March 2009 - Alsa-devel - mailman.alsa-project.org

[alsa-devel] PXA SSP - work in progress
by Mark Brown 13 Mar '09

13 Mar '09

I worked a bit on the PXA SSP code last night and was able to come up with a configuration which uses non-network mode for I2S and works well on the Zylonite. I'll post the current series I have in a followup to this, if you could take a look that'd be great - I haven't yet worked through all the testing I'd like to do. Unfortunately it's going to have broken Daniel's configuration since I inverted the sense of LRCLK as the chip seemed not to generate an LRCLK with a non-zero frame delay; I need to check to see if this is just something I've overlooked. Hopefully Daniel's system should just have inverted the left and right channels. Having worked through non-network mode my feeling is that we should be able to come up with something that can figure out the extra clock cycles needed for Daniel's configuration with less of a special case. Non-network mode does seem like a better default than network mode because it avoids needing to look at the TDM configuration unless you want to use that.

2 4

[alsa-devel] ASoC updates for 2.6.30
by Mark Brown 13 Mar '09

13 Mar '09

The following changes since commit 2a9f0ba7a976bc2b1bcf9156c1e57ffbc8f8fb64: Mark Brown (1): Merge branch 's3c-iis-header' into for-2.6.30 are available in the git repository at: git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6.git for-2.6.30 Lopez Cruz, Misael (1): ASoC: Move headset jack registration to device initialization for SDP3430 Mark Brown (1): ASoC: Move WM8580 to normal I2C device probe Philipp Zabel (1): ASoC: Replace remaining uses of snd_soc_cnew with snd_soc_add_controls. sound/soc/codecs/cs4270.c | 23 +-- sound/soc/codecs/tlv320aic26.c | 11 +- sound/soc/codecs/wm8400.c | 12 +- sound/soc/codecs/wm8580.c | 326 +++++++++++++++++------------------ sound/soc/codecs/wm8580.h | 5 - sound/soc/omap/n810.c | 12 +- sound/soc/omap/sdp3430.c | 74 +++++---- sound/soc/pxa/corgi.c | 12 +- sound/soc/pxa/palm27x.c | 13 +- sound/soc/pxa/poodle.c | 12 +- sound/soc/pxa/spitz.c | 12 +- sound/soc/pxa/tosa.c | 12 +- sound/soc/s3c24xx/neo1973_wm8753.c | 13 +- 13 files changed, 243 insertions(+), 294 deletions(-)

2 1

[alsa-devel] [PATCH] SoC: Move headset jack registration to device initialization for SDP3430
by Lopez Cruz, Misael 13 Mar '09

13 Mar '09

Move headset jack registration to the codec/machine specific initialization. Having the jack registration in machine init causes that the jack device gets initialized but not registered since the sound card is registered before the jack. Moving jack registration to device initialization will register the jack device along with all other devices associated to the card when the card is registed. As a consequence of jack device registered properly, the jack is detected as an input device. Signed-off-by: Misael Lopez Cruz <x0052729(a)ti.com> --- sound/soc/omap/sdp3430.c | 74 ++++++++++++++++++++++++--------------------- 1 files changed, 39 insertions(+), 35 deletions(-) diff --git a/sound/soc/omap/sdp3430.c b/sound/soc/omap/sdp3430.c index 715c648..0a41de6 100644 --- a/sound/soc/omap/sdp3430.c +++ b/sound/soc/omap/sdp3430.c @@ -39,6 +39,8 @@ #include "omap-pcm.h" #include "../codecs/twl4030.h" +static struct snd_soc_card snd_soc_sdp3430; + static int sdp3430_hw_params(struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params) { @@ -82,6 +84,27 @@ static struct snd_soc_ops sdp3430_ops = { .hw_params = sdp3430_hw_params, }; +/* Headset jack */ +static struct snd_soc_jack hs_jack; + +/* Headset jack detection DAPM pins */ +static struct snd_soc_jack_pin hs_jack_pins[] = { + { + .pin = "Headset Jack", + .mask = SND_JACK_HEADSET, + }, +}; + +/* Headset jack detection gpios */ +static struct snd_soc_jack_gpio hs_jack_gpios[] = { + { + .gpio = (OMAP_MAX_GPIO_LINES + 2), + .name = "hsdet-gpio", + .report = SND_JACK_HEADSET, + .debounce_time = 200, + }, +}; + /* SDP3430 machine DAPM */ static const struct snd_soc_dapm_widget sdp3430_twl4030_dapm_widgets[] = { SND_SOC_DAPM_MIC("Ext Mic", NULL), @@ -141,30 +164,25 @@ static int sdp3430_twl4030_init(struct snd_soc_codec *codec) snd_soc_dapm_nc_pin(codec, "CARKITR"); ret = snd_soc_dapm_sync(codec); + if (ret) + return ret; - return ret; -} + /* Headset jack detection */ + ret = snd_soc_jack_new(&snd_soc_sdp3430, "Headset Jack", + SND_JACK_HEADSET, &hs_jack); + if (ret) + return ret; -/* Headset jack */ -static struct snd_soc_jack hs_jack; + ret = snd_soc_jack_add_pins(&hs_jack, ARRAY_SIZE(hs_jack_pins), + hs_jack_pins); + if (ret) + return ret; -/* Headset jack detection DAPM pins */ -static struct snd_soc_jack_pin hs_jack_pins[] = { - { - .pin = "Headset Jack", - .mask = SND_JACK_HEADSET, - }, -}; + ret = snd_soc_jack_add_gpios(&hs_jack, ARRAY_SIZE(hs_jack_gpios), + hs_jack_gpios); -/* Headset jack detection gpios */ -static struct snd_soc_jack_gpio hs_jack_gpios[] = { - { - .gpio = (OMAP_MAX_GPIO_LINES + 2), - .name = "hsdet-gpio", - .report = SND_JACK_HEADSET, - .debounce_time = 200, - }, -}; + return ret; +} /* Digital audio interface glue - connects codec <--> CPU */ static struct snd_soc_dai_link sdp3430_dai = { @@ -216,21 +234,7 @@ static int __init sdp3430_soc_init(void) if (ret) goto err1; - /* Headset jack detection */ - ret = snd_soc_jack_new(&snd_soc_sdp3430, "SDP3430 headset jack", - SND_JACK_HEADSET, &hs_jack); - if (ret) - return ret; - - ret = snd_soc_jack_add_pins(&hs_jack, ARRAY_SIZE(hs_jack_pins), - hs_jack_pins); - if (ret) - return ret; - - ret = snd_soc_jack_add_gpios(&hs_jack, ARRAY_SIZE(hs_jack_gpios), - hs_jack_gpios); - - return ret; + return 0; err1: printk(KERN_ERR "Unable to add platform device\n"); -- 1.5.4.3

2 1

[alsa-devel] Audio problems with HP DV7-1025nr
by Jonathan Scruggs 13 Mar '09

13 Mar '09

Hi, I have tried many things to try to get my sound card to work, but no luck. At first with the when I started alsamixer, it would say that I have a generic sound card. My laptop has two audio interfaces: a nVidia HDMI and an IDT High Definition Codec. I read this mailing list and saw that many people had issues with the HP's version of the IDT sound card. Then someone added patches to fix an issue with DV4. The fixes were in the latest snapshots, so I did some searching and pulled the alsa sources from here: git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6.git since I am using the 2.6.28 kernel. I went through the code and confirmed that it was updated to what I saw in the patches and the patches were not compatible with the kernel source I have, hence I was looking for something more compatible. More specifically, the kernel I have is "2.6.28-gentoo-r2 #5 SMP Wed Feb 25 15:37:22 GMT 2009 x86_64 Intel(R) Core(TM)2 Duo CPU P8400 @ 2.26GHz Genuine Intel GNU/Linux". With a little bit of work, I merged in the new alsa source with that kernel and recompiled. Things are detected a bit better, like now alsamixer is saying that I have the chip "Nvidia MCP78 HDMI" instead of a Generic one. However, this is not the chip I want. I want to output to my speakers and headphone ports. I tried setting the option "model=hp-dv5" and then "model=hp-dv7" but that does nothing. I have absolutely no sound at all out of my speakers or headphone port. The drivers for this soundcard are on the HP website if you need them. Also, I tried removing the nvidia option from the list in the kernel configuration and only have IDT selected, but it would say unknow nvidia chip when trying to load the module on boot. I have the output of lspci -nv attached to this email. I hope you can give me a clue as to what to do next. This is what I have in my in my /etc/modprobe.d/alsa file: # Alsa kernel modules' configuration file. # ALSA portion alias char-major-116 snd # OSS/Free portion alias char-major-14 soundcore # OSS/Free portion - card #1 alias sound-service-0-0 snd-mixer-oss alias sound-service-0-1 snd-seq-oss alias sound-service-0-3 snd-pcm-oss alias sound-service-0-8 snd-seq-oss alias sound-service-0-12 snd-pcm-oss alias /dev/mixer snd-mixer-oss alias /dev/dsp snd-pcm-oss alias /dev/midi snd-seq-oss # Set this to the correct number of cards. options snd cards_limit=1 alias snd-card-0 snd-hda-intel options snd-hda-intel model=hp-dv7 enable=1 enable_msi=1 single_cmd=0 power_save_controller=0 power_save=0 I have a program that analyzed my audio in Windows. This is the output from that: Sound, video and game controllers || NVIDIA HDMI Audio Top Property Value NVIDIA HDMI Audio Device ID HDAUDIO\FUNC_01VEN_10DEDEV_0006SUBSYS_10DE0101REV_1000\43451138D00201 Status 0x0180200a Started Problem 0x00000000 (0) Service NVHDA Capabilities 0x00000000 Config Flags 0x00000000 Class MEDIA Manufacturer NVIDIA Hardware IDs HDAUDIO\FUNC_01VEN_10DEDEV_0006SUBSYS_10DE0101REV_1000 HDAUDIO\FUNC_01VEN_10DEDEV_0006SUBSYS_10DE0101 Compatible IDs HDAUDIO\FUNC_01CTLR_VEN_8086CTLR_DEV_293EVEN_10DEDEV_0006REV_1000 HDAUDIO\FUNC_01CTLR_VEN_8086VEN_10DEDEV_0006REV_1000 HDAUDIO\FUNC_01VEN_10DEDEV_0006REV_1000 HDAUDIO\FUNC_01CTLR_VEN_8086CTLR_DEV_293EVEN_10DEDEV_0006 HDAUDIO\FUNC_01CTLR_VEN_8086VEN_10DEDEV_0006 HDAUDIO\FUNC_01VEN_10DEDEV_0006 HDAUDIO\FUNC_01CTLR_VEN_8086CTLR_DEV_293EVEN_10DE HDAUDIO\FUNC_01CTLR_VEN_8086VEN_10DE HDAUDIO\FUNC_01VEN_10DE HDAUDIO\FUNC_01CTLR_VEN_8086CTLR_DEV_293E HDAUDIO\FUNC_01CTLR_VEN_8086 HDAUDIO\FUNC_01GFVEN_10DEDEV_0006SUBSYS_10DE0101REV_1000 HDAUDIO\FUNC_01 Class GUID {4d36e96c-e325-11ce-bfc1-08002be10318} Location Internal High Definition Audio Bus Bus number 0x00000000 Enumerator name HDAUDIO Description NVIDIA HDMI Audio Driver {4d36e96c-e325-11ce-bfc1-08002be10318}\0000 Physical Object Name \Device\0000008b UI number 0x00000002 Bustype GUID {41203534-2037-3144-2042-422044362041} Legacy bus type 0x00000005 Device Type 0x0000001d Install State 0x00000000 Security 01 00 04 90 00 00 00 00 00 00 00 00 00 00 00 00 14 00 00 00 02 00 5C 00 04 00 00 00 00 00 14 00 00 00 00 10 01 01 00 00 00 00 00 05 12 00 00 00 00 00 18 00 00 00 00 E0 01 02 00 00 00 00 00 05 20 00 00 00 20 02 00 00 00 00 14 00 00 00 00 E0 01 01 00 00 00 00 00 01 00 00 00 00 00 00 14 00 00 00 00 E0 01 01 00 00 00 00 00 05 0C 00 00 00 Security (SDS form) D:P(A;;GA;;;SY)(A;;GXGWGR;;;BA)(A;;GXGWGR;;;WD)(A;;GXGWGR;;;RC) Device Address 0x00000201 Sound, video and game controllers || IDT High Definition Audio CODEC Top Property Value IDT High Definition Audio CODEC Device ID HDAUDIO\FUNC_01VEN_111DDEV_76B2SUBSYS_103C30F4REV_1003\43451138D00001 Status 0x0180200a Started Problem 0x00000000 (0) Service STHDA Capabilities 0x00000000 Config Flags 0x00000000 Class MEDIA Manufacturer IDT Hardware IDs HDAUDIO\FUNC_01VEN_111DDEV_76B2SUBSYS_103C30F4REV_1003 HDAUDIO\FUNC_01VEN_111DDEV_76B2SUBSYS_103C30F4 Compatible IDs HDAUDIO\FUNC_01CTLR_VEN_8086CTLR_DEV_293EVEN_111DDEV_76B2REV_1003 HDAUDIO\FUNC_01CTLR_VEN_8086VEN_111DDEV_76B2REV_1003 HDAUDIO\FUNC_01VEN_111DDEV_76B2REV_1003 HDAUDIO\FUNC_01CTLR_VEN_8086CTLR_DEV_293EVEN_111DDEV_76B2 HDAUDIO\FUNC_01CTLR_VEN_8086VEN_111DDEV_76B2 HDAUDIO\FUNC_01VEN_111DDEV_76B2 HDAUDIO\FUNC_01CTLR_VEN_8086CTLR_DEV_293EVEN_111D HDAUDIO\FUNC_01CTLR_VEN_8086VEN_111D HDAUDIO\FUNC_01VEN_111D HDAUDIO\FUNC_01CTLR_VEN_8086CTLR_DEV_293E HDAUDIO\FUNC_01CTLR_VEN_8086 HDAUDIO\FUNC_01GFVEN_111DDEV_76B2SUBSYS_103C30F4REV_1003 HDAUDIO\FUNC_01 Class GUID {4d36e96c-e325-11ce-bfc1-08002be10318} Location Internal High Definition Audio Bus Bus number 0x00000000 Enumerator name HDAUDIO Description IDT High Definition Audio CODEC Friendly name IDT High Definition Audio CODEC Driver {4d36e96c-e325-11ce-bfc1-08002be10318}\0007 Physical Object Name \Device\00000089 UI number 0x00000000 Bustype GUID {41203534-2037-3144-2042-422044362041} Legacy bus type 0x00000005 Device Type 0x0000001d Install State 0x00000000 Security 01 00 04 90 00 00 00 00 00 00 00 00 00 00 00 00 14 00 00 00 02 00 5C 00 04 00 00 00 00 00 14 00 00 00 00 10 01 01 00 00 00 00 00 05 12 00 00 00 00 00 18 00 00 00 00 E0 01 02 00 00 00 00 00 05 20 00 00 00 20 02 00 00 00 00 14 00 00 00 00 E0 01 01 00 00 00 00 00 01 00 00 00 00 00 00 14 00 00 00 00 E0 01 01 00 00 00 00 00 05 0C 00 00 00 Security (SDS form) D:P(A;;GA;;;SY)(A;;GXGWGR;;;BA)(A;;GXGWGR;;;WD)(A;;GXGWGR;;;RC) Device Address 0x00000001 Thanks, Jon

2 1

[alsa-devel] multiple USB soundcards crashes, please help
by Giovanni Maruzzelli 13 Mar '09

13 Mar '09

Dear ALSA developers, my application needs to use multiple USB soundcards (based on standard cm-108 chipset) for I/O. Seems to me that with recent kernels (after 2.6.21) this is almost impossible: -if you use uhci_hcd it crashes with 4 running soundcards (cannot submit datapipe: not enough bandwidth) -if you use ehci_hcd it crashes way before (device resets) With older kernels, at least uhci_hcd seems to work. This maybe is related to the reworking of the bandwidth management into the uhci_hcd introduced in 2.6.21. I'm available to and I would be glad to help you ALSA developers with all the information possible: just tell me wich infos you need and I'll gather all the infos for you. You can test the problem with: arecord -Dplughw:0 | aplay plughw:0 & arecord -Dplughw:1 | aplay plughw:1 & arecord -Dplughw:2 | aplay plughw:2 & arecord -Dplughw:3 | aplay plughw:3 &

2 2

[alsa-devel] How can PCI resource allocation fail?
by Christian P. Schmidt 13 Mar '09

13 Mar '09

Hi all, I'm toying with the alsa-driver for the Creative Labs X-Fi. I'm working on the PCI Express version of this card, though, which is the same as the PCI version plus a PCIe to PCI bridge but has a different ID: +-1c.2-[0000:03-04]----00.0-[0000:04]----00.0 1102:0009 03:00.0 PCI bridge: Creative Labs Device 7006 04:00.0 Audio device: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG Now, after adding the ID, the driver fails: [46833.487579] CA0106 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [46833.487586] CA0106 0000:04:00.0: PCI INT A disabled [46833.487588] cannot allocate the port [46833.487594] CA0106: probe of 0000:04:00.0 failed with error -16 The actual error is occurring in chip->port = pci_resource_start(pci, 0); chip->res_port = request_region(chip->port, pci_resource_len(pci,0), "snd_ca0106"); if (!chip->res_port) { snd_ca0106_free(chip); printk(KERN_ERR "cannot allocate the port\n"); return -EBUSY; } This from /proc/iomem: f9f00000-f9ffffff : PCI Bus 0000:03 f9f00000-f9ffffff : PCI Bus 0000:04 f9ffc000-f9ffffff : 0000:04:00.0 Some additional debug output tells me that the code is actually trying to allocate 16k starting from f9ffc000. What could be potential reasons for the failure? Do I have to do something with the bridge before I can try to request the region? Regards, Christian PS: lcpci -vv output afterwards, can't see anything special here. 03:00.0 PCI bridge: Creative Labs Device 7006 (prog-if 00 [Normal decode]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=03, secondary=04, subordinate=04, sec-latency=64 Memory behind bridge: f9f00000-f9ffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [60] MSI: Mask- 64bit+ Count=1/16 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [80] Subsystem: Creative Labs Device 0010 Capabilities: [90] Express (v1) PCI/PCI-X Bridge, MSI 00 DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn- 04:00.0 Audio device: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG Subsystem: Creative Labs Device 0018 Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 18 Region 0: Memory at f9ffc000 (32-bit, non-prefetchable) [size=16K] Capabilities: [dc] Power Management version 3 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel modules: snd-ca0106

5 4

[alsa-devel] [PATCH] ALSA: drop outdated and broken sa11xx-uda1341 driver
by Dmitry Artamonow 13 Mar '09

