May 2023 - Alsa-devel - mailman.alsa-project.org

[PATCH v4] ASoC: dt-bindings: nau8825: Convert to dtschema
by David Lin 12 May '23

12 May '23

Convert the NAU8825 audio CODEC bindings to DT schema. Signed-off-by: David Lin <CTLIN0(a)nuvoton.com> Changes: V3 -> V4: - remove the description from interrupts, clocks and clock-names properites - add sound-dai-cells property and update the dts example V2 -> V3: - refine node name from "nau8825" to "codec" for generic purpose V1 -> V2: - add interrupts properties - add maximum to nuvoton,jack-insert-debounce and nuvoton,jack-eject-debounce properites - add a enum item for nuvoton,short-key-debounce properites - add default value for most properites - add maxItems to clocks properites and mclk entries to clock-names properites - refine wrong indentation from clocks and clock-names - refine dts example for interrupts and clocks - remove headset label from dts example --- .../devicetree/bindings/sound/nau8825.txt | 111 -------- .../bindings/sound/nuvoton,nau8825.yaml | 239 ++++++++++++++++++ 2 files changed, 239 insertions(+), 111 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sound/nau8825.txt create mode 100644 Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml diff --git a/Documentation/devicetree/bindings/sound/nau8825.txt b/Documentation/devicetree/bindings/sound/nau8825.txt deleted file mode 100644 index a9c34526f4cb..000000000000 --- a/Documentation/devicetree/bindings/sound/nau8825.txt +++ /dev/null @@ -1,111 +0,0 @@ -Nuvoton NAU8825 audio codec - -This device supports I2C only. - -Required properties: - - compatible : Must be "nuvoton,nau8825" - - - reg : the I2C address of the device. This is either 0x1a (CSB=0) or 0x1b (CSB=1). - -Optional properties: - - nuvoton,jkdet-enable: Enable jack detection via JKDET pin. - - nuvoton,jkdet-pull-enable: Enable JKDET pin pull. If set - pin pull enabled, - otherwise pin in high impedance state. - - nuvoton,jkdet-pull-up: Pull-up JKDET pin. If set then JKDET pin is pull up, otherwise pull down. - - nuvoton,jkdet-polarity: JKDET pin polarity. 0 - active high, 1 - active low. - - - nuvoton,vref-impedance: VREF Impedance selection - 0 - Open - 1 - 25 kOhm - 2 - 125 kOhm - 3 - 2.5 kOhm - - - nuvoton,micbias-voltage: Micbias voltage level. - 0 - VDDA - 1 - VDDA - 2 - VDDA * 1.1 - 3 - VDDA * 1.2 - 4 - VDDA * 1.3 - 5 - VDDA * 1.4 - 6 - VDDA * 1.53 - 7 - VDDA * 1.53 - - - nuvoton,sar-threshold-num: Number of buttons supported - - nuvoton,sar-threshold: Impedance threshold for each button. Array that contains up to 8 buttons configuration. SAR value is calculated as - SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R) - where MICBIAS is configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by 'nuvoton,sar-voltage', R - button impedance. - Refer datasheet section 10.2 for more information about threshold calculation. - - - nuvoton,sar-hysteresis: Button impedance measurement hysteresis. - - - nuvoton,sar-voltage: Reference voltage for button impedance measurement. - 0 - VDDA - 1 - VDDA - 2 - VDDA * 1.1 - 3 - VDDA * 1.2 - 4 - VDDA * 1.3 - 5 - VDDA * 1.4 - 6 - VDDA * 1.53 - 7 - VDDA * 1.53 - - - nuvoton,sar-compare-time: SAR compare time - 0 - 500 ns - 1 - 1 us - 2 - 2 us - 3 - 4 us - - - nuvoton,sar-sampling-time: SAR sampling time - 0 - 2 us - 1 - 4 us - 2 - 8 us - 3 - 16 us - - - nuvoton,short-key-debounce: Button short key press debounce time. - 0 - 30 ms - 1 - 50 ms - 2 - 100 ms - 3 - 30 ms - - - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms - - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms - - - nuvoton,crosstalk-enable: make crosstalk function enable if set. - - - nuvoton,adcout-drive-strong: make the drive strength of ADCOUT IO PIN strong if set. - Otherwise, the drive keeps normal strength. - - - nuvoton,adc-delay-ms: Delay (in ms) to make input path stable and avoid pop noise. The - default value is 125 and range between 125 to 500 ms. - - - clocks: list of phandle and clock specifier pairs according to common clock bindings for the - clocks described in clock-names - - clock-names: should include "mclk" for the MCLK master clock - -Example: - - headset: nau8825@1a { - compatible = "nuvoton,nau8825"; - reg = <0x1a>; - interrupt-parent = <&gpio>; - interrupts = <TEGRA_GPIO(E, 6) IRQ_TYPE_LEVEL_LOW>; - nuvoton,jkdet-enable; - nuvoton,jkdet-pull-enable; - nuvoton,jkdet-pull-up; - nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>; - nuvoton,vref-impedance = <2>; - nuvoton,micbias-voltage = <6>; - // Setup 4 buttons impedance according to Android specification - nuvoton,sar-threshold-num = <4>; - nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>; - nuvoton,sar-hysteresis = <1>; - nuvoton,sar-voltage = <0>; - nuvoton,sar-compare-time = <0>; - nuvoton,sar-sampling-time = <0>; - nuvoton,short-key-debounce = <2>; - nuvoton,jack-insert-debounce = <7>; - nuvoton,jack-eject-debounce = <7>; - nuvoton,crosstalk-enable; - - clock-names = "mclk"; - clocks = <&tegra_pmc TEGRA_PMC_CLK_OUT_2>; - }; diff --git a/Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml b/Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml new file mode 100644 index 000000000000..a54f194a0b49 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml @@ -0,0 +1,239 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/nuvoton,nau8825.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NAU8825 audio CODEC + +maintainers: + - John Hsu <KCHSU0(a)nuvoton.com> + +allOf: + - $ref: dai-common.yaml# + +properties: + compatible: + enum: + - nuvoton,nau8825 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + nuvoton,jkdet-enable: + description: + Enable jack detection via JKDET pin. + type: boolean + + nuvoton,jkdet-pull-enable: + description: + Enable JKDET pin pull. + If set - pin pull enabled, otherwise pin in high impedance state. + type: boolean + + nuvoton,jkdet-pull-up: + description: + Pull-up JKDET pin. + If set then JKDET pin is pull up, otherwise pull down. + type: boolean + + nuvoton,jkdet-polarity: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + JKDET pin polarity. + enum: + - 0 # active high + - 1 # active low + default: 1 + + nuvoton,vref-impedance: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + VREF Impedance selection. + enum: + - 0 # Open + - 1 # 25 kOhm + - 2 # 125 kOhm + - 3 # 2.5 kOhm + default: 2 + + nuvoton,micbias-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Micbias voltage level. + enum: + - 0 # VDDA + - 1 # VDDA + - 2 # VDDA * 1.1 + - 3 # VDDA * 1.2 + - 4 # VDDA * 1.3 + - 5 # VDDA * 1.4 + - 6 # VDDA * 1.53 + - 7 # VDDA * 1.53 + default: 6 + + nuvoton,sar-threshold-num: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Number of buttons supported. + minimum: 1 + maximum: 4 + default: 4 + + nuvoton,sar-threshold: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + Impedance threshold for each button. Array that contains up to 8 buttons + configuration. SAR value is calculated as + SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R) where MICBIAS is + configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by + 'nuvoton,sar-voltage', R - button impedance. + Refer datasheet section 10.2 for more information about threshold + calculation. + minItems: 1 + maxItems: 4 + items: + minimum: 0 + maximum: 255 + + nuvoton,sar-hysteresis: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Button impedance measurement hysteresis. + default: 0 + + nuvoton,sar-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Reference voltage for button impedance measurement. + enum: + - 0 # VDDA + - 1 # VDDA + - 2 # VDDA * 1.1 + - 3 # VDDA * 1.2 + - 4 # VDDA * 1.3 + - 5 # VDDA * 1.4 + - 6 # VDDA * 1.53 + - 7 # VDDA * 1.53 + default: 6 + + nuvoton,sar-compare-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + SAR compare time. + enum: + - 0 # 500 ns + - 1 # 1 us + - 2 # 2 us + - 3 # 4 us + default: 1 + + nuvoton,sar-sampling-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + SAR sampling time. + enum: + - 0 # 2 us + - 1 # 4 us + - 2 # 8 us + - 3 # 16 us + default: 1 + + nuvoton,short-key-debounce: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Button short key press debounce time. + enum: + - 0 # 30 ms + - 1 # 50 ms + - 2 # 100 ms + - 3 # 30 ms + default: 3 + + nuvoton,jack-insert-debounce: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + number from 0 to 7 that sets debounce time to 2^(n+2) ms. + maximum: 7 + default: 7 + + nuvoton,jack-eject-debounce: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + number from 0 to 7 that sets debounce time to 2^(n+2) ms + maximum: 7 + default: 0 + + nuvoton,crosstalk-enable: + description: + make crosstalk function enable if set. + type: boolean + + nuvoton,adcout-drive-strong: + description: + make the drive strength of ADCOUT IO PIN strong if set. + Otherwise, the drive keeps normal strength. + type: boolean + + nuvoton,adc-delay-ms: + description: + Delay (in ms) to make input path stable and avoid pop noise. + The default value is 125 and range between 125 to 500 ms. + minimum: 125 + maximum: 500 + default: 125 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: mclk + + '#sound-dai-cells': + const: 0 + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + codec@1a { + #sound-dai-cells = <0>; + compatible = "nuvoton,nau8825"; + reg = <0x1a>; + interrupt-parent = <&gpio>; + interrupts = <38 IRQ_TYPE_LEVEL_LOW>; + nuvoton,jkdet-enable; + nuvoton,jkdet-pull-enable; + nuvoton,jkdet-pull-up; + nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>; + nuvoton,vref-impedance = <2>; + nuvoton,micbias-voltage = <6>; + // Setup 4 buttons impedance according to Android specification + nuvoton,sar-threshold-num = <4>; + nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>; + nuvoton,sar-hysteresis = <1>; + nuvoton,sar-voltage = <0>; + nuvoton,sar-compare-time = <0>; + nuvoton,sar-sampling-time = <0>; + nuvoton,short-key-debounce = <2>; + nuvoton,jack-insert-debounce = <7>; + nuvoton,jack-eject-debounce = <7>; + nuvoton,crosstalk-enable; + + clock-names = "mclk"; + clocks = <&tegra_pmc 1>; + }; + }; -- 2.25.1

