- Alsa-devel - mailman.alsa-project.org

Re: Re: [PATCH v2] ASoC: codecs: Check for error pointer after calling devm_regmap_init_mmio
by Jiasheng Jiang 21 Jan '22

21 Jan '22

On Thu, Jan 20, 2022 at 00:46:45AM +0800, Mark Brown wrote: >> Since the possible failure of the devm_regmap_init_mmio(), it will >> return error pointer and be assigned to the regmap. >> Then the error pointer will be dereferenced. >> For example rx->regmap will be used in rx_macro_mclk_enable(). >> Therefore, it should be better to check it. > > This doesn't apply against current code, please check and resend. I am really sorry. I have already try my best to find the latest code but fails. Please give me the url or the git repository. Sincerely thanks, Jiang

2 1

SSL 2+ playback device didn't work (device or resource busy)
by Mikhail Gavrilov 21 Jan '22

21 Jan '22

Hi. Got a brand new SSL 2+ sound card today. If the recording works (not ideally) I would like to work with each channel both separately and in stereo mode. That playback does not work at all. The device is defined as a quad channel and it would be better to see this device as two separated stereo devices. $ systemctl --user stop wireplumber.service $ aplay --device sysdefault:CARD=ILDSP ~/Music/Modern\ CD/01.\ I\ have\ found\ my\ love\ in\ you.wav Playing WAVE '/home/mikhail/Music/Modern CD/01. I have found my love in you.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo ^CAborted by signal Interrupt... aplay: pcm_write:2127: write error: Interrupted system call $ aplay --device sysdefault:CARD=S2 ~/Music/Modern\ CD/01.\ I\ have\ found\ my\ love\ in\ you.wav ALSA lib pcm_dmix.c:1032:(snd_pcm_dmix_open) unable to open slave aplay: main:831: audio open error: Device or resource busy $ aplay --device sysdefault:CARD=S2 ~/Music/Modern\ CD/01.\ I\ have\ found\ my\ love\ in\ you.wav ALSA lib pcm_dmix.c:1032:(snd_pcm_dmix_open) unable to open slave aplay: main:831: audio open error: Device or resource busy $ systemctl --user start wireplumber.service http://alsa-project.org/db/?f=99ecd60a74fe21e14262ec53475437b413ae5602 -- Best Regards, Mike Gavrilov.

1 0

[PATCH v4 0/9] Support Spi in i2c-multi-instantiate driver
by Stefan Binding 21 Jan '22

21 Jan '22

Add support for SPI bus in the i2c-multi-instantiate driver as upcoming laptops will need to multi instantiate SPI devices from a single device node, which has multiple SpiSerialBus entries at the ACPI table. With the new SPI support, i2c-multi-instantiate becomes bus-multi-instantiate and is moved to the ACPI folder. The intention is to support the SPI bus by re-using the current I2C multi instantiate, instead of creating a new SPI multi instantiate, to make it possible for peripherals that can be controlled by I2C or SPI to have the same HID at the ACPI table. The new driver (Bus multi instantiate, bmi) checks for the hard-coded bus type and returns -ENODEV in case of zero devices found for that bus. In the case of automatic bus detection, the driver will give preference to I2C. The expectation is for a device node in the ACPI table to have multiple I2cSerialBus only or multiple SpiSerialBus only, not a mix of both; and for the case where there are both entries in one device node, only the I2C ones would be probed. This new bus multi instantiate will be used in CS35L41 HDA new driver. Changes since V2: - Moved bus-multi-instantiate back into platform/x86 Lucas Tanure (4): platform/x86: i2c-multi-instantiate: Rename it for a generic bus driver name platform/x86: bus-multi-instantiate: Reorganize I2C functions ALSA: hda/realtek: Add support for HP Laptops ACPI / scan: Create platform device for CS35L41 Stefan Binding (5): spi: Make spi_alloc_device and spi_add_device public again spi: Create helper API to lookup ACPI info for spi device spi: Support selection of the index of the ACPI Spi Resource before alloc spi: Add API to count spi acpi resources platform/x86: bus-multi-instantiate: Add SPI support MAINTAINERS | 4 +- drivers/acpi/scan.c | 16 +- drivers/platform/x86/Kconfig | 14 +- drivers/platform/x86/Makefile | 2 +- drivers/platform/x86/bus-multi-instantiate.c | 369 +++++++++++++++++++ drivers/platform/x86/i2c-multi-instantiate.c | 174 --------- drivers/spi/spi.c | 142 ++++++- include/linux/spi/spi.h | 32 ++ sound/pci/hda/patch_realtek.c | 43 ++- 9 files changed, 588 insertions(+), 208 deletions(-) create mode 100644 drivers/platform/x86/bus-multi-instantiate.c delete mode 100644 drivers/platform/x86/i2c-multi-instantiate.c -- 2.25.1

4 26

[PATCH 0/3] ASOC: cs42l42: Add support for system suspend
by Richard Fitzgerald 21 Jan '22

21 Jan '22

Add system suspend and resume handlers so that the cs42l42 is cleanly put into power-off state during system suspend and the registers are restored in resume. The first two patches separate out two small changes that can stand alone and are needed to enable the system suspend implementation: 1) Don't rely on there being a jack unplug IRQ before a plug IRQ. There won't be if the unplug and plug happened while in system suspend. 2) Put a mutex around the entire IRQ handling so that the suspend can ensure the last run of the IRQ handler has completed before it powers down. Richard Fitzgerald (3): ASoC: cs42l42: Report full jack status when plug is detected ASoC: cs42l42: Change jack_detect_mutex to a lock of all IRQ handling ASoC: cs42l42: Handle system suspend sound/soc/codecs/cs42l42.c | 164 ++++++++++++++++++++++++++++++++++++++++++--- sound/soc/codecs/cs42l42.h | 7 +- 2 files changed, 161 insertions(+), 10 deletions(-) -- 2.11.0

1 4

[PATCH] dt-bindings: mfd: cirrus,madera: Fix 'interrupts' in example
by Rob Herring 21 Jan '22

21 Jan '22

The 'interrupts' properties takes an irq number, not a phandle, and 'interrupt-parent' isn't needed in examples. --- Documentation/devicetree/bindings/mfd/cirrus,madera.yaml | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/Documentation/devicetree/bindings/mfd/cirrus,madera.yaml b/Documentation/devicetree/bindings/mfd/cirrus,madera.yaml index 5dce62a7eff2..68c75a517c92 100644 --- a/Documentation/devicetree/bindings/mfd/cirrus,madera.yaml +++ b/Documentation/devicetree/bindings/mfd/cirrus,madera.yaml @@ -245,8 +245,7 @@ examples: interrupt-controller; #interrupt-cells = <2>; - interrupts = <&host_irq1>; - interrupt-parent = <&gic>; + interrupts = <4 1 0>; gpio-controller; #gpio-cells = <2>; -- 2.32.0

3 3

[PATCH] dt-bindings: Drop unnecessary pinctrl properties
by Rob Herring 20 Jan '22