13 Mar '09

It depends on L3 support from 2.4 kernel (CONFIG_L3) that never got merged into mainline. Since there's no way to use it on any of supported machines (iPaq h3100 or h3600), better drop it for now. It can be reimplemented later using ASoC infrastructure (there's already a driver for uda1341 codec in mainline, so only CPU and machine parts need to be written). Signed-off-by: Dmitry Artamonow <mad_soft(a)inbox.ru> Cc: Russell King <linux(a)arm.linux.org.uk> --- include/sound/uda1341.h | 126 ------ sound/arm/Kconfig | 11 - sound/arm/Makefile | 3 - sound/arm/sa11xx-uda1341.c | 983 -------------------------------------------- sound/i2c/Makefile | 2 - sound/i2c/l3/Makefile | 8 - sound/i2c/l3/uda1341.c | 935 ----------------------------------------- 7 files changed, 0 insertions(+), 2068 deletions(-) delete mode 100644 include/sound/uda1341.h delete mode 100644 sound/arm/sa11xx-uda1341.c delete mode 100644 sound/i2c/l3/Makefile delete mode 100644 sound/i2c/l3/uda1341.c diff --git a/include/sound/uda1341.h b/include/sound/uda1341.h deleted file mode 100644 index 110d5dc..0000000 --- a/include/sound/uda1341.h +++ /dev/null @@ -1,126 +0,0 @@ -/* - * linux/include/linux/l3/uda1341.h - * - * Philips UDA1341 mixer device driver for ALSA - * - * Copyright (c) 2002 Tomas Kasparek <tomas.kasparek(a)seznam.cz> - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License. - * - * History: - * - * 2002-03-13 Tomas Kasparek Initial release - based on uda1341.h from OSS - * 2002-03-30 Tomas Kasparek Proc filesystem support, complete mixer and DSP - * features support - */ - -#define UDA1341_ALSA_NAME "snd-uda1341" - -/* - * Default rate set after inicialization - */ -#define AUDIO_RATE_DEFAULT 44100 - -/* - * UDA1341 L3 address and command types - */ -#define UDA1341_L3ADDR 5 -#define UDA1341_DATA0 (UDA1341_L3ADDR << 2 | 0) -#define UDA1341_DATA1 (UDA1341_L3ADDR << 2 | 1) -#define UDA1341_STATUS (UDA1341_L3ADDR << 2 | 2) - -enum uda1341_onoff { - OFF=0, - ON, -}; - -enum uda1341_format { - I2S=0, - LSB16, - LSB18, - LSB20, - MSB, - LSB16MSB, - LSB18MSB, - LSB20MSB, -}; - -enum uda1341_fs { - F512=0, - F384, - F256, - Funused, -}; - -enum uda1341_peak { - BEFORE=0, - AFTER, -}; - -enum uda1341_filter { - FLAT=0, - MIN, - MIN2, - MAX, -}; - -enum uda1341_mixer { - DOUBLE, - LINE, - MIC, - MIXER, -}; - -enum uda1341_deemp { - NONE, - D32, - D44, - D48, -}; - -enum uda1341_config { - CMD_READ_REG = 0, - CMD_RESET, - CMD_FS, - CMD_FORMAT, - CMD_OGAIN, - CMD_IGAIN, - CMD_DAC, - CMD_ADC, - CMD_VOLUME, - CMD_BASS, - CMD_TREBBLE, - CMD_PEAK, - CMD_DEEMP, - CMD_MUTE, - CMD_FILTER, - CMD_CH1, - CMD_CH2, - CMD_MIC, - CMD_MIXER, - CMD_AGC, - CMD_IG, - CMD_AGC_TIME, - CMD_AGC_LEVEL, -#ifdef CONFIG_PM - CMD_SUSPEND, - CMD_RESUME, -#endif - CMD_LAST, -}; - -enum write_through { - //used in update_bits (write_cfg) to avoid l3_write - just update local copy of regs. - REGS_ONLY=0, - //update local regs and write value to uda1341 - do l3_write - FLUSH, -}; - -int __init snd_chip_uda1341_mixer_new(struct snd_card *card, struct l3_client **clnt); - -/* - * Local variables: - * indent-tabs-mode: t - * End: - */ diff --git a/sound/arm/Kconfig b/sound/arm/Kconfig index f8e6de4..885683a 100644 --- a/sound/arm/Kconfig +++ b/sound/arm/Kconfig @@ -11,17 +11,6 @@ menuconfig SND_ARM if SND_ARM -config SND_SA11XX_UDA1341 - tristate "SA11xx UDA1341TS driver (iPaq H3600)" - depends on ARCH_SA1100 && L3 - select SND_PCM - help - Say Y here if you have a Compaq iPaq H3x00 handheld computer - and want to use its Philips UDA 1341 audio chip. - - To compile this driver as a module, choose M here: the module - will be called snd-sa11xx-uda1341. - config SND_ARMAACI tristate "ARM PrimeCell PL041 AC Link support" depends on ARM_AMBA diff --git a/sound/arm/Makefile b/sound/arm/Makefile index 2054de1..5a549ed 100644 --- a/sound/arm/Makefile +++ b/sound/arm/Makefile @@ -2,9 +2,6 @@ # Makefile for ALSA # -obj-$(CONFIG_SND_SA11XX_UDA1341) += snd-sa11xx-uda1341.o -snd-sa11xx-uda1341-objs := sa11xx-uda1341.o - obj-$(CONFIG_SND_ARMAACI) += snd-aaci.o snd-aaci-objs := aaci.o devdma.o diff --git a/sound/arm/sa11xx-uda1341.c b/sound/arm/sa11xx-uda1341.c deleted file mode 100644 index 1dcd51d..0000000 --- a/sound/arm/sa11xx-uda1341.c +++ /dev/null @@ -1,983 +0,0 @@ -/* - * Driver for Philips UDA1341TS on Compaq iPAQ H3600 soundcard - * Copyright (C) 2002 Tomas Kasparek <tomas.kasparek(a)seznam.cz> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License. - * - * History: - * - * 2002-03-13 Tomas Kasparek initial release - based on h3600-uda1341.c from OSS - * 2002-03-20 Tomas Kasparek playback over ALSA is working - * 2002-03-28 Tomas Kasparek playback over OSS emulation is working - * 2002-03-29 Tomas Kasparek basic capture is working (native ALSA) - * 2002-03-29 Tomas Kasparek capture is working (OSS emulation) - * 2002-04-04 Tomas Kasparek better rates handling (allow non-standard rates) - * 2003-02-14 Brian Avery fixed full duplex mode, other updates - * 2003-02-20 Tomas Kasparek merged updates by Brian (except HAL) - * 2003-04-19 Jaroslav Kysela recoded DMA stuff to follow 2.4.18rmk3-hh24 kernel - * working suspend and resume - * 2003-04-28 Tomas Kasparek updated work by Jaroslav to compile it under 2.5.x again - * merged HAL layer (patches from Brian) - */ - -/*************************************************************************************************** -* -* To understand what Alsa Drivers should be doing look at "Writing an Alsa Driver" by Takashi Iwai -* available in the Alsa doc section on the website -* -* A few notes to make things clearer. The UDA1341 is hooked up to Serial port 4 on the SA1100. -* We are using SSP mode to talk to the UDA1341. The UDA1341 bit & wordselect clocks are generated -* by this UART. Unfortunately, the clock only runs if the transmit buffer has something in it. -* So, if we are just recording, we feed the transmit DMA stream a bunch of 0x0000 so that the -* transmit buffer is full and the clock keeps going. The zeroes come from FLUSH_BASE_PHYS which -* is a mem loc that always decodes to 0's w/ no off chip access. -* -* Some alsa terminology: -* frame => num_channels * sample_size e.g stereo 16 bit is 2 * 16 = 32 bytes -* period => the least number of bytes that will generate an interrupt e.g. we have a 1024 byte -* buffer and 4 periods in the runtime structure this means we'll get an int every 256 -* bytes or 4 times per buffer. -* A number of the sizes are in frames rather than bytes, use frames_to_bytes and -* bytes_to_frames to convert. The easiest way to tell the units is to look at the -* type i.e. runtime-> buffer_size is in frames and its type is snd_pcm_uframes_t -* -* Notes about the pointer fxn: -* The pointer fxn needs to return the offset into the dma buffer in frames. -* Interrupts must be blocked before calling the dma_get_pos fxn to avoid race with interrupts. -* -* Notes about pause/resume -* Implementing this would be complicated so it's skipped. The problem case is: -* A full duplex connection is going, then play is paused. At this point you need to start xmitting -* 0's to keep the record active which means you cant just freeze the dma and resume it later you'd -* need to save off the dma info, and restore it properly on a resume. Yeach! -* -* Notes about transfer methods: -* The async write calls fail. I probably need to implement something else to support them? -* -***************************************************************************************************/ - -#include <linux/module.h> -#include <linux/moduleparam.h> -#include <linux/init.h> -#include <linux/err.h> -#include <linux/platform_device.h> -#include <linux/errno.h> -#include <linux/ioctl.h> -#include <linux/delay.h> -#include <linux/slab.h> - -#ifdef CONFIG_PM -#include <linux/pm.h> -#endif - -#include <mach/hardware.h> -#include <mach/h3600.h> -#include <asm/mach-types.h> -#include <asm/dma.h> - -#include <sound/core.h> -#include <sound/pcm.h> -#include <sound/initval.h> - -#include <linux/l3/l3.h> - -#undef DEBUG_MODE -#undef DEBUG_FUNCTION_NAMES -#include <sound/uda1341.h> - -/* - * FIXME: Is this enough as autodetection of 2.4.X-rmkY-hhZ kernels? - * We use DMA stuff from 2.4.18-rmk3-hh24 here to be able to compile this - * module for Familiar 0.6.1 - */ - -/* {{{ Type definitions */ - -MODULE_AUTHOR("Tomas Kasparek <tomas.kasparek(a)seznam.cz>"); -MODULE_LICENSE("GPL"); -MODULE_DESCRIPTION("SA1100/SA1111 + UDA1341TS driver for ALSA"); -MODULE_SUPPORTED_DEVICE("{{UDA1341,iPAQ H3600 UDA1341TS}}"); - -static char *id; /* ID for this card */ - -module_param(id, charp, 0444); -MODULE_PARM_DESC(id, "ID string for SA1100/SA1111 + UDA1341TS soundcard."); - -struct audio_stream { - char *id; /* identification string */ - int stream_id; /* numeric identification */ - dma_device_t dma_dev; /* device identifier for DMA */ -#ifdef HH_VERSION - dmach_t dmach; /* dma channel identification */ -#else - dma_regs_t *dma_regs; /* points to our DMA registers */ -#endif - unsigned int active:1; /* we are using this stream for transfer now */ - int period; /* current transfer period */ - int periods; /* current count of periods registerd in the DMA engine */ - int tx_spin; /* are we recoding - flag used to do DMA trans. for sync */ - unsigned int old_offset; - spinlock_t dma_lock; /* for locking in DMA operations (see dma-sa1100.c in the kernel) */ - struct snd_pcm_substream *stream; -}; - -struct sa11xx_uda1341 { - struct snd_card *card; - struct l3_client *uda1341; - struct snd_pcm *pcm; - long samplerate; - struct audio_stream s[2]; /* playback & capture */ -}; - -static unsigned int rates[] = { - 8000, 10666, 10985, 14647, - 16000, 21970, 22050, 24000, - 29400, 32000, 44100, 48000, -}; - -static struct snd_pcm_hw_constraint_list hw_constraints_rates = { - .count = ARRAY_SIZE(rates), - .list = rates, - .mask = 0, -}; - -static struct platform_device *device; - -/* }}} */ - -/* {{{ Clock and sample rate stuff */ - -/* - * Stop-gap solution until rest of hh.org HAL stuff is merged. - */ -#define GPIO_H3600_CLK_SET0 GPIO_GPIO (12) -#define GPIO_H3600_CLK_SET1 GPIO_GPIO (13) - -#ifdef CONFIG_SA1100_H3XXX -#define clr_sa11xx_uda1341_egpio(x) clr_h3600_egpio(x) -#define set_sa11xx_uda1341_egpio(x) set_h3600_egpio(x) -#else -#error This driver could serve H3x00 handhelds only! -#endif - -static void sa11xx_uda1341_set_audio_clock(long val) -{ - switch (val) { - case 24000: case 32000: case 48000: /* 00: 12.288 MHz */ - GPCR = GPIO_H3600_CLK_SET0 | GPIO_H3600_CLK_SET1; - break; - - case 22050: case 29400: case 44100: /* 01: 11.2896 MHz */ - GPSR = GPIO_H3600_CLK_SET0; - GPCR = GPIO_H3600_CLK_SET1; - break; - - case 8000: case 10666: case 16000: /* 10: 4.096 MHz */ - GPCR = GPIO_H3600_CLK_SET0; - GPSR = GPIO_H3600_CLK_SET1; - break; - - case 10985: case 14647: case 21970: /* 11: 5.6245 MHz */ - GPSR = GPIO_H3600_CLK_SET0 | GPIO_H3600_CLK_SET1; - break; - } -} - -static void sa11xx_uda1341_set_samplerate(struct sa11xx_uda1341 *sa11xx_uda1341, long rate) -{ - int clk_div = 0; - int clk=0; - - /* We don't want to mess with clocks when frames are in flight */ - Ser4SSCR0 &= ~SSCR0_SSE; - /* wait for any frame to complete */ - udelay(125); - - /* - * We have the following clock sources: - * 4.096 MHz, 5.6245 MHz, 11.2896 MHz, 12.288 MHz - * Those can be divided either by 256, 384 or 512. - * This makes up 12 combinations for the following samplerates... - */ - if (rate >= 48000) - rate = 48000; - else if (rate >= 44100) - rate = 44100; - else if (rate >= 32000) - rate = 32000; - else if (rate >= 29400) - rate = 29400; - else if (rate >= 24000) - rate = 24000; - else if (rate >= 22050) - rate = 22050; - else if (rate >= 21970) - rate = 21970; - else if (rate >= 16000) - rate = 16000; - else if (rate >= 14647) - rate = 14647; - else if (rate >= 10985) - rate = 10985; - else if (rate >= 10666) - rate = 10666; - else - rate = 8000; - - /* Set the external clock generator */ - - sa11xx_uda1341_set_audio_clock(rate); - - /* Select the clock divisor */ - switch (rate) { - case 8000: - case 10985: - case 22050: - case 24000: - clk = F512; - clk_div = SSCR0_SerClkDiv(16); - break; - case 16000: - case 21970: - case 44100: - case 48000: - clk = F256; - clk_div = SSCR0_SerClkDiv(8); - break; - case 10666: - case 14647: - case 29400: - case 32000: - clk = F384; - clk_div = SSCR0_SerClkDiv(12); - break; - } - - /* FMT setting should be moved away when other FMTs are added (FIXME) */ - l3_command(sa11xx_uda1341->uda1341, CMD_FORMAT, (void *)LSB16); - - l3_command(sa11xx_uda1341->uda1341, CMD_FS, (void *)clk); - Ser4SSCR0 = (Ser4SSCR0 & ~0xff00) + clk_div + SSCR0_SSE; - sa11xx_uda1341->samplerate = rate; -} - -/* }}} */ - -/* {{{ HW init and shutdown */ - -static void sa11xx_uda1341_audio_init(struct sa11xx_uda1341 *sa11xx_uda1341) -{ - unsigned long flags; - - /* Setup DMA stuff */ - sa11xx_uda1341->s[SNDRV_PCM_STREAM_PLAYBACK].id = "UDA1341 out"; - sa11xx_uda1341->s[SNDRV_PCM_STREAM_PLAYBACK].stream_id = SNDRV_PCM_STREAM_PLAYBACK; - sa11xx_uda1341->s[SNDRV_PCM_STREAM_PLAYBACK].dma_dev = DMA_Ser4SSPWr; - - sa11xx_uda1341->s[SNDRV_PCM_STREAM_CAPTURE].id = "UDA1341 in"; - sa11xx_uda1341->s[SNDRV_PCM_STREAM_CAPTURE].stream_id = SNDRV_PCM_STREAM_CAPTURE; - sa11xx_uda1341->s[SNDRV_PCM_STREAM_CAPTURE].dma_dev = DMA_Ser4SSPRd; - - /* Initialize the UDA1341 internal state */ - - /* Setup the uarts */ - local_irq_save(flags); - GAFR |= (GPIO_SSP_CLK); - GPDR &= ~(GPIO_SSP_CLK); - Ser4SSCR0 = 0; - Ser4SSCR0 = SSCR0_DataSize(16) + SSCR0_TI + SSCR0_SerClkDiv(8); - Ser4SSCR1 = SSCR1_SClkIactL + SSCR1_SClk1P + SSCR1_ExtClk; - Ser4SSCR0 |= SSCR0_SSE; - local_irq_restore(flags); - - /* Enable the audio power */ - - clr_sa11xx_uda1341_egpio(IPAQ_EGPIO_CODEC_NRESET); - set_sa11xx_uda1341_egpio(IPAQ_EGPIO_AUDIO_ON); - set_sa11xx_uda1341_egpio(IPAQ_EGPIO_QMUTE); - - /* Wait for the UDA1341 to wake up */ - mdelay(1); //FIXME - was removed by Perex - Why? - - /* Initialize the UDA1341 internal state */ - l3_open(sa11xx_uda1341->uda1341); - - /* external clock configuration (after l3_open - regs must be initialized */ - sa11xx_uda1341_set_samplerate(sa11xx_uda1341, sa11xx_uda1341->samplerate); - - /* Wait for the UDA1341 to wake up */ - set_sa11xx_uda1341_egpio(IPAQ_EGPIO_CODEC_NRESET); - mdelay(1); - - /* make the left and right channels unswapped (flip the WS latch) */ - Ser4SSDR = 0; - - clr_sa11xx_uda1341_egpio(IPAQ_EGPIO_QMUTE); -} - -static void sa11xx_uda1341_audio_shutdown(struct sa11xx_uda1341 *sa11xx_uda1341) -{ - /* mute on */ - set_sa11xx_uda1341_egpio(IPAQ_EGPIO_QMUTE); - - /* disable the audio power and all signals leading to the audio chip */ - l3_close(sa11xx_uda1341->uda1341); - Ser4SSCR0 = 0; - clr_sa11xx_uda1341_egpio(IPAQ_EGPIO_CODEC_NRESET); - - /* power off and mute off */ - /* FIXME - is muting off necesary??? */ - - clr_sa11xx_uda1341_egpio(IPAQ_EGPIO_AUDIO_ON); - clr_sa11xx_uda1341_egpio(IPAQ_EGPIO_QMUTE); -} - -/* }}} */ - -/* {{{ DMA staff */ - -/* - * these are the address and sizes used to fill the xmit buffer - * so we can get a clock in record only mode - */ -#define FORCE_CLOCK_ADDR (dma_addr_t)FLUSH_BASE_PHYS -#define FORCE_CLOCK_SIZE 4096 // was 2048 - -// FIXME Why this value exactly - wrote comment -#define DMA_BUF_SIZE 8176 /* <= MAX_DMA_SIZE from asm/arch-sa1100/dma.h */ - -#ifdef HH_VERSION - -static int audio_dma_request(struct audio_stream *s, void (*callback)(void *, int)) -{ - int ret; - - ret = sa1100_request_dma(&s->dmach, s->id, s->dma_dev); - if (ret < 0) { - printk(KERN_ERR "unable to grab audio dma 0x%x\n", s->dma_dev); - return ret; - } - sa1100_dma_set_callback(s->dmach, callback); - return 0; -} - -static inline void audio_dma_free(struct audio_stream *s) -{ - sa1100_free_dma(s->dmach); - s->dmach = -1; -} - -#else - -static int audio_dma_request(struct audio_stream *s, void (*callback)(void *)) -{ - int ret; - - ret = sa1100_request_dma(s->dma_dev, s->id, callback, s, &s->dma_regs); - if (ret < 0) - printk(KERN_ERR "unable to grab audio dma 0x%x\n", s->dma_dev); - return ret; -} - -static void audio_dma_free(struct audio_stream *s) -{ - sa1100_free_dma(s->dma_regs); - s->dma_regs = 0; -} - -#endif - -static u_int audio_get_dma_pos(struct audio_stream *s) -{ - struct snd_pcm_substream *substream = s->stream; - struct snd_pcm_runtime *runtime = substream->runtime; - unsigned int offset; - unsigned long flags; - dma_addr_t addr; - - // this must be called w/ interrupts locked out see dma-sa1100.c in the kernel - spin_lock_irqsave(&s->dma_lock, flags); -#ifdef HH_VERSION - sa1100_dma_get_current(s->dmach, NULL, &addr); -#else - addr = sa1100_get_dma_pos((s)->dma_regs); -#endif - offset = addr - runtime->dma_addr; - spin_unlock_irqrestore(&s->dma_lock, flags); - - offset = bytes_to_frames(runtime,offset); - if (offset >= runtime->buffer_size) - offset = 0; - - return offset; -} - -/* - * this stops the dma and clears the dma ptrs - */ -static void audio_stop_dma(struct audio_stream *s) -{ - unsigned long flags; - - spin_lock_irqsave(&s->dma_lock, flags); - s->active = 0; - s->period = 0; - /* this stops the dma channel and clears the buffer ptrs */ -#ifdef HH_VERSION - sa1100_dma_flush_all(s->dmach); -#else - sa1100_clear_dma(s->dma_regs); -#endif - spin_unlock_irqrestore(&s->dma_lock, flags); -} - -static void audio_process_dma(struct audio_stream *s) -{ - struct snd_pcm_substream *substream = s->stream; - struct snd_pcm_runtime *runtime; - unsigned int dma_size; - unsigned int offset; - int ret; - - /* we are requested to process synchronization DMA transfer */ - if (s->tx_spin) { - if (snd_BUG_ON(s->stream_id != SNDRV_PCM_STREAM_PLAYBACK)) - return; - /* fill the xmit dma buffers and return */ -#ifdef HH_VERSION - sa1100_dma_set_spin(s->dmach, FORCE_CLOCK_ADDR, FORCE_CLOCK_SIZE); -#else - while (1) { - ret = sa1100_start_dma(s->dma_regs, FORCE_CLOCK_ADDR, FORCE_CLOCK_SIZE); - if (ret) - return; - } -#endif - return; - } - - /* must be set here - only valid for running streams, not for forced_clock dma fills */ - runtime = substream->runtime; - while (s->active && s->periods < runtime->periods) { - dma_size = frames_to_bytes(runtime, runtime->period_size); - if (s->old_offset) { - /* a little trick, we need resume from old position */ - offset = frames_to_bytes(runtime, s->old_offset - 1); - s->old_offset = 0; - s->periods = 0; - s->period = offset / dma_size; - offset %= dma_size; - dma_size = dma_size - offset; - if (!dma_size) - continue; /* special case */ - } else { - offset = dma_size * s->period; - snd_BUG_ON(dma_size > DMA_BUF_SIZE); - } -#ifdef HH_VERSION - ret = sa1100_dma_queue_buffer(s->dmach, s, runtime->dma_addr + offset, dma_size); - if (ret) - return; //FIXME -#else - ret = sa1100_start_dma((s)->dma_regs, runtime->dma_addr + offset, dma_size); - if (ret) { - printk(KERN_ERR "audio_process_dma: cannot queue DMA buffer (%i)\n", ret); - return; - } -#endif - - s->period++; - s->period %= runtime->periods; - s->periods++; - } -} - -#ifdef HH_VERSION -static void audio_dma_callback(void *data, int size) -#else -static void audio_dma_callback(void *data) -#endif -{ - struct audio_stream *s = data; - - /* - * If we are getting a callback for an active stream then we inform - * the PCM middle layer we've finished a period - */ - if (s->active) - snd_pcm_period_elapsed(s->stream); - - spin_lock(&s->dma_lock); - if (!s->tx_spin && s->periods > 0) - s->periods--; - audio_process_dma(s); - spin_unlock(&s->dma_lock); -} - -/* }}} */ - -/* {{{ PCM setting */ - -/* {{{ trigger & timer */ - -static int snd_sa11xx_uda1341_trigger(struct snd_pcm_substream *substream, int cmd) -{ - struct sa11xx_uda1341 *chip = snd_pcm_substream_chip(substream); - int stream_id = substream->pstr->stream; - struct audio_stream *s = &chip->s[stream_id]; - struct audio_stream *s1 = &chip->s[stream_id ^ 1]; - int err = 0; - - /* note local interrupts are already disabled in the midlevel code */ - spin_lock(&s->dma_lock); - switch (cmd) { - case SNDRV_PCM_TRIGGER_START: - /* now we need to make sure a record only stream has a clock */ - if (stream_id == SNDRV_PCM_STREAM_CAPTURE && !s1->active) { - /* we need to force fill the xmit DMA with zeros */ - s1->tx_spin = 1; - audio_process_dma(s1); - } - /* this case is when you were recording then you turn on a - * playback stream so we stop (also clears it) the dma first, - * clear the sync flag and then we let it turned on - */ - else { - s->tx_spin = 0; - } - - /* requested stream startup */ - s->active = 