- Alsa-devel - mailman.alsa-project.org

[PATCH v26 00/33] Introduce QC USB SND audio offloading support
by Wesley Cheng 04 Sep '24

04 Sep '24

Requesting to see if we can get some Acked-By tags, and merge on usb-next. Several Qualcomm based chipsets can support USB audio offloading to a dedicated audio DSP, which can take over issuing transfers to the USB host controller. The intention is to reduce the load on the main processors in the SoC, and allow them to be placed into lower power modes. There are several parts to this design: 1. Adding ASoC binding layer 2. Create a USB backend for Q6DSP 3. Introduce XHCI interrupter support 4. Create vendor ops for the USB SND driver USB | ASoC -------------------------------------------------------------------- | _________________________ | |sm8250 platform card | | |_________________________| | | | | ___V____ ____V____ | |Q6USB | |Q6AFE | | |"codec" | |"cpu" | | |________| |_________| | ^ ^ ^ | | |________| | ___V____ | | |SOC-USB | | ________ ________ | | | |USB SND |<--->|QC offld|<------------>|________| | |(card.c)| | |<---------- | |________| |________|___ | | | ^ ^ | | | ____________V_________ | | | | | |APR/GLINK | __ V_______________V_____ | | | |______________________| |USB SND (endpoint.c) | | | | ^ |_________________________| | | | | ^ | | | ___________V___________ | | | |->|audio DSP | ___________V_____________ | | |_______________________| |XHCI HCD |<- | |_________________________| | Adding ASoC binding layer ========================= soc-usb: Intention is to treat a USB port similar to a headphone jack. The port is always present on the device, but cable/pin status can be enabled/disabled. Expose mechanisms for USB backend ASoC drivers to communicate with USB SND. Create a USB backend for Q6DSP ============================== q6usb: Basic backend driver that will be responsible for maintaining the resources needed to initiate a playback stream using the Q6DSP. Will be the entity that checks to make sure the connected USB audio device supports the requested PCM format. If it does not, the PCM open call will fail, and userspace ALSA can take action accordingly. Introduce XHCI interrupter support ================================== XHCI HCD supports multiple interrupters, which allows for events to be routed to different event rings. This is determined by "Interrupter Target" field specified in Section "6.4.1.1 Normal TRB" of the XHCI specification. Events in the offloading case will be routed to an event ring that is assigned to the audio DSP. Create vendor ops for the USB SND driver ======================================== qc_audio_offload: This particular driver has several components associated with it: - QMI stream request handler - XHCI interrupter and resource management - audio DSP memory management When the audio DSP wants to enable a playback stream, the request is first received by the ASoC platform sound card. Depending on the selected route, ASoC will bring up the individual DAIs in the path. The Q6USB backend DAI will send an AFE port start command (with enabling the USB playback path), and the audio DSP will handle the request accordingly. Part of the AFE USB port start handling will have an exchange of control messages using the QMI protocol. The qc_audio_offload driver will populate the buffer information: - Event ring base address - EP transfer ring base address and pass it along to the audio DSP. All endpoint management will now be handed over to the DSP, and the main processor is not involved in transfers. Overall, implementing this feature will still expose separate sound card and PCM devices for both the platform card and USB audio device: 0 [SM8250MTPWCD938]: sm8250 - SM8250-MTP-WCD9380-WSA8810-VA-D SM8250-MTP-WCD9380-WSA8810-VA-DMIC 1 [Audio ]: USB-Audio - USB Audio Generic USB Audio at usb-xhci-hcd.1.auto-1.4, high speed This is to ensure that userspace ALSA entities can decide which route to take when executing the audio playback. In the above, if card#1 is selected, then USB audio data will take the legacy path over the USB PCM drivers, etc... The current limitation is that the latest USB audio device that is identified will be automatically selected by the Q6USB BE DAI for offloading. Future patches can be added to possibly add for more flexibility, but until the userpace applications can be better defined, having these mechanisms will complicate the overall implementation. USB offload Kcontrols ===================== Part of the vendor offload package will have a mixer driver associated with it (mixer_usb_offload.c). This entity will be responsible for coordinating with SOC USB and the Q6USB backend DAI to fetch information about the sound card and PCM device indices associated with the offload path. The logic is done based on the current implementation of how paths are controlled within the QC ASoC implementation. QC ASoC Q6Routing ----------------- Within the Q6 ASOC design, the registered ASoC platform card will expose a set of kcontrols for enabling the BE DAI links to the FE DAI link. For example: tinymix -D 0 contents Number of controls: 1033 ctl type num name value ... 1025 BOOL 1 USB Mixer MultiMedia1 Off 1026 BOOL 1 USB Mixer MultiMedia2 Off 1027 BOOL 1 USB Mixer MultiMedia3 Off 1028 BOOL 1 USB Mixer MultiMedia4 Off 1029 BOOL 1 USB Mixer MultiMedia5 Off 1030 BOOL 1 USB Mixer MultiMedia6 Off 1031 BOOL 1 USB Mixer MultiMedia7 Off 1032 BOOL 1 USB Mixer MultiMedia8 Off Each of these kcontrols will enable the USB BE DAI link (q6usb) to be connected to a FE DAI link (q6asm). Since each of these controls are DAPM widgets, when it is enabled, the DAPM widget's "connect" flag is updated accordingly. USB Offload Mapping ------------------- Based on the Q6routing, the USB BE DAI link can determine which sound card and PCM device is enabled for offloading. Fetching the ASoC platform sound card's information is fairly straightforward, and the bulk of the work goes to finding the corresponding PCM device index. As mentioned above, the USB BE DAI can traverse the DAPM widgets to find the DAPM path that is related to the control for the "USB Mixer." Based on which "USB Mixer" is enabled, it can find the corresponding DAPM widget associated w/ the FE DAI link (Multimedia*). From there it can find the PCM device created for the Multimedia* stream. Only one BE DAI link can be enabled per FE DAI. For example, if the HDMI path is enabled for Multimedia1, the USB Mixer will be disabled and switched over. Examples of kcontrol -------------------- tinymix -D 0 contents Number of controls: 1033 ctl type num name ... 1025 BOOL 1 USB Mixer MultiMedia1 Off 1026 BOOL 1 USB Mixer MultiMedia2 On 1027 BOOL 1 USB Mixer MultiMedia3 Off 1028 BOOL 1 USB Mixer MultiMedia4 Off 1029 BOOL 1 USB Mixer MultiMedia5 Off 1030 BOOL 1 USB Mixer MultiMedia6 Off 1031 BOOL 1 USB Mixer MultiMedia7 Off 1032 BOOL 1 USB Mixer MultiMedia8 Off tinymix -D 2 contents Number of controls: 7 ctl type num name value 0 INT 2 Playback Channel Map 0, 0 (range 0->36) 1 BOOL 2 MDR-1ADAC Playback Switch On, On 2 BOOL 1 MDR-1ADAC Playback Switch On 3 INT 2 MDR-1ADAC Playback Volume 127, 127 (range 0->127) 4 INT 1 MDR-1ADAC Playback Volume 127 (range 0->127) 5 BOOL 1 Sony Internal Clock Validity On 6 INT 2 USB Offload Playback Route PCM#0 0, 1 (range -1->255) The example highlights that the userspace/application can utilize the offload path for the USB device on card#0 PCM device#1. When dealing with multiple USB audio devices, only the latest USB device identified is going to be selected for offload capable. tinymix -D 1 contents Number of controls: 9 ctl type num name value 0 INT 2 Capture Channel Map 0, 0 (range 0->36) 1 INT 2 Playback Channel Map 0, 0 (range 0->36) 2 BOOL 1 Headset Capture Switch On 3 INT 1 Headset Capture Volume 1 (range 0->4) 4 BOOL 1 Sidetone Playback Switch On 5 INT 1 Sidetone Playback Volume 4096 (range 0->8192) 6 BOOL 1 Headset Playback Switch On 7 INT 2 Headset Playback Volume 20, 20 (range 0->24) 8 INT 2 USB Offload Playback Route PCM#0 -1, -1 (range -1->255) "-1, -1" shows that this device has no route to the offload path. This feature was validated using: - tinymix: set/enable the multimedia path to route to USB backend - tinyplay: issue playback on platform card Changelog -------------------------------------------- Changes in v26: - Cleaned up drivers based on errors from checkpatch - Fixed several typos using codespell - Removed any vendor specific notation from USB SND offload mixer patch Changes in v25: - Cleanups on typos mentioned within the xHCI layers - Modified the xHCI interrupter search if clients specify interrupter index - Moved mixer_usb_offload into its own module, so that other vendor offload USB modules can utilize it also. - Added support for USB audio devices that may have multiple PCM streams, as previous implementation only assumed a single PCM device. SOC USB will be able to handle an array of PCM indexes supported by the USB audio device. - Added some additional checks in the QC USB offload driver to check that device has at least one playback stream before allowing to bind - Reordered DT bindings to fix the error found by Rob's bot. The patch that added USB_RX was after the example was updated. - Updated comments within SOC USB to clarify terminology and to keep it consistent - Added SND_USB_JACK type for notifying of USB device audio connections Changes in v24: - Simplified the kcontrols involved in determining how to utilize the offload path. - There is one kcontrol registered to each USB audio device that will output which card/pcm device it is mapped to for the offload route. - Removed kcontrols to track offload status and device selection. - Default to last USB audio device plugged in as offload capable. - kcontrol will reside on USB SND device. - Reworked the tracking of connected USB devices from the Q6USB BE DAI link. Previously, it was convoluted by doing it over an array, but moved to using a list made it much simpler. Logic is still unchanged in that the last USB headset plugged in will be selected for offloading. - Updated the USB SOC RST documentation accordingly with new kcontrol updates. - Added logic to fetch mapped ASoC card and pcm device index that the offload path is mapped to for the USB SND kcontrol (for offload route). - Re-ordered series to hopefully make reviews more readable by combining patches based on the layer modified (ie QC ASoC, ASoC, USB sound, and USB XHCI). Changes in v23: - Added MODULE_DESCRIPTION() fields to drivers that needed it. Changes in v22: - Removed components tag for the ASoC platform card, as the USB SND kcontrol for notifying userspace of offload capable card achieves similar results. - Due to the above, had to remove the review-by tag for the RST documentation, as changes were made to remove the components tag section. - Took in feedback to make the SOC USB add/remove ports void. - Fixed an issue w/ the USB SND kcontrol management for devices that have multi UAC interfaces. (would attempt to create the kcontrol more than once) - Modified SOC USB card and PCM index select to be based off the num_supported streams that is specified by the USB BE DAI. - Modified comments on selecting the latest USB headset for offloading. Changes in v21: - Added an offload jack disable path from the ASoC platform driver and SOC USB. - Refactored some of the existing SOC USB context look up APIs and created some new helpers to search for the USB context. - Renamed snd_soc_usb_find_format to snd_soc_usb_find_supported_format - Removed some XHCI sideband calls that would allow clients to actually enable the IRQ line associated w/ the secondary interrupter. This is removed because there are other dependencies that are required for that to happen, which are not covered as part of this series, and to avoid confusion. - Due to the above, removed the need to export IMOD setting, and enable/disable interrupter APIs. Changes in v20: - Fixed up some formatting changes pointed out in the usb.rst - Added SB null check during XHCI sideband unregister in case caller passes improper argument (xhci_sideband_unregister()) Changes in v19: - Rebased to usb-next to account for some new changes in dependent drivers. Changes in v18: - Rebased to usb-next, which merged in part of the series. Removed these patches. - Reworked Kconfigs for the ASoC USB related components from QCOM Q6DSP drivers to keep dependencies in place for SoC USB and USB SND. - Removed the repurposing of the stop ep sync API into existing XHCI operations. This will be solely used by the XHCI sideband for now. Changes in v17: - Fixed an issue where one patch was squashed into another. - Re-added some kconfig checks for helpers exposed in USB SND for the soc usb driver, after running different kconfigs. Changes in v16: - Modified some code layer dependencies so that soc usb can be split as a separate module. - Split the kcontrols from ASoC QCOM common layer into a separate driver - Reworked SOC USB kcontrols for controlling card + pcm offload routing and status so that there are individual controls for card and pcm devices. - Added a kcontrol remove API in SOC USB to remove the controls on the fly. This required to add some kcontrol management to SOC USB. - Removed the disconnect work and workqueue for the QC USB offload as it is not required, since QMI interface driver ensures events are handled in its own WQ. Changes in v15: - Removed some already merged XHCI changes - Separated SOC USB driver from being always compiled into SOC core. Now configurable from kconfig. - Fixed up ASoC kcontrol naming to fit guidelines. - Removed some unnecessary dummy ifdefs. - Moved usb snd offload capable kcontrol to be initialized by the platform offloading driver. Changes in v14: - Cleaned up some USB SND related feedback: - Renamed SNDUSB OFFLD playback available --> USB offload capable card - Fixed locking while checking if stream is in use - Replaced some mutex pairs with guard(mutex) Changes in v13: - Pulled in secondary/primary interrupter rework from Mathias from: https://git.kernel.org/pub/scm/linux/kernel/git/mnyman/xhci.git/log/drivers… - Did some cleanup and commit message updates, and tested on current code base. - Added mutex locking to xhci sideband to help prevent any race conditions, esp. for when accessing shared references. - Addressed concerns from Hillf about gfp_flags and locking used in qc_usb_audio_offload. - Rebased onto usb-next Changes in v12: - Updated copyright year to 2024. Happy new years! - Fixed newline format on mixer offload driver. Changes in v11: - Modified QMI format structures to be const Changes in v10: - Added new mixer for exposing kcontrol for sound card created by USB SND. This allows for applications to know which platform sound card has offload support. Will return the card number. - Broke down and cleaned up some functions/APIs within qc_audio_offload driver. - Exported xhci_initialize_ring_info(), and modified XHCI makefile to allow for the XHCI sideband to exist as a module. - Reworked the jack registration and moved it to the QCOM platform card driver, ie sm8250. - Added an SOC USB API to fetch a standard component tag that can be appended to the platform sound card. Added this tag to sm8250 if any USB path exists within the DT node. - Moved kcontrols that existed in the Q6USB driver, and made it a bit more generic, so that naming can be standardized across solutions. SOC USB is now responsible for creation of these kcontrols. - Added a SOC USB RST document explaining some code flows and implementation details so that other vendors can utilize the framework. - Addressed a case where USB device connection events are lost if usb offload driver (qc_audio_offload) is not probed when everything else has been initialized, ie USB SND, SOC USB and ASoC sound card. Add a rediscover device call during module init, to ensure that connection events will be propagated. - Rebased to usb-next. Changes in v9: - Fixed the dt binding check issue with regards to num-hc-interrupters. Changes in v8: - Cleaned up snd_soc_usb_find_priv_data() based on Mark's feedback. Removed some of the duplicate looping code that was present on previous patches. Also renamed the API. - Integrated Mathias' suggestions on his new sideband changes: https://git.kernel.org/pub/scm/linux/kernel/git/mnyman/xhci.git/log/?h=feat… - Addressed some of Mathias' fixme tags, such as: - Resetting transfer ring dequeue/enqueue pointers - Issuing stop endpoint command during ep removal - Reset ERDP properly to first segment ring during interrupter removal. (this is currently just being cleared to 0, but should be pointing to a valid segment if controller is still running. Changes in v7: - Fixed dt check error for q6usb bindings - Updated q6usb property from qcom,usb-audio-intr-num --> qcom,usb-audio-intr-idx - Removed separate DWC3 HC interrupters num property, and place limits to XHCI one. - Modified xhci_ring_to_sgtable() to use assigned IOVA/DMA address to fetch pages, as it is not ensured event ring allocated is always done in the vmalloc range. Changes in v6: - Fixed limits and description on several DT bindings (XHCI and Q6USB) - Fixed patch subjects to follow other ALSA/ASoC notations. USB SND - Addressed devices which expose multiple audio (UAC) interfaces. These devices will create a single USB sound card with multiple audio streams, and receive multiple interface probe routines. QC offload was not properly considering cases with multiple probe calls. - Renamed offload module name and kconfig to fit within the SND domain. - Renamed attach/detach endpoint API to keep the hw_params notation. Changes in v5: - Removed some unnecessary files that were included - Fixed some typos mentioned - Addressed dt-binding issues and added hc-interrupters definition to usb-xhci.yaml XHCI: - Moved secondary skip events API to xhci-ring and updated implementation - Utilized existing XHCI APIs, such as inc_deq and xhci_update_erst_dequeue() USB SND - Renamed and reworked the APIs in "sound: usb: Export USB SND APIs for modules" patch to include suggestions to utilize snd_usb_hw_params/free and to avoid generic naming. - Added a resume_cb() op for completion sake. - Addressed some locking concerns with regards to when registering for platform hooks. - Added routine to disconnect all offloaded devices during module unbind. ASoC - Replaced individual PCM parameter arguments in snd_soc_usb_connect() with new snd_soc_usb_device structure to pass along PCM info. - Modified snd_jack set report to notify HEADPHONE event, as we do not support record path. Changes in v4: - Rebased to xhci/for-usb-next - Addressed some dt-bindings comments XHCI: - Pulled in latest changes from Mathias' feature_interrupters branch: https://git.kernel.org/pub/scm/linux/kernel/git/mnyman/xhci.git/log/?h=feat… - Fixed commit text and signage for the XHCI sideband/interrupter related changes - Added some logic to address the FIXME tags mentioned throughout the commits, such as handling multi segment rings and building the SGT, locking concerns, and ep cleanup operations. - Removed some fixme tags for conditions that may not be needed/addressed. - Repurposed the new endpoint stop sync API to be utilized in other places. - Fixed potential compile issue if XHCI sideband config is not defined. ASoC: - Added sound jack control into the Q6USB driver. Allows for userspsace to know when an offload capable device is connected. USB SND: - Avoided exporting _snd_pcm_hw_param_set based on Takashi's recommendation. - Split USB QMI packet header definitions into a separate commit. This is used to properly allow the QMI interface driver to parse and route QMI packets accordingly - Added a "depends on" entry when enabling QC audio offload to avoid compile time issues. Changes in v3: - Changed prefix from RFC to PATCH - Rebased entire series to usb-next - Updated copyright years XHCI: - Rebased changes on top of XHCI changes merged into usb-next, and only added changes that were still under discussion. - Added change to read in the "num-hc-interrupters" device property. ASoC: - qusb6 USB backend - Incorporated suggestions to fetch iommu information with existing APIs - Added two new sound kcontrols to fetch offload status and offload device selection. - offload status - will return the card and pcm device in use tinymix -D 0 get 1 --> 1, 0 (offload in progress on card#1 pcm#0) - device selection - set the card and pcm device to enable offload on. Ex.: tinymix -D 0 set 1 2 0 --> sets offload on card#2 pcm#0 (this should be the USB card) USB SND: - Fixed up some locking related concerns for registering platform ops. - Moved callbacks under the register_mutex, so that - Modified APIs to properly pass more information about the USB SND device, so that the Q6USB backend can build a device list/map, in order to monitor offload status and device selection. Changes in v2: XHCI: - Replaced XHCI and HCD changes with Mathias' XHCI interrupter changes in his tree: https://git.kernel.org/pub/scm/linux/kernel/git/mnyman/xhci.git/log/?h=feat… Adjustments made to Mathias' changes: - Created xhci-intr.h to export/expose interrupter APIs versus exposing xhci.h. Moved dependent structures to this file as well. (so clients can parse out information from "struct xhci_interrupter") - Added some basic locking when requesting interrupters. - Fixed up some sanity checks. - Removed clearing of the ERSTBA during freeing of the interrupter. (pending issue where SMMU fault occurs if DMA addr returned is 64b - TODO) - Clean up pending events in the XHCI secondary interrupter. While testing USB bus suspend, it was seen that on bus resume, the xHCI HC would run into a command timeout. - Added offloading APIs to xHCI to fetch transfer and event ring information. ASoC: - Modified soc-usb to allow for multiple USB port additions. For this to work, the USB offload driver has to have a reference to the USB backend by adding a "usb-soc-be" DT entry to the device saved into XHCI sysdev. - Created separate dt-bindings for defining USB_RX port. - Increased APR timeout to accommodate the situation where the AFE port start command could be delayed due to having to issue a USB bus resume while handling the QMI stream start command. Mathias Nyman (2): xhci: add helper to stop endpoint and wait for completion xhci: sideband: add initial api to register a sideband entity Wesley Cheng (31): usb: host: xhci: Repurpose event handler for skipping interrupter events usb: xhci: Allow for secondary interrupter to set IMOD usb: host: xhci-mem: Cleanup pending secondary event ring events usb: host: xhci-mem: Allow for interrupter clients to choose specific index usb: host: xhci-plat: Set XHCI max interrupters if property is present usb: dwc3: Specify maximum number of XHCI interrupters ALSA: Add USB audio device jack type ALSA: usb-audio: Export USB SND APIs for modules ALSA: usb-audio: Check for support for requested audio format ASoC: Add SOC USB APIs for adding an USB backend ASoC: usb: Add PCM format check API for USB backend ASoC: usb: Create SOC USB SND jack kcontrol ASoC: usb: Fetch ASoC card and pcm device information ASoC: doc: Add documentation for SOC USB ASoC: dt-bindings: qcom,q6dsp-lpass-ports: Add USB_RX port ASoC: dt-bindings: Update example for enabling USB offload on SM8250 ASoC: qcom: qdsp6: Introduce USB AFE port to q6dsp ASoC: qcom: qdsp6: q6afe: Increase APR timeout ASoC: qcom: qdsp6: Add USB backend ASoC driver for Q6 ASoC: qcom: qdsp6: Add headphone jack for offload connection status ASoC: qcom: qdsp6: Fetch USB offload mapped card and PCM device ALSA: usb-audio: Introduce USB SND platform op callbacks ALSA: usb-audio: Save UAC sample size information ALSA: usb-audio: Prevent starting of audio stream if in use ALSA: usb-audio: qcom: Add USB QMI definitions ALSA: usb-audio: qcom: Introduce QC USB SND offloading support ALSA: usb-audio: qcom: Don't allow USB offload path if PCM device is in use ALSA: usb-audio: qcom: Use card and PCM index from QMI request ALSA: usb-audio: Add USB offload route kcontrol ALSA: usb-audio: Allow for rediscovery of connected USB SND devices ASoC: usb: Rediscover USB SND devices on USB port add .../bindings/sound/qcom,sm8250.yaml | 15 + Documentation/sound/soc/index.rst | 1 + Documentation/sound/soc/usb.rst | 429 ++++ drivers/usb/dwc3/core.c | 12 + drivers/usb/dwc3/core.h | 2 + drivers/usb/dwc3/host.c | 3 + drivers/usb/host/Kconfig | 9 + drivers/usb/host/Makefile | 2 + drivers/usb/host/xhci-mem.c | 34 +- drivers/usb/host/xhci-plat.c | 2 + drivers/usb/host/xhci-ring.c | 54 +- drivers/usb/host/xhci-sideband.c | 425 ++++ drivers/usb/host/xhci.c | 45 +- drivers/usb/host/xhci.h | 19 +- .../sound/qcom,q6dsp-lpass-ports.h | 1 + include/linux/mod_devicetable.h | 2 +- include/linux/usb/xhci-sideband.h | 71 + include/sound/jack.h | 4 +- include/sound/q6usboffload.h | 20 + include/sound/soc-usb.h | 135 ++ include/uapi/linux/input-event-codes.h | 3 +- sound/core/jack.c | 6 +- sound/soc/Kconfig | 10 + sound/soc/Makefile | 2 + sound/soc/qcom/Kconfig | 15 + sound/soc/qcom/Makefile | 2 + sound/soc/qcom/qdsp6/Makefile | 1 + sound/soc/qcom/qdsp6/q6afe-dai.c | 60 + sound/soc/qcom/qdsp6/q6afe.c | 194 +- sound/soc/qcom/qdsp6/q6afe.h | 36 +- sound/soc/qcom/qdsp6/q6dsp-lpass-ports.c | 23 + sound/soc/qcom/qdsp6/q6dsp-lpass-ports.h | 1 + sound/soc/qcom/qdsp6/q6routing.c | 9 + sound/soc/qcom/qdsp6/q6usb.c | 391 ++++ sound/soc/qcom/sm8250.c | 24 +- sound/soc/qcom/usb_offload_utils.c | 56 + sound/soc/qcom/usb_offload_utils.h | 30 + sound/soc/soc-usb.c | 338 +++ sound/usb/Kconfig | 25 + sound/usb/Makefile | 4 +- sound/usb/card.c | 110 + sound/usb/card.h | 17 + sound/usb/endpoint.c | 1 + sound/usb/format.c | 1 + sound/usb/helper.c | 1 + sound/usb/mixer_usb_offload.c | 102 + sound/usb/mixer_usb_offload.h | 17 + sound/usb/pcm.c | 104 +- sound/usb/pcm.h | 11 + sound/usb/qcom/Makefile | 2 + sound/usb/qcom/qc_audio_offload.c | 1968 +++++++++++++++++ sound/usb/qcom/usb_audio_qmi_v01.c | 863 ++++++++ sound/usb/qcom/usb_audio_qmi_v01.h | 164 ++ 53 files changed, 5820 insertions(+), 56 deletions(-) create mode 100644 Documentation/sound/soc/usb.rst create mode 100644 drivers/usb/host/xhci-sideband.c create mode 100644 include/linux/usb/xhci-sideband.h create mode 100644 include/sound/q6usboffload.h create mode 100644 include/sound/soc-usb.h create mode 100644 sound/soc/qcom/qdsp6/q6usb.c create mode 100644 sound/soc/qcom/usb_offload_utils.c create mode 100644 sound/soc/qcom/usb_offload_utils.h create mode 100644 sound/soc/soc-usb.c create mode 100644 sound/usb/mixer_usb_offload.c create mode 100644 sound/usb/mixer_usb_offload.h create mode 100644 sound/usb/qcom/Makefile create mode 100644 sound/usb/qcom/qc_audio_offload.c create mode 100644 sound/usb/qcom/usb_audio_qmi_v01.c create mode 100644 sound/usb/qcom/usb_audio_qmi_v01.h

