- Alsa-devel - mailman.alsa-project.org

[alsa-devel] Software mixing according to priority of streams
by Nobin Mathew 15 Jun '07

15 Jun '07

Hi, Is there any sound mixer which does mixing according to priority of streams, i.e. i will have streams with different priority like audio stream , bluettoth sco stream, gps navigation sound stream etc. Since my hardware will not support hardware mixing i will have to do this mixing in software. If bluetooth sco stream is opened while audio stream is playing then the application (sound server) should stop the playback of audio stream and should start playback of bletooth sco stream. priority order is bluettoth sco > gps navigation sound > audio Can dmix and Jack server the purpose. Nobin Mathew

3 8

[alsa-devel] [RFC][ASoC] New device/driver arch
by Liam Girdwood 15 Jun '07

15 Jun '07

I'd like to gather some feedback on some changes I've been making to ASoC recently. The changes were made to fit in better with the PPC device tree and to help with easier porting to new platforms. They were also introduced to make dealing with device probe errors (e.g. I2C probe failure) a little easier. The largest change is the introduction of an ASoC bus device. All component drivers (that is, codec, codec DAI, CPU DAI, and DMA PCM drivers) register with this bus. This should simplify device registration and hopefully better fit in with the PPC model. A component driver now typically consists of the standard driver ops and a set of ASoC/ALSA ops to configure audio. The new soc.h shows this here :- http://opensource.wolfsonmicro.com/cgi-bin/gitweb/gitweb.cgi?p=linux-2.6-as… Example component drivers are here :- I2S http://opensource.wolfsonmicro.com/cgi-bin/gitweb/gitweb.cgi?p=linux-2.6-as… DMA http://opensource.wolfsonmicro.com/cgi-bin/gitweb/gitweb.cgi?p=linux-2.6-as… WM8753 Codec http://opensource.wolfsonmicro.com/cgi-bin/gitweb/gitweb.cgi?p=linux-2.6-as… Another major change is that there is no more snd_dai_link (structure that connected codec <--> CPU). This has been replaced by an ASoC PCM device that describes each PCM device in the machine. This new ASoC PCM device has it's own driver and registers with the bus (like the others). This allows an ASoC PCM driver to be defined like :- static struct snd_soc_device_driver hifi_pcm_drv = { .type = SND_SOC_BUS_TYPE_PCM, .driver = { .name = "mainstone-hifi-pcm", .owner = THIS_MODULE, .probe = hifi_pcm_probe, .remove = hifi_pcm_remove, }, .components = { .cpu_dai = pxa2xx_i2s, .codec = wm8753_codec, .codec_dai = wm8753_hifi_dai, .platform = pxa2xx_pcm, }, }; This now shows each component within the driver structure. The snd_soc_machine driver has changed and can now contain numerous ASoC PCM devices. It is now a platform driver. Example machine driver for Mainstone with WM8753 is here :- http://opensource.wolfsonmicro.com/cgi-bin/gitweb/gitweb.cgi?p=linux-2.6-as… The machine driver now also does the I2C/SPI probing (instead of the codec) and also does any codec IO (to better support multiple controllers). Fwiw, I've not tested any of this code atm. I plan to start this tomorrow on pxa2xx and i.MX31 and would like to get some feedback before porting remaining platforms and codecs over. Liam

4 6

[alsa-devel] Documentation for params_xxx() macros?
by Timur Tabi 14 Jun '07

14 Jun '07

Is there documentation that describes each of the params_xxx() macros? If not, then which macro tells me how many periods there are? Is it params_periods()? -- Timur Tabi Linux Kernel Developer @ Freescale

1 0

[alsa-devel] aplay hangs with execve("/build/bin/aplay", ["aplay"], [/* 8 vars */
by Pharaoh . 14 Jun '07

14 Jun '07

Hi I am using alsa lib and alsa utils 1.0.14 on my omap based board. When I try to test my my alsa driver using aplay it just hangs at the very first step. The strace output shows nothing else except the following line, execve("/build/bin/aplay", ["aplay"], [/* 8 vars */ What I am missing?

