May 2023 - Alsa-devel - mailman.alsa-project.org

Yamaha YIT-W12TX not working
by Julian Sikorski 27 Nov '23

27 Nov '23

Hi list, Yamaha YIT-W12TX is a USB dongle which allows to transmit audio from PC to the YSP-4300 sound bar [1][2]. While it is quite old and no longer sold, I recently tried to make it work under linux. Unfortunately, it did not work: [ 3676.366404] usb 2-1.1: new full-speed USB device number 5 using ehci-pci [ 3676.445995] usb 2-1.1: config 1 has an invalid interface number: 4 but max is 3 [ 3676.446001] usb 2-1.1: config 1 has no interface number 2 [ 3676.446664] usb 2-1.1: New USB device found, idVendor=0499, idProduct=3108, bcdDevice= 1.00 [ 3676.446666] usb 2-1.1: New USB device strings: Mfr=2, Product=1, SerialNumber=0 [ 3676.446679] usb 2-1.1: Product: YIT-W12TX [ 3676.446683] usb 2-1.1: Manufacturer: YAMAHA Corp. [ 3676.449508] hid-generic 0003:0499:3108.0001: hiddev96,hidraw0: USB HID v0.01 Device [YAMAHA Corp. YIT-W12TX] on usb-0000:00:1d.0-1.1/input3 [ 3676.450846] input: YAMAHA Corp. YIT-W12TX as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.4/0003:0499:3108.0002/input/input34 [ 3676.503844] hid-generic 0003:0499:3108.0002: input,hidraw1: USB HID v1.00 Device [YAMAHA Corp. YIT-W12TX] on usb-0000:00:1d.0-1.1/input4 [ 3676.671641] usb 2-1.1: 1:1: cannot get freq at ep 0x1 [ 3676.675786] usb 2-1.1: 5:0: cannot get min/max values for control 2 (id 5) [ 3676.676476] usbcore: registered new interface driver snd-usb-audio [ 3676.731911] usb 2-1.1: 5:0: cannot get min/max values for control 2 (id 5) [ 3676.735658] usb 2-1.1: 5:0: cannot get min/max values for control 2 (id 5) [ 3676.739399] usb 2-1.1: 5:0: cannot get min/max values for control 2 (id 5) [ 3676.743131] usb 2-1.1: 5:0: cannot get min/max values for control 2 (id 5) [ 3676.746920] usb 2-1.1: 5:0: cannot get min/max values for control 2 (id 5) [ 3676.750648] usb 2-1.1: 5:0: cannot get min/max values for control 2 (id 5) [ 3676.754445] usb 2-1.1: 5:0: cannot get min/max values for control 2 (id 5) [ 3676.758524] usb 2-1.1: 5:0: cannot get min/max values for control 2 (id 5) [ 3676.762274] usb 2-1.1: 5:0: cannot get min/max values for control 2 (id 5) [ 3676.789671] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.790049] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.790414] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.790773] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.791169] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.792134] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.792547] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.792899] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.793254] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.793634] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.794900] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.795255] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.795634] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.796008] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.796384] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.797543] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.797879] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.798254] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.798634] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.799007] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.813819] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.814281] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.814686] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.815281] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.815929] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.817807] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.818155] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.818592] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.819165] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.819801] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.822163] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.822802] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.823284] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.824161] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.824907] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.827683] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.828159] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.828675] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.829415] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.830157] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.841801] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.842155] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.842551] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.843158] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.843785] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.844909] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.845283] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.845673] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.846156] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.846800] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.848287] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.848799] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.849280] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.850031] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.850799] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.852677] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.853154] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.853674] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.854429] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.855155] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.858916] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.859277] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.859672] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.860280] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.860909] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.862033] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.862418] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.862797] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.863279] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.863923] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.865471] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.866033] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.866590] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.867410] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.868157] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.870162] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.870674] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.871155] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.871908] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.872676] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 [ 3676.900672] usb 2-1.1: USB disconnect, device number 5 [ 3676.900688] usb 2-1.1: 1:1: cannot set freq 44100 to ep 0x1 This is with kernel-5.9.13-200.fc33.x86_64 and alsa-lib-1.2.4-5.fc33.x86_64 on Fedora 33. Under Windows 10 the dongle works without any special drivers from Yamaha, everything appears to be downloaded by Windows automatically, so I was hoping the device could be made to work under Linux relatively easily. Best regards, Julian [1] https://europe.yamaha.com/en/products/audio_visual/accessories/yit-w12/down… [2] https://europe.yamaha.com/en/products/audio_visual/sound_bar/ysp-4300/downl…

2 7

Re: RFC: usb: gadget: u_audio: Notifying gadget that host started playback/capture?
by Pavel Hofman 30 Oct '23