20 Jan '22

For a single pinctrl mode, it is not necessary to define pinctrl properties as the tools always allow pinctrl properties. Signed-off-by: Rob Herring <robh(a)kernel.org> --- .../display/rockchip/rockchip,rk3066-hdmi.yaml | 8 -------- Documentation/devicetree/bindings/input/gpio-keys.yaml | 6 ------ .../devicetree/bindings/pinctrl/cirrus,lochnagar.yaml | 9 --------- .../devicetree/bindings/pinctrl/cirrus,madera.yaml | 10 ---------- .../devicetree/bindings/sound/samsung-i2s.yaml | 6 ------ 5 files changed, 39 deletions(-) diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3066-hdmi.yaml b/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3066-hdmi.yaml index 008c144257cb..1a68a940d165 100644 --- a/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3066-hdmi.yaml +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3066-hdmi.yaml @@ -26,14 +26,6 @@ properties: clock-names: const: hclk - pinctrl-0: - maxItems: 2 - - pinctrl-names: - const: default - description: - Switch the iomux for the HPD/I2C pins to HDMI function. - power-domains: maxItems: 1 diff --git a/Documentation/devicetree/bindings/input/gpio-keys.yaml b/Documentation/devicetree/bindings/input/gpio-keys.yaml index dbe7ecc19ccb..7fe1966ea28a 100644 --- a/Documentation/devicetree/bindings/input/gpio-keys.yaml +++ b/Documentation/devicetree/bindings/input/gpio-keys.yaml @@ -88,12 +88,6 @@ patternProperties: which can be disabled to suppress events from the button. type: boolean - pinctrl-0: - maxItems: 1 - - pinctrl-names: - maxItems: 1 - required: - linux,code diff --git a/Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml b/Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml index 80020539c3bb..5cd512b7d5ba 100644 --- a/Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml +++ b/Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml @@ -51,15 +51,6 @@ properties: appropriate of the LOCHNAGARx_PIN_NUM_GPIOS define, see [3]. maxItems: 1 - pinctrl-0: - description: - A phandle to the default pinctrl state. - - pinctrl-names: - description: - A pinctrl state named "default" must be defined. - const: default - pin-settings: type: object patternProperties: diff --git a/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml b/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml index e50d7ad5c229..c85f759ae5a3 100644 --- a/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml +++ b/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml @@ -30,16 +30,6 @@ description: | Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt properties: - pinctrl-0: - description: - A phandle to the node containing the subnodes containing default - configurations. - - pinctrl-names: - description: - A pinctrl state named "default" must be defined. - const: default - pin-settings: description: One subnode is required to contain the default settings. It diff --git a/Documentation/devicetree/bindings/sound/samsung-i2s.yaml b/Documentation/devicetree/bindings/sound/samsung-i2s.yaml index 2e3628ef48df..84c4d6cba521 100644 --- a/Documentation/devicetree/bindings/sound/samsung-i2s.yaml +++ b/Documentation/devicetree/bindings/sound/samsung-i2s.yaml @@ -110,12 +110,6 @@ properties: Internal DMA register base address of the audio subsystem (used in secondary sound source). - pinctrl-0: - description: Should specify pin control groups used for this controller. - - pinctrl-names: - const: default - power-domains: maxItems: 1 -- 2.32.0

4 4

Re: [PATCH v5] ASoC: adds component driver for TAS575xM digital amplifiers
by Joerg Schambacher 20 Jan '22

