- Alsa-devel - mailman.alsa-project.org

[PATCH 0/2] ASoC: SOF: pcm/Intel: Pause-resume improvements for IPC4
by Peter Ujfalusi 21 Apr '23

21 Apr '23

Hi, last minute patch for correct the pasue/resume operation with IPC4. The issues are hardto reproduce and needs extended stress testing to be hit, in which case the audio breaks due to DMA errors. Regards, Peter --- Ranjani Sridharan (2): ASoC: SOF: Intel: hda: Do not stop/start DMA during pause/release ASoC: SOF: pcm: Add an option to skip platform trigger during stop sound/soc/sof/intel/hda-stream.c | 11 ++++++++++- sound/soc/sof/ipc4-pcm.c | 3 ++- sound/soc/sof/pcm.c | 23 +++++++++++++++-------- sound/soc/sof/sof-audio.c | 22 ++++++++++++++-------- sound/soc/sof/sof-audio.h | 6 ++++++ 5 files changed, 47 insertions(+), 18 deletions(-) -- 2.40.0

2 3

[PATCH] ASoC: SOF: Intel: Split the set_power_op for IPC3 and IPC4
by Peter Ujfalusi 21 Apr '23

21 Apr '23

From: Ranjani Sridharan <ranjani.sridharan(a)linux.intel.com> Suspending to S0iX with IPC3 requires the PM_GATE IPC to be sent again to stop the DMA trace. But with IPC4, this is not needed as the trace is stopped with the LARGE_CONFIG_SET IPC. Also, sending the MOD_D0IX IPC to set the D0I3 state again when the DSP is in D0I3 already results in an imbalance in PM runtime states in the firmware. So split the set_power_state ops for IPC3 and IPC4 to avoid sending the MOD_D0IX IPC when the DSP is already in D0I3 with IPC4. Signed-off-by: Ranjani Sridharan <ranjani.sridharan(a)linux.intel.com> Reviewed-by: Rander Wang <rander.wang(a)intel.com> Reviewed-by: Bard Liao <yung-chuan.liao(a)linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi(a)linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart(a)linux.intel.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi(a)linux.intel.com> --- Mark, last minute patch for 6.4 as the issue this patch addressing was discovered and fixed recently for IPC4. Regards, Peter sound/soc/sof/intel/apl.c | 4 ++ sound/soc/sof/intel/cnl.c | 4 ++ sound/soc/sof/intel/hda-common-ops.c | 1 - sound/soc/sof/intel/hda-dsp.c | 60 ++++++++++++++++++---------- sound/soc/sof/intel/hda.h | 6 ++- sound/soc/sof/intel/icl.c | 4 ++ sound/soc/sof/intel/mtl.c | 2 + sound/soc/sof/intel/tgl.c | 4 ++ 8 files changed, 60 insertions(+), 25 deletions(-) diff --git a/sound/soc/sof/intel/apl.c b/sound/soc/sof/intel/apl.c index 0e7a7e4ad976..e1f25a8f0c32 100644 --- a/sound/soc/sof/intel/apl.c +++ b/sound/soc/sof/intel/apl.c @@ -48,6 +48,8 @@ int sof_apl_ops_init(struct snd_sof_dev *sdev) /* debug */ sof_apl_ops.ipc_dump = hda_ipc_dump; + + sof_apl_ops.set_power_state = hda_dsp_set_power_state_ipc3; } if (sdev->pdata->ipc_type == SOF_INTEL_IPC4) { @@ -73,6 +75,8 @@ int sof_apl_ops_init(struct snd_sof_dev *sdev) /* debug */ sof_apl_ops.ipc_dump = hda_ipc4_dump; + + sof_apl_ops.set_power_state = hda_dsp_set_power_state_ipc4; } /* set DAI driver ops */ diff --git a/sound/soc/sof/intel/cnl.c b/sound/soc/sof/intel/cnl.c index a08a77fa946b..a95222e53ecf 100644 --- a/sound/soc/sof/intel/cnl.c +++ b/sound/soc/sof/intel/cnl.c @@ -395,6 +395,8 @@ int sof_cnl_ops_init(struct snd_sof_dev *sdev) /* debug */ sof_cnl_ops.ipc_dump = cnl_ipc_dump; + + sof_cnl_ops.set_power_state = hda_dsp_set_power_state_ipc3; } if (sdev->pdata->ipc_type == SOF_INTEL_IPC4) { @@ -420,6 +422,8 @@ int sof_cnl_ops_init(struct snd_sof_dev *sdev) /* debug */ sof_cnl_ops.ipc_dump = cnl_ipc4_dump; + + sof_cnl_ops.set_power_state = hda_dsp_set_power_state_ipc4; } /* set DAI driver ops */ diff --git a/sound/soc/sof/intel/hda-common-ops.c b/sound/soc/sof/intel/hda-common-ops.c index 397303b3ac9d..8e1cd0babd32 100644 --- a/sound/soc/sof/intel/hda-common-ops.c +++ b/sound/soc/sof/intel/hda-common-ops.c @@ -89,7 +89,6 @@ struct snd_sof_dsp_ops sof_hda_common_ops = { .runtime_resume = hda_dsp_runtime_resume, .runtime_idle = hda_dsp_runtime_idle, .set_hw_params_upon_resume = hda_dsp_set_hw_params_upon_resume, - .set_power_state = hda_dsp_set_power_state, /* ALSA HW info flags */ .hw_info = SNDRV_PCM_INFO_MMAP | diff --git a/sound/soc/sof/intel/hda-dsp.c b/sound/soc/sof/intel/hda-dsp.c index 77df536cf901..44f39a520bb3 100644 --- a/sound/soc/sof/intel/hda-dsp.c +++ b/sound/soc/sof/intel/hda-dsp.c @@ -574,31 +574,11 @@ static void hda_dsp_state_log(struct snd_sof_dev *sdev) * is called again either because of a new IPC sent to the DSP or * during system suspend/resume. */ -int hda_dsp_set_power_state(struct snd_sof_dev *sdev, - const struct sof_dsp_power_state *target_state) +static int hda_dsp_set_power_state(struct snd_sof_dev *sdev, + const struct sof_dsp_power_state *target_state) { int ret = 0; - /* - * When the DSP is already in D0I3 and the target state is D0I3, - * it could be the case that the DSP is in D0I3 during S0 - * and the system is suspending to S0Ix. Therefore, - * hda_dsp_set_D0_state() must be called to disable trace DMA - * by sending the PM_GATE IPC to the FW. - */ - if (target_state->substate == SOF_HDA_DSP_PM_D0I3 && - sdev->system_suspend_target == SOF_SUSPEND_S0IX) - goto set_state; - - /* - * For all other cases, return without doing anything if - * the DSP is already in the target state. - */ - if (target_state->state == sdev->dsp_power_state.state && - target_state->substate == sdev->dsp_power_state.substate) - return 0; - -set_state: switch (target_state->state) { case SOF_DSP_PM_D0: ret = hda_dsp_set_D0_state(sdev, target_state); @@ -630,6 +610,42 @@ int hda_dsp_set_power_state(struct snd_sof_dev *sdev, return ret; } +int hda_dsp_set_power_state_ipc3(struct snd_sof_dev *sdev, + const struct sof_dsp_power_state *target_state) +{ + /* + * When the DSP is already in D0I3 and the target state is D0I3, + * it could be the case that the DSP is in D0I3 during S0 + * and the system is suspending to S0Ix. Therefore, + * hda_dsp_set_D0_state() must be called to disable trace DMA + * by sending the PM_GATE IPC to the FW. + */ + if (target_state->substate == SOF_HDA_DSP_PM_D0I3 && + sdev->system_suspend_target == SOF_SUSPEND_S0IX) + return hda_dsp_set_power_state(sdev, target_state); + + /* + * For all other cases, return without doing anything if + * the DSP is already in the target state. + */ + if (target_state->state == sdev->dsp_power_state.state && + target_state->substate == sdev->dsp_power_state.substate) + return 0; + + return hda_dsp_set_power_state(sdev, target_state); +} + +int hda_dsp_set_power_state_ipc4(struct snd_sof_dev *sdev, + const struct sof_dsp_power_state *target_state) +{ + /* Return without doing anything if the DSP is already in the target state */ + if (target_state->state == sdev->dsp_power_state.state && + target_state->substate == sdev->dsp_power_state.substate) + return 0; + + return hda_dsp_set_power_state(sdev, target_state); +} + /* * Audio DSP states may transform as below:- * diff --git a/sound/soc/sof/intel/hda.h b/sound/soc/sof/intel/hda.h index 0e0cfa81a8f2..c4befacde23e 100644 --- a/sound/soc/sof/intel/hda.h +++ b/sound/soc/sof/intel/hda.h @@ -584,8 +584,10 @@ void hda_dsp_ipc_int_enable(struct snd_sof_dev *sdev); void hda_dsp_ipc_int_disable(struct snd_sof_dev *sdev); bool hda_dsp_core_is_enabled(struct snd_sof_dev *sdev, unsigned int core_mask); -int hda_dsp_set_power_state(struct snd_sof_dev *sdev, - const struct sof_dsp_power_state *target_state); +int hda_dsp_set_power_state_ipc3(struct snd_sof_dev *sdev, + const struct sof_dsp_power_state *target_state); +int hda_dsp_set_power_state_ipc4(struct snd_sof_dev *sdev, + const struct sof_dsp_power_state *target_state); int hda_dsp_suspend(struct snd_sof_dev *sdev, u32 target_state); int hda_dsp_resume(struct snd_sof_dev *sdev); diff --git a/sound/soc/sof/intel/icl.c b/sound/soc/sof/intel/icl.c index 435941a1692f..0f249efc6a5a 100644 --- a/sound/soc/sof/intel/icl.c +++ b/sound/soc/sof/intel/icl.c @@ -116,6 +116,8 @@ int sof_icl_ops_init(struct snd_sof_dev *sdev) /* debug */ sof_icl_ops.ipc_dump = cnl_ipc_dump; + + sof_icl_ops.set_power_state = hda_dsp_set_power_state_ipc3; } if (sdev->pdata->ipc_type == SOF_INTEL_IPC4) { @@ -141,6 +143,8 @@ int sof_icl_ops_init(struct snd_sof_dev *sdev) /* debug */ sof_icl_ops.ipc_dump = cnl_ipc4_dump; + + sof_icl_ops.set_power_state = hda_dsp_set_power_state_ipc4; } /* debug */ diff --git a/sound/soc/sof/intel/mtl.c b/sound/soc/sof/intel/mtl.c index 9f969e07fc27..46caf3ccde66 100644 --- a/sound/soc/sof/intel/mtl.c +++ b/sound/soc/sof/intel/mtl.c @@ -668,6 +668,8 @@ int sof_mtl_ops_init(struct snd_sof_dev *sdev) /* set DAI ops */ hda_set_dai_drv_ops(sdev, &sof_mtl_ops); + sof_mtl_ops.set_power_state = hda_dsp_set_power_state_ipc4; + return 0; }; EXPORT_SYMBOL_NS(sof_mtl_ops_init, SND_SOC_SOF_INTEL_HDA_COMMON); diff --git a/sound/soc/sof/intel/tgl.c b/sound/soc/sof/intel/tgl.c index 58ac3a46e6a7..2713b7dc7931 100644 --- a/sound/soc/sof/intel/tgl.c +++ b/sound/soc/sof/intel/tgl.c @@ -71,6 +71,8 @@ int sof_tgl_ops_init(struct snd_sof_dev *sdev) /* debug */ sof_tgl_ops.ipc_dump = cnl_ipc_dump; + + sof_tgl_ops.set_power_state = hda_dsp_set_power_state_ipc3; } if (sdev->pdata->ipc_type == SOF_INTEL_IPC4) { @@ -96,6 +98,8 @@ int sof_tgl_ops_init(struct snd_sof_dev *sdev) /* debug */ sof_tgl_ops.ipc_dump = cnl_ipc4_dump; + + sof_tgl_ops.set_power_state = hda_dsp_set_power_state_ipc4; } /* set DAI driver ops */ -- 2.40.0

2 1

[PATCH] ASoC: es8316: Don't use ranges based register lookup for a single register
by Mark Brown 21 Apr '23

21 Apr '23

The es8316 driver uses a register range to specify the single volatile register it has. While the cost will be in the noise this is a bunch of overhead compared to just having a volatile_reg() callback so switch to the callback. Signed-off-by: Mark Brown <broonie(a)kernel.org> --- sound/soc/codecs/es8316.c | 19 ++++++++++--------- 1 file changed, 10 insertions(+), 9 deletions(-) diff --git a/sound/soc/codecs/es8316.c b/sound/soc/codecs/es8316.c index 056c3082fe02..1736a905abdb 100644 --- a/sound/soc/codecs/es8316.c +++ b/sound/soc/codecs/es8316.c @@ -803,14 +803,15 @@ static const struct snd_soc_component_driver soc_component_dev_es8316 = { .endianness = 1, }; -static const struct regmap_range es8316_volatile_ranges[] = { - regmap_reg_range(ES8316_GPIO_FLAG, ES8316_GPIO_FLAG), -}; - -static const struct regmap_access_table es8316_volatile_table = { - .yes_ranges = es8316_volatile_ranges, - .n_yes_ranges = ARRAY_SIZE(es8316_volatile_ranges), -}; +static bool es8316_volatile_reg(struct device *dev, unsigned int reg) +{ + switch (reg) { + case ES8316_GPIO_FLAG: + return true; + default: + return false; + } +} static const struct regmap_config es8316_regmap = { .reg_bits = 8, @@ -818,7 +819,7 @@ static const struct regmap_config es8316_regmap = { .use_single_read = true, .use_single_write = true, .max_register = 0x53, - .volatile_table = &es8316_volatile_table, + .volatile_reg = es8316_volatile_reg, .cache_type = REGCACHE_RBTREE, }; --- base-commit: e8d018dd0257f744ca50a729e3d042cf2ec9da65 change-id: 20230419-asoc-es8316-volatile-5083c880627d Best regards, -- Mark Brown <broonie(a)kernel.org>

1 1

[PATCH 0/7] ASoC: Intel: boards: updates for 6.4
by Pierre-Louis Bossart 21 Apr '23

