August 2007 - Alsa-devel - mailman.alsa-project.org

[alsa-devel] HDA - Add more support for Dell systems.
by Tobin Davis 21 Aug '07

21 Aug '07

This patch adds support for more Dell systems with Sigmatel/IDT codecs. Signed off by Tobin Davis <tdavis(a)dsl-only.net>

3 11

[alsa-devel] ESI MAYA44 PCI - ESI wants to collaborate!
by Piotrek 21 Aug '07

21 Aug '07

Referring to the lack of the official ALSA support of ESI MAYA44 PCI (in fact, the card does not work) I would like to ask I there are any plans to get this card working with ALSA? I would be thankful to be able to run my soundcard properly under Linux. There are also a lot of people that would appreciate your work and are waiting for maya44 pci drivers for linux: http://www.esiforum.com/show.asp?db=esi&t=esi1&mode=3&msg=793 I wrote a letter to the UK ESI SUPPORT asking if they were going to write drivers for their products for Linux systems as well. There is a reply: " Dear Piotr ESI do not provide and have no plans for Linux drivers for our products However ESI are happy to provide /share information to an Individual developer within the Linux community That is able and capable to develope drivers and wishes to develope drivers Regards UK Support ESI Auditechnik " It means that ESI will collaborate with developers who would like to write such driver and share the documentation. Again the question: Are there any plans to make ESI MAYA44 PCI card working with ALSA? I'm not a programmer but I will help you as much as I could. -- Best Regards, Piotr Makowski

4 4

[alsa-devel] Intel HDA / AD1986A problems
by Peter Skensved 21 Aug '07

21 Aug '07

Configuration : Lenovo 3000 N100 laptop with Intel HDA / Anlog Devices AD1986A soundcard running CentOS5.0 with 2.6.18-8.1.8.el5 kernel ( uses 1.0.12rc1 based alsa driver ). The driver works with the model=laptop-eapd option except for a few things : 1) Plugging in an external headset will not mute the internal speakers ( has to be done manually in alsa-mixer ) 2) The PC speaker ( bell ) appears to be permanently muted. 3) The external microphone input does not appear to be working no matter what I do. 4) When recording from the internal microphone the level is very, very low and almost drowns in static noise. Any easy way to fix the above ? Number 4 in particular ? I've tinkered with backporting what I thought were relevant differences between the latest patch_analog.c and the one used in the kernel I have (alsa-driver 1.0.12rc1 ) but I see no difference. Any other way to tweak or reconfigure the hardware ? Enable microphone boost ?? Looking at /proc/asound/card0/codec#0 makes me believe that the hardware has several unused or permanently disabled features. This particular laptop has a model number which differs slightly from the one listed in patch_analog.c ( 0768-6KU instead of 0768-4JU ). Not sure if is relevant. And finally a ( somewhat ) related question : Is it possible to get the sound card to work with the slmodem package to drive the built in modem ??? ============================================================================================ Partial output from lspci -nv is attached below together with stuff from /proc/asound : 00:1b.0 0403: 8086:27d8 (rev 02) Subsystem: 17aa:2066 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 233 Region 0: Memory at b0000000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [70] Express Unknown type IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <64ns, L1 <1us Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0 Link: Latency L0s <64ns, L1 <1us Link: ASPM Disabled CommClk- ExtSynch- Link: Speed unknown, Width x0 Capabilities: [100] Virtual Channel Capabilities: [130] Unknown (5) more /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xb0000000 irq 233 more /proc/asound/devices 2: : timer 3: : sequencer 4: [ 0- 0]: digital audio playback 5: [ 0- 0]: digital audio capture 6: [ 0] : control more /proc/asound/modules 0 snd_hda_intel more /proc/asound/card0/codec#0 Codec: Analog Devices AD1986A Address: 0 Vendor Id: 0x11d41986 Subsystem Id: 0x17aa2066 Revision Id: 0x100500 Default PCM: rates 0x07f, bits 0x0e, types 0x1 Default Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Default Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=1 Node 0x02 [Audio Output] wcaps 0x30311: Stereo Digital PCM: rates 0x060, bits 0x02, types 0x5 Connection: 2 0x01* 0x06 Node 0x03 [Audio Output] wcaps 0x44d: Stereo Amp-Out Amp-Out caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1 Amp-Out vals: [0x1d 0x1d] Power: 0x0 Node 0x04 [Audio Output] wcaps 0x40d: Stereo Amp-Out Amp-Out caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1 Amp-Out vals: [0x80 0x80] Power: 0x0 Node 0x05 [Audio Output] wcaps 0x40d: Stereo Amp-Out Amp-Out caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1 Amp-Out vals: [0x80 0x80] Power: 0x0 Node 0x06 [Audio Input] wcaps 0x100511: Stereo PCM: rates 0x07f, bits 0x06, types 0x1 Power: 0x0 Connection: 1 0x12 Node 0x07 [Audio Mixer] wcaps 0x200101: Stereo Connection: 8 0x03 0x09 0x13 0x14 0x15 0x16 0x17 0x18 Node 0x08 [Audio Mixer] wcaps 0x200100: Mono Connection: 1 0x07 Node 0x09 [Audio Mixer] wcaps 0x20010e: Mono Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x80] [0x80] Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80] Connection: 2 0x04 0x05 Node 0x0a [Audio Selector] wcaps 0x300101: Stereo Connection: 3 0x07* 0x04 0x05 Node 0x0b [Audio Selector] wcaps 0x300101: Stereo Connection: 2 0x07* 0x04 Node 0x0c [Audio Selector] wcaps 0x300101: Stereo Connection: 2 0x04* 0x07 Node 0x0d [Audio Selector] wcaps 0x300101: Stereo Connection: 2 0x05* 0x08 Node 0x0e [Audio Selector] wcaps 0x300100: Mono Connection: 2 0x08* 0x11 Node 0x0f [Audio Selector] wcaps 0x30010d: Stereo Amp-Out Amp-Out caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 Amp-Out vals: [0x00 0x00] Connection: 8 0x1f* 0x20 0x1d 0x1d 0x27 0x28 0x29 0x2a Node 0x10 [Audio Selector] wcaps 0x300101: Stereo Connection: 3 0x20* 0x1c 0x1f Node 0x11 [Audio Selector] wcaps 0x300941: Stereo Connection: 2 0x0f* 0x2b Node 0x12 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out Amp-Out caps: ofs=0x00, nsteps=0x0f, stepsize=0x05, mute=1 Amp-Out vals: [0x8f 0x8f] Connection: 8 0x11 0x22 0x00 0x21 0x10 0x07* 0x08 0x23 Node 0x13 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out Amp-Out caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1 Amp-Out vals: [0x1d 0x1d] Connection: 1 0x11 Node 0x14 [Audio Selector] wcaps 0x30010c: Mono Amp-Out Amp-Out caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1 Amp-Out vals: [0x80] Connection: 1 0x23 Node 0x15 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out Amp-Out caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1 Amp-Out vals: [0x80 0x80] Connection: 1 0x22 Node 0x16 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out Amp-Out caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1 Amp-Out vals: [0x80 0x80] Connection: 1 0x21 Node 0x17 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out Amp-Out caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1 Amp-Out vals: [0x15 0x15] Connection: 1 0x10 Node 0x18 [Audio Selector] wcaps 0x30010c: Mono Amp-Out Amp-Out caps: ofs=0x0f, nsteps=0x0f, stepsize=0x0b, mute=1 Amp-Out vals: [0x8f] Connection: 2 0x19* 0x24 Node 0x19 [Beep Generator Widget] wcaps 0x700000: Mono Node 0x1a [Pin Complex] wcaps 0x400185: Stereo Amp-Out Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=1 Amp-Out vals: [0x06 0x06] Pincap 0x081f: OUT HP Detect Pin Default 0x02214021: [Jack] HP Out at Ext Front Conn = 1/8, Color = Green Pin-ctls: 0xc0: OUT HP Connection: 1 0x0a Node 0x1b [Pin Complex] wcaps 0x400185: Stereo Amp-Out Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=1 Amp-Out vals: [0x06 0x06] Pincap 0x081001f: OUT HP EAPD Detect Pin Default 0x81114011: [Fixed] Speaker at Ext Rear Conn = 1/8, Color = Green Pin-ctls: 0x40: OUT Connection: 1 0x0b Node 0x1c [Pin Complex] wcaps 0x400185: Stereo Amp-Out Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=1 Amp-Out vals: [0x80 0x80] Pincap 0x0837: IN OUT Detect Pin Default 0x41013012: [N/A] Line Out at Ext Rear Conn = 1/8, Color = Blue Pin-ctls: 0x40: OUT Connection: 1 0x0c Node 0x1d [Pin Complex] wcaps 0x400985: Stereo Amp-Out Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=1 Amp-Out vals: [0x80 0x80] Pincap 0x081737: IN OUT Detect Pin Default 0x41019015: [N/A] Line Out at Ext Rear Conn = 1/8, Color = Pink Pin-ctls: 0x40: OUT Connection: 1 0x0d Node 0x1e [Pin Complex] wcaps 0x400104: Mono Amp-Out Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=1 Amp-Out vals: [0x80] Pincap 0x0810: OUT Pin Default 0x501700f0: [N/A] Speaker at Int N/A Conn = Analog, Color = Unknown Pin-ctls: 0x40: OUT Connection: 1 0x0e Node 0x1f [Pin Complex] wcaps 0x400081: Stereo Pincap 0x081727: IN Detect Pin Default 0xc2a190f0: [Both] Mic at Ext Front Conn = 1/8, Color = Pink Pin-ctls: 0x24: IN Node 0x20 [Pin Complex] wcaps 0x400081: Stereo Pincap 0x081727: IN Detect Pin Default 0x418130f0: [N/A] Line In at Ext Rear Conn = 1/8, Color = Blue Pin-ctls: 0x20: IN Node 0x21 [Pin Complex] wcaps 0x400081: Stereo Pincap 0x0827: IN Detect Pin Default 0x509700f0: [N/A] Aux at Int N/A Conn = Analog, Color = Unknown Pin-ctls: 0x20: IN Node 0x22 [Pin Complex] wcaps 0x400001: Stereo Pincap 0x0820: IN Pin Default 0x903300f0: [Fixed] CD at Int N/A Conn = ATAPI, Color = Unknown Pin-ctls: 0x20: IN Node 0x23 [Pin Complex] wcaps 0x400000: Mono Pincap 0x0820: IN Pin Default 0x90b70130: [Fixed] Telephony at Int N/A Conn = Analog, Color = Unknown Pin-ctls: 0x20: IN Node 0x24 [Pin Complex] wcaps 0x400000: Mono Pincap 0x0820: IN Pin Default 0x90f701f0: [Fixed] Other at Int N/A Conn = Analog, Color = Unknown Pin-ctls: 0x20: IN Node 0x25 [Pin Complex] wcaps 0x400301: Stereo Digital Pincap 0x0810: OUT Pin Default 0x014511f0: [Jack] SPDIF Out at Ext Rear Conn = Optical, Color = Black Pin-ctls: 0x40: OUT Connection: 1 0x02 Node 0x26 [Power Widget] wcaps 0x500500: Mono Power: 0x0 Connection: 8 0x07* 0x08 0x13 0x14 0x15 0x16 0x17 0x18 Node 0x27 [Audio Mixer] wcaps 0x200101: Stereo Connection: 2 0x1f 0x1d Node 0x28 [Audio Mixer] wcaps 0x200101: Stereo Connection: 2 0x1f 0x20 Node 0x29 [Audio Mixer] wcaps 0x200101: Stereo Connection: 2 0x1d 0x20 Node 0x2a [Audio Mixer] wcaps 0x200101: Stereo Connection: 3 0x1f 0x1d 0x20 Node 0x2b [Audio Mixer] wcaps 0x200100: Mono Connection: 1 0x0f more /proc/asound/card0/codec#1 Codec: Generic 11c1 ID 1040 Address: 1 Vendor Id: 0x11c11040 Subsystem Id: 0x11c10001 Revision Id: 0x100200 more /proc/asound/card0/pcm0c/info card: 0 device: 0 subdevice: 0 stream: CAPTURE id: AD198x Analog name: AD198x Analog subname: subdevice #0 class: 0 subclass: 0 subdevices_count: 1 subdevices_avail: 1 more /proc/asound/card0/pcm0p/info card: 0 device: 0 subdevice: 0 stream: PLAYBACK id: AD198x Analog name: AD198x Analog subname: subdevice #0 class: 0 subclass: 0 subdevices_count: 1 subdevices_avail: 1 amixer scontents Simple mixer control 'Master',0 Capabilities: pvolume pswitch Playback channels: Front Left - Front Right Limits: Playback 0 - 31 Mono: Front Left: Playback 12 [39%] [on] Front Right: Playback 12 [39%] [on] Simple mixer control 'PCM',0 Capabilities: pvolume pswitch Playback channels: Front Left - Front Right Limits: Playback 0 - 31 Mono: Front Left: Playback 29 [94%] [on] Front Right: Playback 29 [94%] [on] Simple mixer control 'Mic',0 Capabilities: pvolume pswitch cswitch cswitch-joined cswitch-exclusive Capture exclusive group: 0 Playback channels: Front Left - Front Right Capture channels: Mono Limits: Playback 0 - 31 Mono: Capture [on] Front Left: Playback 29 [94%] [on] Front Right: Playback 29 [94%] [on] Simple mixer control 'Capture',0 Capabilities: cvolume cswitch Capture channels: Front Left - Front Right Limits: Capture 0 - 15 Front Left: Capture 15 [100%] [on] Front Right: Capture 15 [100%] [on] Simple mixer control 'Mix',0 Capabilities: cswitch cswitch-joined cswitch-exclusive Capture exclusive group: 0 Capture channels: Mono Mono: Capture [off] Simple mixer control 'External Amplifier',0 Capabilities: pswitch pswitch-joined Playback channels: Mono Mono: Playback [on] Simple mixer control 'Internal Mic',0 Capabilities: pvolume pswitch cswitch cswitch-joined cswitch-exclusive Capture exclusive group: 0 Playback channels: Front Left - Front Right Capture channels: Mono Limits: Playback 0 - 31 Mono: Capture [off] Front Left: Playback 15 [48%] [on] Front Right: Playback 15 [48%] [on] ======================================================================================= Peter Skensved Email : peter at SNO dot Phy dot QueensU dot CA Dept. of Physics, Queen's University, Kingston, Ontario, Canada

