May 2009 - Alsa-devel - mailman.alsa-project.org

[alsa-devel] [PATCH 0/3] ASoC: TWL4030: Handsfree pop removal and mute
by Peter Ujfalusi 25 May '09

25 May '09

Hello, The following series fixes the HandsfreeL/R pop removal sequence: The pop removal is moved from the MUX_E to PGA_E DAPM control and also the sequence is modified to match with the sequence described in the TRM. Note, that the power-down sequence is not described in the TRM, it has been implemented in a way that it should make sense. HandsetL/R mute: Since all bits are needed for the pop removal and they have to modified in a strict order/timing: I have added SW_SHADOW non HW register. This register at the moment only handles the HandsfreeL/R mute. --- Peter Ujfalusi (3): ASoC: TWL4030: Handsfree pop removal redesign ASoC: TWL4030: Add shadow register ASoC: TWL4030: HandsfreeL/R mute DAPM switch sound/soc/codecs/twl4030.c | 99 +++++++++++++++++++++++++++++++++++--------- sound/soc/codecs/twl4030.h | 7 +++- 2 files changed, 85 insertions(+), 21 deletions(-)

2 5

[alsa-devel] snd_pcm_writei() return value
by Cristian Morales Vega 25 May '09

25 May '09

Hi, I have an stupid doubt... The snd_pcm_writei() documentation says: "If the blocking behaviour is selected, then routine waits until all requested bytes are played or put to the playback ring buffer. The count of bytes can be less only if a signal or underrun occurred." and at the same time it says "-EPIPE an underrun occurred" is a possible return value. Then snd_pcm_recover() documentation says: "This functions handles -EINTR (interrupted system call), -EPIPE (overrun or underrun) and -ESTRPIPE (stream is suspended) error codes trying to prepare given stream for next I/O." So if I want to write the full content of a buffer, would this be valid?: while(buffer.length > 0) { snd_pcm_sframes_t written = snd_pcm_writei(device.handle, buffer.data, buffer.length); if(written < 0) snd_pcm_recover(device.handle, written, 1); else buffer.length = 0; } "The count of bytes can be less only if a signal ... occurred." makes me think that if a signal interrups snd_pcm_writei() it will return a value between 0 and buffer.length, but "This functions handles -EINTR (interrupted system call)" makes me think that it will always return -EINTR. "The count of bytes can be less only if a ... underrun occurred.", even if technically correct, also seems to be against the "-EPIPE an underrun occurred" return value. So, in the previous code, "if(written < 0)" should be changed by "if(written < buffer.length)"? Anyway, how snd_pcm_recover() handles an -EINTR? If only half the data has been written it can't modify buffer.data to point to the last sample written+1. Perhaps I need a full: uint32_t *buffer_ptr = buffer.data; while(buffer.length > 0) { snd_pcm_sframes_t written = snd_pcm_writei(device.handle, buffer_ptr, buffer.length); if(written < 0) { snd_pcm_recover(device.handle, written, 1); } else if(written <= buffer.length) { buffer.length -= written; buffer_ptr += written; } } ? And still, in this case an interrupt would be handled by snd_pcm_recover() (written < 0) or by the "else" code? Thanks.

3 3

[alsa-devel] [PATCH] ALSA: hda - Add forced codec-slots for ASUS W5Fm
by Ozan Çağlayan 25 May '09

25 May '09

ASUS W5Fm needs the fixed codec-slots to probe to override the BIOS problem like W5F. Tested-by: Alp Kılıç <kilic.alp(a)gmail.com> Signed-off-by: Ozan Çağlayan <ozan(a)pardus.org.tr> --- sound/pci/hda/hda_intel.c | 1 + 1 files changed, 1 insertions(+), 0 deletions(-) diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c index 21e99cf..4419e11 100644 --- a/sound/pci/hda/hda_intel.c +++ b/sound/pci/hda/hda_intel.c @@ -2142,6 +2142,7 @@ static struct snd_pci_quirk probe_mask_list[] __devinitdata = { SND_PCI_QUIRK(0x17c0, 0x4085, "Medion MD96630", 0x01), /* forced codec slots */ SND_PCI_QUIRK(0x1046, 0x1262, "ASUS W5F", 0x103), + SND_PCI_QUIRK(0x1043, 0x1262, "ASUS W5Fm", 0x103), {} }; -- 1.6.2

2 7

Re: [alsa-devel] Help on writing an ALSA ASoC Driver for WM8985
by Leung Chi Tat 25 May '09

25 May '09

Thank you so much for your suggestion. I've already copied a codec source for wm8980 from linux-2.6-ASoC main trunk. I have already to modify it back to the old api's and old structures for kernel v2.6.21. What remains I can't get through are those points I listed in my previous email. Could you give me some hints? Best Regards, LEUNG, Chi Tat Senior Software Engineer CCT Tech Advanced Products Limited 18/F, CCT Telecom Building, 11 Wo Shing Street Fo Tan, Shatin, N.T., Hong Kong Tel: +852 26005276 Fax: +852 26948660 Email: ctleung(a)cct.com.hk Website: http://www.cct-tech.com.hk -----Original Message----- From: Jon Smirl [mailto:jonsmirl@gmail.com] Sent: Monday, May 25, 2009 11:45 AM To: Leung Chi Tat Cc: alsa-devel(a)alsa-project.org Subject: Re: [alsa-devel] Help on writing an ALSA ASoC Driver for WM8985 On Sun, May 24, 2009 at 11:31 PM, Leung Chi Tat <ctleung(a)cct.com.hk> wrote: > Hi all, > > I'm new to ALSA ASoC and ALSA. I'd like get some advice where I can get more information about writing an ASoC driver. I've browsed the internet couples of days and I can only find links on ALSA driver api's and writing an ALSA driver for PCI devices. > > It seems there is not much information on how to writing an ALSA ASoC driver. I'm stuck on the following questions: > 1. describing those important structures, e.g. struct soc_enum, struct snd_kcontrol_new, struct snd_soc_dapm_widget; > 2. what is/are the relationships among those important structures; > 3. what is the differences between those controls for struct snd_kcontrol_new and struct snd_soc_dapm_widget; > 4. Should those sinks, sources, paths be defined in the arrays of struct snd_dapm_widget; > 5. How can I select those defined paths through ALSA user-mode library as I can't find any examples in those ALSA tutorials; > > Indeed, I'm right now trying to write a WM8985 driver for my s3c6400 based platform based on the kernel source v2.6.21 from Samsung. Look in sound/soc/codecs. There are implementations for many similar Wolfson chips. Just cut and paste them together to make the wm8985. > > Thank you so much for your valuable advice and suggestions in advance. > > Best Regards, > LEUNG, Chi Tat > Senior Software Engineer > CCT Tech Advanced Products Limited > 18/F, CCT Telecom Building, 11 Wo Shing Street > Fo Tan, Shatin, N.T., Hong Kong > Tel: +852 26005276 Fax: +852 26948660 > Email: ctleung(a)cct.com.hk > Website: http://www.cct-tech.com.hk > > _______________________________________________ > Alsa-devel mailing list > Alsa-devel(a)alsa-project.org > http://mailman.alsa-project.org/mailman/listinfo/alsa-devel > -- Jon Smirl jonsmirl(a)gmail.com

1 0

[alsa-devel] spdif/iec958 outputs at VT1708S not recognized
by linux user 24 May '09

24 May '09

Hi I am running 2.6.28-11-generic (Kubunti install) with M4A78T-E Motherboard and also have no digital spdif output. aplay -L default:CARD=SB HDA ATI SB, VT1708S Analog Default Audio Device front:CARD=SB,DEV=0 HDA ATI SB, VT1708S Analog Front speakers surround40:CARD=SB,DEV=0 HDA ATI SB, VT1708S Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=SB,DEV=0 HDA ATI SB, VT1708S Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=SB,DEV=0 HDA ATI SB, VT1708S Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=SB,DEV=0 HDA ATI SB, VT1708S Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=SB,DEV=0 HDA ATI SB, VT1708S Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers null Discard all samples (playback) or generate zero samples (capture) hdmi:CARD=HDMI HDA ATI HDMI, ATI HDMI HDMI Audio Output I have read this thread ( http://mailman.alsa-project.org/pipermail/alsa-devel/2009-May/016958.html ) and gather that it is a problem with the BIOS and that it was fixable by patching alsa source. As a newbie and not wanting to destroy my alsa source files can you explain or refer me to a good howto of the steps needed? Thanks http://mailman.alsa-project.org/pipermail/alsa-devel/2009-May/016958.html

1 0

Re: [alsa-devel] Alsa-devel Digest, Vol 27, Issue 124
by Demian Martin 24 May '09