21 Apr '23

Preparation of ALC712 support with different types of SoundWire devices per link, new RaptorLake SoundWire device, better error handling for Cirrus devices and cosmetic changes for Max98373. Bard Liao (3): ASoC: Intel: sof_sdw: set codec_num = 1 if the device is not aggregated ASoC: Intel: sof_sdw: support different devices on the same sdw link ASoC: Intel: sof_sdw: append codec type to dai link name Curtis Malainey (1): ASoC: Intel: sof_cirrus_common: Guard against missing buses Yong Zhi (2): ASoC: Intel: sof_sdw: remove late_probe flag in struct sof_sdw_codec_info ASoC: Intel: sof_sdw_max98373: change sof_sdw_mx8373_late_probe to static call apoorv (1): ASoC: Intel: soc-acpi: Add entry for rt711-sdca-sdw at link 2 in RPL match table sound/soc/intel/boards/sof_cirrus_common.c | 7 +- sound/soc/intel/boards/sof_sdw.c | 181 ++++++++++++------ sound/soc/intel/boards/sof_sdw_common.h | 3 - sound/soc/intel/boards/sof_sdw_max98373.c | 22 +-- .../intel/common/soc-acpi-intel-rpl-match.c | 17 +- 5 files changed, 152 insertions(+), 78 deletions(-) -- 2.37.2

2 8

[PATCH v2 0/2] ASoC: SOF: add no_reply IPC calls
by Pierre-Louis Bossart 21 Apr '23

21 Apr '23

Simplify IPC messages to avoid passing a reply structure that is not used later. Changes since v1: fixed rebase issue leading to allmodconfig compilation error Curtis Malainey (2): ASoC: SOF: ipc: Add no reply inline calls ASoC: SOF: Use no_reply calls for TX sound/soc/sof/compress.c | 8 ++---- sound/soc/sof/intel/hda-loader.c | 2 +- sound/soc/sof/ipc3-dtrace.c | 12 +++------ sound/soc/sof/ipc3-pcm.c | 6 ++--- sound/soc/sof/ipc3-topology.c | 33 +++++++---------------- sound/soc/sof/ipc3.c | 12 +++------ sound/soc/sof/ipc4-pcm.c | 6 ++--- sound/soc/sof/ipc4-topology.c | 10 +++---- sound/soc/sof/sof-client-ipc-flood-test.c | 3 +-- sound/soc/sof/sof-client-probes-ipc3.c | 12 +++------ sound/soc/sof/sof-client-probes-ipc4.c | 4 +-- sound/soc/sof/sof-client.h | 4 +++ sound/soc/sof/sof-priv.h | 10 +++++++ 13 files changed, 51 insertions(+), 71 deletions(-) -- 2.37.2

2 3

[PATCH 0/2] ASoC: SOF: add no_reply IPC calls
by Pierre-Louis Bossart 21 Apr '23

21 Apr '23

Simplify IPC messages to avoid passing a reply structure that is not used later. Curtis Malainey (2): ASoC: SOF: ipc: Add no reply inline calls ASoC: SOF: Use no_reply calls for TX sound/soc/sof/compress.c | 12 +++------ sound/soc/sof/intel/hda-loader.c | 2 +- sound/soc/sof/ipc3-dtrace.c | 12 +++------ sound/soc/sof/ipc3-pcm.c | 6 ++--- sound/soc/sof/ipc3-topology.c | 33 +++++++---------------- sound/soc/sof/ipc3.c | 12 +++------ sound/soc/sof/ipc4-pcm.c | 6 ++--- sound/soc/sof/ipc4-topology.c | 10 +++---- sound/soc/sof/sof-client-ipc-flood-test.c | 3 +-- sound/soc/sof/sof-client-probes-ipc3.c | 12 +++------ sound/soc/sof/sof-client-probes-ipc4.c | 4 +-- sound/soc/sof/sof-client.h | 4 +++ sound/soc/sof/sof-priv.h | 10 +++++++ 13 files changed, 52 insertions(+), 74 deletions(-) -- 2.37.2

3 7

[PATCH] usb-audio: Rate limit usb_set_interface error reporting
by Chris Down 21 Apr '23

21 Apr '23

When an error occurs during USB disconnection sometimes things can go wrong as endpoint_set_interface may end up being called repeatedly. For example: % dmesg --notime | grep 'usb 3-7.1.4' | sort | uniq -c | head -2 3069 usb 3-7.1.4: 1:1: usb_set_interface failed (-19) 908 usb 3-7.1.4: 1:1: usb_set_interface failed (-71) In my case, there sometimes are hundreds of these usb_set_interface failure messages a second when I disconnect the hub that has my USB audio device. These messages can take a huge amount of the kmsg ringbuffer and don't provide any extra information over the previous ones, so ratelimit them. Signed-off-by: Chris Down <chris(a)chrisdown.name> --- sound/usb/endpoint.c | 5 +++-- sound/usb/usbaudio.h | 2 ++ 2 files changed, 5 insertions(+), 2 deletions(-) diff --git a/sound/usb/endpoint.c b/sound/usb/endpoint.c index 647fa054d8b1..2cd99cc8c360 100644 --- a/sound/usb/endpoint.c +++ b/sound/usb/endpoint.c @@ -916,8 +916,9 @@ static int endpoint_set_interface(struct snd_usb_audio *chip, ep->iface, altset, ep->ep_num); err = usb_set_interface(chip->dev, ep->iface, altset); if (err < 0) { - usb_audio_err(chip, "%d:%d: usb_set_interface failed (%d)\n", - ep->iface, altset, err); + usb_audio_err_ratelimited( + chip, "%d:%d: usb_set_interface failed (%d)\n", + ep->iface, altset, err); return err; } diff --git a/sound/usb/usbaudio.h b/sound/usb/usbaudio.h index f5a8dca66457..38a85b2c9a73 100644 --- a/sound/usb/usbaudio.h +++ b/sound/usb/usbaudio.h @@ -67,6 +67,8 @@ struct snd_usb_audio { #define usb_audio_err(chip, fmt, args...) \ dev_err(&(chip)->dev->dev, fmt, ##args) +#define usb_audio_err_ratelimited(chip, fmt, args...) \ + dev_err_ratelimited(&(chip)->dev->dev, fmt, ##args) #define usb_audio_warn(chip, fmt, args...) \ dev_warn(&(chip)->dev->dev, fmt, ##args) #define usb_audio_info(chip, fmt, args...) \ -- 2.40.0

2 5

[PATCH] ALSA: emu10k1: properly assert DSP init constraints
by Oswald Buddenhagen 21 Apr '23

21 Apr '23

If these are hit, we've already trashed kernel space. There is no recovery from that. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- sound/pci/emu10k1/emufx.c | 21 +++++---------------- 1 file changed, 5 insertions(+), 16 deletions(-) diff --git a/sound/pci/emu10k1/emufx.c b/sound/pci/emu10k1/emufx.c index 6cf7c8b1de47..f6f05219f7fc 100644 --- a/sound/pci/emu10k1/emufx.c +++ b/sound/pci/emu10k1/emufx.c @@ -1773,22 +1773,19 @@ A_OP(icode, &ptr, iMAC0, A_GPR(var), A_GPR(var), A_GPR(vol), A_EXTIN(input)) * ok, set up done.. */ - if (gpr > tmp) { - snd_BUG(); - err = -EIO; - goto __err; - } + BUG_ON(gpr > tmp); + BUG_ON(nctl > SND_EMU10K1_GPR_CONTROLS); + /* clear remaining instruction memory */ while (ptr < 0x400) A_OP(icode, &ptr, 0x0f, 0xc0, 0xc0, 0xcf, 0xc0); icode->gpr_add_control_count = nctl; icode->gpr_add_controls = controls; emu->support_tlv = 1; /* support TLV */ err = snd_emu10k1_icode_poke(emu, icode, true); emu->support_tlv = 0; /* clear again */ -__err: kfree(controls); __err_ctrls: kfree(icode->gpr_map); @@ -2391,16 +2388,8 @@ static int _snd_emu10k1_init_efx(struct snd_emu10k1 *emu) } - if (gpr > tmp) { - snd_BUG(); - err = -EIO; - goto __err; - } - if (i > SND_EMU10K1_GPR_CONTROLS) { - snd_BUG(); - err = -EIO; - goto __err; - } + BUG_ON(gpr > tmp); + BUG_ON(i > SND_EMU10K1_GPR_CONTROLS); /* clear remaining instruction memory */ while (ptr < 0x200) -- 2.40.0.152.g15d061e6df

2 3

[PATCH] ALSA: emu10k1: clarify various fx8010.*_mask fields
by Oswald Buddenhagen 21 Apr '23

21 Apr '23

extin_mask and extout_mask are used only by the SbLive! microcode, so they have no effect on Audigy. Eliminate fxbus_mask entirely, as it wasn't actually used for anything. As a drive-by, remove the pointless pad1 field from struct snd_emu10k1_fx8010 - it is not visible to user space, so it has no binary compatibility constraints. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- include/sound/emu10k1.h | 6 ++---- sound/pci/emu10k1/emu10k1_main.c | 7 ++++--- sound/pci/emu10k1/emufx.c | 9 ++++----- 3 files changed, 10 insertions(+), 12 deletions(-) diff --git a/include/sound/emu10k1.h b/include/sound/emu10k1.h index 39787fecc8d9..3407ca4a1210 100644 --- a/include/sound/emu10k1.h +++ b/include/sound/emu10k1.h @@ -1599,10 +1599,8 @@ struct snd_emu10k1_fx8010_pcm { }; struct snd_emu10k1_fx8010 { - unsigned short fxbus_mask; /* used FX buses (bitmask) */ - unsigned short extin_mask; /* used external inputs (bitmask) */ - unsigned short extout_mask; /* used external outputs (bitmask) */ - unsigned short pad1; + unsigned short extin_mask; /* used external inputs (bitmask); not used for Audigy */ + unsigned short extout_mask; /* used external outputs (bitmask); not used for Audigy */ unsigned int itram_size; /* internal TRAM size in samples */ struct snd_dma_buffer etram_pages; /* external TRAM pages and size */ unsigned int dbg; /* FX debugger register */ diff --git a/sound/pci/emu10k1/emu10k1_main.c b/sound/pci/emu10k1/emu10k1_main.c index 3880f359e688..65fd6b62bc9c 100644 --- a/sound/pci/emu10k1/emu10k1_main.c +++ b/sound/pci/emu10k1/emu10k1_main.c @@ -1901,11 +1901,12 @@ int snd_emu10k1_create(struct snd_card *card, pci_set_master(pci); - emu->fx8010.fxbus_mask = 0x303f; + // The masks are not used for Audigy. + // FIXME: these should come from the card_capabilites table. if (extin_mask == 0) - extin_mask = 0x3fcf; + extin_mask = 0x3fcf; // EXTIN_* if (extout_mask == 0) - extout_mask = 0x7fff; + extout_mask = 0x7fff; // EXTOUT_* emu->fx8010.extin_mask = extin_mask; emu->fx8010.extout_mask = extout_mask; emu->enable_ir = enable_ir; diff --git a/sound/pci/emu10k1/emufx.c b/sound/pci/emu10k1/emufx.c index 6cf7c8b1de47..c74e66e03ae0 100644 --- a/sound/pci/emu10k1/emufx.c +++ b/sound/pci/emu10k1/emufx.c @@ -2523,19 +2523,18 @@ static void snd_emu10k1_fx8010_info(struct snd_emu10k1 *emu, struct snd_emu10k1_fx8010_info *info) { const char * const *fxbus, * const *extin, * const *extout; - unsigned short fxbus_mask, extin_mask, extout_mask; + unsigned short extin_mask, extout_mask; int res; info->internal_tram_size = emu->fx8010.itram_size; info->external_tram_size = emu->fx8010.etram_pages.bytes / 2; fxbus = fxbuses; extin = emu->audigy ? audigy_ins : creative_ins; extout = emu->audigy ? audigy_outs : creative_outs; - fxbus_mask = emu->fx8010.fxbus_mask; - extin_mask = emu->fx8010.extin_mask; - extout_mask = emu->fx8010.extout_mask; + extin_mask = emu->audigy ? ~0 : emu->fx8010.extin_mask; + extout_mask = emu->audigy ? ~0 : emu->fx8010.extout_mask; for (res = 0; res < 16; res++, fxbus++, extin++, extout++) { - copy_string(info->fxbus_names[res], fxbus_mask & (1 << res) ? *fxbus : NULL, "FXBUS", res); + copy_string(info->fxbus_names[res], *fxbus, "FXBUS", res); copy_string(info->extin_names[res], extin_mask & (1 << res) ? *extin : NULL, "Unused", res); copy_string(info->extout_names[res], extout_mask & (1 << res) ? *extout : NULL, "Unused", res); } -- 2.40.0.152.g15d061e6df

2 1

[PATCH v3] docs: sound/kernel-api/writing-an-alsa-driver.rst: polishing
by Oswald Buddenhagen 21 Apr '23