2 1

Re: [alsa-devel] ESI MAYA44 PCI - ESI wants to collaborate!
by Ash Willis 21 Aug '07

21 Aug '07

Hi Piotrek, Thanks for being so active in trying to improve ALSA support. I've written a couple of these drivers too but someone better than me should do this ;) especially if ESI is only willing to discuss this matter with one developer. Besides, I don't fancy paying £70 for the opportunity. The people at ESI will know what they need to provide: A full datasheet containing things like IO port layout, register descriptions and commands. Source code for current Windows drivers would be helpful but not essential. If the card needs firmware, then we'll need that too. It's also not essential that the source code for the firmware is provided but I think that's probably preferred as well. In either case, ESI will need to give permission for the firmware to be distributed for it to be well supported by ALSA. Otherwise, users will be responsible for extracting the firmware from their Windows drivers, and that's just not nice. Like I said, ESI will know will they need to provide: that is to say all the information they gave to their programmers to let them create the current drivers for this device. It is clear by the ESI response that they are willing to release the information on the provision that a good driver will be produced thereby making them look good. That is fair enough. I would suggest to ESI, however, that to truly create the maximum possibility of this happening, they could allow the datasheet to be held on the ALSA server. By doing this, the relevant information would be available to any developer who wanted to create the driver or make further improvements. You can point them to the address below if they don't think that sounds like something a sane company would do. http://ftp.mj2.org/pub/alsa/datasheets/ Anyway, good luck and my advice would be to try and get the info first and find a developer later. I don't know if ESI will do that though. There will always be people, floating around, who will code this up, but there's no guaranty that the company will always be as happy and friendly as they were to you :) Ash > ----- Original Message ----- > From: Piotrek <oponek(a)gmail.com> > To: "Adrian McMenamin" <adrianmcmenamin(a)gmail.com> > Subject: Re: [alsa-devel] ESI MAYA44 PCI - ESI wants to collaborate! > Date: Mon, 20 Aug 2007 22:53:53 +0200 > > > 2007/8/20, Adrian McMenamin <adrianmcmenamin(a)gmail.com>: > > > > On 20/08/07, Takashi Iwai <tiwai(a)suse.de> wrote: > > > At Sat, 18 Aug 2007 09:28:34 +0200, > > > Piotrek wrote: > > > > > > > > Referring to the lack of the official ALSA support of ESI MAYA44 > > PCI > > > > (in fact, the card does not work) I would like to ask I there are any > > plans > > > > to get this card working with ALSA? I would be thankful to be able to > > run my > > > > soundcard properly under Linux. There are also a lot of people that > > would > > > > appreciate your work and are waiting for maya44 pci drivers for linux: > > > > http://www.esiforum.com/show.asp?db=esi&t=esi1&mode=3&msg=793 > > > > I wrote a letter to the UK ESI SUPPORT asking if they were going > > to > > > > write drivers for their products for Linux systems as well. There is a > > > > reply: > > > > > > > > " > > > > Dear Piotr > > > > > > > > ESI do not provide and have no plans for Linux drivers for our > > products > > > > However > > > > ESI are happy to provide /share information to an Individual developer > > > > within the Linux community > > > > That is able and capable to develope drivers > > > > and wishes to develope drivers > > > > > > > > Regards > > > > UK Support > > > > ESI Auditechnik > > > > " > > > > > > > > It means that ESI will collaborate with developers who would like to > > write > > > > such driver and share the documentation. > > > > > > > > Again the question: Are there any plans to make ESI MAYA44 PCI card > > working > > > > with ALSA? > > > > > > AFAIK, no plan. We don't have this hardware for developing. > > > > > > > > > > I have no idea what this card is like, but if they would be prepared > > to send me one, I'd be happy to take the project on. I've written one > > alsa driver - that will shortly be in the stable kernel - so can point > > to that. > > > > Of course, other developers will probably be able to do the job at a > > greater speed - but I would be happy to take it on as a pro bono > > project. > > > > I am in the UK. > > > > Thank you all for your replies. I think we should wait a while for the > response of the rest of the ALSA dev team and then we would be able to > choose the best person for this quest and decide what to do with it > together. > However, we need to > specify what kind of information do we exactly need form ESI before we can > start talking with them. Please write your suggestions. > When we will know what we need from ESI we can start working on the > drivers. I will be glad to be able to test your work. > > -- > Regards, > Piotr Makowski > _______________________________________________ > Alsa-devel mailing list > Alsa-devel(a)alsa-project.org > http://mailman.alsa-project.org/mailman/listinfo/alsa-devel > -- We've Got Your Name at http://www.mail.com ! Get a FREE E-mail Account Today - Choose From 100+ Domains