3 2

[PATCH 0/6] Fix soc compress playback deadlock in 5.15
by yixuanjiang 12 May '23

12 May '23

The patch in 5.15 aa9ff6a4955f ("ASoC: soc-compress: Reposition and add pcm_mutex") will cause the deadlock when close compress playback. It needs backport patch b7898396f4 ("ASoC: soc-pcm: Fix and cleanup DPCM locking commit") to prevent the deadlock issue. Rootcause is patch b7898396f4 will remove pcm_mutex in soc_pcm_hw_clean then patch aa9ff6a4955f add pcm_mutex acqurie back in snd_compr_free to fix regression cause from b7898396f4. If only apply aa9ff6a4955f, it will acqurie pcm_mutex twice cause the deadlock. There are total 6 patches on these related backport [ 212.063445] sysrq: Show Blocked State [ 212.064964] Call trace: [ 212.064974] __switch_to+0x244/0x454 [ 212.065075] __schedule+0x5fc/0xbdc [ 212.065092] schedule+0x154/0x258 [ 212.065103] schedule_preempt_disabled+0x30/0x50 [ 212.065115] __mutex_lock+0x36c/0x794 [ 212.065135] __mutex_lock_slowpath+0x1c/0x2c [ 212.065145] soc_pcm_hw_clean+0x6c/0x364 [ 212.065177] dpcm_be_dai_hw_free+0x20c/0x304 [ 212.065188] soc_compr_free_fe+0x130/0x448 [ 212.065230] snd_compr_free+0xac/0x148 [ 212.065316] __fput+0x104/0x438 [ 212.065347] ____fput+0x18/0x28 [ 212.065409] task_work_run+0x144/0x1f8 [ 212.065474] do_notify_resume+0x1d24/0x27b0 [ 212.065518] el0_svc+0x68/0xc4 [ 212.065601] el0t_64_sync_handler+0x8c/0xfc [ 212.065610] el0t_64_sync+0x1b0/0x1b4 *** BLURB HERE *** Pierre-Louis Bossart (4): ASoC: soc-pcm: use GFP_ATOMIC for dpcm structure ASoC: soc-pcm: align BE 'atomicity' with that of the FE ASoC: soc-pcm: test refcount before triggering ASoC: soc-pcm: fix BE handling of PAUSE_RELEASE Takashi Iwai (2): ASoC: soc-pcm: Fix and cleanup DPCM locking ASoC: soc-pcm: serialize BE triggers include/sound/soc-dpcm.h | 2 + include/sound/soc.h | 2 - sound/soc/soc-core.c | 1 - sound/soc/soc-pcm.c | 351 +++++++++++++++++++++++++++------------ 4 files changed, 246 insertions(+), 110 deletions(-) -- 2.40.1.521.gf1e218fcd8-goog