21 Apr '23

- Update some outdated info - Language fixes - Whitespace/formatting fixes - Prefer attached over stand-alone '::' Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen(a)gmx.de> --- v3: - fixed one fixme and dropped another one (these were actually meant to go into the RFC patch ...) v2: - dropped questionable hunk from period timer example code - new hunk: improved wording wrt period sizes --- .../kernel-api/writing-an-alsa-driver.rst | 1051 +++++++---------- 1 file changed, 398 insertions(+), 653 deletions(-) diff --git a/Documentation/sound/kernel-api/writing-an-alsa-driver.rst b/Documentation/sound/kernel-api/writing-an-alsa-driver.rst index a368529e8ed3..93fae4dad19c 100644 --- a/Documentation/sound/kernel-api/writing-an-alsa-driver.rst +++ b/Documentation/sound/kernel-api/writing-an-alsa-driver.rst @@ -19,18 +19,13 @@ explain the general topic of linux kernel coding and doesn't cover low-level driver implementation details. It only describes the standard way to write a PCI sound driver on ALSA. -This document is still a draft version. Any feedback and corrections, -please!! - File Tree Structure =================== General ------- -The file tree structure of ALSA driver is depicted below. - -:: +The file tree structure of ALSA driver is depicted below:: sound /core @@ -68,39 +63,39 @@ kernel config. core/oss ~~~~~~~~ -The codes for PCM and mixer OSS emulation modules are stored in this -directory. The rawmidi OSS emulation is included in the ALSA rawmidi +The code for OSS PCM and mixer emulation modules is stored in this +directory. The OSS rawmidi emulation is included in the ALSA rawmidi code since it's quite small. The sequencer code is stored in ``core/seq/oss`` directory (see `below <core/seq/oss_>`__). core/seq ~~~~~~~~ This directory and its sub-directories are for the ALSA sequencer. This directory contains the sequencer core and primary sequencer modules such -like snd-seq-midi, snd-seq-virmidi, etc. They are compiled only when +as snd-seq-midi, snd-seq-virmidi, etc. They are compiled only when ``CONFIG_SND_SEQUENCER`` is set in the kernel config. core/seq/oss ~~~~~~~~~~~~ -This contains the OSS sequencer emulation codes. +This contains the OSS sequencer emulation code. include directory ----------------- This is the place for the public header files of ALSA drivers, which are -to be exported to user-space, or included by several files at different +to be exported to user-space, or included by several files in different directories. Basically, the private header files should not be placed in this directory, but you may still find files there, due to historical reasons :) drivers directory ----------------- This directory contains code shared among different drivers on different architectures. They are hence supposed not to be architecture-specific. -For example, the dummy pcm driver and the serial MIDI driver are found +For example, the dummy PCM driver and the serial MIDI driver are found in this directory. In the sub-directories, there is code for components which are independent from bus and cpu architectures. @@ -156,8 +151,8 @@ these architectures. usb directory ------------- -This directory contains the USB-audio driver. In the latest version, the -USB MIDI driver is integrated in the usb-audio driver. +This directory contains the USB-audio driver. +The USB MIDI driver is integrated in the usb-audio driver. pcmcia directory ---------------- @@ -175,9 +170,9 @@ layer including ASoC core, codec and machine drivers. oss directory ------------- -Here contains OSS/Lite codes. -All codes have been deprecated except for dmasound on m68k as of -writing this. +This contains OSS/Lite code. +At the time of writing, all code has been removed except for dmasound +on m68k. Basic Flow for PCI Drivers @@ -341,7 +336,7 @@ to details explained in the following section. error: snd_card_free(card); - return err; + return err; } /* destructor -- see the "Destructor" sub-section */ @@ -381,7 +376,7 @@ where ``enable[dev]`` is the module option. Each time the ``probe`` callback is called, check the availability of the device. If not available, simply increment the device index and -returns. dev will be incremented also later (`step 7 +return. dev will be incremented also later (`step 7 <7) Set the PCI driver data and return zero._>`__). 2) Create a card instance @@ -402,9 +397,7 @@ Components`_. 3) Create a main component ~~~~~~~~~~~~~~~~~~~~~~~~~~ -In this part, the PCI resources are allocated. - -:: +In this part, the PCI resources are allocated:: struct mychip *chip; .... @@ -417,13 +410,11 @@ Management`_. When something goes wrong, the probe function needs to deal with the error. In this example, we have a single error handling path placed -at the end of the function. - -:: +at the end of the function:: error: snd_card_free(card); - return err; + return err; Since each component can be properly freed, the single :c:func:`snd_card_free()` call should suffice in most cases. @@ -483,13 +474,11 @@ remove callback and power-management callbacks, too. Destructor ---------- -The destructor, remove callback, simply releases the card instance. Then -the ALSA middle layer will release all the attached components +The destructor, the remove callback, simply releases the card instance. +Then the ALSA middle layer will release all the attached components automatically. -It would be typically just calling :c:func:`snd_card_free()`: - -:: +It would be typically just calling :c:func:`snd_card_free()`:: static void snd_mychip_remove(struct pci_dev *pci) { @@ -504,9 +493,7 @@ Header Files ------------ For the above example, at least the following include files are -necessary. - -:: +necessary:: #include <linux/init.h> #include <linux/pci.h> @@ -544,9 +531,7 @@ list on the card record is used to manage the correct release of resources at destruction. As mentioned above, to create a card instance, call -:c:func:`snd_card_new()`. - -:: +:c:func:`snd_card_new()`:: struct snd_card *card; int err; @@ -572,10 +557,8 @@ struct snd_device object. A component can be a PCM instance, a control interface, a raw MIDI interface, etc. Each such instance has one component entry. -A component can be created via :c:func:`snd_device_new()` -function. - -:: +A component can be created via the :c:func:`snd_device_new()` +function:: snd_device_new(card, SNDRV_DEV_XXX, chip, &ops); @@ -591,7 +574,7 @@ allocated manually beforehand, and its pointer is passed as the argument. This pointer (``chip`` in the above example) is used as the identifier for the instance. -Each pre-defined ALSA component such as ac97 and pcm calls +Each pre-defined ALSA component such as AC97 and PCM calls :c:func:`snd_device_new()` inside its constructor. The destructor for each component is defined in the callback pointers. Hence, you don't need to take care of calling a destructor for such a component. @@ -605,9 +588,7 @@ Chip-Specific Data ------------------ Chip-specific information, e.g. the I/O port address, its resource -pointer, or the irq number, is stored in the chip-specific record. - -:: +pointer, or the irq number, is stored in the chip-specific record:: struct mychip { .... @@ -620,9 +601,7 @@ In general, there are two ways of allocating the chip record. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ As mentioned above, you can pass the extra-data-length to the 5th -argument of :c:func:`snd_card_new()`, i.e. - -:: +argument of :c:func:`snd_card_new()`, e.g.:: err = snd_card_new(&pci->dev, index[dev], id[dev], THIS_MODULE, sizeof(struct mychip), &card); @@ -642,9 +621,7 @@ released together with the card instance. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ After allocating a card instance via :c:func:`snd_card_new()` -(with ``0`` on the 4th arg), call :c:func:`kzalloc()`. - -:: +(with ``0`` on the 4th arg), call :c:func:`kzalloc()`:: struct snd_card *card; struct mychip *chip; @@ -663,39 +640,33 @@ The chip record should have the field to hold the card pointer at least, }; -Then, set the card pointer in the returned chip instance. - -:: +Then, set the card pointer in the returned chip instance:: chip->card = card; Next, initialize the fields, and register this chip record as a -low-level device with a specified ``ops``, - -:: +low-level device with a specified ``ops``:: static const struct snd_device_ops ops = { .dev_free = snd_mychip_dev_free, }; .... snd_device_new(card, SNDRV_DEV_LOWLEVEL, chip, &ops); :c:func:`snd_mychip_dev_free()` is the device-destructor -function, which will call the real destructor. - -:: +function, which will call the real destructor:: static int snd_mychip_dev_free(struct snd_device *device) { return snd_mychip_free(device->device_data); } where :c:func:`snd_mychip_free()` is the real destructor. -The demerit of this method is the obviously more amount of codes. -The merit is, however, you can trigger the own callback at registering -and disconnecting the card via setting in snd_device_ops. -About the registering and disconnecting the card, see the subsections +The demerit of this method is the obviously larger amount of code. +The merit is, however, that you can trigger your own callback at +registering and disconnecting the card via a setting in snd_device_ops. +About registering and disconnecting the card, see the subsections below. @@ -724,9 +695,7 @@ Full Code Example ----------------- In this section, we'll complete the chip-specific constructor, -destructor and PCI entries. Example code is shown first, below. - -:: +destructor and PCI entries. Example code is shown first, below:: struct mychip { struct snd_card *card; @@ -866,9 +835,7 @@ resources. Also, you need to set the proper PCI DMA mask to limit the accessed I/O range. In some cases, you might need to call :c:func:`pci_set_master()` function, too. -Suppose the 28bit mask, and the code to be added would be like: - -:: +Suppose a 28bit mask, the code to be added would look like:: err = pci_enable_device(pci); if (err < 0) @@ -890,9 +857,7 @@ function (see below). Now assume that the PCI device has an I/O port with 8 bytes and an interrupt. Then struct mychip will have the -following fields: - -:: +following fields:: struct mychip { struct snd_card *card; @@ -905,14 +870,12 @@ following fields: For an I/O port (and also a memory region), you need to have the resource pointer for the standard resource management. For an irq, you have to keep only the irq number (integer). But you need to initialize -this number as -1 before actual allocation, since irq 0 is valid. The +this number to -1 before actual allocation, since irq 0 is valid. The port address and its resource pointer can be initialized as null by :c:func:`kzalloc()` automatically, so you don't have to take care of resetting them. -The allocation of an I/O port is done like this: - -:: +The allocation of an I/O port is done like this:: err = pci_request_regions(pci, "My Chip"); if (err < 0) { @@ -928,9 +891,7 @@ The returned value, ``chip->res_port``, is allocated via must be released via :c:func:`kfree()`, but there is a problem with this. This issue will be explained later. -The allocation of an interrupt source is done like this: - -:: +The allocation of an interrupt source is done like this:: if (request_irq(pci->irq, snd_mychip_interrupt, IRQF_SHARED, KBUILD_MODNAME, chip)) { @@ -954,36 +915,31 @@ used for that, but you can use what you like, too. I won't give details about the interrupt handler at this point, but at least its appearance can be explained now. The interrupt handler looks -usually like the following: - -:: +usually as follows:: static irqreturn_t snd_mychip_interrupt(int irq, void *dev_id) { struct mychip *chip = dev_id; .... return IRQ_HANDLED; } After requesting the IRQ, you can passed it to ``card->sync_irq`` -field: -:: +field:: card->irq = chip->irq; -This allows PCM core automatically performing -:c:func:`synchronize_irq()` at the necessary timing like ``hw_free``. +This allows the PCM core to automatically call +:c:func:`synchronize_irq()` at the right time, like before ``hw_free``. See the later section `sync_stop callback`_ for details. Now let's write the corresponding destructor for the resources above. The role of destructor is simple: disable the hardware (if already activated) and release the resources. So far, we have no hardware part, so the disabling code is not written here. To release the resources, the “check-and-release” method is a safer way. -For the interrupt, do like this: - -:: +For the interrupt, do like this:: if (chip->irq >= 0) free_irq(chip->irq, chip); @@ -997,72 +953,59 @@ When you requested I/O ports or memory regions via :c:func:`pci_request_regions()` like in this example, release the resource(s) using the corresponding function, :c:func:`pci_release_region()` or -:c:func:`pci_release_regions()`. - -:: +:c:func:`pci_release_regions()`:: pci_release_regions(chip->pci); When you requested manually via :c:func:`request_region()` or :c:func:`request_mem_region()`, you can release it via :c:func:`release_resource()`. Suppose that you keep the resource pointer returned from :c:func:`request_region()` in -chip->res_port, the release procedure looks like: - -:: +chip->res_port, the release procedure looks like:: release_and_free_resource(chip->res_port); Don't forget to call :c:func:`pci_disable_device()` before the end. -And finally, release the chip-specific record. - -:: +And finally, release the chip-specific record:: kfree(chip); -We didn't implement the hardware disabling part in the above. If you +We didn't implement the hardware disabling part above. If you need to do this, please note that the destructor may be called even before the initialization of the chip is completed. It would be better to have a flag to skip hardware disabling if the hardware was not initialized yet. When the chip-data is assigned to the card using -:c:func:`snd_device_new()` with ``SNDRV_DEV_LOWLELVEL`` , its -destructor is called at the last. That is, it is assured that all other +:c:func:`snd_device_new()` with ``SNDRV_DEV_LOWLELVEL``, its +destructor is called last. That is, it is assured that all other components like PCMs and controls have already been released. You don't have to stop PCMs, etc. explicitly, but just call low-level hardware stopping. The management of a memory-mapped region is almost as same as the -management of an I/O port. You'll need three fields like the -following: - -:: +management of an I/O port. You'll need two fields as follows:: struct mychip { .... unsigned long iobase_phys; void __iomem *iobase_virt; }; -and the allocation would be like below: - -:: +and the allocation would look like below:: err = pci_request_regions(pci, "My Chip"); if (err < 0) { kfree(chip); return err; } chip->iobase_phys = pci_resource_start(pci, 0); chip->iobase_virt = ioremap(chip->iobase_phys, pci_resource_len(pci, 0)); -and the corresponding destructor would be: - -:: +and the corresponding destructor would be:: static int snd_mychip_free(struct mychip *chip) { @@ -1075,9 +1018,7 @@ and the corresponding destructor would be: } Of course, a modern way with :c:func:`pci_iomap()` will make things a -bit easier, too. - -:: +bit easier, too:: err = pci_request_regions(pci, "My Chip"); if (err < 0) { @@ -1097,9 +1038,7 @@ struct pci_device_id table for this chipset. It's a table of PCI vendor/device ID number, and some masks. -For example, - -:: +For example:: static struct pci_device_id snd_mychip_ids[] = { { PCI_VENDOR_ID_FOO, PCI_DEVICE_ID_BAR, @@ -1120,24 +1059,20 @@ The last entry of this list is the terminator. You must specify this all-zero entry. Then, prepare the struct pci_driver -record: - -:: +record:: static struct pci_driver driver = { .name = KBUILD_MODNAME, .id_table = snd_mychip_ids, .probe = snd_mychip_probe, .remove = snd_mychip_remove, }; The ``probe`` and ``remove`` functions have already been defined in the previous sections. The ``name`` field is the name string of this -device. Note that you must not use a slash “/” in this string. +device. Note