30 Oct '23

Hi, Dne 08. 09. 21 v 10:21 Pavel Hofman napsal(a): > Hi, > > The current audio gadget has no way to inform the gadget side that the > host side has started playback/capture and that gadget-side alsa > processes should be started. > > Playback/capture processes on the host side do not get stuck without the > gadget side consuming/producing data (OUT requests are ignored in > u_audio_iso_complete, IN ones send initial zeros in their req->buf). > > However, playback/capture processes on the gadget side get stuck without > the host side sending playback OUT packets or capture IN requests and > time out with error. If there was a way to inform the gadget side that > playback/capture has started on the host side, the gadget clients could > react accordingly. > I drafted a simple patch for u_audio.c which defines read-only boolean ctl elems "Capture Requested" and "Playback Requested". Their values are set/reset in methods u_audio_start_capture/playback and u_audio_stop_capture/playback, i.e. at changes of respective altsettings from 0 to 1 and back. Every ctl elem value change sends notification via snd_ctl_notify. The principle works OK for capture/playback start/stop on the host, as monitored by alsactl: pi@raspberrypi:~ $ alsactl monitor hw:UAC2Gadget node hw:UAC2Gadget, #4 (3,0,0,Capture Requested,0) VALUE node hw:UAC2Gadget, #4 (3,0,0,Capture Requested,0) VALUE node hw:UAC2Gadget, #3 (3,0,0,Playback Requested,0) VALUE node hw:UAC2Gadget, #3 (3,0,0,Playback Requested,0) VALUE However at enumeration the USB host switches both playback and capture altsettings repeatedly, generating "fake" events from the gadget side POW. The host even sends regular-sized EP-OUT packets filled with zeros during enumeration (tested on linux only for now). Please is there any way to "detect" the enumeration stage to mask out the "fake" playback/capture start/stop events? The attached patch does not apply cleanly to mainline u_audio.c because it's rebased on other patches not submitted yet but it's only a discussion inducer for now. Thanks a lot, Pavel.

2 6

[PATCH 0/4] ASoC: qcom: fixes for Click/Pop Noise
by Srinivas Kandagatla 27 Oct '23

27 Oct '23

Click/Pop Noise was a long pending issue with WSA Codecs which are prone to accumlate DC when ports are active but without any data streams. There are multiple places in the current setup, where this could happen in both startup as well as shutdown path. This patches help fix those issues by making sure the PA is Muted/Unmuted inline with the stream start/stop events. Other than this there is a patch to fix DSP graph saturation issue as we never unload playback graph before loading same graph. Srinivas Kandagatla (4): ASoC: qcom: q6apm-lpass-dai: close graphs before opening a new one ASoC: qcom: sdw: do not restart soundwire ports for every prepare ASoC: codecs: wsa883x: mute/unmute PA in correct sequence ASoC: codecs: wsa881x: mute/unmute PA in correct sequence sound/soc/codecs/wsa881x.c | 30 ++++++++++++++++++++- sound/soc/codecs/wsa883x.c | 36 ++++++++++++++++++++----- sound/soc/qcom/qdsp6/q6apm-lpass-dais.c | 3 +++ sound/soc/qcom/sdw.c | 7 ++--- 4 files changed, 63 insertions(+), 13 deletions(-) -- 2.21.0

4 16

[alsa-devel] echo-cancellation plugin advice?
by Max Klein 27 Oct '23

27 Oct '23

> Well, asym wouldn't be the answer. Basically you'll need to open two > slave PCMs in one plugin. So, it's no simple filter-type plugin. > It's doable, but not easy as it sounds, I guess. Takashi, can you please further explain why asym is not the solution and what you see as a problem? I am also trying to figure out if it would be possible to create such a plugin for ALSA? I am still searching for some good starting points on how to write an ALSA plugin... Jean-Marc Valin (http://lists.linuxaudio.org/pipermail/linux-audio-dev/2005-June/012454.html) already released his work as part of speex but as far I know there is no plugin that has been made out of it? Thanks for any hint! -- NEU: FreePhone 3-fach-Flat mit kostenlosem Smartphone! Jetzt informieren: http://mobile.1und1.de/?ac=OM.PW.PW003K20328T7073a

3 2

ALSA 1.2.8 release
by Jaroslav Kysela 01 Sep '23

01 Sep '23

Hello all, new ALSA userspace packages were released. You may download them from the ALSA website http://www.alsa-project.org or directly: HTTP: https://www.alsa-project.org/files/pub FTP: ftp://ftp.alsa-project.org/pub Released packages: alsa-lib alsa-utils alsa-ucm-conf tinycompress Full list of changes: https://www.alsa-project.org/wiki/Changes_v1.2.7.2_v1.2.8 The fingerprint of the public signing key is: F04D F507 37AC 1A88 4C4B 3D71 8380 596D A6E5 9C91 Have fun, Jaroslav -- Jaroslav Kysela <perex(a)perex.cz> Linux Sound Maintainer; ALSA Project; Red Hat, Inc.

