Alsa-devel April 2014

alsa-devel@alsa-project.org

113 participants
280 discussions

[alsa-devel] Trouble about Roland UA-11 UA-33 UA-55 and snd-usb-audio module
by FirebUntU 06 Mar '16

06 Mar '16

Hi guys, I write you about support of snd-usb-audio module and a relatively-new gamma of devices from Roland/Edirol: DUO CAPTURE, TRI CAPTURE and QUAD CAPTURE respectively: UA-11, UA-33, UA-55 These aren't not listed in the Alsa db. I have searched a solution for a week and I haven't found a trick to make UA-11 to work under Alsa 1.25.0 then I downloaded the driver for try to patch it and I found these devices is not listed in the tricks table In despair I have played with the switch button called "EXT * **" in the bottom of the unit of UA-11 and magically the device ID is transformed from * 0582:012b to ** 0582:0137 Image: https://dl.dropbox.com/u/32759898/output.jpg (Rear of the UA-11 unit, from the manual) *Before* (Recognized from udev - Unknown from alsa): http://www.alsa-project.org/db/?f=502ee68cf31882ba9ef23525fd66452c34d329e1 *After* (Recognized from udev - Recognized from alsa): http://www.alsa-project.org/db/?f=b2ae3e4331fb3fe613ba71e7aba1ad2e0e6dcd29 In the tricks table header of ALSA the 0582:0137 stay for PM-1000 in /TODO/ statement. I understand the EXT switch, undiscovered in the manual of the DUO CAPTURE is - as the fact - the Advanced Mode. Now the peripherical running both in playback and recording in 16 and 24 bit and without any mixer options in alsamixer. Can you update future releases with this gamma of devices? Awaiting for your positive response :) Thanks. Best regards, Leonardo

9 16

[alsa-devel] Usb audio - unsuported sampling rates
by Gordon Dilan 12 Feb '16

12 Feb '16

Hello, I'm using an usb mic which(according to it's producer should support up to 48kHz sampling rate). The problem is ALSA allows me to use only 16 kHz for this device. I do not want to resample the data, I want to sample it at 48kHz in order to be able to record some high pitch sounds 18-20kHz. I would want to try to do any modifications necessary in order to try support 48kHz, but I'm not sure where to start. Some information: cat /proc/asound/modules ... 1 snd_usb_audio arecord --list-devices **** List of CAPTURE Hardware Devices **** .... card 1: CameraB409241 [USB Camera-B4.09.24.1], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0 when I try to use: arecord -v -D hw:1,0 -f S16_LE -c 4 -r 48000 gigi.wav I get this: Recording WAVE 'gigi.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Channels 4 Warning: rate is not accurate (requested = 48000Hz, got = 16000Hz) please, try the plug plugin Hardware PCM card 1 'USB Camera-B4.09.24.1' device 0 subdevice 0 Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 4 rate : 16000 exact rate : 16000 (16000/1) msbits : 16 buffer_size : 8000 period_size : 2000 period_time : 125000 tstamp_mode : NONE period_step : 1 avail_min : 2000 period_event : 0 start_threshold : 1 stop_threshold : 8000 silence_threshold: 0 silence_size : 0 boundary : 2097152000 appl_ptr : 0 hw_ptr : 0 Any sampling rate I would try higher or lower than 16kHz, I will always get 16000 kHz. Some more information: lsusb Bus 001 Device 007: ID 1415:2000 Nam Tai E&E Products Ltd. or OmniVision Technologies, Inc. Sony Playstation Eye lsusb -t /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci_hcd/2p, 480M |__ Port 1: Dev 2, If 0, Class=hub, Driver=hub/6p, 480M |__ Port 2: Dev 7, If 0, Class=vend., Driver=ov534, 480M |__ Port 2: Dev 7, If 1, Class=audio, Driver=snd-usb-audio, 480M |__ Port 2: Dev 7, If 2, Class=audio, Driver=snd-usb-audio, 480M At the moment I'm looking inside ALSA's source code to try to see from where this limitation of 16000kHz for my device appears, but I have to admit that I'm kind of lost. Any pointers on what direction should I go to try make my desired rate supported would be greatly appreciated! Thank you and best regards, Gordon

