- Alsa-devel - mailman.alsa-project.org

Re: [alsa-devel] Intel G45 no sound without monitor
by Wu Fengguang 17 Feb '09

17 Feb '09

On Mon, Feb 16, 2009 at 11:07:02PM +0200, Shane W wrote: > Hello, > > Not sure if this is a board hardware issue or something > driver specific but thought I'd put it out there in case it > wasn't known. On my G45, I don't get any sound if my > television isn't turned on or is disconnected. That is, > HDMI from the G45 to the Yamaha amp is a no go without a > connected monitor. Turning on the monitor after system > boot has no effect so monitor must be turned on and system > rebooted for sound to work. Hi Shane, It's related to our intel gfx driver. We bought the same Yamaha RX-V1800 and experienced the same problem. I was doing extensive (black box) debugging on it these days, and found that the following process can produce sound on Yamaha: startx xrandr --output HDMI-1 --mode 1920x1200 In fact the default 1920x540 mode is the only mode in which Yamaha cannot produce sound. Our intel gfx maintainer confirmed that it's actually the 1080i mode that is not supported yet. Thanks, Fengguang

2 1

[alsa-devel] dma buffer format
by York Sun 16 Feb '09

16 Feb '09

Takashi, I am now working on a surround sound driver for the first time. I am confused by the packed format of dma buffer. If the channel number is 6, is the buffer filled with data as front left, front right, rear left, rear right, center, LFE or front left, rear left, center, front right, rear left, LFE? Thanks, York

2 3

[alsa-devel] [PATCH] cs4236: cs4232 and cs4236 driver merge to solve PnP BIOS detection
by Krzysztof Helt 16 Feb '09