1; - audio_process_dma(s); - break; - case SNDRV_PCM_TRIGGER_STOP: - /* requested stream shutdown */ - audio_stop_dma(s); - - /* - * now we need to make sure a record only stream has a clock - * so if we're stopping a playback with an active capture - * we need to turn the 0 fill dma on for the xmit side - */ - if (stream_id == SNDRV_PCM_STREAM_PLAYBACK && s1->active) { - /* we need to force fill the xmit DMA with zeros */ - s->tx_spin = 1; - audio_process_dma(s); - } - /* - * we killed a capture only stream, so we should also kill - * the zero fill transmit - */ - else { - if (s1->tx_spin) { - s1->tx_spin = 0; - audio_stop_dma(s1); - } - } - - break; - case SNDRV_PCM_TRIGGER_SUSPEND: - s->active = 0; -#ifdef HH_VERSION - sa1100_dma_stop(s->dmach); -#else - //FIXME - DMA API -#endif - s->old_offset = audio_get_dma_pos(s) + 1; -#ifdef HH_VERSION - sa1100_dma_flush_all(s->dmach); -#else - //FIXME - DMA API -#endif - s->periods = 0; - break; - case SNDRV_PCM_TRIGGER_RESUME: - s->active = 1; - s->tx_spin = 0; - audio_process_dma(s); - if (stream_id == SNDRV_PCM_STREAM_CAPTURE && !s1->active) { - s1->tx_spin = 1; - audio_process_dma(s1); - } - break; - case SNDRV_PCM_TRIGGER_PAUSE_PUSH: -#ifdef HH_VERSION - sa1100_dma_stop(s->dmach); -#else - //FIXME - DMA API -#endif - s->active = 0; - if (stream_id == SNDRV_PCM_STREAM_PLAYBACK) { - if (s1->active) { - s->tx_spin = 1; - s->old_offset = audio_get_dma_pos(s) + 1; -#ifdef HH_VERSION - sa1100_dma_flush_all(s->dmach); -#else - //FIXME - DMA API -#endif - audio_process_dma(s); - } - } else { - if (s1->tx_spin) { - s1->tx_spin = 0; -#ifdef HH_VERSION - sa1100_dma_flush_all(s1->dmach); -#else - //FIXME - DMA API -#endif - } - } - break; - case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: - s->active = 1; - if (s->old_offset) { - s->tx_spin = 0; - audio_process_dma(s); - break; - } - if (stream_id == SNDRV_PCM_STREAM_CAPTURE && !s1->active) { - s1->tx_spin = 1; - audio_process_dma(s1); - } -#ifdef HH_VERSION - sa1100_dma_resume(s->dmach); -#else - //FIXME - DMA API -#endif - break; - default: - err = -EINVAL; - break; - } - spin_unlock(&s->dma_lock); - return err; -} - -static int snd_sa11xx_uda1341_prepare(struct snd_pcm_substream *substream) -{ - struct sa11xx_uda1341 *chip = snd_pcm_substream_chip(substream); - struct snd_pcm_runtime *runtime = substream->runtime; - struct audio_stream *s = &chip->s[substream->pstr->stream]; - - /* set requested samplerate */ - sa11xx_uda1341_set_samplerate(chip, runtime->rate); - - /* set requestd format when available */ - /* set FMT here !!! FIXME */ - - s->period = 0; - s->periods = 0; - - return 0; -} - -static snd_pcm_uframes_t snd_sa11xx_uda1341_pointer(struct snd_pcm_substream *substream) -{ - struct sa11xx_uda1341 *chip = snd_pcm_substream_chip(substream); - return audio_get_dma_pos(&chip->s[substream->pstr->stream]); -} - -/* }}} */ - -static struct snd_pcm_hardware snd_sa11xx_uda1341_capture = -{ - .info = (SNDRV_PCM_INFO_INTERLEAVED | - SNDRV_PCM_INFO_BLOCK_TRANSFER | - SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_MMAP_VALID | - SNDRV_PCM_INFO_PAUSE | SNDRV_PCM_INFO_RESUME), - .formats = SNDRV_PCM_FMTBIT_S16_LE, - .rates = (SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_16000 |\ - SNDRV_PCM_RATE_22050 | SNDRV_PCM_RATE_32000 |\ - SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000 |\ - SNDRV_PCM_RATE_KNOT), - .rate_min = 8000, - .rate_max = 48000, - .channels_min = 2, - .channels_max = 2, - .buffer_bytes_max = 64*1024, - .period_bytes_min = 64, - .period_bytes_max = DMA_BUF_SIZE, - .periods_min = 2, - .periods_max = 255, - .fifo_size = 0, -}; - -static struct snd_pcm_hardware snd_sa11xx_uda1341_playback = -{ - .info = (SNDRV_PCM_INFO_INTERLEAVED | - SNDRV_PCM_INFO_BLOCK_TRANSFER | - SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_MMAP_VALID | - SNDRV_PCM_INFO_PAUSE | SNDRV_PCM_INFO_RESUME), - .formats = SNDRV_PCM_FMTBIT_S16_LE, - .rates = (SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_16000 |\ - SNDRV_PCM_RATE_22050 | SNDRV_PCM_RATE_32000 |\ - SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000 |\ - SNDRV_PCM_RATE_KNOT), - .rate_min = 8000, - .rate_max = 48000, - .channels_min = 2, - .channels_max = 2, - .buffer_bytes_max = 64*1024, - .period_bytes_min = 64, - .period_bytes_max = DMA_BUF_SIZE, - .periods_min = 2, - .periods_max = 255, - .fifo_size = 0, -}; - -static int snd_card_sa11xx_uda1341_open(struct snd_pcm_substream *substream) -{ - struct sa11xx_uda1341 *chip = snd_pcm_substream_chip(substream); - struct snd_pcm_runtime *runtime = substream->runtime; - int stream_id = substream->pstr->stream; - int err; - - chip->s[stream_id].stream = substream; - - if (stream_id == SNDRV_PCM_STREAM_PLAYBACK) - runtime->hw = snd_sa11xx_uda1341_playback; - else - runtime->hw = snd_sa11xx_uda1341_capture; - if ((err = snd_pcm_hw_constraint_integer(runtime, SNDRV_PCM_HW_PARAM_PERIODS)) < 0) - return err; - if ((err = snd_pcm_hw_constraint_list(runtime, 0, SNDRV_PCM_HW_PARAM_RATE, &hw_constraints_rates)) < 0) - return err; - - return 0; -} - -static int snd_card_sa11xx_uda1341_close(struct snd_pcm_substream *substream) -{ - struct sa11xx_uda1341 *chip = snd_pcm_substream_chip(substream); - - chip->s[substream->pstr->stream].stream = NULL; - return 0; -} - -/* {{{ HW params & free */ - -static int snd_sa11xx_uda1341_hw_params(struct snd_pcm_substream *substream, - struct snd_pcm_hw_params *hw_params) -{ - - return snd_pcm_lib_malloc_pages(substream, params_buffer_bytes(hw_params)); -} - -static int snd_sa11xx_uda1341_hw_free(struct snd_pcm_substream *substream) -{ - return snd_pcm_lib_free_pages(substream); -} - -/* }}} */ - -static struct snd_pcm_ops snd_card_sa11xx_uda1341_playback_ops = { - .open = snd_card_sa11xx_uda1341_open, - .close = snd_card_sa11xx_uda1341_close, - .ioctl = snd_pcm_lib_ioctl, - .hw_params = snd_sa11xx_uda1341_hw_params, - .hw_free = snd_sa11xx_uda1341_hw_free, - .prepare = snd_sa11xx_uda1341_prepare, - .trigger = snd_sa11xx_uda1341_trigger, - .pointer = snd_sa11xx_uda1341_pointer, -}; - -static struct snd_pcm_ops snd_card_sa11xx_uda1341_capture_ops = { - .open = snd_card_sa11xx_uda1341_open, - .close = snd_card_sa11xx_uda1341_close, - .ioctl = snd_pcm_lib_ioctl, - .hw_params = snd_sa11xx_uda1341_hw_params, - .hw_free = snd_sa11xx_uda1341_hw_free, - .prepare = snd_sa11xx_uda1341_prepare, - .trigger = snd_sa11xx_uda1341_trigger, - .pointer = snd_sa11xx_uda1341_pointer, -}; - -static int __init snd_card_sa11xx_uda1341_pcm(struct sa11xx_uda1341 *sa11xx_uda1341, int device) -{ - struct snd_pcm *pcm; - int err; - - if ((err = snd_pcm_new(sa11xx_uda1341->card, "UDA1341 PCM", device, 1, 1, &pcm)) < 0) - return err; - - /* - * this sets up our initial buffers and sets the dma_type to isa. - * isa works but I'm not sure why (or if) it's the right choice - * this may be too large, trying it for now - */ - snd_pcm_lib_preallocate_pages_for_all(pcm, SNDRV_DMA_TYPE_DEV, - snd_dma_isa_data(), - 64*1024, 64*1024); - - snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_PLAYBACK, &snd_card_sa11xx_uda1341_playback_ops); - snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_CAPTURE, &snd_card_sa11xx_uda1341_capture_ops); - pcm->private_data = sa11xx_uda1341; - pcm->info_flags = 0; - strcpy(pcm->name, "UDA1341 PCM"); - - sa11xx_uda1341_audio_init(sa11xx_uda1341); - - /* setup DMA controller */ - audio_dma_request(&sa11xx_uda1341->s[SNDRV_PCM_STREAM_PLAYBACK], audio_dma_callback); - audio_dma_request(&sa11xx_uda1341->s[SNDRV_PCM_STREAM_CAPTURE], audio_dma_callback); - - sa11xx_uda1341->pcm = pcm; - - return 0; -} - -/* }}} */ - -/* {{{ module init & exit */ - -#ifdef CONFIG_PM - -static int snd_sa11xx_uda1341_suspend(struct platform_device *devptr, - pm_message_t state) -{ - struct snd_card *card = platform_get_drvdata(devptr); - struct sa11xx_uda1341 *chip = card->private_data; - - snd_power_change_state(card, SNDRV_CTL_POWER_D3hot); - snd_pcm_suspend_all(chip->pcm); -#ifdef HH_VERSION - sa1100_dma_sleep(chip->s[SNDRV_PCM_STREAM_PLAYBACK].dmach); - sa1100_dma_sleep(chip->s[SNDRV_PCM_STREAM_CAPTURE].dmach); -#else - //FIXME -#endif - l3_command(chip->uda1341, CMD_SUSPEND, NULL); - sa11xx_uda1341_audio_shutdown(chip); - - return 0; -} - -static int snd_sa11xx_uda1341_resume(struct platform_device *devptr) -{ - struct snd_card *card = platform_get_drvdata(devptr); - struct sa11xx_uda1341 *chip = card->private_data; - - sa11xx_uda1341_audio_init(chip); - l3_command(chip->uda1341, CMD_RESUME, NULL); -#ifdef HH_VERSION - sa1100_dma_wakeup(chip->s[SNDRV_PCM_STREAM_PLAYBACK].dmach); - sa1100_dma_wakeup(chip->s[SNDRV_PCM_STREAM_CAPTURE].dmach); -#else - //FIXME -#endif - snd_power_change_state(card, SNDRV_CTL_POWER_D0); - return 0; -} -#endif /* COMFIG_PM */ - -void snd_sa11xx_uda1341_free(struct snd_card *card) -{ - struct sa11xx_uda1341 *chip = card->private_data; - - audio_dma_free(&chip->s[SNDRV_PCM_STREAM_PLAYBACK]); - audio_dma_free(&chip->s[SNDRV_PCM_STREAM_CAPTURE]); -} - -static int __devinit sa11xx_uda1341_probe(struct platform_device *devptr) -{ - int err; - struct snd_card *card; - struct sa11xx_uda1341 *chip; - - /* register the soundcard */ - card = snd_card_new(-1, id, THIS_MODULE, sizeof(struct sa11xx_uda1341)); - if (card == NULL) - return -ENOMEM; - - chip = card->private_data; - spin_lock_init(&chip->s[0].dma_lock); - spin_lock_init(&chip->s[1].dma_lock); - - card->private_free = snd_sa11xx_uda1341_free; - chip->card = card; - chip->samplerate = AUDIO_RATE_DEFAULT; - - // mixer - if ((err = snd_chip_uda1341_mixer_new(card, &chip->uda1341))) - goto nodev; - - // PCM - if ((err = snd_card_sa11xx_uda1341_pcm(chip, 0)) < 0) - goto nodev; - - strcpy(card->driver, "UDA1341"); - strcpy(card->shortname, "H3600 UDA1341TS"); - sprintf(card->longname, "Compaq iPAQ H3600 with Philips UDA1341TS"); - - snd_card_set_dev(card, &devptr->dev); - - if ((err = snd_card_register(card)) == 0) { - printk( KERN_INFO "iPAQ audio support initialized\n" ); - platform_set_drvdata(devptr, card); - return 0; - } - - nodev: - snd_card_free(card); - return err; -} - -static int __devexit sa11xx_uda1341_remove(struct platform_device *devptr) -{ - snd_card_free(platform_get_drvdata(devptr)); - platform_set_drvdata(devptr, NULL); - return 0; -} - -#define SA11XX_UDA1341_DRIVER "sa11xx_uda1341" - -static struct platform_driver sa11xx_uda1341_driver = { - .probe = sa11xx_uda1341_probe, - .remove = __devexit_p(sa11xx_uda1341_remove), -#ifdef CONFIG_PM - .suspend = snd_sa11xx_uda1341_suspend, - .resume = snd_sa11xx_uda1341_resume, -#endif - .driver = { - .name = SA11XX_UDA1341_DRIVER, - }, -}; - -static int __init sa11xx_uda1341_init(void) -{ - int err; - - if (!machine_is_h3xxx()) - return -ENODEV; - if ((err = platform_driver_register(&sa11xx_uda1341_driver)) < 0) - return err; - device = platform_device_register_simple(SA11XX_UDA1341_DRIVER, -1, NULL, 0); - if (!IS_ERR(device)) { - if (platform_get_drvdata(device)) - return 0; - platform_device_unregister(device); - err = -ENODEV; - } else - err = PTR_ERR(device); - platform_driver_unregister(&sa11xx_uda1341_driver); - return err; -} - -static void __exit sa11xx_uda1341_exit(void) -{ - platform_device_unregister(device); - platform_driver_unregister(&sa11xx_uda1341_driver); -} - -module_init(sa11xx_uda1341_init); -module_exit(sa11xx_uda1341_exit); - -/* }}} */ - -/* - * Local variables: - * indent-tabs-mode: t - * End: - */ diff --git a/sound/i2c/Makefile b/sound/i2c/Makefile index 3797066..36879bf 100644 --- a/sound/i2c/Makefile +++ b/sound/i2c/Makefile @@ -7,8 +7,6 @@ snd-i2c-objs := i2c.o snd-cs8427-objs := cs8427.o snd-tea6330t-objs := tea6330t.o -obj-$(CONFIG_L3) += l3/ - obj-$(CONFIG_SND) += other/ # Toplevel Module Dependency diff --git a/sound/i2c/l3/Makefile b/sound/i2c/l3/Makefile deleted file mode 100644 index 49455b8..0000000 --- a/sound/i2c/l3/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# Makefile for ALSA -# - -snd-uda1341-objs := uda1341.o - -# Module Dependency -obj-$(CONFIG_SND_SA11XX_UDA1341) += snd-uda1341.o diff --git a/sound/i2c/l3/uda1341.c b/sound/i2c/l3/uda1341.c deleted file mode 100644 index 9840eb4..0000000 --- a/sound/i2c/l3/uda1341.c +++ /dev/null @@ -1,935 +0,0 @@ -/* - * Philips UDA1341 mixer device driver - * Copyright (c) 2002 Tomas Kasparek <tomas.kasparek(a)seznam.cz> - * - * Portions are Copyright (C) 2000 Lernout & Hauspie Speech Products, N.V. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License. - * - * History: - * - * 2002-03-13 Tomas Kasparek initial release - based on uda1341.c from OSS - * 2002-03-28 Tomas Kasparek basic mixer is working (volume, bass, treble) - * 2002-03-30 Tomas Kasparek proc filesystem support, complete mixer and DSP - * features support - * 2002-04-12 Tomas Kasparek proc interface update, code cleanup - * 2002-05-12 Tomas Kasparek another code cleanup - */ - -#include <linux/module.h> -#include <linux/init.h> -#include <linux/types.h> -#include <linux/slab.h> -#include <linux/errno.h> -#include <linux/ioctl.h> - -#include <asm/uaccess.h> - -#include <sound/core.h> -#include <sound/control.h> -#include <sound/initval.h> -#include <sound/info.h> - -#include <linux/l3/l3.h> - -#include <sound/uda1341.h> - -/* {{{ HW regs definition */ - -#define STAT0 0x00 -#define STAT1 0x80 -#define STAT_MASK 0x80 - -#define DATA0_0 0x00 -#define DATA0_1 0x40 -#define DATA0_2 0x80 -#define DATA_MASK 0xc0 - -#define IS_DATA0(x) ((x) >= data0_0 && (x) <= data0_2) -#define IS_DATA1(x) ((x) == data1) -#define IS_STATUS(x) ((x) == stat0 || (x) == stat1) -#define IS_EXTEND(x) ((x) >= ext0 && (x) <= ext6) - -/* }}} */ - - -static const char *peak_names[] = { - "before", - "after", -}; - -static const char *filter_names[] = { - "flat", - "min", - "min", - "max", -}; - -static const char *mixer_names[] = { - "double differential", - "input channel 1 (line in)", - "input channel 2 (microphone)", - "digital mixer", -}; - -static const char *deemp_names[] = { - "none", - "32 kHz", - "44.1 kHz", - "48 kHz", -}; - -enum uda1341_regs_names { - stat0, - stat1, - data0_0, - data0_1, - data0_2, - data1, - ext0, - ext1, - ext2, - empty, - ext4, - ext5, - ext6, - uda1341_reg_last, -}; - -static const char *uda1341_reg_names[] = { - "stat 0 ", - "stat 1 ", - "data 00", - "data 01", - "data 02", - "data 1 ", - "ext 0", - "ext 1", - "ext 2", - "empty", - "ext 4", - "ext 5", - "ext 6", -}; - -static const int uda1341_enum_items[] = { - 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, - 2, //peak - before/after - 4, //deemp - none/32/44.1/48 - 0, - 4, //filter - flat/min/min/max - 0, 0, 0, - 4, //mixer - differ/line/mic/mixer - 0, 0, 0, 0, 0, -}; - -static const char ** uda1341_enum_names[] = { - NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, - peak_names, //peak - before/after - deemp_names, //deemp - none/32/44.1/48 - NULL, - filter_names, //filter - flat/min/min/max - NULL, NULL, NULL, - mixer_names, //mixer - differ/line/mic/mixer - NULL, NULL, NULL, NULL, NULL, -}; - -typedef int uda1341_cfg[CMD_LAST]; - -struct uda1341 { - int (*write) (struct l3_client *uda1341, unsigned short reg, unsigned short val); - int (*read) (struct l3_client *uda1341, unsigned short reg); - unsigned char regs[uda1341_reg_last]; - int active; - spinlock_t reg_lock; - struct snd_card *card; - uda1341_cfg cfg; -#ifdef CONFIG_PM - unsigned char suspend_regs[uda1341_reg_last]; - uda1341_cfg suspend_cfg; -#endif -}; - -/* transfer 8bit integer into string with binary representation */ -static void int2str_bin8(uint8_t val, char *buf) -{ - const int size = sizeof(val) * 8; - int i; - - for (i= 0; i < size; i++){ - *(buf++) = (val >> (size - 1)) ? '1' : '0'; - val <<= 1; - } - *buf = '\0'; //end the string with zero -} - -/* {{{ HW manipulation routines */ - -static int snd_uda1341_codec_write(struct l3_client *clnt, unsigned short reg, unsigned short val) -{ - struct uda1341 *uda = clnt->driver_data; - unsigned char buf[2] = { 0xc0, 0xe0 }; // for EXT addressing - int err = 0; - - uda->regs[reg] = val; - - if (uda->active) { - if (IS_DATA0(reg)) { - err = l3_write(clnt, UDA1341_DATA0, (const unsigned char *)&val, 1); - } else if (IS_DATA1(reg)) { - err = l3_write(clnt, UDA1341_DATA1, (const unsigned char *)&val, 1); - } else if (IS_STATUS(reg)) { - err = l3_write(clnt, UDA1341_STATUS, (const unsigned char *)&val, 1); - } else if (IS_EXTEND(reg)) { - buf[0] |= (reg - ext0) & 0x7; //EXT address - buf[1] |= val; //EXT data - err = l3_write(clnt, UDA1341_DATA0, (const unsigned char *)buf, 2); - } - } else - printk(KERN_ERR "UDA1341 codec not active!\n"); - return err; -} - -static int snd_uda1341_codec_read(struct l3_client *clnt, unsigned short reg) -{ - unsigned char val; - int err; - - err = l3_read(clnt, reg, &val, 1); - if (err == 1) - // use just 6bits - the rest is address of the reg - return val & 63; - return err < 0 ? err : -EIO; -} - -static inline int snd_uda1341_valid_reg(struct l3_client *clnt, unsigned short reg) -{ - return reg < uda1341_reg_last; -} - -static int snd_uda1341_update_bits(struct l3_client *clnt, unsigned short reg, - unsigned short mask, unsigned short shift, - unsigned short value, int flush) -{ - int change; - unsigned short old, new; - struct uda1341 *uda = clnt->driver_data; - -#if 0 - printk(KERN_DEBUG "update_bits: reg: %s mask: %d shift: %d val: %d\n", - uda1341_reg_names[reg], mask, shift, value); -#endif - - if (!snd_uda1341_valid_reg(clnt, reg)) - return -EINVAL; - spin_lock(&uda->reg_lock); - old = uda->regs[reg]; - new = (old & ~(mask << shift)) | (value << shift); - change = old != new; - if (change) { - if (flush) uda->write(clnt, reg, new); - uda->regs[reg] = new; - } - spin_unlock(&uda->reg_lock); - return change; -} - -static int snd_uda1341_cfg_write(struct l3_client *clnt, unsigned short what, - unsigned short value, int flush) -{ - struct uda1341 *uda = clnt->driver_data; - int ret = 0; -#ifdef CONFIG_PM - int reg; -#endif - -#if 0 - printk(KERN_DEBUG "cfg_write what: %d value: %d\n", what, value); -#endif - - uda->cfg[what] = value; - - switch(what) { - case CMD_RESET: - ret = snd_uda1341_update_bits(clnt, data0_2, 1, 2, 1, flush); // MUTE - ret = snd_uda1341_update_bits(clnt, stat0, 1, 6, 1, flush); // RESET - ret = snd_uda1341_update_bits(clnt, stat0, 1, 6, 0, flush); // RESTORE - uda->cfg[CMD_RESET]=0; - break; - case CMD_FS: - ret = snd_uda1341_update_bits(clnt, stat0, 3, 4, value, flush); - break; - case CMD_FORMAT: - ret = snd_uda1341_update_bits(clnt, stat0, 7, 1, value, flush); - break; - case CMD_OGAIN: - ret = snd_uda1341_update_bits(clnt, stat1, 1, 6, value, flush); - break; - case CMD_IGAIN: - ret = snd_uda1341_update_bits(clnt, stat1, 1, 5, value, flush); - break; - case CMD_DAC: - ret = snd_uda1341_update_bits(clnt, stat1, 1, 0, value, flush); - break; - case CMD_ADC: - ret = snd_uda1341_update_bits(clnt, stat1, 1, 1, value, flush); - break; - case CMD_VOLUME: - ret = snd_uda1341_update_bits(clnt, data0_0, 63, 0, value, flush); - break; - case CMD_BASS: - ret = snd_uda1341_update_bits(clnt, data0_1, 15, 2, value, flush); - break; - case CMD_TREBBLE: - ret = snd_uda1341_update_bits(clnt, data0_1, 3, 0, value, flush); - break; - case CMD_PEAK: - ret = snd_uda1341_update_bits(clnt, data0_2, 1, 5, value, flush); - break; - case CMD_DEEMP: - ret = snd_uda1341_update_bits(clnt, data0_2, 3, 3, value, flush); - break; - case CMD_MUTE: - ret = snd_uda1341_update_bits(clnt, data0_2, 1, 2, value, flush); - break; - case CMD_FILTER: - ret = snd_uda1341_update_bits(clnt, data0_2, 3, 0, value, flush); - break; - case CMD_CH1: - ret = snd_uda1341_update_bits(clnt, ext0, 31, 0, value, flush); - break; - case CMD_CH2: - ret = snd_uda1341_update_bits(clnt, ext1, 31, 0, value, flush); - break; - case CMD_MIC: - ret = snd_uda1341_update_bits(clnt, ext2, 7, 2, value, flush); - break; - case CMD_MIXER: - ret = snd_uda1341_update_bits(clnt, ext2, 3, 0, value, flush); - break; - case CMD_AGC: - ret = snd_uda1341_update_bits(clnt, ext4, 1, 4, value, flush); - break; - case CMD_IG: - ret = snd_uda1341_update_bits(clnt, ext4, 3, 0, value & 0x3, flush); - ret = snd_uda1341_update_bits(clnt, ext5, 31, 0, value >> 2, flush); - break; - case CMD_AGC_TIME: - ret = snd_uda1341_update_bits(clnt, ext6, 7, 2, value, flush); - break; - case CMD_AGC_LEVEL: - ret = snd_uda1341_update_bits(clnt, ext6, 3, 0, value, flush); - break; -#ifdef CONFIG_PM - case CMD_SUSPEND: - for (reg = stat0; reg < uda1341_reg_last; reg++) - uda->suspend_regs[reg] = uda->regs[reg]; - for (reg = 0; reg < CMD_LAST; reg++) - uda->suspend_cfg[reg] = uda->cfg[reg]; - break; - case CMD_RESUME: - for (reg = stat0; reg < uda1341_reg_last; reg++) - snd_uda1341_codec_write(clnt, reg, uda->suspend_regs[reg]); - for (reg = 0; reg < CMD_LAST; reg++) - uda->cfg[reg] = uda->suspend_cfg[reg]; - break; -#endif - default: - ret = -EINVAL; - break; - } - - if (!uda->active) - printk(KERN_ERR "UDA1341 codec not active!