1 2

[PATCH v3 00/28] Introduce QC USB SND audio offloading support
by Wesley Cheng 29 Aug '23

29 Aug '23

Changes in v3: - Changed prefix from RFC to PATCH - Rebased entire series to usb-next - Updated copyright years XHCI: - Rebased changes on top of XHCI changes merged into usb-next, and only added changes that were still under discussion. - Added change to read in the "num-hc-interrupters" device property. ASoC: - qusb6 USB backend - Incorporated suggestions to fetch iommu information with existing APIs - Added two new sound kcontrols to fetch offload status and offload device selection. - offload status - will return the card and pcm device in use tinymix -D 0 get 1 --> 1, 0 (offload in progress on card#1 pcm#0) - device selection - set the card and pcm device to enable offload on. Ex.: tinymix -D 0 set 1 2 0 --> sets offload on card#2 pcm#0 (this should be the USB card) USB SND: - Fixed up some locking related concerns for registering platform ops. - Moved callbacks under the register_mutex, so that - Modified APIs to properly pass more information about the USB SND device, so that the Q6USB backend can build a device list/map, in order to monitor offload status and device selection. Changes in v2: XHCI: - Replaced XHCI and HCD changes with Mathias' XHCI interrupter changes in his tree: https://git.kernel.org/pub/scm/linux/kernel/git/mnyman/xhci.git/log/?h=feat… Adjustments made to Mathias' changes: - Created xhci-intr.h to export/expose interrupter APIs versus exposing xhci.h. Moved dependent structures to this file as well. (so clients can parse out information from "struct xhci_interrupter") - Added some basic locking when requesting interrupters. - Fixed up some sanity checks. - Removed clearing of the ERSTBA during freeing of the interrupter. (pending issue where SMMU fault occurs if DMA addr returned is 64b - TODO) - Clean up pending events in the XHCI secondary interrupter. While testing USB bus suspend, it was seen that on bus resume, the xHCI HC would run into a command timeout. - Added offloading APIs to xHCI to fetch transfer and event ring information. ASoC: - Modified soc-usb to allow for multiple USB port additions. For this to work, the USB offload driver has to have a reference to the USB backend by adding a "usb-soc-be" DT entry to the device saved into XHCI sysdev. - Created separate dt-bindings for defining USB_RX port. - Increased APR timeout to accommodate the situation where the AFE port start command could be delayed due to having to issue a USB bus resume while handling the QMI stream start command. USB SND: - Added a platform ops during usb_audio_suspend(). This allows for the USB offload driver to halt the audio stream when system enters PM suspend. This ensures the audio DSP is not issuing transfers on the USB bus. - Do not override platform ops if they are already populated. - Introduce a shared status variable between the USB offload and USB SND layers, to ensure that only one path is active at a time. If the USB bus is occupied, then userspace is notified that the path is busy. Several Qualcomm based chipsets can support USB audio offloading to a dedicated audio DSP, which can take over issuing transfers to the USB host controller. The intention is to reduce the load on the main processors in the SoC, and allow them to be placed into lower power modes. There are several parts to this design: 1. Adding ASoC binding layer 2. Create a USB backend for Q6DSP 3. Introduce XHCI interrupter support 4. Create vendor ops for the USB SND driver Adding ASoC binding layer: soc-usb: Intention is to treat a USB port similar to a headphone jack. The port is always present on the device, but cable/pin status can be enabled/disabled. Expose mechanisms for USB backend ASoC drivers to communicate with USB SND. Create a USB backend for Q6DSP: q6usb: Basic backend driver that will be responsible for maintaining the resources needed to initiate a playback stream using the Q6DSP. Will be the entity that checks to make sure the connected USB audio device supports the requested PCM format. If it does not, the PCM open call will fail, and userpsace ALSA can take action accordingly. Introduce XHCI interrupter support: XHCI HCD supports multiple interrupters, which allows for events to be routed to different event rings. This is determined by "Interrupter Target" field specified in Section "6.4.1.1 Normal TRB" of the XHCI specification. Events in the offloading case will be routed to an event ring that is assigned to the audio DSP. Create vendor ops for the USB SND driver: qc_audio_offload: This particular driver has several components associated with it: - QMI stream request handler - XHCI interrupter and resource management - audio DSP memory management When the audio DSP wants to enable a playback stream, the request is first received by the ASoC platform sound card. Depending on the selected route, ASoC will bring up the individual DAIs in the path. The