git a/sound/pci/emu10k1/emumixer.c b/sound/pci/emu10k1/emumixer.c index 754d91050af2..2b1afbef92c7 100644 --- a/sound/pci/emu10k1/emumixer.c +++ b/sound/pci/emu10k1/emumixer.c @@ -1005,33 +1005,33 @@ static int snd_audigy_i2c_volume_put(struct snd_kcontrol *kcontrol, { struct snd_emu10k1 *emu = snd_kcontrol_chip(kcontrol); unsigned int ogain; - unsigned int ngain; + unsigned int ngain0, ngain1; unsigned int source_id; int change = 0; source_id = kcontrol->private_value; /* Limit: emu->i2c_capture_volume */ /* capture_source: uinfo->value.enumerated.items = 2 */ if (source_id >= 2) return -EINVAL; + ngain0 = ucontrol->value.integer.value[0]; + ngain1 = ucontrol->value.integer.value[1]; + if (ngain0 > 0xff) + return -EINVAL; + if (ngain1 > 0xff) + return -EINVAL; ogain = emu->i2c_capture_volume[source_id][0]; /* Left */ - ngain = ucontrol->value.integer.value[0]; - if (ngain > 0xff) - return 0; - if (ogain != ngain) { + if (ogain != ngain0) { if (emu->i2c_capture_source == source_id) - snd_emu10k1_i2c_write(emu, ADC_ATTEN_ADCL, ((ngain) & 0xff) ); - emu->i2c_capture_volume[source_id][0] = ngain; + snd_emu10k1_i2c_write(emu, ADC_ATTEN_ADCL, ngain0); + emu->i2c_capture_volume[source_id][0] = ngain0; change = 1; } ogain = emu->i2c_capture_volume[source_id][1]; /* Right */ - ngain = ucontrol->value.integer.value[1]; - if (ngain > 0xff) - return 0; - if (ogain != ngain) { + if (ogain != ngain1) { if (emu->i2c_capture_source == source_id) - snd_emu10k1_i2c_write(emu, ADC_ATTEN_ADCR, ((ngain) & 0xff)); - emu->i2c_capture_volume[source_id][1] = ngain; + snd_emu10k1_i2c_write(emu, ADC_ATTEN_ADCR, ngain1); + emu->i2c_capture_volume[source_id][1] = ngain1; change = 1; } -- 2.40.0.152.g15d061e6df

2 1

[PATCH] ALSA: emu10k1: skip Sound Blaster-specific hacks for E-MU cards
by Oswald Buddenhagen 23 Apr '23

23 Apr '23

The rev2 cards use CA0108, but the embedded P17V goes entirely unused. Also, A_IOCTL (which is really the GPIO port) is actually the FPGA control port, so messing with it is no good idea. The hacks are actually mutually exclusive, so make that explicit while we're at it. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- sound/pci/emu10k1/emu10k1_main.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/sound/pci/emu10k1/emu10k1_main.c b/sound/pci/emu10k1/emu10k1_main.c index c37df604d470..3607d2e1c905 100644 --- a/sound/pci/emu10k1/emu10k1_main.c +++ b/sound/pci/emu10k1/emu10k1_main.c @@ -181,7 +181,8 @@ static int snd_emu10k1_init(struct snd_emu10k1 *emu, int enable_ir) snd_emu10k1_ptr_write(emu, SPCS1, 0, emu->spdif_bits[1]); snd_emu10k1_ptr_write(emu, SPCS2, 0, emu->spdif_bits[2]); - if (emu->card_capabilities->ca0151_chip) { /* audigy2 */ + if (emu->card_capabilities->emu_model) { + } else if (emu->card_capabilities->ca0151_chip) { /* audigy2 */ /* Hacks for Alice3 to work independent of haP16V driver */ /* Setup SRCMulti_I2S SamplingRate */ tmp = snd_emu10k1_ptr_read(emu, A_SPDIF_SAMPLERATE, 0); @@ -199,8 +200,7 @@ static int snd_emu10k1_init(struct snd_emu10k1 *emu, int enable_ir) outl(0x0201, emu->port + HCFG2); /* Set playback routing. */ snd_emu10k1_ptr20_write(emu, CAPTURE_P16V_SOURCE, 0, 0x78e4); - } - if (emu->card_capabilities->ca0108_chip) { /* audigy2 Value */ + } else if (emu->card_capabilities->ca0108_chip) { /* audigy2 Value */ /* Hacks for Alice3 to work independent of haP16V driver */ dev_info(emu->card->dev, "Audigy2 value: Special config.\n"); /* Setup SRCMulti_I2S SamplingRate */ -- 2.40.0.152.g15d061e6df

2 1

Request to configure libhinawa and hinawa-rs repositories
by Takashi Sakamoto 23 Apr '23

23 Apr '23

Hi Jaroslav, Thanks for your administration in many repositories hosting on github.com. I'd like you to change 'About' messages for the two repositories, since I decide to host some repository in git.kernel.org. * For libhinawa repository * 'Mirror of https://git.kernel.org/pub/scm/libs/ieee1394/libhinawa.git/ for user support and continuous integration ' * For hinawa-rs repository * 'Mirror of https://git.kernel.org/pub/scm/libs/ieee1394/hinawa-rs.git/ for user support and continuous integration ' As getting my account in kernel.org, I will use git.kernel.org to host libhinawa[1] and hinawa-rs[2] repositories. But the issue tracker and continuous integration of github is still useful, so I would like to leave current repositories as is just for the purpose. [1] https://git.kernel.org/pub/scm/libs/ieee1394/libhinawa.git/ [2] https://git.kernel.org/pub/scm/libs/ieee1394/hinawa-rs.git/ Thanks in advance Takashi Sakamoto

2 2

[PATCH v2] ALSA: emu10k1: fix snd_emu1010_fpga_read() input masking for rev2 cards
by Oswald Buddenhagen 22 Apr '23

22 Apr '23

Unlike the Alice2 chips used on 1st generation E-MU cards, the Tina/Tina2 chips used on the 2nd gen cards have only six GPIN pins, which means that we need to use a smaller mask. Failure to do so would falsify the read data if the FPGA tried to raise an IRQ right at that moment. This wasn't a problem so far, as we didn't actually enable FPGA IRQs, but that's going to change soon. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- v2: - added description --- include/sound/emu10k1.h | 3 ++- sound/pci/emu10k1/io.c | 5 ++++- 2 files changed, 6 insertions(+), 2 deletions(-) diff --git a/include/sound/emu10k1.h b/include/sound/emu10k1.h index 89dbd2e93410..83130965c90a 100644 --- a/include/sound/emu10k1.h +++ b/include/sound/emu10k1.h @@ -252,7 +252,8 @@ #define MUSTAT_ORDYN 0x40 /* 0 = MUDATA can accept a command or data */ #define A_GPIO 0x18 /* GPIO on Audigy card (16bits) */ -#define A_GPINPUT_MASK 0xff00 +#define A_GPINPUT_MASK 0xff00 /* Alice/2 has 8 input pins */ +#define A3_GPINPUT_MASK 0x3f00 /* ... while Tina/2 has only 6 */ #define A_GPOUTPUT_MASK 0x00ff // The GPIO port is used for I/O config on Sound Blasters; diff --git a/sound/pci/emu10k1/io.c b/sound/pci/emu10k1/io.c index f0134689c320..42b06f2e5552 100644 --- a/sound/pci/emu10k1/io.c +++ b/sound/pci/emu10k1/io.c @@ -255,16 +255,19 @@ void snd_emu1010_fpga_write(struct snd_emu10k1 *emu, u32 reg, u32 value) void snd_emu1010_fpga_read(struct snd_emu10k1 *emu, u32 reg, u32 *value) { + // The higest input pin is used as the designated interrupt trigger, + // so it needs to be masked out. + u32 mask = emu->card_capabilities->ca0108_chip ? 0x1f : 0x7f; unsigned long flags; if (snd_BUG_ON(reg > 0x3f)) return; reg += 0x40; /* 0x40 upwards are registers. */ spin_lock_irqsave(&emu->emu_lock, flags); outw(reg, emu->port + A_GPIO); udelay(10); outw(reg | 0x80, emu->port + A_GPIO); /* High bit clocks the value into the fpga. */ udelay(10); - *value = ((inw(emu->port + A_GPIO) >> 8) & 0x7f); + *value = ((inw(emu->port + A_GPIO) >> 8) & mask); spin_unlock_irqrestore(&emu->emu_lock, flags); } -- 2.40.0.152.g15d061e6df

2 1

[PATCH v2 1/2] ALSA: emu10k1: remove unused `resume` parameter from snd_emu10k1_init()
by Oswald Buddenhagen 22 Apr '23

22 Apr '23

This was unnecessarily added in commit 09668b441da ("emu10k1 - Add PM support"). Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- v2: - paste subject of referenced commit --- sound/pci/emu10k1/emu10k1_main.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/sound/pci/emu10k1/emu10k1_main.c b/sound/pci/emu10k1/emu10k1_main.c index 3880f359e688..cbfaa4bc70a2 100644 --- a/sound/pci/emu10k1/emu10k1_main.c +++ b/sound/pci/emu10k1/emu10k1_main.c @@ -140,7 +140,7 @@ static const unsigned int i2c_adc_init[][2] = { { 0x15, ADC_MUX_2 }, /* ADC Mixer control. Mic for A2ZS Notebook */ }; -static int snd_emu10k1_init(struct snd_emu10k1 *emu, int enable_ir, int resume) +static int snd_emu10k1_init(struct snd_emu10k1 *emu, int enable_ir) { unsigned int silent_page; int ch; @@ -1975,7 +1975,7 @@ int snd_emu10k1_create(struct snd_card *card, emu->voices[idx].number = idx; } - err = snd_emu10k1_init(emu, enable_ir, 0); + err = snd_emu10k1_init(emu, enable_ir); if (err < 0) return err; #ifdef CONFIG_PM_SLEEP @@ -2068,7 +2068,7 @@ void snd_emu10k1_resume_init(struct snd_emu10k1 *emu) snd_emu10k1_emu1010_init(emu); else snd_emu10k1_ptr_write(emu, AC97SLOT, 0, AC97SLOT_CNTR|AC97SLOT_LFE); - snd_emu10k1_init(emu, emu->enable_ir, 1); + snd_emu10k1_init(emu, emu->enable_ir); } void snd_emu10k1_resume_regs(struct snd_emu10k1 *emu) -- 2.40.0.152.g15d061e6df

2 2

[PATCH v2] ALSA: emu10k1: minor optimizations
by Oswald Buddenhagen 22 Apr '23

22 Apr '23

- In snd_emu10k1_look_for_ctl(), evaluate the cheap condition first - In _snd_emu10k1_{audigy_,}init_efx(), don't use expensive bit setting loops to fill arrays - In snd_emu_proc_ptr_reg_read(), remove useless condition - iobase can be only 0 or 0x20 Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- v2: - fix fill sizes for sblive by using the previous hard-coded numbers. it might be a good idea to introduce constants for that, but that's for another patch. --- sound/pci/emu10k1/emufx.c | 18 +++++++----------- sound/pci/emu10k1/emuproc.c | 5 +---- 2 files changed, 8 insertions(+), 15 deletions(-) diff --git a/sound/pci/emu10k1/emufx.c b/sound/pci/emu10k1/emufx.c index 6cf7c8b1de47..66f450377888 100644 --- a/sound/pci/emu10k1/emufx.c +++ b/sound/pci/emu10k1/emufx.c @@ -641,8 +641,8 @@ snd_emu10k1_look_for_ctl(struct snd_emu10k1 *emu, list_for_each_entry(ctl, &emu->fx8010.gpr_ctl, list) { kcontrol = ctl->kcontrol; if (kcontrol->id.iface == id->iface && - !strcmp(kcontrol->id.name, id->name) && - kcontrol->id.index == id->index) + kcontrol->id.index == id->index && + !strcmp(kcontrol->id.name, id->name)) return ctl; } return NULL; @@ -1213,7 +1213,7 @@ static int snd_emu10k1_audigy_dsp_convert_32_to_2x16( static int _snd_emu10k1_audigy_init_efx(struct snd_emu10k1 *emu) { - int err, i, z, gpr, nctl; + int err, z, gpr, nctl; int bit_shifter16; const int playback = 10; const int capture = playback + (SND_EMU10K1_PLAYBACK_CHANNELS * 2); /* we reserve 10 voices */ @@ -1245,12 +1245,10 @@ static int _snd_emu10k1_audigy_init_efx(struct snd_emu10k1 *emu) icode->code = icode->tram_addr_map + 256; /* clear free GPRs */ - for (i = 0; i < 512; i++) - set_bit(i, icode->gpr_valid); + memset(icode->gpr_valid, 0xff, 512 / 8); /* clear TRAM data & address lines */ - for (i = 0; i < 256; i++) - set_bit(i, icode->tram_valid); + memset(icode->tram_valid, 0xff, 256 / 8); strcpy(icode->name, "Audigy DSP code for ALSA"); ptr = 0; @@ -1886,12 +1884,10 @@ static int _snd_emu10k1_init_efx(struct snd_emu10k1 *emu) icode->code = icode->tram_addr_map + 160; /* clear free GPRs */ - for (i = 0; i < 256; i++) - set_bit(i, icode->gpr_valid); + memset(icode->gpr_valid, 0xff, 256 / 8); /* clear TRAM data & address lines */ - for (i = 0; i < 160; i++) - set_bit(i, icode->tram_valid); + memset(icode->tram_valid, 0xff, 160 / 8); strcpy(icode->name, "SB Live! FX8010 code for ALSA v1.2 by Jaroslav Kysela"); ptr = 0; i = 0; diff --git a/sound/pci/emu10k1/emuproc.c b/sound/pci/emu10k1/emuproc.c index 6e20cca9c98f..bec72dc60a41 100644 --- a/sound/pci/emu10k1/emuproc.c +++ b/sound/pci/emu10k1/emuproc.c @@ -477,10 +477,7 @@ static void snd_emu_proc_ptr_reg_read(struct snd_info_entry *entry, for(i = offset; i < offset+length; i++) { snd_iprintf(buffer, "%02X: ",i); for (j = 0; j < voices; j++) { - if(iobase == 0) - value = snd_ptr_read(emu, 0, i, j); - else - value = snd_ptr_read(emu, 0x20, i, j); + value = snd_ptr_read(emu, iobase, i, j); snd_iprintf(buffer, "%08lX ", value); } snd_iprintf(buffer, "\n"); -- 2.40.0.152.g15d061e6df

2 1

[PATCH] ALSA: emu10k1: fix error codes
by Oswald Buddenhagen 22 Apr '23

22 Apr '23

One might argue that this potentially breaks user space, but a) this is just one driver among many, so it seems unlikely that someone would expect (only) the broken codes and b) it seems unlikely that someone would check these syscalls for particular errors at all, rather than just logging them (this might be debatable for the voice allocator calls). Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- sound/pci/emu10k1/emu10k1_callback.c | 2 +- sound/pci/emu10k1/emufx.c | 4 ++-- sound/pci/emu10k1/io.c | 2 +- sound/pci/emu10k1/voice.c | 2 +- 4 files changed, 5 insertions(+), 5 deletions(-) diff --git a/sound/pci/emu10k1/emu10k1_callback.c b/sound/pci/emu10k1/emu10k1_callback.c index dba1e9fc2eec..5943747eb7db 100644 --- a/sound/pci/emu10k1/emu10k1_callback.c +++ b/sound/pci/emu10k1/emu10k1_callback.c @@ -106,7 +106,7 @@ snd_emu10k1_synth_get_voice(struct snd_emu10k1 *hw) } /* not found */ - return -ENOMEM; + return -EBUSY; } diff --git a/sound/pci/emu10k1/emufx.c b/sound/pci/emu10k1/emufx.c index 6cf7c8b1de47..267d1bab3ee4 100644 --- a/sound/pci/emu10k1/emufx.c +++ b/sound/pci/emu10k1/emufx.c @@ -360,15 +360,15 @@ static int snd_emu10k1_gpr_ctl_put(struct snd_kcontrol *kcontrol, struct snd_ctl break; case EMU10K1_GPR_TRANSLATION_BASS: if ((ctl->count % 5) != 0 || (ctl->count / 5) != ctl->vcount) { - change = -EIO; + change = -EINVAL; goto __error; } for (j = 0; j < 5; j++) snd_emu10k1_ptr_write(emu, emu->gpr_base + ctl->gpr[j * ctl->vcount + i], 0, bass_table[val][j]); break; case EMU10K1_GPR_TRANSLATION_TREBLE: if ((ctl->count % 5) != 0 || (ctl->count / 5) != ctl->vcount) { - change = -EIO; + change = -EINVAL; goto __error; } for (j = 0; j < 5; j++) diff --git a/sound/pci/emu10k1/io.c b/sound/pci/emu10k1/io.c index e15092ce9848..cfcdb33992bf 100644 --- a/sound/pci/emu10k1/io.c +++ b/sound/pci/emu10k1/io.c @@ -226,7 +226,7 @@ int snd_emu10k1_i2c_write(struct snd_emu10k1 *emu, dev_err(emu->card->dev, "status=0x%x, reg=%d, value=%d\n", status, reg, value); /* dump_stack(); */ - err = -EINVAL; + err = -EIO; } spin_unlock(&emu->i2c_lock); diff --git a/sound/pci/emu10k1/voice.c b/sound/pci/emu10k1/voice.c index cbeb8443492c..a5cb932d525a 100644 --- a/sound/pci/emu10k1/voice.c +++ b/sound/pci/emu10k1/voice.c @@ -70,7 +70,7 @@ static int voice_alloc(struct snd_emu10k1 *emu, int type, int number, } if (first_voice == last_voice) - return -ENOMEM; + return -EBUSY; for (i = 0; i < number; i++) { voice = &emu->voices[(first_voice + i) % NUM_G]; -- 2.40.0.152.g15d061e6df

2 3

[PATCH 1/7] ALSA: emu10k1: properly assert E-MU FPGA access constaints
by Oswald Buddenhagen 22 Apr '23

22 Apr '23

Assert the validity of the registers and values, as them being out of range would indicate an error in the driver. Consequently, don't bother returning error codes; they were ignored everywhere anyway. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- include/sound/emu10k1.h | 6 +++--- sound/pci/emu10k1/io.c | 36 +++++++++++++++++------------------- 2 files changed, 20 insertions(+), 22 deletions(-) diff --git a/include/sound/emu10k1.h b/include/sound/emu10k1.h index 39787fecc8d9..01e2e22689bd 100644 --- a/include/sound/emu10k1.h +++ b/include/sound/emu10k1.h @@ -1824,9 +1824,9 @@ unsigned int snd_emu10k1_ptr20_read(struct snd_emu10k1 * emu, unsigned int reg, void snd_emu10k1_ptr20_write(struct snd_emu10k1 *emu, unsigned int reg, unsigned int chn, unsigned int data); int snd_emu10k1_spi_write(struct snd_emu10k1 * emu, unsigned int data); int snd_emu10k1_i2c_write(struct snd_emu10k1 *emu, u32 reg, u32 value); -int snd_emu1010_fpga_write(struct snd_emu10k1 * emu, u32 reg, u32 value); -int snd_emu1010_fpga_read(struct snd_emu10k1 * emu, u32 reg, u32 *value); -int snd_emu1010_fpga_link_dst_src_write(struct snd_emu10k1 * emu, u32 dst, u32 src); +void snd_emu1010_fpga_write(struct snd_emu10k1 *emu, u32 reg, u32 value); +void snd_emu1010_fpga_read(struct snd_emu10k1 *emu, u32 reg, u32 *value); +void snd_emu1010_fpga_link_dst_src_write(struct snd_emu10k1 *emu, u32 dst, u32 src); unsigned int snd_emu10k1_efx_read(struct snd_emu10k1 *emu, unsigned int pc); void snd_emu10k1_intr_enable(struct snd_emu10k1 *emu, unsigned int intrenb); void snd_emu10k1_intr_disable(struct snd_emu10k1 *emu, unsigned int intrenb); diff --git a/sound/pci/emu10k1/io.c b/sound/pci/emu10k1/io.c index e15092ce9848..35bc73d99d04 100644 --- a/sound/pci/emu10k1/io.c +++ b/sound/pci/emu10k1/io.c @@ -233,56 +233,54 @@ int snd_emu10k1_i2c_write(struct snd_emu10k1 *emu, return err; } -int snd_emu1010_fpga_write(struct snd_emu10k1 * emu, u32 reg, u32 value) +void snd_emu1010_fpga_write(struct snd_emu10k1 *emu, u32 reg, u32 value) { unsigned long flags; - if (reg > 0x3f) - return 1; + if (snd_BUG_ON(reg > 0x3f)) + return; reg += 0x40; /* 0x40 upwards are registers. */ - if (value > 0x3f) /* 0 to 0x3f are values */ - return 1; + if (snd_BUG_ON(value > 0x3f)) /* 0 to 0x3f are values */ + return; spin_lock_irqsave(&emu->emu_lock, flags); outl(reg, emu->port + A_IOCFG); udelay(10); outl(reg | 0x80, emu->port + A_IOCFG); /* High bit clocks the value into the fpga. */ udelay(10); outl(value, emu->port + A_IOCFG); udelay(10); outl(value | 0x80 , emu->port + A_IOCFG); /* High bit clocks the value into the fpga. */ spin_unlock_irqrestore(&emu->emu_lock, flags); - - return 0; } -int snd_emu1010_fpga_read(struct snd_emu10k1 * emu, u32 reg, u32 *value) +void snd_emu1010_fpga_read(struct snd_emu10k1 *emu, u32 reg, u32 *value) { unsigned long flags; - if (reg > 0x3f) - return 1; + if (snd_BUG_ON(reg > 0x3f)) + return; reg += 0x40; /* 0x40 upwards are registers. */ spin_lock_irqsave(&emu->emu_lock, flags); outl(reg, emu->port + A_IOCFG); udelay(10); outl(reg | 0x80, emu->port + A_IOCFG); /* High bit clocks the value into the fpga. */ udelay(10); *value = ((inl(emu->port + A_IOCFG) >> 8) & 0x7f); spin_unlock_irqrestore(&emu->emu_lock, flags); - - return 0; } /* Each Destination has one and only one Source, * but one Source can feed any number of Destinations simultaneously. */ -int snd_emu1010_fpga_link_dst_src_write(struct snd_emu10k1 * emu, u32 dst, u32 src) +void snd_emu1010_fpga_link_dst_src_write(struct snd_emu10k1 *emu, u32 dst, u32 src) { - snd_emu1010_fpga_write(emu, 0x00, ((dst >> 8) & 0x3f) ); - snd_emu1010_fpga_write(emu, 0x01, (dst & 0x3f) ); - snd_emu1010_fpga_write(emu, 0x02, ((src >> 8) & 0x3f) ); - snd_emu1010_fpga_write(emu, 0x03, (src & 0x3f) ); - - return 0; + if (snd_BUG_ON(dst & ~0x71f)) + return; + if (snd_BUG_ON(src & ~0x71f)) + return; + snd_emu1010_fpga_write(emu, 0x00, dst >> 8); + snd_emu1010_fpga_write(emu, 0x01, dst & 0x1f); + snd_emu1010_fpga_write(emu, 0x02, src >> 8); + snd_emu1010_fpga_write(emu, 0x03, src & 0x1f); } void snd_emu10k1_intr_enable(struct snd_emu10k1 *emu, unsigned int intrenb) -- 2.40.0.152.g15d061e6df

2 10

[PATCH 1/7] ALSA: emu10k1: drop redundant snd_emu10k1_efx_playback_hw_free()
by Oswald Buddenhagen 22 Apr '23

22 Apr '23

Or actually, replace snd_emu10k1_playback_hw_free() with it, as that is a subset. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- sound/pci/emu10k1/emupcm.c | 32 +------------------------------- 1 file changed, 1 insertion(+), 31 deletions(-) diff --git a/sound/pci/emu10k1/emupcm.c b/sound/pci/emu10k1/emupcm.c index 48af77ae8020..b89382aa4db6 100644 --- a/sound/pci/emu10k1/emupcm.c +++ b/sound/pci/emu10k1/emupcm.c @@ -429,36 +429,6 @@ static int snd_emu10k1_playback_hw_params(struct snd_pcm_substream *substream, } static int snd_emu10k1_playback_hw_free(struct snd_pcm_substream *substream) -{ - struct snd_emu10k1 *emu = snd_pcm_substream_chip(substream); - struct snd_pcm_runtime *runtime = substream->runtime; - struct snd_emu10k1_pcm *epcm; - - if (runtime->private_data == NULL) - return 0; - epcm = runtime->private_data; - if (epcm->extra) { - snd_emu10k1_voice_free(epcm->emu, epcm->extra); - epcm->extra = NULL; - } - if (epcm->voices[1]) { - snd_emu10k1_voice_free(epcm->emu, epcm->voices[1]); - epcm->voices[1] = NULL; - } - if (epcm->voices[0]) { - snd_emu10k1_voice_free(epcm->emu, epcm->voices[0]); - epcm->voices[0] = NULL; - } - if (epcm->memblk) { - snd_emu10k1_free_pages(emu, epcm->memblk); - epcm->memblk = NULL; - epcm->start_addr = 0; - } - snd_pcm_lib_free_pages(substream); - return 0; -} - -static int snd_emu10k1_efx_playback_hw_free(struct snd_pcm_substream *substream) { struct snd_emu10k1 *emu = snd_pcm_substream_chip(substream); struct snd_pcm_runtime *runtime = substream->runtime; @@ -1372,7 +1342,7 @@ static const struct snd_pcm_ops snd_emu10k1_efx_playback_ops = { .open = snd_emu10k1_efx_playback_open, .close = snd_emu10k1_efx_playback_close, .hw_params = snd_emu10k1_playback_hw_params, - .hw_free = snd_emu10k1_efx_playback_hw_free, + .hw_free = snd_emu10k1_playback_hw_free, .prepare = snd_emu10k1_efx_playback_prepare, .trigger = snd_emu10k1_efx_playback_trigger, .pointer = snd_emu10k1_efx_playback_pointer, -- 2.40.0.152.g15d061e6df

2 12

[PATCH] ALSA: emu10k1: minor optimizations
by Oswald Buddenhagen 22 Apr '23

22 Apr '23

- In snd_emu10k1_look_for_ctl(), evaluate the cheap condition first - In _snd_emu10k1_{audigy_,}init_efx(), don't use expensive bit setting loops to fill arrays - In snd_emu_proc_ptr_reg_read(), remove useless condition - iobase can be only 0 or 0x20 Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- sound/pci/emu10k1/emufx.c | 18 +++++++----------- sound/pci/emu10k1/emuproc.c | 5 +---- 2 files changed, 8 insertions(+), 15 deletions(-) diff --git a/sound/pci/emu10k1/emufx.c b/sound/pci/emu10k1/emufx.c index 6cf7c8b1de47..704f6564668e 100644 --- a/sound/pci/emu10k1/emufx.c +++ b/sound/pci/emu10k1/emufx.c @@ -641,8 +641,8 @@ snd_emu10k1_look_for_ctl(struct snd_emu10k1 *emu, list_for_each_entry(ctl, &emu->fx8010.gpr_ctl, list) { kcontrol = ctl->kcontrol; if (kcontrol->id.iface == id->iface && - !strcmp(kcontrol->id.name, id->name) && - kcontrol->id.index == id->index) + kcontrol->id.index == id->index && + !strcmp(kcontrol->id.name, id->name)) return ctl; } return NULL; @@ -1213,7 +1213,7 @@ static int snd_emu10k1_audigy_dsp_convert_32_to_2x16( static int _snd_emu10k1_audigy_init_efx(struct snd_emu10k1 *emu) { - int err, i, z, gpr, nctl; + int err, z, gpr, nctl; int bit_shifter16; const int playback = 10; const int capture = playback + (SND_EMU10K1_PLAYBACK_CHANNELS * 2); /* we reserve 10 voices */ @@ -1245,12 +1245,10 @@ static int _snd_emu10k1_audigy_init_efx(struct snd_emu10k1 *emu) icode->code = icode->tram_addr_map + 256; /* clear free GPRs */ - for (i = 0; i < 512; i++) - set_bit(i, icode->gpr_valid); + memset(icode->gpr_valid, 0xff, sizeof(icode->gpr_valid)); /* clear TRAM data & address lines */ - for (i = 0; i < 256; i++) - set_bit(i, icode->tram_valid); + memset(icode->tram_valid, 0xff, sizeof(icode->tram_valid)); strcpy(icode->name, "Audigy DSP code for ALSA"); ptr = 0; @@ -1886,12 +1884,10 @@ static int _snd_emu10k1_init_efx(struct snd_emu10k1 *emu) icode->code = icode->tram_addr_map + 160; /* clear free GPRs */ - for (i = 0; i < 256; i++) - set_bit(i, icode->gpr_valid); + memset(icode->gpr_valid, 0xff, sizeof(icode->gpr_valid)); /* clear TRAM data & address lines */ - for (i = 0; i < 160; i++) - set_bit(i, icode->tram_valid); + memset(icode->tram_valid, 0xff, sizeof(icode->tram_valid)); strcpy(icode->name, "SB Live! FX8010 code for ALSA v1.2 by Jaroslav Kysela"); ptr = 0; i = 0; diff --git a/sound/pci/emu10k1/emuproc.c b/sound/pci/emu10k1/emuproc.c index 6e20cca9c98f..bec72dc60a41 100644 --- a/sound/pci/emu10k1/emuproc.c +++ b/sound/pci/emu10k1/emuproc.c @@ -477,10 +477,7 @@ static void snd_emu_proc_ptr_reg_read(struct snd_info_entry *entry, for(i = offset; i < offset+length; i++) { snd_iprintf(buffer, "%02X: ",i); for (j = 0; j < voices; j++) { - if(iobase == 0) - value = snd_ptr_read(emu, 0, i, j); - else - value = snd_ptr_read(emu, 0x20, i, j); + value = snd_ptr_read(emu, iobase, i, j); snd_iprintf(buffer, "%08lX ", value); } snd_iprintf(buffer, "\n"); -- 2.40.0.152.g15d061e6df

2 1

[PATCH] ASoC: max98088: make it selectable
by Maxim Kochetkov 21 Apr '23

21 Apr '23

There is no way to select max98088 from menuconfig right now. Add a Kconfig menu description to allow building the driver standalone. Signed-off-by: Maxim Kochetkov <fido_max(a)inbox.ru> --- sound/soc/codecs/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 79d2362ad055..8020097d4e4c 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -1090,7 +1090,7 @@ config SND_SOC_MAX98088 depends on I2C config SND_SOC_MAX98090 - tristate + tristate "Maxim MAX98090 CODEC" depends on I2C config SND_SOC_MAX98095 -- 2.39.2

3 7

[PATCH] ASoC: rt715: Use maple tree register cache
by Mark Brown 21 Apr '23

21 Apr '23

regmap has introduced a maple tree based register cache which makes use of this more advanced data structure which has been added to the kernel recently. Maple trees are much flatter than rbtrees, meaning that they do not grow to such depths when the register map is sparse which makes access a bit more efficient. The maple tree cache type is still a bit of a work in progress but should be effective for some devices already. RT715 seems like a good candidate for maple tree. It is a SoundWire MBQ device and therefore supports only single register read/write operations which do not use raw I/O and will therefore save the cost of converting to and from device native format when accessing the cache while not having a negative impact from the current lack of bulk operations in maple tree cache sync. It has a moderately large and quite sparse register map which is a good fit for storing in a maple tree. Convert to use maple tree. There should be little if any visible difference at runtime. Signed-off-by: Mark Brown <broonie(a)kernel.org> --- sound/soc/codecs/rt715-sdw.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/codecs/rt715-sdw.c b/sound/soc/codecs/rt715-sdw.c index 4e61e16470ed..5ffe9a00dfd8 100644 --- a/sound/soc/codecs/rt715-sdw.c +++ b/sound/soc/codecs/rt715-sdw.c @@ -354,7 +354,7 @@ static const struct regmap_config rt715_regmap = { .max_register = 0x752039, /* Maximum number of register */ .reg_defaults = rt715_reg_defaults, /* Defaults */ .num_reg_defaults = ARRAY_SIZE(rt715_reg_defaults), - .cache_type = REGCACHE_RBTREE, + .cache_type = REGCACHE_MAPLE, .use_single_read = true, .use_single_write = true, .reg_read = rt715_sdw_read, --- base-commit: f033c26de5a5734625d2dd1dc196745fae186f1b change-id: 20230412-asoc-rt715-maple-185f657063f4 Best regards, -- Mark Brown <broonie(a)kernel.org>

1 0

[RFC][PATCH 0/4] ASoC: fsl: cleanup platform
by Kuninori Morimoto 21 Apr '23

21 Apr '23

Hi Mark Cc Shengjiu The driver which is using soc-generic-dmaengine-pcm is a little bit difficult to notice about it, because it prepares own Component, but shares same component->dev with CPU Component. Some fsl driver is using soc-generic-dmaengine-pcm as Platform Component. When binding CPU/Codec, it finds relevant Component, and checks target DAI. If it it was target DAI, ASoC binds its Component to Card. In Platform case, it finds relevant Component and bind it. It doesn't check DAI. This means, we can share CPU dlc with Platform in this case. It is more reasonable / understandable / intuitive. This patch-set share CPU dlc with Platform, and adds such comment. Because I can't test this patch-set, thus I added [RFC] on Subject. Please test these. This patch-set requests Tested-by. Link: https://lore.kernel.org/r/87o7ojjd06.wl-kuninori.morimoto.gx@renesas.com Link: https://lore.kernel.org/r/1681900158-17428-1-git-send-email-shengjiu.wang@n… Kuninori Morimoto (4): ASoC: fsl: imx-es8328: cleanup platform which is using Generic DMA ASoC: fsl: imx-spdif: cleanup platform which is using Generic DMA ASoC: fsl: imx-audmix: cleanup platform which is using Generic DMA ASoC: fsl: imx-audmix: remove dummy dai_link->platform sound/soc/fsl/imx-audmix.c | 22 +++++++++++----------- sound/soc/fsl/imx-es8328.c | 11 +++++++---- sound/soc/fsl/imx-spdif.c | 11 +++++++---- 3 files changed, 25 insertions(+), 19 deletions(-) -- 2.25.1

3 6

[PATCH] ASoC: cs35l56: Remove duplicate mbox log messages
by Richard Fitzgerald 21 Apr '23

21 Apr '23

From: Simon Trimmer <simont(a)opensource.cirrus.com> cs35l56_mbox_send() logs a warning when sending a mbox command fails so the callers can be simplified. Signed-off-by: Simon Trimmer <simont(a)opensource.cirrus.com> Signed-off-by: Richard Fitzgerald <rf(a)opensource.cirrus.com> --- sound/soc/codecs/cs35l56.c | 8 ++------ 1 file changed, 2 insertions(+), 6 deletions(-) diff --git a/sound/soc/codecs/cs35l56.c b/sound/soc/codecs/cs35l56.c index c0a857cfb8cb..46762f7f1449 100644 --- a/sound/soc/codecs/cs35l56.c +++ b/sound/soc/codecs/cs35l56.c @@ -859,10 +859,8 @@ static void cs35l56_dsp_work(struct work_struct *work) } ret = cs35l56_mbox_send(cs35l56, CS35L56_MBOX_CMD_SHUTDOWN); - if (ret) { - dev_dbg(cs35l56->dev, "%s: CS35L56_MBOX_CMD_SHUTDOWN ret %d\n", __func__, ret); + if (ret) goto err; - } if (cs35l56->rev < CS35L56_REVID_B0) reg = CS35L56_DSP1_PM_CUR_STATE_A1; @@ -1033,9 +1031,7 @@ int cs35l56_runtime_suspend(struct device *dev) * Enable auto-hibernate. If it is woken by some other wake source * it will automatically return to hibernate. */ - ret = cs35l56_mbox_send(cs35l56, CS35L56_MBOX_CMD_ALLOW_AUTO_HIBERNATE); - if (ret) - dev_warn(cs35l56->dev, "ALLOW_HIBERNATE failed: %d\n", ret); + cs35l56_mbox_send(cs35l56, CS35L56_MBOX_CMD_ALLOW_AUTO_HIBERNATE); /* * Must enter cache-only first so there can't be any more register -- 2.30.2

2 1

[PATCH 0/2] ASoC: SOF: pcm/Intel: Pause-resume improvements for IPC4
by Peter Ujfalusi 21 Apr '23

21 Apr '23

Hi, last minute patch for correct the pasue/resume operation with IPC4. The issues are hardto reproduce and needs extended stress testing to be hit, in which case the audio breaks due to DMA errors. Regards, Peter --- Ranjani Sridharan (2): ASoC: SOF: Intel: hda: Do not stop/start DMA during pause/release ASoC: SOF: pcm: Add an option to skip platform trigger during stop sound/soc/sof/intel/hda-stream.c | 11 ++++++++++- sound/soc/sof/ipc4-pcm.c | 3 ++- sound/soc/sof/pcm.c | 23 +++++++++++++++-------- sound/soc/sof/sof-audio.c | 22 ++++++++++++++-------- sound/soc/sof/sof-audio.h | 6 ++++++ 5 files changed, 47 insertions(+), 18 deletions(-) -- 2.40.0

2 3

[PATCH] ASoC: SOF: Intel: Split the set_power_op for IPC3 and IPC4
by Peter Ujfalusi 21 Apr '23

21 Apr '23

From: Ranjani Sridharan <ranjani.sridharan(a)linux.intel.com> Suspending to S0iX with IPC3 requires the PM_GATE IPC to be sent again to stop the DMA trace. But with IPC4, this is not needed as the trace is stopped with the LARGE_CONFIG_SET IPC. Also, sending the MOD_D0IX IPC to set the D0I3 state again when the DSP is in D0I3 already results in an imbalance in PM runtime states in the firmware. So split the set_power_state ops for IPC3 and IPC4 to avoid sending the MOD_D0IX IPC when the DSP is already in D0I3 with IPC4. Signed-off-by: Ranjani Sridharan <ranjani.sridharan(a)linux.intel.com> Reviewed-by: Rander Wang <rander.wang(a)intel.com> Reviewed-by: Bard Liao <yung-chuan.liao(a)linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi(a)linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart(a)linux.intel.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi(a)linux.intel.com> --- Mark, last minute patch for 6.4 as the issue this patch addressing was discovered and fixed recently for IPC4. Regards, Peter sound/soc/sof/intel/apl.c | 4 ++ sound/soc/sof/intel/cnl.c | 4 ++ sound/soc/sof/intel/hda-common-ops.c | 1 - sound/soc/sof/intel/hda-dsp.c | 60 ++++++++++++++++++---------- sound/soc/sof/intel/hda.h | 6 ++- sound/soc/sof/intel/icl.c | 4 ++ sound/soc/sof/intel/mtl.c | 2 + sound/soc/sof/intel/tgl.c | 4 ++ 8 files changed, 60 insertions(+), 25 deletions(-) diff --git a/sound/soc/sof/intel/apl.c b/sound/soc/sof/intel/apl.c index 0e7a7e4ad976..e1f25a8f0c32 100644 --- a/sound/soc/sof/intel/apl.c +++ b/sound/soc/sof/intel/apl.c @@ -48,6 +48,8 @@ int sof_apl_ops_init(struct snd_sof_dev *sdev) /* debug */ sof_apl_ops.ipc_dump = hda_ipc_dump; + + sof_apl_ops.set_power_state = hda_dsp_set_power_state_ipc3; } if (sdev->pdata->ipc_type == SOF_INTEL_IPC4) { @@ -73,6 +75,8 @@ int sof_apl_ops_init(struct snd_sof_dev *sdev) /* debug */ sof_apl_ops.ipc_dump = hda_ipc4_dump; + + sof_apl_ops.set_power_state = hda_dsp_set_power_state_ipc4; } /* set DAI driver ops */ diff --git a/sound/soc/sof/intel/cnl.c b/sound/soc/sof/intel/cnl.c index a08a77fa946b..a95222e53ecf 100644 --- a/sound/soc/sof/intel/cnl.c +++ b/sound/soc/sof/intel/cnl.c @@ -395,6 +395,8 @@ int sof_cnl_ops_init(struct snd_sof_dev *sdev) /* debug */ sof_cnl_ops.ipc_dump = cnl_ipc_dump; + + sof_cnl_ops.set_power_state = hda_dsp_set_power_state_ipc3; } if (sdev->pdata->ipc_type == SOF_INTEL_IPC4) { @@ -420,6 +422,8 @@ int sof_cnl_ops_init(struct snd_sof_dev *sdev) /* debug */ sof_cnl_ops.ipc_dump = cnl_ipc4_dump; + + sof_cnl_ops.set_power_state = hda_dsp_set_power_state_ipc4; } /* set DAI driver ops */ diff --git a/sound/soc/sof/intel/hda-common-ops.c b/sound/soc/sof/intel/hda-common-ops.c index 397303b3ac9d..8e1cd0babd32 100644 --- a/sound/soc/sof/intel/hda-common-ops.c +++ b/sound/soc/sof/intel/hda-common-ops.c @@ -89,7 +89,6 @@ struct snd_sof_dsp_ops sof_hda_common_ops = { .runtime_resume = hda_dsp_runtime_resume, .runtime_idle = hda_dsp_runtime_idle, .set_hw_params_upon_resume = hda_dsp_set_hw_params_upon_resume, - .set_power_state = hda_dsp_set_power_state, /* ALSA HW info flags */ .hw_info = SNDRV_PCM_INFO_MMAP | diff --git a/sound/soc/sof/intel/hda-dsp.c b/sound/soc/sof/intel/hda-dsp.c index 77df536cf901..44f39a520bb3 100644 --- a/sound/soc/sof/intel/hda-dsp.c +++ b/sound/soc/sof/intel/hda-dsp.c @@ -574,31 +574,11 @@ static void hda_dsp_state_log(struct snd_sof_dev *sdev) * is called again either because of a new IPC sent to the DSP or * during system suspend/resume. */ -int hda_dsp_set_power_state(struct snd_sof_dev *sdev, - const struct sof_dsp_power_state *target_state) +static int hda_dsp_set_power_state(struct snd_sof_dev *sdev, + const struct sof_dsp_power_state *target_state) { int ret = 0; - /* - * When the DSP is already in D0I3 and the target state is D0I3, - * it could be the case that the DSP is in D0I3 during S0 - * and the system is suspending to S0Ix. Therefore, - * hda_dsp_set_D0_state() must be called to disable trace DMA - * by sending the PM_GATE IPC to the FW. - */ - if (target_state->substate == SOF_HDA_DSP_PM_D0I3 && - sdev->system_suspend_target == SOF_SUSPEND_S0IX) - goto set_state; - - /* - * For all other cases, return without doing anything if - * the DSP is already in the target state. - */ - if (target_state->state == sdev->dsp_power_state.state && - target_state->substate == sdev->dsp_power_state.substate) - return 0; - -set_state: switch (target_state->state) { case SOF_DSP_PM_D0: ret = hda_dsp_set_D0_state(sdev, target_state); @@ -630,6 +610,42 @@ int hda_dsp_set_power_state(struct snd_sof_dev *sdev, return ret; } +int hda_dsp_set_power_state_ipc3(struct snd_sof_dev *sdev, + const struct sof_dsp_power_state *target_state) +{ + /* + * When the DSP is already in D0I3 and the target state is D0I3, + * it could be the case that the DSP is in D0I3 during S0 + * and the system is suspending to S0Ix. Therefore, + * hda_dsp_set_D0_state() must be called to disable trace DMA + * by sending the PM_GATE IPC to the FW. + */ + if (target_state->substate == SOF_HDA_DSP_PM_D0I3 && + sdev->system_suspend_target == SOF_SUSPEND_S0IX) + return hda_dsp_set_power_state(sdev, target_state); + + /* + * For all other cases, return without doing anything if + * the DSP is already in the target state. + */ + if (target_state->state == sdev->dsp_power_state.state && + target_state->substate == sdev->dsp_power_state.substate) + return 0; + + return hda_dsp_set_power_state(sdev, target_state); +} + +int hda_dsp_set_power_state_ipc4(struct snd_sof_dev *sdev, + const struct sof_dsp_power_state *target_state) +{ + /* Return without doing anything if the DSP is already in the target state */ + if (target_state->state == sdev->dsp_power_state.state && + target_state->substate == sdev->dsp_power_state.substate) + return 0; + + return hda_dsp_set_power_state(sdev, target_state); +} + /* * Audio DSP states may transform as below:- * diff --git a/sound/soc/sof/intel/hda.h b/sound/soc/sof/intel/hda.h index 0e0cfa81a8f2..c4befacde23e 100644 --- a/sound/soc/sof/intel/hda.h +++ b/sound/soc/sof/intel/hda.h @@ -584,8 +584,10 @@ void hda_dsp_ipc_int_enable(struct snd_sof_dev *sdev); void hda_dsp_ipc_int_disable(struct snd_sof_dev *sdev); bool hda_dsp_core_is_enabled(struct snd_sof_dev *sdev, unsigned int core_mask); -int hda_dsp_set_power_state(struct snd_sof_dev *sdev, - const struct sof_dsp_power_state *target_state); +int hda_dsp_set_power_state_ipc3(struct snd_sof_dev *sdev, + const struct sof_dsp_power_state *target_state); +int hda_dsp_set_power_state_ipc4(struct snd_sof_dev *sdev, + const struct sof_dsp_power_state *target_state); int hda_dsp_suspend(struct snd_sof_dev *sdev, u32 target_state); int hda_dsp_resume(struct snd_sof_dev *sdev); diff --git a/sound/soc/sof/intel/icl.c b/sound/soc/sof/intel/icl.c index 435941a1692f..0f249efc6a5a 100644 --- a/sound/soc/sof/intel/icl.c +++ b/sound/soc/sof/intel/icl.c @@ -116,6 +116,8 @@ int sof_icl_ops_init(struct snd_sof_dev *sdev) /* debug */ sof_icl_ops.ipc_dump = cnl_ipc_dump; + + sof_icl_ops.set_power_state = hda_dsp_set_power_state_ipc3; } if (sdev->pdata->ipc_type == SOF_INTEL_IPC4) { @@ -141,6 +143,8 @@ int sof_icl_ops_init(struct snd_sof_dev *sdev) /* debug */ sof_icl_ops.ipc_dump = cnl_ipc4_dump; + + sof_icl_ops.set_power_state = hda_dsp_set_power_state_ipc4; } /* debug */ diff --git a/sound/soc/sof/intel/mtl.c b/sound/soc/sof/intel/mtl.c index 9f969e07fc27..46caf3ccde66 100644 --- a/sound/soc/sof/intel/mtl.c +++ b/sound/soc/sof/intel/mtl.c @@ -668,6 +668,8 @@ int sof_mtl_ops_init(struct snd_sof_dev *sdev) /* set DAI ops */ hda_set_dai_drv_ops(sdev, &sof_mtl_ops); + sof_mtl_ops.set_power_state = hda_dsp_set_power_state_ipc4; + return 0; }; EXPORT_SYMBOL_NS(sof_mtl_ops_init, SND_SOC_SOF_INTEL_HDA_COMMON); diff --git a/sound/soc/sof/intel/tgl.c b/sound/soc/sof/intel/tgl.c index 58ac3a46e6a7..2713b7dc7931 100644 --- a/sound/soc/sof/intel/tgl.c +++ b/sound/soc/sof/intel/tgl.c @@ -71,6 +71,8 @@ int sof_tgl_ops_init(struct snd_sof_dev *sdev) /* debug */ sof_tgl_ops.ipc_dump = cnl_ipc_dump; + + sof_tgl_ops.set_power_state = hda_dsp_set_power_state_ipc3; } if (sdev->pdata->ipc_type == SOF_INTEL_IPC4) { @@ -96,6 +98,8 @@ int sof_tgl_ops_init(struct snd_sof_dev *sdev) /* debug */ sof_tgl_ops.ipc_dump = cnl_ipc4_dump; + + sof_tgl_ops.set_power_state = hda_dsp_set_power_state_ipc4; } /* set DAI driver ops */ -- 2.40.0

2 1

[PATCH] ASoC: es8316: Don't use ranges based register lookup for a single register
by Mark Brown 21 Apr '23

21 Apr '23

The es8316 driver uses a register range to specify the single volatile register it has. While the cost will be in the noise this is a bunch of overhead compared to just having a volatile_reg() callback so switch to the callback. Signed-off-by: Mark Brown <broonie(a)kernel.org> --- sound/soc/codecs/es8316.c | 19 ++++++++++--------- 1 file changed, 10 insertions(+), 9 deletions(-) diff --git a/sound/soc/codecs/es8316.c b/sound/soc/codecs/es8316.c index 056c3082fe02..1736a905abdb 100644 --- a/sound/soc/codecs/es8316.c +++ b/sound/soc/codecs/es8316.c @@ -803,14 +803,15 @@ static const struct snd_soc_component_driver soc_component_dev_es8316 = { .endianness = 1, }; -static const struct regmap_range es8316_volatile_ranges[] = { - regmap_reg_range(ES8316_GPIO_FLAG, ES8316_GPIO_FLAG), -}; - -static const struct regmap_access_table es8316_volatile_table = { - .yes_ranges = es8316_volatile_ranges, - .n_yes_ranges = ARRAY_SIZE(es8316_volatile_ranges), -}; +static bool es8316_volatile_reg(struct device *dev, unsigned int reg) +{ + switch (reg) { + case ES8316_GPIO_FLAG: + return true; + default: + return false; + } +} static const struct regmap_config es8316_regmap = { .reg_bits = 8, @@ -818,7 +819,7 @@ static const struct regmap_config es8316_regmap = { .use_single_read = true, .use_single_write = true, .max_register = 0x53, - .volatile_table = &es8316_volatile_table, + .volatile_reg = es8316_volatile_reg, .cache_type = REGCACHE_RBTREE, }; --- base-commit: e8d018dd0257f744ca50a729e3d042cf2ec9da65 change-id: 20230419-asoc-es8316-volatile-5083c880627d Best regards, -- Mark Brown <broonie(a)kernel.org>

1 1

[PATCH 0/7] ASoC: Intel: boards: updates for 6.4
by Pierre-Louis Bossart 21 Apr '23

21 Apr '23

Preparation of ALC712 support with different types of SoundWire devices per link, new RaptorLake SoundWire device, better error handling for Cirrus devices and cosmetic changes for Max98373. Bard Liao (3): ASoC: Intel: sof_sdw: set codec_num = 1 if the device is not aggregated ASoC: Intel: sof_sdw: support different devices on the same sdw link ASoC: Intel: sof_sdw: append codec type to dai link name Curtis Malainey (1): ASoC: Intel: sof_cirrus_common: Guard against missing buses Yong Zhi (2): ASoC: Intel: sof_sdw: remove late_probe flag in struct sof_sdw_codec_info ASoC: Intel: sof_sdw_max98373: change sof_sdw_mx8373_late_probe to static call apoorv (1): ASoC: Intel: soc-acpi: Add entry for rt711-sdca-sdw at link 2 in RPL match table sound/soc/intel/boards/sof_cirrus_common.c | 7 +- sound/soc/intel/boards/sof_sdw.c | 181 ++++++++++++------ sound/soc/intel/boards/sof_sdw_common.h | 3 - sound/soc/intel/boards/sof_sdw_max98373.c | 22 +-- .../intel/common/soc-acpi-intel-rpl-match.c | 17 +- 5 files changed, 152 insertions(+), 78 deletions(-) -- 2.37.2

2 8

[PATCH v2 0/2] ASoC: SOF: add no_reply IPC calls
by Pierre-Louis Bossart 21 Apr '23

21 Apr '23

Simplify IPC messages to avoid passing a reply structure that is not used later. Changes since v1: fixed rebase issue leading to allmodconfig compilation error Curtis Malainey (2): ASoC: SOF: ipc: Add no reply inline calls ASoC: SOF: Use no_reply calls for TX sound/soc/sof/compress.c | 8 ++---- sound/soc/sof/intel/hda-loader.c | 2 +- sound/soc/sof/ipc3-dtrace.c | 12 +++------ sound/soc/sof/ipc3-pcm.c | 6 ++--- sound/soc/sof/ipc3-topology.c | 33 +++++++---------------- sound/soc/sof/ipc3.c | 12 +++------ sound/soc/sof/ipc4-pcm.c | 6 ++--- sound/soc/sof/ipc4-topology.c | 10 +++---- sound/soc/sof/sof-client-ipc-flood-test.c | 3 +-- sound/soc/sof/sof-client-probes-ipc3.c | 12 +++------ sound/soc/sof/sof-client-probes-ipc4.c | 4 +-- sound/soc/sof/sof-client.h | 4 +++ sound/soc/sof/sof-priv.h | 10 +++++++ 13 files changed, 51 insertions(+), 71 deletions(-) -- 2.37.2

2 3

[PATCH 0/2] ASoC: SOF: add no_reply IPC calls
by Pierre-Louis Bossart 21 Apr '23

21 Apr '23

Simplify IPC messages to avoid passing a reply structure that is not used later. Curtis Malainey (2): ASoC: SOF: ipc: Add no reply inline calls ASoC: SOF: Use no_reply calls for TX sound/soc/sof/compress.c | 12 +++------ sound/soc/sof/intel/hda-loader.c | 2 +- sound/soc/sof/ipc3-dtrace.c | 12 +++------ sound/soc/sof/ipc3-pcm.c | 6 ++--- sound/soc/sof/ipc3-topology.c | 33 +++++++---------------- sound/soc/sof/ipc3.c | 12 +++------ sound/soc/sof/ipc4-pcm.c | 6 ++--- sound/soc/sof/ipc4-topology.c | 10 +++---- sound/soc/sof/sof-client-ipc-flood-test.c | 3 +-- sound/soc/sof/sof-client-probes-ipc3.c | 12 +++------ sound/soc/sof/sof-client-probes-ipc4.c | 4 +-- sound/soc/sof/sof-client.h | 4 +++ sound/soc/sof/sof-priv.h | 10 +++++++ 13 files changed, 52 insertions(+), 74 deletions(-) -- 2.37.2

3 7

[PATCH] usb-audio: Rate limit usb_set_interface error reporting
by Chris Down 21 Apr '23

21 Apr '23

When an error occurs during USB disconnection sometimes things can go wrong as endpoint_set_interface may end up being called repeatedly. For example: % dmesg --notime | grep 'usb 3-7.1.4' | sort | uniq -c | head -2 3069 usb 3-7.1.4: 1:1: usb_set_interface failed (-19) 908 usb 3-7.1.4: 1:1: usb_set_interface failed (-71) In my case, there sometimes are hundreds of these usb_set_interface failure messages a second when I disconnect the hub that has my USB audio device. These messages can take a huge amount of the kmsg ringbuffer and don't provide any extra information over the previous ones, so ratelimit them. Signed-off-by: Chris Down <chris(a)chrisdown.name> --- sound/usb/endpoint.c | 5 +++-- sound/usb/usbaudio.h | 2 ++ 2 files changed, 5 insertions(+), 2 deletions(-) diff --git a/sound/usb/endpoint.c b/sound/usb/endpoint.c index 647fa054d8b1..2cd99cc8c360 100644 --- a/sound/usb/endpoint.c +++ b/sound/usb/endpoint.c @@ -916,8 +916,9 @@ static int endpoint_set_interface(struct snd_usb_audio *chip, ep->iface, altset, ep->ep_num); err = usb_set_interface(chip->dev, ep->iface, altset); if (err < 0) { - usb_audio_err(chip, "%d:%d: usb_set_interface failed (%d)\n", - ep->iface, altset, err); + usb_audio_err_ratelimited( + chip, "%d:%d: usb_set_interface failed (%d)\n", + ep->iface, altset, err); return err; } diff --git a/sound/usb/usbaudio.h b/sound/usb/usbaudio.h index f5a8dca66457..38a85b2c9a73 100644 --- a/sound/usb/usbaudio.h +++ b/sound/usb/usbaudio.h @@ -67,6 +67,8 @@ struct snd_usb_audio { #define usb_audio_err(chip, fmt, args...) \ dev_err(&(chip)->dev->dev, fmt, ##args) +#define usb_audio_err_ratelimited(chip, fmt, args...) \ + dev_err_ratelimited(&(chip)->dev->dev, fmt, ##args) #define usb_audio_warn(chip, fmt, args...) \ dev_warn(&(chip)->dev->dev, fmt, ##args) #define usb_audio_info(chip, fmt, args...) \ -- 2.40.0

2 5

[PATCH] ALSA: emu10k1: properly assert DSP init constraints
by Oswald Buddenhagen 21 Apr '23

21 Apr '23

If these are hit, we've already trashed kernel space. There is no recovery from that. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- sound/pci/emu10k1/emufx.c | 21 +++++---------------- 1 file changed, 5 insertions(+), 16 deletions(-) diff --git a/sound/pci/emu10k1/emufx.c b/sound/pci/emu10k1/emufx.c index 6cf7c8b1de47..f6f05219f7fc 100644 --- a/sound/pci/emu10k1/emufx.c +++ b/sound/pci/emu10k1/emufx.c @@ -1773,22 +1773,19 @@ A_OP(icode, &ptr, iMAC0, A_GPR(var), A_GPR(var), A_GPR(vol), A_EXTIN(input)) * ok, set up done.. */ - if (gpr > tmp) { - snd_BUG(); - err = -EIO; - goto __err; - } + BUG_ON(gpr > tmp); + BUG_ON(nctl > SND_EMU10K1_GPR_CONTROLS); + /* clear remaining instruction memory */ while (ptr < 0x400) A_OP(icode, &ptr, 0x0f, 0xc0, 0xc0, 0xcf, 0xc0); icode->gpr_add_control_count = nctl; icode->gpr_add_controls = controls; emu->support_tlv = 1; /* support TLV */ err = snd_emu10k1_icode_poke(emu, icode, true); emu->support_tlv = 0; /* clear again */ -__err: kfree(controls); __err_ctrls: kfree(icode->gpr_map); @@ -2391,16 +2388,8 @@ static int _snd_emu10k1_init_efx(struct snd_emu10k1 *emu) } - if (gpr > tmp) { - snd_BUG(); - err = -EIO; - goto __err; - } - if (i > SND_EMU10K1_GPR_CONTROLS) { - snd_BUG(); - err = -EIO; - goto __err; - } + BUG_ON(gpr > tmp); + BUG_ON(i > SND_EMU10K1_GPR_CONTROLS); /* clear remaining instruction memory */ while (ptr < 0x200) -- 2.40.0.152.g15d061e6df

2 3

[PATCH] ALSA: emu10k1: clarify various fx8010.*_mask fields
by Oswald Buddenhagen 21 Apr '23

21 Apr '23

extin_mask and extout_mask are used only by the SbLive! microcode, so they have no effect on Audigy. Eliminate fxbus_mask entirely, as it wasn't actually used for anything. As a drive-by, remove the pointless pad1 field from struct snd_emu10k1_fx8010 - it is not visible to user space, so it has no binary compatibility constraints. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- include/sound/emu10k1.h | 6 ++---- sound/pci/emu10k1/emu10k1_main.c | 7 ++++--- sound/pci/emu10k1/emufx.c | 9 ++++----- 3 files changed, 10 insertions(+), 12 deletions(-) diff --git a/include/sound/emu10k1.h b/include/sound/emu10k1.h index 39787fecc8d9..3407ca4a1210 100644 --- a/include/sound/emu10k1.h +++ b/include/sound/emu10k1.h @@ -1599,10 +1599,8 @@ struct snd_emu10k1_fx8010_pcm { }; struct snd_emu10k1_fx8010 { - unsigned short fxbus_mask; /* used FX buses (bitmask) */ - unsigned short extin_mask; /* used external inputs (bitmask) */ - unsigned short extout_mask; /* used external outputs (bitmask) */ - unsigned short pad1; + unsigned short extin_mask; /* used external inputs (bitmask); not used for Audigy */ + unsigned short extout_mask; /* used external outputs (bitmask); not used for Audigy */ unsigned int itram_size; /* internal TRAM size in samples */ struct snd_dma_buffer etram_pages; /* external TRAM pages and size */ unsigned int dbg; /* FX debugger register */ diff --git a/sound/pci/emu10k1/emu10k1_main.c b/sound/pci/emu10k1/emu10k1_main.c index 3880f359e688..65fd6b62bc9c 100644 --- a/sound/pci/emu10k1/emu10k1_main.c +++ b/sound/pci/emu10k1/emu10k1_main.c @@ -1901,11 +1901,12 @@ int snd_emu10k1_create(struct snd_card *card, pci_set_master(pci); - emu->fx8010.fxbus_mask = 0x303f; + // The masks are not used for Audigy. + // FIXME: these should come from the card_capabilites table. if (extin_mask == 0) - extin_mask = 0x3fcf; + extin_mask = 0x3fcf; // EXTIN_* if (extout_mask == 0) - extout_mask = 0x7fff; + extout_mask = 0x7fff; // EXTOUT_* emu->fx8010.extin_mask = extin_mask; emu->fx8010.extout_mask = extout_mask; emu->enable_ir = enable_ir; diff --git a/sound/pci/emu10k1/emufx.c b/sound/pci/emu10k1/emufx.c index 6cf7c8b1de47..c74e66e03ae0 100644 --- a/sound/pci/emu10k1/emufx.c +++ b/sound/pci/emu10k1/emufx.c @@ -2523,19 +2523,18 @@ static void snd_emu10k1_fx8010_info(struct snd_emu10k1 *emu, struct snd_emu10k1_fx8010_info *info) { const char * const *fxbus, * const *extin, * const *extout; - unsigned short fxbus_mask, extin_mask, extout_mask; + unsigned short extin_mask, extout_mask; int res; info->internal_tram_size = emu->fx8010.itram_size; info->external_tram_size = emu->fx8010.etram_pages.bytes / 2; fxbus = fxbuses; extin = emu->audigy ? audigy_ins : creative_ins; extout = emu->audigy ? audigy_outs : creative_outs; - fxbus_mask = emu->fx8010.fxbus_mask; - extin_mask = emu->fx8010.extin_mask; - extout_mask = emu->fx8010.extout_mask; + extin_mask = emu->audigy ? ~0 : emu->fx8010.extin_mask; + extout_mask = emu->audigy ? ~0 : emu->fx8010.extout_mask; for (res = 0; res < 16; res++, fxbus++, extin++, extout++) { - copy_string(info->fxbus_names[res], fxbus_mask & (1 << res) ? *fxbus : NULL, "FXBUS", res); + copy_string(info->fxbus_names[res], *fxbus, "FXBUS", res); copy_string(info->extin_names[res], extin_mask & (1 << res) ? *extin : NULL, "Unused", res); copy_string(info->extout_names[res], extout_mask & (1 << res) ? *extout : NULL, "Unused", res); } -- 2.40.0.152.g15d061e6df

