December 2021 - Alsa-devel - mailman.alsa-project.org

[PATCH 0/2] sound/soc: Use platform_get_irq() to fetch IRQ's
by Lad Prabhakar 21 Dec '21

21 Dec '21

Hi All, This patch series aims to drop using platform_get_resource() for IRQ types in preparation for removal of static setup of IRQ resource from DT core code. Dropping usage of platform_get_resource() was agreed based on the discussion [0]. [0] https://patchwork.kernel.org/project/linux-renesas-soc/ patch/20211209001056.29774-1-prabhakar.mahadev-lad.rj(a)bp.renesas.com/ Note: I have just build tested the patches. Cheers, Prabhakar Lad Prabhakar (2): ASoC: xlnx: Use platform_get_irq() to get the interrupt ASoC: bcm: Use platform_get_irq() to get the interrupt sound/soc/bcm/bcm63xx-i2s.h | 1 - sound/soc/bcm/bcm63xx-pcm-whistler.c | 12 +++++------- sound/soc/xilinx/xlnx_spdif.c | 10 +++------- 3 files changed, 8 insertions(+), 15 deletions(-) -- 2.17.1

3 5

[PATCH v1] dt-bindings: sound: tegra-audio-rt5677: Correct example
by Dmitry Osipenko 21 Dec '21

21 Dec '21

Remove non-existent properties from the example of the binding. These properties were borrower from the old txt binding, but they were never used in practice and aren't documented in the new binding. They aren't reported by the binding checker because dtschema needs extra patch that hasn't been upstreamed yet to make unevaluatedProperties work properly. Signed-off-by: Dmitry Osipenko <digetx(a)gmail.com> --- .../devicetree/bindings/sound/nvidia,tegra-audio-rt5677.yaml | 3 --- 1 file changed, 3 deletions(-) diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5677.yaml b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5677.yaml index 03ff691c26c8..a49997d6028b 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5677.yaml +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5677.yaml @@ -92,9 +92,6 @@ examples: nvidia,audio-codec = <&rt5677>; nvidia,hp-det-gpios = <&gpio 143 0>; - nvidia,mic-present-gpios = <&gpio 132 1>; - nvidia,hp-en-gpios = <&rt5677 1 0>; - nvidia,dmic-clk-en-gpios = <&rt5677 2 1>; clocks = <&clk 216>, <&clk 217>, -- 2.33.1

3 4

[PATCH 1/3] ASoC: SOF: AMD: simplify return status handling
by Ajit Kumar Pandey 21 Dec '21

21 Dec '21

From: Pierre-Louis Bossart <pierre-louis.bossart(a)linux.intel.com> cppcheck warning: sound/soc/sof/amd/acp.c:222:9: warning: Identical condition and return expression 'ret', return value is always 0 [identicalConditionAfterEarlyExit] return ret; ^ sound/soc/sof/amd/acp.c:213:6: note: If condition 'ret' is true, the function will return/exit if (ret) ^ sound/soc/sof/amd/acp.c:222:9: note: Returning identical expression 'ret' return ret; ^ Just return 0; on success. Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart(a)linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan(a)intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi(a)linux.intel.com> --- sound/soc/sof/amd/acp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/sof/amd/acp.c b/sound/soc/sof/amd/acp.c index 4c5550e8d364..fe9b7dc5bc86 100644 --- a/sound/soc/sof/amd/acp.c +++ b/sound/soc/sof/amd/acp.c @@ -219,7 +219,7 @@ int configure_and_run_sha_dma(struct acp_dev_data *adata, void *image_addr, return -EINVAL; } - return ret; + return 0; } int acp_dma_status(struct acp_dev_data *adata, unsigned char ch) -- 2.25.1

2 5

[PATCH v2 0/3] Fix Tegra194 HDA regression
by Sameer Pujar 21 Dec '21

21 Dec '21

HDA probe failure is observed on Tegra194 based platforms and this happens due to reset failure. This series fixes the problem by skipping the failing reset and DT bindings are updated accordingly. Changelog ========= v1 -> v2: --------- * Updated HDA driver patch to skip the failing reset instead of skipping resets in general for BPMP devices as per comment from Dmitry. * Used a better strucure name for SoC data as per comment from Thierry. * Dropped 'Fixes' tag in binding doc patch as per comment from Dmitry. Sameer Pujar (3): ALSA: hda/tegra: Fix Tegra194 HDA reset failure dt-bindings: sound: tegra: Update HDA resets arm64: tegra: Remove non existent Tegra194 reset .../bindings/sound/nvidia,tegra30-hda.yaml | 13 ++- arch/arm64/boot/dts/nvidia/tegra194.dtsi | 5 +- sound/pci/hda/hda_tegra.c | 96 +++++++++++++++++++--- 3 files changed, 97 insertions(+), 17 deletions(-) -- 2.7.4

2 7

[PATCH] ASoC: mediatek: mt8195-mt6359: reduce log verbosity in probe()
by Tzung-Bi Shih 21 Dec '21

21 Dec '21

Eliminates error messages if snd_soc_register_card() failed. Kernel emits messages if device probe error anyway. This is mainly for removing the following error messages during boot. >>> snd_soc_register_card fail -517 Signed-off-by: Tzung-Bi Shih <tzungbi(a)google.com> --- sound/soc/mediatek/mt8195/mt8195-mt6359-rt1011-rt5682.c | 2 -- sound/soc/mediatek/mt8195/mt8195-mt6359-rt1019-rt5682.c | 2 -- 2 files changed, 4 deletions(-) diff --git a/sound/soc/mediatek/mt8195/mt8195-mt6359-rt1011-rt5682.c b/sound/soc/mediatek/mt8195/mt8195-mt6359-rt1011-rt5682.c index 5cdbfaafd479..9cf907c49ea8 100644 --- a/sound/soc/mediatek/mt8195/mt8195-mt6359-rt1011-rt5682.c +++ b/sound/soc/mediatek/mt8195/mt8195-mt6359-rt1011-rt5682.c @@ -1114,8 +1114,6 @@ static int mt8195_mt6359_rt1011_rt5682_dev_probe(struct platform_device *pdev) ret = devm_snd_soc_register_card(&pdev->dev, card); if (ret) { - dev_err(&pdev->dev, "%s snd_soc_register_card fail %d\n", - __func__, ret); of_node_put(priv->hdmi_node); of_node_put(priv->dp_node); of_node_put(priv->platform_node); diff --git a/sound/soc/mediatek/mt8195/mt8195-mt6359-rt1019-rt5682.c b/sound/soc/mediatek/mt8195/mt8195-mt6359-rt1019-rt5682.c index fa50a31e9718..fdd444138728 100644 --- a/sound/soc/mediatek/mt8195/mt8195-mt6359-rt1019-rt5682.c +++ b/sound/soc/mediatek/mt8195/mt8195-mt6359-rt1019-rt5682.c @@ -1358,8 +1358,6 @@ static int mt8195_mt6359_rt1019_rt5682_dev_probe(struct platform_device *pdev) ret = devm_snd_soc_register_card(&pdev->dev, card); if (ret) { - dev_err(&pdev->dev, "%s snd_soc_register_card fail %d\n", - __func__, ret); of_node_put(priv->hdmi_node); of_node_put(priv->dp_node); of_node_put(priv->platform_node); -- 2.34.1.173.g76aa8bc2d0-goog

2 1

[PATCH v7 1/2] dt-bindings: sound: tlv320adc3xxx: New codec driver
by Ricard Wanderlof 21 Dec '21

21 Dec '21

DT bindings for Texas Instruments TLV320ADC3001 and TLV320ADC3101 audio ADCs. Change-Id: I94e948892f47df7acb5cffc007d4678b37a96bc8 Signed-off-by: Ricard Wanderlof <ricardw(a)axis.com> --- .../bindings/sound/ti,tlv320adc3xxx.yaml | 137 ++++++++++++++++++ include/dt-bindings/sound/tlv320adc3xxx.h | 28 ++++ 2 files changed, 165 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/ti,tlv320adc3xxx.yaml create mode 100644 include/dt-bindings/sound/tlv320adc3xxx.h diff --git a/Documentation/devicetree/bindings/sound/ti,tlv320adc3xxx.yaml b/Documentation/devicetree/bindings/sound/ti,tlv320adc3xxx.yaml new file mode 100644 index 000000000000..83936f594d1a --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ti,tlv320adc3xxx.yaml @@ -0,0 +1,137 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/ti,tlv320adc3xxx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments TLV320ADC3001/TLV320ADC3101 Stereo ADC + +maintainers: + - Ricard Wanderlof <ricardw(a)axis.com> + +description: | + Texas Instruments TLV320ADC3001 and TLV320ADC3101 Stereo ADC + https://www.ti.com/product/TLV320ADC3001 + https://www.ti.com/product/TLV320ADC3101 + +properties: + compatible: + enum: + - ti,tlv320adc3001 + - ti,tlv320adc3101 + + reg: + maxItems: 1 + description: I2C address + + '#sound-dai-cells': + const: 0 + + '#gpio-cells': + const: 2 + + gpio-controller: true + + reset-gpios: + maxItems: 1 + description: GPIO pin used for codec reset (RESET pin) + + clocks: + maxItems: 1 + description: Master clock (MCLK) + + ti,dmdin-gpio1: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # ADC3XXX_GPIO_DISABLED - I/O buffers powered down and not used + - 1 # ADC3XXX_GPIO_INPUT - Various non-GPIO input functions + - 2 # ADC3XXX_GPIO_GPI - General purpose input + - 3 # ADC3XXX_GPIO_GPO - General purpose output + - 4 # ADC3XXX_GPIO_CLKOUT - Clock source set in CLKOUT_MUX reg + - 5 # ADC3XXX_GPIO_INT1 - INT1 output + - 6 # ADC3XXX_GPIO_SECONDARY_BCLK - Codec interface secondary BCLK + - 7 # ADC3XXX_GPIO_SECONDARY_WCLK - Codec interface secondary WCLK + default: 0 + description: | + Configuration for DMDIN/GPIO1 pin. + + When ADC3XXX_GPIO_GPO is configured, this causes corresponding the + ALSA control "GPIOx Output" to appear, as a switch control. + + ti,dmclk-gpio2: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # ADC3XXX_GPIO_DISABLED - I/O buffers powered down and not used + - 1 # ADC3XXX_GPIO_INPUT - Various non-GPIO input functions + - 2 # ADC3XXX_GPIO_GPI - General purpose input + - 3 # ADC3XXX_GPIO_GPO - General purpose output + - 4 # ADC3XXX_GPIO_CLKOUT - Clock source set in CLKOUT_MUX reg + - 5 # ADC3XXX_GPIO_INT1 - INT1 output + - 6 # ADC3XXX_GPIO_SECONDARY_BCLK - Codec interface secondary BCLK + - 7 # ADC3XXX_GPIO_SECONDARY_WCLK - Codec interface secondary WCLK + default: 0 + description: | + Configuration for DMCLK/GPIO2 pin. + + When ADC3XXX_GPIO_GPO is configured, this causes corresponding the + ALSA control "GPIOx Output" to appear, as a switch control. + + Note that there is currently no support for reading the GPIO pins as + inputs. + + ti,micbias1-vg: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # ADC3XXX_MICBIAS_OFF - Mic bias is powered down + - 1 # ADC3XXX_MICBIAS_2_0V - Mic bias is set to 2.0V + - 2 # ADC3XXX_MICBIAS_2_5V - Mic bias is set to 2.5V + - 3 # ADC3XXX_MICBIAS_AVDD - Mic bias is same as AVDD supply + default: 0 + description: | + Mic bias voltage output on MICBIAS1 pin + + ti,micbias2-vg: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # ADC3XXX_MICBIAS_OFF - Mic bias is powered down + - 1 # ADC3XXX_MICBIAS_2_0V - Mic bias is set to 2.0V + - 2 # ADC3XXX_MICBIAS_2_5V - Mic bias is set to 2.5V + - 3 # ADC3XXX_MICBIAS_AVDD - Mic bias is same as AVDD supply + default: 0 + description: | + Mic bias voltage output on MICBIAS2 pin + +required: + - compatible + - reg + - clocks + +additionalProperties: false + +examples: + - | + + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/sound/tlv320adc3xxx.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + tlv320adc3101: audio-codec@18 { + compatible = "ti,tlv320adc3101"; + reg = <0x18>; + reset-gpios = <&gpio_pc 3 GPIO_ACTIVE_LOW>; + clocks = <&audio_mclk>; + gpio-controller; + #gpio-cells = <2>; + ti,dmdin-gpio1 = <ADC3XXX_GPIO_GPO>; + ti,micbias1-vg = <ADC3XXX_MICBIAS_AVDD>; + }; + }; + + audio_mclk: clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24576000>; + }; +... diff --git a/include/dt-bindings/sound/tlv320adc3xxx.h b/include/dt-bindings/sound/tlv320adc3xxx.h new file mode 100644 index 000000000000..ec988439da20 --- /dev/null +++ b/include/dt-bindings/sound/tlv320adc3xxx.h @@ -0,0 +1,28 @@ +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ +/* + * Devicetree bindings definitions for tlv320adc3xxx driver. + * + * Copyright (C) 2021 Axis Communications AB + */ +#ifndef __DT_TLV320ADC3XXX_H +#define __DT_TLV320ADC3XXX_H + +#define ADC3XXX_GPIO_DISABLED 0 /* I/O buffers powered down */ +#define ADC3XXX_GPIO_INPUT 1 /* Various non-GPIO inputs */ +#define ADC3XXX_GPIO_GPI 2 /* General purpose input */ +#define ADC3XXX_GPIO_GPO 3 /* General purpose output */ +#define ADC3XXX_GPIO_CLKOUT 4 /* Source set in reg. CLKOUT_MUX */ +#define ADC3XXX_GPIO_INT1 5 /* INT1 output */ +#define ADC3XXX_GPIO_INT2 6 /* INT2 output */ +/* value 7 is reserved */ +#define ADC3XXX_GPIO_SECONDARY_BCLK 8 /* Codec interface secondary BCLK */ +#define ADC3XXX_GPIO_SECONDARY_WCLK 9 /* Codec interface secondary WCLK */ +#define ADC3XXX_GPIO_ADC_MOD_CLK 10 /* Clock output for digital mics */ +/* values 11-15 reserved */ + +#define ADC3XXX_MICBIAS_OFF 0 /* Micbias pin powered off */ +#define ADC3XXX_MICBIAS_2_0V 1 /* Micbias pin set to 2.0V */ +#define ADC3XXX_MICBIAS_2_5V 2 /* Micbias pin set to 2.5V */ +#define ADC3XXX_MICBIAS_AVDD 3 /* Use AVDD voltage for micbias pin */ + +#endif /* __DT_TLV320ADC3XXX_H */ -- 2.20.1 -- Ricard Wolf Wanderlof ricardw(at)axis.com Axis Communications AB, Lund, Sweden www.axis.com Phone +46 46 272 2016 Fax +46 46 13 61 30