2 64

[PATCH] ASoC: dt-bindings: renesas,rsnd: add post-init-providers property
by Kuninori Morimoto 04 Sep '24

04 Sep '24

sometimes, fwnode dependency cycles can be broken, and in such case, rsnd driver will never be probed. To avoid such case, we would like to use post-init-providers to avoid it. Enable post-init-providers property on rsnd. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx(a)renesas.com> --- Documentation/devicetree/bindings/sound/renesas,rsnd.yaml | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.yaml b/Documentation/devicetree/bindings/sound/renesas,rsnd.yaml index 07ec6247d9def..cb44478d9e420 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.yaml +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.yaml @@ -112,6 +112,10 @@ properties: description: List of necessary clock names. # details are defined below + post-init-providers: + description: ignore fw_devlink dependency cycles and avoid driver probe dead-lock + $ref: /schemas/types.yaml#/definitions/phandle-array + # ports is below port: $ref: audio-graph-port.yaml#/definitions/port-base -- 2.43.0

3 2

[PATCH 00/12] Add i2s/tdm support for acp7.0 and acp7.1 platforms
by Venkata Prasad Potturu 04 Sep '24

04 Sep '24

1. Refactor acp generic driver to support all platforms. 2. Add i2s/tdm and support for acp7.0 and acp7.1 platforms. Venkata Prasad Potturu (12): ASoC: amd: acp: Refactor TDM slots selction based on acp revision id ASoC: amd: acp: Refactor I2S dai driver ASoC: amd: acp: Update pcm hardware capabilities for acp6.3 platform ASoC: amd: acp: Add I2S TDM support for acp6.3 platform ASoC: amd: acp: Update pcm hardware capabilities for acp7.0 platform ASoC: amd: acp: Add I2S master clock generation support for acp7.0 platform ASoC: amd: acp: Set i2s clock for acp7.0 platform ASoC: amd: acp: Modify max channels and sample rate support for acp70 dai driver ASoC: amd: acp: Add I2S TDM support for acp7.0 platform ASoC: amd: acp: Add pte configuration for ACP7.0 platform ASoC: amd: acp: Add i2s master clock generation support for acp7.1 platform ASoC: amd: acp: Add I2S TDM support for acp7.1 platform sound/soc/amd/acp/acp-i2s.c | 188 ++++++++++++++++++++------ sound/soc/amd/acp/acp-legacy-common.c | 32 ++--- sound/soc/amd/acp/acp-pdm.c | 7 +- sound/soc/amd/acp/acp-platform.c | 117 ++++++++++++++-- sound/soc/amd/acp/acp70.c | 73 +++++++--- sound/soc/amd/acp/amd.h | 24 ++-- sound/soc/amd/acp/chip_offset_byte.h | 84 +++++++----- 7 files changed, 387 insertions(+), 138 deletions(-) -- 2.39.2

2 13

[PATCH] ALSA: hda/realtek: Support mute LED on HP Laptop 14-dq2xxx
by Maximilien Perreault 04 Sep '24

04 Sep '24

The mute LED on this HP laptop uses ALC236 and requires a quirk to function. This patch enables the existing quirk for the device. Signed-off-by: Maximilien Perreault <maximilienperreault(a)gmail.com> --- sound/pci/hda/patch_realtek.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index f67190a8c..6f96c0c67 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -10183,6 +10183,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x103c, 0x87f5, "HP", ALC287_FIXUP_HP_GPIO_LED), SND_PCI_QUIRK(0x103c, 0x87f6, "HP Spectre x360 14", ALC245_FIXUP_HP_X360_AMP), SND_PCI_QUIRK(0x103c, 0x87f7, "HP Spectre x360 14", ALC245_FIXUP_HP_X360_AMP), + SND_PCI_QUIRK(0x103c, 0x87fd, "HP Laptop 14-dq2xxx", ALC236_FIXUP_HP_MUTE_LED_COEFBIT2), SND_PCI_QUIRK(0x103c, 0x87fe, "HP Laptop 15s-fq2xxx", ALC236_FIXUP_HP_MUTE_LED_COEFBIT2), SND_PCI_QUIRK(0x103c, 0x8805, "HP ProBook 650 G8 Notebook PC", ALC236_FIXUP_HP_GPIO_LED), SND_PCI_QUIRK(0x103c, 0x880d, "HP EliteBook 830 G8 Notebook PC", ALC285_FIXUP_HP_GPIO_LED), -- 2.46.0

2 1

[PATCH] soc: qcom: apr: Fix some parenthesis alignment coding style issues
by Riyan Dhiman 04 Sep '24

04 Sep '24

Adhere to Linux kernel coding style. Issue reported by checkpatch: - CHECK: Alignment should match open parenthesis It has no functional changes. Signed-off-by: Riyan Dhiman <riyandhiman14(a)gmail.com> --- drivers/soc/qcom/apr.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/drivers/soc/qcom/apr.c b/drivers/soc/qcom/apr.c index 4fbff3a890e2..db1326bdb170 100644 --- a/drivers/soc/qcom/apr.c +++ b/drivers/soc/qcom/apr.c @@ -88,7 +88,7 @@ void gpr_free_port(gpr_port_t *port) EXPORT_SYMBOL_GPL(gpr_free_port); gpr_port_t *gpr_alloc_port(struct apr_device *gdev, struct device *dev, - gpr_port_cb cb, void *priv) + gpr_port_cb cb, void *priv) { struct packet_router *pr = dev_get_drvdata(gdev->dev.parent); gpr_port_t *port; @@ -159,7 +159,7 @@ static void apr_dev_release(struct device *dev) } static int apr_callback(struct rpmsg_device *rpdev, void *buf, - int len, void *priv, u32 addr) + int len, void *priv, u32 addr) { struct packet_router *apr = dev_get_drvdata(&rpdev->dev); struct apr_rx_buf *abuf; @@ -222,9 +222,9 @@ static int apr_do_rx_callback(struct packet_router *apr, struct apr_rx_buf *abuf } if (hdr->src_domain >= APR_DOMAIN_MAX || - hdr->dest_domain >= APR_DOMAIN_MAX || - hdr->src_svc >= APR_SVC_MAX || - hdr->dest_svc >= APR_SVC_MAX) { + hdr->dest_domain >= APR_DOMAIN_MAX || + hdr->src_svc >= APR_SVC_MAX || + hdr->dest_svc >= APR_SVC_MAX) { dev_err(apr->dev, "APR: Wrong APR header\n"); return -EINVAL; } -- 2.46.0

2 1

Qestion: of property has dead-lock to call .probe()
by Kuninori Morimoto 04 Sep '24

04 Sep '24

Hi Saravana, Rob Cc Mark/ALSA-ML, Geert, Laurent I got dead-lock issue on drivers/of/property.c to call .probe() I'm now using v6.11-rc5. I'm using 3 devices, and these are connected via OF-Graph. These are connected like this so far. Let's call it as [Style-A] [Style-A] +---+ +---+ |(A)+--+ | +-+-+ | | | |(B)| +-+-+ | | |(C)+--+ | +---+ +---+ These are using port/endpoint to connect. It works well for now, no issue I have so far. (B) is connector for (A)-(C) data, thus, (A) and (C) should be probed first, and (B) needs probe later (For ALSA member, this (B) is Audio Graph Card2). Here, (A)-(C) can connect directly for some data. Now it is using both data connection (= (A)-(B)-(C) and (A)-(C)) Now, I want to disconnect (A)-(C) connection, like below Let's call it as [Style-B] [Style-B] +---+ +---+ |(A)+--+ | +---+ | | |(B)| +---+ | | |(C)+--+ | +---+ +---+ Then, it seems dead-lock happen. In my debug, it seems... - (B) is handled as supplier for (A). - (B) probe() is called, but it needs (A) info which is not yet probed. So it returns -EPROBE_DEFER. - Because (B) is not probed, (A) probe() never called In [Style-A], it seems __fwnode_link_cycle() is called for (A)-(B) connection, so the dead-lock will be solved. But it is not called for [Style-B]. Because of that (B) is always handled as supplier for (A). If I used below patch, and use "non-supplier" property on (B), this dead-lock issue was solved. But I know this is not a good solution. I think it is very normal connection, not super special. How can I solve this issue on correct way ? Or how can I indicate you my issue more detail ? I can add debug patch and test it if you can indicate it to me. ----------------------------------------------- diff --git a/drivers/of/property.c b/drivers/of/property.c index def152c61049..2f08210c2ea4 100644 --- a/drivers/of/property.c +++ b/drivers/of/property.c @@ -1502,11 +1502,22 @@ static struct device_node *parse_remote_endpoint(struct device_node *np, const char *prop_name, int index) { + struct device_node *node; + /* Return NULL for index > 0 to signify end of remote-endpoints. */ if (index > 0 || strcmp(prop_name, "remote-endpoint")) return NULL; - return of_graph_get_remote_port_parent(np); + node = of_graph_get_remote_port_parent(np); + + /* + * There is clearly non-supplier node which is connected via "remote-endpoint". + * Ignore it, otherwise dead-lock might occur + */ + if (of_property_present(node, "non-supplier")) + return NULL; + + return node; } ----------------------------------------------- Thank you for your help !! Best regards --- Kuninori Morimoto