Q6USB backend DAI will send an AFE port start command (with enabling the USB playback path), and the audio DSP will handle the request accordingly. Part of the AFE USB port start handling will have an exchange of control messages using the QMI protocol. The qc_audio_offload driver will populate the buffer information: - Event ring base address - EP transfer ring base address and pass it along to the audio DSP. All endpoint management will now be handed over to the DSP, and the main processor is not involved in transfers. Overall, implementing this feature will still expose separate sound card and PCM devices for both the platorm card and USB audio device: 0 [SM8250MTPWCD938]: sm8250 - SM8250-MTP-WCD9380-WSA8810-VA-D SM8250-MTP-WCD9380-WSA8810-VA-DMIC 1 [Audio ]: USB-Audio - USB Audio Generic USB Audio at usb-xhci-hcd.1.auto-1.4, high speed This is to ensure that userspace ALSA entities can decide which route to take when executing the audio playback. In the above, if card#1 is selected, then USB audio data will take the legacy path over the USB PCM drivers, etc... This feature was validated using: - tinymix: set/enable the multimedia path to route to USB backend - tinyplay: issue playback on platform card Mathias Nyman (1): xhci: Add support to allocate several interrupters Wesley Cheng (27): usb: xhci: Add XHCI APIs to support USB offloading usb: host: xhci-mem: Cleanup pending secondary event ring events ASoC: Add SOC USB APIs for adding an USB backend ASoC: dt-bindings: qcom,q6dsp-lpass-ports: Add USB_RX port ASoC: qcom: qdsp6: Introduce USB AFE port to q6dsp ASoC: qdsp6: q6afe: Increase APR timeout ASoC: qcom: Add USB backend ASoC driver for Q6 sound: usb: card: Introduce USB SND platform op callbacks sound: usb: Export USB SND APIs for modules dt-bindings: usb: dwc3: Add snps,num-hc-interrupters definition usb: dwc3: Add DT parameter to specify maximum number of interrupters usb: host: xhci-plat: Set XHCI max interrupters if property is present sound: usb: pcm: Export fixed rate check USB SND API sound: usb: Introduce QC USB SND offloading support sound: usb: card: Check for support for requested audio format sound: soc: soc-usb: Add PCM format check API for USB backend sound: soc: qcom: qusb6: Ensure PCM format is supported by USB audio device sound: usb: Prevent starting of audio stream if in use ASoC: dt-bindings: Add Q6USB backend bindings ASoC: dt-bindings: Update example for enabling USB offload on SM8250 ASoC: qcom: qdsp6: q6afe: Split USB AFE dev_token param into separate API sound: Pass USB SND card and PCM information to SOC USB sound: soc: qdsp6: Add SND kcontrol to select offload device sound: soc: qdsp6: Add SND kcontrol for fetching offload status sound: usb: qc_audio_offload: Use card and PCM index from QMI request sound: usb: card: Allow for rediscovery of connected USB SND devices sound: soc: soc-usb: Rediscover USB SND devices on USB port add .../bindings/sound/qcom,q6usb-dais.yaml | 49 + .../bindings/sound/qcom,sm8250.yaml | 15 + .../devicetree/bindings/usb/snps,dwc3.yaml | 13 + drivers/usb/dwc3/core.c | 12 + drivers/usb/dwc3/core.h | 2 + drivers/usb/dwc3/host.c | 5 +- drivers/usb/host/xhci-debugfs.c | 2 +- drivers/usb/host/xhci-mem.c | 171 +- drivers/usb/host/xhci-plat.c | 2 + drivers/usb/host/xhci-ring.c | 2 +- drivers/usb/host/xhci.c | 181 +- drivers/usb/host/xhci.h | 2 +- .../sound/qcom,q6dsp-lpass-ports.h | 1 + include/linux/usb/xhci-intr.h | 94 + include/sound/pcm_params.h | 4 + include/sound/q6usboffload.h | 20 + include/sound/soc-usb.h | 39 + sound/core/oss/pcm_oss.c | 58 - sound/core/pcm_lib.c | 65 + sound/soc/Makefile | 2 +- sound/soc/qcom/Kconfig | 4 + sound/soc/qcom/qdsp6/Makefile | 1 + sound/soc/qcom/qdsp6/q6afe-dai.c | 50 + sound/soc/qcom/qdsp6/q6afe.c | 208 +- sound/soc/qcom/qdsp6/q6afe.h | 47 +- sound/soc/qcom/qdsp6/q6dsp-lpass-ports.c | 23 + sound/soc/qcom/qdsp6/q6dsp-lpass-ports.h | 1 + sound/soc/qcom/qdsp6/q6routing.c | 9 + sound/soc/qcom/qdsp6/q6usb.c | 445 ++++ sound/soc/soc-usb.c | 197 ++ sound/usb/Kconfig | 14 + sound/usb/Makefile | 2 +- sound/usb/card.c | 85 + sound/usb/card.h | 31 + sound/usb/endpoint.c | 2 + sound/usb/helper.c | 1 + sound/usb/pcm.c | 29 +- sound/usb/pcm.h | 12 + sound/usb/qcom/Makefile | 2 + sound/usb/qcom/qc_audio_offload.c | 1790 +++++++++++++++++ sound/usb/qcom/usb_audio_qmi_v01.c | 892 ++++++++ sound/usb/qcom/usb_audio_qmi_v01.h | 162 ++ 42 files changed, 4646 insertions(+), 100 deletions(-) create mode 100644 Documentation/devicetree/bindings/sound/qcom,q6usb-dais.yaml create mode 100644 include/linux/usb/xhci-intr.h create mode 100644 include/sound/q6usboffload.h create mode 100644 include/sound/soc-usb.h create mode 100644 sound/soc/qcom/qdsp6/q6usb.c create mode 100644 sound/soc/soc-usb.c create mode 100644 sound/usb/qcom/Makefile create mode 100644 sound/usb/qcom/qc_audio_offload.c create mode 100644 sound/usb/qcom/usb_audio_qmi_v01.c create mode 100644 sound/usb/qcom/usb_audio_qmi_v01.h