2 7

Looking for alsaunmute script
by GitHub issues - opened 11 May '23

11 May '23

alsa-project/alsa-utils issue #211 was opened from DenverEllis: I have a friend that is having trouble with their legion 7 laptop. Perusing a very long kernel thread I saw mention of an alsaunmute script and I am having a hard time tracking it down. I believ perex authored it and I saw it mentioned that it was a part of alsa-utils, but alas I have had no luck in finding this script. Issue URL : https://github.com/alsa-project/alsa-utils/issues/211 Repository URL: https://github.com/alsa-project/alsa-utils

1 0

[PATCH AUTOSEL 5.10 2/3] ALSA: hda: Glenfly: add HD Audio PCI IDs and HDMI Codec Vendor IDs.
by Sasha Levin 11 May '23

11 May '23

From: jasontao <jasontao(a)glenfly.com> [ Upstream commit c51e431052e2eacfb23fbf6b39bc6c8770d9827a ] Add a set of HD Audio PCI IDS, and the HDMI codec vendor IDs for Glenfly Gpus. - In default_bdl_pos_adj, set bdl to 128 as Glenfly Gpus have hardware limitation, need to increase hdac interrupt interval. - In azx_first_init, enable polling mode for Glenfly Gpu. When the codec complete the command, it sends interrupt and writes response entries to memory, howerver, the write requests sometimes are not actually synchronized to memory when driver handle hdac interrupt on Glenfly Gpus. If the RIRB status is not updated in the interrupt handler, azx_rirb_get_response keeps trying to recevie a response from rirb until 1s timeout. Enabling polling mode for Glenfly Gpu can fix the issue. - In patch_gf_hdmi, set Glenlfy Gpu Codec's no_sticky_stream as it need driver to do actual clean-ups for the linked codec when switch from one codec to another. Signed-off-by: jasontao <jasontao(a)glenfly.com> Signed-off-by: Reaper Li <reaperlioc(a)glenfly.com> Link: https://lore.kernel.org/r/20230426013059.4329-1-reaperlioc@glenfly.com Signed-off-by: Takashi Iwai <tiwai(a)suse.de> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- sound/pci/hda/hda_intel.c | 21 +++++++++++++++++++++ sound/pci/hda/patch_hdmi.c | 22 ++++++++++++++++++++++ 2 files changed, 43 insertions(+) diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c index de1fe604905f3..1f641712233ef 100644 --- a/sound/pci/hda/hda_intel.c +++ b/sound/pci/hda/hda_intel.c @@ -264,6 +264,7 @@ enum { AZX_DRIVER_ATI, AZX_DRIVER_ATIHDMI, AZX_DRIVER_ATIHDMI_NS, + AZX_DRIVER_GFHDMI, AZX_DRIVER_VIA, AZX_DRIVER_SIS, AZX_DRIVER_ULI, @@ -386,6 +387,7 @@ static const char * const driver_short_names[] = { [AZX_DRIVER_ATI] = "HDA ATI SB", [AZX_DRIVER_ATIHDMI] = "HDA ATI HDMI", [AZX_DRIVER_ATIHDMI_NS] = "HDA ATI HDMI", + [AZX_DRIVER_GFHDMI] = "HDA GF HDMI", [AZX_DRIVER_VIA] = "HDA VIA VT82xx", [AZX_DRIVER_SIS] = "HDA SIS966", [AZX_DRIVER_ULI] = "HDA ULI M5461", @@ -1783,6 +1785,12 @@ static int default_bdl_pos_adj(struct azx *chip) } switch (chip->driver_type) { + /* + * increase the bdl size for Glenfly Gpus for hardware + * limitation on hdac interrupt interval + */ + case AZX_DRIVER_GFHDMI: + return 128; case AZX_DRIVER_ICH: case AZX_DRIVER_PCH: return 1; @@ -1902,6 +1910,12 @@ static int azx_first_init(struct azx *chip) pci_write_config_dword(pci, PCI_BASE_ADDRESS_1, 0); } #endif + /* + * Fix response write request not synced to memory when handle + * hdac interrupt on Glenfly Gpus + */ + if (chip->driver_type == AZX_DRIVER_GFHDMI) + bus->polling_mode = 1; err = pci_request_regions(pci, "ICH HD audio"); if (err < 0) @@ -2011,6 +2025,7 @@ static int azx_first_init(struct azx *chip) chip->playback_streams = ATIHDMI_NUM_PLAYBACK; chip->capture_streams = ATIHDMI_NUM_CAPTURE; break; + case AZX_DRIVER_GFHDMI: case AZX_DRIVER_GENERIC: default: chip->playback_streams = ICH6_NUM_PLAYBACK; @@ -2756,6 +2771,12 @@ static const struct pci_device_id azx_ids[] = { { PCI_DEVICE(0x1002, 0xab38), .driver_data = AZX_DRIVER_ATIHDMI_NS | AZX_DCAPS_PRESET_ATI_HDMI_NS | AZX_DCAPS_PM_RUNTIME }, + /* GLENFLY */ + { PCI_DEVICE(0x6766, PCI_ANY_ID), + .class = PCI_CLASS_MULTIMEDIA_HD_AUDIO << 8, + .class_mask = 0xffffff, + .driver_data = AZX_DRIVER_GFHDMI | AZX_DCAPS_POSFIX_LPIB | + AZX_DCAPS_NO_MSI | AZX_DCAPS_NO_64BIT }, /* VIA VT8251/VT8237A */ { PCI_DEVICE(0x1106, 0x3288), .driver_data = AZX_DRIVER_VIA }, /* VIA GFX VT7122/VX900 */ diff --git a/sound/pci/hda/patch_hdmi.c b/sound/pci/hda/patch_hdmi.c index 1afe9cddb69eb..bd151465f2089 100644 --- a/sound/pci/hda/patch_hdmi.c +++ b/sound/pci/hda/patch_hdmi.c @@ -4287,6 +4287,22 @@ static int patch_via_hdmi(struct hda_codec *codec) return patch_simple_hdmi(codec, VIAHDMI_CVT_NID, VIAHDMI_PIN_NID); } +static int patch_gf_hdmi(struct hda_codec *codec) +{ + int err; + + err = patch_generic_hdmi(codec); + if (err) + return err; + + /* + * Glenfly GPUs have two codecs, stream switches from one codec to + * another, need to do actual clean-ups in codec_cleanup_stream + */ + codec->no_sticky_stream = 1; + return 0; +} + /* * patch entries */ @@ -4376,6 +4392,12 @@ HDA_CODEC_ENTRY(0x10de009f, "GPU 9f HDMI/DP", patch_nvhdmi), HDA_CODEC_ENTRY(0x10de00a0, "GPU a0 HDMI/DP", patch_nvhdmi), HDA_CODEC_ENTRY(0x10de8001, "MCP73 HDMI", patch_nvhdmi_2ch), HDA_CODEC_ENTRY(0x10de8067, "MCP67/68 HDMI", patch_nvhdmi_2ch), +HDA_CODEC_ENTRY(0x67663d82, "Arise 82 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d83, "Arise 83 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d84, "Arise 84 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d85, "Arise 85 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d86, "Arise 86 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d87, "Arise 87 HDMI/DP", patch_gf_hdmi), HDA_CODEC_ENTRY(0x11069f80, "VX900 HDMI/DP", patch_via_hdmi), HDA_CODEC_ENTRY(0x11069f81, "VX900 HDMI/DP", patch_via_hdmi), HDA_CODEC_ENTRY(0x11069f84, "VX11 HDMI/DP", patch_generic_hdmi), -- 2.39.2