1 0

[alsa-devel] Alsa-HOWTO
by Wallace, Brooke 21 Aug '07

21 Aug '07

Anyone know what happend to this howto? Seems like it had some good information that I can no longer find on the Offical ALSA Wiki... The URL was: http://www.alsa-project.org/alsa-doc/alsa-howto/c1706.htm <http://www.alsa-project.org/alsa-doc/alsa-howto/c1706.htm> before the switch to the new wiki was completed. -Brooke

2 1

[alsa-devel] Getting a driver to work
by Adrian McMenamin 20 Aug '07

20 Aug '07

Apologies for asking this old chestnut ... but I have upgraded my busybox/buildroot setup on my Dreamcast and now the AICA driver fails - looks pretty much like a failure to load the firmware. Information on the internet seems rather mixed up and out of date - some of it referring to 2.2 kernels etc... What is needed to load firmware - is it udev or hotplug (or is hotplug obsolete), and what role do the alsa libs have in all this? I went through all this two years ago but have forgotten again :( Thanks Adrian

2 2

[alsa-devel] VIA82XX on MSI K78MM Front Channel Problem
by Daniel Persch 20 Aug '07

20 Aug '07

Dear Developers, I'm using the on-board AC97 in 6-channel mode with analog output. However everything works fine except front channels: - front right is playing front left - front left is mute In stereo mode: - front right is playing front left - center is playing front right I was wandering whether someone could tell me where in the source I can play with the channel-settings/slots or if there is a solution for my issue. Or should I create a Bug-Report? Regards in advance, Daniel lspci output for the sound card: 00:11.5 0401: 1106:3059 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60) Alsamodule: via82xx