2 1

[PATCH v7 2/2] ASoC: codec: tlv320adc3xxx: New codec driver
by Ricard Wanderlof 21 Dec '21

21 Dec '21

New codec driver for Texas Instruments TLV320ADC3001 and TLV320ADC3101 audio ADCs. Signed-off-by: Ricard Wanderlof <ricardw(a)axis.com> --- sound/soc/codecs/Kconfig | 8 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/tlv320adc3xxx.c | 1311 ++++++++++++++++++++++++++++++ 3 files changed, 1321 insertions(+) create mode 100644 sound/soc/codecs/tlv320adc3xxx.c diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index c033ee7d82e4..22836ca9b478 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -220,6 +220,7 @@ config SND_SOC_ALL_CODECS imply SND_SOC_TDA7419 imply SND_SOC_TFA9879 imply SND_SOC_TFA989X + imply SND_SOC_TLV320ADC3XXX imply SND_SOC_TLV320ADCX140 imply SND_SOC_TLV320AIC23_I2C imply SND_SOC_TLV320AIC23_SPI @@ -1496,6 +1497,13 @@ config SND_SOC_TFA989X Note that the driver currently bypasses the built-in "CoolFlux DSP" and does not support (hardware) volume control. +config SND_SOC_TLV320ADC3XXX + tristate "Texas Instruments TLV320ADC3001/3101 audio ADC" + depends on I2C + help + Enable support for Texas Instruments TLV320ADC3001 and TLV320ADC3101 + ADCs. + config SND_SOC_TLV320AIC23 tristate diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 485eee75502b..24bc6b34ba2f 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -239,6 +239,7 @@ snd-soc-tda7419-objs := tda7419.o snd-soc-tas2770-objs := tas2770.o snd-soc-tfa9879-objs := tfa9879.o snd-soc-tfa989x-objs := tfa989x.o +snd-soc-tlv320adc3xxx-objs := tlv320adc3xxx.o snd-soc-tlv320aic23-objs := tlv320aic23.o snd-soc-tlv320aic23-i2c-objs := tlv320aic23-i2c.o snd-soc-tlv320aic23-spi-objs := tlv320aic23-spi.o @@ -574,6 +575,7 @@ obj-$(CONFIG_SND_SOC_TDA7419) += snd-soc-tda7419.o obj-$(CONFIG_SND_SOC_TAS2770) += snd-soc-tas2770.o obj-$(CONFIG_SND_SOC_TFA9879) += snd-soc-tfa9879.o obj-$(CONFIG_SND_SOC_TFA989X) += snd-soc-tfa989x.o +obj-$(CONFIG_SND_SOC_TLV320ADC3XXX) += snd-soc-tlv320adc3xxx.o obj-$(CONFIG_SND_SOC_TLV320AIC23) += snd-soc-tlv320aic23.o obj-$(CONFIG_SND_SOC_TLV320AIC23_I2C) += snd-soc-tlv320aic23-i2c.o obj-$(CONFIG_SND_SOC_TLV320AIC23_SPI) += snd-soc-tlv320aic23-spi.o diff --git a/sound/soc/codecs/tlv320adc3xxx.c b/sound/soc/codecs/tlv320adc3xxx.c new file mode 100644 index 000000000000..a683bda7eb36 --- /dev/null +++ b/sound/soc/codecs/tlv320adc3xxx.c @@ -0,0 +1,1311 @@ +// SPDX-License-Identifier: GPL-2.0-only +// +// Based on sound/soc/codecs/tlv320aic3x.c by Vladimir Barinov +// +// Copyright (C) 2010 Mistral Solutions Pvt Ltd. +// Author: Shahina Shaik <shahina.s(a)mistralsolutions.com> +// +// Copyright (C) 2014-2018, Ambarella, Inc. +// Author: Dongge wu <dgwu(a)ambarella.com> +// +// Copyright (C) 2021 Axis Communications AB +// Author: Ricard Wanderlof <ricardw(a)axis.com> +// + +#include <dt-bindings/sound/tlv320adc3xxx.h> +#include <linux/clk.h> +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/io.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/gpio/driver.h> +#include <linux/pm.h> +#include <linux/i2c.h> +#include <linux/platform_device.h> +#include <linux/cdev.h> +#include <linux/of_gpio.h> +#include <linux/slab.h> +#include <sound/core.h> +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/soc-dapm.h> +#include <sound/tlv.h> +#include <sound/initval.h> + +/* + * General definitions defining exported functionality. + */ + +#define ADC3XXX_MICBIAS_PINS 2 + +/* Number of GPIO pins exposed via the gpiolib interface */ +#define ADC3XXX_GPIOS_MAX 2 + +#define ADC3XXX_RATES SNDRV_PCM_RATE_8000_96000 +#define ADC3XXX_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | \ + SNDRV_PCM_FMTBIT_S20_3LE | \ + SNDRV_PCM_FMTBIT_S24_3LE | \ + SNDRV_PCM_FMTBIT_S32_LE) + +/* + * PLL modes, to be used for clk_id for set_sysclk callback. + * + * The default behavior (AUTO) is to take the first matching entry in the clock + * table, which is intended to be the PLL based one if there is more than one. + * + * Setting the clock source using simple-card (clocks or + * system-clock-frequency property) sets clk_id = 0 = ADC3XXX_PLL_AUTO. + */ +#define ADC3XXX_PLL_AUTO 0 /* Use first available mode */ +#define ADC3XXX_PLL_ENABLE 1 /* Use PLL for clock generation */ +#define ADC3XXX_PLL_BYPASS 2 /* Don't use PLL for clock generation */ + +/* Register definitions. */ + +#define ADC3XXX_PAGE_SIZE 128 +#define ADC3XXX_REG(page, reg) ((page * ADC3XXX_PAGE_SIZE) + reg) + +/* + * Page 0 registers. + */ + +#define ADC3XXX_PAGE_SELECT ADC3XXX_REG(0, 0) +#define ADC3XXX_RESET ADC3XXX_REG(0, 1) + +/* 2-3 Reserved */ + +#define ADC3XXX_CLKGEN_MUX ADC3XXX_REG(0, 4) +#define ADC3XXX_PLL_PROG_PR ADC3XXX_REG(0, 5) +#define ADC3XXX_PLL_PROG_J ADC3XXX_REG(0, 6) +#define ADC3XXX_PLL_PROG_D_MSB ADC3XXX_REG(0, 7) +#define ADC3XXX_PLL_PROG_D_LSB ADC3XXX_REG(0, 8) + +/* 9-17 Reserved */ + +#define ADC3XXX_ADC_NADC ADC3XXX_REG(0, 18) +#define ADC3XXX_ADC_MADC ADC3XXX_REG(0, 19) +#define ADC3XXX_ADC_AOSR ADC3XXX_REG(0, 20) +#define ADC3XXX_ADC_IADC ADC3XXX_REG(0, 21) + +/* 23-24 Reserved */ + +#define ADC3XXX_CLKOUT_MUX ADC3XXX_REG(0, 25) +#define ADC3XXX_CLKOUT_M_DIV ADC3XXX_REG(0, 26) +#define ADC3XXX_INTERFACE_CTRL_1 ADC3XXX_REG(0, 27) +#define ADC3XXX_CH_OFFSET_1 ADC3XXX_REG(0, 28) +#define ADC3XXX_INTERFACE_CTRL_2 ADC3XXX_REG(0, 29) +#define ADC3XXX_BCLK_N_DIV ADC3XXX_REG(0, 30) +#define ADC3XXX_INTERFACE_CTRL_3 ADC3XXX_REG(0, 31) +#define ADC3XXX_INTERFACE_CTRL_4 ADC3XXX_REG(0, 32) +#define ADC3XXX_INTERFACE_CTRL_5 ADC3XXX_REG(0, 33) +#define ADC3XXX_I2S_SYNC ADC3XXX_REG(0, 34) +/* 35 Reserved */ +#define ADC3XXX_ADC_FLAG ADC3XXX_REG(0, 36) +#define ADC3XXX_CH_OFFSET_2 ADC3XXX_REG(0, 37) +#define ADC3XXX_I2S_TDM_CTRL ADC3XXX_REG(0, 38) +/* 39-41 Reserved */ +#define ADC3XXX_INTR_FLAG_1 ADC3XXX_REG(0, 42) +#define ADC3XXX_INTR_FLAG_2 ADC3XXX_REG(0, 43) +/* 44 Reserved */ +#define ADC3XXX_INTR_FLAG_ADC1 ADC3XXX_REG(0, 45) +/* 46 Reserved */ +#define ADC3XXX_INTR_FLAG_ADC2 ADC3XXX_REG(0, 47) +#define ADC3XXX_INT1_CTRL ADC3XXX_REG(0, 48) +#define ADC3XXX_INT2_CTRL ADC3XXX_REG(0, 49) +/* 50 Reserved */ +#define ADC3XXX_GPIO2_CTRL ADC3XXX_REG(0, 51) +#define ADC3XXX_GPIO1_CTRL ADC3XXX_REG(0, 52) +#define ADC3XXX_DOUT_CTRL ADC3XXX_REG(0, 53) +/* 54-56 Reserved */ +#define ADC3XXX_SYNC_CTRL_1 ADC3XXX_REG(0, 57) +#define ADC3XXX_SYNC_CTRL_2 ADC3XXX_REG(0, 58) +#define ADC3XXX_CIC_GAIN_CTRL ADC3XXX_REG(0, 59) +/* 60 Reserved */ +#define ADC3XXX_PRB_SELECT ADC3XXX_REG(0, 61) +#define ADC3XXX_INST_MODE_CTRL ADC3XXX_REG(0, 62) +/* 63-79 Reserved */ +#define ADC3XXX_MIC_POLARITY_CTRL ADC3XXX_REG(0, 80) +#define ADC3XXX_ADC_DIGITAL ADC3XXX_REG(0, 81) +#define ADC3XXX_ADC_FGA ADC3XXX_REG(0, 82) +#define ADC3XXX_LADC_VOL ADC3XXX_REG(0, 83) +#define ADC3XXX_RADC_VOL ADC3XXX_REG(0, 84) +#define ADC3XXX_ADC_PHASE_COMP ADC3XXX_REG(0, 85) +#define ADC3XXX_LEFT_CHN_AGC_1 ADC3XXX_REG(0, 86) +#define ADC3XXX_LEFT_CHN_AGC_2 ADC3XXX_REG(0, 87) +#define ADC3XXX_LEFT_CHN_AGC_3 ADC3XXX_REG(0, 88) +#define ADC3XXX_LEFT_CHN_AGC_4 ADC3XXX_REG(0, 89) +#define ADC3XXX_LEFT_CHN_AGC_5 ADC3XXX_REG(0, 90) +#define ADC3XXX_LEFT_CHN_AGC_6 ADC3XXX_REG(0, 91) +#define ADC3XXX_LEFT_CHN_AGC_7 ADC3XXX_REG(0, 92) +#define ADC3XXX_LEFT_AGC_GAIN ADC3XXX_REG(0, 93) +#define ADC3XXX_RIGHT_CHN_AGC_1 ADC3XXX_REG(0, 94) +#define ADC3XXX_RIGHT_CHN_AGC_2 ADC3XXX_REG(0, 95) +#define ADC3XXX_RIGHT_CHN_AGC_3 ADC3XXX_REG(0, 96) +#define ADC3XXX_RIGHT_CHN_AGC_4 ADC3XXX_REG(0, 97) +#define ADC3XXX_RIGHT_CHN_AGC_5 ADC3XXX_REG(0, 98) +#define ADC3XXX_RIGHT_CHN_AGC_6 ADC3XXX_REG(0, 99) +#define ADC3XXX_RIGHT_CHN_AGC_7 ADC3XXX_REG(0, 100) +#define ADC3XXX_RIGHT_AGC_GAIN ADC3XXX_REG(0, 101) +/* 102-127 Reserved */ + +/* + * Page 1 registers. + */ + +/* 1-25 Reserved */ +#define ADC3XXX_DITHER_CTRL ADC3XXX_REG(1, 26) +/* 27-50 Reserved */ +#define ADC3XXX_MICBIAS_CTRL ADC3XXX_REG(1, 51) +#define ADC3XXX_LEFT_PGA_SEL_1 ADC3XXX_REG(1, 52) +/* 