2 1

[PATCH v3] docs: sound/kernel-api/writing-an-alsa-driver.rst: polishing
by Oswald Buddenhagen 21 Apr '23

21 Apr '23

- Update some outdated info - Language fixes - Whitespace/formatting fixes - Prefer attached over stand-alone '::' Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- v3: - fixed one fixme and dropped another one (these were actually meant to go into the RFC patch ...) v2: - dropped questionable hunk from period timer example code - new hunk: improved wording wrt period sizes --- .../kernel-api/writing-an-alsa-driver.rst | 1051 +++++++---------- 1 file changed, 398 insertions(+), 653 deletions(-) diff --git a/Documentation/sound/kernel-api/writing-an-alsa-driver.rst b/Documentation/sound/kernel-api/writing-an-alsa-driver.rst index a368529e8ed3..93fae4dad19c 100644 --- a/Documentation/sound/kernel-api/writing-an-alsa-driver.rst +++ b/Documentation/sound/kernel-api/writing-an-alsa-driver.rst @@ -19,18 +19,13 @@ explain the general topic of linux kernel coding and doesn't cover low-level driver implementation details. It only describes the standard way to write a PCI sound driver on ALSA. -This document is still a draft version. Any feedback and corrections, -please!! - File Tree Structure =================== General ------- -The file tree structure of ALSA driver is depicted below. - -:: +The file tree structure of ALSA driver is depicted below:: sound /core @@ -68,39 +63,39 @@ kernel config. core/oss ~~~~~~~~ -The codes for PCM and mixer OSS emulation modules are stored in this -directory. The rawmidi OSS emulation is included in the ALSA rawmidi +The code for OSS PCM and mixer emulation modules is stored in this +directory. The OSS rawmidi emulation is included in the ALSA rawmidi code since it's quite small. The sequencer code is stored in ``core/seq/oss`` directory (see `below <core/seq/oss_>`__). core/seq ~~~~~~~~ This directory and its sub-directories are for the ALSA sequencer. This directory contains the sequencer core and primary sequencer modules such -like snd-seq-midi, snd-seq-virmidi, etc. They are compiled only when +as snd-seq-midi, snd-seq-virmidi, etc. They are compiled only when ``CONFIG_SND_SEQUENCER`` is set in the kernel config. core/seq/oss ~~~~~~~~~~~~ -This contains the OSS sequencer emulation codes. +This contains the OSS sequencer emulation code. include directory ----------------- This is the place for the public header files of ALSA drivers, which are -to be exported to user-space, or included by several files at different +to be exported to user-space, or included by several files in different directories. Basically, the private header files should not be placed in this directory, but you may still find files there, due to historical reasons :) drivers directory ----------------- This directory contains code shared among different drivers on different architectures. They are hence supposed not to be architecture-specific. -For example, the dummy pcm driver and the serial MIDI driver are found +For example, the dummy PCM driver and the serial MIDI driver are found in this directory. In the sub-directories, there is code for components which are independent from bus and cpu architectures. @@ -156,8 +151,8 @@ these architectures. usb directory ------------- -This directory contains the USB-audio driver. In the latest version, the -USB MIDI driver is integrated in the usb-audio driver. +This directory contains the USB-audio driver. +The USB MIDI driver is integrated in the usb-audio driver. pcmcia directory ---------------- @@ -175,9 +170,9 @@ layer including ASoC core, codec and machine drivers. oss directory ------------- -Here contains OSS/Lite codes. -All codes have been deprecated except for dmasound on m68k as of -writing this. +This contains OSS/Lite code. +At the time of writing, all code has been removed except for dmasound +on m68k. Basic Flow for PCI Drivers @@ -341,7 +336,7 @@ to details explained in the following section. error: snd_card_free(card); - return err; + return err; } /* destructor -- see the "Destructor" sub-section */ @@ -381,7 +376,7 @@ where ``enable[dev]`` is the module option. Each time the ``probe`` callback is called, check the availability of the device. If not available, simply increment the device index and -returns. dev will be incremented also later (`step 7 +return. dev will be incremented also later (`step 7 <7) Set the PCI driver data and return zero._>`__). 2) Create a card instance @@ -402,9 +397,7 @@ Components`_. 3) Create a main component ~~~~~~~~~~~~~~~~~~~~~~~~~~ -In this part, the PCI resources are allocated. - -:: +In this part, the PCI resources are allocated:: struct mychip *chip; .... @@ -417,13 +410,11 @@ Management`_. When something goes wrong, the probe function needs to deal with the error. In this example, we have a single error handling path placed -at the end of the function. - -:: +at the end of the function:: error: snd_card_free(card); - return err; + return err; Since each component can be properly freed, the single :c:func:`snd_card_free()` call should suffice in most cases. @@ -483,13 +474,11 @@ remove callback and power-management callbacks, too. Destructor ---------- -The destructor, remove callback, simply releases the card instance. Then -the ALSA middle layer will release all the attached components +The destructor, the remove callback, simply releases the card instance. +Then the ALSA middle layer will release all the attached components automatically. -It would be typically just calling :c:func:`snd_card_free()`: - -:: +It would be typically just calling :c:func:`snd_card_free()`:: static void snd_mychip_remove(struct pci_dev *pci) { @@ -504,9 +493,7 @@ Header Files ------------ For the above example, at least the following include files are -necessary. - -:: +necessary:: #include <linux/init.h> #include <linux/pci.h> @@ -544,9 +531,7 @@ list on the card record is used to manage the correct release of resources at destruction. As mentioned above, to create a card instance, call -:c:func:`snd_card_new()`. - -:: +:c:func:`snd_card_new()`:: struct snd_card *card; int err; @@ -572,10 +557,8 @@ struct snd_device object. A component can be a PCM instance, a control interface, a raw MIDI interface, etc. Each such instance has one component entry. -A component can be created via :c:func:`snd_device_new()` -function. - -:: +A component can be created via the :c:func:`snd_device_new()` +function:: snd_device_new(card, SNDRV_DEV_XXX, chip, &ops); @@ -591,7 +574,7 @@ allocated manually beforehand, and its pointer is passed as the argument. This pointer (``chip`` in the above example) is used as the identifier for the instance. -Each pre-defined ALSA component such as ac97 and pcm calls +Each pre-defined ALSA component such as AC97 and PCM calls :c:func:`snd_device_new()` inside its constructor. The destructor for each component is defined in the callback pointers. Hence, you don't need to take care of calling a destructor for such a component. @@ -605,9 +588,7 @@ Chip-Specific Data ------------------ Chip-specific information, e.g. the I/O port address, its resource -pointer, or the irq number, is stored in the chip-specific record. - -:: +pointer, or the irq number, is stored in the chip-specific record:: struct mychip { .... @@ -620,9 +601,7 @@ In general, there are two ways of allocating the chip record. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ As mentioned above, you can pass the extra-data-length to the 5th -argument of :c:func:`snd_card_new()`, i.e. - -:: +argument of :c:func:`snd_card_new()`, e.g.:: err = snd_card_new(&pci->dev, index[dev], id[dev], THIS_MODULE, sizeof(struct mychip), &card); @@ -642,9 +621,7 @@ released together with the card instance. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ After allocating a card instance via :c:func:`snd_card_new()` -(with ``0`` on the 4th arg), call :c:func:`kzalloc()`. - -:: +(with ``0`` on the 4th arg), call :c:func:`kzalloc()`:: struct snd_card *card; struct mychip *chip; @@ -663,39 +640,33 @@ The chip record should have the field to hold the card pointer at least, }; -Then, set the card pointer in the returned chip instance. - -:: +Then, set the card pointer in the returned chip instance:: chip->card = card; Next, initialize the fields, and register this chip record as a -low-level device with a specified ``ops``, - -:: +low-level device with a specified ``ops``:: static const struct snd_device_ops ops = { .dev_free = snd_mychip_dev_free, }; .... snd_device_new(card, SNDRV_DEV_LOWLEVEL, chip, &ops); :c:func:`snd_mychip_dev_free()` is the device-destructor -function, which will call the real destructor. - -:: +function, which will call the real destructor:: static int snd_mychip_dev_free(struct snd_device *device) { return snd_mychip_free(device->device_data); } where :c:func:`snd_mychip_free()` is the real destructor. -The demerit of this method is the obviously more amount of codes. -The merit is, however, you can trigger the own callback at registering -and disconnecting the card via setting in snd_device_ops. -About the registering and disconnecting the card, see the subsections +The demerit of this method is the obviously larger amount of code. +The merit is, however, that you can trigger your own callback at +registering and disconnecting the card via a setting in snd_device_ops. +About registering and disconnecting the card, see the subsections below. @@ -724,9 +695,7 @@ Full Code Example ----------------- In this section, we'll complete the chip-specific constructor, -destructor and PCI entries. Example code is shown first, below. - -:: +destructor and PCI entries. Example code is shown first, below:: struct mychip { struct snd_card *card; @@ -866,9 +835,7 @@ resources. Also, you need to set the proper PCI DMA mask to limit the accessed I/O range. In some cases, you might need to call :c:func:`pci_set_master()` function, too. -Suppose the 28bit mask, and the code to be added would be like: - -:: +Suppose a 28bit mask, the code to be added would look like:: err = pci_enable_device(pci); if (err < 0) @@ -890,9 +857,7 @@ function (see below). Now assume that the PCI device has an I/O port with 8 bytes and an interrupt. Then struct mychip will have the -following fields: - -:: +following fields:: struct mychip { struct snd_card *card; @@ -905,14 +870,12 @@ following fields: For an I/O port (and also a memory region), you need to have the resource pointer for the standard resource management. For an irq, you have to keep only the irq number (integer). But you need to initialize -this number as -1 before actual allocation, since irq 0 is valid. The +this number to -1 before actual allocation, since irq 0 is valid. The port address and its resource pointer can be initialized as null by :c:func:`kzalloc()` automatically, so you don't have to take care of resetting them. -The allocation of an I/O port is done like this: - -:: +The allocation of an I/O port is done like this:: err = pci_request_regions(pci, "My Chip"); if (err < 0) { @@ -928,9 +891,7 @@ The returned value, ``chip->res_port``, is allocated via must be released via :c:func:`kfree()`, but there is a problem with this. This issue will be explained later. -The allocation of an interrupt source is done like this: - -:: +The allocation of an interrupt source is done like this:: if (request_irq(pci->irq, snd_mychip_interrupt, IRQF_SHARED, KBUILD_MODNAME, chip)) { @@ -954,36 +915,31 @@ used for that, but you can use what you like, too. I won't give details about the interrupt handler at this point, but at least its appearance can be explained now. The interrupt handler looks -usually like the following: - -:: +usually as follows:: static irqreturn_t snd_mychip_interrupt(int irq, void *dev_id) { struct mychip *chip = dev_id; .... return IRQ_HANDLED; } After requesting the IRQ, you can passed it to ``card->sync_irq`` -field: -:: +field:: card->irq = chip->irq; -This allows PCM core automatically performing -:c:func:`synchronize_irq()` at the necessary timing like ``hw_free``. +This allows the PCM core to automatically call +:c:func:`synchronize_irq()` at the right time, like before ``hw_free``. See the later section `sync_stop callback`_ for details. Now let's write the corresponding destructor for the resources above. The role of destructor is simple: disable the hardware (if already activated) and release the resources. So far, we have no hardware part, so the disabling code is not written here. To release the resources, the “check-and-release” method is a safer way. -For the interrupt, do like this: - -:: +For the interrupt, do like this:: if (chip->irq >= 0) free_irq(chip->irq, chip); @@ -997,72 +953,59 @@ When you requested I/O ports or memory regions via :c:func:`pci_request_regions()` like in this example, release the resource(s) using the corresponding function, :c:func:`pci_release_region()` or -:c:func:`pci_release_regions()`. - -:: +:c:func:`pci_release_regions()`:: pci_release_regions(chip->pci); When you requested manually via :c:func:`request_region()` or :c:func:`request_mem_region()`, you can release it via :c:func:`release_resource()`. Suppose that you keep the resource pointer returned from :c:func:`request_region()` in -chip->res_port, the release procedure looks like: - -:: +chip->res_port, the release procedure looks like:: release_and_free_resource(chip->res_port); Don't forget to call :c:func:`pci_disable_device()` before the end. -And finally, release the chip-specific record. - -:: +And finally, release the chip-specific record:: kfree(chip); -We didn't implement the hardware disabling part in the above. If you +We didn't implement the hardware disabling part above. If you need to do this, please note that the destructor may be called even before the initialization of the chip is completed. It would be better to have a flag to skip hardware disabling if the hardware was not initialized yet. When the chip-data is assigned to the card using -:c:func:`snd_device_new()` with ``SNDRV_DEV_LOWLELVEL`` , its -destructor is called at the last. That is, it is assured that all other +:c:func:`snd_device_new()` with ``SNDRV_DEV_LOWLELVEL``, its +destructor is called last. That is, it is assured that all other components like PCMs and controls have already been released. You don't have to stop PCMs, etc. explicitly, but just call low-level hardware stopping. The management of a memory-mapped region is almost as same as the -management of an I/O port. You'll need three fields like the -following: - -:: +management of an I/O port. You'll need two fields as follows:: struct mychip { .... unsigned long iobase_phys; void __iomem *iobase_virt; }; -and the allocation would be like below: - -:: +and the allocation would look like below:: err = pci_request_regions(pci, "My Chip"); if (err < 0) { kfree(chip); return err; } chip->iobase_phys = pci_resource_start(pci, 0); chip->iobase_virt = ioremap(chip->iobase_phys, pci_resource_len(pci, 0)); -and the corresponding destructor would be: - -:: +and the corresponding destructor would be:: static int snd_mychip_free(struct mychip *chip) { @@ -1075,9 +1018,7 @@ and the corresponding destructor would be: } Of course, a modern way with :c:func:`pci_iomap()` will make things a -bit easier, too. - -:: +bit easier, too:: err = pci_request_regions(pci, "My Chip"); if (err < 0) { @@ -1097,9 +1038,7 @@ struct pci_device_id table for this chipset. It's a table of PCI vendor/device ID number, and some masks. -For example, - -:: +For example:: static struct pci_device_id snd_mychip_ids[] = { { PCI_VENDOR_ID_FOO, PCI_DEVICE_ID_BAR, @@ -1120,24 +1059,20 @@ The last entry of this list is the terminator. You must specify this all-zero entry. Then, prepare the struct pci_driver -record: - -:: +record:: static struct pci_driver driver = { .name = KBUILD_MODNAME, .id_table = snd_mychip_ids, .probe = snd_mychip_probe, .remove = snd_mychip_remove, }; The ``probe`` and ``remove`` functions have already been defined in the previous sections. The ``name`` field is the name string of this -device. Note that you must not use a slash “/” in this string. +device. Note that you must not use slashes (“/”) in this string. -And at last, the module entries: - -:: +And at last, the module entries:: static int __init alsa_card_mychip_init(void) { @@ -1167,33 +1102,31 @@ The PCM middle layer of ALSA is quite powerful and it is only necessary for each driver to implement the low-level functions to access its hardware. -For accessing to the PCM layer, you need to include ``<sound/pcm.h>`` +To access the PCM layer, you need to include ``<sound/pcm.h>`` first. In addition, ``<sound/pcm_params.h>`` might be needed if you -access to some functions related with hw_param. +access some functions related with hw_param. -Each card device can have up to four pcm instances. A pcm instance -corresponds to a pcm device file. The limitation of number of instances -comes only from the available bit size of the Linux's device numbers. -Once when 64bit device number is used, we'll have more pcm instances +Each card device can have up to four PCM instances. A PCM instance +corresponds to a PCM device file. The limitation of number of instances +comes only from the available bit size of Linux' device numbers. +Once 64bit device numbers are used, we'll have more PCM instances available. -A pcm instance consists of pcm playback and capture streams, and each -pcm stream consists of one or more pcm substreams. Some soundcards +A PCM instance consists of PCM playback and capture streams, and each +PCM stream consists of one or more PCM substreams. Some soundcards support multiple playback functions. For example, emu10k1 has a PCM playback of 32 stereo substreams. In this case, at each open, a free substream is (usually) automatically chosen and opened. Meanwhile, when -only one substream exists and it was already opened, the successful open +only one substream exists and it was already opened, a subsequent open will either block or error with ``EAGAIN`` according to the file open mode. But you don't have to care about such details in your driver. The PCM middle layer will take care of such work. Full Code Example ----------------- The example code below does not include any hardware access routines but -shows only the skeleton, how to build up the PCM interfaces. - -:: +shows only the skeleton, how to build up the PCM interfaces:: #include <sound/pcm.h> .... @@ -1399,10 +1332,8 @@ shows only the skeleton, how to build up the PCM interfaces. PCM Constructor --------------- -A pcm instance is allocated by the :c:func:`snd_pcm_new()` -function. It would be better to create a constructor for pcm, namely, - -:: +A PCM instance is allocated by the :c:func:`snd_pcm_new()` +function. It would be better to create a constructor for the PCM, namely:: static int snd_mychip_new_pcm(struct mychip *chip) { @@ -1415,16 +1346,16 @@ function. It would be better to create a constructor for pcm, namely, pcm->private_data = chip; strcpy(pcm->name, "My Chip"); chip->pcm = pcm; - .... + ... return 0; } -The :c:func:`snd_pcm_new()` function takes four arguments. The -first argument is the card pointer to which this pcm is assigned, and +The :c:func:`snd_pcm_new()` function takes six arguments. The +first argument is the card pointer to which this PCM is assigned, and the second is the ID string. The third argument (``index``, 0 in the above) is the index of this new -pcm. It begins from zero. If you create more than one pcm instances, +PCM. It begins from zero. If you create more than one PCM instances, specify the different numbers in this argument. For example, ``index = 1`` for the second PCM device. @@ -1437,26 +1368,20 @@ If a chip supports multiple playbacks or captures, you can specify more numbers, but they must be handled properly in open/close, etc. callbacks. When you need to know which substream you are referring to, then it can be obtained from struct snd_pcm_substream data passed to each -callback as follows: - -:: +callback as follows:: struct snd_pcm_substream *substream; int index = substream->number; -After the pcm is created, you need to set operators for each pcm stream. - -:: +After the PCM is created, you need to set operators for each PCM stream:: snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_PLAYBACK, &snd_mychip_playback_ops); snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_CAPTURE, &snd_mychip_capture_ops); -The operators are defined typically like this: - -:: +The operators are defined typically like this:: static struct snd_pcm_ops snd_mychip_playback_ops = { .open = snd_mychip_pcm_open, @@ -1472,41 +1397,35 @@ All the callbacks are described in the Operators_ subsection. After setting the operators, you probably will want to pre-allocate the buffer and set up the managed allocation mode. -For that, simply call the following: - -:: +For that, simply call the following:: snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_DEV, &chip->pci->dev, 64*1024, 64*1024); -It will allocate a buffer up to 64kB as default. Buffer management +It will allocate a buffer up to 64kB by default. Buffer management details will be described in the later section `Buffer and Memory Management`_. -Additionally, you can set some extra information for this pcm in +Additionally, you can set some extra information for this PCM in ``pcm->info_flags``. The available values are defined as ``SNDRV_PCM_INFO_XXX`` in ``<sound/asound.h>``, which is used for the hardware definition (described later). When your soundchip supports only -half-duplex, specify like this: - -:: +half-duplex, specify it like this:: pcm->info_flags = SNDRV_PCM_INFO_HALF_DUPLEX; ... And the Destructor? ----------------------- -The destructor for a pcm instance is not always necessary. Since the pcm +The destructor for a PCM instance is not always necessary. Since the PCM device will be released by the middle layer code automatically, you don't have to call the destructor explicitly. The destructor would be necessary if you created special records internally and needed to release them. In such a case, set the -destructor function to ``pcm->private_free``: - -:: +destructor function to ``pcm->private_free``:: static void mychip_pcm_free(struct snd_pcm *pcm) { @@ -1537,13 +1456,11 @@ Runtime Pointer - The Chest of PCM Information When the PCM substream is opened, a PCM runtime instance is allocated and assigned to the substream. This pointer is accessible via ``substream->runtime``. This runtime pointer holds most information you -need to control the PCM: the copy of hw_params and sw_params +need to control the PCM: a copy of hw_params and sw_params configurations, the buffer pointers, mmap records, spinlocks, etc. The definition of runtime instance is found in ``<sound/pcm.h>``. Here -are the contents of this file: - -:: +is the relevant part of this file:: struct _snd_pcm_runtime { /* -- Status -- */ @@ -1638,24 +1555,20 @@ Hardware Description The hardware descriptor (struct snd_pcm_hardware) contains the definitions of the fundamental hardware configuration. Above all, you'll need to define this -in the `PCM open callback`_. Note that the runtime instance holds the copy of -the descriptor, not the pointer to the existing descriptor. That is, +in the `PCM open callback`_. Note that the runtime instance holds a copy of +the descriptor, not a pointer to the existing descriptor. That is, in the open callback, you can modify the copied descriptor (``runtime->hw``) as you need. For example, if the maximum number of channels is 1 only on some chip models, you can still use the same -hardware descriptor and change the channels_max later: - -:: +hardware descriptor and change the channels_max later:: struct snd_pcm_runtime *runtime = substream->runtime; ... runtime->hw = snd_mychip_playback_hw; /* common definition */ if (chip->model == VERY_OLD_ONE) runtime->hw.channels_max = 1; -Typically, you'll have a hardware descriptor as below: - -:: +Typically, you'll have a hardware descriptor as below:: static struct snd_pcm_hardware snd_mychip_playback_hw = { .info = (SNDRV_PCM_INFO_MMAP | @@ -1676,71 +1589,72 @@ Typically, you'll have a hardware descriptor as below: }; - The ``info`` field contains the type and capabilities of this - pcm. The bit flags are defined in ``<sound/asound.h>`` as + PCM. The bit flags are defined in ``<sound/asound.h>`` as ``SNDRV_PCM_INFO_XXX``. Here, at least, you have to specify whether - the mmap is supported and which interleaved format is + mmap is supported and which interleaving formats are supported. When the hardware supports mmap, add the ``SNDRV_PCM_INFO_MMAP`` flag here. When the hardware supports the - interleaved or the non-interleaved formats, + interleaved or the non-interleaved formats, the ``SNDRV_PCM_INFO_INTERLEAVED`` or ``SNDRV_PCM_INFO_NONINTERLEAVED`` flag must be set, respectively. If both are supported, you can set both, too. In the above example, ``MMAP_VALID`` and ``BLOCK_TRANSFER`` are specified for the OSS mmap mode. Usually both are set. Of course, - ``MMAP_VALID`` is set only if the mmap is really supported. + ``MMAP_VALID`` is set only if mmap is really supported. The other possible flags are ``SNDRV_PCM_INFO_PAUSE`` and - ``SNDRV_PCM_INFO_RESUME``. The ``PAUSE`` bit means that the pcm + ``SNDRV_PCM_INFO_RESUME``. The ``PAUSE`` bit means that the PCM supports the “pause” operation, while the ``RESUME`` bit means that - the pcm supports the full “suspend/resume” operation. If the + the PCM supports the full “suspend/resume” operation. If the ``PAUSE`` flag is set, the ``trigger`` callback below must handle the corresponding (pause push/release) commands. The suspend/resume trigger commands can be defined even without the ``RESUME`` - flag. See `Power Management`_ section for details. + flag. See the `Power Management`_ section for details. When the PCM substreams can be synchronized (typically, - synchronized start/stop of a playback and a capture streams), you + synchronized start/stop of a playback and a capture stream), you can give ``SNDRV_PCM_INFO_SYNC_START``, too. In this case, you'll need to check the linked-list of PCM substreams in the trigger - callback. This will be described in the later section. + callback. This will be described in a later section. -- ``formats`` field contains the bit-flags of supported formats +- The ``formats`` field contains the bit-flags of supported formats (``SNDRV_PCM_FMTBIT_XXX``). If the hardware supports more than one format, give all or'ed bits. In the example above, the signed 16bit little-endian format is specified. -- ``rates`` field contains the bit-flags of supported rates +- The ``rates`` field contains the bit-flags of supported rates (``SNDRV_PCM_RATE_XXX``). When the chip supports continuous rates, - pass ``CONTINUOUS`` bit additionally. The pre-defined rate bits are - provided only for typical rates. If your chip supports + pass the ``CONTINUOUS`` bit additionally. The pre-defined rate bits + are provided only for typical rates. If your chip supports unconventional rates, you need to add the ``KNOT`` bit and set up the hardware constraint manually (explained later). - ``rate_min`` and ``rate_max`` define the minimum and maximum sample rate. This should correspond somehow to ``rates`` bits. -- ``channels_min`` and ``channels_max`` define, as you might already +- ``channels_min`` and ``channels_max`` define, as you might have already expected, the minimum and maximum number of channels. - ``buffer_bytes_max`` defines the maximum buffer size in bytes. There is no ``buffer_bytes_min`` field, since it can be calculated from the minimum period size and the minimum number of periods. Meanwhile, ``period_bytes_min`` and ``period_bytes_max`` define the minimum and maximum size of the period in bytes. ``periods_max`` and ``periods_min`` define the maximum and minimum number of periods in the buffer. The “period” is a term that corresponds to a fragment in the OSS - world. The period defines the size at which a PCM interrupt is - generated. This size strongly depends on the hardware. Generally, - the smaller period size will give you more interrupts, that is, - more controls. In the case of capture, this size defines the input - latency. On the other hand, the whole buffer size defines the - output latency for the playback direction. + world. The period defines the point at which a PCM interrupt is + generated. This point strongly depends on the hardware. Generally, + a smaller period size will give you more interrupts, which results + in being able to fill/drain the buffer more timely. In the case of + capture, this size defines the input latency. On the other hand, + the whole buffer size defines the output latency for the playback + direction. - There is also a field ``fifo_size``. This specifies the size of the - hardware FIFO, but currently it is neither used in the driver nor + hardware FIFO, but currently it is neither used by the drivers nor in the alsa-lib. So, you can ignore this field. PCM Configurations @@ -1759,63 +1673,60 @@ One thing to be noted is that the configured buffer and period sizes are stored in “frames” in the runtime. In the ALSA world, ``1 frame = channels \* samples-size``. For conversion between frames and bytes, you can use the :c:func:`frames_to_bytes()` and -:c:func:`bytes_to_frames()` helper functions. - -:: +:c:func:`bytes_to_frames()` helper functions:: period_bytes = frames_to_bytes(runtime, runtime->period_size); Also, many software parameters (sw_params) are stored in frames, too. -Please check the type of the field. ``snd_pcm_uframes_t`` is for the -frames as unsigned integer while ``snd_pcm_sframes_t`` is for the +Please check the type of the field. ``snd_pcm_uframes_t`` is for +frames as unsigned integer while ``snd_pcm_sframes_t`` is for frames as signed integer. DMA Buffer Information ~~~~~~~~~~~~~~~~~~~~~~ -The DMA buffer is defined by the following four fields, ``dma_area``, -``dma_addr``, ``dma_bytes`` and ``dma_private``. The ``dma_area`` +The DMA buffer is defined by the following four fields: ``dma_area``, +``dma_addr``, ``dma_bytes`` and ``dma_private``. ``dma_area`` holds the buffer pointer (the logical address). You can call :c:func:`memcpy()` from/to this pointer. Meanwhile, ``dma_addr`` holds the physical address of the buffer. This field is specified only when -the buffer is a linear buffer. ``dma_bytes`` holds the size of buffer -in bytes. ``dma_private`` is used for the ALSA DMA allocator. +the buffer is a linear buffer. ``dma_bytes`` holds the size of the +buffer in bytes. ``dma_private`` is used for the ALSA DMA allocator. If you use either the managed buffer allocation mode or the standard API function :c:func:`snd_pcm_lib_malloc_pages()` for allocating the buffer, these fields are set by the ALSA middle layer, and you should *not* change them by yourself. You can read them but not write them. On the other hand, if you want to allocate the buffer by yourself, you'll -need to manage it in hw_params callback. At least, ``dma_bytes`` is +need to manage it in the hw_params callback. At least, ``dma_bytes`` is mandatory. ``dma_area`` is necessary when the buffer is mmapped. If your driver doesn't support mmap, this field is not necessary. ``dma_addr`` is also optional. You can use dma_private as you like, too. Running Status ~~~~~~~~~~~~~~ The running status can be referred via ``runtime->status``. This is -the pointer to the struct snd_pcm_mmap_status record. +a pointer to a struct snd_pcm_mmap_status record. For example, you can get the current DMA hardware pointer via ``runtime->status->hw_ptr``. The DMA application pointer can be referred via ``runtime->control``, -which points to the struct snd_pcm_mmap_control record. -However, accessing directly to this value is not recommended. +which points to a struct snd_pcm_mmap_control record. +However, accessing this value directly is not recommended. Private Data ~~~~~~~~~~~~ You can allocate a record for the substream and store it in ``runtime->private_data``. Usually, this is done in the `PCM open callback`_. Don't mix this with ``pcm->private_data``. The ``pcm->private_data`` usually points to the chip instance assigned -statically at the creation of PCM, while the ``runtime->private_data`` -points to a dynamic data structure created at the PCM open -callback. - -:: +statically at creation time of the PCM device, while +``runtime->private_data`` +points to a dynamic data structure created in the PCM open +callback:: static int snd_xxx_open(struct snd_pcm_substream *substream) { @@ -1832,20 +1743,18 @@ The allocated object must be released in the `close callback`_. Operators --------- -OK, now let me give details about each pcm callback (``ops``). In +OK, now let me give details about each PCM callback (``ops``). In general, every callback must return 0 if successful, or a negative error number such as ``-EINVAL``. To choose an appropriate error number, it is advised to check what value other parts of the kernel return when the same kind of request fails. -The callback function takes at least the argument with +Each callback function takes at least one argument containing a struct snd_pcm_substream pointer. To retrieve the chip record from the given substream instance, you can use the following -macro. +macro:: -:: - - int xxx() { + int xxx(...) { struct mychip *chip = snd_pcm_substream_chip(substream); .... } @@ -1864,12 +1773,10 @@ PCM open callback static int snd_xxx_open(struct snd_pcm_substream *substream); -This is called when a pcm substream is opened. +This is called when a PCM substream is opened. At least, here you have to initialize the ``runtime->hw`` -record. Typically, this is done by like this: - -:: +record. Typically, this is done like this:: static int snd_xxx_open(struct snd_pcm_substream *substream) { @@ -1883,7 +1790,7 @@ record. Typically, this is done by like this: where ``snd_mychip_playback_hw`` is the pre-defined hardware description. -You can allocate a private data in this callback, as described in +You can allocate private data in this callback, as described in the `Private Data`_ section. If the hardware configuration needs more constraints, set the hardware @@ -1897,73 +1804,69 @@ close callback static int snd_xxx_close(struct snd_pcm_substream *substream); -Obviously, this is called when a pcm substream is closed. +Obviously, this is called when a PCM substream is closed. -Any private instance for a pcm substream allocated in the ``open`` -callback will be released here. - -:: +Any private instance for a PCM substream allocated in the ``open`` +callback will be released here:: static int snd_xxx_close(struct snd_pcm_substream *substream) { .... kfree(substream->runtime->private_data); .... } ioctl callback ~~~~~~~~~~~~~~ -This is used for any special call to pcm ioctls. But usually you can -leave it as NULL, then PCM core calls the generic ioctl callback -function :c:func:`snd_pcm_lib_ioctl()`. If you need to deal with the +This is used for any special call to PCM ioctls. But usually you can +leave it NULL, then the PCM core calls the generic ioctl callback +function :c:func:`snd_pcm_lib_ioctl()`. If you need to deal with a unique setup of channel info or reset procedure, you can pass your own callback function here. hw_params callback ~~~~~~~~~~~~~~~~~~~ :: static int snd_xxx_hw_params(struct snd_pcm_substream *substream, struct snd_pcm_hw_params *hw_params); -This is called when the hardware parameter (``hw_params``) is set up +This is called when the hardware parameters (``hw_params``) are set up by the application, that is, once when the buffer size, the period -size, the format, etc. are defined for the pcm substream. +size, the format, etc. are defined for the PCM substream. Many hardware setups should be done in this callback, including the allocation of buffers. -Parameters to be initialized are retrieved by +Parameters to be initialized are retrieved by the :c:func:`params_xxx()` macros. -When you set up the managed buffer allocation mode for the substream, +When you choose managed buffer allocation mode for the substream, a buffer is already allocated before this callback gets called. Alternatively, you can call a helper function below for -allocating the buffer, too. - -:: +allocating the buffer:: snd_pcm_lib_malloc_pages(substream, params_buffer_bytes(hw_params)); :c:func:`snd_pcm_lib_malloc_pages()` is available only when the DMA buffers have been pre-allocated. See the section `Buffer Types`_ for more details. -Note that this and ``prepare`` callbacks may be called multiple times -per initialization. For example, the OSS emulation may call these +Note that this one and the ``prepare`` callback may be called multiple +times per initialization. For example, the OSS emulation may call these callbacks at each change via its ioctl. Thus, you need to be careful not to allocate the same buffers many times, which will lead to memory leaks! Calling the helper function above many times is OK. It will release the previous buffer automatically when it was already allocated. -Another note is that this callback is non-atomic (schedulable) as +Another note is that this callback is non-atomic (schedulable) by default, i.e. when no ``nonatomic`` flag set. This is important, because the ``trigger`` callback is atomic (non-schedulable). That is, -mutexes or any schedule-related functions are not available in +mutexes or any schedule-related functions are not available in the ``trigger`` callback. Please see the subsection Atomicity_ for details. @@ -1979,33 +1882,31 @@ This is called to release the resources allocated via This function is always called before the close callback is called. Also, the callback may be called multiple times, too. Keep track -whether the resource was already released. +whether each resource was already released. -When you have set up the managed buffer allocation mode for the PCM +When you have chosen managed buffer allocation mode for the PCM substream, the allocated PCM buffer will be automatically released after this callback gets called. Otherwise you'll have to release the buffer manually. Typically, when the buffer was allocated from the pre-allocated pool, you can use the standard API function -:c:func:`snd_pcm_lib_malloc_pages()` like: - -:: +:c:func:`snd_pcm_lib_malloc_pages()` like:: snd_pcm_lib_free_pages(substream); prepare callback ~~~~~~~~~~~~~~~~ :: static int snd_xxx_prepare(struct snd_pcm_substream *substream); -This callback is called when the pcm is “prepared”. You can set the +This callback is called when the PCM is “prepared”. You can set the format type, sample rate, etc. here. The difference from ``hw_params`` is that the ``prepare`` callback will be called each time :c:func:`snd_pcm_prepare()` is called, i.e. when recovering after underruns, etc. -Note that this callback is now non-atomic. You can use +Note that this callback is non-atomic. You can use schedule-related functions safely in this callback. In this and the following callbacks, you can refer to the values via @@ -2026,13 +1927,11 @@ trigger callback static int snd_xxx_trigger(struct snd_pcm_substream *substream, int cmd); -This is called when the pcm is started, stopped or paused. +This is called when the PCM is started, stopped or paused. -Which action is specified in the second argument, -``SNDRV_PCM_TRIGGER_XXX`` in ``<sound/pcm.h>``. At least, the ``START`` -and ``STOP`` commands must be defined in this callback. - -:: +The action is specified in the second argument, ``SNDRV_PCM_TRIGGER_XXX`` +defined in ``<sound/pcm.h>``. At least, the ``START`` +and ``STOP`` commands must be defined in this callback:: switch (cmd) { case SNDRV_PCM_TRIGGER_START: @@ -2045,49 +1944,49 @@ and ``STOP`` commands must be defined in this callback. return -EINVAL; } -When the pcm supports the pause operation (given in the info field of +When the PCM supports the pause operation (given in the info field of the hardware table), the ``PAUSE_PUSH`` and ``PAUSE_RELEASE`` commands -must be handled here, too. The former is the command to pause the pcm, -and the latter to restart the pcm again. +must be handled here, too. The former is the command to pause the PCM, +and the latter to restart the PCM again. -When the pcm supports the suspend/resume operation, regardless of full +When the PCM supports the suspend/resume operation, regardless of full or partial suspend/resume support, the ``SUSPEND`` and ``RESUME`` commands must be handled, too. These commands are issued when the power-management status is changed. Obviously, the ``SUSPEND`` and -``RESUME`` commands suspend and resume the pcm substream, and usually, +``RESUME`` commands suspend and resume the PCM substream, and usually, they are identical to the ``STOP`` and ``START`` commands, respectively. See the `Power Management`_ section for details. -As mentioned, this callback is atomic as default unless ``nonatomic`` +As mentioned, this callback is atomic by default unless the ``nonatomic`` flag set, and you cannot call functions which may sleep. The ``trigger`` callback should be as minimal as possible, just really -triggering the DMA. The other stuff should be initialized +triggering the DMA. The other stuff should be initialized in ``hw_params`` and ``prepare`` callbacks properly beforehand. sync_stop callback ~~~~~~~~~~~~~~~~~~ :: static int snd_xxx_sync_stop(struct snd_pcm_substream *substream); This callback is optional, and NULL can be passed. It's called after -the PCM core stops the stream and changes the stream state +the PCM core stops the stream, before it changes the stream state via ``prepare``, ``hw_params`` or ``hw_free``. Since the IRQ handler might be still pending, we need to wait until the pending task finishes before moving to the next step; otherwise it -might lead to a crash due to resource conflicts or access to the freed +might lead to a crash due to resource conflicts or access to freed resources. A typical behavior is to call a synchronization function like :c:func:`synchronize_irq()` here. -For majority of drivers that need only a call of +For the majority of drivers that need only a call of :c:func:`synchronize_irq()`, there is a simpler setup, too. -While keeping NULL to ``sync_stop`` PCM callback, the driver can set -``card->sync_irq`` field to store the valid interrupt number after -requesting an IRQ, instead. Then PCM core will look call +While keeping the ``sync_stop`` PCM callback NULL, the driver can set +the ``card->sync_irq`` field to the returned interrupt number after +requesting an IRQ, instead. Then PCM core will call :c:func:`synchronize_irq()` with the given IRQ appropriately. -If the IRQ handler is released at the card destructor, you don't need +If the IRQ handler is released by the card destructor, you don't need to clear ``card->sync_irq``, as the card itself is being released. So, usually you'll need to add just a single line for assigning ``card->sync_irq`` in the driver code unless the driver re-acquires @@ -2103,76 +2002,76 @@ pointer callback static snd_pcm_uframes_t snd_xxx_pointer(struct snd_pcm_substream *substream) This callback is called when the PCM middle layer inquires the current -hardware position on the buffer. The position must be returned in +hardware position in the buffer. The position must be returned in frames, ranging from 0 to ``buffer_size - 1``. -This is called usually from the buffer-update routine in the pcm +This is usually called from the buffer-update routine in the PCM middle layer, which is invoked when :c:func:`snd_pcm_period_elapsed()` -is called in the interrupt routine. Then the pcm middle layer updates +is called by the interrupt routine. Then the PCM middle layer updates the position and calculates the available space, and wakes up the sleeping poll threads, etc. -This callback is also atomic as default. +This callback is also atomic by default. copy_user, copy_kernel and fill_silence ops ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ These callbacks are not mandatory, and can be omitted in most cases. These callbacks are used when the hardware buffer cannot be in the -normal memory space. Some chips have their own buffer on the hardware +normal memory space. Some chips have their own buffer in the hardware which is not mappable. In such a case, you have to transfer the data manually from the memory buffer to the hardware buffer. Or, if the buffer is non-contiguous on both physical and virtual memory spaces, these callbacks must be defined, too. If these two callbacks are defined, copy and set-silence operations -are done by them. The detailed will be described in the later section +are done by them. The details will be described in the later section `Buffer and Memory Management`_. ack callback ~~~~~~~~~~~~ This callback is also not mandatory. This callback is called when the ``appl_ptr`` is updated in read or write operations. Some drivers like emu10k1-fx and cs46xx need to track the current ``appl_ptr`` for the internal buffer, and this callback is useful only for such a purpose. The callback function may return 0 or a negative error. When the -return value is ``-EPIPE``, PCM core treats as a buffer XRUN happens, +return value is ``-EPIPE``, PCM core treats that as a buffer XRUN, and changes the state to ``SNDRV_PCM_STATE_XRUN`` automatically. -This callback is atomic as default. +This callback is atomic by default. page callback ~~~~~~~~~~~~~ This callback is optional too. The mmap calls this callback to get the page fault address. -Since the recent changes, you need no special callback any longer for -the standard SG-buffer or vmalloc-buffer. Hence this callback should -be rarely used. +You need no special callback for the standard SG-buffer or vmalloc- +buffer. Hence this callback should be rarely used. -mmap calllback -~~~~~~~~~~~~~~ +mmap callback +~~~~~~~~~~~~~ This is another optional callback for controlling mmap behavior. -Once when defined, PCM core calls this callback when a page is -memory-mapped instead of dealing via the standard helper. +When defined, the PCM core calls this callback when a page is +memory-mapped, instead of using the standard helper. If you need special handling (due to some architecture or device-specific issues), implement everything here as you like. PCM Interrupt Handler --------------------- -The rest of pcm stuff is the PCM interrupt handler. The role of PCM +The remainder of the PCM stuff is the PCM interrupt handler. The role +of the PCM interrupt handler in the sound driver is to update the buffer position and to tell the PCM middle layer when the buffer position goes across -the prescribed period size. To inform this, call the +the specified period boundary. To inform about this, call the :c:func:`snd_pcm_period_elapsed()` function. -There are several types of sound chips to generate the interrupts. +There are several ways sound chips can generate interrupts. Interrupts at the period (fragment) boundary ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ @@ -2188,14 +2087,12 @@ chip record to hold the current running substream pointer, and set the pointer value at ``open`` callback (and reset at ``close`` callback). If you acquire a spinlock in the interrupt handler, and the lock is used -in other pcm callbacks, too, then you have to release the lock before +in other PCM callbacks, too, then you have to release the lock before calling :c:func:`snd_pcm_period_elapsed()`, because -:c:func:`snd_pcm_period_elapsed()` calls other pcm callbacks +:c:func:`snd_pcm_period_elapsed()` calls other PCM callbacks inside. -Typical code would be like: - -:: +Typical code would look like:: static irqreturn_t snd_mychip_interrupt(int irq, void *dev_id) @@ -2233,9 +2130,7 @@ position and accumulate the processed sample length at each interrupt. When the accumulated size exceeds the period size, call :c:func:`snd_pcm_period_elapsed()` and reset the accumulator. -Typical code would be like the following. - -:: +Typical code would look as follows:: static irqreturn_t snd_mychip_interrupt(int irq, void *dev_id) @@ -2280,25 +2175,25 @@ Typical code would be like the following. On calling :c:func:`snd_pcm_period_elapsed()` ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ -In both cases, even if more than one period are elapsed, you don't have +In both cases, even if more than one period has elapsed, you don't have to call :c:func:`snd_pcm_period_elapsed()` many times. Call only -once. And the pcm layer will check the current hardware pointer and +once. And the PCM layer will check the current hardware pointer and update to the latest status. Atomicity --------- One of the most important (and thus difficult to debug) problems in kernel programming are race conditions. In the Linux kernel, they are usually avoided via spin-locks, mutexes or semaphores. In general, if a race condition can happen in an interrupt handler, it has to be managed atomically, and you have to use a spinlock to protect the critical -session. If the critical section is not in interrupt handler code and if +section. If the critical section is not in interrupt handler code and if taking a relatively long time to execute is acceptable, you should use mutexes or semaphores instead. -As already seen, some pcm callbacks are atomic and some are not. For -example, the ``hw_params`` callback is non-atomic, while ``trigger`` +As already seen, some PCM callbacks are atomic and some are not. For +example, the ``hw_params`` callback is non-atomic, while the ``trigger`` callback is atomic. This means, the latter is called already in a spinlock held by the PCM middle layer, the PCM stream lock. Please take this atomicity into account when you choose a locking scheme in @@ -2313,13 +2208,13 @@ callback, please use :c:func:`udelay()` or :c:func:`mdelay()`. All three atomic callbacks (trigger, pointer, and ack) are called with local interrupts disabled. -The recent changes in PCM core code, however, allow all PCM operations -to be non-atomic. This assumes that the all caller sides are in +However, it is possible to request all PCM operations to be non-atomic. +This assumes that all call sites are in non-atomic contexts. For example, the function :c:func:`snd_pcm_period_elapsed()` is called typically from the interrupt handler. But, if you set up the driver to use a threaded interrupt handler, this call can be in non-atomic context, too. In such -a case, you can set ``nonatomic`` filed of struct snd_pcm object +a case, you can set the ``nonatomic`` field of the struct snd_pcm object after creating it. When this flag is set, mutex and rwsem are used internally in the PCM core instead of spin and rwlocks, so that you can call all PCM functions safely in a non-atomic @@ -2335,14 +2230,12 @@ too. Constraints ----------- -If your chip supports unconventional sample rates, or only the limited -samples, you need to set a constraint for the condition. +Due to physical limitations, hardware is not infinitely configurable. +These limitations are expressed by setting constraints. -For example, in order to restrict the sample rates in the some supported +For example, in order to restrict the sample rates to some supported values, use :c:func:`snd_pcm_hw_constraint_list()`. You need to -call this function in the open callback. - -:: +call this function in the open callback:: static unsigned int rates[] = {4000, 10000, 22050, 44100}; @@ -2364,16 +2257,12 @@ call this function in the open callback. .... } - - There are many different constraints. Look at ``sound/pcm.h`` for a complete list. You can even define your own constraint rules. For example, let's suppose my_chip can manage a substream of 1 channel if and only if the format is ``S16_LE``, otherwise it supports any format -specified in struct snd_pcm_hardware> (or in any other -constraint_list). You can build a rule like this: - -:: +specified in struct snd_pcm_hardware (or in any other +constraint_list). You can build a rule like this:: static int hw_rule_channels_by_format(struct snd_pcm_hw_params *params, struct snd_pcm_hw_rule *rule) @@ -2393,20 +2282,16 @@ constraint_list). You can build a rule like this: } -Then you need to call this function to add your rule: - -:: +Then you need to call this function to add your rule:: snd_pcm_hw_rule_add(substream->runtime, 0, SNDRV_PCM_HW_PARAM_CHANNELS, hw_rule_channels_by_format, NULL, SNDRV_PCM_HW_PARAM_FORMAT, -1); The rule function is called when an application sets the PCM format, and it refines the number of channels accordingly. But an application may set the number of channels before setting the format. Thus you also need -to define the inverse rule: - -:: +to define the inverse rule:: static int hw_rule_format_by_channels(struct snd_pcm_hw_params *params, struct snd_pcm_hw_rule *rule) @@ -2425,34 +2310,30 @@ to define the inverse rule: } -... and in the open callback: - -:: +... and in the open callback:: snd_pcm_hw_rule_add(substream->runtime, 0, SNDRV_PCM_HW_PARAM_FORMAT, hw_rule_format_by_channels, NULL, SNDRV_PCM_HW_PARAM_CHANNELS, -1); One typical usage of the hw constraints is to align the buffer size -with the period size. As default, ALSA PCM core doesn't enforce the +with the period size. By default, ALSA PCM core doesn't enforce the buffer size to be aligned with the period size. For example, it'd be possible to have a combination like 256 period bytes with 999 buffer bytes. Many device chips, however, require the buffer to be a multiple of periods. In such a case, call :c:func:`snd_pcm_hw_constraint_integer()` for -``SNDRV_PCM_HW_PARAM_PERIODS``. - -:: +``SNDRV_PCM_HW_PARAM_PERIODS``:: snd_pcm_hw_constraint_integer(substream->runtime, SNDRV_PCM_HW_PARAM_PERIODS); This assures that the number of periods is integer, hence the buffer size is aligned with the period size. -The hw constraint is a very much powerful mechanism to define the +The hw constraint is a very powerful mechanism to define the preferred PCM configuration, and there are relevant helpers. I won't give more details here, rather I would like to say, “Luke, use the source.” @@ -2479,9 +2360,7 @@ Definition of Controls To create a new control, you need to define the following three callbacks: ``info``, ``get`` and ``put``. Then, define a -struct snd_kcontrol_new record, such as: - -:: +struct snd_kcontrol_new record, such as:: static struct snd_kcontrol_new my_control = { @@ -2524,7 +2403,7 @@ The ``private_value`` field contains an arbitrary long integer value for this record. When using the generic ``info``, ``get`` and ``put`` callbacks, you can pass a value through this field. If several small numbers are necessary, you can combine them in bitwise. Or, it's -possible to give a pointer (casted to unsigned long) of some record to +possible to store a pointer (casted to unsigned long) of some record in this field, too. The ``tlv`` field can be used to provide metadata about the control; @@ -2591,7 +2470,7 @@ The access flag is the bitmask which specifies the access type of the given control. The default access type is ``SNDRV_CTL_ELEM_ACCESS_READWRITE``, which means both read and write are allowed to this control. When the access flag is omitted (i.e. = 0), it -is considered as ``READWRITE`` access as default. +is considered as ``READWRITE`` access by default. When the control is read-only, pass ``SNDRV_CTL_ELEM_ACCESS_READ`` instead. In this case, you don't have to define the ``put`` callback. @@ -2604,21 +2483,22 @@ If the control value changes frequently (e.g. the VU meter), changed without `Change notification`_. Applications should poll such a control constantly. -When the control is inactive, set the ``INACTIVE`` flag, too. There are -``LOCK`` and ``OWNER`` flags to change the write permissions. +When the control may be updated, but currently has no effect on anything, +setting the ``INACTIVE`` flag may be appropriate. For example, PCM +controls should be inactive while no PCM device is open. + +There are ``LOCK`` and ``OWNER`` flags to change the write permissions. Control Callbacks ----------------- info callback ~~~~~~~~~~~~~ The ``info`` callback is used to get detailed information on this control. This must store the values of the given struct snd_ctl_elem_info object. For example, -for a boolean control with a single element: - -:: +for a boolean control with a single element:: static int snd_myctl_mono_info(struct snd_kcontrol *kcontrol, @@ -2637,13 +2517,11 @@ The ``type`` field specifies the type of the control. There are ``BOOLEAN``, ``INTEGER``, ``ENUMERATED``, ``BYTES``, ``IEC958`` and ``INTEGER64``. The ``count`` field specifies the number of elements in this control. For example, a stereo volume would have count = 2. The -``value`` field is a union, and the values stored are depending on the +``value`` field is a union, and the values stored depend on the type. The boolean and integer types are identical. -The enumerated type is a bit different from others. You'll need to set -the string for the currently given item index. - -:: +The enumerated type is a bit different from the others. You'll need to +set the string for the selectec item index:: static int snd_myctl_enum_info(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_info *uinfo) @@ -2688,13 +2566,10 @@ stereo channel boolean item. get callback ~~~~~~~~~~~~ -This callback is used to read the current value of the control and to -return to user-space. - -For example, - -:: +This callback is used to read the current value of the control, so it +can be returned to user-space. +For example:: static int snd_myctl_get(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol) @@ -2709,39 +2584,32 @@ For example, The ``value`` field depends on the type of control as well as on the info callback. For example, the sb driver uses this field to store the register offset, the bit-shift and the bit-mask. The ``private_value`` -field is set as follows: - -:: +field is set as follows:: .private_value = reg | (shift << 16) | (mask << 24) -and is retrieved in callbacks like - -:: +and is retrieved in callbacks like:: static int snd_sbmixer_get_single(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol) { int reg = kcontrol->private_value & 0xff; int shift = (kcontrol->private_value >> 16) & 0xff; int mask = (kcontrol->private_value >> 24) & 0xff; .... } In the ``get`` callback, you have to fill all the elements if the -control has more than one elements, i.e. ``count > 1``. In the example +control has more than one element, i.e. ``count > 1``. In the example above, we filled only one element (``value.integer.value[0]``) since -it's assumed as ``count = 1``. +``count = 1`` is assumed. put callback ~~~~~~~~~~~~ -This callback is used to write a value from user-space. - -For example, - -:: +This callback is used to write a value coming from user-space. +For example:: static int snd_myctl_put(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol) @@ -2764,23 +2632,21 @@ value is not changed, return 0 instead. If any fatal error happens, return a negative error code as usual. As in the ``get`` callback, when the control has more than one -elements, all elements must be evaluated in this callback, too. +element, all elements must be evaluated in this callback, too. Callbacks are not atomic ~~~~~~~~~~~~~~~~~~~~~~~~ -All these three callbacks are basically not atomic. +All these three callbacks are not-atomic. Control Constructor ------------------- When everything is ready, finally we can create a new control. To create a control, there are two functions to be called, :c:func:`snd_ctl_new1()` and :c:func:`snd_ctl_add()`. -In the simplest way, you can do like this: - -:: +In the simplest way, you can do it like this:: err = snd_ctl_add(card, snd_ctl_new1(&my_control, chip)); if (err < 0) @@ -2798,9 +2664,7 @@ Change Notification ------------------- If you need to change and update a control in the interrupt routine, you -can call :c:func:`snd_ctl_notify()`. For example, - -:: +can call :c:func:`snd_ctl_notify()`. For example:: snd_ctl_notify(card, SNDRV_CTL_EVENT_MASK_VALUE, id_pointer); @@ -2814,13 +2678,11 @@ for hardware volume interrupts. Metadata -------- -To provide information about the dB values of a mixer control, use on of +To provide information about the dB values of a mixer control, use one of the ``DECLARE_TLV_xxx`` macros from ``<sound/tlv.h>`` to define a variable containing this information, set the ``tlv.p`` field to point to this variable, and include the ``SNDRV_CTL_ELEM_ACCESS_TLV_READ`` flag -in the ``access`` field; like this: - -:: +in the ``access`` field; like this:: static DECLARE_TLV_DB_SCALE(db_scale_my_control, -4050, 150, 0); @@ -2910,24 +2772,20 @@ AC97 Constructor ---------------- To create an ac97 instance, first call :c:func:`snd_ac97_bus()` -with an ``ac97_bus_ops_t`` record with callback functions. - -:: +with an ``ac97_bus_ops_t`` record with callback functions:: struct snd_ac97_bus *bus; static struct snd_ac97_bus_ops ops = { .write = snd_mychip_ac97_write, .read = snd_mychip_ac97_read, }; snd_ac97_bus(card, 0, &ops, NULL, &pbus); The bus record is shared among all belonging ac97 instances. -And then call :c:func:`snd_ac97_mixer()` with an struct snd_ac97_template -record together with the bus pointer created above. - -:: +And then call :c:func:`snd_ac97_mixer()` with a struct snd_ac97_template +record together with the bus pointer created above:: struct snd_ac97_template ac97; int err; @@ -2952,9 +2810,7 @@ correspond to the functions for read and write accesses to the hardware low-level codes. The ``read`` callback returns the register value specified in the -argument. - -:: +argument:: static unsigned short snd_mychip_ac97_read(struct snd_ac97 *ac97, unsigned short reg) @@ -2967,9 +2823,7 @@ argument. Here, the chip can be cast from ``ac97->private_data``. Meanwhile, the ``write`` callback is used to set the register -value - -:: +value:: static void snd_mychip_ac97_write(struct snd_ac97 *ac97, unsigned short reg, unsigned short val) @@ -3002,32 +2856,24 @@ Both :c:func:`snd_ac97_write()` and the given register (``AC97_XXX``). The difference between them is that :c:func:`snd_ac97_update()` doesn't write a value if the given value has been already set, while :c:func:`snd_ac97_write()` -always rewrites the value. - -:: +always rewrites the value:: snd_ac97_write(ac97, AC97_MASTER, 0x8080); snd_ac97_update(ac97, AC97_MASTER, 0x8080); :c:func:`snd_ac97_read()` is used to read the value of the given -register. For example, - -:: +register. For example:: value = snd_ac97_read(ac97, AC97_MASTER); :c:func:`snd_ac97_update_bits()` is used to update some bits in -the given register. - -:: +the given register:: snd_ac97_update_bits(ac97, reg, mask, value); Also, there is a function to change the sample rate (of a given register such as ``AC97_PCM_FRONT_DAC_RATE``) when VRA or DRA is supported by the -codec: :c:func:`snd_ac97_set_rate()`. - -:: +codec: :c:func:`snd_ac97_set_rate()`:: snd_ac97_set_rate(ac97, AC97_PCM_FRONT_DAC_RATE, 44100); @@ -3082,9 +2928,7 @@ mpu401 stuff. For example, emu10k1 has its own mpu401 routines. MIDI Constructor ---------------- -To create a rawmidi object, call :c:func:`snd_mpu401_uart_new()`. - -:: +To create a rawmidi object, call :c:func:`snd_mpu401_uart_new()`:: struct snd_rawmidi *rmidi; snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401, port, info_flags, @@ -3129,16 +2973,12 @@ corresponds to the data port. If not, you may change the ``cport`` field of struct snd_mpu401 manually afterward. However, struct snd_mpu401 pointer is not returned explicitly by :c:func:`snd_mpu401_uart_new()`. You -need to cast ``rmidi->private_data`` to struct snd_mpu401 explicitly, - -:: +need to cast ``rmidi->private_data`` to struct snd_mpu401 explicitly:: struct snd_mpu401 *mpu; mpu = rmidi->private_data; -and reset the ``cport`` as you like: - -:: +and reset the ``cport`` as you like:: mpu->cport = my_own_control_port; @@ -3162,9 +3002,7 @@ occurred. In this case, you need to pass the private_data of the returned rawmidi object from :c:func:`snd_mpu401_uart_new()` as the second -argument of :c:func:`snd_mpu401_uart_interrupt()`. - -:: +argument of :c:func:`snd_mpu401_uart_interrupt()`:: snd_mpu401_uart_interrupt(irq, rmidi->private_data, regs); @@ -3188,9 +3026,7 @@ RawMIDI Constructor ------------------- To create a rawmidi device, call the :c:func:`snd_rawmidi_new()` -function: - -:: +function:: struct snd_rawmidi *rmidi; err = snd_rawmidi_new(chip->card, "MyMIDI", 0, outs, ins, &rmidi); @@ -3220,29 +3056,23 @@ output and input at the same time. After the rawmidi device is created, you need to set the operators (callbacks) for each substream. There are helper functions to set the -operators for all the substreams of a device: - -:: +operators for all the substreams of a device:: snd_rawmidi_set_ops(rmidi, SNDRV_RAWMIDI_STREAM_OUTPUT, &snd_mymidi_output_ops); snd_rawmidi_set_ops(rmidi, SNDRV_RAWMIDI_STREAM_INPUT, &snd_mymidi_input_ops); -The operators are usually defined like this: - -:: +The operators are usually defined like this:: static struct snd_rawmidi_ops snd_mymidi_output_ops = { .open = snd_mymidi_output_open, .close = snd_mymidi_output_close, .trigger = snd_mymidi_output_trigger, }; These callbacks are explained in the `RawMIDI Callbacks`_ section. If there are more than one substream, you should give a unique name to -each of them: - -:: +each of them:: struct snd_rawmidi_substream *substream; list_for_each_entry(substream, @@ -3260,9 +3090,7 @@ device can be accessed as ``substream->rmidi->private_data``. If there is more than one port, your callbacks can determine the port index from the struct snd_rawmidi_substream data passed to each -callback: - -:: +callback:: struct snd_rawmidi_substream *substream; int index = substream->number; @@ -3307,23 +3135,19 @@ of bytes that have been read; this will be less than the number of bytes requested when there are no more data in the buffer. After the data have been transmitted successfully, call :c:func:`snd_rawmidi_transmit_ack()` to remove the data from the -substream buffer: - -:: +substream buffer:: unsigned char data; while (snd_rawmidi_transmit_peek(substream, &data, 1) == 1) { if (snd_mychip_try_to_transmit(data)) snd_rawmidi_transmit_ack(substream, 1); else break; /* hardware FIFO full */ } If you know beforehand that the hardware will accept data, you can use the :c:func:`snd_rawmidi_transmit()` function which reads some -data and removes them from the buffer at once: - -:: +data and removes them from the buffer at once:: while (snd_mychip_transmit_possible()) { unsigned char data; @@ -3358,9 +3182,7 @@ The ``trigger`` callback must not sleep; the actual reading of data from the device is usually done in an interrupt handler. When data reception is enabled, your interrupt handler should call -:c:func:`snd_rawmidi_receive()` for all received data: - -:: +:c:func:`snd_rawmidi_receive()` for all received data:: void snd_mychip_midi_interrupt(...) { @@ -3406,9 +3228,7 @@ whereas in OSS compatible mode, FM registers can be accessed with the OSS direct-FM compatible API in ``/dev/dmfmX`` device. To create the OPL3 component, you have two functions to call. The first -one is a constructor for the ``opl3_t`` instance. - -:: +one is a constructor for the ``opl3_t`` instance:: struct snd_opl3 *opl3; snd_opl3_create(card, lport, rport, OPL3_HW_OPL3_XXX, @@ -3426,9 +3246,7 @@ the opl3 module will allocate the specified ports by itself. When the accessing the hardware requires special method instead of the standard I/O access, you can create opl3 instance separately with -:c:func:`snd_opl3_new()`. - -:: +:c:func:`snd_opl3_new()`:: struct snd_opl3 *opl3; snd_opl3_new(card, OPL3_HW_OPL3_XXX, &opl3); @@ -3445,9 +3263,7 @@ proper state. Note that :c:func:`snd_opl3_create()` always calls it internally. If the opl3 instance is created successfully, then create a hwdep device -for this opl3. - -:: +for this opl3:: struct snd_hwdep *opl3hwdep; snd_opl3_hwdep_new(opl3, 0, 1, &opl3hwdep); @@ -3469,40 +3285,32 @@ the micro code. In such a case, you can create a hwdep ``isa/sb/sb16_csp.c``. The creation of the ``hwdep`` instance is done via -:c:func:`snd_hwdep_new()`. - -:: +:c:func:`snd_hwdep_new()`:: struct snd_hwdep *hw; snd_hwdep_new(card, "My HWDEP", 0, &hw); where the third argument is the index number. You can then pass any pointer value to the ``private_data``. If you -assign a private data, you should define the destructor, too. The -destructor function is set in the ``private_free`` field. - -:: +assign private data, you should define a destructor, too. The +destructor function is set in the ``private_free`` field:: struct mydata *p = kmalloc(sizeof(*p), GFP_KERNEL); hw->private_data = p; hw->private_free = mydata_free; -and the implementation of the destructor would be: - -:: +and the implementation of the destructor would be:: static void mydata_free(struct snd_hwdep *hw) { struct mydata *p = hw->private_data; kfree(p); } The arbitrary file operations can be defined for this instance. The file operators are defined in the ``ops`` table. For example, assume that -this chip needs an ioctl. - -:: +this chip needs an ioctl:: hw->ops.open = mydata_open; hw->ops.ioctl = mydata_ioctl; @@ -3552,92 +3360,87 @@ Buffer Types ALSA provides several different buffer allocation functions depending on the bus and the architecture. All these have a consistent API. The -allocation of physically-contiguous pages is done via +allocation of physically-contiguous pages is done via the :c:func:`snd_malloc_xxx_pages()` function, where xxx is the bus type. -The allocation of pages with fallback is -:c:func:`snd_malloc_xxx_pages_fallback()`. This function tries -to allocate the specified pages but if the pages are not available, it -tries to reduce the page sizes until enough space is found. +The allocation of pages with fallback is done via +:c:func:`snd_dma_alloc_pages_fallback()`. This function tries +to allocate the specified number of pages, but if not enough pages are +available, it tries to reduce the request size until enough space +is found, down to one page. -The release the pages, call :c:func:`snd_free_xxx_pages()` +To release the pages, call the :c:func:`snd_dma_free_pages()` function. Usually, ALSA drivers try to allocate and reserve a large contiguous -physical space at the time the module is loaded for the later use. This +physical space at the time the module is loaded for later use. This is called “pre-allocation”. As already written, you can call the -following function at pcm instance construction time (in the case of PCI -bus). - -:: +following function at PCM instance construction time (in the case of PCI +bus):: snd_pcm_lib_preallocate_pages_for_all(pcm, SNDRV_DMA_TYPE_DEV, &pci->dev, size, max); -where ``size`` is the byte size to be pre-allocated and the ``max`` is -the maximum size to be changed via the ``prealloc`` proc file. The +where ``size`` is the byte size to be pre-allocated and ``max`` is +the maximum size settable via the ``prealloc`` proc file. The allocator will try to get an area as large as possible within the given size. The second argument (type) and the third argument (device pointer) are dependent on the bus. For normal devices, pass the device pointer (typically identical as ``card->dev``) to the third argument with ``SNDRV_DMA_TYPE_DEV`` type. -For the continuous buffer unrelated to the +A continuous buffer unrelated to the bus can be pre-allocated with ``SNDRV_DMA_TYPE_CONTINUOUS`` type. You can pass NULL to the device pointer in that case, which is the -default mode implying to allocate with ``GFP_KERNEL`` flag. +default mode implying to allocate with the ``GFP_KERNEL`` flag. If you need a restricted (lower) address, set up the coherent DMA mask bits for the device, and pass the device pointer, like the normal device memory allocations. For this type, it's still allowed to pass NULL to the device pointer, too, if no address restriction is needed. For the scatter-gather buffers, use ``SNDRV_DMA_TYPE_DEV_SG`` with the device pointer (see the `Non-Contiguous Buffers`_ section). Once the buffer is pre-allocated, you can use the allocator in the -``hw_params`` callback: - -:: +``hw_params`` callback:: snd_pcm_lib_malloc_pages(substream, size); Note that you have to pre-allocate to use this function. -Most of drivers use, though, rather the newly introduced "managed -buffer allocation mode" instead of the manual allocation or release. +But most drivers use the "managed buffer allocation mode" instead +of manual allocation and release. This is done by calling :c:func:`snd_pcm_set_managed_buffer_all()` -instead of :c:func:`snd_pcm_lib_preallocate_pages_for_all()`. - -:: +instead of :c:func:`snd_pcm_lib_preallocate_pages_for_all()`:: snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_DEV, &pci->dev, size, max); -where passed arguments are identical in both functions. +where the passed arguments are identical for both functions. The difference in the managed mode is that PCM core will call :c:func:`snd_pcm_lib_malloc_pages()` internally already before calling the PCM ``hw_params`` callback, and call :c:func:`snd_pcm_lib_free_pages()` after the PCM ``hw_free`` callback automatically. So the driver doesn't have to call these functions explicitly in its callback any -longer. This made many driver code having NULL ``hw_params`` and +longer. This allows many drivers to have NULL ``hw_params`` and ``hw_free`` entries. External Hardware Buffers ------------------------- -Some chips have their own hardware buffers and the DMA transfer from the +Some chips have their own hardware buffers and DMA transfer from the host memory is not available. In such a case, you need to either 1) copy/set the audio data directly to the external hardware buffer, or 2) make an intermediate buffer and copy/set the data from it to the external hardware buffer in interrupts (or in tasklets, preferably). The first case works fine if the external hardware buffer is large enough. This method doesn't need any extra buffers and thus is more -effective. You need to define the ``copy_user`` and ``copy_kernel`` -callbacks for the data transfer, in addition to ``fill_silence`` +efficient. You need to define the ``copy_user`` and ``copy_kernel`` +callbacks for the data transfer, in addition to the ``fill_silence`` callback for playback. However, there is a drawback: it cannot be mmapped. The examples are GUS's GF1 PCM or emu8000's wavetable PCM. @@ -3651,157 +3454,136 @@ buffer instead of the host memory. In this case, mmap is available only on certain architectures like the Intel one. In non-mmap mode, the data cannot be transferred as in the normal way. Thus you need to define the ``copy_user``, ``copy_kernel`` and ``fill_silence`` callbacks as well, -as in the cases above. The examples are found in ``rme32.c`` and +as in the cases above. Examples are found in ``rme32.c`` and ``rme96.c``. The implementation of the ``copy_user``, ``copy_kernel`` and ``silence`` callbacks depends upon whether the hardware supports interleaved or non-interleaved samples. The ``copy_user`` callback is -defined like below, a bit differently depending whether the direction -is playback or capture: - -:: +defined like below, a bit differently depending on whether the direction +is playback or capture:: static int playback_copy_user(struct snd_pcm_substream *substream, int channel, unsigned long pos, void __user *src, unsigned long count); static int capture_copy_user(struct snd_pcm_substream *substream, int channel, unsigned long pos, void __user *dst, unsigned long count); In the case of interleaved samples, the second argument (``channel``) is -not used. The third argument (``pos``) points the current position -offset in bytes. +not used. The third argument (``pos``) specifies the position in bytes. The meaning of the fourth argument is different between playback and capture. For playback, it holds the source data pointer, and for capture, it's the destination data pointer. The last argument is the number of bytes to be copied. What you have to do in this callback is again different between playback and capture directions. In the playback case, you copy the given amount of data (``count``) at the specified pointer (``src``) to the specified -offset (``pos``) on the hardware buffer. When coded like memcpy-like -way, the copy would be like: - -:: +offset (``pos``) in the hardware buffer. When coded like memcpy-like +way, the copy would look like:: my_memcpy_from_user(my_buffer + pos, src, count); For the capture direction, you copy the given amount of data (``count``) -at the specified offset (``pos``) on the hardware buffer to the -specified pointer (``dst``). - -:: +at the specified offset (``pos``) in the hardware buffer to the +specified pointer (``dst``):: my_memcpy_to_user(dst, my_buffer + pos, count); -Here the functions are named as ``from_user`` and ``to_user`` because +Here the functions are named ``from_user`` and ``to_user`` because it's the user-space buffer that is passed to these callbacks. That -is, the callback is supposed to copy from/to the user-space data +is, the callback is supposed to copy data from/to the user-space directly to/from the hardware buffer. Careful readers might notice that these callbacks receive the arguments in bytes, not in frames like other callbacks. It's because -it would make coding easier like the examples above, and also it makes -easier to unify both the interleaved and non-interleaved cases, as -explained in the following. +this makes coding easier like in the examples above, and also it makes +it easier to unify both the interleaved and non-interleaved cases, as +explained below. In the case of non-interleaved samples, the implementation will be a bit -more complicated. The callback is called for each channel, passed by -the second argument, so totally it's called for N-channels times per -transfer. +more complicated. The callback is called for each channel, passed in +the second argument, so in total it's called N times per transfer. -The meaning of other arguments are almost same as the interleaved -case. The callback is supposed to copy the data from/to the given -user-space buffer, but only for the given channel. For the detailed -implementations, please check ``isa/gus/gus_pcm.c`` or -"pci/rme9652/rme9652.c" as examples. +The meaning of the other arguments are almost the same as in the +interleaved case. The callback is supposed to copy the data from/to +the given user-space buffer, but only for the given channel. For +details, please check ``isa/gus/gus_pcm.c`` or ``pci/rme9652/rme9652.c`` +as examples. -The above callbacks are the copy from/to the user-space buffer. There -are some cases where we want copy from/to the kernel-space buffer -instead. In such a case, ``copy_kernel`` callback is called. It'd -look like: - -:: +The above callbacks are the copies from/to the user-space buffer. There +are some cases where we want to copy from/to the kernel-space buffer +instead. In such a case, the ``copy_kernel`` callback is called. It'd +look like:: static int playback_copy_kernel(struct snd_pcm_substream *substream, int channel, unsigned long pos, void *src, unsigned long count); static int capture_copy_kernel(struct snd_pcm_substream *substream, int channel, unsigned long pos, void *dst, unsigned long count); As found easily, the only difference is that the buffer pointer is -without ``__user`` prefix; that is, a kernel-buffer pointer is passed +without a ``__user`` prefix; that is, a kernel-buffer pointer is passed in the fourth argument. Correspondingly, the implementation would be -a version without the user-copy, such as: - -:: +a version without the user-copy, such as:: my_memcpy(my_buffer + pos, src, count); Usually for the playback, another callback ``fill_silence`` is defined. It's implemented in a similar way as the copy callbacks -above: - -:: +above:: static int silence(struct snd_pcm_substream *substream, int channel, unsigned long pos, unsigned long count); The meanings of arguments are the same as in the ``copy_user`` and ``copy_kernel`` callbacks, although there is no buffer pointer argument. In the case of interleaved samples, the channel argument has -no meaning, as well as on ``copy_*`` callbacks. +no meaning, as for the ``copy_*`` callbacks. -The role of ``fill_silence`` callback is to set the given amount -(``count``) of silence data at the specified offset (``pos``) on the +The role of the ``fill_silence`` callback is to set the given amount +(``count``) of silence data at the specified offset (``pos``) in the hardware buffer. Suppose that the data format is signed (that is, the silent-data is 0), and the implementation using a memset-like function -would be like: - -:: +would look like:: my_memset(my_buffer + pos, 0, count); In the case of non-interleaved samples, again, the implementation -becomes a bit more complicated, as it's called N-times per transfer +becomes a bit more complicated, as it's called N times per transfer for each channel. See, for example, ``isa/gus/gus_pcm.c``. Non-Contiguous Buffers ---------------------- -If your hardware supports the page table as in emu10k1 or the buffer -descriptors as in via82xx, you can use the scatter-gather (SG) DMA. ALSA +If your hardware supports a page table as in emu10k1 or buffer +descriptors as in via82xx, you can use scatter-gather (SG) DMA. ALSA provides an interface for handling SG-buffers. The API is provided in ``<sound/pcm.h>``. For creating the SG-buffer handler, call :c:func:`snd_pcm_set_managed_buffer()` or :c:func:`snd_pcm_set_managed_buffer_all()` with -``SNDRV_DMA_TYPE_DEV_SG`` in the PCM constructor like other PCI -pre-allocator. You need to pass ``&pci->dev``, where pci is -the struct pci_dev pointer of the chip as -well. - -:: +``SNDRV_DMA_TYPE_DEV_SG`` in the PCM constructor like for other PCI +pre-allocations. You need to pass ``&pci->dev``, where pci is +the struct pci_dev pointer of the chip as well:: snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_DEV_SG, &pci->dev, size, max); The ``struct snd_sg_buf`` instance is created as -``substream->dma_private`` in turn. You can cast the pointer like: - -:: +``substream->dma_private`` in turn. You can cast the pointer like:: struct snd_sg_buf *sgbuf = (struct snd_sg_buf *)substream->dma_private; -Then in :c:func:`snd_pcm_lib_malloc_pages()` call, the common SG-buffer +Then in the :c:func:`snd_pcm_lib_malloc_pages()` call, the common SG-buffer handler will allocate the non-contiguous kernel pages of the given size -and map them onto the virtually contiguous memory. The virtual pointer -is addressed in runtime->dma_area. The physical address +and map them as virtually contiguous memory. The virtual pointer +is addressed via runtime->dma_area. The physical address (``runtime->dma_addr``) is set to zero, because the buffer is physically non-contiguous. The physical address table is set up in ``sgbuf->table``. You can get the physical address at a certain offset @@ -3814,36 +3596,32 @@ Vmalloc'ed Buffers ------------------ It's possible to use a buffer allocated via :c:func:`vmalloc()`, for -example, for an intermediate buffer. In the recent version of kernel, -you can simply allocate it via standard -:c:func:`snd_pcm_lib_malloc_pages()` and co after setting up the -buffer preallocation with ``SNDRV_DMA_TYPE_VMALLOC`` type. - -:: +example, for an intermediate buffer. +You can simply allocate it via the standard +:c:func:`snd_pcm_lib_malloc_pages()` and co. after setting up the +buffer preallocation with ``SNDRV_DMA_TYPE_VMALLOC`` type:: snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_VMALLOC, NULL, 0, 0); -The NULL is passed to the device pointer argument, which indicates -that the default pages (GFP_KERNEL and GFP_HIGHMEM) will be +NULL is passed as the device pointer argument, which indicates +that default pages (GFP_KERNEL and GFP_HIGHMEM) will be allocated. -Also, note that zero is passed to both the size and the max size -arguments here. Since each vmalloc call should succeed at any time, +Also, note that zero is passed as both the size and the max size +argument here. Since each vmalloc call should succeed at any time, we don't need to pre-allocate the buffers like other continuous pages. Proc Interface ============== ALSA provides an easy interface for procfs. The proc files are very useful for debugging. I recommend you set up proc files if you write a driver and want to get a running status or register dumps. The API is found in ``<sound/info.h>``. -To create a proc file, call :c:func:`snd_card_proc_new()`. - -:: +To create a proc file, call :c:func:`snd_card_proc_new()`:: struct snd_info_entry *entry; int err = snd_card_proc_new(card, "my-file", &entry); @@ -3859,79 +3637,66 @@ automatically in the card registration and release functions. When the creation is successful, the function stores a new instance in the pointer given in the third argument. It is initialized as a text proc file for read only. To use this proc file as a read-only text file -as it is, set the read callback with a private data via -:c:func:`snd_info_set_text_ops()`. - -:: +as-is, set the read callback with private data via +:c:func:`snd_info_set_text_ops()`:: snd_info_set_text_ops(entry, chip, my_proc_read); where the second argument (``chip``) is the private data to be used in -the callbacks. The third parameter specifies the read buffer size and +the callback. The third parameter specifies the read buffer size and the fourth (``my_proc_read``) is the callback function, which is -defined like - -:: +defined like:: static void my_proc_read(struct snd_info_entry *entry, struct snd_info_buffer *buffer); In the read callback, use :c:func:`snd_iprintf()` for output strings, which works just like normal :c:func:`printf()`. For -example, - -:: +example:: static void my_proc_read(struct snd_info_entry *entry, struct snd_info_buffer *buffer) { struct my_chip *chip = entry->private_data; snd_iprintf(buffer, "This is my chip!\n"); snd_iprintf(buffer, "Port = %ld\n", chip->port); } -The file permissions can be changed afterwards. As default, it's set as +The file permissions can be changed afterwards. By default, they are read only for all users. If you want to add write permission for the -user (root as default), do as follows: - -:: +user (root by default), do as follows:: entry->mode = S_IFREG | S_IRUGO | S_IWUSR; -and set the write buffer size and the callback - -:: +and set the write buffer size and the callback:: entry->c.text.write = my_proc_write; -For the write callback, you can use :c:func:`snd_info_get_line()` +In the write callback, you can use :c:func:`snd_info_get_line()` to get a text line, and :c:func:`snd_info_get_str()` to retrieve a string from the line. Some examples are found in ``core/oss/mixer_oss.c``, core/oss/and ``pcm_oss.c``. -For a raw-data proc-file, set the attributes as follows: - -:: +For a raw-data proc-file, set the attributes as follows:: static const struct snd_info_entry_ops my_file_io_ops = { .read = my_file_io_read, }; entry->content = SNDRV_INFO_CONTENT_DATA; entry->private_data = chip; entry->c.ops = &my_file_io_ops; entry->size = 4096; entry->mode = S_IFREG | S_IRUGO; -For the raw data, ``size`` field must be set properly. This specifies +For raw data, ``size`` field must be set properly. This specifies the maximum size of the proc file access. The read/write callbacks of raw mode are more direct than the text mode. You need to use a low-level I/O functions such as -:c:func:`copy_from_user()` and :c:func:`copy_to_user()` to transfer the data. - -:: +:c:func:`copy_from_user()` and :c:func:`copy_to_user()` to transfer the +data:: static ssize_t my_file_io_read(struct snd_info_entry *entry, void *file_private_data, @@ -3956,37 +3721,33 @@ Power Management If the chip is supposed to work with suspend/resume functions, you need to add power-management code to the driver. The additional code for power-management should be ifdef-ed with ``CONFIG_PM``, or annotated -with __maybe_unused attribute; otherwise the compiler will complain -you. +with __maybe_unused attribute; otherwise the compiler will complain. If the driver *fully* supports suspend/resume that is, the device can be properly resumed to its state when suspend was called, you can set the -``SNDRV_PCM_INFO_RESUME`` flag in the pcm info field. Usually, this is +``SNDRV_PCM_INFO_RESUME`` flag in the PCM info field. Usually, this is possible when the registers of the chip can be safely saved and restored to RAM. If this is set, the trigger callback is called with ``SNDRV_PCM_TRIGGER_RESUME`` after the resume callback completes. Even if the driver doesn't support PM fully but partial suspend/resume is still possible, it's still worthy to implement suspend/resume callbacks. In such a case, applications would reset the status by calling :c:func:`snd_pcm_prepare()` and restart the stream appropriately. Hence, you can define suspend/resume callbacks below but -don't set ``SNDRV_PCM_INFO_RESUME`` info flag to the PCM. +don't set the ``SNDRV_PCM_INFO_RESUME`` info flag to the PCM. Note that the trigger with SUSPEND can always be called when :c:func:`snd_pcm_suspend_all()` is called, regardless of the ``SNDRV_PCM_INFO_RESUME`` flag. The ``RESUME`` flag affects only the behavior of :c:func:`snd_pcm_resume()`. (Thus, in theory, ``SNDRV_PCM_TRIGGER_RESUME`` isn't needed to be handled in the trigger callback when no ``SNDRV_PCM_INFO_RESUME`` flag is set. But, it's better to keep it for compatibility reasons.) -In the earlier version of ALSA drivers, a common power-management layer -was provided, but it has been removed. The driver needs to define the +The driver needs to define the suspend/resume hooks according to the bus the device is connected to. In -the case of PCI drivers, the callbacks look like below: - -:: +the case of PCI drivers, the callbacks look like below:: static int __maybe_unused snd_my_suspend(struct device *dev) { @@ -3999,7 +3760,7 @@ the case of PCI drivers, the callbacks look like below: return 0; } -The scheme of the real suspend job is as follows. +The scheme of the real suspend job is as follows: 1. Retrieve the card and the chip data. @@ -4013,9 +3774,7 @@ The scheme of the real suspend job is as follows. 5. Stop the hardware if necessary. -A typical code would be like: - -:: +Typical code would look like:: static int __maybe_unused mychip_suspend(struct device *dev) { @@ -4034,24 +3793,22 @@ A typical code would be like: } -The scheme of the real resume job is as follows. +The scheme of the real resume job is as follows: 1. Retrieve the card and the chip data. 2. Re-initialize the chip. 3. Restore the saved registers if necessary. -4. Resume the mixer, e.g. calling :c:func:`snd_ac97_resume()`. +4. Resume the mixer, e.g. by calling :c:func:`snd_ac97_resume()`. 5. Restart the hardware (if any). 6. Call :c:func:`snd_power_change_state()` with ``SNDRV_CTL_POWER_D0`` to notify the processes. -A typical code would be like: - -:: +Typical code would look like:: static int __maybe_unused mychip_resume(struct pci_dev *pci) { @@ -4078,9 +3835,7 @@ been already suspended via its own PM ops calling OK, we have all callbacks now. Let's set them up. In the initialization of the card, make sure that you can get the chip data from the card instance, typically via ``private_data`` field, in case you created the -chip data individually. - -:: +chip data individually:: static int snd_mychip_probe(struct pci_dev *pci, const struct pci_device_id *pci_id) @@ -4100,9 +3855,7 @@ chip data individually. } When you created the chip data with :c:func:`snd_card_new()`, it's -anyway accessible via ``private_data`` field. - -:: +anyway accessible via ``private_data`` field:: static int snd_mychip_probe(struct pci_dev *pci, const struct pci_device_id *pci_id) @@ -4119,14 +3872,12 @@ anyway accessible via ``private_data`` field. .... } -If you need a space to save the registers, allocate the buffer for it +If you need space to save the registers, allocate the buffer for it here, too, since it would be fatal if you cannot allocate a memory in the suspend phase. The allocated buffer should be released in the corresponding destructor. -And next, set suspend/resume callbacks to the pci_driver. - -:: +And next, set suspend/resume callbacks to the pci_driver:: static SIMPLE_DEV_PM_OPS(snd_my_pm_ops, mychip_suspend, mychip_resume); @@ -4146,9 +3897,7 @@ have the ``index``, ``id`` and ``enable`` options. If the module supports multiple cards (usually up to 8 = ``SNDRV_CARDS`` cards), they should be arrays. The default initial values are defined -already as constants for easier programming: - -:: +already as constants for easier programming:: static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX; static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR; @@ -4162,9 +3911,7 @@ The module parameters must be declared with the standard ``module_param()``, ``module_param_array()`` and :c:func:`MODULE_PARM_DESC()` macros. -The typical coding would be like below: - -:: +Typical code would look as below:: #define CARD_NAME "My Chip" @@ -4177,9 +3924,7 @@ The typical coding would be like below: Also, don't forget to define the module description and the license. Especially, the recent modprobe requires to define the -module license as GPL, etc., otherwise the system is shown as “tainted”. - -:: +module license as GPL, etc., otherwise the system is shown as “tainted”:: MODULE_DESCRIPTION("Sound driver for My Chip"); MODULE_LICENSE("GPL"); @@ -4242,50 +3987,50 @@ Driver with A Single Source File 1. Modify sound/pci/Makefile - Suppose you have a file xyz.c. Add the following two lines - -:: + Suppose you have a file xyz.c. Add the following two lines:: snd-xyz-objs := xyz.o obj-$(CONFIG_SND_XYZ) += snd-xyz.o 2. Create the Kconfig entry - Add the new entry of Kconfig for your xyz driver. config SND_XYZ - tristate "Foobar XYZ" depends on SND select SND_PCM help Say Y here - to include support for Foobar XYZ soundcard. To compile this driver - as a module, choose M here: the module will be called snd-xyz. the - line, select SND_PCM, specifies that the driver xyz supports PCM. In - addition to SND_PCM, the following components are supported for - select command: SND_RAWMIDI, SND_TIMER, SND_HWDEP, - SND_MPU401_UART, SND_OPL3_LIB, SND_OPL4_LIB, SND_VX_LIB, - SND_AC97_CODEC. Add the select command for each supported - component. + Add the new entry of Kconfig for your xyz driver:: - Note that some selections imply the lowlevel selections. For example, - PCM includes TIMER, MPU401_UART includes RAWMIDI, AC97_CODEC - includes PCM, and OPL3_LIB includes HWDEP. You don't need to give - the lowlevel selections again. + config SND_XYZ + tristate "Foobar XYZ" + depends on SND + select SND_PCM + help + Say Y here to include support for Foobar XYZ soundcard. + To compile this driver as a module, choose M here: + the module will be called snd-xyz. - For the details of Kconfig script, refer to the kbuild documentation. +The line ``select SND_PCM`` specifies that the driver xyz supports PCM. +In addition to SND_PCM, the following components are supported for +select command: SND_RAWMIDI, SND_TIMER, SND_HWDEP, SND_MPU401_UART, +SND_OPL3_LIB, SND_OPL4_LIB, SND_VX_LIB, SND_AC97_CODEC. +Add the select command for each supported component. + +Note that some selections imply the lowlevel selections. For example, +PCM includes TIMER, MPU401_UART includes RAWMIDI, AC97_CODEC +includes PCM, and OPL3_LIB includes HWDEP. You don't need to give +the lowlevel selections again. + +For the details of Kconfig script, refer to the kbuild documentation. Drivers with Several Source Files --------------------------------- Suppose that the driver snd-xyz have several source files. They are located in the new subdirectory, sound/pci/xyz. 1. Add a new directory (``sound/pci/xyz``) in ``sound/pci/Makefile`` - as below - -:: + as below:: obj-$(CONFIG_SND) += sound/pci/xyz/ -2. Under the directory ``sound/pci/xyz``, create a Makefile - -:: +2. Under the directory ``sound/pci/xyz``, create a Makefile:: snd-xyz-objs := xyz.o abc.o def.o obj-$(CONFIG_SND_XYZ) += snd-xyz.o -- 2.40.0.152.g15d061e6df