12 80

[PATCH 0/4] ASoC: amd: acp: Add sound support for a line of HUAWEI laptops
by Marian Postevca 21 Aug '23

21 Aug '23

This series adds support for a line of HUAWEI laptops with AMD CPUs that connect using the ACP3x module to a ES8336 codec. The codec driver must be extended to support the S32 LE format and the MCLK div by 2 option. MCLK div by 2 is needed for one specific SKU which uses a 48Mhz MCLK which seems to be too high of a frequency for the codec and must be divided by 2. The acp legacy driver must also be extended by using callbacks so that the more complicated handling for this specific codec can be moved outside the more generic ACP code. The last patch tries to avoid anoying pop sounds when the speaker/headphones are enabled/disabled by delaying the handling of the GPIOs and using a mutex to avoid race conditions between the speaker power event callback and the trigger callback. Marian Postevca (4): ASoC: es8316: Enable support for S32 LE format and MCLK div by 2 ASoC: amd: acp: Add support for splitting the codec specific code from the ACP driver ASoC: amd: acp: Add machine driver that enables sound for systems with a ES8336 codec ASoC: amd: acp: Improve support for speaker power events sound/soc/amd/acp-config.c | 70 ++ sound/soc/amd/acp/Makefile | 2 +- sound/soc/amd/acp/acp-legacy-mach.c | 105 ++- sound/soc/amd/acp/acp-mach-common.c | 8 + sound/soc/amd/acp/acp-mach.h | 67 ++ sound/soc/amd/acp/acp-renoir.c | 4 + sound/soc/amd/acp/acp3x-es83xx/acp3x-es83xx.c | 615 ++++++++++++++++++ sound/soc/amd/acp/acp3x-es83xx/acp3x-es83xx.h | 12 + sound/soc/codecs/es8316.c | 21 +- sound/soc/codecs/es8316.h | 3 + 10 files changed, 886 insertions(+), 21 deletions(-) create mode 100644 sound/soc/amd/acp/acp3x-es83xx/acp3x-es83xx.c create mode 100644 sound/soc/amd/acp/acp3x-es83xx/acp3x-es83xx.h -- 2.39.1

4 25

Fwd: [Bug 217440] New: ALC236 audio disappears from HP 15z-fc000 on warm boot
by Joseph C. Sible 16 Aug '23

16 Aug '23

Hello, Forwarding my regression bug report submission per the instructions in "Reporting regressions". #regzbot introduced: 5aec989130 https://bugzilla.kernel.org/show_bug.cgi?id=217440 Regards, Joseph C. Sible ---------- Forwarded message --------- From: <bugzilla-daemon(a)kernel.org> Date: Sat, May 13, 2023 at 3:46 PM Subject: [Bug 217440] New: ALC236 audio disappears from HP 15z-fc000 on warm boot To: <josephcsible(a)gmail.com> https://bugzilla.kernel.org/show_bug.cgi?id=217440 Bug ID: 217440 Summary: ALC236 audio disappears from HP 15z-fc000 on warm boot Product: Drivers Version: 2.5 Kernel Version: 6.3.2 Hardware: All OS: Linux Status: NEW Severity: normal Priority: P3 Component: Sound(ALSA) Assignee: perex(a)perex.cz Reporter: josephcsible(a)gmail.com Regression: Yes Bisected 5aec98913095ed3b4424ed6c5fdeb6964e9734da commit-id: On an HP 15z-fc000 laptop that uses Realtek ALC236 for sound, once the system is warm booted ("reboot" from within Linux), sound stops working completely and the device doesn't even show up anymore. Once this happens, the only way to get it to come back is to cold boot ("poweroff" from within Linux, wait for it to turn completely off, and turn it back on with the physical power button). In particular, once you boot from a "bad" kernel, no number of warm boots with "good" kernels will ever bring sound back. I bisected this to commit 5aec989, which first appeared in 5.15-rc6. In addition, I confirmed by doing a custom build of 6.3.2 with reverts of both f30741c (just to avoid a conflict) and 5aec989, which works correctly for me. -- You may reply to this email to add a comment. You are receiving this mail because: You reported the bug.