53 Reserved */ +#define ADC3XXX_LEFT_PGA_SEL_2 ADC3XXX_REG(1, 54) +#define ADC3XXX_RIGHT_PGA_SEL_1 ADC3XXX_REG(1, 55) +#define ADC3XXX_RIGHT_PGA_SEL_2 ADC3XXX_REG(1, 57) +#define ADC3XXX_LEFT_APGA_CTRL ADC3XXX_REG(1, 59) +#define ADC3XXX_RIGHT_APGA_CTRL ADC3XXX_REG(1, 60) +#define ADC3XXX_LOW_CURRENT_MODES ADC3XXX_REG(1, 61) +#define ADC3XXX_ANALOG_PGA_FLAGS ADC3XXX_REG(1, 62) +/* 63-127 Reserved */ + +/* + * Register bits. + */ + +/* PLL Enable bits */ +#define ADC3XXX_ENABLE_PLL_SHIFT 7 +#define ADC3XXX_ENABLE_PLL (1 << ADC3XXX_ENABLE_PLL_SHIFT) +#define ADC3XXX_ENABLE_NADC_SHIFT 7 +#define ADC3XXX_ENABLE_NADC (1 << ADC3XXX_ENABLE_NADC_SHIFT) +#define ADC3XXX_ENABLE_MADC_SHIFT 7 +#define ADC3XXX_ENABLE_MADC (1 << ADC3XXX_ENABLE_MADC_SHIFT) +#define ADC3XXX_ENABLE_BCLK_SHIFT 7 +#define ADC3XXX_ENABLE_BCLK (1 << ADC3XXX_ENABLE_BCLK_SHIFT) + +/* Power bits */ +#define ADC3XXX_LADC_PWR_ON 0x80 +#define ADC3XXX_RADC_PWR_ON 0x40 + +#define ADC3XXX_SOFT_RESET 0x01 +#define ADC3XXX_BCLK_MASTER 0x08 +#define ADC3XXX_WCLK_MASTER 0x04 + +/* Interface register masks */ +#define ADC3XXX_FORMAT_MASK 0xc0 +#define ADC3XXX_FORMAT_SHIFT 6 +#define ADC3XXX_WLENGTH_MASK 0x30 +#define ADC3XXX_WLENGTH_SHIFT 4 +#define ADC3XXX_CLKDIR_MASK 0x0c +#define ADC3XXX_CLKDIR_SHIFT 2 + +/* Interface register bit patterns */ +#define ADC3XXX_FORMAT_I2S (0 << ADC3XXX_FORMAT_SHIFT) +#define ADC3XXX_FORMAT_DSP (1 << ADC3XXX_FORMAT_SHIFT) +#define ADC3XXX_FORMAT_RJF (2 << ADC3XXX_FORMAT_SHIFT) +#define ADC3XXX_FORMAT_LJF (3 << ADC3XXX_FORMAT_SHIFT) + +#define ADC3XXX_IFACE_16BITS (0 << ADC3XXX_WLENGTH_SHIFT) +#define ADC3XXX_IFACE_20BITS (1 << ADC3XXX_WLENGTH_SHIFT) +#define ADC3XXX_IFACE_24BITS (2 << ADC3XXX_WLENGTH_SHIFT) +#define ADC3XXX_IFACE_32BITS (3 << ADC3XXX_WLENGTH_SHIFT) + +/* PLL P/R bit offsets */ +#define ADC3XXX_PLLP_SHIFT 4 +#define ADC3XXX_PLLR_SHIFT 0 +#define ADC3XXX_PLL_PR_MASK 0x7f +#define ADC3XXX_PLLJ_MASK 0x3f +#define ADC3XXX_PLLD_MSB_MASK 0x3f +#define ADC3XXX_PLLD_LSB_MASK 0xff +#define ADC3XXX_NADC_MASK 0x7f +#define ADC3XXX_MADC_MASK 0x7f +#define ADC3XXX_AOSR_MASK 0xff +#define ADC3XXX_IADC_MASK 0xff +#define ADC3XXX_BDIV_MASK 0x7f + +/* PLL_CLKIN bits */ +#define ADC3XXX_PLL_CLKIN_SHIFT 2 +#define ADC3XXX_PLL_CLKIN_MCLK 0x0 +#define ADC3XXX_PLL_CLKIN_BCLK 0x1 +#define ADC3XXX_PLL_CLKIN_ZERO 0x3 + +/* CODEC_CLKIN bits */ +#define ADC3XXX_CODEC_CLKIN_SHIFT 0 +#define ADC3XXX_CODEC_CLKIN_MCLK 0x0 +#define ADC3XXX_CODEC_CLKIN_BCLK 0x1 +#define ADC3XXX_CODEC_CLKIN_PLL_CLK 0x3 + +#define ADC3XXX_USE_PLL ((ADC3XXX_PLL_CLKIN_MCLK << ADC3XXX_PLL_CLKIN_SHIFT) | \ + (ADC3XXX_CODEC_CLKIN_PLL_CLK << ADC3XXX_CODEC_CLKIN_SHIFT)) +#define ADC3XXX_NO_PLL ((ADC3XXX_PLL_CLKIN_ZERO << ADC3XXX_PLL_CLKIN_SHIFT) | \ + (ADC3XXX_CODEC_CLKIN_MCLK << ADC3XXX_CODEC_CLKIN_SHIFT)) + +/* Analog PGA control bits */ +#define ADC3XXX_LPGA_MUTE 0x80 +#define ADC3XXX_RPGA_MUTE 0x80 + +#define ADC3XXX_LPGA_GAIN_MASK 0x7f +#define ADC3XXX_RPGA_GAIN_MASK 0x7f + +/* ADC current modes */ +#define ADC3XXX_ADC_LOW_CURR_MODE 0x01 + +/* Left ADC Input selection bits */ +#define ADC3XXX_LCH_SEL1_SHIFT 0 +#define ADC3XXX_LCH_SEL2_SHIFT 2 +#define ADC3XXX_LCH_SEL3_SHIFT 4 +#define ADC3XXX_LCH_SEL4_SHIFT 6 + +#define ADC3XXX_LCH_SEL1X_SHIFT 0 +#define ADC3XXX_LCH_SEL2X_SHIFT 2 +#define ADC3XXX_LCH_SEL3X_SHIFT 4 +#define ADC3XXX_LCH_COMMON_MODE 0x40 +#define ADC3XXX_BYPASS_LPGA 0x80 + +/* Right ADC Input selection bits */ +#define ADC3XXX_RCH_SEL1_SHIFT 0 +#define ADC3XXX_RCH_SEL2_SHIFT 2 +#define ADC3XXX_RCH_SEL3_SHIFT 4 +#define ADC3XXX_RCH_SEL4_SHIFT 6 + +#define ADC3XXX_RCH_SEL1X_SHIFT 0 +#define ADC3XXX_RCH_SEL2X_SHIFT 2 +#define ADC3XXX_RCH_SEL3X_SHIFT 4 +#define ADC3XXX_RCH_COMMON_MODE 0x40 +#define ADC3XXX_BYPASS_RPGA 0x80 + +/* MICBIAS control bits */ +#define ADC3XXX_MICBIAS_MASK 0x2 +#define ADC3XXX_MICBIAS1_SHIFT 5 +#define ADC3XXX_MICBIAS2_SHIFT 3 + +#define ADC3XXX_ADC_MAX_VOLUME 64 +#define ADC3XXX_ADC_POS_VOL 24 + +/* GPIO control bits (GPIO1_CTRL and GPIO2_CTRL) */ +#define ADC3XXX_GPIO_CTRL_CFG_MASK 0x3c +#define ADC3XXX_GPIO_CTRL_CFG_SHIFT 2 +#define ADC3XXX_GPIO_CTRL_OUTPUT_CTRL_MASK 0x01 +#define ADC3XXX_GPIO_CTRL_OUTPUT_CTRL_SHIFT 0 +#define ADC3XXX_GPIO_CTRL_INPUT_VALUE_MASK 0x02 +#define ADC3XXX_GPIO_CTRL_INPUT_VALUE_SHIFT 1 + +enum adc3xxx_type { + ADC3001 = 0, + ADC3101 +}; + +struct adc3xxx { + struct device *dev; + enum adc3xxx_type type; + struct clk *mclk; + struct regmap *regmap; + struct gpio_desc *rst_pin; + unsigned int pll_mode; + unsigned int sysclk; + unsigned int gpio_cfg[ADC3XXX_GPIOS_MAX]; /* value+1 (0 => not set) */ + unsigned int micbias_vg[ADC3XXX_MICBIAS_PINS]; + int master; + u8 page_no; + int use_pll; + struct gpio_chip gpio_chip; +}; + +static const unsigned int adc3xxx_gpio_ctrl_reg[ADC3XXX_GPIOS_MAX] = { + ADC3XXX_GPIO1_CTRL, + ADC3XXX_GPIO2_CTRL +}; + +static const unsigned int adc3xxx_micbias_shift[ADC3XXX_MICBIAS_PINS] = { + ADC3XXX_MICBIAS1_SHIFT, + ADC3XXX_MICBIAS2_SHIFT +}; + +static const struct reg_default adc3xxx_defaults[] = { + /* Page 0 */ + { 0, 0x00 }, { 1, 0x00 }, { 2, 0x00 }, { 3, 0x00 }, + { 4, 0x00 }, { 5, 0x11 }, { 6, 0x04 }, { 7, 0x00 }, + { 8, 0x00 }, { 9, 0x00 }, { 10, 0x00 }, { 11, 0x00 }, + { 12, 0x00 }, { 13, 0x00 }, { 14, 0x00 }, { 15, 0x00 }, + { 16, 0x00 }, { 17, 0x00 }, { 18, 0x01 }, { 19, 0x01 }, + { 20, 0x80 }, { 21, 0x80 }, { 22, 0x04 }, { 23, 0x00 }, + { 24, 0x00 }, { 25, 0x00 }, { 26, 0x01 }, { 27, 0x00 }, + { 28, 0x00 }, { 29, 0x02 }, { 30, 0x01 }, { 31, 0x00 }, + { 32, 0x00 }, { 33, 0x10 }, { 34, 0x00 }, { 35, 0x00 }, + { 36, 0x00 }, { 37, 0x00 }, { 38, 0x02 }, { 39, 0x00 }, + { 40, 0x00 }, { 41, 0x00 }, { 42, 0x00 }, { 43, 0x00 }, + { 44, 0x00 }, { 45, 0x00 }, { 46, 0x00 }, { 47, 0x00 }, + { 48, 0x00 }, { 49, 0x00 }, { 50, 0x00 }, { 51, 0x00 }, + { 52, 0x00 }, { 53, 0x12 }, { 54, 0x00 }, { 55, 0x00 }, + { 56, 0x00 }, { 57, 0x00 }, { 58, 0x00 }, { 59, 0x44 }, + { 60, 0x00 }, { 61, 0x01 }, { 62, 0x00 }, { 63, 0x00 }, + { 64, 0x00 }, { 65, 0x00 }, { 66, 0x00 }, { 67, 0x00 }, + { 68, 0x00 }, { 69, 0x00 }, { 70, 0x00 }, { 71, 0x00 }, + { 72, 0x00 }, { 73, 0x00 }, { 74, 0x00 }, { 75, 0x00 }, + { 76, 0x00 }, { 77, 0x00 }, { 78, 0x00 }, { 79, 0x00 }, + { 80, 0x00 }, { 81, 0x00 }, { 82, 0x88 }, { 83, 0x00 }, + { 84, 0x00 }, { 85, 0x00 }, { 86, 0x00 }, { 87, 0x00 }, + { 88, 0x7f }, { 89, 0x00 }, { 90, 0x00 }, { 91, 0x00 }, + { 92, 0x00 }, { 93, 0x00 }, { 94, 0x00 }, { 95, 0x00 }, + { 96, 0x7f }, { 97, 0x00 }, { 98, 0x00 }, { 99, 0x00 }, + { 100, 0x00 }, { 101, 0x00 }, { 102, 0x00 }, { 103, 0x00 }, + { 104, 0x00 }, { 105, 0x00 }, { 106, 0x00 }, { 107, 0x00 }, + { 108, 0x00 }, { 109, 0x00 }, { 110, 0x00 }, { 111, 0x00 }, + { 112, 0x00 }, { 113, 0x00 }, { 114, 0x00 }, { 115, 0x00 }, + { 116, 0x00 }, { 117, 0x00 }, { 118, 0x00 }, { 119, 0x00 }, + { 120, 0x00 }, { 121, 0x00 }, { 122, 0x00 }, { 123, 0x00 }, + { 124, 0x00 }, { 125, 0x00 }, { 126, 0x00 }, { 127, 0x00 }, + + /* Page 1 */ + { 128, 0x00 }, { 129, 0x00 }, { 130, 0x00 }, { 131, 0x00 }, + { 132, 0x00 }, { 133, 0x00 }, { 134, 0x00 }, { 135, 0x00 }, + { 136, 0x00 }, { 137, 0x00 }, { 138, 0x00 }, { 139, 0x00 }, + { 140, 0x00 }, { 141, 0x00 }, { 142, 0x00 }, { 143, 0x00 }, + { 144, 0x00 }, { 145, 0x00 }, { 146, 0x00 }, { 147, 0x00 }, + { 148, 0x00 }, { 149, 0x00 }, { 150, 0x00 }, { 151, 0x00 }, + { 152, 0x00 }, { 153, 0x00 }, { 154, 0x00 }, { 155, 0x00 }, + { 156, 0x00 }, { 157, 0x00 }, { 158, 0x00 }, { 159, 0x00 }, + { 160, 0x00 }, { 161, 0x00 }, { 162, 0x00 }, { 163, 0x00 }, + { 164, 0x00 }, { 165, 0x00 }, { 166, 0x00 }, { 167, 0x00 }, + { 168, 0x00 }, { 169, 0x00 }, { 170, 0x00 }, { 171, 0x00 }, + { 172, 0x00 }, { 173, 0x00 }, { 174, 0x00 }, { 175, 0x00 }, + { 176, 0x00 }, { 177, 0x00 }, { 178, 0x00 }, { 179, 0x00 }, + { 180, 0xff }, { 181, 0x00 }, { 182, 0x3f }, { 183, 0xff }, + { 184, 0x00 }, { 185, 0x3f }, { 186, 0x00 }, { 187, 0x80 }, + { 188, 0x80 }, { 189, 