3 6

[alsa-devel] [PATCH 0/4] ASoC: fix saif record unwork issue
by Dong Aisheng 16 Jan '16

16 Jan '16

This patch series mainly fixes the saif record unwork issue. The root cause consists of: 1) clk_prepare and clk_enable un-balanced 2) missed setting a proper initial clock rate for saif in dt 3) sgtl5000 dapm widget kcontrol does not work So can not test record on mx28evk. 4) missed setting clkmux mode for saif in dt With this patch series it can fix sgtl5000 widget kcontrol unwork and saif record unwork issue. BTW, just let people konw, i still met a few overruns during record, that's another issue and will be fixed in separte patches later. Patch based on sound-2.6/for-3.6. Dong Aisheng (4): ASoC: mxs-saif: fix clock prepare and enable unbalance issue ASoC: mxs-saif: set a base clock rate for EXTMASTER mode work ASoC: sgtl5000: remove unneeded snd_soc_dapm_new_widgets in probe ARM: mx28evk: add missed clkmux select for saif arch/arm/mach-mxs/mach-mxs.c | 3 +++ sound/soc/codecs/sgtl5000.c | 2 -- sound/soc/mxs/mxs-saif.c | 24 ++++++++++++++++++++++++ 3 files changed, 27 insertions(+), 2 deletions(-)

5 20

[alsa-devel] [V2 PATCH] ALSA: hda - Enable mute/mic-mute LEDs for more Thinkpads with Conexant codec
by Hui Wang 01 Jul '15

01 Jul '15

Most Thinkpad Edge series laptops use conexant codec, so far although the codecs have different minor Vendor Id and minor Subsystem Id, they all belong to the cxt5066 family, this change can make the mute/mic-mute LEDs support more generic among cxt_5066 family. This design refers to the similar solution for the realtek codec ALC269 family in the patch_realtek.c. Cc: Alex Hung <alex.hung(a)canonical.com> Cc: David Henningsson <david.henningsson(a)canonical.com> Signed-off-by: Hui Wang <hui.wang(a)canonical.com> --- sound/pci/hda/patch_conexant.c | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/sound/pci/hda/patch_conexant.c b/sound/pci/hda/patch_conexant.c index c205bb1..1f2717f 100644 --- a/sound/pci/hda/patch_conexant.c +++ b/sound/pci/hda/patch_conexant.c @@ -3244,9 +3244,29 @@ enum { #if IS_ENABLED(CONFIG_THINKPAD_ACPI) #include <linux/thinkpad_acpi.h> +#include <acpi/acpi.h> static int (*led_set_func)(int, bool); +static acpi_status acpi_check_cb(acpi_handle handle, u32 lvl, void *context, + void **rv) +{ + bool *found = context; + *found = true; + return AE_OK; +} + +static bool is_thinkpad(struct hda_codec *codec) +{ + bool found = false; + if (codec->subsystem_id >> 16 != 0x17aa) + return false; + if (ACPI_SUCCESS(acpi_get_devices("LEN0068", acpi_check_cb, &found, NULL)) && found) + return true; + found = false; + return ACPI_SUCCESS(acpi_get_devices("IBM0068", acpi_check_cb, &found, NULL)) && found; +} + static void update_tpacpi_mute_led(void *private_data, int enabled) { struct hda_codec *codec = private_data; @@ -3279,6 +3299,8 @@ static void cxt_fixup_thinkpad_acpi(struct hda_codec *codec, bool removefunc = false; if (action == HDA_FIXUP_ACT_PROBE) { + if (!is_thinkpad(codec)) + return; if (!led_set_func) led_set_func = symbol_request(tpacpi_led_set); if (!led_set_func) { @@ -3494,6 +3516,7 @@ static const struct snd_pci_quirk cxt5066_fixups[] = { SND_PCI_QUIRK(0x17aa, 0x3975, "Lenovo U300s", CXT_FIXUP_STEREO_DMIC), SND_PCI_QUIRK(0x17aa, 0x3977, "Lenovo IdeaPad U310", CXT_FIXUP_STEREO_DMIC), SND_PCI_QUIRK(0x17aa, 0x397b, "Lenovo S205", CXT_FIXUP_STEREO_DMIC), + SND_PCI_QUIRK_VENDOR(0x17aa, "Thinkpad", CXT_FIXUP_THINKPAD_ACPI), SND_PCI_QUIRK(0x1c06, 0x2011, "Lemote A1004", CXT_PINCFG_LEMOTE_A1004), SND_PCI_QUIRK(0x1c06, 0x2012, "Lemote A1205", CXT_PINCFG_LEMOTE_A1205), {} -- 1.8.1.2