24 May '09

Demian Martin PDS 209 613 6990 -----Original Message----- From: alsa-devel-request(a)alsa-project.org Date: Sun, 24 May 2009 01:13:19 To: <alsa-devel(a)alsa-project.org> Subject: Alsa-devel Digest, Vol 27, Issue 124 Send Alsa-devel mailing list submissions to alsa-devel(a)alsa-project.org To subscribe or unsubscribe via the World Wide Web, visit http://mailman.alsa-project.org/mailman/listinfo/alsa-devel or, via email, send a message with subject or body 'help' to alsa-devel-request(a)alsa-project.org You can reach the person managing the list at alsa-devel-owner(a)alsa-project.org When replying, please edit your Subject line so it is more specific than "Re: Contents of Alsa-devel digest..." Today's Topics: 1. [PATCH V2 4/9] Add a few more mpc5200 PSC defines (Jon Smirl) 2. [PATCH V2 6/9] Codec for STAC9766 used on the Efika (Jon Smirl) 3. [PATCH V2 7/9] AC97 driver for mpc5200 (Jon Smirl) ---------------------------------------------------------------------- Message: 1 Date: Sat, 23 May 2009 19:13:03 -0400 From: Jon Smirl <jonsmirl(a)gmail.com> Subject: [alsa-devel] [PATCH V2 4/9] Add a few more mpc5200 PSC defines To: grant.likely(a)secretlab.ca, linuxppc-dev(a)ozlabs.org, alsa-devel(a)alsa-project.org, broonie(a)sirena.org.uk Message-ID: <20090523231303.17919.35877.stgit@terra> Content-Type: text/plain; charset="utf-8" Add a few more mpc5200 PSC defines. More bit fields defines for mpc5200 PSC registers. This patch is going in via Grant's tree. Signed-off-by: Jon Smirl <jonsmirl(a)gmail.com> --- 0 files changed, 0 insertions(+), 0 deletions(-) diff --git a/arch/powerpc/include/asm/mpc52xx_psc.h b/arch/powerpc/include/asm/mpc52xx_psc.h index a218da6..fb84120 100644 --- a/arch/powerpc/include/asm/mpc52xx_psc.h +++ b/arch/powerpc/include/asm/mpc52xx_psc.h @@ -28,6 +28,10 @@ #define MPC52xx_PSC_MAXNUM 6 /* Programmable Serial Controller (PSC) status register bits */ +#define MPC52xx_PSC_SR_UNEX_RX 0x0001 +#define MPC52xx_PSC_SR_DATA_VAL 0x0002 +#define MPC52xx_PSC_SR_DATA_OVR 0x0004 +#define MPC52xx_PSC_SR_CMDSEND 0x0008 #define MPC52xx_PSC_SR_CDE 0x0080 #define MPC52xx_PSC_SR_RXRDY 0x0100 #define MPC52xx_PSC_SR_RXFULL 0x0200 @@ -61,6 +65,12 @@ #define MPC52xx_PSC_RXTX_FIFO_EMPTY 0x0001 /* PSC interrupt status/mask bits */ +#define MPC52xx_PSC_IMR_UNEX_RX_SLOT 0x0001 +#define MPC52xx_PSC_IMR_DATA_VALID 0x0002 +#define MPC52xx_PSC_IMR_DATA_OVR 0x0004 +#define MPC52xx_PSC_IMR_CMD_SEND 0x0008 +#define MPC52xx_PSC_IMR_ERROR 0x0040 +#define MPC52xx_PSC_IMR_DEOF 0x0080 #define MPC52xx_PSC_IMR_TXRDY 0x0100 #define MPC52xx_PSC_IMR_RXRDY 0x0200 #define MPC52xx_PSC_IMR_DB 0x0400 @@ -117,6 +127,7 @@ #define MPC52xx_PSC_SICR_SIM_FIR (0x6 << 24) #define MPC52xx_PSC_SICR_SIM_CODEC_24 (0x7 << 24) #define MPC52xx_PSC_SICR_SIM_CODEC_32 (0xf << 24) +#define MPC52xx_PSC_SICR_AWR (1 << 30) #define MPC52xx_PSC_SICR_GENCLK (1 << 23) #define MPC52xx_PSC_SICR_I2S (1 << 22) #define MPC52xx_PSC_SICR_CLKPOL (1 << 21) ------------------------------ Message: 2 Date: Sat, 23 May 2009 19:13:07 -0400 From: Jon Smirl <jonsmirl(a)gmail.com> Subject: [alsa-devel] [PATCH V2 6/9] Codec for STAC9766 used on the Efika To: grant.likely(a)secretlab.ca, linuxppc-dev(a)ozlabs.org, alsa-devel(a)alsa-project.org, broonie(a)sirena.org.uk Message-ID: <20090523231307.17919.5277.stgit@terra> Content-Type: text/plain; charset="utf-8" AC97 codec for STAC9766 used on the Efika. Datasheet: http://www.idt.com/products/getDoc.cfm?docID=13134007 Signed-off-by: Jon Smirl <jonsmirl(a)gmail.com> --- 0 files changed, 0 insertions(+), 0 deletions(-) diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 7f78b65..cb07d9b 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -19,6 +19,7 @@ config SND_SOC_ALL_CODECS select SND_SOC_CS4270 if I2C select SND_SOC_PCM3008 select SND_SOC_SSM2602 if I2C + select SND_SOC_STAC9766 if SND_SOC_AC97_BUS select SND_SOC_TLV320AIC23 if I2C select SND_SOC_TLV320AIC26 if SPI_MASTER select SND_SOC_TLV320AIC3X if I2C @@ -93,6 +94,9 @@ config SND_SOC_PCM3008 config SND_SOC_SSM2602 tristate +config SND_SOC_STAC9766 + tristate + config SND_SOC_TLV320AIC23 tristate diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 70c55fa..46c007c 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -7,6 +7,7 @@ snd-soc-cs4270-objs := cs4270.o snd-soc-l3-objs := l3.o snd-soc-pcm3008-objs := pcm3008.o snd-soc-ssm2602-objs := ssm2602.o +snd-soc-stac9766-objs := stac9766.o snd-soc-tlv320aic23-objs := tlv320aic23.o snd-soc-tlv320aic26-objs := tlv320aic26.o snd-soc-tlv320aic3x-objs := tlv320aic3x.o @@ -42,6 +43,7 @@ obj-$(CONFIG_SND_SOC_CS4270) += snd-soc-cs4270.o obj-$(CONFIG_SND_SOC_L3) += snd-soc-l3.o obj-$(CONFIG_SND_SOC_PCM3008) += snd-soc-pcm3008.o obj-$(CONFIG_SND_SOC_SSM2602) += snd-soc-ssm2602.o +obj-$(CONFIG_SND_SOC_STAC9766) += snd-soc-stac9766.o obj-$(CONFIG_SND_SOC_TLV320AIC23) += snd-soc-tlv320aic23.o obj-$(CONFIG_SND_SOC_TLV320AIC26) += snd-soc-tlv320aic26.o obj-$(CONFIG_SND_SOC_TLV320AIC3X) += snd-soc-tlv320aic3x.o diff --git a/sound/soc/codecs/stac9766.c b/sound/soc/codecs/stac9766.c new file mode 100644 index 0000000..7740cd5 --- /dev/null +++ b/sound/soc/codecs/stac9766.c @@ -0,0 +1,470 @@ +/* + * stac9766.c -- ALSA SoC STAC9766 codec support + * + * Copyright 2009 Jon Smirl, Digispeaker + * Author: Jon Smirl <jonsmirl(a)gmail.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * Features:- + * + * o Support for AC97 Codec, S/PDIF + */ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/device.h> +#include <sound/core.h> +#include <sound/pcm.h> +#include <sound/ac97_codec.h> +#include <sound/initval.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/tlv.h> +#include <sound/soc-of-simple.h> + +#include "stac9766.h" + +#define STAC9766_VERSION "0.10" + +/* + * STAC9766 register cache + */ +static const u16 stac9766_reg[] = { + 0x6A90, 0x8000, 0x8000, 0x8000, /* 6 */ + 0x0000, 0x0000, 0x8008, 0x8008, /* e */ + 0x8808, 0x8808, 0x8808, 0x8808, /* 16 */ + 0x8808, 0x0000, 0x8000, 0x0000, /* 1e */ + 0x0000, 0x0000, 0x0000, 0x000f, /* 26 */ + 0x0a05, 0x0400, 0xbb80, 0x0000, /* 2e */ + 0x0000, 0xbb80, 0x0000, 0x0000, /* 36 */ + 0x0000, 0x2000, 0x0000, 0x0100, /* 3e */ + 0x0000, 0x0000, 0x0080, 0x0000, /* 46 */ + 0x0000, 0x0000, 0x0003, 0xffff, /* 4e */ + 0x0000, 0x0000, 0x0000, 0x0000, /* 56 */ + 0x4000, 0x0000, 0x0000, 0x0000, /* 5e */ + 0x1201, 0xFFFF, 0xFFFF, 0x0000, /* 66 */ + 0x0000, 0x0000, 0x0000, 0x0000, /* 6e */ + 0x0000, 0x0000, 0x0000, 0x0006, /* 76 */ + 0x0000, 0x0000, 0x0000, 0x0000, /* 7e */ +}; + +static const char *stac9766_record_mux[] = {"Mic", "CD", "Video", "AUX", "Line", "Stereo Mix", "Mono Mix", "Phone"}; +static const char *stac9766_mono_mux[] = {"Mix", "Mic"}; +static const char *stac9766_mic_mux[] = {"Mic1", "Mic2"}; +static const char *stac9766_SPDIF_mux[] = {"PCM", "ADC Record"}; +static const char *stac9766_popbypass_mux[] = {"Normal", "Bypass Mixer"}; +static const char *stac9766_record_all_mux[] = {"All analog", "Analog plus DAC"}; +static const char *stac9766_boost1[] = {"0dB", "10dB"}; +static const char *stac9766_boost2[] = {"0dB", "20dB"}; +static const char *stac9766_stereo_mic[] = {"Off", "On"}; + +static const struct soc_enum stac9766_record_enum = + SOC_ENUM_DOUBLE(AC97_REC_SEL, 8, 0, 8, stac9766_record_mux); +static const struct soc_enum stac9766_mono_enum = + SOC_ENUM_SINGLE(AC97_GENERAL_PURPOSE, 9, 2, stac9766_mono_mux); +static const struct soc_enum stac9766_mic_enum = + SOC_ENUM_SINGLE(AC97_GENERAL_PURPOSE, 8, 2, stac9766_mic_mux); +static const struct soc_enum stac9766_SPDIF_enum = + SOC_ENUM_SINGLE(AC97_STAC_DA_CONTROL, 1, 2, stac9766_SPDIF_mux); +static const struct soc_enum stac9766_popbypass_enum = + SOC_ENUM_SINGLE(AC97_GENERAL_PURPOSE, 15, 2, stac9766_popbypass_mux); +static const struct soc_enum stac9766_record_all_enum = + SOC_ENUM_SINGLE(AC97_STAC_ANALOG_SPECIAL, 12, 2, stac9766_record_all_mux); +static const struct soc_enum stac9766_boost1_enum = + SOC_ENUM_SINGLE(AC97_MIC, 6, 2, stac9766_boost1); /* 0/10dB */ +static const struct soc_enum stac9766_boost2_enum = + SOC_ENUM_SINGLE(AC97_STAC_ANALOG_SPECIAL, 2, 2, stac9766_boost2); /* 0/20dB */ +static const struct soc_enum stac9766_stereo_mic_enum = + SOC_ENUM_SINGLE(AC97_STAC_STEREO_MIC, 2, 1, stac9766_stereo_mic); + +static const DECLARE_TLV_DB_LINEAR(master_tlv, -4600, 0); +static const DECLARE_TLV_DB_LINEAR(record_tlv, 0, 2250); +static const DECLARE_TLV_DB_LINEAR(beep_tlv, -4500, 0); +static const DECLARE_TLV_DB_LINEAR(mix_tlv, -3450, 1200); + +static const struct snd_kcontrol_new stac9766_snd_ac97_controls[] = { + SOC_DOUBLE_TLV("Speaker Volume", AC97_MASTER, 8, 0, 31, 1, master_tlv), + SOC_SINGLE("Speaker Switch", AC97_MASTER, 15, 1, 1), + SOC_DOUBLE_TLV("Headphone Volume", AC97_HEADPHONE, 8, 0, 31, 1, master_tlv), + SOC_SINGLE("Headphone Switch", AC97_HEADPHONE, 15, 1, 1), + SOC_SINGLE_TLV("Mono Out Volume", AC97_MASTER_MONO, 0, 31, 1, master_tlv), + SOC_SINGLE("Mono Out Switch", AC97_MASTER_MONO, 15, 1, 1), + + SOC_DOUBLE_TLV("Record Volume", AC97_REC_GAIN, 8, 0, 15, 0, record_tlv), + SOC_SINGLE("Record Switch", AC97_REC_GAIN, 15, 1, 1), + + + SOC_SINGLE_TLV("Beep Volume", AC97_PC_BEEP, 1, 15, 1, beep_tlv), + SOC_SINGLE("Beep Switch", AC97_PC_BEEP, 15, 1, 1), + SOC_SINGLE("Beep Frequency", AC97_PC_BEEP, 5, 127, 1), + SOC_SINGLE_TLV("Phone Volume", AC97_PHONE, 0, 31, 1, mix_tlv), + SOC_SINGLE("Phone Switch", AC97_PHONE, 15, 1, 1), + + SOC_ENUM("Mic Boost1", stac9766_boost1_enum), + SOC_ENUM("Mic Boost2", stac9766_boost2_enum), + SOC_SINGLE_TLV("Mic Volume", AC97_MIC, 0, 31, 1, mix_tlv), + SOC_SINGLE("Mic Switch", AC97_MIC, 15, 1, 1), + SOC_ENUM("Stereo Mic", stac9766_stereo_mic_enum), + + SOC_DOUBLE_TLV("Line Volume", AC97_LINE, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("Line Switch", AC97_LINE, 15, 1, 1), + SOC_DOUBLE_TLV("CD Volume", AC97_CD, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("CD Switch", AC97_CD, 15, 1, 1), + SOC_DOUBLE_TLV("AUX Volume", AC97_AUX, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("AUX Switch", AC97_AUX, 15, 1, 1), + SOC_DOUBLE_TLV("Video Volume", AC97_VIDEO, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("Video Switch", AC97_VIDEO, 15, 1, 1), + + SOC_DOUBLE_TLV("DAC Volume", AC97_PCM, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("DAC Switch", AC97_PCM, 15, 1, 1), + SOC_SINGLE("Loopback Test Switch", AC97_GENERAL_PURPOSE, 7, 1, 0), + SOC_SINGLE("3D Volume", AC97_3D_CONTROL, 3, 2, 1), + SOC_SINGLE("3D Switch", AC97_GENERAL_PURPOSE, 13, 1, 0), + + SOC_ENUM("SPDIF Mux", stac9766_SPDIF_enum), + SOC_ENUM("Mic1/2 Mux", stac9766_mic_enum), + SOC_ENUM("Record All Mux", stac9766_record_all_enum), + SOC_ENUM("Record Mux", stac9766_record_enum), + SOC_ENUM("Mono Mux", stac9766_mono_enum), + SOC_ENUM("Pop Bypass Mux", stac9766_popbypass_enum), +}; + +int stac9766_ac97_write(struct snd_soc_codec *codec, unsigned int reg, + unsigned int val) +{ + u16 *cache = codec->reg_cache; + + if (reg > AC97_STAC_PAGE0) { + stac9766_ac97_write(codec, AC97_INT_PAGING, 0); + soc_ac97_ops.write(codec->ac97, reg, val); + stac9766_ac97_write(codec, AC97_INT_PAGING, 1); + return 0; + } + if (reg / 2 > ARRAY_SIZE(stac9766_reg)) + return -EIO; + + soc_ac97_ops.write(codec->ac97, reg, val); + cache[reg / 2] = val; + return 0; +} + +unsigned int stac9766_ac97_read(struct snd_soc_codec *codec, unsigned int reg) +{ + u16 val = 0, *cache = codec->reg_cache; + + if (reg > AC97_STAC_PAGE0) { + stac9766_ac97_write(codec, AC97_INT_PAGING, 0); + val = soc_ac97_ops.read(codec->ac97, reg - AC97_STAC_PAGE0); + stac9766_ac97_write(codec, AC97_INT_PAGING, 1); + return val; + } + if (reg / 2 > ARRAY_SIZE(stac9766_reg)) + return -EIO; + + if (reg == AC97_RESET || reg == AC97_GPIO_STATUS || + reg == AC97_INT_PAGING || reg == AC97_VENDOR_ID1 || + reg == AC97_VENDOR_ID2) { + + val = soc_ac97_ops.read(codec->ac97, reg); + return val; + } + return cache[reg / 2]; +} + +static int ac97_analog_prepare(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct snd_soc_codec *codec = dai->codec; + struct snd_pcm_runtime *runtime = substream->runtime; + unsigned short reg, vra; + + vra = stac9766_ac97_read(codec, AC97_EXTENDED_STATUS); + + vra |= 0x1; /* enable variable rate audio */ + + stac9766_ac97_write(codec, AC97_EXTENDED_STATUS, vra); + + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) + reg = AC97_PCM_FRONT_DAC_RATE; + else + reg = AC97_PCM_LR_ADC_RATE; + + return stac9766_ac97_write(codec, reg, runtime->rate); +} + +static int ac97_digital_prepare(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct snd_soc_codec *codec = dai->codec; + struct snd_pcm_runtime *runtime = substream->runtime; + unsigned short reg, vra; + + stac9766_ac97_write(codec, AC97_SPDIF, 0x2002); + + vra = stac9766_ac97_read(codec, AC97_EXTENDED_STATUS); + vra |= 0x5; /* Enable VRA and SPDIF out */ + + stac9766_ac97_write(codec, AC97_EXTENDED_STATUS, vra); + + reg = AC97_PCM_FRONT_DAC_RATE; + + return stac9766_ac97_write(codec, reg, runtime->rate); +} + +static int ac97_digital_trigger(struct snd_pcm_substream *substream, + int cmd, struct snd_soc_dai *dai) +{ + struct snd_soc_codec *codec = dai->codec; + unsigned short vra; + + switch (cmd) { + case SNDRV_PCM_TRIGGER_STOP: + vra = stac9766_ac97_read(codec, AC97_EXTENDED_STATUS); + vra &= !0x04; + stac9766_ac97_write(codec, AC97_EXTENDED_STATUS, vra); + break; + } + return 0; +} + +static int stac9766_set_bias_level(struct snd_soc_codec *codec, + enum snd_soc_bias_level level) +{ + switch (level) { + case SND_SOC_BIAS_ON: /* full On */ + case SND_SOC_BIAS_PREPARE: /* partial On */ + case SND_SOC_BIAS_STANDBY: /* Off, with power */ + stac9766_ac97_write(codec, AC97_POWERDOWN, 0x0000); + break; + case SND_SOC_BIAS_OFF: /* Off, without power */ + /* disable everything including AC link */ + stac9766_ac97_write(codec, AC97_POWERDOWN, 0xffff); + break; + } + codec->bias_level = level; + return 0; +} + +int stac9766_reset(struct snd_soc_codec *codec, int try_warm) +{ + if (try_warm && soc_ac97_ops.warm_reset) { + soc_ac97_ops.warm_reset(codec->ac97); + if (stac9766_ac97_read(codec, 0) == stac9766_reg[0]) + return 1; + } + + soc_ac97_ops.reset(codec->ac97); + if (soc_ac97_ops.warm_reset) + soc_ac97_ops.warm_reset(codec->ac97); + if (stac9766_ac97_read(codec, 0) != stac9766_reg[0]) + return -EIO; + return 0; +} + +static int stac9766_codec_suspend(struct platform_device *pdev, + pm_message_t state) +{ + struct snd_soc_device *socdev = platform_get_drvdata(pdev); + struct snd_soc_codec *codec = socdev->card->codec; + + stac9766_set_bias_level(codec, SND_SOC_BIAS_OFF); + return 0; +} + +static int stac9766_codec_resume(struct platform_device *pdev) +{ + struct snd_soc_device *socdev = platform_get_drvdata(pdev); + struct snd_soc_codec *codec = socdev->card->codec; + u16 id, reset; + + reset = 0; + /* give the codec an AC97 warm reset to start the link */ +reset: + if (reset > 5) { + printk(KERN_ERR "stac9766 failed to resume"); + return -EIO; + } + codec->ac97->bus->ops->warm_reset(codec->ac97); + id = soc_ac97_ops.read(codec->ac97, AC97_VENDOR_ID2); + if (id != 0x4c13) { + stac9766_reset(codec, 0); + reset++; + goto reset; + } + stac9766_set_bias_level(codec, SND_SOC_BIAS_STANDBY); + + if (codec->suspend_bias_level == SND_SOC_BIAS_ON) + stac9766_set_bias_level(codec, SND_SOC_BIAS_ON); + + return 0; +} + +static struct snd_soc_dai_ops stac9766_dai_ops_analog = +{ + .prepare = ac97_analog_prepare, +}; + +static struct snd_soc_dai_ops stac9766_dai_ops_digital = +{ + .prepare = ac97_digital_prepare, + .trigger = ac97_digital_trigger, +}; + +struct snd_soc_dai stac9766_dai[] = { +{ + .name = "stac9766 analog", + .id = 0, + .ac97_control = 1, + + /* stream cababilities */ + .playback = { + .stream_name = "stac9766 analog", + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SND_SOC_STD_AC97_FMTS, + }, + .capture = { + .stream_name = "stac9766 analog", + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SND_SOC_STD_AC97_FMTS, + }, + /* alsa ops */ + .ops = &stac9766_dai_ops_analog, +}, +{ + .name = "stac9766 IEC958", + .id = 1, + .ac97_control = 1, + + /* stream cababilities */ + .playback = { + .stream_name = "stac9766 IEC958", + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_32000 | \ + SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000, + .formats = SNDRV_PCM_FORMAT_IEC958_SUBFRAME_BE, + }, + /* alsa ops */ + .ops = &stac9766_dai_ops_digital, +}}; +EXPORT_SYMBOL_GPL(stac9766_dai); + +static int stac9766_codec_probe(struct platform_device *pdev) +{ + struct snd_soc_device *socdev = platform_get_drvdata(pdev); + struct snd_soc_codec *codec; + int ret = 0; + + printk(KERN_INFO "STAC9766 SoC Audio Codec %s\n", STAC9766_VERSION); + + socdev->card->codec = kzalloc(sizeof(struct snd_soc_codec), GFP_KERNEL); + if (socdev->card->codec == NULL) + return -ENOMEM; + codec = socdev->card->codec; + mutex_init(&codec->mutex); + + codec->reg_cache = kmemdup(stac9766_reg, sizeof(stac9766_reg), GFP_KERNEL); + if (codec->reg_cache == NULL) { + ret = -ENOMEM; + goto cache_err; + } + codec->reg_cache_size = sizeof(stac9766_reg); + codec->reg_cache_step = 2; + + codec->name = "STAC9766"; + codec->owner = THIS_MODULE; + codec->dai = stac9766_dai; + codec->num_dai = ARRAY_SIZE(stac9766_dai); + codec->write = stac9766_ac97_write; + codec->read = stac9766_ac97_read; + codec->set_bias_level = stac9766_set_bias_level; + INIT_LIST_HEAD(&codec->dapm_widgets); + INIT_LIST_HEAD(&codec->dapm_paths); + + ret = snd_soc_new_ac97_codec(codec, &soc_ac97_ops, 0); + if (ret < 0) + goto codec_err; + + /* register pcms */ + ret = snd_soc_new_pcms(socdev, SNDRV_DEFAULT_IDX1, SNDRV_DEFAULT_STR1); + if (ret < 0) + goto pcm_err; + + /* do a cold reset for the controller and then try + * a warm reset followed by an optional cold reset for codec */ + stac9766_reset(codec, 0); + ret = stac9766_reset(codec, 1); + if (ret < 0) { + printk(KERN_ERR "Failed to reset STAC9766: AC97 link error\n"); + goto reset_err; + } + + stac9766_set_bias_level(codec, SND_SOC_BIAS_STANDBY); + + snd_soc_add_controls(codec, stac9766_snd_ac97_controls, ARRAY_SIZE( + stac9766_snd_ac97_controls)); + + ret = snd_soc_init_card(socdev); + if (ret < 0) + goto reset_err; + return 0; + +reset_err: + snd_soc_free_pcms(socdev); +pcm_err: + snd_soc_free_ac97_codec(codec); +codec_err: + kfree(codec->private_data); +cache_err: + kfree(socdev->card->codec); + socdev->card->codec = NULL; + return ret; +} + +static int stac9766_codec_remove(struct platform_device *pdev) +{ + struct snd_soc_device *socdev = platform_get_drvdata(pdev); + struct snd_soc_codec *codec = socdev->card->codec; + + if (codec == NULL) + return 0; + + snd_soc_free_pcms(socdev); + snd_soc_free_ac97_codec(codec); + kfree(codec->reg_cache); + kfree(codec); + return 0; +} + +struct snd_soc_codec_device soc_codec_dev_stac9766 = +{ + .probe = stac9766_codec_probe, + .remove = stac9766_codec_remove, + .suspend = stac9766_codec_suspend, + .resume = stac9766_codec_resume, +}; +EXPORT_SYMBOL_GPL(soc_codec_dev_stac9766); + +static int __init stac9766_modinit(void) +{ + return snd_soc_register_dais(stac9766_dai, ARRAY_SIZE(stac9766_dai)); +} +module_init(stac9766_modinit); + +static void __exit stac9766_exit(void) +{ + snd_soc_unregister_dais(stac9766_dai, ARRAY_SIZE(stac9766_dai)); +} +module_exit(stac9766_exit); + +MODULE_DESCRIPTION("ASoC stac9766 driver"); +MODULE_AUTHOR("Jon Smirl <jonsmirl(a)gmail.com>"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/stac9766.h b/sound/soc/codecs/stac9766.h new file mode 100644 index 0000000..65642eb --- /dev/null +++ b/sound/soc/codecs/stac9766.h @@ -0,0 +1,21 @@ +/* + * stac9766.h -- STAC9766 Soc Audio driver + */ + +#ifndef _STAC9766_H +#define _STAC9766_H + +#define AC97_STAC_PAGE0 0x1000 +#define AC97_STAC_DA_CONTROL (AC97_STAC_PAGE0 | 0x6A) +#define AC97_STAC_ANALOG_SPECIAL (AC97_STAC_PAGE0 | 0x6E) +#define AC97_STAC_STEREO_MIC 0x78 + +/* STAC9766 DAI ID's */ +#define STAC9766_DAI_AC97_ANALOG 0 +#define STAC9766_DAI_AC97_DIGITAL 1 + +extern struct snd_soc_dai stac9766_dai[]; +extern struct snd_soc_codec_device soc_codec_dev_stac9766; + + +#endif ------------------------------ Message: 3 Date: Sat, 23 May 2009 19:13:09 -0400 From: Jon Smirl <jonsmirl(a)gmail.com> Subject: [alsa-devel] [PATCH V2 7/9] AC97 driver for mpc5200 To: grant.likely(a)secretlab.ca, linuxppc-dev(a)ozlabs.org, alsa-devel(a)alsa-project.org, broonie(a)sirena.org.uk Message-ID: <20090523231309.17919.83073.stgit@terra> Content-Type: text/plain; charset="utf-8" AC97 driver for mpc5200 Signed-off-by: Jon Smirl <jonsmirl(a)gmail.com> --- sound/soc/fsl/Kconfig | 11 + sound/soc/fsl/Makefile | 1 sound/soc/fsl/mpc5200_psc_ac97.c | 394 ++++++++++++++++++++++++++++++++++++++ sound/soc/fsl/mpc5200_psc_ac97.h | 15 + 4 files changed, 421 insertions(+), 0 deletions(-) create mode 100644 sound/soc/fsl/mpc5200_psc_ac97.c create mode 100644 sound/soc/fsl/mpc5200_psc_ac97.h diff --git a/sound/soc/fsl/Kconfig b/sound/soc/fsl/Kconfig index 1918c78..3bce952 100644 --- a/sound/soc/fsl/Kconfig +++ b/sound/soc/fsl/Kconfig @@ -29,3 +29,14 @@ config SND_SOC_MPC5200_I2S select PPC_BESTCOMM_GEN_BD help Say Y here to support the MPC5200 PSCs in I2S mode. + +config SND_SOC_MPC5200_AC97 + tristate "Freescale MPC5200 PSC in AC97 mode driver" + depends on PPC_MPC52xx && PPC_BESTCOMM + select AC97_BUS + select SND_MPC52xx_DMA + select PPC_BESTCOMM_GEN_BD + help + Say Y here to support the MPC5200 PSCs in AC97 mode. + + diff --git a/sound/soc/fsl/Makefile b/sound/soc/fsl/Makefile index 7731ef2..14631a1 100644 --- a/sound/soc/fsl/Makefile +++ b/sound/soc/fsl/Makefile @@ -13,4 +13,5 @@ obj-$(CONFIG_SND_SOC_MPC8610) += snd-soc-fsl-ssi.o snd-soc-fsl-dma.o # MPC5200 Platform Support obj-$(CONFIG_SND_MPC52xx_DMA) += mpc5200_dma.o obj-$(CONFIG_SND_SOC_MPC5200_I2S) += mpc5200_psc_i2s.o +obj-$(CONFIG_SND_SOC_MPC5200_AC97) += mpc5200_psc_ac97.o diff --git a/sound/soc/fsl/mpc5200_psc_ac97.c b/sound/soc/fsl/mpc5200_psc_ac97.c new file mode 100644 index 0000000..fa1bb9a --- /dev/null +++ b/sound/soc/fsl/mpc5200_psc_ac97.c @@ -0,0 +1,394 @@ +/* + * linux/sound/mpc5200-ac97.c -- AC97 support for the Freescale MPC52xx chip. + * + * Copyright (C) 2009 Jon Smirl, Digispeaker + * Author: Jon Smirl <jonsmirl(a)gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/of_platform.h> + +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> + +#include <asm/mpc52xx_psc.h> + +#include "mpc5200_dma.h" +#include "mpc5200_psc_ac97.h" + +#define DRV_NAME "mpc5200-psc-ac97" + +/* ALSA only supports a single AC97 device so static is recommend here */ +static struct psc_dma *psc_dma; + +static unsigned short psc_ac97_read(struct snd_ac97 *ac97, unsigned short reg) +{ + int timeout; + unsigned int val; + + spin_lock(&psc_dma->lock); + + /* Wait for it to be ready */ + timeout = 1000; + while ((--timeout) && (in_be16(&psc_dma->psc_regs->sr_csr.status) & + MPC52xx_PSC_SR_CMDSEND) ) + udelay(10); + + if (!timeout) { + pr_err("timeout on ac97 bus (rdy)\n"); + return 0xffff; + } + + /* Do the read */ + out_be32(&psc_dma->psc_regs->ac97_cmd, (1<<31) | ((reg & 0x7f) << 24)); + + /* Wait for the answer */ + timeout = 1000; + while ((--timeout) && !(in_be16(&psc_dma->psc_regs->sr_csr.status) & + MPC52xx_PSC_SR_DATA_VAL) ) + udelay(10); + + if (!timeout) { + pr_err("timeout on ac97 read (val) %x\n", in_be16(&psc_dma->psc_regs->sr_csr.status)); + return 0xffff; + } + + /* Get the data */ + val = in_be32(&psc_dma->psc_regs->ac97_data); + if ( ((val>>24) & 0x7f) != reg ) { + pr_err("reg echo error on ac97 read\n"); + return 0xffff; + } + val = (val >> 8) & 0xffff; + + spin_unlock(&psc_dma->lock); + return (unsigned short) val; +} + +static void psc_ac97_write(struct snd_ac97 *ac97, unsigned short reg, unsigned short val) +{ + int timeout; + + spin_lock(&psc_dma->lock); + + /* Wait for it to be ready */ + timeout = 1000; + while ((--timeout) && (in_be16(&psc_dma->psc_regs->sr_csr.status) & + MPC52xx_PSC_SR_CMDSEND) ) + udelay(10); + + if (!timeout) { + pr_err("timeout on ac97 write\n"); + return; + } + + /* Write data */ + out_be32(&psc_dma->psc_regs->ac97_cmd, ((reg & 0x7f) << 24) | (val << 8)); + + spin_unlock(&psc_dma->lock); +} + +static void psc_ac97_cold_reset(struct snd_ac97 *ac97) +{ + struct mpc52xx_psc __iomem *regs = psc_dma->psc_regs; + + /* Do a cold reset */ + out_8(&regs->op1, MPC52xx_PSC_OP_RES); + udelay(10); + out_8(&regs->op0, MPC52xx_PSC_OP_RES); + udelay(50); + + /* PSC recover from cold reset (cfr user manual, not sure if useful) */ + out_be32(&regs->sicr, in_be32(&regs->sicr)); +} + +static void psc_ac97_warm_reset(struct snd_ac97 *ac97) +{ + struct mpc52xx_psc __iomem *regs = psc_dma->psc_regs; + + out_be32(&regs->sicr, psc_dma->sicr | MPC52xx_PSC_SICR_AWR); + udelay(3); + out_be32(&regs->sicr, psc_dma->sicr); +} + +struct snd_ac97_bus_ops soc_ac97_ops = { + .read = psc_ac97_read, + .write = psc_ac97_write, + .reset = psc_ac97_cold_reset, + .warm_reset = psc_ac97_warm_reset, +}; +EXPORT_SYMBOL_GPL(soc_ac97_ops); + +#ifdef CONFIG_PM +static int psc_ac97_suspend(struct snd_soc_dai *dai) +{ + return 0; +} + +static int psc_ac97_resume(struct snd_soc_dai *dai) +{ + return 0; +} + +#else +#define psc_ac97_suspend NULL +#define psc_ac97_resume NULL +#endif + +static int psc_ac97_hw_analog_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data; + + dev_dbg(psc_dma->dev, "%s(substream=%p) p_size=%i p_bytes=%i" + " periods=%i buffer_size=%i buffer_bytes=%i channels=%i" + " rate=%i format=%i\n", + __func__, substream, params_period_size(params), + params_period_bytes(params), params_periods(params), + params_buffer_size(params), params_buffer_bytes(params), + params_channels(params), params_rate(params), params_format(params)); + + + if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE) { + if (params_channels(params) == 1) + psc_dma->slots |= 0x00000100; + else + psc_dma->slots |= 0x00000300; + } else { + if (params_channels(params) == 1) + psc_dma->slots |= 0x01000000; + else + psc_dma->slots |= 0x03000000; + } + + spin_lock(&psc_dma->lock); + out_be32(&psc_dma->psc_regs->ac97_slots, psc_dma->slots); + spin_unlock(&psc_dma->lock); + + return 0; +} + +static int psc_ac97_hw_digital_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data; + + spin_lock(&psc_dma->lock); + if (params_channels(params) == 1) + out_be32(&psc_dma->psc_regs->ac97_slots, 0x01000000); + else + out_be32(&psc_dma->psc_regs->ac97_slots, 0x03000000); + spin_unlock(&psc_dma->lock); + + return 0; +} + +static int psc_ac97_trigger(struct snd_pcm_substream *substream, int cmd, + struct snd_soc_dai *dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data; + + switch (cmd) { + case SNDRV_PCM_TRIGGER_STOP: + if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE) + psc_dma->slots &= 0xFFFF0000; + else + psc_dma->slots &= 0x0000FFFF; + + spin_lock(&psc_dma->lock); + out_be32(&psc_dma->psc_regs->ac97_slots, psc_dma->slots); + spin_unlock(&psc_dma->lock); + break; + } + return 0; +} + +/* --------------------------------------------------------------------- + * ALSA SoC Bindings + * + * - Digital Audio Interface (DAI) template + * - create/destroy dai hooks + */ + +/** + * psc_ac97_dai_template: template CPU Digital Audio Interface + */ +static struct snd_soc_dai_ops psc_ac97_analog_ops = { + .hw_params = psc_ac97_hw_analog_params, + .trigger = psc_ac97_trigger, +}; + +static struct snd_soc_dai_ops psc_ac97_digital_ops = { + .hw_params = psc_ac97_hw_digital_params, +}; + +struct snd_soc_dai psc_ac97_dai[] = { +{ + .name = "AC97", + .suspend = psc_ac97_suspend, + .resume = psc_ac97_resume, + .playback = { + .channels_min = 1, + .channels_max = 6, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SNDRV_PCM_FMTBIT_S32_BE, + }, + .capture = { + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SNDRV_PCM_FMTBIT_S32_BE, + }, + .ops = &psc_ac97_analog_ops, +}, +{ + .name = "SPDIF", + .playback = { + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_32000 | \ + SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000, + .formats = SNDRV_PCM_FMTBIT_IEC958_SUBFRAME_BE, + }, + .ops = &psc_ac97_digital_ops, +}}; +EXPORT_SYMBOL_GPL(psc_ac97_dai); + + + +/* --------------------------------------------------------------------- + * OF platform bus binding code: + * - Probe/remove operations + * - OF device match table + */ +static int __devinit psc_ac97_of_probe(struct of_device *op, + const struct of_device_id *match) +{ + int rc, i, id1, id2, timeout, max_reset; + struct snd_ac97 ac97; + struct mpc52xx_psc __iomem *regs; + + rc = mpc5200_audio_dma_create(op); + if (rc != 0) + return rc; + + for (i = 0; i < ARRAY_SIZE(psc_ac97_dai); i++) + psc_ac97_dai[i].dev = &op->dev; + + rc = snd_soc_register_dais(psc_ac97_dai, ARRAY_SIZE(psc_ac97_dai)); + if (rc != 0) { + pr_err("Failed to register DAI\n"); + return 0; + } + + psc_dma = dev_get_drvdata(&op->dev); + regs = psc_dma->psc_regs; + ac97.private_data = psc_dma; + + for (i = 0; i < ARRAY_SIZE(psc_ac97_dai); i++) + psc_ac97_dai[i].private_data = psc_dma; + + psc_dma->imr = 0; + out_be16(&psc_dma->psc_regs->isr_imr.imr, psc_dma->imr); + + /* Configure the serial interface mode to AC97 */ + psc_dma->sicr = MPC52xx_PSC_SICR_SIM_AC97 | MPC52xx_PSC_SICR_ENAC97; + out_be32(&regs->sicr, psc_dma->sicr); + + /* No slots active */ + out_be32(&regs->ac97_slots, 0x00000000); + + /* AC97 clock is generated by the codec. + * Ensure that it starts ticking after codec reset. + */ + max_reset = 0; +reset: + if (max_reset++ > 5) { + dev_err(&op->dev, "AC97 codec failed to reset\n"); + mpc5200_audio_dma_destroy(op); + return -ENODEV; + } + + psc_ac97_cold_reset(&ac97); + psc_ac97_warm_reset(&ac97); + + /* first make sure it is low */ + timeout = 0; + while ((in_8(&regs->ipcr_acr.ipcr) & 0x80) != 0) { + udelay(1); + if (timeout++ > 1000) + goto reset; + } + /* then wait for the transition to high */ + timeout = 0; + while ((in_8(&regs->ipcr_acr.ipcr) & 0x80) == 0) { + udelay(1); + if (timeout++ > 1000) + psc_ac97_warm_reset(&ac97); + } + + /* Go */ + out_8(&regs->command, MPC52xx_PSC_TX_ENABLE | MPC52xx_PSC_RX_ENABLE); + + id1 = psc_ac97_read(&ac97, AC97_VENDOR_ID1); + id2 = psc_ac97_read(&ac97, AC97_VENDOR_ID2); + + dev_info(&op->dev, "Codec ID is %04x %04x\n", id1, id2); + + return 0; +} + +static int __devexit psc_ac97_of_remove(struct of_device *op) +{ + return mpc5200_audio_dma_destroy(op); +} + +/* Match table for of_platform binding */ +static struct of_device_id psc_ac97_match[] __devinitdata = { + { .compatible = "fsl,mpc5200-psc-ac97", }, + { .compatible = "fsl,mpc5200b-psc-ac97", }, + {} +}; +MODULE_DEVICE_TABLE(of, psc_ac97_match); + +static struct of_platform_driver psc_ac97_driver = { + .match_table = psc_ac97_match, + .probe = psc_ac97_of_probe, + .remove = __devexit_p(psc_ac97_of_remove), + .driver = { + .name = "mpc5200-psc-ac97", + .owner = THIS_MODULE, + }, +}; + +/* --------------------------------------------------------------------- + * Module setup and teardown; simply register the of_platform driver + * for the PSC in AC97 mode. + */ +static int __init psc_ac97_init(void) +{ + return of_register_platform_driver(&psc_ac97_driver); +} +module_init(psc_ac97_init); + +static void __exit psc_ac97_exit(void) +{ + of_unregister_platform_driver(&psc_ac97_driver); +} +module_exit(psc_ac97_exit); + +MODULE_AUTHOR("Jon Smirl <jonsmirl(a)gmail.com>"); +MODULE_DESCRIPTION("mpc5200 AC97 module"); +MODULE_LICENSE("GPL"); + diff --git a/sound/soc/fsl/mpc5200_psc_ac97.h b/sound/soc/fsl/mpc5200_psc_ac97.h new file mode 100644 index 0000000..4bc18c3 --- /dev/null +++ b/sound/soc/fsl/mpc5200_psc_ac97.h @@ -0,0 +1,15 @@ +/* + * Freescale MPC5200 PSC in AC97 mode + * ALSA SoC Digital Audio Interface (DAI) driver + * + */ + +#ifndef __SOUND_SOC_FSL_MPC52xx_PSC_AC97_H__ +#define __SOUND_SOC_FSL_MPC52xx_PSC_AC97_H__ + +extern struct snd_soc_dai psc_ac97_dai[]; + +#define MPC5200_AC97_NORMAL 0 +#define MPC5200_AC97_SPDIF 1 + +#endif /* __SOUND_SOC_FSL_MPC52xx_PSC_AC97_H__ */ ------------------------------ _______________________________________________ Alsa-devel mailing list Alsa-devel(a)alsa-project.org http://mailman.alsa-project.org/mailman/listinfo/alsa-devel End of Alsa-devel Digest, Vol 27, Issue 124 *******************************************