16 Feb '09

From: Krzysztof Helt <krzysztof.h1(a)wp.pl> Also, the patch adds recognition if the chip is cs4236b+ or earlier part. This unifies drivers for both cs4232 and cs4236+ chips. It allows to use the PnP BIOS detection for the cs4236+ chips. Previously, only the snd-cs4232 could be detected by the PnP BIOS. The cs4232+ cards reports two separate PnP BIOS ids. The patch adds search for the second id to find out resources assigned to a control port. Signed-off-by: Krzysztof Helt <krzysztof.h1(a)wp.pl> --- The cs4232 and cs4236 are the same now and one can be removed. Stanley tested this patch and it worked for him (cs4232 chip in Tecra 500). I have tested it on Dell Latitude CP (cs4237b chip) which is now correctly recognized. Previously, it was recognized as a basic cs4236 chip. Also, I have tested it with Maxi Sound 32 PnP card (ISA PnP cs4236b) with success. A side effect of this approach is that on ISA PnP cards the driver reports an error of PnP BIOS detection everytime it is loaded. This is due to driver rejecting the PnP BIOS initialization for ISA PnP cards. Probably, the earlier cs4232 driver worked the same way. diff --git a/include/sound/wss.h b/include/sound/wss.h index fd01f22..6d65f32 100644 --- a/include/sound/wss.h +++ b/include/sound/wss.h @@ -154,6 +154,7 @@ int snd_wss_create(struct snd_card *card, unsigned short hardware, unsigned short hwshare, struct snd_wss **rchip); +int snd_wss_free(struct snd_wss *chip); int snd_wss_pcm(struct snd_wss *chip, int device, struct snd_pcm **rpcm); int snd_wss_timer(struct snd_wss *chip, int device, struct snd_timer **rtimer); int snd_wss_mixer(struct snd_wss *chip); diff --git a/sound/isa/cs423x/Makefile b/sound/isa/cs423x/Makefile index 5870ca2..dfdd96d 100644 --- a/sound/isa/cs423x/Makefile +++ b/sound/isa/cs423x/Makefile @@ -10,6 +10,6 @@ snd-cs4236-objs := cs4236.o # Toplevel Module Dependency obj-$(CONFIG_SND_CS4231) += snd-cs4231.o -obj-$(CONFIG_SND_CS4232) += snd-cs4232.o +obj-$(CONFIG_SND_CS4232) += snd-cs4232.o snd-cs4236-lib.o obj-$(CONFIG_SND_CS4236) += snd-cs4236.o snd-cs4236-lib.o diff --git a/sound/isa/cs423x/cs4236.c b/sound/isa/cs423x/cs4236.c index f784598..089b7e8 100644 --- a/sound/isa/cs423x/cs4236.c +++ b/sound/isa/cs423x/cs4236.c @@ -33,17 +33,14 @@ MODULE_AUTHOR("Jaroslav Kysela <perex(a)perex.cz>"); MODULE_LICENSE("GPL"); -#ifdef CS4232 -MODULE_DESCRIPTION("Cirrus Logic CS4232"); +MODULE_DESCRIPTION("Cirrus Logic CS4232-9"); MODULE_SUPPORTED_DEVICE("{{Turtle Beach,TBS-2000}," "{Turtle Beach,Tropez Plus}," "{SIC CrystalWave 32}," "{Hewlett Packard,Omnibook 5500}," "{TerraTec,Maestro 32/96}," - "{Philips,PCA70PS}}"); -#else -MODULE_DESCRIPTION("Cirrus Logic CS4235-9"); -MODULE_SUPPORTED_DEVICE("{{Crystal Semiconductors,CS4235}," + "{Philips,PCA70PS}}," + "{{Crystal Semiconductors,CS4235}," "{Crystal Semiconductors,CS4236}," "{Crystal Semiconductors,CS4237}," "{Crystal Semiconductors,CS4238}," @@ -70,15 +67,9 @@ MODULE_SUPPORTED_DEVICE("{{Crystal Semiconductors,CS4235}," "{Typhoon Soundsystem,CS4236B}," "{Turtle Beach,Malibu}," "{Unknown,Digital PC 5000 Onboard}}"); -#endif -#ifdef CS4232 -#define IDENT "CS4232" -#define DEV_NAME "cs4232" -#else -#define IDENT "CS4236+" -#define DEV_NAME "cs4236" -#endif +#define IDENT "CS4232+" +#define DEV_NAME "cs4232+" static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX; /* Index 0-MAX */ static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR; /* ID for this card */ @@ -128,9 +119,7 @@ MODULE_PARM_DESC(dma2, "DMA2 # for " IDENT " driver."); #ifdef CONFIG_PNP static int isa_registered; static int pnpc_registered; -#ifdef CS4232 static int pnp_registered; -#endif #endif /* CONFIG_PNP */ struct snd_card_cs4236 { @@ -145,11 +134,10 @@ struct snd_card_cs4236 { #ifdef CONFIG_PNP -#ifdef CS4232 /* * PNP BIOS */ -static