\n"); - return ret; -} - -/* }}} */ - -/* {{{ Proc interface */ -#ifdef CONFIG_PROC_FS - -static const char *format_names[] = { - "I2S-bus", - "LSB 16bits", - "LSB 18bits", - "LSB 20bits", - "MSB", - "in LSB 16bits/out MSB", - "in LSB 18bits/out MSB", - "in LSB 20bits/out MSB", -}; - -static const char *fs_names[] = { - "512*fs", - "384*fs", - "256*fs", - "Unused - bad value!", -}; - -static const char* bass_values[][16] = { - {"0 dB", "0 dB", "0 dB", "0 dB", "0 dB", "0 dB", "0 dB", "0 dB", "0 dB", "0 dB", "0 dB", - "0 dB", "0 dB", "0 dB", "0 dB", "undefined", }, //flat - {"0 dB", "2 dB", "4 dB", "6 dB", "8 dB", "10 dB", "12 dB", "14 dB", "16 dB", "18 dB", "18 dB", - "18 dB", "18 dB", "18 dB", "18 dB", "undefined",}, // min - {"0 dB", "2 dB", "4 dB", "6 dB", "8 dB", "10 dB", "12 dB", "14 dB", "16 dB", "18 dB", "18 dB", - "18 dB", "18 dB", "18 dB", "18 dB", "undefined",}, // min - {"0 dB", "2 dB", "4 dB", "6 dB", "8 dB", "10 dB", "12 dB", "14 dB", "16 dB", "18 dB", "20 dB", - "22 dB", "24 dB", "24 dB", "24 dB", "undefined",}, // max -}; - -static const char *mic_sens_value[] = { - "-3 dB", "0 dB", "3 dB", "9 dB", "15 dB", "21 dB", "27 dB", "not used", -}; - -static const unsigned short AGC_atime[] = { - 11, 16, 11, 16, 21, 11, 16, 21, -}; - -static const unsigned short AGC_dtime[] = { - 100, 100, 200, 200, 200, 400, 400, 400, -}; - -static const char *AGC_level[] = { - "-9.0", "-11.5", "-15.0", "-17.5", -}; - -static const char *ig_small_value[] = { - "-3.0", "-2.5", "-2.0", "-1.5", "-1.0", "-0.5", -}; - -/* - * this was computed as peak_value[i] = pow((63-i)*1.42,1.013) - * - * UDA1341 datasheet on page 21: Peak value (dB) = (Peak level - 63.5)*5*log2 - * There is an table with these values [level]=value: [3]=-90.31, [7]=-84.29 - * [61]=-2.78, [62] = -1.48, [63] = 0.0 - * I tried to compute it, but using but even using logarithm with base either 10 or 2 - * i was'n able to get values in the table from the formula. So I constructed another - * formula (see above) to interpolate the values as good as possible. If there is some - * mistake, please contact me on tomas.kasparek(a)seznam.cz. Thanks. - * UDA1341TS datasheet is available at: - * http://www-us9.semiconductors.com/acrobat/datasheets/UDA1341TS_3.pdf - */ -static const char *peak_value[] = { - "-INF dB", "N.A.", "N.A", "90.31 dB", "N.A.", "N.A.", "N.A.", "-84.29 dB", - "-82.65 dB", "-81.13 dB", "-79.61 dB", "-78.09 dB", "-76.57 dB", "-75.05 dB", "-73.53 dB", - "-72.01 dB", "-70.49 dB", "-68.97 dB", "-67.45 dB", "-65.93 dB", "-64.41 dB", "-62.90 dB", - "-61.38 dB", "-59.86 dB", "-58.35 dB", "-56.83 dB", "-55.32 dB", "-53.80 dB", "-52.29 dB", - "-50.78 dB", "-49.26 dB", "-47.75 dB", "-46.24 dB", "-44.73 dB", "-43.22 dB", "-41.71 dB", - "-40.20 dB", "-38.69 dB", "-37.19 dB", "-35.68 dB", "-34.17 dB", "-32.67 dB", "-31.17 dB", - "-29.66 dB", "-28.16 dB", "-26.66 dB", "-25.16 dB", "-23.66 dB", "-22.16 dB", "-20.67 dB", - "-19.17 dB", "-17.68 dB", "-16.19 dB", "-14.70 dB", "-13.21 dB", "-11.72 dB", "-10.24 dB", - "-8.76 dB", "-7.28 dB", "-5.81 dB", "-4.34 dB", "-2.88 dB", "-1.43 dB", "0.00 dB", -}; - -static void snd_uda1341_proc_read(struct snd_info_entry *entry, - struct snd_info_buffer *buffer) -{ - struct l3_client *clnt = entry->private_data; - struct uda1341 *uda = clnt->driver_data; - int peak; - - peak = snd_uda1341_codec_read(clnt, UDA1341_DATA1); - if (peak < 0) - peak = 0; - - snd_iprintf(buffer, "%s\n\n", uda->card->longname); - - // for information about computed values see UDA1341TS datasheet pages 15 - 21 - snd_iprintf(buffer, "DAC power : %s\n", uda->cfg[CMD_DAC] ? "on" : "off"); - snd_iprintf(buffer, "ADC power : %s\n", uda->cfg[CMD_ADC] ? "on" : "off"); - snd_iprintf(buffer, "Clock frequency : %s\n", fs_names[uda->cfg[CMD_FS]]); - snd_iprintf(buffer, "Data format : %s\n\n", format_names[uda->cfg[CMD_FORMAT]]); - - snd_iprintf(buffer, "Filter mode : %s\n", filter_names[uda->cfg[CMD_FILTER]]); - snd_iprintf(buffer, "Mixer mode : %s\n", mixer_names[uda->cfg[CMD_MIXER]]); - snd_iprintf(buffer, "De-emphasis : %s\n", deemp_names[uda->cfg[CMD_DEEMP]]); - snd_iprintf(buffer, "Peak detection pos. : %s\n", uda->cfg[CMD_PEAK] ? "after" : "before"); - snd_iprintf(buffer, "Peak value : %s\n\n", peak_value[peak]); - - snd_iprintf(buffer, "Automatic Gain Ctrl : %s\n", uda->cfg[CMD_AGC] ? "on" : "off"); - snd_iprintf(buffer, "AGC attack time : %d ms\n", AGC_atime[uda->cfg[CMD_AGC_TIME]]); - snd_iprintf(buffer, "AGC decay time : %d ms\n", AGC_dtime[uda->cfg[CMD_AGC_TIME]]); - snd_iprintf(buffer, "AGC output level : %s dB\n\n", AGC_level[uda->cfg[CMD_AGC_LEVEL]]); - - snd_iprintf(buffer, "Mute : %s\n", uda->cfg[CMD_MUTE] ? "on" : "off"); - - if (uda->cfg[CMD_VOLUME] == 0) - snd_iprintf(buffer, "Volume : 0 dB\n"); - else if (uda->cfg[CMD_VOLUME] < 62) - snd_iprintf(buffer, "Volume : %d dB\n", -1*uda->cfg[CMD_VOLUME] +1); - else - snd_iprintf(buffer, "Volume : -INF dB\n"); - snd_iprintf(buffer, "Bass : %s\n", bass_values[uda->cfg[CMD_FILTER]][uda->cfg[CMD_BASS]]); - snd_iprintf(buffer, "Trebble : %d dB\n", uda->cfg[CMD_FILTER] ? 2*uda->cfg[CMD_TREBBLE] : 0); - snd_iprintf(buffer, "Input Gain (6dB) : %s\n", uda->cfg[CMD_IGAIN] ? "on" : "off"); - snd_iprintf(buffer, "Output Gain (6dB) : %s\n", uda->cfg[CMD_OGAIN] ? "on" : "off"); - snd_iprintf(buffer, "Mic sensitivity : %s\n", mic_sens_value[uda->cfg[CMD_MIC]]); - - - if(uda->cfg[CMD_CH1] < 31) - snd_iprintf(buffer, "Mixer gain channel 1: -%d.%c dB\n", - ((uda->cfg[CMD_CH1] >> 1) * 3) + (uda->cfg[CMD_CH1] & 1), - uda->cfg[CMD_CH1] & 1 ? '5' : '0'); - else - snd_iprintf(buffer, "Mixer gain channel 1: -INF dB\n"); - if(uda->cfg[CMD_CH2] < 31) - snd_iprintf(buffer, "Mixer gain channel 2: -%d.%c dB\n", - ((uda->cfg[CMD_CH2] >> 1) * 3) + (uda->cfg[CMD_CH2] & 1), - uda->cfg[CMD_CH2] & 1 ? '5' : '0'); - else - snd_iprintf(buffer, "Mixer gain channel 2: -INF dB\n"); - - if(uda->cfg[CMD_IG] > 5) - snd_iprintf(buffer, "Input Amp. Gain ch 2: %d.%c dB\n", - (uda->cfg[CMD_IG] >> 1) -3, uda->cfg[CMD_IG] & 1 ? '5' : '0'); - else - snd_iprintf(buffer, "Input Amp. Gain ch 2: %s dB\n", ig_small_value[uda->cfg[CMD_IG]]); -} - -static void snd_uda1341_proc_regs_read(struct snd_info_entry *entry, - struct snd_info_buffer *buffer) -{ - struct l3_client *clnt = entry->private_data; - struct uda1341 *uda = clnt->driver_data; - int reg; - char buf[12]; - - for (reg = 0; reg < uda1341_reg_last; reg ++) { - if (reg == empty) - continue; - int2str_bin8(uda->regs[reg], buf); - snd_iprintf(buffer, "%s = %s\n", uda1341_reg_names[reg], buf); - } - - int2str_bin8(snd_uda1341_codec_read(clnt, UDA1341_DATA1), buf); - snd_iprintf(buffer, "DATA1 = %s\n", buf); -} -#endif /* CONFIG_PROC_FS */ - -static void __devinit snd_uda1341_proc_init(struct snd_card *card, struct l3_client *clnt) -{ - struct snd_info_entry *entry; - - if (! snd_card_proc_new(card, "uda1341", &entry)) - snd_info_set_text_ops(entry, clnt, snd_uda1341_proc_read); - if (! snd_card_proc_new(card, "uda1341-regs", &entry)) - snd_info_set_text_ops(entry, clnt, snd_uda1341_proc_regs_read); -} - -/* }}} */ - -/* {{{ Mixer controls setting */ - -/* {{{ UDA1341 single functions */ - -#define UDA1341_SINGLE(xname, where, reg, shift, mask, invert) \ -{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = xname, .info = snd_uda1341_info_single, \ - .get = snd_uda1341_get_single, .put = snd_uda1341_put_single, \ - .private_value = where | (reg << 5) | (shift << 9) | (mask << 12) | (invert << 18) \ -} - -static int snd_uda1341_info_single(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_info *uinfo) -{ - int mask = (kcontrol->private_value >> 12) & 63; - - uinfo->type = mask == 1 ? SNDRV_CTL_ELEM_TYPE_BOOLEAN : SNDRV_CTL_ELEM_TYPE_INTEGER; - uinfo->count = 1; - uinfo->value.integer.min = 0; - uinfo->value.integer.max = mask; - return 0; -} - -static int snd_uda1341_get_single(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_value *ucontrol) -{ - struct l3_client *clnt = snd_kcontrol_chip(kcontrol); - struct uda1341 *uda = clnt->driver_data; - int where = kcontrol->private_value & 31; - int mask = (kcontrol->private_value >> 12) & 63; - int invert = (kcontrol->private_value >> 18) & 1; - - ucontrol->value.integer.value[0] = uda->cfg[where]; - if (invert) - ucontrol->value.integer.value[0] = mask - ucontrol->value.integer.value[0]; - - return 0; -} - -static int snd_uda1341_put_single(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_value *ucontrol) -{ - struct l3_client *clnt = snd_kcontrol_chip(kcontrol); - struct uda1341 *uda = clnt->driver_data; - int where = kcontrol->private_value & 31; - int reg = (kcontrol->private_value >> 5) & 15; - int shift = (kcontrol->private_value >> 9) & 7; - int mask = (kcontrol->private_value >> 12) & 63; - int invert = (kcontrol->private_value >> 18) & 1; - unsigned short val; - - val = (ucontrol->value.integer.value[0] & mask); - if (invert) - val = mask - val; - - uda->cfg[where] = val; - return snd_uda1341_update_bits(clnt, reg, mask, shift, val, FLUSH); -} - -/* }}} */ - -/* {{{ UDA1341 enum functions */ - -#define UDA1341_ENUM(xname, where, reg, shift, mask, invert) \ -{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = xname, .info = snd_uda1341_info_enum, \ - .get = snd_uda1341_get_enum, .put = snd_uda1341_put_enum, \ - .private_value = where | (reg << 5) | (shift << 9) | (mask << 12) | (invert << 18) \ -} - -static int snd_uda1341_info_enum(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_info *uinfo) -{ - int where = kcontrol->private_value & 31; - const char **texts; - - // this register we don't handle this way - if (!uda1341_enum_items[where]) - return -EINVAL; - - uinfo->type = SNDRV_CTL_ELEM_TYPE_ENUMERATED; - uinfo->count = 1; - uinfo->value.enumerated.items = uda1341_enum_items[where]; - - if (uinfo->value.enumerated.item >= uda1341_enum_items[where]) - uinfo->value.enumerated.item = uda1341_enum_items[where] - 1; - - texts = uda1341_enum_names[where]; - strcpy(uinfo->value.enumerated.name, texts[uinfo->value.enumerated.item]); - return 0; -} - -static int snd_uda1341_get_enum(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_value *ucontrol) -{ - struct l3_client *clnt = snd_kcontrol_chip(kcontrol); - struct uda1341 *uda = clnt->driver_data; - int where = kcontrol->private_value & 31; - - ucontrol->value.enumerated.item[0] = uda->cfg[where]; - return 0; -} - -static int snd_uda1341_put_enum(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_value *ucontrol) -{ - struct l3_client *clnt = snd_kcontrol_chip(kcontrol); - struct uda1341 *uda = clnt->driver_data; - int where = kcontrol->private_value & 31; - int reg = (kcontrol->private_value >> 5) & 15; - int shift = (kcontrol->private_value >> 9) & 7; - int mask = (kcontrol->private_value >> 12) & 63; - - uda->cfg[where] = (ucontrol->value.enumerated.item[0] & mask); - - return snd_uda1341_update_bits(clnt, reg, mask, shift, uda->cfg[where], FLUSH); -} - -/* }}} */ - -/* {{{ UDA1341 2regs functions */ - -#define UDA1341_2REGS(xname, where, reg_1, reg_2, shift_1, shift_2, mask_1, mask_2, invert) \ -{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname), .info = snd_uda1341_info_2regs, \ - .get = snd_uda1341_get_2regs, .put = snd_uda1341_put_2regs, \ - .private_value = where | (reg_1 << 5) | (reg_2 << 9) | (shift_1 << 13) | (shift_2 << 16) | \ - (mask_1 << 19) | (mask_2 << 25) | (invert << 31) \ -} - - -static int snd_uda1341_info_2regs(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_info *uinfo) -{ - int mask_1 = (kcontrol->private_value >> 19) & 63; - int mask_2 = (kcontrol->private_value >> 25) & 63; - int mask; - - mask = (mask_2 + 1) * (mask_1 + 1) - 1; - uinfo->type = mask == 1 ? SNDRV_CTL_ELEM_TYPE_BOOLEAN : SNDRV_CTL_ELEM_TYPE_INTEGER; - uinfo->count = 1; - uinfo->value.integer.min = 0; - uinfo->value.integer.max = mask; - return 0; -} - -static int snd_uda1341_get_2regs(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_value *ucontrol) -{ - struct l3_client *clnt = snd_kcontrol_chip(kcontrol); - struct uda1341 *uda = clnt->driver_data; - int where = kcontrol->private_value & 31; - int mask_1 = (kcontrol->private_value >> 19) & 63; - int mask_2 = (kcontrol->private_value >> 25) & 63; - int invert = (kcontrol->private_value >> 31) & 1; - int mask; - - mask = (mask_2 + 1) * (mask_1 + 1) - 1; - - ucontrol->value.integer.value[0] = uda->cfg[where]; - if (invert) - ucontrol->value.integer.value[0] = mask - ucontrol->value.integer.value[0]; - return 0; -} - -static int snd_uda1341_put_2regs(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_value *ucontrol) -{ - struct l3_client *clnt = snd_kcontrol_chip(kcontrol); - struct uda1341 *uda = clnt->driver_data; - int where = kcontrol->private_value & 31; - int reg_1 = (kcontrol->private_value >> 5) & 15; - int reg_2 = (kcontrol->private_value >> 9) & 15; - int shift_1 = (kcontrol->private_value >> 13) & 7; - int shift_2 = (kcontrol->private_value >> 16) & 7; - int mask_1 = (kcontrol->private_value >> 19) & 63; - int mask_2 = (kcontrol->private_value >> 25) & 63; - int invert = (kcontrol->private_value >> 31) & 1; - int mask; - unsigned short val1, val2, val; - - val = ucontrol->value.integer.value[0]; - - mask = (mask_2 + 1) * (mask_1 + 1) - 1; - - val1 = val & mask_1; - val2 = (val / (mask_1 + 1)) & mask_2; - - if (invert) { - val1 = mask_1 - val1; - val2 = mask_2 - val2; - } - - uda->cfg[where] = invert ? mask - val : val; - - //FIXME - return value - snd_uda1341_update_bits(clnt, reg_1, mask_1, shift_1, val1, FLUSH); - return snd_uda1341_update_bits(clnt, reg_2, mask_2, shift_2, val2, FLUSH); -} - -/* }}} */ - -static struct snd_kcontrol_new snd_uda1341_controls[] = { - UDA1341_SINGLE("Master Playback Switch", CMD_MUTE, data0_2, 2, 1, 1), - UDA1341_SINGLE("Master Playback Volume", CMD_VOLUME, data0_0, 0, 63, 1), - - UDA1341_SINGLE("Bass Playback Volume", CMD_BASS, data0_1, 2, 15, 0), - UDA1341_SINGLE("Treble Playback Volume", CMD_TREBBLE, data0_1, 0, 3, 0), - - UDA1341_SINGLE("Input Gain Switch", CMD_IGAIN, stat1, 5, 1, 0), - UDA1341_SINGLE("Output Gain Switch", CMD_OGAIN, stat1, 6, 1, 0), - - UDA1341_SINGLE("Mixer Gain Channel 1 Volume", CMD_CH1, ext0, 0, 31, 1), - UDA1341_SINGLE("Mixer Gain Channel 2 Volume", CMD_CH2, ext1, 0, 31, 1), - - UDA1341_SINGLE("Mic Sensitivity Volume", CMD_MIC, ext2, 2, 7, 0), - - UDA1341_SINGLE("AGC Output Level", CMD_AGC_LEVEL, ext6, 0, 3, 0), - UDA1341_SINGLE("AGC Time Constant", CMD_AGC_TIME, ext6, 2, 7, 0), - UDA1341_SINGLE("AGC Time Constant Switch", CMD_AGC, ext4, 4, 1, 0), - - UDA1341_SINGLE("DAC Power", CMD_DAC, stat1, 0, 1, 0), - UDA1341_SINGLE("ADC Power", CMD_ADC, stat1, 1, 1, 0), - - UDA1341_ENUM("Peak detection", CMD_PEAK, data0_2, 5, 1, 0), - UDA1341_ENUM("De-emphasis", CMD_DEEMP, data0_2, 3, 3, 0), - UDA1341_ENUM("Mixer mode", CMD_MIXER, ext2, 0, 3, 0), - UDA1341_ENUM("Filter mode", CMD_FILTER, data0_2, 0, 3, 0), - - UDA1341_2REGS("Gain Input Amplifier Gain (channel 2)", CMD_IG, ext4, ext5, 0, 0, 3, 31, 0), -}; - -static void uda1341_free(struct l3_client *clnt) -{ - l3_detach_client(clnt); // calls kfree for driver_data (struct uda1341) - kfree(clnt); -} - -static int uda1341_dev_free(struct snd_device *device) -{ - struct l3_client *clnt = device->device_data; - uda1341_free(clnt); - return 0; -} - -int __init snd_chip_uda1341_mixer_new(struct snd_card *card, struct l3_client **clntp) -{ - static struct snd_device_ops ops = { - .dev_free = uda1341_dev_free, - }; - struct l3_client *clnt; - int idx, err; - - if (snd_BUG_ON(!card)) - return -EINVAL; - - clnt = kzalloc(sizeof(*clnt), GFP_KERNEL); - if (clnt == NULL) - return -ENOMEM; - - if ((err = l3_attach_client(clnt, "l3-bit-sa1100-gpio", UDA1341_ALSA_NAME))) { - kfree(clnt); - return err; - } - - for (idx = 0; idx < ARRAY_SIZE(snd_uda1341_controls); idx++) { - if ((err = snd_ctl_add(card, snd_ctl_new1(&snd_uda1341_controls[idx], clnt))) < 0) { - uda1341_free(clnt); - return err; - } - } - - if ((err = snd_device_new(card, SNDRV_DEV_CODEC, clnt, &ops)) < 0) { - uda1341_free(clnt); - return err; - } - - *clntp = clnt; - strcpy(card->mixername, "UDA1341TS Mixer"); - ((struct uda1341 *)clnt->driver_data)->card = card; - - snd_uda1341_proc_init(card, clnt); - - return 0; -} - -/* }}} */ - -/* {{{ L3 operations */ - -static int uda1341_attach(struct l3_client *clnt) -{ - struct uda1341 *uda; - - uda = kzalloc(sizeof(*uda), 0, GFP_KERNEL); - if (!uda) - return -ENOMEM; - - /* init fixed parts of my copy of registers */ - uda->regs[stat0] = STAT0; - uda->regs[stat1] = STAT1; - - uda->regs[data0_0] = DATA0_0; - uda->regs[data0_1] = DATA0_1; - uda->regs[data0_2] = DATA0_2; - - uda->write = snd_uda1341_codec_write; - uda->read = snd_uda1341_codec_read; - - spin_lock_init(&uda->reg_lock); - - clnt->driver_data = uda; - return 0; -} - -static void uda1341_detach(struct l3_client *clnt) -{ - kfree(clnt->driver_data); -} - -static int -uda1341_command(struct l3_client *clnt, int cmd, void *arg) -{ - if (cmd != CMD_READ_REG) - return snd_uda1341_cfg_write(clnt, cmd, (int) arg, FLUSH); - - return snd_uda1341_codec_read(clnt, (int) arg); -} - -static int uda1341_open(struct l3_client *clnt) -{ - struct uda1341 *uda = clnt->driver_data; - - uda->active = 1; - - /* init default configuration */ - snd_uda1341_cfg_write(clnt, CMD_RESET, 0, REGS_ONLY); - snd_uda1341_cfg_write(clnt, CMD_FS, F256, FLUSH); // unknown state after reset - snd_uda1341_cfg_write(clnt, CMD_FORMAT, LSB16, FLUSH); // unknown state after reset - snd_uda1341_cfg_write(clnt, CMD_OGAIN, ON, FLUSH); // default off after reset - snd_uda1341_cfg_write(clnt, CMD_IGAIN, ON, FLUSH); // default off after reset - snd_uda1341_cfg_write(clnt, CMD_DAC, ON, FLUSH); // ??? default value after reset - snd_uda1341_cfg_write(clnt, CMD_ADC, ON, FLUSH); // ??? default value after reset - snd_uda1341_cfg_write(clnt, CMD_VOLUME, 20, FLUSH); // default 0dB after reset - snd_uda1341_cfg_write(clnt, CMD_BASS, 0, REGS_ONLY); // default value after reset - snd_uda1341_cfg_write(clnt, CMD_TREBBLE, 0, REGS_ONLY); // default value after reset - snd_uda1341_cfg_write(clnt, CMD_PEAK, AFTER, REGS_ONLY);// default value after reset - snd_uda1341_cfg_write(clnt, CMD_DEEMP, NONE, REGS_ONLY);// default value after reset - //at this moment should be QMUTED by h3600_audio_init - snd_uda1341_cfg_write(clnt, CMD_MUTE, OFF, REGS_ONLY); // default value after reset - snd_uda1341_cfg_write(clnt, CMD_FILTER, MAX, FLUSH); // defaul flat after reset - snd_uda1341_cfg_write(clnt, CMD_CH1, 31, FLUSH); // default value after reset - snd_uda1341_cfg_write(clnt, CMD_CH2, 4, FLUSH); // default value after reset - snd_uda1341_cfg_write(clnt, CMD_MIC, 4, FLUSH); // default 0dB after reset - snd_uda1341_cfg_write(clnt, CMD_MIXER, MIXER, FLUSH); // default doub.dif.mode - snd_uda1341_cfg_write(clnt, CMD_AGC, OFF, FLUSH); // default value after reset - snd_uda1341_cfg_write(clnt, CMD_IG, 0, FLUSH); // unknown state after reset - snd_uda1341_cfg_write(clnt, CMD_AGC_TIME, 0, FLUSH); // default value after reset - snd_uda1341_cfg_write(clnt, CMD_AGC_LEVEL, 0, FLUSH); // default value after reset - - return 0; -} - -static void uda1341_close(struct l3_client *clnt) -{ - struct uda1341 *uda = clnt->driver_data; - - uda->active = 0; -} - -/* }}} */ - -/* {{{ Module and L3 initialization */ - -static struct l3_ops uda1341_ops = { - .open = uda1341_open, - .command = uda1341_command, - .close = uda1341_close, -}; - -static struct l3_driver uda1341_driver = { - .name = UDA1341_ALSA_NAME, - .attach_client = uda1341_attach, - .detach_client = uda1341_detach, - .ops = &uda1341_ops, - .owner = THIS_MODULE, -}; - -static int __init uda1341_init(void) -{ - return l3_add_driver(&uda1341_driver); -} - -static void __exit uda1341_exit(void) -{ - l3_del_driver(&uda1341_driver); -} - -module_init(uda1341_init); -module_exit(uda1341_exit); - -MODULE_AUTHOR("Tomas Kasparek <tomas.kasparek(a)seznam.cz>"); -MODULE_LICENSE("GPL"); -MODULE_DESCRIPTION("Philips UDA1341 CODEC driver for ALSA"); -MODULE_SUPPORTED_DEVICE("{{UDA1341,UDA1341TS}}"); - -EXPORT_SYMBOL(snd_chip_uda1341_mixer_new); - -/* }}} */ - -/* - * Local variables: - * indent-tabs-mode: t - * End: - */ -- 1.6.1.3