5 48

Audio output heavily distorted on Xen PV dom0 if not recording (Intel ADL)
by Marek Marczykowski-Górecki 01 Aug '23

01 Aug '23

Hi, I have a rather interesting issue on HP EliteBook 1040, with Intel ADL HDA. Sometimes (often) audio output is heavily distorted, but then opening pavucontrol or just launching `parecord /dev/null` fixes the issue instantly. But, when the mixer or recording is closed, then few seconds later issue comes back. You can hear this at https://cloud.marmarek.net/s/46prqZnwrqDkBdD Initially recording was running, then about 10s stopped and you can hear the issue few seconds later. Then I starter recording again, and the issue is gone. This is how it should sound: https://youtube.com/watch?v=4Tr0otuiQuU I do not see any kernel messages when issue happens. The issue happens on Linux 6.1.26, 6.2.10, and 6.3.2. I haven't tested other versions. It happens only when running under Xen (in PV dom0). The very same Linux started directly works fine. Full dmesg of both native and Xen boots is at https://gist.github.com/marmarek/548ee79282446344a172109bcd943930 When running Linux 6.3.2 there, I noticed that just after boot first playback is okay, but if I start and stop recording it breaks. And then after some time of idle it fixes itself again. I have not observed this behavior on 6.2.10 (it was broken initially too), but I could be also doing some things differently. I have few other ADL-based systems (but not HP), and they do not show this issue, only this HP laptop is affected. Example dmesg from another ADL-based system: https://gist.github.com/marmarek/38c5ba3ec58f9300fbc1842ddc9fa4f5 I'm not sure if that's the relevant difference, but comparing dmesg from working and not working systems, I see those on boot for the problematic case: snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100 snd_hda_intel 0000:00:1f.3: Digital mics found on Skylake+ platform, using SOF driver sof-audio-pci-intel-tgl 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100 sof-audio-pci-intel-tgl 0000:00:1f.3: Digital mics found on Skylake+ platform, using SOF driver sof-audio-pci-intel-tgl 0000:00:1f.3: enabling device (0000 -> 0002) xen: registering gsi 16 triggering 0 polarity 1 Already setup the GSI :16 sof-audio-pci-intel-tgl 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if 0x040100 sof-audio-pci-intel-tgl 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915]) sof-audio-pci-intel-tgl 0000:00:1f.3: use msi interrupt mode sof-audio-pci-intel-tgl 0000:00:1f.3: hda codecs found, mask 5 sof-audio-pci-intel-tgl 0000:00:1f.3: using HDA machine driver skl_hda_dsp_generic now sof-audio-pci-intel-tgl 0000:00:1f.3: DMICs detected in NHLT tables: 2 sof-audio-pci-intel-tgl 0000:00:1f.3: Firmware info: version 2:2:0-57864 sof-audio-pci-intel-tgl 0000:00:1f.3: Firmware: ABI 3:22:1 Kernel ABI 3:23:0 sof-audio-pci-intel-tgl 0000:00:1f.3: unknown sof_ext_man header type 3 size 0x30 sof-audio-pci-intel-tgl 0000:00:1f.3: Firmware info: version 2:2:0-57864 sof-audio-pci-intel-tgl 0000:00:1f.3: Firmware: ABI 3:22:1 Kernel ABI 3:23:0 sof-audio-pci-intel-tgl 0000:00:1f.3: Topology: ABI 3:22:1 Kernel ABI 3:23:0 skl_hda_dsp_generic skl_hda_dsp_generic: ASoC: Parent card not yet available, widget card binding deferred cs35l41-hda spi0-CSC3551:00-cs35l41-hda.0: DSP1: Firmware version: 3 cs35l41-hda spi0-CSC3551:00-cs35l41-hda.0: DSP1: cirrus/cs35l41-dsp1-spk-prot-103c8974.wmfw: Fri 27 Aug 2021 14:58:19 W. Europe Daylight Time cs35l41-hda spi0-CSC3551:00-cs35l41-hda.0: DSP1: Firmware: 400a4 vendor: 0x2 v0.43.1, 2 algorithms cs35l41-hda spi0-CSC3551:00-cs35l41-hda.0: DSP1: 0: ID cd v29.63.1 XM@94 YM@e cs35l41-hda spi0-CSC3551:00-cs35l41-hda.0: DSP1: 1: ID f20b v0.1.0 XM@176 YM@0 cs35l41-hda spi0-CSC3551:00-cs35l41-hda.0: DSP1: spk-prot: E:\Amp Tuning\HP\840\0527\103C8972_220527.bin snd_hda_codec_realtek ehdaudio0D0: bound spi0-CSC3551:00-cs35l41-hda.0 (ops cs35l41_hda_comp_ops [snd_hda_scodec_cs35l41]) cs35l41-hda spi0-CSC3551:00-cs35l41-hda.1: DSP1: Firmware version: 3 cs35l41-hda spi0-CSC3551:00-cs35l41-hda.1: DSP1: cirrus/cs35l41-dsp1-spk-prot-103c8974.wmfw: Fri 27 Aug 2021 14:58:19 W. Europe Daylight Time cs35l41-hda spi0-CSC3551:00-cs35l41-hda.1: DSP1: Firmware: 400a4 vendor: 0x2 v0.43.1, 2 algorithms cs35l41-hda spi0-CSC3551:00-cs35l41-hda.1: DSP1: 0: ID cd v29.63.1 XM@94 YM@e cs35l41-hda spi0-CSC3551:00-cs35l41-hda.1: DSP1: 1: ID f20b v0.1.0 XM@176 YM@0 cs35l41-hda spi0-CSC3551:00-cs35l41-hda.1: DSP1: spk-prot: E:\Amp Tuning\HP\840\0527\103C8972_220527.bin snd_hda_codec_realtek ehdaudio0D0: bound spi0-CSC3551:00-cs35l41-hda.1 (ops cs35l41_hda_comp_ops [snd_hda_scodec_cs35l41]) Any ideas? -- Best Regards, Marek Marczykowski-Górecki Invisible Things Lab