2 2

[PATCH] ASoC: tlv320aic32x4: Add multi endpoint support
by Marek Vasut 04 Sep '24

04 Sep '24

Support multiple endpoints on TLV320AIC32x4 codec port when used in of_graph context. This patch allows to share the codec port between two CPU DAIs. Example: Custom STM32MP157C board uses TLV320AIC32x4 audio codec. This codec is connected to two serial audio interfaces, which are configured either as rx or tx. From AsoC point of view the topolgy is the following: // 2 CPU DAIs (SAI2A/B), 1 Codec (TLV320AIC32x4) Playback: CPU-A-DAI(slave) -> (master)CODEC-DAI/port0 Record: CPU-B-DAI(slave) <- (master)CODEC-DAI/port0 In the DT two endpoints have to be associated to the codec port: tlv320aic32x4_port: port { tlv320aic32x4_tx_endpoint: endpoint@0 { remote-endpoint = <&sai2a_endpoint>; }; tlv320aic32x4_rx_endpoint: endpoint@1 { remote-endpoint = <&sai2b_endpoint>; }; }; However, when the audio graph card parses the codec nodes, it expects to find DAI interface indexes matching the endpoints indexes. The current patch forces the use of DAI id 0 for both endpoints, which allows to share the codec DAI between the two CPU DAIs for playback and capture streams respectively. Signed-off-by: Marek Vasut <marex(a)denx.de> --- Cc: Baojun Xu <baojun.xu(a)ti.com> Cc: Charles Keepax <ckeepax(a)opensource.cirrus.com> Cc: Christoph Niedermaier <cniedermaier(a)dh-electronics.com> Cc: Jaroslav Kysela <perex(a)perex.cz> Cc: Kevin Lu <kevin-lu(a)ti.com> Cc: Liam Girdwood <lgirdwood(a)gmail.com> Cc: Marek Vasut <marex(a)denx.de> Cc: Mark Brown <broonie(a)kernel.org> Cc: Philipp Zabel <p.zabel(a)pengutronix.de> Cc: Shenghao Ding <shenghao-ding(a)ti.com> Cc: Takashi Iwai <tiwai(a)suse.com> Cc: alsa-devel(a)alsa-project.org Cc: kernel(a)dh-electronics.com Cc: linux-sound(a)vger.kernel.org --- sound/soc/codecs/tlv320aic32x4.c | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/sound/soc/codecs/tlv320aic32x4.c b/sound/soc/codecs/tlv320aic32x4.c index 5c0c81da06dba..54ea4bc58c276 100644 --- a/sound/soc/codecs/tlv320aic32x4.c +++ b/sound/soc/codecs/tlv320aic32x4.c @@ -1073,6 +1073,13 @@ static int aic32x4_component_probe(struct snd_soc_component *component) return 0; } +static int aic32x4_of_xlate_dai_id(struct snd_soc_component *component, + struct device_node *endpoint) +{ + /* return dai id 0, whatever the endpoint index */ + return 0; +} + static const struct snd_soc_component_driver soc_component_dev_aic32x4 = { .probe = aic32x4_component_probe, .set_bias_level = aic32x4_set_bias_level, @@ -1082,6 +1089,7 @@ static const struct snd_soc_component_driver soc_component_dev_aic32x4 = { .num_dapm_widgets = ARRAY_SIZE(aic32x4_dapm_widgets), .dapm_routes = aic32x4_dapm_routes, .num_dapm_routes = ARRAY_SIZE(aic32x4_dapm_routes), + .of_xlate_dai_id = aic32x4_of_xlate_dai_id, .suspend_bias_off = 1, .idle_bias_on = 1, .use_pmdown_time = 1, @@ -1203,6 +1211,7 @@ static const struct snd_soc_component_driver soc_component_dev_aic32x4_tas2505 = .num_dapm_widgets = ARRAY_SIZE(aic32x4_tas2505_dapm_widgets), .dapm_routes = aic32x4_tas2505_dapm_routes, .num_dapm_routes = ARRAY_SIZE(aic32x4_tas2505_dapm_routes), + .of_xlate_dai_id = aic32x4_of_xlate_dai_id, .suspend_bias_off = 1, .idle_bias_on = 1, .use_pmdown_time = 1, -- 2.45.2

2 1

[PATCH] ASOC: Intel: fix parenthesis alignment and space after cast coding style issue
by Riyan Dhiman 03 Sep '24

03 Sep '24

Adhere to Linux kernel coding style. Reported by checkpatch: - CHECK: Alignment should match open parenthesis - CHECK: No space is necessary after a cast It has no functional changes. Signed-off-by: Riyan Dhiman <riyandhiman14(a)gmail.com> --- sound/soc/intel/atom/sst/sst.c | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) diff --git a/sound/soc/intel/atom/sst/sst.c b/sound/soc/intel/atom/sst/sst.c index e0357d257c6c..38d29d545b52 100644 --- a/sound/soc/intel/atom/sst/sst.c +++ b/sound/soc/intel/atom/sst/sst.c @@ -50,7 +50,7 @@ static irqreturn_t intel_sst_interrupt_mrfld(int irq, void *context) union sst_imr_reg_mrfld imr; struct ipc_post *msg = NULL; unsigned int size; - struct intel_sst_drv *drv = (struct intel_sst_drv *) context; + struct intel_sst_drv *drv = (struct intel_sst_drv *)context; irqreturn_t retval = IRQ_HANDLED; /* Interrupt arrived, check src */ @@ -60,7 +60,7 @@ static irqreturn_t intel_sst_interrupt_mrfld(int irq, void *context) /* Clear done bit */ spin_lock(&drv->ipc_spin_lock); header.full = sst_shim_read64(drv->shim, - drv->ipc_reg.ipcx); + drv->ipc_reg.ipcx); header.p.header_high.part.done = 0; sst_shim_write64(drv->shim, drv->ipc_reg.ipcx, header.full); @@ -92,7 +92,7 @@ static irqreturn_t intel_sst_interrupt_mrfld(int irq, void *context) size = header.p.header_low_payload; if (sst_validate_mailbox_size(size)) { memcpy_fromio(msg->mailbox_data, - drv->mailbox + drv->mailbox_recv_offset, size); + drv->mailbox + drv->mailbox_recv_offset, size); } else { dev_err(drv->dev, "Mailbox not copied, payload size is: %u\n", size); @@ -114,7 +114,7 @@ static irqreturn_t intel_sst_interrupt_mrfld(int irq, void *context) static irqreturn_t intel_sst_irq_thread_mrfld(int irq, void *context) { - struct intel_sst_drv *drv = (struct intel_sst_drv *) context; + struct intel_sst_drv *drv = (struct intel_sst_drv *)context; struct ipc_post *__msg, *msg; unsigned long irq_flags; @@ -146,8 +146,8 @@ static int sst_save_dsp_context_v2(struct intel_sst_drv *sst) int ret = 0; ret = sst_prepare_and_post_msg(sst, SST_TASK_ID_MEDIA, IPC_CMD, - IPC_PREP_D3, PIPE_RSVD, 0, NULL, NULL, - true, true, false, true); + IPC_PREP_D3, PIPE_RSVD, 0, NULL, NULL, + true, true, false, true); if (ret < 0) { dev_err(sst->dev, "not suspending FW!!, Err: %d\n", ret); @@ -228,7 +228,7 @@ static void sst_init_locks(struct intel_sst_drv *ctx) * we are fine with using unsigned short as dev_id type. */ int sst_alloc_drv_context(struct intel_sst_drv **ctx, - struct device *dev, unsigned short dev_id) + struct device *dev, unsigned short dev_id) { *ctx = devm_kzalloc(dev, sizeof(struct intel_sst_drv), GFP_KERNEL); if (!(*ctx)) @@ -242,7 +242,7 @@ int sst_alloc_drv_context(struct intel_sst_drv **ctx, EXPORT_SYMBOL_GPL(sst_alloc_drv_context); static ssize_t firmware_version_show(struct device *dev, - struct device_attribute *attr, char *buf) + struct device_attribute *attr, char *buf) { struct intel_sst_drv *ctx = dev_get_drvdata(dev); @@ -302,7 +302,7 @@ int sst_context_init(struct intel_sst_drv *ctx) ctx->ipc_reg.ipcd = SST_IPCD + ctx->pdata->ipc_info->ipc_offset; dev_info(ctx->dev, "Got drv data max stream %d\n", - ctx->info.max_streams); + ctx->info.max_streams); for (i = 1; i <= ctx->info.max_streams; i++) { struct stream_info *stream = &ctx->streams[i]; @@ -325,7 +325,7 @@ int sst_context_init(struct intel_sst_drv *ctx) sst_shim_write64(ctx->shim, SST_IMRX, 0xFFFF0038); ctx->qos = devm_kzalloc(ctx->dev, - sizeof(struct pm_qos_request), GFP_KERNEL); + sizeof(struct pm_qos_request), GFP_KERNEL); if (!ctx->qos) { ret = -ENOMEM; goto do_free_mem; -- 2.46.0

1 0

ucm2: sof-soundwire: add RT1320 amplifier
by GitHub pull_request - opened 03 Sep '24

03 Sep '24

alsa-project/alsa-ucm-conf pull request #439 was opened from shumingfan: Add support for rt1320 amplifier Request URL : https://github.com/alsa-project/alsa-ucm-conf/pull/439 Patch URL : https://github.com/alsa-project/alsa-ucm-conf/pull/439.patch Repository URL: https://github.com/alsa-project/alsa-ucm-conf

1 0

[PATCH v2] ASoC: tas2781: Add Calibration Kcontrols for Chromebook
by Shenghao Ding 03 Sep '24