3 5

[alsa-devel] Intel HDA volume low
by Daniel Stodden 13 Mar '09

13 Mar '09

Hi. I've got a Lenovo Thinkpad T400 with snd_hda_intel: 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) Subsystem: Lenovo Device 20f2 I think this is the same chip which recently quirks entries to work around docking issues on the Thinkpad x200. The codec is identified as a conexant CX20561 (Hermosa). Running Ubuntu 8.10 with 2.6.27, the Volume is extremely low. Quality seems okay, but setting Master and PCM outputs to 100% is barely audible. There's a bunch of similar reports on the Internet. I could not find any workaround but Window users usually report the volume should be fine. I tried 2.6.28 but to no avail. Will verify against latest git. Could someone help me fix this? I don't actually know much about the hardware in question, but would also willing to poke a little around in patch_conexant.c, if that could help identifying the issue. Provided someone someone around here has advice on what to try out. Cheers, Daniell

2 1

[alsa-devel] [PATCH 1/3][RFC] ASoC: pxa-ssp: Use 16-bit DMA for magician stereo
by Philipp Zabel 13 Mar '09

13 Mar '09

Please advise how this behaviour could be made configurable. I guess the only machines that will ever need this are HTC Magician, Blueangel and Himalaya. Signed-off-by: Philipp Zabel <philipp.zabel(a)gmail.com> --- sound/soc/pxa/pxa-ssp.c | 11 +++++++++-- 1 files changed, 9 insertions(+), 2 deletions(-) diff --git a/sound/soc/pxa/pxa-ssp.c b/sound/soc/pxa/pxa-ssp.c index 569c0a6..bc9d306 100644 --- a/sound/soc/pxa/pxa-ssp.c +++ b/sound/soc/pxa/pxa-ssp.c @@ -22,6 +22,7 @@ #include <linux/io.h> #include <asm/irq.h> +#include <asm/mach-types.h> #include <sound/core.h> #include <sound/pcm.h> @@ -634,8 +635,14 @@ static int pxa_ssp_hw_params(struct snd_pcm_substream *substream, /* select correct DMA params */ if (substream->stream != SNDRV_PCM_STREAM_PLAYBACK) dma = 1; /* capture DMA offset is 1,3 */ - if (chn == 2) - dma += 2; /* stereo DMA offset is 2, mono is 0 */ + /* FIXME: Magician needs a way to configure 16-bit DMA for stereo */ + if (machine_is_magician()) { + if (width == 32) + dma += 2; /* 32-bit DMA offset is 2, 16-bit is 0 */ + } else { + if (chn == 2) + dma += 2; /* stereo DMA offset is 2, mono is 0 */ + } cpu_dai->dma_data = ssp_dma_params[cpu_dai->id][dma]; dev_dbg(&ssp->pdev->dev, "pxa_ssp_hw_params: dma %d\n", dma); -- 1.6.2

6 24

[PATCH] ALSA: drop outdated and broken sa11xx-uda1341 driver
by Dmitry Artamonow 12 Mar '09