1 0

[PATCH AUTOSEL 5.15 3/5] ALSA: hda: Glenfly: add HD Audio PCI IDs and HDMI Codec Vendor IDs.
by Sasha Levin 11 May '23

11 May '23

From: jasontao <jasontao(a)glenfly.com> [ Upstream commit c51e431052e2eacfb23fbf6b39bc6c8770d9827a ] Add a set of HD Audio PCI IDS, and the HDMI codec vendor IDs for Glenfly Gpus. - In default_bdl_pos_adj, set bdl to 128 as Glenfly Gpus have hardware limitation, need to increase hdac interrupt interval. - In azx_first_init, enable polling mode for Glenfly Gpu. When the codec complete the command, it sends interrupt and writes response entries to memory, howerver, the write requests sometimes are not actually synchronized to memory when driver handle hdac interrupt on Glenfly Gpus. If the RIRB status is not updated in the interrupt handler, azx_rirb_get_response keeps trying to recevie a response from rirb until 1s timeout. Enabling polling mode for Glenfly Gpu can fix the issue. - In patch_gf_hdmi, set Glenlfy Gpu Codec's no_sticky_stream as it need driver to do actual clean-ups for the linked codec when switch from one codec to another. Signed-off-by: jasontao <jasontao(a)glenfly.com> Signed-off-by: Reaper Li <reaperlioc(a)glenfly.com> Link: https://lore.kernel.org/r/20230426013059.4329-1-reaperlioc@glenfly.com Signed-off-by: Takashi Iwai <tiwai(a)suse.de> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- sound/pci/hda/hda_intel.c | 21 +++++++++++++++++++++ sound/pci/hda/patch_hdmi.c | 22 ++++++++++++++++++++++ 2 files changed, 43 insertions(+) diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c index 5fce1ca8a393a..1379ac07df350 100644 --- a/sound/pci/hda/hda_intel.c +++ b/sound/pci/hda/hda_intel.c @@ -230,6 +230,7 @@ enum { AZX_DRIVER_ATI, AZX_DRIVER_ATIHDMI, AZX_DRIVER_ATIHDMI_NS, + AZX_DRIVER_GFHDMI, AZX_DRIVER_VIA, AZX_DRIVER_SIS, AZX_DRIVER_ULI, @@ -352,6 +353,7 @@ static const char * const driver_short_names[] = { [AZX_DRIVER_ATI] = "HDA ATI SB", [AZX_DRIVER_ATIHDMI] = "HDA ATI HDMI", [AZX_DRIVER_ATIHDMI_NS] = "HDA ATI HDMI", + [AZX_DRIVER_GFHDMI] = "HDA GF HDMI", [AZX_DRIVER_VIA] = "HDA VIA VT82xx", [AZX_DRIVER_SIS] = "HDA SIS966", [AZX_DRIVER_ULI] = "HDA ULI M5461", @@ -1742,6 +1744,12 @@ static int default_bdl_pos_adj(struct azx *chip) } switch (chip->driver_type) { + /* + * increase the bdl size for Glenfly Gpus for hardware + * limitation on hdac interrupt interval + */ + case AZX_DRIVER_GFHDMI: + return 128; case AZX_DRIVER_ICH: case AZX_DRIVER_PCH: return 1; @@ -1857,6 +1865,12 @@ static int azx_first_init(struct azx *chip) pci_write_config_dword(pci, PCI_BASE_ADDRESS_1, 0); } #endif + /* + * Fix response write request not synced to memory when handle + * hdac interrupt on Glenfly Gpus + */ + if (chip->driver_type == AZX_DRIVER_GFHDMI) + bus->polling_mode = 1; err = pcim_iomap_regions(pci, 1 << 0, "ICH HD audio"); if (err < 0) @@ -1957,6 +1971,7 @@ static int azx_first_init(struct azx *chip) chip->playback_streams = ATIHDMI_NUM_PLAYBACK; chip->capture_streams = ATIHDMI_NUM_CAPTURE; break; + case AZX_DRIVER_GFHDMI: case AZX_DRIVER_GENERIC: default: chip->playback_streams = ICH6_NUM_PLAYBACK; @@ -2694,6 +2709,12 @@ static const struct pci_device_id azx_ids[] = { { PCI_DEVICE(0x1002, 0xab38), .driver_data = AZX_DRIVER_ATIHDMI_NS | AZX_DCAPS_PRESET_ATI_HDMI_NS | AZX_DCAPS_PM_RUNTIME }, + /* GLENFLY */ + { PCI_DEVICE(0x6766, PCI_ANY_ID), + .class = PCI_CLASS_MULTIMEDIA_HD_AUDIO << 8, + .class_mask = 0xffffff, + .driver_data = AZX_DRIVER_GFHDMI | AZX_DCAPS_POSFIX_LPIB | + AZX_DCAPS_NO_MSI | AZX_DCAPS_NO_64BIT }, /* VIA VT8251/VT8237A */ { PCI_DEVICE(0x1106, 0x3288), .driver_data = AZX_DRIVER_VIA }, /* VIA GFX VT7122/VX900 */ diff --git a/sound/pci/hda/patch_hdmi.c b/sound/pci/hda/patch_hdmi.c index 8ed66c416c0e7..c8982c788835a 100644 --- a/sound/pci/hda/patch_hdmi.c +++ b/sound/pci/hda/patch_hdmi.c @@ -4298,6 +4298,22 @@ static int patch_via_hdmi(struct hda_codec *codec) return patch_simple_hdmi(codec, VIAHDMI_CVT_NID, VIAHDMI_PIN_NID); } +static int patch_gf_hdmi(struct hda_codec *codec) +{ + int err; + + err = patch_generic_hdmi(codec); + if (err) + return err; + + /* + * Glenfly GPUs have two codecs, stream switches from one codec to + * another, need to do actual clean-ups in codec_cleanup_stream + */ + codec->no_sticky_stream = 1; + return 0; +} + /* * patch entries */ @@ -4387,6 +4403,12 @@ HDA_CODEC_ENTRY(0x10de009f, "GPU 9f HDMI/DP", patch_nvhdmi), HDA_CODEC_ENTRY(0x10de00a0, "GPU a0 HDMI/DP", patch_nvhdmi), HDA_CODEC_ENTRY(0x10de8001, "MCP73 HDMI", patch_nvhdmi_2ch), HDA_CODEC_ENTRY(0x10de8067, "MCP67/68 HDMI", patch_nvhdmi_2ch), +HDA_CODEC_ENTRY(0x67663d82, "Arise 82 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d83, "Arise 83 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d84, "Arise 84 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d85, "Arise 85 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d86, "Arise 86 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d87, "Arise 87 HDMI/DP", patch_gf_hdmi), HDA_CODEC_ENTRY(0x11069f80, "VX900 HDMI/DP", patch_via_hdmi), HDA_CODEC_ENTRY(0x11069f81, "VX900 HDMI/DP", patch_via_hdmi), HDA_CODEC_ENTRY(0x11069f84, "VX11 HDMI/DP", patch_generic_hdmi), -- 2.39.2