7 26

[alsa-devel] SoundBlaster X-fi HD SPDIF fix
by Richard Körber 05 Apr '15

05 Apr '15

Hi! I own a Creative USB SoundBlaster X-fi HD and tried to use its SPDIF optical output. However it didn't work with ALSA out of the box. The reason is that for SPDIF output device #1 must be used. The fix is: In /usr/share/alsa/cards/USB-Audio.conf, change the iec958_device block like this: USB-Audio.pcm.iec958_device { "USB Sound Blaster HD" 1 } Digital output works fine for me after that. BTW, I tried this line in /etc/asound.conf cards.USB-Audio.pcm.iec958_device."USB Sound Blaster HD" 1 but it didn't have any effect. Why was that? Thank you! Regards Richard Körber

2 8

[alsa-devel] [PATCH] add Steinberg UR44 USB Audio Interface support to quirks-table
by Cyrus Harmon 03 Feb '15

03 Feb '15

Signed-off-by: Cyrus Harmon <cyrus(a)bobobeach.com> --- sound/usb/quirks-table.h | 30 ++++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+) diff --git a/sound/usb/quirks-table.h b/sound/usb/quirks-table.h index f652b10..987ca01 100644 --- a/sound/usb/quirks-table.h +++ b/sound/usb/quirks-table.h @@ -436,6 +436,36 @@ YAMAHA_DEVICE(0x105d, NULL), } } }, +{ + USB_DEVICE(0x0499, 0x150e), + .driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) { + /* .vendor_name = "Yamaha", */ + /* .product_name = "Steinberg UR44", */ + .ifnum = QUIRK_ANY_INTERFACE, + .type = QUIRK_COMPOSITE, + .data = (const struct snd_usb_audio_quirk[]) { + { + .ifnum = 1, + .type = QUIRK_AUDIO_STANDARD_INTERFACE + }, + { + .ifnum = 2, + .type = QUIRK_AUDIO_STANDARD_INTERFACE + }, + { + .ifnum = 3, + .type = QUIRK_MIDI_YAMAHA + }, + { + .ifnum = 4, + .type = QUIRK_IGNORE_INTERFACE + }, + { + .ifnum = -1 + } + } + } +}, YAMAHA_DEVICE(0x2000, "DGP-7"), YAMAHA_DEVICE(0x2001, "DGP-5"), YAMAHA_DEVICE(0x2002, NULL), -- 1.8.3.2

5 32

[alsa-devel] [PATCH - ALSA: snd-virtuoso 1/1] Xonar DSX support
by sgiurgiu11＠gmail.com 04 Jan '15

04 Jan '15

From: Sergiu Giurgiu <sgiurgiu11(a)gmail.com> This patch adds support for ASUS - Xonar DSX sound cards. Tested on openSUSE 12.2 with kernel: Linux 3.4.6-2.10-desktop #1 SMP PREEMPT Thu Jul 26 09:36:26 UTC 2012 (641c197) x86_64 x86_64 x86_64 GNU/Linux Works: - play sounds - adjust volume on master channel. - mute . Since Xonar DS uses the same chip, everything that works for DS should work for DSX as well. Thank you, Sergiu Giurgiu. Signed-off-by: Sergiu Giurgiu <sgiurgiu11(a)gmail.com> diff --git a/mirror/sound/pci/oxygen/virtuoso.c b/mirror/sound/pci/oxygen/virtuoso.c index 3d71423..8104eab 100644 --- a/mirror/sound/pci/oxygen/virtuoso.c +++ b/mirror/sound/pci/oxygen/virtuoso.c @@ -52,6 +52,7 @@ static DEFINE_PCI_DEVICE_TABLE(xonar_ids) = { { OXYGEN_PCI_SUBID(0x1043, 0x835d) }, { OXYGEN_PCI_SUBID(0x1043, 0x835e) }, { OXYGEN_PCI_SUBID(0x1043, 0x838e) }, + { OXYGEN_PCI_SUBID(0x1043, 0x8522) }, { OXYGEN_PCI_SUBID_BROKEN_EEPROM }, { } }; diff --git a/mirror/sound/pci/oxygen/xonar_wm87x6.c b/mirror/sound/pci/oxygen/xonar_wm87x6.c index 63cff90..b555b62 100644 --- a/mirror/sound/pci/oxygen/xonar_wm87x6.c +++ b/mirror/sound/pci/oxygen/xonar_wm87x6.c @@ -1255,7 +1255,6 @@ static void dump_wm87x6_registers(struct oxygen *chip, } static const struct oxygen_model model_xonar_ds = { - .shortname = "Xonar DS", .longname = "Asus Virtuoso 66", .chip = "AV200", .init = xonar_ds_init, @@ -1327,6 +1326,11 @@ int __devinit get_xonar_wm87x6_model(struct oxygen *chip, switch (id->subdevice) { case 0x838e: chip->model = model_xonar_ds; + chip->model.shortname = "Xonar DS"; + break; + case 0x8522: + chip->model = model_xonar_ds; + chip->model.shortname = "Xonar DSX"; break; case 0x835e: chip->model = model_xonar_hdav_slim; -- 1.7.10.4