1 0

Re: [alsa-devel] Alsa-devel Digest, Vol 27, Issue 124
by Demian Martin 24 May '09

24 May '09

Demian Martin PDS 209 613 6990 -----Original Message----- From: alsa-devel-request(a)alsa-project.org Date: Sun, 24 May 2009 01:13:19 To: <alsa-devel(a)alsa-project.org> Subject: Alsa-devel Digest, Vol 27, Issue 124 Send Alsa-devel mailing list submissions to alsa-devel(a)alsa-project.org To subscribe or unsubscribe via the World Wide Web, visit http://mailman.alsa-project.org/mailman/listinfo/alsa-devel or, via email, send a message with subject or body 'help' to alsa-devel-request(a)alsa-project.org You can reach the person managing the list at alsa-devel-owner(a)alsa-project.org When replying, please edit your Subject line so it is more specific than "Re: Contents of Alsa-devel digest..." Today's Topics: 1. [PATCH V2 4/9] Add a few more mpc5200 PSC defines (Jon Smirl) 2. [PATCH V2 6/9] Codec for STAC9766 used on the Efika (Jon Smirl) 3. [PATCH V2 7/9] AC97 driver for mpc5200 (Jon Smirl) ---------------------------------------------------------------------- Message: 1 Date: Sat, 23 May 2009 19:13:03 -0400 From: Jon Smirl <jonsmirl(a)gmail.com> Subject: [alsa-devel] [PATCH V2 4/9] Add a few more mpc5200 PSC defines To: grant.likely(a)secretlab.ca, linuxppc-dev(a)ozlabs.org, alsa-devel(a)alsa-project.org, broonie(a)sirena.org.uk Message-ID: <20090523231303.17919.35877.stgit@terra> Content-Type: text/plain; charset="utf-8" Add a few more mpc5200 PSC defines. More bit fields defines for mpc5200 PSC registers. This patch is going in via Grant's tree. Signed-off-by: Jon Smirl <jonsmirl(a)gmail.com> --- 0 files changed, 0 insertions(+), 0 deletions(-) diff --git a/arch/powerpc/include/asm/mpc52xx_psc.h b/arch/powerpc/include/asm/mpc52xx_psc.h index a218da6..fb84120 100644 --- a/arch/powerpc/include/asm/mpc52xx_psc.h +++ b/arch/powerpc/include/asm/mpc52xx_psc.h @@ -28,6 +28,10 @@ #define MPC52xx_PSC_MAXNUM 6 /* Programmable Serial Controller (PSC) status register bits */ +#define MPC52xx_PSC_SR_UNEX_RX 0x0001 +#define MPC52xx_PSC_SR_DATA_VAL 0x0002 +#define MPC52xx_PSC_SR_DATA_OVR 0x0004 +#define MPC52xx_PSC_SR_CMDSEND 0x0008 #define MPC52xx_PSC_SR_CDE 0x0080 #define MPC52xx_PSC_SR_RXRDY 0x0100 #define MPC52xx_PSC_SR_RXFULL 0x0200 @@ -61,6 +65,12 @@ #define MPC52xx_PSC_RXTX_FIFO_EMPTY 0x0001 /* PSC interrupt status/mask bits */ +#define MPC52xx_PSC_IMR_UNEX_RX_SLOT 0x0001 +#define MPC52xx_PSC_IMR_DATA_VALID 0x0002 +#define MPC52xx_PSC_IMR_DATA_OVR 0x0004 +#define MPC52xx_PSC_IMR_CMD_SEND 0x0008 +#define MPC52xx_PSC_IMR_ERROR 0x0040 +#define MPC52xx_PSC_IMR_DEOF 0x0080 #define MPC52xx_PSC_IMR_TXRDY 0x0100 #define MPC52xx_PSC_IMR_RXRDY 0x0200 #define MPC52xx_PSC_IMR_DB 0x0400 @@ -117,6 +127,7 @@ #define MPC52xx_PSC_SICR_SIM_FIR (0x6 << 24) #define MPC52xx_PSC_SICR_SIM_CODEC_24 (0x7 << 24) #define MPC52xx_PSC_SICR_SIM_CODEC_32 (0xf << 24) +#define MPC52xx_PSC_SICR_AWR (1 << 30) #define MPC52xx_PSC_SICR_GENCLK (1 << 23) #define MPC52xx_PSC_SICR_I2S (1 << 22) #define MPC52xx_PSC_SICR_CLKPOL (1 << 21) ------------------------------ Message: 2 Date: Sat, 23 May 2009 19:13:07 -0400 From: Jon Smirl <jonsmirl(a)gmail.com> Subject: [alsa-devel] [PATCH V2 6/9] Codec for STAC9766 used on the Efika To: grant.likely(a)secretlab.ca, linuxppc-dev(a)ozlabs.org, alsa-devel(a)alsa-project.org, broonie(a)sirena.org.uk Message-ID: <20090523231307.17919.5277.stgit@terra> Content-Type: text/plain; charset="utf-8" AC97 codec for STAC9766 used on the Efika. Datasheet: http://www.idt.com/products/getDoc.cfm?docID=13134007 Signed-off-by: Jon Smirl <jonsmirl(a)gmail.com> --- 0 files changed, 0 insertions(+), 0 deletions(-) diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 7f78b65..cb07d9b 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -19,6 +19,7 @@ config SND_SOC_ALL_CODECS select SND_SOC_CS4270 if I2C select SND_SOC_PCM3008 select SND_SOC_SSM2602 if I2C + select SND_SOC_STAC9766 if SND_SOC_AC97_BUS select SND_SOC_TLV320AIC23 if I2C select SND_SOC_TLV320AIC26 if SPI_MASTER select SND_SOC_TLV320AIC3X if I2C @@ -93,6 +94,9 @@ config SND_SOC_PCM3008 config SND_SOC_SSM2602 tristate +config SND_SOC_STAC9766 + tristate + config SND_SOC_TLV320AIC23 tristate diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 70c55fa..46c007c 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -7,6 +7,7 @@ snd-soc-cs4270-objs := cs4270.o snd-soc-l3-objs := l3.o snd-soc-pcm3008-objs := pcm3008.o snd-soc-ssm2602-objs := ssm2602.o +snd-soc-stac9766-objs := stac9766.o snd-soc-tlv320aic23-objs := tlv320aic23.o snd-soc-tlv320aic26-objs := tlv320aic26.o snd-soc-tlv320aic3x-objs := tlv320aic3x.o @@ -42,6 +43,7 @@ obj-$(CONFIG_SND_SOC_CS4270) += snd-soc-cs4270.o obj-$(CONFIG_SND_SOC_L3) += snd-soc-l3.o obj-$(CONFIG_SND_SOC_PCM3008) += snd-soc-pcm3008.o obj-$(CONFIG_SND_SOC_SSM2602) += snd-soc-ssm2602.o +obj-$(CONFIG_SND_SOC_STAC9766) += snd-soc-stac9766.o obj-$(CONFIG_SND_SOC_TLV320AIC23) += snd-soc-tlv320aic23.o obj-$(CONFIG_SND_SOC_TLV320AIC26) += snd-soc-tlv320aic26.o obj-$(CONFIG_SND_SOC_TLV320AIC3X) += snd-soc-tlv320aic3x.o diff --git a/sound/soc/codecs/stac9766.c b/sound/soc/codecs/stac9766.c new file mode 100644 index 0000000..7740cd5 --- /dev/null +++ b/sound/soc/codecs/stac9766.c @@ -0,0 +1,470 @@ +/* + * stac9766.c -- ALSA SoC STAC9766 codec support + * + * Copyright 2009 Jon Smirl, Digispeaker + * Author: Jon Smirl <jonsmirl(a)gmail.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * Features:- + * + * o Support for AC97 Codec, S/PDIF + */ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/device.h> +#include <sound/core.h> +#include <sound/pcm.h> +#include <sound/ac97_codec.h> +#include <sound/initval.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/tlv.h> +#include <sound/soc-of-simple.h> + +#include "stac9766.h" + +#define STAC9766_VERSION "0.10" + +/* + * STAC9766 register cache + */ +static const u16 stac9766_reg[] = { + 0x6A90, 0x8000, 0x8000, 0x8000, /* 6 */ + 0x0000, 0x0000, 0x8008, 0x8008, /* e */ + 0x8808, 0x8808, 0x8808, 0x8808, /* 16 */ + 0x8808, 0x0000, 0x8000, 0x0000, /* 1e */ + 0x0000, 0x0000, 0x0000, 0x000f, /* 26 */ + 0x0a05, 0x0400, 0xbb80, 0x0000, /* 2e */ + 0x0000, 0xbb80, 0x0000, 0x0000, /* 36 */ + 0x0000, 0x2000, 0x0000, 0x0100, /* 3e */ + 0x0000, 0x0000, 0x0080, 0x0000, /* 46 */ + 0x0000, 0x0000, 0x0003, 0xffff, /* 4e */ + 0x0000, 0x0000, 0x0000, 0x0000, /* 56 */ + 0x4000, 0x0000, 0x0000, 0x0000, /* 5e */ + 0x1201, 0xFFFF, 0xFFFF, 0x0000, /* 66 */ + 0x0000, 0x0000, 0x0000, 0x0000, /* 6e */ + 0x0000, 0x0000, 0x0000, 0x0006, /* 76 */ + 0x0000, 0x0000, 0x0000, 0x0000, /* 7e */ +}; + +static const char *stac9766_record_mux[] = {"Mic", "CD", "Video", "AUX", "Line", "Stereo Mix", "Mono Mix", "Phone"}; +static const char *stac9766_mono_mux[] = {"Mix", "Mic"}; +static const char *stac9766_mic_mux[] = {"Mic1", "Mic2"}; +static const char *stac9766_SPDIF_mux[] = {"PCM", "ADC Record"}; +static const char *stac9766_popbypass_mux[] = {"Normal", "Bypass Mixer"}; +static const char *stac9766_record_all_mux[] = {"All analog", "Analog plus DAC"}; +static const char *stac9766_boost1[] = {"0dB", "10dB"}; +static const char *stac9766_boost2[] = {"0dB", "20dB"}; +static const char *stac9766_stereo_mic[] = {"Off", "On"}; + +static const struct soc_enum stac9766_record_enum = + SOC_ENUM_DOUBLE(AC97_REC_SEL, 8, 0, 8, stac9766_record_mux); +static const struct soc_enum stac9766_mono_enum = + SOC_ENUM_SINGLE(AC97_GENERAL_PURPOSE, 9, 2, stac9766_mono_mux); +static const struct soc_enum stac9766_mic_enum = + SOC_ENUM_SINGLE(AC97_GENERAL_PURPOSE, 8, 2, stac9766_mic_mux); +static const struct soc_enum stac9766_SPDIF_enum = + SOC_ENUM_SINGLE(AC97_STAC_DA_CONTROL, 1, 2, stac9766_SPDIF_mux); +static const struct soc_enum stac9766_popbypass_enum = + SOC_ENUM_SINGLE(AC97_GENERAL_PURPOSE, 15, 2, stac9766_popbypass_mux); +static const struct soc_enum stac9766_record_all_enum = + SOC_ENUM_SINGLE(AC97_STAC_ANALOG_SPECIAL, 12, 2, stac9766_record_all_mux); +static const struct soc_enum stac9766_boost1_enum = + SOC_ENUM_SINGLE(AC97_MIC, 6, 2, stac9766_boost1); /* 0/10dB */ +static const struct soc_enum stac9766_boost2_enum = + SOC_ENUM_SINGLE(AC97_STAC_ANALOG_SPECIAL, 2, 2, stac9766_boost2); /* 0/20dB */ +static const struct soc_enum stac9766_stereo_mic_enum = + SOC_ENUM_SINGLE(AC97_STAC_STEREO_MIC, 2, 1, stac9766_stereo_mic); + +static const DECLARE_TLV_DB_LINEAR(master_tlv, -4600, 0); +static const DECLARE_TLV_DB_LINEAR(record_tlv, 0, 2250); +static const DECLARE_TLV_DB_LINEAR(beep_tlv, -4500, 0); +static const DECLARE_TLV_DB_LINEAR(mix_tlv, -3450, 1200); + +static const struct snd_kcontrol_new stac9766_snd_ac97_controls[] = { + SOC_DOUBLE_TLV("Speaker Volume", AC97_MASTER, 8, 0, 31, 1, master_tlv), + SOC_SINGLE("Speaker Switch", AC97_MASTER, 15, 1, 1), + SOC_DOUBLE_TLV("Headphone Volume", AC97_HEADPHONE, 8, 0, 31, 1, master_tlv), + SOC_SINGLE("Headphone Switch", AC97_HEADPHONE, 15, 1, 1), + SOC_SINGLE_TLV("Mono Out Volume", AC97_MASTER_MONO, 0, 31, 1, master_tlv), + SOC_SINGLE("Mono Out Switch", AC97_MASTER_MONO, 15, 1, 1), + + SOC_DOUBLE_TLV("Record Volume", AC97_REC_GAIN, 8, 0, 15, 0, record_tlv), + SOC_SINGLE("Record Switch", AC97_REC_GAIN, 15, 1, 1), + + + SOC_SINGLE_TLV("Beep Volume", AC97_PC_BEEP, 1, 15, 1, beep_tlv), + SOC_SINGLE("Beep Switch", AC97_PC_BEEP, 15, 1, 1), + SOC_SINGLE("Beep Frequency", AC97_PC_BEEP, 5, 127, 1), + SOC_SINGLE_TLV("Phone Volume", AC97_PHONE, 0, 31, 1, mix_tlv), + SOC_SINGLE("Phone Switch", AC97_PHONE, 15, 1, 1), + + SOC_ENUM("Mic Boost1", stac9766_boost1_enum), + SOC_ENUM("Mic Boost2", stac9766_boost2_enum), + SOC_SINGLE_TLV("Mic Volume", AC97_MIC, 0, 31, 1, mix_tlv), + SOC_SINGLE("Mic Switch", AC97_MIC, 15, 1, 1), + SOC_ENUM("Stereo Mic", stac9766_stereo_mic_enum), + + SOC_DOUBLE_TLV("Line Volume", AC97_LINE, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("Line Switch", AC97_LINE, 15, 1, 1), + SOC_DOUBLE_TLV("CD Volume", AC97_CD, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("CD Switch", AC97_CD, 15, 1, 1), + SOC_DOUBLE_TLV("AUX Volume", AC97_AUX, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("AUX Switch", AC97_AUX, 15, 1, 1), + SOC_DOUBLE_TLV("Video Volume", AC97_VIDEO, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("Video Switch", AC97_VIDEO, 15, 1, 1), + + SOC_DOUBLE_TLV("DAC Volume", AC97_PCM, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("DAC Switch", AC97_PCM, 15, 1, 1), + SOC_SINGLE("Loopback Test Switch", AC97_GENERAL_PURPOSE, 7, 1, 0), + SOC_SINGLE("3D Volume", AC97_3D_CONTROL, 3, 2, 1), + SOC_SINGLE("3D Switch", AC97_GENERAL_PURPOSE, 13, 1, 0), + + SOC_ENUM("SPDIF Mux", stac9766_SPDIF_enum), + SOC_ENUM("Mic1/2 Mux", stac9766_mic_enum), + SOC_ENUM("Record All Mux", stac9766_record_all_enum), + SOC_ENUM("Record Mux", stac9766_record_enum), + SOC_ENUM("Mono Mux", stac9766_mono_enum), + SOC_ENUM("Pop Bypass Mux", stac9766_popbypass_enum), +}; + +int stac9766_ac97_write(struct snd_soc_codec *codec, unsigned int reg, + unsigned int val) +{ + u16 *cache = codec->reg_cache; + + if (reg > AC97_STAC_PAGE0) { + stac9766_ac97_write(codec, AC97_INT_PAGING, 0); + soc_ac97_ops.write(codec->ac97, reg, val); + stac9766_ac97_write(codec, AC97_INT_PAGING, 1); + return 0; + } + if (reg / 2 > ARRAY_SIZE(stac9766_reg)) + return -EIO; + + soc_ac97_ops.write(codec->ac97, reg, val); + cache[reg / 2] = val; + return 0; +} + +unsigned int stac9766_ac97_read(struct snd_soc_codec *codec, unsigned int reg) +{ + u16 val = 0, *cache = codec->reg_cache; + + if (reg > AC97_STAC_PAGE0) { + stac9766_ac97_write(codec, AC97_INT_PAGING, 0); + val = soc_ac97_ops.read(codec->ac97, reg - AC97_STAC_PAGE0); + stac9766_ac97_write(codec, AC97_INT_PAGING, 1); + return val; + } + if (reg / 2 > ARRAY_SIZE(stac9766_reg)) + return -EIO; + + if (reg == AC97_RESET || reg == AC97_GPIO_STATUS || + reg == AC97_INT_PAGING || reg == AC97_VENDOR_ID1 || + reg == AC97_VENDOR_ID2) { + + val = soc_ac97_ops.read(codec->ac97, reg); + return val; + } + return cache[reg / 2]; +} + +static int ac97_analog_prepare(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct snd_soc_codec *codec = dai->codec; + struct snd_pcm_runtime *runtime = substream->runtime; + unsigned short reg, vra; + + vra = stac9766_ac97_read(codec, AC97_EXTENDED_STATUS); + + vra |= 0x1; /* enable variable rate audio */ + + stac9766_ac97_write(codec, AC97_EXTENDED_STATUS, vra); + + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) + reg = AC97_PCM_FRONT_DAC_RATE; + else + reg = AC97_PCM_LR_ADC_RATE; + + return stac9766_ac97_write(codec, reg, runtime->rate); +} + +static int ac97_digital_prepare(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct snd_soc_codec *codec = dai->codec; + struct snd_pcm_runtime *runtime = substream->runtime; + unsigned short reg, vra; + + stac9766_ac97_write(codec, AC97_SPDIF, 0x2002); + + vra = stac9766_ac97_read(codec, AC97_EXTENDED_STATUS); + vra |= 0x5; /* Enable VRA and SPDIF out */ + + stac9766_ac97_write(codec, AC97_EXTENDED_STATUS, vra); + + reg = AC97_PCM_FRONT_DAC_RATE; + + return stac9766_ac97_write(codec, reg, runtime->rate); +} + +static int ac97_digital_trigger(struct snd_pcm_substream *substream, + int cmd, struct snd_soc_dai *dai) +{ + struct snd_soc_codec *codec = dai->codec; + unsigned short vra; + + switch (cmd) { + case SNDRV_PCM_TRIGGER_STOP: + vra = stac9766_ac97_read(codec, AC97_EXTENDED_STATUS); + vra &= !0x04; + stac9766_ac97_write(codec, AC97_EXTENDED_STATUS, vra); + break; + } + return 0; +} + +static int stac9766_set_bias_level(struct snd_soc_codec *codec, + enum snd_soc_bias_level level) +{ + switch (level) { + case SND_SOC_BIAS_ON: /* full On */ + case SND_SOC_BIAS_PREPARE: /* partial On */ + case SND_SOC_BIAS_STANDBY: /* Off, with power */ + stac9766_ac97_write(codec, AC97_POWERDOWN, 0x0000); + break; + case SND_SOC_BIAS_OFF: /* Off, without power */ + /* disable everything including AC link */ + stac9766_ac97_write(codec, AC97_POWERDOWN, 0xffff); + break; + } + codec->bias_level = level; + return 0; +} + +int stac9766_reset(struct snd_soc_codec *codec, int try_warm) +{ + if (try_warm && soc_ac97_ops.warm_reset) { + soc_ac97_ops.warm_reset(codec->ac97); + if (stac9766_ac97_read(codec, 0) == stac9766_reg[0]) + return 1; + } + + soc_ac97_ops.reset(codec->ac97); + if (soc_ac97_ops.warm_reset) + soc_ac97_ops.warm_reset(codec->ac97); + if (stac9766_ac97_read(codec, 0) != stac9766_reg[0]) + return -EIO; + return 0; +} + +static int stac9766_codec_suspend(struct platform_device *pdev, + pm_message_t state) +{ + struct snd_soc_device *socdev = platform_get_drvdata(pdev); + struct snd_soc_codec *codec = socdev->card->codec; + + stac9766_set_bias_level(codec, SND_SOC_BIAS_OFF); + return 0; +} + +static int stac9766_codec_resume(struct platform_device *pdev) +{ + struct snd_soc_device *socdev = platform_get_drvdata(pdev); + struct snd_soc_codec *codec = socdev->card->codec; + u16 id, reset; + + reset = 0; + /* give the codec an AC97 warm reset to start the link */ +reset: + if (reset > 5) { + printk(KERN_ERR "stac9766 failed to resume"); + return -EIO; + } + codec->ac97->bus->ops->warm_reset(codec->ac97); + id = soc_ac97_ops.read(codec->ac97, AC97_VENDOR_ID2); + if (id != 0x4c13) { + stac9766_reset(codec, 0); + reset++; + goto reset; + } + stac9766_set_bias_level(codec, SND_SOC_BIAS_STANDBY); + + if (codec->suspend_bias_level == SND_SOC_BIAS_ON) + stac9766_set_bias_level(codec, SND_SOC_BIAS_ON); + + return 0; +} + +static struct snd_soc_dai_ops stac9766_dai_ops_analog = +{ + .prepare = ac97_analog_prepare, +}; + +static struct snd_soc_dai_ops stac9766_dai_ops_digital = +{ + .prepare = ac97_digital_prepare, + .trigger = ac97_digital_trigger, +}; + +struct snd_soc_dai stac9766_dai[] = { +{ + .name = "stac9766 analog", + .id = 0, + .ac97_control = 1, + + /* stream cababilities */ + .playback = { + .stream_name = "stac9766 analog", + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SND_SOC_STD_AC97_FMTS, + }, + .capture = { + .stream_name = "stac9766 analog", + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SND_SOC_STD_AC97_FMTS, + }, + /* alsa ops */ + .ops = &stac9766_dai_ops_analog, +}, +{ + .name = "stac9766 IEC958", + .id = 1, + .ac97_control = 