1 0

[PATCH AUTOSEL 6.1 8/9] ASoC: Intel: soc-acpi-cht: Add quirk for Nextbook Ares 8A tablet
by Sasha Levin 11 May '23

11 May '23

From: Hans de Goede <hdegoede(a)redhat.com> [ Upstream commit ec6f82b4c63cc68f8dc03316e725106d242706be ] The Nextbook Ares 8A tablet which has Android as factory OS, has a buggy DSDT with both ESSX8316 and 10EC5651 ACPI devices. This tablet actually uses an rt5651 codec, but the matching code ends up picking the ESSX8316 device, add a quirk to ignote the ESSX8316 device on this tablet. Signed-off-by: Hans de Goede <hdegoede(a)redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart(a)linux.intel.com> Message-Id: <20230429104721.7176-1-hdegoede(a)redhat.com> Signed-off-by: Mark Brown <broonie(a)kernel.org> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- .../intel/common/soc-acpi-intel-cht-match.c | 26 +++++++++++++++++++ 1 file changed, 26 insertions(+) diff --git a/sound/soc/intel/common/soc-acpi-intel-cht-match.c b/sound/soc/intel/common/soc-acpi-intel-cht-match.c index 6beb00858c33f..cdcbf04b8832f 100644 --- a/sound/soc/intel/common/soc-acpi-intel-cht-match.c +++ b/sound/soc/intel/common/soc-acpi-intel-cht-match.c @@ -50,6 +50,31 @@ static struct snd_soc_acpi_mach *cht_quirk(void *arg) return mach; } +/* + * Some tablets with Android factory OS have buggy DSDTs with an ESSX8316 device + * in the ACPI tables. While they are not using an ESS8316 codec. These DSDTs + * also have an ACPI device for the correct codec, ignore the ESSX8316. + */ +static const struct dmi_system_id cht_ess8316_not_present_table[] = { + { + /* Nextbook Ares 8A */ + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Insyde"), + DMI_MATCH(DMI_PRODUCT_NAME, "CherryTrail"), + DMI_MATCH(DMI_BIOS_VERSION, "M882"), + }, + }, + { } +}; + +static struct snd_soc_acpi_mach *cht_ess8316_quirk(void *arg) +{ + if (dmi_check_system(cht_ess8316_not_present_table)) + return NULL; + + return arg; +} + static const struct snd_soc_acpi_codecs rt5640_comp_ids = { .num_codecs = 2, .codecs = { "10EC5640", "10EC3276" }, @@ -113,6 +138,7 @@ struct snd_soc_acpi_mach snd_soc_acpi_intel_cherrytrail_machines[] = { .drv_name = "bytcht_es8316", .fw_filename = "intel/fw_sst_22a8.bin", .board = "bytcht_es8316", + .machine_quirk = cht_ess8316_quirk, .sof_tplg_filename = "sof-cht-es8316.tplg", }, /* some CHT-T platforms rely on RT5640, use Baytrail machine driver */ -- 2.39.2

1 0

[PATCH AUTOSEL 6.1 3/9] ALSA: hda: Glenfly: add HD Audio PCI IDs and HDMI Codec Vendor IDs.
by Sasha Levin 11 May '23