that you must not use slashes (“/”) in this string. -And at last, the module entries: - -:: +And at last, the module entries:: static int __init alsa_card_mychip_init(void) { @@ -1167,33 +1102,31 @@ The PCM middle layer of ALSA is quite powerful and it is only necessary for each driver to implement the low-level functions to access its hardware. -For accessing to the PCM layer, you need to include ``<sound/pcm.h>`` +To access the PCM layer, you need to include ``<sound/pcm.h>`` first. In addition, ``<sound/pcm_params.h>`` might be needed if you -access to some functions related with hw_param. +access some functions related with hw_param. -Each card device can have up to four pcm instances. A pcm instance -corresponds to a pcm device file. The limitation of number of instances -comes only from the available bit size of the Linux's device numbers. -Once when 64bit device number is used, we'll have more pcm instances +Each card device can have up to four PCM instances. A PCM instance +corresponds to a PCM device file. The limitation of number of instances +comes only from the available bit size of Linux' device numbers. +Once 64bit device numbers are used, we'll have more PCM instances available. -A pcm instance consists of pcm playback and capture streams, and each -pcm stream consists of one or more pcm substreams. Some soundcards +A PCM instance consists of PCM playback and capture streams, and each +PCM stream consists of one or more PCM substreams. Some soundcards support multiple playback functions. For example, emu10k1 has a PCM playback of 32 stereo substreams. In this case, at each open, a free substream is (usually) automatically chosen and opened. Meanwhile, when -only one substream exists and it was already opened, the successful open +only one substream exists and it was already opened, a subsequent open will either block or error with ``EAGAIN`` according to the file open mode. But you don't have to care about such details in your driver. The PCM middle layer will take care of such work. Full Code Example ----------------- The example code below does not include any hardware access routines but -shows only the skeleton, how to build up the PCM interfaces. - -:: +shows only the skeleton, how to build up the PCM interfaces:: #include <sound/pcm.h> .... @@ -1399,10 +1332,8 @@ shows only the skeleton, how to build up the PCM interfaces. PCM Constructor --------------- -A pcm instance is allocated by the :c:func:`snd_pcm_new()` -function. It would be better to create a constructor for pcm, namely, - -:: +A PCM instance is allocated by the :c:func:`snd_pcm_new()` +function. It would be better to create a constructor for the PCM, namely:: static int snd_mychip_new_pcm(struct mychip *chip) { @@ -1415,16 +1346,16 @@ function. It would be better to create a constructor for pcm, namely, pcm->private_data = chip; strcpy(pcm->name, "My Chip"); chip->pcm = pcm; - .... + ... return 0; } -The :c:func:`snd_pcm_new()` function takes four arguments. The -first argument is the card pointer to which this pcm is assigned, and +The :c:func:`snd_pcm_new()` function takes six arguments. The +first argument is the card pointer to which this PCM is assigned, and the second is the ID string. The third argument (``index``, 0 in the above) is the index of this new -pcm. It begins from zero. If you create more than one pcm instances, +PCM. It begins from zero. If you create more than one PCM instances, specify the different numbers in this argument. For example, ``index = 1`` for the second PCM device. @@ -1437,26 +1368,20 @@ If a chip supports multiple playbacks or captures, you can specify more numbers, but they must be handled properly in open/close, etc. callbacks. When you need to know which substream you are referring to, then it can be obtained from struct snd_pcm_substream data passed to each -callback as follows: - -:: +callback as follows:: struct snd_pcm_substream *substream; int index = substream->number; -After the pcm is created, you need to set operators for each pcm stream. - -:: +After the PCM is created, you need to set operators for each PCM stream:: snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_PLAYBACK, &snd_mychip_playback_ops); snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_CAPTURE, &snd_mychip_capture_ops); -The operators are defined typically like this: - -:: +The operators are defined typically like this:: static struct snd_pcm_ops snd_mychip_playback_ops = { .open = snd_mychip_pcm_open, @@ -1472,41 +1397,35 @@ All the callbacks are described in the Operators_ subsection. After setting the operators, you probably will want to pre-allocate the buffer and set up the managed allocation mode. -For that, simply call the following: - -:: +For that, simply call the following:: snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_DEV, &chip->pci->dev, 64*1024, 64*1024); -It will allocate a buffer up to 64kB as default. Buffer management +It will allocate a buffer up to 64kB by default. Buffer management details will be described in the later section `Buffer and Memory Management`_. -Additionally, you can set some extra information for this pcm in +Additionally, you can set some extra information for this PCM in ``pcm->info_flags``. The available values are defined as ``SNDRV_PCM_INFO_XXX`` in ``<sound/asound.h>``, which is used for the hardware definition (described later). When your soundchip supports only -half-duplex, specify like this: - -:: +half-duplex, specify it like this:: pcm->info_flags = SNDRV_PCM_INFO_HALF_DUPLEX; ... And the Destructor? ----------------------- -The destructor for a pcm instance is not always necessary. Since the pcm +The destructor for a PCM instance is not always necessary. Since the PCM device will be released by the middle layer code automatically, you don't have to call the destructor explicitly. The destructor would be necessary if you created special records internally and needed to release them. In such a case, set the -destructor function to ``pcm->private_free``: - -:: +destructor function to ``pcm->private_free``:: static void mychip_pcm_free(struct snd_pcm *pcm) { @@ -1537,13 +1456,11 @@ Runtime Pointer - The Chest of PCM Information When the PCM substream is opened, a PCM runtime instance is allocated and assigned to the substream. This pointer is accessible via ``substream->runtime``. This runtime pointer holds most information you -need to control the PCM: the copy of hw_params and sw_params +need to control the PCM: a copy of hw_params and sw_params configurations, the buffer pointers, mmap records, spinlocks, etc. The definition of runtime instance is found in ``<sound/pcm.h>``. Here -are the contents of this file: - -:: +is the relevant part of this file:: struct _snd_pcm_runtime { /* -- Status -- */ @@ -1638,24 +1555,20 @@ Hardware Description The hardware descriptor (struct snd_pcm_hardware) contains the definitions of the fundamental hardware configuration. Above all, you'll need to define this -in the `PCM open callback`_. Note that the runtime instance holds the copy of -the descriptor, not the pointer to the existing descriptor. That is, +in the `PCM open callback`_. Note that the runtime instance holds a copy of +the descriptor, not a pointer to the existing descriptor. That is, in the open callback, you can modify the copied descriptor (``runtime->hw``) as you need. For example, if the maximum number of channels is 1 only on some chip models, you can still use the same -hardware descriptor and change the channels_max later: - -:: +hardware descriptor and change the channels_max later:: struct snd_pcm_runtime *runtime = substream->runtime; ... runtime->hw = snd_mychip_playback_hw; /* common definition */ if (chip->model == VERY_OLD_ONE) runtime->hw.channels_max = 1; -Typically, you'll have a hardware descriptor as below: - -:: +Typically, you'll have a hardware descriptor as below:: static struct snd_pcm_hardware snd_mychip_playback_hw = { .info = (SNDRV_PCM_INFO_MMAP | @@ -1676,71 +1589,72 @@ Typically, you'll have a hardware descriptor as below: }; - The ``info`` field contains the type and capabilities of this - pcm. The bit flags are defined in ``<sound/asound.h>`` as + PCM. The bit flags are defined in ``<sound/asound.h>`` as ``SNDRV_PCM_INFO_XXX``. Here, at least, you have to specify whether - the mmap is supported and which interleaved format is + mmap is supported and which interleaving formats are supported. When the hardware supports mmap, add the ``SNDRV_PCM_INFO_MMAP`` flag here. When the hardware supports the - interleaved or the non-interleaved formats, + interleaved or the non-interleaved formats, the ``SNDRV_PCM_INFO_INTERLEAVED`` or ``SNDRV_PCM_INFO_NONINTERLEAVED`` flag must be set, respectively. If both are supported, you can set both, too. In the above example, ``MMAP_VALID`` and ``BLOCK_TRANSFER`` are specified for the OSS mmap mode. Usually both are set. Of course, - ``MMAP_VALID`` is set only if the mmap is really supported. + ``MMAP_VALID`` is set only if mmap is really supported. The other possible flags are ``SNDRV_PCM_INFO_PAUSE`` and - ``SNDRV_PCM_INFO_RESUME``. The ``PAUSE`` bit means that the pcm + ``SNDRV_PCM_INFO_RESUME``. The ``PAUSE`` bit means that the PCM supports the “pause” operation, while the ``RESUME`` bit means that - the pcm supports the full “suspend/resume” operation. If the + the PCM supports the full “suspend/resume” operation. If the ``PAUSE`` flag is set, the ``trigger`` callback below must handle the corresponding (pause push/release) commands. The suspend/resume trigger commands can be defined even without the ``RESUME`` - flag. See `Power Management`_ section for details. + flag. See the `Power Management`_ section for details. When the PCM substreams can be synchronized (typically, - synchronized start/stop of a playback and a capture streams), you + synchronized start/stop of a playback and a capture stream), you can give ``SNDRV_PCM_INFO_SYNC_START``, too. In this case, you'll need to check the linked-list of PCM substreams in the trigger - callback. This will be described in the later section. + callback. This will be described in a later section. -- ``formats`` field contains the bit-flags of supported formats +- The ``formats`` field contains the bit-flags of supported formats (``SNDRV_PCM_FMTBIT_XXX``). If the hardware supports more than one format, give all or'ed bits. In the example above, the signed 16bit little-endian format is specified. -- ``rates`` field contains the bit-flags of supported rates +- The ``rates`` field contains the bit-flags of supported rates (``SNDRV_PCM_RATE_XXX``). When the chip supports continuous rates, - pass ``CONTINUOUS`` bit additionally. The pre-defined rate bits are - provided only for typical rates. If your chip supports + pass the ``CONTINUOUS`` bit additionally. The pre-defined rate bits + are provided only for typical rates. If your chip supports unconventional rates, you need to add the ``KNOT`` bit and set up the hardware constraint manually (explained later). - ``rate_min`` and ``rate_max`` define the minimum and maximum sample rate. This should correspond somehow to ``rates`` bits. -- ``channels_min`` and ``channels_max`` define, as you might already +- ``channels_min`` and ``channels_max`` define, as you might have already expected, the minimum and maximum number of channels. - ``buffer_bytes_max`` defines the maximum buffer size in bytes. There is no ``buffer_bytes_min`` field, since it can be calculated from the minimum period size and the minimum number of periods. Meanwhile, ``period_bytes_min`` and ``period_bytes_max`` define the minimum and maximum size of the period in bytes. ``periods_max`` and ``periods_min`` define the maximum and minimum number of periods in the buffer. The “period” is a term that corresponds to a fragment in the OSS - world. The period defines the size at which a PCM interrupt is - generated. This size strongly depends on the hardware. Generally, - the smaller period size will give you more interrupts, that is, - more controls. In the case of capture, this size defines the input - latency. On the other hand, the whole buffer size defines the - output latency for the playback direction. + world. The period defines the point at which a PCM interrupt is + generated. This point strongly depends on the hardware. Generally, + a smaller period size will give you more interrupts, which results + in being able to fill/drain the buffer more timely. In the case of + capture, this size defines the input latency. On the other hand, + the whole buffer size defines the output latency for the playback + direction. - There is also a field ``fifo_size``. This specifies the size of the - hardware FIFO, but currently it is neither used in the driver nor + hardware FIFO, but currently it is neither used by the drivers nor in the alsa-lib. So, you can ignore this field. PCM Configurations @@ -1759,63 +1673,60 @@ One thing to be noted is that the configured buffer and period sizes are stored in “frames” in the runtime. In the ALSA world, ``1 frame = channels \* samples-size``. For conversion between frames and bytes, you can use the :c:func:`frames_to_bytes()` and -:c:func:`bytes_to_frames()` helper functions. - -:: +:c:func:`bytes_to_frames()` helper functions:: period_bytes = frames_to_bytes(runtime, runtime->period_size); Also, many software parameters (sw_params) are stored in frames, too. -Please check the type of the field. ``snd_pcm_uframes_t`` is for the -frames as unsigned integer while ``snd_pcm_sframes_t`` is for the +Please check the type of the field. ``snd_pcm_uframes_t`` is for +frames as unsigned integer while ``snd_pcm_sframes_t`` is for frames as signed integer. DMA Buffer Information ~~~~~~~~~~~~~~~~~~~~~~ -The DMA buffer is defined by the following four fields, ``dma_area``, -``dma_addr``, ``dma_bytes`` and ``dma_private``. The ``dma_area`` +The DMA buffer is defined by the following four fields: ``dma_area``, +``dma_addr``, ``dma_bytes`` and ``dma_private``. ``dma_area`` holds the buffer pointer (the logical address). You can call :c:func:`memcpy()` from/to this pointer. Meanwhile, ``dma_addr`` holds the physical address of the buffer. This field is specified only when -the buffer is a linear buffer. ``dma_bytes`` holds the size of buffer -in bytes. ``dma_private`` is used for the ALSA DMA allocator. +the buffer is a linear buffer. ``dma_bytes`` holds the size of the +buffer in bytes. ``dma_private`` is used for the ALSA DMA allocator. If you use either the managed buffer allocation mode or the standard API function :c:func:`snd_pcm_lib_malloc_pages()` for allocating the buffer, these fields are set by the ALSA middle layer, and you should *not* change them by yourself. You can read them but not write them. On the other hand, if you want to allocate the buffer by yourself, you'll -need to manage it in hw_params callback. At least, ``dma_bytes`` is +need to manage it in the hw_params callback. At least, ``dma_bytes`` is mandatory. ``dma_area`` is necessary when the buffer is mmapped. If your driver doesn't support mmap, this field is not necessary. ``dma_addr`` is also optional. You can use dma_private as you like, too. Running Status ~~~~~~~~~~~~~~ The running status can be referred via ``runtime->status``. This is -the pointer to the struct snd_pcm_mmap_status record. +a pointer to a struct snd_pcm_mmap_status record. For example, you can get the current DMA hardware pointer via ``runtime->status->hw_ptr``. The DMA application pointer can be referred via ``runtime->control``, -which points to the struct snd_pcm_mmap_control record. -However, accessing directly to this value is not recommended. +which points to a struct snd_pcm_mmap_control record. +However, accessing this value directly is not recommended. Private Data ~~~~~~~~~~~~ You can allocate a record for the substream and store it in ``runtime->private_data``. Usually, this is done in the `PCM open callback`_. Don't mix this with ``pcm->private_data``. The ``pcm->private_data`` usually points to the chip instance assigned -statically at the creation of PCM, while the ``runtime->private_data`` -points to a dynamic data structure created at the PCM open -callback. - -:: +statically at creation time of the PCM device, while +``runtime->private_data`` +points to a dynamic data structure created in the PCM open +callback:: static int snd_xxx_open(struct snd_pcm_substream *substream) { @@ -1832,20 +1743,18 @@ The allocated object must be released in the `close callback`_. Operators --------- -OK, now let me give details about each pcm callback (``ops``). In +OK, now let me give details about each PCM callback (``ops``). In general, every callback must return 0 if successful, or a negative error number such as ``-EINVAL``. To choose an appropriate error number, it is advised to check what value other parts of the kernel return when the same kind of request fails. -The callback function takes at least the argument with +Each callback function takes at least one argument containing a struct snd_pcm_substream pointer. To retrieve the chip record from the given substream instance, you can use the following -macro. +macro:: -:: - - int xxx() { + int xxx(...) { struct mychip *chip = snd_pcm_substream_chip(substream); .... } @@ -1864,12 +1773,10 @@ PCM open callback static int snd_xxx_open(struct snd_pcm_substream *substream); -This is called when a pcm substream is opened. +This is called when a PCM substream is opened. At least, here you have to initialize the ``runtime->hw`` -record. Typically, this is done by like this: - -:: +record. Typically, this is done like this:: static int snd_xxx_open(struct snd_pcm_substream *substream) { @@ -1883,7 +1790,7 @@ record. Typically, this is done by like this: where ``snd_mychip_playback_hw`` is the pre-defined hardware description. -You can allocate a private data in this callback, as described in +You can allocate private data in this callback, as described in the `Private Data`_ section. If the hardware configuration needs more constraints, set the hardware @@ -1897,73 +1804,69 @@ close callback static int snd_xxx_close(struct snd_pcm_substream *substream); -Obviously, this is called when a pcm substream is closed. +Obviously, this is called when a PCM substream is closed. -Any private instance for a pcm substream allocated in the ``open`` -callback will be released here. - -:: +Any private instance for a PCM substream allocated in the ``open`` +callback will be released here:: static int snd_xxx_close(struct snd_pcm_substream *substream) { .... kfree(substream->runtime->private_data); .... } ioctl callback ~~~~~~~~~~~~~~ -This is used for any special call to pcm ioctls. But usually you can -leave it as NULL, then PCM core calls the generic ioctl callback -function :c:func:`snd_pcm_lib_ioctl()`. If you need to deal with the +This is used for any special call to PCM ioctls. But usually you can +leave it NULL, then the PCM core calls the generic ioctl callback +function :c:func:`snd_pcm_lib_ioctl()`. If you need to deal with a unique setup of channel info or reset procedure, you can pass your own callback function here. hw_params callback ~~~~~~~~~~~~~~~~~~~ :: static int snd_xxx_hw_params(struct snd_pcm_substream *substream, struct snd_pcm_hw_params *hw_params); -This is called when the hardware parameter (``hw_params``) is set up +This is called when the hardware parameters (``hw_params``) are set up by the application, that is, once when the buffer size, the period -size, the format, etc. are defined for the pcm substream. +size, the format, etc. are defined for the PCM substream. Many hardware setups should be done in this callback, including the allocation of buffers. -Parameters to be initialized are retrieved by +Parameters to be initialized are retrieved by the :c:func:`params_xxx()` macros. -When you set up the managed buffer allocation mode for the substream, +When you choose managed buffer allocation mode for the substream, a buffer is already allocated before this callback gets called. Alternatively, you can call a helper function below for -allocating the buffer, too. - -:: +allocating the buffer:: snd_pcm_lib_malloc_pages(substream, params_buffer_bytes(hw_params)); :c:func:`snd_pcm_lib_malloc_pages()` is available only when the DMA buffers have been pre-allocated. See the section `Buffer Types`_ for more details. -Note that this and ``prepare`` callbacks may be called multiple times -per initialization. For example, the OSS emulation may call these +Note that this one and the ``prepare`` callback may be called multiple +times per initialization. For example, the OSS emulation may call these callbacks at each change via its ioctl. Thus, you need to be careful not to allocate the same buffers many times, which will lead to memory leaks! Calling the helper function above many times is OK. It will release the previous buffer automatically when it was already allocated. -Another note is that this callback is non-atomic (schedulable) as +Another note is that this callback is non-atomic (schedulable) by default, i.e. when no ``nonatomic`` flag set. This is important, because the ``trigger`` callback is atomic (non-schedulable). That is, -mutexes or any schedule-related functions are not available in +mutexes or any schedule-related functions are not available in the ``trigger`` callback. Please see the subsection Atomicity_ for details. @@ -1979,33 +1882,31 @@ This is called to release the resources allocated via This function is always called before the close callback is called. Also, the callback may be called multiple times, too. Keep track -whether the resource was already released. +whether each resource was already released. -When you have set up the managed buffer allocation mode for the PCM +When you have chosen managed buffer allocation mode for the PCM substream, the allocated PCM buffer will be automatically released after this callback gets called. Otherwise you'll have to release the buffer manually. Typically, when the buffer was allocated from the pre-allocated pool, you can use the standard API function -:c:func:`snd_pcm_lib_malloc_pages()` like: - -:: +:c:func:`snd_pcm_lib_malloc_pages()` like:: snd_pcm_lib_free_pages(substream); prepare callback ~~~~~~~~~~~~~~~~ :: static int snd_xxx_prepare(struct snd_pcm_substream *substream); -This callback is called when the pcm is “prepared”. You can set the +This callback is called when the PCM is “prepared”. You can set the format type, sample rate, etc. here. The difference from ``hw_params`` is that the ``prepare`` callback will be called each time :c:func:`snd_pcm_prepare()` is called, i.e. when recovering after underruns, etc. -Note that this callback is now non-atomic. You can use +Note that this callback is non-atomic. You can use schedule-related functions safely in this callback. In this and the following callbacks, you can refer to the values via @@ -2026,13 +1927,11 @@ trigger callback static int snd_xxx_trigger(struct snd_pcm_substream *substream, int cmd); -This is called when the pcm is started, stopped or paused. +This is called when the PCM is started, stopped or paused. -Which action is specified in the second argument, -``SNDRV_PCM_TRIGGER_XXX`` in ``<sound/pcm.h>``. At least, the ``START`` -and ``STOP`` commands must be defined in this callback. - -:: +The action is specified in the second argument, ``SNDRV_PCM_TRIGGER_XXX`` +defined in ``<sound/pcm.h>``. At least, the ``START`` +and ``STOP`` commands must be defined in this callback:: switch (cmd) { case SNDRV_PCM_TRIGGER_START: @@ -2045,49 +1944,49 @@ and ``STOP`` commands must be defined in this callback. return -EINVAL; } -When the pcm supports the pause operation (given in the info field of +When the PCM supports the pause operation (given in the info field of the hardware table), the ``PAUSE_PUSH`` and ``PAUSE_RELEASE`` commands -must be handled here, too. The former is the command to pause the pcm, -and the latter to restart the pcm again. +must be handled here, too. The former is the command to pause the PCM, +and the latter to restart the PCM again. -When the pcm supports the suspend/resume operation, regardless of full +When the PCM supports the suspend/resume operation, regardless of full or partial suspend/resume support, the ``SUSPEND`` and ``RESUME`` commands must be handled, too. These commands are issued when the power-management status is changed. Obviously, the ``SUSPEND`` and -``RESUME`` commands suspend and resume the pcm substream, and usually, +``RESUME`` commands suspend and resume the PCM substream, and usually, they are identical to the ``STOP`` and ``START`` commands, respectively. See the `Power Management`_ section for details. -As mentioned, this callback is atomic as default unless ``nonatomic`` +As mentioned, this callback is atomic by default unless the ``nonatomic`` flag set, and you cannot call functions which may sleep. The ``trigger`` callback should be as minimal as possible, just really -triggering the DMA. The other stuff should be initialized +triggering the DMA. The other stuff should be initialized in ``hw_params`` and ``prepare`` callbacks properly beforehand. sync_stop callback ~~~~~~~~~~~~~~~~~~ :: static int snd_xxx_sync_stop(struct snd_pcm_substream *substream); This callback is optional, and NULL can be passed. It's called after -the PCM core stops the stream and changes the stream state +the PCM core stops the stream, before it changes the stream state via ``prepare``, ``hw_params`` or ``hw_free``. Since the IRQ handler might be still pending, we need to wait until the pending task finishes before moving to the next step; otherwise it -might lead to a crash due to resource conflicts or access to the freed +might lead to a crash due to resource conflicts or access to freed resources. A typical behavior is to call a synchronization function like :c:func:`synchronize_irq()` here. -For majority of drivers that need only a call of +For the majority of drivers that need only a call of :c:func:`synchronize_irq()`, there is a simpler setup, too. -While keeping NULL to ``sync_stop`` PCM callback, the driver can set -``card->sync_irq`` field to store the valid interrupt number after -requesting an IRQ, instead. Then PCM core will look call +While keeping the ``sync_stop`` PCM callback NULL, the driver can set +the ``card->sync_irq`` field to the returned interrupt number after +requesting an IRQ, instead. Then PCM core will call :c:func:`synchronize_irq()` with the given IRQ appropriately. -If the IRQ handler is released at the card destructor, you don't need +If the IRQ handler is released by the card destructor, you don't need to clear ``card->sync_irq``, as the card itself is being released. So, usually you'll need to add just a single line for assigning ``card->sync_irq`` in the driver code unless the driver re-acquires @@ -2103,76 +2002,76 @@ pointer callback static snd_pcm_uframes_t snd_xxx_pointer(struct snd_pcm_substream *substream) This callback is called when the PCM middle layer inquires the current -hardware position on the buffer. The position must be returned in +hardware position in the buffer. The position must be returned in frames, ranging from 0 to ``buffer_size - 1``. -This is called usually from the buffer-update routine in the pcm +This is usually called from the buffer-update routine in the PCM middle layer, which is invoked when :c:func:`snd_pcm_period_elapsed()` -is called in the interrupt routine. Then the pcm middle layer updates +is called by the interrupt routine. Then the PCM middle layer updates the position and calculates the available space, and wakes up the sleeping poll threads, etc. -This callback is also atomic as default. +This callback is also atomic by default. copy_user, copy_kernel and fill_silence ops ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ These callbacks are not mandatory, and can be omitted in most cases. These callbacks are used when the hardware buffer cannot be in the -normal memory space. Some chips have their own buffer on the hardware +normal memory space. Some chips have their own buffer in the hardware which is not mappable. In such a case, you have to transfer the data manually from the memory buffer to the hardware buffer. Or, if the buffer is non-contiguous on both physical and virtual memory spaces, these callbacks must be defined, too. If these two callbacks are defined, copy and set-silence operations -are done by them. The detailed will be described in the later section +are done by them. The details will be described in the later section `Buffer and Memory Management`_. ack callback ~~~~~~~~~~~~ This callback is also not mandatory. This callback is called when the ``appl_ptr`` is updated in read or write operations. Some drivers like emu10k1-fx and cs46xx need to track the current ``appl_ptr`` for the internal buffer, and this callback is useful only for such a purpose. The callback function may return 0 or a negative error. When the -return value is ``-EPIPE``, PCM core treats as a buffer XRUN happens, +return value is ``-EPIPE``, PCM core treats that as a buffer XRUN, and changes the state to ``SNDRV_PCM_STATE_XRUN`` automatically. -This callback is atomic as default. +This callback is atomic by default. page callback ~~~~~~~~~~~~~ This callback is optional too. The mmap calls this callback to get the page fault address. -Since the recent changes, you need no special callback any longer for -the standard SG-buffer or vmalloc-buffer. Hence this callback should -be rarely used. +You need no special callback for the standard SG-buffer or vmalloc- +buffer. Hence this callback should be rarely used. -mmap calllback -~~~~~~~~~~~~~~ +mmap callback +~~~~~~~~~~~~~ This is another optional callback for controlling mmap behavior. -Once when defined, PCM core calls this callback when a page is -memory-mapped instead of dealing via the standard helper. +When defined, the PCM core calls this callback when a page is +memory-mapped, instead of using the standard helper. If you need special handling (due to some architecture or device-specific issues), implement everything here as you like. PCM Interrupt Handler --------------------- -The rest of pcm stuff is the PCM interrupt handler. The role of PCM +The remainder of the PCM stuff is the PCM interrupt handler. The role +of the PCM interrupt handler in the sound driver is to update the buffer position and to tell the PCM middle layer when the buffer position goes across -the prescribed period size. To inform this, call the +the specified period boundary. To inform about this, call the :c:func:`snd_pcm_period_elapsed()` function. -There are several types of sound chips to generate the interrupts. +There are several ways sound chips can generate interrupts. Interrupts at the period (fragment) boundary ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ @@ -2188,14 +2087,12 @@ chip record to hold the current running substream pointer, and set the pointer value at ``open`` callback (and reset at ``close`` callback). If you acquire a spinlock in the interrupt handler, and the lock is used -in other pcm callbacks, too, then you have to release the lock before +in other PCM callbacks, too, then you have to release the lock before calling :c:func:`snd_pcm_period_elapsed()`, because -:c:func:`snd_pcm_period_elapsed()` calls other pcm callbacks +:c:func:`snd_pcm_period_elapsed()` calls other PCM callbacks inside. -Typical code would be like: - -:: +Typical code would look like:: static irqreturn_t snd_mychip_interrupt(int irq, void *dev_id) @@ -2233,9 +2130,7 @@ position and accumulate the processed sample length at each interrupt. When the accumulated size exceeds the period size, call :c:func:`snd_pcm_period_elapsed()` and reset the accumulator. -Typical code would be like the following. - -:: +Typical code would look as follows:: static irqreturn_t snd_mychip_interrupt(int irq, void *dev_id) @@ -2280,25 +2175,25 @@ Typical code would be like the following. On calling :c:func:`snd_pcm_period_elapsed()` ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ -In both cases, even if more than one period are elapsed, you don't have +In both cases, even if more than one period has elapsed, you don't have to call :c:func:`snd_pcm_period_elapsed()` many times. Call only -once. And the pcm layer will check the current hardware pointer and +once. And the PCM layer will check the current hardware pointer and update to the latest status. Atomicity --------- One of the most important (and thus difficult to debug) problems in kernel programming are race conditions. In the Linux kernel, they are usually avoided via spin-locks, mutexes or semaphores. In general, if a race condition can happen in an interrupt handler, it has to be managed atomically, and you have to use a spinlock to protect the critical -session. If the critical section is not in interrupt handler code and if +section. If the critical section is not in interrupt handler code and if taking a relatively long time to execute is acceptable, you should use mutexes or semaphores instead. -As already seen, some pcm callbacks are atomic and some are not. For -example, the ``hw_params`` callback is non-atomic, while ``trigger`` +As already seen, some PCM callbacks are atomic and some are not. For +example, the ``hw_params`` callback is non-atomic, while the ``trigger`` callback is atomic. This means, the latter is called already in a spinlock held by the PCM middle layer, the PCM stream lock. Please take this atomicity into account when you choose a locking scheme in @@ -2313,13 +2208,13 @@ callback, please use :c:func:`udelay()` or :c:func:`mdelay()`. All three atomic callbacks (trigger, pointer, and ack) are called with local interrupts disabled. -The recent changes in PCM core code, however, allow all PCM operations -to be non-atomic. This assumes that the all caller sides are in +However, it is possible to request all PCM operations to be non-atomic. +This assumes that all call sites are in non-atomic contexts. For example, the function :c:func:`snd_pcm_period_elapsed()` is called typically from the interrupt handler. But, if you set up the driver to use a threaded interrupt handler, this call can be in non-atomic context, too. In such -a case, you can set ``nonatomic`` filed of struct snd_pcm object +a case, you can set the ``nonatomic`` field of the struct snd_pcm object after creating it. When this flag is set, mutex and rwsem are used internally in the PCM core instead of spin and rwlocks, so that you can call all PCM functions safely in a non-atomic @@ -2335,14 +2230,12 @@ too. Constraints ----------- -If your chip supports unconventional sample rates, or only the limited -samples, you need to set a constraint for the condition. +Due to physical limitations, hardware is not infinitely configurable. +These limitations are expressed by setting constraints. -For example, in order to restrict the sample rates in the some supported +For example, in order to restrict the sample rates to some supported values, use :c:func:`snd_pcm_hw_constraint_list()`. You need to -call this function in the open callback. - -:: +call this function in the open callback:: static unsigned int rates[] = {4000, 10000, 22050, 44100}; @@ -2364,16 +2257,12 @@ call this function in the open callback. .... } - - There are many different constraints. Look at ``sound/pcm.h`` for a complete list. You can even define your own constraint rules. For example, let's suppose my_chip can manage a substream of 1 channel if and only if the format is ``S16_LE``, otherwise it supports any format -specified in struct snd_pcm_hardware> (or in any other -constraint_list). You can build a rule like this: - -:: +specified in struct snd_pcm_hardware (or in any other +constraint_list). You can build a rule like this:: static int hw_rule_channels_by_format(struct snd_pcm_hw_params *params, struct snd_pcm_hw_rule *rule) @@ -2393,20 +2282,16 @@ constraint_list). You can build a rule like this: } -Then you need to call this function to add your rule: - -:: +Then you need to call this function to add your rule:: snd_pcm_hw_rule_add(substream->runtime, 0, SNDRV_PCM_HW_PARAM_CHANNELS, hw_rule_channels_by_format, NULL, SNDRV_PCM_HW_PARAM_FORMAT, -1); The rule function is called when an application sets the PCM format, and it refines the number of channels accordingly. But an application may set the number of channels before setting the format. Thus you also need -to define the inverse rule: - -:: +to define the inverse rule:: static int hw_rule_format_by_channels(struct snd_pcm_hw_params *params, struct snd_pcm_hw_rule *rule) @@ -2425,34 +2310,30 @@ to define the inverse rule: } -... and in the open callback: - -:: +... and in the open callback:: snd_pcm_hw_rule_add(substream->runtime, 0, SNDRV_PCM_HW_PARAM_FORMAT, hw_rule_format_by_channels, NULL, SNDRV_PCM_HW_PARAM_CHANNELS, -1); One typical usage of the hw constraints is to align the buffer size -with the period size. As default, ALSA PCM core doesn't enforce the +with the period size. By default, ALSA PCM core doesn't enforce the buffer size to be aligned with the period size. For example, it'd be possible to have a combination like 256 period bytes with 999 buffer bytes. Many device chips, however, require the buffer to be a multiple of periods. In such a case, call :c:func:`snd_pcm_hw_constraint_integer()` for -``SNDRV_PCM_HW_PARAM_PERIODS``. - -:: +``SNDRV_PCM_HW_PARAM_PERIODS``:: snd_pcm_hw_constraint_integer(substream->runtime, SNDRV_PCM_HW_PARAM_PERIODS); This assures that the number of periods is integer, hence the buffer size is aligned with the period size. -The hw constraint is a very much powerful mechanism to define the +The hw constraint is a very powerful mechanism to define the preferred PCM configuration, and there are relevant helpers. I won't give more details here, rather I would like to say, “Luke, use the source.” @@ -2479,9 +2360,7 @@ Definition of Controls To create a new control, you need to define the following three callbacks: ``info``, ``get`` and ``put``. Then, define a -struct snd_kcontrol_new record, such as: - -:: +struct snd_kcontrol_new record, such as:: static struct snd_kcontrol_new my_control = { @@ -2524,7 +2403,7 @@ The ``private_value`` field contains an arbitrary long integer value for this record. When using the generic ``info``, ``get`` and ``put`` callbacks, you can pass a value through this field. If several small numbers are necessary, you can combine them in bitwise. Or, it's -possible to give a pointer (casted to unsigned long) of some record to +possible to store a pointer (casted to unsigned long) of some record in this field, too. The ``tlv`` field can be used to provide metadata about the control; @@ -2591,7 +2470,7 @@ The access flag is the bitmask which specifies the access type of the given control. The default access type is ``SNDRV_CTL_ELEM_ACCESS_READWRITE``, which means both read and write are allowed to this control. When the access flag is omitted (i.e. = 0), it -is considered as ``READWRITE`` access as default. +is considered as ``READWRITE`` access by default. When the control is read-only, pass ``SNDRV_CTL_ELEM_ACCESS_READ`` instead. In this case, you don't have to define the ``put`` callback. @@ -2604,21 +2483,22 @@ If the control value changes frequently (e.g. the VU meter), changed without `Change notification`_. Applications should poll such a control constantly. -When the control is inactive, set the ``INACTIVE`` flag, too. There are -``LOCK`` and ``OWNER`` flags to change the write permissions. +When the control may be updated, but currently has no effect on anything, +setting the ``INACTIVE`` flag may be appropriate. For example, PCM +controls should be inactive while no PCM device is open. + +There are ``LOCK`` and ``OWNER`` flags to change the write permissions. Control Callbacks ----------------- info callback ~~~~~~~~~~~~~ The ``info`` callback is used to get detailed information on this control. This must store the values of the given struct snd_ctl_elem_info object. For example, -for a boolean control with a single element: - -:: +for a boolean control with a single element:: static int snd_myctl_mono_info(struct snd_kcontrol *kcontrol, @@ -2637,13 +2517,11 @@ The ``type`` field specifies the type of the control. There are ``BOOLEAN``, ``INTEGER``, ``ENUMERATED``, ``BYTES``, ``IEC958`` and ``INTEGER64``. The ``count`` field specifies the number of elements in this control. For example, a stereo volume would have count = 2. The -``value`` field is a union, and the values stored are depending on the +``value`` field is a union, and the values stored depend on the type. The boolean and integer types are identical. -The enumerated type is a bit different from others. You'll need to set -the string for the currently given item index. - -:: +The enumerated type is a bit different from the others. You'll need to +set the string for the selectec item index:: static int snd_myctl_enum_info(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_info *uinfo) @@ -2688,13 +2566,10 @@ stereo channel boolean item. get callback ~~~~~~~~~~~~ -This callback is used to read the current value of the control and to -return to user-space. - -For example, - -:: +This callback is used to read the current value of the control, so it +can be returned to user-space. +For example:: static int snd_myctl_get(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol) @@ -2709,39 +2584,32 @@ For example, The ``value`` field depends on the type of control as well as on the info callback. For example, the sb driver uses this field to store the register offset, the bit-shift and the bit-mask. The ``private_value`` -field is set as follows: - -:: +field is set as follows:: .private_value = reg | (shift << 16) | (mask << 24) -and is retrieved in callbacks like - -:: +and is retrieved in callbacks like:: static int snd_sbmixer_get_single(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol) { int reg = kcontrol->private_value & 0xff; int shift = (kcontrol->private_value >> 16) & 0xff; int mask = (kcontrol->private_value >> 24) & 0xff; .... } In the ``get`` callback, you have to fill all the elements if the -control has more than one elements, i.e. ``count > 1``. In the example +control has more than one element, i.e. ``count > 1``. In the example above, we filled only one element (``value.integer.value[0]``) since -it's assumed as ``count = 1``. +``count = 1`` is assumed. put callback ~~~~~~~~~~~~ -This callback is used to write a value from user-space. - -For example, - -:: +This callback is used to write a value coming from user-space. +For example:: static int snd_myctl_put(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol) @@ -2764,23 +2632,21 @@ value is not changed, return 0 instead. If any fatal error happens, return a negative error code as usual. As in the ``get`` callback, when the control has more than one -elements, all elements must be evaluated in this callback, too. +element, all elements must be evaluated in this callback, too. Callbacks are not atomic ~~~~~~~~~~~~~~~~~~~~~~~~ -All these three callbacks are basically not atomic. +All these three callbacks are not-atomic. Control Constructor ------------------- When everything is ready, finally we can create a new control. To create a control, there are two functions to be called, :c:func:`snd_ctl_new1()` and :c:func:`snd_ctl_add()`. -In the simplest way, you can do like this: - -:: +In the simplest way, you can do it like this:: err = snd_ctl_add(card, snd_ctl_new1(&my_control, chip)); if (err < 0) @@ -2798,9 +2664,7 @@ Change Notification ------------------- If you need to change and update a control in the interrupt routine, you -can call :c:func:`snd_ctl_notify()`. For example, - -:: +can call :c:func:`snd_ctl_notify()`. For example:: snd_ctl_notify(card, SNDRV_CTL_EVENT_MASK_VALUE, id_pointer); @@ -2814,13 +2678,11 @@ for hardware volume interrupts. Metadata -------- -To provide information about the dB values of a mixer control, use on of +To provide information about the dB values of a mixer control, use one of the ``DECLARE_TLV_xxx`` macros from ``<sound/tlv.h>`` to define a variable containing this information, set the ``tlv.p`` field to point to this variable, and include the ``SNDRV_CTL_ELEM_ACCESS_TLV_READ`` flag -in the ``access`` field; like this: - -:: +in the ``access`` field; like this:: static DECLARE_TLV_DB_SCALE(db_scale_my_control, -4050, 150, 0); @@ -2910,24 +2772,20 @@ AC97 Constructor ---------------- To create an ac97 instance, first call :c:func:`snd_ac97_bus()` -with an ``ac97_bus_ops_t`` record with callback functions. - -:: +with an ``ac97_bus_ops_t`` record with callback functions:: struct snd_ac97_bus *bus; static struct snd_ac97_bus_ops ops = { .write = snd_mychip_ac97_write, .read = snd_mychip_ac97_read, }; snd_ac97_bus(card, 0, &ops, NULL, &pbus); The bus record is shared among all belonging ac97 instances. -And then call :c:func:`snd_ac97_mixer()` with an struct snd_ac97_template -record together with the bus pointer created above. - -:: +And then call :c:func:`snd_ac97_mixer()` with a struct snd_ac97_template +record together with the bus pointer created above:: struct snd_ac97_template ac97; int err; @@ -2952,9 +2810,7 @@ correspond to the functions for read and write accesses to the hardware low-level codes. The ``read`` callback returns the register value specified in the -argument. - -:: +argument:: static unsigned short snd_mychip_ac97_read(struct snd_ac97 *ac97, unsigned short reg) @@ -2967,9 +2823,7 @@ argument. Here, the chip can be cast from ``ac97->private_data``. Meanwhile, the ``write`` callback is used to set the register -value - -:: +value:: static void snd_mychip_ac97_write(struct snd_ac97 *ac97, unsigned short reg, unsigned short val) @@ -3002,32 +2856,24 @@ Both :c:func:`snd_ac97_write()` and the given register (``AC97_XXX``). The difference between them is that :c:func:`snd_ac97_update()` doesn't write a value if the given value has been already set, while :c:func:`snd_ac97_write()` -always rewrites the value. - -:: +always rewrites the value:: snd_ac97_write(ac97, AC97_MASTER, 0x8080); snd_ac97_update(ac97, AC97_MASTER, 0x8080); :c:func:`snd_ac97_read()` is used to read the value of the given -register. For example, - -:: +register. For example:: value = snd_ac97_read(ac97, AC97_MASTER); :c:func:`snd_ac97_update_bits()` is used to update some bits in -the given register. - -:: +the given register:: snd_ac97_update_bits(ac97, reg, mask, value); Also, there is a function to change the sample rate (of a given register such as ``AC97_PCM_FRONT_DAC_RATE``) when VRA or DRA is supported by the -codec: :c:func:`snd_ac97_set_rate()`. - -:: +codec: :c:func:`snd_ac97_set_rate()`:: snd_ac97_set_rate(ac97, AC97_PCM_FRONT_DAC_RATE, 44100); @@ -3082,9 +2928,7 @@ mpu401 stuff. For example, emu10k1 has its own mpu401 routines. MIDI Constructor ---------------- -To create a rawmidi object, call :c:func:`snd_mpu401_uart_new()`. - -:: +To create a rawmidi object, call :c:func:`snd_mpu401_uart_new()`:: struct snd_rawmidi *rmidi; snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401, port, info_flags, @@ -3129,16 +2973,12 @@ corresponds to the data port. If not, you may change the ``cport`` field of struct snd_mpu401 manually afterward. However, struct snd_mpu401 pointer is not returned explicitly by :c:func:`snd_mpu401_uart_new()`. You -need to cast ``rmidi->private_data`` to struct snd_mpu401 explicitly, - -:: +need to cast ``rmidi->private_data`` to struct snd_mpu401 explicitly:: struct snd_mpu401 *mpu; mpu = rmidi->private_data; -and reset the ``cport`` as you like: - -:: +and reset the ``cport`` as you like:: mpu->cport = my_own_control_port; @@ -3162,9 +3002,7 @@ occurred. In this case, you need to pass the private_data of the returned rawmidi object from :c:func:`snd_mpu401_uart_new()` as the second -argument of :c:func:`snd_mpu401_uart_interrupt()`. - -:: +argument of :c:func:`snd_mpu401_uart_interrupt()`:: snd_mpu401_uart_interrupt(irq, rmidi->private_data, regs); @@ -3188,9 +3026,7 @@ RawMIDI Constructor ------------------- To create a rawmidi device, call the :c:func:`snd_rawmidi_new()` -function: - -:: +function:: struct snd_rawmidi *rmidi; err = snd_rawmidi_new(chip->card, "MyMIDI", 0, outs, ins, &rmidi); @@ -3220,29 +3056,23 @@ output and input at the same time. After the rawmidi device is created, you need to set the operators (callbacks) for each substream. There are helper functions to set the -operators for all the substreams of a device: - -:: +operators for all the substreams of a device:: snd_rawmidi_set_ops(rmidi, SNDRV_RAWMIDI_STREAM_OUTPUT, &snd_mymidi_output_ops); snd_rawmidi_set_ops(rmidi, SNDRV_RAWMIDI_STREAM_INPUT, &snd_mymidi_input_ops); -The operators are usually defined like this: - -:: +The operators are usually defined like this:: static struct snd_rawmidi_ops snd_mymidi_output_ops = { .open = snd_mymidi_output_open, .close = snd_mymidi_output_close, .trigger = snd_mymidi_output_trigger, }; These callbacks are explained in the `RawMIDI Callbacks`_ section. If there are more than one substream, you should give a unique name to -each of them: - -:: +each of them:: struct snd_rawmidi_substream *substream; list_for_each_entry(substream, @@ -3260,9 +3090,7 @@ device can be accessed as ``substream->rmidi->private_data``. If there is more than one port, your callbacks can determine the port index from the struct snd_rawmidi_substream data passed to each -callback: - -:: +callback:: struct snd_rawmidi_substream *substream; int index = substream->number; @@ -3307,23 +3135,19 @@ of bytes that have been read; this will be less than the number of bytes requested when there are no more data in the buffer. After the data have been transmitted successfully, call :c:func:`snd_rawmidi_transmit_ack()` to remove the data from the -substream buffer: - -:: +substream buffer:: unsigned char data; while (snd_rawmidi_transmit_peek(substream, &data, 1) == 1) { if (snd_mychip_try_to_transmit(data)) snd_rawmidi_transmit_ack(substream, 1); else break; /* hardware FIFO full */ } If you know beforehand that the hardware will accept data, you can use the :c:func:`snd_rawmidi_transmit()` function which reads some -data and removes them from the buffer at once: - -:: +data and removes them from the buffer at once:: while (snd_mychip_transmit_possible()) { unsigned char data; @@ -3358,9 +3182,7 @@ The ``trigger`` callback must not sleep; the actual reading of data from the device is usually done in an interrupt handler. When data reception is enabled, your interrupt handler should call -:c:func:`snd_rawmidi_receive()` for all received data: - -:: +:c:func:`snd_rawmidi_receive()` for all received data:: void snd_mychip_midi_interrupt(...) { @@ -3406,9 +3228,7 @@ whereas in OSS compatible mode, FM registers can be accessed with the OSS direct-FM compatible API in ``/dev/dmfmX`` device. To create the OPL3 component, you have two functions to call. The first -one is a constructor for the ``opl3_t`` instance. - -:: +one is a constructor for the ``opl3_t`` instance:: struct snd_opl3 *opl3; snd_opl3_create(card, lport, rport, OPL3_HW_OPL3_XXX, @@ -3426,9 +3246,7 @@ the opl3 module will allocate the specified ports by itself. When the accessing the hardware requires special method instead of the standard I/O access, you can create opl3 instance separately with -:c:func:`snd_opl3_new()`. - -:: +:c:func:`snd_opl3_new()`:: struct snd_opl3 *opl3; snd_opl3_new(card, OPL3_HW_OPL3_XXX, &opl3); @@ -3445,9 +3263,7 @@ proper state. Note that :c:func:`snd_opl3_create()` always calls it internally. If the opl3 instance is created successfully, then create a hwdep device -for this opl3. - -:: +for this opl3:: struct snd_hwdep *opl3hwdep; snd_opl3_hwdep_new(opl3, 0, 1, &opl3hwdep); @@ -3469,40 +3285,32 @@ the micro code. In such a case, you can create a hwdep ``isa/sb/sb16_csp.c``. The creation of the ``hwdep`` instance is done via -:c:func:`snd_hwdep_new()`. - -:: +:c:func:`snd_hwdep_new()`:: struct snd_hwdep *hw; snd_hwdep_new(card, "My HWDEP", 0, &hw); where the third argument is the index number. You can then pass any pointer value to the ``private_data``. If you -assign a private data, you should define the destructor, too. The -destructor function is set in the ``private_free`` field. - -:: +assign private data, you should define a destructor, too. The +destructor function is set in the ``private_free`` field:: struct mydata *p = kmalloc(sizeof(*p), GFP_KERNEL); hw->private_data = p; hw->private_free = mydata_free; -and the implementation of the destructor would be: - -:: +and the implementation of the destructor would be:: static void mydata_free(struct snd_hwdep *hw) { struct mydata *p = hw->private_data; kfree(p); } The arbitrary file operations can be defined for this instance. The file operators are defined in the ``ops`` table. For example, assume that -this chip needs an ioctl. - -:: +this chip needs an ioctl:: hw->ops.open = mydata_open; hw->ops.ioctl = mydata_ioctl; @@ -3552,92 +3360,87 @@ Buffer Types ALSA provides several different buffer allocation functions depending on the bus and the architecture. All these have a consistent API. The -allocation of physically-contiguous pages is done via +allocation of physically-contiguous pages is done via the :c:func:`snd_malloc_xxx_pages()` function, where xxx is the bus type. -The allocation of pages with fallback is -:c:func:`snd_malloc_xxx_pages_fallback()`. This function tries -to allocate the specified pages but if the pages are not available, it -tries to reduce the page sizes until enough space is found. +The allocation of pages with fallback is done via +:c:func:`snd_dma_alloc_pages_fallback()`. This function tries +to allocate the specified number of pages, but if not enough pages are +available, it tries to reduce the request size until enough space +is found, down to one page. -The release the pages, call :c:func:`snd_free_xxx_pages()` +To release the pages, call the :c:func:`snd_dma_free_pages()` function. Usually, ALSA drivers try to allocate and reserve a large contiguous -physical space at the time the module is loaded for the later use. This +physical space at the time the module is loaded for later use. This is called “pre-allocation”. As already written, you can call the -following function at pcm instance construction time (in the case of PCI -bus). - -:: +following function at PCM instance construction time (in the case of PCI +bus):: snd_pcm_lib_preallocate_pages_for_all(pcm, SNDRV_DMA_TYPE_DEV, &pci->dev, size, max); -where ``size`` is the byte size to be pre-allocated and the ``max`` is -the maximum size to be changed via the ``prealloc`` proc file. The +where ``size`` is the byte size to be pre-allocated and ``max`` is +the maximum size settable via the ``prealloc`` proc file. The allocator will try to get an area as large as possible within the given size. The second argument (type) and the third argument (device pointer) are dependent on the bus. For normal devices, pass the device pointer (typically identical as ``card->dev``) to the third argument with ``SNDRV_DMA_TYPE_DEV`` type. -For the continuous buffer unrelated to the +A continuous buffer unrelated to the bus can be pre-allocated with ``SNDRV_DMA_TYPE_CONTINUOUS`` type. You can pass NULL to the device pointer in that case, which is the -default mode implying to allocate with ``GFP_KERNEL`` flag. +default mode implying to allocate with the ``GFP_KERNEL`` flag. If you need a restricted (lower) address, set up the coherent DMA mask bits for the device, and pass the device pointer, like the normal device memory allocations. For this type, it's still allowed to pass NULL to the device pointer, too, if no address restriction is needed. For the scatter-gather buffers, use ``SNDRV_DMA_TYPE_DEV_SG`` with the device pointer (see the `Non-Contiguous Buffers`_ section). Once the buffer is pre-allocated, you can use the allocator in the -``hw_params`` callback: - -:: +``hw_params`` callback:: snd_pcm_lib_malloc_pages(substream, size); Note that you have to pre-allocate to use this function. -Most of drivers use, though, rather the newly introduced "managed -buffer allocation mode" instead of the manual allocation or release. +But most drivers use the "managed buffer allocation mode" instead +of manual allocation and release. This is done by calling :c:func:`snd_pcm_set_managed_buffer_all()` -instead of :c:func:`snd_pcm_lib_preallocate_pages_for_all()`. - -:: +instead of :c:func:`snd_pcm_lib_preallocate_pages_for_all()`:: snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_DEV, &pci->dev, size, max); -where passed arguments are identical in both functions. +where the passed arguments are identical for both functions. The difference in the managed mode is that PCM core will call :c:func:`snd_pcm_lib_malloc_pages()` internally already before calling the PCM ``hw_params`` callback, and call :c:func:`snd_pcm_lib_free_pages()` after the PCM ``hw_free`` callback automatically. So the driver doesn't have to call these functions explicitly in its callback any -longer. This made many driver code having NULL ``hw_params`` and +longer. This allows many drivers to have NULL ``hw_params`` and ``hw_free`` entries. External Hardware Buffers ------------------------- -Some chips have their own hardware buffers and the DMA transfer from the +Some chips have their own hardware buffers and DMA transfer from the host memory is not available. In such a case, you need to either 1) copy/set the audio data directly to the external hardware buffer, or 2) make an intermediate buffer and copy/set the data from it to the external hardware buffer in interrupts (or in tasklets, preferably). The first case works fine if the external hardware buffer is large enough. This method doesn't need any extra buffers and thus is more -effective. You need to define the ``copy_user`` and ``copy_kernel`` -callbacks for the data transfer, in addition to ``fill_silence`` +efficient. You need to define the ``copy_user`` and ``copy_kernel`` +callbacks for the data transfer, in addition to the ``fill_silence`` callback for playback. However, there is a drawback: it cannot be mmapped. The examples are GUS's GF1 PCM or emu8000's wavetable PCM. @@ -3651,157 +3454,136 @@ buffer instead of the host memory. In this case, mmap is available only on certain architectures like the Intel one. In non-mmap mode, the data cannot be transferred as in the normal way. Thus you need to define the ``copy_user``, ``copy_kernel`` and ``fill_silence`` callbacks as well, -as in the cases above. The examples are found in ``rme32.c`` and +as in the cases above. Examples are found in ``rme32.c`` and ``rme96.c``. The implementation of the ``copy_user``, ``copy_kernel`` and ``silence`` callbacks depends upon whether the hardware supports interleaved or non-interleaved samples. The ``copy_user`` callback is -defined like below, a bit differently depending whether the direction -is playback or capture: - -:: +defined like below, a bit differently depending on whether the direction +is playback or capture:: static int playback_copy_user(struct snd_pcm_substream *substream, int channel, unsigned long pos, void __user *src, unsigned long count); static int capture_copy_user(struct snd_pcm_substream *substream, int channel, unsigned long pos, void __user *dst, unsigned long count); In the case of interleaved samples, the second argument (``channel``) is -not used. The third argument (``pos``) points the current position -offset in bytes. +not used. The third argument (``pos``) specifies the position in bytes. The meaning of the fourth argument is different between playback and capture. For playback, it holds the source data pointer, and for capture, it's the destination data pointer. The last argument is the number of bytes to be copied. What you have to do in this callback is again different between playback and capture directions. In the playback case, you copy the given amount of data (``count``) at the specified pointer (``src``) to the specified -offset (``pos``) on the hardware buffer. When coded like memcpy-like -way, the copy would be like: - -:: +offset (``pos``) in the hardware buffer. When coded like memcpy-like +way, the copy would look like:: my_memcpy_from_user(my_buffer + pos, src, count); For the capture direction, you copy the given amount of data (``count``) -at the specified offset (``pos``) on the hardware buffer to the -specified pointer (``dst``). - -:: +at the specified offset (``pos``) in the hardware buffer to the +specified pointer (``dst``):: my_memcpy_to_user(dst, my_buffer + pos, count); -Here the functions are named as ``from_user`` and ``to_user`` because +Here the functions are named ``from_user`` and ``to_user`` because it's the user-space buffer that is passed to these callbacks. That -is, the callback is supposed to copy from/to the user-space data +is, the callback is supposed to copy data from/to the user-space directly to/from the hardware buffer. Careful readers might notice that these callbacks receive the arguments in bytes, not in frames like other callbacks. It's because -it would make coding easier like the examples above, and also it makes -easier to unify both the interleaved and non-interleaved cases, as -explained in the following. +this makes coding easier like in the examples above, and also it makes +it easier to unify both the interleaved and non-interleaved cases, as +explained below. In the case of non-interleaved samples, the implementation will be a bit -more complicated. The callback is called for each channel, passed by -the second argument, so totally it's called for N-channels times per -transfer. +more complicated. The callback is called for each channel, passed in +the second argument, so in total it's called N times per transfer. -The meaning of other arguments are almost same as the interleaved -case. The callback is supposed to copy the data from/to the given -user-space buffer, but only for the given channel. For the detailed -implementations, please check ``isa/gus/gus_pcm.c`` or -"pci/rme9652/rme9652.c" as examples. +The meaning of the other arguments are almost the same as in the +interleaved case. The callback is supposed to copy the data from/to +the given user-space buffer, but only for the given channel. For +details, please check ``isa/gus/gus_pcm.c`` or ``pci/rme9652/rme9652.c`` +as examples. -The above callbacks are the copy from/to the user-space buffer. There -are some cases where we want copy from/to the kernel-space buffer -instead. In such a case, ``copy_kernel`` callback is called. It'd -look like: - -:: +The above callbacks are the copies from/to the user-space buffer. There +are some cases where we want to copy from/to the kernel-space buffer +instead. In such a case, the ``copy_kernel`` callback is called. It'd +look like:: static int playback_copy_kernel(struct snd_pcm_substream *substream, int channel, unsigned long pos, void *src, unsigned long count); static int capture_copy_kernel(struct snd_pcm_substream *substream, int channel, unsigned long pos, void *dst, unsigned long count); As found easily, the only difference is that the buffer pointer is -without ``__user`` prefix; that is, a kernel-buffer pointer is passed +without a ``__user`` prefix; that is, a kernel-buffer pointer is passed in the fourth argument. Correspondingly, the implementation would be -a version without the user-copy, such as: - -:: +a version without the user-copy, such as:: my_memcpy(my_buffer + pos, src, count); Usually for the playback, another callback ``fill_silence`` is defined. It's implemented in a similar way as the copy callbacks -above: - -:: +above:: static int silence(struct snd_pcm_substream *substream, int channel, unsigned long pos, unsigned long count); The meanings of arguments are the same as in the ``copy_user`` and ``copy_kernel`` callbacks, although there is no buffer pointer argument. In the case