const struct pnp_device_id snd_cs4232_pnpbiosids[] = { +static const struct pnp_device_id snd_cs423x_pnpbiosids[] = { { .id = "CSC0100" }, { .id = "CSC0000" }, /* Guillemot Turtlebeach something appears to be cs4232 compatible @@ -157,10 +145,8 @@ static const struct pnp_device_id snd_cs4232_pnpbiosids[] = { { .id = "GIM0100" }, { .id = "" } }; -MODULE_DEVICE_TABLE(pnp, snd_cs4232_pnpbiosids); -#endif /* CS4232 */ +MODULE_DEVICE_TABLE(pnp, snd_cs423x_pnpbiosids); -#ifdef CS4232 #define CS423X_ISAPNP_DRIVER "cs4232_isapnp" static struct pnp_card_device_id snd_cs423x_pnpids[] = { /* Philips PCA70PS */ @@ -179,12 +165,6 @@ static struct pnp_card_device_id snd_cs423x_pnpids[] = { { .id = "CSCf032", .devs = { { "CSC0000" }, { "CSC0010" }, { "CSC0003" } } }, /* Netfinity 3000 on-board soundcard */ { .id = "CSCe825", .devs = { { "CSC0100" }, { "CSC0110" }, { "CSC010f" } } }, - /* --- */ - { .id = "" } /* end */ -}; -#else /* CS4236 */ -#define CS423X_ISAPNP_DRIVER "cs4236_isapnp" -static struct pnp_card_device_id snd_cs423x_pnpids[] = { /* Intel Marlin Spike Motherboard - CS4235 */ { .id = "CSC0225", .devs = { { "CSC0000" }, { "CSC0010" }, { "CSC0003" } } }, /* Intel Marlin Spike Motherboard (#2) - CS4235 */ @@ -266,7 +246,6 @@ static struct pnp_card_device_id snd_cs423x_pnpids[] = { /* --- */ { .id = "" } /* end */ }; -#endif MODULE_DEVICE_TABLE(pnp_card, snd_cs423x_pnpids); @@ -323,17 +302,19 @@ static int __devinit snd_cs423x_pnp_init_mpu(int dev, struct pnp_dev *pdev) return 0; } -#ifdef CS4232 -static int __devinit snd_card_cs4232_pnp(int dev, struct snd_card_cs4236 *acard, - struct pnp_dev *pdev) +static int __devinit snd_card_cs423x_pnp(int dev, struct snd_card_cs4236 *acard, + struct pnp_dev *pdev, + struct pnp_dev *cdev) { acard->wss = pdev; if (snd_cs423x_pnp_init_wss(dev, acard->wss) < 0) return -EBUSY; - cport[dev] = -1; + if (cdev) + cport[dev] = pnp_port_start(cdev, 0); + else + cport[dev] = -1; return 0; } -#endif static int __devinit snd_card_cs423x_pnpc(int dev, struct snd_card_cs4236 *acard, struct pnp_card_link *card, @@ -411,40 +392,39 @@ static int __devinit snd_cs423x_probe(struct snd_card *card, int dev) return -EBUSY; } -#ifdef CS4232 err = snd_wss_create(card, port[dev], cport[dev], irq[dev], dma1[dev], dma2[dev], - WSS_HW_DETECT, 0, &chip); - if (err < 0) - return err; - acard->chip = chip; - - err = snd_wss_pcm(chip, 0, &pcm); - if (err < 0) - return err; - - err = snd_wss_mixer(chip); + WSS_HW_DETECT3, 0, &chip); if (err < 0) return err; - -#else /* CS4236 */ - err = snd_cs4236_create(card, - port[dev], cport[dev], - irq[dev], dma1[dev], dma2[dev], - WSS_HW_DETECT, 0, &chip); - if (err < 0) - return err; - acard->chip = chip; - - err = snd_cs4236_pcm(chip, 0, &pcm); - if (err < 0) - return err; - - err = snd_cs4236_mixer(chip); - if (err < 0) - return err; -#endif + if (chip->hardware & WSS_HW_CS4236B_MASK) { + snd_wss_free(chip); + err = snd_cs4236_create(card, + port[dev], cport[dev], + irq[dev], dma1[dev], dma2[dev], + WSS_HW_DETECT, 0, &chip); + if (err < 0) + return err; + acard->chip = chip; + + err = snd_cs4236_pcm(chip, 0, &pcm); + if (err < 0) + return err; + + err = snd_cs4236_mixer(chip); + if (err < 0) + return err; + } else { + acard->chip = chip; + err = snd_wss_pcm(chip, 0, &pcm); + if (err < 0) + return err; + + err = snd_wss_mixer(chip); + if (err < 0) + return err; + } strcpy(card->driver, pcm->name); strcpy(card->shortname, pcm->name); sprintf(card->longname, "%s at 0x%lx, irq %i, dma %i", @@ -579,13 +559,15 @@ static struct isa_driver cs423x_isa_driver = { #ifdef CONFIG_PNP -#ifdef CS4232 -static int __devinit snd_cs4232_pnpbios_detect(struct pnp_dev *pdev, +static int __devinit snd_cs423x_pnpbios_detect(struct pnp_dev *pdev, const struct pnp_device_id *id) { static int dev; int err; struct snd_card *card; + struct pnp_dev *cdev; + struct list_head *pos; + char cid[PNP_ID_LEN]; if (pnp_device_is_isapnp(pdev)) return -ENOENT; /* we have another procedure - card */ @@ -596,10 +578,20 @@ static int __devinit snd_cs4232_pnpbios_detect(struct pnp_dev *pdev, if (dev >= SNDRV_CARDS) return -ENODEV; + /* prepare second id */ + strcpy(cid, pdev->id[0].id); + cid[5] = '1'; + cdev = NULL; + list_for_each(pos, &(pdev->protocol->devices)) { + cdev = list_entry(pos, struct pnp_dev, protocol_list); + if (!strcmp(cdev->id[0].id, cid)) + break; + } err = snd_cs423x_card_new(dev, &card); if (err < 0) return err; - if ((err = snd_card_cs4232_pnp(dev, card->private_data, pdev)) < 0) { + err = snd_card_cs423x_pnp(dev, card->private_data, pdev, cdev); + if (err < 0) { printk(KERN_ERR "PnP BIOS detection failed for " IDENT "\n"); snd_card_free(card); return err; @@ -614,35 +606,34 @@ static int __devinit snd_cs4232_pnpbios_detect(struct pnp_dev *pdev, return 0; } -static void __devexit snd_cs4232_pnp_remove(struct pnp_dev * pdev) +static void __devexit snd_cs423x_pnp_remove(struct pnp_dev *pdev) { snd_card_free(pnp_get_drvdata(pdev)); pnp_set_drvdata(pdev, NULL); } #ifdef CONFIG_PM -static int snd_cs4232_pnp_suspend(struct pnp_dev *pdev, pm_message_t state) +static int snd_cs423x_pnp_suspend(struct pnp_dev *pdev, pm_message_t state) { return snd_cs423x_suspend(pnp_get_drvdata(pdev)); } -static int snd_cs4232_pnp_resume(struct pnp_dev *pdev) +static int snd_cs423x_pnp_resume(struct pnp_dev *pdev) { return snd_cs423x_resume(pnp_get_drvdata(pdev)); } #endif -static struct pnp_driver cs4232_pnp_driver = { - .name = "cs4232-pnpbios", - .id_table = snd_cs4232_pnpbiosids, - .probe = snd_cs4232_pnpbios_detect, - .remove = __devexit_p(snd_cs4232_pnp_remove), +static struct pnp_driver cs423x_pnp_driver = { + .name = "cs423x-pnpbios", + .id_table = snd_cs423x_pnpbiosids, + .probe = snd_cs423x_pnpbios_detect, + .remove = __devexit_p(snd_cs423x_pnp_remove), #ifdef CONFIG_PM - .suspend = snd_cs4232_pnp_suspend, - .resume = snd_cs4232_pnp_resume, + .suspend = snd_cs423x_pnp_suspend, + .resume = snd_cs423x_pnp_resume, #endif }; -#endif /* CS4232 */ static int __devinit snd_cs423x_pnpc_detect(struct pnp_card_link *pcard, const struct pnp_card_device_id *pid) @@ -716,18 +707,14 @@ static int __init alsa_card_cs423x_init(void) #ifdef CONFIG_PNP if (!err) isa_registered = 1; -#ifdef CS4232 - err = pnp_register_driver(&cs4232_pnp_driver); + err = pnp_register_driver(&cs423x_pnp_driver); if (!err) pnp_registered = 1; -#endif err = pnp_register_card_driver(&cs423x_pnpc_driver); if (!err) pnpc_registered = 1; -#ifdef CS4232 if (pnp_registered) err = 0; -#endif if (isa_registered) err = 0; #endif @@ -739,10 +726,8 @@ static void __exit alsa_card_cs423x_exit(void) #ifdef CONFIG_PNP if (pnpc_registered) pnp_unregister_card_driver(&cs423x_pnpc_driver); -#ifdef CS4232 if (pnp_registered) - pnp_unregister_driver(&cs4232_pnp_driver); -#endif + pnp_unregister_driver(&cs423x_pnp_driver); if (isa_registered) #endif isa_unregister_driver(&cs423x_isa_driver); diff --git a/sound/isa/wss/wss_lib.c b/sound/isa/wss/wss_lib.c index aab44e7..5d2ba1b 100644 --- a/sound/isa/wss/wss_lib.c +++ b/sound/isa/wss/wss_lib.c @@ -1682,7 +1682,7 @@ static void snd_wss_resume(struct snd_wss *chip) } #endif /* CONFIG_PM */ -static int snd_wss_free(struct snd_wss *chip) +int snd_wss_free(struct snd_wss *chip) { release_and_free_resource(chip->res_port); release_and_free_resource(chip->res_cport); @@ -1705,6 +1705,7 @@ static int snd_wss_free(struct snd_wss *chip) kfree(chip); return 0; } +EXPORT_SYMBOL(snd_wss_free); static int snd_wss_dev_free(struct snd_device *device) { ---------------------------------------------------------------------- Zostan mistrzem parkowania w Bombaju! Zagraj >> http://link.interia.pl/f204e