0x00 }, { 190, 0x00 }, { 191, 0x00 }, +}; + +static bool adc3xxx_volatile_reg(struct device *dev, unsigned int reg) +{ + switch (reg) { + case ADC3XXX_RESET: + return true; + default: + return false; + } +} + +static const struct regmap_range_cfg adc3xxx_ranges[] = { + { + .range_min = 0, + .range_max = 2 * ADC3XXX_PAGE_SIZE, + .selector_reg = ADC3XXX_PAGE_SELECT, + .selector_mask = 0xff, + .selector_shift = 0, + .window_start = 0, + .window_len = ADC3XXX_PAGE_SIZE, + } +}; + +static const struct regmap_config adc3xxx_regmap = { + .reg_bits = 8, + .val_bits = 8, + + .reg_defaults = adc3xxx_defaults, + .num_reg_defaults = ARRAY_SIZE(adc3xxx_defaults), + + .volatile_reg = adc3xxx_volatile_reg, + + .cache_type = REGCACHE_RBTREE, + + .ranges = adc3xxx_ranges, + .num_ranges = ARRAY_SIZE(adc3xxx_ranges), + .max_register = 2 * ADC3XXX_PAGE_SIZE, +}; + +struct adc3xxx_rate_divs { + u32 mclk; + u32 rate; + u8 pll_p; + u8 pll_r; + u8 pll_j; + u16 pll_d; + u8 nadc; + u8 madc; + u8 aosr; +}; + +/* + * PLL and Clock settings. + * If p member is 0, PLL is not used. + * The order of the entries in this table have the PLL entries before + * the non-PLL entries, so that the PLL modes are preferred unless + * the PLL mode setting says otherwise. + */ +static const struct adc3xxx_rate_divs adc3xxx_divs[] = { + /* mclk, rate, p, r, j, d, nadc, madc, aosr */ + /* 8k rate */ + { 12000000, 8000, 1, 1, 7, 1680, 42, 2, 128 }, + { 12288000, 8000, 1, 1, 7, 0000, 42, 2, 128 }, + /* 11.025k rate */ + { 12000000, 11025, 1, 1, 6, 8208, 29, 2, 128 }, + /* 16k rate */ + { 12000000, 16000, 1, 1, 7, 1680, 21, 2, 128 }, + { 12288000, 16000, 1, 1, 7, 0000, 21, 2, 128 }, + /* 22.05k rate */ + { 12000000, 22050, 1, 1, 7, 560, 15, 2, 128 }, + /* 32k rate */ + { 12000000, 32000, 1, 1, 8, 1920, 12, 2, 128 }, + { 12288000, 32000, 1, 1, 8, 0000, 12, 2, 128 }, + /* 44.1k rate */ + { 12000000, 44100, 1, 1, 7, 5264, 8, 2, 128 }, + /* 48k rate */ + { 12000000, 48000, 1, 1, 7, 1680, 7, 2, 128 }, + { 12288000, 48000, 1, 1, 7, 0000, 7, 2, 128 }, + { 24576000, 48000, 1, 1, 3, 5000, 7, 2, 128 }, /* With PLL */ + { 24576000, 48000, 0, 0, 0, 0000, 2, 2, 128 }, /* Without PLL */ + /* 88.2k rate */ + { 12000000, 88200, 1, 1, 7, 5264, 4, 4, 64 }, + /* 96k rate */ + { 12000000, 96000, 1, 1, 8, 1920, 4, 4, 64 }, +}; + +static int adc3xxx_get_divs(struct device *dev, int mclk, int rate, int pll_mode) +{ + int i; + + dev_dbg(dev, "mclk = %d, rate = %d, clock mode %u\n", + mclk, rate, pll_mode); + for (i = 0; i < ARRAY_SIZE(adc3xxx_divs); i++) { + const struct adc3xxx_rate_divs *mode = &adc3xxx_divs[i]; + + /* Skip this entry if it doesn't fulfill the intended clock + * mode requirement. We consider anything besides the two + * modes below to be the same as ADC3XXX_PLL_AUTO. + */ + if ((pll_mode == ADC3XXX_PLL_BYPASS && mode->pll_p) || + (pll_mode == ADC3XXX_PLL_ENABLE && !mode->pll_p)) + continue; + + if (mode->rate == rate && mode->mclk == mclk) + return i; + } + + dev_info(dev, "Master clock rate %d and sample rate %d is not supported\n", + mclk, rate); + return -EINVAL; +} + +static int adc3xxx_pll_delay(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + /* 10msec delay needed after PLL power-up to allow + * PLL and dividers to stabilize (datasheet p13). + */ + usleep_range(10000, 20000); + + return 0; +} + +static const char * const adc_softstepping_text[] = { "1 step", "2 step", "off" }; +static SOC_ENUM_SINGLE_DECL(adc_softstepping_enum, ADC3XXX_ADC_DIGITAL, 0, + adc_softstepping_text); + +static const char * const multiplier_text[] = { "1", "2", "4", "8", "16", "32", "64", "128" }; +static SOC_ENUM_SINGLE_DECL(left_agc_attack_mult_enum, + ADC3XXX_LEFT_CHN_AGC_4, 0, multiplier_text); +static SOC_ENUM_SINGLE_DECL(right_agc_attack_mult_enum, + ADC3XXX_RIGHT_CHN_AGC_4, 0, multiplier_text); +static SOC_ENUM_SINGLE_DECL(left_agc_decay_mult_enum, + ADC3XXX_LEFT_CHN_AGC_5, 0, multiplier_text); +static SOC_ENUM_SINGLE_DECL(right_agc_decay_mult_enum, + ADC3XXX_RIGHT_CHN_AGC_5, 0, multiplier_text); + +static const char * const dither_dc_offset_text[] = { + "0mV", "15mV", "30mV", "45mV", "60mV", "75mV", "90mV", "105mV", + "-15mV", "-30mV", "-45mV", "-60mV", "-75mV", "-90mV", "-105mV" +}; +static const unsigned int dither_dc_offset_values[] = { + 0, 1, 2, 3, 4, 5, 6, 7, 9, 10, 11, 12, 13, 14, 15 +}; +static SOC_VALUE_ENUM_DOUBLE_DECL(dither_dc_offset_enum, + ADC3XXX_DITHER_CTRL, + 4, 0, 0xf, dither_dc_offset_text, + dither_dc_offset_values); + +static const DECLARE_TLV_DB_SCALE(pga_tlv, 0, 50, 0); +static const DECLARE_TLV_DB_SCALE(adc_tlv, -1200, 50, 0); +static const DECLARE_TLV_DB_SCALE(adc_fine_tlv, -40, 10, 0); +/* AGC target: 8 values: -5.5, -8, -10, -12, -14, -17, -20, -24 dB */ +/* It would be nice to declare these in the order above, but empirically + * TLV_DB_SCALE_ITEM doesn't take lightly to the increment (second) parameter + * being negative, despite there being examples to the contrary in other + * drivers. So declare these in the order from lowest to highest, and + * set the invert flag in the SOC_DOUBLE_R_TLV declaration instead. + */ +static const DECLARE_TLV_DB_RANGE(agc_target_tlv, + 0, 0, TLV_DB_SCALE_ITEM(-2400, 0, 0), + 1, 3, TLV_DB_SCALE_ITEM(-2000, 300, 0), + 4, 6, TLV_DB_SCALE_ITEM(-1200, 200, 0), + 7, 7, TLV_DB_SCALE_ITEM(-550, 0, 0)); +/* Since the 'disabled' value (mute) is at the highest value in the dB + * range (i.e. just before -32 dB) rather than the lowest, we need to resort + * to using a TLV_DB_RANGE in order to get the mute value in the right place. + */ +static const DECLARE_TLV_DB_RANGE(agc_thresh_tlv, + 0, 30, TLV_DB_SCALE_ITEM(-9000, 200, 0), + 31, 31, TLV_DB_SCALE_ITEM(0, 0, 1)); /* disabled = mute */ +/* AGC hysteresis: 4 values: 1, 2, 4 dB, disabled (= mute) */ +static const DECLARE_TLV_DB_RANGE(agc_hysteresis_tlv, + 0, 1, TLV_DB_SCALE_ITEM(100, 100, 0), + 2, 2, TLV_DB_SCALE_ITEM(400, 0, 0), + 3, 3, TLV_DB_SCALE_ITEM(0, 0, 1)); /* disabled = mute */ +static const DECLARE_TLV_DB_SCALE(agc_max_tlv, 0, 50, 0); +/* Input attenuation: -6 dB or 0 dB */ +static const DECLARE_TLV_DB_SCALE(input_attenuation_tlv, -600, 600, 0); + +static const struct snd_kcontrol_new adc3xxx_snd_controls[] = { + SOC_DOUBLE_R_TLV("PGA Capture Volume", ADC3XXX_LEFT_APGA_CTRL, + ADC3XXX_RIGHT_APGA_CTRL, 0, 80, 0, pga_tlv), + SOC_DOUBLE("PGA Capture Switch", ADC3XXX_ADC_FGA, 7, 3, 1, 1), + SOC_DOUBLE_R("AGC Capture Switch", ADC3XXX_LEFT_CHN_AGC_1, + ADC3XXX_RIGHT_CHN_AGC_1, 7, 1, 0), + SOC_DOUBLE_R_TLV("AGC Target Level Capture Volume", ADC3XXX_LEFT_CHN_AGC_1, + ADC3XXX_RIGHT_CHN_AGC_2, 4, 0x07, 1, agc_target_tlv), + SOC_DOUBLE_R_TLV("AGC Noise Threshold Capture Volume", ADC3XXX_LEFT_CHN_AGC_2, + ADC3XXX_RIGHT_CHN_AGC_2, 1, 0x1f, 1, agc_thresh_tlv), + SOC_DOUBLE_R_TLV("AGC Hysteresis Capture Volume", ADC3XXX_LEFT_CHN_AGC_2, + ADC3XXX_RIGHT_CHN_AGC_2, 6, 3, 0, agc_hysteresis_tlv), + SOC_DOUBLE_R("AGC Clip Stepping Capture Switch", ADC3XXX_LEFT_CHN_AGC_2, + ADC3XXX_RIGHT_CHN_AGC_2, 0, 1, 0), + /* + * Oddly enough, the data sheet says the default value + * for the left/right AGC maximum gain register field + * (ADC3XXX_LEFT/RIGHT_CHN_AGC_3 bits 0..6) is 0x7f = 127 + * (verified empirically) even though this value (indeed, above + * 0x50) is specified as 'Reserved. Do not use.' in the accompanying + * table in the data sheet. + */ + SOC_DOUBLE_R_TLV("AGC Maximum Capture Volume", ADC3XXX_LEFT_CHN_AGC_3, + ADC3XXX_RIGHT_CHN_AGC_3, 0, 0x50, 0, agc_max_tlv), + SOC_DOUBLE_R("AGC Attack Time", ADC3XXX_LEFT_CHN_AGC_4, + ADC3XXX_RIGHT_CHN_AGC_4, 3, 0x1f, 0), + /* Would like to have the multipliers as LR pairs, but there is + * no SOC_ENUM_foo which accepts two values in separate registers. + */ + SOC_ENUM("AGC Left Attack Time Multiplier", left_agc_attack_mult_enum), + SOC_ENUM("AGC Right Attack Time Multiplier", right_agc_attack_mult_enum), + SOC_DOUBLE_R("AGC Decay Time", ADC3XXX_LEFT_CHN_AGC_5, + ADC3XXX_RIGHT_CHN_AGC_5, 