of interleaved samples, the channel argument has -no meaning, as well as on ``copy_*`` callbacks. +no meaning, as for the ``copy_*`` callbacks. -The role of ``fill_silence`` callback is to set the given amount -(``count``) of silence data at the specified offset (``pos``) on the +The role of the ``fill_silence`` callback is to set the given amount +(``count``) of silence data at the specified offset (``pos``) in the hardware buffer. Suppose that the data format is signed (that is, the silent-data is 0), and the implementation using a memset-like function -would be like: - -:: +would look like:: my_memset(my_buffer + pos, 0, count); In the case of non-interleaved samples, again, the implementation -becomes a bit more complicated, as it's called N-times per transfer +becomes a bit more complicated, as it's called N times per transfer for each channel. See, for example, ``isa/gus/gus_pcm.c``. Non-Contiguous Buffers ---------------------- -If your hardware supports the page table as in emu10k1 or the buffer -descriptors as in via82xx, you can use the scatter-gather (SG) DMA. ALSA +If your hardware supports a page table as in emu10k1 or buffer +descriptors as in via82xx, you can use scatter-gather (SG) DMA. ALSA provides an interface for handling SG-buffers. The API is provided in ``<sound/pcm.h>``. For creating the SG-buffer handler, call :c:func:`snd_pcm_set_managed_buffer()` or :c:func:`snd_pcm_set_managed_buffer_all()` with -``SNDRV_DMA_TYPE_DEV_SG`` in the PCM constructor like other PCI -pre-allocator. You need to pass ``&pci->dev``, where pci is -the struct pci_dev pointer of the chip as -well. - -:: +``SNDRV_DMA_TYPE_DEV_SG`` in the PCM constructor like for other PCI +pre-allocations. You need to pass ``&pci->dev``, where pci is +the struct pci_dev pointer of the chip as well:: snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_DEV_SG, &pci->dev, size, max); The ``struct snd_sg_buf`` instance is created as -``substream->dma_private`` in turn. You can cast the pointer like: - -:: +``substream->dma_private`` in turn. You can cast the pointer like:: struct snd_sg_buf *sgbuf = (struct snd_sg_buf *)substream->dma_private; -Then in :c:func:`snd_pcm_lib_malloc_pages()` call, the common SG-buffer +Then in the :c:func:`snd_pcm_lib_malloc_pages()` call, the common SG-buffer handler will allocate the non-contiguous kernel pages of the given size -and map them onto the virtually contiguous memory. The virtual pointer -is addressed in runtime->dma_area. The physical address +and map them as virtually contiguous memory. The virtual pointer +is addressed via runtime->dma_area. The physical address (``runtime->dma_addr``) is set to zero, because the buffer is physically non-contiguous. The physical address table is set up in ``sgbuf->table``. You can get the physical address at a certain offset @@ -3814,36 +3596,32 @@ Vmalloc'ed Buffers ------------------ It's possible to use a buffer allocated via :c:func:`vmalloc()`, for -example, for an intermediate buffer. In the recent version of kernel, -you can simply allocate it via standard -:c:func:`snd_pcm_lib_malloc_pages()` and co after setting up the -buffer preallocation with ``SNDRV_DMA_TYPE_VMALLOC`` type. - -:: +example, for an intermediate buffer. +You can simply allocate it via the standard +:c:func:`snd_pcm_lib_malloc_pages()` and co. after setting up the +buffer preallocation with ``SNDRV_DMA_TYPE_VMALLOC`` type:: snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_VMALLOC, NULL, 0, 0); -The NULL is passed to the device pointer argument, which indicates -that the default pages (GFP_KERNEL and GFP_HIGHMEM) will be +NULL is passed as the device pointer argument, which indicates +that default pages (GFP_KERNEL and GFP_HIGHMEM) will be allocated. -Also, note that zero is passed to both the size and the max size -arguments here. Since each vmalloc call should succeed at any time, +Also, note that zero is passed as both the size and the max size +argument here. Since each vmalloc call should succeed at any time, we don't need to pre-allocate the buffers like other continuous pages. Proc Interface ============== ALSA provides an easy interface for procfs. The proc files are very useful for debugging. I recommend you set up proc files if you write a driver and want to get a running status or register dumps. The API is found in ``<sound/info.h>``. -To create a proc file, call :c:func:`snd_card_proc_new()`. - -:: +To create a proc file, call :c:func:`snd_card_proc_new()`:: struct snd_info_entry *entry; int err = snd_card_proc_new(card, "my-file", &entry); @@ -3859,79 +3637,66 @@ automatically in the card registration and release functions. When the creation is successful, the function stores a new instance in the pointer given in the third argument. It is initialized as a text proc file for read only. To use this proc file as a read-only text file -as it is, set the read callback with a private data via -:c:func:`snd_info_set_text_ops()`. - -:: +as-is, set the read callback with private data via +:c:func:`snd_info_set_text_ops()`:: snd_info_set_text_ops(entry, chip, my_proc_read); where the second argument (``chip``) is the private data to be used in -the callbacks. The third parameter specifies the read buffer size and +the callback. The third parameter specifies the read buffer size and the fourth (``my_proc_read``) is the callback function, which is -defined like - -:: +defined like:: static void my_proc_read(struct snd_info_entry *entry, struct snd_info_buffer *buffer); In the read callback, use :c:func:`snd_iprintf()` for output strings, which works just like normal :c:func:`printf()`. For -example, - -:: +example:: static void my_proc_read(struct snd_info_entry *entry, struct snd_info_buffer *buffer) { struct my_chip *chip = entry->private_data; snd_iprintf(buffer, "This is my chip!\n"); snd_iprintf(buffer, "Port = %ld\n", chip->port); } -The file permissions can be changed afterwards. As default, it's set as +The file permissions can be changed afterwards. By default, they are read only for all users. If you want to add write permission for the -user (root as default), do as follows: - -:: +user (root by default), do as follows:: entry->mode = S_IFREG | S_IRUGO | S_IWUSR; -and set the write buffer size and the callback - -:: +and set the write buffer size and the callback:: entry->c.text.write = my_proc_write; -For the write callback, you can use :c:func:`snd_info_get_line()` +In the write callback, you can use :c:func:`snd_info_get_line()` to get a text line, and :c:func:`snd_info_get_str()` to retrieve a string from the line. Some examples are found in ``core/oss/mixer_oss.c``, core/oss/and ``pcm_oss.c``. -For a raw-data proc-file, set the attributes as follows: - -:: +For a raw-data proc-file, set the attributes as follows:: static const struct snd_info_entry_ops my_file_io_ops = { .read = my_file_io_read, }; entry->content = SNDRV_INFO_CONTENT_DATA; entry->private_data = chip; entry->c.ops = &my_file_io_ops; entry->size = 4096; entry->mode = S_IFREG | S_IRUGO; -For the raw data, ``size`` field must be set properly. This specifies +For raw data, ``size`` field must be set properly. This specifies the maximum size of the proc file access. The read/write callbacks of raw mode are more direct than the text mode. You need to use a low-level I/O functions such as -:c:func:`copy_from_user()` and :c:func:`copy_to_user()` to transfer the data. - -:: +:c:func:`copy_from_user()` and :c:func:`copy_to_user()` to transfer the +data:: static ssize_t my_file_io_read(struct snd_info_entry *entry, void *file_private_data, @@ -3956,37 +3721,33 @@ Power Management If the chip is supposed to work with suspend/resume functions, you need to add power-management code to the driver. The additional code for power-management should be ifdef-ed with ``CONFIG_PM``, or annotated -with __maybe_unused attribute; otherwise the compiler will complain -you. +with __maybe_unused attribute; otherwise the compiler will complain. If the driver *fully* supports suspend/resume that is, the device can be properly resumed to its state when suspend was called, you can set the -``SNDRV_PCM_INFO_RESUME`` flag in the pcm info field. Usually, this is +``SNDRV_PCM_INFO_RESUME`` flag in the PCM info field. Usually, this is possible when the registers of the chip can be safely saved and restored to RAM. If this is set, the trigger callback is called with ``SNDRV_PCM_TRIGGER_RESUME`` after the resume callback completes. Even if the driver doesn't support PM fully but partial suspend/resume is still possible, it's still worthy to implement suspend/resume callbacks. In such a case, applications would reset the status by calling :c:func:`snd_pcm_prepare()` and restart the stream appropriately. Hence, you can define suspend/resume callbacks below but -don't set ``SNDRV_PCM_INFO_RESUME`` info flag to the PCM. +don't set the ``SNDRV_PCM_INFO_RESUME`` info flag to the PCM. Note that the trigger with SUSPEND can always be called when :c:func:`snd_pcm_suspend_all()` is called, regardless of the ``SNDRV_PCM_INFO_RESUME`` flag. The ``RESUME`` flag affects only the behavior of :c:func:`snd_pcm_resume()`. (Thus, in theory, ``SNDRV_PCM_TRIGGER_RESUME`` isn't needed to be handled in the trigger callback when no ``SNDRV_PCM_INFO_RESUME`` flag is set. But, it's better to keep it for compatibility reasons.) -In the earlier version of ALSA drivers, a common power-management layer -was provided, but it has been removed. The driver needs to define the +The driver needs to define the suspend/resume hooks according to the bus the device is connected to. In -the case of PCI drivers, the callbacks look like below: - -:: +the case of PCI drivers, the callbacks look like below:: static int __maybe_unused snd_my_suspend(struct device *dev) { @@ -3999,7 +3760,7 @@ the case of PCI drivers, the callbacks look like below: return 0; } -The scheme of the real suspend job is as follows. +The scheme of the real suspend job is as follows: 1. Retrieve the card and the chip data. @@ -4013,9 +3774,7 @@ The scheme of the real suspend job is as follows. 5. Stop the hardware if necessary. -A typical code would be like: - -:: +Typical code would look like:: static int __maybe_unused mychip_suspend(struct device *dev) { @@ -4034,24 +3793,22 @@ A typical code would be like: } -The scheme of the real resume job is as follows. +The scheme of the real resume job is as follows: 1. Retrieve the card and the chip data. 2. Re-initialize the chip. 3. Restore the saved registers if necessary. -4. Resume the mixer, e.g. calling :c:func:`snd_ac97_resume()`. +4. Resume the mixer, e.g. by calling :c:func:`snd_ac97_resume()`. 5. Restart the hardware (if any). 6. Call :c:func:`snd_power_change_state()` with ``SNDRV_CTL_POWER_D0`` to notify the processes. -A typical code would be like: - -:: +Typical code would look like:: static int __maybe_unused mychip_resume(struct pci_dev *pci) { @@ -4078,9 +3835,7 @@ been already suspended via its own PM ops calling OK, we have all callbacks now. Let's set them up. In the initialization of the card, make sure that you can get the chip data from the card instance, typically via ``private_data`` field, in case you created the -chip data individually. - -:: +chip data individually:: static int snd_mychip_probe(struct pci_dev *pci, const struct pci_device_id *pci_id) @@ -4100,9 +3855,7 @@ chip data individually. } When you created the chip data with :c:func:`snd_card_new()`, it's -anyway accessible via ``private_data`` field. - -:: +anyway accessible via ``private_data`` field:: static int snd_mychip_probe(struct pci_dev *pci, const struct pci_device_id *pci_id) @@ -4119,14 +3872,12 @@ anyway accessible via ``private_data`` field. .... } -If you need a space to save the registers, allocate the buffer for it +If you need space to save the registers, allocate the buffer for it here, too, since it would be fatal if you cannot allocate a memory in the suspend phase. The allocated buffer should be released in the corresponding destructor. -And next, set suspend/resume callbacks to the pci_driver. - -:: +And next, set suspend/resume callbacks to the pci_driver:: static SIMPLE_DEV_PM_OPS(snd_my_pm_ops, mychip_suspend, mychip_resume); @@ -4146,9 +3897,7 @@ have the ``index``, ``id`` and ``enable`` options. If the module supports multiple cards (usually up to 8 = ``SNDRV_CARDS`` cards), they should be arrays. The default initial values are defined -already as constants for easier programming: - -:: +already as constants for easier programming:: static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX; static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR; @@ -4162,9 +3911,7 @@ The module parameters must be declared with the standard ``module_param()``, ``module_param_array()`` and :c:func:`MODULE_PARM_DESC()` macros. -The typical coding would be like below: - -:: +Typical code would look as below:: #define CARD_NAME "My Chip" @@ -4177,9 +3924,7 @@ The typical coding would be like below: Also, don't forget to define the module description and the license. Especially, the recent modprobe requires to define the -module license as GPL, etc., otherwise the system is shown as “tainted”. - -:: +module license as GPL, etc., otherwise the system is shown as “tainted”:: MODULE_DESCRIPTION("Sound driver for My Chip"); MODULE_LICENSE("GPL"); @@ -4242,50 +3987,50 @@ Driver with A Single Source File 1. Modify sound/pci/Makefile - Suppose you have a file xyz.c. Add the following two lines - -:: + Suppose you have a file xyz.c. Add the following two lines:: snd-xyz-objs := xyz.o obj-$(CONFIG_SND_XYZ) += snd-xyz.o 2. Create the Kconfig entry - Add the new entry of Kconfig for your xyz driver. config SND_XYZ - tristate "Foobar XYZ" depends on SND select SND_PCM help Say Y here - to include support for Foobar XYZ soundcard. To compile this driver - as a module, choose M here: the module will be called snd-xyz. the - line, select SND_PCM, specifies that the driver xyz supports PCM. In - addition to SND_PCM, the following components are supported for - select command: SND_RAWMIDI, SND_TIMER, SND_HWDEP, - SND_MPU401_UART, SND_OPL3_LIB, SND_OPL4_LIB, SND_VX_LIB, - SND_AC97_CODEC. Add the select command for each supported - component. + Add the new entry of Kconfig for your xyz driver:: - Note that some selections imply the lowlevel selections. For example, - PCM includes TIMER, MPU401_UART includes RAWMIDI, AC97_CODEC - includes PCM, and OPL3_LIB includes HWDEP. You don't need to give - the lowlevel selections again. + config SND_XYZ + tristate "Foobar XYZ" + depends on SND + select SND_PCM + help + Say Y here to include support for Foobar XYZ soundcard. + To compile this driver as a module, choose M here: + the module will be called snd-xyz. - For the details of Kconfig script, refer to the kbuild documentation. +The line ``select SND_PCM`` specifies that the driver xyz supports PCM. +In addition to SND_PCM, the following components are supported for +select command: SND_RAWMIDI, SND_TIMER, SND_HWDEP, SND_MPU401_UART, +SND_OPL3_LIB, SND_OPL4_LIB, SND_VX_LIB, SND_AC97_CODEC. +Add the select command for each supported component. + +Note that some selections imply the lowlevel selections. For example, +PCM includes TIMER, MPU401_UART includes RAWMIDI, AC97_CODEC +includes PCM, and OPL3_LIB includes HWDEP. You don't need to give +the lowlevel selections again. + +For the details of Kconfig script, refer to the kbuild documentation. Drivers with Several Source Files --------------------------------- Suppose that the driver snd-xyz have several source files. They are located in the new subdirectory, sound/pci/xyz. 1. Add a new directory (``sound/pci/xyz``) in ``sound/pci/Makefile`` - as below - -:: + as below:: obj-$(CONFIG_SND) += sound/pci/xyz/ -2. Under the directory ``sound/pci/xyz``, create a Makefile - -:: +2. Under the directory ``sound/pci/xyz``, create a Makefile:: snd-xyz-objs := xyz.o abc.o def.o obj-$(CONFIG_SND_XYZ) += snd-xyz.o -- 2.40.0.152.g15d061e6df

2 1