2 5

[alsa-devel] [PATCH] Workaround for misdetected sample rate with CM6207
by Joris van Rantwijk 16 Feb '09

16 Feb '09

Summary: Workaround for misdetected sample rate with CM6207 The CM6207 incorrectly advertises its 96 kHz playback setting as 48 kHz in its USB device descriptor. This patch extends an existing workaround in usbaudio.c to also cover the CM6207. This resolves issue 0004249 in the ALSA bug tracker. Signed-off by: Joris van Rantwijk <jorispubl(a)xs4all.nl> diff -ur linux-2.6.28.4/sound/usb/usbaudio.c linux-2.6.28.4_j/sound/usb/usbaudio.c --- linux-2.6.28.4/sound/usb/usbaudio.c 2009-02-13 21:45:17.000000000 +0100 +++ linux-2.6.28.4_j/sound/usb/usbaudio.c 2009-02-13 22:00:44.000000000 +0100 @@ -2533,19 +2533,20 @@ } fp->nr_rates = nr_rates; - fp->rate_min = fp->rate_max = combine_triple(&fmt[8]); + fp->rate_min = fp->rate_max = 0; for (r = 0, idx = offset + 1; r < nr_rates; r++, idx += 3) { unsigned int rate = combine_triple(&fmt[idx]); /* C-Media CM6501 mislabels its 96 kHz altsetting */ if (rate == 48000 && nr_rates == 1 && - chip->usb_id == USB_ID(0x0d8c, 0x0201) && + (chip->usb_id == USB_ID(0x0d8c, 0x0201) || + chip->usb_id == USB_ID(0x0d8c, 0x0102)) && fp->altsetting == 5 && fp->maxpacksize == 392) rate = 96000; fp->rate_table[r] = rate; nonzero_rates |= rate; - if (rate < fp->rate_min) + if (r == 0 || rate < fp->rate_min) fp->rate_min = rate; - else if (rate > fp->rate_max) + else if (r == 0 || rate > fp->rate_max) fp->rate_max = rate; fp->rates |= snd_pcm_rate_to_rate_bit(rate); }

2 3

[alsa-devel] ALSA layer in Linux 2.6.18 and OSS
by Viral Mehta 16 Feb '09

16 Feb '09

Hi All, I am trying to make an application that does Audio playback and record. I have configured Kernel and Re-built it. I want to use only ALSA features. I have said "Yes" to all ALSA related options and "No" to all OSS related things. When I booted my kernel, I found that there was no "/dev/dsp" device and so my application was not able to run. The application opens "/dev/dsp" device first and then does other things. Next time, when I enabled few of the OSS options in kernel's config file. I was able to run my application. My question is I do not want OSS at all. I just need ALSA then in that case what I am doing wrong. Thanks, Viral -- _____________________________________________________________________ Disclaimer: This e-mail message and all attachments transmitted with it are intended solely for the use of the addressee and may contain legally privileged and confidential information. If the reader of this message is not the intended recipient, or an employee or agent responsible for delivering this message to the intended recipient, you are hereby notified that any dissemination, distribution, copying, or other use of this message or its attachments is strictly prohibited. If you have received this message in error, please notify the sender immediately by replying to this message and please delete it from your computer. Any views expressed in this message are those of the individual sender unless otherwise stated.Company has taken enough precautions to prevent the spread of viruses. However the company accepts no liability for any damage caused by any virus transmitted by this email. __________________________________________________________________________

4 6

[alsa-devel] Possible bug with ICE1712 driver
by Brendan Minish 16 Feb '09

16 Feb '09

Hello the driver for my M-Audio Delta66, snd_ice1712 fails when my machine resumes from suspend. I get no audio out and software accessing the the audio device appears to either hang or work normally (but with no output) I can always get sound working again by removing and reinserting the kernel module snd_ice1712 after the machine resumes if the ice1712 driver is compiled into the kernel then sound fails after resume and there appears to be no way to get it working again Platform Linux Intel x86_64 (core 2 E6700 ) Distro Fedora Custom kernel ver 2.6.27.12 issue also observed on distro kernel -2.6.27.12-170.2.5.fc10.x86_64 Attached dmesg output for suspend, resume and reprobing of snd_ice1712 Attached lspci output Attached lsmod output Anything else I should capture to help debug this ? Is this the right place to file this ? thanks for the help regards Brendan Minish

2 2

[alsa-devel] how to set default alsa pcm device as bluetooth, so i can play flash in firefox to bluetooth headset?
by Ted T. Logan 16 Feb '09