1, + + /* stream cababilities */ + .playback = { + .stream_name = "stac9766 IEC958", + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_32000 | \ + SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000, + .formats = SNDRV_PCM_FORMAT_IEC958_SUBFRAME_BE, + }, + /* alsa ops */ + .ops = &stac9766_dai_ops_digital, +}}; +EXPORT_SYMBOL_GPL(stac9766_dai); + +static int stac9766_codec_probe(struct platform_device *pdev) +{ + struct snd_soc_device *socdev = platform_get_drvdata(pdev); + struct snd_soc_codec *codec; + int ret = 0; + + printk(KERN_INFO "STAC9766 SoC Audio Codec %s\n", STAC9766_VERSION); + + socdev->card->codec = kzalloc(sizeof(struct snd_soc_codec), GFP_KERNEL); + if (socdev->card->codec == NULL) + return -ENOMEM; + codec = socdev->card->codec; + mutex_init(&codec->mutex); + + codec->reg_cache = kmemdup(stac9766_reg, sizeof(stac9766_reg), GFP_KERNEL); + if (codec->reg_cache == NULL) { + ret = -ENOMEM; + goto cache_err; + } + codec->reg_cache_size = sizeof(stac9766_reg); + codec->reg_cache_step = 2; + + codec->name = "STAC9766"; + codec->owner = THIS_MODULE; + codec->dai = stac9766_dai; + codec->num_dai = ARRAY_SIZE(stac9766_dai); + codec->write = stac9766_ac97_write; + codec->read = stac9766_ac97_read; + codec->set_bias_level = stac9766_set_bias_level; + INIT_LIST_HEAD(&codec->dapm_widgets); + INIT_LIST_HEAD(&codec->dapm_paths); + + ret = snd_soc_new_ac97_codec(codec, &soc_ac97_ops, 0); + if (ret < 0) + goto codec_err; + + /* register pcms */ + ret = snd_soc_new_pcms(socdev, SNDRV_DEFAULT_IDX1, SNDRV_DEFAULT_STR1); + if (ret < 0) + goto pcm_err; + + /* do a cold reset for the controller and then try + * a warm reset followed by an optional cold reset for codec */ + stac9766_reset(codec, 0); + ret = stac9766_reset(codec, 1); + if (ret < 0) { + printk(KERN_ERR "Failed to reset STAC9766: AC97 link error\n"); + goto reset_err; + } + + stac9766_set_bias_level(codec, SND_SOC_BIAS_STANDBY); + + snd_soc_add_controls(codec, stac9766_snd_ac97_controls, ARRAY_SIZE( + stac9766_snd_ac97_controls)); + + ret = snd_soc_init_card(socdev); + if (ret < 0) + goto reset_err; + return 0; + +reset_err: + snd_soc_free_pcms(socdev); +pcm_err: + snd_soc_free_ac97_codec(codec); +codec_err: + kfree(codec->private_data); +cache_err: + kfree(socdev->card->codec); + socdev->card->codec = NULL; + return ret; +} + +static int stac9766_codec_remove(struct platform_device *pdev) +{ + struct snd_soc_device *socdev = platform_get_drvdata(pdev); + struct snd_soc_codec *codec = socdev->card->codec; + + if (codec == NULL) + return 0; + + snd_soc_free_pcms(socdev); + snd_soc_free_ac97_codec(codec); + kfree(codec->reg_cache); + kfree(codec); + return 0; +} + +struct snd_soc_codec_device soc_codec_dev_stac9766 = +{ + .probe = stac9766_codec_probe, + .remove = stac9766_codec_remove, + .suspend = stac9766_codec_suspend, + .resume = stac9766_codec_resume, +}; +EXPORT_SYMBOL_GPL(soc_codec_dev_stac9766); + +static int __init stac9766_modinit(void) +{ + return snd_soc_register_dais(stac9766_dai, ARRAY_SIZE(stac9766_dai)); +} +module_init(stac9766_modinit); + +static void __exit stac9766_exit(void) +{ + snd_soc_unregister_dais(stac9766_dai, ARRAY_SIZE(stac9766_dai)); +} +module_exit(stac9766_exit); + +MODULE_DESCRIPTION("ASoC stac9766 driver"); +MODULE_AUTHOR("Jon Smirl <jonsmirl(a)gmail.com>"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/stac9766.h b/sound/soc/codecs/stac9766.h new file mode 100644 index 0000000..65642eb --- /dev/null +++ b/sound/soc/codecs/stac9766.h @@ -0,0 +1,21 @@ +/* + * stac9766.h -- STAC9766 Soc Audio driver + */ + +#ifndef _STAC9766_H +#define _STAC9766_H + +#define AC97_STAC_PAGE0 0x1000 +#define AC97_STAC_DA_CONTROL (AC97_STAC_PAGE0 | 0x6A) +#define AC97_STAC_ANALOG_SPECIAL (AC97_STAC_PAGE0 | 0x6E) +#define AC97_STAC_STEREO_MIC 0x78 + +/* STAC9766 DAI ID's */ +#define STAC9766_DAI_AC97_ANALOG 0 +#define STAC9766_DAI_AC97_DIGITAL 1 + +extern struct snd_soc_dai stac9766_dai[]; +extern struct snd_soc_codec_device soc_codec_dev_stac9766; + + +#endif ------------------------------ Message: 3 Date: Sat, 23 May 2009 19:13:09 -0400 From: Jon Smirl <jonsmirl(a)gmail.com> Subject: [alsa-devel] [PATCH V2 7/9] AC97 driver for mpc5200 To: grant.likely(a)secretlab.ca, linuxppc-dev(a)ozlabs.org, alsa-devel(a)alsa-project.org, broonie(a)sirena.org.uk Message-ID: <20090523231309.17919.83073.stgit@terra> Content-Type: text/plain; charset="utf-8" AC97 driver for mpc5200 Signed-off-by: Jon Smirl <jonsmirl(a)gmail.com> --- sound/soc/fsl/Kconfig | 11 + sound/soc/fsl/Makefile | 1 sound/soc/fsl/mpc5200_psc_ac97.c | 394 ++++++++++++++++++++++++++++++++++++++ sound/soc/fsl/mpc5200_psc_ac97.h | 15 + 4 files changed, 421 insertions(+), 0 deletions(-) create mode 100644 sound/soc/fsl/mpc5200_psc_ac97.c create mode 100644 sound/soc/fsl/mpc5200_psc_ac97.h diff --git a/sound/soc/fsl/Kconfig b/sound/soc/fsl/Kconfig index 1918c78..3bce952 100644 --- a/sound/soc/fsl/Kconfig +++ b/sound/soc/fsl/Kconfig @@ -29,3 +29,14 @@ config SND_SOC_MPC5200_I2S select PPC_BESTCOMM_GEN_BD help Say Y here to support the MPC5200 PSCs in I2S mode. + +config SND_SOC_MPC5200_AC97 + tristate "Freescale MPC5200 PSC in AC97 mode driver" + depends on PPC_MPC52xx && PPC_BESTCOMM + select AC97_BUS + select SND_MPC52xx_DMA + select PPC_BESTCOMM_GEN_BD + help + Say Y here to support the MPC5200 PSCs in AC97 mode. + + diff --git a/sound/soc/fsl/Makefile b/sound/soc/fsl/Makefile index 7731ef2..14631a1 100644 --- a/sound/soc/fsl/Makefile +++ b/sound/soc/fsl/Makefile @@ -13,4 +13,5 @@ obj-$(CONFIG_SND_SOC_MPC8610) += snd-soc-fsl-ssi.o snd-soc-fsl-dma.o # MPC5200 Platform Support obj-$(CONFIG_SND_MPC52xx_DMA) += mpc5200_dma.o obj-$(CONFIG_SND_SOC_MPC5200_I2S) += mpc5200_psc_i2s.o +obj-$(CONFIG_SND_SOC_MPC5200_AC97) += mpc5200_psc_ac97.o diff --git a/sound/soc/fsl/mpc5200_psc_ac97.c b/sound/soc/fsl/mpc5200_psc_ac97.c new file mode 100644 index 0000000..fa1bb9a --- /dev/null +++ b/sound/soc/fsl/mpc5200_psc_ac97.c @@ -0,0 +1,394 @@ +/* + * linux/sound/mpc5200-ac97.c -- AC97 support for the Freescale MPC52xx chip. + * + * Copyright (C) 2009 Jon Smirl, Digispeaker + * Author: Jon Smirl <jonsmirl(a)gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/of_platform.h> + +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> + +#include <asm/mpc52xx_psc.h> + +#include "mpc5200_dma.h" +#include "mpc5200_psc_ac97.h" + +#define DRV_NAME "mpc5200-psc-ac97" + +/* ALSA only supports a single AC97 device so static is recommend here */ +static struct psc_dma *psc_dma; + +static unsigned short psc_ac97_read(struct snd_ac97 *ac97, unsigned short reg) +{ + int timeout; + unsigned int val; + + spin_lock(&psc_dma->lock); + + /* Wait for it to be ready */ + timeout = 1000; + while ((--timeout) && (in_be16(&psc_dma->psc_regs->sr_csr.status) & + MPC52xx_PSC_SR_CMDSEND) ) + udelay(10); + + if (!timeout) { + pr_err("timeout on ac97 bus (rdy)\n"); + return 0xffff; + } + + /* Do the read */ + out_be32(&psc_dma->psc_regs->ac97_cmd, (1<<31) | ((reg & 0x7f) << 24)); + + /* Wait for the answer */ + timeout = 1000; + while ((--timeout) && !(in_be16(&psc_dma->psc_regs->sr_csr.status) & + MPC52xx_PSC_SR_DATA_VAL) ) + udelay(10); + + if (!timeout) { + pr_err("timeout on ac97 read (val) %x\n", in_be16(&psc_dma->psc_regs->sr_csr.status)); + return 0xffff; + } + + /* Get the data */ + val = in_be32(&psc_dma->psc_regs->ac97_data); + if ( ((val>>24) & 0x7f) != reg ) { + pr_err("reg echo error on ac97 read\n"); + return 0xffff; + } + val = (val >> 8) & 0xffff; + + spin_unlock(&psc_dma->lock); + return (unsigned short) val; +} + +static void psc_ac97_write(struct snd_ac97 *ac97, unsigned short reg, unsigned short val) +{ + int timeout; + + spin_lock(&psc_dma->lock); + + /* Wait for it to be ready */ + timeout = 1000; + while ((--timeout) && (in_be16(&psc_dma->psc_regs->sr_csr.status) & + MPC52xx_PSC_SR_CMDSEND) ) + udelay(10); + + if (!timeout) { + pr_err("timeout on ac97 write\n"); + return; + } + + /* Write data */ + out_be32(&psc_dma->psc_regs->ac97_cmd, ((reg & 0x7f) << 24) | (val << 8)); + + spin_unlock(&psc_dma->lock); +} + +static void psc_ac97_cold_reset(struct snd_ac97 *ac97) +{ + struct mpc52xx_psc __iomem *regs = psc_dma->psc_regs; + + /* Do a cold reset */ + out_8(&regs->op1, MPC52xx_PSC_OP_RES); + udelay(10); + out_8(&regs->op0, MPC52xx_PSC_OP_RES); + udelay(50); + + /* PSC recover from cold reset (cfr user manual, not sure if useful) */ + out_be32(&regs->sicr, in_be32(&regs->sicr)); +} + +static void psc_ac97_warm_reset(struct snd_ac97 *ac97) +{ + struct mpc52xx_psc __iomem *regs = psc_dma->psc_regs; + + out_be32(&regs->sicr, psc_dma->sicr | MPC52xx_PSC_SICR_AWR); + udelay(3); + out_be32(&regs->sicr, psc_dma->sicr); +} + +struct snd_ac97_bus_ops soc_ac97_ops = { + .read = psc_ac97_read, + .write = psc_ac97_write, + .reset = psc_ac97_cold_reset, + .warm_reset = psc_ac97_warm_reset, +}; +EXPORT_SYMBOL_GPL(soc_ac97_ops); + +#ifdef CONFIG_PM +static int psc_ac97_suspend(struct snd_soc_dai *dai) +{ + return 0; +} + +static int psc_ac97_resume(struct snd_soc_dai *dai) +{ + return 0; +} + +#else +#define psc_ac97_suspend NULL +#define psc_ac97_resume NULL +#endif + +static int psc_ac97_hw_analog_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data; + + dev_dbg(psc_dma->dev, "%s(substream=%p) p_size=%i p_bytes=%i" + " periods=%i buffer_size=%i buffer_bytes=%i channels=%i" + " rate=%i format=%i\n", + __func__, substream, params_period_size(params), + params_period_bytes(params), params_periods(params), + params_buffer_size(params), params_buffer_bytes(params), + params_channels(params), params_rate(params), params_format(params)); + + + if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE) { + if (params_channels(params) == 1) + psc_dma->slots |= 0x00000100; + else + psc_dma->slots |= 0x00000300; + } else { + if (params_channels(params) == 1) + psc_dma->slots |= 0x01000000; + else + psc_dma->slots |= 0x03000000; + } + + spin_lock(&psc_dma->lock); + out_be32(&psc_dma->psc_regs->ac97_slots, psc_dma->slots); + spin_unlock(&psc_dma->lock); + + return 0; +} + +static int psc_ac97_hw_digital_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data; + + spin_lock(&psc_dma->lock); + if (params_channels(params) == 1) + out_be32(&psc_dma->psc_regs->ac97_slots, 0x01000000); + else + out_be32(&psc_dma->psc_regs->ac97_slots, 0x03000000); + spin_unlock(&psc_dma->lock); + + return 0; +} + +static int psc_ac97_trigger(struct snd_pcm_substream *substream, int cmd, + struct snd_soc_dai *dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data; + + switch (cmd) { + case SNDRV_PCM_TRIGGER_STOP: + if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE) + psc_dma->slots &= 0xFFFF0000; + else + psc_dma->slots &= 0x0000FFFF; + + spin_lock(&psc_dma->lock); + out_be32(&psc_dma->psc_regs->ac97_slots, psc_dma->slots); + spin_unlock(&psc_dma->lock); + break; + } + return 0; +} + +/* --------------------------------------------------------------------- + * ALSA SoC Bindings + * + * - Digital Audio Interface (DAI) template + * - create/destroy dai hooks + */ + +/** + * psc_ac97_dai_template: template CPU Digital Audio Interface + */ +static struct snd_soc_dai_ops psc_ac97_analog_ops = { + .hw_params = psc_ac97_hw_analog_params, + .trigger = psc_ac97_trigger, +}; + +static struct snd_soc_dai_ops psc_ac97_digital_ops = { + .hw_params = psc_ac97_hw_digital_params, +}; + +struct snd_soc_dai psc_ac97_dai[] = { +{ + .name = "AC97", + .suspend = psc_ac97_suspend, + .resume = psc_ac97_resume, + .playback = { + .channels_min = 1, + .channels_max = 6, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SNDRV_PCM_FMTBIT_S32_BE, + }, + .capture = { + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SNDRV_PCM_FMTBIT_S32_BE, + }, + .ops = &psc_ac97_analog_ops, +}, +{ + .name = "SPDIF", + .playback = { + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_32000 | \ + SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000, + .formats = SNDRV_PCM_FMTBIT_IEC958_SUBFRAME_BE, + }, + .ops = &psc_ac97_digital_ops, +}}; +EXPORT_SYMBOL_GPL(psc_ac97_dai); + + + +/* --------------------------------------------------------------------- + * OF platform bus binding code: + * - Probe/remove operations + * - OF device match table + */ +static int __devinit psc_ac97_of_probe(struct of_device *op, + const struct of_device_id *match) +{ + int rc, i, id1, id2, timeout, max_reset; + struct snd_ac97 ac97; + struct mpc52xx_psc __iomem *regs; + + rc = mpc5200_audio_dma_create(op); + if (rc != 0) + return rc; + + for (i = 0; i < ARRAY_SIZE(psc_ac97_dai); i++) + psc_ac97_dai[i].dev = &op->dev; + + rc = snd_soc_register_dais(psc_ac97_dai, ARRAY_SIZE(psc_ac97_dai)); + if (rc != 0) { + pr_err("Failed to register DAI\n"); + return 0; + } + + psc_dma = dev_get_drvdata(&op->dev); + regs = psc_dma->psc_regs; + ac97.private_data = psc_dma; + + for (i = 0; i < ARRAY_SIZE(psc_ac97_dai); i++) + psc_ac97_dai[i].private_data = psc_dma; + + psc_dma->imr = 0; + out_be16(&psc_dma->psc_regs->isr_imr.imr, psc_dma->imr); + + /* Configure the serial interface mode to AC97 */ + psc_dma->sicr = MPC52xx_PSC_SICR_SIM_AC97 | MPC52xx_PSC_SICR_ENAC97; + out_be32(&regs->sicr, psc_dma->sicr); + + /* No slots active */ + out_be32(&regs->ac97_slots, 0x00000000); + + /* AC97 clock is generated by the codec. + * Ensure that it starts ticking after codec reset. + */ + max_reset = 0; +reset: + if (max_reset++ > 5) { + dev_err(&op->dev, "AC97 codec failed to reset\n"); + mpc5200_audio_dma_destroy(op); + return -ENODEV; + } + + psc_ac97_cold_reset(&ac97); + psc_ac97_warm_reset(&ac97); + + /* first make sure it is low */ + timeout = 0; + while ((in_8(&regs->ipcr_acr.ipcr) & 0x80) != 0) { + udelay(1); + if (timeout++ > 1000) + goto reset; + } + /* then wait for the transition to high */ + timeout = 0; + while ((in_8(&regs->ipcr_acr.ipcr) & 0x80) == 0) { + udelay(1); + if (timeout++ > 1000) + psc_ac97_warm_reset(&ac97); + } + + /* Go */ + out_8(&regs->command, MPC52xx_PSC_TX_ENABLE | MPC52xx_PSC_RX_ENABLE); + + id1 = psc_ac97_read(&ac97, AC97_VENDOR_ID1); + id2 = psc_ac97_read(&ac97, AC97_VENDOR_ID2); + + dev_info(&op->dev, "Codec ID is %04x %04x\n", id1, id2); + + return 0; +} + +static int __devexit psc_ac97_of_remove(struct of_device *op) +{ + return mpc5200_audio_dma_destroy(op); +} + +/* Match table for of_platform binding */ +static struct of_device_id psc_ac97_match[] __devinitdata = { + { .compatible = "fsl,mpc5200-psc-ac97", }, + { .compatible = "fsl,mpc5200b-psc-ac97", }, + {} +}; +MODULE_DEVICE_TABLE(of, psc_ac97_match); + +static struct of_platform_driver psc_ac97_driver = { + .match_table = psc_ac97_match, + .probe = psc_ac97_of_probe, + .remove = __devexit_p(psc_ac97_of_remove), + .driver = { + .name = "mpc5200-psc-ac97", + .owner = THIS_MODULE, + }, +}; + +/* --------------------------------------------------------------------- + * Module setup and teardown; simply register the of_platform driver + * for the PSC in AC97 mode. + */ +static int __init psc_ac97_init(void) +{ + return of_register_platform_driver(&psc_ac97_driver); +} +module_init(psc_ac97_init); + +static void __exit psc_ac97_exit(void) +{ + of_unregister_platform_driver(&psc_ac97_driver); +} +module_exit(psc_ac97_exit); + +MODULE_AUTHOR("Jon Smirl <jonsmirl(a)gmail.com>"); +MODULE_DESCRIPTION("mpc5200 AC97 module"); +MODULE_LICENSE("GPL"); + diff --git a/sound/soc/fsl/mpc5200_psc_ac97.h b/sound/soc/fsl/mpc5200_psc_ac97.h new file mode 100644 index 0000000..4bc18c3 --- /dev/null +++ b/sound/soc/fsl/mpc5200_psc_ac97.h @@ -0,0 +1,15 @@ +/* + * Freescale MPC5200 PSC in AC97 mode + * ALSA SoC Digital Audio Interface (DAI) driver + * + */ + +#ifndef __SOUND_SOC_FSL_MPC52xx_PSC_AC97_H__ +#define __SOUND_SOC_FSL_MPC52xx_PSC_AC97_H__ + +extern struct snd_soc_dai psc_ac97_dai[]; + +#define MPC5200_AC97_NORMAL 0 +#define MPC5200_AC97_SPDIF 1 + +#endif /* __SOUND_SOC_FSL_MPC52xx_PSC_AC97_H__ */ ------------------------------ _______________________________________________ Alsa-devel mailing list Alsa-devel(a)alsa-project.org http://mailman.alsa-project.org/mailman/listinfo/alsa-devel End of Alsa-devel Digest, Vol 27, Issue 124 *******************************************