12 Mar '09

It depends on L3 support from 2.4 kernel (CONFIG_L3) that never got merged into mainline. Since there's no way to use it on any of supported machines (iPaq h3100 or h3600), better drop it for now. It can be reimplemented later using ASoC infrastructure (there's already a driver for uda1341 codec in mainline, so only CPU and machine parts need to be written). Signed-off-by: Dmitry Artamonow <mad_soft(a)inbox.ru> Cc: Russell King <linux(a)arm.linux.org.uk> --- include/sound/uda1341.h | 126 ------ sound/arm/Kconfig | 11 - sound/arm/Makefile | 3 - sound/arm/sa11xx-uda1341.c | 984 -------------------------------------------- sound/i2c/Makefile | 2 - sound/i2c/l3/Makefile | 8 - sound/i2c/l3/uda1341.c | 935 ----------------------------------------- 7 files changed, 0 insertions(+), 2069 deletions(-) delete mode 100644 include/sound/uda1341.h delete mode 100644 sound/arm/sa11xx-uda1341.c delete mode 100644 sound/i2c/l3/Makefile delete mode 100644 sound/i2c/l3/uda1341.c diff --git a/include/sound/uda1341.h b/include/sound/uda1341.h deleted file mode 100644 index 110d5dc..0000000 --- a/include/sound/uda1341.h +++ /dev/null @@ -1,126 +0,0 @@ -/* - * linux/include/linux/l3/uda1341.h - * - * Philips UDA1341 mixer device driver for ALSA - * - * Copyright (c) 2002 Tomas Kasparek <tomas.kasparek(a)seznam.cz> - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License. - * - * History: - * - * 2002-03-13 Tomas Kasparek Initial release - based on uda1341.h from OSS - * 2002-03-30 Tomas Kasparek Proc filesystem support, complete mixer and DSP - * features support - */ - -#define UDA1341_ALSA_NAME "snd-uda1341" - -/* - * Default rate set after inicialization - */ -#define AUDIO_RATE_DEFAULT 44100 - -/* - * UDA1341 L3 address and command types - */ -#define UDA1341_L3ADDR 5 -#define UDA1341_DATA0 (UDA1341_L3ADDR << 2 | 0) -#define UDA1341_DATA1 (UDA1341_L3ADDR << 2 | 1) -#define UDA1341_STATUS (UDA1341_L3ADDR << 2 | 2) - -enum uda1341_onoff { - OFF=0, - ON, -}; - -enum uda1341_format { - I2S=0, - LSB16, - LSB18, - LSB20, - MSB, - LSB16MSB, - LSB18MSB, - LSB20MSB, -}; - -enum uda1341_fs { - F512=0, - F384, - F256, - Funused, -}; - -enum uda1341_peak { - BEFORE=0, - AFTER, -}; - -enum uda1341_filter { - FLAT=0, - MIN, - MIN2, - MAX, -}; - -enum uda1341_mixer { - DOUBLE, - LINE, - MIC, - MIXER, -}; - -enum uda1341_deemp { - NONE, - D32, - D44, - D48, -}; - -enum uda1341_config { - CMD_READ_REG = 0, - CMD_RESET, - CMD_FS, - CMD_FORMAT, - CMD_OGAIN, - CMD_IGAIN, - CMD_DAC, - CMD_ADC, - CMD_VOLUME, - CMD_BASS, - CMD_TREBBLE, - CMD_PEAK, - CMD_DEEMP, - CMD_MUTE, - CMD_FILTER, - CMD_CH1, - CMD_CH2, - CMD_MIC, - CMD_MIXER, - CMD_AGC, - CMD_IG, - CMD_AGC_TIME, - CMD_AGC_LEVEL, -#ifdef CONFIG_PM - CMD_SUSPEND, - CMD_RESUME, -#endif - CMD_LAST, -}; - -enum write_through { - //used in update_bits (write_cfg) to avoid l3_write - just update local copy of regs. - REGS_ONLY=0, - //update local regs and write value to uda1341 - do l3_write - FLUSH, -}; - -int __init snd_chip_uda1341_mixer_new(struct snd_card *card, struct l3_client **clnt); - -/* - * Local variables: - * indent-tabs-mode: t - * End: - */ diff --git a/sound/arm/Kconfig b/sound/arm/Kconfig index f8e6de4..885683a 100644 --- a/sound/arm/Kconfig +++ b/sound/arm/Kconfig @@ -11,17 +11,6 @@ menuconfig SND_ARM if SND_ARM -config SND_SA11XX_UDA1341 - tristate "SA11xx UDA1341TS driver (iPaq H3600)" - depends on ARCH_SA1100 && L3 - select SND_PCM - help - Say Y here if you have a Compaq iPaq H3x00 handheld computer - and want to use its Philips UDA 1341 audio chip. - - To compile this driver as a module, choose M here: the module - will be called snd-sa11xx-uda1341. - config SND_ARMAACI tristate "ARM PrimeCell PL041 AC Link support" depends on ARM_AMBA diff --git a/sound/arm/Makefile b/sound/arm/Makefile index 2054de1..5a549ed 100644 --- a/sound/arm/Makefile +++ b/sound/arm/Makefile @@ -2,9 +2,6 @@ # Makefile for ALSA # -obj-$(CONFIG_SND_SA11XX_UDA1341) += snd-sa11xx-uda1341.o -snd-sa11xx-uda1341-objs := sa11xx-uda1341.o - obj-$(CONFIG_SND_ARMAACI) += snd-aaci.o snd-aaci-objs := aaci.o devdma.o diff --git a/sound/arm/sa11xx-uda1341.c b/sound/arm/sa11xx-uda1341.c deleted file mode 100644 index 7101d3d..0000000 --- a/sound/arm/sa11xx-uda1341.c +++ /dev/null @@ -1,984 +0,0 @@ -/* - * Driver for Philips UDA1341TS on Compaq iPAQ H3600 soundcard - * Copyright (C) 2002 Tomas Kasparek <tomas.kasparek(a)seznam.cz> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License. - * - * History: - * - * 2002-03-13 Tomas Kasparek initial release - based on h3600-uda1341.c from OSS - * 2002-03-20 Tomas Kasparek playback over ALSA is working - * 2002-03-28 Tomas Kasparek playback over OSS emulation is working - * 2002-03-29 Tomas Kasparek basic capture is working (native ALSA) - * 2002-03-29 Tomas Kasparek capture is working (OSS emulation) - * 2002-04-04 Tomas Kasparek better rates handling (allow non-standard rates) - * 2003-02-14 Brian Avery fixed full duplex mode, other updates - * 2003-02-20 Tomas Kasparek merged updates by Brian (except HAL) - * 2003-04-19 Jaroslav Kysela recoded DMA stuff to follow 2.4.18rmk3-hh24 kernel - * working suspend and resume - * 2003-04-28 Tomas Kasparek updated work by Jaroslav to compile it under 2.5.x again - * merged HAL layer (patches from Brian) - */ - -/*************************************************************************************************** -* -* To understand what Alsa Drivers should be doing look at "Writing an Alsa Driver" by Takashi Iwai -* available in the Alsa doc section on the website -* -* A few notes to make things clearer. The UDA1341 is hooked up to Serial port 4 on the SA1100. -* We are using SSP mode to talk to the UDA1341. The UDA1341 bit & wordselect clocks are generated -* by this UART. Unfortunately, the clock only runs if the transmit buffer has something in it. -* So, if we are just recording, we feed the transmit DMA stream a bunch of 0x0000 so that the -* transmit buffer is full and the clock keeps going. The zeroes come from FLUSH_BASE_PHYS which -* is a mem loc that always decodes to 0's w/ no off chip access. -* -* Some alsa terminology: -* frame => num_channels * sample_size e.g stereo 16 bit is 2 * 16 = 32 bytes -* period => the least number of bytes that will generate an interrupt e.g. we have a 1024 byte -* buffer and 4 periods in the runtime structure this means we'll get an int every 256 -* bytes or 4 times per buffer. -* A number of the sizes are in frames rather than bytes, use frames_to_bytes and -* bytes_to_frames to convert. The easiest way to tell the units is to look at the -* type i.e. runtime-> buffer_size is in frames and its type is snd_pcm_uframes_t -* -* Notes about the pointer fxn: -* The pointer fxn needs to return the offset into the dma buffer in frames. -* Interrupts must be blocked before calling the dma_get_pos fxn to avoid race with interrupts. -* -* Notes about pause/resume -* Implementing this would be complicated so it's skipped. The problem case is: -* A full duplex connection is going, then play is paused. At this point you need to start xmitting -* 0's to keep the record active which means you cant just freeze the dma and resume it later you'd -* need to save off the dma info, and restore it properly on a resume. Yeach! -* -* Notes about transfer methods: -* The async write calls fail. I probably need to implement something else to support them? -* -***************************************************************************************************/ - -#include <linux/module.h> -#include <linux/moduleparam.h> -#include <linux/init.h> -#include <linux/err.h> -#include <linux/platform_device.h> -#include <linux/errno.h> -#include <linux/ioctl.h> -#include <linux/delay.h> -#include <linux/slab.h> - -#ifdef CONFIG_PM -#include <linux/pm.h> -#endif - -#include <mach/hardware.h> -#include <mach/h3600.h> -#include <asm/mach-types.h> -#include <asm/dma.h> - -#include <sound/core.h> -#include <sound/pcm.h> -#include <sound/initval.h> - -#include <linux/l3/l3.h> - -#undef DEBUG_MODE -#undef DEBUG_FUNCTION_NAMES -#include <sound/uda1341.h> - -/* - * FIXME: Is this enough as autodetection of 2.4.X-rmkY-hhZ kernels? - * We use DMA stuff from 2.4.18-rmk3-hh24 here to be able to compile this - * module for Familiar 0.6.1 - */ - -/* {{{ Type definitions */ - -MODULE_AUTHOR("Tomas Kasparek <tomas.kasparek(a)seznam.cz>"); -MODULE_LICENSE("GPL"); -MODULE_DESCRIPTION("SA1100/SA1111 + UDA1341TS driver for ALSA"); -MODULE_SUPPORTED_DEVICE("{{UDA1341,iPAQ H3600 UDA1341TS}}"); - -static char *id; /* ID for this card */ - -module_param(id, charp, 0444); -MODULE_PARM_DESC(id, "ID string for SA1100/SA1111 + UDA1341TS soundcard."); - -struct audio_stream { - char *id; /* identification string */ - int stream_id; /* numeric identification */ - dma_device_t dma_dev; /* device identifier for DMA */ -#ifdef HH_VERSION - dmach_t dmach; /* dma channel identification */ -#else - dma_regs_t *dma_regs; /* points to our DMA registers */ -#endif - unsigned int active:1; /* we are using this stream for transfer now */ - int period; /* current transfer period */ - int periods; /* current count of periods registerd in the DMA engine */ - int tx_spin; /* are we recoding - flag used to do DMA trans. for sync */ - unsigned int old_offset; - spinlock_t dma_lock; /* for locking in DMA operations (see dma-sa1100.c in the kernel) */ - struct snd_pcm_substream *stream; -}; - -struct sa11xx_uda1341 { - struct snd_card *card; - struct l3_client *uda1341; - struct snd_pcm *pcm; - long samplerate; - struct audio_stream s[2]; /* playback & capture */ -}; - -static unsigned int rates[] = { - 8000, 10666, 10985, 14647, - 16000, 21970, 22050, 24000, - 29400, 32000, 44100, 48000, -}; - -static struct snd_pcm_hw_constraint_list hw_constraints_rates = { - .count = ARRAY_SIZE(rates), - .list = rates, - .mask = 0, -}; - -static struct platform_device *device; - -/* }}} */ - -/* {{{ Clock and sample rate stuff */ - -/* - * Stop-gap solution until rest of hh.org HAL stuff is merged. - */ -#define GPIO_H3600_CLK_SET0 GPIO_GPIO (12) -#define GPIO_H3600_CLK_SET1 GPIO_GPIO (13) - -#ifdef CONFIG_SA1100_H3XXX -#define clr_sa11xx_uda1341_egpio(x) clr_h3600_egpio(x) -#define set_sa11xx_uda1341_egpio(x) set_h3600_egpio(x) -#else -#error This driver could serve H3x00 handhelds only! -#endif - -static void sa11xx_uda1341_set_audio_clock(long val) -{ - switch (val) { - case 24000: case 32000: case 48000: /* 00: 12.288 MHz */ - GPCR = GPIO_H3600_CLK_SET0 | GPIO_H3600_CLK_SET1; - break; - - case 22050: case 29400: case 44100: /* 01: 11.2896 MHz */ - GPSR = GPIO_H3600_CLK_SET0; - GPCR = GPIO_H3600_CLK_SET1; - break; - - case 8000: case 10666: case 16000: /* 10: 4.096 MHz */ - GPCR = GPIO_H3600_CLK_SET0; - GPSR = GPIO_H3600_CLK_SET1; - break; - - case 10985: case 14647: case 21970: /* 11: 5.6245 MHz */ - GPSR = GPIO_H3600_CLK_SET0 | GPIO_H3600_CLK_SET1; - break; - } -} - -static void sa11xx_uda1341_set_samplerate(struct sa11xx_uda1341 *sa11xx_uda1341, long rate) -{ - int clk_div = 0; - int clk=0; - - /* We don't want to mess with clocks when frames are in flight */ - Ser4SSCR0 &= ~SSCR0_SSE; - /* wait for any frame to complete */ - udelay(125); - - /* - * We have the following clock sources: - * 4.096 MHz, 5.6245 MHz, 11.2896 MHz, 12.288 MHz - * Those can be divided either by 256, 384 or 512. - * This makes up 12 combinations for the following samplerates... - */ - if (rate >= 48000) - rate = 48000; - else if (rate >= 44100) - rate = 44100; - else if (rate >= 32000) - rate = 32000; - else if (rate >= 29400) - rate = 29400; - else if (rate >= 24000) - rate = 24000; - else if (rate >= 22050) - rate = 22050; - else if (rate >= 21970) - rate = 21970; - else if (rate >= 16000) - rate = 16000; - else if (rate >= 14647) - rate = 14647; - else if (rate >= 10985) - rate = 10985; - else if (rate >= 10666) - rate = 10666; - else - rate = 8000; - - /* Set the external clock generator */ - - sa11xx_uda1341_set_audio_clock(rate); - - /* Select the clock divisor */ - switch (rate) { - case 8000: - case 10985: - case 22050: - case 24000: - clk = F512; - clk_div = SSCR0_SerClkDiv(16); - break; - case 16000: - case 21970: - case 44100: - case 48000: - clk = F256; - clk_div = SSCR0_SerClkDiv(8); - break; - case 10666: - case 14647: - case 29400: - case 32000: - clk = F384; - clk_div = SSCR0_SerClkDiv(12); - break; - } - - /* FMT setting should be moved away when other FMTs are added (FIXME) */ - l3_command(sa11xx_uda1341->uda1341, CMD_FORMAT, (void *)LSB16); - - l3_command(sa11xx_uda1341->uda1341, CMD_FS, (void *)clk); - Ser4SSCR0 = (Ser4SSCR0 & ~0xff00) + clk_div + SSCR0_SSE; - sa11xx_uda1341->samplerate = rate; -} - -/* }}} */ - -/* {{{ HW init and shutdown */ - -static void sa11xx_uda1341_audio_init(struct sa11xx_uda1341 *sa11xx_uda1341) -{ - unsigned long flags; - - /* Setup DMA stuff */ - sa11xx_uda1341->s[SNDRV_PCM_STREAM_PLAYBACK].id = "UDA1341 out"; - sa11xx_uda1341->s[SNDRV_PCM_STREAM_PLAYBACK].stream_id = SNDRV_PCM_STREAM_PLAYBACK; - sa11xx_uda1341->s[SNDRV_PCM_STREAM_PLAYBACK].dma_dev = DMA_Ser4SSPWr; - - sa11xx_uda1341->s[SNDRV_PCM_STREAM_CAPTURE].id = "UDA1341 in"; - sa11xx_uda1341->s[SNDRV_PCM_STREAM_CAPTURE].stream_id = SNDRV_PCM_STREAM_CAPTURE; - sa11xx_uda1341->s[SNDRV_PCM_STREAM_CAPTURE].dma_dev = DMA_Ser4SSPRd; - - /* Initialize the UDA1341 internal state */ - - /* Setup the uarts */ - local_irq_save(flags); - GAFR |= (GPIO_SSP_CLK); - GPDR &= ~(GPIO_SSP_CLK); - Ser4SSCR0 = 0; - Ser4SSCR0 = SSCR0_DataSize(16) + SSCR0_TI + SSCR0_SerClkDiv(8); - Ser4SSCR1 = SSCR1_SClkIactL + SSCR1_SClk1P + SSCR1_ExtClk; - Ser4SSCR0 |= SSCR0_SSE; - local_irq_restore(flags); - - /* Enable the audio power */ - - clr_sa11xx_uda1341_egpio(IPAQ_EGPIO_CODEC_NRESET); - set_sa11xx_uda1341_egpio(IPAQ_EGPIO_AUDIO_ON); - set_sa11xx_uda1341_egpio(IPAQ_EGPIO_QMUTE); - - /* Wait for the UDA1341 to wake up */ - mdelay(1); //FIXME - was removed by Perex - Why? - - /* Initialize the UDA1341 internal state */ - l3_open(sa11xx_uda1341->uda1341); - - /* external clock configuration (after l3_open - regs must be initialized */ - sa11xx_uda1341_set_samplerate(sa11xx_uda1341, sa11xx_uda1341->samplerate); - - /* Wait for the UDA1341 to wake up */ - set_sa11xx_uda1341_egpio(IPAQ_EGPIO_CODEC_NRESET); - mdelay(1); - - /* make the left and right channels unswapped (flip the WS latch) */ - Ser4SSDR = 0; - - clr_sa11xx_uda1341_egpio(IPAQ_EGPIO_QMUTE); -} - -static void sa11xx_uda1341_audio_shutdown(struct sa11xx_uda1341 *sa11xx_uda1341) -{ - /* mute on */ - set_sa11xx_uda1341_egpio(IPAQ_EGPIO_QMUTE); - - /* disable the audio power and all signals leading to the audio chip */ - l3_close(sa11xx_uda1341->uda1341); - Ser4SSCR0 = 0; - clr_sa11xx_uda1341_egpio(IPAQ_EGPIO_CODEC_NRESET); - - /* power off and mute off */ - /* FIXME - is muting off necesary??? */ - - clr_sa11xx_uda1341_egpio(IPAQ_EGPIO_AUDIO_ON); - clr_sa11xx_uda1341_egpio(IPAQ_EGPIO_QMUTE); -} - -/* }}} */ - -/* {{{ DMA staff */ - -/* - * these are the address and sizes used to fill the xmit buffer - * so we can get a clock in record only mode - */ -#define FORCE_CLOCK_ADDR (dma_addr_t)FLUSH_BASE_PHYS -#define FORCE_CLOCK_SIZE 4096 // was 2048 - -// FIXME Why this value exactly - wrote comment -#define DMA_BUF_SIZE 8176 /* <= MAX_DMA_SIZE from asm/arch-sa1100/dma.h */ - -#ifdef HH_VERSION - -static int audio_dma_request(struct audio_stream *s, void (*callback)(void *, int)) -{ - int ret; - - ret = sa1100_request_dma(&s->dmach, s->id, s->dma_dev); - if (ret < 0) { - printk(KERN_ERR "unable to grab audio dma 0x%x\n", s->dma_dev); - return ret; - } - sa1100_dma_set_callback(s->dmach, callback); - return 0; -} - -static inline void audio_dma_free(struct audio_stream *s) -{ - sa1100_free_dma(s->dmach); - s->dmach = -1; -} - -#else - -static int audio_dma_request(struct audio_stream *s, void (*callback)(void *)) -{ - int ret; - - ret = sa1100_request_dma(s->dma_dev, s->id, callback, s, &s->dma_regs); - if (ret < 0) - printk(KERN_ERR "unable to grab audio dma 0x%x\n", s->dma_dev); - return ret; -} - -static void audio_dma_free(struct audio_stream *s) -{ - sa1100_free_dma(s->dma_regs); - s->dma_regs = 0; -} - -#endif - -static u_int audio_get_dma_pos(struct audio_stream *s) -{ - struct snd_pcm_substream *substream = s->stream; - struct snd_pcm_runtime *runtime = substream->runtime; - unsigned int offset; - unsigned long flags; - dma_addr_t addr; - - // this must be called w/ interrupts locked out see dma-sa1100.c in the kernel - spin_lock_irqsave(&s->dma_lock, flags); -#ifdef HH_VERSION - sa1100_dma_get_current(s->dmach, NULL, &addr); -#else - addr = sa1100_get_dma_pos((s)->dma_regs); -#endif - offset = addr - runtime->dma_addr; - spin_unlock_irqrestore(&s->dma_lock, flags); - - offset = bytes_to_frames(runtime,offset); - if (offset >= runtime->buffer_size) - offset = 0; - - return offset; -} - -/* - * this stops the dma and clears the dma ptrs - */ -static void audio_stop_dma(struct audio_stream *s) -{ - unsigned long flags; - - spin_lock_irqsave(&s->dma_lock, flags); - s->active = 0; - s->period = 0; - /* this stops the dma channel and clears the buffer ptrs */ -#ifdef HH_VERSION - sa1100_dma_flush_all(s->dmach); -#else - sa1100_clear_dma(s->dma_regs); -#endif - spin_unlock_irqrestore(&s->dma_lock, flags); -} - -static void audio_process_dma(struct audio_stream *s) -{ - struct snd_pcm_substream *substream = s->stream; - struct snd_pcm_runtime *runtime; - unsigned int dma_size; - unsigned int offset; - int ret; - - /* we are requested to process synchronization DMA transfer */ - if (s->tx_spin) { - if (snd_BUG_ON(s->stream_id != SNDRV_PCM_STREAM_PLAYBACK)) - return; - /* fill the xmit dma buffers and return */ -#ifdef HH_VERSION - sa1100_dma_set_spin(s->dmach, FORCE_CLOCK_ADDR, FORCE_CLOCK_SIZE); -#else - while (1) { - ret = sa1100_start_dma(s->dma_regs, FORCE_CLOCK_ADDR, FORCE_CLOCK_SIZE); - if (ret) - return; - } -#endif - return; - } - - /* must be set here - only valid for running streams, not for forced_clock dma fills */ - runtime = substream->runtime; - while (s->active && s->periods < runtime->periods) { - dma_size = frames_to_bytes(runtime, runtime->period_size); - if (s->old_offset) { - /* a little trick, we need resume from old position */ - offset = frames_to_bytes(runtime, s->old_offset - 1); - s->old_offset = 0; - s->periods = 0; - s->period = offset / dma_size; - offset %= dma_size; - dma_size = dma_size - offset; - if (!dma_size) - continue; /* special case */ - } else { - offset = dma_size * s->period; - snd_BUG_ON(dma_size > DMA_BUF_SIZE); - } -#ifdef HH_VERSION - ret = sa1100_dma_queue_buffer(s->dmach, s, runtime->dma_addr + offset, dma_size); - if (ret) - return; //FIXME -#else - ret = sa1100_start_dma((s)->dma_regs, runtime->dma_addr + offset, dma_size); - if (ret) { - printk(KERN_ERR "audio_process_dma: cannot queue DMA buffer (%i)\n", ret); - return; - } -#endif - - s->period++; - s->period %= runtime->periods; - s->periods++; - } -} - -#ifdef HH_VERSION -static void audio_dma_callback(void *data, int size) -#else -static void audio_dma_callback(void *data) -#endif -{ - struct audio_stream *s = data; - - /* - * If we are getting a callback for an active stream then we inform - * the PCM middle layer we've finished a period - */ - if (s->active) - snd_pcm_period_elapsed(s->stream); - - spin_lock(&s->dma_lock); - if (!s->tx_spin && s->periods > 0) - s->periods--; - audio_process_dma(s); - spin_unlock(&s->dma_lock); -} - -/* }}} */ - -/* {{{ PCM setting */ - -/* {{{ trigger & timer */ - -static int snd_sa11xx_uda1341_trigger(struct snd_pcm_substream *substream, int cmd) -{ - struct sa11xx_uda1341 *chip = snd_pcm_substream_chip(substream); - int stream_id = substream->pstr->stream; - struct audio_stream *s = &chip->s[stream_id]; - struct audio_stream *s1 = &chip->s[stream_id ^ 1]; - int err = 0; - - /* note local interrupts are already disabled in the midlevel code */ - spin_lock(&s->dma_lock); - switch (cmd) { - case SNDRV_PCM_TRIGGER_START: - /* now we need to make sure a record only stream has a clock */ - if (stream_id == SNDRV_PCM_STREAM_CAPTURE && !s1->active) { - /* we need to force fill the xmit DMA with zeros */ - s1->tx_spin = 1; - audio_process_dma(s1); - } - /* this case is when you were recording then you turn on a - * playback stream so we stop (also clears it) the dma first, - * clear the sync flag and then we let it turned on - */ - else { - s->tx_spin = 0; - } - - /* requested stream startup */ - s->active = 1; - audio_process_dma(s); - break; - case