4 5

[alsa-devel] icon utrack pro usb audio interface
by Adrien Plisson 29 Aug '14

29 Aug '14

hello, i just bought an "icon utrack pro" usb audio interface <http://www.icon-global.com/ShowPro.aspx?ID=24>. as expected, this interface is not supported under linux: it is not usb audio class compliant, even the midi port is not class compliant... first, i would like to know if anybody ever managed to use this interface under linux: is there an existing driver ? a hack or patch that would allow the kernel to recognize this interface ? a specific module dedicated to this kind of interface ? i can't find any reference to this interface anywhere on the net... anyway, while searching, i found that its firewire counterpart, the "firexon", has an experimental support on ffado. it seems that the firewire interface uses the bridgeco BeBoB chipset. given that some versions of BeBoB supports both firewire and usb, i suppose (but i may be wrong) that the "utrack pro" is also based on BeBoB. is there any other BeBoB based usb interface supported under linux ? finally, i would proudly help the development of a specific driver for this interface: if anyone wants me to test some piece of code, or wants some information on this interface, don't hesitate to contact me. i am also a software developper, so i could help writing a module, but i first need to learn more about the alsa code base (actually, i don't know where to start...). thanks a lot, and have a nice day ! -- rien

3 3

[alsa-devel] [PATCH 1/2] usbtv: split core and video implementation
by Federico Simoncelli 19 Aug '14