03 Sep '24

Add calibration related kcontrol for speaker impedance calibration and speaker leakage check for Chromebook Signed-off-by: Shenghao Ding <shenghao-ding(a)ti.com> --- v2: - Add channel no into the log for error debug - | Reported-by: kernel test robot <lkp(a)intel.com> | Closes: https://urldefense.com/v3/__https://lore.kernel.org/oe-kbuild-all/202407131… - renamae tasdevice_chn_switch to put it in a single line - With inverted check this entire function becomes neater in tasdev_chn_switch. - Add registers for TAS2563 and TAS2781 calibration. - Add cali_data_backup for regsiter restore after calibration. - Add is_user_space_calidata to store the flag where the calibrated from, user space or bin file from driver parsing. - tasdevice_chn_switch for chip switch among multiple chips(tas2563 or tas2781) - Add loading the calibrated values from user space in tasdev_load_calibrated_data - Correct no dsp no work, it can still work in bypass mode. - Add calibrated register setting for tas2563&tas2781. - Define tas2781_cali_control and tas2563_cali_control for calibration --- include/sound/tas2781.h | 68 +++ sound/soc/codecs/tas2781-comlib.c | 26 + sound/soc/codecs/tas2781-fmwlib.c | 60 +- sound/soc/codecs/tas2781-i2c.c | 961 +++++++++++++++++++++++++++++- 4 files changed, 1104 insertions(+), 11 deletions(-) diff --git a/include/sound/tas2781.h b/include/sound/tas2781.h index dbda552398b5..a9ccbbd1945c 100644 --- a/include/sound/tas2781.h +++ b/include/sound/tas2781.h @@ -49,12 +49,59 @@ /*I2C Checksum */ #define TASDEVICE_I2CChecksum TASDEVICE_REG(0x0, 0x0, 0x7E) +/* XM_340 */ +#define TASDEVICE_XM_A1_REG TASDEVICE_REG(0x64, 0x02, 0x4c) +/* XM_341 */ +#define TASDEVICE_XM_A2_REG TASDEVICE_REG(0x64, 0x02, 0x64) + /* Volume control */ #define TAS2563_DVC_LVL TASDEVICE_REG(0x00, 0x02, 0x0C) #define TAS2781_DVC_LVL TASDEVICE_REG(0x0, 0x0, 0x1A) #define TAS2781_AMP_LEVEL TASDEVICE_REG(0x0, 0x0, 0x03) #define TAS2781_AMP_LEVEL_MASK GENMASK(5, 1) +#define TAS2563_IDLE TASDEVICE_REG(0x00, 0x00, 0x3e) +#define TAS2563_PRM_R0_REG TASDEVICE_REG(0x00, 0x0f, 0x34) + +#define TAS2563_RUNTIME_RE_REG_TF TASDEVICE_REG(0x64, 0x02, 0x70) +#define TAS2563_RUNTIME_RE_REG TASDEVICE_REG(0x64, 0x02, 0x48) + +#define TAS2563_PRM_ENFF_REG TASDEVICE_REG(0x00, 0x0d, 0x54) +#define TAS2563_PRM_DISTCK_REG TASDEVICE_REG(0x00, 0x0d, 0x58) +#define TAS2563_PRM_TE_SCTHR_REG TASDEVICE_REG(0x00, 0x0f, 0x60) +#define TAS2563_PRM_PLT_FLAG_REG TASDEVICE_REG(0x00, 0x0d, 0x74) +#define TAS2563_PRM_SINEGAIN_REG TASDEVICE_REG(0x00, 0x0d, 0x7c) +/* prm_Int_B0 */ +#define TAS2563_TE_TA1_REG TASDEVICE_REG(0x00, 0x10, 0x0c) +/* prm_Int_A1 */ +#define TAS2563_TE_TA1_AT_REG TASDEVICE_REG(0x00, 0x10, 0x10) +/* prm_TE_Beta */ +#define TAS2563_TE_TA2_REG TASDEVICE_REG(0x00, 0x0f, 0x64) +/* prm_TE_Beta1 */ +#define TAS2563_TE_AT_REG TASDEVICE_REG(0x00, 0x0f, 0x68) +/* prm_TE_1_Beta1 */ +#define TAS2563_TE_DT_REG TASDEVICE_REG(0x00, 0x0f, 0x70) + +#define TAS2781_PRM_INT_MASK_REG TASDEVICE_REG(0x00, 0x00, 0x3b) +#define TAS2781_PRM_CLK_CFG_REG TASDEVICE_REG(0x00, 0x00, 0x5c) +#define TAS2781_PRM_RSVD_REG TASDEVICE_REG(0x00, 0x01, 0x19) +#define TAS2781_PRM_TEST_57_REG TASDEVICE_REG(0x00, 0xfd, 0x39) +#define TAS2781_PRM_TEST_62_REG TASDEVICE_REG(0x00, 0xfd, 0x3e) +#define TAS2781_PRM_PVDD_UVLO_REG TASDEVICE_REG(0x00, 0x00, 0x71) +#define TAS2781_PRM_CHNL_0_REG TASDEVICE_REG(0x00, 0x00, 0x03) +#define TAS2781_PRM_NG_CFG0_REG TASDEVICE_REG(0x00, 0x00, 0x35) +#define TAS2781_PRM_IDLE_CH_DET_REG TASDEVICE_REG(0x00, 0x00, 0x66) +#define TAS2781_PRM_PLT_FLAG_REG TASDEVICE_REG(0x00, 0x14, 0x38) +#define TAS2781_PRM_SINEGAIN_REG TASDEVICE_REG(0x00, 0x14, 0x40) +#define TAS2781_PRM_SINEGAIN2_REG TASDEVICE_REG(0x00, 0x14, 0x44) + +#define TAS2781_TEST_UNLOCK_REG TASDEVICE_REG(0x00, 0xFD, 0x0D) +#define TAS2781_TEST_PAGE_UNLOCK 0x0D + +#define TAS2781_RUNTIME_LATCH_RE_REG TASDEVICE_REG(0x00, 0x00, 0x49) +#define TAS2781_RUNTIME_RE_REG_TF TASDEVICE_REG(0x64, 0x62, 0x48) +#define TAS2781_RUNTIME_RE_REG TASDEVICE_REG(0x64, 0x63, 0x44) + #define TASDEVICE_CMD_SING_W 0x1 #define TASDEVICE_CMD_BURST 0x2 #define TASDEVICE_CMD_DELAY 0x3 @@ -70,7 +117,15 @@ enum device_catlog_id { OTHERS }; +struct bulk_reg_val { + int reg; + unsigned char val[4]; + unsigned char val_len; + bool is_locked; +}; + struct tasdevice { + struct bulk_reg_val *cali_data_backup; struct tasdevice_fw *cali_data_fmw; unsigned int dev_addr; unsigned int err_code; @@ -81,9 +136,19 @@ struct tasdevice { bool is_loaderr; }; +struct cali_reg { + unsigned int r0_reg; + unsigned int r0_low_reg; + unsigned int invr0_reg; + unsigned int pow_reg; + unsigned int tlimit_reg; +}; + struct calidata { unsigned char *data; unsigned long total_sz; + struct cali_reg cali_reg_array; + unsigned int cali_dat_sz_per_dev; }; struct tasdevice_priv { @@ -119,6 +184,7 @@ struct tasdevice_priv { bool force_fwload_status; bool playback_started; bool isacpi; + bool is_user_space_calidata; unsigned int global_addr; int (*fw_parse_variable_header)(struct tasdevice_priv *tas_priv, @@ -145,6 +211,8 @@ int tasdevice_init(struct tasdevice_priv *tas_priv); void tasdevice_remove(struct tasdevice_priv *tas_priv); int tasdevice_save_calibration(struct tasdevice_priv *tas_priv); void tasdevice_apply_calibration(struct tasdevice_priv *tas_priv); +int tasdev_chn_switch(struct tasdevice_priv *tas_priv, + unsigned short chn); int tasdevice_dev_read(struct tasdevice_priv *tas_priv, unsigned short chn, unsigned int reg, unsigned int *value); int tasdevice_dev_write(struct tasdevice_priv *tas_priv, diff --git a/sound/soc/codecs/tas2781-comlib.c b/sound/soc/codecs/tas2781-comlib.c index 664c371796d6..1e0b3aa95749 100644 --- a/sound/soc/codecs/tas2781-comlib.c +++ b/sound/soc/codecs/tas2781-comlib.c @@ -88,6 +88,32 @@ static int tasdevice_change_chn_book(struct tasdevice_priv *tas_priv, return ret; } +int tasdev_chn_switch(struct tasdevice_priv *tas_priv, + unsigned short chn) +{ + struct i2c_client *client = (struct i2c_client *)tas_priv->client; + struct tasdevice *tasdev = &tas_priv->tasdevice[chn]; + struct regmap *map = tas_priv->regmap; + int ret; + + if (client->addr != tasdev->dev_addr) { + client->addr = tasdev->dev_addr; + /* All devices share the same regmap, clear the page + * inside regmap once switching to another device. + * Register 0 at any pages and any books inside tas2781 + * is the same one for page-switching. + */ + ret = regmap_write(map, TASDEVICE_PAGE_SELECT, 0); + if (ret < 0) { + dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret); + return ret; + } + return 1; + } + return 0; +} +EXPORT_SYMBOL_GPL(tasdev_chn_switch); + int tasdevice_dev_read(struct tasdevice_priv *tas_priv, unsigned short chn, unsigned int reg, unsigned int *val) { diff --git a/sound/soc/codecs/tas2781-fmwlib.c b/sound/soc/codecs/tas2781-fmwlib.c index f3a7605f0710..3de0132c345d 100644 --- a/sound/soc/codecs/tas2781-fmwlib.c +++ b/sound/soc/codecs/tas2781-fmwlib.c @@ -2151,20 +2151,61 @@ static int tasdevice_load_data(struct tasdevice_priv *tas_priv, static void tasdev_load_calibrated_data(struct tasdevice_priv *priv, int i) { + struct tasdevice_fw *cal_fmw = priv->tasdevice[i].cali_data_fmw; + struct calidata *cali_data = &priv->cali_data; + struct cali_reg *p = &cali_data->cali_reg_array; + unsigned char *data = cali_data->data; struct tasdevice_calibration *cal; - struct tasdevice_fw *cal_fmw; + int k = i * (cali_data->cali_dat_sz_per_dev + 1); + int rc; - cal_fmw = priv->tasdevice[i].cali_data_fmw; + /* Load the calibrated data from cal bin file */ + if (!priv->is_user_space_calidata && cal_fmw) { + cal = cal_fmw->calibrations; - /* No calibrated data for current devices, playback will go ahead. */ - if (!cal_fmw) + if (cal) + load_calib_data(priv, &cal->dev_data); return; - - cal = cal_fmw->calibrations; - if (!cal) + } + if (!priv->is_user_space_calidata) + return; + /* load calibrated data from user space */ + if (data[k] != i) { + dev_err(priv->dev, "%s: no cal-data for dev %d from usr-spc\n", + __func__, i); return; + } + k++; - load_calib_data(priv, &cal->dev_data); + rc = tasdevice_dev_bulk_write(priv, i, p->r0_reg, &(data[k]), 4); + if (rc < 0) { + dev_err(priv->dev, "chn %d r0_reg bulk_wr err = %d\n", i, rc); + return; + } + k += 4; + rc = tasdevice_dev_bulk_write(priv, i, p->r0_low_reg, &(data[k]), 4); + if (rc < 0) { + dev_err(priv->dev, "chn %d r0_low_reg err = %d\n", i, rc); + return; + } + k += 4; + rc = tasdevice_dev_bulk_write(priv, i, p->invr0_reg, &(data[k]), 4); + if (rc < 0) { + dev_err(priv->dev, "chn %d invr0_reg err = %d\n", i, rc); + return; + } + k += 4; + rc = tasdevice_dev_bulk_write(priv, i, p->pow_reg, &(data[k]), 4); + if (rc < 0) { + dev_err(priv->dev, "chn %d pow_reg bulk_wr err = %d\n", i, rc); + return; + } + k += 4; + rc = tasdevice_dev_bulk_write(priv, i, p->tlimit_reg, &(data[k]), 4); + if (rc < 