3, 0x1f, 0), + SOC_ENUM("AGC Left Decay Time Multiplier", left_agc_decay_mult_enum), + SOC_ENUM("AGC Right Decay Time Multiplier", right_agc_decay_mult_enum), + SOC_DOUBLE_R("AGC Noise Debounce", ADC3XXX_LEFT_CHN_AGC_6, + ADC3XXX_RIGHT_CHN_AGC_6, 0, 0x1f, 0), + SOC_DOUBLE_R("AGC Signal Debounce", ADC3XXX_LEFT_CHN_AGC_7, + ADC3XXX_RIGHT_CHN_AGC_7, 0, 0x0f, 0), + /* Read only register */ + SOC_DOUBLE_R_S_TLV("AGC Applied Capture Volume", ADC3XXX_LEFT_AGC_GAIN, + ADC3XXX_RIGHT_AGC_GAIN, 0, -24, 40, 6, 0, adc_tlv), + /* ADC soft stepping */ + SOC_ENUM("ADC Soft Stepping", adc_softstepping_enum), + /* Left/Right Input attenuation */ + SOC_SINGLE_TLV("Left Input IN_1L Capture Volume", + ADC3XXX_LEFT_PGA_SEL_1, 0, 1, 1, input_attenuation_tlv), + SOC_SINGLE_TLV("Left Input IN_2L Capture Volume", + ADC3XXX_LEFT_PGA_SEL_1, 2, 1, 1, input_attenuation_tlv), + SOC_SINGLE_TLV("Left Input IN_3L Capture Volume", + ADC3XXX_LEFT_PGA_SEL_1, 4, 1, 1, input_attenuation_tlv), + SOC_SINGLE_TLV("Left Input IN_1R Capture Volume", + ADC3XXX_LEFT_PGA_SEL_2, 0, 1, 1, input_attenuation_tlv), + SOC_SINGLE_TLV("Left Input DIF_2L_3L Capture Volume", + ADC3XXX_LEFT_PGA_SEL_1, 6, 1, 1, input_attenuation_tlv), + SOC_SINGLE_TLV("Left Input DIF_1L_1R Capture Volume", + ADC3XXX_LEFT_PGA_SEL_2, 4, 1, 1, input_attenuation_tlv), + SOC_SINGLE_TLV("Left Input DIF_2R_3R Capture Volume", + ADC3XXX_LEFT_PGA_SEL_2, 2, 1, 1, input_attenuation_tlv), + SOC_SINGLE_TLV("Right Input IN_1R Capture Volume", + ADC3XXX_RIGHT_PGA_SEL_1, 0, 1, 1, input_attenuation_tlv), + SOC_SINGLE_TLV("Right Input IN_2R Capture Volume", + ADC3XXX_RIGHT_PGA_SEL_1, 2, 1, 1, input_attenuation_tlv), + SOC_SINGLE_TLV("Right Input IN_3R Capture Volume", + ADC3XXX_RIGHT_PGA_SEL_1, 4, 1, 1, input_attenuation_tlv), + SOC_SINGLE_TLV("Right Input IN_1L Capture Volume", + ADC3XXX_RIGHT_PGA_SEL_2, 0, 1, 1, input_attenuation_tlv), + SOC_SINGLE_TLV("Right Input DIF_2R_3R Capture Volume", + ADC3XXX_RIGHT_PGA_SEL_1, 6, 1, 1, input_attenuation_tlv), + SOC_SINGLE_TLV("Right Input DIF_1L_1R Capture Volume", + ADC3XXX_RIGHT_PGA_SEL_2, 4, 1, 1, input_attenuation_tlv), + SOC_SINGLE_TLV("Right Input DIF_2L_3L Capture Volume", + ADC3XXX_RIGHT_PGA_SEL_2, 2, 1, 1, input_attenuation_tlv), + SOC_DOUBLE_R_S_TLV("ADC Volume Control Capture Volume", ADC3XXX_LADC_VOL, + ADC3XXX_RADC_VOL, 0, -24, 40, 6, 0, adc_tlv), + /* Empirically, the following doesn't work the way it's supposed + * to. Values 0, -0.1, -0.2 and -0.3 dB result in the same level, and + * -0.4 dB drops about 0.12 dB on a specific chip. + */ + SOC_DOUBLE_TLV("ADC Fine Volume Control Capture Volume", ADC3XXX_ADC_FGA, + 4, 0, 4, 1, adc_fine_tlv), + SOC_SINGLE("Left ADC Unselected CM Bias Capture Switch", + ADC3XXX_LEFT_PGA_SEL_2, 6, 1, 0), + SOC_SINGLE("Right ADC Unselected CM Bias Capture Switch", + ADC3XXX_RIGHT_PGA_SEL_2, 6, 1, 0), + SOC_ENUM("Dither Control DC Offset", dither_dc_offset_enum), +}; + +/* Left input selection, Single Ended inputs and Differential inputs */ +static const struct snd_kcontrol_new left_input_mixer_controls[] = { + SOC_DAPM_SINGLE("IN_1L Capture Switch", + ADC3XXX_LEFT_PGA_SEL_1, 1, 0x1, 1), + SOC_DAPM_SINGLE("IN_2L Capture Switch", + ADC3XXX_LEFT_PGA_SEL_1, 3, 0x1, 1), + SOC_DAPM_SINGLE("IN_3L Capture Switch", + ADC3XXX_LEFT_PGA_SEL_1, 5, 0x1, 1), + SOC_DAPM_SINGLE("DIF_2L_3L Capture Switch", + ADC3XXX_LEFT_PGA_SEL_1, 7, 0x1, 1), + SOC_DAPM_SINGLE("DIF_1L_1R Capture Switch", + ADC3XXX_LEFT_PGA_SEL_2, 5, 0x1, 1), + SOC_DAPM_SINGLE("DIF_2R_3R Capture Switch", + ADC3XXX_LEFT_PGA_SEL_2, 3, 0x1, 1), + SOC_DAPM_SINGLE("IN_1R Capture Switch", + ADC3XXX_LEFT_PGA_SEL_2, 1, 0x1, 1), +}; + +/* Right input selection, Single Ended inputs and Differential inputs */ +static const struct snd_kcontrol_new right_input_mixer_controls[] = { + SOC_DAPM_SINGLE("IN_1R Capture Switch", + ADC3XXX_RIGHT_PGA_SEL_1, 1, 0x1, 1), + SOC_DAPM_SINGLE("IN_2R Capture Switch", + ADC3XXX_RIGHT_PGA_SEL_1, 3, 0x1, 1), + SOC_DAPM_SINGLE("IN_3R Capture Switch", + ADC3XXX_RIGHT_PGA_SEL_1, 5, 0x1, 1), + SOC_DAPM_SINGLE("DIF_2R_3R Capture Switch", + ADC3XXX_RIGHT_PGA_SEL_1, 7, 0x1, 1), + SOC_DAPM_SINGLE("DIF_1L_1R Capture Switch", + ADC3XXX_RIGHT_PGA_SEL_2, 5, 0x1, 1), + SOC_DAPM_SINGLE("DIF_2L_3L Capture Switch", + ADC3XXX_RIGHT_PGA_SEL_2, 3, 0x1, 1), + SOC_DAPM_SINGLE("IN_1L Capture Switch", + ADC3XXX_RIGHT_PGA_SEL_2, 1, 0x1, 1), +}; + +/* Left Digital Mic input for left ADC */ +static const struct snd_kcontrol_new left_input_dmic_controls[] = { + SOC_DAPM_SINGLE("Left ADC Capture Switch", + ADC3XXX_ADC_DIGITAL, 3, 0x1, 0), +}; + +/* Right Digital Mic input for Right ADC */ +static const struct snd_kcontrol_new right_input_dmic_controls[] = { + SOC_DAPM_SINGLE("Right ADC Capture Switch", + ADC3XXX_ADC_DIGITAL, 2, 0x1, 0), +}; + +/* DAPM widgets */ +static const struct snd_soc_dapm_widget adc3xxx_dapm_widgets[] = { + + /* Left Input Selection */ + SND_SOC_DAPM_MIXER("Left Input", SND_SOC_NOPM, 0, 0, + &left_input_mixer_controls[0], + ARRAY_SIZE(left_input_mixer_controls)), + /* Right Input Selection */ + SND_SOC_DAPM_MIXER("Right Input", SND_SOC_NOPM, 0, 0, + &right_input_mixer_controls[0], + ARRAY_SIZE(right_input_mixer_controls)), + /* PGA selection */ + SND_SOC_DAPM_PGA("Left PGA", ADC3XXX_LEFT_APGA_CTRL, 7, 1, NULL, 0), + SND_SOC_DAPM_PGA("Right PGA", ADC3XXX_RIGHT_APGA_CTRL, 7, 1, NULL, 0), + + /* Digital Microphone Input Control for Left/Right ADC */ + SND_SOC_DAPM_MIXER("Left DMic Input", SND_SOC_NOPM, 0, 0, + &left_input_dmic_controls[0], + ARRAY_SIZE(left_input_dmic_controls)), + SND_SOC_DAPM_MIXER("Right DMic Input", SND_SOC_NOPM, 0, 0, + &right_input_dmic_controls[0], + ARRAY_SIZE(right_input_dmic_controls)), + + /* Left/Right ADC */ + SND_SOC_DAPM_ADC("Left ADC", "Left Capture", ADC3XXX_ADC_DIGITAL, 7, 0), + SND_SOC_DAPM_ADC("Right ADC", "Right Capture", ADC3XXX_ADC_DIGITAL, 6, 0), + + /* Inputs */ + SND_SOC_DAPM_INPUT("IN_1L"), + SND_SOC_DAPM_INPUT("IN_1R"), + SND_SOC_DAPM_INPUT("IN_2L"), + SND_SOC_DAPM_INPUT("IN_2R"), + SND_SOC_DAPM_INPUT("IN_3L"), + SND_SOC_DAPM_INPUT("IN_3R"), + SND_SOC_DAPM_INPUT("DIFL_1L_1R"), + SND_SOC_DAPM_INPUT("DIFL_2L_3L"), + SND_SOC_DAPM_INPUT("DIFL_2R_3R"), + SND_SOC_DAPM_INPUT("DIFR_1L_1R"), + SND_SOC_DAPM_INPUT("DIFR_2L_3L"), + SND_SOC_DAPM_INPUT("DIFR_2R_3R"), + SND_SOC_DAPM_INPUT("DMic_L"), + SND_SOC_DAPM_INPUT("DMic_R"), + + /* Digital audio interface output */ + SND_SOC_DAPM_AIF_OUT("AIF_OUT", "Capture", 0, SND_SOC_NOPM, 0, 0), + + /* Clocks */ + SND_SOC_DAPM_SUPPLY("PLL_CLK", ADC3XXX_PLL_PROG_PR, ADC3XXX_ENABLE_PLL_SHIFT, + 0, adc3xxx_pll_delay, SND_SOC_DAPM_POST_PMU), + + SND_SOC_DAPM_SUPPLY("ADC_CLK", ADC3XXX_ADC_NADC, ADC3XXX_ENABLE_NADC_SHIFT, + 0, NULL, 0), + SND_SOC_DAPM_SUPPLY("ADC_MOD_CLK", ADC3XXX_ADC_MADC, ADC3XXX_ENABLE_MADC_SHIFT, + 0, NULL, 0), + + /* This refers to the generated BCLK in master mode. */ + SND_SOC_DAPM_SUPPLY("BCLK", ADC3XXX_BCLK_N_DIV, ADC3XXX_ENABLE_BCLK_SHIFT, + 0, NULL, 0), +}; + +static const struct snd_soc_dapm_route adc3xxx_intercon[] = { + /* Left input selection from switches */ + { "Left Input", "IN_1L Capture Switch", "IN_1L" }, + { "Left Input", "IN_2L Capture Switch", "IN_2L" }, + { "Left Input", "IN_3L Capture Switch", "IN_3L" }, + { "Left Input", "DIF_2L_3L Capture Switch", "DIFL_2L_3L" }, + { "Left Input", "DIF_1L_1R Capture Switch", "DIFL_1L_1R" }, + { "Left Input", "DIF_2R_3R Capture Switch", "DIFL_2R_3R" }, + { "Left Input", "IN_1R Capture Switch", "IN_1R" }, + + /* Left input selection to left PGA */ + { "Left PGA", NULL, "Left Input" }, + + /* Left PGA to left ADC */ + { "Left ADC", NULL, "Left PGA" }, + + /* Right input selection from switches */ + { "Right Input", "IN_1R Capture Switch", "IN_1R" }, + { "Right Input", "IN_2R Capture Switch", "IN_2R" }, + { "Right Input", "IN_3R Capture Switch", "IN_3R" }, + { "Right Input", "DIF_2R_3R Capture Switch", "DIFR_2R_3R" }, + { "Right