11 May '23

From: jasontao <jasontao(a)glenfly.com> [ Upstream commit c51e431052e2eacfb23fbf6b39bc6c8770d9827a ] Add a set of HD Audio PCI IDS, and the HDMI codec vendor IDs for Glenfly Gpus. - In default_bdl_pos_adj, set bdl to 128 as Glenfly Gpus have hardware limitation, need to increase hdac interrupt interval. - In azx_first_init, enable polling mode for Glenfly Gpu. When the codec complete the command, it sends interrupt and writes response entries to memory, howerver, the write requests sometimes are not actually synchronized to memory when driver handle hdac interrupt on Glenfly Gpus. If the RIRB status is not updated in the interrupt handler, azx_rirb_get_response keeps trying to recevie a response from rirb until 1s timeout. Enabling polling mode for Glenfly Gpu can fix the issue. - In patch_gf_hdmi, set Glenlfy Gpu Codec's no_sticky_stream as it need driver to do actual clean-ups for the linked codec when switch from one codec to another. Signed-off-by: jasontao <jasontao(a)glenfly.com> Signed-off-by: Reaper Li <reaperlioc(a)glenfly.com> Link: https://lore.kernel.org/r/20230426013059.4329-1-reaperlioc@glenfly.com Signed-off-by: Takashi Iwai <tiwai(a)suse.de> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- sound/pci/hda/hda_intel.c | 21 +++++++++++++++++++++ sound/pci/hda/patch_hdmi.c | 22 ++++++++++++++++++++++ 2 files changed, 43 insertions(+) diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c index 77a592f219472..31e16feaa2b4f 100644 --- a/sound/pci/hda/hda_intel.c +++ b/sound/pci/hda/hda_intel.c @@ -227,6 +227,7 @@ enum { AZX_DRIVER_ATI, AZX_DRIVER_ATIHDMI, AZX_DRIVER_ATIHDMI_NS, + AZX_DRIVER_GFHDMI, AZX_DRIVER_VIA, AZX_DRIVER_SIS, AZX_DRIVER_ULI, @@ -349,6 +350,7 @@ static const char * const driver_short_names[] = { [AZX_DRIVER_ATI] = "HDA ATI SB", [AZX_DRIVER_ATIHDMI] = "HDA ATI HDMI", [AZX_DRIVER_ATIHDMI_NS] = "HDA ATI HDMI", + [AZX_DRIVER_GFHDMI] = "HDA GF HDMI", [AZX_DRIVER_VIA] = "HDA VIA VT82xx", [AZX_DRIVER_SIS] = "HDA SIS966", [AZX_DRIVER_ULI] = "HDA ULI M5461", @@ -1743,6 +1745,12 @@ static int default_bdl_pos_adj(struct azx *chip) } switch (chip->driver_type) { + /* + * increase the bdl size for Glenfly Gpus for hardware + * limitation on hdac interrupt interval + */ + case AZX_DRIVER_GFHDMI: + return 128; case AZX_DRIVER_ICH: case AZX_DRIVER_PCH: return 1; @@ -1858,6 +1866,12 @@ static int azx_first_init(struct azx *chip) pci_write_config_dword(pci, PCI_BASE_ADDRESS_1, 0); } #endif + /* + * Fix response write request not synced to memory when handle + * hdac interrupt on Glenfly Gpus + */ + if (chip->driver_type == AZX_DRIVER_GFHDMI) + bus->polling_mode = 1; err = pcim_iomap_regions(pci, 1 << 0, "ICH HD audio"); if (err < 0) @@ -1959,6 +1973,7 @@ static int azx_first_init(struct azx *chip) chip->playback_streams = ATIHDMI_NUM_PLAYBACK; chip->capture_streams = ATIHDMI_NUM_CAPTURE; break; + case AZX_DRIVER_GFHDMI: case AZX_DRIVER_GENERIC: default: chip->playback_streams = ICH6_NUM_PLAYBACK; @@ -2724,6 +2739,12 @@ static const struct pci_device_id azx_ids[] = { { PCI_DEVICE(0x1002, 0xab38), .driver_data = AZX_DRIVER_ATIHDMI_NS | AZX_DCAPS_PRESET_ATI_HDMI_NS | AZX_DCAPS_PM_RUNTIME }, + /* GLENFLY */ + { PCI_DEVICE(0x6766, PCI_ANY_ID), + .class = PCI_CLASS_MULTIMEDIA_HD_AUDIO << 8, + .class_mask = 0xffffff, + .driver_data = AZX_DRIVER_GFHDMI | AZX_DCAPS_POSFIX_LPIB | + AZX_DCAPS_NO_MSI | AZX_DCAPS_NO_64BIT }, /* VIA VT8251/VT8237A */ { PCI_DEVICE(0x1106, 0x3288), .driver_data = AZX_DRIVER_VIA }, /* VIA GFX VT7122/VX900 */ diff --git a/sound/pci/hda/patch_hdmi.c b/sound/pci/hda/patch_hdmi.c index 5c6980394dcec..b784ef95390db 100644 --- a/sound/pci/hda/patch_hdmi.c +++ b/sound/pci/hda/patch_hdmi.c @@ -4489,6 +4489,22 @@ static int patch_via_hdmi(struct hda_codec *codec) return patch_simple_hdmi(codec, VIAHDMI_CVT_NID, VIAHDMI_PIN_NID); } +static int patch_gf_hdmi(struct hda_codec *codec) +{ + int err; + + err = patch_generic_hdmi(codec); + if (err) + return err; + + /* + * Glenfly GPUs have two codecs, stream switches from one codec to + * another, need to do actual clean-ups in codec_cleanup_stream + */ + codec->no_sticky_stream = 1; + return 0; +} + /* * patch entries */ @@ -4579,6 +4595,12 @@ HDA_CODEC_ENTRY(0x10de009f, "GPU 9f HDMI/DP", patch_nvhdmi), HDA_CODEC_ENTRY(0x10de00a0, "GPU a0 HDMI/DP", patch_nvhdmi), HDA_CODEC_ENTRY(0x10de8001, "MCP73 HDMI", patch_nvhdmi_2ch), HDA_CODEC_ENTRY(0x10de8067, "MCP67/68 HDMI", patch_nvhdmi_2ch), +HDA_CODEC_ENTRY(0x67663d82, "Arise 82 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d83, "Arise 83 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d84, "Arise 84 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d85, "Arise 85 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d86, "Arise 86 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d87, "Arise 87 HDMI/DP", patch_gf_hdmi), HDA_CODEC_ENTRY(0x11069f80, "VX900 HDMI/DP", patch_via_hdmi), HDA_CODEC_ENTRY(0x11069f81, "VX900 HDMI/DP", patch_via_hdmi), HDA_CODEC_ENTRY(0x11069f84, "VX11 HDMI/DP", patch_generic_hdmi), -- 2.39.2