2 2

[alsa-devel] [PATCH] dbri: driver cleanup
by Krzysztof Helt 20 Aug '07

20 Aug '07

From: Krzysztof Helt <krzysztof.h1(a)wp.pl> This patch fixes white spaces, spelling and formatting to conform closer to the coding standard of the kernel. It contains few fixes pointed out by the checkpatch.pl script. Signed-off-by: Krzysztof Helt <krzysztof.h1(a)wp.pl> --- In case this email is mangled, the original patch is attached. diff -urp linux-2.6.23.2/sound/sparc/dbri.c linux-2.6. 23/sound/sparc/dbri.c --- linux-2.6.23.2/sound/sparc/dbri.c 2007-07-09 01:32:16. 000000000 +0200 +++ linux-2.6.23/sound/sparc/dbri.c 2007-08-17 10:48:31. 000000000 +0200 @@ -8,18 +8,18 @@ * Copyright (C) 1997 Rudolf Koenig (rfkoenig(a)immd4.informatik. uni-erlangen.de) * Copyright (C) 1998, 1999 Brent Baccala (baccala(a)freesoft.org) * - * This is the lowlevel driver for the DBRI & MMCODEC duo used for ISDN & AUDIO - * on Sun SPARCstation 10, 20, LX and Voyager models. + * This is the low level driver for the DBRI & MMCODEC duo used for ISDN & AUDIO + * on Sun SPARCStation 10, 20, LX and Voyager models. * * - DBRI: AT&T T5900FX Dual Basic Rates ISDN Interface. It is a 32 channel * data time multiplexer with ISDN support (aka T7259) * Interfaces: SBus,ISDN NT & TE, CHI, 4 bits parallel. * CHI: (spelled ki) Concentration Highway Interface (AT&T or Intel bus ?). * Documentation: - * - "STP 4000SBus Dual Basic Rate ISDN (DBRI) Tranceiver" from + * - "STP 4000SBus Dual Basic Rate ISDN (DBRI) Transceiver" from * Sparc Technology Business (courtesy of Sun Support) * - Data sheet of the T7903, a newer but very similar ISA bus equivalent - * available from the Lucent (formarly AT&T microelectronics) home + * available from the Lucent (formerly AT&T microelectronics) home * page. * - http://www.freesoft.org/Linux/DBRI/ * - MMCODEC: Crystal Semiconductor CS4215 16 bit Multimedia Audio Codec @@ -27,21 +27,21 @@ * Documentation: from the Crystal Semiconductor home page. * * The DBRI is a 32 pipe machine, each pipe can transfer some bits between - * memory and a serial device (long pipes, nr 0-15) or between two serial - * devices (short pipes, nr 16-31), or simply send a fixed data to a serial + * memory and a serial device (long pipes, no. 0-15) or between two serial + * devices (short pipes, no. 16-31), or simply send a fixed data to a serial * device (short pipes). - * A timeslot defines the bit-offset and nr of bits read from a serial device. + * A timeslot defines the bit-offset and no. of bits read from a serial device. * The timeslots are linked to 6 circular lists, one for each direction for * each serial device (NT,TE,CHI). A timeslot is associated to 1 or 2 pipes * (the second one is a monitor/tee pipe, valid only for serial input). * * The mmcodec is connected via the CHI bus and needs the data & some - * parameters (volume, output selection) timemultiplexed in 8 byte + * parameters (volume, output selection) time multiplexed in 8 byte * chunks. It also has a control mode, which serves for audio format setting. * * Looking at the CS4215 data sheet it is easy to set up 2 or 4 codecs on - * the same CHI bus, so I thought perhaps it is possible to use the onboard - * & the speakerbox codec simultanously, giving 2 (not very independent :-) + * the same CHI bus, so I thought perhaps it is possible to use the on-board + * & the speakerbox codec simultaneously, giving 2 (not very independent :-) * audio devices. But the SUN HW group decided against it, at least on my * LX the speakerbox connector has at least 1 pin missing and 1 wrongly * connected. @@ -56,6 +56,8 @@ #include <sound/driver.h> #include <linux/interrupt.h> #include <linux/delay.h> +#include <linux/irq.h> +#include <linux/io.h> #include <sound/core.h> #include <sound/pcm.h> @@ -64,8 +66,6 @@ #include <sound/control.h> #include <sound/initval.h> -#include <asm/irq.h> -#include <asm/io.h> #include <asm/sbus.h> #include <asm/atomic.h> @@ -76,7 +76,8 @@ MODULE_SUPPORTED_DEVICE("{{Sun,DBRI}}"); static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX; /* Index 0-MAX */ static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR; /* ID for this card */ -static int enable[SNDRV_CARDS] = SNDRV_DEFAULT_ENABLE_PNP; /* Enable this card */ +/* Enable this card */ +static int enable[SNDRV_CARDS] = SNDRV_DEFAULT_ENABLE_PNP; module_param_array(index, int, NULL, 0444); MODULE_PARM_DESC(index, "Index value for Sun DBRI soundcard."); @@ -104,7 +105,7 @@ static char *cmds[] = { "SSP", "CHI", "NT", "TE", "CDEC", "TEST", "CDM", "RESRV" }; -#define dprintk(a, x...) if(dbri_debug & a) printk(KERN_DEBUG x) +#define dprintk(a, x...) if (dbri_debug & a) printk(KERN_DEBUG x) #else #define dprintk(a, x...) do { } while (0) @@ -131,7 +132,7 @@ struct cs4215 { }; /* - * Control mode first + * Control mode first */ /* Time Slot 1, Status register */ @@ -219,7 +220,7 @@ static struct { /* Time Slot 7, Input Setting */ #define CS4215_LG(v) v /* Left Gain Setting 0xf: 22.5 dB */ #define CS4215_IS (1<<4) /* Input Select: 1=Microphone, 0=Line */ -#define CS4215_OVR (1<<5) /* 1: Overrange condition occurred */ +#define CS4215_OVR (1<<5) /* 1: Over range condition occurred */ #define CS4215_PIO0 (1<<6) /* Parallel I/O 0 */ #define CS4215_PIO1 (1<<7) @@ -285,7 +286,7 @@ struct dbri_pipe { /* Per stream (playback or record) information */ struct dbri_streaminfo { struct snd_pcm_substream *substream; - u32 dvma_buffer; /* Device view of Alsa DMA buffer */ + u32 dvma_buffer; /* Device view of ALSA DMA buffer */ int size; /* Size of DMA buffer */ size_t offset; /* offset in user buffer */ int pipe; /* Data pipe used */ @@ -341,11 +342,11 @@ struct snd_dbri { /* DBRI Reg1 - Mode and Interrupt Register - defines. (Page 18) */ #define D_LITTLE_END (1<<8) /* Byte Order */ #define D_BIG_END (0<<8) /* Byte Order */ -#define D_MRR (1<<4) /* Multiple Error Ack on SBus (readonly) */ -#define D_MLE (1<<3) /* Multiple Late Error on SBus (readonly) */ -#define D_LBG (1<<2) /* Lost Bus Grant on SBus (readonly) */ -#define D_MBE (1<<1) /* Burst Error on SBus (readonly) */ -#define D_IR (1<<0) /* Interrupt Indicator (readonly) */ +#define D_MRR (1<<4) /* Multiple Error Ack on SBus (read only) */ +#define D_MLE (1<<3) /* Multiple Late Error on SBus (read only) */ +#define D_LBG (1<<2) /* Lost Bus Grant on SBus (read only) */ +#define D_MBE (1<<1) /* Burst Error on SBus (read only) */ +#define D_IR (1<<0) /* Interrupt Indicator (read only) */ /* DBRI Reg2 - Parallel IO Register - defines. (Page 18) */ #define D_ENPIO3 (1<<7) /* Enable Pin 3 */ @@ -376,11 +377,11 @@ struct snd_dbri { #define D_CDM 0xe /* CHI Data mode command */ /* Special bits for some commands */ -#define D_PIPE(v) ((v)<<0) /* Pipe Nr: 0-15 long, 16-21 short */ +#define D_PIPE(v) ((v)<<0) /* Pipe No.: 0-15 long, 16-21 short */ /* Setup Data Pipe */ /* IRM */ -#define D_SDP_2SAME (1<<18) /* Report 2nd time in a row value rcvd */ +#define D_SDP_2SAME (1<<18) /* Report 2nd time in a row value received */ #define D_SDP_CHANGE (2<<18) /* Report any changes */ #define D_SDP_EVERY (3<<18) /* Report any changes */ #define D_SDP_EOL (1<<17) /* EOL interrupt enable */ @@ -419,7 +420,7 @@ struct snd_dbri { #define D_TS_NONCONTIG (3<<10) /* Non contiguous mode */ #define D_TS_ANCHOR (7<<10) /* Starting short pipes */ #define D_TS_MON(v) ((v)<<5) /* Monitor Pipe */ -#define D_TS_NEXT(v) ((v)<<0) /* Pipe Nr: 0-15 long, 16-21 short */ +#define D_TS_NEXT(v) ((v)<<0) /* Pipe no.: 0-15 long, 16-21 short */ /* Concentration Highway Interface Modes */ #define D_CHI_CHICM(v) ((v)<<16) /* Clock mode */ @@ -435,7 +436,7 @@ struct snd_dbri { #define D_NT_NBF (1<<16) /* Number of bad frames to loose framing */ #define D_NT_IRM_IMM (1<<15) /* Interrupt Report & Mask: Immediate */ #define D_NT_IRM_EN (1<<14) /* Interrupt Report & Mask: Enable */ -#define D_NT_ISNT (1<<13) /* Configfure interface as NT */ +#define D_NT_ISNT (1<<13) /* Configure interface as NT */ #define D_NT_FT (1<<12) /* Fixed Timing */ #define D_NT_EZ (1<<11) /* Echo Channel is Zeros */ #define D_NT_IFA (1<<10) /* Inhibit Final Activation */ @@ -455,7 +456,7 @@ struct snd_dbri { #define D_TEST_RAM(v) ((v)<<16) /* RAM Pointer */ #define D_TEST_SIZE(v) ((v)<<11) /* */ #define D_TEST_ROMONOFF 0x5 /* Toggle ROM opcode monitor on/off */ -#define D_TEST_PROC 0x6 /* MicroProcessor test */ +#define D_TEST_PROC 0x6 /* Microprocessor test */ #define D_TEST_SER 0x7 /* Serial-Controller test */ #define D_TEST_RAMREAD 0x8 /* Copy from Ram to system memory */ #define D_TEST_RAMWRITE 0x9 /* Copy into Ram from system memory */ @@ -464,12 +465,12 @@ struct snd_dbri { #define D_TEST_DUMP 0xe /* ROM Dump */ /* CHI Data Mode */ -#define D_CDM_THI (1<<8) /* Transmit Data on CHIDR Pin */ -#define D_CDM_RHI (1<<7) /* Receive Data on CHIDX Pin */ -#define D_CDM_RCE (1<<6) /* Receive on Rising Edge of CHICK */ -#define D_CDM_XCE (1<<2) /* Transmit Data on Rising Edge of CHICK */ -#define D_CDM_XEN (1<<1) /* Transmit Highway Enable */ -#define D_CDM_REN (1<<0) /* Receive Highway Enable */ +#define D_CDM_THI (1 << 8) /* Transmit Data on CHIDR Pin */ +#define D_CDM_RHI (1 << 7) /* Receive Data on CHIDX Pin */ +#define D_CDM_RCE (1 << 6) /* Receive on Rising Edge of CHICK */ +#define D_CDM_XCE (1 << 2) /* Transmit Data on Rising Edge of CHICK */ +#define D_CDM_XEN (1 << 1) /* Transmit Highway Enable */ +#define D_CDM_REN (1 << 0) /* Receive Highway Enable */ /* The Interrupts */ #define D_INTR_BRDY 1 /* Buffer Ready for processing */ @@ -493,9 +494,9 @@ struct snd_dbri { #define D_INTR_CHI 36 #define D_INTR_CMD 38 -#define D_INTR_GETCHAN(v) (((v)>>24) & 0x3f) -#define D_INTR_GETCODE(v) (((v)>>20) & 0xf) -#define D_INTR_GETCMD(v) (((v)>>16) & 0xf) +#define D_INTR_GETCHAN(v) (((v) >> 24) & 