1 0

[alsa-devel] Drivers for M-Audio Firewire 410
by Cédric 14 Jun '07

14 Jun '07

Hello, Im a french user of Linux (Ubuntu Studio 7.04) and cant install my new hardware (M-Audio Firewire 410). Ive send a mail to the M-Audios technical support, but they have no solution. They recommended me to contact yourself. Could you help me for this problem. Do you need more informations about my computer hardware ? Syncerly. Cédric

2 1

[alsa-devel] [PATCH]is_power_of_2-sound/pcm_params.h
by vignesh babu 14 Jun '07

14 Jun '07

Replacing (n & (n-1)) in the context of power of 2 checks with is_power_of_2 Signed-off-by: vignesh babu <vignesh.babu(a)wipro.com> --- diff --git a/include/sound/pcm_params.h b/include/sound/pcm_params.h index 85cf1cf..dee298e 100644 --- a/include/sound/pcm_params.h +++ b/include/sound/pcm_params.h @@ -21,6 +21,7 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA * */ +#include <linux/log2.h> int snd_pcm_hw_param_first(struct snd_pcm_substream *pcm, struct snd_pcm_hw_params *params, @@ -170,7 +171,7 @@ static inline int snd_mask_single(const struct snd_mask *mask) for (i = 0; i < SNDRV_MASK_SIZE; i++) { if (! mask->bits[i]) continue; - if (mask->bits[i] & (mask->bits[i] - 1)) + if (!is_power_of_2(mask->bits[i])) return 0; if (c) return 0; -- Vignesh Babu BM _____________________________________________________________ "Why is it that every time I'm with you, makes me believe in magic?" The information contained in this electronic message and any attachments to this message are intended for the exclusive use of the addressee(s) and may contain proprietary, confidential or privileged information. If you are not the intended recipient, you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately and destroy all copies of this message and any attachments. WARNING: Computer viruses can be transmitted via email. The recipient should check this email and any attachments for the presence of viruses. The company accepts no liability for any damage caused by any virus transmitted by this email. www.wipro.com

1 0

[alsa-devel] [PATCH] Fix build error with strict mm checking
by Martin Habets 13 Jun '07

13 Jun '07

Turning on STRICT_MM_TYPECHECKS in include/asm/page.h causes a build error for sparc32. This patch against 2.6.21 fixes this. Martin Signed-off-by: Martin Habets <errandir_news(a)mph.eclipse.co.uk> --- --- linux/sound/core/sgbuf.c.orig 2007-06-06 23:53:34.000000000 +0100 +++ linux/sound/core/sgbuf.c 2007-06-06 23:54:45.000000000 +0100 @@ -96,7 +96,7 @@ void *snd_malloc_sgbuf_pages(struct devi } sgbuf->size = size; - dmab->area = vmap(sgbuf->page_table, sgbuf->pages, VM_MAP, PAGE_KERNEL); + dmab->area = vmap(sgbuf->page_table, sgbuf->pages, VM_MAP, __pgprot(PAGE_KERNEL)); if (! dmab->area) goto _failed; return dmab->area;

2 1

[alsa-devel] Trouble understanding ALSA's DMA buffers
by Timur Tabi 12 Jun '07

12 Jun '07

I'm writing an ALSA SOC driver for an I2S-based device, and I'm having a really hard time understanding how ALSA uses the DMA buffers. And yes, I've read the documentation and studied some sample source code. I used to write audio drivers for a living, but that was many years ago, and it wasn't for Linux. Perhaps the concepts in my head are outdated, but I just don't see enough explanation as to how DMA buffers are supposed to work. Back then, audio drivers used "ping pong" DMA buffers. A single DMA buffer is allocated, and the audio hardware is programmed to read from that buffer in a loop. That is, it would automatically restart reading from the beginning of the buffer without any reprogramming. The hardware would also be programmed to issue an interrupt when it got to the end of the buffer, and when it got to the half-way point. To start playback, you first filled the whole buffer with audio data, and then told the hardware to start playing. After the hardware got to the half-way point, it would issue an interrupt. You would then tell the OS you need more data, and you'd get it. You then copy that data into the first half of the buffer *while* the hardware was playing the second half. Later, the hardware would interrupt you when it got to the end of the buffer. You'd then copy more data to the 2nd half while the hardware is playing the first half. And so - hardware plays one half while you copy data to the other half. Hence, "ping pong". So how do I implement this in ALSA? The "Writing an ALSA Driver" document doesn't even contain the words "ping" or "pong". -- Timur Tabi Linux Kernel Developer @ Freescale