16 Feb '09

I did this, but no go: pcm.bluetoothstereo { type bluetooth device 00:18:E4:0C:4D:17 #headset profile "auto" } pcm.!default { type plug slave.pcm "bluetoothstereo" } I can do things like mplayer -ao alsa:device=bluetoothstereo with no problem, and I hear fine through the headset. However, I'd like to be able to play flash audio from firefox through the headset. What am i doing wrong? rpmq bluez bluez-hcidump-1.42-2.fc10.i386 bluez-libs-4.22-2.fc10.i386 bluez-4.22-2.fc10.i386 bluez-gstreamer-4.22-2.fc10.i386 bluez-gnome-analyzer-1.8-11.fc10.i386 bluez-libs-devel-4.22-2.fc10.i386 bluez-gnome-1.8-11.fc10.i386 bluez-alsa-4.22-2.fc10.i386 bluez-cups-4.22-2.fc10.i386

1 0

[alsa-devel] [PATCH] staging: &&/|| typo
by Roel Kluin 16 Feb '09

16 Feb '09

&&/|| typo Signed-off-by: Roel Kluin <roel.kluin(a)gmail.com> --- // vi sound/oss/ad1848.c +83 #define MD_1845 4 ... #define MD_1845_SSCAPE 9 /* Ensoniq Soundscape PNP*/ diff --git a/sound/oss/ad1848.c b/sound/oss/ad1848.c index 7cf9913..a5b8356 100644 --- a/sound/oss/ad1848.c +++ b/sound/oss/ad1848.c @@ -2107,7 +2107,7 @@ int ad1848_control(int cmd, int arg) switch (cmd) { case AD1848_SET_XTAL: /* Change clock frequency of AD1845 (only ) */ - if (devc->model != MD_1845 || devc->model != MD_1845_SSCAPE) + if (devc->model != MD_1845 && devc->model != MD_1845_SSCAPE) return -EINVAL; spin_lock_irqsave(&devc->lock,flags); ad_enter_MCE(devc);

2 1

[alsa-devel] Bug: Mic problem, mostly noise, almost no signal, AD1988B on an Asus P5B
by Thomas Stenhaug 16 Feb '09

16 Feb '09

Current settings and info here: http://www.alsa-project.org/db/?f=021ee315857ae0928de665f1f0924cc84c609576 When I record with these settings, I get a /lot/ of static, and discernible signal when I tap the microphone on my desktop, or scream into it. The static gets better when I reduce the capture level, but the signal is still barely discernible. The microphone works in the same jack when the computer is running Windows. I've also tried a different mic, with the same results. Playback works flawlessly. I have seen some posts with people having problems that sound similar, and some of them seems to be resolved by enabling Mic bias. However, I don't have a control called that when I look at alsamixer. My system is running Debian Etch. When I started working on this problem, I used the packages from the "testing" (Etch) repository. I then pulled in alsa-base and alsa-utils from the "experimental" repository, and compiled the 1.0.18a drivers. This changed nothing in the recordings, nor did any new controls appear in alsamixer. I added "snd-hda-intel: model=6stack-dig" to /etc/modprobe.db/alsa-base, and there was no change in the visible controls. Regards, Thomas

1 0

[alsa-devel] ctxfi/pulse audio problems and skype - only hear digital noise after a while in call
by Ted T. Logan 15 Feb '09

15 Feb '09

Help, I have x-fi live, using ctxfi driver. I had to start using pulse audio because after a recent alsa upgrade, no matter what I did, my creative x-fi would no longer show as default sound card, but was way down the list, no matter what I did. Anyway, my current problem is I use skype all the time, but after I am in a phone call for a while, when the other person talks, I just hear digital noise/garbage whenever they talk, so I have to hang up. It is causing me a lot of grief because I use skype for business. I am not telling skype to use pulseaudio even though the rest of my apps are, because it doesn't seem to work well with skype, so I just have it use alsa/ctxfi. I don't know what to do, I didn't have this problem a few months ago, and I'm not sure if it's: 1.Since I upgraded from f9 to f10 2.Since I started using pulseaudio 3.Since I switched from sbxfi driver to ctxfi My current system is f10 rpmq alsa alsa-oss-1.0.17-1.fc10.i386 alsa-oss-libs-1.0.17-1.fc10.i386 alsa-utils-1.0.19-1.fc10.i386 alsa-plugins-pulseaudio-1.0.18-2.fc10.i386 alsa-lib-1.0.19-2.fc10.i386 alsa-lib-devel-1.0.19-2.fc10.i386 alsa-tools-1.0.17-1.fc10.i386 bluez-alsa-4.22-2.fc10.i386 alsa-plugins-oss-1.0.18-2.fc10.i386 Thanks in advance!

1 0