0x3f) +#define D_INTR_GETCODE(v) (((v) >> 20) & 0xf) +#define D_INTR_GETCMD(v) (((v) >> 16) & 0xf) #define D_INTR_GETVAL(v) ((v) & 0xffff) #define D_INTR_GETRVAL(v) ((v) & 0xfffff) @@ -533,41 +534,42 @@ struct snd_dbri { #define D_P_31 31 /* */ /* Transmit descriptor defines */ -#define DBRI_TD_F (1<<31) /* End of Frame */ -#define DBRI_TD_D (1<<30) /* Do not append CRC */ -#define DBRI_TD_CNT(v) ((v)<<16) /* Number of valid bytes in the buffer */ -#define DBRI_TD_B (1<<15) /* Final interrupt */ -#define DBRI_TD_M (1<<14) /* Marker interrupt */ -#define DBRI_TD_I (1<<13) /* Transmit Idle Characters */ -#define DBRI_TD_FCNT(v) (v) /* Flag Count */ -#define DBRI_TD_UNR (1<<3) /* Underrun: transmitter is out of data */ -#define DBRI_TD_ABT (1<<2) /* Abort: frame aborted */ -#define DBRI_TD_TBC (1<<0) /* Transmit buffer Complete */ -#define DBRI_TD_STATUS(v) ((v)&0xff) /* Transmit status */ - /* Maximum buffer size per TD: almost 8Kb */ +#define DBRI_TD_F (1 << 31) /* End of Frame */ +#define DBRI_TD_D (1 << 30) /* Do not append CRC */ +#define DBRI_TD_CNT(v) ((v) << 16) /* Number of valid bytes in the buffer */ +#define DBRI_TD_B (1 << 15) /* Final interrupt */ +#define DBRI_TD_M (1 << 14) /* Marker interrupt */ +#define DBRI_TD_I (1 << 13) /* Transmit Idle Characters */ +#define DBRI_TD_FCNT(v) (v) /* Flag Count */ +#define DBRI_TD_UNR (1 << 3) /* Underrun: transmitter is out of data */ +#define DBRI_TD_ABT (1 << 2) /* Abort: frame aborted */ +#define DBRI_TD_TBC (1 << 0) /* Transmit buffer Complete */ +#define DBRI_TD_STATUS(v) ((v) & 0xff) /* Transmit status */ + /* Maximum buffer size per TD: almost 8KB */ #define DBRI_TD_MAXCNT ((1 << 13) - 4) /* Receive descriptor defines */ -#define DBRI_RD_F (1<<31) /* End of Frame */ -#define DBRI_RD_C (1<<30) /* Completed buffer */ -#define DBRI_RD_B (1<<15) /* Final interrupt */ -#define DBRI_RD_M (1<<14) /* Marker interrupt */ -#define DBRI_RD_BCNT(v) (v) /* Buffer size */ -#define DBRI_RD_CRC (1<<7) /* 0: CRC is correct */ -#define DBRI_RD_BBC (1<<6) /* 1: Bad Byte received */ -#define DBRI_RD_ABT (1<<5) /* Abort: frame aborted */ -#define DBRI_RD_OVRN (1<<3) /* Overrun: data lost */ -#define DBRI_RD_STATUS(v) ((v)&0xff) /* Receive status */ -#define DBRI_RD_CNT(v) (((v)>>16)&0x1fff) /* Valid bytes in the buffer */ +#define DBRI_RD_F (1 << 31) /* End of Frame */ +#define DBRI_RD_C (1 << 30) /* Completed buffer */ +#define DBRI_RD_B (1 << 15) /* Final interrupt */ +#define DBRI_RD_M (1 << 14) /* Marker interrupt */ +#define DBRI_RD_BCNT(v) (v) /* Buffer size */ +#define DBRI_RD_CRC (1 << 7) /* 0: CRC is correct */ +#define DBRI_RD_BBC (1 << 6) /* 1: Bad Byte received */ +#define DBRI_RD_ABT (1 << 5) /* Abort: frame aborted */ +#define DBRI_RD_OVRN (1 << 3) /* Overrun: data lost */ +#define DBRI_RD_STATUS(v) ((v) & 0xff) /* Receive status */ +#define DBRI_RD_CNT(v) (((v) >> 16) & 0x1fff) /* Valid bytes in the buffer */ /* stream_info[] access */ /* Translate the ALSA direction into the array index */ #define DBRI_STREAMNO(substream) \ - (substream->stream == \ + (substream->stream == \ SNDRV_PCM_STREAM_PLAYBACK? DBRI_PLAY: DBRI_REC) /* Return a pointer to dbri_streaminfo */ -#define DBRI_STREAM(dbri, substream) &dbri->stream_info[DBRI_STREAMNO(substream)] +#define DBRI_STREAM(dbri, substream) \ + &dbri->stream_info[DBRI_STREAMNO(substream)] static struct snd_dbri *dbri_list; /* All DBRI devices */ @@ -612,18 +614,18 @@ Since the DBRI can run in parallel with synchronization present themselves. The method implemented here is only use of the dbri_cmdwait() to wait for execution of batch of sent commands. -A circular command buffer is used here. A new command is being added +A circular command buffer is used here. A new command is being added while another can be executed. The scheme works by adding two WAIT commands after each sent batch of commands. When the next batch is prepared it is added after the WAIT commands then the WAITs are replaced with single JUMP -command to the new batch. The the DBRI is forced to reread the last WAIT -command (replaced by the JUMP by then). If the DBRI is still executing +command to the new batch. The the DBRI is forced to reread the last WAIT +command (replaced by the JUMP by then). If the DBRI is still executing previous commands the request to reread the WAIT command is ignored. Every time a routine wants to write commands to the DBRI, it must -first call dbri_cmdlock() and get pointer to a free space in -dbri->dma->cmd buffer. After this, the commands can be written to -the buffer, and dbri_cmdsend() is called with the final pointer value +first call dbri_cmdlock() and get pointer to a free space in +dbri->dma->cmd buffer. After this, the commands can be written to +the buffer, and dbri_cmdsend() is called with the final pointer value to send them to the DBRI. */ @@ -657,7 +659,7 @@ static void dbri_cmdwait(struct snd_dbri * Lock the command queue and returns pointer to a space for len cmd words * It locks the cmdlock spinlock. */ -static s32 *dbri_cmdlock(struct snd_dbri * dbri, int len) +static s32 *dbri_cmdlock(struct snd_dbri *dbri, int len) { /* Space for 2 WAIT cmds (replaced later by 1 JUMP cmd) */ len += 2; @@ -680,7 +682,7 @@ static s32 *dbri_cmdlock(struct snd_dbri * * Lock must be held before calling this. */ -static void dbri_cmdsend(struct snd_dbri * dbri, s32 * cmd,int len) +static void dbri_cmdsend(struct snd_dbri *dbri, s32 *cmd, int len) { s32 tmp, addr; static int wait_id = 0; @@ -700,16 +702,17 @@ static void dbri_cmdsend(struct snd_dbri s32 *ptr; for (ptr = dbri->cmdptr; ptr < cmd+2; ptr++) - dprintk(D_CMD, "cmd: %lx:%08x\n", (unsigned long)ptr, *ptr); + dprintk(D_CMD, "cmd: %lx:%08x\n", + (unsigned long)ptr, *ptr); } else { s32 *ptr = dbri->cmdptr; dprintk(D_CMD, "cmd: %lx:%08x\n", (unsigned long)ptr, *ptr); ptr++; dprintk(D_CMD, "cmd: %lx:%08x\n", (unsigned long)ptr, *ptr); - for (ptr = dbri->dma->cmd; ptr < cmd+2; ptr++) { - dprintk(D_CMD, "cmd: %lx:%08x\n", (unsigned long)ptr, *ptr); - } + for (ptr = dbri->dma->cmd; ptr < cmd+2; ptr++) + dprintk(D_CMD, "cmd: %lx:%08x\n", + (unsigned long)ptr, *ptr); } #endif @@ -723,7 +726,7 @@ static void dbri_cmdsend(struct snd_dbri } /* Lock must be held when calling this */ -static void dbri_reset(struct snd_dbri * dbri) +static void dbri_reset(struct snd_dbri *dbri) { int i; u32 tmp; @@ -746,7 +749,7 @@ static void dbri_reset(struct snd_dbri * } /* Lock must not be held before calling this */ -static void dbri_initialize(struct snd_dbri * dbri) +static void dbri_initialize(struct snd_dbri *dbri) { s32 *cmd; u32 dma_addr; @@ -763,7 +766,7 @@ static void dbri_initialize(struct snd_d spin_lock_init(&dbri->cmdlock); /* - * Initialize the interrupt ringbuffer. + * Initialize the interrupt ring buffer. */ dma_addr = dbri->dma_dvma + dbri_dma_off(intr, 0); dbri->dma->intr[0] = dma_addr; @@ -801,7 +804,7 @@ list ordering, among other things. The here interface closely with the transmit and receive interrupt code. */ -static int pipe_active(struct snd_dbri * dbri, int pipe) +static int pipe_active(struct snd_dbri *dbri, int pipe) { return ((pipe >= 0) && (dbri->pipes[pipe].desc != -1)); } @@ -811,20 +814,22 @@ static int pipe_active(struct snd_dbri * * Called on an in-use pipe to clear anything being transmitted or received * Lock must be held before calling this. */ -static void reset_pipe(struct snd_dbri * dbri, int pipe) +static void reset_pipe(struct snd_dbri *dbri, int pipe) { int sdp; int desc; s32 *cmd; if (pipe < 0 || pipe > DBRI_MAX_PIPE) { - printk(KERN_ERR "DBRI: reset_pipe called with illegal pipe number\n"); + printk(KERN_ERR "DBRI: reset_pipe called with " + "illegal pipe number\n"); return; } sdp = dbri->pipes[pipe].sdp; if (sdp == 0) { - printk(KERN_ERR "DBRI: reset_pipe called on uninitialized pipe\n"); + printk(KERN_ERR "DBRI: reset_pipe called " + "on uninitialized pipe\n"); return; } @@ -835,9 +840,10 @@ static void reset_pipe(struct snd_dbri * dbri_cmdsend(dbri, cmd, 3); desc = dbri->pipes[pipe].first_desc; - if ( desc >= 0) + if (desc >= 0) do { - dbri->dma->desc[desc].nda = dbri->dma->desc[desc].ba = 0; + dbri->dma->desc[desc].ba = 0; + dbri->dma->desc[desc].nda = 0; desc = dbri->next_desc[desc]; } while (desc != -1 && desc != dbri->pipes[pipe]. first_desc); @@ -848,15 +854,17 @@ static void reset_pipe(struct snd_dbri * /* * Lock must be held before calling this. */ -static void setup_pipe(struct snd_dbri * dbri, int pipe, int sdp) +static void setup_pipe(struct snd_dbri *dbri, int pipe, int sdp) { if (pipe < 0 || pipe > DBRI_MAX_PIPE) { - printk(KERN_ERR "DBRI: setup_pipe called with illegal pipe number\n"); + printk(KERN_ERR "DBRI: setup_pipe called " + "with illegal pipe number\n"); return; } if ((sdp & 0xf800) != sdp) { - printk(KERN_ERR "DBRI: setup_pipe called with strange SDP value\n"); + printk(KERN_ERR "DBRI: setup_pipe called " + "with strange SDP value\n"); /* sdp &= 0xf800; */ } @@ -877,25 +885,26 @@ static void setup_pipe(struct snd_dbri * /* * Lock must be held before calling this. */ -static void link_time_slot(struct snd_dbri * dbri, int pipe, +static void link_time_slot(struct snd_dbri *dbri, int pipe, int prevpipe, int nextpipe, int length, int cycle) { s32 *cmd; int val; - if (pipe < 0 || pipe > DBRI_MAX_PIPE + if (pipe < 0 || pipe > DBRI_MAX_PIPE || prevpipe < 0 || prevpipe > DBRI_MAX_PIPE || nextpipe < 0 || nextpipe > DBRI_MAX_PIPE) { - printk(KERN_ERR + printk(KERN_ERR "DBRI: link_time_slot called with illegal pipe number\n"); return; } - if (dbri->pipes[pipe].sdp == 0 + if (dbri->pipes[pipe].sdp == 0 || dbri->pipes[prevpipe].sdp == 0 || dbri->pipes[nextpipe].sdp == 0) { - printk(KERN_ERR "DBRI: link_time_slot called on uninitialized pipe\n"); + printk(KERN_ERR "DBRI: link_time_slot called " + "on uninitialized pipe\n"); return; } @@ -935,17 +944,17 @@ static void link_time_slot(struct snd_db /* * Lock must be held before calling this. */ -static void unlink_time_slot(struct snd_dbri * dbri, int pipe, +static void unlink_time_slot(struct snd_dbri *dbri, int pipe, enum in_or_out direction, int prevpipe, int nextpipe) { s32 *cmd; int val; - if (pipe < 0 || pipe > DBRI_MAX_PIPE + if (pipe < 0 || pipe > DBRI_MAX_PIPE || prevpipe < 0 || prevpipe > DBRI_MAX_PIPE || nextpipe < 0 || nextpipe > DBRI_MAX_PIPE) { - printk(KERN_ERR + printk(KERN_ERR "DBRI: unlink_time_slot called with illegal pipe number\n"); return; } @@ -985,7 +994,7 @@ static void unlink_time_slot(struct snd_ * * Lock must not be held before calling it. */ -static void xmit_fixed(struct snd_dbri * dbri, int pipe, unsigned int data) +static void xmit_fixed(struct snd_dbri *dbri, int pipe, unsigned int data) { s32 *cmd; unsigned long flags; @@ -996,7 +1005,8 @@ static void xmit_fixed(struct snd_dbri * } if (D_SDP_MODE(dbri->pipes[pipe].sdp) == 0) { - printk(KERN_ERR "DBRI: xmit_fixed: Uninitialized pipe % d\n", pipe); + printk(KERN_ERR "DBRI: xmit_fixed: " + "Uninitialized pipe %d\n", pipe); return; } @@ -1006,7 +1016,8 @@ static void xmit_fixed(struct snd_dbri * } if (!