19 Aug '14

From: Federico Simoncelli <fsimonce(a)redhat.com> Signed-off-by: Federico Simoncelli <fsimonce(a)redhat.com> Reviewed-by: Lubomir Rintel <lkundrak(a)v3.sk> --- drivers/media/usb/usbtv/Makefile | 3 + drivers/media/usb/usbtv/usbtv-core.c | 136 +++++++++++++++++ drivers/media/usb/usbtv/{usbtv.c => usbtv-video.c} | 163 ++------------------- drivers/media/usb/usbtv/usbtv.h | 98 +++++++++++++ 4 files changed, 246 insertions(+), 154 deletions(-) create mode 100644 drivers/media/usb/usbtv/usbtv-core.c rename drivers/media/usb/usbtv/{usbtv.c => usbtv-video.c} (82%) create mode 100644 drivers/media/usb/usbtv/usbtv.h diff --git a/drivers/media/usb/usbtv/Makefile b/drivers/media/usb/usbtv/Makefile index 28b872f..775316a 100644 --- a/drivers/media/usb/usbtv/Makefile +++ b/drivers/media/usb/usbtv/Makefile @@ -1 +1,4 @@ +usbtv-y := usbtv-core.o \ + usbtv-video.o + obj-$(CONFIG_VIDEO_USBTV) += usbtv.o diff --git a/drivers/media/usb/usbtv/usbtv-core.c b/drivers/media/usb/usbtv/usbtv-core.c new file mode 100644 index 0000000..e89e48b --- /dev/null +++ b/drivers/media/usb/usbtv/usbtv-core.c @@ -0,0 +1,136 @@ +/* + * Fushicai USBTV007 Video Grabber Driver + * + * Product web site: + * http://www.fushicai.com/products_detail/&productId=d05449ee-b690-42f9-a661-… + * + * Following LWN articles were very useful in construction of this driver: + * Video4Linux2 API series: http://lwn.net/Articles/203924/ + * videobuf2 API explanation: http://lwn.net/Articles/447435/ + * Thanks go to Jonathan Corbet for providing this quality documentation. + * He is awesome. + * + * Copyright (c) 2013 Lubomir Rintel + * All rights reserved. + * No physical hardware was harmed running Windows during the + * reverse-engineering activity + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. The name of the author may not be used to endorse or promote products + * derived from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL"). + */ + +#include <linux/module.h> + +#include "usbtv.h" + +int usbtv_set_regs(struct usbtv *usbtv, const u16 regs[][2], int size) +{ + int ret; + int pipe = usb_rcvctrlpipe(usbtv->udev, 0); + int i; + + for (i = 0; i < size; i++) { + u16 index = regs[i][0]; + u16 value = regs[i][1]; + + ret = usb_control_msg(usbtv->udev, pipe, USBTV_REQUEST_REG, + USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE, + value, index, NULL, 0, 0); + if (ret < 0) + return ret; + } + + return 0; +} + +static int usbtv_probe(struct usb_interface *intf, + const struct usb_device_id *id) +{ + int ret; + int size; + struct device *dev = &intf->dev; + struct usbtv *usbtv; + + /* Checks that the device is what we think it is. */ + if (intf->num_altsetting != 2) + return -ENODEV; + if (intf->altsetting[1].desc.bNumEndpoints != 4) + return -ENODEV; + + /* Packet size is split into 11 bits of base size and count of + * extra multiplies of it.*/ + size = usb_endpoint_maxp(&intf->altsetting[1].endpoint[0].desc); + size = (size & 0x07ff) * (((size & 0x1800) >> 11) + 1); + + /* Device structure */ + usbtv = kzalloc(sizeof(struct usbtv), GFP_KERNEL); + if (usbtv == NULL) + return -ENOMEM; + usbtv->dev = dev; + usbtv->udev = usb_get_dev(interface_to_usbdev(intf)); + + usbtv->iso_size = size; + + usb_set_intfdata(intf, usbtv); + + ret = usbtv_video_init(usbtv); + if (ret < 0) + goto usbtv_video_fail; + + /* for simplicity we exploit the v4l2_device reference counting */ + v4l2_device_get(&usbtv->v4l2_dev); + + dev_info(dev, "Fushicai USBTV007 Video Grabber\n"); + return 0; + +usbtv_video_fail: + kfree(usbtv); + + return ret; +} + +static void usbtv_disconnect(struct