20 Jan '22

On Thu, Jan 20, 2022 at 02:18:26AM +0800, kernel test robot wrote: > tree: https://github.com/0day-ci/linux/commits/UPDATE-20220119-210919/Joerg-Scham… > head: 05b8bf5544bc621031f5a0a6bdf1ac6468a7367b > commit: 05b8bf5544bc621031f5a0a6bdf1ac6468a7367b ASoC: adds component driver for TAS575xM digital amplifiers > date: 5 hours ago > config: riscv-randconfig-c006-20220118 (https://download.01.org/0day-ci/archive/20220120/202201200259.nNgbKOJd-lkp@…) > compiler: clang version 14.0.0 (https://github.com/llvm/llvm-project f7b7138a62648f4019c55e4671682af1f851f295) > reproduce (this is a W=1 build): > wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross > chmod +x ~/bin/make.cross > # install riscv cross compiling tool for clang build > # apt-get install binutils-riscv64-linux-gnu > # https://github.com/0day-ci/linux/commit/05b8bf5544bc621031f5a0a6bdf1ac6468a… > git remote add linux-review https://github.com/0day-ci/linux > git fetch --no-tags linux-review UPDATE-20220119-210919/Joerg-Schambacher/ASoC-adds-component-driver-for-TAS575xM-digital-amplifiers/20220110-164852 > git checkout 05b8bf5544bc621031f5a0a6bdf1ac6468a7367b > # save the config file to linux build tree > mkdir build_dir > COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross W=1 O=build_dir ARCH=riscv SHELL=/bin/bash sound/soc/codecs/ > > If you fix the issue, kindly add following tag as appropriate > Reported-by: kernel test robot <lkp(a)intel.com> > > All warnings (new ones prefixed by >>): > > >> sound/soc/codecs/tas5754m.c:246:7: warning: variable 'ret' is used uninitialized whenever switch case is taken [-Wsometimes-uninitialized] > case SND_SOC_BIAS_ON: > ^~~~~~~~~~~~~~~ > sound/soc/codecs/tas5754m.c:267:9: note: uninitialized use occurs here > return ret; > ^~~ > sound/soc/codecs/tas5754m.c:247:7: warning: variable 'ret' is used uninitialized whenever switch case is taken [-Wsometimes-uninitialized] > case SND_SOC_BIAS_PREPARE: > ^~~~~~~~~~~~~~~~~~~~ > sound/soc/codecs/tas5754m.c:267:9: note: uninitialized use occurs here > return ret; > ^~~ > sound/soc/codecs/tas5754m.c:242:9: note: initialize the variable 'ret' to silence this warning > int ret; > ^ > = 0 > 2 warnings generated. > > > vim +/ret +246 sound/soc/codecs/tas5754m.c > > 236 > 237 static int tas5754m_set_bias_level(struct snd_soc_component *component, > 238 enum snd_soc_bias_level level) > 239 { > 240 struct tas5754m_priv *tas5754m = > 241 snd_soc_component_get_drvdata(component); > 242 int ret; > 243 > 244 switch (level) { > 245 default: > > 246 case SND_SOC_BIAS_ON: > 247 case SND_SOC_BIAS_PREPARE: > 248 break; > 249 > 250 case SND_SOC_BIAS_STANDBY: > 251 ret = regmap_update_bits(tas5754m->regmap, > 252 TAS5754M_POWER, TAS5754M_RQST, 0); > 253 if (ret) > 254 dev_err(component->dev, > 255 "Failed to remove standby: %d\n", ret); > 256 break; > 257 > 258 case SND_SOC_BIAS_OFF: > 259 ret = regmap_update_bits(tas5754m->regmap, > 260 TAS5754M_POWER, TAS5754M_RQST, TAS5754M_RQST); > 261 if (ret) > 262 dev_err(component->dev, > 263 "Failed to request standby: %d\n", ret); > 264 break; > 265 } > 266 > 267 return ret; > 268 } > 269 > > --- > 0-DAY CI Kernel Test Service, Intel Corporation > https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org all, fixed. Joerg >From 331a880edff308e8f0608f72f244c25e56162e24 Mon Sep 17 00:00:00 2001 From: Joerg Schambacher <joerg(a)hifiberry.com> Date: Tue, 5 Oct 2021 14:38:21 +0200 Subject: [PATCH] ASoC: adds component driver for TAS575xM digital amplifiers Adds a minimum component driver to run the amplifier in I2S master mode only from standard audio clocks. Therefore, it only allows 44.1, 88.2, 176.4, 48, 96 and 192ksps with 16, 20, 24 and 32 bits sample size. Digital volume control and the -6dB and +0.8dB switches are supported. Signed-off-by: Joerg Schambacher <joerg(a)hifiberry.com> --- sound/soc/codecs/Kconfig | 8 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/tas5754m.c | 691 ++++++++++++++++++++++++++++++++++++ sound/soc/codecs/tas5754m.h | 260 ++++++++++++++ 4 files changed, 961 insertions(+) create mode 100644 sound/soc/codecs/tas5754m.c create mode 100644 sound/soc/codecs/tas5754m.h diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 82ee233a269d..cf0584948fcf 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -210,6 +210,7 @@ config SND_SOC_ALL_CODECS imply SND_SOC_TAS5086 imply SND_SOC_TAS571X imply SND_SOC_TAS5720 + imply SND_SOC_TAS5754M imply SND_SOC_TAS6424 imply SND_SOC_TDA7419 imply SND_SOC_TFA9879 @@ -1419,6 +1420,13 @@ config SND_SOC_TAS5720 Enable support for Texas Instruments TAS5720L/M high-efficiency mono Class-D audio power amplifiers. +config SND_SOC_TAS5754M + tristate "Texas Instruments TAS5754M Digital Input Audio amplifier" + depends on I2C + help + Enable support for Texas Instruments TAS5754M digital input + Class-D audio power amplifiers. + config SND_SOC_TAS6424 tristate "Texas Instruments TAS6424 Quad-Channel Audio amplifier" depends on I2C diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 8dcea2c4604a..39984900258a 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -227,6 +227,7 @@ snd-soc-sti-sas-objs := sti-sas.o snd-soc-tas5086-objs := tas5086.o snd-soc-tas571x-objs := tas571x.o snd-soc-tas5720-objs := tas5720.o +snd-soc-tas5754m-objs := tas5754m.o snd-soc-tas6424-objs := tas6424.o snd-soc-tda7419-objs := tda7419.o snd-soc-tas2770-objs := tas2770.o @@ -555,6 +556,7 @@ obj-$(CONFIG_SND_SOC_TAS2764) += snd-soc-tas2764.o obj-$(CONFIG_SND_SOC_TAS5086) += snd-soc-tas5086.o obj-$(CONFIG_SND_SOC_TAS571X) += snd-soc-tas571x.o obj-$(CONFIG_SND_SOC_TAS5720) += snd-soc-tas5720.o +obj-$(CONFIG_SND_SOC_TAS5754M) += snd-soc-tas5754m.o obj-$(CONFIG_SND_SOC_TAS6424) += snd-soc-tas6424.o obj-$(CONFIG_SND_SOC_TDA7419) += snd-soc-tda7419.o obj-$(CONFIG_SND_SOC_TAS2770) += snd-soc-tas2770.o diff --git a/sound/soc/codecs/tas5754m.c b/sound/soc/codecs/tas5754m.c new file mode 100644 index 000000000000..06c10002f32e --- /dev/null +++ b/sound/soc/codecs/tas5754m.c @@ -0,0 +1,691 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Driver for the TAS5754M Audio Amplifier + * + * Author: Joerg Schambacher <joerg(a)hifiberry.com> + * with fragments from Andy Liu <andy-liu(a)ti.com> + * + * The driver supports I2S master mode only with standard audio + * frequencies 44.1 to 192 ksps from a 24.576/22.2592MHz master + * clock input + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + */ + +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/clk.h> +#include <linux/slab.h> +#include <linux/of.h> +#include <linux/init.h> +#include <linux/i2c.h> +#include <linux/regmap.h> +#include <linux/delay.h> + +#include <sound/tlv.h> +#include <sound/soc.h> +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <sound/initval.h> + +#include "tas5754m.h" + +#define TAS5754M_RATES (SNDRV_PCM_RATE_48000 | \ + SNDRV_PCM_RATE_96000 | \ + SNDRV_PCM_RATE_192000 | \ + SNDRV_PCM_RATE_44100 | \ + SNDRV_PCM_RATE_88200 | \ + SNDRV_PCM_RATE_176400) +#define TAS5754M_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | \ + SNDRV_PCM_FMTBIT_S20_LE | \ + SNDRV_PCM_FMTBIT_S24_LE | \ + SNDRV_PCM_FMTBIT_S32_LE) + + +static const struct reg_default tas5754m_reg_defaults[] = { + { TAS5754M_RESET, 0x00 }, + { TAS5754M_POWER, 0x00 }, + { TAS5754M_MUTE, 0x00 }, + { TAS5754M_DSP, 0x00 }, + { TAS5754M_PLL_REF, 0x00 }, + { TAS5754M_DAC_REF, 0x00 }, + { TAS5754M_DAC_ROUTING, 0x11 }, + { TAS5754M_DSP_PROGRAM, 0x01 }, + { TAS5754M_CLKDET, 0x00 }, + { TAS5754M_AUTO_MUTE, 0x00 }, + { TAS5754M_ERROR_DETECT, 0x00 }, + { TAS5754M_DIGITAL_VOLUME_1, 0x00 }, + { TAS5754M_DIGITAL_VOLUME_2, 0x30 }, + { TAS5754M_DIGITAL_VOLUME_3, 0x30 }, + { TAS5754M_DIGITAL_MUTE_1, 0x22 }, + { TAS5754M_DIGITAL_MUTE_2, 0x00 }, + { TAS5754M_DIGITAL_MUTE_3, 0x07 }, + { TAS5754M_OUTPUT_AMPLITUDE, 0x00 }, + { TAS5754M_ANALOG_GAIN_CTRL, 0x00 }, + { TAS5754M_UNDERVOLTAGE_PROT, 0x00 }, + { TAS5754M_ANALOG_MUTE_CTRL, 0x00 }, + { TAS5754M_ANALOG_GAIN_BOOST, 0x00 }, + { TAS5754M_VCOM_CTRL_1, 0x00 }, + { TAS5754M_VCOM_CTRL_2, 0x01 }, + { TAS5754M_BCLK_LRCLK_CFG, 0x00 }, + { TAS5754M_MASTER_MODE, 0x7c }, + { TAS5754M_GPIO_PLLIN, 0x00 }, + { TAS5754M_SYNCHRONIZE, 0x10 }, + { TAS5754M_PLL_COEFF_P, 0x00 }, + { TAS5754M_PLL_COEFF_J, 0x00 }, + { TAS5754M_PLL_COEFF_DH, 0x00 }, + { TAS5754M_PLL_COEFF_DL, 0x00 }, + { TAS5754M_PLL_COEFF_R, 0x00 }, + { TAS5754M_DSP_CLKDIV, 0x00 }, + { TAS5754M_DAC_CLKDIV, 0x00 }, + { TAS5754M_NCP_CLKDIV, 0x00 }, + { TAS5754M_OSR_CLKDIV, 0x00 }, + { TAS5754M_MASTER_SCLKDIV, 0x00 }, + { TAS5754M_MASTER_LRCLKDIV, 0x00 }, + { TAS5754M_FS_SPEED_MODE, 0x00 }, + { TAS5754M_IDAC_1, 0x01 }, + { TAS5754M_IDAC_2, 0x00 }, +}; + +static bool tas5754m_readable(struct device *dev, unsigned int reg) +{ + switch (reg) { + case TAS5754M_RESET: + case TAS5754M_POWER: + case TAS5754M_MUTE: + case TAS5754M_PLL_EN: + case TAS5754M_DSP: + case TAS5754M_GPIO_EN: + case TAS5754M_BCLK_LRCLK_CFG: + case TAS5754M_DSP_GPIO_INPUT: + case TAS5754M_MASTER_MODE: + case TAS5754M_PLL_REF: + case TAS5754M_DAC_REF: + case TAS5754M_GPIO_PLLIN: + case TAS5754M_SYNCHRONIZE: + case TAS5754M_PLL_COEFF_P: + case TAS5754M_PLL_COEFF_J: + case TAS5754M_PLL_COEFF_DH: + case TAS5754M_PLL_COEFF_DL: + case TAS5754M_PLL_COEFF_R: + case TAS5754M_DSP_CLKDIV: + case TAS5754M_DAC_CLKDIV: + case TAS5754M_NCP_CLKDIV: + case TAS5754M_OSR_CLKDIV: + case TAS5754M_MASTER_SCLKDIV: + case TAS5754M_MASTER_LRCLKDIV: + case TAS5754M_FS_SPEED_MODE: + case TAS5754M_IDAC_1: + case TAS5754M_IDAC_2: + case TAS5754M_ERROR_DETECT: + case TAS5754M_I2S_1: + case TAS5754M_I2S_2: + case TAS5754M_DAC_ROUTING: + case TAS5754M_DSP_PROGRAM: + case TAS5754M_CLKDET: + case TAS5754M_AUTO_MUTE: + case TAS5754M_DIGITAL_VOLUME_1: + case TAS5754M_DIGITAL_VOLUME_2: + case TAS5754M_DIGITAL_VOLUME_3: + case TAS5754M_DIGITAL_MUTE_1: + case TAS5754M_DIGITAL_MUTE_2: + case TAS5754M_DIGITAL_MUTE_3: + case TAS5754M_GPIO_OUTPUT_0: + case TAS5754M_GPIO_OUTPUT_1: + case TAS5754M_GPIO_OUTPUT_2: + case TAS5754M_GPIO_CONTROL_1: + case TAS5754M_GPIO_CONTROL_2: + case TAS5754M_OVERFLOW: + case TAS5754M_RATE_DET_1: + case TAS5754M_RATE_DET_2: + case TAS5754M_RATE_DET_3: + case TAS5754M_RATE_DET_4: + case TAS5754M_CLOCK_STATUS: + case TAS5754M_ANALOG_MUTE_DET: + case TAS5754M_GPIN: + case TAS5754M_DIGITAL_MUTE_DET: + case TAS5754M_OUTPUT_AMPLITUDE: + case TAS5754M_ANALOG_GAIN_CTRL: + case TAS5754M_UNDERVOLTAGE_PROT: + case TAS5754M_ANALOG_MUTE_CTRL: + case TAS5754M_ANALOG_GAIN_BOOST: + case TAS5754M_VCOM_CTRL_1: + case TAS5754M_VCOM_CTRL_2: + case TAS5754M_CRAM_CTRL: + case TAS5754M_FLEX_A: + case TAS5754M_FLEX_B: + return true; + default: + return reg < 0x7f; + } +} + +static bool tas5754m_volatile(struct device *dev, unsigned int reg) +{ + switch (reg) { + case TAS5754M_PLL_EN: + case TAS5754M_OVERFLOW: + case TAS5754M_RATE_DET_1: + case TAS5754M_RATE_DET_2: + case TAS5754M_RATE_DET_3: + case TAS5754M_RATE_DET_4: + case TAS5754M_CLOCK_STATUS: + case TAS5754M_ANALOG_MUTE_DET: + case TAS5754M_GPIN: + case TAS5754M_DIGITAL_MUTE_DET: + case TAS5754M_CRAM_CTRL: + return true; + default: + return reg < 0x7f; + } +} + +struct tas5754m_priv { + struct regmap *regmap; + struct clk *sclk; + int sample_len; + int fmt; + int mode; +}; + +static const struct regmap_range_cfg tas5754m_range = { + .name = "Pages", + .range_min = TAS5754M_VIRT_BASE, + .range_max = TAS5754M_MAX_REGISTER, + .selector_reg = TAS5754M_PAGE, + .selector_mask = 0x7f, + .window_start = 0, + .window_len = 128, +}; + +const struct regmap_config tas5754m_regmap = { + .reg_bits = 8, + .val_bits = 8, + + .ranges = &tas5754m_range, + .num_ranges = 1, + .max_register = TAS5754M_MAX_REGISTER, + + .reg_defaults = tas5754m_reg_defaults, + .num_reg_defaults = ARRAY_SIZE(tas5754m_reg_defaults), + .readable_reg = tas5754m_readable, + .volatile_reg = tas5754m_volatile, + + .cache_type = REGCACHE_RBTREE, +}; + +static const DECLARE_TLV_DB_SCALE(digital_tlv, -10350, 50, 1); +static const DECLARE_TLV_DB_SCALE(analog_tlv, -600, 600, 0); +static const DECLARE_TLV_DB_SCALE(boost_tlv, 0, 80, 0); + +static const struct snd_kcontrol_new tas5754m_controls[] = { +SOC_DOUBLE_R_TLV("Digital Playback Volume", TAS5754M_DIGITAL_VOLUME_2, + TAS5754M_DIGITAL_VOLUME_3, 0, 255, 1, digital_tlv), +SOC_DOUBLE_TLV("Analog Playback Volume", TAS5754M_ANALOG_GAIN_CTRL, + TAS5754M_LAGN_SHIFT, TAS5754M_RAGN_SHIFT, 1, 1, analog_tlv), +SOC_DOUBLE_TLV("Analogue Playback Boost Volume", TAS5754M_ANALOG_GAIN_BOOST, + TAS5754M_AGBL_SHIFT, TAS5754M_AGBR_SHIFT, 1, 0, boost_tlv), +}; + +static int tas5754m_set_bias_level(struct snd_soc_component *component, + enum snd_soc_bias_level level) +{ + struct tas5754m_priv *tas5754m = + snd_soc_component_get_drvdata(component); + int ret = 0; + + switch (level) { + default: + case SND_SOC_BIAS_ON: + case SND_SOC_BIAS_PREPARE: + break; + + case SND_SOC_BIAS_STANDBY: + ret = regmap_update_bits(tas5754m->regmap, + TAS5754M_POWER, TAS5754M_RQST, 0); + if (ret) + dev_err(component->dev, + "Failed to remove standby: %d\n", ret); + break; + + case SND_SOC_BIAS_OFF: + ret = regmap_update_bits(tas5754m->regmap, + TAS5754M_POWER, TAS5754M_RQST, TAS5754M_RQST); + if (ret) + dev_err(component->dev, + "Failed to request standby: %d\n", ret); + break; + } + + return ret; +} + +static int tas5754m_set_clock_tree_master(struct snd_soc_dai *dai, + struct snd_pcm_hw_params *params) +{ + struct snd_soc_component *component = dai->component; + struct tas5754m_priv *tas5754m = + snd_soc_component_get_drvdata(component); + static