1 0

Re: [alsa-devel] Alsa-devel Digest, Vol 27, Issue 124
by Demian Martin 24 May '09

24 May '09

Demian Martin PDS 209 613 6990 -----Original Message----- From: alsa-devel-request(a)alsa-project.org Date: Sun, 24 May 2009 01:13:19 To: <alsa-devel(a)alsa-project.org> Subject: Alsa-devel Digest, Vol 27, Issue 124 Send Alsa-devel mailing list submissions to alsa-devel(a)alsa-project.org To subscribe or unsubscribe via the World Wide Web, visit http://mailman.alsa-project.org/mailman/listinfo/alsa-devel or, via email, send a message with subject or body 'help' to alsa-devel-request(a)alsa-project.org You can reach the person managing the list at alsa-devel-owner(a)alsa-project.org When replying, please edit your Subject line so it is more specific than "Re: Contents of Alsa-devel digest..." Today's Topics: 1. [PATCH V2 4/9] Add a few more mpc5200 PSC defines (Jon Smirl) 2. [PATCH V2 6/9] Codec for STAC9766 used on the Efika (Jon Smirl) 3. [PATCH V2 7/9] AC97 driver for mpc5200 (Jon Smirl) ---------------------------------------------------------------------- Message: 1 Date: Sat, 23 May 2009 19:13:03 -0400 From: Jon Smirl <jonsmirl(a)gmail.com> Subject: [alsa-devel] [PATCH V2 4/9] Add a few more mpc5200 PSC defines To: grant.likely(a)secretlab.ca, linuxppc-dev(a)ozlabs.org, alsa-devel(a)alsa-project.org, broonie(a)sirena.org.uk Message-ID: <20090523231303.17919.35877.stgit@terra> Content-Type: text/plain; charset="utf-8" Add a few more mpc5200 PSC defines. More bit fields defines for mpc5200 PSC registers. This patch is going in via Grant's tree. Signed-off-by: Jon Smirl <jonsmirl(a)gmail.com> --- 0 files changed, 0 insertions(+), 0 deletions(-) diff --git a/arch/powerpc/include/asm/mpc52xx_psc.h b/arch/powerpc/include/asm/mpc52xx_psc.h index a218da6..fb84120 100644 --- a/arch/powerpc/include/asm/mpc52xx_psc.h +++ b/arch/powerpc/include/asm/mpc52xx_psc.h @@ -28,6 +28,10 @@ #define MPC52xx_PSC_MAXNUM 6 /* Programmable Serial Controller (PSC) status register bits */ +#define MPC52xx_PSC_SR_UNEX_RX 0x0001 +#define MPC52xx_PSC_SR_DATA_VAL 0x0002 +#define MPC52xx_PSC_SR_DATA_OVR 0x0004 +#define MPC52xx_PSC_SR_CMDSEND 0x0008 #define MPC52xx_PSC_SR_CDE 0x0080 #define MPC52xx_PSC_SR_RXRDY 0x0100 #define MPC52xx_PSC_SR_RXFULL 0x0200 @@ -61,6 +65,12 @@ #define MPC52xx_PSC_RXTX_FIFO_EMPTY 0x0001 /* PSC interrupt status/mask bits */ +#define MPC52xx_PSC_IMR_UNEX_RX_SLOT 0x0001 +#define MPC52xx_PSC_IMR_DATA_VALID 0x0002 +#define MPC52xx_PSC_IMR_DATA_OVR 0x0004 +#define MPC52xx_PSC_IMR_CMD_SEND 0x0008 +#define MPC52xx_PSC_IMR_ERROR 0x0040 +#define MPC52xx_PSC_IMR_DEOF 0x0080 #define MPC52xx_PSC_IMR_TXRDY 0x0100 #define MPC52xx_PSC_IMR_RXRDY 0x0200 #define MPC52xx_PSC_IMR_DB 0x0400 @@ -117,6 +127,7 @@ #define MPC52xx_PSC_SICR_SIM_FIR (0x6 << 24) #define MPC52xx_PSC_SICR_SIM_CODEC_24 (0x7 << 24) #define MPC52xx_PSC_SICR_SIM_CODEC_32 (0xf << 24) +#define MPC52xx_PSC_SICR_AWR (1 << 30) #define MPC52xx_PSC_SICR_GENCLK (1 << 23) #define MPC52xx_PSC_SICR_I2S (1 << 22) #define MPC52xx_PSC_SICR_CLKPOL (1 << 21) ------------------------------ Message: 2 Date: Sat, 23 May 2009 19:13:07 -0400 From: Jon Smirl <jonsmirl(a)gmail.com> Subject: [alsa-devel] [PATCH V2 6/9] Codec for STAC9766 used on the Efika To: grant.likely(a)secretlab.ca, linuxppc-dev(a)ozlabs.org, alsa-devel(a)alsa-project.org, broonie(a)sirena.org.uk Message-ID: <20090523231307.17919.5277.stgit@terra> Content-Type: text/plain; charset="utf-8" AC97 codec for STAC9766 used on the Efika. Datasheet: http://www.idt.com/products/getDoc.cfm?docID=13134007 Signed-off-by: Jon Smirl <jonsmirl(a)gmail.com> --- 0 files changed, 0 insertions(+), 0 deletions(-) diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 7f78b65..cb07d9b 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -19,6 +19,7 @@ config SND_SOC_ALL_CODECS select SND_SOC_CS4270 if I2C select SND_SOC_PCM3008 select SND_SOC_SSM2602 if I2C + select SND_SOC_STAC9766 if SND_SOC_AC97_BUS select SND_SOC_TLV320AIC23 if I2C select SND_SOC_TLV320AIC26 if SPI_MASTER select SND_SOC_TLV320AIC3X if I2C @@ -93,6 +94,9 @@ config SND_SOC_PCM3008 config SND_SOC_SSM2602 tristate +config SND_SOC_STAC9766 + tristate + config SND_SOC_TLV320AIC23 tristate diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 70c55fa..46c007c 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -7,6 +7,7 @@ snd-soc-cs4270-objs := cs4270.o snd-soc-l3-objs := l3.o snd-soc-pcm3008-objs := pcm3008.o snd-soc-ssm2602-objs := ssm2602.o +snd-soc-stac9766-objs := stac9766.o snd-soc-tlv320aic23-objs := tlv320aic23.o snd-soc-tlv320aic26-objs := tlv320aic26.o snd-soc-tlv320aic3x-objs := tlv320aic3x.o @@ -42,6 +43,7 @@ obj-$(CONFIG_SND_SOC_CS4270) += snd-soc-cs4270.o obj-$(CONFIG_SND_SOC_L3) += snd-soc-l3.o obj-$(CONFIG_SND_SOC_PCM3008) += snd-soc-pcm3008.o obj-$(CONFIG_SND_SOC_SSM2602) += snd-soc-ssm2602.o +obj-$(CONFIG_SND_SOC_STAC9766) += snd-soc-stac9766.o obj-$(CONFIG_SND_SOC_TLV320AIC23) += snd-soc-tlv320aic23.o obj-$(CONFIG_SND_SOC_TLV320AIC26) += snd-soc-tlv320aic26.o obj-$(CONFIG_SND_SOC_TLV320AIC3X) += snd-soc-tlv320aic3x.o diff --git a/sound/soc/codecs/stac9766.c b/sound/soc/codecs/stac9766.c new file mode 100644 index 0000000..7740cd5 --- /dev/null +++ b/sound/soc/codecs/stac9766.c @@ -0,0 +1,470 @@ +/* + * stac9766.c -- ALSA SoC STAC9766 codec support + * + * Copyright 2009 Jon Smirl, Digispeaker + * Author: Jon Smirl <jonsmirl(a)gmail.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * Features:- + * + * o Support for AC97 Codec, S/PDIF + */ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/device.h> +#include <sound/core.h> +#include <sound/pcm.h> +#include <sound/ac97_codec.h> +#include <sound/initval.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/tlv.h> +#include <sound/soc-of-simple.h> + +#include "stac9766.h" + +#define STAC9766_VERSION "0.10" + +/* + * STAC9766 register cache + */ +static const u16 stac9766_reg[] = { + 0x6A90, 0x8000, 0x8000, 0x8000, /* 6 */ + 0x0000, 0x0000, 0x8008, 0x8008, /* e */ + 0x8808, 0x8808, 0x8808, 0x8808, /* 16 */ + 0x8808, 0x0000, 0x8000, 0x0000, /* 1e */ + 0x0000, 0x0000, 0x0000, 0x000f, /* 26 */ + 0x0a05, 0x0400, 0xbb80, 0x0000, /* 2e */ + 0x0000, 0xbb80, 0x0000, 0x0000, /* 36 */ + 0x0000, 0x2000, 0x0000, 0x0100, /* 3e */ + 0x0000, 0x0000, 0x0080, 0x0000, /* 46 */ + 0x0000, 0x0000, 0x0003, 0xffff, /* 4e */ + 0x0000, 0x0000, 0x0000, 0x0000, /* 56 */ + 0x4000, 0x0000, 0x0000, 0x0000, /* 5e */ + 0x1201, 0xFFFF, 0xFFFF, 0x0000, /* 66 */ + 0x0000, 0x0000, 0x0000, 0x0000, /* 6e */ + 0x0000, 0x0000, 0x0000, 0x0006, /* 76 */ + 0x0000, 0x0000, 0x0000, 0x0000, /* 7e */ +}; + +static const char *stac9766_record_mux[] = {"Mic", "CD", "Video", "AUX", "Line", "Stereo Mix", "Mono Mix", "Phone"}; +static const char *stac9766_mono_mux[] = {"Mix", "Mic"}; +static const char *stac9766_mic_mux[] = {"Mic1", "Mic2"}; +static const char *stac9766_SPDIF_mux[] = {"PCM", "ADC Record"}; +static const char *stac9766_popbypass_mux[] = {"Normal", "Bypass Mixer"}; +static const char *stac9766_record_all_mux[] = {"All analog", "Analog plus DAC"}; +static const char *stac9766_boost1[] = {"0dB", "10dB"}; +static const char *stac9766_boost2[] = {"0dB", "20dB"}; +static const char *stac9766_stereo_mic[] = {"Off", "On"}; + +static const struct soc_enum stac9766_record_enum = + SOC_ENUM_DOUBLE(AC97_REC_SEL, 8, 0, 8, stac9766_record_mux); +static const struct soc_enum stac9766_mono_enum = + SOC_ENUM_SINGLE(AC97_GENERAL_PURPOSE, 9, 2, stac9766_mono_mux); +static const struct soc_enum stac9766_mic_enum = + SOC_ENUM_SINGLE(AC97_GENERAL_PURPOSE, 8, 2, stac9766_mic_mux); +static const struct soc_enum stac9766_SPDIF_enum = + SOC_ENUM_SINGLE(AC97_STAC_DA_CONTROL, 1, 2, stac9766_SPDIF_mux); +static const struct soc_enum stac9766_popbypass_enum = + SOC_ENUM_SINGLE(AC97_GENERAL_PURPOSE, 15, 2, stac9766_popbypass_mux); +static const struct soc_enum stac9766_record_all_enum = + SOC_ENUM_SINGLE(AC97_STAC_ANALOG_SPECIAL, 12, 2, stac9766_record_all_mux); +static const struct soc_enum stac9766_boost1_enum = + SOC_ENUM_SINGLE(AC97_MIC, 6, 2, stac9766_boost1); /* 0/10dB */ +static const struct soc_enum stac9766_boost2_enum = + SOC_ENUM_SINGLE(AC97_STAC_ANALOG_SPECIAL, 2, 2, stac9766_boost2); /* 0/20dB */ +static const struct soc_enum stac9766_stereo_mic_enum = + SOC_ENUM_SINGLE(AC97_STAC_STEREO_MIC, 2, 1, stac9766_stereo_mic); + +static const DECLARE_TLV_DB_LINEAR(master_tlv, -4600, 0); +static const DECLARE_TLV_DB_LINEAR(record_tlv, 0, 2250); +static const DECLARE_TLV_DB_LINEAR(beep_tlv, -4500, 0); +static const DECLARE_TLV_DB_LINEAR(mix_tlv, -3450, 1200); + +static const struct snd_kcontrol_new stac9766_snd_ac97_controls[] = { + SOC_DOUBLE_TLV("Speaker Volume", AC97_MASTER, 8, 0, 31, 1, master_tlv), + SOC_SINGLE("Speaker Switch", AC97_MASTER, 15, 1, 1), + SOC_DOUBLE_TLV("Headphone Volume", AC97_HEADPHONE, 8, 0, 31, 1, master_tlv), + SOC_SINGLE("Headphone Switch", AC97_HEADPHONE, 15, 1, 1), + SOC_SINGLE_TLV("Mono Out Volume", AC97_MASTER_MONO, 0, 31, 1, master_tlv), + SOC_SINGLE("Mono Out Switch", AC97_MASTER_MONO, 15, 1, 1), + + SOC_DOUBLE_TLV("Record Volume", AC97_REC_GAIN, 8, 0, 15, 0, record_tlv), + SOC_SINGLE("Record Switch", AC97_REC_GAIN, 15, 1, 1), + + + SOC_SINGLE_TLV("Beep Volume", AC97_PC_BEEP, 1, 15, 1, beep_tlv), + SOC_SINGLE("Beep Switch", AC97_PC_BEEP, 15, 1, 1), + SOC_SINGLE("Beep Frequency", AC97_PC_BEEP, 5, 127, 1), + SOC_SINGLE_TLV("Phone Volume", AC97_PHONE, 0, 31, 1, mix_tlv), + SOC_SINGLE("Phone Switch", AC97_PHONE, 15, 1, 1), + + SOC_ENUM("Mic Boost1", stac9766_boost1_enum), + SOC_ENUM("Mic Boost2", stac9766_boost2_enum), + SOC_SINGLE_TLV("Mic Volume", AC97_MIC, 0, 31, 1, mix_tlv), + SOC_SINGLE("Mic Switch", AC97_MIC, 15, 1, 1), + SOC_ENUM("Stereo Mic", stac9766_stereo_mic_enum), + + SOC_DOUBLE_TLV("Line Volume", AC97_LINE, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("Line Switch", AC97_LINE, 15, 1, 1), + SOC_DOUBLE_TLV("CD Volume", AC97_CD, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("CD Switch", AC97_CD, 15, 1, 1), + SOC_DOUBLE_TLV("AUX Volume", AC97_AUX, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("AUX Switch", AC97_AUX, 15, 1, 1), + SOC_DOUBLE_TLV("Video Volume", AC97_VIDEO, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("Video Switch", AC97_VIDEO, 15, 1, 1), + + SOC_DOUBLE_TLV("DAC Volume", AC97_PCM, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("DAC Switch", AC97_PCM, 15, 1, 1), + SOC_SINGLE("Loopback Test Switch", AC97_GENERAL_PURPOSE, 7, 1, 0), + SOC_SINGLE("3D Volume", AC97_3D_CONTROL, 3, 2, 1), + SOC_SINGLE("3D Switch", AC97_GENERAL_PURPOSE, 13, 1, 0), + + SOC_ENUM("SPDIF Mux", stac9766_SPDIF_enum), + SOC_ENUM("Mic1/2 Mux", stac9766_mic_enum), + SOC_ENUM("Record All Mux", stac9766_record_all_enum), + SOC_ENUM("Record Mux", stac9766_record_enum), + SOC_ENUM("Mono Mux", stac9766_mono_enum), + SOC_ENUM("Pop Bypass Mux", stac9766_popbypass_enum), +}; + +int stac9766_ac97_write(struct snd_soc_codec *codec, unsigned int reg, + unsigned int val) +{ + u16 *cache = codec->reg_cache; + + if (reg > AC97_STAC_PAGE0) { + stac9766_ac97_write(codec, AC97_INT_PAGING, 0); + soc_ac97_ops.write(codec->ac97, reg, val); + stac9766_ac97_write(codec, AC97_INT_PAGING, 1); + return 0; + } + if (reg / 2 > ARRAY_SIZE(stac9766_reg)) + return -EIO; + + soc_ac97_ops.write(codec->ac97, reg, val); + cache[reg / 2] = val; + return 0; +} + +unsigned int stac9766_ac97_read(struct snd_soc_codec *codec, unsigned int reg) +{ + u16 val = 0, *cache = codec->reg_cache; + + if (reg > AC97_STAC_PAGE0) { + stac9766_ac97_write(codec, AC97_INT_PAGING, 0); + val = soc_ac97_ops.read(codec->ac97, reg - AC97_STAC_PAGE0); + stac9766_ac97_write(codec, AC97_INT_PAGING, 1); + return val; + } + if (reg / 2 > ARRAY_SIZE(stac9766_reg)) + return -EIO; + + if (reg == AC97_RESET || reg == AC97_GPIO_STATUS || + reg == AC97_INT_PAGING || reg == AC97_VENDOR_ID1 || + reg == AC97_VENDOR_ID2) { + + val = soc_ac97_ops.read(codec->ac97, reg); + return val; + } + return cache[reg / 2]; +} + +static int ac97_analog_prepare(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct snd_soc_codec *codec = dai->codec; + struct snd_pcm_runtime *runtime = substream->runtime; + unsigned short reg, vra; + + vra = stac9766_ac97_read(codec, AC97_EXTENDED_STATUS); + + vra |= 0x1; /* enable variable rate audio */ + + stac9766_ac97_write(codec, AC97_EXTENDED_STATUS, vra); + + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) + reg = AC97_PCM_FRONT_DAC_RATE; + else + reg = AC97_PCM_LR_ADC_RATE; + + return stac9766_ac97_write(codec, reg, runtime->rate); +} + +static int ac97_digital_prepare(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct snd_soc_codec *codec = dai->codec; + struct snd_pcm_runtime *runtime = substream->runtime; + unsigned short reg, vra; + + stac9766_ac97_write(codec, AC97_SPDIF, 0x2002); + + vra = stac9766_ac97_read(codec, AC97_EXTENDED_STATUS); + vra |= 0x5; /* Enable VRA and SPDIF out */ + + stac9766_ac97_write(codec, AC97_EXTENDED_STATUS, vra); + + reg = AC97_PCM_FRONT_DAC_RATE; + + return stac9766_ac97_write(codec, reg, runtime->rate); +} + +static int ac97_digital_trigger(struct snd_pcm_substream *substream, + int cmd, struct snd_soc_dai *dai) +{ + struct snd_soc_codec *codec = dai->codec; + unsigned short vra; + + switch (cmd) { + case SNDRV_PCM_TRIGGER_STOP: + vra = stac9766_ac97_read(codec, AC97_EXTENDED_STATUS); + vra &= !0x04; + stac9766_ac97_write(codec, AC97_EXTENDED_STATUS, vra); + break; + } + return 0; +} + +static int stac9766_set_bias_level(struct snd_soc_codec *codec, + enum snd_soc_bias_level level) +{ + switch (level) { + case SND_SOC_BIAS_ON: /* full On */ + case SND_SOC_BIAS_PREPARE: /* partial On */ + case SND_SOC_BIAS_STANDBY: /* Off, with power */ + stac9766_ac97_write(codec, AC97_POWERDOWN, 0x0000); + break; + case SND_SOC_BIAS_OFF: /* Off, without power */ + /* disable everything including AC link */ + stac9766_ac97_write(codec, AC97_POWERDOWN, 0xffff); + break; + } + codec->bias_level = level; + return 0; +} + +int stac9766_reset(struct snd_soc_codec *codec, int try_warm) +{ + if (try_warm && soc_ac97_ops.warm_reset) { + soc_ac97_ops.warm_reset(codec->ac97); + if (stac9766_ac97_read(codec, 0) == stac9766_reg[0]) + return 1; + } + + soc_ac97_ops.reset(codec->ac97); + if (soc_ac97_ops.warm_reset) + soc_ac97_ops.warm_reset(codec->ac97); + if (stac9766_ac97_read(codec, 0) != stac9766_reg[0]) + return -EIO; + return 0; +} + +static int stac9766_codec_suspend(struct platform_device *pdev, + pm_message_t state) +{ + struct snd_soc_device *socdev = platform_get_drvdata(pdev); + struct snd_soc_codec *codec = socdev->card->codec; + + stac9766_set_bias_level(codec, SND_SOC_BIAS_OFF); + return 0; +} + +static int stac9766_codec_resume(struct platform_device *pdev) +{ + struct snd_soc_device *socdev = platform_get_drvdata(pdev); + struct snd_soc_codec *codec = socdev->card->codec; + u16 id, reset; + + reset = 0; + /* give the codec an AC97 warm reset to start the link */ +reset: + if (reset > 5) { + printk(KERN_ERR "stac9766 failed to resume"); + return -EIO; + } + codec->ac97->bus->ops->warm_reset(codec->ac97); + id = soc_ac97_ops.read(codec->ac97, AC97_VENDOR_ID2); + if (id != 0x4c13) { + stac9766_reset(codec, 0); + reset++; + goto reset; + } + stac9766_set_bias_level(codec, SND_SOC_BIAS_STANDBY); + + if (codec->suspend_bias_level == SND_SOC_BIAS_ON) + stac9766_set_bias_level(codec, SND_SOC_BIAS_ON); + + return 0; +} + +static struct snd_soc_dai_ops stac9766_dai_ops_analog = +{ + .prepare = ac97_analog_prepare, +}; + +static struct snd_soc_dai_ops stac9766_dai_ops_digital = +{ + .prepare = ac97_digital_prepare, + .trigger = ac97_digital_trigger, +}; + +struct snd_soc_dai stac9766_dai[] = { +{ + .name = "stac9766 analog", + .id = 0, + .ac97_control = 1, + + /* stream cababilities */ + .playback = { + .stream_name = "stac9766 analog", + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SND_SOC_STD_AC97_FMTS, + }, + .capture = { + .stream_name = "stac9766 analog", + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SND_SOC_STD_AC97_FMTS, + }, + /* alsa ops */ + .ops = &stac9766_dai_ops_analog, +}, +{ + .name = "stac9766 IEC958", + .id = 1, + .ac97_control = 