1 0

[PATCH AUTOSEL 6.2 09/10] ASoC: Intel: soc-acpi-cht: Add quirk for Nextbook Ares 8A tablet
by Sasha Levin 11 May '23

11 May '23

From: Hans de Goede <hdegoede(a)redhat.com> [ Upstream commit ec6f82b4c63cc68f8dc03316e725106d242706be ] The Nextbook Ares 8A tablet which has Android as factory OS, has a buggy DSDT with both ESSX8316 and 10EC5651 ACPI devices. This tablet actually uses an rt5651 codec, but the matching code ends up picking the ESSX8316 device, add a quirk to ignote the ESSX8316 device on this tablet. Signed-off-by: Hans de Goede <hdegoede(a)redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart(a)linux.intel.com> Message-Id: <20230429104721.7176-1-hdegoede(a)redhat.com> Signed-off-by: Mark Brown <broonie(a)kernel.org> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- .../intel/common/soc-acpi-intel-cht-match.c | 26 +++++++++++++++++++ 1 file changed, 26 insertions(+) diff --git a/sound/soc/intel/common/soc-acpi-intel-cht-match.c b/sound/soc/intel/common/soc-acpi-intel-cht-match.c index 6beb00858c33f..cdcbf04b8832f 100644 --- a/sound/soc/intel/common/soc-acpi-intel-cht-match.c +++ b/sound/soc/intel/common/soc-acpi-intel-cht-match.c @@ -50,6 +50,31 @@ static struct snd_soc_acpi_mach *cht_quirk(void *arg) return mach; } +/* + * Some tablets with Android factory OS have buggy DSDTs with an ESSX8316 device + * in the ACPI tables. While they are not using an ESS8316 codec. These DSDTs + * also have an ACPI device for the correct codec, ignore the ESSX8316. + */ +static const struct dmi_system_id cht_ess8316_not_present_table[] = { + { + /* Nextbook Ares 8A */ + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Insyde"), + DMI_MATCH(DMI_PRODUCT_NAME, "CherryTrail"), + DMI_MATCH(DMI_BIOS_VERSION, "M882"), + }, + }, + { } +}; + +static struct snd_soc_acpi_mach *cht_ess8316_quirk(void *arg) +{ + if (dmi_check_system(cht_ess8316_not_present_table)) + return NULL; + + return arg; +} + static const struct snd_soc_acpi_codecs rt5640_comp_ids = { .num_codecs = 2, .codecs = { "10EC5640", "10EC3276" }, @@ -113,6 +138,7 @@ struct snd_soc_acpi_mach snd_soc_acpi_intel_cherrytrail_machines[] = { .drv_name = "bytcht_es8316", .fw_filename = "intel/fw_sst_22a8.bin", .board = "bytcht_es8316", + .machine_quirk = cht_ess8316_quirk, .sof_tplg_filename = "sof-cht-es8316.tplg", }, /* some CHT-T platforms rely on RT5640, use Baytrail machine driver */ -- 2.39.2

1 0

[PATCH AUTOSEL 6.2 03/10] ALSA: hda: Glenfly: add HD Audio PCI IDs and HDMI Codec Vendor IDs.
by Sasha Levin 11 May '23