(dbri->pipes[pipe].sdp & D_SDP_TO_SER)) { - printk(KERN_ERR "DBRI: xmit_fixed: Called on receive pipe %d\n", pipe); + printk(KERN_ERR "DBRI: xmit_fixed: Called on receive pipe %d\n", + pipe); return; } @@ -1028,20 +1039,23 @@ static void xmit_fixed(struct snd_dbri * } -static void recv_fixed(struct snd_dbri * dbri, int pipe, volatile __u32 * ptr) +static void recv_fixed(struct snd_dbri *dbri, int pipe, volatile __u32 *ptr) { if (pipe < 16 || pipe > DBRI_MAX_PIPE) { - printk(KERN_ERR "DBRI: recv_fixed called with illegal pipe number\n"); + printk(KERN_ERR "DBRI: recv_fixed called with " + "illegal pipe number\n"); return; } if (D_SDP_MODE(dbri->pipes[pipe].sdp) != D_SDP_FIXED) { - printk(KERN_ERR "DBRI: recv_fixed called on non-fixed pipe %d\n", pipe); + printk(KERN_ERR "DBRI: recv_fixed called on " + "non-fixed pipe %d\n", pipe); return; } if (dbri->pipes[pipe].sdp & D_SDP_TO_SER) { - printk(KERN_ERR "DBRI: recv_fixed called on transmit pipe %d\n", pipe); + printk(KERN_ERR "DBRI: recv_fixed called on " + "transmit pipe %d\n", pipe); return; } @@ -1064,7 +1078,7 @@ static void recv_fixed(struct snd_dbri * * * Lock must be held before calling this. */ -static int setup_descs(struct snd_dbri * dbri, int streamno, unsigned int period) +static int setup_descs(struct snd_dbri *dbri, int streamno, unsigned int period) { struct dbri_streaminfo *info = &dbri->stream_info[streamno] ; __u32 dvma_buffer; @@ -1089,21 +1103,23 @@ static int setup_descs(struct snd_dbri * if (streamno == DBRI_PLAY) { if (!(dbri->pipes[info->pipe].sdp & D_SDP_TO_SER)) { - printk(KERN_ERR "DBRI: setup_descs: Called on receive pipe %d\n", - info->pipe); + printk(KERN_ERR "DBRI: setup_descs: " + "Called on receive pipe %d\n", info->pipe); return -2; } } else { if (dbri->pipes[info->pipe].sdp & D_SDP_TO_SER) { - printk(KERN_ERR + printk(KERN_ERR "DBRI: setup_descs: Called on transmit pipe %d\n", info->pipe); return -2; } - /* Should be able to queue multiple buffers to receive on a pipe */ + /* Should be able to queue multiple buffers + * to receive on a pipe + */ if (pipe_active(dbri, info->pipe)) { - printk(KERN_ERR "DBRI: recv_on_pipe: Called on active pipe %d\n", - info->pipe); + printk(KERN_ERR "DBRI: recv_on_pipe: " + "Called on active pipe %d\n", info->pipe); return -2; } @@ -1113,11 +1129,13 @@ static int setup_descs(struct snd_dbri * /* Free descriptors if pipe has any */ desc = dbri->pipes[info->pipe].first_desc; - if ( desc >= 0) + if (desc >= 0) do { - dbri->dma->desc[desc].nda = dbri->dma->desc[desc].ba = 0; + dbri->dma->desc[desc].ba = 0; + dbri->dma->desc[desc].nda = 0; desc = dbri->next_desc[desc]; - } while (desc != -1 && desc != dbri->pipes[info->pipe]. first_desc); + } while (desc != -1 && + desc != dbri->pipes[info->pipe].first_desc); dbri->pipes[info->pipe].desc = -1; dbri->pipes[info->pipe].first_desc = -1; @@ -1150,8 +1168,7 @@ static int setup_descs(struct snd_dbri * if (streamno == DBRI_PLAY) { dbri->dma->desc[desc].word1 = DBRI_TD_CNT(mylen); dbri->dma->desc[desc].word4 = 0; - dbri->dma->desc[desc].word1 |= - DBRI_TD_F | DBRI_TD_B; + dbri->dma->desc[desc].word1 |= DBRI_TD_F | DBRI_TD_B; } else { dbri->dma->desc[desc].word1 = 0; dbri->dma->desc[desc].word4 = @@ -1172,7 +1189,8 @@ static int setup_descs(struct snd_dbri * } if (first_desc == -1 || last_desc == -1) { - printk(KERN_ERR "DBRI: setup_descs: Not enough descriptors available\n"); + printk(KERN_ERR "DBRI: setup_descs: " + " Not enough descriptors available\n"); return -1; } @@ -1183,14 +1201,14 @@ static int setup_descs(struct snd_dbri * dbri->pipes[info->pipe].desc = first_desc; #ifdef DBRI_DEBUG - for (desc = first_desc; desc != -1; ) { + for (desc = first_desc; desc != -1;) { dprintk(D_DESC, "DESC %d: %08x %08x %08x %08x\n", desc, dbri->dma->desc[desc].word1, dbri->dma->desc[desc].ba, dbri->dma->desc[desc].nda, dbri->dma->desc[desc]. word4); desc = dbri->next_desc[desc]; - if ( desc == first_desc ) + if (desc == first_desc) break; } #endif @@ -1213,7 +1231,8 @@ enum master_or_slave { CHImaster, CHIsla /* * Lock must not be held before calling it. */ -static void reset_chi(struct snd_dbri * dbri, enum master_or_slave master_or_slave, +static void reset_chi(struct snd_dbri *dbri, + enum master_or_slave master_or_slave, int bits_per_frame) { s32 *cmd; @@ -1222,7 +1241,7 @@ static void reset_chi(struct snd_dbri * /* Set CHI Anchor: Pipe 16 */ cmd = dbri_cmdlock(dbri, 4); - val = D_DTS_VO | D_DTS_VI | D_DTS_INS + val = D_DTS_VO | D_DTS_VI | D_DTS_INS | D_DTS_PRVIN(16) | D_PIPE(16) | D_DTS_PRVOUT(16); *(cmd++) = DBRI_CMD(D_DTS, 0, val); *(cmd++) = D_TS_ANCHOR | D_TS_NEXT(16); @@ -1246,15 +1265,16 @@ static void reset_chi(struct snd_dbri * } else { /* Setup DBRI for CHI Master - generate clock, FS * - * BPF = bits per 8 kHz frame - * 12.288 MHz / CHICM_divisor = clock rate - * FD = 1 - drive CHIFS on rising edge of CHICK + * BPF = bits per 8 kHz frame + * 12.288 MHz / CHICM_divisor = clock rate + * FD = 1 - drive CHIFS on rising edge of CHICK */ int clockrate = bits_per_frame * 8; int divisor = 12288 / clockrate; if (divisor > 255 || divisor * clockrate != 12288) - printk(KERN_ERR "DBRI: illegal bits_per_frame in setup_chi\n"); + printk(KERN_ERR "DBRI: illegal bits_per_frame " + "in setup_chi\n"); *(cmd++) = DBRI_CMD(D_CHI, 0, D_CHI_CHICM(divisor) | D_CHI_FD | D_CHI_BPF(bits_per_frame)); @@ -1288,7 +1308,7 @@ to the DBRI via the CHI interface and fe * Lock must not be held before calling it. */ -static void cs4215_setup_pipes(struct snd_dbri * dbri) +static void cs4215_setup_pipes(struct snd_dbri *dbri) { unsigned long flags; @@ -1303,9 +1323,9 @@ static void cs4215_setup_pipes(struct sn * not relevant for us (only for doublechecking). * * Control mode: - * Pipe 17: Send timeslots 1-4 (slots 5-8 are readonly) + * Pipe 17: Send timeslots 1-4 (slots 5-8 are read only) * Pipe 18: Receive timeslot 1 (clb). - * Pipe 19: Receive timeslot 7 (version). + * Pipe 19: Receive timeslot 7 (version). */ setup_pipe(dbri, 4, D_SDP_MEM | D_SDP_TO_SER | D_SDP_MSB); @@ -1355,7 +1375,7 @@ static int cs4215_init_data(struct cs421 return 0; } -static void cs4215_setdata(struct snd_dbri * dbri, int muted) +static void cs4215_setdata(struct snd_dbri *dbri, int muted) { if (muted) { dbri->mm.data[0] |= 63; @@ -1387,7 +1407,7 @@ static void cs4215_setdata(struct snd_db /* * Set the CS4215 to data mode. */ -static void cs4215_open(struct snd_dbri * dbri) +static void cs4215_open(struct snd_dbri *dbri) { int data_width; u32 tmp; @@ -1452,7 +1472,7 @@ static void cs4215_open(struct snd_dbri /* * Send the control information (i.e. audio format) */ -static int cs4215_setctrl(struct snd_dbri * dbri) +static int cs4215_setctrl(struct snd_dbri *dbri) { int i, val; u32 tmp; @@ -1502,9 +1522,9 @@ static int cs4215_setctrl(struct snd_dbr /* * Control mode: - * Pipe 17: Send timeslots 1-4 (slots 5-8 are readonly) + * Pipe 17: Send timeslots 1-4 (slots 5-8 are read only) * Pipe 18: Receive timeslot 1 (clb). - * Pipe 19: Receive timeslot 7 (version). + * Pipe 19: Receive timeslot 7 (version). */ link_time_slot(dbri, 17, 16, 16, 32, dbri->mm.offset); @@ -1522,9 +1542,9 @@ static int cs4215_setctrl(struct snd_dbr sbus_writel(tmp, dbri->regs + REG0); spin_unlock_irqrestore(&dbri->lock, flags); - for (i = 10; ((dbri->mm.status & 0xe4) != 0x20); --i) { + for (i = 10; ((dbri->mm.status & 0xe4) != 0x20); --i) msleep_interruptible(1); - } + if (i == 0) { dprintk(D_MM, "CS4215 didn't respond to CLB (0x%02x)\n", dbri->mm.status); @@ -1556,7 +1576,7 @@ static int cs4215_setctrl(struct snd_dbr * As part of the process we resend the settings for the data * timeslots as well. */ -static int cs4215_prepare(struct snd_dbri * dbri, unsigned int rate, +static int cs4215_prepare(struct snd_dbri *dbri, unsigned int rate, snd_pcm_format_t format, unsigned int channels) { int freq_idx; @@ -1613,7 +1633,7 @@ static int cs4215_prepare(struct snd_dbr /* * */ -static int cs4215_init(struct snd_dbri * dbri) +static int cs4215_init(struct snd_dbri *dbri) { u32 reg2 = sbus_readl(dbri->regs + REG2); dprintk(D_MM, "cs4215_init: reg2=0x%x\n", reg2); @@ -1674,7 +1694,7 @@ interrupts are disabled. /* xmit_descs() * - * Starts transmiting the current TD's for recording/playing. + * Starts transmitting the current TD's for recording/playing. * For playback, ALSA has filled the DMA memory with new data (we hope). */ static void xmit_descs(struct snd_dbri *dbri) @@ -1701,7 +1721,8 @@ static void xmit_descs(struct snd_dbri * *(cmd++) = DBRI_CMD(D_SDP, 0, dbri->pipes[info->pipe].sdp | D_SDP_P | D_SDP_EVERY | D_SDP_C); - *(cmd++) = dbri->dma_dvma + dbri_dma_off(desc, first_td); + *(cmd++) = dbri->dma_dvma + + dbri_dma_off(desc, first_td); dbri_cmdsend(dbri, cmd, 2); /* Reset our admin of the pipe. */ @@ -1722,7 +1743,8 @@ static void xmit_descs(struct snd_dbri * *(cmd++) = DBRI_CMD(D_SDP, 0, dbri->pipes[info->pipe].sdp | D_SDP_P | D_SDP_EVERY | D_SDP_C); - *(cmd++) = dbri->dma_dvma + dbri_dma_off(desc, first_td); + *(cmd++) = dbri->dma_dvma + + dbri_dma_off(desc, first_td); dbri_cmdsend(dbri, cmd, 2); /* Reset our admin of the pipe. */ @@ -1747,7 +1769,7 @@ static void xmit_descs(struct snd_dbri * * */ -static void transmission_complete_intr(struct snd_dbri * dbri, int pipe) +static void transmission_complete_intr(struct snd_dbri *dbri, int pipe) { struct dbri_streaminfo *info; int td; @@ -1763,9 +1785,8 @@ static void transmission_complete_intr(s } status = DBRI_TD_STATUS(dbri->dma->desc[td].word4); - if (!