2 1

[PATCH alsa-lib] pcm: hw: setup explicit silencing for snd_pcm_drain by default
by Jaroslav Kysela 21 Apr '23

21 Apr '23

RFC: Patch for alsa-lib. Not tested. For a discussion. Some applications may not follow the period_size transfer blocks and also the driver developers may not follow the consequeces of the access beyond valid samples in the playback DMA buffer. To avoid clicks, fill a little silence at the end of the playback ring buffer when the snd_pcm_drain() is called. TODO: - add SND_PCM_NO_DRAIN_SILENCE as a new flag for snd_pcm_open() - make this behaviour configurable (plugin config) Cc: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> Signed-off-by: Jaroslav Kysela <perex(a)perex.cz> --- src/pcm/pcm.c | 33 ++++++++++++++++++++------------- src/pcm/pcm_hw.c | 45 +++++++++++++++++++++++++++++++++++++++++++++ src/pcm/pcm_local.h | 4 ++++ 3 files changed, 69 insertions(+), 13 deletions(-) diff --git a/src/pcm/pcm.c b/src/pcm/pcm.c index 2b966d44..88b13ed4 100644 --- a/src/pcm/pcm.c +++ b/src/pcm/pcm.c @@ -6167,6 +6167,25 @@ int snd_pcm_hw_params_get_min_align(const snd_pcm_hw_params_t *params, snd_pcm_u return 0; } +#ifndef DOXYGEN +void snd_pcm_sw_params_current_no_lock(snd_pcm_t *pcm, snd_pcm_sw_params_t *params) +{ + params->proto = SNDRV_PCM_VERSION; + params->tstamp_mode = pcm->tstamp_mode; + params->tstamp_type = pcm->tstamp_type; + params->period_step = pcm->period_step; + params->sleep_min = 0; + params->avail_min = pcm->avail_min; + sw_set_period_event(params, pcm->period_event); + params->xfer_align = 1; + params->start_threshold = pcm->start_threshold; + params->stop_threshold = pcm->stop_threshold; + params->silence_threshold = pcm->silence_threshold; + params->silence_size = pcm->silence_size; + params->boundary = pcm->boundary; +} +#endif + /** * \brief Return current software configuration for a PCM * \param pcm PCM handle @@ -6183,19 +6202,7 @@ int snd_pcm_sw_params_current(snd_pcm_t *pcm, snd_pcm_sw_params_t *params) return -EIO; } __snd_pcm_lock(pcm); /* forced lock due to pcm field changes */ - params->proto = SNDRV_PCM_VERSION; - params->tstamp_mode = pcm->tstamp_mode; - params->tstamp_type = pcm->tstamp_type; - params->period_step = pcm->period_step; - params->sleep_min = 0; - params->avail_min = pcm->avail_min; - sw_set_period_event(params, pcm->period_event); - params->xfer_align = 1; - params->start_threshold = pcm->start_threshold; - params->stop_threshold = pcm->stop_threshold; - params->silence_threshold = pcm->silence_threshold; - params->silence_size = pcm->silence_size; - params->boundary = pcm->boundary; + snd_pcm_sw_params_current_no_lock(pcm, params); __snd_pcm_unlock(pcm); return 0; } diff --git a/src/pcm/pcm_hw.c b/src/pcm/pcm_hw.c index daa3e1ff..4995b2cd 100644 --- a/src/pcm/pcm_hw.c +++ b/src/pcm/pcm_hw.c @@ -98,6 +98,8 @@ typedef struct { bool mmap_control_fallbacked; struct snd_pcm_sync_ptr *sync_ptr; + bool prepare_reset_sw_params; + int period_event; snd_timer_t *period_timer; struct pollfd period_timer_pfd; @@ -534,6 +536,7 @@ static int snd_pcm_hw_sw_params(snd_pcm_t *pcm, snd_pcm_sw_params_t * params) SYSMSG("SNDRV_PCM_IOCTL_SW_PARAMS failed (%i)", err); goto out; } + hw->prepare_reset_sw_params = false; if ((snd_pcm_tstamp_type_t) params->tstamp_type != pcm->tstamp_type) { if (hw->version < SNDRV_PROTOCOL_VERSION(2, 0, 12)) { int on = (snd_pcm_tstamp_type_t) params->tstamp_type == @@ -660,7 +663,18 @@ static int snd_pcm_hw_hwsync(snd_pcm_t *pcm) static int snd_pcm_hw_prepare(snd_pcm_t *pcm) { snd_pcm_hw_t *hw = pcm->private_data; + snd_pcm_sw_params_t sw_params; int fd = hw->fd, err; + + if (hw->prepare_reset_sw_params) { + snd_pcm_sw_params_current_no_lock(pcm, &sw_params); + if (ioctl(hw->fd, SNDRV_PCM_IOCTL_SW_PARAMS, sw_params) < 0) { + err = -errno; + SYSMSG("SNDRV_PCM_IOCTL_SW_PARAMS failed (%i)", err); + return err; + } + hw->prepare_reset_sw_params = false; + } if (ioctl(fd, SNDRV_PCM_IOCTL_PREPARE) < 0) { err = -errno; SYSMSG("SNDRV_PCM_IOCTL_PREPARE failed (%i)", err); @@ -718,7 +732,38 @@ static int snd_pcm_hw_drop(snd_pcm_t *pcm) static int snd_pcm_hw_drain(snd_pcm_t *pcm) { snd_pcm_hw_t *hw = pcm->private_data; + snd_pcm_sw_params_t sw_params; + snd_pcm_uframes_t silence_size; int err; + + if (pcm->stream != SND_PCM_STREAM_PLAYBACK) + goto __skip_silence; + /* compute end silence size, align to period size + extra time */ + snd_pcm_sw_params_current_no_lock(pcm, &sw_params); + if ((pcm->buffer_size % pcm->period_size) == 0) { + silence_size = pcm->period_size - (pcm->period_size % *pcm->appl.ptr); + if (silence_size == pcm->period_size) + silence_size = 0; + } else { + /* it not not easy to compute the period cross point + * in this case because boundary is aligned only + * to the buffer_size - use the full range (period) + */ + silence_size = pcm->period_size; + } + silence_size += pcm->rate / 10; /* 1/10th of second */ + if (sw_params.silence_size < silence_size) { + /* fill silence soon as possible (in the bellow ioctl) */ + sw_params.silence_threshold = pcm->buffer_size; + sw_params.silence_size = silence_size; + if (ioctl(hw->fd, SNDRV_PCM_IOCTL_SW_PARAMS, sw_params) < 0) { + err = -errno; + SYSMSG("SNDRV_PCM_IOCTL_SW_PARAMS failed (%i)", err); + return err; + } + hw->prepare_reset_sw_params = true; + } +__skip_silence: if (ioctl(hw->fd, SNDRV_PCM_IOCTL_DRAIN) < 0) { err = -errno; SYSMSG("SNDRV_PCM_IOCTL_DRAIN failed (%i)", err); diff --git a/src/pcm/pcm_local.h b/src/pcm/pcm_local.h index ae0c44bf..4a859cd1 100644 --- a/src/pcm/pcm_local.h +++ b/src/pcm/pcm_local.h @@ -366,6 +366,8 @@ struct _snd_pcm { snd1_pcm_hw_param_get_max #define snd_pcm_hw_param_name \ snd1_pcm_hw_param_name +#define snd_pcm_sw_params_current_no_lock \ + snd1_pcm_sw_params_current_no_lock int snd_pcm_new(snd_pcm_t **pcmp, snd_pcm_type_t type, const char *name, snd_pcm_stream_t stream, int mode); @@ -390,6 +392,8 @@ void snd_pcm_mmap_appl_forward(snd_pcm_t *pcm, snd_pcm_uframes_t frames); void snd_pcm_mmap_hw_backward(snd_pcm_t *pcm, snd_pcm_uframes_t frames); void snd_pcm_mmap_hw_forward(snd_pcm_t *pcm, snd_pcm_uframes_t frames); +void snd_pcm_sw_params_current_no_lock(snd_pcm_t *pcm, snd_pcm_sw_params_t *params); + snd_pcm_sframes_t snd_pcm_mmap_writei(snd_pcm_t *pcm, const void *buffer, snd_pcm_uframes_t size); snd_pcm_sframes_t snd_pcm_mmap_readi(snd_pcm_t *pcm, void *buffer, snd_pcm_uframes_t size); snd_pcm_sframes_t snd_pcm_mmap_writen(snd_pcm_t *pcm, void **bufs, snd_pcm_uframes_t size); -- 2.39.2

1 0

Realtek ALC 4080 on MSI B650 Tomahawk
by GitHub issues - opened 21 Apr '23

21 Apr '23

alsa-project/alsa-ucm-conf issue #306 was opened from arleyantes: I have Realtek ALC 4080 on an MSI B650 Tomahawk and the chip is not getting recognized, its usb id is "Bus 001 Device 003: ID 0db0:422d Micro Star International USB Audio". Manually changing the ids in ucm in File /usr/share/alsa/ucm2/USB-Audio/USB-Audio.conf made it show up correctly. Issue URL : https://github.com/alsa-project/alsa-ucm-conf/issues/306 Repository URL: https://github.com/alsa-project/alsa-ucm-conf

1 0

[PATCH v2 1/2] ALSA: pcm: rewrite snd_pcm_playback_silence()
by Oswald Buddenhagen 21 Apr '23

21 Apr '23

The auto-silencer supports two modes: "thresholded" to fill up "just enough", and "top-up" to fill up "as much as possible". The two modes used rather distinct code paths, which this patch unifies. The only remaining distinction is how much we actually want to fill. This fixes a bug in thresholded mode, where we failed to use new_hw_ptr, resulting in under-fill. Top-up mode is now more well-behaved and much easier to understand in corner cases. This also updates comments in the proximity of silencing-related data structures. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- v2: - removed useless boundary check - got rid of casts by using a signed type for deltas. i did not adjust the style of the conditionals, because it's not clear whether the hangup was actually over that, or merely over the casts. - dropped use of C99 comments where the surroundings suggest it. (in the case of the interspersed multi-line comments, that doesn't look like an improvement to me at all ...) - swapped the `added` and `hw_avail` calculation blocks to reduce subsequent churn. it's more logical that way anyway. --- .../kernel-api/writing-an-alsa-driver.rst | 17 ++-- include/sound/pcm.h | 14 +-- include/uapi/sound/asound.h | 11 ++- sound/core/pcm_lib.c | 86 ++++++++----------- sound/core/pcm_local.h | 3 +- sound/core/pcm_native.c | 6 +- 6 files changed, 66 insertions(+), 71 deletions(-) diff --git a/Documentation/sound/kernel-api/writing-an-alsa-driver.rst b/Documentation/sound/kernel-api/writing-an-alsa-driver.rst index a368529e8ed3..e37d9dba320d 100644 --- a/Documentation/sound/kernel-api/writing-an-alsa-driver.rst +++ b/Documentation/sound/kernel-api/writing-an-alsa-driver.rst @@ -1577,14 +1577,19 @@ are the contents of this file: unsigned int period_step; unsigned int sleep_min; /* min ticks to sleep */ snd_pcm_uframes_t start_threshold; - snd_pcm_uframes_t stop_threshold; - snd_pcm_uframes_t silence_threshold; /* Silence filling happens when - noise is nearest than this */ - snd_pcm_uframes_t silence_size; /* Silence filling size */ + /* + * The following two thresholds alleviate playback buffer underruns; when + * hw_avail drops below the threshold, the respective action is triggered: + */ + snd_pcm_uframes_t stop_threshold; /* - stop playback */ + snd_pcm_uframes_t silence_threshold; /* - pre-fill buffer with silence */ + snd_pcm_uframes_t silence_size; /* max size of silence pre-fill; when >= boundary, + * fill played area with silence immediately */ snd_pcm_uframes_t boundary; /* pointers wrap point */ - snd_pcm_uframes_t silenced_start; - snd_pcm_uframes_t silenced_size; + /* internal data of auto-silencer */ + snd_pcm_uframes_t silence_start; /* starting pointer to silence area */ + snd_pcm_uframes_t silence_filled; /* size filled with silence */ snd_pcm_sync_id_t sync; /* hardware synchronization ID */ diff --git a/include/sound/pcm.h b/include/sound/pcm.h index 27040b472a4f..19f564606ac4 100644 --- a/include/sound/pcm.h +++ b/include/sound/pcm.h @@ -378,18 +378,18 @@ struct snd_pcm_runtime { unsigned int rate_den; unsigned int no_period_wakeup: 1; - /* -- SW params -- */ - int tstamp_mode; /* mmap timestamp is updated */ + /* -- SW params; see struct snd_pcm_sw_params for comments -- */ + int tstamp_mode; unsigned int period_step; snd_pcm_uframes_t start_threshold; snd_pcm_uframes_t stop_threshold; - snd_pcm_uframes_t silence_threshold; /* Silence filling happens when - noise is nearest than this */ - snd_pcm_uframes_t silence_size; /* Silence filling size */ - snd_pcm_uframes_t boundary; /* pointers wrap point */ + snd_pcm_uframes_t silence_threshold; + snd_pcm_uframes_t silence_size; + snd_pcm_uframes_t boundary; + /* internal data of auto-silencer */ snd_pcm_uframes_t silence_start; /* starting pointer to silence area */ - snd_pcm_uframes_t silence_filled; /* size filled with silence */ + snd_pcm_uframes_t silence_filled; /* already filled part of silence area */ union snd_pcm_sync_id sync; /* hardware synchronization ID */ diff --git a/include/uapi/sound/asound.h b/include/uapi/sound/asound.h index de6810e94abe..a255a891eb81 100644 --- a/include/uapi/sound/asound.h +++ b/include/uapi/sound/asound.h @@ -429,9 +429,14 @@ struct snd_pcm_sw_params { snd_pcm_uframes_t avail_min; /* min avail frames for wakeup */ snd_pcm_uframes_t xfer_align; /* obsolete: xfer size need to be a multiple */ snd_pcm_uframes_t start_threshold; /* min hw_avail frames for automatic start */ - snd_pcm_uframes_t stop_threshold; /* min avail frames for automatic stop */ - snd_pcm_uframes_t silence_threshold; /* min distance from noise for silence filling */ - snd_pcm_uframes_t silence_size; /* silence block size */ + /* + * The following two thresholds alleviate playback buffer underruns; when + * hw_avail drops below the threshold, the respective action is triggered: + */ + snd_pcm_uframes_t stop_threshold; /* - stop playback */ + snd_pcm_uframes_t silence_threshold; /* - pre-fill buffer with silence */ + snd_pcm_uframes_t silence_size; /* max size of silence pre-fill; when >= boundary, + * fill played area with silence immediately */ snd_pcm_uframes_t boundary; /* pointers wrap point */ unsigned int proto; /* protocol version */ unsigned int tstamp_type; /* timestamp type (req. proto >= 2.0.12) */ diff --git a/sound/core/pcm_lib.c b/sound/core/pcm_lib.c index 02fd65993e7e..5bb2129cceac 100644 --- a/sound/core/pcm_lib.c +++ b/sound/core/pcm_lib.c @@ -42,70 +42,56 @@ static int fill_silence_frames(struct snd_pcm_substream *substream, * * when runtime->silence_size >= runtime->boundary - fill processed area with silence immediately */ -void snd_pcm_playback_silence(struct snd_pcm_substream *substream, snd_pcm_uframes_t new_hw_ptr) +void snd_pcm_playback_silence(struct snd_pcm_substream *substream) { struct snd_pcm_runtime *runtime = substream->runtime; - snd_pcm_uframes_t frames, ofs, transfer; + snd_pcm_uframes_t appl_ptr = READ_ONCE(runtime->control->appl_ptr); + snd_pcm_sframes_t added, hw_avail, frames; + snd_pcm_uframes_t noise_dist, ofs, transfer; int err; + added = appl_ptr - runtime->silence_start; + if (added) { + if (added < 0) + added += runtime->boundary; + if (added < runtime->silence_filled) + runtime->silence_filled -= added; + else + runtime->silence_filled = 0; + runtime->silence_start = appl_ptr; + } + + // This will "legitimately" turn negative on underrun, and will be mangled + // into a huge number by the boundary crossing handling. The initial state + // might also be not quite sane. The code below MUST account for these cases. + hw_avail = appl_ptr - runtime->status->hw_ptr; + if (hw_avail < 0) + hw_avail += runtime->boundary; + + noise_dist = hw_avail + runtime->silence_filled; if (runtime->silence_size < runtime->boundary) { - snd_pcm_sframes_t noise_dist, n; - snd_pcm_uframes_t appl_ptr = READ_ONCE(runtime->control->appl_ptr); - if (runtime->silence_start != appl_ptr) { - n = appl_ptr - runtime->silence_start; - if (n < 0) - n += runtime->boundary; - if ((snd_pcm_uframes_t)n < runtime->silence_filled) - runtime->silence_filled -= n; - else - runtime->silence_filled = 0; - runtime->silence_start = appl_ptr; - } - if (runtime->silence_filled >= runtime->buffer_size) - return; - noise_dist = snd_pcm_playback_hw_avail(runtime) + runtime->silence_filled; - if (noise_dist >= (snd_pcm_sframes_t) runtime->silence_threshold) - return; frames = runtime->silence_threshold - noise_dist; + if (frames <= 0) + return; if (frames > runtime->silence_size) frames = runtime->silence_size; } else { - if (new_hw_ptr == ULONG_MAX) { /* initialization */ - snd_pcm_sframes_t avail = snd_pcm_playback_hw_avail(runtime); - if (avail > runtime->buffer_size) - avail = runtime->buffer_size; - runtime->silence_filled = avail > 0 ? avail : 0; - runtime->silence_start = (runtime->status->hw_ptr + - runtime->silence_filled) % - runtime->boundary; - } else { - ofs = runtime->status->hw_ptr; - frames = new_hw_ptr - ofs; - if ((snd_pcm_sframes_t)frames < 0) - frames += runtime->boundary; - runtime->silence_filled -= frames; - if ((snd_pcm_sframes_t)runtime->silence_filled < 0) { - runtime->silence_filled = 0; - runtime->silence_start = new_hw_ptr; - } else { - runtime->silence_start = ofs; - } - } - frames = runtime->buffer_size - runtime->silence_filled; + frames = runtime->buffer_size - noise_dist; + if (frames <= 0) + return; } + if (snd_BUG_ON(frames > runtime->buffer_size)) return; - if (frames == 0) - return; - ofs = runtime->silence_start % runtime->buffer_size; - while (frames > 0) { + ofs = (runtime->silence_start + runtime->silence_filled) % runtime->buffer_size; + do { transfer = ofs + frames > runtime->buffer_size ? runtime->buffer_size - ofs : frames; err = fill_silence_frames(substream, ofs, transfer); snd_BUG_ON(err < 0); runtime->silence_filled += transfer; frames -= transfer; ofs = 0; - } + } while (frames > 0); snd_pcm_dma_buffer_sync(substream, SNDRV_DMA_SYNC_DEVICE); } @@ -439,10 +425,6 @@ static int snd_pcm_update_hw_ptr0(struct snd_pcm_substream *substream, return 0; } - if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && - runtime->silence_size > 0) - snd_pcm_playback_silence(substream, new_hw_ptr); - if (in_interrupt) { delta = new_hw_ptr - runtime->hw_ptr_interrupt; if (delta < 0) @@ -460,6 +442,10 @@ static int snd_pcm_update_hw_ptr0(struct snd_pcm_substream *substream, runtime->hw_ptr_wrap += runtime->boundary; } + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && + runtime->silence_size > 0) + snd_pcm_playback_silence(substream); + update_audio_tstamp(substream, &curr_tstamp, &audio_tstamp); return snd_pcm_update_state(substream, runtime); diff --git a/sound/core/pcm_local.h b/sound/core/pcm_local.h index ecb21697ae3a..42fe3a4e9154 100644 --- a/sound/core/pcm_local.h +++ b/sound/core/pcm_local.h @@ -29,8 +29,7 @@ int snd_pcm_update_state(struct snd_pcm_substream *substream, struct snd_pcm_runtime *runtime); int snd_pcm_update_hw_ptr(struct snd_pcm_substream *substream); -void snd_pcm_playback_silence(struct snd_pcm_substream *substream, - snd_pcm_uframes_t new_hw_ptr); +void snd_pcm_playback_silence(struct snd_pcm_substream *substream); static inline snd_pcm_uframes_t snd_pcm_avail(struct snd_pcm_substream *substream) diff --git a/sound/core/pcm_native.c b/sound/core/pcm_native.c index 331380c2438b..0e3e7997dc58 100644 --- a/sound/core/pcm_native.c +++ b/sound/core/pcm_native.c @@ -958,7 +958,7 @@ static int snd_pcm_sw_params(struct snd_pcm_substream *substream, if (snd_pcm_running(substream)) { if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && runtime->silence_size > 0) - snd_pcm_playback_silence(substream, ULONG_MAX); + snd_pcm_playback_silence(substream); err = snd_pcm_update_state(substream, runtime); } snd_pcm_stream_unlock_irq(substream); @@ -1455,7 +1455,7 @@ static void snd_pcm_post_start(struct snd_pcm_substream *substream, __snd_pcm_set_state(runtime, state); if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && runtime->silence_size > 0) - snd_pcm_playback_silence(substream, ULONG_MAX); + snd_pcm_playback_silence(substream); snd_pcm_timer_notify(substream, SNDRV_TIMER_EVENT_MSTART); } @@ -1916,7 +1916,7 @@ static void snd_pcm_post_reset(struct snd_pcm_substream *substream, runtime->control->appl_ptr = runtime->status->hw_ptr; if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && runtime->silence_size > 0) - snd_pcm_playback_silence(substream, ULONG_MAX); + snd_pcm_playback_silence(substream); snd_pcm_stream_unlock_irq(substream); } -- 2.40.0.152.g15d061e6df

3 6

DAC not connecting after waking from suspend.
by GitHub issues - opened 21 Apr '23

21 Apr '23

alsa-project/alsa-lib issue #313 was opened from ad-on-is: A strange issue started happening, with my USB connected DAC (fiio k3). After waking from sleep/suspend the DAC is not recognized anymore, unless I replug it. ``` alsa-lib.i686 1.2.8-3.fc38 @fedora alsa-lib.x86_64 1.2.8-3.fc38 @anaconda alsa-sof-firmware.noarch 2.2.4-3.fc38 @anaconda alsa-ucm.noarch 1.2.8-3.fc38 @anaconda alsa-utils.x86_64 1.2.8-2.fc38 @anaconda pipewire-alsa.i686 0.3.69-1.fc38 @updates pipewire-alsa.x86_64 0.3.69-1.fc38 @updates qemu-audio-alsa.x86_64 2:7.2.0-6.fc38 @anaconda wine-alsa.i686 8.5-1.fc38 @updates wine-alsa.x86_64 8.5-1.fc38 @updates ``` ``` when it's connected: cat /proc/asound/modules 1 0 snd_usb_audio 2 1 snd_hda_intel 3 2 snd_usb_audio 4 3 snd_hda_intel 5 4 snd_usb_audio 6 5 snd_usb_audio after wakeup: cat /proc/asound/modules 1 0 snd_usb_audio 2 1 snd_hda_intel 3 2 snd_usb_audio 4 3 snd_hda_intel 5 4 snd_usb_audio ``` If you need any further info, let me know. Issue URL : https://github.com/alsa-project/alsa-lib/issues/313 Repository URL: https://github.com/alsa-project/alsa-lib

1 0

[RFC PATCH] docs: sound: kernel-api: writing-an-alsa-driver.rst: add FIXMEs
by Oswald Buddenhagen 21 Apr '23

21 Apr '23

Consider this a review by an under-informed reader. --- .../sound/kernel-api/writing-an-alsa-driver.rst | 14 +++++++++++++- 1 file changed, 13 insertions(+), 1 deletion(-) diff --git a/Documentation/sound/kernel-api/writing-an-alsa-driver.rst b/Documentation/sound/kernel-api/writing-an-alsa-driver.rst index b58f15f2dc7c..1b605867dbd0 100644 --- a/Documentation/sound/kernel-api/writing-an-alsa-driver.rst +++ b/Documentation/sound/kernel-api/writing-an-alsa-driver.rst @@ -82,10 +82,11 @@ core/seq/oss This contains the OSS sequencer emulation code. include directory ----------------- +// FIXME: needs update for uapi This is the place for the public header files of ALSA drivers, which are to be exported to user-space, or included by several files in different directories. Basically, the private header files should not be placed in this directory, but you may still find files there, due to historical reasons :) @@ -1646,11 +1647,11 @@ Typically, you'll have a hardware descriptor as below:: The “period” is a term that corresponds to a fragment in the OSS world. The period defines the point at which a PCM interrupt is generated. This point strongly depends on the hardware. Generally, a smaller period size will give you more interrupts, that is, - more controls. In the case of capture, this size defines the input + more controls (FIXME: huh? granularity, maybe?). In the case of capture, this size defines the input latency. On the other hand, the whole buffer size defines the output latency for the playback direction. - There is also a field ``fifo_size``. This specifies the size of the hardware FIFO, but currently it is neither used by the drivers nor @@ -1682,10 +1683,11 @@ frames as unsigned integer while ``snd_pcm_sframes_t`` is for frames as signed integer. DMA Buffer Information ~~~~~~~~~~~~~~~~~~~~~~ +// FIXME: this is outdated; dma_private is available only through dma_buffer_p! The DMA buffer is defined by the following four fields: ``dma_area``, ``dma_addr``, ``dma_bytes`` and ``dma_private``. ``dma_area`` holds the buffer pointer (the logical address). You can call :c:func:`memcpy()` from/to this pointer. Meanwhile, ``dma_addr`` holds the physical address of the buffer. This field is specified only when @@ -1709,10 +1711,11 @@ Running Status The running status can be referred via ``runtime->status``. This is a pointer to a struct snd_pcm_mmap_status record. For example, you can get the current DMA hardware pointer via ``runtime->status->hw_ptr``. +// FIXME: DMA application pointer is not explained. The DMA application pointer can be referred via ``runtime->control``, which points to a struct snd_pcm_mmap_control record. However, accessing this value directly is not recommended. Private Data @@ -2010,10 +2013,12 @@ is called by the interrupt routine. Then the PCM middle layer updates the position and calculates the available space, and wakes up the sleeping poll threads, etc. This callback is also atomic by default. +FIXME: this does not specifiy whether this is the pre- or post-fifo position. + copy_user, copy_kernel and fill_silence ops ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ These callbacks are not mandatory, and can be omitted in most cases. These callbacks are used when the hardware buffer cannot be in the @@ -2384,10 +2389,14 @@ fields. The ``name`` is the name identifier string. Since ALSA 0.9.x, the control name is very important, because its role is classified from its name. There are pre-defined standard control names. The details are described in the `Control Names`_ subsection. +// This is a questionable design, IMO. Why user-space heuristics when +// the driver could set the roles/capabilities? This would avoid +// problems like the Tone Control sliders (unlike the switch?!) being +// misclassified as applying also to capture. The ``index`` field holds the index number of this control. If there are several different controls with the same name, they can be distinguished by the index number. This is the case when several codecs exist on the card. If the index is zero, you can omit the @@ -2485,10 +2494,11 @@ a control constantly. When the control may be updated, but currently has no effect on anything, setting the ``INACTIVE`` flag may be appropriate. For example, PCM controls should be inactive while no PCM device is open. There are ``LOCK`` and ``OWNER`` flags to change the write permissions. +// FIXME: explain. Control Callbacks ----------------- info callback @@ -3355,10 +3365,11 @@ Buffer and Memory Management ============================ Buffer Types ------------ +// FIXME: this appears obsolete, i only found one pair of functions. ALSA provides several different buffer allocation functions depending on the bus and the architecture. All these have a consistent API. The allocation of physically-contiguous pages is done via the :c:func:`snd_malloc_xxx_pages()` function, where xxx is the bus type. @@ -3670,10 +3681,11 @@ user (root by default), do as follows:: entry->mode = S_IFREG | S_IRUGO | S_IWUSR; and set the write buffer size and the callback:: entry->c.text.write = my_proc_write; + // FIXME: something's missing here? In the write callback, you can use :c:func:`snd_info_get_line()` to get a text line, and :c:func:`snd_info_get_str()` to retrieve a string from the line. Some examples are found in ``core/oss/mixer_oss.c``, core/oss/and ``pcm_oss.c``. -- 2.40.0.152.g15d061e6df

3 9

[linux-next:master] BUILD REGRESSION 44bf136283e567b2b62653be7630e7511da41da2
by kernel test robot 21 Apr '23