const struct reg_sequence pll_settings[] = { + { TAS5754M_PLL_COEFF_P, 0x01 }, // P=2 + { TAS5754M_PLL_COEFF_J, 0x08 }, // J=8 + { TAS5754M_PLL_COEFF_DL, 0x00 }, // D12-8 = 0 + { TAS5754M_PLL_COEFF_DH, 0x00 }, // D7-0 = 0 + { TAS5754M_PLL_COEFF_R, 0x00 }, // R=1 + }; + int ret; + + /* disable PLL before any clock tree change */ + ret = regmap_update_bits(tas5754m->regmap, TAS5754M_PLL_EN, + TAS5754M_PLLE, 0); + if (ret) { + dev_err(component->dev, "Failed to disable PLL\n"); + return ret; + } + /* set DAC clock source to MCLK */ + ret = regmap_write(tas5754m->regmap, TAS5754M_DAC_REF, 0x30); + if (ret) { + dev_err(component->dev, "Failed to set DAC ref\n"); + return ret; + } + /* run PLL at fixed ratio to MCLK */ + ret = regmap_multi_reg_write(tas5754m->regmap, pll_settings, + ARRAY_SIZE(pll_settings)); + if (ret) { + dev_err(component->dev, "Failed to set PLL ratio\n"); + return ret; + } + /* set DSP divider to 2 => reg 0x01 */ + ret = regmap_write(tas5754m->regmap, TAS5754M_DSP_CLKDIV, 1); + if (ret) { + dev_err(component->dev, "Failed to set DSP divider\n"); + return ret; + } + /* set DAC divider to 4 => reg 0x03*/ + ret = regmap_write(tas5754m->regmap, TAS5754M_DAC_CLKDIV, 3); + if (ret) { + dev_err(component->dev, "Failed to set OSDACR divider\n"); + return ret; + } + /* set OSR divider to 1 */ + ret = regmap_write(tas5754m->regmap, TAS5754M_OSR_CLKDIV, 0); + if (ret) { + dev_err(component->dev, "Failed to set OSR divider\n"); + return ret; + } + /* set CP divider to 4 => reg 0x03*/ + ret = regmap_write(tas5754m->regmap, TAS5754M_NCP_CLKDIV, 3); + if (ret) { + dev_err(component->dev, "Failed to set CP divider\n"); + return ret; + } + /* finally enable PLL */ + ret = regmap_update_bits(tas5754m->regmap, TAS5754M_PLL_EN, + TAS5754M_PLLE, 1); + if (ret) { + dev_err(component->dev, "Failed to enable PLL\n"); + return ret; + } + + return 0; +} + +static int tas5754m_set_dai_mode(struct snd_soc_dai *dai) +{ + struct snd_soc_component *component = dai->component; + struct tas5754m_priv *tas5754m = + snd_soc_component_get_drvdata(component); + int fmt = tas5754m->fmt; + + /* only I2S MASTER mode implemented */ + if ((fmt & SND_SOC_DAIFMT_FORMAT_MASK) != SND_SOC_DAIFMT_I2S) { + dev_err(component->dev, + "DAI format not supported (I2S master only)\n"); + return -EINVAL; + } + + /* TAS5754/6m do not support inverted clocks in MASTER mode */ + if ((fmt & SND_SOC_DAIFMT_CLOCK_MASK) != SND_SOC_DAIFMT_NB_NF) { + dev_err(component->dev, "Inverted clocks not supported\n"); + return -EINVAL; + } + + switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { + case SND_SOC_DAIFMT_CBM_CFM: + regmap_update_bits(tas5754m->regmap, + TAS5754M_BCLK_LRCLK_CFG, + TAS5754M_LRKO | TAS5754M_BCKO, + TAS5754M_LRKO | TAS5754M_BCKO); + /* reset CLK dividers */ + regmap_update_bits(tas5754m->regmap, + TAS5754M_MASTER_MODE, + 0x00, + TAS5754M_RLRK | TAS5754M_RBCK); + /* ignore all clock error detection but MCLK */ + regmap_update_bits(tas5754m->regmap, + TAS5754M_ERROR_DETECT, + TAS5754M_IPLK | TAS5754M_DCAS | + TAS5754M_IDCM | TAS5754M_IDSK | + TAS5754M_IDBK | TAS5754M_IDFS, + TAS5754M_IPLK | TAS5754M_DCAS | + TAS5754M_IDCM | TAS5754M_IDSK | + TAS5754M_IDBK | TAS5754M_IDFS); + break; + case SND_SOC_DAIFMT_CBS_CFS: + case SND_SOC_DAIFMT_CBM_CFS: + default: + return -EINVAL; + } + + return 0; +} + +static int tas5754m_set_dividers_master(struct snd_soc_dai *dai, + struct snd_pcm_hw_params *params) +{ + struct snd_soc_component *component = dai->component; + struct tas5754m_priv *tas5754m = + snd_soc_component_get_drvdata(component); + unsigned long bclk; + unsigned long mclk; + int bclk_div; + int lrclk_div; + int osr; + int ret; + + /* calculate divider settings based on mclk and sample_len */ + mclk = clk_get_rate(tas5754m->sclk); + bclk = tas5754m->sample_len * 2 * params_rate(params); + bclk_div = mclk / bclk; + lrclk_div = tas5754m->sample_len * 2; + osr = mclk / 4 / params_rate(params) / 16; + + /* stop LR / SCLK clocks */ + ret = regmap_update_bits(tas5754m->regmap, + TAS5754M_MASTER_MODE, 0, + TAS5754M_RLRK | TAS5754M_RBCK); + if (ret) { + dev_err(component->dev, "Failed to stop PLL\n"); + return ret; + } + /* set SCLK divider */ + ret = regmap_write(tas5754m->regmap, TAS5754M_MASTER_SCLKDIV, + bclk_div - 1); + if (ret) { + dev_err(component->dev, "Failed to set SCLK divider\n"); + return ret; + } + /* set LRCLK divider */ + ret = regmap_write(tas5754m->regmap, TAS5754M_MASTER_LRCLKDIV, + lrclk_div - 1); + if (ret) { + dev_err(component->dev, "Failed to set LRCLK divider\n"); + return ret; + } + ret = regmap_write(tas5754m->regmap, + TAS5754M_OSR_CLKDIV, osr - 1); + if (ret) { + dev_err(component->dev, "Failed to set OSR divider\n"); + return ret; + } + /* restart LR / SCLK clocks */ + ret = regmap_update_bits(tas5754m->regmap, + TAS5754M_MASTER_MODE, + TAS5754M_RLRK | TAS5754M_RBCK, + TAS5754M_RLRK | TAS5754M_RBCK); + if (ret) { + dev_err(component->dev, "Failed to restart PLL\n"); + return ret; + } + + return 0; +} + +static int tas5754m_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_component *component = dai->component; + struct tas5754m_priv *tas5754m = + snd_soc_component_get_drvdata(component); + int alen; + int ret; + + switch (params_width(params)) { + case 16: + tas5754m->sample_len = 16; + alen = TAS5754M_ALEN_16; + break; + case 20: + tas5754m->sample_len = 32; + alen = TAS5754M_ALEN_20; + break; + case 24: + tas5754m->sample_len = 32; + alen = TAS5754M_ALEN_24; + break; + case 32: + tas5754m->sample_len = 32; + alen = TAS5754M_ALEN_32; + break; + default: + dev_err(component->dev, "Unsupported sample size: %d\n", + params_width(params)); + return -EINVAL; + } + ret = regmap_update_bits(tas5754m->regmap, TAS5754M_I2S_1, alen, alen); + if (ret) { + dev_err(component->dev, + "Cannot set sample size: %d\n", ret); + return ret; + } + + ret = tas5754m_set_dai_mode(dai); + if (ret) { + dev_err(component->dev, + "DAI mode not supported: %d\n", ret); + return ret; + } + + ret = tas5754m_set_clock_tree_master(dai, params); + if (ret) + return ret; + + switch (params_rate(params)) { + case 44100: + case 48000: + ret = regmap_write(tas5754m->regmap, + TAS5754M_FS_SPEED_MODE, TAS5754M_FSSP_48KHZ); + break; + case 88200: + case 96000: + ret = regmap_write(tas5754m->regmap, + TAS5754M_FS_SPEED_MODE, TAS5754M_FSSP_96KHZ); + break; + case 176400: + case 192000: + ret = regmap_write(tas5754m->regmap, + TAS5754M_FS_SPEED_MODE, TAS5754M_FSSP_192KHZ); + break; + default: + dev_err(component->dev, "Sample rate not supported: %d\n", + params_rate(params)); + return -EINVAL; + } + if (ret) { + dev_err(component->dev, "Failed to config PLL\n"); + return ret; + } + + ret = tas5754m_set_dividers_master(dai, params); + if (ret) + return ret; + + return 0; +} + +static int tas5754m_set_fmt(struct snd_soc_dai *dai, unsigned int fmt) +{ + struct snd_soc_component *component = dai->component; + struct tas5754m_priv *tas5754m = + snd_soc_component_get_drvdata(component); + + tas5754m->fmt = fmt; + + return 0; +} + + +static const struct snd_soc_component_driver tas5754m_soc_component = { + .set_bias_level = tas5754m_set_bias_level, + .idle_bias_on = true, + .controls = tas5754m_controls, + .num_controls = ARRAY_SIZE(tas5754m_controls), +}; + +static int tas5754m_mute(struct snd_soc_dai *dai, int mute, int stream) +{ + struct snd_soc_component *component = dai->component; + + if (mute) { + snd_soc_component_write(component, TAS5754M_MUTE, 0x11); + } else { + /* wait for stable operation before unmute */ + usleep_range(1000, 2000); + snd_soc_component_write(component, TAS5754M_MUTE, 0x00); + } + return 0; +} + +static const struct snd_soc_dai_ops tas5754m_dai_ops = { + .mute_stream = tas5754m_mute, + .hw_params = tas5754m_hw_params, + .set_fmt = tas5754m_set_fmt, +}; + +static struct snd_soc_dai_driver tas5754m_dai = { + .name = "tas5754m-amplifier", + .playback = { + .stream_name = "Playback", + .channels_min = 2, + .channels_max = 2, + .rates = TAS5754M_RATES, + .formats = TAS5754M_FORMATS, + }, + .ops = &tas5754m_dai_ops, +}; + +static int tas5754m_probe(struct device *dev, struct regmap *regmap) +{ + struct tas5754m_priv *tas5754m; + int ret; + + tas5754m = devm_kzalloc(dev, sizeof(struct tas5754m_priv), GFP_KERNEL); + if (!tas5754m) + return -ENOMEM; + + dev_set_drvdata(dev, tas5754m); + tas5754m->regmap = regmap; + + ret = regmap_write(regmap, TAS5754M_RESET, + TAS5754M_RSTR | TAS5754M_RSTM); + if (ret) { + dev_err(dev, "Failed to initialize TAS5754M: %d\n", ret); + goto err; + } + + tas5754m->sclk = devm_clk_get(dev, NULL); + if (PTR_ERR(tas5754m->sclk) == -EPROBE_DEFER) { + ret = -EPROBE_DEFER; + goto err; + } + if (!IS_ERR(tas5754m->sclk)) { + ret = clk_prepare_enable(tas5754m->sclk); + if (ret) { + dev_err(dev, "Failed to enable SCLK: %d\n", ret); + goto err; + } + } + + ret = devm_snd_soc_register_component(dev, + &tas5754m_soc_component, &tas5754m_dai, 1); + if (ret) { + dev_err(dev, "Failed to register CODEC: %d\n", ret); + goto err; + } + + return 0; + +err: + return ret; + +} + +static int tas5754m_i2c_probe(struct i2c_client *i2c, const struct i2c_device_id *id) +{ + struct regmap *regmap; + struct regmap_config config = tas5754m_regmap; + + /* enable auto-increment mode */ + config.read_flag_mask = 0x80; + config.write_flag_mask = 0x80; + + regmap = devm_regmap_init_i2c(i2c, &config); + if (IS_ERR(regmap)) + return PTR_ERR(regmap); + + return tas5754m_probe(&i2c->dev, regmap); +} + +static int tas5754m_remove(struct device *dev) +{ + snd_soc_unregister_component(dev); + + return 0; +} + +static int tas5754m_i2c_remove(struct i2c_client *i2c) +{ + tas5754m_remove(&i2c->dev); + + return 0; +} + +static const struct i2c_device_id tas5754m_i2c_id[] = { + { "tas5754m", }, + { "tas5756m", }, + { } +}; +MODULE_DEVICE_TABLE(i2c, tas5754m_i2c_id); + +#ifdef CONFIG_OF +static const struct of_device_id tas5754m_of_match[] = { + { .compatible = "ti,tas5754m", }, + { .compatible = "ti,tas5756m", }, + { } +}; +MODULE_DEVICE_TABLE(of, tas5754m_of_match); +#endif + +static struct i2c_driver tas5754m_i2c_driver = { + .probe = tas5754m_i2c_probe, + .remove = tas5754m_i2c_remove, + .id_table = tas5754m_i2c_id, + .driver = { + .name = "tas5754m", + .of_match_table = of_match_ptr(tas5754m_of_match), + }, +}; + +module_i2c_driver(tas5754m_i2c_driver); + +MODULE_AUTHOR("Joerg Schambacher <joerg(a)hifiberry.com>"); +MODULE_DESCRIPTION("TAS5754M Audio Amplifier Driver - Master mode only"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/tas5754m.h b/sound/soc/codecs/tas5754m.h new file mode 100644 index 000000000000..c6e26dba169f --- /dev/null +++ b/sound/soc/codecs/tas5754m.h @@ -0,0 +1,260 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * Driver for the TAS575xM DAC+amplifier combo devices + * + * Author: (copied from pcm512x.h) + * Mark Brown <broonie(a)kernel.org> + * Copyright 2014 Linaro Ltd + * + * Register names adapted and non available + * register definitions removed according + + to TAS5754M specification + * Joerg Schambacher <joerg(a)hifiberry.com> + */ + +#ifndef _SND_SOC_TAS5754M +#define _SND_SOC_TAS5754M + +#include <linux/pm.h> +#include <linux/regmap.h> + +#define TAS5754M_VIRT_BASE 0x000 +#define TAS5754M_PAGE_LEN 0x80 +#define TAS5754M_PAGE_BASE(n) (TAS5754M_VIRT_BASE + (TAS5754M_PAGE_LEN * n)) + +#define TAS5754M_PAGE 0 + +#define TAS5754M_RESET (TAS5754M_PAGE_BASE(0) + 1) +#define TAS5754M_POWER (TAS5754M_PAGE_BASE(0) + 2) +#define TAS5754M_MUTE (TAS5754M_PAGE_BASE(0) + 3) +#define TAS5754M_PLL_EN (TAS5754M_PAGE_BASE(0) + 4) +#define TAS5754M_DSP (TAS5754M_PAGE_BASE(0) + 7) +#define TAS5754M_GPIO_EN (TAS5754M_PAGE_BASE(0) + 8) +#define TAS5754M_BCLK_LRCLK_CFG (TAS5754M_PAGE_BASE(0) + 9) +#define TAS5754M_DSP_GPIO_INPUT (TAS5754M_PAGE_BASE(0) + 10) +#define TAS5754M_MASTER_MODE (TAS5754M_PAGE_BASE(0) + 12) +#define TAS5754M_PLL_REF (TAS5754M_PAGE_BASE(0) + 13) +#define TAS5754M_DAC_REF (TAS5754M_PAGE_BASE(0) + 14) +#define TAS5754M_GPIO_PLLIN (TAS5754M_PAGE_BASE(0) + 18) +#define TAS5754M_SYNCHRONIZE (TAS5754M_PAGE_BASE(0) + 19) +#define TAS5754M_PLL_COEFF_P (TAS5754M_PAGE_BASE(0) + 20) +#define TAS5754M_PLL_COEFF_J (TAS5754M_PAGE_BASE(0) + 21) +#define TAS5754M_PLL_COEFF_DH (TAS5754M_PAGE_BASE(0) + 22) +#define TAS5754M_PLL_COEFF_DL (TAS5754M_PAGE_BASE(0) + 23) +#define TAS5754M_PLL_COEFF_R (TAS5754M_PAGE_BASE(0) + 24) +#define TAS5754M_DSP_CLKDIV (TAS5754M_PAGE_BASE(0) + 27) +#define TAS5754M_DAC_CLKDIV (TAS5754M_PAGE_BASE(0) + 28) +#define TAS5754M_NCP_CLKDIV (TAS5754M_PAGE_BASE(0) + 29) +#define TAS5754M_OSR_CLKDIV (TAS5754M_PAGE_BASE(0) + 30) +#define TAS5754M_MASTER_SCLKDIV (TAS5754M_PAGE_BASE(0) + 32) +#define TAS5754M_MASTER_LRCLKDIV (TAS5754M_PAGE_BASE(0) + 33) +#define TAS5754M_FS_SPEED_MODE (TAS5754M_PAGE_BASE(0) + 34) +#define TAS5754M_IDAC_1 (TAS5754M_PAGE_BASE(0) + 35) +#define TAS5754M_IDAC_2 (TAS5754M_PAGE_BASE(0) + 36) +#define TAS5754M_ERROR_DETECT (TAS5754M_PAGE_BASE(0) + 37) +#define TAS5754M_I2S_1 (TAS5754M_PAGE_BASE(0) + 40) +#define TAS5754M_I2S_2 (TAS5754M_PAGE_BASE(0) + 41) +#define TAS5754M_DAC_ROUTING (TAS5754M_PAGE_BASE(0) + 42) +#define TAS5754M_DSP_PROGRAM (TAS5754M_PAGE_BASE(0) + 43) +#define TAS5754M_CLKDET (TAS5754M_PAGE_BASE(0) + 44) +#define TAS5754M_AUTO_MUTE (TAS5754M_PAGE_BASE(0) + 59) +#define TAS5754M_DIGITAL_VOLUME_1 (TAS5754M_PAGE_BASE(0) + 60) +#define TAS5754M_DIGITAL_VOLUME_2 (TAS5754M_PAGE_BASE(0) + 61) +#define TAS5754M_DIGITAL_VOLUME_3 (TAS5754M_PAGE_BASE(0) + 62) +#define