(status & DBRI_TD_TBC)) { + if (!(status & DBRI_TD_TBC)) break; - } dprintk(D_INT, "TD %d, status 0x%02x\n", td, status); @@ -1785,7 +1806,7 @@ static void transmission_complete_intr(s snd_pcm_period_elapsed(info->substream); } -static void reception_complete_intr(struct snd_dbri * dbri, int pipe) +static void reception_complete_intr(struct snd_dbri *dbri, int pipe) { struct dbri_streaminfo *info; int rd = dbri->pipes[pipe].desc; @@ -1817,7 +1838,7 @@ static void reception_complete_intr(stru snd_pcm_period_elapsed(info->substream); } -static void dbri_process_one_interrupt(struct snd_dbri * dbri, int x) +static void dbri_process_one_interrupt(struct snd_dbri *dbri, int x) { int val = D_INTR_GETVAL(x); int channel = D_INTR_GETCHAN(x); @@ -1889,7 +1910,7 @@ static void dbri_process_one_interrupt(s * right now). Non-zero words require processing and are handed off * to dbri_process_one_interrupt AFTER advancing the pointer. */ -static void dbri_process_interrupt_buffer(struct snd_dbri * dbri) +static void dbri_process_interrupt_buffer(struct snd_dbri *dbri) { s32 x; @@ -1965,15 +1986,15 @@ static irqreturn_t snd_dbri_interrupt(in PCM Interface ***************************************************************** ***********/ static struct snd_pcm_hardware snd_dbri_pcm_hw = { - .info = (SNDRV_PCM_INFO_MMAP | - SNDRV_PCM_INFO_INTERLEAVED | - SNDRV_PCM_INFO_BLOCK_TRANSFER | - SNDRV_PCM_INFO_MMAP_VALID), - .formats = SNDRV_PCM_FMTBIT_MU_LAW | - SNDRV_PCM_FMTBIT_A_LAW | - SNDRV_PCM_FMTBIT_U8 | - SNDRV_PCM_FMTBIT_S16_BE, - .rates = SNDRV_PCM_RATE_8000_48000 | SNDRV_PCM_RATE_5512, + .info = (SNDRV_PCM_INFO_MMAP | + SNDRV_PCM_INFO_INTERLEAVED | + SNDRV_PCM_INFO_BLOCK_TRANSFER | + SNDRV_PCM_INFO_MMAP_VALID), + .formats = SNDRV_PCM_FMTBIT_MU_LAW | + SNDRV_PCM_FMTBIT_A_LAW | + SNDRV_PCM_FMTBIT_U8 | + SNDRV_PCM_FMTBIT_S16_BE, + .rates = SNDRV_PCM_RATE_8000_48000 | SNDRV_PCM_RATE_5512, .rate_min = 5512, .rate_max = 48000, .channels_min = 1, @@ -2011,7 +2032,8 @@ static int snd_hw_rule_channels(struct s snd_interval_any(&ch); if (!(f->bits[0] & SNDRV_PCM_FMTBIT_S16_BE)) { - ch.min = ch.max = 1; + ch.min = 1; + ch.max = 1; ch.integer = 1; return snd_interval_refine(c, &ch); } @@ -2035,14 +2057,14 @@ static int snd_dbri_open(struct snd_pcm_ info->pipe = -1; spin_unlock_irqrestore(&dbri->lock, flags); - snd_pcm_hw_rule_add(runtime,0,SNDRV_PCM_HW_PARAM_CHANNELS, + snd_pcm_hw_rule_add(runtime, 0, SNDRV_PCM_HW_PARAM_CHANNELS, snd_hw_rule_format, NULL, SNDRV_PCM_HW_PARAM_FORMAT, -1); - snd_pcm_hw_rule_add(runtime,0,SNDRV_PCM_HW_PARAM_FORMAT, - snd_hw_rule_channels, NULL, + snd_pcm_hw_rule_add(runtime, 0, SNDRV_PCM_HW_PARAM_FORMAT, + snd_hw_rule_channels, NULL, SNDRV_PCM_HW_PARAM_CHANNELS, -1); - + cs4215_open(dbri); return 0; @@ -2145,7 +2167,7 @@ static int snd_dbri_prepare(struct snd_p spin_lock_irq(&dbri->lock); info->offset = 0; - /* Setup the all the transmit/receive desciptors to cover the + /* Setup the all the transmit/receive descriptors to cover the * whole DMA buffer. */ ret = setup_descs(dbri, DBRI_STREAMNO(substream), @@ -2205,7 +2227,7 @@ static struct snd_pcm_ops snd_dbri_ops = .pointer = snd_dbri_pointer, }; -static int __devinit snd_dbri_pcm(struct snd_dbri * dbri) +static int __devinit snd_dbri_pcm(struct snd_dbri *dbri) { struct snd_pcm *pcm; int err; @@ -2228,9 +2250,8 @@ static int __devinit snd_dbri_pcm(struct if ((err = snd_pcm_lib_preallocate_pages_for_all(pcm, SNDRV_DMA_TYPE_CONTINUOUS, snd_dma_continuous_data(GFP_KERNEL), - 64 * 1024, 64 * 1024)) < 0) { + 64 * 1024, 64 * 1024)) < 0) return err; - } return 0; } @@ -2271,7 +2292,8 @@ static int snd_cs4215_put_volume(struct struct snd_ctl_elem_value *ucontrol) { struct snd_dbri *dbri = snd_kcontrol_chip(kcontrol); - struct dbri_streaminfo *info = &dbri->stream_info[kcontrol->private_value]; + struct dbri_streaminfo *info = + &dbri->stream_info[kcontrol->private_value]; int changed = 0; if (info->left_gain != ucontrol->value.integer.value[0]) { @@ -2316,18 +2338,16 @@ static int snd_cs4215_get_single(struct int invert = (kcontrol->private_value >> 24) & 1; snd_assert(dbri != NULL, return -EINVAL); - if (elem < 4) { + if (elem < 4) ucontrol->value.integer.value[0] = (dbri->mm.data[elem] >> shift) & mask; - } else { + else ucontrol->value.integer.value[0] = (dbri->mm.ctrl[elem - 4] >> shift) & mask; - } - if (invert == 1) { + if (invert == 1) ucontrol->value.integer.value[0] = mask - ucontrol->value.integer.value[0]; - } return 0; } @@ -2378,11 +2398,12 @@ static int snd_cs4215_put_single(struct timeslots. Shift is the bit offset in the timeslot, mask defines the number of bits. invert is a boolean for use with attenuation. */ -#define CS4215_SINGLE(xname, entry, shift, mask, invert) \ -{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = xname, \ - .info = snd_cs4215_info_single, \ - .get = snd_cs4215_get_single, .put = snd_cs4215_put_single, \ - .private_value = entry | (shift << 8) | (mask << 16) | (invert << 24) }, +#define CS4215_SINGLE(xname, entry, shift, mask, invert) \ +{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname), \ + .info = snd_cs4215_info_single, \ + .get = snd_cs4215_get_single, .put = snd_cs4215_put_single, \ + .private_value = (entry) | ((shift) << 8) | ((mask) << 16) | \ + ((invert) << 24) }, static struct snd_kcontrol_new dbri_controls[] __devinitdata = { { @@ -2411,7 +2432,7 @@ static struct snd_kcontrol_new dbri_cont CS4215_SINGLE("Mic boost", 4, 4, 1, 1) }; -static int __init snd_dbri_mixer(struct snd_dbri * dbri) +static int __init snd_dbri_mixer(struct snd_dbri *dbri) { struct snd_card *card; int idx, err; @@ -2438,7 +2459,8 @@ static int __init snd_dbri_mixer(struct /**************************************************************** ************ /proc interface ***************************************************************** ***********/ -static void dbri_regs_read(struct snd_info_entry * entry, struct snd_info_buffer *buffer) +static void dbri_regs_read(struct snd_info_entry *entry, + struct snd_info_buffer *buffer) { struct snd_dbri *dbri = entry->private_data; @@ -2449,7 +2471,7 @@ static void dbri_regs_read(struct snd_in } #ifdef DBRI_DEBUG -static void dbri_debug_read(struct snd_info_entry * entry, +static void dbri_debug_read(struct snd_info_entry *entry, struct snd_info_buffer *buffer) { struct snd_dbri *dbri = entry->private_data; @@ -2463,7 +2485,8 @@ static void dbri_debug_read(struct snd_i "Pipe %d: %s SDP=0x%x desc=%d, " "len=%d next %d\n", pipe, - ((pptr->sdp & D_SDP_TO_SER) ? "output" : "input") , + ((pptr->sdp & D_SDP_TO_SER) ? "output" : + "input"), pptr->sdp, pptr->desc, pptr->length, pptr->nextpipe); } @@ -2471,11 +2494,11 @@ static void dbri_debug_read(struct snd_i } #endif -void snd_dbri_proc(struct snd_dbri * dbri) +void snd_dbri_proc(struct snd_dbri *dbri) { struct snd_info_entry *entry; - if (! snd_card_proc_new(dbri->card, "regs", &entry)) + if (!snd_card_proc_new(dbri->card, "regs", &entry)) snd_info_set_text_ops(entry, dbri, dbri_regs_read); #ifdef DBRI_DEBUG @@ -2491,7 +2514,7 @@ void snd_dbri_proc(struct snd_dbri * dbr **************************** Initialization ******************************** ***************************************************************** *********** */ -static void snd_dbri_free(struct snd_dbri * dbri); +static void snd_dbri_free(struct snd_dbri *dbri); static int __init snd_dbri_create(struct snd_card *card, struct sbus_dev *sdev, @@ -2547,7 +2570,7 @@ static int __init snd_dbri_create(struct return 0; } -static void snd_dbri_free(struct snd_dbri * dbri) +static void snd_dbri_free(struct snd_dbri *dbri) { dprintk(D_GEN, "snd_dbri_free\n"); dbri_reset(dbri); @@ -2587,7 +2610,8 @@ static int __init dbri_attach(int prom_n err = prom_getproperty(prom_node, "intr", (char *)&irq, sizeof(irq)); if (err < 0) { - printk(KERN_ERR "DBRI-%d: Firmware node lacks IRQ property.\n", dev); + printk(KERN_ERR "DBRI-%d: Firmware node lacks IRQ property.\n", + dev); return -ENODEV; } @@ -2613,12 +2637,14 @@ static int __init dbri_attach(int prom_n goto _err; if ((err = snd_dbri_mixer(dbri)) < 0) + if ((err = snd_dbri_mixer(dbri)) < 0) goto _err; /* /proc file handling */ snd_dbri_proc(dbri); - if ((err = snd_card_register(card)) < 0) + err = snd_card_register(card); + if (err < 0) goto _err; printk(KERN_INFO "audio%d at %p (irq %d) is DBRI(%c) +CS4215(%d)\n", @@ -2628,7 +2654,7 @@ static int __init dbri_attach(int prom_n return 0; - _err: +_err: snd_dbri_free(dbri); snd_card_free(card); return err; ---------------------------------------------------- Producenci filmu SEZON NA MISIA przedstawiają surfujące pingwiny w nowej, animowanej komedii NA FALI - w kinach od 10 sierpnia! http://klik.wp.pl/?adr=http%3A%2F%2Fadv.reklama.wp.pl%2Fas%2Fnafali_zwiastu…