21 Apr '23

tree/branch: https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git master branch HEAD: 44bf136283e567b2b62653be7630e7511da41da2 Add linux-next specific files for 20230420 Error/Warning reports: https://lore.kernel.org/oe-kbuild-all/202304172004.r3IPh5Ja-lkp@intel.com https://lore.kernel.org/oe-kbuild-all/202304200812.6UqNDVZy-lkp@intel.com https://lore.kernel.org/oe-kbuild-all/202304201027.2upm4i0C-lkp@intel.com https://lore.kernel.org/oe-kbuild-all/202304201216.YgbKeHUJ-lkp@intel.com https://lore.kernel.org/oe-kbuild-all/202304210303.nlMI0sRQ-lkp@intel.com https://lore.kernel.org/oe-kbuild-all/202304210349.DykCi88S-lkp@intel.com https://lore.kernel.org/oe-kbuild-all/202304210552.jAaBFgWm-lkp@intel.com Error/Warning: (recently discovered and may have been fixed) arc-elf-ld: drivers/net/phy/phy_device.c:3026: undefined reference to `devm_led_classdev_register_ext' arch/arm64/mm/fixmap.c:187:10: warning: variable 'bm_pudp' set but not used [-Wunused-but-set-variable] drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dmub_srv.c:184:19: warning: variable 'dmub' set but not used [-Wunused-but-set-variable] drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_abm.c:138:15: warning: variable 'feature_support' set but not used [-Wunused-but-set-variable] drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_abm_lcd.c:122:14: warning: no previous prototype for function 'dmub_abm_get_current_backlight' [-Wmissing-prototypes] drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_abm_lcd.c:133:14: warning: no previous prototype for function 'dmub_abm_get_target_backlight' [-Wmissing-prototypes] drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_abm_lcd.c:144:6: warning: no previous prototype for function 'dmub_abm_set_level' [-Wmissing-prototypes] drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_abm_lcd.c:163:6: warning: no previous prototype for function 'dmub_abm_set_ambient_level' [-Wmissing-prototypes] drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_abm_lcd.c:183:6: warning: no previous prototype for function 'dmub_abm_init_config' [-Wmissing-prototypes] drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_abm_lcd.c:213:6: warning: no previous prototype for function 'dmub_abm_set_pause' [-Wmissing-prototypes] drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_abm_lcd.c:231:6: warning: no previous prototype for function 'dmub_abm_set_pipe' [-Wmissing-prototypes] drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_abm_lcd.c:251:6: warning: no previous prototype for function 'dmub_abm_set_backlight_level' [-Wmissing-prototypes] drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_abm_lcd.c:81:6: warning: no previous prototype for function 'dmub_abm_init' [-Wmissing-prototypes] drivers/gpu/drm/amd/amdgpu/../display/dc/link/link_validation.c:351:13: warning: variable 'bw_needed' set but not used [-Wunused-but-set-variable] drivers/gpu/drm/amd/amdgpu/../display/dc/link/link_validation.c:352:25: warning: variable 'link' set but not used [-Wunused-but-set-variable] drivers/gpu/drm/amd/amdgpu/amdgpu_gfx.c:451:16: warning: variable 'j' set but not used [-Wunused-but-set-variable] drivers/gpu/drm/amd/amdgpu/gfx_v9_4_3.c:1072:6: warning: no previous prototype for 'gfx_v9_4_3_disable_gpa_mode' [-Wmissing-prototypes] drivers/gpu/drm/amd/amdgpu/gfx_v9_4_3.c:1072:6: warning: no previous prototype for function 'gfx_v9_4_3_disable_gpa_mode' [-Wmissing-prototypes] drivers/gpu/drm/amd/amdgpu/gfx_v9_4_3.c:48:38: warning: unused variable 'golden_settings_gc_9_4_3' [-Wunused-const-variable] drivers/net/phy/phy_device.c:3026: undefined reference to `devm_led_classdev_register_ext' drivers/phy/mediatek/phy-mtk-hdmi-mt8195.c:298:6: warning: variable 'ret' is uninitialized when used here [-Wuninitialized] drivers/virt/fsl_hypervisor.c:799:52: error: too many arguments to function call, expected 2, have 3 fs/ext4/super.c:1262:13: warning: unused variable 'i' [-Wunused-variable] fs/ext4/super.c:1262:6: warning: unused variable 'i' [-Wunused-variable] phy_device.c:(.text+0x3548): undefined reference to `devm_led_classdev_register_ext' Unverified Error/Warning (likely false positive, please contact us if interested): drivers/acpi/property.c:985 acpi_data_prop_read_single() error: potentially dereferencing uninitialized 'obj'. fs/ext4/super.c:4722 ext4_check_feature_compatibility() warn: bitwise AND condition is false here fs/ext4/verity.c:316 ext4_get_verity_descriptor_location() error: uninitialized symbol 'desc_size_disk'. sound/soc/codecs/cs35l45.c:805:9-34: WARNING: Threaded IRQ with no primary handler requested without IRQF_ONESHOT (unless it is nested IRQ) Error/Warning ids grouped by kconfigs: gcc_recent_errors |-- alpha-allyesconfig | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- alpha-randconfig-r021-20230409 | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- alpha-randconfig-r025-20230410 | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- arc-allyesconfig | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- arc-randconfig-r006-20230417 | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- arc-randconfig-r024-20230416 | |-- arc-elf-ld:drivers-net-phy-phy_device.c:undefined-reference-to-devm_led_classdev_register_ext | `-- drivers-net-phy-phy_device.c:undefined-reference-to-devm_led_classdev_register_ext |-- arc-randconfig-r043-20230420 | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- i386-allyesconfig | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- i386-randconfig-m021-20230417 | `-- drivers-acpi-property.c-acpi_data_prop_read_single()-error:potentially-dereferencing-uninitialized-obj-. |-- i386-randconfig-s001-20230417 | `-- fs-ext4-super.c:warning:unused-variable-i |-- i386-randconfig-s002-20230417 | `-- fs-ext4-super.c:warning:unused-variable-i |-- ia64-allmodconfig | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- ia64-randconfig-r023-20230410 | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- ia64-randconfig-s043-20230416 | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-dce-dmub_abm_lcd.c:sparse:sparse:cast-truncates-bits-from-constant-value-(ffff-becomes-ff) | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- loongarch-allmodconfig | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- loongarch-defconfig | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- loongarch-randconfig-r013-20230418 | `-- phy_device.c:(.text):undefined-reference-to-devm_led_classdev_register_ext |-- microblaze-buildonly-randconfig-r006-20230418 | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- microblaze-randconfig-c44-20230419 | `-- sound-soc-codecs-cs35l45.c:WARNING:Threaded-IRQ-with-no-primary-handler-requested-without-IRQF_ONESHOT-(unless-it-is-nested-IRQ) |-- mips-allmodconfig | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- mips-allyesconfig | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- mips-randconfig-m041-20230416 | |-- fs-ext4-super.c-ext4_check_feature_compatibility()-warn:bitwise-AND-condition-is-false-here | `-- fs-ext4-verity.c-ext4_get_verity_descriptor_location()-error:uninitialized-symbol-desc_size_disk-. |-- mips-randconfig-s041-20230416 | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-dce-dmub_abm_lcd.c:sparse:sparse:cast-truncates-bits-from-constant-value-(ffff-becomes-ff) | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- parisc-randconfig-r005-20230417 | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- powerpc-allmodconfig | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- riscv-allmodconfig | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- riscv-randconfig-r016-20230416 | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- s390-allyesconfig | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- s390-buildonly-randconfig-r004-20230416 | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- sparc-allyesconfig | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- sparc64-randconfig-c024-20230417 | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- sparc64-randconfig-r003-20230416 | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- x86_64-allyesconfig | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-bw_needed-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-link-link_validation.c:warning:variable-link-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-amdgpu_gfx.c:warning:variable-j-set-but-not-used | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-gfx_v9_4_3_disable_gpa_mode |-- x86_64-randconfig-a004-20230417 | `-- fs-ext4-super.c:warning:unused-variable-i |-- x86_64-randconfig-m001 | `-- drivers-acpi-property.c-acpi_data_prop_read_single()-error:potentially-dereferencing-uninitialized-obj-. `-- x86_64-randconfig-s023 `-- fs-ext4-super.c:warning:unused-variable-i clang_recent_errors |-- arm-randconfig-r002-20230417 | |-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-function-gfx_v9_4_3_disable_gpa_mode | |-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:unused-variable-golden_settings_gc_9_4_3 | `-- drivers-phy-mediatek-phy-mtk-hdmi-mt8195.c:warning:variable-ret-is-uninitialized-when-used-here |-- arm-randconfig-r026-20230409 | `-- drivers-phy-mediatek-phy-mtk-hdmi-mt8195.c:warning:variable-ret-is-uninitialized-when-used-here |-- arm64-randconfig-r001-20230418 | |-- arch-arm64-mm-fixmap.c:warning:variable-bm_pudp-set-but-not-used | `-- drivers-phy-mediatek-phy-mtk-hdmi-mt8195.c:warning:variable-ret-is-uninitialized-when-used-here |-- arm64-randconfig-r015-20230417 | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-dc_dmub_srv.c:warning:variable-dmub-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-dce-dmub_abm.c:warning:variable-feature_support-set-but-not-used | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-dce-dmub_abm_lcd.c:warning:no-previous-prototype-for-function-dmub_abm_get_current_backlight | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-dce-dmub_abm_lcd.c:warning:no-previous-prototype-for-function-dmub_abm_get_target_backlight | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-dce-dmub_abm_lcd.c:warning:no-previous-prototype-for-function-dmub_abm_init | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-dce-dmub_abm_lcd.c:warning:no-previous-prototype-for-function-dmub_abm_init_config | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-dce-dmub_abm_lcd.c:warning:no-previous-prototype-for-function-dmub_abm_set_ambient_level | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-dce-dmub_abm_lcd.c:warning:no-previous-prototype-for-function-dmub_abm_set_backlight_level | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-dce-dmub_abm_lcd.c:warning:no-previous-prototype-for-function-dmub_abm_set_level | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-dce-dmub_abm_lcd.c:warning:no-previous-prototype-for-function-dmub_abm_set_pause | |-- drivers-gpu-drm-amd-amdgpu-..-display-dc-dce-dmub_abm_lcd.c:warning:no-previous-prototype-for-function-dmub_abm_set_pipe | |-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-function-gfx_v9_4_3_disable_gpa_mode | |-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:unused-variable-golden_settings_gc_9_4_3 | `-- drivers-phy-mediatek-phy-mtk-hdmi-mt8195.c:warning:variable-ret-is-uninitialized-when-used-here |-- arm64-randconfig-r024-20230415 | |-- arch-arm64-mm-fixmap.c:warning:variable-bm_pudp-set-but-not-used | `-- drivers-phy-mediatek-phy-mtk-hdmi-mt8195.c:warning:variable-ret-is-uninitialized-when-used-here |-- hexagon-randconfig-r045-20230420 | `-- drivers-phy-mediatek-phy-mtk-hdmi-mt8195.c:warning:variable-ret-is-uninitialized-when-used-here |-- i386-randconfig-r026-20230417 | `-- fs-ext4-super.c:warning:unused-variable-i |-- mips-randconfig-r025-20230409 | |-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-function-gfx_v9_4_3_disable_gpa_mode | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:unused-variable-golden_settings_gc_9_4_3 |-- powerpc-buildonly-randconfig-r004-20230417 | `-- drivers-virt-fsl_hypervisor.c:error:too-many-arguments-to-function-call-expected-have |-- powerpc-randconfig-r032-20230420 | |-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-function-gfx_v9_4_3_disable_gpa_mode | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:unused-variable-golden_settings_gc_9_4_3 |-- s390-randconfig-r022-20230415 | |-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:no-previous-prototype-for-function-gfx_v9_4_3_disable_gpa_mode | `-- drivers-gpu-drm-amd-amdgpu-gfx_v9_4_3.c:warning:unused-variable-golden_settings_gc_9_4_3 `-- x86_64-randconfig-a012 `-- fs-ext4-super.c:warning:unused-variable-i elapsed time: 727m configs tested: 184 configs skipped: 16 tested configs: alpha allyesconfig gcc alpha defconfig gcc alpha randconfig-r013-20230416 gcc alpha randconfig-r021-20230409 gcc alpha randconfig-r021-20230417 gcc alpha randconfig-r025-20230410 gcc arc allnoconfig gcc arc allyesconfig gcc arc defconfig gcc arc randconfig-r006-20230417 gcc arc randconfig-r024-20230409 gcc arc randconfig-r025-20230417 gcc arc randconfig-r043-20230416 gcc arc randconfig-r043-20230417 gcc arc randconfig-r043-20230420 gcc arm allmodconfig gcc arm allyesconfig gcc arm buildonly-randconfig-r005-20230416 clang arm defconfig gcc arm nhk8815_defconfig gcc arm omap1_defconfig clang arm pxa_defconfig gcc arm randconfig-r002-20230416 gcc arm randconfig-r002-20230417 clang arm randconfig-r021-20230418 clang arm randconfig-r026-20230409 clang arm randconfig-r026-20230415 gcc arm randconfig-r046-20230416 clang arm randconfig-r046-20230417 gcc arm randconfig-r046-20230420 clang arm vexpress_defconfig clang arm64 allyesconfig gcc arm64 defconfig gcc arm64 randconfig-r001-20230418 clang arm64 randconfig-r004-20230417 gcc arm64 randconfig-r015-20230417 clang arm64 randconfig-r024-20230415 clang csky buildonly-randconfig-r001-20230420 gcc csky buildonly-randconfig-r004-20230420 gcc csky defconfig gcc csky randconfig-r024-20230410 gcc hexagon randconfig-r005-20230416 clang hexagon randconfig-r006-20230418 clang hexagon randconfig-r012-20230417 clang hexagon randconfig-r016-20230417 clang hexagon randconfig-r023-20230415 clang hexagon randconfig-r034-20230420 clang hexagon randconfig-r035-20230420 clang hexagon randconfig-r041-20230416 clang hexagon randconfig-r041-20230417 clang hexagon randconfig-r041-20230420 clang hexagon randconfig-r045-20230416 clang hexagon randconfig-r045-20230417 clang hexagon randconfig-r045-20230420 clang i386 allyesconfig gcc i386 debian-10.3 gcc i386 defconfig gcc i386 randconfig-a001-20230417 gcc i386 randconfig-a002-20230417 gcc i386 randconfig-a003-20230417 gcc i386 randconfig-a004-20230417 gcc i386 randconfig-a005-20230417 gcc i386 randconfig-a006-20230417 gcc i386 randconfig-a011-20230417 clang i386 randconfig-a012-20230417 clang i386 randconfig-a013-20230417 clang i386 randconfig-a014-20230417 clang i386 randconfig-a015-20230417 clang i386 randconfig-a016-20230417 clang i386 randconfig-r026-20230417 clang ia64 allmodconfig gcc ia64 buildonly-randconfig-r001-20230417 gcc ia64 buildonly-randconfig-r005-20230418 gcc ia64 defconfig gcc ia64 randconfig-r023-20230409 gcc ia64 randconfig-r023-20230410 gcc ia64 tiger_defconfig gcc loongarch allmodconfig gcc loongarch allnoconfig gcc loongarch buildonly-randconfig-r005-20230420 gcc loongarch defconfig gcc m68k allmodconfig gcc m68k buildonly-randconfig-r006-20230416 gcc m68k defconfig gcc m68k randconfig-r004-20230416 gcc m68k randconfig-r021-20230410 gcc m68k randconfig-r022-20230409 gcc microblaze buildonly-randconfig-r004-20230418 gcc microblaze buildonly-randconfig-r006-20230418 gcc microblaze randconfig-r004-20230418 gcc microblaze randconfig-r024-20230418 gcc mips allmodconfig gcc mips allyesconfig gcc mips ci20_defconfig gcc mips gpr_defconfig gcc mips maltasmvp_defconfig gcc mips randconfig-r003-20230417 clang mips randconfig-r012-20230416 clang mips randconfig-r014-20230417 gcc mips randconfig-r025-20230409 clang mips randconfig-r025-20230418 clang mips randconfig-r026-20230410 clang mips sb1250_swarm_defconfig clang nios2 buildonly-randconfig-r001-20230416 gcc nios2 defconfig gcc nios2 randconfig-r001-20230416 gcc nios2 randconfig-r003-20230418 gcc nios2 randconfig-r033-20230420 gcc openrisc randconfig-r005-20230418 gcc openrisc randconfig-r011-20230417 gcc parisc buildonly-randconfig-r003-20230416 gcc parisc defconfig gcc parisc randconfig-r005-20230417 gcc parisc64 defconfig gcc powerpc allmodconfig gcc powerpc allnoconfig gcc powerpc buildonly-randconfig-r003-20230417 clang powerpc buildonly-randconfig-r004-20230417 clang powerpc holly_defconfig gcc powerpc icon_defconfig clang powerpc makalu_defconfig gcc powerpc rainier_defconfig gcc powerpc randconfig-r022-20230410 gcc powerpc randconfig-r023-20230417 clang powerpc randconfig-r032-20230420 clang powerpc taishan_defconfig gcc riscv allmodconfig gcc riscv allnoconfig gcc riscv buildonly-randconfig-r001-20230418 gcc riscv defconfig gcc riscv randconfig-r002-20230418 clang riscv randconfig-r016-20230416 gcc riscv randconfig-r024-20230417 clang riscv randconfig-r042-20230416 gcc riscv randconfig-r042-20230417 clang riscv randconfig-r042-20230420 gcc riscv rv32_defconfig gcc s390 allmodconfig gcc s390 allyesconfig gcc s390 buildonly-randconfig-r004-20230416 gcc s390 defconfig gcc s390 randconfig-r022-20230415 clang s390 randconfig-r044-20230416 gcc s390 randconfig-r044-20230417 clang s390 randconfig-r044-20230420 gcc sh allmodconfig gcc sh apsh4ad0a_defconfig gcc sh buildonly-randconfig-r002-20230416 gcc sh buildonly-randconfig-r005-20230417 gcc sh randconfig-r011-20230416 gcc sh randconfig-r023-20230418 gcc sh randconfig-r026-20230418 gcc sh randconfig-r031-20230420 gcc sh rsk7201_defconfig gcc sh sdk7780_defconfig gcc sh sh7710voipgw_defconfig gcc sparc defconfig gcc sparc randconfig-r021-20230415 gcc sparc randconfig-r022-20230418 gcc sparc64 buildonly-randconfig-r002-20230417 gcc sparc64 buildonly-randconfig-r003-20230418 gcc sparc64 buildonly-randconfig-r003-20230420 gcc sparc64 randconfig-r003-20230416 gcc um i386_defconfig gcc um x86_64_defconfig gcc x86_64 allnoconfig gcc x86_64 allyesconfig gcc x86_64 defconfig gcc x86_64 kexec gcc x86_64 randconfig-a001-20230417 gcc x86_64 randconfig-a002-20230417 gcc x86_64 randconfig-a003-20230417 gcc x86_64 randconfig-a004-20230417 gcc x86_64 randconfig-a005-20230417 gcc x86_64 randconfig-a006-20230417 gcc x86_64 randconfig-a011 gcc x86_64 randconfig-a012 clang x86_64 randconfig-a013 gcc x86_64 randconfig-a014 clang x86_64 randconfig-a015 gcc x86_64 randconfig-a016 clang x86_64 rhel-8.3 gcc xtensa iss_defconfig gcc xtensa randconfig-r015-20230416 gcc -- 0-DAY CI Kernel Test Service https://github.com/intel/lkp-tests

1 0

[PATCH] dt-bindings: soc: qcom: Drop unneeded quotes
by Rob Herring 20 Apr '23

20 Apr '23

Cleanup bindings dropping unneeded quotes. Once all these are fixed, checking for this can be enabled in yamllint. Signed-off-by: Rob Herring <robh(a)kernel.org> --- Documentation/devicetree/bindings/soc/qcom/qcom,apr.yaml | 4 ++-- Documentation/devicetree/bindings/soc/qcom/qcom,eud.yaml | 4 ++-- Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.yaml | 4 ++-- Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml | 4 ++-- Documentation/devicetree/bindings/soc/qcom/qcom,smem.yaml | 4 ++-- Documentation/devicetree/bindings/soc/qcom/qcom,spm.yaml | 4 ++-- Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.yaml | 2 +- 7 files changed, 13 insertions(+), 13 deletions(-) diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.yaml index 6026c21736d8..dfcd41429d25 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.yaml +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/soc/qcom/qcom,apr.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/soc/qcom/qcom,apr.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Qualcomm APR/GPR (Asynchronous/Generic Packet Router) diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,eud.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,eud.yaml index c98aab209bc5..14dd29471c80 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,eud.yaml +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,eud.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/soc/qcom/qcom,eud.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/soc/qcom/qcom,eud.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Qualcomm Embedded USB Debugger diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.yaml index ab4df0205285..8a4b7ba3aaf6 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.yaml +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/soc/qcom/qcom,geni-se.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/soc/qcom/qcom,geni-se.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: GENI Serial Engine QUP Wrapper Controller diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml index 16fd67c0bd1f..abb3bfde85a8 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/soc/qcom/qcom,smd-rpm.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/soc/qcom/qcom,smd-rpm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Qualcomm Resource Power Manager (RPM) over SMD/GLINK diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smem.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,smem.yaml index 497614ddf005..bc7815d985e4 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,smem.yaml +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smem.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/soc/qcom/qcom,smem.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/soc/qcom/qcom,smem.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Qualcomm Shared Memory Manager diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,spm.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,spm.yaml index aca3d40bcccb..20c8cd38ff0d 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,spm.yaml +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,spm.yaml @@ -1,8 +1,8 @@ # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2 --- -$id: "http://devicetree.org/schemas/soc/qcom/qcom,spm.yaml#" -$schema: "http://devicetree.org/meta-schemas/core.yaml#" +$id: http://devicetree.org/schemas/soc/qcom/qcom,spm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# title: Qualcomm Subsystem Power Manager diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.yaml index 0e6fd57d658d..74bb92e31554 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.yaml +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.yaml @@ -20,7 +20,7 @@ properties: firmware-name: $ref: /schemas/types.yaml#/definitions/string - default: "wlan/prima/WCNSS_qcom_wlan_nv.bin" + default: wlan/prima/WCNSS_qcom_wlan_nv.bin description: Relative firmware image path for the WLAN NV blob. -- 2.39.2

2 2

[PATCH] ASoC: amd: ps: Update copyright notice
by Carlos Bilbao 20 Apr '23

20 Apr '23

The most recent changes to ASoC, such as new module parameters, date to the year 2023. Update copyright statement accordingly. Signed-off-by: Carlos Bilbao <carlos.bilbao(a)amd.com> --- sound/soc/amd/ps/acp63.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/amd/ps/acp63.h b/sound/soc/amd/ps/acp63.h index 5e7f9c1c1b0e..587c206114a6 100644 --- a/sound/soc/amd/ps/acp63.h +++ b/sound/soc/amd/ps/acp63.h @@ -2,7 +2,7 @@ /* * AMD ALSA SoC PDM Driver * - * Copyright (C) 2022 Advanced Micro Devices, Inc. All rights reserved. + * Copyright (C) 2022, 2023 Advanced Micro Devices, Inc. All rights reserved. */ #include <sound/acp63_chip_offset_byte.h> -- 2.34.1

1 0

[PATCH v2] docs: sound/kernel-api/writing-an-alsa-driver.rst: polishing
by Oswald Buddenhagen 20 Apr '23

20 Apr '23

- Update some outdated info - Language fixes - Whitespace/formatting fixes - Prefer attached over stand-alone '::' Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- v2: - dropped questionable hunk from period timer example code - new hunk: improved wording wrt period sizes --- Range-diff against v1: 1: d9eb90fe56ae ! 1: 0f0ea8a17ff1 docs: sound: kernel-api: writing-an-alsa-driver.rst: polishing @@ Metadata Author: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> ## Commit message ## - docs: sound: kernel-api: writing-an-alsa-driver.rst: polishing + docs: sound/kernel-api/writing-an-alsa-driver.rst: polishing - Update some outdated info - Language fixes - Whitespace/formatting fixes - Prefer attached over stand-alone '::' Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> + --- + + v2: + - dropped questionable hunk from period timer example code + - new hunk: improved wording wrt period sizes + ## Documentation/sound/kernel-api/writing-an-alsa-driver.rst ## @@ Documentation/sound/kernel-api/writing-an-alsa-driver.rst: explain the general topic of linux kernel coding and doesn't cover low-level driver implementation details. It only describes the standard @@ Documentation/sound/kernel-api/writing-an-alsa-driver.rst: Typically, you'll hav - world. The period defines the size at which a PCM interrupt is - generated. This size strongly depends on the hardware. Generally, - the smaller period size will give you more interrupts, that is, +- more controls. In the case of capture, this size defines the input +- latency. On the other hand, the whole buffer size defines the +- output latency for the playback direction. + world. The period defines the point at which a PCM interrupt is + generated. This point strongly depends on the hardware. Generally, -+ a smaller period size will give you more interrupts, that is, - more controls. In the case of capture, this size defines the input - latency. On the other hand, the whole buffer size defines the - output latency for the playback direction. ++ a smaller period size will give you more interrupts, which results ++ in being able to fill/drain the buffer more timely. In the case of ++ capture, this size defines the input latency. On the other hand, ++ the whole buffer size defines the output latency for the playback ++ direction. - There is also a field ``fifo_size``. This specifies the size of the - hardware FIFO, but currently it is neither used in the driver nor @@ Documentation/sound/kernel-api/writing-an-alsa-driver.rst: position and accumula static irqreturn_t snd_mychip_interrupt(int irq, void *dev_id) -@@ Documentation/sound/kernel-api/writing-an-alsa-driver.rst: Typical code would be like the following. - /* over the period boundary? */ - if (chip->size >= runtime->period_size) { - /* reset the accumulator */ -- chip->size %= runtime->period_size; -+ chip->size -= runtime->period_size; - /* call updater */ - spin_unlock(&chip->lock); - snd_pcm_period_elapsed(substream); @@ Documentation/sound/kernel-api/writing-an-alsa-driver.rst: Typical code would be like the following. On calling :c:func:`snd_pcm_period_elapsed()` ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ .../kernel-api/writing-an-alsa-driver.rst | 1052 +++++++---------- 1 file changed, 399 insertions(+), 653 deletions(-) diff --git a/Documentation/sound/kernel-api/writing-an-alsa-driver.rst b/Documentation/sound/kernel-api/writing-an-alsa-driver.rst index a368529e8ed3..a22fa9642011 100644 --- a/Documentation/sound/kernel-api/writing-an-alsa-driver.rst +++ b/Documentation/sound/kernel-api/writing-an-alsa-driver.rst @@ -19,18 +19,13 @@ explain the general topic of linux kernel coding and doesn't cover low-level driver implementation details. It only describes the standard way to write a PCI sound driver on ALSA. -This document is still a draft version. Any feedback and corrections, -please!! - File Tree Structure =================== General ------- -The file tree structure of ALSA driver is depicted below. - -:: +The file tree structure of ALSA driver is depicted below:: sound /core @@ -68,39 +63,39 @@ kernel config. core/oss ~~~~~~~~ -The codes for PCM and mixer OSS emulation modules are stored in this -directory. The rawmidi OSS emulation is included in the ALSA rawmidi +The code for OSS PCM and mixer emulation modules is stored in this +directory. The OSS rawmidi emulation is included in the ALSA rawmidi code since it's quite small. The sequencer code is stored in ``core/seq/oss`` directory (see `below <core/seq/oss_>`__). core/seq ~~~~~~~~ This directory and its sub-directories are for the ALSA sequencer. This directory contains the sequencer core and primary sequencer modules such -like snd-seq-midi, snd-seq-virmidi, etc. They are compiled only when +as snd-seq-midi, snd-seq-virmidi, etc. They are compiled only when ``CONFIG_SND_SEQUENCER`` is set in the kernel config. core/seq/oss ~~~~~~~~~~~~ -This contains the OSS sequencer emulation codes. +This contains the OSS sequencer emulation code. include directory ----------------- This is the place for the public header files of ALSA drivers, which are -to be exported to user-space, or included by several files at different +to be exported to user-space, or included by several files in different directories. Basically, the private header files should not be placed in this directory, but you may still find files there, due to historical reasons :) drivers directory ----------------- This directory contains code shared among different drivers on different architectures. They are hence supposed not to be architecture-specific. -For example, the dummy pcm driver and the serial MIDI driver are found +For example, the dummy PCM driver and the serial MIDI driver are found in this directory. In the sub-directories, there is code for components which are independent from bus and cpu architectures. @@ -156,8 +151,8 @@ these architectures. usb directory ------------- -This directory contains the USB-audio driver. In the latest version, the -USB MIDI driver is integrated in the usb-audio driver. +This directory contains the USB-audio driver. +The USB MIDI driver is integrated in the usb-audio driver. pcmcia directory ---------------- @@ -175,9 +170,9 @@ layer including ASoC core, codec and machine drivers. oss directory ------------- -Here contains OSS/Lite codes. -All codes have been deprecated except for dmasound on m68k as of -writing this. +This contains OSS/Lite code. +At the time of writing, all code has been removed except for dmasound +on m68k. Basic Flow for PCI Drivers @@ -341,7 +336,7 @@ to details explained in the following section. error: snd_card_free(card); - return err; + return err; } /* destructor -- see the "Destructor" sub-section */ @@ -381,7 +376,7 @@ where ``enable[dev]`` is the module option. Each time the ``probe`` callback is called, check the availability of the device. If not available, simply increment the device index and -returns. dev will be incremented also later (`step 7 +return. dev will be incremented also later (`step 7 <7) Set the PCI driver data and return zero._>`__). 2) Create a card instance @@ -402,9 +397,7 @@ Components`_. 3) Create a main component ~~~~~~~~~~~~~~~~~~~~~~~~~~ -In this part, the PCI resources are allocated. - -:: +In this part, the PCI resources are allocated:: struct mychip *chip; .... @@ -417,13 +410,11 @@ Management`_. When something goes wrong, the probe function needs to deal with the error. In this example, we have a single error handling path placed -at the end of the function. - -:: +at the end of the function:: error: snd_card_free(card); - return err; + return err; Since each component can be properly freed, the single :c:func:`snd_card_free()` call should suffice in most cases. @@ -483,13 +474,11 @@ remove callback and power-management callbacks, too. Destructor ---------- -The destructor, remove callback, simply releases the card instance. Then -the ALSA middle layer will release all the attached components +The destructor, the remove callback, simply releases the card instance. +Then the ALSA middle layer will release all the attached components automatically. -It would be typically just calling :c:func:`snd_card_free()`: - -:: +It would be typically just calling :c:func:`snd_card_free()`:: static void snd_mychip_remove(struct pci_dev *pci) { @@ -504,9 +493,7 @@ Header Files ------------ For the above example, at least the following include files are -necessary. - -:: +necessary:: #include <linux/init.h> #include <linux/pci.h> @@ -544,9 +531,7 @@ list on the card record is used to manage the correct release of resources at destruction. As mentioned above, to create a card instance, call -:c:func:`snd_card_new()`. - -:: +:c:func:`snd_card_new()`:: struct snd_card *card; int err; @@ -572,10 +557,8 @@ struct snd_device object. A component can be a PCM instance, a control interface, a raw MIDI interface, etc. Each such instance has one component entry. -A component can be created via :c:func:`snd_device_new()` -function. - -:: +A component can be created via the :c:func:`snd_device_new()` +function:: snd_device_new(card, SNDRV_DEV_XXX, chip, &ops); @@ -591,7 +574,7 @@ allocated manually beforehand, and its pointer is passed as the argument. This pointer (``chip`` in the above example) is used as the identifier for the instance. -Each pre-defined ALSA component such as ac97 and pcm calls +Each pre-defined ALSA component such as AC97 and PCM calls :c:func:`snd_device_new()` inside its constructor. The destructor for each component is defined in the callback pointers. Hence, you don't need to take care of calling a destructor for such a component. @@ -605,9 +588,7 @@ Chip-Specific Data ------------------ Chip-specific information, e.g. the I/O port address, its resource -pointer, or the irq number, is stored in the chip-specific record. - -:: +pointer, or the irq number, is stored in the chip-specific record:: struct mychip { .... @@ -620,9 +601,7 @@ In general, there are two ways of allocating the chip record. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ As mentioned above, you can pass the extra-data-length to the 5th -argument of :c:func:`snd_card_new()`, i.e. - -:: +argument of :c:func:`snd_card_new()`, e.g.:: err = snd_card_new(&pci->dev, index[dev], id[dev], THIS_MODULE, sizeof(struct mychip), &card); @@ -642,9 +621,7 @@ released together with the card instance. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ After allocating a card instance via :c:func:`snd_card_new()` -(with ``0`` on the 4th arg), call :c:func:`kzalloc()`. - -:: +(with ``0`` on the 4th arg), call :c:func:`kzalloc()`:: struct snd_card *card; struct mychip *chip; @@ -663,39 +640,33 @@ The chip record should have the field to hold the card pointer at least, }; -Then, set the card pointer in the returned chip instance. - -:: +Then, set the card pointer in the returned chip instance:: chip->card = card; Next, initialize the fields, and register this chip record as a -low-level device with a specified ``ops``, - -:: +low-level device with a specified ``ops``:: static const struct snd_device_ops ops = { .dev_free = snd_mychip_dev_free, }; .... snd_device_new(card, SNDRV_DEV_LOWLEVEL, chip, &ops); :c:func:`snd_mychip_dev_free()` is the device-destructor -function, which will call the real destructor. - -:: +function, which will call the real destructor:: static int snd_mychip_dev_free(struct snd_device *device) { return snd_mychip_free(device->device_data); } where :c:func:`snd_mychip_free()` is the real destructor. -The demerit of this method is the obviously more amount of codes. -The merit is, however, you can trigger the own callback at registering -and disconnecting the card via setting in snd_device_ops. -About the registering and disconnecting the card, see the subsections +The demerit of this method is the obviously larger amount of code. +The merit is, however, that you can trigger your own callback at +registering and disconnecting the card via a setting in snd_device_ops. +About registering and disconnecting the card, see the subsections below. @@ -724,9 +695,7 @@ Full Code Example ----------------- In this section, we'll complete the chip-specific constructor, -destructor and PCI entries. Example code is shown first, below. - -:: +destructor and PCI entries. Example code is shown first, below:: struct mychip { struct snd_card *card; @@ -866,9 +835,7 @@ resources. Also, you need to set the proper PCI DMA mask to limit the accessed I/O range. In some cases, you might need to call :c:func:`pci_set_master()` function, too. -Suppose the 28bit mask, and the code to be added would be like: - -:: +Suppose a 28bit mask, the code to be added would look like:: err = pci_enable_device(pci); if (err < 0) @@ -890,9 +857,7 @@ function (see below). Now assume that the PCI device has an I/O port with 8 bytes and an interrupt. Then struct mychip will have the -following fields: - -:: +following fields:: struct mychip { struct snd_card *card; @@ -905,14 +870,12 @@ following fields: For an I/O port (and also a memory region), you need to have the resource pointer for the standard resource management. For an irq, you have to keep only the irq number (integer). But you need to initialize -this number as -1 before actual allocation, since irq 0 is valid. The +this number to -1 before actual allocation, since irq 0 is valid. The port address and its resource pointer can be initialized as null by :c:func:`kzalloc()` automatically, so you don't have to take care of resetting them. -The allocation of an I/O port is done like this: - -:: +The allocation of an I/O port is done like this:: err = pci_request_regions(pci, "My Chip"); if (err < 0) { @@ -928,9 +891,7 @@ The returned value, ``chip->res_port``, is allocated via must be released via :c:func:`kfree()`, but there is a problem with this. This issue will be explained later. -The allocation of an interrupt source is done like this: - -:: +The allocation of an interrupt source is done like this:: if (request_irq(pci->irq, snd_mychip_interrupt, IRQF_SHARED, KBUILD_MODNAME, chip)) { @@ -954,36 +915,31 @@ used for that, but you can use what you like, too. I won't give details about the interrupt handler at this point, but at least its appearance can be explained now. The interrupt handler looks -usually like the following: - -:: +usually as follows:: static irqreturn_t snd_mychip_interrupt(int irq, void *dev_id) { struct mychip *chip = dev_id; .... return IRQ_HANDLED; } After requesting the IRQ, you can passed it to ``card->sync_irq`` -field: -:: +field:: card->irq = chip->irq; -This allows PCM core automatically performing -:c:func:`synchronize_irq()` at the necessary timing like ``hw_free``. +This allows the PCM core to automatically call +:c:func:`synchronize_irq()` at the right time, like before ``hw_free``. See the later section `sync_stop callback`_ for details. Now let's write the corresponding destructor for the resources above. The role of destructor is simple: disable the hardware (if already activated) and release the resources. So far, we have no hardware part, so the disabling code is not written here. To release the resources, the “check-and-release” method is a safer way. -For the interrupt, do like this: - -:: +For the interrupt, do like this:: if (chip->irq >= 0) free_irq(chip->irq, chip); @@ -997,72 +953,59 @@ When you requested I/O ports or memory regions via :c:func:`pci_request_regions()` like in this example, release the resource(s) using the corresponding function, :c:func:`pci_release_region()` or -:c:func:`pci_release_regions()`. - -:: +:c:func:`pci_release_regions()`:: pci_release_regions(chip->pci); When you requested manually via :c:func:`request_region()` or :c:func:`request_mem_region()`, you can release it via :c:func:`release_resource()`. Suppose that you keep the resource pointer returned from :c:func:`request_region()` in -chip->res_port, the release procedure looks like: - -:: +chip->res_port, the release procedure looks like:: release_and_free_resource(chip->res_port); Don't forget to call :c:func:`pci_disable_device()` before the end. -And finally, release the chip-specific record. - -:: +And finally, release the chip-specific record:: kfree(chip); -We didn't implement the hardware disabling part in the above. If you +We didn't implement the hardware disabling part above. If you need to do this, please note that the destructor may be called even before the initialization of the chip is completed. It would be better to have a flag to skip hardware disabling if the hardware was not initialized yet. When the chip-data is assigned to the card using -:c:func:`snd_device_new()` with ``SNDRV_DEV_LOWLELVEL`` , its -destructor is called at the last. That is, it is assured that all other +:c:func:`snd_device_new()` with ``SNDRV_DEV_LOWLELVEL``, its +destructor is called last. That is, it is assured that all other components like PCMs and controls have already been released. You don't have to stop PCMs, etc. explicitly, but just call low-level hardware stopping. The management of a memory-mapped region is almost as same as the -management of an I/O port. You'll need three fields like the -following: - -:: +management of an I/O port. You'll need two fields as follows:: struct mychip { .... unsigned long iobase_phys; void __iomem *iobase_virt; }; -and the allocation would be like below: - -:: +and the allocation would look like below:: err = pci_request_regions(pci, "My Chip"); if (err < 0) { kfree(chip); return err; } chip->iobase_phys = pci_resource_start(pci, 0); chip->iobase_virt = ioremap(chip->iobase_phys, pci_resource_len(pci, 0)); -and the corresponding destructor would be: - -:: +and the corresponding destructor would be:: static int snd_mychip_free(struct mychip *chip) { @@ -1075,9 +1018,7 @@ and the corresponding destructor would be: } Of course, a modern way with :c:func:`pci_iomap()` will make things a -bit easier, too. - -:: +bit easier, too:: err = pci_request_regions(pci, "My Chip"); if (err < 0) { @@ -1097,9 +1038,7 @@ struct pci_device_id table for this chipset. It's a table of PCI vendor/device ID number, and some masks. -For example, - -:: +For example:: static struct pci_device_id snd_mychip_ids[] = { { PCI_VENDOR_ID_FOO, PCI_DEVICE_ID_BAR, @@ -1120,24 +1059,20 @@ The last entry of this list is the terminator. You must specify this all-zero entry. Then, prepare the struct pci_driver -record: - -:: +record:: static struct pci_driver driver = { .name = KBUILD_MODNAME, .id_table = snd_mychip_ids, .probe = snd_mychip_probe, .remove = snd_mychip_remove, }; The ``probe`` and ``remove`` functions have already been defined in the previous sections. The ``name`` field is the name string of this -device. Note that you must not use a slash “/” in this string. +device. Note that you must not use slashes (“/”) in this string. -And at last, the module entries: - -:: +And at last, the module entries:: static int __init alsa_card_mychip_init(void) { @@ -1167,33 +1102,31 @@ The PCM middle layer of ALSA is quite powerful and it is only necessary for each driver to implement the low-level functions to access its hardware. -For accessing to the PCM layer, you need to include ``<sound/pcm.h>`` +To access the PCM layer, you need to include ``<sound/pcm.h>`` first. In addition, ``<sound/pcm_params.h>`` might be needed if you -access to some functions related with hw_param. +access some functions related with hw_param. -Each card device can have up to four pcm instances. A pcm instance -corresponds to a pcm device file. The limitation of number of instances -comes only from the available bit size of the Linux's device numbers. -Once when 64bit device number is used, we'll have more pcm instances +Each card device can have up to four PCM instances. A PCM instance +corresponds to a PCM device file. The limitation of number of instances +comes only from the available bit size of Linux' device numbers. +Once 64bit device numbers are used, we'll have more PCM instances available. -A pcm instance consists of pcm playback and capture streams, and each -pcm stream consists of one or more pcm substreams. Some soundcards +A PCM instance consists of PCM playback and capture streams, and each +PCM stream consists of one or more PCM substreams. Some soundcards support multiple playback functions. For example, emu10k1 has a PCM playback of 32 stereo substreams. In this case, at each open, a free substream is (usually) automatically chosen and opened. Meanwhile, when -only one substream exists and it was already opened, the successful open +only one substream exists and it was already opened, a subsequent open will either block or error with ``EAGAIN`` according to the file open mode. But you don't have to care about such details in your driver. The PCM middle layer will take care of such work. Full Code Example ----------------- The example code below does not include any hardware access routines but -shows only the skeleton, how to build up the PCM interfaces. - -:: +shows only the skeleton, how to build up the PCM interfaces:: #include <sound/pcm.h> .... @@ -1399,10 +1332,8 @@ shows only the skeleton, how to build up the PCM interfaces. PCM Constructor --------------- -A pcm instance is allocated by the :c:func:`snd_pcm_new()` -function. It would be better to create a constructor for pcm, namely, - -:: +A PCM instance is allocated by the :c:func:`snd_pcm_new()` +function. It would be better to create a constructor for the PCM, namely:: static int snd_mychip_new_pcm(struct mychip *chip) { @@ -1415,16 +1346,16 @@ function. It would be better to create a constructor for pcm, namely, pcm->private_data = chip; strcpy(pcm->name, "My Chip"); chip->pcm = pcm; - .... + ... return 0; } -The :c:func:`snd_pcm_new()` function takes four arguments. The -first argument is the card pointer to which this pcm is assigned, and +The :c:func:`snd_pcm_new()` function takes six arguments. The +first argument is the card pointer to which this PCM is assigned, and the second is the ID string. The third argument (``index``, 0 in the above) is the index of this new -pcm. It begins from zero. If you create more than one pcm instances, +PCM. It begins from zero. If you create more than one PCM instances, specify the different numbers in this argument. For example, ``index = 1`` for the second PCM device. @@ -1437,26 +1368,20 @@ If a chip supports multiple playbacks or captures, you can specify more numbers, but they must be handled properly in open/close, etc. callbacks. When you need to know which substream you are referring to, then it can be obtained from struct snd_pcm_substream data passed to each -callback as follows: - -:: +callback as follows:: struct snd_pcm_substream *substream; int index = substream->number; -After the pcm is created, you need to set operators for each pcm stream. - -:: +After the PCM is created, you need to set operators for each PCM stream:: snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_PLAYBACK, &snd_mychip_playback_ops); snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_CAPTURE, &snd_mychip_capture_ops); -The operators are defined typically like this: - -:: +The operators are defined typically like this:: static struct snd_pcm_ops snd_mychip_playback_ops = { .open = snd_mychip_pcm_open, @@ -1472,41 +1397,35 @@ All the callbacks are described in the Operators_ subsection. After setting the operators, you probably will want to pre-allocate the buffer and set up the managed allocation mode. -For that, simply call the following: - -:: +For that, simply call the following:: snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_DEV, &chip->pci->dev, 64*1024, 64*1024); -It will allocate a buffer up to 64kB as default. Buffer management +It will allocate a buffer up to 64kB by default. Buffer management details will be described in the later section `Buffer and Memory Management`_. -Additionally, you can set some extra information for this pcm in +Additionally, you can set some extra information for this PCM in ``pcm->info_flags``. The available values are defined as ``SNDRV_PCM_INFO_XXX`` in ``<sound/asound.h>``, which is used for the hardware definition (described later). When your soundchip supports only -half-duplex, specify like this: - -:: +half-duplex, specify it like this:: pcm->info_flags = SNDRV_PCM_INFO_HALF_DUPLEX; ... And the Destructor? ----------------------- -The destructor for a pcm instance is not always necessary. Since the pcm +The destructor for a PCM instance is not always necessary. Since the PCM device will be released by the middle layer code automatically, you don't have to call the destructor explicitly. The destructor would be necessary if you created special records internally and needed to release them. In such a case, set the -destructor function to ``pcm->private_free``: - -:: +destructor function to ``pcm->private_free``:: static void mychip_pcm_free(struct snd_pcm *pcm) { @@ -1537,13 +1456,11 @@ Runtime Pointer - The Chest of PCM Information When the PCM substream is opened, a PCM runtime instance is allocated and assigned to the substream. This pointer is accessible via ``substream->runtime``. This runtime pointer holds most information you -need to control the PCM: the copy of hw_params and sw_params +need to control the PCM: a copy of hw_params and sw_params configurations, the buffer pointers, mmap records, spinlocks, etc. The definition of runtime instance is found in ``<sound/pcm.h>``. Here -are the contents of this file: - -:: +is the relevant part of this file:: struct _snd_pcm_runtime { /* -- Status -- */ @@ -1638,24 +1555,20 @@ Hardware Description The hardware descriptor (struct snd_pcm_hardware) contains the definitions of the fundamental hardware configuration. Above all, you'll need to define this -in the `PCM open callback`_. Note that the runtime instance holds the copy of -the descriptor, not the pointer to the existing descriptor. That is, +in the `PCM open callback`_. Note that the runtime instance holds a copy of +the descriptor, not a pointer to the existing descriptor. That is, in the open callback, you can modify the copied descriptor (``runtime->hw``) as you need. For example, if the maximum number of channels is 1 only on some chip models, you can still use the same -hardware descriptor and change the channels_max later: - -:: +hardware descriptor and change the channels_max later:: struct snd_pcm_runtime *runtime = substream->runtime; ... runtime->hw = snd_mychip_playback_hw; /* common definition */ if (chip->model == VERY_OLD_ONE) runtime->hw.channels_max = 1; -Typically, you'll have a hardware descriptor as below: - -:: +Typically, you'll have a hardware descriptor as below:: static struct snd_pcm_hardware snd_mychip_playback_hw = { .info = (SNDRV_PCM_INFO_MMAP | @@ -1676,71 +1589,72 @@ Typically, you'll have a hardware descriptor as below: }; - The ``info`` field contains the type and capabilities of this - pcm. The bit flags are defined in ``<sound/asound.h>`` as + PCM. The bit flags are defined in ``<sound/asound.h>`` as ``SNDRV_PCM_INFO_XXX``. Here, at least, you have to specify whether - the mmap is supported and which interleaved format is + mmap is supported and which interleaving formats are supported. When the hardware supports mmap, add the ``SNDRV_PCM_INFO_MMAP`` flag here. When the hardware supports the - interleaved or the non-interleaved formats, + interleaved or the non-interleaved formats, the ``SNDRV_PCM_INFO_INTERLEAVED`` or ``SNDRV_PCM_INFO_NONINTERLEAVED`` flag must be set, respectively. If both are supported, you can set both, too. In the above example, ``MMAP_VALID`` and ``BLOCK_TRANSFER`` are specified for the OSS mmap mode. Usually both are set. Of course, - ``MMAP_VALID`` is set only if the mmap is really supported. + ``MMAP_VALID`` is set only if mmap is really supported. The other possible flags are ``SNDRV_PCM_INFO_PAUSE`` and - ``SNDRV_PCM_INFO_RESUME``. The ``PAUSE`` bit means that the pcm + ``SNDRV_PCM_INFO_RESUME``. The ``PAUSE`` bit means that the PCM supports the “pause” operation, while the ``RESUME`` bit means that - the pcm supports the full “suspend/resume” operation. If the + the PCM supports the full “suspend/resume” operation. If the ``PAUSE`` flag is set, the ``trigger`` callback below must handle the corresponding (pause push/release) commands. The suspend/resume trigger commands can be defined even without the ``RESUME`` - flag. See `Power Management`_ section for details. + flag. See the `Power Management`_ section for details. When the PCM substreams can be synchronized (typically, - synchronized start/stop of a playback and a capture streams), you + synchronized start/stop of a playback and a capture stream), you can give ``SNDRV_PCM_INFO_SYNC_START``, too. In this case, you'll need to check the linked-list of PCM substreams in the trigger - callback. This will be described in the later section. + callback. This will be described in a later section. -- ``formats`` field contains the bit-flags of supported formats +- The ``formats`` field contains the bit-flags of supported formats (``SNDRV_PCM_FMTBIT_XXX``). If the hardware supports more than one format, give all or'ed bits. In the example above, the signed 16bit little-endian format is specified. -- ``rates`` field contains the bit-flags of supported rates +- The ``rates`` field contains the bit-flags of supported rates (``SNDRV_PCM_RATE_XXX``). When the chip supports continuous rates, - pass ``CONTINUOUS`` bit additionally. The pre-defined rate bits are - provided only for typical rates. If your chip supports + pass the ``CONTINUOUS`` bit additionally. The pre-defined rate bits + are provided only for typical rates. If your chip supports unconventional rates, you need to add the ``KNOT`` bit and set up the hardware constraint manually (explained later). - ``rate_min`` and ``rate_max`` define the minimum and maximum sample rate. This should correspond somehow to ``rates`` bits. -- ``channels_min`` and ``channels_max`` define, as you might already +- ``channels_min`` and ``channels_max`` define, as you might have already expected, the minimum and maximum number of channels. - ``buffer_bytes_max`` defines the maximum buffer size in bytes. There is no ``buffer_bytes_min`` field, since it can be calculated from the minimum period size and the minimum number of periods. Meanwhile, ``period_bytes_min`` and ``period_bytes_max`` define the minimum and maximum size of the period in bytes. ``periods_max`` and ``periods_min`` define the maximum and minimum number of periods in the buffer. The “period” is a term that corresponds to a fragment in the OSS - world. The period defines the size at which a PCM interrupt is - generated. This size strongly depends on the hardware. Generally, - the smaller period size will give you more interrupts, that is, - more controls. In the case of capture, this size defines the input - latency. On the other hand, the whole buffer size defines the - output latency for the playback direction. + world. The period defines the point at which a PCM interrupt is + generated. This point strongly depends on the hardware. Generally, + a smaller period size will give you more interrupts, which results + in being able to fill/drain the buffer more timely. In the case of + capture, this size defines the input latency. On the other hand, + the whole buffer size defines the output latency for the playback + direction. - There is also a field ``fifo_size``. This specifies the size of the - hardware FIFO, but currently it is neither used in the driver nor + hardware FIFO, but currently it is neither used by the drivers nor in the alsa-lib. So, you can ignore this field. PCM Configurations @@ -1759,63 +1673,60 @@ One thing to be noted is that the configured buffer and period sizes are stored in “frames” in the runtime. In the ALSA world, ``1 frame = channels \* samples-size``. For conversion between frames and bytes, you can use the :c:func:`frames_to_bytes()` and -:c:func:`bytes_to_frames()` helper functions. - -:: +:c:func:`bytes_to_frames()` helper functions:: period_bytes = frames_to_bytes(runtime, runtime->period_size); Also, many software parameters (sw_params) are stored in frames, too. -Please check the type of the field. ``snd_pcm_uframes_t`` is for the -frames as unsigned integer while ``snd_pcm_sframes_t`` is for the +Please check the type of the field. ``snd_pcm_uframes_t`` is for +frames as unsigned integer while ``snd_pcm_sframes_t`` is for frames as signed integer. DMA Buffer Information ~~~~~~~~~~~~~~~~~~~~~~ -The DMA buffer is defined by the following four fields, ``dma_area``, -``dma_addr``, ``dma_bytes`` and ``dma_private``. The ``dma_area`` +The DMA buffer is defined by the following four fields: ``dma_area``, +``dma_addr``, ``dma_bytes`` and ``dma_private``. ``dma_area`` holds the buffer pointer (the logical address). You can call :c:func:`memcpy()` from/to this pointer. Meanwhile, ``dma_addr`` holds the physical address of the buffer. This field is specified only when -the buffer is a linear buffer. ``dma_bytes`` holds the size of buffer -in bytes. ``dma_private`` is used for the ALSA DMA allocator. +the buffer is a linear buffer. ``dma_bytes`` holds the size of the +buffer in bytes. ``dma_private`` is used for the ALSA DMA allocator. If you use either the managed buffer allocation mode or the standard API function :c:func:`snd_pcm_lib_malloc_pages()` for allocating the buffer, these fields are set by the ALSA middle layer, and you should *not* change them by yourself. You can read them but not write them. On the other hand, if you want to allocate the buffer by yourself, you'll -need to manage it in hw_params callback. At least, ``dma_bytes`` is +need to manage it in the hw_params callback. At least, ``dma_bytes`` is mandatory. ``dma_area`` is necessary when the buffer is mmapped. If your driver doesn't support mmap, this field is not necessary. ``dma_addr`` is also optional. You can use dma_private as you like, too. Running Status ~~~~~~~~~~~~~~ The running status can be referred via ``runtime->status``. This is -the pointer to the struct snd_pcm_mmap_status record. +a pointer to a struct snd_pcm_mmap_status record. For example, you can get the current DMA hardware pointer via ``runtime->status->hw_ptr``. The DMA application pointer can be referred via ``runtime->control``, -which points to the struct snd_pcm_mmap_control record. -However, accessing directly to this value is not recommended. +which points to a struct snd_pcm_mmap_control record. +However, accessing this value directly is not recommended. Private Data ~~~~~~~~~~~~ You can allocate a record for the substream and store it in ``runtime->private_data``. Usually, this is done in the `PCM open callback`_. Don't mix this with ``pcm->private_data``. The ``pcm->private_data`` usually points to the chip instance assigned -statically at the creation of PCM, while the ``runtime->private_data`` -points to a dynamic data structure created at the PCM open -callback. - -:: +statically at creation time of the PCM device, while +``runtime->private_data`` +points to a dynamic data structure created in the PCM open +callback:: static int snd_xxx_open(struct snd_pcm_substream *substream) { @@ -1832,20 +1743,18 @@ The allocated object must be released in the `close callback`_. Operators --------- -OK, now let me give details about each pcm callback (``ops``). In +OK, now let me give details about each PCM callback (``ops``). In general, every callback must return 0 if successful, or a negative error number such as ``-EINVAL``. To choose an appropriate error number, it is advised to check what value other parts of the kernel return when the same kind of request fails. -The callback function takes at least the argument with +Each callback function takes at least one argument containing a struct snd_pcm_substream pointer. To retrieve the chip record from the given substream instance, you can use the following -macro. +macro:: -:: - - int xxx() { + int xxx(...) { struct mychip *chip = snd_pcm_substream_chip(substream); .... } @@ -1864,12 +1773,10 @@ PCM open callback static int snd_xxx_open(struct snd_pcm_substream *substream); -This is called when a pcm substream is opened. +This is called when a PCM substream is opened. At least, here you have to initialize the ``runtime->hw`` -record. Typically, this is done by like this: - -:: +record. Typically, this is done like this:: static int snd_xxx_open(struct snd_pcm_substream *substream) { @@ -1883,7 +1790,7 @@ record. Typically, this is done by like this: where ``snd_mychip_playback_hw`` is the pre-defined hardware description. -You can allocate a private data in this callback, as described in +You can allocate private data in this callback, as described in the `Private Data`_ section. If the hardware configuration needs more constraints, set the hardware @@ -1897,73 +1804,69 @@ close callback static int snd_xxx_close(struct snd_pcm_substream *substream); -Obviously, this is called when a pcm substream is closed. +Obviously, this is called when a PCM substream is closed. -Any private instance for a pcm substream allocated in the ``open`` -callback will be released here. - -:: +Any private instance for a PCM substream allocated in the ``open`` +callback will be released here:: static int snd_xxx_close(struct snd_pcm_substream *substream) { .... kfree(substream->runtime->private_data); .... } ioctl callback ~~~~~~~~~~~~~~ -This is used for any special call to pcm ioctls. But usually you can -leave it as NULL, then PCM core calls the generic ioctl callback -function :c:func:`snd_pcm_lib_ioctl()`. If you need to deal with the +This is used for any special call to PCM ioctls. But usually you can +leave it NULL, then the PCM core calls the generic ioctl callback +function :c:func:`snd_pcm_lib_ioctl()`. If you need to deal with a unique setup of channel info or reset procedure, you can pass your own callback function here. hw_params callback ~~~~~~~~~~~~~~~~~~~ :: static int snd_xxx_hw_params(struct snd_pcm_substream *substream, struct snd_pcm_hw_params *hw_params); -This is called when the hardware parameter (``hw_params``) is set up +This is called when the hardware parameters (``hw_params``) are set up by the application, that is, once when the buffer size, the period -size, the format, etc. are defined for the pcm substream. +size, the format, etc. are defined for the PCM substream. Many hardware setups should be done in this callback, including the allocation of buffers. -Parameters to be initialized are retrieved by +Parameters to be initialized are retrieved by the :c:func:`params_xxx()` macros. -When you set up the managed buffer allocation mode for the substream, +When you choose managed buffer allocation mode for the substream, a buffer is already allocated before this callback gets called. Alternatively, you can call a helper function below for -allocating the buffer, too. - -:: +allocating the buffer:: snd_pcm_lib_malloc_pages(substream, params_buffer_bytes(hw_params)); :c:func:`snd_pcm_lib_malloc_pages()` is available only when the DMA buffers have been pre-allocated. See the section `Buffer Types`_ for more details. -Note that this and ``prepare`` callbacks may be called multiple times -per initialization. For example, the OSS emulation may call these +Note that this one and the ``prepare`` callback may be called multiple +times per initialization. For example, the OSS emulation may call these callbacks at each change via its ioctl. Thus, you need to be careful not to allocate the same buffers many times, which will lead to memory leaks! Calling the helper function above many times is OK. It will release the previous buffer automatically when it was already allocated. -Another note is that this callback is non-atomic (schedulable) as +Another note is that this callback is non-atomic (schedulable) by default, i.e. when no ``nonatomic`` flag set. This is important, because the ``trigger`` callback is atomic (non-schedulable). That is, -mutexes or any schedule-related functions are not available in +mutexes or any schedule-related functions are not available in the ``trigger`` callback. Please see the subsection Atomicity_ for details. @@ -1979,33 +1882,31 @@ This is called to release the resources allocated via This function is always called before the close callback is called. Also, the callback may be called multiple times, too. Keep track -whether the resource was already released. +whether each resource was already released. -When you have set up the managed buffer allocation mode for the PCM +When you have chosen managed buffer allocation mode for the PCM substream, the allocated PCM buffer will be automatically released after this callback gets called. Otherwise you'll have to release the buffer manually. Typically, when the buffer was allocated from the pre-allocated pool, you can use the standard API function -:c:func:`snd_pcm_lib_malloc_pages()` like: - -:: +:c:func:`snd_pcm_lib_malloc_pages()` like:: snd_pcm_lib_free_pages(substream); prepare callback ~~~~~~~~~~~~~~~~ :: static int snd_xxx_prepare(struct snd_pcm_substream *substream); -This callback is called when the pcm is “prepared”. You can set the +This callback is called when the PCM is “prepared”. You can set the format type, sample rate, etc. here. The difference from ``hw_params`` is that the ``prepare`` callback will be called each time :c:func:`snd_pcm_prepare()` is called, i.e. when recovering after underruns, etc. -Note that this callback is now non-atomic. You can use +Note that this callback is non-atomic. You can use schedule-related functions safely in this callback. In this and the following callbacks, you can refer to the values via @@ -2026,13 +1927,11 @@ trigger callback static int snd_xxx_trigger(struct snd_pcm_substream *substream, int cmd); -This is called when the pcm is started, stopped or paused. +This is called when the PCM is started, stopped or paused. -Which action is specified in the second argument, -``SNDRV_PCM_TRIGGER_XXX`` in ``<sound/pcm.h>``. At least, the ``START`` -and ``STOP`` commands must be defined in this callback. - -:: +The action is specified in the second argument, ``SNDRV_PCM_TRIGGER_XXX`` +defined in ``<sound/pcm.h>``. At least, the ``START`` +and ``STOP`` commands must be defined in this callback:: switch (cmd) { case SNDRV_PCM_TRIGGER_START: @@ -2045,49 +1944,49 @@ and ``STOP`` commands must be defined in this callback. return -EINVAL; } -When the pcm supports the pause operation (given in the info field of +When the PCM supports the pause operation (given in the info field of the hardware table), the ``PAUSE_PUSH`` and ``PAUSE_RELEASE`` commands -must be handled here, too. The former is the command to pause the pcm, -and the latter to restart the pcm again. +must be handled here, too. The former is the command to pause the PCM, +and the latter to restart the PCM again. -When the pcm supports the suspend/resume operation, regardless of full +When the PCM supports the suspend/resume operation, regardless of full or partial suspend/resume support, the ``SUSPEND`` and ``RESUME`` commands must be handled, too. These commands are issued when the power-management status is changed. Obviously, the ``SUSPEND`` and -``RESUME`` commands suspend and resume the pcm substream, and usually, +``RESUME`` commands suspend and resume the PCM substream, and usually, they are identical to the ``STOP`` and ``START`` commands, respectively. See the `Power Management`_ section for details. -As mentioned, this callback is atomic as default unless ``nonatomic`` +As mentioned, this callback is atomic by default unless the ``nonatomic`` flag set, and you cannot call functions which may sleep. The ``trigger`` callback should be as minimal as possible, just really -triggering the DMA. The other stuff should be initialized +triggering the DMA. The other stuff should be initialized in ``hw_params`` and ``prepare`` callbacks properly beforehand. sync_stop callback ~~~~~~~~~~~~~~~~~~ :: static int snd_xxx_sync_stop(struct snd_pcm_substream *substream); This callback is optional, and NULL can be passed. It's called after -the PCM core stops the stream and changes the stream state +the PCM core stops the stream, before it changes the stream state via ``prepare``, ``hw_params`` or ``hw_free``. Since the IRQ handler might be still pending, we need to wait until the pending task finishes before moving to the next step; otherwise it -might lead to a crash due to resource conflicts or access to the freed +might lead to a crash due to resource conflicts or access to freed resources. A typical behavior is to call a synchronization function like :c:func:`synchronize_irq()` here. -For majority of drivers that need only a call of +For the majority of drivers that need only a call of :c:func:`synchronize_irq()`, there is a simpler setup, too. -While keeping NULL to ``sync_stop`` PCM callback, the driver can set -``card->sync_irq`` field to store the valid interrupt number after -requesting an IRQ, instead. Then PCM core will look call +While keeping the ``sync_stop`` PCM callback NULL, the driver can set +the ``card->sync_irq`` field to the returned interrupt number after +requesting an IRQ, instead. Then PCM core will call :c:func:`synchronize_irq()` with the given IRQ appropriately. -If the IRQ handler is released at the card destructor, you don't need +If the IRQ handler is released by the card destructor, you don't need to clear ``card->sync_irq``, as the card itself is being released. So, usually you'll need to add just a single line for assigning ``card->sync_irq`` in the driver code unless the driver re-acquires @@ -2103,76 +2002,76 @@ pointer callback static snd_pcm_uframes_t snd_xxx_pointer(struct snd_pcm_substream *substream) This callback is called when the PCM middle layer inquires the current -hardware position on the buffer. The position must be returned in +hardware position in the buffer. The position must be returned in frames, ranging from 0 to ``buffer_size - 1``. -This is called usually from the buffer-update routine in the pcm +This is usually called from the buffer-update routine in the PCM middle layer, which is invoked when :c:func:`snd_pcm_period_elapsed()` -is called in the interrupt routine. Then the pcm middle layer updates +is called by the interrupt routine. Then the PCM middle layer updates the position and calculates the available space, and wakes up the sleeping poll threads, etc. -This callback is also atomic as default. +This callback is also atomic by default. copy_user, copy_kernel and fill_silence ops ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ These callbacks are not mandatory, and can be omitted in most cases. These callbacks are used when the hardware buffer cannot be in the -normal memory space. Some chips have their own buffer on the hardware +normal memory space. Some chips have their own buffer in the hardware which is not mappable. In such a case, you have to transfer the data manually from the memory buffer to the hardware buffer. Or, if the buffer is non-contiguous on both physical and virtual memory spaces, these callbacks must be defined, too. If these two callbacks are defined, copy and set-silence operations -are done by them. The detailed will be described in the later section +are done by them. The details will be described in the later section `Buffer and Memory Management`_. ack callback ~~~~~~~~~~~~ This callback is also not mandatory. This callback is called when the ``appl_ptr`` is updated in read or write operations. Some drivers like emu10k1-fx and cs46xx need to track the current ``appl_ptr`` for the internal buffer, and this callback is useful only for such a purpose. The callback function may return 0 or a negative error. When the -return value is ``-EPIPE``, PCM core treats as a buffer XRUN happens, +return value is ``-EPIPE``, PCM core treats that as a buffer XRUN, and changes the state to ``SNDRV_PCM_STATE_XRUN`` automatically. -This callback is atomic as default. +This callback is atomic by default. page callback ~~~~~~~~~~~~~ This callback is optional too. The mmap calls this callback to get the page fault address. -Since the recent changes, you need no special callback any longer for -the standard SG-buffer or vmalloc-buffer. Hence this callback should -be rarely used. +You need no special callback for the standard SG-buffer or vmalloc- +buffer. Hence this callback should be rarely used. -mmap calllback -~~~~~~~~~~~~~~ +mmap callback +~~~~~~~~~~~~~ This is another optional callback for controlling mmap behavior. -Once when defined, PCM core calls this callback when a page is -memory-mapped instead of dealing via the standard helper. +When defined, the PCM core calls this callback when a page is +memory-mapped, instead of using the standard helper. If you need special handling (due to some architecture or device-specific issues), implement everything here as you like. PCM Interrupt Handler --------------------- -The rest of pcm stuff is the PCM interrupt handler. The role of PCM +The remainder of the PCM stuff is the PCM interrupt handler. The role +of the PCM interrupt handler in the sound driver is to update the buffer position and to tell the PCM middle layer when the buffer position goes across -the prescribed period size. To inform this, call the +the specified period boundary. To inform about this, call the :c:func:`snd_pcm_period_elapsed()` function. -There are several types of sound chips to generate the interrupts. +There are several ways sound chips can generate interrupts. Interrupts at the period (fragment) boundary ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ @@ -2188,14 +2087,12 @@ chip record to hold the current running substream pointer, and set the pointer value at ``open`` callback (and reset at ``close`` callback). If you acquire a spinlock in the interrupt handler, and the lock is used -in other pcm callbacks, too, then you have to release the lock before +in other PCM callbacks, too, then you have to release the lock before calling :c:func:`snd_pcm_period_elapsed()`, because -:c:func:`snd_pcm_period_elapsed()` calls other pcm callbacks +:c:func:`snd_pcm_period_elapsed()` calls other PCM callbacks inside. -Typical code would be like: - -:: +Typical code would look like:: static irqreturn_t snd_mychip_interrupt(int irq, void *dev_id) @@ -2233,9 +2130,7 @@ position and accumulate the processed sample length at each interrupt. When the accumulated size exceeds the period size, call :c:func:`snd_pcm_period_elapsed()` and reset the accumulator. -Typical code would be like the following. - -:: +Typical code would look as follows:: static irqreturn_t snd_mychip_interrupt(int irq, void *dev_id) @@ -2280,25 +2175,25 @@ Typical code would be like the following. On calling :c:func:`snd_pcm_period_elapsed()` ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ -In both cases, even if more than one period are elapsed, you don't have +In both cases, even if more than one period has elapsed, you don't have to call :c:func:`snd_pcm_period_elapsed()` many times. Call only -once. And the pcm layer will check the current hardware pointer and +once. And the PCM layer will check the current hardware pointer and update to the latest status. Atomicity --------- One of the most important (and thus difficult to debug) problems in kernel programming are race conditions. In the Linux kernel, they are usually avoided via spin-locks, mutexes or semaphores. In general, if a race condition can happen in an interrupt handler, it has to be managed atomically, and you have to use a spinlock to protect the critical -session. If the critical section is not in interrupt handler code and if +section. If the critical section is not in interrupt handler code and if taking a relatively long time to execute is acceptable, you should use mutexes or semaphores instead. -As already seen, some pcm callbacks are atomic and some are not. For -example, the ``hw_params`` callback is non-atomic, while ``trigger`` +As already seen, some PCM callbacks are atomic and some are not. For +example, the ``hw_params`` callback is non-atomic, while the ``trigger`` callback is atomic. This means, the latter is called already in a spinlock held by the PCM middle layer, the PCM stream lock. Please take this atomicity into account when you choose a locking scheme in @@ -2313,13 +2208,13 @@ callback, please use :c:func:`udelay()` or :c:func:`mdelay()`. All three atomic callbacks (trigger, pointer, and ack) are called with local interrupts disabled. -The recent changes in PCM core code, however, allow all PCM operations -to be non-atomic. This assumes that the all caller sides are in +However, it is possible to request all PCM operations to be non-atomic. +This assumes that all call sites are in non-atomic contexts. For example, the function :c:func:`snd_pcm_period_elapsed()` is called typically from the interrupt handler. But, if you set up the driver to use a threaded interrupt handler, this call can be in non-atomic context, too. In such -a case, you can set ``nonatomic`` filed of struct snd_pcm object +a case, you can set the ``nonatomic`` field of the struct snd_pcm object after creating it. When this flag is set, mutex and rwsem are used internally in the PCM core instead of spin and rwlocks, so that you can call all PCM functions safely in a non-atomic @@ -2335,14 +2230,12 @@ too. Constraints ----------- -If your chip supports unconventional sample rates, or only the limited -samples, you need to set a constraint for the condition. +Due to physical limitations, hardware is not infinitely configurable. +These limitations are expressed by setting constraints. -For example, in order to restrict the sample rates in the some supported +For example, in order to restrict the sample rates to some supported values, use :c:func:`snd_pcm_hw_constraint_list()`. You need to -call this function in the open callback. - -:: +call this function in the open callback:: static unsigned int rates[] = {4000, 10000, 22050, 44100}; @@ -2364,16 +2257,12 @@ call this function in the open callback. .... } - - There are many different constraints. Look at ``sound/pcm.h`` for a complete list. You can even define your own constraint rules. For example, let's suppose my_chip can manage a substream of 1 channel if and only if the format is ``S16_LE``, otherwise it supports any format -specified in struct snd_pcm_hardware> (or in any other -constraint_list). You can build a rule like this: - -:: +specified in struct snd_pcm_hardware (or in any other +constraint_list). You can build a rule like this:: static int hw_rule_channels_by_format(struct snd_pcm_hw_params *params, struct snd_pcm_hw_rule *rule) @@ -2393,20 +2282,16 @@ constraint_list). You can build a rule like this: } -Then you need to call this function to add your rule: - -:: +Then you need to call this function to add your rule:: snd_pcm_hw_rule_add(substream->runtime, 0, SNDRV_PCM_HW_PARAM_CHANNELS, hw_rule_channels_by_format, NULL, SNDRV_PCM_HW_PARAM_FORMAT, -1); The rule function is called when an application sets the PCM format, and it refines the number of channels accordingly. But an application may set the number of channels before setting the format. Thus you also need -to define the inverse rule: - -:: +to define the inverse rule:: static int hw_rule_format_by_channels(struct snd_pcm_hw_params *params, struct snd_pcm_hw_rule *rule) @@ -2425,34 +2310,30 @@ to define the inverse rule: } -... and in the open callback: - -:: +... and in the open callback:: snd_pcm_hw_rule_add(substream->runtime, 0, SNDRV_PCM_HW_PARAM_FORMAT, hw_rule_format_by_channels, NULL, SNDRV_PCM_HW_PARAM_CHANNELS, -1); One typical usage of the hw constraints is to align the buffer size -with the period size. As default, ALSA PCM core doesn't enforce the +with the period size. By default, ALSA PCM core doesn't enforce the buffer size to be aligned with the period size. For example, it'd be possible to have a combination like 256 period bytes with 999 buffer bytes. Many device chips, however, require the buffer to be a multiple of periods. In such a case, call :c:func:`snd_pcm_hw_constraint_integer()` for -``SNDRV_PCM_HW_PARAM_PERIODS``. - -:: +``SNDRV_PCM_HW_PARAM_PERIODS``:: snd_pcm_hw_constraint_integer(substream->runtime, SNDRV_PCM_HW_PARAM_PERIODS); This assures that the number of periods is integer, hence the buffer size is aligned with the period size. -The hw constraint is a very much powerful mechanism to define the +The hw constraint is a very powerful mechanism to define the preferred PCM configuration, and there are relevant helpers. I won't give more details here, rather I would like to say, “Luke, use the source.” @@ -2479,9 +2360,7 @@ Definition of Controls To create a new control, you need to define the following three callbacks: ``info``, ``get`` and ``put``. Then, define a -struct snd_kcontrol_new record, such as: - -:: +struct snd_kcontrol_new record, such as:: static struct snd_kcontrol_new my_control = { @@ -2524,7 +2403,7 @@ The ``private_value`` field contains an arbitrary long integer value for this record. When using the generic ``info``, ``get`` and ``put`` callbacks, you can pass a value through this field. If several small numbers are necessary, you can combine them in bitwise. Or, it's -possible to give a pointer (casted to unsigned long) of some record to +possible to store a pointer (casted to unsigned long) of some record in this field, too. The ``tlv`` field can be used to provide metadata about the control; @@ -2591,7 +2470,7 @@ The access flag is the bitmask which specifies the access type of the given control. The default access type is ``SNDRV_CTL_ELEM_ACCESS_READWRITE``, which means both read and write are allowed to this control. When the access flag is omitted (i.e. = 0), it -is considered as ``READWRITE`` access as default. +is considered as ``READWRITE`` access by default. When the control is read-only, pass ``SNDRV_CTL_ELEM_ACCESS_READ`` instead. In this case, you don't have to define the ``put`` callback. @@ -2604,21 +2483,22 @@ If the control value changes frequently (e.g. the VU meter), changed without `Change notification`_. Applications should poll such a control constantly. -When the control is inactive, set the ``INACTIVE`` flag, too. There are -``LOCK`` and ``OWNER`` flags to change the write permissions. +When the control may be updated, but currently has no effect on anything, +setting the ``INACTIVE`` flag may be appropriate. For example, PCM +controls should be inactive while no PCM device is open. + +There are ``LOCK`` and ``OWNER`` flags to change the write permissions. Control Callbacks ----------------- info callback ~~~~~~~~~~~~~ The ``info`` callback is used to get detailed information on this control. This must store the values of the given struct snd_ctl_elem_info object. For example, -for a boolean control with a single element: - -:: +for a boolean control with a single element:: static int snd_myctl_mono_info(struct snd_kcontrol *kcontrol, @@ -2637,13 +2517,11 @@ The ``type`` field specifies the type of the control. There are ``BOOLEAN``, ``INTEGER``, ``ENUMERATED``, ``BYTES``, ``IEC958`` and ``INTEGER64``. The ``count`` field specifies the number of elements in this control. For example, a stereo volume would have count = 2. The -``value`` field is a union, and the values stored are depending on the +``value`` field is a union, and the values stored depend on the type. The boolean and integer types are identical. -The enumerated type is a bit different from others. You'll need to set -the string for the currently given item index. - -:: +The enumerated type is a bit different from the others. You'll need to +set the string for the selectec item index:: static int snd_myctl_enum_info(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_info *uinfo) @@ -2688,13 +2566,10 @@ stereo channel boolean item. get callback ~~~~~~~~~~~~ -This callback is used to read the current value of the control and to -return to user-space. - -For example, - -:: +This callback is used to read the current value of the control, so it +can be returned to user-space. +For example:: static int snd_myctl_get(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol) @@ -2709,39 +2584,32 @@ For example, The ``value`` field depends on the type of control as well as on the info callback. For example, the sb driver uses this field to store the register offset, the bit-shift and the bit-mask. The ``private_value`` -field is set as follows: - -:: +field is set as follows:: .private_value = reg | (shift << 16) | (mask << 24) -and is retrieved in callbacks like - -:: +and is retrieved in callbacks like:: static int snd_sbmixer_get_single(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol) { int reg = kcontrol->private_value & 0xff; int shift = (kcontrol->private_value >> 16) & 0xff; int mask = (kcontrol->private_value >> 24) & 0xff; .... } In the ``get`` callback, you have to fill all the elements if the -control has more than one elements, i.e. ``count > 1``. In the example +control has more than one element, i.e. ``count > 1``. In the example above, we filled only one element (``value.integer.value[0]``) since -it's assumed as ``count = 1``. +``count = 1`` is assumed. put callback ~~~~~~~~~~~~ -This callback is used to write a value from user-space. - -For example, - -:: +This callback is used to write a value coming from user-space. +For example:: static int snd_myctl_put(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol) @@ -2764,23 +2632,21 @@ value is not changed, return 0 instead. If any fatal error happens, return a negative error code as usual. As in the ``get`` callback, when the control has more than one -elements, all elements must be evaluated in this callback, too. +element, all elements must be evaluated in this callback, too. Callbacks are not atomic ~~~~~~~~~~~~~~~~~~~~~~~~ -All these three callbacks are basically not atomic. +All these three callbacks are basically (FIXME: but ...?) not atomic. Control Constructor ------------------- When everything is ready, finally we can create a new control. To create a control, there are two functions to be called, :c:func:`snd_ctl_new1()` and :c:func:`snd_ctl_add()`. -In the simplest way, you can do like this: - -:: +In the simplest way, you can do it like this:: err = snd_ctl_add(card, snd_ctl_new1(&my_control, chip)); if (err < 0) @@ -2798,9 +2664,7 @@ Change Notification ------------------- If you need to change and update a control in the interrupt routine, you -can call :c:func:`snd_ctl_notify()`. For example, - -:: +can call :c:func:`snd_ctl_notify()`. For example:: snd_ctl_notify(card, SNDRV_CTL_EVENT_MASK_VALUE, id_pointer); @@ -2814,13 +2678,11 @@ for hardware volume interrupts. Metadata -------- -To provide information about the dB values of a mixer control, use on of +To provide information about the dB values of a mixer control, use one of the ``DECLARE_TLV_xxx`` macros from ``<sound/tlv.h>`` to define a variable containing this information, set the ``tlv.p`` field to point to this variable, and include the ``SNDRV_CTL_ELEM_ACCESS_TLV_READ`` flag -in the ``access`` field; like this: - -:: +in the ``access`` field; like this:: static DECLARE_TLV_DB_SCALE(db_scale_my_control, -4050, 150, 0); @@ -2910,24 +2772,20 @@ AC97 Constructor ---------------- To create an ac97 instance, first call :c:func:`snd_ac97_bus()` -with an ``ac97_bus_ops_t`` record with callback functions. - -:: +with an ``ac97_bus_ops_t`` record with callback functions:: struct snd_ac97_bus *bus; static struct snd_ac97_bus_ops ops = { .write = snd_mychip_ac97_write, .read = snd_mychip_ac97_read, }; snd_ac97_bus(card, 0, &ops, NULL, &pbus); The bus record is shared among all belonging ac97 instances. -And then call :c:func:`snd_ac97_mixer()` with an struct snd_ac97_template -record together with the bus pointer created above. - -:: +And then call :c:func:`snd_ac97_mixer()` with a struct snd_ac97_template +record together with the bus pointer created above:: struct snd_ac97_template ac97; int err; @@ -2952,9 +2810,7 @@ correspond to the functions for read and write accesses to the hardware low-level codes. The ``read`` callback returns the register value specified in the -argument. - -:: +argument:: static unsigned short snd_mychip_ac97_read(struct snd_ac97 *ac97, unsigned short reg) @@ -2967,9 +2823,7 @@ argument. Here, the chip can be cast from ``ac97->private_data``. Meanwhile, the ``write`` callback is used to set the register -value - -:: +value:: static void snd_mychip_ac97_write(struct snd_ac97 *ac97, unsigned short reg, unsigned short val) @@ -3002,32 +2856,24 @@ Both :c:func:`snd_ac97_write()` and the given register (``AC97_XXX``). The difference between them is that :c:func:`snd_ac97_update()` doesn't write a value if the given value has been already set, while :c:func:`snd_ac97_write()` -always rewrites the value. - -:: +always rewrites the value:: snd_ac97_write(ac97, AC97_MASTER, 0x8080); snd_ac97_update(ac97, AC97_MASTER, 0x8080); :c:func:`snd_ac97_read()` is used to read the value of the given -register. For example, - -:: +register. For example:: value = snd_ac97_read(ac97, AC97_MASTER); :c:func:`snd_ac97_update_bits()` is used to update some bits in -the given register. - -:: +the given register:: snd_ac97_update_bits(ac97, reg, mask, value); Also, there is a function to change the sample rate (of a given register such as ``AC97_PCM_FRONT_DAC_RATE``) when VRA or DRA is supported by the -codec: :c:func:`snd_ac97_set_rate()`. - -:: +codec: :c:func:`snd_ac97_set_rate()`:: snd_ac97_set_rate(ac97, AC97_PCM_FRONT_DAC_RATE, 44100); @@ -3082,9 +2928,7 @@ mpu401 stuff. For example, emu10k1 has its own mpu401 routines. MIDI Constructor ---------------- -To create a rawmidi object, call :c:func:`snd_mpu401_uart_new()`. - -:: +To create a rawmidi object, call :c:func:`snd_mpu401_uart_new()`:: struct snd_rawmidi *rmidi; snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401, port, info_flags, @@ -3129,16 +2973,12 @@ corresponds to the data port. If not, you may change the ``cport`` field of struct snd_mpu401 manually afterward. However, struct snd_mpu401 pointer is not returned explicitly by :c:func:`snd_mpu401_uart_new()`. You -need to cast ``rmidi->private_data`` to struct snd_mpu401 explicitly, - -:: +need to cast ``rmidi->private_data`` to struct snd_mpu401 explicitly:: struct snd_mpu401 *mpu; mpu = rmidi->private_data; -and reset the ``cport`` as you like: - -:: +and reset the ``cport`` as you like:: mpu->cport = my_own_control_port; @@ -3162,9 +3002,7 @@ occurred. In this case, you need to pass the private_data of the returned rawmidi object from :c:func:`snd_mpu401_uart_new()` as the second -argument of :c:func:`snd_mpu401_uart_interrupt()`. - -:: +argument of :c:func:`snd_mpu401_uart_interrupt()`:: snd_mpu401_uart_interrupt(irq, rmidi->private_data, regs); @@ -3188,9 +3026,7 @@ RawMIDI Constructor ------------------- To create a rawmidi device, call the :c:func:`snd_rawmidi_new()` -function: - -:: +function:: struct snd_rawmidi *rmidi; err = snd_rawmidi_new(chip->card, "MyMIDI", 0, outs, ins, &rmidi); @@ -3220,29 +3056,23 @@ output and input at the same time. After the rawmidi device is created, you need to set the operators (callbacks) for each substream. There are helper functions to set the -operators for all the substreams of a device: - -:: +operators for all the substreams of a device:: snd_rawmidi_set_ops(rmidi, SNDRV_RAWMIDI_STREAM_OUTPUT, &snd_mymidi_output_ops); snd_rawmidi_set_ops(rmidi, SNDRV_RAWMIDI_STREAM_INPUT, &snd_mymidi_input_ops); -The operators are usually defined like this: - -:: +The operators are usually defined like this:: static struct snd_rawmidi_ops snd_mymidi_output_ops = { .open = snd_mymidi_output_open, .close = snd_mymidi_output_close, .trigger = snd_mymidi_output_trigger, }; These callbacks are explained in the `RawMIDI Callbacks`_ section. If there are more than one substream, you should give a unique name to -each of them: - -:: +each of them:: struct snd_rawmidi_substream *substream; list_for_each_entry(substream, @@ -3260,9 +3090,7 @@ device can be accessed as ``substream->rmidi->private_data``. If there is more than one port, your callbacks can determine the port index from the struct snd_rawmidi_substream data passed to each -callback: - -:: +callback:: struct snd_rawmidi_substream *substream; int index = substream->number; @@ -3307,23 +3135,19 @@ of bytes that have been read; this will be less than the number of bytes requested when there are no more data in the buffer. After the data have been transmitted successfully, call :c:func:`snd_rawmidi_transmit_ack()` to remove the data from the -substream buffer: - -:: +substream buffer:: unsigned char data; while (snd_rawmidi_transmit_peek(substream, &data, 1) == 1) { if (snd_mychip_try_to_transmit(data)) snd_rawmidi_transmit_ack(substream, 1); else break; /* hardware FIFO full */ } If you know beforehand that the hardware will accept data, you can use the :c:func:`snd_rawmidi_transmit()` function which reads some -data and removes them from the buffer at once: - -:: +data and removes them from the buffer at once:: while (snd_mychip_transmit_possible()) { unsigned char data; @@ -3358,9 +3182,7 @@ The ``trigger`` callback must not sleep; the actual reading of data from the device is usually done in an interrupt handler. When data reception is enabled, your interrupt handler should call -:c:func:`snd_rawmidi_receive()` for all received data: - -:: +:c:func:`snd_rawmidi_receive()` for all received data:: void snd_mychip_midi_interrupt(...) { @@ -3406,9 +3228,7 @@ whereas in OSS compatible mode, FM registers can be accessed with the OSS direct-FM compatible API in ``/dev/dmfmX`` device. To create the OPL3 component, you have two functions to call. The first -one is a constructor for the ``opl3_t`` instance. - -:: +one is a constructor for the ``opl3_t`` instance:: struct snd_opl3 *opl3; snd_opl3_create(card, lport, rport, OPL3_HW_OPL3_XXX, @@ -3426,9 +3246,7 @@ the opl3 module will allocate the specified ports by itself. When the accessing the hardware requires special method instead of the standard I/O access, you can create opl3 instance separately with -:c:func:`snd_opl3_new()`. - -:: +:c:func:`snd_opl3_new()`:: struct snd_opl3 *opl3; snd_opl3_new(card, OPL3_HW_OPL3_XXX, &opl3); @@ -3445,9 +3263,7 @@ proper state. Note that :c:func:`snd_opl3_create()` always calls it internally. If the opl3 instance is created successfully, then create a hwdep device -for this opl3. - -:: +for this opl3:: struct snd_hwdep *opl3hwdep; snd_opl3_hwdep_new(opl3, 0, 1, &opl3hwdep); @@ -3469,40 +3285,32 @@ the micro code. In such a case, you can create a hwdep ``isa/sb/sb16_csp.c``. The creation of the ``hwdep`` instance is done via -:c:func:`snd_hwdep_new()`. - -:: +:c:func:`snd_hwdep_new()`:: struct snd_hwdep *hw; snd_hwdep_new(card, "My HWDEP", 0, &hw); where the third argument is the index number. You can then pass any pointer value to the ``private_data``. If you -assign a private data, you should define the destructor, too. The -destructor function is set in the ``private_free`` field. - -:: +assign private data, you should define a destructor, too. The +destructor function is set in the ``private_free`` field:: struct mydata *p = kmalloc(sizeof(*p), GFP_KERNEL); hw->private_data = p; hw->private_free = mydata_free; -and the implementation of the destructor would be: - -:: +and the implementation of the destructor would be:: static void mydata_free(struct snd_hwdep *hw) { struct mydata *p = hw->private_data; kfree(p); } The arbitrary file operations can be defined for this instance. The file operators are defined in the ``ops`` table. For example, assume that -this chip needs an ioctl. - -:: +this chip needs an ioctl:: hw->ops.open = mydata_open; hw->ops.ioctl = mydata_ioctl; @@ -3552,92 +3360,87 @@ Buffer Types ALSA provides several different buffer allocation functions depending on the bus and the architecture. All these have a consistent API. The -allocation of physically-contiguous pages is done via +allocation of physically-contiguous pages is done via the :c:func:`snd_malloc_xxx_pages()` function, where xxx is the bus type. -The allocation of pages with fallback is -:c:func:`snd_malloc_xxx_pages_fallback()`. This function tries -to allocate the specified pages but if the pages are not available, it -tries to reduce the page sizes until enough space is found. +The allocation of pages with fallback is done via +:c:func:`snd_dma_alloc_pages_fallback()`. This function tries +to allocate the specified number of pages, but if not enough pages are +available, it tries to reduce the request size until enough space +is found, down to one page. -The release the pages, call :c:func:`snd_free_xxx_pages()` +To release the pages, call the :c:func:`snd_dma_free_pages()` function. Usually, ALSA drivers try to allocate and reserve a large contiguous -physical space at the time the module is loaded for the later use. This +physical space at the time the module is loaded for later use. This is called “pre-allocation”. As already written, you can call the -following function at pcm instance construction time (in the case of PCI -bus). - -:: +following function at PCM instance construction time (in the case of PCI +bus):: snd_pcm_lib_preallocate_pages_for_all(pcm, SNDRV_DMA_TYPE_DEV, &pci->dev, size, max); -where ``size`` is the byte size to be pre-allocated and the ``max`` is -the maximum size to be changed via the ``prealloc`` proc file. The +where ``size`` is the byte size to be pre-allocated and ``max`` is +the maximum size settable via the ``prealloc`` proc file. The allocator will try to get an area as large as possible within the given size. The second argument (type) and the third argument (device pointer) are dependent on the bus. For normal devices, pass the device pointer (typically identical as ``card->dev``) to the third argument with ``SNDRV_DMA_TYPE_DEV`` type. -For the continuous buffer unrelated to the +A continuous buffer unrelated to the bus can be pre-allocated with ``SNDRV_DMA_TYPE_CONTINUOUS`` type. You can pass NULL to the device pointer in that case, which is the -default mode implying to allocate with ``GFP_KERNEL`` flag. +default mode implying to allocate with the ``GFP_KERNEL`` flag. If you need a restricted (lower) address, set up the coherent DMA mask bits for the device, and pass the device pointer, like the normal device memory allocations. For this type, it's still allowed to pass NULL to the device pointer, too, if no address restriction is needed. For the scatter-gather buffers, use ``SNDRV_DMA_TYPE_DEV_SG`` with the device pointer (see the `Non-Contiguous Buffers`_ section). Once the buffer is pre-allocated, you can use the allocator in the -``hw_params`` callback: - -:: +``hw_params`` callback:: snd_pcm_lib_malloc_pages(substream, size); Note that you have to pre-allocate to use this function. -Most of drivers use, though, rather the newly introduced "managed -buffer allocation mode" instead of the manual allocation or release. +But most drivers use the "managed buffer allocation mode" instead +of manual allocation and release. This is done by calling :c:func:`snd_pcm_set_managed_buffer_all()` -instead of :c:func:`snd_pcm_lib_preallocate_pages_for_all()`. - -:: +instead of :c:func:`snd_pcm_lib_preallocate_pages_for_all()`:: snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_DEV, &pci->dev, size, max); -where passed arguments are identical in both functions. +where the passed arguments are identical for both functions. The difference in the managed mode is that PCM core will call :c:func:`snd_pcm_lib_malloc_pages()` internally already before calling the PCM ``hw_params`` callback, and call :c:func:`snd_pcm_lib_free_pages()` after the PCM ``hw_free`` callback automatically. So the driver doesn't have to call these functions explicitly in its callback any -longer. This made many driver code having NULL ``hw_params`` and +longer. This allows many drivers to have NULL ``hw_params`` and ``hw_free`` entries. External Hardware Buffers ------------------------- -Some chips have their own hardware buffers and the DMA transfer from the +Some chips have their own hardware buffers and DMA transfer from the host memory is not available. In such a case, you need to either 1) copy/set the audio data directly to the external hardware buffer, or 2) make an intermediate buffer and copy/set the data from it to the external hardware buffer in interrupts (or in tasklets, preferably). The first case works fine if the external hardware buffer is large enough. This method doesn't need any extra buffers and thus is more -effective. You need to define the ``copy_user`` and ``copy_kernel`` -callbacks for the data transfer, in addition to ``fill_silence`` +efficient. You need to define the ``copy_user`` and ``copy_kernel`` +callbacks for the data transfer, in addition to the ``fill_silence`` callback for playback. However, there is a drawback: it cannot be mmapped. The examples are GUS's GF1 PCM or emu8000's wavetable PCM. @@ -3651,157 +3454,137 @@ buffer instead of the host memory. In this case, mmap is available only on certain architectures like the Intel one. In non-mmap mode, the data cannot be transferred as in the normal way. Thus you need to define the ``copy_user``, ``copy_kernel`` and ``fill_silence`` callbacks as well, -as in the cases above. The examples are found in ``rme32.c`` and +as in the cases above. Examples are found in ``rme32.c`` and ``rme96.c``. The implementation of the ``copy_user``, ``copy_kernel`` and ``silence`` callbacks depends upon whether the hardware supports interleaved or non-interleaved samples. The ``copy_user`` callback is -defined like below, a bit differently depending whether the direction -is playback or capture: - -:: +defined like below, a bit differently depending on whether the direction +is playback or capture:: static int playback_copy_user(struct snd_pcm_substream *substream, int channel, unsigned long pos, void __user *src, unsigned long count); static int capture_copy_user(struct snd_pcm_substream *substream, int channel, unsigned long pos, void __user *dst, unsigned long count); In the case of interleaved samples, the second argument (``channel``) is -not used. The third argument (``pos``) points the current position -offset in bytes. +not used. The third argument (``pos``) specifies the position in bytes. The meaning of the fourth argument is different between playback and capture. For playback, it holds the source data pointer, and for capture, it's the destination data pointer. The last argument is the number of bytes to be copied. What you have to do in this callback is again different between playback and capture directions. In the playback case, you copy the given amount of data (``count``) at the specified pointer (``src``) to the specified -offset (``pos``) on the hardware buffer. When coded like memcpy-like -way, the copy would be like: - -:: +offset (``pos``) in the hardware buffer. When coded like memcpy-like +way, the copy would look like:: my_memcpy_from_user(my_buffer + pos, src, count); For the capture direction, you copy the given amount of data (``count``) -at the specified offset (``pos``) on the hardware buffer to the -specified pointer (``dst``). - -:: +at the specified offset (``pos``) in the hardware buffer to the +specified pointer (``dst``):: my_memcpy_to_user(dst, my_buffer + pos, count); -Here the functions are named as ``from_user`` and ``to_user`` because +Here the functions are named ``from_user`` and ``to_user`` because it's the user-space buffer that is passed to these callbacks. That -is, the callback is supposed to copy from/to the user-space data +is, the callback is supposed to copy data from/to the user-space directly to/from the hardware buffer. Careful readers might notice that these callbacks receive the arguments in bytes, not in frames like other callbacks. It's because -it would make coding easier like the examples above, and also it makes -easier to unify both the interleaved and non-interleaved cases, as -explained in the following. +this makes coding easier like in the examples above, and also it makes +it easier to unify both the interleaved and non-interleaved cases, as +explained below. In the case of non-interleaved samples, the implementation will be a bit -more complicated. The callback is called for each channel, passed by -the second argument, so totally it's called for N-channels times per -transfer. +more complicated. The callback is called for each channel, passed in +the second argument, so in total it's called N times per transfer. -The meaning of other arguments are almost same as the interleaved -case. The callback is supposed to copy the data from/to the given -user-space buffer, but only for the given channel. For the detailed -implementations, please check ``isa/gus/gus_pcm.c`` or -"pci/rme9652/rme9652.c" as examples. +The meaning of the other arguments are almost the same as in the +interleaved case. The callback is supposed to copy the data from/to +the given user-space buffer, but only for the given channel. For +details, please check ``isa/gus/gus_pcm.c`` or ``pci/rme9652/rme9652.c`` +as examples. -The above callbacks are the copy from/to the user-space buffer. There -are some cases where we want copy from/to the kernel-space buffer -instead. In such a case, ``copy_kernel`` callback is called. It'd -look like: - -:: +The above callbacks are the copies from/to the user-space buffer. There +are some cases where we want to copy from/to the kernel-space buffer +instead. In such a case, the ``copy_kernel`` callback is called. It'd +look like:: static int playback_copy_kernel(struct snd_pcm_substream *substream, int channel, unsigned long pos, void *src, unsigned long count); static int capture_copy_kernel(struct snd_pcm_substream *substream, int channel, unsigned long pos, void *dst, unsigned long count); As found easily, the only difference is that the buffer pointer is -without ``__user`` prefix; that is, a kernel-buffer pointer is passed +without a ``__user`` prefix; that is, a kernel-buffer pointer is passed in the fourth argument. Correspondingly, the implementation would be -a version without the user-copy, such as: - -:: +a version without the user-copy, such as:: my_memcpy(my_buffer + pos, src, count); Usually for the playback, another callback ``fill_silence`` is defined. It's implemented in a similar way as the copy callbacks -above: - -:: +above:: static int silence(struct snd_pcm_substream *substream, int channel, unsigned long pos, unsigned long count); The meanings of arguments are the same as in the ``copy_user`` and ``copy_kernel`` callbacks, although there is no buffer pointer argument. In the case of interleaved samples, the channel argument has -no meaning, as well as on ``copy_*`` callbacks. +no meaning, as for the ``copy_*`` callbacks. -The role of ``fill_silence`` callback is to set the given amount -(``count``) of silence data at the specified offset (``pos``) on the +The role of the ``fill_silence`` callback is to set the given amount +(``count``) of silence data at the specified offset (``pos``) in the hardware buffer. Suppose that the data format is signed (that is, the silent-data is 0), and the implementation using a memset-like function -would be like: - -:: +would look like:: my_memset(my_buffer + pos, 0, count); In the case of non-interleaved samples, again, the implementation -becomes a bit more complicated, as it's called N-times per transfer +becomes a bit more complicated, as it's called N times per transfer for each channel. See, for example, ``isa/gus/gus_pcm.c``. Non-Contiguous Buffers ---------------------- -If your hardware supports the page table as in emu10k1 or the buffer -descriptors as in via82xx, you can use the scatter-gather (SG) DMA. ALSA +If your hardware supports a page table as in emu10k1 or buffer +descriptors as in via82xx, you can use scatter-gather (SG) DMA. ALSA provides an interface for handling SG-buffers. The API is provided in ``<sound/pcm.h>``. For creating the SG-buffer handler, call :c:func:`snd_pcm_set_managed_buffer()` or :c:func:`snd_pcm_set_managed_buffer_all()` with -``SNDRV_DMA_TYPE_DEV_SG`` in the PCM constructor like other PCI -pre-allocator. You need to pass ``&pci->dev``, where pci is -the struct pci_dev pointer of the chip as -well. - -:: +``SNDRV_DMA_TYPE_DEV_SG`` in the PCM constructor like for other PCI +pre-allocations. You need to pass ``&pci->dev``, where pci is +the struct pci_dev pointer of the chip as well:: snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_DEV_SG, &pci->dev, size, max); +// FIXME: dma_private again The ``struct snd_sg_buf`` instance is created as -``substream->dma_private`` in turn. You can cast the pointer like: - -:: +``substream->dma_private`` in turn. You can cast the pointer like:: struct snd_sg_buf *sgbuf = (struct snd_sg_buf *)substream->dma_private; -Then in :c:func:`snd_pcm_lib_malloc_pages()` call, the common SG-buffer +Then in the :c:func:`snd_pcm_lib_malloc_pages()` call, the common SG-buffer handler will allocate the non-contiguous kernel pages of the given size -and map them onto the virtually contiguous memory. The virtual pointer -is addressed in runtime->dma_area. The physical address +and map them as virtually contiguous memory. The virtual pointer +is addressed via runtime->dma_area. The physical address (``runtime->dma_addr``) is set to zero, because the buffer is physically non-contiguous. The physical address table is set up in ``sgbuf->table``. You can get the physical address at a certain offset @@ -3814,36 +3597,32 @@ Vmalloc'ed Buffers ------------------ It's possible to use a buffer allocated via :c:func:`vmalloc()`, for -example, for an intermediate buffer. In the recent version of kernel, -you can simply allocate it via standard -:c:func:`snd_pcm_lib_malloc_pages()` and co after setting up the -buffer preallocation with ``SNDRV_DMA_TYPE_VMALLOC`` type. - -:: +example, for an intermediate buffer. +You can simply allocate it via the standard +:c:func:`snd_pcm_lib_malloc_pages()` and co. after setting up the +buffer preallocation with ``SNDRV_DMA_TYPE_VMALLOC`` type:: snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_VMALLOC, NULL, 0, 0); -The NULL is passed to the device pointer argument, which indicates -that the default pages (GFP_KERNEL and GFP_HIGHMEM) will be +NULL is passed as the device pointer argument, which indicates +that default pages (GFP_KERNEL and GFP_HIGHMEM) will be allocated. -Also, note that zero is passed to both the size and the max size -arguments here. Since each vmalloc call should succeed at any time, +Also, note that zero is passed as both the size and the max size +argument here. Since each vmalloc call should succeed at any time, we don't need to pre-allocate the buffers like other continuous pages. Proc Interface ============== ALSA provides an easy interface for procfs. The proc files are very useful for debugging. I recommend you set up proc files if you write a driver and want to get a running status or register dumps. The API is found in ``<sound/info.h>``. -To create a proc file, call :c:func:`snd_card_proc_new()`. - -:: +To create a proc file, call :c:func:`snd_card_proc_new()`:: struct snd_info_entry *entry; int err = snd_card_proc_new(card, "my-file", &entry); @@ -3859,79 +3638,66 @@ automatically in the card registration and release functions. When the creation is successful, the function stores a new instance in the pointer given in the third argument. It is initialized as a text proc file for read only. To use this proc file as a read-only text file -as it is, set the read callback with a private data via -:c:func:`snd_info_set_text_ops()`. - -:: +as-is, set the read callback with private data via +:c:func:`snd_info_set_text_ops()`:: snd_info_set_text_ops(entry, chip, my_proc_read); where the second argument (``chip``) is the private data to be used in -the callbacks. The third parameter specifies the read buffer size and +the callback. The third parameter specifies the read buffer size and the fourth (``my_proc_read``) is the callback function, which is -defined like - -:: +defined like:: static void my_proc_read(struct snd_info_entry *entry, struct snd_info_buffer *buffer); In the read callback, use :c:func:`snd_iprintf()` for output strings, which works just like normal :c:func:`printf()`. For -example, - -:: +example:: static void my_proc_read(struct snd_info_entry *entry, struct snd_info_buffer *buffer) { struct my_chip *chip = entry->private_data; snd_iprintf(buffer, "This is my chip!\n"); snd_iprintf(buffer, "Port = %ld\n", chip->port); } -The file permissions can be changed afterwards. As default, it's set as +The file permissions can be changed afterwards. By default, they are read only for all users. If you want to add write permission for the -user (root as default), do as follows: - -:: +user (root by default), do as follows:: entry->mode = S_IFREG | S_IRUGO | S_IWUSR; -and set the write buffer size and the callback - -:: +and set the write buffer size and the callback:: entry->c.text.write = my_proc_write; -For the write callback, you can use :c:func:`snd_info_get_line()` +In the write callback, you can use :c:func:`snd_info_get_line()` to get a text line, and :c:func:`snd_info_get_str()` to retrieve a string from the line. Some examples are found in ``core/oss/mixer_oss.c``, core/oss/and ``pcm_oss.c``. -For a raw-data proc-file, set the attributes as follows: - -:: +For a raw-data proc-file, set the attributes as follows:: static const struct snd_info_entry_ops my_file_io_ops = { .read = my_file_io_read, }; entry->content = SNDRV_INFO_CONTENT_DATA; entry->private_data = chip; entry->c.ops = &my_file_io_ops; entry->size = 4096; entry->mode = S_IFREG | S_IRUGO; -For the raw data, ``size`` field must be set properly. This specifies +For raw data, ``size`` field must be set properly. This specifies the maximum size of the proc file access. The read/write callbacks of raw mode are more direct than the text mode. You need to use a low-level I/O functions such as -:c:func:`copy_from_user()` and :c:func:`copy_to_user()` to transfer the data. - -:: +:c:func:`copy_from_user()` and :c:func:`copy_to_user()` to transfer the +data:: static ssize_t my_file_io_read(struct snd_info_entry *entry, void *file_private_data, @@ -3956,37 +3722,33 @@ Power Management If the chip is supposed to work with suspend/resume functions, you need to add power-management code to the driver. The additional code for power-management should be ifdef-ed with ``CONFIG_PM``, or annotated -with __maybe_unused attribute; otherwise the compiler will complain -you. +with __maybe_unused attribute; otherwise the compiler will complain. If the driver *fully* supports suspend/resume that is, the device can be properly resumed to its state when suspend was called, you can set the -``SNDRV_PCM_INFO_RESUME`` flag in the pcm info field. Usually, this is +``SNDRV_PCM_INFO_RESUME`` flag in the PCM info field. Usually, this is possible when the registers of the chip can be safely saved and restored to RAM. If this is set, the trigger callback is called with ``SNDRV_PCM_TRIGGER_RESUME`` after the resume callback completes. Even if the driver doesn't support PM fully but partial suspend/resume is still possible, it's still worthy to implement suspend/resume callbacks. In such a case, applications would reset the status by calling :c:func:`snd_pcm_prepare()` and restart the stream appropriately. Hence, you can define suspend/resume callbacks below but -don't set ``SNDRV_PCM_INFO_RESUME`` info flag to the PCM. +don't set the ``SNDRV_PCM_INFO_RESUME`` info flag to the PCM. Note that the trigger with SUSPEND can always be called when :c:func:`snd_pcm_suspend_all()` is called, regardless of the ``SNDRV_PCM_INFO_RESUME`` flag. The ``RESUME`` flag affects only the behavior of :c:func:`snd_pcm_resume()`. (Thus, in theory, ``SNDRV_PCM_TRIGGER_RESUME`` isn't needed to be handled in the trigger callback when no ``SNDRV_PCM_INFO_RESUME`` flag is set. But, it's better to keep it for compatibility reasons.) -In the earlier version of ALSA drivers, a common power-management layer -was provided, but it has been removed. The driver needs to define the +The driver needs to define the suspend/resume hooks according to the bus the device is connected to. In -the case of PCI drivers, the callbacks look like below: - -:: +the case of PCI drivers, the callbacks look like below:: static int __maybe_unused snd_my_suspend(struct device *dev) { @@ -3999,7 +3761,7 @@ the case of PCI drivers, the callbacks look like below: return 0; } -The scheme of the real suspend job is as follows. +The scheme of the real suspend job is as follows: 1. Retrieve the card and the chip data. @@ -4013,9 +3775,7 @@ The scheme of the real suspend job is as follows. 5. Stop the hardware if necessary. -A typical code would be like: - -:: +Typical code would look like:: static int __maybe_unused mychip_suspend(struct device *dev) { @@ -4034,24 +3794,22 @@ A typical code would be like: } -The scheme of the real resume job is as follows. +The scheme of the real resume job is as follows: 1. Retrieve the card and the chip data. 2. Re-initialize the chip. 3. Restore the saved registers if necessary. -4. Resume the mixer, e.g. calling :c:func:`snd_ac97_resume()`. +4. Resume the mixer, e.g. by calling :c:func:`snd_ac97_resume()`. 5. Restart the hardware (if any). 6. Call :c:func:`snd_power_change_state()` with ``SNDRV_CTL_POWER_D0`` to notify the processes. -A typical code would be like: - -:: +Typical code would look like:: static int __maybe_unused mychip_resume(struct pci_dev *pci) { @@ -4078,9 +3836,7 @@ been already suspended via its own PM ops calling OK, we have all callbacks now. Let's set them up. In the initialization of the card, make sure that you can get the chip data from the card instance, typically via ``private_data`` field, in case you created the -chip data individually. - -:: +chip data individually:: static int snd_mychip_probe(struct pci_dev *pci, const struct pci_device_id *pci_id) @@ -4100,9 +3856,7 @@ chip data individually. } When you created the chip data with :c:func:`snd_card_new()`, it's -anyway accessible via ``private_data`` field. - -:: +anyway accessible via ``private_data`` field:: static int snd_mychip_probe(struct pci_dev *pci, const struct pci_device_id *pci_id) @@ -4119,14 +3873,12 @@ anyway accessible via ``private_data`` field. .... } -If you need a space to save the registers, allocate the buffer for it +If you need space to save the registers, allocate the buffer for it here, too, since it would be fatal if you cannot allocate a memory in the suspend phase. The allocated buffer should be released in the corresponding destructor. -And next, set suspend/resume callbacks to the pci_driver. - -:: +And next, set suspend/resume callbacks to the pci_driver:: static SIMPLE_DEV_PM_OPS(snd_my_pm_ops, mychip_suspend, mychip_resume); @@ -4146,9 +3898,7 @@ have the ``index``, ``id`` and ``enable`` options. If the module supports multiple cards (usually up to 8 = ``SNDRV_CARDS`` cards), they should be arrays. The default initial values are defined -already as constants for easier programming: - -:: +already as constants for easier programming:: static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX; static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR; @@ -4162,9 +3912,7 @@ The module parameters must be declared with the standard ``module_param()``, ``module_param_array()`` and :c:func:`MODULE_PARM_DESC()` macros. -The typical coding would be like below: - -:: +Typical code would look as below:: #define CARD_NAME "My Chip" @@ -4177,9 +3925,7 @@ The typical coding would be like below: Also, don't forget to define the module description and the license. Especially, the recent modprobe requires to define the -module license as GPL, etc., otherwise the system is shown as “tainted”. - -:: +module license as GPL, etc., otherwise the system is shown as “tainted”:: MODULE_DESCRIPTION("Sound driver for My Chip"); MODULE_LICENSE("GPL"); @@ -4242,50 +3988,50 @@ Driver with A Single Source File 1. Modify sound/pci/Makefile - Suppose you have a file xyz.c. Add the following two lines - -:: + Suppose you have a file xyz.c. Add the following two lines:: snd-xyz-objs := xyz.o obj-$(CONFIG_SND_XYZ) += snd-xyz.o 2. Create the Kconfig entry - Add the new entry of Kconfig for your xyz driver. config SND_XYZ - tristate "Foobar XYZ" depends on SND select SND_PCM help Say Y here - to include support for Foobar XYZ soundcard. To compile this driver - as a module, choose M here: the module will be called snd-xyz. the - line, select SND_PCM, specifies that the driver xyz supports PCM. In - addition to SND_PCM, the following components are supported for - select command: SND_RAWMIDI, SND_TIMER, SND_HWDEP, - SND_MPU401_UART, SND_OPL3_LIB, SND_OPL4_LIB, SND_VX_LIB, - SND_AC97_CODEC. Add the select command for each supported - component. + Add the new entry of Kconfig for your xyz driver:: - Note that some selections imply the lowlevel selections. For example, - PCM includes TIMER, MPU401_UART includes RAWMIDI, AC97_CODEC - includes PCM, and OPL3_LIB includes HWDEP. You don't need to give - the lowlevel selections again. + config SND_XYZ + tristate "Foobar XYZ" + depends on SND + select SND_PCM + help + Say Y here to include support for Foobar XYZ soundcard. + To compile this driver as a module, choose M here: + the module will be called snd-xyz. - For the details of Kconfig script, refer to the kbuild documentation. +The line ``select SND_PCM`` specifies that the driver xyz supports PCM. +In addition to SND_PCM, the following components are supported for +select command: SND_RAWMIDI, SND_TIMER, SND_HWDEP, SND_MPU401_UART, +SND_OPL3_LIB, SND_OPL4_LIB, SND_VX_LIB, SND_AC97_CODEC. +Add the select command for each supported component. + +Note that some selections imply the lowlevel selections. For example, +PCM includes TIMER, MPU401_UART includes RAWMIDI, AC97_CODEC +includes PCM, and OPL3_LIB includes HWDEP. You don't need to give +the lowlevel selections again. + +For the details of Kconfig script, refer to the kbuild documentation. Drivers with Several Source Files --------------------------------- Suppose that the driver snd-xyz have several source files. They are located in the new subdirectory, sound/pci/xyz. 1. Add a new directory (``sound/pci/xyz``) in ``sound/pci/Makefile`` - as below - -:: + as below:: obj-$(CONFIG_SND) += sound/pci/xyz/ -2. Under the directory ``sound/pci/xyz``, create a Makefile - -:: +2. Under the directory ``sound/pci/xyz``, create a Makefile:: snd-xyz-objs := xyz.o abc.o def.o obj-$(CONFIG_SND_XYZ) += snd-xyz.o -- 2.40.0.152.g15d061e6df