0) { + dev_err(priv->dev, "chn %d tlimit_reg err = %d\n", i, rc); + return; + } } int tasdevice_select_tuningprm_cfg(void *context, int prm_no, @@ -2259,9 +2300,10 @@ int tasdevice_select_tuningprm_cfg(void *context, int prm_no, tas_priv->tasdevice[i].cur_conf = cfg_no; } } - } else + } else { dev_dbg(tas_priv->dev, "%s: Unneeded loading dsp conf %d\n", __func__, cfg_no); + } status |= cfg_info[rca_conf_no]->active_dev; diff --git a/sound/soc/codecs/tas2781-i2c.c b/sound/soc/codecs/tas2781-i2c.c index 59fcce7fef7b..ebd71c7eaa59 100644 --- a/sound/soc/codecs/tas2781-i2c.c +++ b/sound/soc/codecs/tas2781-i2c.c @@ -33,6 +33,143 @@ #include <sound/tas2781-tlv.h> #include <asm/unaligned.h> +static const struct bulk_reg_val tas2563_cali_start_reg[] = { + { + .reg = TAS2563_IDLE, + .val_len = 1, + .val = { 0x00 }, + }, + { + .reg = TAS2563_PRM_ENFF_REG, + .val_len = 4, + .val = { 0x40, 0x00, 0x00, 0x00 }, + }, + { + .reg = TAS2563_PRM_DISTCK_REG, + .val_len = 4, + .val = { 0x40, 0x00, 0x00, 0x00 }, + }, + { + .reg = TAS2563_PRM_TE_SCTHR_REG, + .val_len = 4, + .val = { 0x7f, 0xff, 0xff, 0xff }, + }, + { + .reg = TAS2563_PRM_PLT_FLAG_REG, + .val_len = 4, + .val = { 0x40, 0x00, 0x00, 0x00 }, + }, + { + .reg = TAS2563_PRM_SINEGAIN_REG, + .val_len = 4, + .val = { 0x0a, 0x3d, 0x70, 0xa4 }, + }, + { + .reg = TAS2563_TE_TA1_REG, + .val_len = 4, + .val = { 0x00, 0x36, 0x91, 0x5e }, + }, + { + .reg = TAS2563_TE_TA1_AT_REG, + .val_len = 4, + .val = { 0x00, 0x36, 0x91, 0x5e }, + }, + { + .reg = TAS2563_TE_TA2_REG, + .val_len = 4, + .val = { 0x00, 0x06, 0xd3, 0x72 }, + }, + { + .reg = TAS2563_TE_AT_REG, + .val_len = 4, + .val = { 0x00, 0x36, 0x91, 0x5e }, + }, + { + .reg = TAS2563_TE_DT_REG, + .val_len = 4, + .val = { 0x00, 0x36, 0x91, 0x5e }, + }, +}; + +static const struct bulk_reg_val tas2781_cali_start_reg[] = { + { + .reg = TAS2781_PRM_INT_MASK_REG, + .val = { 0xfe }, + .val_len = 1, + .is_locked = false + }, + { + .reg = TAS2781_PRM_CLK_CFG_REG, + .val = { 0xdd }, + .val_len = 1, + .is_locked = false + }, + { + .reg = TAS2781_PRM_RSVD_REG, + .val = { 0x20 }, + .val_len = 1, + .is_locked = false + }, + { + .reg = TAS2781_PRM_TEST_57_REG, + .val = { 0x14 }, + .val_len = 1, + .is_locked = true + }, + { + .reg = TAS2781_PRM_TEST_62_REG, + .val = { 0x45 }, + .val_len = 1, + .is_locked = true + }, + { + .reg = TAS2781_PRM_PVDD_UVLO_REG, + .val = { 0x03 }, + .val_len = 1, + .is_locked = false + }, + { + .reg = TAS2781_PRM_CHNL_0_REG, + .val = { 0xA8 }, + .val_len = 1, + .is_locked = false + }, + { + .reg = TAS2781_PRM_NG_CFG0_REG, + .val = { 0xb9 }, + .val_len = 1, + .is_locked = false + }, + { + .reg = TAS2781_PRM_IDLE_CH_DET_REG, + .val = { 0x92 }, + .val_len = 1, + .is_locked = false + }, + { + .reg = 0, + .val = { 0x00, 0x00, 0x00, 0x56 }, // 1mA + .val_len = 4, + .is_locked = false + }, + { + .reg = TAS2781_PRM_PLT_FLAG_REG, + .val = { 0x40, 0x00, 0x00, 0x00 }, + .val_len = 4, + .is_locked = false + }, + { + .reg = TAS2781_PRM_SINEGAIN_REG, + .val_len = 4, + .is_locked = false + }, + { + .reg = TAS2781_PRM_SINEGAIN2_REG, + .val_len = 4, + .is_locked = false + }, +}; + static const struct i2c_device_id tasdevice_id[] = { { "tas2563", TAS2563 }, { "tas2781", TAS2781 }, @@ -141,6 +278,556 @@ static int tasdev_force_fwload_put(struct snd_kcontrol *kcontrol, return change; } +static int tasdev_cali_data_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *priv = snd_soc_component_get_drvdata(comp); + struct soc_bytes_ext *bytes_ext = + (struct soc_bytes_ext *) kcontrol->private_value; + struct calidata *cali_data = &priv->cali_data; + struct cali_reg *p = &cali_data->cali_reg_array; + unsigned char *dst = ucontrol->value.bytes.data; + unsigned char *data = cali_data->data; + unsigned int i = 0; + unsigned int j, k; + int rc; + + guard(mutex)(&priv->codec_lock); + if (!priv->is_user_space_calidata) + return -1; + + if (!p->r0_reg) + return -1; + + dst[i++] = bytes_ext->max; + dst[i++] = 'r'; + + dst[i++] = TASDEVICE_BOOK_ID(p->r0_reg); + dst[i++] = TASDEVICE_PAGE_ID(p->r0_reg); + dst[i++] = TASDEVICE_PAGE_REG(p->r0_reg); + + dst[i++] = TASDEVICE_BOOK_ID(p->r0_low_reg); + dst[i++] = TASDEVICE_PAGE_ID(p->r0_low_reg); + dst[i++] = TASDEVICE_PAGE_REG(p->r0_low_reg); + + dst[i++] = TASDEVICE_BOOK_ID(p->invr0_reg); + dst[i++] = TASDEVICE_PAGE_ID(p->invr0_reg); + dst[i++] = TASDEVICE_PAGE_REG(p->invr0_reg); + + dst[i++] = TASDEVICE_BOOK_ID(p->pow_reg); + dst[i++] = TASDEVICE_PAGE_ID(p->pow_reg); + dst[i++] = TASDEVICE_PAGE_REG(p->pow_reg); + + dst[i++] = TASDEVICE_BOOK_ID(p->tlimit_reg); + dst[i++] = TASDEVICE_PAGE_ID(p->tlimit_reg); + dst[i++] = TASDEVICE_PAGE_REG(p->tlimit_reg); + + for (j = 0, k = 0; j < priv->ndev; j++) { + if (j == data[k]) { + dst[i++] = j; + k++; + } else { + dev_err(priv->dev, "chn %d device %u not match\n", + j, data[k]); + k += 21; + continue; + } + rc = tasdevice_dev_bulk_read(priv, j, p->r0_reg, &dst[i], 4); + if (rc < 0) { + dev_err(priv->dev, "chn %d r0_reg bulk_rd err = %d\n", + j, rc); + i += 20; + k += 20; + continue; + } + rc = memcmp(&dst[i], &data[k], 4); + if (rc != 0) + dev_dbg(priv->dev, "chn %d r0_data is not same\n", j); + k += 4; + i += 4; + rc = tasdevice_dev_bulk_read(priv, j, p->r0_low_reg, + &dst[i], 4); + if (rc < 0) { + dev_err(priv->dev, "chn %d r0_low bulk_rd err = %d\n", + j, rc); + i += 16; + k += 16; + continue; + } + rc = memcmp(&dst[i], &data[k], 4); + if (rc != 0) + dev_dbg(priv->dev, "chn %d r0_low is not same\n", j); + i += 4; + k += 4; + rc = tasdevice_dev_bulk_read(priv, j, p->invr0_reg, + &dst[i], 4); + if (rc < 0) { + dev_err(priv->dev, "chn %d invr0 bulk_rd err = %d\n", + j, rc); + i += 12; + k += 12; + continue; + } + rc = memcmp(&dst[i], &data[k], 4); + if (rc != 0) + dev_dbg(priv->dev, "chn %d invr0 is not same\n", j); + i += 4; + k += 4; + rc = tasdevice_dev_bulk_read(priv, j, p->pow_reg, &dst[i], 4); + if (rc < 0) { + dev_err(priv->dev, "chn %d pow_reg bulk_rd err = %d\n", + j, rc); + i += 8; + k += 8; + continue; + } + rc = memcmp(&dst[i], &data[k], 4); + if (rc != 0) + dev_dbg(priv->dev, "chn %d pow_reg is not same\n", j); + i += 4; + k += 4; + rc = tasdevice_dev_bulk_read(priv, j, p->tlimit_reg, + &dst[i], 4); + if (rc < 0) { + dev_err(priv->dev, "chn %d tlimit bulk_rd err = %d\n", + j, rc); + } + rc = memcmp(&dst[i], &data[k], 4); + if (rc != 0) + dev_dbg(priv->dev, "chn %d tlimit is not same\n", j); + i += 4; + k += 4; + } + return 0; +} + +static int calib_data_get(struct tasdevice_priv *tas_priv, int reg, + unsigned char *dst) +{ + struct i2c_client *clt = (struct i2c_client *)tas_priv->client; + struct tasdevice *tasdev = tas_priv->tasdevice; + int rc = -1; + int i; + + for (i = 0; i < tas_priv->ndev; i++) { + if (clt->addr == tasdev[i].dev_addr) { + /* First byte is the device index. */ + dst[0] = i; + rc = tasdevice_dev_bulk_read(tas_priv, i, reg, &dst[1], + 4); + break; + } + } + + return rc; +} + +static void sngl_calib_start(struct tasdevice_priv *tas_priv, int i, + int *reg, unsigned char *dat) +{ + struct tasdevice *tasdev = tas_priv->tasdevice; + struct bulk_reg_val *p = tasdev[i].cali_data_backup; + const int sum = ARRAY_SIZE(tas2781_cali_start_reg); + int j; + + if (p == NULL) + return; + + /* Store the current setting from the chip */ + for (j = 0; j < sum; j++) { + if (p[j].val_len == 1) { + if (p[j].is_locked) + tasdevice_dev_write(tas_priv, i, + TAS2781_TEST_UNLOCK_REG, + TAS2781_TEST_PAGE_UNLOCK); + tasdevice_dev_read(tas_priv, i, p[j].reg, + (int *)&p[j].val[0]); + } else { + switch (p[j].reg) { + case 0: + if (!reg[0]) + continue; + p[j].reg = reg[0]; + break; + case TAS2781_PRM_PLT_FLAG_REG: + p[j].reg = reg[1]; + break; + case TAS2781_PRM_SINEGAIN_REG: + p[j].reg = reg[2]; + break; + case TAS2781_PRM_SINEGAIN2_REG: + p[j].reg = reg[3]; + break; + } + tasdevice_dev_bulk_read(tas_priv, i, p[j].reg, + p[j].val, 4); + } + } + + /* Update the setting for calibration */ + for (j = 0; j < sum - 2; j++) { + if (p[j].val_len == 1) { + if (p[j].is_locked) + tasdevice_dev_write(tas_priv, i, + TAS2781_TEST_UNLOCK_REG, + TAS2781_TEST_PAGE_UNLOCK); + tasdevice_dev_write(tas_priv, i, p[j].reg, + tas2781_cali_start_reg[j].val[0]); + } else { + if (!p[j].reg) + continue; + tasdevice_dev_bulk_write(tas_priv, i, p[j].reg, + (unsigned char *) + tas2781_cali_start_reg[j].val, 4); + } + } + + tasdevice_dev_bulk_write(tas_priv, i, p[j].reg, &dat[1], 4); + tasdevice_dev_bulk_write(tas_priv, i, p[j + 1].reg, &dat[5], 4); +} + +static int tas2781_calib_start_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *priv = snd_soc_component_get_drvdata(comp); + struct soc_bytes_ext *bytes_ext = + (struct soc_bytes_ext *) kcontrol->private_value; + unsigned char *dat = ucontrol->value.bytes.data; + int i, reg[4]; + int j = 0; + + guard(mutex)(&priv->codec_lock); + if (priv->chip_id != TAS2781 || bytes_ext->max != dat[0] || + dat[1] != 'r') { + dev_err(priv->dev, "%s: package fmt or chipid incorrect\n", + __func__); + return 0; + } + j += 2; + /* refresh pilot tone and SineGain register */ + for (i = 0; i < ARRAY_SIZE(reg); i++) { + reg[i] = TASDEVICE_REG(dat[j], dat[j + 1], dat[j + 2]); + j += 3; + } + + for (i = 0; i < priv->ndev; i++) { + int k = i * 9 + j; + + if (dat[k] != i) { + dev_err(priv->dev, "%s:no cal-setting for dev %d\n", + __func__, i); + continue; + } + sngl_calib_start(priv, i, reg, dat + k); + } + return 1; +} + +static void tas2781_calib_stop_put(struct tasdevice_priv *tas_priv) +{ + const int sum = ARRAY_SIZE(tas2781_cali_start_reg); + int i, j; + + for (i = 0; i < tas_priv->ndev; i++) { + struct tasdevice *tasdev = tas_priv->tasdevice; + struct bulk_reg_val *p = tasdev[i].cali_data_backup; + + if (p == NULL) + continue; + + for (j = 0; j < sum; j++) { + if (p[j].val_len == 1) { + if (p[j].is_locked) + tasdevice_dev_write(tas_priv, i, + TAS2781_TEST_UNLOCK_REG, + TAS2781_TEST_PAGE_UNLOCK); + tasdevice_dev_write(tas_priv, i, p[j].reg, + p[j].val[0]); + } else { + if (!p[j].reg) + continue; + tasdevice_dev_bulk_write(tas_priv, i, p[j].reg, + p[j].val, 4); + } + } + } +} + +static int tas2563_calib_start_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct bulk_reg_val *q = (struct bulk_reg_val *)tas2563_cali_start_reg; + struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(comp); + const int sum = ARRAY_SIZE(tas2563_cali_start_reg); + int rc = 1; + int i, j; + + guard(mutex)(&tas_priv->codec_lock); + if (tas_priv->chip_id != TAS2563) { + rc = -1; + goto out; + } + + for (i = 0; i < tas_priv->ndev; i++) { + struct tasdevice *tasdev = tas_priv->tasdevice; + struct bulk_reg_val *p = tasdev[i].cali_data_backup; + + if (p == NULL) + continue; + for (j = 0; j < sum; j++) { + if (p[j].val_len == 1) + tasdevice_dev_read(tas_priv, + i, p[j].reg, + (unsigned int *)&p[j].val[0]); + else + tasdevice_dev_bulk_read(tas_priv, + i, p[j].reg, p[j].val, 4); + } + + for (j = 0; j < sum; j++) { + if (p[j].val_len == 1) + tasdevice_dev_write(tas_priv, i, p[j].reg, + q[j].val[0]); + else + tasdevice_dev_bulk_write(tas_priv, i, p[j].reg, + q[j].val, 4); + } + } +out: + return rc; +} + +static void tas2563_calib_stop_put(struct tasdevice_priv *tas_priv) +{ + const int sum = ARRAY_SIZE(tas2563_cali_start_reg); + int i, j; + + for (i = 0; i < tas_priv->ndev; i++) { + struct tasdevice *tasdev = tas_priv->tasdevice; + struct bulk_reg_val *p = tasdev[i].cali_data_backup; + + if (p == NULL) + continue; + + for (j = 0; j < sum; j++) { + if (p[j].val_len == 1) + tasdevice_dev_write(tas_priv, i, p[j].reg, + p[j].val[0]); + else + tasdevice_dev_bulk_write(tas_priv, i, p[j].reg, + p[j].val, 4); + } + } +} + +static int tasdev_calib_stop_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *priv = snd_soc_component_get_drvdata(comp); + + guard(mutex)(&priv->codec_lock); + if (priv->chip_id == TAS2563) + tas2563_calib_stop_put(priv); + else + tas2781_calib_stop_put(priv); + + return 1; +} + +static int tasdev_cali_data_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *priv = snd_soc_component_get_drvdata(comp); + struct soc_bytes_ext *bytes_ext = + (struct soc_bytes_ext *) kcontrol->private_value; + struct calidata *cali_data = &priv->cali_data; + struct cali_reg *p = &cali_data->cali_reg_array; + unsigned char *src = ucontrol->value.bytes.data; + unsigned char *dst = cali_data->data; + int rc = 1, i = 0; + int j; + + guard(mutex)(&priv->codec_lock); + if (src[0] != bytes_ext->max || src[1] != 'r') { + dev_err(priv->dev, "%s: pkg fmt invalid\n", __func__); + return 0; + } + for (j = 0; j < priv->ndev; j++) { + if (src[17 + j * 21] != j) { + dev_err(priv->dev, "%s: pkg fmt invalid\n", __func__); + return 0; + } + } + i += 2; + priv->is_user_space_calidata = true; + + p->r0_reg = TASDEVICE_REG(src[i], src[i + 1], src[i + 2]); + i += 3; + p->r0_low_reg = TASDEVICE_REG(src[i], src[i + 1], src[i + 2]); + i += 3; + p->invr0_reg = TASDEVICE_REG(src[i], src[i + 1], src[i + 2]); + i += 3; + p->pow_reg = TASDEVICE_REG(src[i], src[i + 1], src[i + 2]); + i += 3; + p->tlimit_reg = TASDEVICE_REG(src[i], src[i + 1], src[i + 2]); + i += 3; + + memcpy(dst, &src[i], cali_data->total_sz); + return rc; +} + +static int tas2781_latch_reg_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(comp); + struct i2c_client *clt = (struct i2c_client *)tas_priv->client; + struct soc_bytes_ext *bytes_ext = + (struct soc_bytes_ext *) kcontrol->private_value; + struct tasdevice *tasdev = tas_priv->tasdevice; + unsigned char *dst = ucontrol->value.bytes.data; + int i, val, rc = -1; + + dst[0] = bytes_ext->max; + guard(mutex)(&tas_priv->codec_lock); + for (i = 0; i < tas_priv->ndev; i++) { + if (clt->addr == tasdev[i].dev_addr) { + /* First byte is the device index. */ + dst[1] = i; + rc = tasdevice_dev_read(tas_priv, i, + TAS2781_RUNTIME_LATCH_RE_REG, &val); + if (rc < 0) + dev_err(tas_priv->dev, "%s, get value error\n", + __func__); + else + dst[2] = val; + + break; + } + } + + return rc; +} + +static int tasdev_tf_data_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(comp); + struct soc_bytes_ext *bytes_ext = + (struct soc_bytes_ext *) kcontrol->private_value; + unsigned char *dst = ucontrol->value.bytes.data; + unsigned int reg; + int rc = -1; + + if (tas_priv->chip_id == TAS2781) + reg = TAS2781_RUNTIME_RE_REG_TF; + else + reg = TAS2563_RUNTIME_RE_REG_TF; + + guard(mutex)(&tas_priv->codec_lock); + dst[0] = bytes_ext->max; + rc = calib_data_get(tas_priv, reg, &dst[1]); + + return rc; +} + +static int tasdev_re_data_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(comp); + struct soc_bytes_ext *bytes_ext = + (struct soc_bytes_ext *) kcontrol->private_value; + unsigned char *dst = ucontrol->value.bytes.data; + unsigned int reg; + int rc = -1; + + if (tas_priv->chip_id == TAS2781) + reg = TAS2781_RUNTIME_RE_REG; + else + reg = TAS2563_RUNTIME_RE_REG; + guard(mutex)(&tas_priv->codec_lock); + dst[0] = bytes_ext->max; + rc = calib_data_get(tas_priv, reg, &dst[1]); + + return rc; +} + +static int tasdev_r0_data_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(comp); + struct calidata *cali_data = &tas_priv->cali_data; + struct soc_bytes_ext *bytes_ext = + (struct soc_bytes_ext *) kcontrol->private_value; + unsigned char *dst = ucontrol->value.bytes.data; + unsigned int reg; + int rc = -1; + + guard(mutex)(&tas_priv->codec_lock); + + if (tas_priv->chip_id == TAS2563) + reg = TAS2563_PRM_R0_REG; + else if (cali_data->cali_reg_array.r0_reg) + reg = cali_data->cali_reg_array.r0_reg; + else + return -1; + dst[0] = bytes_ext->max; + rc = calib_data_get(tas_priv, reg, &dst[1]); + + return rc; +} + +static int tasdev_XMA1_data_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(comp); + struct soc_bytes_ext *bytes_ext = + (struct soc_bytes_ext *) kcontrol->private_value; + unsigned char *dst = ucontrol->value.bytes.data; + unsigned int reg = TASDEVICE_XM_A1_REG; + int rc = -1; + + guard(mutex)(&tas_priv->codec_lock); + dst[0] = bytes_ext->max; + rc = calib_data_get(tas_priv, reg, &dst[1]); + + return rc; +} + +static int tasdev_XMA2_data_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(comp); + struct soc_bytes_ext *bytes_ext = + (struct soc_bytes_ext *) kcontrol->private_value; + unsigned char *dst = ucontrol->value.bytes.data; + unsigned int reg = TASDEVICE_XM_A2_REG; + int rc = -1; + + guard(mutex)(&tas_priv->codec_lock); + dst[0] = bytes_ext->max; + rc = calib_data_get(tas_priv, reg, &dst[1]); + + return rc; +} + +static int tasdev_nop_get( + struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + return 0; +} + static int tas2563_digital_gain_get( struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol) @@ -241,6 +928,16 @@ static const struct snd_kcontrol_new tasdevice_snd_controls[] = { tasdev_force_fwload_get, tasdev_force_fwload_put), }; +static const struct snd_kcontrol_new tasdevice_cali_controls[] = { + SOC_SINGLE_EXT("Calibration Stop", SND_SOC_NOPM, 0, 1, 0, + tasdev_nop_get, tasdev_calib_stop_put), + SND_SOC_BYTES_EXT("Amp TF Data", 6, tasdev_tf_data_get, NULL), + SND_SOC_BYTES_EXT("Amp RE Data", 6, tasdev_re_data_get, NULL), + SND_SOC_BYTES_EXT("Amp R0 Data", 6, tasdev_r0_data_get, NULL), + SND_SOC_BYTES_EXT("Amp XMA1 Data", 6, tasdev_XMA1_data_get, NULL), + SND_SOC_BYTES_EXT("Amp XMA2 Data", 6, tasdev_XMA2_data_get, NULL), +}; + static const struct snd_kcontrol_new tas2781_snd_controls[] = { SOC_SINGLE_RANGE_EXT_TLV("Speaker Analog Gain", TAS2781_AMP_LEVEL, 1, 0, 20, 0, tas2781_amp_getvol, @@ -250,6 +947,10 @@ static const struct snd_kcontrol_new tas2781_snd_controls[] = { tas2781_digital_putvol, dvc_tlv), }; +static const struct snd_kcontrol_new tas2781_cali_controls[] = { + SND_SOC_BYTES_EXT("Amp Latch Data", 3, tas2781_latch_reg_get, NULL), +}; + static const struct snd_kcontrol_new tas2563_snd_controls[] = { SOC_SINGLE_RANGE_EXT_TLV("Speaker Digital