4 6

[alsa-devel] [ASoC] bug in soc_pcm_open
by Matthieu CASTET 12 Jun '07

12 Jun '07

Hi, it seems there is a bug in soc_pcm_open. In some case [1] we are in a error path, but we don't set the ret return value. This cause bug/crash from alsa core. Thanks Matthieu [1]http://hg-mirror.alsa-project.org/alsa-kernel/file/38926de0e79c/soc/soc-c… if (!runtime->hw.rates) { 218 printk(KERN_ERR "asoc: %s <-> %s No matching rates\n", 219 codec_dai->name, cpu_dai->name); 220 goto machine_err; 221 } 222 if (!runtime->hw.formats) { 223 printk(KERN_ERR "asoc: %s <-> %s No matching formats\n", 224 codec_dai->name, cpu_dai->name); 225 goto machine_err; 226 } 227 if (!runtime->hw.channels_min || !runtime->hw.channels_max) { 228 printk(KERN_ERR "asoc: %s <-> %s No matching channels\n", 229 codec_dai->name, cpu_dai->name); 230 goto machine_err; 231 }

4 4

[alsa-devel] Realtek 268
by Steven Zakulec 12 Jun '07

12 Jun '07

I have tried the current (from about 6 hours ago) drivers+lib from the HG repository. My card is now labelled as an ALC 268, and shows me what appears to be a correct number of options in the mixer. Unfortunately, I still get no sound. I've compiled the driver with --debug=full, and the lib with the debug. The following is from dmesg when I removed the old snd-hda-intel module, did a make install, then did modprobe snd-hda-intel: (I cleared out dmesg before I did the modprobe) [ 1473.892000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 21 [ 1473.892000] PCI: Setting latency timer of device 0000:00:1b.0 to 64 [ 1474.092000] hda_codec: Unknown model for ALC268, trying auto-probe from BIOS... [ 1474.140000] ALSA /home/szakulec/alsa-hg/alsa-driver/pci/hda/hda_codec.c:2339: autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) [ 1474.140000] ALSA /home/szakulec/alsa-hg/alsa-driver/pci/hda/hda_codec.c:2343: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) [ 1474.140000] ALSA /home/szakulec/alsa-hg/alsa-driver/pci/hda/hda_codec.c:2347: hp_outs=1 (0x15/0x0/0x0/0x0/0x0) [ 1474.140000] ALSA /home/szakulec/alsa-hg/alsa-driver/pci/hda/hda_codec.c:2355: inputs: mic=0x19, fmic=0x18, line=0x0, fline=0x0, cd=0x0, aux=0x0 [ 1474.864000] ALSA /home/szakulec/alsa-hg/alsa-driver/pci/hda/../../alsa-kernel/pci/hda/patch_si3054.c:244: si3054: cannot initialize. EXT MID = 0000 [ 1474.872000] ALSA /home/szakulec/alsa-hg/alsa-driver/pci/hda/../../alsa-kernel/pci/hda/patch_si3054.c:256: Link Frame Detect(FDT) is not ready (line status: 0000) My /proc/asound/card0/codeco#0 is as follows: cat /proc/asound/card0/codec#0 Codec: Realtek ALC268 Address: 0 Vendor Id: 0x10ec0268 Subsystem Id: 0x1179ff10 Revision Id: 0x100003 Default PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Default Amp-In caps: N/A Default Amp-Out caps: N/A Node 0x02 [Audio Output] wcaps 0x1d: Stereo Amp-Out Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0 Amp-Out vals: [0x00 0x00] PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Node 0x03 [Audio Output] wcaps 0x1d: Stereo Amp-Out Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0 Amp-Out vals: [0x40 0x40] PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Node 0x04 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x05 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x06 [Audio Output] wcaps 0x211: Stereo Digital PCM: rates [0x5e0]: 44100 48000 88200 96000 192000 bits [0x1e]: 16 20 24 32 formats [0x1]: PCM Node 0x07 [Audio Input] wcaps 0x100111: Stereo PCM: rates [0x160]: 44100 48000 96000 bits [0x6]: 16 20 formats [0x1]: PCM Connection: 1 0x24 Node 0x08 [Audio Input] wcaps 0x100111: Stereo PCM: rates [0x160]: 44100 48000 96000 bits [0x6]: 16 20 formats [0x1]: PCM Connection: 1 0x23 Node 0x09 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x0a [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x0b [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x0c [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x0d [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x0e [Audio Mixer] wcaps 0x20010a: Mono Amp-In Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00] Connection: 