2 1

[PATCH AUTOSEL 4.19 2/2] ASoC: Intel: bytcr_rt5640: Add quirk for the Acer Iconia One 7 B1-750
by Sasha Levin 20 Apr '23

20 Apr '23

From: Hans de Goede <hdegoede(a)redhat.com> [ Upstream commit e38c5e80c3d293a883c6f1d553f2146ec0bda35e ] The Acer Iconia One 7 B1-750 tablet mostly works fine with the defaults for an Bay Trail CR tablet. Except for the internal mic, instead of an analog mic on IN3 a digital mic on DMIC1 is uses. Add a quirk with these settings for this tablet. Acked-by: Pierre-Louis Bossart <pierre-louis.bossart(a)linux.intel.com> Signed-off-by: Hans de Goede <hdegoede(a)redhat.com> Link: https://lore.kernel.org/r/20230322145332.131525-1-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie(a)kernel.org> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- sound/soc/intel/boards/bytcr_rt5640.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/sound/soc/intel/boards/bytcr_rt5640.c b/sound/soc/intel/boards/bytcr_rt5640.c index 2001bc774c643..d27dd170bedaf 100644 --- a/sound/soc/intel/boards/bytcr_rt5640.c +++ b/sound/soc/intel/boards/bytcr_rt5640.c @@ -400,6 +400,18 @@ static int byt_rt5640_aif1_hw_params(struct snd_pcm_substream *substream, /* Please keep this list alphabetically sorted */ static const struct dmi_system_id byt_rt5640_quirk_table[] = { + { /* Acer Iconia One 7 B1-750 */ + .matches = { + DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Insyde"), + DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "VESPA2"), + }, + .driver_data = (void *)(BYT_RT5640_DMIC1_MAP | + BYT_RT5640_JD_SRC_JD1_IN4P | + BYT_RT5640_OVCD_TH_1500UA | + BYT_RT5640_OVCD_SF_0P75 | + BYT_RT5640_SSP0_AIF1 | + BYT_RT5640_MCLK_EN), + }, { /* Acer Iconia Tab 8 W1-810 */ .matches = { DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Acer"), -- 2.39.2

1 0

[PATCH AUTOSEL 5.4 2/2] ASoC: Intel: bytcr_rt5640: Add quirk for the Acer Iconia One 7 B1-750
by Sasha Levin 20 Apr '23

20 Apr '23

From: Hans de Goede <hdegoede(a)redhat.com> [ Upstream commit e38c5e80c3d293a883c6f1d553f2146ec0bda35e ] The Acer Iconia One 7 B1-750 tablet mostly works fine with the defaults for an Bay Trail CR tablet. Except for the internal mic, instead of an analog mic on IN3 a digital mic on DMIC1 is uses. Add a quirk with these settings for this tablet. Acked-by: Pierre-Louis Bossart <pierre-louis.bossart(a)linux.intel.com> Signed-off-by: Hans de Goede <hdegoede(a)redhat.com> Link: https://lore.kernel.org/r/20230322145332.131525-1-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie(a)kernel.org> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- sound/soc/intel/boards/bytcr_rt5640.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/sound/soc/intel/boards/bytcr_rt5640.c b/sound/soc/intel/boards/bytcr_rt5640.c index 6a8edb0a559de..df3b370fe7292 100644 --- a/sound/soc/intel/boards/bytcr_rt5640.c +++ b/sound/soc/intel/boards/bytcr_rt5640.c @@ -391,6 +391,18 @@ static int byt_rt5640_aif1_hw_params(struct snd_pcm_substream *substream, /* Please keep this list alphabetically sorted */ static const struct dmi_system_id byt_rt5640_quirk_table[] = { + { /* Acer Iconia One 7 B1-750 */ + .matches = { + DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Insyde"), + DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "VESPA2"), + }, + .driver_data = (void *)(BYT_RT5640_DMIC1_MAP | + BYT_RT5640_JD_SRC_JD1_IN4P | + BYT_RT5640_OVCD_TH_1500UA | + BYT_RT5640_OVCD_SF_0P75 | + BYT_RT5640_SSP0_AIF1 | + BYT_RT5640_MCLK_EN), + }, { /* Acer Iconia Tab 8 W1-810 */ .matches = { DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Acer"), -- 2.39.2

1 0

[PATCH AUTOSEL 5.15 1/7] ASOC: Intel: sof_sdw: add quirk for Intel 'Rooks County' NUC M15
by Sasha Levin 20 Apr '23

20 Apr '23

From: Eugene Huang <eugene.huang99(a)gmail.com> [ Upstream commit 3c728b1bc5b99c5275ac5c7788ef814c0e51ef54 ] Same quirks as the 'Bishop County' NUC M15, except the rt711 is in the 'JD2 100K' jack detection mode. Link: https://github.com/thesofproject/linux/issues/4088 Signed-off-by: Eugene Huang <eugene.huang99(a)gmail.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart(a)linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi(a)linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao(a)linux.intel.com> Link: https://lore.kernel.org/r/20230314090553.498664-2-yung-chuan.liao@linux.int… Signed-off-by: Mark Brown <broonie(a)kernel.org> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- sound/soc/intel/boards/sof_sdw.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/sound/soc/intel/boards/sof_sdw.c b/sound/soc/intel/boards/sof_sdw.c index 2d53a707aff9c..089b6c7994f9a 100644 --- a/sound/soc/intel/boards/sof_sdw.c +++ b/sound/soc/intel/boards/sof_sdw.c @@ -212,6 +212,17 @@ static const struct dmi_system_id sof_sdw_quirk_table[] = { SOF_SDW_PCH_DMIC | RT711_JD1), }, + { + /* NUC15 'Rooks County' LAPRC510 and LAPRC710 skews */ + .callback = sof_sdw_quirk_cb, + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Intel(R) Client Systems"), + DMI_MATCH(DMI_PRODUCT_NAME, "LAPRC"), + }, + .driver_data = (void *)(SOF_SDW_TGL_HDMI | + SOF_SDW_PCH_DMIC | + RT711_JD2_100K), + }, /* TigerLake-SDCA devices */ { .callback = sof_sdw_quirk_cb, -- 2.39.2

1 2

[PATCH AUTOSEL 6.1 01/15] ASOC: Intel: sof_sdw: add quirk for Intel 'Rooks County' NUC M15
by Sasha Levin 20 Apr '23

20 Apr '23

From: Eugene Huang <eugene.huang99(a)gmail.com> [ Upstream commit 3c728b1bc5b99c5275ac5c7788ef814c0e51ef54 ] Same quirks as the 'Bishop County' NUC M15, except the rt711 is in the 'JD2 100K' jack detection mode. Link: https://github.com/thesofproject/linux/issues/4088 Signed-off-by: Eugene Huang <eugene.huang99(a)gmail.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart(a)linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi(a)linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao(a)linux.intel.com> Link: https://lore.kernel.org/r/20230314090553.498664-2-yung-chuan.liao@linux.int… Signed-off-by: Mark Brown <broonie(a)kernel.org> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- sound/soc/intel/boards/sof_sdw.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/sound/soc/intel/boards/sof_sdw.c b/sound/soc/intel/boards/sof_sdw.c index ee9857dc3135d..d4f92bb5e29f8 100644 --- a/sound/soc/intel/boards/sof_sdw.c +++ b/sound/soc/intel/boards/sof_sdw.c @@ -213,6 +213,17 @@ static const struct dmi_system_id sof_sdw_quirk_table[] = { SOF_SDW_PCH_DMIC | RT711_JD1), }, + { + /* NUC15 'Rooks County' LAPRC510 and LAPRC710 skews */ + .callback = sof_sdw_quirk_cb, + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Intel(R) Client Systems"), + DMI_MATCH(DMI_PRODUCT_NAME, "LAPRC"), + }, + .driver_data = (void *)(SOF_SDW_TGL_HDMI | + SOF_SDW_PCH_DMIC | + RT711_JD2_100K), + }, /* TigerLake-SDCA devices */ { .callback = sof_sdw_quirk_cb, -- 2.39.2

1 5

[PATCH AUTOSEL 6.2 01/17] ASOC: Intel: sof_sdw: add quirk for Intel 'Rooks County' NUC M15
by Sasha Levin 20 Apr '23

20 Apr '23

From: Eugene Huang <eugene.huang99(a)gmail.com> [ Upstream commit 3c728b1bc5b99c5275ac5c7788ef814c0e51ef54 ] Same quirks as the 'Bishop County' NUC M15, except the rt711 is in the 'JD2 100K' jack detection mode. Link: https://github.com/thesofproject/linux/issues/4088 Signed-off-by: Eugene Huang <eugene.huang99(a)gmail.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart(a)linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi(a)linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao(a)linux.intel.com> Link: https://lore.kernel.org/r/20230314090553.498664-2-yung-chuan.liao@linux.int… Signed-off-by: Mark Brown <broonie(a)kernel.org> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- sound/soc/intel/boards/sof_sdw.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/sound/soc/intel/boards/sof_sdw.c b/sound/soc/intel/boards/sof_sdw.c index d2ed807abde95..767fa89d08708 100644 --- a/sound/soc/intel/boards/sof_sdw.c +++ b/sound/soc/intel/boards/sof_sdw.c @@ -213,6 +213,17 @@ static const struct dmi_system_id sof_sdw_quirk_table[] = { SOF_SDW_PCH_DMIC | RT711_JD1), }, + { + /* NUC15 'Rooks County' LAPRC510 and LAPRC710 skews */ + .callback = sof_sdw_quirk_cb, + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Intel(R) Client Systems"), + DMI_MATCH(DMI_PRODUCT_NAME, "LAPRC"), + }, + .driver_data = (void *)(SOF_SDW_TGL_HDMI | + SOF_SDW_PCH_DMIC | + RT711_JD2_100K), + }, /* TigerLake-SDCA devices */ { .callback = sof_sdw_quirk_cb, -- 2.39.2