SNDRV_PCM_TRIGGER_STOP: - /* requested stream shutdown */ - audio_stop_dma(s); - - /* - * now we need to make sure a record only stream has a clock - * so if we're stopping a playback with an active capture - * we need to turn the 0 fill dma on for the xmit side - */ - if (stream_id == SNDRV_PCM_STREAM_PLAYBACK && s1->active) { - /* we need to force fill the xmit DMA with zeros */ - s->tx_spin = 1; - audio_process_dma(s); - } - /* - * we killed a capture only stream, so we should also kill - * the zero fill transmit - */ - else { - if (s1->tx_spin) { - s1->tx_spin = 0; - audio_stop_dma(s1); - } - } - - break; - case SNDRV_PCM_TRIGGER_SUSPEND: - s->active = 0; -#ifdef HH_VERSION - sa1100_dma_stop(s->dmach); -#else - //FIXME - DMA API -#endif - s->old_offset = audio_get_dma_pos(s) + 1; -#ifdef HH_VERSION - sa1100_dma_flush_all(s->dmach); -#else - //FIXME - DMA API -#endif - s->periods = 0; - break; - case SNDRV_PCM_TRIGGER_RESUME: - s->active = 1; - s->tx_spin = 0; - audio_process_dma(s); - if (stream_id == SNDRV_PCM_STREAM_CAPTURE && !s1->active) { - s1->tx_spin = 1; - audio_process_dma(s1); - } - break; - case SNDRV_PCM_TRIGGER_PAUSE_PUSH: -#ifdef HH_VERSION - sa1100_dma_stop(s->dmach); -#else - //FIXME - DMA API -#endif - s->active = 0; - if (stream_id == SNDRV_PCM_STREAM_PLAYBACK) { - if (s1->active) { - s->tx_spin = 1; - s->old_offset = audio_get_dma_pos(s) + 1; -#ifdef HH_VERSION - sa1100_dma_flush_all(s->dmach); -#else - //FIXME - DMA API -#endif - audio_process_dma(s); - } - } else { - if (s1->tx_spin) { - s1->tx_spin = 0; -#ifdef HH_VERSION - sa1100_dma_flush_all(s1->dmach); -#else - //FIXME - DMA API -#endif - } - } - break; - case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: - s->active = 1; - if (s->old_offset) { - s->tx_spin = 0; - audio_process_dma(s); - break; - } - if (stream_id == SNDRV_PCM_STREAM_CAPTURE && !s1->active) { - s1->tx_spin = 1; - audio_process_dma(s1); - } -#ifdef HH_VERSION - sa1100_dma_resume(s->dmach); -#else - //FIXME - DMA API -#endif - break; - default: - err = -EINVAL; - break; - } - spin_unlock(&s->dma_lock); - return err; -} - -static int snd_sa11xx_uda1341_prepare(struct snd_pcm_substream *substream) -{ - struct sa11xx_uda1341 *chip = snd_pcm_substream_chip(substream); - struct snd_pcm_runtime *runtime = substream->runtime; - struct audio_stream *s = &chip->s[substream->pstr->stream]; - - /* set requested samplerate */ - sa11xx_uda1341_set_samplerate(chip, runtime->rate); - - /* set requestd format when available */ - /* set FMT here !!! FIXME */ - - s->period = 0; - s->periods = 0; - - return 0; -} - -static snd_pcm_uframes_t snd_sa11xx_uda1341_pointer(struct snd_pcm_substream *substream) -{ - struct sa11xx_uda1341 *chip = snd_pcm_substream_chip(substream); - return audio_get_dma_pos(&chip->s[substream->pstr->stream]); -} - -/* }}} */ - -static struct snd_pcm_hardware snd_sa11xx_uda1341_capture = -{ - .info = (SNDRV_PCM_INFO_INTERLEAVED | - SNDRV_PCM_INFO_BLOCK_TRANSFER | - SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_MMAP_VALID | - SNDRV_PCM_INFO_PAUSE | SNDRV_PCM_INFO_RESUME), - .formats = SNDRV_PCM_FMTBIT_S16_LE, - .rates = (SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_16000 |\ - SNDRV_PCM_RATE_22050 | SNDRV_PCM_RATE_32000 |\ - SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000 |\ - SNDRV_PCM_RATE_KNOT), - .rate_min = 8000, - .rate_max = 48000, - .channels_min = 2, - .channels_max = 2, - .buffer_bytes_max = 64*1024, - .period_bytes_min = 64, - .period_bytes_max = DMA_BUF_SIZE, - .periods_min = 2, - .periods_max = 255, - .fifo_size = 0, -}; - -static struct snd_pcm_hardware snd_sa11xx_uda1341_playback = -{ - .info = (SNDRV_PCM_INFO_INTERLEAVED | - SNDRV_PCM_INFO_BLOCK_TRANSFER | - SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_MMAP_VALID | - SNDRV_PCM_INFO_PAUSE | SNDRV_PCM_INFO_RESUME), - .formats = SNDRV_PCM_FMTBIT_S16_LE, - .rates = (SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_16000 |\ - SNDRV_PCM_RATE_22050 | SNDRV_PCM_RATE_32000 |\ - SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000 |\ - SNDRV_PCM_RATE_KNOT), - .rate_min = 8000, - .rate_max = 48000, - .channels_min = 2, - .channels_max = 2, - .buffer_bytes_max = 64*1024, - .period_bytes_min = 64, - .period_bytes_max = DMA_BUF_SIZE, - .periods_min = 2, - .periods_max = 255, - .fifo_size = 0, -}; - -static int snd_card_sa11xx_uda1341_open(struct snd_pcm_substream *substream) -{ - struct sa11xx_uda1341 *chip = snd_pcm_substream_chip(substream); - struct snd_pcm_runtime *runtime = substream->runtime; - int stream_id = substream->pstr->stream; - int err; - - chip->s[stream_id].stream = substream; - - if (stream_id == SNDRV_PCM_STREAM_PLAYBACK) - runtime->hw = snd_sa11xx_uda1341_playback; - else - runtime->hw = snd_sa11xx_uda1341_capture; - if ((err = snd_pcm_hw_constraint_integer(runtime, SNDRV_PCM_HW_PARAM_PERIODS)) < 0) - return err; - if ((err = snd_pcm_hw_constraint_list(runtime, 0, SNDRV_PCM_HW_PARAM_RATE, &hw_constraints_rates)) < 0) - return err; - - return 0; -} - -static int snd_card_sa11xx_uda1341_close(struct snd_pcm_substream *substream) -{ - struct sa11xx_uda1341 *chip = snd_pcm_substream_chip(substream); - - chip->s[substream->pstr->stream].stream = NULL; - return 0; -} - -/* {{{ HW params & free */ - -static int snd_sa11xx_uda1341_hw_params(struct snd_pcm_substream *substream, - struct snd_pcm_hw_params *hw_params) -{ - - return snd_pcm_lib_malloc_pages(substream, params_buffer_bytes(hw_params)); -} - -static int snd_sa11xx_uda1341_hw_free(struct snd_pcm_substream *substream) -{ - return snd_pcm_lib_free_pages(substream); -} - -/* }}} */ - -static struct snd_pcm_ops snd_card_sa11xx_uda1341_playback_ops = { - .open = snd_card_sa11xx_uda1341_open, - .close = snd_card_sa11xx_uda1341_close, - .ioctl = snd_pcm_lib_ioctl, - .hw_params = snd_sa11xx_uda1341_hw_params, - .hw_free = snd_sa11xx_uda1341_hw_free, - .prepare = snd_sa11xx_uda1341_prepare, - .trigger = snd_sa11xx_uda1341_trigger, - .pointer = snd_sa11xx_uda1341_pointer, -}; - -static struct snd_pcm_ops snd_card_sa11xx_uda1341_capture_ops = { - .open = snd_card_sa11xx_uda1341_open, - .close = snd_card_sa11xx_uda1341_close, - .ioctl = snd_pcm_lib_ioctl, - .hw_params = snd_sa11xx_uda1341_hw_params, - .hw_free = snd_sa11xx_uda1341_hw_free, - .prepare = snd_sa11xx_uda1341_prepare, - .trigger = snd_sa11xx_uda1341_trigger, - .pointer = snd_sa11xx_uda1341_pointer, -}; - -static int __init snd_card_sa11xx_uda1341_pcm(struct sa11xx_uda1341 *sa11xx_uda1341, int device) -{ - struct snd_pcm *pcm; - int err; - - if ((err = snd_pcm_new(sa11xx_uda1341->card, "UDA1341 PCM", device, 1, 1, &pcm)) < 0) - return err; - - /* - * this sets up our initial buffers and sets the dma_type to isa. - * isa works but I'm not sure why (or if) it's the right choice - * this may be too large, trying it for now - */ - snd_pcm_lib_preallocate_pages_for_all(pcm, SNDRV_DMA_TYPE_DEV, - snd_dma_isa_data(), - 64*1024, 64*1024); - - snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_PLAYBACK, &snd_card_sa11xx_uda1341_playback_ops); - snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_CAPTURE, &snd_card_sa11xx_uda1341_capture_ops); - pcm->private_data = sa11xx_uda1341; - pcm->info_flags = 0; - strcpy(pcm->name, "UDA1341 PCM"); - - sa11xx_uda1341_audio_init(sa11xx_uda1341); - - /* setup DMA controller */ - audio_dma_request(&sa11xx_uda1341->s[SNDRV_PCM_STREAM_PLAYBACK], audio_dma_callback); - audio_dma_request(&sa11xx_uda1341->s[SNDRV_PCM_STREAM_CAPTURE], audio_dma_callback); - - sa11xx_uda1341->pcm = pcm; - - return 0; -} - -/* }}} */ - -/* {{{ module init & exit */ - -#ifdef CONFIG_PM - -static int snd_sa11xx_uda1341_suspend(struct platform_device *devptr, - pm_message_t state) -{ - struct snd_card *card = platform_get_drvdata(devptr); - struct sa11xx_uda1341 *chip = card->private_data; - - snd_power_change_state(card, SNDRV_CTL_POWER_D3hot); - snd_pcm_suspend_all(chip->pcm); -#ifdef HH_VERSION - sa1100_dma_sleep(chip->s[SNDRV_PCM_STREAM_PLAYBACK].dmach); - sa1100_dma_sleep(chip->s[SNDRV_PCM_STREAM_CAPTURE].dmach); -#else - //FIXME -#endif - l3_command(chip->uda1341, CMD_SUSPEND, NULL); - sa11xx_uda1341_audio_shutdown(chip); - - return 0; -} - -static int snd_sa11xx_uda1341_resume(struct platform_device *devptr) -{ - struct snd_card *card = platform_get_drvdata(devptr); - struct sa11xx_uda1341 *chip = card->private_data; - - sa11xx_uda1341_audio_init(chip); - l3_command(chip->uda1341, CMD_RESUME, NULL); -#ifdef HH_VERSION - sa1100_dma_wakeup(chip->s[SNDRV_PCM_STREAM_PLAYBACK].dmach); - sa1100_dma_wakeup(chip->s[SNDRV_PCM_STREAM_CAPTURE].dmach); -#else - //FIXME -#endif - snd_power_change_state(card, SNDRV_CTL_POWER_D0); - return 0; -} -#endif /* COMFIG_PM */ - -void snd_sa11xx_uda1341_free(struct snd_card *card) -{ - struct sa11xx_uda1341 *chip = card->private_data; - - audio_dma_free(&chip->s[SNDRV_PCM_STREAM_PLAYBACK]); - audio_dma_free(&chip->s[SNDRV_PCM_STREAM_CAPTURE]); -} - -static int __devinit sa11xx_uda1341_probe(struct platform_device *devptr) -{ - int err; - struct snd_card *card; - struct sa11xx_uda1341 *chip; - - /* register the soundcard */ - err = snd_card_create(-1, id, THIS_MODULE, - sizeof(struct sa11xx_uda1341), &card); - if (err < 0) - return err; - - chip = card->private_data; - spin_lock_init(&chip->s[0].dma_lock); - spin_lock_init(&chip->s[1].dma_lock); - - card->private_free = snd_sa11xx_uda1341_free; - chip->card = card; - chip->samplerate = AUDIO_RATE_DEFAULT; - - // mixer - if ((err = snd_chip_uda1341_mixer_new(card, &chip->uda1341))) - goto nodev; - - // PCM - if ((err = snd_card_sa11xx_uda1341_pcm(chip, 0)) < 0) - goto nodev; - - strcpy(card->driver, "UDA1341"); - strcpy(card->shortname, "H3600 UDA1341TS"); - sprintf(card->longname, "Compaq iPAQ H3600 with Philips UDA1341TS"); - - snd_card_set_dev(card, &devptr->dev); - - if ((err = snd_card_register(card)) == 0) { - printk(KERN_INFO "iPAQ audio support initialized\n"); - platform_set_drvdata(devptr, card); - return 0; - } - - nodev: - snd_card_free(card); - return err; -} - -static int __devexit sa11xx_uda1341_remove(struct platform_device *devptr) -{ - snd_card_free(platform_get_drvdata(devptr)); - platform_set_drvdata(devptr, NULL); - return 0; -} - -#define SA11XX_UDA1341_DRIVER "sa11xx_uda1341" - -static struct platform_driver sa11xx_uda1341_driver = { - .probe = sa11xx_uda1341_probe, - .remove = __devexit_p(sa11xx_uda1341_remove), -#ifdef CONFIG_PM - .suspend = snd_sa11xx_uda1341_suspend, - .resume = snd_sa11xx_uda1341_resume, -#endif - .driver = { - .name = SA11XX_UDA1341_DRIVER, - }, -}; - -static int __init sa11xx_uda1341_init(void) -{ - int err; - - if (!machine_is_h3xxx()) - return -ENODEV; - if ((err = platform_driver_register(&sa11xx_uda1341_driver)) < 0) - return err; - device = platform_device_register_simple(SA11XX_UDA1341_DRIVER, -1, NULL, 0); - if (!IS_ERR(device)) { - if (platform_get_drvdata(device)) - return 0; - platform_device_unregister(device); - err = -ENODEV; - } else - err = PTR_ERR(device); - platform_driver_unregister(&sa11xx_uda1341_driver); - return err; -} - -static void __exit sa11xx_uda1341_exit(void) -{ - platform_device_unregister(device); - platform_driver_unregister(&sa11xx_uda1341_driver); -} - -module_init(sa11xx_uda1341_init); -module_exit(sa11xx_uda1341_exit); - -/* }}} */ - -/* - * Local variables: - * indent-tabs-mode: t - * End: - */ diff --git a/sound/i2c/Makefile b/sound/i2c/Makefile index 3797066..36879bf 100644 --- a/sound/i2c/Makefile +++ b/sound/i2c/Makefile @@ -7,8 +7,6 @@ snd-i2c-objs := i2c.o snd-cs8427-objs := cs8427.o snd-tea6330t-objs := tea6330t.o -obj-$(CONFIG_L3) += l3/ - obj-$(CONFIG_SND) += other/ # Toplevel Module Dependency diff --git a/sound/i2c/l3/Makefile b/sound/i2c/l3/Makefile deleted file mode 100644 index 49455b8..0000000 --- a/sound/i2c/l3/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# Makefile for ALSA -# - -snd-uda1341-objs := uda1341.o - -# Module Dependency -obj-$(CONFIG_SND_SA11XX_UDA1341) += snd-uda1341.o diff --git a/sound/i2c/l3/uda1341.c b/sound/i2c/l3/uda1341.c deleted file mode 100644 index 9840eb4..0000000 --- a/sound/i2c/l3/uda1341.c +++ /dev/null @@ -1,935 +0,0 @@ -/* - * Philips UDA1341 mixer device driver - * Copyright (c) 2002 Tomas Kasparek <tomas.kasparek(a)seznam.cz> - * - * Portions are Copyright (C) 2000 Lernout & Hauspie Speech Products, N.V. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License. - * - * History: - * - * 2002-03-13 Tomas Kasparek initial release - based on uda1341.c from OSS - * 2002-03-28 Tomas Kasparek basic mixer is working (volume, bass, treble) - * 2002-03-30 Tomas Kasparek proc filesystem support, complete mixer and DSP - * features support - * 2002-04-12 Tomas Kasparek proc interface update, code cleanup - * 2002-05-12 Tomas Kasparek another code cleanup - */ - -#include <linux/module.h> -#include <linux/init.h> -#include <linux/types.h> -#include <linux/slab.h> -#include <linux/errno.h> -#include <linux/ioctl.h> - -#include <asm/uaccess.h> - -#include <sound/core.h> -#include <sound/control.h> -#include <sound/initval.h> -#include <sound/info.h> - -#include <linux/l3/l3.h> - -#include <sound/uda1341.h> - -/* {{{ HW regs definition */ - -#define STAT0 0x00 -#define STAT1 0x80 -#define STAT_MASK 0x80 - -#define DATA0_0 0x00 -#define DATA0_1 0x40 -#define DATA0_2 0x80 -#define DATA_MASK 0xc0 - -#define IS_DATA0(x) ((x) >= data0_0 && (x) <= data0_2) -#define IS_DATA1(x) ((x) == data1) -#define IS_STATUS(x) ((x) == stat0 || (x) == stat1) -#define IS_EXTEND(x) ((x) >= ext0 && (x) <= ext6) - -/* }}} */ - - -static const char *peak_names[] = { - "before", - "after", -}; - -static const char *filter_names[] = { - "flat", - "min", - "min", - "max", -}; - -static const char *mixer_names[] = { - "double differential", - "input channel 1 (line in)", - "input channel 2 (microphone)", - "digital mixer", -}; - -static const char *deemp_names[] = { - "none", - "32 kHz", - "44.1 kHz", - "48 kHz", -}; - -enum uda1341_regs_names { - stat0, - stat1, - data0_0, - data0_1, - data0_2, - data1, - ext0, - ext1, - ext2, - empty, - ext4, - ext5, - ext6, - uda1341_reg_last, -}; - -static const char *uda1341_reg_names[] = { - "stat 0 ", - "stat 1 ", - "data 00", - "data 01", - "data 02", - "data 1 ", - "ext 0", - "ext 1", - "ext 2", - "empty", - "ext 4", - "ext 5", - "ext 6", -}; - -static const int uda1341_enum_items[] = { - 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, - 2, //peak - before/after - 4, //deemp - none/32/44.1/48 - 0, - 4, //filter - flat/min/min/max - 0, 0, 0, - 4, //mixer - differ/line/mic/mixer - 0, 0, 0, 0, 0, -}; - -static const char ** uda1341_enum_names[] = { - NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, NULL, - peak_names, //peak - before/after - deemp_names, //deemp - none/32/44.1/48 - NULL, - filter_names, //filter - flat/min/min/max - NULL, NULL, NULL, - mixer_names, //mixer - differ/line/mic/mixer - NULL, NULL, NULL, NULL, NULL, -}; - -typedef int uda1341_cfg[CMD_LAST]; - -struct uda1341 { - int (*write) (struct l3_client *uda1341, unsigned short reg, unsigned short val); - int (*read) (struct l3_client *uda1341, unsigned short reg); - unsigned char regs[uda1341_reg_last]; - int active; - spinlock_t reg_lock; - struct snd_card *card; - uda1341_cfg cfg; -#ifdef CONFIG_PM - unsigned char suspend_regs[uda1341_reg_last]; - uda1341_cfg suspend_cfg; -#endif -}; - -/* transfer 8bit integer into string with binary representation */ -static void int2str_bin8(uint8_t val, char *buf) -{ - const int size = sizeof(val) * 8; - int i; - - for (i= 0; i < size; i++){ - *(buf++) = (val >> (size - 1)) ? '1' : '0'; - val <<= 1; - } - *buf = '\0'; //end the string with zero -} - -/* {{{ HW manipulation routines */ - -static int snd_uda1341_codec_write(struct l3_client *clnt, unsigned short reg, unsigned short val) -{ - struct uda1341 *uda = clnt->driver_data; - unsigned char buf[2] = { 0xc0, 0xe0 }; // for EXT addressing - int err = 0; - - uda->regs[reg] = val; - - if (uda->active) { - if (IS_DATA0(reg)) { - err = l3_write(clnt, UDA1341_DATA0, (const unsigned char *)&val, 1); - } else if (IS_DATA1(reg)) { - err = l3_write(clnt, UDA1341_DATA1, (const unsigned char *)&val, 1); - } else if (IS_STATUS(reg)) { - err = l3_write(clnt, UDA1341_STATUS, (const unsigned char *)&val, 1); - } else if (IS_EXTEND(reg)) { - buf[0] |= (reg - ext0) & 0x7; //EXT address - buf[1] |= val; //EXT data - err = l3_write(clnt, UDA1341_DATA0, (const unsigned char *)buf, 2); - } - } else - printk(KERN_ERR "UDA1341 codec not active!\n"); - return err; -} - -static int snd_uda1341_codec_read(struct l3_client *clnt, unsigned short reg) -{ - unsigned char val; - int err; - - err = l3_read(clnt, reg, &val, 1); - if (err == 1) - // use just 6bits - the rest is address of the reg - return val & 63; - return err < 0 ? err : -EIO; -} - -static inline int snd_uda1341_valid_reg(struct l3_client *clnt, unsigned short reg) -{ - return reg < uda1341_reg_last; -} - -static int snd_uda1341_update_bits(struct l3_client *clnt, unsigned short reg, - unsigned short mask, unsigned short shift, - unsigned short value, int flush) -{ - int change; - unsigned short old, new; - struct uda1341 *uda = clnt->driver_data; - -#if 0 - printk(KERN_DEBUG "update_bits: reg: %s mask: %d shift: %d val: %d\n", - uda1341_reg_names[reg], mask, shift, value); -#endif - - if (!snd_uda1341_valid_reg(clnt, reg)) - return -EINVAL; - spin_lock(&uda->reg_lock); - old = uda->regs[reg]; - new = (old & ~(mask << shift)) | (value << shift); - change = old != new; - if (change) { - if (flush) uda->write(clnt, reg, new); - uda->regs[reg] = new; - } - spin_unlock(&uda->reg_lock); - return change; -} - -static int snd_uda1341_cfg_write(struct l3_client *clnt, unsigned short what, - unsigned short value, int flush) -{ - struct uda1341 *uda = clnt->driver_data; - int ret = 0; -#ifdef CONFIG_PM - int reg; -#endif - -#if 0 - printk(KERN_DEBUG "cfg_write what: %d value: %d\n", what, value); -#endif - - uda->cfg[what] = value; - - switch(what) { - case CMD_RESET: - ret = snd_uda1341_update_bits(clnt, data0_2, 1, 2, 1, flush); // MUTE - ret = snd_uda1341_update_bits(clnt, stat0, 1, 6, 1, flush); // RESET - ret = snd_uda1341_update_bits(clnt, stat0, 1, 6, 0, flush); // RESTORE - uda->cfg[CMD_RESET]=0; - break; - case CMD_FS: - ret = snd_uda1341_update_bits(clnt, stat0, 3, 4, value, flush); - break; - case CMD_FORMAT: - ret = snd_uda1341_update_bits(clnt, stat0, 7, 1, value, flush); - break; - case CMD_OGAIN: - ret = snd_uda1341_update_bits(clnt, stat1, 1, 6, value, flush); - break; - case CMD_IGAIN: - ret = snd_uda1341_update_bits(clnt, stat1, 1, 5, value, flush); - break; - case CMD_DAC: - ret = snd_uda1341_update_bits(clnt, stat1, 1, 0, value, flush); - break; - case CMD_ADC: - ret = snd_uda1341_update_bits(clnt, stat1, 1, 1, value, flush); - break; - case CMD_VOLUME: - ret = snd_uda1341_update_bits(clnt, data0_0, 63, 0, value, flush); - break; - case CMD_BASS: - ret = snd_uda1341_update_bits(clnt, data0_1, 15, 2, value, flush); - break; - case CMD_TREBBLE: - ret = snd_uda1341_update_bits(clnt, data0_1, 3, 0, value, flush); - break; - case CMD_PEAK: - ret = snd_uda1341_update_bits(clnt, data0_2, 1, 5, value, flush); - break; - case CMD_DEEMP: - ret = snd_uda1341_update_bits(clnt, data0_2, 3, 3, value, flush); - break; - case CMD_MUTE: - ret = snd_uda1341_update_bits(clnt, data0_2, 1, 2, value, flush); - break; - case CMD_FILTER: - ret = snd_uda1341_update_bits(clnt, data0_2, 3, 0, value, flush); - break; - case CMD_CH1: - ret = snd_uda1341_update_bits(clnt, ext0, 31, 0, value, flush); - break; - case CMD_CH2: - ret = snd_uda1341_update_bits(clnt, ext1, 31, 0, value, flush); - break; - case CMD_MIC: - ret = snd_uda1341_update_bits(clnt, ext2, 7, 2, value, flush); - break; - case CMD_MIXER: - ret = snd_uda1341_update_bits(clnt, ext2, 3, 0, value, flush); - break; - case CMD_AGC: - ret = snd_uda1341_update_bits(clnt, ext4, 1, 4, value, flush); - break; - case CMD_IG: - ret = snd_uda1341_update_bits(clnt, ext4, 3, 0, value & 0x3, flush); - ret = snd_uda1341_update_bits(clnt, ext5, 31, 0, value >> 2, flush); - break; - case CMD_AGC_TIME: - ret = snd_uda1341_update_bits(clnt, ext6, 7, 2, value, flush); - break; - case CMD_AGC_LEVEL: - ret = snd_uda1341_update_bits(clnt, ext6, 3, 0, value, flush); - break; -#ifdef CONFIG_PM - case CMD_SUSPEND: - for (reg = stat0; reg < uda1341_reg_last; reg++) - uda->suspend_regs[reg] = uda->regs[reg]; - for (reg = 0; reg < CMD_LAST; reg++) - uda->suspend_cfg[reg] = uda->cfg[reg]; - break; - case CMD_RESUME: - for (reg = stat0; reg < uda1341_reg_last; reg++) - snd_uda1341_codec_write(clnt, reg, uda->suspend_regs[reg]); - for (reg = 0; reg < CMD_LAST; reg++) - uda->cfg[reg] = uda->suspend_cfg[reg]; - break; -#endif - default: - ret = -EINVAL; - break; - } - - if (!uda->active) - printk(KERN_ERR "UDA1341 codec not active!