Volume", TAS2563_DVC_LVL, 0, 0, ARRAY_SIZE(tas2563_dvc_table) - 1, 0, @@ -257,6 +958,11 @@ static const struct snd_kcontrol_new tas2563_snd_controls[] = { tas2563_dvc_tlv), }; +static const struct snd_kcontrol_new tas2563_cali_controls[] = { + SOC_SINGLE_EXT("Calibration Start", SND_SOC_NOPM, 0, 1, 0, + tasdev_nop_get, tas2563_calib_start_put), +}; + static int tasdevice_set_profile_id(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol) { @@ -274,6 +980,31 @@ static int tasdevice_set_profile_id(struct snd_kcontrol *kcontrol, return ret; } +static int tasdevice_info_active_num(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = 1; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = tas_priv->ndev - 1; + + return 0; +} + +static int tasdevice_info_chip_id(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = 1; + uinfo->value.integer.min = TAS2563; + uinfo->value.integer.max = TAS2781; + + return 0; +} + static int tasdevice_info_programs(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_info *uinfo) { @@ -330,6 +1061,17 @@ static int tasdevice_get_profile_id(struct snd_kcontrol *kcontrol, return 0; } +static int tasdevice_get_chip_id(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + + ucontrol->value.integer.value[0] = tas_priv->chip_id; + + return 0; +} + static int tasdevice_create_control(struct tasdevice_priv *tas_priv) { struct snd_kcontrol_new *prof_ctrls; @@ -421,11 +1163,47 @@ static int tasdevice_configuration_put( return ret; } +static int tasdevice_active_num_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + struct i2c_client *clt = (struct i2c_client *)tas_priv->client; + struct tasdevice *tasdev = tas_priv->tasdevice; + int i; + + for (i = 0; i < tas_priv->ndev; i++) { + if (clt->addr == tasdev[i].dev_addr) { + ucontrol->value.integer.value[0] = i; + return 0; + } + } + + return -1; +} + +static int tasdevice_active_num_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *codec = snd_soc_kcontrol_component(kcontrol); + struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(codec); + int dev_id = ucontrol->value.integer.value[0]; + int max = tas_priv->ndev - 1, rc; + + dev_id = clamp(dev_id, 0, max); + + guard(mutex)(&tas_priv->codec_lock); + rc = tasdev_chn_switch(tas_priv, dev_id); + + return rc; +} + static int tasdevice_dsp_create_ctrls(struct tasdevice_priv *tas_priv) { struct snd_kcontrol_new *dsp_ctrls; - char *prog_name, *conf_name; - int nr_controls = 2; + char *active_dev_num, *chip_id; + char *conf_name, *prog_name; + int nr_controls = 4; int mix_index = 0; int ret; @@ -466,6 +1244,30 @@ static int tasdevice_dsp_create_ctrls(struct tasdevice_priv *tas_priv) dsp_ctrls[mix_index].put = tasdevice_configuration_put; mix_index++; + active_dev_num = devm_kstrdup(tas_priv->dev, "Activate Tasdevice Num", + GFP_KERNEL); + if (!active_dev_num) { + ret = -ENOMEM; + goto out; + } + dsp_ctrls[mix_index].name = active_dev_num; + dsp_ctrls[mix_index].iface = SNDRV_CTL_ELEM_IFACE_MIXER; + dsp_ctrls[mix_index].info = tasdevice_info_active_num; + dsp_ctrls[mix_index].get = tasdevice_active_num_get; + dsp_ctrls[mix_index].put = tasdevice_active_num_put; + mix_index++; + + chip_id = devm_kstrdup(tas_priv->dev, "Tasdevice Chip Id", GFP_KERNEL); + if (!chip_id) { + ret = -ENOMEM; + goto out; + } + dsp_ctrls[mix_index].name = chip_id; + dsp_ctrls[mix_index].iface = SNDRV_CTL_ELEM_IFACE_MIXER; + dsp_ctrls[mix_index].info = tasdevice_info_chip_id; + dsp_ctrls[mix_index].get = tasdevice_get_chip_id; + mix_index++; + ret = snd_soc_add_component_controls(tas_priv->codec, dsp_ctrls, nr_controls < mix_index ? nr_controls : mix_index); @@ -473,6 +1275,150 @@ static int tasdevice_dsp_create_ctrls(struct tasdevice_priv *tas_priv) return ret; } +static int tasdevice_create_cali_ctrls(struct tasdevice_priv *tas_priv) +{ + struct calidata *cali_data = &tas_priv->cali_data; + struct tasdevice *tasdev = tas_priv->tasdevice; + struct soc_bytes_ext *ext_cali_data; + struct snd_kcontrol_new *cali_ctrls; + unsigned int num_controls; + char *cali_name; + int rc, i; + + rc = snd_soc_add_component_controls(tas_priv->codec, + tasdevice_cali_controls, ARRAY_SIZE(tasdevice_cali_controls)); + if (rc < 0) { + dev_err(tas_priv->dev, "%s: Add cali controls err rc = %d", + __func__, rc); + return rc; + } + + if (tas_priv->chip_id == TAS2781) { + cali_ctrls = (struct snd_kcontrol_new *)tas2781_cali_controls; + num_controls = ARRAY_SIZE(tas2781_cali_controls); + for (i = 0; i < tas_priv->ndev; i++) { + tasdev[i].cali_data_backup = + kmemdup(tas2781_cali_start_reg, + sizeof(tas2781_cali_start_reg), GFP_KERNEL); + if (!tasdev[i].cali_data_backup) + return -ENOMEM; + } + } else { + cali_ctrls = (struct snd_kcontrol_new *)tas2563_cali_controls; + num_controls = ARRAY_SIZE(tas2563_cali_controls); + for (i = 0; i < tas_priv->ndev; i++) { + tasdev[i].cali_data_backup = + kmemdup(tas2563_cali_start_reg, + sizeof(tas2563_cali_start_reg), GFP_KERNEL); + if (!tasdev[i].cali_data_backup) + return -ENOMEM; + } + } + + rc = snd_soc_add_component_controls(tas_priv->codec, cali_ctrls, + num_controls); + if (rc < 0) { + dev_err(tas_priv->dev, "%s: Add chip cali ctrls err rc = %d", + __func__, rc); + return rc; + } + + /* index for cali_ctrls */ + i = 0; + if (tas_priv->chip_id == TAS2781) + num_controls = 2; + else + num_controls = 1; + + /* + * Alloc kcontrol via devm_kzalloc, which don't manually + * free the kcontrol + */ + cali_ctrls = devm_kcalloc(tas_priv->dev, num_controls, + sizeof(cali_ctrls[0]), GFP_KERNEL); + if (!cali_ctrls) + return -ENOMEM; + + ext_cali_data = devm_kzalloc(tas_priv->dev, sizeof(*ext_cali_data), + GFP_KERNEL); + if (!ext_cali_data) + return -ENOMEM; + + cali_name = devm_kstrdup(tas_priv->dev, "Speaker Calibrated Data", + GFP_KERNEL); + if (!cali_name) + return -ENOMEM; + /* the number of calibrated data per tas2563/tas2781 */ + cali_data->cali_dat_sz_per_dev = 20; + /* + * Data structure for tas2563/tas2781 calibrated data: + * Pkg len (1 byte) + * Reg id (1 byte, constant 'r') + * book, page, register array for calibrated data (15 bytes) + * for (i = 0; i < Device-Sum; i++) { + * Device #i index_info (1 byte) + * Calibrated data for Device #i (20 bytes) + * } + */ + ext_cali_data->max = tas_priv->ndev * + (cali_data->cali_dat_sz_per_dev + 1) + 1 + 15 + 1; + tas_priv->cali_data.total_sz = tas_priv->ndev * + (cali_data->cali_dat_sz_per_dev + 1); + tas_priv->cali_data.data = devm_kzalloc(tas_priv->dev, + ext_cali_data->max, GFP_KERNEL); + cali_ctrls[i].name = cali_name; + cali_ctrls[i].iface = SNDRV_CTL_ELEM_IFACE_MIXER; + cali_ctrls[i].info = snd_soc_bytes_info_ext; + cali_ctrls[i].get = tasdev_cali_data_get; + cali_ctrls[i].put = tasdev_cali_data_put; + cali_ctrls[i].private_value = (unsigned long)ext_cali_data; + i++; + + cali_data->data = devm_kzalloc(tas_priv->dev, cali_data->total_sz, + GFP_KERNEL); + if (!cali_data->data) + return -ENOMEM; + + if (tas_priv->chip_id == TAS2781) { + struct soc_bytes_ext *ext_cali_start; + char *cali_start_name; + + ext_cali_start = devm_kzalloc(tas_priv->dev, + sizeof(*ext_cali_start), GFP_KERNEL); + if (!ext_cali_start) + return -ENOMEM; + + cali_start_name = devm_kstrdup(tas_priv->dev, + "Calibration Start", GFP_KERNEL); + if (!cali_start_name) + return -ENOMEM; + /* + * package structure for tas2781 ftc start: + * Pkg len (1 byte) + * Reg id (1 byte, constant 'r') + * book, page, register for pilot threshold, pilot tone + * and sine gain (12 bytes) + * for (i = 0; i < Device-Sum; i++) { + * Device #i index_info (1 byte) + * Sine gain for Device #i (8 bytes) + * } + */ + ext_cali_data->max = 14 + tas_priv->ndev * 9; + cali_ctrls[i].name = cali_start_name; + cali_ctrls[i].iface = SNDRV_CTL_ELEM_IFACE_MIXER; + cali_ctrls[i].info = snd_soc_bytes_info_ext; + cali_ctrls[i].put = tas2781_calib_start_put; + cali_ctrls[i].get = tasdev_nop_get; + cali_ctrls[i].private_value = (unsigned long)ext_cali_start; + i++; + } + + rc = snd_soc_add_component_controls(tas_priv->codec, cali_ctrls, + num_controls < i ? num_controls : i); + + return rc; +} + static void tasdevice_fw_ready(const struct firmware *fmw, void *context) { @@ -519,6 +1465,12 @@ static void tasdevice_fw_ready(const struct firmware *fmw, goto out; } + ret = tasdevice_create_cali_ctrls(tas_priv); + if (ret) { + dev_err(tas_priv->dev, "cali controls error\n"); + goto out; + } + tas_priv->fw_state = TASDEVICE_DSP_FW_ALL_OK; /* If calibrated data occurs error, dsp will still works with default @@ -720,6 +1672,11 @@ static int tasdevice_codec_probe(struct snd_soc_component *codec) static void tasdevice_deinit(void *context) { struct tasdevice_priv *tas_priv = (struct tasdevice_priv *) context; + struct tasdevice *tasdev = tas_priv->tasdevice; + int i; + + for (i = 0; i < tas_priv->ndev; i++) + kfree(tasdev[i].cali_data_backup); tasdevice_config_info_remove(tas_priv); tasdevice_dsp_remove(tas_priv); -- 2.35.7

3 2