Input", "DIF_1L_1R Capture Switch", "DIFR_1L_1R" }, + { "Right Input", "DIF_2L_3L Capture Switch", "DIFR_2L_3L" }, + { "Right Input", "IN_1L Capture Switch", "IN_1L" }, + + /* Right input selection to right PGA */ + { "Right PGA", NULL, "Right Input" }, + + /* Right PGA to right ADC */ + { "Right ADC", NULL, "Right PGA" }, + + /* Left DMic Input selection from switch */ + { "Left DMic Input", "Left ADC Capture Switch", "DMic_L" }, + + /* Left DMic to left ADC */ + { "Left ADC", NULL, "Left DMic Input" }, + + /* Right DMic Input selection from switch */ + { "Right DMic Input", "Right ADC Capture Switch", "DMic_R" }, + + /* Right DMic to right ADC */ + { "Right ADC", NULL, "Right DMic Input" }, + + /* ADC to AIF output */ + { "AIF_OUT", NULL, "Left ADC" }, + { "AIF_OUT", NULL, "Right ADC" }, + + /* Clocking */ + { "ADC_MOD_CLK", NULL, "ADC_CLK" }, + { "Left ADC", NULL, "ADC_MOD_CLK" }, + { "Right ADC", NULL, "ADC_MOD_CLK" }, + + { "BCLK", NULL, "ADC_CLK" }, +}; + +static const struct snd_soc_dapm_route adc3xxx_pll_intercon[] = { + { "ADC_CLK", NULL, "PLL_CLK" }, +}; + +static const struct snd_soc_dapm_route adc3xxx_bclk_out_intercon[] = { + { "AIF_OUT", NULL, "BCLK" } +}; + +static int adc3xxx_gpio_request(struct gpio_chip *chip, unsigned int offset) +{ + struct adc3xxx *adc3xxx = gpiochip_get_data(chip); + + if (offset >= ADC3XXX_GPIOS_MAX) + return -EINVAL; + + /* GPIO1 is offset 0, GPIO2 is offset 1 */ + /* We check here that the GPIO pins are either not configured in the + * DT, or that they purposely are set as outputs. + * (Input mode not yet implemented). + */ + if (adc3xxx->gpio_cfg[offset] != 0 && + adc3xxx->gpio_cfg[offset] != ADC3XXX_GPIO_GPO + 1) + return -EINVAL; + + return 0; +} + +static int adc3xxx_gpio_direction_out(struct gpio_chip *chip, + unsigned int offset, int value) +{ + struct adc3xxx *adc3xxx = gpiochip_get_data(chip); + + /* Set GPIO output function. */ + return regmap_update_bits(adc3xxx->regmap, + adc3xxx_gpio_ctrl_reg[offset], + ADC3XXX_GPIO_CTRL_CFG_MASK | + ADC3XXX_GPIO_CTRL_OUTPUT_CTRL_MASK, + ADC3XXX_GPIO_GPO << ADC3XXX_GPIO_CTRL_CFG_SHIFT | + !!value << ADC3XXX_GPIO_CTRL_OUTPUT_CTRL_SHIFT); +} + +/* With only GPIO outputs configured, we never get the .direction_out call, + * so we set the output mode and output value in the same call. Hence + * .set in practice does the same thing as .direction_out . + */ +static void adc3xxx_gpio_set(struct gpio_chip *chip, unsigned int offset, + int value) +{ + (void) adc3xxx_gpio_direction_out(chip, offset, value); +} + +/* Even though we only support GPIO output for now, some GPIO clients + * want to read the current pin state using the .get callback. + */ +static int adc3xxx_gpio_get(struct gpio_chip *chip, unsigned int offset) +{ + struct adc3xxx *adc3xxx = gpiochip_get_data(chip); + unsigned int regval; + int ret; + + /* We only allow output pins, so just read the value set in the output + * pin register field. + */ + ret = regmap_read(adc3xxx->regmap, adc3xxx_gpio_ctrl_reg[offset], &regval); + if (ret) + return ret; + return !!(regval & ADC3XXX_GPIO_CTRL_OUTPUT_CTRL_MASK); +} + +static const struct gpio_chip adc3xxx_gpio_chip = { + .label = "adc3xxx", + .owner = THIS_MODULE, + .request = adc3xxx_gpio_request, + .direction_output = adc3xxx_gpio_direction_out, + .set = adc3xxx_gpio_set, + .get = adc3xxx_gpio_get, + .can_sleep = 1, +}; + +static void adc3xxx_free_gpio(struct adc3xxx *adc3xxx) +{ + gpiochip_remove(&adc3xxx->gpio_chip); +} + +static void adc3xxx_init_gpio(struct adc3xxx *adc3xxx) +{ + int gpio, micbias; + int ret; + + adc3xxx->gpio_chip = adc3xxx_gpio_chip; + adc3xxx->gpio_chip.ngpio = ADC3XXX_GPIOS_MAX; + adc3xxx->gpio_chip.parent = adc3xxx->dev; + adc3xxx->gpio_chip.base = -1; + + ret = gpiochip_add_data(&adc3xxx->gpio_chip, adc3xxx); + if (ret) + dev_err(adc3xxx->dev, "Failed to add gpios: %d\n", ret); + + /* Set up potential GPIO configuration from the devicetree. + * This allows us to set up things which are not software + * controllable GPIOs, such as PDM microphone I/O, + */ + for (gpio = 0; gpio < ADC3XXX_GPIOS_MAX; gpio++) { + unsigned int cfg = adc3xxx->gpio_cfg[gpio]; + + if (cfg) { + cfg--; /* actual value to use is stored +1 */ + regmap_update_bits(adc3xxx->regmap, + adc3xxx_gpio_ctrl_reg[gpio], + ADC3XXX_GPIO_CTRL_CFG_MASK, + cfg << ADC3XXX_GPIO_CTRL_CFG_SHIFT); + } + } + + /* Set up micbias voltage */ + for (micbias = 0; micbias < ADC3XXX_MICBIAS_PINS; micbias++) { + unsigned int vg = adc3xxx->micbias_vg[micbias]; + + regmap_update_bits(adc3xxx->regmap, + ADC3XXX_MICBIAS_CTRL, + ADC3XXX_MICBIAS_MASK << adc3xxx_micbias_shift[micbias], + vg << adc3xxx_micbias_shift[micbias]); + } +} + +static int adc3xxx_parse_dt_gpio(struct adc3xxx *adc3xxx, + const char *propname, unsigned int *cfg) +{ + struct device *dev = adc3xxx->dev; + struct device_node *np = dev->of_node; + unsigned int val; + + if (!of_property_read_u32(np, propname, &val)) { + if (val & ~15 || val == 7 || val >= 11) { + dev_err(dev, "Invalid property value for '%s'\n", propname); + return -EINVAL; + } + if (val == ADC3XXX_GPIO_GPI) + dev_warn(dev, "GPIO Input read not yet implemented\n"); + *cfg = val + 1; /* 0 => not set up, all others shifted +1 */ + } + return 0; +} + +static int adc3xxx_parse_dt_micbias(struct adc3xxx *adc3xxx, + const char *propname, unsigned int *vg) +{ + struct device *dev = adc3xxx->dev; + struct device_node *np = dev->of_node; + unsigned int val; + + if (!of_property_read_u32(np, propname, &val)) { + if (val >= ADC3XXX_MICBIAS_AVDD) { + dev_err(dev, "Invalid property value for '%s'\n", propname); + return -EINVAL; + } + *vg = val; + } + return 0; +} + +static int adc3xxx_parse_pll_mode(uint32_t val, unsigned int *pll_mode) +{ + if (val != ADC3XXX_PLL_ENABLE && val != ADC3XXX_PLL_BYPASS && + val != ADC3XXX_PLL_AUTO) + return -EINVAL; + + *pll_mode = val; + + return 0; +} + +static void adc3xxx_setup_pll(struct snd_soc_component *component, + int div_entry) +{ + int i = div_entry; + + /* P & R values */ + snd_soc_component_write(component, ADC3XXX_PLL_PROG_PR, + (adc3xxx_divs[i].pll_p << ADC3XXX_PLLP_SHIFT) | + (adc3xxx_divs[i].pll_r << ADC3XXX_PLLR_SHIFT)); + /* J value */ + snd_soc_component_write(component, ADC3XXX_PLL_PROG_J, + adc3xxx_divs[i].pll_j & ADC3XXX_PLLJ_MASK); + /* D value */ + snd_soc_component_write(component, ADC3XXX_PLL_PROG_D_LSB, + adc3xxx_divs[i].pll_d & ADC3XXX_PLLD_LSB_MASK); + snd_soc_component_write(component, ADC3XXX_PLL_PROG_D_MSB, + (adc3xxx_divs[i].pll_d >> 8) & ADC3XXX_PLLD_MSB_MASK); +} + +static int adc3xxx_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_component *component = dai->component; + struct snd_soc_dapm_context *dapm = snd_soc_component_get_dapm(dai->component); + struct adc3xxx *adc3xxx = snd_soc_component_get_drvdata(component); + int i, width = 16; + u8 iface_len, bdiv; + + i = adc3xxx_get_divs(component->dev, adc3xxx->sysclk, + params_rate(params), adc3xxx->pll_mode); + + if (i < 0) + return i; + + /* select data word length */ + switch (params_format(params)) { + case SNDRV_PCM_FORMAT_S16_LE: + iface_len = ADC3XXX_IFACE_16BITS; + width = 16; + break; + case SNDRV_PCM_FORMAT_S20_3LE: + iface_len = ADC3XXX_IFACE_20BITS; + width = 20; + break; + case SNDRV_PCM_FORMAT_S24_LE: + iface_len = ADC3XXX_IFACE_24BITS; + width = 24; + break; + case SNDRV_PCM_FORMAT_S32_LE: + iface_len = ADC3XXX_IFACE_32BITS; + width = 32; + break; + default: + dev_err(component->dev, "Unsupported serial data format\n"); + return -EINVAL; + } + snd_soc_component_update_bits(component, ADC3XXX_INTERFACE_CTRL_1, + ADC3XXX_WLENGTH_MASK, iface_len); + if (adc3xxx_divs[i].pll_p) { /* If PLL used for this mode */ + adc3xxx_setup_pll(component, i); + snd_soc_component_write(component, ADC3XXX_CLKGEN_MUX, ADC3XXX_USE_PLL); + if (!adc3xxx->use_pll) { + snd_soc_dapm_add_routes(dapm, adc3xxx_pll_intercon, + ARRAY_SIZE(adc3xxx_pll_intercon)); + adc3xxx->use_pll = 1; + } + } else { + snd_soc_component_write(component, ADC3XXX_CLKGEN_MUX, ADC3XXX_NO_PLL); + if (adc3xxx->use_pll) { + snd_soc_dapm_del_routes(dapm, adc3xxx_pll_intercon, + ARRAY_SIZE(adc3xxx_pll_intercon)); + adc3xxx->use_pll = 0; + } + } + + /* NADC */ + snd_soc_component_update_bits(component, ADC3XXX_ADC_NADC, + ADC3XXX_NADC_MASK, adc3xxx_divs[i].nadc); + /* MADC */ + snd_soc_component_update_bits(component, ADC3XXX_ADC_MADC, + ADC3XXX_MADC_MASK, adc3xxx_divs[i].madc); + /* AOSR */ + snd_soc_component_update_bits(component, ADC3XXX_ADC_AOSR, + ADC3XXX_AOSR_MASK, adc3xxx_divs[i].aosr); + /* BDIV N Value */ + /* BCLK is (by default) set up to be derived from ADC_CLK */ + bdiv = (adc3xxx_divs[i].aosr * adc3xxx_divs[i].madc) / (2 * width); + snd_soc_component_update_bits(component, ADC3XXX_BCLK_N_DIV, + ADC3XXX_BDIV_MASK, bdiv); + + return 0; +} + +static const char *adc3xxx_pll_mode_text(int pll_mode) +{ + switch (pll_mode) { + case ADC3XXX_PLL_AUTO: + return "PLL auto"; + case ADC3XXX_PLL_ENABLE: + return "PLL enable"; + case ADC3XXX_PLL_BYPASS: + return "PLL bypass"; + default: + break; + } + + return "PLL unknown"; +} + +static int adc3xxx_set_dai_sysclk(struct snd_soc_dai *codec_dai, + int clk_id, unsigned int freq, int dir) +{ + struct snd_soc_component *component = codec_dai->component; + struct adc3xxx *adc3xxx = snd_soc_component_get_drvdata(component); + int ret; + + ret = adc3xxx_parse_pll_mode(clk_id, &adc3xxx->pll_mode); + if (ret < 0) + return ret; + + adc3xxx->sysclk = freq; + dev_dbg(component->dev, "Set sysclk to %u Hz, %s\n", + freq, adc3xxx_pll_mode_text(adc3xxx->pll_mode)); + return 0; +} + +static int adc3xxx_set_dai_fmt(struct snd_soc_dai *codec_dai, unsigned int fmt) +{ + struct snd_soc_component *component = codec_dai->component; + struct snd_soc_dapm_context *dapm = snd_soc_component_get_dapm(component); + struct adc3xxx *adc3xxx = snd_soc_component_get_drvdata(component); + u8 clkdir = 0, format = 0; + int master = 0; + + /* set master/slave audio interface */ + switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { + case SND_SOC_DAIFMT_CBP_CFP: + master = 1; + clkdir = ADC3XXX_BCLK_MASTER | ADC3XXX_WCLK_MASTER; + break; + case SND_SOC_DAIFMT_CBC_CFC: + master = 0; + break; + default: + dev_err(component->dev, "Invalid DAI clock setup\n"); + return -EINVAL; + } + + /* + * match both interface format and signal polarities since they + * are fixed + */ + switch (fmt & (SND_SOC_DAIFMT_FORMAT_MASK | SND_SOC_DAIFMT_INV_MASK)) { + case SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF: + format = ADC3XXX_FORMAT_I2S; + break; + case SND_SOC_DAIFMT_DSP_A | SND_SOC_DAIFMT_IB_NF: + format = ADC3XXX_FORMAT_DSP; + break; + case SND_SOC_DAIFMT_DSP_B | SND_SOC_DAIFMT_IB_NF: + format = ADC3XXX_FORMAT_DSP; + break; + case SND_SOC_DAIFMT_RIGHT_J | SND_SOC_DAIFMT_NB_NF: + format = ADC3XXX_FORMAT_RJF; + break; + case SND_SOC_DAIFMT_LEFT_J | SND_SOC_DAIFMT_NB_NF: + format = ADC3XXX_FORMAT_LJF; + break; + default: + dev_err(component->dev, "Invalid DAI format\n"); + return -EINVAL; + } + + /* Add/del route enabling BCLK output as applicable */ + if (master && !adc3xxx->master) + snd_soc_dapm_add_routes(dapm, adc3xxx_bclk_out_intercon, + ARRAY_SIZE(adc3xxx_bclk_out_intercon)); + else if (!master && adc3xxx->master) + snd_soc_dapm_del_routes(dapm, adc3xxx_bclk_out_intercon, + ARRAY_SIZE(adc3xxx_bclk_out_intercon)); + adc3xxx->master = master; + + /* set clock direction and format */ + return snd_soc_component_update_bits(component, + ADC3XXX_INTERFACE_CTRL_1, + ADC3XXX_CLKDIR_MASK | ADC3XXX_FORMAT_MASK, + clkdir | format); +} + +static const struct snd_soc_dai_ops adc3xxx_dai_ops = { + .hw_params = adc3xxx_hw_params, + .set_sysclk = adc3xxx_set_dai_sysclk, + .set_fmt = adc3xxx_set_dai_fmt, +}; + +static struct snd_soc_dai_driver adc3xxx_dai = { + .name = "tlv320adc3xxx-hifi", + .capture = { + .stream_name = "Capture", + .channels_min = 1, + .channels_max = 2, + .rates = ADC3XXX_RATES, + .formats = ADC3XXX_FORMATS, + }, + .ops = &adc3xxx_dai_ops, +}; + +static const struct snd_soc_component_driver soc_component_dev_adc3xxx = { + .controls = adc3xxx_snd_controls, + .num_controls = ARRAY_SIZE(adc3xxx_snd_controls), + .dapm_widgets = adc3xxx_dapm_widgets, + .num_dapm_widgets = ARRAY_SIZE(adc3xxx_dapm_widgets), + .dapm_routes = adc3xxx_intercon, + .num_dapm_routes = ARRAY_SIZE(adc3xxx_intercon), +}; + +static int adc3xxx_i2c_probe(struct i2c_client *i2c, + const struct i2c_device_id *id) +{ + struct device *dev = &i2c->dev; + struct adc3xxx *adc3xxx = NULL; + int ret; + + adc3xxx = devm_kzalloc(dev, sizeof(struct adc3xxx), GFP_KERNEL); + if (!adc3xxx) + return -ENOMEM; + adc3xxx->dev = dev; + + adc3xxx->rst_pin = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(adc3xxx->rst_pin)) { + return dev_err_probe(dev, PTR_ERR(adc3xxx->rst_pin), + "Failed to request rst_pin\n"); + } + + adc3xxx->mclk = devm_clk_get(dev, NULL); + if (IS_ERR(adc3xxx->mclk)) { + /* + * The chip itself supports running off the BCLK either + * directly or via the PLL, but the driver does not (yet), so + * having a specified mclk is required. Otherwise, we could + * use the lack of a clocks property to indicate when BCLK is + * intended as the clock source. + */ + return dev_err_probe(dev, PTR_ERR(adc3xxx->mclk), + "Failed to acquire MCLK\n"); + } else if (adc3xxx->mclk) { + ret = clk_prepare_enable(adc3xxx->mclk); + if (ret < 0) + return ret; + dev_dbg(dev, "Enabled MCLK, freq %lu Hz\n", clk_get_rate(adc3xxx->mclk)); + } + + ret = adc3xxx_parse_dt_gpio(adc3xxx, "ti,dmdin-gpio1", &adc3xxx->gpio_cfg[0]); + if (ret < 0) + return ret; + ret = adc3xxx_parse_dt_gpio(adc3xxx, "ti,dmclk-gpio2", &adc3xxx->gpio_cfg[1]); + if (ret < 0) + return ret; + ret = adc3xxx_parse_dt_micbias(adc3xxx, "ti,micbias1-vg", &adc3xxx->micbias_vg[0]); + if (ret < 0) + return ret; + ret = adc3xxx_parse_dt_micbias(adc3xxx, "ti,micbias2-vg", &adc3xxx->micbias_vg[1]); + if (ret < 0) + return ret; + + adc3xxx->regmap = devm_regmap_init_i2c(i2c, &adc3xxx_regmap); + if (IS_ERR(adc3xxx->regmap)) { + ret = PTR_ERR(adc3xxx->regmap); + return ret; + } + + i2c_set_clientdata(i2c, adc3xxx); + + adc3xxx->type = id->driver_data; + + /* Reset codec chip */ + gpiod_set_value_cansleep(adc3xxx->rst_pin, 1); + usleep_range(2000, 100000); /* Requirement: > 10 ns (datasheet p13) */ + gpiod_set_value_cansleep(adc3xxx->rst_pin, 0); + + /* Potentially set up pins used as GPIOs */ + adc3xxx_init_gpio(adc3xxx); + + ret = snd_soc_register_component(dev, + &soc_component_dev_adc3xxx, &adc3xxx_dai, 1); + if (ret < 0) + dev_err(dev, "Failed to register codec: %d\n", ret); + + return ret; +} + +static int __exit adc3xxx_i2c_remove(struct i2c_client *client) +{ + struct adc3xxx *adc3xxx = i2c_get_clientdata(client); + + if (adc3xxx->mclk) + clk_disable_unprepare(adc3xxx->mclk); + adc3xxx_free_gpio(adc3xxx); + snd_soc_unregister_component(&client->dev); + return 0; +} + +static const struct of_device_id tlv320adc3xxx_of_match[] = { + { .compatible = "ti,tlv320adc3001", }, + { .compatible = "ti,tlv320adc3101", }, + {}, +}; +MODULE_DEVICE_TABLE(of, tlv320adc3xxx_of_match); + +static const struct i2c_device_id adc3xxx_i2c_id[] = { + { "tlv320adc3001", ADC3001 }, + { "tlv320adc3101", ADC3101 }, + {} +}; +MODULE_DEVICE_TABLE(i2c, adc3xxx_i2c_id); + +static struct i2c_driver adc3xxx_i2c_driver = { + .driver = { + .name = "tlv320adc3xxx-codec", + .of_match_table = tlv320adc3xxx_of_match, + }, + .probe = adc3xxx_i2c_probe, + .remove = adc3xxx_i2c_remove, + .id_table = adc3xxx_i2c_id, +}; + +module_i2c_driver(adc3xxx_i2c_driver); + +MODULE_DESCRIPTION("ASoC TLV320ADC3xxx codec driver"); +MODULE_AUTHOR("shahina.s(a)mistralsolutions.com"); +MODULE_LICENSE("GPL v2"); -- 2.20.1 -- Ricard Wolf Wanderlof ricardw(at)axis.com Axis Communications AB, Lund, Sweden www.axis.com Phone +46 46 272 2016 Fax +46 46 13 61 30