\n"); - return ret; -} - -/* }}} */ - -/* {{{ Proc interface */ -#ifdef CONFIG_PROC_FS - -static const char *format_names[] = { - "I2S-bus", - "LSB 16bits", - "LSB 18bits", - "LSB 20bits", - "MSB", - "in LSB 16bits/out MSB", - "in LSB 18bits/out MSB", - "in LSB 20bits/out MSB", -}; - -static const char *fs_names[] = { - "512*fs", - "384*fs", - "256*fs", - "Unused - bad value!", -}; - -static const char* bass_values[][16] = { - {"0 dB", "0 dB", "0 dB", "0 dB", "0 dB", "0 dB", "0 dB", "0 dB", "0 dB", "0 dB", "0 dB", - "0 dB", "0 dB", "0 dB", "0 dB", "undefined", }, //flat - {"0 dB", "2 dB", "4 dB", "6 dB", "8 dB", "10 dB", "12 dB", "14 dB", "16 dB", "18 dB", "18 dB", - "18 dB", "18 dB", "18 dB", "18 dB", "undefined",}, // min - {"0 dB", "2 dB", "4 dB", "6 dB", "8 dB", "10 dB", "12 dB", "14 dB", "16 dB", "18 dB", "18 dB", - "18 dB", "18 dB", "18 dB", "18 dB", "undefined",}, // min - {"0 dB", "2 dB", "4 dB", "6 dB", "8 dB", "10 dB", "12 dB", "14 dB", "16 dB", "18 dB", "20 dB", - "22 dB", "24 dB", "24 dB", "24 dB", "undefined",}, // max -}; - -static const char *mic_sens_value[] = { - "-3 dB", "0 dB", "3 dB", "9 dB", "15 dB", "21 dB", "27 dB", "not used", -}; - -static const unsigned short AGC_atime[] = { - 11, 16, 11, 16, 21, 11, 16, 21, -}; - -static const unsigned short AGC_dtime[] = { - 100, 100, 200, 200, 200, 400, 400, 400, -}; - -static const char *AGC_level[] = { - "-9.0", "-11.5", "-15.0", "-17.5", -}; - -static const char *ig_small_value[] = { - "-3.0", "-2.5", "-2.0", "-1.5", "-1.0", "-0.5", -}; - -/* - * this was computed as peak_value[i] = pow((63-i)*1.42,1.013) - * - * UDA1341 datasheet on page 21: Peak value (dB) = (Peak level - 63.5)*5*log2 - * There is an table with these values [level]=value: [3]=-90.31, [7]=-84.29 - * [61]=-2.78, [62] = -1.48, [63] = 0.0 - * I tried to compute it, but using but even using logarithm with base either 10 or 2 - * i was'n able to get values in the table from the formula. So I constructed another - * formula (see above) to interpolate the values as good as possible. If there is some - * mistake, please contact me on tomas.kasparek(a)seznam.cz. Thanks. - * UDA1341TS datasheet is available at: - * http://www-us9.semiconductors.com/acrobat/datasheets/UDA1341TS_3.pdf - */ -static const char *peak_value[] = { - "-INF dB", "N.A.", "N.A", "90.31 dB", "N.A.", "N.A.", "N.A.", "-84.29 dB", - "-82.65 dB", "-81.13 dB", "-79.61 dB", "-78.09 dB", "-76.57 dB", "-75.05 dB", "-73.53 dB", - "-72.01 dB", "-70.49 dB", "-68.97 dB", "-67.45 dB", "-65.93 dB", "-64.41 dB", "-62.90 dB", - "-61.38 dB", "-59.86 dB", "-58.35 dB", "-56.83 dB", "-55.32 dB", "-53.80 dB", "-52.29 dB", - "-50.78 dB", "-49.26 dB", "-47.75 dB", "-46.24 dB", "-44.73 dB", "-43.22 dB", "-41.71 dB", - "-40.20 dB", "-38.69 dB", "-37.19 dB", "-35.68 dB", "-34.17 dB", "-32.67 dB", "-31.17 dB", - "-29.66 dB", "-28.16 dB", "-26.66 dB", "-25.16 dB", "-23.66 dB", "-22.16 dB", "-20.67 dB", - "-19.17 dB", "-17.68 dB", "-16.19 dB", "-14.70 dB", "-13.21 dB", "-11.72 dB", "-10.24 dB", - "-8.76 dB", "-7.28 dB", "-5.81 dB", "-4.34 dB", "-2.88 dB", "-1.43 dB", "0.00 dB", -}; - -static void snd_uda1341_proc_read(struct snd_info_entry *entry, - struct snd_info_buffer *buffer) -{ - struct l3_client *clnt = entry->private_data; - struct uda1341 *uda = clnt->driver_data; - int peak; - - peak = snd_uda1341_codec_read(clnt, UDA1341_DATA1); - if (peak < 0) - peak = 0; - - snd_iprintf(buffer, "%s\n\n", uda->card->longname); - - // for information about computed values see UDA1341TS datasheet pages 15 - 21 - snd_iprintf(buffer, "DAC power : %s\n", uda->cfg[CMD_DAC] ? "on" : "off"); - snd_iprintf(buffer, "ADC power : %s\n", uda->cfg[CMD_ADC] ? "on" : "off"); - snd_iprintf(buffer, "Clock frequency : %s\n", fs_names[uda->cfg[CMD_FS]]); - snd_iprintf(buffer, "Data format : %s\n\n", format_names[uda->cfg[CMD_FORMAT]]); - - snd_iprintf(buffer, "Filter mode : %s\n", filter_names[uda->cfg[CMD_FILTER]]); - snd_iprintf(buffer, "Mixer mode : %s\n", mixer_names[uda->cfg[CMD_MIXER]]); - snd_iprintf(buffer, "De-emphasis : %s\n", deemp_names[uda->cfg[CMD_DEEMP]]); - snd_iprintf(buffer, "Peak detection pos. : %s\n", uda->cfg[CMD_PEAK] ? "after" : "before"); - snd_iprintf(buffer, "Peak value : %s\n\n", peak_value[peak]); - - snd_iprintf(buffer, "Automatic Gain Ctrl : %s\n", uda->cfg[CMD_AGC] ? "on" : "off"); - snd_iprintf(buffer, "AGC attack time : %d ms\n", AGC_atime[uda->cfg[CMD_AGC_TIME]]); - snd_iprintf(buffer, "AGC decay time : %d ms\n", AGC_dtime[uda->cfg[CMD_AGC_TIME]]); - snd_iprintf(buffer, "AGC output level : %s dB\n\n", AGC_level[uda->cfg[CMD_AGC_LEVEL]]); - - snd_iprintf(buffer, "Mute : %s\n", uda->cfg[CMD_MUTE] ? "on" : "off"); - - if (uda->cfg[CMD_VOLUME] == 0) - snd_iprintf(buffer, "Volume : 0 dB\n"); - else if (uda->cfg[CMD_VOLUME] < 62) - snd_iprintf(buffer, "Volume : %d dB\n", -1*uda->cfg[CMD_VOLUME] +1); - else - snd_iprintf(buffer, "Volume : -INF dB\n"); - snd_iprintf(buffer, "Bass : %s\n", bass_values[uda->cfg[CMD_FILTER]][uda->cfg[CMD_BASS]]); - snd_iprintf(buffer, "Trebble : %d dB\n", uda->cfg[CMD_FILTER] ? 2*uda->cfg[CMD_TREBBLE] : 0); - snd_iprintf(buffer, "Input Gain (6dB) : %s\n", uda->cfg[CMD_IGAIN] ? "on" : "off"); - snd_iprintf(buffer, "Output Gain (6dB) : %s\n", uda->cfg[CMD_OGAIN] ? "on" : "off"); - snd_iprintf(buffer, "Mic sensitivity : %s\n", mic_sens_value[uda->cfg[CMD_MIC]]); - - - if(uda->cfg[CMD_CH1] < 31) - snd_iprintf(buffer, "Mixer gain channel 1: -%d.%c dB\n", - ((uda->cfg[CMD_CH1] >> 1) * 3) + (uda->cfg[CMD_CH1] & 1), - uda->cfg[CMD_CH1] & 1 ? '5' : '0'); - else - snd_iprintf(buffer, "Mixer gain channel 1: -INF dB\n"); - if(uda->cfg[CMD_CH2] < 31) - snd_iprintf(buffer, "Mixer gain channel 2: -%d.%c dB\n", - ((uda->cfg[CMD_CH2] >> 1) * 3) + (uda->cfg[CMD_CH2] & 1), - uda->cfg[CMD_CH2] & 1 ? '5' : '0'); - else - snd_iprintf(buffer, "Mixer gain channel 2: -INF dB\n"); - - if(uda->cfg[CMD_IG] > 5) - snd_iprintf(buffer, "Input Amp. Gain ch 2: %d.%c dB\n", - (uda->cfg[CMD_IG] >> 1) -3, uda->cfg[CMD_IG] & 1 ? '5' : '0'); - else - snd_iprintf(buffer, "Input Amp. Gain ch 2: %s dB\n", ig_small_value[uda->cfg[CMD_IG]]); -} - -static void snd_uda1341_proc_regs_read(struct snd_info_entry *entry, - struct snd_info_buffer *buffer) -{ - struct l3_client *clnt = entry->private_data; - struct uda1341 *uda = clnt->driver_data; - int reg; - char buf[12]; - - for (reg = 0; reg < uda1341_reg_last; reg ++) { - if (reg == empty) - continue; - int2str_bin8(uda->regs[reg], buf); - snd_iprintf(buffer, "%s = %s\n", uda1341_reg_names[reg], buf); - } - - int2str_bin8(snd_uda1341_codec_read(clnt, UDA1341_DATA1), buf); - snd_iprintf(buffer, "DATA1 = %s\n", buf); -} -#endif /* CONFIG_PROC_FS */ - -static void __devinit snd_uda1341_proc_init(struct snd_card *card, struct l3_client *clnt) -{ - struct snd_info_entry *entry; - - if (! snd_card_proc_new(card, "uda1341", &entry)) - snd_info_set_text_ops(entry, clnt, snd_uda1341_proc_read); - if (! snd_card_proc_new(card, "uda1341-regs", &entry)) - snd_info_set_text_ops(entry, clnt, snd_uda1341_proc_regs_read); -} - -/* }}} */ - -/* {{{ Mixer controls setting */ - -/* {{{ UDA1341 single functions */ - -#define UDA1341_SINGLE(xname, where, reg, shift, mask, invert) \ -{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = xname, .info = snd_uda1341_info_single, \ - .get = snd_uda1341_get_single, .put = snd_uda1341_put_single, \ - .private_value = where | (reg << 5) | (shift << 9) | (mask << 12) | (invert << 18) \ -} - -static int snd_uda1341_info_single(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_info *uinfo) -{ - int mask = (kcontrol->private_value >> 12) & 63; - - uinfo->type = mask == 1 ? SNDRV_CTL_ELEM_TYPE_BOOLEAN : SNDRV_CTL_ELEM_TYPE_INTEGER; - uinfo->count = 1; - uinfo->value.integer.min = 0; - uinfo->value.integer.max = mask; - return 0; -} - -static int snd_uda1341_get_single(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_value *ucontrol) -{ - struct l3_client *clnt = snd_kcontrol_chip(kcontrol); - struct uda1341 *uda = clnt->driver_data; - int where = kcontrol->private_value & 31; - int mask = (kcontrol->private_value >> 12) & 63; - int invert = (kcontrol->private_value >> 18) & 1; - - ucontrol->value.integer.value[0] = uda->cfg[where]; - if (invert) - ucontrol->value.integer.value[0] = mask - ucontrol->value.integer.value[0]; - - return 0; -} - -static int snd_uda1341_put_single(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_value *ucontrol) -{ - struct l3_client *clnt = snd_kcontrol_chip(kcontrol); - struct uda1341 *uda = clnt->driver_data; - int where = kcontrol->private_value & 31; - int reg = (kcontrol->private_value >> 5) & 15; - int shift = (kcontrol->private_value >> 9) & 7; - int mask = (kcontrol->private_value >> 12) & 63; - int invert = (kcontrol->private_value >> 18) & 1; - unsigned short val; - - val = (ucontrol->value.integer.value[0] & mask); - if (invert) - val = mask - val; - - uda->cfg[where] = val; - return snd_uda1341_update_bits(clnt, reg, mask, shift, val, FLUSH); -} - -/* }}} */ - -/* {{{ UDA1341 enum functions */ - -#define UDA1341_ENUM(xname, where, reg, shift, mask, invert) \ -{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = xname, .info = snd_uda1341_info_enum, \ - .get = snd_uda1341_get_enum, .put = snd_uda1341_put_enum, \ - .private_value = where | (reg << 5) | (shift << 9) | (mask << 12) | (invert << 18) \ -} - -static int snd_uda1341_info_enum(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_info *uinfo) -{ - int where = kcontrol->private_value & 31; - const char **texts; - - // this register we don't handle this way - if (!uda1341_enum_items[where]) - return -EINVAL; - - uinfo->type = SNDRV_CTL_ELEM_TYPE_ENUMERATED; - uinfo->count = 1; - uinfo->value.enumerated.items = uda1341_enum_items[where]; - - if (uinfo->value.enumerated.item >= uda1341_enum_items[where]) - uinfo->value.enumerated.item = uda1341_enum_items[where] - 1; - - texts = uda1341_enum_names[where]; - strcpy(uinfo->value.enumerated.name, texts[uinfo->value.enumerated.item]); - return 0; -} - -static int snd_uda1341_get_enum(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_value *ucontrol) -{ - struct l3_client *clnt = snd_kcontrol_chip(kcontrol); - struct uda1341 *uda = clnt->driver_data; - int where = kcontrol->private_value & 31; - - ucontrol->value.enumerated.item[0] = uda->cfg[where]; - return 0; -} - -static int snd_uda1341_put_enum(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_value *ucontrol) -{ - struct l3_client *clnt = snd_kcontrol_chip(kcontrol); - struct uda1341 *uda = clnt->driver_data; - int where = kcontrol->private_value & 31; - int reg = (kcontrol->private_value >> 5) & 15; - int shift = (kcontrol->private_value >> 9) & 7; - int mask = (kcontrol->private_value >> 12) & 63; - - uda->cfg[where] = (ucontrol->value.enumerated.item[0] & mask); - - return snd_uda1341_update_bits(clnt, reg, mask, shift, uda->cfg[where], FLUSH); -} - -/* }}} */ - -/* {{{ UDA1341 2regs functions */ - -#define UDA1341_2REGS(xname, where, reg_1, reg_2, shift_1, shift_2, mask_1, mask_2, invert) \ -{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname), .info = snd_uda1341_info_2regs, \ - .get = snd_uda1341_get_2regs, .put = snd_uda1341_put_2regs, \ - .private_value = where | (reg_1 << 5) | (reg_2 << 9) | (shift_1 << 13) | (shift_2 << 16) | \ - (mask_1 << 19) | (mask_2 << 25) | (invert << 31) \ -} - - -static int snd_uda1341_info_2regs(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_info *uinfo) -{ - int mask_1 = (kcontrol->private_value >> 19) & 63; - int mask_2 = (kcontrol->private_value >> 25) & 63; - int mask; - - mask = (mask_2 + 1) * (mask_1 + 1) - 1; - uinfo->type = mask == 1 ? SNDRV_CTL_ELEM_TYPE_BOOLEAN : SNDRV_CTL_ELEM_TYPE_INTEGER; - uinfo->count = 1; - uinfo->value.integer.min = 0; - uinfo->value.integer.max = mask; - return 0; -} - -static int snd_uda1341_get_2regs(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_value *ucontrol) -{ - struct l3_client *clnt = snd_kcontrol_chip(kcontrol); - struct uda1341 *uda = clnt->driver_data; - int where = kcontrol->private_value & 31; - int mask_1 = (kcontrol->private_value >> 19) & 63; - int mask_2 = (kcontrol->private_value >> 25) & 63; - int invert = (kcontrol->private_value >> 31) & 1; - int mask; - - mask = (mask_2 + 1) * (mask_1 + 1) - 1; - - ucontrol->value.integer.value[0] = uda->cfg[where]; - if (invert) - ucontrol->value.integer.value[0] = mask - ucontrol->value.integer.value[0]; - return 0; -} - -static int snd_uda1341_put_2regs(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_value *ucontrol) -{ - struct l3_client *clnt = snd_kcontrol_chip(kcontrol); - struct uda1341 *uda = clnt->driver_data; - int where = kcontrol->private_value & 31; - int reg_1 = (kcontrol->private_value >> 5) & 15; - int reg_2 = (kcontrol->private_value >> 9) & 15; - int shift_1 = (kcontrol->private_value >> 13) & 7; - int shift_2 = (kcontrol->private_value >> 16) & 7; - int mask_1 = (kcontrol->private_value >> 19) & 63; - int mask_2 = (kcontrol->private_value >> 25) & 63; - int invert = (kcontrol->private_value >> 31) & 1; - int mask; - unsigned short val1, val2, val; - - val = ucontrol->value.integer.value[0]; - - mask = (mask_2 + 1) * (mask_1 + 1) - 1; - - val1 = val & mask_1; - val2 = (val / (mask_1 + 1)) & mask_2; - - if (invert) { - val1 = mask_1 - val1; - val2 = mask_2 - val2; - } - - uda->cfg[where] = invert ? mask - val : val; - - //FIXME - return value - snd_uda1341_update_bits(clnt, reg_1, mask_1, shift_1, val1, FLUSH); - return snd_uda1341_update_bits(clnt, reg_2, mask_2, shift_2, val2, FLUSH); -} - -/* }}} */ - -static struct snd_kcontrol_new snd_uda1341_controls[] = { - UDA1341_SINGLE("Master Playback Switch", CMD_MUTE, data0_2, 2, 1, 1), - UDA1341_SINGLE("Master Playback Volume", CMD_VOLUME, data0_0, 0, 63, 1), - - UDA1341_SINGLE("Bass Playback Volume", CMD_BASS, data0_1, 2, 15, 0), - UDA1341_SINGLE("Treble Playback Volume", CMD_TREBBLE, data0_1, 0, 3, 0), - - UDA1341_SINGLE("Input Gain Switch", CMD_IGAIN, stat1, 5, 1, 0), - UDA1341_SINGLE("Output Gain Switch", CMD_OGAIN, stat1, 6, 1, 0), - - UDA1341_SINGLE("Mixer Gain Channel 1 Volume", CMD_CH1, ext0, 0, 31, 1), - UDA1341_SINGLE("Mixer Gain Channel 2 Volume", CMD_CH2, ext1, 0, 31, 1), - - UDA1341_SINGLE("Mic Sensitivity Volume", CMD_MIC, ext2, 2, 7, 0), - - UDA1341_SINGLE("AGC Output Level", CMD_AGC_LEVEL, ext6, 0, 3, 0), - UDA1341_SINGLE("AGC Time Constant", CMD_AGC_TIME, ext6, 2, 7, 0), - UDA1341_SINGLE("AGC Time Constant Switch", CMD_AGC, ext4, 4, 1, 0), - - UDA1341_SINGLE("DAC Power", CMD_DAC, stat1, 0, 1, 0), - UDA1341_SINGLE("ADC Power", CMD_ADC, stat1, 1, 1, 0), - - UDA1341_ENUM("Peak detection", CMD_PEAK, data0_2, 5, 1, 0), - UDA1341_ENUM("De-emphasis", CMD_DEEMP, data0_2, 3, 3, 0), - UDA1341_ENUM("Mixer mode", CMD_MIXER, ext2, 0, 3, 0), - UDA1341_ENUM("Filter mode", CMD_FILTER, data0_2, 0, 3, 0), - - UDA1341_2REGS("Gain Input Amplifier Gain (channel 2)", CMD_IG, ext4, ext5, 0, 0, 3, 31, 0), -}; - -static void uda1341_free(struct l3_client *clnt) -{ - l3_detach_client(clnt); // calls kfree for driver_data (struct uda1341) - kfree(clnt); -} - -static int uda1341_dev_free(struct snd_device *device) -{ - struct l3_client *clnt = device->device_data; - uda1341_free(clnt); - return 0; -} - -int __init snd_chip_uda1341_mixer_new(struct snd_card *card, struct l3_client **clntp) -{ - static struct snd_device_ops ops = { - .dev_free = uda1341_dev_free, - }; - struct l3_client *clnt; - int idx, err; - - if (snd_BUG_ON(!card)) - return -EINVAL; - - clnt = kzalloc(sizeof(*clnt), GFP_KERNEL); - if (clnt == NULL) - return -ENOMEM; - - if ((err = l3_attach_client(clnt, "l3-bit-sa1100-gpio", UDA1341_ALSA_NAME))) { - kfree(clnt); - return err; - } - - for (idx = 0; idx < ARRAY_SIZE(snd_uda1341_controls); idx++) { - if ((err = snd_ctl_add(card, snd_ctl_new1(&snd_uda1341_controls[idx], clnt))) < 0) { - uda1341_free(clnt); - return err; - } - } - - if ((err = snd_device_new(card, SNDRV_DEV_CODEC, clnt, &ops)) < 0) { - uda1341_free(clnt); - return err; - } - - *clntp = clnt; - strcpy(card->mixername, "UDA1341TS Mixer"); - ((struct uda1341 *)clnt->driver_data)->card = card; - - snd_uda1341_proc_init(card, clnt); - - return 0; -} - -/* }}} */ - -/* {{{ L3 operations */ - -static int uda1341_attach(struct l3_client *clnt) -{ - struct uda1341 *uda; - - uda = kzalloc(sizeof(*uda), 0, GFP_KERNEL); - if (!uda) - return -ENOMEM; - - /* init fixed parts of my copy of registers */ - uda->regs[stat0] = STAT0; - uda->regs[stat1] = STAT1; - - uda->regs[data0_0] = DATA0_0; - uda->regs[data0_1] = DATA0_1; - uda->regs[data0_2] = DATA0_2; - - uda->write = snd_uda1341_codec_write; - uda->read = snd_uda1341_codec_read; - - spin_lock_init(&uda->reg_lock); - - clnt->driver_data = uda; - return 0; -} - -static void uda1341_detach(struct l3_client *clnt) -{ - kfree(clnt->driver_data); -} - -static int -uda1341_command(struct l3_client *clnt, int cmd, void *arg) -{ - if (cmd != CMD_READ_REG) - return snd_uda1341_cfg_write(clnt, cmd, (int) arg, FLUSH); - - return snd_uda1341_codec_read(clnt, (int) arg); -} - -static int uda1341_open(struct l3_client *clnt) -{ - struct uda1341 *uda = clnt->driver_data; - - uda->active = 1; - - /* init default configuration */ - snd_uda1341_cfg_write(clnt, CMD_RESET, 0, REGS_ONLY); - snd_uda1341_cfg_write(clnt, CMD_FS, F256, FLUSH); // unknown state after reset - snd_uda1341_cfg_write(clnt, CMD_FORMAT, LSB16, FLUSH); // unknown state after reset - snd_uda1341_cfg_write(clnt, CMD_OGAIN, ON, FLUSH); // default off after reset - snd_uda1341_cfg_write(clnt, CMD_IGAIN, ON, FLUSH); // default off after reset - snd_uda1341_cfg_write(clnt, CMD_DAC, ON, FLUSH); // ??? default value after reset - snd_uda1341_cfg_write(clnt, CMD_ADC, ON, FLUSH); // ??? default value after reset - snd_uda1341_cfg_write(clnt, CMD_VOLUME, 20, FLUSH); // default 0dB after reset - snd_uda1341_cfg_write(clnt, CMD_BASS, 0, REGS_ONLY); // default value after reset - snd_uda1341_cfg_write(clnt, CMD_TREBBLE, 0, REGS_ONLY); // default value after reset - snd_uda1341_cfg_write(clnt, CMD_PEAK, AFTER, REGS_ONLY);// default value after reset - snd_uda1341_cfg_write(clnt, CMD_DEEMP, NONE, REGS_ONLY);// default value after reset - //at this moment should be QMUTED by h3600_audio_init - snd_uda1341_cfg_write(clnt, CMD_MUTE, OFF, REGS_ONLY); // default value after reset - snd_uda1341_cfg_write(clnt, CMD_FILTER, MAX, FLUSH); // defaul flat after reset - snd_uda1341_cfg_write(clnt, CMD_CH1, 31, FLUSH); // default value after reset - snd_uda1341_cfg_write(clnt, CMD_CH2, 4, FLUSH); // default value after reset - snd_uda1341_cfg_write(clnt, CMD_MIC, 4, FLUSH); // default 0dB after reset - snd_uda1341_cfg_write(clnt, CMD_MIXER, MIXER, FLUSH); // default doub.dif.mode - snd_uda1341_cfg_write(clnt, CMD_AGC, OFF, FLUSH); // default value after reset - snd_uda1341_cfg_write(clnt, CMD_IG, 0, FLUSH); // unknown state after reset - snd_uda1341_cfg_write(clnt, CMD_AGC_TIME, 0, FLUSH); // default value after reset - snd_uda1341_cfg_write(clnt, CMD_AGC_LEVEL, 0, FLUSH); // default value after reset - - return 0; -} - -static void uda1341_close(struct l3_client *clnt) -{ - struct uda1341 *uda = clnt->driver_data; - - uda->active = 0; -} - -/* }}} */ - -/* {{{ Module and L3 initialization */ - -static struct l3_ops uda1341_ops = { - .open = uda1341_open, - .command = uda1341_command, - .close = uda1341_close, -}; - -static struct l3_driver uda1341_driver = { - .name = UDA1341_ALSA_NAME, - .attach_client = uda1341_attach, - .detach_client = uda1341_detach, - .ops = &uda1341_ops, - .owner = THIS_MODULE, -}; - -static int __init uda1341_init(void) -{ - return l3_add_driver(&uda1341_driver); -} - -static void __exit uda1341_exit(void) -{ - l3_del_driver(&uda1341_driver); -} - -module_init(uda1341_init); -module_exit(uda1341_exit); - -MODULE_AUTHOR("Tomas Kasparek <tomas.kasparek(a)seznam.cz>"); -MODULE_LICENSE("GPL"); -MODULE_DESCRIPTION("Philips UDA1341 CODEC driver for ALSA"); -MODULE_SUPPORTED_DEVICE("{{UDA1341,UDA1341TS}}"); - -EXPORT_SYMBOL(snd_chip_uda1341_mixer_new); - -/* }}} */ - -/* - * Local variables: - * indent-tabs-mode: t - * End: - */ -- 1.6.1.3 -- Best regards, Dmitry "MAD" Artamonow

1 0