3 6

[PATCH v2 00/37] ALSA: Add MIDI 2.0 support
by Takashi Iwai 12 Jul '23

12 Jul '23

Hi, this is a revised patch set for adding the support of MIDI 2.0 functionality. Only a few minor updates since v1 as below: * Bump CTL protocol version to 2.0.9 * Add two more ioctls for control API to receive UMP EP and block info * Minor compile warning fixes * Documentation fix and addition of two new ioctls * Put acks The latest code is found in topic/midi20 branch of sound git tree. And below is the cover letter of v1, which is still valid: Hi, this is a (largish) patch set for adding the support of MIDI 2.0 functionality, mainly targeted for USB devices. MIDI 2.0 is a complete overhaul of the 40-years old MIDI 1.0. Unlike MIDI 1.0 byte stream, MIDI 2.0 uses packets in 32bit words for Universal MIDI Packet (UMP) protocol. It supports both MIDI 1.0 commands for compatibility and the extended MIDI 2.0 commands for higher resolutions and more functions. For supporting the UMP, the patch set extends the existing ALSA rawmidi and sequencer interfaces, and adds the USB MIDI 2.0 support to the standard USB-audio driver. The rawmidi for UMP has a different device name (/dev/snd/umpC*D*) and it reads/writes UMP packet data in 32bit CPU-native endianness. For the old MIDI 1.0 applications, the legacy rawmidi interface is provided, too. As default, USB-audio driver will take the alternate setting for MIDI 2.0 interface, and the compatibility with MIDI 1.0 is provided via the rawmidi common layer. However, user may let the driver falling back to the old MIDI 1.0 interface by a module option, too. A UMP-capable rawmidi device can create the corresponding ALSA sequencer client(s) to support the UMP Endpoint and UMP Group connections. As a nature of ALSA sequencer, arbitrary connections between clients/ports are allowed, and the ALSA sequencer core performs the automatic conversions for the connections between a new UMP sequencer client and a legacy MIDI 1.0 sequencer client. It allows the existing application to use MIDI 2.0 devices without changes. The MIDI-CI, which is another major extension in MIDI 2.0, isn't covered by this patch set. It would be implemented rather in user-space. Roughly speaking, the first half of this patch set is for extending the rawmidi and USB-audio, and the second half is for extending the ALSA sequencer interface. The patch set is based on 6.4-rc2 kernel, but all patches can be cleanly applicable on 6.2 and 6.3 kernels, too (while 6.1 and older kernels would need minor adjustment for uapi header changes). The updates for alsa-lib and alsa-utils will follow shortly later. The author thanks members of MIDI Association OS/API Working Group, especially Andrew Mee, for great helps for the initial design and debugging / testing the drivers. Takashi --- Takashi Iwai (37): ALSA: rawmidi: Pass rawmidi directly to snd_rawmidi_kernel_open() ALSA: rawmidi: Add ioctl callback to snd_rawmidi_global_ops ALSA: rawmidi: UMP support ALSA: rawmidi: Skip UMP devices at SNDRV_CTL_IOCTL_RAWMIDI_NEXT_DEVICE ALSA: ump: Add ioctls to inquiry UMP EP and Block info via control API ALSA: ump: Additional proc output ALSA: usb-audio: Manage number of rawmidis globally ALSA: usb-audio: Define USB MIDI 2.0 specs ALSA: usb-audio: USB MIDI 2.0 UMP support ALSA: usb-audio: Get UMP EP name string from USB interface ALSA: usb-audio: Trim superfluous "MIDI" suffix