2 1

[PATCH 0/5] ASoC: Intel: catpt: Dma-transfer fix and couple
by Cezary Rojewski 21 Dec '21

21 Dec '21

Set is made of one fix for dma-transfer so that result of dmaengine_submit() is tested before moving on, and few cleanups: - two non-impactful, where catpt_component_open() layout gets improved slightly as well as relocation of couple of locals found in PCM-functions so that they look more cohesive - no need to expose catpt-driver board-matching information globally. Most fields are not by it and it's the sole user of haswell_machines table. By having them locally it is clear what is actually being used Cezary Rojewski (5): ASoC: Intel: catpt: Test dmaengine_submit() result before moving on ASoC: Intel: catpt: Reduce size of catpt_component_open() ASoC: Intel: catpt: Streamline locals declaration for PCM-functions ASoC: Intel: catpt: Drop SND_SOC_ACPI_INTEL_MATCH dependency ASoC: Intel: Drop legacy HSW/BDW board-match information include/sound/soc-acpi-intel-match.h | 1 - sound/soc/intel/Kconfig | 2 +- sound/soc/intel/catpt/device.c | 33 +++++++++++++++-- sound/soc/intel/catpt/dsp.c | 14 ++++++- sound/soc/intel/catpt/pcm.c | 37 +++++++++---------- .../common/soc-acpi-intel-hsw-bdw-match.c | 16 -------- 6 files changed, 61 insertions(+), 42 deletions(-) -- 2.25.1

3 14

[PATCH] ASoC: sh: rz-ssi: Check return value of pm_runtime_resume_and_get()
by Heiner Kallweit 21 Dec '21

21 Dec '21

The return value of pm_runtime_resume_and_get() needs to be checked to avoid a usage count imbalance in the error case. This fix is basically the same as 92c959bae2e5 ("reset: renesas: Fix Runtime PM usage"), and the last step before pm_runtime_resume_and_get() can be annotated as __must_check. Fixes: 03e786bd4341 ("ASoC: sh: Add RZ/G2L SSIF-2 driver") Cc: stable(a)vger.kernel.org Signed-off-by: Heiner Kallweit <hkallweit1(a)gmail.com> --- sound/soc/sh/rz-ssi.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/sound/soc/sh/rz-ssi.c b/sound/soc/sh/rz-ssi.c index fa0cc08f7..850387dd8 100644 --- a/sound/soc/sh/rz-ssi.c +++ b/sound/soc/sh/rz-ssi.c @@ -1020,7 +1020,12 @@ static int rz_ssi_probe(struct platform_device *pdev) reset_control_deassert(ssi->rstc); pm_runtime_enable(&pdev->dev); - pm_runtime_resume_and_get(&pdev->dev); + ret = pm_runtime_resume_and_get(&pdev->dev); + if (ret < 0) { + pm_runtime_disable(ssi->dev); + reset_control_assert(ssi->rstc); + return dev_err_probe(ssi->dev, ret, "pm_runtime_resume_and_get failed\n"); + } spin_lock_init(&ssi->lock); dev_set_drvdata(&pdev->dev, ssi); -- 2.34.1

2 1

[PATCH v4 00/22] Support HDMI audio on NVIDIA Tegra20
by Dmitry Osipenko 21 Dec '21

21 Dec '21

This series revives Tegra20 S/PDIF driver which was upstreamed long time ago, but never was used. It also turns Tegra DRM HDMI driver into HDMI audio CODEC provider. Finally, HDMI audio is enabled in device-trees. For now the audio is enable only for Acer A500 tablet and Toshiba AC100 netbook because they're already supported by upstream, later on ASUS TF101 tablet will join them. I based S/PDIF patches on Arnd's Bergmann patch from a separate series [1] that removes obsolete slave_id. This eases merging of the patches by removing the merge conflict. This is a note for Mark Brown. I also based this series on top of power management series [2]. I.e. [2] should be applied first, otherwise "Add S/PDIF node to Tegra20 device-tree" patch should have merge conflict. This is a note for Thierry. [1] https://patchwork.ozlabs.org/project/linux-tegra/list/?series=273312 [2] https://patchwork.ozlabs.org/project/linux-tegra/list/?series=274534 Changelog: v4: - Added patches that update multi_v7_defconfig with the enabled S/PDIF and APB DMA drivers. v3: - Renamed S/PDIF device-tree clocks as was suggested by Rob Herring. - Added r-bs and acks that were given by Rob Herring to v2. v2: - Corrected I2S yaml problem that was reported by the DT bot for v1 by removing the non-existent required clock-names property. - Removed assigned-clocks property from S/PDIF yaml since this property is now inherited from the clocks property. - Reordered the "tegra20: spdif: Set FIFO trigger level" patch, making it the first sound/soc patch in the series, like it was suggested by Mark Brown in the comment to v1. Also reworded commit message of this patch to *not* make it looks like it should be backported to stable kernels. Arnd Bergmann (1): ASoC: tegra20-spdif: stop setting slave_id Dmitry Osipenko (21): ASoC: dt-bindings: Add binding for Tegra20 S/PDIF ASoC: dt-bindings: tegra20-i2s: Convert to schema ASoC: dt-bindings: tegra20-i2s: Document new nvidia,fixed-parent-rate property dt-bindings: host1x: Document optional HDMI sound-dai-cells ASoC: tegra20: spdif: Set FIFO trigger level ASoC: tegra20: spdif: Support device-tree ASoC: tegra20: spdif: Improve driver's code ASoC: tegra20: spdif: Use more resource-managed helpers ASoC: tegra20: spdif: Reset hardware ASoC: tegra20: spdif: Support system suspend ASoC: tegra20: spdif: Filter out unsupported rates ASoC: tegra20: i2s: Filter out unsupported rates drm/tegra: hdmi: Unwind tegra_hdmi_init() errors drm/tegra: hdmi: Register audio CODEC on Tegra20 ARM: tegra_defconfig: Enable S/PDIF driver ARM: config: multi v7: Enable NVIDIA Tegra20 S/PDIF driver ARM: config: multi v7: Enable NVIDIA Tegra20 APB DMA driver ARM: tegra: Add S/PDIF node to Tegra20 device-tree ARM: tegra: Add HDMI audio graph to Tegra20 device-tree ARM: tegra: acer-a500: Enable S/PDIF and HDMI audio ARM: tegra: paz00: Enable S/PDIF and HDMI audio .../display/tegra/nvidia,tegra20-host1x.txt | 1 + .../bindings/sound/nvidia,tegra20-i2s.txt | 30 --- .../bindings/sound/nvidia,tegra20-i2s.yaml | 77 +++++++ .../bindings/sound/nvidia,tegra20-spdif.yaml | 85 ++++++++ .../boot/dts/tegra20-acer-a500-picasso.dts | 8 + arch/arm/boot/dts/tegra20-paz00.dts | 8 + arch/arm/boot/dts/tegra20.dtsi | 40 +++- arch/arm/configs/multi_v7_defconfig | 2 + arch/arm/configs/tegra_defconfig | 1 + drivers/gpu/drm/tegra/Kconfig | 3 + drivers/gpu/drm/tegra/hdmi.c | 168 +++++++++++++-- sound/soc/tegra/tegra20_i2s.c | 49 +++++ sound/soc/tegra/tegra20_spdif.c | 197 ++++++++++++------ sound/soc/tegra/tegra20_spdif.h | 1 + sound/soc/tegra/tegra_pcm.c | 6 + sound/soc/tegra/tegra_pcm.h | 1 + 16 files changed, 574 insertions(+), 103 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.txt create mode 100644 Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.yaml create mode 100644 Documentation/devicetree/bindings/sound/nvidia,tegra20-spdif.yaml -- 2.33.1

4 50