1, + + /* stream cababilities */ + .playback = { + .stream_name = "stac9766 IEC958", + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_32000 | \ + SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000, + .formats = SNDRV_PCM_FORMAT_IEC958_SUBFRAME_BE, + }, + /* alsa ops */ + .ops = &stac9766_dai_ops_digital, +}}; +EXPORT_SYMBOL_GPL(stac9766_dai); + +static int stac9766_codec_probe(struct platform_device *pdev) +{ + struct snd_soc_device *socdev = platform_get_drvdata(pdev); + struct snd_soc_codec *codec; + int ret = 0; + + printk(KERN_INFO "STAC9766 SoC Audio Codec %s\n", STAC9766_VERSION); + + socdev->card->codec = kzalloc(sizeof(struct snd_soc_codec), GFP_KERNEL); + if (socdev->card->codec == NULL) + return -ENOMEM; + codec = socdev->card->codec; + mutex_init(&codec->mutex); + + codec->reg_cache = kmemdup(stac9766_reg, sizeof(stac9766_reg), GFP_KERNEL); + if (codec->reg_cache == NULL) { + ret = -ENOMEM; + goto cache_err; + } + codec->reg_cache_size = sizeof(stac9766_reg); + codec->reg_cache_step = 2; + + codec->name = "STAC9766"; + codec->owner = THIS_MODULE; + codec->dai = stac9766_dai; + codec->num_dai = ARRAY_SIZE(stac9766_dai); + codec->write = stac9766_ac97_write; + codec->read = stac9766_ac97_read; + codec->set_bias_level = stac9766_set_bias_level; + INIT_LIST_HEAD(&codec->dapm_widgets); + INIT_LIST_HEAD(&codec->dapm_paths); + + ret = snd_soc_new_ac97_codec(codec, &soc_ac97_ops, 0); + if (ret < 0) + goto codec_err; + + /* register pcms */ + ret = snd_soc_new_pcms(socdev, SNDRV_DEFAULT_IDX1, SNDRV_DEFAULT_STR1); + if (ret < 0) + goto pcm_err; + + /* do a cold reset for the controller and then try + * a warm reset followed by an optional cold reset for codec */ + stac9766_reset(codec, 0); + ret = stac9766_reset(codec, 1); + if (ret < 0) { + printk(KERN_ERR "Failed to reset STAC9766: AC97 link error\n"); + goto reset_err; + } + + stac9766_set_bias_level(codec, SND_SOC_BIAS_STANDBY); + + snd_soc_add_controls(codec, stac9766_snd_ac97_controls, ARRAY_SIZE( + stac9766_snd_ac97_controls)); + + ret = snd_soc_init_card(socdev); + if (ret < 0) + goto reset_err; + return 0; + +reset_err: + snd_soc_free_pcms(socdev); +pcm_err: + snd_soc_free_ac97_codec(codec); +codec_err: + kfree(codec->private_data); +cache_err: + kfree(socdev->card->codec); + socdev->card->codec = NULL; + return ret; +} + +static int stac9766_codec_remove(struct platform_device *pdev) +{ + struct snd_soc_device *socdev = platform_get_drvdata(pdev); + struct snd_soc_codec *codec = socdev->card->codec; + + if (codec == NULL) + return 0; + + snd_soc_free_pcms(socdev); + snd_soc_free_ac97_codec(codec); + kfree(codec->reg_cache); + kfree(codec); + return 0; +} + +struct snd_soc_codec_device soc_codec_dev_stac9766 = +{ + .probe = stac9766_codec_probe, + .remove = stac9766_codec_remove, + .suspend = stac9766_codec_suspend, + .resume = stac9766_codec_resume, +}; +EXPORT_SYMBOL_GPL(soc_codec_dev_stac9766); + +static int __init stac9766_modinit(void) +{ + return snd_soc_register_dais(stac9766_dai, ARRAY_SIZE(stac9766_dai)); +} +module_init(stac9766_modinit); + +static void __exit stac9766_exit(void) +{ + snd_soc_unregister_dais(stac9766_dai, ARRAY_SIZE(stac9766_dai)); +} +module_exit(stac9766_exit); + +MODULE_DESCRIPTION("ASoC stac9766 driver"); +MODULE_AUTHOR("Jon Smirl <jonsmirl(a)gmail.com>"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/stac9766.h b/sound/soc/codecs/stac9766.h new file mode 100644 index 0000000..65642eb --- /dev/null +++ b/sound/soc/codecs/stac9766.h @@ -0,0 +1,21 @@ +/* + * stac9766.h -- STAC9766 Soc Audio driver + */ + +#ifndef _STAC9766_H +#define _STAC9766_H + +#define AC97_STAC_PAGE0 0x1000 +#define AC97_STAC_DA_CONTROL (AC97_STAC_PAGE0 | 0x6A) +#define AC97_STAC_ANALOG_SPECIAL (AC97_STAC_PAGE0 | 0x6E) +#define AC97_STAC_STEREO_MIC 0x78 + +/* STAC9766 DAI ID's */ +#define STAC9766_DAI_AC97_ANALOG 0 +#define STAC9766_DAI_AC97_DIGITAL 1 + +extern struct snd_soc_dai stac9766_dai[]; +extern struct snd_soc_codec_device soc_codec_dev_stac9766; + + +#endif ------------------------------ Message: 3 Date: Sat, 23 May 2009 19:13:09 -0400 From: Jon Smirl <jonsmirl(a)gmail.com> Subject: [alsa-devel] [PATCH V2 7/9] AC97 driver for mpc5200 To: grant.likely(a)secretlab.ca, linuxppc-dev(a)ozlabs.org, alsa-devel(a)alsa-project.org, broonie(a)sirena.org.uk Message-ID: <20090523231309.17919.83073.stgit@terra> Content-Type: text/plain; charset="utf-8" AC97 driver for mpc5200 Signed-off-by: Jon Smirl <jonsmirl(a)gmail.com> --- sound/soc/fsl/Kconfig | 11 + sound/soc/fsl/Makefile | 1 sound/soc/fsl/mpc5200_psc_ac97.c | 394 ++++++++++++++++++++++++++++++++++++++ sound/soc/fsl/mpc5200_psc_ac97.h | 15 + 4 files changed, 421 insertions(+), 0 deletions(-) create mode 100644 sound/soc/fsl/mpc5200_psc_ac97.c create mode 100644 sound/soc/fsl/mpc5200_psc_ac97.h diff --git a/sound/soc/fsl/Kconfig b/sound/soc/fsl/Kconfig index 1918c78..3bce952 100644 --- a/sound/soc/fsl/Kconfig +++ b/sound/soc/fsl/Kconfig @@ -29,3 +29,14 @@ config SND_SOC_MPC5200_I2S select PPC_BESTCOMM_GEN_BD help Say Y here to support the MPC5200 PSCs in I2S mode. + +config SND_SOC_MPC5200_AC97 + tristate "Freescale MPC5200 PSC in AC97 mode driver" + depends on PPC_MPC52xx && PPC_BESTCOMM + select AC97_BUS + select SND_MPC52xx_DMA + select PPC_BESTCOMM_GEN_BD + help + Say Y here to support the MPC5200 PSCs in AC97 mode. + + diff --git a/sound/soc/fsl/Makefile b/sound/soc/fsl/Makefile index 7731ef2..14631a1 100644 --- a/sound/soc/fsl/Makefile +++ b/sound/soc/fsl/Makefile @@ -13,4 +13,5 @@ obj-$(CONFIG_SND_SOC_MPC8610) += snd-soc-fsl-ssi.o snd-soc-fsl-dma.o # MPC5200 Platform Support obj-$(CONFIG_SND_MPC52xx_DMA) += mpc5200_dma.o obj-$(CONFIG_SND_SOC_MPC5200_I2S) += mpc5200_psc_i2s.o +obj-$(CONFIG_SND_SOC_MPC5200_AC97) += mpc5200_psc_ac97.o diff --git a/sound/soc/fsl/mpc5200_psc_ac97.c b/sound/soc/fsl/mpc5200_psc_ac97.c new file mode 100644 index 0000000..fa1bb9a --- /dev/null +++ b/sound/soc/fsl/mpc5200_psc_ac97.c @@ -0,0 +1,394 @@ +/* + * linux/sound/mpc5200-ac97.c -- AC97 support for the Freescale MPC52xx chip. + * + * Copyright (C) 2009 Jon Smirl, Digispeaker + * Author: Jon Smirl <jonsmirl(a)gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/of_platform.h> + +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> + +#include <asm/mpc52xx_psc.h> + +#include "mpc5200_dma.h" +#include "mpc5200_psc_ac97.h" + +#define DRV_NAME "mpc5200-psc-ac97" + +/* ALSA only supports a single AC97 device so static is recommend here */ +static struct psc_dma *psc_dma; + +static unsigned short psc_ac97_read(struct snd_ac97 *ac97, unsigned short reg) +{ + int timeout; + unsigned int val; + + spin_lock(&psc_dma->lock); + + /* Wait for it to be ready */ + timeout = 1000; + while ((--timeout) && (in_be16(&psc_dma->psc_regs->sr_csr.status) & + MPC52xx_PSC_SR_CMDSEND) ) + udelay(10); + + if (!timeout) { + pr_err("timeout on ac97 bus (rdy)\n"); + return 0xffff; + } + + /* Do the read */ + out_be32(&psc_dma->psc_regs->ac97_cmd, (1<<31) | ((reg & 0x7f) << 24)); + + /* Wait for the answer */ + timeout = 1000; + while ((--timeout) && !(in_be16(&psc_dma->psc_regs->sr_csr.status) & + MPC52xx_PSC_SR_DATA_VAL) ) + udelay(10); + + if (!timeout) { + pr_err("timeout on ac97 read (val) %x\n", in_be16(&psc_dma->psc_regs->sr_csr.status)); + return 0xffff; + } + + /* Get the data */ + val = in_be32(&psc_dma->psc_regs->ac97_data); + if ( ((val>>24) & 0x7f) != reg ) { + pr_err("reg echo error on ac97 read\n"); + return 0xffff; + } + val = (val >> 8) & 0xffff; + + spin_unlock(&psc_dma->lock); + return (unsigned short) val; +} + +static void psc_ac97_write(struct snd_ac97 *ac97, unsigned short reg, unsigned short val) +{ + int timeout; + + spin_lock(&psc_dma->lock); + + /* Wait for it to be ready */ + timeout = 1000; + while ((--timeout) && (in_be16(&psc_dma->psc_regs->sr_csr.status) & + MPC52xx_PSC_SR_CMDSEND) ) + udelay(10); + + if (!timeout) { + pr_err("timeout on ac97 write\n"); + return; + } + + /* Write data */ + out_be32(&psc_dma->psc_regs->ac97_cmd, ((reg & 0x7f) << 24) | (val << 8)); + + spin_unlock(&psc_dma->lock); +} + +static void psc_ac97_cold_reset(struct snd_ac97 *ac97) +{ + struct mpc52xx_psc __iomem *regs = psc_dma->psc_regs; + + /* Do a cold reset */ + out_8(&regs->op1, MPC52xx_PSC_OP_RES); + udelay(10); + out_8(&regs->op0, MPC52xx_PSC_OP_RES); + udelay(50); + + /* PSC recover from cold reset (cfr user manual, not sure if useful) */ + out_be32(&regs->sicr, in_be32(&regs->sicr)); +} + +static void psc_ac97_warm_reset(struct snd_ac97 *ac97) +{ + struct mpc52xx_psc __iomem *regs = psc_dma->psc_regs; + + out_be32(&regs->sicr, psc_dma->sicr | MPC52xx_PSC_SICR_AWR); + udelay(3); + out_be32(&regs->sicr, psc_dma->sicr); +} + +struct snd_ac97_bus_ops soc_ac97_ops = { + .read = psc_ac97_read, + .write = psc_ac97_write, + .reset = psc_ac97_cold_reset, + .warm_reset = psc_ac97_warm_reset, +}; +EXPORT_SYMBOL_GPL(soc_ac97_ops); + +#ifdef CONFIG_PM +static int psc_ac97_suspend(struct snd_soc_dai *dai) +{ + return 0; +} + +static int psc_ac97_resume(struct snd_soc_dai *dai) +{ + return 0; +} + +#else +#define psc_ac97_suspend NULL +#define psc_ac97_resume NULL +#endif + +static int psc_ac97_hw_analog_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data; + + dev_dbg(psc_dma->dev, "%s(substream=%p) p_size=%i p_bytes=%i" + " periods=%i buffer_size=%i buffer_bytes=%i channels=%i" + " rate=%i format=%i\n", + __func__, substream, params_period_size(params), + params_period_bytes(params), params_periods(params), + params_buffer_size(params), params_buffer_bytes(params), + params_channels(params), params_rate(params), params_format(params)); + + + if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE) { + if (params_channels(params) == 1) + psc_dma->slots |= 0x00000100; + else + psc_dma->slots |= 0x00000300; + } else { + if (params_channels(params) == 1) + psc_dma->slots |= 0x01000000; + else + psc_dma->slots |= 0x03000000; + } + + spin_lock(&psc_dma->lock); + out_be32(&psc_dma->psc_regs->ac97_slots, psc_dma->slots); + spin_unlock(&psc_dma->lock); + + return 0; +} + +static int psc_ac97_hw_digital_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data; + + spin_lock(&psc_dma->lock); + if (params_channels(params) == 1) + out_be32(&psc_dma->psc_regs->ac97_slots, 0x01000000); + else + out_be32(&psc_dma->psc_regs->ac97_slots, 0x03000000); + spin_unlock(&psc_dma->lock); + + return 0; +} + +static int psc_ac97_trigger(struct snd_pcm_substream *substream, int cmd, + struct snd_soc_dai *dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data; + + switch (cmd) { + case SNDRV_PCM_TRIGGER_STOP: + if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE) + psc_dma->slots &= 0xFFFF0000; + else + psc_dma->slots &= 0x0000FFFF; + + spin_lock(&psc_dma->lock); + out_be32(&psc_dma->psc_regs->ac97_slots, psc_dma->slots); + spin_unlock(&psc_dma->lock); + break; + } + return 0; +} + +/* --------------------------------------------------------------------- + * ALSA SoC Bindings + * + * - Digital Audio Interface (DAI) template + * - create/destroy dai hooks + */ + +/** + * psc_ac97_dai_template: template CPU Digital Audio Interface + */ +static struct snd_soc_dai_ops psc_ac97_analog_ops = { + .hw_params = psc_ac97_hw_analog_params, + .trigger = psc_ac97_trigger, +}; + +static struct snd_soc_dai_ops psc_ac97_digital_ops = { + .hw_params = psc_ac97_hw_digital_params, +}; + +struct snd_soc_dai psc_ac97_dai[] = { +{ + .name = "AC97", + .suspend = psc_ac97_suspend, + .resume = psc_ac97_resume, + .playback = { + .channels_min = 1, + .channels_max = 6, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SNDRV_PCM_FMTBIT_S32_BE, + }, + .capture = { + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SNDRV_PCM_FMTBIT_S32_BE, + }, + .ops = &psc_ac97_analog_ops, +}, +{ + .name = "SPDIF", + .playback = { + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_32000 | \ + SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000, + .formats = SNDRV_PCM_FMTBIT_IEC958_SUBFRAME_BE, + }, + .ops = &psc_ac97_digital_ops, +}}; +EXPORT_SYMBOL_GPL(psc_ac97_dai); + + + +/* --------------------------------------------------------------------- + * OF platform bus binding code: + * - Probe/remove operations + * - OF device match table + */ +static int __devinit psc_ac97_of_probe(struct of_device *op, + const struct of_device_id *match) +{ + int rc, i, id1, id2, timeout, max_reset; + struct snd_ac97 ac97; + struct mpc52xx_psc __iomem *regs; + + rc = mpc5200_audio_dma_create(op); + if (rc != 0) + return rc; + + for (i = 0; i < ARRAY_SIZE(psc_ac97_dai); i++) + psc_ac97_dai[i].dev = &op->dev; + + rc = snd_soc_register_dais(psc_ac97_dai, ARRAY_SIZE(psc_ac97_dai)); + if (rc != 0) { + pr_err("Failed to register DAI\n"); + return 0; + } + + psc_dma = dev_get_drvdata(&op->dev); + regs = psc_dma->psc_regs; + ac97.private_data = psc_dma; + + for (i = 0; i < ARRAY_SIZE(psc_ac97_dai); i++) + psc_ac97_dai[i].private_data = psc_dma; + + psc_dma->imr = 0; + out_be16(&psc_dma->psc_regs->isr_imr.imr, psc_dma->imr); + + /* Configure the serial interface mode to AC97 */ + psc_dma->sicr = MPC52xx_PSC_SICR_SIM_AC97 | MPC52xx_PSC_SICR_ENAC97; + out_be32(&regs->sicr, psc_dma->sicr); + + /* No slots active */ + out_be32(&regs->ac97_slots, 0x00000000); + + /* AC97 clock is generated by the codec. + * Ensure that it starts ticking after codec reset. + */ + max_reset = 0; +reset: + if (max_reset++ > 5) { + dev_err(&op->dev, "AC97 codec failed to reset\n"); + mpc5200_audio_dma_destroy(op); + return -ENODEV; + } + + psc_ac97_cold_reset(&ac97); + psc_ac97_warm_reset(&ac97); + + /* first make sure it is low */ + timeout = 0; + while ((in_8(&regs->ipcr_acr.ipcr) & 0x80) != 0) { + udelay(1); + if (timeout++ > 1000) + goto reset; + } + /* then wait for the transition to high */ + timeout = 0; + while ((in_8(&regs->ipcr_acr.ipcr) & 0x80) == 0) { + udelay(1); + if (timeout++ > 1000) + psc_ac97_warm_reset(&ac97); + } + + /* Go */ + out_8(&regs->command, MPC52xx_PSC_TX_ENABLE | MPC52xx_PSC_RX_ENABLE); + + id1 = psc_ac97_read(&ac97, AC97_VENDOR_ID1); + id2 = psc_ac97_read(&ac97, AC97_VENDOR_ID2); + + dev_info(&op->dev, "Codec ID is %04x %04x\n", id1, id2); + + return 0; +} + +static int __devexit psc_ac97_of_remove(struct of_device *op) +{ + return mpc5200_audio_dma_destroy(op); +} + +/* Match table for of_platform binding */ +static struct of_device_id psc_ac97_match[] __devinitdata = { + { .compatible = "fsl,mpc5200-psc-ac97", }, + { .compatible = "fsl,mpc5200b-psc-ac97", }, + {} +}; +MODULE_DEVICE_TABLE(of, psc_ac97_match); + +static struct of_platform_driver psc_ac97_driver = { + .match_table = psc_ac97_match, + .probe = psc_ac97_of_probe, + .remove = __devexit_p(psc_ac97_of_remove), + .driver = { + .name = "mpc5200-psc-ac97", + .owner = THIS_MODULE, + }, +}; + +/* --------------------------------------------------------------------- + * Module setup and teardown; simply register the of_platform driver + * for the PSC in AC97 mode. + */ +static int __init psc_ac97_init(void) +{ + return of_register_platform_driver(&psc_ac97_driver); +} +module_init(psc_ac97_init); + +static void __exit psc_ac97_exit(void) +{ + of_unregister_platform_driver(&psc_ac97_driver); +} +module_exit(psc_ac97_exit); + +MODULE_AUTHOR("Jon Smirl <jonsmirl(a)gmail.com>"); +MODULE_DESCRIPTION("mpc5200 AC97 module"); +MODULE_LICENSE("GPL"); + diff --git a/sound/soc/fsl/mpc5200_psc_ac97.h b/sound/soc/fsl/mpc5200_psc_ac97.h new file mode 100644 index 0000000..4bc18c3 --- /dev/null +++ b/sound/soc/fsl/mpc5200_psc_ac97.h @@ -0,0 +1,15 @@ +/* + * Freescale MPC5200 PSC in AC97 mode + * ALSA SoC Digital Audio Interface (DAI) driver + * + */ + +#ifndef __SOUND_SOC_FSL_MPC52xx_PSC_AC97_H__ +#define __SOUND_SOC_FSL_MPC52xx_PSC_AC97_H__ + +extern struct snd_soc_dai psc_ac97_dai[]; + +#define MPC5200_AC97_NORMAL 0 +#define MPC5200_AC97_SPDIF 1 + +#endif /* __SOUND_SOC_FSL_MPC52xx_PSC_AC97_H__ */ ------------------------------ _______________________________________________ Alsa-devel mailing list Alsa-devel(a)alsa-project.org http://mailman.alsa-project.org/mailman/listinfo/alsa-devel End of Alsa-devel Digest, Vol 27, Issue 124 *******************************************