2 1

[alsa-devel] snd-hda-intel, AD 1988b: SPDIF output not working correctly, volume low for analog output
by Matthias Dahl 20 Aug '07

20 Aug '07

Hello everyone. I very recently upgraded my system to a Asus Crosshair (AM2, nforce 590 sli) board because it seemed just good quality. Unfortunately the AD1988b chip on it is causing me some trouble. 1] SPDIF output When I use it for dts/dolby passthrough, it works just fine even though from time to time spdif just hangs- not during playback but when I start the playback. (analog output is unaffected) Meaning that either the player is hanging or playback starts but I hear no sound. After that only a reboot solves the problem... restarting alsa has not effect. Also when the passthrough stops or during playback of anything else besides a dts/dolby stream, I hear a low pitch beating (usually in combination with a very high pitch sound) in the background. I double checked everything to be sure that my other equipment was fine and not the cause of this. 2] analog output I am unable to get it as loud as with the win drivers without overdriving it. The volume is okay... but not on par with the win drivers. That's especially true for the SPDIF output. Increasing the SPDIF volume usually results in worse audio quality over spdif and increased "noise" (see above). Like said earlier, I checked with the win drivers, and everything (audio wise) works just fine there. So it's not a hardware fault. (relief -g-) My guess would be that the AD 1988b is quite a bit different to program from its 1988 predecessors as it contains dts live and stuff. Just a guess... I have attached some hopefully useful informations. If you need anything else, please let me know. I really need that spdif working, so I am more than willing to test just about anything. :-) Last but not leat, I have tried the latest official alsa drivers as well as a mercurial snapshot from yesterday. (which I am currently using) Both show the same problems. Thanks for any help in advance, matthew.

4 10

[alsa-devel] Voip Application with ALSA OSS Emulation ==> voice delay
by Akio 20 Aug '07

20 Aug '07

Dear Sir: Could you do me a favor? Right now, we are using a arm box with linux kernel 2.6.14 to develop a voip solution. After the rtp connection was connected at first 20 secs, there is no delay. As the timing passing by, the delay will going longer and longer. After 16 houres, the delay will up to 12 secs. Because the alsa lib application can't detect any alsa device, we have no choice but only alsa oss emulation data path to using audio device. after tracing sound/core/oss/pcm_oss.c. we find some things. 1.in snd_pcm_oss_write() and in snd_pcm_oss_read(), there is a little slight difference. in snd_pcm_oss_write(), before and after snd_pcm_oss_write1() there are using up() and down() to protect snd_pcm_oss_write1(). but in snd_pcm_oss_read(), there is no protection. why doesn't use up() and down() to protect snd_pcm_oss_read1()? 2.after using printk to tracing runtime->oss.xxx fields in snd_pcm_oss_read1(), we got the data positions seem correct. and alignment very well. what should we have to check? where do we have to check? 3.in snd_pcm_oss_capture_position_fixup(), why using the following condition to check, if (*delay <= (snd_pcm_sframes_t)runtime->buffer_size)? why not using if (*delay <= (snd_pcm_sframes_t)runtime->period_size)? because the following wrapping, frames = (*delay - runtime->buffer_size) + runtime->period_size - 1; frames /= runtime->period_size; frames *= runtime->period_size; using runtime->period_size, not runtime->buffer_size. 4.why using snd_pcm_oss_capture_position_fixup() in snd_pcm_oss_read3() not in snd_pcm_oss_read()? 5.the following url seem counter the same problems. http://blackfin.uclinux.org/gf/project/uclinux-dist/forum/? action=ForumBrowse&forum_id=39&_forum_action= ForumMessageBrowse&thread_id=22524 We will check the write direction to see the runtime->oss.xxx fields will act as the same read or not. Thanks in advance. Best Regards, Akio

2 2