usb_interface *intf) +{ + struct usbtv *usbtv = usb_get_intfdata(intf); + usb_set_intfdata(intf, NULL); + + if (!usbtv) + return; + + usbtv_video_free(usbtv); + + usb_put_dev(usbtv->udev); + usbtv->udev = NULL; + + /* the usbtv structure will be deallocated when v4l2 will be + done using it */ + v4l2_device_put(&usbtv->v4l2_dev); +} + +struct usb_device_id usbtv_id_table[] = { + { USB_DEVICE(0x1b71, 0x3002) }, + {} +}; +MODULE_DEVICE_TABLE(usb, usbtv_id_table); + +MODULE_AUTHOR("Lubomir Rintel"); +MODULE_DESCRIPTION("Fushicai USBTV007 Video Grabber Driver"); +MODULE_LICENSE("Dual BSD/GPL"); + +struct usb_driver usbtv_usb_driver = { + .name = "usbtv", + .id_table = usbtv_id_table, + .probe = usbtv_probe, + .disconnect = usbtv_disconnect, +}; + +module_usb_driver(usbtv_usb_driver); diff --git a/drivers/media/usb/usbtv/usbtv.c b/drivers/media/usb/usbtv/usbtv-video.c similarity index 82% rename from drivers/media/usb/usbtv/usbtv.c rename to drivers/media/usb/usbtv/usbtv-video.c index 6222a4a..496bc2e 100644 --- a/drivers/media/usb/usbtv/usbtv.c +++ b/drivers/media/usb/usbtv/usbtv-video.c @@ -28,45 +28,10 @@ * GNU General Public License ("GPL"). */ -#include <linux/init.h> -#include <linux/list.h> -#include <linux/module.h> -#include <linux/slab.h> -#include <linux/usb.h> -#include <linux/videodev2.h> - -#include <media/v4l2-device.h> #include <media/v4l2-ioctl.h> #include <media/videobuf2-core.h> -#include <media/videobuf2-vmalloc.h> - -/* Hardware. */ -#define USBTV_VIDEO_ENDP 0x81 -#define USBTV_BASE 0xc000 -#define USBTV_REQUEST_REG 12 - -/* Number of concurrent isochronous urbs submitted. - * Higher numbers was seen to overly saturate the USB bus. */ -#define USBTV_ISOC_TRANSFERS 16 -#define USBTV_ISOC_PACKETS 8 - -#define USBTV_CHUNK_SIZE 256 -#define USBTV_CHUNK 240 - -/* Chunk header. */ -#define USBTV_MAGIC_OK(chunk) ((be32_to_cpu(chunk[0]) & 0xff000000) \ - == 0x88000000) -#define USBTV_FRAME_ID(chunk) ((be32_to_cpu(chunk[0]) & 0x00ff0000) >> 16) -#define USBTV_ODD(chunk) ((be32_to_cpu(chunk[0]) & 0x0000f000) >> 15) -#define USBTV_CHUNK_NO(chunk) (be32_to_cpu(chunk[0]) & 0x00000fff) - -#define USBTV_TV_STD (V4L2_STD_525_60 | V4L2_STD_PAL) - -/* parameters for supported TV norms */ -struct usbtv_norm_params { - v4l2_std_id norm; - int cap_width, cap_height; -}; + +#include "usbtv.h" static struct usbtv_norm_params norm_params[] = { { @@ -81,43 +46,6 @@ static struct usbtv_norm_params norm_params[] = { } }; -/* A single videobuf2 frame buffer. */ -struct usbtv_buf { - struct vb2_buffer vb; - struct list_head list; -}; - -/* Per-device structure. */ -struct usbtv { - struct device *dev; - struct usb_device *udev; - struct v4l2_device v4l2_dev; - struct video_device vdev; - struct vb2_queue vb2q; - struct mutex v4l2_lock; - struct mutex vb2q_lock; - - /* List of videobuf2 buffers protected by a lock. */ - spinlock_t buflock; - struct list_head bufs; - - /* Number of currently processed frame, useful find - * out when a new one begins. */ - u32 frame_id; - int chunks_done; - - enum { - USBTV_COMPOSITE_INPUT, - USBTV_SVIDEO_INPUT, - } input; - v4l2_std_id norm; - int width, height; - int n_chunks; - int iso_size; - unsigned int sequence; - struct urb *isoc_urbs[USBTV_ISOC_TRANSFERS]; -}; - static int usbtv_configure_for_norm(struct usbtv *usbtv, v4l2_std_id norm) { int i, ret = 0; @@ -142,26 +70,6 @@ static int usbtv_configure_for_norm(struct usbtv *usbtv, v4l2_std_id norm) return ret; } -static int usbtv_set_regs(struct usbtv *usbtv, const u16 regs[][2], int size) -{ - int ret; - int pipe = usb_rcvctrlpipe(usbtv->udev, 0); - int i; - - for (i = 0; i < size; i++) { - u16 index = regs[i][0]; - u16 value = regs[i][1]; - - ret = usb_control_msg(usbtv->udev, pipe, USBTV_REQUEST_REG, - USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE, - value, index, NULL, 0, 0); - if (ret < 0) - return ret; - } - - return 0; -} - static int usbtv_select_input(struct usbtv *usbtv, int input) { int ret; @@ -560,12 +468,6 @@ start_fail: return ret; } -struct usb_device_id usbtv_id_table[] = { - { USB_DEVICE(0x1b71, 0x3002) }, - {} -}; -MODULE_DEVICE_TABLE(usb, usbtv_id_table); - static int usbtv_querycap(struct file *file, void *priv, struct v4l2_capability *cap) { @@ -759,33 +661,9 @@ static void usbtv_release(struct v4l2_device *v4l2_dev) kfree(usbtv); } -static int usbtv_probe(struct usb_interface *intf, - const struct usb_device_id *id) +int usbtv_video_init(struct usbtv *usbtv) { int ret; - int size; - struct device *dev = &intf->dev; - struct usbtv *usbtv; - - /* Checks that the device is what we think it is. */ - if (intf->num_altsetting != 2) - return -ENODEV; - if (intf->altsetting[1].desc.bNumEndpoints != 4) - return -ENODEV; - - /* Packet size is split into 11 bits of base size and count of - * extra multiplies of it.*/ - size = usb_endpoint_maxp(&intf->altsetting[1].endpoint[0].desc); - size = (size & 0x07ff) * (((size & 0x1800) >> 11) + 1); - - /* Device structure */ - usbtv = kzalloc(sizeof(struct usbtv), GFP_KERNEL); - if (usbtv == NULL) - return -ENOMEM; - usbtv->dev = dev; - usbtv->udev = usb_get_dev(interface_to_usbdev(intf)); - - usbtv->iso_size = size; (void)usbtv_configure_for_norm(usbtv, V4L2_STD_525_60); @@ -805,20 +683,18 @@ static int usbtv_probe(struct usb_interface *intf, usbtv->vb2q.lock = &usbtv->vb2q_lock; ret = vb2_queue_init(&usbtv->vb2q); if (ret < 0) { - dev_warn(dev, "Could not initialize videobuf2 queue\n"); - goto usbtv_fail; + dev_warn(usbtv->dev, "Could not initialize videobuf2 queue\n"); + return ret; } /* v4l2 structure */ usbtv->v4l2_dev.release = usbtv_release; - ret = v4l2_device_register(dev, &usbtv->v4l2_dev); + ret = v4l2_device_register(usbtv->dev, &usbtv->v4l2_dev); if (ret < 0) { - dev_warn(dev, "Could not register v4l2 device\n"); + dev_warn(usbtv->dev, "Could not register v4l2 device\n"); goto v4l2_fail; } - usb_set_intfdata(intf, usbtv); - /* Video structure */ strlcpy(usbtv->vdev.name, "usbtv", sizeof(usbtv->vdev.name)); usbtv->vdev.v4l2_dev = &usbtv->v4l2_dev; @@ -832,52 +708,31 @@ static int usbtv_probe(struct usb_interface *intf, video_set_drvdata(&usbtv->vdev, usbtv); ret = video_register_device(&usbtv->vdev, VFL_TYPE_GRABBER, -1); if (ret < 0) { - dev_warn(dev, "Could not register video device\n"); + dev_warn(usbtv->dev, "Could not register video device\n"); goto vdev_fail; } - dev_info(dev, "Fushicai USBTV007 Video Grabber\n"); return 0; vdev_fail: v4l2_device_unregister(&usbtv->v4l2_dev); v4l2_fail: vb2_queue_release(&usbtv->vb2q); -usbtv_fail: - kfree(usbtv); return ret; } -static void usbtv_disconnect(struct usb_interface *intf) +void usbtv_video_free(struct usbtv *usbtv) { - struct usbtv *usbtv = usb_get_intfdata(intf); - mutex_lock(&usbtv->vb2q_lock); mutex_lock(&usbtv->v4l2_lock); usbtv_stop(usbtv); - usb_set_intfdata(intf, NULL); video_unregister_device(&usbtv->vdev); v4l2_device_disconnect(&usbtv->v4l2_dev); - usb_put_dev(usbtv->udev); - usbtv->udev = NULL; mutex_unlock(&usbtv->v4l2_lock); mutex_unlock(&usbtv->vb2q_lock); v4l2_device_put(&usbtv->v4l2_dev); } - -MODULE_AUTHOR("Lubomir Rintel"); -MODULE_DESCRIPTION("Fushicai USBTV007 Video Grabber Driver"); -MODULE_LICENSE("Dual BSD/GPL"); - -struct usb_driver usbtv_usb_driver = { - .name = "usbtv", - .id_table = usbtv_id_table, - .probe = usbtv_probe, - .disconnect = usbtv_disconnect, -}; - -module_usb_driver(usbtv_usb_driver); diff --git a/drivers/media/usb/usbtv/usbtv.h b/drivers/media/usb/usbtv/usbtv.h new file mode 100644 index 0000000..536343d --- /dev/null +++ b/drivers/media/usb/usbtv/usbtv.h @@ -0,0 +1,98 @@ +/* + * Fushicai USBTV007 Video Grabber Driver + * + * Copyright (c) 2013 Lubomir Rintel + * All rights reserved. + * No physical hardware was harmed running Windows during the + * reverse-engineering activity + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. The name of the author may not be used to endorse or promote products + * derived from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL"). + */ + +#include <linux/slab.h> +#include <linux/usb.h> + +#include <media/v4l2-device.h> +#include <media/videobuf2-vmalloc.h> + +/* Hardware. */ +#define USBTV_VIDEO_ENDP 0x81 +#define USBTV_BASE 0xc000 +#define USBTV_REQUEST_REG 12 + +/* Number of concurrent isochronous urbs submitted. + * Higher numbers was seen to overly saturate the USB bus. */ +#define USBTV_ISOC_TRANSFERS 16 +#define USBTV_ISOC_PACKETS 8 + +#define USBTV_CHUNK_SIZE 256 +#define USBTV_CHUNK 240 + +/* Chunk header. */ +#define USBTV_MAGIC_OK(chunk) ((be32_to_cpu(chunk[0]) & 0xff000000) \ + == 0x88000000) +#define USBTV_FRAME_ID(chunk) ((be32_to_cpu(chunk[0]) & 0x00ff0000) >> 16) +#define USBTV_ODD(chunk) ((be32_to_cpu(chunk[0]) & 0x0000f000) >> 15) +#define USBTV_CHUNK_NO(chunk) (be32_to_cpu(chunk[0]) & 0x00000fff) + +#define USBTV_TV_STD (V4L2_STD_525_60 | V4L2_STD_PAL) + +/* parameters for supported TV norms */ +struct usbtv_norm_params { + v4l2_std_id norm; + int cap_width, cap_height; +}; + +/* A single videobuf2 frame buffer. */ +struct usbtv_buf { + struct vb2_buffer vb; + struct list_head list; +}; + +/* Per-device structure. */ +struct usbtv { + struct device *dev; + struct usb_device *udev; + + /* video */ + struct v4l2_device v4l2_dev; + struct video_device vdev; + struct vb2_queue vb2q; + struct mutex v4l2_lock; + struct mutex vb2q_lock; + + /* List of videobuf2 buffers protected by a lock. */ + spinlock_t buflock; + struct list_head bufs; + + /* Number of currently processed frame, useful find + * out when a new one begins. */ + u32 frame_id; + int chunks_done; + + enum { + USBTV_COMPOSITE_INPUT, + USBTV_SVIDEO_INPUT, + } input; + v4l2_std_id norm; + int width, height; + int n_chunks; + int iso_size; + unsigned int sequence; + struct urb *isoc_urbs[USBTV_ISOC_TRANSFERS]; +}; + +int usbtv_set_regs(struct usbtv *usbtv, const u16 regs[][2], int size); + +int usbtv_video_init(struct usbtv *usbtv); +void usbtv_video_free(struct usbtv *usbtv); -- 1.8.4.2

4 5

[alsa-devel] [PATCH] ALSA: hda - initialize audio InfoFrame to be all zero
by mengdong.lin＠intel.com 23 Jul '14

23 Jul '14

From: Mengdong Lin <mengdong.lin(a)intel.com> This patch initialized the local audio InfoFrame variable 'ai' to be all zero, thus the data bytes will indicate "Refer to Stream Header" by default. Signed-off-by: Mengdong Lin <mengdong.lin(a)intel.com> diff --git a/sound/pci/hda/patch_hdmi.c b/sound/pci/hda/patch_hdmi.c index 5ef9503..3ab7063 100644 --- a/sound/pci/hda/patch_hdmi.c +++ b/sound/pci/hda/patch_hdmi.c @@ -1062,6 +1062,7 @@ static void hdmi_pin_setup_infoframe(struct hda_codec *codec, { union audio_infoframe ai; + memset(&ai, 0, sizeof(ai)); if (conn_type == 0) { /* HDMI */ struct hdmi_audio_infoframe *hdmi_ai = &ai.hdmi; -- 1.8.1.2

4 5

Jump to page:

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

Alsa-devel April 2014