1 0

Re: [alsa-devel] Alsa-devel Digest, Vol 27, Issue 124
by Demian Martin 24 May '09

24 May '09

Demian Martin PDS 209 613 6990 -----Original Message----- From: alsa-devel-request(a)alsa-project.org Date: Sun, 24 May 2009 01:13:19 To: <alsa-devel(a)alsa-project.org> Subject: Alsa-devel Digest, Vol 27, Issue 124 Send Alsa-devel mailing list submissions to alsa-devel(a)alsa-project.org To subscribe or unsubscribe via the World Wide Web, visit http://mailman.alsa-project.org/mailman/listinfo/alsa-devel or, via email, send a message with subject or body 'help' to alsa-devel-request(a)alsa-project.org You can reach the person managing the list at alsa-devel-owner(a)alsa-project.org When replying, please edit your Subject line so it is more specific than "Re: Contents of Alsa-devel digest..." Today's Topics: 1. [PATCH V2 4/9] Add a few more mpc5200 PSC defines (Jon Smirl) 2. [PATCH V2 6/9] Codec for STAC9766 used on the Efika (Jon Smirl) 3. [PATCH V2 7/9] AC97 driver for mpc5200 (Jon Smirl) ---------------------------------------------------------------------- Message: 1 Date: Sat, 23 May 2009 19:13:03 -0400 From: Jon Smirl <jonsmirl(a)gmail.com> Subject: [alsa-devel] [PATCH V2 4/9] Add a few more mpc5200 PSC defines To: grant.likely(a)secretlab.ca, linuxppc-dev(a)ozlabs.org, alsa-devel(a)alsa-project.org, broonie(a)sirena.org.uk Message-ID: <20090523231303.17919.35877.stgit@terra> Content-Type: text/plain; charset="utf-8" Add a few more mpc5200 PSC defines. More bit fields defines for mpc5200 PSC registers. This patch is going in via Grant's tree. Signed-off-by: Jon Smirl <jonsmirl(a)gmail.com> --- 0 files changed, 0 insertions(+), 0 deletions(-) diff --git a/arch/powerpc/include/asm/mpc52xx_psc.h b/arch/powerpc/include/asm/mpc52xx_psc.h index a218da6..fb84120 100644 --- a/arch/powerpc/include/asm/mpc52xx_psc.h +++ b/arch/powerpc/include/asm/mpc52xx_psc.h @@ -28,6 +28,10 @@ #define MPC52xx_PSC_MAXNUM 6 /* Programmable Serial Controller (PSC) status register bits */ +#define MPC52xx_PSC_SR_UNEX_RX 0x0001 +#define MPC52xx_PSC_SR_DATA_VAL 0x0002 +#define MPC52xx_PSC_SR_DATA_OVR 0x0004 +#define MPC52xx_PSC_SR_CMDSEND 0x0008 #define MPC52xx_PSC_SR_CDE 0x0080 #define MPC52xx_PSC_SR_RXRDY 0x0100 #define MPC52xx_PSC_SR_RXFULL 0x0200 @@ -61,6 +65,12 @@ #define MPC52xx_PSC_RXTX_FIFO_EMPTY 0x0001 /* PSC interrupt status/mask bits */ +#define MPC52xx_PSC_IMR_UNEX_RX_SLOT 0x0001 +#define MPC52xx_PSC_IMR_DATA_VALID 0x0002 +#define MPC52xx_PSC_IMR_DATA_OVR 0x0004 +#define MPC52xx_PSC_IMR_CMD_SEND 0x0008 +#define MPC52xx_PSC_IMR_ERROR 0x0040 +#define MPC52xx_PSC_IMR_DEOF 0x0080 #define MPC52xx_PSC_IMR_TXRDY 0x0100 #define MPC52xx_PSC_IMR_RXRDY 0x0200 #define MPC52xx_PSC_IMR_DB 0x0400 @@ -117,6 +127,7 @@ #define MPC52xx_PSC_SICR_SIM_FIR (0x6 << 24) #define MPC52xx_PSC_SICR_SIM_CODEC_24 (0x7 << 24) #define MPC52xx_PSC_SICR_SIM_CODEC_32 (0xf << 24) +#define MPC52xx_PSC_SICR_AWR (1 << 30) #define MPC52xx_PSC_SICR_GENCLK (1 << 23) #define MPC52xx_PSC_SICR_I2S (1 << 22) #define MPC52xx_PSC_SICR_CLKPOL (1 << 21) ------------------------------ Message: 2 Date: Sat, 23 May 2009 19:13:07 -0400 From: Jon Smirl <jonsmirl(a)gmail.com> Subject: [alsa-devel] [PATCH V2 6/9] Codec for STAC9766 used on the Efika To: grant.likely(a)secretlab.ca, linuxppc-dev(a)ozlabs.org, alsa-devel(a)alsa-project.org, broonie(a)sirena.org.uk Message-ID: <20090523231307.17919.5277.stgit@terra> Content-Type: text/plain; charset="utf-8" AC97 codec for STAC9766 used on the Efika. Datasheet: http://www.idt.com/products/getDoc.cfm?docID=13134007 Signed-off-by: Jon Smirl <jonsmirl(a)gmail.com> --- 0 files changed, 0 insertions(+), 0 deletions(-) diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 7f78b65..cb07d9b 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -19,6 +19,7 @@ config SND_SOC_ALL_CODECS select SND_SOC_CS4270 if I2C select SND_SOC_PCM3008 select SND_SOC_SSM2602 if I2C + select SND_SOC_STAC9766 if SND_SOC_AC97_BUS select SND_SOC_TLV320AIC23 if I2C select SND_SOC_TLV320AIC26 if SPI_MASTER select SND_SOC_TLV320AIC3X if I2C @@ -93,6 +94,9 @@ config SND_SOC_PCM3008 config SND_SOC_SSM2602 tristate +config SND_SOC_STAC9766 + tristate + config SND_SOC_TLV320AIC23 tristate diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 70c55fa..46c007c 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -7,6 +7,7 @@ snd-soc-cs4270-objs := cs4270.o snd-soc-l3-objs := l3.o snd-soc-pcm3008-objs := pcm3008.o snd-soc-ssm2602-objs := ssm2602.o +snd-soc-stac9766-objs := stac9766.o snd-soc-tlv320aic23-objs := tlv320aic23.o snd-soc-tlv320aic26-objs := tlv320aic26.o snd-soc-tlv320aic3x-objs := tlv320aic3x.o @@ -42,6 +43,7 @@ obj-$(CONFIG_SND_SOC_CS4270) += snd-soc-cs4270.o obj-$(CONFIG_SND_SOC_L3) += snd-soc-l3.o obj-$(CONFIG_SND_SOC_PCM3008) += snd-soc-pcm3008.o obj-$(CONFIG_SND_SOC_SSM2602) += snd-soc-ssm2602.o +obj-$(CONFIG_SND_SOC_STAC9766) += snd-soc-stac9766.o obj-$(CONFIG_SND_SOC_TLV320AIC23) += snd-soc-tlv320aic23.o obj-$(CONFIG_SND_SOC_TLV320AIC26) += snd-soc-tlv320aic26.o obj-$(CONFIG_SND_SOC_TLV320AIC3X) += snd-soc-tlv320aic3x.o diff --git a/sound/soc/codecs/stac9766.c b/sound/soc/codecs/stac9766.c new file mode 100644 index 0000000..7740cd5 --- /dev/null +++ b/sound/soc/codecs/stac9766.c @@ -0,0 +1,470 @@ +/* + * stac9766.c -- ALSA SoC STAC9766 codec support + * + * Copyright 2009 Jon Smirl, Digispeaker + * Author: Jon Smirl <jonsmirl(a)gmail.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * Features:- + * + * o Support for AC97 Codec, S/PDIF + */ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/device.h> +#include <sound/core.h> +#include <sound/pcm.h> +#include <sound/ac97_codec.h> +#include <sound/initval.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/tlv.h> +#include <sound/soc-of-simple.h> + +#include "stac9766.h" + +#define STAC9766_VERSION "0.10" + +/* + * STAC9766 register cache + */ +static const u16 stac9766_reg[] = { + 0x6A90, 0x8000, 0x8000, 0x8000, /* 6 */ + 0x0000, 0x0000, 0x8008, 0x8008, /* e */ + 0x8808, 0x8808, 0x8808, 0x8808, /* 16 */ + 0x8808, 0x0000, 0x8000, 0x0000, /* 1e */ + 0x0000, 0x0000, 0x0000, 0x000f, /* 26 */ + 0x0a05, 0x0400, 0xbb80, 0x0000, /* 2e */ + 0x0000, 0xbb80, 0x0000, 0x0000, /* 36 */ + 0x0000, 0x2000, 0x0000, 0x0100, /* 3e */ + 0x0000, 0x0000, 0x0080, 0x0000, /* 46 */ + 0x0000, 0x0000, 0x0003, 0xffff, /* 4e */ + 0x0000, 0x0000, 0x0000, 0x0000, /* 56 */ + 0x4000, 0x0000, 0x0000, 0x0000, /* 5e */ + 0x1201, 0xFFFF, 0xFFFF, 0x0000, /* 66 */ + 0x0000, 0x0000, 0x0000, 0x0000, /* 6e */ + 0x0000, 0x0000, 0x0000, 0x0006, /* 76 */ + 0x0000, 0x0000, 0x0000, 0x0000, /* 7e */ +}; + +static const char *stac9766_record_mux[] = {"Mic", "CD", "Video", "AUX", "Line", "Stereo Mix", "Mono Mix", "Phone"}; +static const char *stac9766_mono_mux[] = {"Mix", "Mic"}; +static const char *stac9766_mic_mux[] = {"Mic1", "Mic2"}; +static const char *stac9766_SPDIF_mux[] = {"PCM", "ADC Record"}; +static const char *stac9766_popbypass_mux[] = {"Normal", "Bypass Mixer"}; +static const char *stac9766_record_all_mux[] = {"All analog", "Analog plus DAC"}; +static const char *stac9766_boost1[] = {"0dB", "10dB"}; +static const char *stac9766_boost2[] = {"0dB", "20dB"}; +static const char *stac9766_stereo_mic[] = {"Off", "On"}; + +static const struct soc_enum stac9766_record_enum = + SOC_ENUM_DOUBLE(AC97_REC_SEL, 8, 0, 8, stac9766_record_mux); +static const struct soc_enum stac9766_mono_enum = + SOC_ENUM_SINGLE(AC97_GENERAL_PURPOSE, 9, 2, stac9766_mono_mux); +static const struct soc_enum stac9766_mic_enum = + SOC_ENUM_SINGLE(AC97_GENERAL_PURPOSE, 8, 2, stac9766_mic_mux); +static const struct soc_enum stac9766_SPDIF_enum = + SOC_ENUM_SINGLE(AC97_STAC_DA_CONTROL, 1, 2, stac9766_SPDIF_mux); +static const struct soc_enum stac9766_popbypass_enum = + SOC_ENUM_SINGLE(AC97_GENERAL_PURPOSE, 15, 2, stac9766_popbypass_mux); +static const struct soc_enum stac9766_record_all_enum = + SOC_ENUM_SINGLE(AC97_STAC_ANALOG_SPECIAL, 12, 2, stac9766_record_all_mux); +static const struct soc_enum stac9766_boost1_enum = + SOC_ENUM_SINGLE(AC97_MIC, 6, 2, stac9766_boost1); /* 0/10dB */ +static const struct soc_enum stac9766_boost2_enum = + SOC_ENUM_SINGLE(AC97_STAC_ANALOG_SPECIAL, 2, 2, stac9766_boost2); /* 0/20dB */ +static const struct soc_enum stac9766_stereo_mic_enum = + SOC_ENUM_SINGLE(AC97_STAC_STEREO_MIC, 2, 1, stac9766_stereo_mic); + +static const DECLARE_TLV_DB_LINEAR(master_tlv, -4600, 0); +static const DECLARE_TLV_DB_LINEAR(record_tlv, 0, 2250); +static const DECLARE_TLV_DB_LINEAR(beep_tlv, -4500, 0); +static const DECLARE_TLV_DB_LINEAR(mix_tlv, -3450, 1200); + +static const struct snd_kcontrol_new stac9766_snd_ac97_controls[] = { + SOC_DOUBLE_TLV("Speaker Volume", AC97_MASTER, 8, 0, 31, 1, master_tlv), + SOC_SINGLE("Speaker Switch", AC97_MASTER, 15, 1, 1), + SOC_DOUBLE_TLV("Headphone Volume", AC97_HEADPHONE, 8, 0, 31, 1, master_tlv), + SOC_SINGLE("Headphone Switch", AC97_HEADPHONE, 15, 1, 1), + SOC_SINGLE_TLV("Mono Out Volume", AC97_MASTER_MONO, 0, 31, 1, master_tlv), + SOC_SINGLE("Mono Out Switch", AC97_MASTER_MONO, 15, 1, 1), + + SOC_DOUBLE_TLV("Record Volume", AC97_REC_GAIN, 8, 0, 15, 0, record_tlv), + SOC_SINGLE("Record Switch", AC97_REC_GAIN, 15, 1, 1), + + + SOC_SINGLE_TLV("Beep Volume", AC97_PC_BEEP, 1, 15, 1, beep_tlv), + SOC_SINGLE("Beep Switch", AC97_PC_BEEP, 15, 1, 1), + SOC_SINGLE("Beep Frequency", AC97_PC_BEEP, 5, 127, 1), + SOC_SINGLE_TLV("Phone Volume", AC97_PHONE, 0, 31, 1, mix_tlv), + SOC_SINGLE("Phone Switch", AC97_PHONE, 15, 1, 1), + + SOC_ENUM("Mic Boost1", stac9766_boost1_enum), + SOC_ENUM("Mic Boost2", stac9766_boost2_enum), + SOC_SINGLE_TLV("Mic Volume", AC97_MIC, 0, 31, 1, mix_tlv), + SOC_SINGLE("Mic Switch", AC97_MIC, 15, 1, 1), + SOC_ENUM("Stereo Mic", stac9766_stereo_mic_enum), + + SOC_DOUBLE_TLV("Line Volume", AC97_LINE, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("Line Switch", AC97_LINE, 15, 1, 1), + SOC_DOUBLE_TLV("CD Volume", AC97_CD, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("CD Switch", AC97_CD, 15, 1, 1), + SOC_DOUBLE_TLV("AUX Volume", AC97_AUX, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("AUX Switch", AC97_AUX, 15, 1, 1), + SOC_DOUBLE_TLV("Video Volume", AC97_VIDEO, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("Video Switch", AC97_VIDEO, 15, 1, 1), + + SOC_DOUBLE_TLV("DAC Volume", AC97_PCM, 8, 0, 31, 1, mix_tlv), + SOC_SINGLE("DAC Switch", AC97_PCM, 15, 1, 1), + SOC_SINGLE("Loopback Test Switch", AC97_GENERAL_PURPOSE, 7, 1, 0), + SOC_SINGLE("3D Volume", AC97_3D_CONTROL, 3, 2, 1), + SOC_SINGLE("3D Switch", AC97_GENERAL_PURPOSE, 13, 1, 0), + + SOC_ENUM("SPDIF Mux", stac9766_SPDIF_enum), + SOC_ENUM("Mic1/2 Mux", stac9766_mic_enum), + SOC_ENUM("Record All Mux", stac9766_record_all_enum), + SOC_ENUM("Record Mux", stac9766_record_enum), + SOC_ENUM("Mono Mux", stac9766_mono_enum), + SOC_ENUM("Pop Bypass Mux", stac9766_popbypass_enum), +}; + +int stac9766_ac97_write(struct snd_soc_codec *codec, unsigned int reg, + unsigned int val) +{ + u16 *cache = codec->reg_cache; + + if (reg > AC97_STAC_PAGE0) { + stac9766_ac97_write(codec, AC97_INT_PAGING, 0); + soc_ac97_ops.write(codec->ac97, reg, val); + stac9766_ac97_write(codec, AC97_INT_PAGING, 1); + return 0; + } + if (reg / 2 > ARRAY_SIZE(stac9766_reg)) + return -EIO; + + soc_ac97_ops.write(codec->ac97, reg, val); + cache[reg / 2] = val; + return 0; +} + +unsigned int stac9766_ac97_read(struct snd_soc_codec *codec, unsigned int reg) +{ + u16 val = 0, *cache = codec->reg_cache; + + if (reg > AC97_STAC_PAGE0) { + stac9766_ac97_write(codec, AC97_INT_PAGING, 0); + val = soc_ac97_ops.read(codec->ac97, reg - AC97_STAC_PAGE0); + stac9766_ac97_write(codec, AC97_INT_PAGING, 1); + return val; + } + if (reg / 2 > ARRAY_SIZE(stac9766_reg)) + return -EIO; + + if (reg == AC97_RESET || reg == AC97_GPIO_STATUS || + reg == AC97_INT_PAGING || reg == AC97_VENDOR_ID1 || + reg == AC97_VENDOR_ID2) { + + val = soc_ac97_ops.read(codec->ac97, reg); + return val; + } + return cache[reg / 2]; +} + +static int ac97_analog_prepare(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct snd_soc_codec *codec = dai->codec; + struct snd_pcm_runtime *runtime = substream->runtime; + unsigned short reg, vra; + + vra = stac9766_ac97_read(codec, AC97_EXTENDED_STATUS); + + vra |= 0x1; /* enable variable rate audio */ + + stac9766_ac97_write(codec, AC97_EXTENDED_STATUS, vra); + + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) + reg = AC97_PCM_FRONT_DAC_RATE; + else + reg = AC97_PCM_LR_ADC_RATE; + + return stac9766_ac97_write(codec, reg, runtime->rate); +} + +static int ac97_digital_prepare(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct snd_soc_codec *codec = dai->codec; + struct snd_pcm_runtime *runtime = substream->runtime; + unsigned short reg, vra; + + stac9766_ac97_write(codec, AC97_SPDIF, 0x2002); + + vra = stac9766_ac97_read(codec, AC97_EXTENDED_STATUS); + vra |= 0x5; /* Enable VRA and SPDIF out */ + + stac9766_ac97_write(codec, AC97_EXTENDED_STATUS, vra); + + reg = AC97_PCM_FRONT_DAC_RATE; + + return stac9766_ac97_write(codec, reg, runtime->rate); +} + +static int ac97_digital_trigger(struct snd_pcm_substream *substream, + int cmd, struct snd_soc_dai *dai) +{ + struct snd_soc_codec *codec = dai->codec; + unsigned short vra; + + switch (cmd) { + case SNDRV_PCM_TRIGGER_STOP: + vra = stac9766_ac97_read(codec, AC97_EXTENDED_STATUS); + vra &= !0x04; + stac9766_ac97_write(codec, AC97_EXTENDED_STATUS, vra); + break; + } + return 0; +} + +static int stac9766_set_bias_level(struct snd_soc_codec *codec, + enum snd_soc_bias_level level) +{ + switch (level) { + case SND_SOC_BIAS_ON: /* full On */ + case SND_SOC_BIAS_PREPARE: /* partial On */ + case SND_SOC_BIAS_STANDBY: /* Off, with power */ + stac9766_ac97_write(codec, AC97_POWERDOWN, 0x0000); + break; + case SND_SOC_BIAS_OFF: /* Off, without power */ + /* disable everything including AC link */ + stac9766_ac97_write(codec, AC97_POWERDOWN, 0xffff); + break; + } + codec->bias_level = level; + return 0; +} + +int stac9766_reset(struct snd_soc_codec *codec, int try_warm) +{ + if (try_warm && soc_ac97_ops.warm_reset) { + soc_ac97_ops.warm_reset(codec->ac97); + if (stac9766_ac97_read(codec, 0) == stac9766_reg[0]) + return 1; + } + + soc_ac97_ops.reset(codec->ac97); + if (soc_ac97_ops.warm_reset) + soc_ac97_ops.warm_reset(codec->ac97); + if (stac9766_ac97_read(codec, 0) != stac9766_reg[0]) + return -EIO; + return 0; +} + +static int stac9766_codec_suspend(struct platform_device *pdev, + pm_message_t state) +{ + struct snd_soc_device *socdev = platform_get_drvdata(pdev); + struct snd_soc_codec *codec = socdev->card->codec; + + stac9766_set_bias_level(codec, SND_SOC_BIAS_OFF); + return 0; +} + +static int stac9766_codec_resume(struct platform_device *pdev) +{ + struct snd_soc_device *socdev = platform_get_drvdata(pdev); + struct snd_soc_codec *codec = socdev->card->codec; + u16 id, reset; + + reset = 0; + /* give the codec an AC97 warm reset to start the link */ +reset: + if (reset > 5) { + printk(KERN_ERR "stac9766 failed to resume"); + return -EIO; + } + codec->ac97->bus->ops->warm_reset(codec->ac97); + id = soc_ac97_ops.read(codec->ac97, AC97_VENDOR_ID2); + if (id != 0x4c13) { + stac9766_reset(codec, 0); + reset++; + goto reset; + } + stac9766_set_bias_level(codec, SND_SOC_BIAS_STANDBY); + + if (codec->suspend_bias_level == SND_SOC_BIAS_ON) + stac9766_set_bias_level(codec, SND_SOC_BIAS_ON); + + return 0; +} + +static struct snd_soc_dai_ops stac9766_dai_ops_analog = +{ + .prepare = ac97_analog_prepare, +}; + +static struct snd_soc_dai_ops stac9766_dai_ops_digital = +{ + .prepare = ac97_digital_prepare, + .trigger = ac97_digital_trigger, +}; + +struct snd_soc_dai stac9766_dai[] = { +{ + .name = "stac9766 analog", + .id = 0, + .ac97_control = 1, + + /* stream cababilities */ + .playback = { + .stream_name = "stac9766 analog", + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SND_SOC_STD_AC97_FMTS, + }, + .capture = { + .stream_name = "stac9766 analog", + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SND_SOC_STD_AC97_FMTS, + }, + /* alsa ops */ + .ops = &stac9766_dai_ops_analog, +}, +{ + .name = "stac9766 IEC958", + .id = 1, + .ac97_control = 1, + + /* stream cababilities */ + .playback = { + .stream_name = "stac9766 IEC958", + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_32000 | \ + SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000, + .formats = SNDRV_PCM_FORMAT_IEC958_SUBFRAME_BE, + }, + /* alsa ops */ + .ops = &stac9766_dai_ops_digital, +}}; +EXPORT_SYMBOL_GPL(stac9766_dai); + +static int stac9766_codec_probe(struct platform_device *pdev) +{ + struct snd_soc_device *socdev = platform_get_drvdata(pdev); + struct snd_soc_codec *codec; + int ret = 0; + + printk(KERN_INFO "STAC9766 SoC Audio Codec %s\n", STAC9766_VERSION); + + socdev->card->codec = kzalloc(sizeof(struct snd_soc_codec), GFP_KERNEL); + if (socdev->card->codec == NULL) + return -ENOMEM; + codec = socdev->card->codec; + mutex_init(&codec->mutex); + + codec->reg_cache = kmemdup(stac9766_reg, sizeof(stac9766_reg), GFP_KERNEL); + if (codec->reg_cache == NULL) { + ret = -ENOMEM; + goto cache_err; + } + codec->reg_cache_size = sizeof(stac9766_reg); + codec->reg_cache_step = 2; + + codec->name = "STAC9766"; + codec->owner = THIS_MODULE; + codec->dai = stac9766_dai; + codec->num_dai = ARRAY_SIZE(stac9766_dai); + codec->write = stac9766_ac97_write; + codec->read = stac9766_ac97_read; + codec->set_bias_level = stac9766_set_bias_level; + INIT_LIST_HEAD(&codec->dapm_widgets); + INIT_LIST_HEAD(&codec->dapm_paths); + + ret = snd_soc_new_ac97_codec(codec, &soc_ac97_ops, 0); + if (ret < 0) + goto codec_err; + + /* register pcms */ + ret = snd_soc_new_pcms(socdev, SNDRV_DEFAULT_IDX1, SNDRV_DEFAULT_STR1); + if (ret < 0) + goto pcm_err; + + /* do a cold reset for the controller and then try + * a warm reset followed by an optional cold reset for codec */ + stac9766_reset(codec, 0); + ret = stac9766_reset(codec, 1); + if (ret < 0) { + printk(KERN_ERR "Failed to reset STAC9766: AC97 link error\n"); + goto reset_err; + } + + stac9766_set_bias_level(codec, SND_SOC_BIAS_STANDBY); + + snd_soc_add_controls(codec, stac9766_snd_ac97_controls, ARRAY_SIZE( + stac9766_snd_ac97_controls)); + + ret = snd_soc_init_card(socdev); + if (ret < 0) + goto reset_err; + return 0; + +reset_err: + snd_soc_free_pcms(socdev); +pcm_err: + snd_soc_free_ac97_codec(codec); +codec_err: + kfree(codec->private_data); +cache_err: + kfree(socdev->card->codec); + socdev->card->codec = NULL; + return ret; +} + +static int stac9766_codec_remove(struct platform_device *pdev) +{ + struct snd_soc_device *socdev = platform_get_drvdata(pdev); + struct snd_soc_codec *codec = socdev->card->codec; + + if (codec == NULL) + return 0; + + snd_soc_free_pcms(socdev); + snd_soc_free_ac97_codec(codec); + kfree(codec->reg_cache); + kfree(codec); + return 0; +} + +struct snd_soc_codec_device soc_codec_dev_stac9766 = +{ + .probe = stac9766_codec_probe, + .remove = stac9766_codec_remove, + .suspend = stac9766_codec_suspend, + .resume = stac9766_codec_resume, +}; +EXPORT_SYMBOL_GPL(soc_codec_dev_stac9766); + +static int __init stac9766_modinit(void) +{ + return snd_soc_register_dais(stac9766_dai, ARRAY_SIZE(stac9766_dai)); +} +module_init(stac9766_modinit); + +static void __exit stac9766_exit(void) +{ + snd_soc_unregister_dais(stac9766_dai, ARRAY_SIZE(stac9766_dai)); +} +module_exit(stac9766_exit); + +MODULE_DESCRIPTION("ASoC stac9766 driver"); +MODULE_AUTHOR("Jon Smirl <jonsmirl(a)gmail.com>"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/stac9766.h b/sound/soc/codecs/stac9766.h new file mode 100644 index 0000000..65642eb --- /dev/null +++ b/sound/soc/codecs/stac9766.h @@ -0,0 +1,21 @@ +/* + * stac9766.h -- STAC9766 Soc Audio driver + */ + +#ifndef _STAC9766_H +#define _STAC9766_H + +#define AC97_STAC_PAGE0 0x1000 +#define AC97_STAC_DA_CONTROL (AC97_STAC_PAGE0 | 0x6A) +#define AC97_STAC_ANALOG_SPECIAL (AC97_STAC_PAGE0 | 0x6E) +#define AC97_STAC_STEREO_MIC 0x78 + +/* STAC9766 DAI ID's */ +#define STAC9766_DAI_AC97_ANALOG 0 +#define STAC9766_DAI_AC97_DIGITAL 1 + +extern struct snd_soc_dai stac9766_dai[]; +extern struct snd_soc_codec_device soc_codec_dev_stac9766; + + +#endif ------------------------------ Message: 3 Date: Sat, 23 May 2009 19:13:09 -0400 From: Jon Smirl <jonsmirl(a)gmail.com> Subject: [alsa-devel] [PATCH V2 7/9] AC97 driver for mpc5200 To: grant.likely(a)secretlab.ca, linuxppc-dev(a)ozlabs.org, alsa-devel(a)alsa-project.org, broonie(a)sirena.org.uk Message-ID: <20090523231309.17919.83073.stgit@terra> Content-Type: text/plain; charset="utf-8" AC97 driver for mpc5200 Signed-off-by: Jon Smirl <jonsmirl(a)gmail.com> --- sound/soc/fsl/Kconfig | 11 + sound/soc/fsl/Makefile | 1 sound/soc/fsl/mpc5200_psc_ac97.c | 394 ++++++++++++++++++++++++++++++++++++++ sound/soc/fsl/mpc5200_psc_ac97.h | 15 + 4 files changed, 421 insertions(+), 0 deletions(-) create mode 100644 sound/soc/fsl/mpc5200_psc_ac97.c create mode 100644 sound/soc/fsl/mpc5200_psc_ac97.h diff --git a/sound/soc/fsl/Kconfig b/sound/soc/fsl/Kconfig index 1918c78..3bce952 100644 --- a/sound/soc/fsl/Kconfig +++ b/sound/soc/fsl/Kconfig @@ -29,3 +29,14 @@ config SND_SOC_MPC5200_I2S select PPC_BESTCOMM_GEN_BD help Say Y here to support the MPC5200 PSCs in I2S mode. + +config SND_SOC_MPC5200_AC97 + tristate "Freescale MPC5200 PSC in AC97 mode driver" + depends on PPC_MPC52xx && PPC_BESTCOMM + select AC97_BUS + select SND_MPC52xx_DMA + select PPC_BESTCOMM_GEN_BD + help + Say Y here to support the MPC5200 PSCs in AC97 mode. + + diff --git a/sound/soc/fsl/Makefile b/sound/soc/fsl/Makefile index 7731ef2..14631a1 100644 --- a/sound/soc/fsl/Makefile +++ b/sound/soc/fsl/Makefile @@ -13,4 +13,5 @@ obj-$(CONFIG_SND_SOC_MPC8610) += snd-soc-fsl-ssi.o snd-soc-fsl-dma.o # MPC5200 Platform Support obj-$(CONFIG_SND_MPC52xx_DMA) += mpc5200_dma.o obj-$(CONFIG_SND_SOC_MPC5200_I2S) += mpc5200_psc_i2s.o +obj-$(CONFIG_SND_SOC_MPC5200_AC97) += mpc5200_psc_ac97.o diff --git a/sound/soc/fsl/mpc5200_psc_ac97.c b/sound/soc/fsl/mpc5200_psc_ac97.c new file mode 100644 index 0000000..fa1bb9a --- /dev/null +++ b/sound/soc/fsl/mpc5200_psc_ac97.c @@ -0,0 +1,394 @@ +/* + * linux/sound/mpc5200-ac97.c -- AC97 support for the Freescale MPC52xx chip. + * + * Copyright (C) 2009 Jon Smirl, Digispeaker + * Author: Jon Smirl <jonsmirl(a)gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/of_platform.h> + +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> + +#include <asm/mpc52xx_psc.h> + +#include "mpc5200_dma.h" +#include "mpc5200_psc_ac97.h" + +#define DRV_NAME "mpc5200-psc-ac97" + +/* ALSA only supports a single AC97 device so static is recommend here */ +static struct psc_dma *psc_dma; + +static unsigned short psc_ac97_read(struct snd_ac97 *ac97, unsigned short reg) +{ + int timeout; + unsigned int val; + + spin_lock(&psc_dma->lock); + + /* Wait for it to be ready */ + timeout = 1000; + while ((--timeout) && (in_be16(&psc_dma->psc_regs->sr_csr.status) & + MPC52xx_PSC_SR_CMDSEND) ) + udelay(10); + + if (!timeout) { + pr_err("timeout on ac97 bus (rdy)\n"); + return 0xffff; + } + + /* Do the read */ + out_be32(&psc_dma->psc_regs->ac97_cmd, (1<<31) | ((reg & 0x7f) << 24)); + + /* Wait for the answer */ + timeout = 1000; + while ((--timeout) && !(in_be16(&psc_dma->psc_regs->sr_csr.status) & + MPC52xx_PSC_SR_DATA_VAL) ) + udelay(10); + + if (!timeout) { + pr_err("timeout on ac97 read (val) %x\n", in_be16(&psc_dma->psc_regs->sr_csr.status)); + return 0xffff; + } + + /* Get the data */ + val = in_be32(&psc_dma->psc_regs->ac97_data); + if ( ((val>>24) & 0x7f) != reg ) { + pr_err("reg echo error on ac97 read\n"); + return 0xffff; + } + val = (val >> 8) & 0xffff; + + spin_unlock(&psc_dma->lock); + return (unsigned short) val; +} + +static void psc_ac97_write(struct snd_ac97 *ac97, unsigned short reg, unsigned short val) +{ + int timeout; + + spin_lock(&psc_dma->lock); + + /* Wait for it to be ready */ + timeout = 1000; + while ((--timeout) && (in_be16(&psc_dma->psc_regs->sr_csr.status) & + MPC52xx_PSC_SR_CMDSEND) ) + udelay(10); + + if (!timeout) { + pr_err("timeout on ac97 write\n"); + return; + } + + /* Write data */ + out_be32(&psc_dma->psc_regs->ac97_cmd, ((reg & 0x7f) << 24) | (val << 8)); + + spin_unlock(&psc_dma->lock); +} + +static void psc_ac97_cold_reset(struct snd_ac97 *ac97) +{ + struct mpc52xx_psc __iomem *regs = psc_dma->psc_regs; + + /* Do a cold reset */ + out_8(&regs->op1, MPC52xx_PSC_OP_RES); + udelay(10); + out_8(&regs->op0, MPC52xx_PSC_OP_RES); + udelay(50); + + /* PSC recover from cold reset (cfr user manual, not sure if useful) */ + out_be32(&regs->sicr, in_be32(&regs->sicr)); +} + +static void psc_ac97_warm_reset(struct snd_ac97 *ac97) +{ + struct mpc52xx_psc __iomem *regs = psc_dma->psc_regs; + + out_be32(&regs->sicr, psc_dma->sicr | MPC52xx_PSC_SICR_AWR); + udelay(3); + out_be32(&regs->sicr, psc_dma->sicr); +} + +struct snd_ac97_bus_ops soc_ac97_ops = { + .read = psc_ac97_read, + .write = psc_ac97_write, + .reset = psc_ac97_cold_reset, + .warm_reset = psc_ac97_warm_reset, +}; +EXPORT_SYMBOL_GPL(soc_ac97_ops); + +#ifdef CONFIG_PM +static int psc_ac97_suspend(struct snd_soc_dai *dai) +{ + return 0; +} + +static int psc_ac97_resume(struct snd_soc_dai *dai) +{ + return 0; +} + +#else +#define psc_ac97_suspend NULL +#define psc_ac97_resume NULL +#endif + +static int psc_ac97_hw_analog_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data; + + dev_dbg(psc_dma->dev, "%s(substream=%p) p_size=%i p_bytes=%i" + " periods=%i buffer_size=%i buffer_bytes=%i channels=%i" + " rate=%i format=%i\n", + __func__, substream, params_period_size(params), + params_period_bytes(params), params_periods(params), + params_buffer_size(params), params_buffer_bytes(params), + params_channels(params), params_rate(params), params_format(params)); + + + if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE) { + if (params_channels(params) == 1) + psc_dma->slots |= 0x00000100; + else + psc_dma->slots |= 0x00000300; + } else { + if (params_channels(params) == 1) + psc_dma->slots |= 0x01000000; + else + psc_dma->slots |= 0x03000000; + } + + spin_lock(&psc_dma->lock); + out_be32(&psc_dma->psc_regs->ac97_slots, psc_dma->slots); + spin_unlock(&psc_dma->lock); + + return 0; +} + +static int psc_ac97_hw_digital_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data; + + spin_lock(&psc_dma->lock); + if (params_channels(params) == 1) + out_be32(&psc_dma->psc_regs->ac97_slots, 0x01000000); + else + out_be32(&psc_dma->psc_regs->ac97_slots, 0x03000000); + spin_unlock(&psc_dma->lock); + + return 0; +} + +static int psc_ac97_trigger(struct snd_pcm_substream *substream, int cmd, + struct snd_soc_dai *dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct psc_dma *psc_dma = rtd->dai->cpu_dai->private_data; + + switch (cmd) { + case SNDRV_PCM_TRIGGER_STOP: + if (substream->pstr->stream == SNDRV_PCM_STREAM_CAPTURE) + psc_dma->slots &= 0xFFFF0000; + else + psc_dma->slots &= 0x0000FFFF; + + spin_lock(&psc_dma->lock); + out_be32(&psc_dma->psc_regs->ac97_slots, psc_dma->slots); + spin_unlock(&psc_dma->lock); + break; + } + return 0; +} + +/* --------------------------------------------------------------------- + * ALSA SoC Bindings + * + * - Digital Audio Interface (DAI) template + * - create/destroy dai hooks + */ + +/** + * psc_ac97_dai_template: template CPU Digital Audio Interface + */ +static struct snd_soc_dai_ops psc_ac97_analog_ops = { + .hw_params = psc_ac97_hw_analog_params, + .trigger = psc_ac97_trigger, +}; + +static struct snd_soc_dai_ops psc_ac97_digital_ops = { + .hw_params = psc_ac97_hw_digital_params, +}; + +struct snd_soc_dai psc_ac97_dai[] = { +{ + .name = "AC97", + .suspend = psc_ac97_suspend, + .resume = psc_ac97_resume, + .playback = { + .channels_min = 1, + .channels_max = 6, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SNDRV_PCM_FMTBIT_S32_BE, + }, + .capture = { + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SNDRV_PCM_FMTBIT_S32_BE, + }, + .ops = &psc_ac97_analog_ops, +}, +{ + .name = "SPDIF", + .playback = { + .channels_min = 1, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_32000 | \ + SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000, + .formats = SNDRV_PCM_FMTBIT_IEC958_SUBFRAME_BE, + }, + .ops = &psc_ac97_digital_ops, +}}; +EXPORT_SYMBOL_GPL(psc_ac97_dai); + + + +/* --------------------------------------------------------------------- + * OF platform bus binding code: + * - Probe/remove operations + * - OF device match table + */ +static int __devinit psc_ac97_of_probe(struct of_device *op, + const struct of_device_id *match) +{ + int rc, i, id1, id2, timeout, max_reset; + struct snd_ac97 ac97; + struct mpc52xx_psc __iomem *regs; + + rc = mpc5200_audio_dma_create(op); + if (rc != 0) + return rc; + + for (i = 0; i < ARRAY_SIZE(psc_ac97_dai); i++) + psc_ac97_dai[i].dev = &op->dev; + + rc = snd_soc_register_dais(psc_ac97_dai, ARRAY_SIZE(psc_ac97_dai)); + if (rc != 0) { + pr_err("Failed to register DAI\n"); + return 0; + } + + psc_dma = dev_get_drvdata(&op->dev); + regs = psc_dma->psc_regs; + ac97.private_data = psc_dma; + + for (i = 0; i < ARRAY_SIZE(psc_ac97_dai); i++) + psc_ac97_dai[i].private_data = psc_dma; + + psc_dma->imr = 0; + out_be16(&psc_dma->psc_regs->isr_imr.imr, psc_dma->imr); + + /* Configure the serial interface mode to AC97 */ + psc_dma->sicr = MPC52xx_PSC_SICR_SIM_AC97 | MPC52xx_PSC_SICR_ENAC97; + out_be32(&regs->sicr, psc_dma->sicr); + + /* No slots active */ + out_be32(&regs->ac97_slots, 0x00000000); + + /* AC97 clock is generated by the codec. + * Ensure that it starts ticking after codec reset. + */ + max_reset = 0; +reset: + if (max_reset++ > 5) { + dev_err(&op->dev, "AC97 codec failed to reset\n"); + mpc5200_audio_dma_destroy(op); + return -ENODEV; + } + + psc_ac97_cold_reset(&ac97); + psc_ac97_warm_reset(&ac97); + + /* first make sure it is low */ + timeout = 0; + while ((in_8(&regs->ipcr_acr.ipcr) & 0x80) != 0) { + udelay(1); + if (timeout++ > 1000) + goto reset; + } + /* then wait for the transition to high */ + timeout = 0; + while ((in_8(&regs->ipcr_acr.ipcr) & 0x80) == 0) { + udelay(1); + if (timeout++ > 1000) + psc_ac97_warm_reset(&ac97); + } + + /* Go */ + out_8(&regs->command, MPC52xx_PSC_TX_ENABLE | MPC52xx_PSC_RX_ENABLE); + + id1 = psc_ac97_read(&ac97, AC97_VENDOR_ID1); + id2 = psc_ac97_read(&ac97, AC97_VENDOR_ID2); + + dev_info(&op->dev, "Codec ID is %04x %04x\n", id1, id2); + + return 0; +} + +static int __devexit psc_ac97_of_remove(struct of_device *op) +{ + return mpc5200_audio_dma_destroy(op); +} + +/* Match table for of_platform binding */ +static struct of_device_id psc_ac97_match[] __devinitdata = { + { .compatible = "fsl,mpc5200-psc-ac97", }, + { .compatible = "fsl,mpc5200b-psc-ac97", }, + {} +}; +MODULE_DEVICE_TABLE(of, psc_ac97_match); + +static struct of_platform_driver psc_ac97_driver = { + .match_table = psc_ac97_match, + .probe = psc_ac97_of_probe, + .remove = __devexit_p(psc_ac97_of_remove), + .driver = { + .name = "mpc5200-psc-ac97", + .owner = THIS_MODULE, + }, +}; + +/* --------------------------------------------------------------------- + * Module setup and teardown; simply register the of_platform driver + * for the PSC in AC97 mode. + */ +static int __init psc_ac97_init(void) +{ + return of_register_platform_driver(&psc_ac97_driver); +} +module_init(psc_ac97_init); + +static void __exit psc_ac97_exit(void) +{ + of_unregister_platform_driver(&psc_ac97_driver); +} +module_exit(psc_ac97_exit); + +MODULE_AUTHOR("Jon Smirl <jonsmirl(a)gmail.com>"); +MODULE_DESCRIPTION("mpc5200 AC97 module"); +MODULE_LICENSE("GPL"); + diff --git a/sound/soc/fsl/mpc5200_psc_ac97.h b/sound/soc/fsl/mpc5200_psc_ac97.h new file mode 100644 index 0000000..4bc18c3 --- /dev/null +++ b/sound/soc/fsl/mpc5200_psc_ac97.h @@ -0,0 +1,15 @@ +/* + * Freescale MPC5200 PSC in AC97 mode + * ALSA SoC Digital Audio Interface (DAI) driver + * + */ + +#ifndef __SOUND_SOC_FSL_MPC52xx_PSC_AC97_H__ +#define __SOUND_SOC_FSL_MPC52xx_PSC_AC97_H__ + +extern struct snd_soc_dai psc_ac97_dai[]; + +#define MPC5200_AC97_NORMAL 0 +#define MPC5200_AC97_SPDIF 1 + +#endif /* __SOUND_SOC_FSL_MPC52xx_PSC_AC97_H__ */ ------------------------------ _______________________________________________ Alsa-devel mailing list Alsa-devel(a)alsa-project.org http://mailman.alsa-project.org/mailman/listinfo/alsa-devel End of Alsa-devel Digest, Vol 27, Issue 124 *******************************************

1 0

Re: [alsa-devel] Regarding Sound on Acer Aspire 6935G
by Karthik Ramgopal 23 May '09

23 May '09

Hi, Even after enabling DEBUG using --with-debug option with configure when compiling the alsa-driver snapshot leaves no more error messages in the dmesg logs. The only message relating to HDA is: [ 41.104817] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj. I just got the line-out output to work by toggling the surround volume. I still think it's a mapping problem. The headphone switch is turning the subwoofer on and off, and the surround volume is controlling the line-out volume. None of the line-in devices function and all of the amp-ins 0x0b to 0x0f are muted. Cannot find any verb to unmute them. hda-verb with SET_EAPD_BTLENABLE 2 at 0x15 is still needed at startup to fire up the amps. Please help. Regards, Karthik

3 21