TAS5754M_DIGITAL_MUTE_1 (TAS5754M_PAGE_BASE(0) + 63) +#define TAS5754M_DIGITAL_MUTE_2 (TAS5754M_PAGE_BASE(0) + 64) +#define TAS5754M_DIGITAL_MUTE_3 (TAS5754M_PAGE_BASE(0) + 65) +#define TAS5754M_GPIO_OUTPUT_1 (TAS5754M_PAGE_BASE(0) + 82) +#define TAS5754M_GPIO_OUTPUT_0 (TAS5754M_PAGE_BASE(0) + 83) +#define TAS5754M_GPIO_OUTPUT_2 (TAS5754M_PAGE_BASE(0) + 85) +#define TAS5754M_GPIO_CONTROL_1 (TAS5754M_PAGE_BASE(0) + 86) +#define TAS5754M_GPIO_CONTROL_2 (TAS5754M_PAGE_BASE(0) + 87) +#define TAS5754M_OVERFLOW (TAS5754M_PAGE_BASE(0) + 90) +#define TAS5754M_RATE_DET_1 (TAS5754M_PAGE_BASE(0) + 91) +#define TAS5754M_RATE_DET_2 (TAS5754M_PAGE_BASE(0) + 92) +#define TAS5754M_RATE_DET_3 (TAS5754M_PAGE_BASE(0) + 93) +#define TAS5754M_RATE_DET_4 (TAS5754M_PAGE_BASE(0) + 94) +#define TAS5754M_CLOCK_STATUS (TAS5754M_PAGE_BASE(0) + 95) +#define TAS5754M_ANALOG_MUTE_DET (TAS5754M_PAGE_BASE(0) + 108) +#define TAS5754M_FS_MODE_MON (TAS5754M_PAGE_BASE(0) + 115) +#define TAS5754M_GPIN (TAS5754M_PAGE_BASE(0) + 119) +#define TAS5754M_DIGITAL_MUTE_DET (TAS5754M_PAGE_BASE(0) + 120) + +#define TAS5754M_OUTPUT_AMPLITUDE (TAS5754M_PAGE_BASE(1) + 1) +#define TAS5754M_ANALOG_GAIN_CTRL (TAS5754M_PAGE_BASE(1) + 2) +#define TAS5754M_UNDERVOLTAGE_PROT (TAS5754M_PAGE_BASE(1) + 5) +#define TAS5754M_ANALOG_MUTE_CTRL (TAS5754M_PAGE_BASE(1) + 6) +#define TAS5754M_ANALOG_GAIN_BOOST (TAS5754M_PAGE_BASE(1) + 7) +#define TAS5754M_VCOM_CTRL_1 (TAS5754M_PAGE_BASE(1) + 8) +#define TAS5754M_VCOM_CTRL_2 (TAS5754M_PAGE_BASE(1) + 9) + +#define TAS5754M_CRAM_CTRL (TAS5754M_PAGE_BASE(44) + 1) + +#define TAS5754M_FLEX_A (TAS5754M_PAGE_BASE(253) + 63) +#define TAS5754M_FLEX_B (TAS5754M_PAGE_BASE(253) + 64) + +#define TAS5754M_MAX_REGISTER (TAS5754M_PAGE_BASE(253) + 64) + +/* Page 0, Register 1 - reset */ +#define TAS5754M_RSTR (1 << 0) +#define TAS5754M_RSTM (1 << 4) + +/* Page 0, Register 2 - power */ +#define TAS5754M_RQPD (1 << 0) +#define TAS5754M_RQPD_SHIFT 0 +#define TAS5754M_RQST (1 << 4) +#define TAS5754M_RQST_SHIFT 4 + +/* Page 0, Register 3 - mute */ +#define TAS5754M_RQMR (1 << 0) +#define TAS5754M_RQMR_SHIFT 0 +#define TAS5754M_RQML (1 << 4) +#define TAS5754M_RQML_SHIFT 4 + +/* Page 0, Register 4 - PLL */ +#define TAS5754M_PLLE (1 << 0) +#define TAS5754M_PLLE_SHIFT 0 +#define TAS5754M_PLCK (1 << 4) +#define TAS5754M_PLCK_SHIFT 4 + +/* Page 0, Register 7 - DSP */ +#define TAS5754M_SDSL (1 << 0) +#define TAS5754M_SDSL_SHIFT 0 +#define TAS5754M_DEMP (1 << 4) +#define TAS5754M_DEMP_SHIFT 4 + +/* Page 0, Register 8 - GPIO output enable */ +#define TAS5754M_G1OE (1 << 0) +#define TAS5754M_G2OE (1 << 1) +#define TAS5754M_G3OE (1 << 2) +#define TAS5754M_G4OE (1 << 3) +#define TAS5754M_G5OE (1 << 4) +#define TAS5754M_G6OE (1 << 5) + +/* Page 0, Register 9 - BCK, LRCLK configuration */ +#define TAS5754M_LRKO (1 << 0) +#define TAS5754M_LRKO_SHIFT 0 +#define TAS5754M_BCKO (1 << 4) +#define TAS5754M_BCKO_SHIFT 4 +#define TAS5754M_BCKP (1 << 5) +#define TAS5754M_BCKP_SHIFT 5 + +/* Page 0, Register 12 - Master mode BCK, LRCLK reset */ +#define TAS5754M_RLRK (1 << 0) +#define TAS5754M_RLRK_SHIFT 0 +#define TAS5754M_RBCK (1 << 1) +#define TAS5754M_RBCK_SHIFT 1 + +/* Page 0, Register 13 - PLL reference */ +#define TAS5754M_SREF (7 << 4) +#define TAS5754M_SREF_SHIFT 4 +#define TAS5754M_SREF_SCK (0 << 4) +#define TAS5754M_SREF_BCK (1 << 4) +#define TAS5754M_SREF_GPIO (3 << 4) + +/* Page 0, Register 14 - DAC reference */ +#define TAS5754M_SDAC (7 << 4) +#define TAS5754M_SDAC_SHIFT 4 +#define TAS5754M_SDAC_MCK (0 << 4) +#define TAS5754M_SDAC_PLL (1 << 4) +#define TAS5754M_SDAC_SCK (3 << 4) +#define TAS5754M_SDAC_BCK (4 << 4) +#define TAS5754M_SDAC_GPIO (5 << 4) + +/* Page 0, Register 16, 18 - GPIO source for DAC, PLL */ +#define TAS5754M_GREF (7 << 0) +#define TAS5754M_GREF_SHIFT 0 +#define TAS5754M_GREF_GPIO1 (0 << 0) +#define TAS5754M_GREF_GPIO2 (1 << 0) +#define TAS5754M_GREF_GPIO3 (2 << 0) +#define TAS5754M_GREF_GPIO4 (3 << 0) +#define TAS5754M_GREF_GPIO5 (4 << 0) +#define TAS5754M_GREF_GPIO6 (5 << 0) + +/* Page 0, Register 19 - synchronize */ +#define TAS5754M_RQSY (1 << 0) +#define TAS5754M_RQSY_RESUME (0 << 0) +#define TAS5754M_RQSY_HALT (1 << 0) + +/* Page 0, Register 34 - fs speed mode */ +#define TAS5754M_FSSP (3 << 0) +#define TAS5754M_FSSP_SHIFT 0 +#define TAS5754M_FSSP_48KHZ (0 << 0) +#define TAS5754M_FSSP_96KHZ (1 << 0) +#define TAS5754M_FSSP_192KHZ (2 << 0) +#define TAS5754M_FSSP_384KHZ (3 << 0) + +/* Page 0, Register 37 - Error detection */ +#define TAS5754M_IPLK (1 << 0) +#define TAS5754M_DCAS (1 << 1) +#define TAS5754M_IDCM (1 << 2) +#define TAS5754M_IDCH (1 << 3) +#define TAS5754M_IDSK (1 << 4) +#define TAS5754M_IDBK (1 << 5) +#define TAS5754M_IDFS (1 << 6) + +/* Page 0, Register 40 - I2S configuration */ +#define TAS5754M_ALEN (3 << 0) +#define TAS5754M_ALEN_SHIFT 0 +#define TAS5754M_ALEN_16 (0 << 0) +#define TAS5754M_ALEN_20 (1 << 0) +#define TAS5754M_ALEN_24 (2 << 0) +#define TAS5754M_ALEN_32 (3 << 0) +#define TAS5754M_AFMT (3 << 4) +#define TAS5754M_AFMT_SHIFT 4 +#define TAS5754M_AFMT_I2S (0 << 4) +#define TAS5754M_AFMT_DSP (1 << 4) +#define TAS5754M_AFMT_RTJ (2 << 4) +#define TAS5754M_AFMT_LTJ (3 << 4) + +/* Page 0, Register 42 - DAC routing */ +#define TAS5754M_AUPR_SHIFT 0 +#define TAS5754M_AUPL_SHIFT 4 + +/* Page 0, Register 59 - auto mute */ +#define TAS5754M_ATMR_SHIFT 0 +#define TAS5754M_ATML_SHIFT 4 + +/* Page 0, Register 63 - ramp rates */ +#define TAS5754M_VNDF_SHIFT 6 +#define TAS5754M_VNDS_SHIFT 4 +#define TAS5754M_VNUF_SHIFT 2 +#define TAS5754M_VNUS_SHIFT 0 + +/* Page 0, Register 64 - emergency ramp rates */ +#define TAS5754M_VEDF_SHIFT 6 +#define TAS5754M_VEDS_SHIFT 4 + +/* Page 0, Register 65 - Digital mute enables */ +#define TAS5754M_ACTL_SHIFT 2 +#define TAS5754M_AMLE_SHIFT 1 +#define TAS5754M_AMRE_SHIFT 0 + +/* Page 0, Register 80-85, GPIO output selection */ +#define TAS5754M_GxSL (31 << 0) +#define TAS5754M_GxSL_SHIFT 0 +#define TAS5754M_GxSL_OFF (0 << 0) +#define TAS5754M_GxSL_DSP (1 << 0) +#define TAS5754M_GxSL_REG (2 << 0) +#define TAS5754M_GxSL_AMUTB (3 << 0) +#define TAS5754M_GxSL_AMUTL (4 << 0) +#define TAS5754M_GxSL_AMUTR (5 << 0) +#define TAS5754M_GxSL_CLKI (6 << 0) +#define TAS5754M_GxSL_SDOUT (7 << 0) +#define TAS5754M_GxSL_ANMUL (8 << 0) +#define TAS5754M_GxSL_ANMUR (9 << 0) +#define TAS5754M_GxSL_PLLLK (10 << 0) +#define TAS5754M_GxSL_CPCLK (11 << 0) +#define TAS5754M_GxSL_UV0_7 (14 << 0) +#define TAS5754M_GxSL_UV0_3 (15 << 0) +#define TAS5754M_GxSL_PLLCK (16 << 0) + +/* Page 1, Register 2 - analog volume control */ +#define TAS5754M_RAGN_SHIFT 0 +#define TAS5754M_LAGN_SHIFT 4 + +/* Page 1, Register 7 - analog boost control */ +#define TAS5754M_AGBR_SHIFT 0 +#define TAS5754M_AGBL_SHIFT 4 + +#endif -- 2.25.1