1 0x02 Node 0x0f [Audio Mixer] wcaps 0x20010b: Stereo Amp-In Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x80 0x80] Connection: 2 0x02 0x1d Node 0x10 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x80 0x80] [0x80 0x80] Connection: 3 0x03 0x1d 0x02 Node 0x11 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x12 [Pin Complex] wcaps 0x400001: Stereo Pincap 0x0820: IN Pin Default 0x411111f0: [N/A] Speaker at Ext Rear Conn = 1/8, Color = Black Pin-ctls: 0x00: Node 0x13 [Pin Complex] wcaps 0x400001: Stereo Pincap 0x0820: IN Pin Default 0x411111f0: [N/A] Speaker at Ext Rear Conn = 1/8, Color = Black Pin-ctls: 0x00: Node 0x14 [Pin Complex] wcaps 0x40018d: Stereo Amp-Out Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x00 0x00] Pincap 0x081003c: IN OUT HP EAPD Detect Pin Default 0x99130110: [Fixed] Speaker at Int ATAPI Conn = ATAPI, Color = Unknown Pin-ctls: 0x40: OUT Connection: 1 0x0f Node 0x15 [Pin Complex] wcaps 0x40018d: Stereo Amp-Out Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x00 0x00] Pincap 0x081003c: IN OUT HP EAPD Detect Pin Default 0x02211020: [Jack] HP Out at Ext Front Conn = 1/8, Color = Black Pin-ctls: 0xc0: OUT HP Connection: 1 0x10 Node 0x16 [Pin Complex] wcaps 0x40010c: Mono Amp-Out Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80] Pincap 0x0810: OUT Pin Default 0x411111f0: [N/A] Speaker at Ext Rear Conn = 1/8, Color = Black Pin-ctls: 0x00: Connection: 1 0x0e Node 0x17 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x18 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x02, stepsize=0x4f, mute=0 Amp-In vals: [0x00 0x00] Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80] Pincap 0x083734: IN OUT Detect Pin Default 0x02a11830: [Jack] Mic at Ext Front Conn = 1/8, Color = Black Pin-ctls: 0x24: IN Connection: 1 0x02 Node 0x19 [Pin Complex] wcaps 0x40008b: Stereo Amp-In Amp-In caps: ofs=0x00, nsteps=0x02, stepsize=0x4f, mute=0 Amp-In vals: Pincap 0x083724: IN Detect Pin Default 0x99a30940: [Fixed] Mic at Int ATAPI Conn = ATAPI, Color = Unknown Pin-ctls: 0x24: IN Node 0x1a [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x02, stepsize=0x4f, mute=0 Amp-In vals: [0x00 0x00] Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80] Pincap 0x083734: IN OUT Detect Pin Default 0x411111f0: [N/A] Speaker at Ext Rear Conn = 1/8, Color = Black Pin-ctls: 0x20: IN Connection: 1 0x02 Node 0x1b [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x1c [Pin Complex] wcaps 0x400001: Stereo Pincap 0x0820: IN Pin Default 0x411111f0: [N/A] Speaker at Ext Rear Conn = 1/8, Color = Black Pin-ctls: 0x20: IN Node 0x1d [Pin Complex] wcaps 0x400000: Mono Pincap 0x0820: IN Pin Default 0x4015812d: [N/A] Speaker at Ext N/A Conn = Optical, Color = Purple Pin-ctls: 0x20: IN Node 0x1e [Pin Complex] wcaps 0x400380: Mono Digital Pincap 0x0810: OUT Pin Default 0x411111f0: [N/A] Speaker at Ext Rear Conn = 1/8, Color = Black Pin-ctls: 0x40: OUT Connection: 1 0x06 Node 0x1f [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono Node 0x21 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x22 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x23 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out Amp-Out caps: ofs=0x0b, nsteps=0x1f, stepsize=0x05, mute=1 Amp-Out vals: [0x81 0x81] Connection: 7 0x18 0x19 0x1a 0x1c 0x14 0x15* 0x12 Node 0x24 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out Amp-Out caps: ofs=0x0b, nsteps=0x1f, stepsize=0x05, mute=1 Amp-Out vals: [0x81 0x81] Connection: 7 0x18 0x19 0x1a 0x1c 0x14* 0x15 0x13 Output for the audio device (lspci -vvv) below: 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) Subsystem: Toshiba America Info Systems Unknown device ff10 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 21 Region 0: Memory at f0b40000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [70] Express Unknown type IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <64ns, L1 <1us Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0 Link: Latency L0s <64ns, L1 <1us Link: ASPM Disabled CommClk- ExtSynch- Link: Speed unknown, Width x0

2 1