1 5

[PATCH v2] ASoC: rt722-sdca: Add RT722 SDCA driver
by Jack Yu 20 Apr '23

20 Apr '23

This is the initial codec driver for rt722-sdca. Patch v2 is to fix warning message from kernel test robot. Signed-off-by: Jack Yu <jack.yu(a)realtek.com> --- sound/soc/codecs/Kconfig | 7 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/rt722-sdca-sdw.c | 505 ++++++++++ sound/soc/codecs/rt722-sdca-sdw.h | 124 +++ sound/soc/codecs/rt722-sdca.c | 1549 +++++++++++++++++++++++++++++ sound/soc/codecs/rt722-sdca.h | 237 +++++ 6 files changed, 2424 insertions(+) create mode 100644 sound/soc/codecs/rt722-sdca-sdw.c create mode 100644 sound/soc/codecs/rt722-sdca-sdw.h create mode 100644 sound/soc/codecs/rt722-sdca.c create mode 100644 sound/soc/codecs/rt722-sdca.h diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 79d2362ad055..a163e2afdf72 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -207,6 +207,7 @@ config SND_SOC_ALL_CODECS imply SND_SOC_RT712_SDCA_DMIC_SDW imply SND_SOC_RT715_SDW imply SND_SOC_RT715_SDCA_SDW + imply SND_SOC_RT722_SDCA_SDW imply SND_SOC_RT1308_SDW imply SND_SOC_RT1316_SDW imply SND_SOC_RT1318_SDW @@ -1539,6 +1540,12 @@ config SND_SOC_RT712_SDCA_DMIC_SDW select REGMAP_SOUNDWIRE select REGMAP_SOUNDWIRE_MBQ +config SND_SOC_RT722_SDCA_SDW + tristate "Realtek RT722 SDCA Codec - SDW" + depends on SOUNDWIRE + select REGMAP_SOUNDWIRE + select REGMAP_SOUNDWIRE_MBQ + config SND_SOC_RT715 tristate diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 5cdbae88e6e3..cd799306331c 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -237,6 +237,7 @@ snd-soc-rt712-sdca-objs := rt712-sdca.o rt712-sdca-sdw.o snd-soc-rt712-sdca-dmic-objs := rt712-sdca-dmic.o snd-soc-rt715-objs := rt715.o rt715-sdw.o snd-soc-rt715-sdca-objs := rt715-sdca.o rt715-sdca-sdw.o +snd-soc-rt722-sdca-objs := rt722-sdca.o rt722-sdca-sdw.o snd-soc-rt9120-objs := rt9120.o snd-soc-sdw-mockup-objs := sdw-mockup.o snd-soc-sgtl5000-objs := sgtl5000.o @@ -607,6 +608,7 @@ obj-$(CONFIG_SND_SOC_RT712_SDCA_SDW) += snd-soc-rt712-sdca.o obj-$(CONFIG_SND_SOC_RT712_SDCA_DMIC_SDW) += snd-soc-rt712-sdca-dmic.o obj-$(CONFIG_SND_SOC_RT715) += snd-soc-rt715.o obj-$(CONFIG_SND_SOC_RT715_SDCA_SDW) += snd-soc-rt715-sdca.o +obj-$(CONFIG_SND_SOC_RT722_SDCA_SDW) += snd-soc-rt722-sdca.o obj-$(CONFIG_SND_SOC_RT9120) += snd-soc-rt9120.o obj-$(CONFIG_SND_SOC_SDW_MOCKUP) += snd-soc-sdw-mockup.o obj-$(CONFIG_SND_SOC_SGTL5000) += snd-soc-sgtl5000.o diff --git a/sound/soc/codecs/rt722-sdca-sdw.c b/sound/soc/codecs/rt722-sdca-sdw.c new file mode 100644 index 000000000000..9e2dd5bc59ac --- /dev/null +++ b/sound/soc/codecs/rt722-sdca-sdw.c @@ -0,0 +1,505 @@ +// SPDX-License-Identifier: GPL-2.0-only +// +// rt722-sdca-sdw.c -- rt722 SDCA ALSA SoC audio driver +// +// Copyright(c) 2023 Realtek Semiconductor Corp. +// +// + +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/module.h> +#include <linux/mod_devicetable.h> +#include <linux/pm_runtime.h> +#include <linux/soundwire/sdw_registers.h> + +#include "rt722-sdca.h" +#include "rt722-sdca-sdw.h" + +static bool rt722_sdca_readable_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x2f01 ... 0x2f0a: + case 0x2f35 ... 0x2f36: + case 0x2f50: + case 0x2f54: + case 0x2f58 ... 0x2f5d: + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, RT722_SDCA_CTL_SELECTED_MODE, + 0): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, RT722_SDCA_CTL_DETECTED_MODE, + 0): + case SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, RT722_SDCA_CTL_HIDTX_CURRENT_OWNER, + 0) ... SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_MESSAGE_LENGTH, 0): + case RT722_BUF_ADDR_HID1 ... RT722_BUF_ADDR_HID2: + return true; + default: + return false; + } +} + +static bool rt722_sdca_volatile_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x2f01: + case 0x2f54: + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, RT722_SDCA_CTL_DETECTED_MODE, + 0): + case SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, RT722_SDCA_CTL_HIDTX_CURRENT_OWNER, + 0) ... SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_MESSAGE_LENGTH, 0): + case RT722_BUF_ADDR_HID1 ... RT722_BUF_ADDR_HID2: + return true; + default: + return false; + } +} + +static bool rt722_sdca_mbq_readable_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x2000000 ... 0x2000024: + case 0x2000029 ... 0x200004a: + case 0x2000051 ... 0x2000052: + case 0x200005a ... 0x200005b: + case 0x2000061 ... 0x2000069: + case 0x200006b: + case 0x2000070: + case 0x200007f: + case 0x2000082 ... 0x200008e: + case 0x2000090 ... 0x2000094: + case 0x5300000 ... 0x5300002: + case 0x5400002: + case 0x5600000 ... 0x5600007: + case 0x5700000 ... 0x5700004: + case 0x5800000 ... 0x5800004: + case 0x5b00003: + case 0x5c00011: + case 0x5d00006: + case 0x5f00000 ... 0x5f0000d: + case 0x5f00030: + case 0x6100000 ... 0x6100051: + case 0x6100055 ... 0x6100057: + case 0x6100062: + case 0x6100064 ... 0x6100065: + case 0x6100067: + case 0x6100070 ... 0x610007c: + case 0x6100080: + case SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_01): + case SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_02): + case SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_03): + case SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_04): + case SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_VOLUME, CH_L): + case SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_VOLUME, CH_R): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_VOLUME, + CH_L): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_VOLUME, + CH_R): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_VOLUME, + CH_L): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_VOLUME, + CH_R): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, + RT722_SDCA_CTL_FU_CH_GAIN, CH_L): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, + RT722_SDCA_CTL_FU_CH_GAIN, CH_R): + return true; + default: + return false; + } +} + +static bool rt722_sdca_mbq_volatile_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x2000000: + case 0x200000d: + case 0x2000019: + case 0x2000020: + case 0x2000030: + case 0x2000046: + case 0x2000067: + case 0x2000084: + case 0x2000086: + return true; + default: + return false; + } +} + +static const struct regmap_config rt722_sdca_regmap = { + .reg_bits = 32, + .val_bits = 8, + .readable_reg = rt722_sdca_readable_register, + .volatile_reg = rt722_sdca_volatile_register, + .max_register = 0x44ffffff, + .reg_defaults = rt722_sdca_reg_defaults, + .num_reg_defaults = ARRAY_SIZE(rt722_sdca_reg_defaults), + .cache_type = REGCACHE_RBTREE, + .use_single_read = true, + .use_single_write = true, +}; + +static const struct regmap_config rt722_sdca_mbq_regmap = { + .name = "sdw-mbq", + .reg_bits = 32, + .val_bits = 16, + .readable_reg = rt722_sdca_mbq_readable_register, + .volatile_reg = rt722_sdca_mbq_volatile_register, + .max_register = 0x41000312, + .reg_defaults = rt722_sdca_mbq_defaults, + .num_reg_defaults = ARRAY_SIZE(rt722_sdca_mbq_defaults), + .cache_type = REGCACHE_RBTREE, + .use_single_read = true, + .use_single_write = true, +}; + +static int rt722_sdca_update_status(struct sdw_slave *slave, + enum sdw_slave_status status) +{ + struct rt722_sdca_priv *rt722 = dev_get_drvdata(&slave->dev); + + /* Update the status */ + rt722->status = status; + + if (status == SDW_SLAVE_UNATTACHED) + rt722->hw_init = false; + + if (status == SDW_SLAVE_ATTACHED) { + if (rt722->hs_jack) { + /* + * Due to the SCP_SDCA_INTMASK will be cleared by any reset, and then + * if the device attached again, we will need to set the setting back. + * It could avoid losing the jack detection interrupt. + * This also could sync with the cache value as the rt722_sdca_jack_init set. + */ + sdw_write_no_pm(rt722->slave, SDW_SCP_SDCA_INTMASK1, + SDW_SCP_SDCA_INTMASK_SDCA_0 | SDW_SCP_SDCA_INTMASK_SDCA_6); + sdw_write_no_pm(rt722->slave, SDW_SCP_SDCA_INTMASK2, + SDW_SCP_SDCA_INTMASK_SDCA_8); + } + } + + /* + * Perform initialization only if slave status is present and + * hw_init flag is false + */ + if (rt722->hw_init || rt722->status != SDW_SLAVE_ATTACHED) + return 0; + + /* perform I/O transfers required for Slave initialization */ + return rt722_sdca_io_init(&slave->dev, slave); +} + +static int rt722_sdca_read_prop(struct sdw_slave *slave) +{ + struct sdw_slave_prop *prop = &slave->prop; + int nval; + int i, j; + u32 bit; + unsigned long addr; + struct sdw_dpn_prop *dpn; + + prop->scp_int1_mask = SDW_SCP_INT1_BUS_CLASH | SDW_SCP_INT1_PARITY; + prop->quirks = SDW_SLAVE_QUIRKS_INVALID_INITIAL_PARITY; + + prop->paging_support = true; + + /* first we need to allocate memory for set bits in port lists */ + prop->source_ports = BIT(6) | BIT(2); /* BITMAP: 01000100 */ + prop->sink_ports = BIT(3) | BIT(1); /* BITMAP: 00001010 */ + + nval = hweight32(prop->source_ports); + prop->src_dpn_prop = devm_kcalloc(&slave->dev, nval, + sizeof(*prop->src_dpn_prop), GFP_KERNEL); + if (!prop->src_dpn_prop) + return -ENOMEM; + + i = 0; + dpn = prop->src_dpn_prop; + addr = prop->source_ports; + for_each_set_bit(bit, &addr, 32) { + dpn[i].num = bit; + dpn[i].type = SDW_DPN_FULL; + dpn[i].simple_ch_prep_sm = true; + dpn[i].ch_prep_timeout = 10; + i++; + } + + /* do this again for sink now */ + nval = hweight32(prop->sink_ports); + prop->sink_dpn_prop = devm_kcalloc(&slave->dev, nval, + sizeof(*prop->sink_dpn_prop), GFP_KERNEL); + if (!prop->sink_dpn_prop) + return -ENOMEM; + + j = 0; + dpn = prop->sink_dpn_prop; + addr = prop->sink_ports; + for_each_set_bit(bit, &addr, 32) { + dpn[j].num = bit; + dpn[j].type = SDW_DPN_FULL; + dpn[j].simple_ch_prep_sm = true; + dpn[j].ch_prep_timeout = 10; + j++; + } + + /* set the timeout values */ + prop->clk_stop_timeout = 200; + + /* wake-up event */ + prop->wake_capable = 1; + + return 0; +} + +static int rt722_sdca_interrupt_callback(struct sdw_slave *slave, + struct sdw_slave_intr_status *status) +{ + struct rt722_sdca_priv *rt722 = dev_get_drvdata(&slave->dev); + int ret, stat; + int count = 0, retry = 3; + unsigned int sdca_cascade, scp_sdca_stat1, scp_sdca_stat2 = 0; + + if (cancel_delayed_work_sync(&rt722->jack_detect_work)) { + dev_warn(&slave->dev, "%s the pending delayed_work was cancelled", __func__); + /* avoid the HID owner doesn't change to device */ + if (rt722->scp_sdca_stat2) + scp_sdca_stat2 = rt722->scp_sdca_stat2; + } + + /* + * The critical section below intentionally protects a rather large piece of code. + * We don't want to allow the system suspend to disable an interrupt while we are + * processing it, which could be problematic given the quirky SoundWire interrupt + * scheme. We do want however to prevent new workqueues from being scheduled if + * the disable_irq flag was set during system suspend. + */ + mutex_lock(&rt722->disable_irq_lock); + + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT1); + if (ret < 0) + goto io_error; + rt722->scp_sdca_stat1 = ret; + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT2); + if (ret < 0) + goto io_error; + rt722->scp_sdca_stat2 = ret; + if (scp_sdca_stat2) + rt722->scp_sdca_stat2 |= scp_sdca_stat2; + do { + /* clear flag */ + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT1); + if (ret < 0) + goto io_error; + if (ret & SDW_SCP_SDCA_INTMASK_SDCA_0) { + ret = sdw_update_no_pm(rt722->slave, SDW_SCP_SDCA_INT1, + SDW_SCP_SDCA_INT_SDCA_0, SDW_SCP_SDCA_INT_SDCA_0); + if (ret < 0) + goto io_error; + } else if (ret & SDW_SCP_SDCA_INTMASK_SDCA_6) { + ret = sdw_update_no_pm(rt722->slave, SDW_SCP_SDCA_INT1, + SDW_SCP_SDCA_INT_SDCA_6, SDW_SCP_SDCA_INT_SDCA_6); + if (ret < 0) + goto io_error; + } + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT2); + if (ret < 0) + goto io_error; + if (ret & SDW_SCP_SDCA_INTMASK_SDCA_8) { + ret = sdw_write_no_pm(rt722->slave, SDW_SCP_SDCA_INT2, + SDW_SCP_SDCA_INTMASK_SDCA_8); + if (ret < 0) + goto io_error; + } + + /* check if flag clear or not */ + ret = sdw_read_no_pm(rt722->slave, SDW_DP0_INT); + if (ret < 0) + goto io_error; + sdca_cascade = ret & SDW_DP0_SDCA_CASCADE; + + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT1); + if (ret < 0) + goto io_error; + scp_sdca_stat1 = ret & SDW_SCP_SDCA_INTMASK_SDCA_0; + + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT2); + if (ret < 0) + goto io_error; + scp_sdca_stat2 = ret & SDW_SCP_SDCA_INTMASK_SDCA_8; + + stat = scp_sdca_stat1 || scp_sdca_stat2 || sdca_cascade; + + count++; + } while (stat != 0 && count < retry); + + if (stat) + dev_warn(&slave->dev, + "%s scp_sdca_stat1=0x%x, scp_sdca_stat2=0x%x\n", __func__, + rt722->scp_sdca_stat1, rt722->scp_sdca_stat2); + + if (status->sdca_cascade && !rt722->disable_irq) + mod_delayed_work(system_power_efficient_wq, + &rt722->jack_detect_work, msecs_to_jiffies(30)); + + mutex_unlock(&rt722->disable_irq_lock); + + return 0; + +io_error: + mutex_unlock(&rt722->disable_irq_lock); + pr_err_ratelimited("IO error in %s, ret %d\n", __func__, ret); + return ret; +} + +static struct sdw_slave_ops rt722_sdca_slave_ops = { + .read_prop = rt722_sdca_read_prop, + .interrupt_callback = rt722_sdca_interrupt_callback, + .update_status = rt722_sdca_update_status, +}; + +static int rt722_sdca_sdw_probe(struct sdw_slave *slave, + const struct sdw_device_id *id) +{ + struct regmap *regmap, *mbq_regmap; + + /* Regmap Initialization */ + mbq_regmap = devm_regmap_init_sdw_mbq(slave, &rt722_sdca_mbq_regmap); + if (IS_ERR(mbq_regmap)) + return PTR_ERR(mbq_regmap); + + regmap = devm_regmap_init_sdw(slave, &rt722_sdca_regmap); + if (IS_ERR(regmap)) + return PTR_ERR(regmap); + + return rt722_sdca_init(&slave->dev, regmap, mbq_regmap, slave); +} + +static int rt722_sdca_sdw_remove(struct sdw_slave *slave) +{ + struct rt722_sdca_priv *rt722 = dev_get_drvdata(&slave->dev); + + if (rt722->hw_init) { + cancel_delayed_work_sync(&rt722->jack_detect_work); + cancel_delayed_work_sync(&rt722->jack_btn_check_work); + } + + if (rt722->first_hw_init) + pm_runtime_disable(&slave->dev); + + mutex_destroy(&rt722->calibrate_mutex); + mutex_destroy(&rt722->disable_irq_lock); + + return 0; +} + +static const struct sdw_device_id rt722_sdca_id[] = { + SDW_SLAVE_ENTRY_EXT(0x025d, 0x722, 0x3, 0x1, 0), + {}, +}; +MODULE_DEVICE_TABLE(sdw, rt722_sdca_id); + +static int __maybe_unused rt722_sdca_dev_suspend(struct device *dev) +{ + struct rt722_sdca_priv *rt722 = dev_get_drvdata(dev); + + if (!rt722->hw_init) + return 0; + + cancel_delayed_work_sync(&rt722->jack_detect_work); + cancel_delayed_work_sync(&rt722->jack_btn_check_work); + + regcache_cache_only(rt722->regmap, true); + regcache_cache_only(rt722->mbq_regmap, true); + + return 0; +} + +static int __maybe_unused rt722_sdca_dev_system_suspend(struct device *dev) +{ + struct rt722_sdca_priv *rt722_sdca = dev_get_drvdata(dev); + struct sdw_slave *slave = dev_to_sdw_dev(dev); + int ret1, ret2; + + if (!rt722_sdca->hw_init) + return 0; + + /* + * prevent new interrupts from being handled after the + * deferred work completes and before the parent disables + * interrupts on the link + */ + mutex_lock(&rt722_sdca->disable_irq_lock); + rt722_sdca->disable_irq = true; + ret1 = sdw_update_no_pm(slave, SDW_SCP_SDCA_INTMASK1, + SDW_SCP_SDCA_INTMASK_SDCA_0 | SDW_SCP_SDCA_INTMASK_SDCA_6, 0); + ret2 = sdw_update_no_pm(slave, SDW_SCP_SDCA_INTMASK2, + SDW_SCP_SDCA_INTMASK_SDCA_8, 0); + mutex_unlock(&rt722_sdca->disable_irq_lock); + + if (ret1 < 0 || ret2 < 0) { + /* log but don't prevent suspend from happening */ + dev_dbg(&slave->dev, "%s: could not disable SDCA interrupts\n:", __func__); + } + + return rt722_sdca_dev_suspend(dev); +} + +#define RT722_PROBE_TIMEOUT 5000 + +static int __maybe_unused rt722_sdca_dev_resume(struct device *dev) +{ + struct sdw_slave *slave = dev_to_sdw_dev(dev); + struct rt722_sdca_priv *rt722 = dev_get_drvdata(dev); + unsigned long time; + + if (!rt722->first_hw_init) + return 0; + + if (!slave->unattach_request) + goto regmap_sync; + + time = wait_for_completion_timeout(&slave->initialization_complete, + msecs_to_jiffies(RT722_PROBE_TIMEOUT)); + if (!time) { + dev_err(&slave->dev, "Initialization not complete, timed out\n"); + sdw_show_ping_status(slave->bus, true); + + return -ETIMEDOUT; + } + +regmap_sync: + slave->unattach_request = 0; + regcache_cache_only(rt722->regmap, false); + regcache_sync(rt722->regmap); + regcache_cache_only(rt722->mbq_regmap, false); + regcache_sync(rt722->mbq_regmap); + return 0; +} + +static const struct dev_pm_ops rt722_sdca_pm = { + SET_SYSTEM_SLEEP_PM_OPS(rt722_sdca_dev_system_suspend, rt722_sdca_dev_resume) + SET_RUNTIME_PM_OPS(rt722_sdca_dev_suspend, rt722_sdca_dev_resume, NULL) +}; + +static struct sdw_driver rt722_sdca_sdw_driver = { + .driver = { + .name = "rt722-sdca", + .owner = THIS_MODULE, + .pm = &rt722_sdca_pm, + }, + .probe = rt722_sdca_sdw_probe, + .remove = rt722_sdca_sdw_remove, + .ops = &rt722_sdca_slave_ops, + .id_table = rt722_sdca_id, +}; +module_sdw_driver(rt722_sdca_sdw_driver); + +MODULE_DESCRIPTION("ASoC RT722 SDCA SDW driver"); +MODULE_AUTHOR("Jack Yu <jack.yu(a)realtek.com>"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/rt722-sdca-sdw.h b/sound/soc/codecs/rt722-sdca-sdw.h new file mode 100644 index 000000000000..5b43e86f75d1 --- /dev/null +++ b/sound/soc/codecs/rt722-sdca-sdw.h @@ -0,0 +1,124 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * rt722-sdca-sdw.h -- RT722 SDCA ALSA SoC audio driver header + * + * Copyright(c) 2023 Realtek Semiconductor Corp. + */ + +#ifndef __RT722_SDW_H__ +#define __RT722_SDW_H__ + +#include <linux/regmap.h> +#include <linux/soundwire/sdw_registers.h> + +static const struct reg_default rt722_sdca_reg_defaults[] = { + { 0x202d, 0x00 }, + { 0x2f01, 0x00 }, + { 0x2f02, 0x09 }, + { 0x2f03, 0x00 }, + { 0x2f04, 0x00 }, + { 0x2f05, 0x0b }, + { 0x2f06, 0x01 }, + { 0x2f08, 0x00 }, + { 0x2f09, 0x00 }, + { 0x2f0a, 0x00 }, + { 0x2f35, 0x00 }, + { 0x2f36, 0x00 }, + { 0x2f50, 0xf0 }, + { 0x2f58, 0x07 }, + { 0x2f59, 0x07 }, + { 0x2f5a, 0x07 }, + { 0x2f5b, 0x07 }, + { 0x2f5c, 0x27 }, + { 0x2f5d, 0x07 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_CS01, RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, + 0), 0x09 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_CS11, RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, + 0), 0x09 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE12, RT722_SDCA_CTL_REQ_POWER_STATE, + 0), 0x03 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE40, RT722_SDCA_CTL_REQ_POWER_STATE, + 0), 0x03 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_MUTE, CH_L), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_MUTE, CH_R), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_MUTE, CH_L), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_MUTE, CH_R), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_CS1F, RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, + 0), 0x09 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_MUTE, CH_01), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_MUTE, CH_02), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_MUTE, CH_03), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_MUTE, CH_04), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_PDE2A, RT722_SDCA_CTL_REQ_POWER_STATE, 0), + 0x03 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_IT26, RT722_SDCA_CTL_VENDOR_DEF, 0), + 0x00 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_CS31, RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), + 0x09 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_MUTE, CH_L), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_MUTE, CH_R), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_PDE23, RT722_SDCA_CTL_REQ_POWER_STATE, 0), + 0x03 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_OT23, RT722_SDCA_CTL_VENDOR_DEF, 0), 0x00 }, +}; + +static const struct reg_default rt722_sdca_mbq_defaults[] = { + { 0x200003c, 0xc214 }, + { 0x2000046, 0x8004 }, + { 0x6100006, 0x0005 }, + { 0x6100010, 0x2630 }, + { 0x6100011, 0x152f }, + { 0x6100013, 0x0102 }, + { 0x6100015, 0x2200 }, + { 0x6100017, 0x0102 }, + { 0x6100025, 0x2a29 }, + { 0x6100026, 0x2a00 }, + { 0x6100028, 0x2a2a }, + { 0x6100029, 0x4141 }, + { 0x6100055, 0x0000 }, + { 0x5810000, 0x702d }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_VOLUME, + CH_L), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_VOLUME, + CH_R), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_VOLUME, + CH_L), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_VOLUME, + CH_R), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, RT722_SDCA_CTL_FU_CH_GAIN, + CH_L), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, RT722_SDCA_CTL_FU_CH_GAIN, + CH_R), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_01), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_02), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_03), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_04), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15, RT722_SDCA_CTL_FU_CH_GAIN, CH_01), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15, RT722_SDCA_CTL_FU_CH_GAIN, CH_02), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15, RT722_SDCA_CTL_FU_CH_GAIN, CH_03), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15, RT722_SDCA_CTL_FU_CH_GAIN, CH_04), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_VOLUME, CH_L), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_VOLUME, CH_R), + 0x0000 }, +}; + +#endif /* __RT722_SDW_H__ */ diff --git a/sound/soc/codecs/rt722-sdca.c b/sound/soc/codecs/rt722-sdca.c new file mode 100644 index 000000000000..a104c42f9904 --- /dev/null +++ b/sound/soc/codecs/rt722-sdca.c @@ -0,0 +1,1549 @@ +// SPDX-License-Identifier: GPL-2.0-only +// +// rt722-sdca.c -- rt722 SDCA ALSA SoC audio driver +// +// Copyright(c) 2023 Realtek Semiconductor Corp. +// +// + +#include <linux/bitops.h> +#include <sound/core.h> +#include <linux/delay.h> +#include <linux/init.h> +#include <sound/initval.h> +#include <sound/jack.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <sound/pcm.h> +#include <linux/pm_runtime.h> +#include <sound/pcm_params.h> +#include <linux/soundwire/sdw_registers.h> +#include <linux/slab.h> +#include <sound/soc-dapm.h> +#include <sound/tlv.h> + +#include "rt722-sdca.h" + +int rt722_sdca_index_write(struct rt722_sdca_priv *rt722, + unsigned int nid, unsigned int reg, unsigned int value) +{ + struct regmap *regmap = rt722->mbq_regmap; + unsigned int addr = (nid << 20) | reg; + int ret; + + ret = regmap_write(regmap, addr, value); + if (ret < 0) + dev_err(&rt722->slave->dev, + "Failed to set private value: %06x <= %04x ret=%d\n", + addr, value, ret); + + return ret; +} + +int rt722_sdca_index_read(struct rt722_sdca_priv *rt722, + unsigned int nid, unsigned int reg, unsigned int *value) +{ + int ret; + struct regmap *regmap = rt722->mbq_regmap; + unsigned int addr = (nid << 20) | reg; + + ret = regmap_read(regmap, addr, value); + if (ret < 0) + dev_err(&rt722->slave->dev, + "Failed to get private value: %06x => %04x ret=%d\n", + addr, *value, ret); + + return ret; +} + +static int rt722_sdca_index_update_bits(struct rt722_sdca_priv *rt722, + unsigned int nid, unsigned int reg, unsigned int mask, unsigned int val) +{ + unsigned int tmp; + int ret; + + ret = rt722_sdca_index_read(rt722, nid, reg, &tmp); + if (ret < 0) + return ret; + + set_mask_bits(&tmp, mask, val); + return rt722_sdca_index_write(rt722, nid, reg, tmp); +} + +static int rt722_sdca_btn_type(unsigned char *buffer) +{ + if ((*buffer & 0xf0) == 0x10 || (*buffer & 0x0f) == 0x01 || (*(buffer + 1) == 0x01) || + (*(buffer + 1) == 0x10)) + return SND_JACK_BTN_2; + else if ((*buffer & 0xf0) == 0x20 || (*buffer & 0x0f) == 0x02 || (*(buffer + 1) == 0x02) || + (*(buffer + 1) == 0x20)) + return SND_JACK_BTN_3; + else if ((*buffer & 0xf0) == 0x40 || (*buffer & 0x0f) == 0x04 || (*(buffer + 1) == 0x04) || + (*(buffer + 1) == 0x40)) + return SND_JACK_BTN_0; + else if ((*buffer & 0xf0) == 0x80 || (*buffer & 0x0f) == 0x08 || (*(buffer + 1) == 0x08) || + (*(buffer + 1) == 0x80)) + return SND_JACK_BTN_1; + + return 0; +} + +static unsigned int rt722_sdca_button_detect(struct rt722_sdca_priv *rt722) +{ + unsigned int btn_type = 0, offset, idx, val, owner; + int ret; + unsigned char buf[3]; + + /* get current UMP message owner */ + ret = regmap_read(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_CURRENT_OWNER, 0), &owner); + if (ret < 0) + return 0; + + /* if owner is device then there is no button event from device */ + if (owner == 1) + return 0; + + /* read UMP message offset */ + ret = regmap_read(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_MESSAGE_OFFSET, 0), &offset); + if (ret < 0) + goto _end_btn_det_; + + for (idx = 0; idx < sizeof(buf); idx++) { + ret = regmap_read(rt722->regmap, + RT722_BUF_ADDR_HID1 + offset + idx, &val); + if (ret < 0) + goto _end_btn_det_; + buf[idx] = val & 0xff; + } + + if (buf[0] == 0x11) + btn_type = rt722_sdca_btn_type(&buf[1]); + +_end_btn_det_: + /* Host is owner, so set back to device */ + if (owner == 0) + /* set owner to device */ + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_CURRENT_OWNER, 0), 0x01); + + return btn_type; +} + +static int rt722_sdca_headset_detect(struct rt722_sdca_priv *rt722) +{ + unsigned int det_mode; + int ret; + + /* get detected_mode */ + ret = regmap_read(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, + RT722_SDCA_CTL_DETECTED_MODE, 0), &det_mode); + if (ret < 0) + goto io_error; + + switch (det_mode) { + case 0x00: + rt722->jack_type = 0; + break; + case 0x03: + rt722->jack_type = SND_JACK_HEADPHONE; + break; + case 0x05: + rt722->jack_type = SND_JACK_HEADSET; + break; + } + + /* write selected_mode */ + if (det_mode) { + ret = regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, + RT722_SDCA_CTL_SELECTED_MODE, 0), det_mode); + if (ret < 0) + goto io_error; + } + + dev_dbg(&rt722->slave->dev, + "%s, detected_mode=0x%x\n", __func__, det_mode); + + return 0; + +io_error: + pr_err_ratelimited("IO error in %s, ret %d\n", __func__, ret); + return ret; +} + +static void rt722_sdca_jack_detect_handler(struct work_struct *work) +{ + struct rt722_sdca_priv *rt722 = + container_of(work, struct rt722_sdca_priv, jack_detect_work.work); + int btn_type = 0, ret; + + if (!rt722->hs_jack) + return; + + if (!rt722->component->card || !rt722->component->card->instantiated) + return; + + /* SDW_SCP_SDCA_INT_SDCA_6 is used for jack detection */ + if (rt722->scp_sdca_stat1 & SDW_SCP_SDCA_INT_SDCA_6 || + rt722->scp_sdca_stat1 & SDW_SCP_SDCA_INT_SDCA_0) { + ret = rt722_sdca_headset_detect(rt722); + if (ret < 0) + return; + } + + /* SDW_SCP_SDCA_INT_SDCA_8 is used for button detection */ + if (rt722->scp_sdca_stat2 & SDW_SCP_SDCA_INT_SDCA_8) + btn_type = rt722_sdca_button_detect(rt722); + + if (rt722->jack_type == 0) + btn_type = 0; + + dev_dbg(&rt722->slave->dev, + "in %s, jack_type=%d\n", __func__, rt722->jack_type); + dev_dbg(&rt722->slave->dev, + "in %s, btn_type=0x%x\n", __func__, btn_type); + dev_dbg(&rt722->slave->dev, + "in %s, scp_sdca_stat1=0x%x, scp_sdca_stat2=0x%x\n", __func__, + rt722->scp_sdca_stat1, rt722->scp_sdca_stat2); + + snd_soc_jack_report(rt722->hs_jack, rt722->jack_type | btn_type, + SND_JACK_HEADSET | + SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3); + + if (btn_type) { + /* button released */ + snd_soc_jack_report(rt722->hs_jack, rt722->jack_type, + SND_JACK_HEADSET | + SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3); + + mod_delayed_work(system_power_efficient_wq, + &rt722->jack_btn_check_work, msecs_to_jiffies(200)); + } +} + +static void rt722_sdca_btn_check_handler(struct work_struct *work) +{ + struct rt722_sdca_priv *rt722 = + container_of(work, struct rt722_sdca_priv, jack_btn_check_work.work); + int btn_type = 0, ret, idx; + unsigned int det_mode, offset, val; + unsigned char buf[3]; + + ret = regmap_read(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, + RT722_SDCA_CTL_DETECTED_MODE, 0), &det_mode); + if (ret < 0) + goto io_error; + + /* pin attached */ + if (det_mode) { + /* read UMP message offset */ + ret = regmap_read(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_MESSAGE_OFFSET, 0), &offset); + if (ret < 0) + goto io_error; + + for (idx = 0; idx < sizeof(buf); idx++) { + ret = regmap_read(rt722->regmap, + RT722_BUF_ADDR_HID1 + offset + idx, &val); + if (ret < 0) + goto io_error; + buf[idx] = val & 0xff; + } + + if (buf[0] == 0x11) + btn_type = rt722_sdca_btn_type(&buf[1]); + } else + rt722->jack_type = 0; + + dev_dbg(&rt722->slave->dev, "%s, btn_type=0x%x\n", __func__, btn_type); + snd_soc_jack_report(rt722->hs_jack, rt722->jack_type | btn_type, + SND_JACK_HEADSET | + SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3); + + if (btn_type) { + /* button released */ + snd_soc_jack_report(rt722->hs_jack, rt722->jack_type, + SND_JACK_HEADSET | + SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3); + + mod_delayed_work(system_power_efficient_wq, + &rt722->jack_btn_check_work, msecs_to_jiffies(200)); + } + + return; + +io_error: + pr_err_ratelimited("IO error in %s, ret %d\n", __func__, ret); +} + +static void rt722_sdca_jack_init(struct rt722_sdca_priv *rt722) +{ + mutex_lock(&rt722->calibrate_mutex); + if (rt722->hs_jack) { + /* set SCP_SDCA_IntMask1[0]=1 */ + sdw_write_no_pm(rt722->slave, SDW_SCP_SDCA_INTMASK1, + SDW_SCP_SDCA_INTMASK_SDCA_0 | SDW_SCP_SDCA_INTMASK_SDCA_6); + /* set SCP_SDCA_IntMask2[0]=1 */ + sdw_write_no_pm(rt722->slave, SDW_SCP_SDCA_INTMASK2, + SDW_SCP_SDCA_INTMASK_SDCA_8); + dev_dbg(&rt722->slave->dev, "in %s enable\n", __func__); + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_HDA_LEGACY_UNSOL_CTL, 0x016E); + /* set XU(et03h) & XU(et0Dh) to Not bypassed */ + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_XU03, + RT722_SDCA_CTL_SELECTED_MODE, 0), 0); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_XU0D, + RT722_SDCA_CTL_SELECTED_MODE, 0), 0); + /* trigger GE interrupt */ + rt722_sdca_index_update_bits(rt722, RT722_VENDOR_HDA_CTL, + RT722_GE_RELATED_CTL2, 0x4000, 0x4000); + } + mutex_unlock(&rt722->calibrate_mutex); +} + +static int rt722_sdca_set_jack_detect(struct snd_soc_component *component, + struct snd_soc_jack *hs_jack, void *data) +{ + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + int ret; + + rt722->hs_jack = hs_jack; + + ret = pm_runtime_resume_and_get(component->dev); + if (ret < 0) { + if (ret != -EACCES) { + dev_err(component->dev, "%s: failed to resume %d\n", __func__, ret); + return ret; + } + /* pm_runtime not enabled yet */ + dev_dbg(component->dev, "%s: skipping jack init for now\n", __func__); + return 0; + } + + rt722_sdca_jack_init(rt722); + + pm_runtime_mark_last_busy(component->dev); + pm_runtime_put_autosuspend(component->dev); + + return 0; +} + +/* For SDCA control DAC/ADC Gain */ +static int rt722_sdca_set_gain_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned int read_l, read_r, gain_l_val, gain_r_val; + unsigned int adc_vol_flag = 0, changed = 0; + unsigned int lvalue, rvalue; + const unsigned int interval_offset = 0xc0; + const unsigned int tendB = 0xa00; + + if (strstr(ucontrol->id.name, "FU1E Capture Volume") || + strstr(ucontrol->id.name, "FU0F Capture Volume")) + adc_vol_flag = 1; + + regmap_read(rt722->mbq_regmap, mc->reg, &lvalue); + regmap_read(rt722->mbq_regmap, mc->rreg, &rvalue); + + /* L Channel */ + gain_l_val = ucontrol->value.integer.value[0]; + if (gain_l_val > mc->max) + gain_l_val = mc->max; + + if (mc->shift == 8) /* boost gain */ + gain_l_val = gain_l_val * tendB; + else { + /* ADC/DAC gain */ + if (adc_vol_flag) + gain_l_val = 0x1e00 - ((mc->max - gain_l_val) * interval_offset); + else + gain_l_val = 0 - ((mc->max - gain_l_val) * interval_offset); + gain_l_val &= 0xffff; + } + + /* R Channel */ + gain_r_val = ucontrol->value.integer.value[1]; + if (gain_r_val > mc->max) + gain_r_val = mc->max; + + if (mc->shift == 8) /* boost gain */ + gain_r_val = gain_r_val * tendB; + else { + /* ADC/DAC gain */ + if (adc_vol_flag) + gain_r_val = 0x1e00 - ((mc->max - gain_r_val) * interval_offset); + else + gain_r_val = 0 - ((mc->max - gain_r_val) * interval_offset); + gain_r_val &= 0xffff; + } + + if (lvalue != gain_l_val || rvalue != gain_r_val) + changed = 1; + else + return 0; + + /* Lch*/ + regmap_write(rt722->mbq_regmap, mc->reg, gain_l_val); + + /* Rch */ + regmap_write(rt722->mbq_regmap, mc->rreg, gain_r_val); + + regmap_read(rt722->mbq_regmap, mc->reg, &read_l); + regmap_read(rt722->mbq_regmap, mc->rreg, &read_r); + if (read_r == gain_r_val && read_l == gain_l_val) + return changed; + + return -EIO; +} + +static int rt722_sdca_set_gain_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + unsigned int read_l, read_r, ctl_l = 0, ctl_r = 0; + unsigned int adc_vol_flag = 0; + const unsigned int interval_offset = 0xc0; + const unsigned int tendB = 0xa00; + + if (strstr(ucontrol->id.name, "FU1E Capture Volume") || + strstr(ucontrol->id.name, "FU0F Capture Volume")) + adc_vol_flag = 1; + + regmap_read(rt722->mbq_regmap, mc->reg, &read_l); + regmap_read(rt722->mbq_regmap, mc->rreg, &read_r); + + if (mc->shift == 8) /* boost gain */ + ctl_l = read_l / tendB; + else { + if (adc_vol_flag) + ctl_l = mc->max - (((0x1e00 - read_l) & 0xffff) / interval_offset); + else + ctl_l = mc->max - (((0 - read_l) & 0xffff) / interval_offset); + } + + if (read_l != read_r) { + if (mc->shift == 8) /* boost gain */ + ctl_r = read_r / tendB; + else { /* ADC/DAC gain */ + if (adc_vol_flag) + ctl_r = mc->max - (((0x1e00 - read_r) & 0xffff) / interval_offset); + else + ctl_r = mc->max - (((0 - read_r) & 0xffff) / interval_offset); + } + } else { + ctl_r = ctl_l; + } + + ucontrol->value.integer.value[0] = ctl_l; + ucontrol->value.integer.value[1] = ctl_r; + + return 0; +} + +static int rt722_sdca_set_fu1e_capture_ctl(struct rt722_sdca_priv *rt722) +{ + int err, i; + unsigned int ch_mute; + + for (i = 0; i < ARRAY_SIZE(rt722->fu1e_mixer_mute); i++) { + ch_mute = rt722->fu1e_dapm_mute || rt722->fu1e_mixer_mute[i]; + err = regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, + RT722_SDCA_CTL_FU_MUTE, CH_01) + i, ch_mute); + if (err < 0) + return err; + } + + return 0; +} + +static int rt722_sdca_fu1e_capture_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct rt722_sdca_dmic_kctrl_priv *p = + (struct rt722_sdca_dmic_kctrl_priv *)kcontrol->private_value; + unsigned int i; + + for (i = 0; i < p->count; i++) + ucontrol->value.integer.value[i] = !rt722->fu1e_mixer_mute[i]; + + return 0; +} + +static int rt722_sdca_fu1e_capture_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct rt722_sdca_dmic_kctrl_priv *p = + (struct rt722_sdca_dmic_kctrl_priv *)kcontrol->private_value; + int err, changed = 0, i; + + for (i = 0; i < p->count; i++) { + if (rt722->fu1e_mixer_mute[i] != !ucontrol->value.integer.value[i]) + changed = 1; + rt722->fu1e_mixer_mute[i] = !ucontrol->value.integer.value[i]; + } + + err = rt722_sdca_set_fu1e_capture_ctl(rt722); + if (err < 0) + return err; + + return changed; +} + +static int rt722_sdca_set_fu0f_capture_ctl(struct rt722_sdca_priv *rt722) +{ + int err; + unsigned int ch_l, ch_r; + + ch_l = (rt722->fu0f_dapm_mute || rt722->fu0f_mixer_l_mute) ? 0x01 : 0x00; + ch_r = (rt722->fu0f_dapm_mute || rt722->fu0f_mixer_r_mute) ? 0x01 : 0x00; + + err = regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, + RT722_SDCA_CTL_FU_MUTE, CH_L), ch_l); + if (err < 0) + return err; + + err = regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, + RT722_SDCA_CTL_FU_MUTE, CH_R), ch_r); + if (err < 0) + return err; + + return 0; +} + +static int rt722_sdca_fu0f_capture_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + + ucontrol->value.integer.value[0] = !rt722->fu0f_mixer_l_mute; + ucontrol->value.integer.value[1] = !rt722->fu0f_mixer_r_mute; + return 0; +} + +static int rt722_sdca_fu0f_capture_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + int err, changed = 0; + + if (rt722->fu0f_mixer_l_mute != !ucontrol->value.integer.value[0] || + rt722->fu0f_mixer_r_mute != !ucontrol->value.integer.value[1]) + changed = 1; + + rt722->fu0f_mixer_l_mute = !ucontrol->value.integer.value[0]; + rt722->fu0f_mixer_r_mute = !ucontrol->value.integer.value[1]; + err = rt722_sdca_set_fu0f_capture_ctl(rt722); + if (err < 0) + return err; + + return changed; +} + +static int rt722_sdca_fu_info(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + struct rt722_sdca_dmic_kctrl_priv *p = + (struct rt722_sdca_dmic_kctrl_priv *)kcontrol->private_value; + + if (p->max == 1) + uinfo->type = SNDRV_CTL_ELEM_TYPE_BOOLEAN; + else + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = p->count; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = p->max; + return 0; +} + +static int rt722_sdca_dmic_set_gain_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct rt722_sdca_dmic_kctrl_priv *p = + (struct rt722_sdca_dmic_kctrl_priv *)kcontrol->private_value; + unsigned int boost_step = 0x0a00; + unsigned int vol_max = 0x1e00; + unsigned int regvalue, ctl, i; + unsigned int adc_vol_flag = 0; + const unsigned int interval_offset = 0xc0; + + if (strstr(ucontrol->id.name, "FU1E Capture Volume")) + adc_vol_flag = 1; + + /* check all channels */ + for (i = 0; i < p->count; i++) { + regmap_read(rt722->mbq_regmap, p->reg_base + i, &regvalue); + + if (!adc_vol_flag) /* boost gain */ + ctl = regvalue / boost_step; + else { /* ADC gain */ + if (adc_vol_flag) + ctl = p->max - (((vol_max - regvalue) & 0xffff) / interval_offset); + else + ctl = p->max - (((0 - regvalue) & 0xffff) / interval_offset); + } + + ucontrol->value.integer.value[i] = ctl; + } + + return 0; +} + +static int rt722_sdca_dmic_set_gain_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_dmic_kctrl_priv *p = + (struct rt722_sdca_dmic_kctrl_priv *)kcontrol->private_value; + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned int boost_step = 0x0a00; + unsigned int vol_max = 0x1e00; + unsigned int gain_val[4]; + unsigned int i, adc_vol_flag = 0, changed = 0; + unsigned int regvalue[4]; + const unsigned int interval_offset = 0xc0; + int err; + + if (strstr(ucontrol->id.name, "FU1E Capture Volume")) + adc_vol_flag = 1; + + /* check all channels */ + for (i = 0; i < p->count; i++) { + regmap_read(rt722->mbq_regmap, p->reg_base + i, &regvalue[i]); + + gain_val[i] = ucontrol->value.integer.value[i]; + if (gain_val[i] > p->max) + gain_val[i] = p->max; + + if (!adc_vol_flag) /* boost gain */ + gain_val[i] = gain_val[i] * boost_step; + else { /* ADC gain */ + gain_val[i] = vol_max - ((p->max - gain_val[i]) * interval_offset); + gain_val[i] &= 0xffff; + } + + if (regvalue[i] != gain_val[i]) + changed = 1; + } + + if (!changed) + return 0; + + for (i = 0; i < p->count; i++) { + err = regmap_write(rt722->mbq_regmap, p->reg_base + i, gain_val[i]); + if (err < 0) + dev_err(&rt722->slave->dev, "%#08x can't be set\n", p->reg_base + i); + } + + return changed; +} + +#define RT722_SDCA_PR_VALUE(xreg_base, xcount, xmax, xinvert) \ + ((unsigned long)&(struct rt722_sdca_dmic_kctrl_priv) \ + {.reg_base = xreg_base, .count = xcount, .max = xmax, \ + .invert = xinvert}) + +#define RT722_SDCA_FU_CTRL(xname, reg_base, xmax, xinvert, xcount) \ +{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname), \ + .info = rt722_sdca_fu_info, \ + .get = rt722_sdca_fu1e_capture_get, \ + .put = rt722_sdca_fu1e_capture_put, \ + .private_value = RT722_SDCA_PR_VALUE(reg_base, xcount, xmax, xinvert)} + +#define RT722_SDCA_EXT_TLV(xname, reg_base, xhandler_get,\ + xhandler_put, xcount, xmax, tlv_array) \ +{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname), \ + .access = SNDRV_CTL_ELEM_ACCESS_TLV_READ | \ + SNDRV_CTL_ELEM_ACCESS_READWRITE, \ + .tlv.p = (tlv_array), \ + .info = rt722_sdca_fu_info, \ + .get = xhandler_get, .put = xhandler_put, \ + .private_value = RT722_SDCA_PR_VALUE(reg_base, xcount, xmax, 0) } + +static const DECLARE_TLV_DB_SCALE(out_vol_tlv, -6525, 75, 0); +static const DECLARE_TLV_DB_SCALE(mic_vol_tlv, -1725, 75, 0); +static const DECLARE_TLV_DB_SCALE(boost_vol_tlv, 0, 1000, 0); + +static const struct snd_kcontrol_new rt722_sdca_controls[] = { + /* Headphone playback settings */ + SOC_DOUBLE_R_EXT_TLV("FU05 Playback Volume", + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_VOLUME, CH_L), + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_VOLUME, CH_R), 0, 0x57, 0, + rt722_sdca_set_gain_get, rt722_sdca_set_gain_put, out_vol_tlv), + /* Headset mic capture settings */ + SOC_DOUBLE_EXT("FU0F Capture Switch", SND_SOC_NOPM, 0, 1, 1, 0, + rt722_sdca_fu0f_capture_get, rt722_sdca_fu0f_capture_put), + SOC_DOUBLE_R_EXT_TLV("FU0F Capture Volume", + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, + RT722_SDCA_CTL_FU_VOLUME, CH_L), + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, + RT722_SDCA_CTL_FU_VOLUME, CH_R), 0, 0x3f, 0, + rt722_sdca_set_gain_get, rt722_sdca_set_gain_put, mic_vol_tlv), + SOC_DOUBLE_R_EXT_TLV("FU33 Boost Volume", + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, + RT722_SDCA_CTL_FU_CH_GAIN, CH_L), + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, + RT722_SDCA_CTL_FU_CH_GAIN, CH_R), 8, 3, 0, + rt722_sdca_set_gain_get, rt722_sdca_set_gain_put, boost_vol_tlv), + /* AMP playback settings */ + SOC_DOUBLE_R_EXT_TLV("FU06 Playback Volume", + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_VOLUME, CH_L), + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_VOLUME, CH_R), 0, 0x57, 0, + rt722_sdca_set_gain_get, rt722_sdca_set_gain_put, out_vol_tlv), + /* DMIC capture settings */ + RT722_SDCA_FU_CTRL("FU1E Capture Switch", + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, + RT722_SDCA_CTL_FU_MUTE, CH_01), 1, 1, 4), + RT722_SDCA_EXT_TLV("FU1E Capture Volume", + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, + RT722_SDCA_CTL_FU_VOLUME, CH_01), + rt722_sdca_dmic_set_gain_get, rt722_sdca_dmic_set_gain_put, + 4, 0x3f, mic_vol_tlv), + RT722_SDCA_EXT_TLV("FU15 Boost Volume", + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15, + RT722_SDCA_CTL_FU_CH_GAIN, CH_01), + rt722_sdca_dmic_set_gain_get, rt722_sdca_dmic_set_gain_put, + 4, 3, boost_vol_tlv), +}; + +static int rt722_sdca_adc_mux_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = + snd_soc_dapm_kcontrol_component(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned int val = 0, mask_sft; + + if (strstr(ucontrol->id.name, "ADC 22 Mux")) + mask_sft = 12; + else if (strstr(ucontrol->id.name, "ADC 24 Mux")) + mask_sft = 4; + else if (strstr(ucontrol->id.name, "ADC 25 Mux")) + mask_sft = 0; + else + return -EINVAL; + + rt722_sdca_index_read(rt722, RT722_VENDOR_HDA_CTL, + RT722_HDA_LEGACY_MUX_CTL0, &val); + + ucontrol->value.enumerated.item[0] = (val >> mask_sft) & 0x7; + + return 0; +} + +static int rt722_sdca_adc_mux_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = + snd_soc_dapm_kcontrol_component(kcontrol); + struct snd_soc_dapm_context *dapm = + snd_soc_dapm_kcontrol_dapm(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct soc_enum *e = (struct soc_enum *)kcontrol->private_value; + unsigned int *item = ucontrol->value.enumerated.item; + unsigned int val, val2 = 0, change, mask_sft; + + if (item[0] >= e->items) + return -EINVAL; + + if (strstr(ucontrol->id.name, "ADC 22 Mux")) + mask_sft = 12; + else if (strstr(ucontrol->id.name, "ADC 24 Mux")) + mask_sft = 4; + else if (strstr(ucontrol->id.name, "ADC 25 Mux")) + mask_sft = 0; + else + return -EINVAL; + + val = snd_soc_enum_item_to_val(e, item[0]) << e->shift_l; + + rt722_sdca_index_read(rt722, RT722_VENDOR_HDA_CTL, + RT722_HDA_LEGACY_MUX_CTL0, &val2); + val2 = (0x7 << mask_sft) & val2; + + if (val == val2) + change = 0; + else + change = 1; + + if (change) + rt722_sdca_index_update_bits(rt722, RT722_VENDOR_HDA_CTL, + RT722_HDA_LEGACY_MUX_CTL0, 0x7 << mask_sft, + val << mask_sft); + + snd_soc_dapm_mux_update_power(dapm, kcontrol, + item[0], e, NULL); + + return change; +} + +static const char * const adc22_mux_text[] = { + "MIC2", + "LINE1", + "LINE2", +}; + +static const char * const adc07_10_mux_text[] = { + "DMIC1", + "DMIC2", +}; + +static SOC_ENUM_SINGLE_DECL( + rt722_adc22_enum, SND_SOC_NOPM, 0, adc22_mux_text); + +static SOC_ENUM_SINGLE_DECL( + rt722_adc24_enum, SND_SOC_NOPM, 0, adc07_10_mux_text); + +static SOC_ENUM_SINGLE_DECL( + rt722_adc25_enum, SND_SOC_NOPM, 0, adc07_10_mux_text); + +static const struct snd_kcontrol_new rt722_sdca_adc22_mux = + SOC_DAPM_ENUM_EXT("ADC 22 Mux", rt722_adc22_enum, + rt722_sdca_adc_mux_get, rt722_sdca_adc_mux_put); + +static const struct snd_kcontrol_new rt722_sdca_adc24_mux = + SOC_DAPM_ENUM_EXT("ADC 24 Mux", rt722_adc24_enum, + rt722_sdca_adc_mux_get, rt722_sdca_adc_mux_put); + +static const struct snd_kcontrol_new rt722_sdca_adc25_mux = + SOC_DAPM_ENUM_EXT("ADC 25 Mux", rt722_adc25_enum, + rt722_sdca_adc_mux_get, rt722_sdca_adc_mux_put); + +static int rt722_sdca_fu42_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char unmute = 0x0, mute = 0x1; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_MUTE, CH_L), unmute); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_MUTE, CH_R), unmute); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_MUTE, CH_L), mute); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_MUTE, CH_R), mute); + break; + } + return 0; +} + +static int rt722_sdca_fu21_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char unmute = 0x0, mute = 0x1; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_MUTE, CH_L), unmute); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_MUTE, CH_R), unmute); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_MUTE, CH_L), mute); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_MUTE, CH_R), mute); + break; + } + return 0; +} + +static int rt722_sdca_fu113_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + rt722->fu1e_dapm_mute = false; + rt722_sdca_set_fu1e_capture_ctl(rt722); + break; + case SND_SOC_DAPM_PRE_PMD: + rt722->fu1e_dapm_mute = true; + rt722_sdca_set_fu1e_capture_ctl(rt722); + break; + } + return 0; +} + +static int rt722_sdca_fu36_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + rt722->fu0f_dapm_mute = false; + rt722_sdca_set_fu0f_capture_ctl(rt722); + break; + case SND_SOC_DAPM_PRE_PMD: + rt722->fu0f_dapm_mute = true; + rt722_sdca_set_fu0f_capture_ctl(rt722); + break; + } + return 0; +} + +static int rt722_sdca_pde47_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char ps0 = 0x0, ps3 = 0x3; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE40, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE40, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps3); + break; + } + return 0; +} + +static int rt722_sdca_pde23_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char ps0 = 0x0, ps3 = 0x3; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_PDE23, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_PDE23, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps3); + break; + } + return 0; +} + +static int rt722_sdca_pde11_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char ps0 = 0x0, ps3 = 0x3; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_PDE2A, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_PDE2A, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps3); + break; + } + return 0; +} + +static int rt722_sdca_pde12_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char ps0 = 0x0, ps3 = 0x3; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE12, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE12, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps3); + break; + } + return 0; +} + +static const struct snd_soc_dapm_widget rt722_sdca_dapm_widgets[] = { + SND_SOC_DAPM_OUTPUT("HP"), + SND_SOC_DAPM_OUTPUT("SPK"), + SND_SOC_DAPM_INPUT("MIC2"), + SND_SOC_DAPM_INPUT("LINE1"), + SND_SOC_DAPM_INPUT("LINE2"), + SND_SOC_DAPM_INPUT("DMIC1_2"), + SND_SOC_DAPM_INPUT("DMIC3_4"), + + SND_SOC_DAPM_SUPPLY("PDE 23", SND_SOC_NOPM, 0, 0, + rt722_sdca_pde23_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_SUPPLY("PDE 47", SND_SOC_NOPM, 0, 0, + rt722_sdca_pde47_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_SUPPLY("PDE 11", SND_SOC_NOPM, 0, 0, + rt722_sdca_pde11_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_SUPPLY("PDE 12", SND_SOC_NOPM, 0, 0, + rt722_sdca_pde12_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + + SND_SOC_DAPM_DAC_E("FU 21", NULL, SND_SOC_NOPM, 0, 0, + rt722_sdca_fu21_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_DAC_E("FU 42", NULL, SND_SOC_NOPM, 0, 0, + rt722_sdca_fu42_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_ADC_E("FU 36", NULL, SND_SOC_NOPM, 0, 0, + rt722_sdca_fu36_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_ADC_E("FU 113", NULL, SND_SOC_NOPM, 0, 0, + rt722_sdca_fu113_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_MUX("ADC 22 Mux", SND_SOC_NOPM, 0, 0, + &rt722_sdca_adc22_mux), + SND_SOC_DAPM_MUX("ADC 24 Mux", SND_SOC_NOPM, 0, 0, + &rt722_sdca_adc24_mux), + SND_SOC_DAPM_MUX("ADC 25 Mux", SND_SOC_NOPM, 0, 0, + &rt722_sdca_adc25_mux), + + SND_SOC_DAPM_AIF_IN("DP1RX", "DP1 Headphone Playback", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_OUT("DP2TX", "DP2 Headset Capture", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_IN("DP3RX", "DP3 Speaker Playback", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_OUT("DP6TX", "DP6 DMic Capture", 0, SND_SOC_NOPM, 0, 0), +}; + +static const struct snd_soc_dapm_route rt722_sdca_audio_map[] = { + {"FU 42", NULL, "DP1RX"}, + {"FU 21", NULL, "DP3RX"}, + + {"ADC 22 Mux", "MIC2", "MIC2"}, + {"ADC 22 Mux", "LINE1", "LINE1"}, + {"ADC 22 Mux", "LINE2", "LINE2"}, + {"ADC 24 Mux", "DMIC1", "DMIC1_2"}, + {"ADC 24 Mux", "DMIC2", "DMIC3_4"}, + {"ADC 25 Mux", "DMIC1", "DMIC1_2"}, + {"ADC 25 Mux", "DMIC2", "DMIC3_4"}, + {"FU 36", NULL, "PDE 12"}, + {"FU 36", NULL, "ADC 22 Mux"}, + {"FU 113", NULL, "PDE 11"}, + {"FU 113", NULL, "ADC 24 Mux"}, + {"FU 113", NULL, "ADC 25 Mux"}, + {"DP2TX", NULL, "FU 36"}, + {"DP6TX", NULL, "FU 113"}, + + {"HP", NULL, "PDE 47"}, + {"HP", NULL, "FU 42"}, + {"SPK", NULL, "PDE 23"}, + {"SPK", NULL, "FU 21"}, +}; + +static int rt722_sdca_parse_dt(struct rt722_sdca_priv *rt722, struct device *dev) +{ + device_property_read_u32(dev, "realtek,jd-src", &rt722->jd_src); + + return 0; +} + +static int rt722_sdca_probe(struct snd_soc_component *component) +{ + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + int ret; + + rt722_sdca_parse_dt(rt722, &rt722->slave->dev); + rt722->component = component; + + ret = pm_runtime_resume(component->dev); + if (ret < 0 && ret != -EACCES) + return ret; + + return 0; +} + +static const struct snd_soc_component_driver soc_sdca_dev_rt722 = { + .probe = rt722_sdca_probe, + .controls = rt722_sdca_controls, + .num_controls = ARRAY_SIZE(rt722_sdca_controls), + .dapm_widgets = rt722_sdca_dapm_widgets, + .num_dapm_widgets = ARRAY_SIZE(rt722_sdca_dapm_widgets), + .dapm_routes = rt722_sdca_audio_map, + .num_dapm_routes = ARRAY_SIZE(rt722_sdca_audio_map), + .set_jack = rt722_sdca_set_jack_detect, + .endianness = 1, +}; + +static int rt722_sdca_set_sdw_stream(struct snd_soc_dai *dai, void *sdw_stream, + int direction) +{ + snd_soc_dai_dma_data_set(dai, direction, sdw_stream); + + return 0; +} + +static void rt722_sdca_shutdown(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + snd_soc_dai_set_dma_data(dai, substream, NULL); +} + +static int rt722_sdca_pcm_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_component *component = dai->component; + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct sdw_stream_config stream_config; + struct sdw_port_config port_config; + enum sdw_data_direction direction; + struct sdw_stream_runtime *sdw_stream; + int retval, port, num_channels; + unsigned int sampling_rate; + + dev_dbg(dai->dev, "%s %s", __func__, dai->name); + sdw_stream = snd_soc_dai_get_dma_data(dai, substream); + + if (!sdw_stream) + return -EINVAL; + + if (!rt722->slave) + return -EINVAL; + + /* + * RT722_AIF1 with port = 1 for headphone playback + * RT722_AIF1 with port = 2 for headset-mic capture + * RT722_AIF2 with port = 3 for speaker playback + * RT722_AIF2 with port = 6 for digital-mic capture + */ + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) { + direction = SDW_DATA_DIR_RX; + if (dai->id == RT722_AIF1) + port = 1; + else if (dai->id == RT722_AIF2) + port = 3; + else + return -EINVAL; + } else { + direction = SDW_DATA_DIR_TX; + if (dai->id == RT722_AIF1) + port = 2; + else if (dai->id == RT722_AIF2) + port = 6; + else + return -EINVAL; + } + stream_config.frame_rate = params_rate(params); + stream_config.ch_count = params_channels(params); + stream_config.bps = snd_pcm_format_width(params_format(params)); + stream_config.direction = direction; + + num_channels = params_channels(params); + port_config.ch_mask = GENMASK(num_channels - 1, 0); + port_config.num = port; + + retval = sdw_stream_add_slave(rt722->slave, &stream_config, + &port_config, 1, sdw_stream); + if (retval) { + dev_err(dai->dev, "Unable to configure port\n"); + return retval; + } + + if (params_channels(params) > 16) { + dev_err(component->dev, "Unsupported channels %d\n", + params_channels(params)); + return -EINVAL; + } + + /* sampling rate configuration */ + switch (params_rate(params)) { + case 44100: + sampling_rate = RT722_SDCA_RATE_44100HZ; + break; + case 48000: + sampling_rate = RT722_SDCA_RATE_48000HZ; + break; + case 96000: + sampling_rate = RT722_SDCA_RATE_96000HZ; + break; + case 192000: + sampling_rate = RT722_SDCA_RATE_192000HZ; + break; + default: + dev_err(component->dev, "Rate %d is not supported\n", + params_rate(params)); + return -EINVAL; + } + + /* set sampling frequency */ + if (dai->id == RT722_AIF1) { + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_CS01, + RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), sampling_rate); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_CS11, + RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), sampling_rate); + } + + if (dai->id == RT722_AIF2) { + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_CS1F, + RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), sampling_rate); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_CS31, + RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), sampling_rate); + } + + return 0; +} + +static int rt722_sdca_pcm_hw_free(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct snd_soc_component *component = dai->component; + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct sdw_stream_runtime *sdw_stream = + snd_soc_dai_get_dma_data(dai, substream); + + if (!rt722->slave) + return -EINVAL; + + sdw_stream_remove_slave(rt722->slave, sdw_stream); + return 0; +} + +#define RT722_STEREO_RATES (SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000 | \ + SNDRV_PCM_RATE_96000 | SNDRV_PCM_RATE_192000) +#define RT722_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE | \ + SNDRV_PCM_FMTBIT_S24_LE) + +static const struct snd_soc_dai_ops rt722_sdca_ops = { + .hw_params = rt722_sdca_pcm_hw_params, + .hw_free = rt722_sdca_pcm_hw_free, + .set_stream = rt722_sdca_set_sdw_stream, + .shutdown = rt722_sdca_shutdown, +}; + +static struct snd_soc_dai_driver rt722_sdca_dai[] = { + { + .name = "rt722-sdca-aif1", + .id = RT722_AIF1, + .playback = { + .stream_name = "DP1 Headphone Playback", + .channels_min = 1, + .channels_max = 2, + .rates = RT722_STEREO_RATES, + .formats = RT722_FORMATS, + }, + .capture = { + .stream_name = "DP2 Headset Capture", + .channels_min = 1, + .channels_max = 2, + .rates = RT722_STEREO_RATES, + .formats = RT722_FORMATS, + }, + .ops = &rt722_sdca_ops, + }, + { + .name = "rt722-sdca-aif2", + .id = RT722_AIF2, + .playback = { + .stream_name = "DP3 Speaker Playback", + .channels_min = 1, + .channels_max = 2, + .rates = RT722_STEREO_RATES, + .formats = RT722_FORMATS, + }, + .capture = { + .stream_name = "DP6 DMic Capture", + .channels_min = 1, + .channels_max = 2, + .rates = RT722_STEREO_RATES, + .formats = RT722_FORMATS, + }, + .ops = &rt722_sdca_ops, + } +}; + +int rt722_sdca_init(struct device *dev, struct regmap *regmap, + struct regmap *mbq_regmap, struct sdw_slave *slave) +{ + struct rt722_sdca_priv *rt722; + + rt722 = devm_kzalloc(dev, sizeof(*rt722), GFP_KERNEL); + if (!rt722) + return -ENOMEM; + + dev_set_drvdata(dev, rt722); + rt722->slave = slave; + rt722->regmap = regmap; + rt722->mbq_regmap = mbq_regmap; + + mutex_init(&rt722->calibrate_mutex); + mutex_init(&rt722->disable_irq_lock); + + INIT_DELAYED_WORK(&rt722->jack_detect_work, rt722_sdca_jack_detect_handler); + INIT_DELAYED_WORK(&rt722->jack_btn_check_work, rt722_sdca_btn_check_handler); + + /* + * Mark hw_init to false + * HW init will be performed when device reports present + */ + rt722->hw_init = false; + rt722->first_hw_init = false; + rt722->fu1e_dapm_mute = true; + rt722->fu0f_dapm_mute = true; + rt722->fu0f_mixer_l_mute = rt722->fu0f_mixer_r_mute = true; + rt722->fu1e_mixer_mute[0] = rt722->fu1e_mixer_mute[1] = + rt722->fu1e_mixer_mute[2] = rt722->fu1e_mixer_mute[3] = true; + + return devm_snd_soc_register_component(dev, + &soc_sdca_dev_rt722, rt722_sdca_dai, ARRAY_SIZE(rt722_sdca_dai)); +} + +static void rt722_sdca_dmic_preset(struct rt722_sdca_priv *rt722) +{ + /* Set AD07 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_ADC0A_08_PDE_FLOAT_CTL, 0x2a29); + /* Set AD10 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_ADC10_PDE_FLOAT_CTL, 0x2a00); + /* Set DMIC1/DMIC2 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_DMIC1_2_PDE_FLOAT_CTL, 0x2a2a); + /* Set DMIC2 IT entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_DMIC_ENT_FLOAT_CTL, 0x2626); + /* Set AD10 FU entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_ADC_ENT_FLOAT_CTL, 0x1e00); + /* Set DMIC2 FU entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_DMIC_GAIN_ENT_FLOAT_CTL0, 0x1515); + /* Set AD10 FU channel floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_ADC_VOL_CH_FLOAT_CTL, 0x0304); + /* Set DMIC2 FU channel floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_DMIC_GAIN_ENT_FLOAT_CTL2, 0x0304); + /* vf71f_r12_07_06 and vf71f_r13_07_06 = 2’b00 */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_HDA_LEGACY_CONFIG_CTL0, 0x0000); + /* Enable vf707_r12_05/vf707_r13_05 */ + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_IT26, + RT722_SDCA_CTL_VENDOR_DEF, 0), 0x01); + /* Fine tune PDE2A latency */ + regmap_write(rt722->regmap, 0x2f5c, 0x25); +} + +static void rt722_sdca_amp_preset(struct rt722_sdca_priv *rt722) +{ + /* Set DVQ=01 */ + rt722_sdca_index_write(rt722, RT722_VENDOR_REG, RT722_CLSD_CTRL6, + 0xc215); + /* Reset dc_cal_top */ + rt722_sdca_index_write(rt722, RT722_VENDOR_CALI, RT722_DC_CALIB_CTRL, + 0x702c); + /* W1C Trigger Calibration */ + rt722_sdca_index_write(rt722, RT722_VENDOR_CALI, RT722_DC_CALIB_CTRL, + 0xf02d); + /* Set DAC02/ClassD power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_AMP_PDE_FLOAT_CTL, + 0x2323); + /* Set EAPD high */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_EAPD_CTL, + 0x0002); + /* Enable vf707_r14 */ + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_OT23, + RT722_SDCA_CTL_VENDOR_DEF, CH_08), 0x04); +} + +static void rt722_sdca_jack_preset(struct rt722_sdca_priv *rt722) +{ + int loop_check, chk_cnt = 100, ret; + unsigned int calib_status = 0; + + /* Read eFuse */ + rt722_sdca_index_write(rt722, RT722_VENDOR_SPK_EFUSE, RT722_DC_CALIB_CTRL, + 0x4808); + /* Button A, B, C, D bypass mode */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_UMP_HID_CTL4, + 0xcf00); + /* HID1 slot enable */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_UMP_HID_CTL5, + 0x000f); + /* Report ID for HID1 */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_UMP_HID_CTL0, + 0x1100); + /* OSC/OOC for slot 2, 3 */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_UMP_HID_CTL7, + 0x0c12); + /* Set JD de-bounce clock control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_REG, RT722_JD_CTRL1, + 0x7002); + /* Set DVQ=01 */ + rt722_sdca_index_write(rt722, RT722_VENDOR_REG, RT722_CLSD_CTRL6, + 0xc215); + /* FSM switch to calibration manual mode */ + rt722_sdca_index_write(rt722, RT722_VENDOR_REG, RT722_FSM_CTL, + 0x4100); + /* W1C Trigger DC calibration (HP) */ + rt722_sdca_index_write(rt722, RT722_VENDOR_CALI, RT722_DAC_DC_CALI_CTL3, + 0x008d); + /* check HP calibration FSM status */ + for (loop_check = 0; loop_check < chk_cnt; loop_check++) { + ret = rt722_sdca_index_read(rt722, RT722_VENDOR_CALI, + RT722_DAC_DC_CALI_CTL3, &calib_status); + if (ret < 0 || loop_check == chk_cnt) + dev_dbg(&rt722->slave->dev, "calibration failed!, ret=%d\n", ret); + if ((calib_status & 0x0040) == 0x0) + break; + } + /* Release HP-JD, EN_CBJ_TIE_GL/R open, en_osw gating auto done bit */ + rt722_sdca_index_write(rt722, RT722_VENDOR_REG, RT722_DIGITAL_MISC_CTRL4, + 0x0010); + /* Set ADC09 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_ADC0A_08_PDE_FLOAT_CTL, + 0x2a12); + /* Set MIC2 and LINE1 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_MIC2_LINE2_PDE_FLOAT_CTL, + 0x3429); + /* Set ET41h and LINE2 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_ET41_LINE2_PDE_FLOAT_CTL, + 0x4112); + /* Set DAC03 and HP power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_DAC03_HP_PDE_FLOAT_CTL, + 0x4040); + /* Fine tune PDE40 latency */ + regmap_write(rt722->regmap, 0x2f58, 0x07); +} + +int rt722_sdca_io_init(struct device *dev, struct sdw_slave *slave) +{ + struct rt722_sdca_priv *rt722 = dev_get_drvdata(dev); + + rt722->disable_irq = false; + + if (rt722->hw_init) + return 0; + + if (rt722->first_hw_init) { + regcache_cache_only(rt722->regmap, false); + regcache_cache_bypass(rt722->regmap, true); + regcache_cache_only(rt722->mbq_regmap, false); + regcache_cache_bypass(rt722->mbq_regmap, true); + } else { + /* + * PM runtime is only enabled when a Slave reports as Attached + */ + + /* set autosuspend parameters */ + pm_runtime_set_autosuspend_delay(&slave->dev, 3000); + pm_runtime_use_autosuspend(&slave->dev); + + /* update count of parent 'active' children */ + pm_runtime_set_active(&slave->dev); + + /* make sure the device does not suspend immediately */ + pm_runtime_mark_last_busy(&slave->dev); + + pm_runtime_enable(&slave->dev); + } + + pm_runtime_get_noresume(&slave->dev); + + rt722_sdca_dmic_preset(rt722); + rt722_sdca_amp_preset(rt722); + rt722_sdca_jack_preset(rt722); + + if (rt722->first_hw_init) { + regcache_cache_bypass(rt722->regmap, false); + regcache_mark_dirty(rt722->regmap); + regcache_cache_bypass(rt722->mbq_regmap, false); + regcache_mark_dirty(rt722->mbq_regmap); + } else + rt722->first_hw_init = true; + + /* Mark Slave initialization complete */ + rt722->hw_init = true; + + pm_runtime_mark_last_busy(&slave->dev); + pm_runtime_put_autosuspend(&slave->dev); + + dev_dbg(&slave->dev, "%s hw_init complete\n", __func__); + return 0; +} + +MODULE_DESCRIPTION("ASoC RT722 SDCA SDW driver"); +MODULE_AUTHOR("Jack Yu <jack.yu(a)realtek.com>"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/rt722-sdca.h b/sound/soc/codecs/rt722-sdca.h new file mode 100644 index 000000000000..b80b901a0636 --- /dev/null +++ b/sound/soc/codecs/rt722-sdca.h @@ -0,0 +1,237 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * rt722-sdca.h -- RT722 SDCA ALSA SoC audio driver header + * + * Copyright(c) 2023 Realtek Semiconductor Corp. + */ + +#ifndef __RT722_H__ +#define __RT722_H__ + +#include <linux/pm.h> +#include <linux/regmap.h> +#include <linux/soundwire/sdw.h> +#include <linux/soundwire/sdw_type.h> +#include <sound/soc.h> +#include <linux/workqueue.h> + +struct rt722_sdca_priv { + struct regmap *regmap; + struct regmap *mbq_regmap; + struct snd_soc_component *component; + struct sdw_slave *slave; + enum sdw_slave_status status; + struct sdw_bus_params params; + bool hw_init; + bool first_hw_init; + struct mutex calibrate_mutex; + struct mutex disable_irq_lock; + bool disable_irq; + /* For Headset jack & Headphone */ + unsigned int scp_sdca_stat1; + unsigned int scp_sdca_stat2; + struct snd_soc_jack *hs_jack; + struct delayed_work jack_detect_work; + struct delayed_work jack_btn_check_work; + int jack_type; + int jd_src; + bool fu0f_dapm_mute; + bool fu0f_mixer_l_mute; + bool fu0f_mixer_r_mute; + /* For DMIC */ + bool fu1e_dapm_mute; + bool fu1e_mixer_mute[4]; +}; + +struct rt722_sdca_dmic_kctrl_priv { + unsigned int reg_base; + unsigned int count; + unsigned int max; + unsigned int invert; +}; + +/* NID */ +#define RT722_VENDOR_REG 0x20 +#define RT722_VENDOR_CALI 0x58 +#define RT722_VENDOR_SPK_EFUSE 0x5c +#define RT722_VENDOR_IMS_DRE 0x5b +#define RT722_VENDOR_ANALOG_CTL 0x5f +#define RT722_VENDOR_HDA_CTL 0x61 + +/* Index (NID:20h) */ +#define RT722_JD_PRODUCT_NUM 0x00 +#define RT722_ANALOG_BIAS_CTL3 0x04 +#define RT722_JD_CTRL1 0x09 +#define RT722_LDO2_3_CTL1 0x0e +#define RT722_LDO1_CTL 0x1a +#define RT722_HP_JD_CTRL 0x24 +#define RT722_CLSD_CTRL6 0x3c +#define RT722_COMBO_JACK_AUTO_CTL1 0x45 +#define RT722_COMBO_JACK_AUTO_CTL2 0x46 +#define RT722_COMBO_JACK_AUTO_CTL3 0x47 +#define RT722_DIGITAL_MISC_CTRL4 0x4a +#define RT722_FSM_CTL 0x67 +#define RT722_SDCA_INTR_REC 0x82 +#define RT722_SW_CONFIG1 0x8a +#define RT722_SW_CONFIG2 0x8b + +/* Index (NID:58h) */ +#define RT722_DAC_DC_CALI_CTL0 0x00 +#define RT722_DAC_DC_CALI_CTL1 0x01 +#define RT722_DAC_DC_CALI_CTL2 0x02 +#define RT722_DAC_DC_CALI_CTL3 0x03 + +/* Index (NID:59h) */ +#define RT722_ULTRA_SOUND_DETECTOR6 0x1e + +/* Index (NID:5bh) */ +#define RT722_IMS_DIGITAL_CTL1 0x00 +#define RT722_IMS_DIGITAL_CTL5 0x05 +#define RT722_HP_DETECT_RLDET_CTL1 0x29 +#define RT722_HP_DETECT_RLDET_CTL2 0x2a + +/* Index (NID:5fh) */ +#define RT722_MISC_POWER_CTL0 0x00 +#define RT722_MISC_POWER_CTL7 0x08 + +/* Index (NID:61h) */ +#define RT722_HDA_LEGACY_MUX_CTL0 0x00 +#define RT722_HDA_LEGACY_UNSOL_CTL 0x03 +#define RT722_HDA_LEGACY_CONFIG_CTL0 0x06 +#define RT722_HDA_LEGACY_RESET_CTL 0x08 +#define RT722_HDA_LEGACY_GPIO_WAKE_EN_CTL 0x0e +#define RT722_DMIC_ENT_FLOAT_CTL 0x10 +#define RT722_DMIC_GAIN_ENT_FLOAT_CTL0 0x11 +#define RT722_DMIC_GAIN_ENT_FLOAT_CTL2 0x13 +#define RT722_ADC_ENT_FLOAT_CTL 0x15 +#define RT722_ADC_VOL_CH_FLOAT_CTL 0x17 +#define RT722_ADC_SAMPLE_RATE_FLOAT 0x18 +#define RT722_DAC03_HP_PDE_FLOAT_CTL 0x22 +#define RT722_MIC2_LINE2_PDE_FLOAT_CTL 0x23 +#define RT722_ET41_LINE2_PDE_FLOAT_CTL 0x24 +#define RT722_ADC0A_08_PDE_FLOAT_CTL 0x25 +#define RT722_ADC10_PDE_FLOAT_CTL 0x26 +#define RT722_DMIC1_2_PDE_FLOAT_CTL 0x28 +#define RT722_AMP_PDE_FLOAT_CTL 0x29 +#define RT722_I2S_IN_OUT_PDE_FLOAT_CTL 0x2f +#define RT722_GE_RELATED_CTL1 0x45 +#define RT722_GE_RELATED_CTL2 0x46 +#define RT722_MIXER_CTL0 0x52 +#define RT722_MIXER_CTL1 0x53 +#define RT722_EAPD_CTL 0x55 +#define RT722_UMP_HID_CTL0 0x60 +#define RT722_UMP_HID_CTL1 0x61 +#define RT722_UMP_HID_CTL2 0x62 +#define RT722_UMP_HID_CTL3 0x63 +#define RT722_UMP_HID_CTL4 0x64 +#define RT722_UMP_HID_CTL5 0x65 +#define RT722_UMP_HID_CTL6 0x66 +#define RT722_UMP_HID_CTL7 0x67 +#define RT722_UMP_HID_CTL8 0x68 + +/* Parameter & Verb control 01 (0x1a)(NID:20h) */ +#define RT722_HIDDEN_REG_SW_RESET (0x1 << 14) + +/* combo jack auto switch control 2 (0x46)(NID:20h) */ +#define RT722_COMBOJACK_AUTO_DET_STATUS (0x1 << 11) +#define RT722_COMBOJACK_AUTO_DET_TRS (0x1 << 10) +#define RT722_COMBOJACK_AUTO_DET_CTIA (0x1 << 9) +#define RT722_COMBOJACK_AUTO_DET_OMTP (0x1 << 8) + +/* DAC calibration control (0x00)(NID:58h) */ +#define RT722_DC_CALIB_CTRL (0x1 << 16) +/* DAC DC offset calibration control-1 (0x01)(NID:58h) */ +#define RT722_PDM_DC_CALIB_STATUS (0x1 << 15) + +#define RT722_EAPD_HIGH 0x2 +#define RT722_EAPD_LOW 0x0 + +/* Buffer address for HID */ +#define RT722_BUF_ADDR_HID1 0x44030000 +#define RT722_BUF_ADDR_HID2 0x44030020 + +/* RT722 SDCA Control - function number */ +#define FUNC_NUM_JACK_CODEC 0x01 +#define FUNC_NUM_MIC_ARRAY 0x02 +#define FUNC_NUM_HID 0x03 +#define FUNC_NUM_AMP 0x04 + +/* RT722 SDCA entity */ +#define RT722_SDCA_ENT_HID01 0x01 +#define RT722_SDCA_ENT_GE49 0x49 +#define RT722_SDCA_ENT_USER_FU05 0x05 +#define RT722_SDCA_ENT_USER_FU06 0x06 +#define RT722_SDCA_ENT_USER_FU0F 0x0f +#define RT722_SDCA_ENT_USER_FU10 0x19 +#define RT722_SDCA_ENT_USER_FU1E 0x1e +#define RT722_SDCA_ENT_FU15 0x15 +#define RT722_SDCA_ENT_PDE23 0x23 +#define RT722_SDCA_ENT_PDE40 0x40 +#define RT722_SDCA_ENT_PDE11 0x11 +#define RT722_SDCA_ENT_PDE12 0x12 +#define RT722_SDCA_ENT_PDE2A 0x2a +#define RT722_SDCA_ENT_CS01 0x01 +#define RT722_SDCA_ENT_CS11 0x11 +#define RT722_SDCA_ENT_CS1F 0x1f +#define RT722_SDCA_ENT_CS1C 0x1c +#define RT722_SDCA_ENT_CS31 0x31 +#define RT722_SDCA_ENT_OT23 0x42 +#define RT722_SDCA_ENT_IT26 0x26 +#define RT722_SDCA_ENT_IT09 0x09 +#define RT722_SDCA_ENT_PLATFORM_FU15 0x15 +#define RT722_SDCA_ENT_PLATFORM_FU44 0x44 +#define RT722_SDCA_ENT_XU03 0x03 +#define RT722_SDCA_ENT_XU0D 0x0d + +/* RT722 SDCA control */ +#define RT722_SDCA_CTL_SAMPLE_FREQ_INDEX 0x10 +#define RT722_SDCA_CTL_FU_MUTE 0x01 +#define RT722_SDCA_CTL_FU_VOLUME 0x02 +#define RT722_SDCA_CTL_HIDTX_CURRENT_OWNER 0x10 +#define RT722_SDCA_CTL_HIDTX_SET_OWNER_TO_DEVICE 0x11 +#define RT722_SDCA_CTL_HIDTX_MESSAGE_OFFSET 0x12 +#define RT722_SDCA_CTL_HIDTX_MESSAGE_LENGTH 0x13 +#define RT722_SDCA_CTL_SELECTED_MODE 0x01 +#define RT722_SDCA_CTL_DETECTED_MODE 0x02 +#define RT722_SDCA_CTL_REQ_POWER_STATE 0x01 +#define RT722_SDCA_CTL_VENDOR_DEF 0x30 +#define RT722_SDCA_CTL_FU_CH_GAIN 0x0b + +/* RT722 SDCA channel */ +#define CH_L 0x01 +#define CH_R 0x02 +#define CH_01 0x01 +#define CH_02 0x02 +#define CH_03 0x03 +#define CH_04 0x04 +#define CH_08 0x08 + +/* sample frequency index */ +#define RT722_SDCA_RATE_16000HZ 0x04 +#define RT722_SDCA_RATE_32000HZ 0x07 +#define RT722_SDCA_RATE_44100HZ 0x08 +#define RT722_SDCA_RATE_48000HZ 0x09 +#define RT722_SDCA_RATE_96000HZ 0x0b +#define RT722_SDCA_RATE_192000HZ 0x0d + +enum { + RT722_AIF1, /* For headset mic and headphone */ + RT722_AIF2, /* For speaker and dmic */ + RT722_AIFS, +}; + +enum rt722_sdca_jd_src { + RT722_JD_NULL, + RT722_JD1, +}; + +int rt722_sdca_io_init(struct device *dev, struct sdw_slave *slave); +int rt722_sdca_init(struct device *dev, struct regmap *regmap, + struct regmap *mbq_regmap, struct sdw_slave *slave); +int rt722_sdca_index_write(struct rt722_sdca_priv *rt722, + unsigned int nid, unsigned int reg, unsigned int value); +int rt722_sdca_index_read(struct rt722_sdca_priv *rt722, + unsigned int nid, unsigned int reg, unsigned int *value); + +int rt722_sdca_jack_detect(struct rt722_sdca_priv *rt722, bool *hp, bool *mic); +#endif /* __RT722_H__ */ -- 2.40.0