1 0

[PATCH] ALSA: hda/cs8409: Add new Warlock SKUs to patch_cs8409
by Vitaly Rodionov 20 Jan '22

20 Jan '22

From: Stefan Binding <sbinding(a)opensource.cirrus.com> Signed-off-by: Stefan Binding <sbinding(a)opensource.cirrus.com> Signed-off-by: Vitaly Rodionov <vitalyr(a)opensource.cirrus.com> --- sound/pci/hda/patch_cs8409-tables.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/sound/pci/hda/patch_cs8409-tables.c b/sound/pci/hda/patch_cs8409-tables.c index df0b4522babf..2d1fa706327b 100644 --- a/sound/pci/hda/patch_cs8409-tables.c +++ b/sound/pci/hda/patch_cs8409-tables.c @@ -490,6 +490,8 @@ const struct snd_pci_quirk cs8409_fixup_tbl[] = { SND_PCI_QUIRK(0x1028, 0x0ADC, "Warlock", CS8409_WARLOCK), SND_PCI_QUIRK(0x1028, 0x0AF4, "Warlock", CS8409_WARLOCK), SND_PCI_QUIRK(0x1028, 0x0AF5, "Warlock", CS8409_WARLOCK), + SND_PCI_QUIRK(0x1028, 0x0BB5, "Warlock N3 15 TGL-U Nuvoton EC", CS8409_WARLOCK), + SND_PCI_QUIRK(0x1028, 0x0BB6, "Warlock V3 15 TGL-U Nuvoton EC", CS8409_WARLOCK), SND_PCI_QUIRK(0x1028, 0x0A77, "Cyborg", CS8409_CYBORG), SND_PCI_QUIRK(0x1028, 0x0A78, "Cyborg", CS8409_CYBORG), SND_PCI_QUIRK(0x1028, 0x0A79, "Cyborg", CS8409_CYBORG), -- 2.25.1

2 1

Make code compatible with Python 3.10
by GitHub pull_request - opened 20 Jan '22

20 Jan '22

alsa-project/alsa-lib pull request #210 was opened from ginggs: As noted in bpo-30459, PyTuple_SET_ITEM() does not return a value. https://bugs.python.org/issue30459 Request URL : https://github.com/alsa-project/alsa-lib/pull/210 Patch URL : https://github.com/alsa-project/alsa-lib/pull/210.patch Repository URL: https://github.com/alsa-project/alsa-lib

1 0

alsamixer: `color` settings are not respected anymore
by GitHub issues - opened 20 Jan '22

20 Jan '22

alsa-project/alsa-utils issue #137 was opened from int-e: `alsamixer` supports customizing colors for the various controls using the `color` directive in the configuration file. Commit https://github.com/alsa-project/alsa-utils/commit/5d4442b2cfe967c44b5cd74fc… broke this feature, because it initializes curses colors *after* reading the configuration file, which overrides any colors that the configuration file may have set. Issue URL : https://github.com/alsa-project/alsa-utils/issues/137 Repository URL: https://github.com/alsa-project/alsa-utils

1 0