from UMP EP name ALSA: usb-audio: Create UMP blocks from USB MIDI GTBs ALSA: ump: Redirect rawmidi substream access via own helpers ALSA: ump: Add legacy raw MIDI support ALSA: usb-audio: Enable the legacy raw MIDI support ALSA: usb-audio: Inform inconsistent protocols in GTBs ALSA: seq: Clear padded bytes at expanding events ALSA: seq: Add snd_seq_expand_var_event_at() helper ALSA: seq: Treat snd_seq_client object directly in client drivers ALSA: seq: Drop dead code for the old broadcast support ALSA: seq: Check the conflicting port at port creation ALSA: seq: Check validity before creating a port object ALSA: seq: Prohibit creating ports with special numbers ALSA: seq: Introduce SNDRV_SEQ_IOCTL_USER_PVERSION ioctl ALSA: seq: Add UMP support ALSA: seq: Add port inactive flag ALSA: seq: Support MIDI 2.0 UMP Endpoint port ALSA: seq: Add port direction to snd_seq_port_info ALSA: seq: Add UMP group number to snd_seq_port_info ALSA: seq: Automatic conversion of UMP events ALSA: seq: Allow suppressing UMP conversions ALSA: seq: Bind UMP device ALSA: seq: ump: Create UMP Endpoint port for broadcast ALSA: seq: Add ioctls for client UMP info query and setup ALSA: seq: Print UMP Endpoint and Block information in proc outputs ALSA: seq: Add UMP group filter ALSA: docs: Add MIDI 2.0 documentation Documentation/sound/designs/index.rst | 1 + Documentation/sound/designs/midi-2.0.rst | 351 +++++++ include/linux/usb/midi-v2.h | 94 ++ include/sound/asequencer.h | 4 + include/sound/rawmidi.h | 15 +- include/sound/seq_device.h | 1 + include/sound/seq_kernel.h | 10 + include/sound/ump.h | 175 ++++ include/sound/ump_msg.h | 540 ++++++++++ include/uapi/sound/asequencer.h | 83 +- include/uapi/sound/asound.h | 62 +- sound/core/Kconfig | 13 + sound/core/Makefile | 3 + sound/core/rawmidi.c | 264 +++-- sound/core/rawmidi_compat.c | 4 + sound/core/seq/Kconfig | 14 + sound/core/seq/Makefile | 3 + sound/core/seq/seq_clientmgr.c | 577 +++++++---- sound/core/seq/seq_clientmgr.h | 27 +- sound/core/seq/seq_compat.c | 3 + sound/core/seq/seq_dummy.c | 9 + sound/core/seq/seq_memory.c | 98 +- sound/core/seq/seq_memory.h | 19 +- sound/core/seq/seq_midi.c | 12 +- sound/core/seq/seq_ports.c | 47 +- sound/core/seq/seq_ports.h | 23 +- sound/core/seq/seq_ump_client.c | 464 +++++++++ sound/core/seq/seq_ump_convert.c | 1203 ++++++++++++++++++++++ sound/core/seq/seq_ump_convert.h | 22 + sound/core/seq/seq_virmidi.c | 1 + sound/core/ump.c | 668 ++++++++++++ sound/core/ump_convert.c | 520 ++++++++++ sound/core/ump_convert.h | 43 + sound/usb/Kconfig | 11 + sound/usb/Makefile | 1 + sound/usb/card.c | 12 +- sound/usb/midi.c | 7 +- sound/usb/midi.h | 5 +- sound/usb/midi2.c | 1190 +++++++++++++++++++++ sound/usb/midi2.h | 33 + sound/usb/quirks.c | 8 +- sound/usb/usbaudio.h | 2 + 42 files changed, 6306 insertions(+), 336 deletions(-) create mode 100644 Documentation/sound/designs/midi-2.0.rst create mode 100644 include/linux/usb/midi-v2.h create mode 100644 include/sound/ump.h create mode 100644 include/sound/ump_msg.h create mode 100644 sound/core/seq/seq_ump_client.c create mode 100644 sound/core/seq/seq_ump_convert.c create mode 100644 sound/core/seq/seq_ump_convert.h create mode 100644 sound/core/ump.c create mode 100644 sound/core/ump_convert.c create mode 100644 sound/core/ump_convert.h create mode 100644 sound/usb/midi2.c create mode 100644 sound/usb/midi2.h -- 2.35.3

4 68