2 2

[PATCH 0/7] ASoC: mediatek: mt8188: revise AFE driver
by Trevor Wu 20 Apr '23

20 Apr '23

The series of patches consists of three major changes. First, remove redundant supply for ADDA DAI dirver. Second, revise ETDM control including APLL dynamic switch via DAPM, so APLL can be enabled when it is really required. Finally, AFE probe function is updated. Bus protection change was dropped at the previous patch because the dependent change was not accepted. Trevor Wu (7): ASoC: mediatek: mt8188: remove supply AUDIO_HIRES ASoC: mediatek: mt8188: complete set_tdm_slot function ASoC: mediatek: mt8188: revise ETDM control flow ASoC: mediatek: mt8188: refine APLL control ASoC: mediatek: mt8188: combine afe component registration ASoC: mediatek: mt8188: add bus protection ASoC: dt-bindings: mediatek,mt8188-afe: add audio properties .../bindings/sound/mediatek,mt8188-afe.yaml | 18 + sound/soc/mediatek/mt8188/mt8188-afe-clk.c | 138 ++- sound/soc/mediatek/mt8188/mt8188-afe-clk.h | 11 + sound/soc/mediatek/mt8188/mt8188-afe-pcm.c | 113 ++- sound/soc/mediatek/mt8188/mt8188-dai-adda.c | 37 - sound/soc/mediatek/mt8188/mt8188-dai-etdm.c | 922 ++++++++++-------- sound/soc/mediatek/mt8188/mt8188-reg.h | 2 + 7 files changed, 759 insertions(+), 482 deletions(-) -- 2.18.0

4 18

[GIT PULL] ASoC fixes for v6.3-rc7
by Mark Brown 20 Apr '23

20 Apr '23

The following changes since commit e3720f92e0237921da537e47a0b24e27899203f8: ASoC: SOF: avoid a NULL dereference with unsupported widgets (2023-03-29 14:40:18 +0100) are available in the Git repository at: https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git tags/asoc-fix-v6.3-rc7 for you to fetch changes up to 86a24e99c97234f87d9f70b528a691150e145197: ASoC: fsl_asrc_dma: fix potential null-ptr-deref (2023-04-19 13:42:56 +0100) ---------------------------------------------------------------- ASoC: Fixes for v6.3 A few remaining small fixes for v6.3, all small driver specific ones. ---------------------------------------------------------------- Chancel Liu (1): ASoC: fsl_sai: Fix pins setting for i.MX8QM platform Daniel Baluta (1): ASoC: SOF: pm: Tear down pipelines only if DSP was active Long Wang (1): ASoC: max98373: change power down sequence for smart amp Nikita Zhandarovich (1): ASoC: fsl_asrc_dma: fix potential null-ptr-deref Peter Ujfalusi (1): ASoC: SOF: ipc4-topology: Clarify bind failure caused by missing fw_module sound/soc/codecs/max98373.c | 4 ++-- sound/soc/fsl/fsl_asrc_dma.c | 11 ++++++++--- sound/soc/fsl/fsl_sai.c | 2 +- sound/soc/sof/ipc4-topology.c | 10 ++++++---- sound/soc/sof/pm.c | 8 +++++++- 5 files changed, 24 insertions(+), 11 deletions(-)

2 1

[PATCH] ALSA: hda/realtek: fix mute/micmute LEDs for a HP ProBook
by Andy Chi 20 Apr '23

20 Apr '23

There is a HP ProBook 455 G10 which using ALC236 codec and need the ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF quirk to make mute LED and micmute LED work. Signed-off-by: Andy Chi <andy.chi(a)canonical.com> --- sound/pci/hda/patch_realtek.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 6a6c72b5ea26..f70d6a33421d 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -9468,6 +9468,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x103c, 0x8b47, "HP", ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED), SND_PCI_QUIRK(0x103c, 0x8b5d, "HP", ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF), SND_PCI_QUIRK(0x103c, 0x8b5e, "HP", ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF), + SND_PCI_QUIRK(0x103c, 0x8b65, "HP ProBook 455 15.6 inch G10 Notebook PC", ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF), SND_PCI_QUIRK(0x103c, 0x8b66, "HP", ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF), SND_PCI_QUIRK(0x103c, 0x8b7a, "HP", ALC236_FIXUP_HP_GPIO_LED), SND_PCI_QUIRK(0x103c, 0x8b7d, "HP", ALC236_FIXUP_HP_GPIO_LED), -- 2.34.1

2 1

[PATCH] Revert "ASoC: fsl: remove unnecessary dai_link->platform"
by Shengjiu Wang 20 Apr '23

20 Apr '23

This reverts commit 33683cbf49b5412061cb1e4c876063fdef86def4. dai_link->platform is needed. The platform component is "snd_dmaengine_pcm", which is registered from cpu driver, If dai_link->platform is not assigned, then platform component will not be probed, then there will be issue: aplay: main:831: audio open error: Invalid argument Signed-off-by: Shengjiu Wang <shengjiu.wang(a)nxp.com> --- sound/soc/fsl/imx-audmix.c | 14 ++++++++++---- sound/soc/fsl/imx-spdif.c | 5 ++++- 2 files changed, 14 insertions(+), 5 deletions(-) diff --git a/sound/soc/fsl/imx-audmix.c b/sound/soc/fsl/imx-audmix.c index 2c57fe9d2d08..1292a845c424 100644 --- a/sound/soc/fsl/imx-audmix.c +++ b/sound/soc/fsl/imx-audmix.c @@ -207,8 +207,8 @@ static int imx_audmix_probe(struct platform_device *pdev) for (i = 0; i < num_dai; i++) { struct snd_soc_dai_link_component *dlc; - /* for CPU/Codec x 2 */ - dlc = devm_kcalloc(&pdev->dev, 4, sizeof(*dlc), GFP_KERNEL); + /* for CPU/Codec/Platform x 2 */ + dlc = devm_kcalloc(&pdev->dev, 6, sizeof(*dlc), GFP_KERNEL); if (!dlc) return -ENOMEM; @@ -240,9 +240,11 @@ static int imx_audmix_probe(struct platform_device *pdev) priv->dai[i].cpus = &dlc[0]; priv->dai[i].codecs = &dlc[1]; + priv->dai[i].platforms = &dlc[2]; priv->dai[i].num_cpus = 1; priv->dai[i].num_codecs = 1; + priv->dai[i].num_platforms = 1; priv->dai[i].name = dai_name; priv->dai[i].stream_name = "HiFi-AUDMIX-FE"; @@ -250,6 +252,7 @@ static int imx_audmix_probe(struct platform_device *pdev) priv->dai[i].codecs->name = "snd-soc-dummy"; priv->dai[i].cpus->of_node = args.np; priv->dai[i].cpus->dai_name = dev_name(&cpu_pdev->dev); + priv->dai[i].platforms->of_node = args.np; priv->dai[i].dynamic = 1; priv->dai[i].dpcm_playback = 1; priv->dai[i].dpcm_capture = (i == 0 ? 1 : 0); @@ -264,17 +267,20 @@ static int imx_audmix_probe(struct platform_device *pdev) be_cp = devm_kasprintf(&pdev->dev, GFP_KERNEL, "AUDMIX-Capture-%d", i); - priv->dai[num_dai + i].cpus = &dlc[2]; - priv->dai[num_dai + i].codecs = &dlc[3]; + priv->dai[num_dai + i].cpus = &dlc[3]; + priv->dai[num_dai + i].codecs = &dlc[4]; + priv->dai[num_dai + i].platforms = &dlc[5]; priv->dai[num_dai + i].num_cpus = 1; priv->dai[num_dai + i].num_codecs = 1; + priv->dai[num_dai + i].num_platforms = 1; priv->dai[num_dai + i].name = be_name; priv->dai[num_dai + i].codecs->dai_name = "snd-soc-dummy-dai"; priv->dai[num_dai + i].codecs->name = "snd-soc-dummy"; priv->dai[num_dai + i].cpus->of_node = audmix_np; priv->dai[num_dai + i].cpus->dai_name = be_name; + priv->dai[num_dai + i].platforms->name = "snd-soc-dummy"; priv->dai[num_dai + i].no_pcm = 1; priv->dai[num_dai + i].dpcm_playback = 1; priv->dai[num_dai + i].dpcm_capture = 1; diff --git a/sound/soc/fsl/imx-spdif.c b/sound/soc/fsl/imx-spdif.c index 114b49660193..4446fba755b9 100644 --- a/sound/soc/fsl/imx-spdif.c +++ b/sound/soc/fsl/imx-spdif.c @@ -26,7 +26,7 @@ static int imx_spdif_audio_probe(struct platform_device *pdev) } data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); - comp = devm_kzalloc(&pdev->dev, 2 * sizeof(*comp), GFP_KERNEL); + comp = devm_kzalloc(&pdev->dev, 3 * sizeof(*comp), GFP_KERNEL); if (!data || !comp) { ret = -ENOMEM; goto end; @@ -34,15 +34,18 @@ static int imx_spdif_audio_probe(struct platform_device *pdev) data->dai.cpus = &comp[0]; data->dai.codecs = &comp[1]; + data->dai.platforms = &comp[2]; data->dai.num_cpus = 1; data->dai.num_codecs = 1; + data->dai.num_platforms = 1; data->dai.name = "S/PDIF PCM"; data->dai.stream_name = "S/PDIF PCM"; data->dai.codecs->dai_name = "snd-soc-dummy-dai"; data->dai.codecs->name = "snd-soc-dummy"; data->dai.cpus->of_node = spdif_np; + data->dai.platforms->of_node = spdif_np; data->dai.playback_only = true; data->dai.capture_only = true; -- 2.34.1

3 3

[PATCH] ASoC: nau8825: fix delay time range check
by Arnd Bergmann 19 Apr '23

19 Apr '23

From: Arnd Bergmann <arnd(a)arndb.de> clang points out that the recently added range check is nonsensical: sound/soc/codecs/nau8825.c:2826:31: error: overlapping comparisons always evaluate to false [-Werror,-Wtautological-overlap-compare] if (nau8825->adc_delay < 125 && nau8825->adc_delay > 500) ~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~ The DT binding document confirms that the intention is to warn if it's outside of the 125..500 range, so do that instead. Fixes: fc0b096c9291 ("ASoC: nau8825: Add delay control for input path") Signed-off-by: Arnd Bergmann <arnd(a)arndb.de> --- sound/soc/codecs/nau8825.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/codecs/nau8825.c b/sound/soc/codecs/nau8825.c index c4389f5fe603..f4eb999761a4 100644 --- a/sound/soc/codecs/nau8825.c +++ b/sound/soc/codecs/nau8825.c @@ -2823,7 +2823,7 @@ static int nau8825_read_device_properties(struct device *dev, ret = device_property_read_u32(dev, "nuvoton,adc-delay-ms", &nau8825->adc_delay); if (ret) nau8825->adc_delay = 125; - if (nau8825->adc_delay < 125 && nau8825->adc_delay > 500) + if (nau8825->adc_delay < 125 || nau8825->adc_delay > 500) dev_warn(dev, "Please set the suitable delay time!\n"); nau8825->mclk = devm_clk_get(dev, "mclk"); -- 2.39.2

3 2

[PATCH] ASoC: fsl: Simplify an error message
by Christophe JAILLET 19 Apr '23

19 Apr '23

dev_err_probe() already display the error code. There is no need to duplicate it explicitly in the error message. Signed-off-by: Christophe JAILLET <christophe.jaillet(a)wanadoo.fr> --- sound/soc/fsl/fsl-asoc-card.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/fsl/fsl-asoc-card.c b/sound/soc/fsl/fsl-asoc-card.c index bffa1048d31e..40870668ee24 100644 --- a/sound/soc/fsl/fsl-asoc-card.c +++ b/sound/soc/fsl/fsl-asoc-card.c @@ -858,7 +858,7 @@ static int fsl_asoc_card_probe(struct platform_device *pdev) ret = devm_snd_soc_register_card(&pdev->dev, &priv->card); if (ret) { - dev_err_probe(&pdev->dev, ret, "snd_soc_register_card failed: %d\n", ret); + dev_err_probe(&pdev->dev, ret, "snd_soc_register_card failed\n"); goto asrc_fail; } -- 2.34.1

4 3

[PATCH] ASoC: fsl_asrc_dma: fix potential null-ptr-deref
by Nikita Zhandarovich 19 Apr '23

19 Apr '23

dma_request_slave_channel() may return NULL which will lead to NULL pointer dereference error in 'tmp_chan->private'. Correct this behaviour by, first, switching from deprecated function dma_request_slave_channel() to dma_request_chan(). Secondly, enable sanity check for the resuling value of dma_request_chan(). Also, fix description that follows the enacted changes and that concerns the use of dma_request_slave_channel(). Fixes: 706e2c881158 ("ASoC: fsl_asrc_dma: Reuse the dma channel if available in Back-End") Co-developed-by: Natalia Petrova <n.petrova(a)fintech.ru> Signed-off-by: Nikita Zhandarovich <n.zhandarovich(a)fintech.ru> --- sound/soc/fsl/fsl_asrc_dma.c | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-) diff --git a/sound/soc/fsl/fsl_asrc_dma.c b/sound/soc/fsl/fsl_asrc_dma.c index 3b81a465814a..05a7d1588d20 100644 --- a/sound/soc/fsl/fsl_asrc_dma.c +++ b/sound/soc/fsl/fsl_asrc_dma.c @@ -209,14 +209,19 @@ static int fsl_asrc_dma_hw_params(struct snd_soc_component *component, be_chan = soc_component_to_pcm(component_be)->chan[substream->stream]; tmp_chan = be_chan; } - if (!tmp_chan) - tmp_chan = dma_request_slave_channel(dev_be, tx ? "tx" : "rx"); + if (!tmp_chan) { + tmp_chan = dma_request_chan(dev_be, tx ? "tx" : "rx"); + if (IS_ERR(tmp_chan)) { + dev_err(dev, "failed to request DMA channel for Back-End\n"); + return -EINVAL; + } + } /* * An EDMA DEV_TO_DEV channel is fixed and bound with DMA event of each * peripheral, unlike SDMA channel that is allocated dynamically. So no * need to configure dma_request and dma_request2, but get dma_chan of - * Back-End device directly via dma_request_slave_channel. + * Back-End device directly via dma_request_chan. */ if (!asrc->use_edma) { /* Get DMA request of Back-End */

3 2

[PATCH] ASoC: fsl_sai: Fix pins setting for i.MX8QM platform
by Chancel Liu 19 Apr '23

19 Apr '23

SAI on i.MX8QM platform supports the data lines up to 4. So the pins setting should be corrected to 4. Fixes: eba0f0077519 ("ASoC: fsl_sai: Enable combine mode soft") Signed-off-by: Chancel Liu <chancel.liu(a)nxp.com> --- sound/soc/fsl/fsl_sai.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/fsl/fsl_sai.c b/sound/soc/fsl/fsl_sai.c index 07d13dca852e..abdaffb00fbd 100644 --- a/sound/soc/fsl/fsl_sai.c +++ b/sound/soc/fsl/fsl_sai.c @@ -1544,7 +1544,7 @@ static const struct fsl_sai_soc_data fsl_sai_imx8qm_data = { .use_imx_pcm = true, .use_edma = true, .fifo_depth = 64, - .pins = 1, + .pins = 4, .reg_offset = 0, .mclk0_is_mclk1 = false, .flags = 0, -- 2.25.1

4 3

snd-firewire-ctl-services 0.1.0 released
by Takashi Sakamoto 19 Apr '23

19 Apr '23

Hi all, This is a short announcement about a new release of snd-firewire-ctl-services project. After development for mostly three years[1], version 0.1.0 is released today. If you have FireWire audio device and interests in ALSA support, the release would be worth to check out. * https://github.com/alsa-project/snd-firewire-ctl-services/releases/tag/snd-… The project provides user space service programs to operate digital signal processing function in devices supported by ALSA firewire stack. If using such device, you can configure DSP functions such as the volumes of device. For some device, effects such as dynamics and equalizers are also configurable. Available devices are listed in README.rst of the project. The service programs work as 'message broaker'. ALSA control applications are available for end-user interface to communicate to the service programs[2]. The device connected to IEEE 1394 bus is the peer. The service programs receives messages from both ends, then translates and convert the messages to send to the opposite end. Against your expectation, the project provides neither GUI programs nor end-user interfaces. I know that the user experience is heavily on look-and-feel on the GUI programs, while it is out of the aim of project. I daily use quashctl in QasTools[3] and it is pretty good to me for such ALSA control application. If encountering any issue, please file it to github repository[4]. README should be helpful to new users. Thanks for your support and long patience to ALSA firewire stack. [1] https://lists.linuxaudio.org/hyperkitty/list/linux-audio-dev@lists.linuxaud… [2] For TASCAM FireWire series, ALSA sequencer application is such end as well to operate control surface. [3] https://gitlab.com/sebholt/qastools [4] https://github.com/alsa-project/snd-firewire-ctl-services Regards Takashi Sakamoto

2 1

[PATCH] ALSA: hda/realtek: Remove specific patch for Dell Precision 3260
by Jaroslav Kysela 19 Apr '23

19 Apr '23

Unfortunately, the tester gave a weak feedback (working/non-working) for this case. After the double confirmation, this change is not really required. The standard code with alc269_fallback_pin_fixup_tbl should work on this hardware. Fixes: 5911d78fabbb ("ALSA: hda/realtek: Improve support for Dell Precision 3260") Fixes: 5f4efc9dfcfd ("ALSA: hda/realtek: Fix support for Dell Precision 3260") Signed-off-by: Jaroslav Kysela <perex(a)perex.cz> --- sound/pci/hda/patch_realtek.c | 1 - 1 file changed, 1 deletion(-) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 26187f5d56b5..50b8573b5206 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -9263,7 +9263,6 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x1028, 0x0a62, "Dell Precision 5560", ALC289_FIXUP_DUAL_SPK), SND_PCI_QUIRK(0x1028, 0x0a9d, "Dell Latitude 5430", ALC269_FIXUP_DELL4_MIC_NO_PRESENCE), SND_PCI_QUIRK(0x1028, 0x0a9e, "Dell Latitude 5430", ALC269_FIXUP_DELL4_MIC_NO_PRESENCE), - SND_PCI_QUIRK(0x1028, 0x0ac9, "Dell Precision 3260", ALC283_FIXUP_CHROME_BOOK), SND_PCI_QUIRK(0x1028, 0x0b19, "Dell XPS 15 9520", ALC289_FIXUP_DUAL_SPK), SND_PCI_QUIRK(0x1028, 0x0b1a, "Dell Precision 5570", ALC289_FIXUP_DUAL_SPK), SND_PCI_QUIRK(0x1028, 0x0b37, "Dell Inspiron 16 Plus 7620 2-in-1", ALC295_FIXUP_DELL_INSPIRON_TOP_SPEAKERS), -- 2.39.2

2 1

[PATCH] ASoC: rt722-sdca: Add RT722 SDCA driver
by Jack Yu 19 Apr '23

19 Apr '23

This is the initial codec driver for rt722-sdca. Signed-off-by: Jack Yu <jack.yu(a)realtek.com> --- sound/soc/codecs/Kconfig | 7 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/rt722-sdca-sdw.c | 505 ++++++++++ sound/soc/codecs/rt722-sdca-sdw.h | 124 +++ sound/soc/codecs/rt722-sdca.c | 1549 +++++++++++++++++++++++++++++ sound/soc/codecs/rt722-sdca.h | 237 +++++ 6 files changed, 2424 insertions(+) create mode 100644 sound/soc/codecs/rt722-sdca-sdw.c create mode 100644 sound/soc/codecs/rt722-sdca-sdw.h create mode 100644 sound/soc/codecs/rt722-sdca.c create mode 100644 sound/soc/codecs/rt722-sdca.h diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 79d2362ad055..a163e2afdf72 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -207,6 +207,7 @@ config SND_SOC_ALL_CODECS imply SND_SOC_RT712_SDCA_DMIC_SDW imply SND_SOC_RT715_SDW imply SND_SOC_RT715_SDCA_SDW + imply SND_SOC_RT722_SDCA_SDW imply SND_SOC_RT1308_SDW imply SND_SOC_RT1316_SDW imply SND_SOC_RT1318_SDW @@ -1539,6 +1540,12 @@ config SND_SOC_RT712_SDCA_DMIC_SDW select REGMAP_SOUNDWIRE select REGMAP_SOUNDWIRE_MBQ +config SND_SOC_RT722_SDCA_SDW + tristate "Realtek RT722 SDCA Codec - SDW" + depends on SOUNDWIRE + select REGMAP_SOUNDWIRE + select REGMAP_SOUNDWIRE_MBQ + config SND_SOC_RT715 tristate diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 5cdbae88e6e3..cd799306331c 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -237,6 +237,7 @@ snd-soc-rt712-sdca-objs := rt712-sdca.o rt712-sdca-sdw.o snd-soc-rt712-sdca-dmic-objs := rt712-sdca-dmic.o snd-soc-rt715-objs := rt715.o rt715-sdw.o snd-soc-rt715-sdca-objs := rt715-sdca.o rt715-sdca-sdw.o +snd-soc-rt722-sdca-objs := rt722-sdca.o rt722-sdca-sdw.o snd-soc-rt9120-objs := rt9120.o snd-soc-sdw-mockup-objs := sdw-mockup.o snd-soc-sgtl5000-objs := sgtl5000.o @@ -607,6 +608,7 @@ obj-$(CONFIG_SND_SOC_RT712_SDCA_SDW) += snd-soc-rt712-sdca.o obj-$(CONFIG_SND_SOC_RT712_SDCA_DMIC_SDW) += snd-soc-rt712-sdca-dmic.o obj-$(CONFIG_SND_SOC_RT715) += snd-soc-rt715.o obj-$(CONFIG_SND_SOC_RT715_SDCA_SDW) += snd-soc-rt715-sdca.o +obj-$(CONFIG_SND_SOC_RT722_SDCA_SDW) += snd-soc-rt722-sdca.o obj-$(CONFIG_SND_SOC_RT9120) += snd-soc-rt9120.o obj-$(CONFIG_SND_SOC_SDW_MOCKUP) += snd-soc-sdw-mockup.o obj-$(CONFIG_SND_SOC_SGTL5000) += snd-soc-sgtl5000.o diff --git a/sound/soc/codecs/rt722-sdca-sdw.c b/sound/soc/codecs/rt722-sdca-sdw.c new file mode 100644 index 000000000000..9e2dd5bc59ac --- /dev/null +++ b/sound/soc/codecs/rt722-sdca-sdw.c @@ -0,0 +1,505 @@ +// SPDX-License-Identifier: GPL-2.0-only +// +// rt722-sdca-sdw.c -- rt722 SDCA ALSA SoC audio driver +// +// Copyright(c) 2023 Realtek Semiconductor Corp. +// +// + +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/module.h> +#include <linux/mod_devicetable.h> +#include <linux/pm_runtime.h> +#include <linux/soundwire/sdw_registers.h> + +#include "rt722-sdca.h" +#include "rt722-sdca-sdw.h" + +static bool rt722_sdca_readable_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x2f01 ... 0x2f0a: + case 0x2f35 ... 0x2f36: + case 0x2f50: + case 0x2f54: + case 0x2f58 ... 0x2f5d: + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, RT722_SDCA_CTL_SELECTED_MODE, + 0): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, RT722_SDCA_CTL_DETECTED_MODE, + 0): + case SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, RT722_SDCA_CTL_HIDTX_CURRENT_OWNER, + 0) ... SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_MESSAGE_LENGTH, 0): + case RT722_BUF_ADDR_HID1 ... RT722_BUF_ADDR_HID2: + return true; + default: + return false; + } +} + +static bool rt722_sdca_volatile_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x2f01: + case 0x2f54: + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, RT722_SDCA_CTL_DETECTED_MODE, + 0): + case SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, RT722_SDCA_CTL_HIDTX_CURRENT_OWNER, + 0) ... SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_MESSAGE_LENGTH, 0): + case RT722_BUF_ADDR_HID1 ... RT722_BUF_ADDR_HID2: + return true; + default: + return false; + } +} + +static bool rt722_sdca_mbq_readable_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x2000000 ... 0x2000024: + case 0x2000029 ... 0x200004a: + case 0x2000051 ... 0x2000052: + case 0x200005a ... 0x200005b: + case 0x2000061 ... 0x2000069: + case 0x200006b: + case 0x2000070: + case 0x200007f: + case 0x2000082 ... 0x200008e: + case 0x2000090 ... 0x2000094: + case 0x5300000 ... 0x5300002: + case 0x5400002: + case 0x5600000 ... 0x5600007: + case 0x5700000 ... 0x5700004: + case 0x5800000 ... 0x5800004: + case 0x5b00003: + case 0x5c00011: + case 0x5d00006: + case 0x5f00000 ... 0x5f0000d: + case 0x5f00030: + case 0x6100000 ... 0x6100051: + case 0x6100055 ... 0x6100057: + case 0x6100062: + case 0x6100064 ... 0x6100065: + case 0x6100067: + case 0x6100070 ... 0x610007c: + case 0x6100080: + case SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_01): + case SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_02): + case SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_03): + case SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_04): + case SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_VOLUME, CH_L): + case SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_VOLUME, CH_R): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_VOLUME, + CH_L): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_VOLUME, + CH_R): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_VOLUME, + CH_L): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_VOLUME, + CH_R): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, + RT722_SDCA_CTL_FU_CH_GAIN, CH_L): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, + RT722_SDCA_CTL_FU_CH_GAIN, CH_R): + return true; + default: + return false; + } +} + +static bool rt722_sdca_mbq_volatile_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x2000000: + case 0x200000d: + case 0x2000019: + case 0x2000020: + case 0x2000030: + case 0x2000046: + case 0x2000067: + case 0x2000084: + case 0x2000086: + return true; + default: + return false; + } +} + +static const struct regmap_config rt722_sdca_regmap = { + .reg_bits = 32, + .val_bits = 8, + .readable_reg = rt722_sdca_readable_register, + .volatile_reg = rt722_sdca_volatile_register, + .max_register = 0x44ffffff, + .reg_defaults = rt722_sdca_reg_defaults, + .num_reg_defaults = ARRAY_SIZE(rt722_sdca_reg_defaults), + .cache_type = REGCACHE_RBTREE, + .use_single_read = true, + .use_single_write = true, +}; + +static const struct regmap_config rt722_sdca_mbq_regmap = { + .name = "sdw-mbq", + .reg_bits = 32, + .val_bits = 16, + .readable_reg = rt722_sdca_mbq_readable_register, + .volatile_reg = rt722_sdca_mbq_volatile_register, + .max_register = 0x41000312, + .reg_defaults = rt722_sdca_mbq_defaults, + .num_reg_defaults = ARRAY_SIZE(rt722_sdca_mbq_defaults), + .cache_type = REGCACHE_RBTREE, + .use_single_read = true, + .use_single_write = true, +}; + +static int rt722_sdca_update_status(struct sdw_slave *slave, + enum sdw_slave_status status) +{ + struct rt722_sdca_priv *rt722 = dev_get_drvdata(&slave->dev); + + /* Update the status */ + rt722->status = status; + + if (status == SDW_SLAVE_UNATTACHED) + rt722->hw_init = false; + + if (status == SDW_SLAVE_ATTACHED) { + if (rt722->hs_jack) { + /* + * Due to the SCP_SDCA_INTMASK will be cleared by any reset, and then + * if the device attached again, we will need to set the setting back. + * It could avoid losing the jack detection interrupt. + * This also could sync with the cache value as the rt722_sdca_jack_init set. + */ + sdw_write_no_pm(rt722->slave, SDW_SCP_SDCA_INTMASK1, + SDW_SCP_SDCA_INTMASK_SDCA_0 | SDW_SCP_SDCA_INTMASK_SDCA_6); + sdw_write_no_pm(rt722->slave, SDW_SCP_SDCA_INTMASK2, + SDW_SCP_SDCA_INTMASK_SDCA_8); + } + } + + /* + * Perform initialization only if slave status is present and + * hw_init flag is false + */ + if (rt722->hw_init || rt722->status != SDW_SLAVE_ATTACHED) + return 0; + + /* perform I/O transfers required for Slave initialization */ + return rt722_sdca_io_init(&slave->dev, slave); +} + +static int rt722_sdca_read_prop(struct sdw_slave *slave) +{ + struct sdw_slave_prop *prop = &slave->prop; + int nval; + int i, j; + u32 bit; + unsigned long addr; + struct sdw_dpn_prop *dpn; + + prop->scp_int1_mask = SDW_SCP_INT1_BUS_CLASH | SDW_SCP_INT1_PARITY; + prop->quirks = SDW_SLAVE_QUIRKS_INVALID_INITIAL_PARITY; + + prop->paging_support = true; + + /* first we need to allocate memory for set bits in port lists */ + prop->source_ports = BIT(6) | BIT(2); /* BITMAP: 01000100 */ + prop->sink_ports = BIT(3) | BIT(1); /* BITMAP: 00001010 */ + + nval = hweight32(prop->source_ports); + prop->src_dpn_prop = devm_kcalloc(&slave->dev, nval, + sizeof(*prop->src_dpn_prop), GFP_KERNEL); + if (!prop->src_dpn_prop) + return -ENOMEM; + + i = 0; + dpn = prop->src_dpn_prop; + addr = prop->source_ports; + for_each_set_bit(bit, &addr, 32) { + dpn[i].num = bit; + dpn[i].type = SDW_DPN_FULL; + dpn[i].simple_ch_prep_sm = true; + dpn[i].ch_prep_timeout = 10; + i++; + } + + /* do this again for sink now */ + nval = hweight32(prop->sink_ports); + prop->sink_dpn_prop = devm_kcalloc(&slave->dev, nval, + sizeof(*prop->sink_dpn_prop), GFP_KERNEL); + if (!prop->sink_dpn_prop) + return -ENOMEM; + + j = 0; + dpn = prop->sink_dpn_prop; + addr = prop->sink_ports; + for_each_set_bit(bit, &addr, 32) { + dpn[j].num = bit; + dpn[j].type = SDW_DPN_FULL; + dpn[j].simple_ch_prep_sm = true; + dpn[j].ch_prep_timeout = 10; + j++; + } + + /* set the timeout values */ + prop->clk_stop_timeout = 200; + + /* wake-up event */ + prop->wake_capable = 1; + + return 0; +} + +static int rt722_sdca_interrupt_callback(struct sdw_slave *slave, + struct sdw_slave_intr_status *status) +{ + struct rt722_sdca_priv *rt722 = dev_get_drvdata(&slave->dev); + int ret, stat; + int count = 0, retry = 3; + unsigned int sdca_cascade, scp_sdca_stat1, scp_sdca_stat2 = 0; + + if (cancel_delayed_work_sync(&rt722->jack_detect_work)) { + dev_warn(&slave->dev, "%s the pending delayed_work was cancelled", __func__); + /* avoid the HID owner doesn't change to device */ + if (rt722->scp_sdca_stat2) + scp_sdca_stat2 = rt722->scp_sdca_stat2; + } + + /* + * The critical section below intentionally protects a rather large piece of code. + * We don't want to allow the system suspend to disable an interrupt while we are + * processing it, which could be problematic given the quirky SoundWire interrupt + * scheme. We do want however to prevent new workqueues from being scheduled if + * the disable_irq flag was set during system suspend. + */ + mutex_lock(&rt722->disable_irq_lock); + + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT1); + if (ret < 0) + goto io_error; + rt722->scp_sdca_stat1 = ret; + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT2); + if (ret < 0) + goto io_error; + rt722->scp_sdca_stat2 = ret; + if (scp_sdca_stat2) + rt722->scp_sdca_stat2 |= scp_sdca_stat2; + do { + /* clear flag */ + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT1); + if (ret < 0) + goto io_error; + if (ret & SDW_SCP_SDCA_INTMASK_SDCA_0) { + ret = sdw_update_no_pm(rt722->slave, SDW_SCP_SDCA_INT1, + SDW_SCP_SDCA_INT_SDCA_0, SDW_SCP_SDCA_INT_SDCA_0); + if (ret < 0) + goto io_error; + } else if (ret & SDW_SCP_SDCA_INTMASK_SDCA_6) { + ret = sdw_update_no_pm(rt722->slave, SDW_SCP_SDCA_INT1, + SDW_SCP_SDCA_INT_SDCA_6, SDW_SCP_SDCA_INT_SDCA_6); + if (ret < 0) + goto io_error; + } + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT2); + if (ret < 0) + goto io_error; + if (ret & SDW_SCP_SDCA_INTMASK_SDCA_8) { + ret = sdw_write_no_pm(rt722->slave, SDW_SCP_SDCA_INT2, + SDW_SCP_SDCA_INTMASK_SDCA_8); + if (ret < 0) + goto io_error; + } + + /* check if flag clear or not */ + ret = sdw_read_no_pm(rt722->slave, SDW_DP0_INT); + if (ret < 0) + goto io_error; + sdca_cascade = ret & SDW_DP0_SDCA_CASCADE; + + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT1); + if (ret < 0) + goto io_error; + scp_sdca_stat1 = ret & SDW_SCP_SDCA_INTMASK_SDCA_0; + + ret = sdw_read_no_pm(rt722->slave, SDW_SCP_SDCA_INT2); + if (ret < 0) + goto io_error; + scp_sdca_stat2 = ret & SDW_SCP_SDCA_INTMASK_SDCA_8; + + stat = scp_sdca_stat1 || scp_sdca_stat2 || sdca_cascade; + + count++; + } while (stat != 0 && count < retry); + + if (stat) + dev_warn(&slave->dev, + "%s scp_sdca_stat1=0x%x, scp_sdca_stat2=0x%x\n", __func__, + rt722->scp_sdca_stat1, rt722->scp_sdca_stat2); + + if (status->sdca_cascade && !rt722->disable_irq) + mod_delayed_work(system_power_efficient_wq, + &rt722->jack_detect_work, msecs_to_jiffies(30)); + + mutex_unlock(&rt722->disable_irq_lock); + + return 0; + +io_error: + mutex_unlock(&rt722->disable_irq_lock); + pr_err_ratelimited("IO error in %s, ret %d\n", __func__, ret); + return ret; +} + +static struct sdw_slave_ops rt722_sdca_slave_ops = { + .read_prop = rt722_sdca_read_prop, + .interrupt_callback = rt722_sdca_interrupt_callback, + .update_status = rt722_sdca_update_status, +}; + +static int rt722_sdca_sdw_probe(struct sdw_slave *slave, + const struct sdw_device_id *id) +{ + struct regmap *regmap, *mbq_regmap; + + /* Regmap Initialization */ + mbq_regmap = devm_regmap_init_sdw_mbq(slave, &rt722_sdca_mbq_regmap); + if (IS_ERR(mbq_regmap)) + return PTR_ERR(mbq_regmap); + + regmap = devm_regmap_init_sdw(slave, &rt722_sdca_regmap); + if (IS_ERR(regmap)) + return PTR_ERR(regmap); + + return rt722_sdca_init(&slave->dev, regmap, mbq_regmap, slave); +} + +static int rt722_sdca_sdw_remove(struct sdw_slave *slave) +{ + struct rt722_sdca_priv *rt722 = dev_get_drvdata(&slave->dev); + + if (rt722->hw_init) { + cancel_delayed_work_sync(&rt722->jack_detect_work); + cancel_delayed_work_sync(&rt722->jack_btn_check_work); + } + + if (rt722->first_hw_init) + pm_runtime_disable(&slave->dev); + + mutex_destroy(&rt722->calibrate_mutex); + mutex_destroy(&rt722->disable_irq_lock); + + return 0; +} + +static const struct sdw_device_id rt722_sdca_id[] = { + SDW_SLAVE_ENTRY_EXT(0x025d, 0x722, 0x3, 0x1, 0), + {}, +}; +MODULE_DEVICE_TABLE(sdw, rt722_sdca_id); + +static int __maybe_unused rt722_sdca_dev_suspend(struct device *dev) +{ + struct rt722_sdca_priv *rt722 = dev_get_drvdata(dev); + + if (!rt722->hw_init) + return 0; + + cancel_delayed_work_sync(&rt722->jack_detect_work); + cancel_delayed_work_sync(&rt722->jack_btn_check_work); + + regcache_cache_only(rt722->regmap, true); + regcache_cache_only(rt722->mbq_regmap, true); + + return 0; +} + +static int __maybe_unused rt722_sdca_dev_system_suspend(struct device *dev) +{ + struct rt722_sdca_priv *rt722_sdca = dev_get_drvdata(dev); + struct sdw_slave *slave = dev_to_sdw_dev(dev); + int ret1, ret2; + + if (!rt722_sdca->hw_init) + return 0; + + /* + * prevent new interrupts from being handled after the + * deferred work completes and before the parent disables + * interrupts on the link + */ + mutex_lock(&rt722_sdca->disable_irq_lock); + rt722_sdca->disable_irq = true; + ret1 = sdw_update_no_pm(slave, SDW_SCP_SDCA_INTMASK1, + SDW_SCP_SDCA_INTMASK_SDCA_0 | SDW_SCP_SDCA_INTMASK_SDCA_6, 0); + ret2 = sdw_update_no_pm(slave, SDW_SCP_SDCA_INTMASK2, + SDW_SCP_SDCA_INTMASK_SDCA_8, 0); + mutex_unlock(&rt722_sdca->disable_irq_lock); + + if (ret1 < 0 || ret2 < 0) { + /* log but don't prevent suspend from happening */ + dev_dbg(&slave->dev, "%s: could not disable SDCA interrupts\n:", __func__); + } + + return rt722_sdca_dev_suspend(dev); +} + +#define RT722_PROBE_TIMEOUT 5000 + +static int __maybe_unused rt722_sdca_dev_resume(struct device *dev) +{ + struct sdw_slave *slave = dev_to_sdw_dev(dev); + struct rt722_sdca_priv *rt722 = dev_get_drvdata(dev); + unsigned long time; + + if (!rt722->first_hw_init) + return 0; + + if (!slave->unattach_request) + goto regmap_sync; + + time = wait_for_completion_timeout(&slave->initialization_complete, + msecs_to_jiffies(RT722_PROBE_TIMEOUT)); + if (!time) { + dev_err(&slave->dev, "Initialization not complete, timed out\n"); + sdw_show_ping_status(slave->bus, true); + + return -ETIMEDOUT; + } + +regmap_sync: + slave->unattach_request = 0; + regcache_cache_only(rt722->regmap, false); + regcache_sync(rt722->regmap); + regcache_cache_only(rt722->mbq_regmap, false); + regcache_sync(rt722->mbq_regmap); + return 0; +} + +static const struct dev_pm_ops rt722_sdca_pm = { + SET_SYSTEM_SLEEP_PM_OPS(rt722_sdca_dev_system_suspend, rt722_sdca_dev_resume) + SET_RUNTIME_PM_OPS(rt722_sdca_dev_suspend, rt722_sdca_dev_resume, NULL) +}; + +static struct sdw_driver rt722_sdca_sdw_driver = { + .driver = { + .name = "rt722-sdca", + .owner = THIS_MODULE, + .pm = &rt722_sdca_pm, + }, + .probe = rt722_sdca_sdw_probe, + .remove = rt722_sdca_sdw_remove, + .ops = &rt722_sdca_slave_ops, + .id_table = rt722_sdca_id, +}; +module_sdw_driver(rt722_sdca_sdw_driver); + +MODULE_DESCRIPTION("ASoC RT722 SDCA SDW driver"); +MODULE_AUTHOR("Jack Yu <jack.yu(a)realtek.com>"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/rt722-sdca-sdw.h b/sound/soc/codecs/rt722-sdca-sdw.h new file mode 100644 index 000000000000..5b43e86f75d1 --- /dev/null +++ b/sound/soc/codecs/rt722-sdca-sdw.h @@ -0,0 +1,124 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * rt722-sdca-sdw.h -- RT722 SDCA ALSA SoC audio driver header + * + * Copyright(c) 2023 Realtek Semiconductor Corp. + */ + +#ifndef __RT722_SDW_H__ +#define __RT722_SDW_H__ + +#include <linux/regmap.h> +#include <linux/soundwire/sdw_registers.h> + +static const struct reg_default rt722_sdca_reg_defaults[] = { + { 0x202d, 0x00 }, + { 0x2f01, 0x00 }, + { 0x2f02, 0x09 }, + { 0x2f03, 0x00 }, + { 0x2f04, 0x00 }, + { 0x2f05, 0x0b }, + { 0x2f06, 0x01 }, + { 0x2f08, 0x00 }, + { 0x2f09, 0x00 }, + { 0x2f0a, 0x00 }, + { 0x2f35, 0x00 }, + { 0x2f36, 0x00 }, + { 0x2f50, 0xf0 }, + { 0x2f58, 0x07 }, + { 0x2f59, 0x07 }, + { 0x2f5a, 0x07 }, + { 0x2f5b, 0x07 }, + { 0x2f5c, 0x27 }, + { 0x2f5d, 0x07 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_CS01, RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, + 0), 0x09 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_CS11, RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, + 0), 0x09 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE12, RT722_SDCA_CTL_REQ_POWER_STATE, + 0), 0x03 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE40, RT722_SDCA_CTL_REQ_POWER_STATE, + 0), 0x03 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_MUTE, CH_L), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_MUTE, CH_R), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_MUTE, CH_L), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_MUTE, CH_R), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_CS1F, RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, + 0), 0x09 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_MUTE, CH_01), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_MUTE, CH_02), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_MUTE, CH_03), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_MUTE, CH_04), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_PDE2A, RT722_SDCA_CTL_REQ_POWER_STATE, 0), + 0x03 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_IT26, RT722_SDCA_CTL_VENDOR_DEF, 0), + 0x00 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_CS31, RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), + 0x09 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_MUTE, CH_L), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_MUTE, CH_R), + 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_PDE23, RT722_SDCA_CTL_REQ_POWER_STATE, 0), + 0x03 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_OT23, RT722_SDCA_CTL_VENDOR_DEF, 0), 0x00 }, +}; + +static const struct reg_default rt722_sdca_mbq_defaults[] = { + { 0x200003c, 0xc214 }, + { 0x2000046, 0x8004 }, + { 0x6100006, 0x0005 }, + { 0x6100010, 0x2630 }, + { 0x6100011, 0x152f }, + { 0x6100013, 0x0102 }, + { 0x6100015, 0x2200 }, + { 0x6100017, 0x0102 }, + { 0x6100025, 0x2a29 }, + { 0x6100026, 0x2a00 }, + { 0x6100028, 0x2a2a }, + { 0x6100029, 0x4141 }, + { 0x6100055, 0x0000 }, + { 0x5810000, 0x702d }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_VOLUME, + CH_L), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, RT722_SDCA_CTL_FU_VOLUME, + CH_R), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_VOLUME, + CH_L), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, RT722_SDCA_CTL_FU_VOLUME, + CH_R), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, RT722_SDCA_CTL_FU_CH_GAIN, + CH_L), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, RT722_SDCA_CTL_FU_CH_GAIN, + CH_R), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_01), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_02), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_03), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, RT722_SDCA_CTL_FU_VOLUME, + CH_04), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15, RT722_SDCA_CTL_FU_CH_GAIN, CH_01), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15, RT722_SDCA_CTL_FU_CH_GAIN, CH_02), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15, RT722_SDCA_CTL_FU_CH_GAIN, CH_03), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15, RT722_SDCA_CTL_FU_CH_GAIN, CH_04), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_VOLUME, CH_L), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, RT722_SDCA_CTL_FU_VOLUME, CH_R), + 0x0000 }, +}; + +#endif /* __RT722_SDW_H__ */ diff --git a/sound/soc/codecs/rt722-sdca.c b/sound/soc/codecs/rt722-sdca.c new file mode 100644 index 000000000000..d0256fa203b9 --- /dev/null +++ b/sound/soc/codecs/rt722-sdca.c @@ -0,0 +1,1549 @@ +// SPDX-License-Identifier: GPL-2.0-only +// +// rt722-sdca.c -- rt722 SDCA ALSA SoC audio driver +// +// Copyright(c) 2023 Realtek Semiconductor Corp. +// +// + +#include <linux/bitops.h> +#include <sound/core.h> +#include <linux/delay.h> +#include <linux/init.h> +#include <sound/initval.h> +#include <sound/jack.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <sound/pcm.h> +#include <linux/pm_runtime.h> +#include <sound/pcm_params.h> +#include <linux/soundwire/sdw_registers.h> +#include <linux/slab.h> +#include <sound/soc-dapm.h> +#include <sound/tlv.h> + +#include "rt722-sdca.h" + +int rt722_sdca_index_write(struct rt722_sdca_priv *rt722, + unsigned int nid, unsigned int reg, unsigned int value) +{ + struct regmap *regmap = rt722->mbq_regmap; + unsigned int addr = (nid << 20) | reg; + int ret; + + ret = regmap_write(regmap, addr, value); + if (ret < 0) + dev_err(&rt722->slave->dev, + "Failed to set private value: %06x <= %04x ret=%d\n", + addr, value, ret); + + return ret; +} + +int rt722_sdca_index_read(struct rt722_sdca_priv *rt722, + unsigned int nid, unsigned int reg, unsigned int *value) +{ + int ret; + struct regmap *regmap = rt722->mbq_regmap; + unsigned int addr = (nid << 20) | reg; + + ret = regmap_read(regmap, addr, value); + if (ret < 0) + dev_err(&rt722->slave->dev, + "Failed to get private value: %06x => %04x ret=%d\n", + addr, *value, ret); + + return ret; +} + +static int rt722_sdca_index_update_bits(struct rt722_sdca_priv *rt722, + unsigned int nid, unsigned int reg, unsigned int mask, unsigned int val) +{ + unsigned int tmp; + int ret; + + ret = rt722_sdca_index_read(rt722, nid, reg, &tmp); + if (ret < 0) + return ret; + + set_mask_bits(&tmp, mask, val); + return rt722_sdca_index_write(rt722, nid, reg, tmp); +} + +static int rt722_sdca_btn_type(unsigned char *buffer) +{ + if ((*buffer & 0xf0) == 0x10 || (*buffer & 0x0f) == 0x01 || (*(buffer + 1) == 0x01) || + (*(buffer + 1) == 0x10)) + return SND_JACK_BTN_2; + else if ((*buffer & 0xf0) == 0x20 || (*buffer & 0x0f) == 0x02 || (*(buffer + 1) == 0x02) || + (*(buffer + 1) == 0x20)) + return SND_JACK_BTN_3; + else if ((*buffer & 0xf0) == 0x40 || (*buffer & 0x0f) == 0x04 || (*(buffer + 1) == 0x04) || + (*(buffer + 1) == 0x40)) + return SND_JACK_BTN_0; + else if ((*buffer & 0xf0) == 0x80 || (*buffer & 0x0f) == 0x08 || (*(buffer + 1) == 0x08) || + (*(buffer + 1) == 0x80)) + return SND_JACK_BTN_1; + + return 0; +} + +static unsigned int rt722_sdca_button_detect(struct rt722_sdca_priv *rt722) +{ + unsigned int btn_type = 0, offset, idx, val, owner; + int ret; + unsigned char buf[3]; + + /* get current UMP message owner */ + ret = regmap_read(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_CURRENT_OWNER, 0), &owner); + if (ret < 0) + return 0; + + /* if owner is device then there is no button event from device */ + if (owner == 1) + return 0; + + /* read UMP message offset */ + ret = regmap_read(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_MESSAGE_OFFSET, 0), &offset); + if (ret < 0) + goto _end_btn_det_; + + for (idx = 0; idx < sizeof(buf); idx++) { + ret = regmap_read(rt722->regmap, + RT722_BUF_ADDR_HID1 + offset + idx, &val); + if (ret < 0) + goto _end_btn_det_; + buf[idx] = val & 0xff; + } + + if (buf[0] == 0x11) + btn_type = rt722_sdca_btn_type(&buf[1]); + +_end_btn_det_: + /* Host is owner, so set back to device */ + if (owner == 0) + /* set owner to device */ + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_CURRENT_OWNER, 0), 0x01); + + return btn_type; +} + +static int rt722_sdca_headset_detect(struct rt722_sdca_priv *rt722) +{ + unsigned int det_mode; + int ret; + + /* get detected_mode */ + ret = regmap_read(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, + RT722_SDCA_CTL_DETECTED_MODE, 0), &det_mode); + if (ret < 0) + goto io_error; + + switch (det_mode) { + case 0x00: + rt722->jack_type = 0; + break; + case 0x03: + rt722->jack_type = SND_JACK_HEADPHONE; + break; + case 0x05: + rt722->jack_type = SND_JACK_HEADSET; + break; + } + + /* write selected_mode */ + if (det_mode) { + ret = regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, + RT722_SDCA_CTL_SELECTED_MODE, 0), det_mode); + if (ret < 0) + goto io_error; + } + + dev_dbg(&rt722->slave->dev, + "%s, detected_mode=0x%x\n", __func__, det_mode); + + return 0; + +io_error: + pr_err_ratelimited("IO error in %s, ret %d\n", __func__, ret); + return ret; +} + +static void rt722_sdca_jack_detect_handler(struct work_struct *work) +{ + struct rt722_sdca_priv *rt722 = + container_of(work, struct rt722_sdca_priv, jack_detect_work.work); + int btn_type = 0, ret; + + if (!rt722->hs_jack) + return; + + if (!rt722->component->card || !rt722->component->card->instantiated) + return; + + /* SDW_SCP_SDCA_INT_SDCA_6 is used for jack detection */ + if (rt722->scp_sdca_stat1 & SDW_SCP_SDCA_INT_SDCA_6 || + rt722->scp_sdca_stat1 & SDW_SCP_SDCA_INT_SDCA_0) { + ret = rt722_sdca_headset_detect(rt722); + if (ret < 0) + return; + } + + /* SDW_SCP_SDCA_INT_SDCA_8 is used for button detection */ + if (rt722->scp_sdca_stat2 & SDW_SCP_SDCA_INT_SDCA_8) + btn_type = rt722_sdca_button_detect(rt722); + + if (rt722->jack_type == 0) + btn_type = 0; + + dev_dbg(&rt722->slave->dev, + "in %s, jack_type=%d\n", __func__, rt722->jack_type); + dev_dbg(&rt722->slave->dev, + "in %s, btn_type=0x%x\n", __func__, btn_type); + dev_dbg(&rt722->slave->dev, + "in %s, scp_sdca_stat1=0x%x, scp_sdca_stat2=0x%x\n", __func__, + rt722->scp_sdca_stat1, rt722->scp_sdca_stat2); + + snd_soc_jack_report(rt722->hs_jack, rt722->jack_type | btn_type, + SND_JACK_HEADSET | + SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3); + + if (btn_type) { + /* button released */ + snd_soc_jack_report(rt722->hs_jack, rt722->jack_type, + SND_JACK_HEADSET | + SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3); + + mod_delayed_work(system_power_efficient_wq, + &rt722->jack_btn_check_work, msecs_to_jiffies(200)); + } +} + +static void rt722_sdca_btn_check_handler(struct work_struct *work) +{ + struct rt722_sdca_priv *rt722 = + container_of(work, struct rt722_sdca_priv, jack_btn_check_work.work); + int btn_type = 0, ret, idx; + unsigned int det_mode, offset, val; + unsigned char buf[3]; + + ret = regmap_read(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_GE49, + RT722_SDCA_CTL_DETECTED_MODE, 0), &det_mode); + if (ret < 0) + goto io_error; + + /* pin attached */ + if (det_mode) { + /* read UMP message offset */ + ret = regmap_read(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_HID, RT722_SDCA_ENT_HID01, + RT722_SDCA_CTL_HIDTX_MESSAGE_OFFSET, 0), &offset); + if (ret < 0) + goto io_error; + + for (idx = 0; idx < sizeof(buf); idx++) { + ret = regmap_read(rt722->regmap, + RT722_BUF_ADDR_HID1 + offset + idx, &val); + if (ret < 0) + goto io_error; + buf[idx] = val & 0xff; + } + + if (buf[0] == 0x11) + btn_type = rt722_sdca_btn_type(&buf[1]); + } else + rt722->jack_type = 0; + + dev_dbg(&rt722->slave->dev, "%s, btn_type=0x%x\n", __func__, btn_type); + snd_soc_jack_report(rt722->hs_jack, rt722->jack_type | btn_type, + SND_JACK_HEADSET | + SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3); + + if (btn_type) { + /* button released */ + snd_soc_jack_report(rt722->hs_jack, rt722->jack_type, + SND_JACK_HEADSET | + SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3); + + mod_delayed_work(system_power_efficient_wq, + &rt722->jack_btn_check_work, msecs_to_jiffies(200)); + } + + return; + +io_error: + pr_err_ratelimited("IO error in %s, ret %d\n", __func__, ret); +} + +static void rt722_sdca_jack_init(struct rt722_sdca_priv *rt722) +{ + mutex_lock(&rt722->calibrate_mutex); + if (rt722->hs_jack) { + /* set SCP_SDCA_IntMask1[0]=1 */ + sdw_write_no_pm(rt722->slave, SDW_SCP_SDCA_INTMASK1, + SDW_SCP_SDCA_INTMASK_SDCA_0 | SDW_SCP_SDCA_INTMASK_SDCA_6); + /* set SCP_SDCA_IntMask2[0]=1 */ + sdw_write_no_pm(rt722->slave, SDW_SCP_SDCA_INTMASK2, + SDW_SCP_SDCA_INTMASK_SDCA_8); + dev_dbg(&rt722->slave->dev, "in %s enable\n", __func__); + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_HDA_LEGACY_UNSOL_CTL, 0x016E); + /* set XU(et03h) & XU(et0Dh) to Not bypassed */ + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_XU03, + RT722_SDCA_CTL_SELECTED_MODE, 0), 0); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_XU0D, + RT722_SDCA_CTL_SELECTED_MODE, 0), 0); + /* trigger GE interrupt */ + rt722_sdca_index_update_bits(rt722, RT722_VENDOR_HDA_CTL, + RT722_GE_RELATED_CTL2, 0x4000, 0x4000); + } + mutex_unlock(&rt722->calibrate_mutex); +} + +static int rt722_sdca_set_jack_detect(struct snd_soc_component *component, + struct snd_soc_jack *hs_jack, void *data) +{ + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + int ret; + + rt722->hs_jack = hs_jack; + + ret = pm_runtime_resume_and_get(component->dev); + if (ret < 0) { + if (ret != -EACCES) { + dev_err(component->dev, "%s: failed to resume %d\n", __func__, ret); + return ret; + } + /* pm_runtime not enabled yet */ + dev_dbg(component->dev, "%s: skipping jack init for now\n", __func__); + return 0; + } + + rt722_sdca_jack_init(rt722); + + pm_runtime_mark_last_busy(component->dev); + pm_runtime_put_autosuspend(component->dev); + + return 0; +} + +/* For SDCA control DAC/ADC Gain */ +static int rt722_sdca_set_gain_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned int read_l, read_r, gain_l_val, gain_r_val; + unsigned int adc_vol_flag = 0, changed = 0; + unsigned int lvalue, rvalue; + const unsigned int interval_offset = 0xc0; + const unsigned int tendB = 0xa00; + + if (strstr(ucontrol->id.name, "FU1E Capture Volume") || + strstr(ucontrol->id.name, "FU0F Capture Volume")) + adc_vol_flag = 1; + + regmap_read(rt722->mbq_regmap, mc->reg, &lvalue); + regmap_read(rt722->mbq_regmap, mc->rreg, &rvalue); + + /* L Channel */ + gain_l_val = ucontrol->value.integer.value[0]; + if (gain_l_val > mc->max) + gain_l_val = mc->max; + + if (mc->shift == 8) /* boost gain */ + gain_l_val = gain_l_val * tendB; + else { + /* ADC/DAC gain */ + if (adc_vol_flag) + gain_l_val = 0x1e00 - ((mc->max - gain_l_val) * interval_offset); + else + gain_l_val = 0 - ((mc->max - gain_l_val) * interval_offset); + gain_l_val &= 0xffff; + } + + /* R Channel */ + gain_r_val = ucontrol->value.integer.value[1]; + if (gain_r_val > mc->max) + gain_r_val = mc->max; + + if (mc->shift == 8) /* boost gain */ + gain_r_val = gain_r_val * tendB; + else { + /* ADC/DAC gain */ + if (adc_vol_flag) + gain_r_val = 0x1e00 - ((mc->max - gain_r_val) * interval_offset); + else + gain_r_val = 0 - ((mc->max - gain_r_val) * interval_offset); + gain_r_val &= 0xffff; + } + + if (lvalue != gain_l_val || rvalue != gain_r_val) + changed = 1; + else + return 0; + + /* Lch*/ + regmap_write(rt722->mbq_regmap, mc->reg, gain_l_val); + + /* Rch */ + regmap_write(rt722->mbq_regmap, mc->rreg, gain_r_val); + + regmap_read(rt722->mbq_regmap, mc->reg, &read_l); + regmap_read(rt722->mbq_regmap, mc->rreg, &read_r); + if (read_r == gain_r_val && read_l == gain_l_val) + return 1; + + return -EIO; +} + +static int rt722_sdca_set_gain_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + unsigned int read_l, read_r, ctl_l = 0, ctl_r = 0; + unsigned int adc_vol_flag = 0; + const unsigned int interval_offset = 0xc0; + const unsigned int tendB = 0xa00; + + if (strstr(ucontrol->id.name, "FU1E Capture Volume") || + strstr(ucontrol->id.name, "FU0F Capture Volume")) + adc_vol_flag = 1; + + regmap_read(rt722->mbq_regmap, mc->reg, &read_l); + regmap_read(rt722->mbq_regmap, mc->rreg, &read_r); + + if (mc->shift == 8) /* boost gain */ + ctl_l = read_l / tendB; + else { + if (adc_vol_flag) + ctl_l = mc->max - (((0x1e00 - read_l) & 0xffff) / interval_offset); + else + ctl_l = mc->max - (((0 - read_l) & 0xffff) / interval_offset); + } + + if (read_l != read_r) { + if (mc->shift == 8) /* boost gain */ + ctl_r = read_r / tendB; + else { /* ADC/DAC gain */ + if (adc_vol_flag) + ctl_r = mc->max - (((0x1e00 - read_r) & 0xffff) / interval_offset); + else + ctl_r = mc->max - (((0 - read_r) & 0xffff) / interval_offset); + } + } else { + ctl_r = ctl_l; + } + + ucontrol->value.integer.value[0] = ctl_l; + ucontrol->value.integer.value[1] = ctl_r; + + return 0; +} + +static int rt722_sdca_set_fu1e_capture_ctl(struct rt722_sdca_priv *rt722) +{ + int err, i; + unsigned int ch_mute; + + for (i = 0; i < ARRAY_SIZE(rt722->fu1e_mixer_mute); i++) { + ch_mute = rt722->fu1e_dapm_mute || rt722->fu1e_mixer_mute[i]; + err = regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, + RT722_SDCA_CTL_FU_MUTE, CH_01) + i, ch_mute); + if (err < 0) + return err; + } + + return 0; +} + +static int rt722_sdca_fu1e_capture_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct rt722_sdca_dmic_kctrl_priv *p = + (struct rt722_sdca_dmic_kctrl_priv *)kcontrol->private_value; + unsigned int i; + + for (i = 0; i < p->count; i++) + ucontrol->value.integer.value[i] = !rt722->fu1e_mixer_mute[i]; + + return 0; +} + +static int rt722_sdca_fu1e_capture_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct rt722_sdca_dmic_kctrl_priv *p = + (struct rt722_sdca_dmic_kctrl_priv *)kcontrol->private_value; + int err, changed = 0, i; + + for (i = 0; i < p->count; i++) { + if (rt722->fu1e_mixer_mute[i] != !ucontrol->value.integer.value[i]) + changed = 1; + rt722->fu1e_mixer_mute[i] = !ucontrol->value.integer.value[i]; + } + + err = rt722_sdca_set_fu1e_capture_ctl(rt722); + if (err < 0) + return err; + + return changed; +} + +static int rt722_sdca_set_fu0f_capture_ctl(struct rt722_sdca_priv *rt722) +{ + int err; + unsigned int ch_l, ch_r; + + ch_l = (rt722->fu0f_dapm_mute || rt722->fu0f_mixer_l_mute) ? 0x01 : 0x00; + ch_r = (rt722->fu0f_dapm_mute || rt722->fu0f_mixer_r_mute) ? 0x01 : 0x00; + + err = regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, + RT722_SDCA_CTL_FU_MUTE, CH_L), ch_l); + if (err < 0) + return err; + + err = regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, + RT722_SDCA_CTL_FU_MUTE, CH_R), ch_r); + if (err < 0) + return err; + + return 0; +} + +static int rt722_sdca_fu0f_capture_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + + ucontrol->value.integer.value[0] = !rt722->fu0f_mixer_l_mute; + ucontrol->value.integer.value[1] = !rt722->fu0f_mixer_r_mute; + return 0; +} + +static int rt722_sdca_fu0f_capture_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + int err, changed = 0; + + if (rt722->fu0f_mixer_l_mute != !ucontrol->value.integer.value[0] || + rt722->fu0f_mixer_r_mute != !ucontrol->value.integer.value[1]) + changed = 1; + + rt722->fu0f_mixer_l_mute = !ucontrol->value.integer.value[0]; + rt722->fu0f_mixer_r_mute = !ucontrol->value.integer.value[1]; + err = rt722_sdca_set_fu0f_capture_ctl(rt722); + if (err < 0) + return err; + + return changed; +} + +static int rt722_sdca_fu_info(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + struct rt722_sdca_dmic_kctrl_priv *p = + (struct rt722_sdca_dmic_kctrl_priv *)kcontrol->private_value; + + if (p->max == 1) + uinfo->type = SNDRV_CTL_ELEM_TYPE_BOOLEAN; + else + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = p->count; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = p->max; + return 0; +} + +static int rt722_sdca_dmic_set_gain_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct rt722_sdca_dmic_kctrl_priv *p = + (struct rt722_sdca_dmic_kctrl_priv *)kcontrol->private_value; + unsigned int boost_step = 0x0a00; + unsigned int vol_max = 0x1e00; + unsigned int regvalue, ctl, i; + unsigned int adc_vol_flag = 0; + const unsigned int interval_offset = 0xc0; + + if (strstr(ucontrol->id.name, "FU1E Capture Volume")) + adc_vol_flag = 1; + + /* check all channels */ + for (i = 0; i < p->count; i++) { + regmap_read(rt722->mbq_regmap, p->reg_base + i, &regvalue); + + if (!adc_vol_flag) /* boost gain */ + ctl = regvalue / boost_step; + else { /* ADC gain */ + if (adc_vol_flag) + ctl = p->max - (((vol_max - regvalue) & 0xffff) / interval_offset); + else + ctl = p->max - (((0 - regvalue) & 0xffff) / interval_offset); + } + + ucontrol->value.integer.value[i] = ctl; + } + + return 0; +} + +static int rt722_sdca_dmic_set_gain_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt722_sdca_dmic_kctrl_priv *p = + (struct rt722_sdca_dmic_kctrl_priv *)kcontrol->private_value; + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned int boost_step = 0x0a00; + unsigned int vol_max = 0x1e00; + unsigned int gain_val[4]; + unsigned int i, adc_vol_flag = 0, changed = 0; + unsigned int regvalue[4]; + const unsigned int interval_offset = 0xc0; + int err; + + if (strstr(ucontrol->id.name, "FU1E Capture Volume")) + adc_vol_flag = 1; + + /* check all channels */ + for (i = 0; i < p->count; i++) { + regmap_read(rt722->mbq_regmap, p->reg_base + i, &regvalue[i]); + + gain_val[i] = ucontrol->value.integer.value[i]; + if (gain_val[i] > p->max) + gain_val[i] = p->max; + + if (!adc_vol_flag) /* boost gain */ + gain_val[i] = gain_val[i] * boost_step; + else { /* ADC gain */ + gain_val[i] = vol_max - ((p->max - gain_val[i]) * interval_offset); + gain_val[i] &= 0xffff; + } + + if (regvalue[i] != gain_val[i]) + changed = 1; + } + + if (!changed) + return 0; + + for (i = 0; i < p->count; i++) { + err = regmap_write(rt722->mbq_regmap, p->reg_base + i, gain_val[i]); + if (err < 0) + dev_err(&rt722->slave->dev, "%#08x can't be set\n", p->reg_base + i); + } + + return changed; +} + +#define RT722_SDCA_PR_VALUE(xreg_base, xcount, xmax, xinvert) \ + ((unsigned long)&(struct rt722_sdca_dmic_kctrl_priv) \ + {.reg_base = xreg_base, .count = xcount, .max = xmax, \ + .invert = xinvert}) + +#define RT722_SDCA_FU_CTRL(xname, reg_base, xmax, xinvert, xcount) \ +{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname), \ + .info = rt722_sdca_fu_info, \ + .get = rt722_sdca_fu1e_capture_get, \ + .put = rt722_sdca_fu1e_capture_put, \ + .private_value = RT722_SDCA_PR_VALUE(reg_base, xcount, xmax, xinvert)} + +#define RT722_SDCA_EXT_TLV(xname, reg_base, xhandler_get,\ + xhandler_put, xcount, xmax, tlv_array) \ +{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname), \ + .access = SNDRV_CTL_ELEM_ACCESS_TLV_READ | \ + SNDRV_CTL_ELEM_ACCESS_READWRITE, \ + .tlv.p = (tlv_array), \ + .info = rt722_sdca_fu_info, \ + .get = xhandler_get, .put = xhandler_put, \ + .private_value = RT722_SDCA_PR_VALUE(reg_base, xcount, xmax, 0) } + +static const DECLARE_TLV_DB_SCALE(out_vol_tlv, -6525, 75, 0); +static const DECLARE_TLV_DB_SCALE(mic_vol_tlv, -1725, 75, 0); +static const DECLARE_TLV_DB_SCALE(boost_vol_tlv, 0, 1000, 0); + +static const struct snd_kcontrol_new rt722_sdca_controls[] = { + /* Headphone playback settings */ + SOC_DOUBLE_R_EXT_TLV("FU05 Playback Volume", + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_VOLUME, CH_L), + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_VOLUME, CH_R), 0, 0x57, 0, + rt722_sdca_set_gain_get, rt722_sdca_set_gain_put, out_vol_tlv), + /* Headset mic capture settings */ + SOC_DOUBLE_EXT("FU0F Capture Switch", SND_SOC_NOPM, 0, 1, 1, 0, + rt722_sdca_fu0f_capture_get, rt722_sdca_fu0f_capture_put), + SOC_DOUBLE_R_EXT_TLV("FU0F Capture Volume", + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, + RT722_SDCA_CTL_FU_VOLUME, CH_L), + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU0F, + RT722_SDCA_CTL_FU_VOLUME, CH_R), 0, 0x3f, 0, + rt722_sdca_set_gain_get, rt722_sdca_set_gain_put, mic_vol_tlv), + SOC_DOUBLE_R_EXT_TLV("FU33 Boost Volume", + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, + RT722_SDCA_CTL_FU_CH_GAIN, CH_L), + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PLATFORM_FU44, + RT722_SDCA_CTL_FU_CH_GAIN, CH_R), 8, 3, 0, + rt722_sdca_set_gain_get, rt722_sdca_set_gain_put, boost_vol_tlv), + /* AMP playback settings */ + SOC_DOUBLE_R_EXT_TLV("FU06 Playback Volume", + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_VOLUME, CH_L), + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_VOLUME, CH_R), 0, 0x57, 0, + rt722_sdca_set_gain_get, rt722_sdca_set_gain_put, out_vol_tlv), + /* DMIC capture settings */ + RT722_SDCA_FU_CTRL("FU1E Capture Switch", + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, + RT722_SDCA_CTL_FU_MUTE, CH_01), 1, 1, 4), + RT722_SDCA_EXT_TLV("FU1E Capture Volume", + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_USER_FU1E, + RT722_SDCA_CTL_FU_VOLUME, CH_01), + rt722_sdca_dmic_set_gain_get, rt722_sdca_dmic_set_gain_put, + 4, 0x3f, mic_vol_tlv), + RT722_SDCA_EXT_TLV("FU15 Boost Volume", + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15, + RT722_SDCA_CTL_FU_CH_GAIN, CH_01), + rt722_sdca_dmic_set_gain_get, rt722_sdca_dmic_set_gain_put, + 4, 3, boost_vol_tlv), +}; + +static int rt722_sdca_adc_mux_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = + snd_soc_dapm_kcontrol_component(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned int val = 0, mask_sft; + + if (strstr(ucontrol->id.name, "ADC 22 Mux")) + mask_sft = 12; + else if (strstr(ucontrol->id.name, "ADC 24 Mux")) + mask_sft = 4; + else if (strstr(ucontrol->id.name, "ADC 25 Mux")) + mask_sft = 0; + else + return -EINVAL; + + rt722_sdca_index_read(rt722, RT722_VENDOR_HDA_CTL, + RT722_HDA_LEGACY_MUX_CTL0, &val); + + ucontrol->value.enumerated.item[0] = (val >> mask_sft) & 0x7; + + return 0; +} + +static int rt722_sdca_adc_mux_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = + snd_soc_dapm_kcontrol_component(kcontrol); + struct snd_soc_dapm_context *dapm = + snd_soc_dapm_kcontrol_dapm(kcontrol); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct soc_enum *e = (struct soc_enum *)kcontrol->private_value; + unsigned int *item = ucontrol->value.enumerated.item; + unsigned int val, val2 = 0, change, mask_sft; + + if (item[0] >= e->items) + return -EINVAL; + + if (strstr(ucontrol->id.name, "ADC 22 Mux")) + mask_sft = 12; + else if (strstr(ucontrol->id.name, "ADC 24 Mux")) + mask_sft = 4; + else if (strstr(ucontrol->id.name, "ADC 25 Mux")) + mask_sft = 0; + else + return -EINVAL; + + val = snd_soc_enum_item_to_val(e, item[0]) << e->shift_l; + + rt722_sdca_index_read(rt722, RT722_VENDOR_HDA_CTL, + RT722_HDA_LEGACY_MUX_CTL0, &val2); + val2 = (0x7 << mask_sft) & val2; + + if (val == val2) + change = 0; + else + change = 1; + + if (change) + rt722_sdca_index_update_bits(rt722, RT722_VENDOR_HDA_CTL, + RT722_HDA_LEGACY_MUX_CTL0, 0x7 << mask_sft, + val << mask_sft); + + snd_soc_dapm_mux_update_power(dapm, kcontrol, + item[0], e, NULL); + + return change; +} + +static const char * const adc22_mux_text[] = { + "MIC2", + "LINE1", + "LINE2", +}; + +static const char * const adc07_10_mux_text[] = { + "DMIC1", + "DMIC2", +}; + +static SOC_ENUM_SINGLE_DECL( + rt722_adc22_enum, SND_SOC_NOPM, 0, adc22_mux_text); + +static SOC_ENUM_SINGLE_DECL( + rt722_adc24_enum, SND_SOC_NOPM, 0, adc07_10_mux_text); + +static SOC_ENUM_SINGLE_DECL( + rt722_adc25_enum, SND_SOC_NOPM, 0, adc07_10_mux_text); + +static const struct snd_kcontrol_new rt722_sdca_adc22_mux = + SOC_DAPM_ENUM_EXT("ADC 22 Mux", rt722_adc22_enum, + rt722_sdca_adc_mux_get, rt722_sdca_adc_mux_put); + +static const struct snd_kcontrol_new rt722_sdca_adc24_mux = + SOC_DAPM_ENUM_EXT("ADC 24 Mux", rt722_adc24_enum, + rt722_sdca_adc_mux_get, rt722_sdca_adc_mux_put); + +static const struct snd_kcontrol_new rt722_sdca_adc25_mux = + SOC_DAPM_ENUM_EXT("ADC 25 Mux", rt722_adc25_enum, + rt722_sdca_adc_mux_get, rt722_sdca_adc_mux_put); + +static int rt722_sdca_fu42_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char unmute = 0x0, mute = 0x1; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_MUTE, CH_L), unmute); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_MUTE, CH_R), unmute); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_MUTE, CH_L), mute); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_USER_FU05, + RT722_SDCA_CTL_FU_MUTE, CH_R), mute); + break; + } + return 0; +} + +static int rt722_sdca_fu21_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char unmute = 0x0, mute = 0x1; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_MUTE, CH_L), unmute); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_MUTE, CH_R), unmute); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_MUTE, CH_L), mute); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_USER_FU06, + RT722_SDCA_CTL_FU_MUTE, CH_R), mute); + break; + } + return 0; +} + +static int rt722_sdca_fu113_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + rt722->fu1e_dapm_mute = false; + rt722_sdca_set_fu1e_capture_ctl(rt722); + break; + case SND_SOC_DAPM_PRE_PMD: + rt722->fu1e_dapm_mute = true; + rt722_sdca_set_fu1e_capture_ctl(rt722); + break; + } + return 0; +} + +static int rt722_sdca_fu36_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + rt722->fu0f_dapm_mute = false; + rt722_sdca_set_fu0f_capture_ctl(rt722); + break; + case SND_SOC_DAPM_PRE_PMD: + rt722->fu0f_dapm_mute = true; + rt722_sdca_set_fu0f_capture_ctl(rt722); + break; + } + return 0; +} + +static int rt722_sdca_pde47_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char ps0 = 0x0, ps3 = 0x3; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE40, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE40, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps3); + break; + } + return 0; +} + +static int rt722_sdca_pde23_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char ps0 = 0x0, ps3 = 0x3; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_PDE23, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_PDE23, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps3); + break; + } + return 0; +} + +static int rt722_sdca_pde11_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char ps0 = 0x0, ps3 = 0x3; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_PDE2A, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_PDE2A, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps3); + break; + } + return 0; +} + +static int rt722_sdca_pde12_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + unsigned char ps0 = 0x0, ps3 = 0x3; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE12, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_PDE12, + RT722_SDCA_CTL_REQ_POWER_STATE, 0), ps3); + break; + } + return 0; +} + +static const struct snd_soc_dapm_widget rt722_sdca_dapm_widgets[] = { + SND_SOC_DAPM_OUTPUT("HP"), + SND_SOC_DAPM_OUTPUT("SPK"), + SND_SOC_DAPM_INPUT("MIC2"), + SND_SOC_DAPM_INPUT("LINE1"), + SND_SOC_DAPM_INPUT("LINE2"), + SND_SOC_DAPM_INPUT("DMIC1_2"), + SND_SOC_DAPM_INPUT("DMIC3_4"), + + SND_SOC_DAPM_SUPPLY("PDE 23", SND_SOC_NOPM, 0, 0, + rt722_sdca_pde23_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_SUPPLY("PDE 47", SND_SOC_NOPM, 0, 0, + rt722_sdca_pde47_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_SUPPLY("PDE 11", SND_SOC_NOPM, 0, 0, + rt722_sdca_pde11_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_SUPPLY("PDE 12", SND_SOC_NOPM, 0, 0, + rt722_sdca_pde12_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + + SND_SOC_DAPM_DAC_E("FU 21", NULL, SND_SOC_NOPM, 0, 0, + rt722_sdca_fu21_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_DAC_E("FU 42", NULL, SND_SOC_NOPM, 0, 0, + rt722_sdca_fu42_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_ADC_E("FU 36", NULL, SND_SOC_NOPM, 0, 0, + rt722_sdca_fu36_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_ADC_E("FU 113", NULL, SND_SOC_NOPM, 0, 0, + rt722_sdca_fu113_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_MUX("ADC 22 Mux", SND_SOC_NOPM, 0, 0, + &rt722_sdca_adc22_mux), + SND_SOC_DAPM_MUX("ADC 24 Mux", SND_SOC_NOPM, 0, 0, + &rt722_sdca_adc24_mux), + SND_SOC_DAPM_MUX("ADC 25 Mux", SND_SOC_NOPM, 0, 0, + &rt722_sdca_adc25_mux), + + SND_SOC_DAPM_AIF_IN("DP1RX", "DP1 Headphone Playback", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_OUT("DP2TX", "DP2 Headset Capture", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_IN("DP3RX", "DP3 Speaker Playback", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_OUT("DP6TX", "DP6 DMic Capture", 0, SND_SOC_NOPM, 0, 0), +}; + +static const struct snd_soc_dapm_route rt722_sdca_audio_map[] = { + {"FU 42", NULL, "DP1RX"}, + {"FU 21", NULL, "DP3RX"}, + + {"ADC 22 Mux", "MIC2", "MIC2"}, + {"ADC 22 Mux", "LINE1", "LINE1"}, + {"ADC 22 Mux", "LINE2", "LINE2"}, + {"ADC 24 Mux", "DMIC1", "DMIC1_2"}, + {"ADC 24 Mux", "DMIC2", "DMIC3_4"}, + {"ADC 25 Mux", "DMIC1", "DMIC1_2"}, + {"ADC 25 Mux", "DMIC2", "DMIC3_4"}, + {"FU 36", NULL, "PDE 12"}, + {"FU 36", NULL, "ADC 22 Mux"}, + {"FU 113", NULL, "PDE 11"}, + {"FU 113", NULL, "ADC 24 Mux"}, + {"FU 113", NULL, "ADC 25 Mux"}, + {"DP2TX", NULL, "FU 36"}, + {"DP6TX", NULL, "FU 113"}, + + {"HP", NULL, "PDE 47"}, + {"HP", NULL, "FU 42"}, + {"SPK", NULL, "PDE 23"}, + {"SPK", NULL, "FU 21"}, +}; + +static int rt722_sdca_parse_dt(struct rt722_sdca_priv *rt722, struct device *dev) +{ + device_property_read_u32(dev, "realtek,jd-src", &rt722->jd_src); + + return 0; +} + +static int rt722_sdca_probe(struct snd_soc_component *component) +{ + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + int ret; + + rt722_sdca_parse_dt(rt722, &rt722->slave->dev); + rt722->component = component; + + ret = pm_runtime_resume(component->dev); + if (ret < 0 && ret != -EACCES) + return ret; + + return 0; +} + +static const struct snd_soc_component_driver soc_sdca_dev_rt722 = { + .probe = rt722_sdca_probe, + .controls = rt722_sdca_controls, + .num_controls = ARRAY_SIZE(rt722_sdca_controls), + .dapm_widgets = rt722_sdca_dapm_widgets, + .num_dapm_widgets = ARRAY_SIZE(rt722_sdca_dapm_widgets), + .dapm_routes = rt722_sdca_audio_map, + .num_dapm_routes = ARRAY_SIZE(rt722_sdca_audio_map), + .set_jack = rt722_sdca_set_jack_detect, + .endianness = 1, +}; + +static int rt722_sdca_set_sdw_stream(struct snd_soc_dai *dai, void *sdw_stream, + int direction) +{ + snd_soc_dai_dma_data_set(dai, direction, sdw_stream); + + return 0; +} + +static void rt722_sdca_shutdown(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + snd_soc_dai_set_dma_data(dai, substream, NULL); +} + +static int rt722_sdca_pcm_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_component *component = dai->component; + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct sdw_stream_config stream_config; + struct sdw_port_config port_config; + enum sdw_data_direction direction; + struct sdw_stream_runtime *sdw_stream; + int retval, port, num_channels; + unsigned int sampling_rate; + + dev_dbg(dai->dev, "%s %s", __func__, dai->name); + sdw_stream = snd_soc_dai_get_dma_data(dai, substream); + + if (!sdw_stream) + return -EINVAL; + + if (!rt722->slave) + return -EINVAL; + + /* + * RT722_AIF1 with port = 1 for headphone playback + * RT722_AIF1 with port = 2 for headset-mic capture + * RT722_AIF2 with port = 3 for speaker playback + * RT722_AIF2 with port = 6 for digital-mic capture + */ + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) { + direction = SDW_DATA_DIR_RX; + if (dai->id == RT722_AIF1) + port = 1; + else if (dai->id == RT722_AIF2) + port = 3; + else + return -EINVAL; + } else { + direction = SDW_DATA_DIR_TX; + if (dai->id == RT722_AIF1) + port = 2; + else if (dai->id == RT722_AIF2) + port = 6; + else + return -EINVAL; + } + stream_config.frame_rate = params_rate(params); + stream_config.ch_count = params_channels(params); + stream_config.bps = snd_pcm_format_width(params_format(params)); + stream_config.direction = direction; + + num_channels = params_channels(params); + port_config.ch_mask = GENMASK(num_channels - 1, 0); + port_config.num = port; + + retval = sdw_stream_add_slave(rt722->slave, &stream_config, + &port_config, 1, sdw_stream); + if (retval) { + dev_err(dai->dev, "Unable to configure port\n"); + return retval; + } + + if (params_channels(params) > 16) { + dev_err(component->dev, "Unsupported channels %d\n", + params_channels(params)); + return -EINVAL; + } + + /* sampling rate configuration */ + switch (params_rate(params)) { + case 44100: + sampling_rate = RT722_SDCA_RATE_44100HZ; + break; + case 48000: + sampling_rate = RT722_SDCA_RATE_48000HZ; + break; + case 96000: + sampling_rate = RT722_SDCA_RATE_96000HZ; + break; + case 192000: + sampling_rate = RT722_SDCA_RATE_192000HZ; + break; + default: + dev_err(component->dev, "Rate %d is not supported\n", + params_rate(params)); + return -EINVAL; + } + + /* set sampling frequency */ + if (dai->id == RT722_AIF1) { + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_CS01, + RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), sampling_rate); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT722_SDCA_ENT_CS11, + RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), sampling_rate); + } + + if (dai->id == RT722_AIF2) { + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_CS1F, + RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), sampling_rate); + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_CS31, + RT722_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), sampling_rate); + } + + return 0; +} + +static int rt722_sdca_pcm_hw_free(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct snd_soc_component *component = dai->component; + struct rt722_sdca_priv *rt722 = snd_soc_component_get_drvdata(component); + struct sdw_stream_runtime *sdw_stream = + snd_soc_dai_get_dma_data(dai, substream); + + if (!rt722->slave) + return -EINVAL; + + sdw_stream_remove_slave(rt722->slave, sdw_stream); + return 0; +} + +#define RT722_STEREO_RATES (SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000 | \ + SNDRV_PCM_RATE_96000 | SNDRV_PCM_RATE_192000) +#define RT722_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE | \ + SNDRV_PCM_FMTBIT_S24_LE) + +static const struct snd_soc_dai_ops rt722_sdca_ops = { + .hw_params = rt722_sdca_pcm_hw_params, + .hw_free = rt722_sdca_pcm_hw_free, + .set_stream = rt722_sdca_set_sdw_stream, + .shutdown = rt722_sdca_shutdown, +}; + +static struct snd_soc_dai_driver rt722_sdca_dai[] = { + { + .name = "rt722-sdca-aif1", + .id = RT722_AIF1, + .playback = { + .stream_name = "DP1 Headphone Playback", + .channels_min = 1, + .channels_max = 2, + .rates = RT722_STEREO_RATES, + .formats = RT722_FORMATS, + }, + .capture = { + .stream_name = "DP2 Headset Capture", + .channels_min = 1, + .channels_max = 2, + .rates = RT722_STEREO_RATES, + .formats = RT722_FORMATS, + }, + .ops = &rt722_sdca_ops, + }, + { + .name = "rt722-sdca-aif2", + .id = RT722_AIF2, + .playback = { + .stream_name = "DP3 Speaker Playback", + .channels_min = 1, + .channels_max = 2, + .rates = RT722_STEREO_RATES, + .formats = RT722_FORMATS, + }, + .capture = { + .stream_name = "DP6 DMic Capture", + .channels_min = 1, + .channels_max = 2, + .rates = RT722_STEREO_RATES, + .formats = RT722_FORMATS, + }, + .ops = &rt722_sdca_ops, + } +}; + +int rt722_sdca_init(struct device *dev, struct regmap *regmap, + struct regmap *mbq_regmap, struct sdw_slave *slave) +{ + struct rt722_sdca_priv *rt722; + + rt722 = devm_kzalloc(dev, sizeof(*rt722), GFP_KERNEL); + if (!rt722) + return -ENOMEM; + + dev_set_drvdata(dev, rt722); + rt722->slave = slave; + rt722->regmap = regmap; + rt722->mbq_regmap = mbq_regmap; + + mutex_init(&rt722->calibrate_mutex); + mutex_init(&rt722->disable_irq_lock); + + INIT_DELAYED_WORK(&rt722->jack_detect_work, rt722_sdca_jack_detect_handler); + INIT_DELAYED_WORK(&rt722->jack_btn_check_work, rt722_sdca_btn_check_handler); + + /* + * Mark hw_init to false + * HW init will be performed when device reports present + */ + rt722->hw_init = false; + rt722->first_hw_init = false; + rt722->fu1e_dapm_mute = true; + rt722->fu0f_dapm_mute = true; + rt722->fu0f_mixer_l_mute = rt722->fu0f_mixer_r_mute = true; + rt722->fu1e_mixer_mute[0] = rt722->fu1e_mixer_mute[1] = + rt722->fu1e_mixer_mute[2] = rt722->fu1e_mixer_mute[3] = true; + + return devm_snd_soc_register_component(dev, + &soc_sdca_dev_rt722, rt722_sdca_dai, ARRAY_SIZE(rt722_sdca_dai)); +} + +static void rt722_sdca_dmic_preset(struct rt722_sdca_priv *rt722) +{ + /* Set AD07 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_ADC0A_08_PDE_FLOAT_CTL, 0x2a29); + /* Set AD10 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_ADC10_PDE_FLOAT_CTL, 0x2a00); + /* Set DMIC1/DMIC2 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_DMIC1_2_PDE_FLOAT_CTL, 0x2a2a); + /* Set DMIC2 IT entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_DMIC_ENT_FLOAT_CTL, 0x2626); + /* Set AD10 FU entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_ADC_ENT_FLOAT_CTL, 0x1e00); + /* Set DMIC2 FU entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_DMIC_GAIN_ENT_FLOAT_CTL0, 0x1515); + /* Set AD10 FU channel floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_ADC_VOL_CH_FLOAT_CTL, 0x0304); + /* Set DMIC2 FU channel floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_DMIC_GAIN_ENT_FLOAT_CTL2, 0x0304); + /* vf71f_r12_07_06 and vf71f_r13_07_06 = 2’b00 */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, + RT722_HDA_LEGACY_CONFIG_CTL0, 0x0000); + /* Enable vf707_r12_05/vf707_r13_05 */ + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_IT26, + RT722_SDCA_CTL_VENDOR_DEF, 0), 0x01); + /* Fine tune PDE2A latency */ + regmap_write(rt722->regmap, 0x2f5c, 0x25); +} + +static void rt722_sdca_amp_preset(struct rt722_sdca_priv *rt722) +{ + /* Set DVQ=01 */ + rt722_sdca_index_write(rt722, RT722_VENDOR_REG, RT722_CLSD_CTRL6, + 0xc215); + /* Reset dc_cal_top */ + rt722_sdca_index_write(rt722, RT722_VENDOR_CALI, RT722_DC_CALIB_CTRL, + 0x702c); + /* W1C Trigger Calibration */ + rt722_sdca_index_write(rt722, RT722_VENDOR_CALI, RT722_DC_CALIB_CTRL, + 0xf02d); + /* Set DAC02/ClassD power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_AMP_PDE_FLOAT_CTL, + 0x2323); + /* Set EAPD high */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_EAPD_CTL, + 0x0002); + /* Enable vf707_r14 */ + regmap_write(rt722->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT722_SDCA_ENT_OT23, + RT722_SDCA_CTL_VENDOR_DEF, CH_08), 0x04); +} + +static void rt722_sdca_jack_preset(struct rt722_sdca_priv *rt722) +{ + int loop_check, chk_cnt = 100, ret; + unsigned int calib_status = 0; + + /* Read eFuse */ + rt722_sdca_index_write(rt722, RT722_VENDOR_SPK_EFUSE, RT722_DC_CALIB_CTRL, + 0x4808); + /* Button A, B, C, D bypass mode */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_UMP_HID_CTL4, + 0xcf00); + /* HID1 slot enable */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_UMP_HID_CTL5, + 0x000f); + /* Report ID for HID1 */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_UMP_HID_CTL0, + 0x1100); + /* OSC/OOC for slot 2, 3 */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_UMP_HID_CTL7, + 0x0c12); + /* Set JD de-bounce clock control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_REG, RT722_JD_CTRL1, + 0x7002); + /* Set DVQ=01 */ + rt722_sdca_index_write(rt722, RT722_VENDOR_REG, RT722_CLSD_CTRL6, + 0xc215); + /* FSM switch to calibration manual mode */ + rt722_sdca_index_write(rt722, RT722_VENDOR_REG, RT722_FSM_CTL, + 0x4100); + /* W1C Trigger DC calibration (HP) */ + rt722_sdca_index_write(rt722, RT722_VENDOR_CALI, RT722_DAC_DC_CALI_CTL3, + 0x008d); + /* check HP calibration FSM status */ + for (loop_check = 0; loop_check < chk_cnt; loop_check++) { + ret = rt722_sdca_index_read(rt722, RT722_VENDOR_CALI, + RT722_DAC_DC_CALI_CTL3, &calib_status); + if (ret < 0 || loop_check == chk_cnt) + dev_dbg(&rt722->slave->dev, "calibration failed!, ret=%d\n", ret); + if ((calib_status & 0x0040) == 0x0) + break; + } + /* Release HP-JD, EN_CBJ_TIE_GL/R open, en_osw gating auto done bit */ + rt722_sdca_index_write(rt722, RT722_VENDOR_REG, RT722_DIGITAL_MISC_CTRL4, + 0x0010); + /* Set ADC09 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_ADC0A_08_PDE_FLOAT_CTL, + 0x2a12); + /* Set MIC2 and LINE1 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_MIC2_LINE2_PDE_FLOAT_CTL, + 0x3429); + /* Set ET41h and LINE2 power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_ET41_LINE2_PDE_FLOAT_CTL, + 0x4112); + /* Set DAC03 and HP power entity floating control */ + rt722_sdca_index_write(rt722, RT722_VENDOR_HDA_CTL, RT722_DAC03_HP_PDE_FLOAT_CTL, + 0x4040); + /* Fine tune PDE40 latency */ + regmap_write(rt722->regmap, 0x2f58, 0x07); +} + +int rt722_sdca_io_init(struct device *dev, struct sdw_slave *slave) +{ + struct rt722_sdca_priv *rt722 = dev_get_drvdata(dev); + + rt722->disable_irq = false; + + if (rt722->hw_init) + return 0; + + if (rt722->first_hw_init) { + regcache_cache_only(rt722->regmap, false); + regcache_cache_bypass(rt722->regmap, true); + regcache_cache_only(rt722->mbq_regmap, false); + regcache_cache_bypass(rt722->mbq_regmap, true); + } else { + /* + * PM runtime is only enabled when a Slave reports as Attached + */ + + /* set autosuspend parameters */ + pm_runtime_set_autosuspend_delay(&slave->dev, 3000); + pm_runtime_use_autosuspend(&slave->dev); + + /* update count of parent 'active' children */ + pm_runtime_set_active(&slave->dev); + + /* make sure the device does not suspend immediately */ + pm_runtime_mark_last_busy(&slave->dev); + + pm_runtime_enable(&slave->dev); + } + + pm_runtime_get_noresume(&slave->dev); + + rt722_sdca_dmic_preset(rt722); + rt722_sdca_amp_preset(rt722); + rt722_sdca_jack_preset(rt722); + + if (rt722->first_hw_init) { + regcache_cache_bypass(rt722->regmap, false); + regcache_mark_dirty(rt722->regmap); + regcache_cache_bypass(rt722->mbq_regmap, false); + regcache_mark_dirty(rt722->mbq_regmap); + } else + rt722->first_hw_init = true; + + /* Mark Slave initialization complete */ + rt722->hw_init = true; + + pm_runtime_mark_last_busy(&slave->dev); + pm_runtime_put_autosuspend(&slave->dev); + + dev_dbg(&slave->dev, "%s hw_init complete\n", __func__); + return 0; +} + +MODULE_DESCRIPTION("ASoC RT722 SDCA SDW driver"); +MODULE_AUTHOR("Jack Yu <jack.yu(a)realtek.com>"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/rt722-sdca.h b/sound/soc/codecs/rt722-sdca.h new file mode 100644 index 000000000000..b80b901a0636 --- /dev/null +++ b/sound/soc/codecs/rt722-sdca.h @@ -0,0 +1,237 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * rt722-sdca.h -- RT722 SDCA ALSA SoC audio driver header + * + * Copyright(c) 2023 Realtek Semiconductor Corp. + */ + +#ifndef __RT722_H__ +#define __RT722_H__ + +#include <linux/pm.h> +#include <linux/regmap.h> +#include <linux/soundwire/sdw.h> +#include <linux/soundwire/sdw_type.h> +#include <sound/soc.h> +#include <linux/workqueue.h> + +struct rt722_sdca_priv { + struct regmap *regmap; + struct regmap *mbq_regmap; + struct snd_soc_component *component; + struct sdw_slave *slave; + enum sdw_slave_status status; + struct sdw_bus_params params; + bool hw_init; + bool first_hw_init; + struct mutex calibrate_mutex; + struct mutex disable_irq_lock; + bool disable_irq; + /* For Headset jack & Headphone */ + unsigned int scp_sdca_stat1; + unsigned int scp_sdca_stat2; + struct snd_soc_jack *hs_jack; + struct delayed_work jack_detect_work; + struct delayed_work jack_btn_check_work; + int jack_type; + int jd_src; + bool fu0f_dapm_mute; + bool fu0f_mixer_l_mute; + bool fu0f_mixer_r_mute; + /* For DMIC */ + bool fu1e_dapm_mute; + bool fu1e_mixer_mute[4]; +}; + +struct rt722_sdca_dmic_kctrl_priv { + unsigned int reg_base; + unsigned int count; + unsigned int max; + unsigned int invert; +}; + +/* NID */ +#define RT722_VENDOR_REG 0x20 +#define RT722_VENDOR_CALI 0x58 +#define RT722_VENDOR_SPK_EFUSE 0x5c +#define RT722_VENDOR_IMS_DRE 0x5b +#define RT722_VENDOR_ANALOG_CTL 0x5f +#define RT722_VENDOR_HDA_CTL 0x61 + +/* Index (NID:20h) */ +#define RT722_JD_PRODUCT_NUM 0x00 +#define RT722_ANALOG_BIAS_CTL3 0x04 +#define RT722_JD_CTRL1 0x09 +#define RT722_LDO2_3_CTL1 0x0e +#define RT722_LDO1_CTL 0x1a +#define RT722_HP_JD_CTRL 0x24 +#define RT722_CLSD_CTRL6 0x3c +#define RT722_COMBO_JACK_AUTO_CTL1 0x45 +#define RT722_COMBO_JACK_AUTO_CTL2 0x46 +#define RT722_COMBO_JACK_AUTO_CTL3 0x47 +#define RT722_DIGITAL_MISC_CTRL4 0x4a +#define RT722_FSM_CTL 0x67 +#define RT722_SDCA_INTR_REC 0x82 +#define RT722_SW_CONFIG1 0x8a +#define RT722_SW_CONFIG2 0x8b + +/* Index (NID:58h) */ +#define RT722_DAC_DC_CALI_CTL0 0x00 +#define RT722_DAC_DC_CALI_CTL1 0x01 +#define RT722_DAC_DC_CALI_CTL2 0x02 +#define RT722_DAC_DC_CALI_CTL3 0x03 + +/* Index (NID:59h) */ +#define RT722_ULTRA_SOUND_DETECTOR6 0x1e + +/* Index (NID:5bh) */ +#define RT722_IMS_DIGITAL_CTL1 0x00 +#define RT722_IMS_DIGITAL_CTL5 0x05 +#define RT722_HP_DETECT_RLDET_CTL1 0x29 +#define RT722_HP_DETECT_RLDET_CTL2 0x2a + +/* Index (NID:5fh) */ +#define RT722_MISC_POWER_CTL0 0x00 +#define RT722_MISC_POWER_CTL7 0x08 + +/* Index (NID:61h) */ +#define RT722_HDA_LEGACY_MUX_CTL0 0x00 +#define RT722_HDA_LEGACY_UNSOL_CTL 0x03 +#define RT722_HDA_LEGACY_CONFIG_CTL0 0x06 +#define RT722_HDA_LEGACY_RESET_CTL 0x08 +#define RT722_HDA_LEGACY_GPIO_WAKE_EN_CTL 0x0e +#define RT722_DMIC_ENT_FLOAT_CTL 0x10 +#define RT722_DMIC_GAIN_ENT_FLOAT_CTL0 0x11 +#define RT722_DMIC_GAIN_ENT_FLOAT_CTL2 0x13 +#define RT722_ADC_ENT_FLOAT_CTL 0x15 +#define RT722_ADC_VOL_CH_FLOAT_CTL 0x17 +#define RT722_ADC_SAMPLE_RATE_FLOAT 0x18 +#define RT722_DAC03_HP_PDE_FLOAT_CTL 0x22 +#define RT722_MIC2_LINE2_PDE_FLOAT_CTL 0x23 +#define RT722_ET41_LINE2_PDE_FLOAT_CTL 0x24 +#define RT722_ADC0A_08_PDE_FLOAT_CTL 0x25 +#define RT722_ADC10_PDE_FLOAT_CTL 0x26 +#define RT722_DMIC1_2_PDE_FLOAT_CTL 0x28 +#define RT722_AMP_PDE_FLOAT_CTL 0x29 +#define RT722_I2S_IN_OUT_PDE_FLOAT_CTL 0x2f +#define RT722_GE_RELATED_CTL1 0x45 +#define RT722_GE_RELATED_CTL2 0x46 +#define RT722_MIXER_CTL0 0x52 +#define RT722_MIXER_CTL1 0x53 +#define RT722_EAPD_CTL 0x55 +#define RT722_UMP_HID_CTL0 0x60 +#define RT722_UMP_HID_CTL1 0x61 +#define RT722_UMP_HID_CTL2 0x62 +#define RT722_UMP_HID_CTL3 0x63 +#define RT722_UMP_HID_CTL4 0x64 +#define RT722_UMP_HID_CTL5 0x65 +#define RT722_UMP_HID_CTL6 0x66 +#define RT722_UMP_HID_CTL7 0x67 +#define RT722_UMP_HID_CTL8 0x68 + +/* Parameter & Verb control 01 (0x1a)(NID:20h) */ +#define RT722_HIDDEN_REG_SW_RESET (0x1 << 14) + +/* combo jack auto switch control 2 (0x46)(NID:20h) */ +#define RT722_COMBOJACK_AUTO_DET_STATUS (0x1 << 11) +#define RT722_COMBOJACK_AUTO_DET_TRS (0x1 << 10) +#define RT722_COMBOJACK_AUTO_DET_CTIA (0x1 << 9) +#define RT722_COMBOJACK_AUTO_DET_OMTP (0x1 << 8) + +/* DAC calibration control (0x00)(NID:58h) */ +#define RT722_DC_CALIB_CTRL (0x1 << 16) +/* DAC DC offset calibration control-1 (0x01)(NID:58h) */ +#define RT722_PDM_DC_CALIB_STATUS (0x1 << 15) + +#define RT722_EAPD_HIGH 0x2 +#define RT722_EAPD_LOW 0x0 + +/* Buffer address for HID */ +#define RT722_BUF_ADDR_HID1 0x44030000 +#define RT722_BUF_ADDR_HID2 0x44030020 + +/* RT722 SDCA Control - function number */ +#define FUNC_NUM_JACK_CODEC 0x01 +#define FUNC_NUM_MIC_ARRAY 0x02 +#define FUNC_NUM_HID 0x03 +#define FUNC_NUM_AMP 0x04 + +/* RT722 SDCA entity */ +#define RT722_SDCA_ENT_HID01 0x01 +#define RT722_SDCA_ENT_GE49 0x49 +#define RT722_SDCA_ENT_USER_FU05 0x05 +#define RT722_SDCA_ENT_USER_FU06 0x06 +#define RT722_SDCA_ENT_USER_FU0F 0x0f +#define RT722_SDCA_ENT_USER_FU10 0x19 +#define RT722_SDCA_ENT_USER_FU1E 0x1e +#define RT722_SDCA_ENT_FU15 0x15 +#define RT722_SDCA_ENT_PDE23 0x23 +#define RT722_SDCA_ENT_PDE40 0x40 +#define RT722_SDCA_ENT_PDE11 0x11 +#define RT722_SDCA_ENT_PDE12 0x12 +#define RT722_SDCA_ENT_PDE2A 0x2a +#define RT722_SDCA_ENT_CS01 0x01 +#define RT722_SDCA_ENT_CS11 0x11 +#define RT722_SDCA_ENT_CS1F 0x1f +#define RT722_SDCA_ENT_CS1C 0x1c +#define RT722_SDCA_ENT_CS31 0x31 +#define RT722_SDCA_ENT_OT23 0x42 +#define RT722_SDCA_ENT_IT26 0x26 +#define RT722_SDCA_ENT_IT09 0x09 +#define RT722_SDCA_ENT_PLATFORM_FU15 0x15 +#define RT722_SDCA_ENT_PLATFORM_FU44 0x44 +#define RT722_SDCA_ENT_XU03 0x03 +#define RT722_SDCA_ENT_XU0D 0x0d + +/* RT722 SDCA control */ +#define RT722_SDCA_CTL_SAMPLE_FREQ_INDEX 0x10 +#define RT722_SDCA_CTL_FU_MUTE 0x01 +#define RT722_SDCA_CTL_FU_VOLUME 0x02 +#define RT722_SDCA_CTL_HIDTX_CURRENT_OWNER 0x10 +#define RT722_SDCA_CTL_HIDTX_SET_OWNER_TO_DEVICE 0x11 +#define RT722_SDCA_CTL_HIDTX_MESSAGE_OFFSET 0x12 +#define RT722_SDCA_CTL_HIDTX_MESSAGE_LENGTH 0x13 +#define RT722_SDCA_CTL_SELECTED_MODE 0x01 +#define RT722_SDCA_CTL_DETECTED_MODE 0x02 +#define RT722_SDCA_CTL_REQ_POWER_STATE 0x01 +#define RT722_SDCA_CTL_VENDOR_DEF 0x30 +#define RT722_SDCA_CTL_FU_CH_GAIN 0x0b + +/* RT722 SDCA channel */ +#define CH_L 0x01 +#define CH_R 0x02 +#define CH_01 0x01 +#define CH_02 0x02 +#define CH_03 0x03 +#define CH_04 0x04 +#define CH_08 0x08 + +/* sample frequency index */ +#define RT722_SDCA_RATE_16000HZ 0x04 +#define RT722_SDCA_RATE_32000HZ 0x07 +#define RT722_SDCA_RATE_44100HZ 0x08 +#define RT722_SDCA_RATE_48000HZ 0x09 +#define RT722_SDCA_RATE_96000HZ 0x0b +#define RT722_SDCA_RATE_192000HZ 0x0d + +enum { + RT722_AIF1, /* For headset mic and headphone */ + RT722_AIF2, /* For speaker and dmic */ + RT722_AIFS, +}; + +enum rt722_sdca_jd_src { + RT722_JD_NULL, + RT722_JD1, +}; + +int rt722_sdca_io_init(struct device *dev, struct sdw_slave *slave); +int rt722_sdca_init(struct device *dev, struct regmap *regmap, + struct regmap *mbq_regmap, struct sdw_slave *slave); +int rt722_sdca_index_write(struct rt722_sdca_priv *rt722, + unsigned int nid, unsigned int reg, unsigned int value); +int rt722_sdca_index_read(struct rt722_sdca_priv *rt722, + unsigned int nid, unsigned int reg, unsigned int *value); + +int rt722_sdca_jack_detect(struct rt722_sdca_priv *rt722, bool *hp, bool *mic); +#endif /* __RT722_H__ */ -- 2.40.0

1 0

[PATCH] ALSA: Use of_property_read_bool() for boolean properties
by Rob Herring 19 Apr '23

19 Apr '23

It is preferred to use typed property access functions (i.e. of_property_read_<type> functions) rather than low-level of_get_property/of_find_property functions for reading properties. Convert reading boolean properties to to of_property_read_bool(). Signed-off-by: Rob Herring <robh(a)kernel.org> --- sound/ppc/tumbler.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/ppc/tumbler.c b/sound/ppc/tumbler.c index 6c882873b344..12f1e10db1c4 100644 --- a/sound/ppc/tumbler.c +++ b/sound/ppc/tumbler.c @@ -1361,7 +1361,7 @@ int snd_pmac_tumbler_init(struct snd_pmac *chip) for_each_child_of_node(chip->node, np) { if (of_node_name_eq(np, "sound")) { - if (of_get_property(np, "has-anded-reset", NULL)) + if (of_property_read_bool(np, "has-anded-reset")) mix->anded_reset = 1; if (of_property_present(np, "layout-id")) mix->reset_on_sleep = 0; -- 2.39.2

2 3

[PATCH] ALSA: ppc/tumbler: Use of_property_present() for testing DT property presence
by Rob Herring 19 Apr '23

19 Apr '23

It is preferred to use typed property access functions (i.e. of_property_read_<type> functions) rather than low-level of_get_property/of_find_property functions for reading properties. As part of this, convert of_get_property/of_find_property calls to the recently added of_property_present() helper when we just want to test for presence of a property and nothing more. Signed-off-by: Rob Herring <robh(a)kernel.org> --- sound/ppc/tumbler.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/ppc/tumbler.c b/sound/ppc/tumbler.c index f3f8ad7c3df8..6c882873b344 100644 --- a/sound/ppc/tumbler.c +++ b/sound/ppc/tumbler.c @@ -1363,7 +1363,7 @@ int snd_pmac_tumbler_init(struct snd_pmac *chip) if (of_node_name_eq(np, "sound")) { if (of_get_property(np, "has-anded-reset", NULL)) mix->anded_reset = 1; - if (of_get_property(np, "layout-id", NULL)) + if (of_property_present(np, "layout-id")) mix->reset_on_sleep = 0; of_node_put(np); break; -- 2.39.2

2 1

What is difference between snd_soc_xxx() vs asoc_xxx() ?
by Kuninori Morimoto 19 Apr '23

19 Apr '23

Hi ALSA ML Cc Mark I think ALSA SoC is using 2 type of prefix. snd_soc_xxx() asoc_xxx() But, what is difference these two ? If there was no big clear reasons, I think it is good idea to unify them, because it is confusable. But what do you think ? Thank you for your help !! Best regards --- Kuninori Morimoto

2 2

[PATCH 00/11] ASoC: add and use asoc_dummy_dlc
by Kuninori Morimoto 19 Apr '23

19 Apr '23

Hi Mark Many ASoC drivers are using dummy DAI. We can use common snd_soc_dai_link_component for it. This patch-set adds common asoc_dummy_dlc, and use it. Kuninori Morimoto (11): ASoC: soc-utils.c: add asoc_dummy_dlc ASoC: simple_card_utils.c: use asoc_dummy_dlc ASoC: ti: use asoc_dummy_dlc ASoC: sof: use asoc_dummy_dlc ASoC: amd: use asoc_dummy_dlc ASoC: fsl: use asoc_dummy_dlc ASoC: qcom: use asoc_dummy_dlc ASoC: atmel: use asoc_dummy_dlc ASoC: intel: use asoc_dummy_dlc ASoC: meson: use asoc_dummy_dlc ASoC: soc-topology.c: use asoc_dummy_dlc include/sound/simple_card_utils.h | 1 - include/sound/soc.h | 1 + sound/soc/amd/acp/acp-mach-common.c | 43 ++++++++------------ sound/soc/atmel/atmel-classd.c | 6 +-- sound/soc/atmel/atmel-pdmic.c | 6 +-- sound/soc/fsl/imx-audmix.c | 14 +++---- sound/soc/fsl/imx-card.c | 11 +---- sound/soc/fsl/imx-rpmsg.c | 3 +- sound/soc/fsl/imx-spdif.c | 6 +-- sound/soc/generic/simple-card-utils.c | 9 +--- sound/soc/intel/avs/boards/i2s_test.c | 6 +-- sound/soc/intel/boards/ehl_rt5660.c | 8 +--- sound/soc/intel/boards/skl_hda_dsp_generic.c | 8 +--- sound/soc/intel/boards/sof_cs42l42.c | 11 +---- sound/soc/intel/boards/sof_es8336.c | 11 +---- sound/soc/intel/boards/sof_nau8825.c | 11 +---- sound/soc/intel/boards/sof_pcm512x.c | 3 +- sound/soc/intel/boards/sof_rt5682.c | 14 ++----- sound/soc/intel/boards/sof_sdw.c | 13 +----- sound/soc/intel/boards/sof_ssp_amp.c | 18 +++----- sound/soc/meson/axg-card.c | 6 +-- sound/soc/meson/meson-card-utils.c | 10 +---- sound/soc/qcom/common.c | 11 +---- sound/soc/soc-topology.c | 12 +++--- sound/soc/soc-utils.c | 7 ++++ sound/soc/sof/nocodec.c | 8 ++-- sound/soc/ti/omap-hdmi.c | 6 +-- 27 files changed, 78 insertions(+), 185 deletions(-) -- 2.25.1 Thank you for your help !! Best regards --- Kuninori Morimoto

2 10

USB Audio (SPDIF) broken after 810367c
by GitHub issues - opened 19 Apr '23

19 Apr '23

alsa-project/alsa-ucm-conf issue #305 was opened from ZVNexus: Device: [ROG STRIX X670E-E GAMING WIFI](https://rog.asus.com/motherboards/rog-strix/rog-strix-x670e-e-gaming-… /proc/asound/card3/usbid: 0b05:1a52 Audio stopped working after this commit, not sure why. https://github.com/alsa-project/alsa-ucm-conf/commit/810367c244bf2d3dc0c535… Able to reproduce by deleting /usr/share/alsa/ucm*, copying from before this commit, and after this commit. Issue URL : https://github.com/alsa-project/alsa-ucm-conf/issues/305 Repository URL: https://github.com/alsa-project/alsa-ucm-conf

1 0

[PATCH 0/4] ASoC: cs35l56: Updates for B0 silicon
by Richard Fitzgerald 18 Apr '23

18 Apr '23

These patches make some small changes to align with the B0 silicon revision. Richard Fitzgerald (4): ASoC: cs35l56: Update comment on masking of EINT20 interrupts ASoC: cs35l56: Remove SDW1 TX5 and TX6 ASoC: cs35l56: Remove SDW2RX1 mixer source ASoC: cs35l56: Rename mixer source defines for SoundWire DP1 include/sound/cs35l56.h | 10 +++------ sound/soc/codecs/cs35l56-shared.c | 34 +++---------------------------- sound/soc/codecs/cs35l56.c | 30 ++------------------------- 3 files changed, 8 insertions(+), 66 deletions(-) -- 2.30.2

2 5

[PATCH 1/4] ASoC: codecs: wcd9335: Simplify with dev_err_probe
by Krzysztof Kozlowski 18 Apr '23

18 Apr '23

Code can be a bit simpler with dev_err_probe(). Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski(a)linaro.org> --- sound/soc/codecs/wcd9335.c | 27 +++++++++++---------------- 1 file changed, 11 insertions(+), 16 deletions(-) diff --git a/sound/soc/codecs/wcd9335.c b/sound/soc/codecs/wcd9335.c index d2548fdf9ae5..8bf3510a3ea3 100644 --- a/sound/soc/codecs/wcd9335.c +++ b/sound/soc/codecs/wcd9335.c @@ -5138,20 +5138,17 @@ static int wcd9335_irq_init(struct wcd9335_codec *wcd) * INTR2 is a subset of first interrupt sources MAD, VBAT, and SVA */ wcd->intr1 = of_irq_get_byname(wcd->dev->of_node, "intr1"); - if (wcd->intr1 < 0) { - if (wcd->intr1 != -EPROBE_DEFER) - dev_err(wcd->dev, "Unable to configure IRQ\n"); - - return wcd->intr1; - } + if (wcd->intr1 < 0) + return dev_err_probe(wcd->dev, wcd->intr1, + "Unable to configure IRQ\n"); ret = devm_regmap_add_irq_chip(wcd->dev, wcd->regmap, wcd->intr1, IRQF_TRIGGER_HIGH, 0, &wcd9335_regmap_irq1_chip, &wcd->irq_data); if (ret) - dev_err(wcd->dev, "Failed to register IRQ chip: %d\n", ret); + return dev_err_probe(wcd->dev, ret, "Failed to register IRQ chip\n"); - return ret; + return 0; } static int wcd9335_slim_probe(struct slim_device *slim) @@ -5207,17 +5204,15 @@ static int wcd9335_slim_status(struct slim_device *sdev, slim_get_logical_addr(wcd->slim_ifc_dev); wcd->regmap = regmap_init_slimbus(sdev, &wcd9335_regmap_config); - if (IS_ERR(wcd->regmap)) { - dev_err(dev, "Failed to allocate slim register map\n"); - return PTR_ERR(wcd->regmap); - } + if (IS_ERR(wcd->regmap)) + return dev_err_probe(dev, PTR_ERR(wcd->regmap), + "Failed to allocate slim register map\n"); wcd->if_regmap = regmap_init_slimbus(wcd->slim_ifc_dev, &wcd9335_ifc_regmap_config); - if (IS_ERR(wcd->if_regmap)) { - dev_err(dev, "Failed to allocate ifc register map\n"); - return PTR_ERR(wcd->if_regmap); - } + if (IS_ERR(wcd->if_regmap)) + return dev_err_probe(dev, PTR_ERR(wcd->if_regmap), + "Failed to allocate ifc register map\n"); ret = wcd9335_bring_up(wcd); if (ret) { -- 2.34.1

2 13