11 May '23

From: jasontao <jasontao(a)glenfly.com> [ Upstream commit c51e431052e2eacfb23fbf6b39bc6c8770d9827a ] Add a set of HD Audio PCI IDS, and the HDMI codec vendor IDs for Glenfly Gpus. - In default_bdl_pos_adj, set bdl to 128 as Glenfly Gpus have hardware limitation, need to increase hdac interrupt interval. - In azx_first_init, enable polling mode for Glenfly Gpu. When the codec complete the command, it sends interrupt and writes response entries to memory, howerver, the write requests sometimes are not actually synchronized to memory when driver handle hdac interrupt on Glenfly Gpus. If the RIRB status is not updated in the interrupt handler, azx_rirb_get_response keeps trying to recevie a response from rirb until 1s timeout. Enabling polling mode for Glenfly Gpu can fix the issue. - In patch_gf_hdmi, set Glenlfy Gpu Codec's no_sticky_stream as it need driver to do actual clean-ups for the linked codec when switch from one codec to another. Signed-off-by: jasontao <jasontao(a)glenfly.com> Signed-off-by: Reaper Li <reaperlioc(a)glenfly.com> Link: https://lore.kernel.org/r/20230426013059.4329-1-reaperlioc@glenfly.com Signed-off-by: Takashi Iwai <tiwai(a)suse.de> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- sound/pci/hda/hda_intel.c | 21 +++++++++++++++++++++ sound/pci/hda/patch_hdmi.c | 22 ++++++++++++++++++++++ 2 files changed, 43 insertions(+) diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c index 77a592f219472..31e16feaa2b4f 100644 --- a/sound/pci/hda/hda_intel.c +++ b/sound/pci/hda/hda_intel.c @@ -227,6 +227,7 @@ enum { AZX_DRIVER_ATI, AZX_DRIVER_ATIHDMI, AZX_DRIVER_ATIHDMI_NS, + AZX_DRIVER_GFHDMI, AZX_DRIVER_VIA, AZX_DRIVER_SIS, AZX_DRIVER_ULI, @@ -349,6 +350,7 @@ static const char * const driver_short_names[] = { [AZX_DRIVER_ATI] = "HDA ATI SB", [AZX_DRIVER_ATIHDMI] = "HDA ATI HDMI", [AZX_DRIVER_ATIHDMI_NS] = "HDA ATI HDMI", + [AZX_DRIVER_GFHDMI] = "HDA GF HDMI", [AZX_DRIVER_VIA] = "HDA VIA VT82xx", [AZX_DRIVER_SIS] = "HDA SIS966", [AZX_DRIVER_ULI] = "HDA ULI M5461", @@ -1743,6 +1745,12 @@ static int default_bdl_pos_adj(struct azx *chip) } switch (chip->driver_type) { + /* + * increase the bdl size for Glenfly Gpus for hardware + * limitation on hdac interrupt interval + */ + case AZX_DRIVER_GFHDMI: + return 128; case AZX_DRIVER_ICH: case AZX_DRIVER_PCH: return 1; @@ -1858,6 +1866,12 @@ static int azx_first_init(struct azx *chip) pci_write_config_dword(pci, PCI_BASE_ADDRESS_1, 0); } #endif + /* + * Fix response write request not synced to memory when handle + * hdac interrupt on Glenfly Gpus + */ + if (chip->driver_type == AZX_DRIVER_GFHDMI) + bus->polling_mode = 1; err = pcim_iomap_regions(pci, 1 << 0, "ICH HD audio"); if (err < 0) @@ -1959,6 +1973,7 @@ static int azx_first_init(struct azx *chip) chip->playback_streams = ATIHDMI_NUM_PLAYBACK; chip->capture_streams = ATIHDMI_NUM_CAPTURE; break; + case AZX_DRIVER_GFHDMI: case AZX_DRIVER_GENERIC: default: chip->playback_streams = ICH6_NUM_PLAYBACK; @@ -2724,6 +2739,12 @@ static const struct pci_device_id azx_ids[] = { { PCI_DEVICE(0x1002, 0xab38), .driver_data = AZX_DRIVER_ATIHDMI_NS | AZX_DCAPS_PRESET_ATI_HDMI_NS | AZX_DCAPS_PM_RUNTIME }, + /* GLENFLY */ + { PCI_DEVICE(0x6766, PCI_ANY_ID), + .class = PCI_CLASS_MULTIMEDIA_HD_AUDIO << 8, + .class_mask = 0xffffff, + .driver_data = AZX_DRIVER_GFHDMI | AZX_DCAPS_POSFIX_LPIB | + AZX_DCAPS_NO_MSI | AZX_DCAPS_NO_64BIT }, /* VIA VT8251/VT8237A */ { PCI_DEVICE(0x1106, 0x3288), .driver_data = AZX_DRIVER_VIA }, /* VIA GFX VT7122/VX900 */ diff --git a/sound/pci/hda/patch_hdmi.c b/sound/pci/hda/patch_hdmi.c index 5c6980394dcec..b784ef95390db 100644 --- a/sound/pci/hda/patch_hdmi.c +++ b/sound/pci/hda/patch_hdmi.c @@ -4489,6 +4489,22 @@ static int patch_via_hdmi(struct hda_codec *codec) return patch_simple_hdmi(codec, VIAHDMI_CVT_NID, VIAHDMI_PIN_NID); } +static int patch_gf_hdmi(struct hda_codec *codec) +{ + int err; + + err = patch_generic_hdmi(codec); + if (err) + return err; + + /* + * Glenfly GPUs have two codecs, stream switches from one codec to + * another, need to do actual clean-ups in codec_cleanup_stream + */ + codec->no_sticky_stream = 1; + return 0; +} + /* * patch entries */ @@ -4579,6 +4595,12 @@ HDA_CODEC_ENTRY(0x10de009f, "GPU 9f HDMI/DP", patch_nvhdmi), HDA_CODEC_ENTRY(0x10de00a0, "GPU a0 HDMI/DP", patch_nvhdmi), HDA_CODEC_ENTRY(0x10de8001, "MCP73 HDMI", patch_nvhdmi_2ch), HDA_CODEC_ENTRY(0x10de8067, "MCP67/68 HDMI", patch_nvhdmi_2ch), +HDA_CODEC_ENTRY(0x67663d82, "Arise 82 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d83, "Arise 83 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d84, "Arise 84 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d85, "Arise 85 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d86, "Arise 86 HDMI/DP", patch_gf_hdmi), +HDA_CODEC_ENTRY(0x67663d87, "Arise 87 HDMI/DP", patch_gf_hdmi), HDA_CODEC_ENTRY(0x11069f80, "VX900 HDMI/DP", patch_via_hdmi), HDA_CODEC_ENTRY(0x11069f81, "VX900 HDMI/DP", patch_via_hdmi), HDA_CODEC_ENTRY(0x11069f84, "VX11 HDMI/DP", patch_generic_hdmi), -- 2.39.2

1 0

[PATCH AUTOSEL 6.3 10/11] ASoC: Intel: soc-acpi-cht: Add quirk for Nextbook Ares 8A tablet
by Sasha Levin 11 May '23

11 May '23

From: Hans de Goede <hdegoede(a)redhat.com> [ Upstream commit ec6f82b4c63cc68f8dc03316e725106d242706be ] The Nextbook Ares 8A tablet which has Android as factory OS, has a buggy DSDT with both ESSX8316 and 10EC5651 ACPI devices. This tablet actually uses an rt5651 codec, but the matching code ends up picking the ESSX8316 device, add a quirk to ignote the ESSX8316 device on this tablet. Signed-off-by: Hans de Goede <hdegoede(a)redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart(a)linux.intel.com> Message-Id: <20230429104721.7176-1-hdegoede(a)redhat.com> Signed-off-by: Mark Brown <broonie(a)kernel.org> Signed-off-by: Sasha Levin <sashal(a)kernel.org> --- .../intel/common/soc-acpi-intel-cht-match.c | 26 +++++++++++++++++++ 1 file changed, 26 insertions(+) diff --git a/sound/soc/intel/common/soc-acpi-intel-cht-match.c b/sound/soc/intel/common/soc-acpi-intel-cht-match.c index 6beb00858c33f..cdcbf04b8832f 100644 --- a/sound/soc/intel/common/soc-acpi-intel-cht-match.c +++ b/sound/soc/intel/common/soc-acpi-intel-cht-match.c @@ -50,6 +50,31 @@ static struct snd_soc_acpi_mach *cht_quirk(void *arg) return mach; } +/* + * Some tablets with Android factory OS have buggy DSDTs with an ESSX8316 device + * in the ACPI tables. While they are not using an ESS8316 codec. These DSDTs + * also have an ACPI device for the correct codec, ignore the ESSX8316. + */ +static const struct dmi_system_id cht_ess8316_not_present_table[] = { + { + /* Nextbook Ares 8A */ + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Insyde"), + DMI_MATCH(DMI_PRODUCT_NAME, "CherryTrail"), + DMI_MATCH(DMI_BIOS_VERSION, "M882"), + }, + }, + { } +}; + +static struct snd_soc_acpi_mach *cht_ess8316_quirk(void *arg) +{ + if (dmi_check_system(cht_ess8316_not_present_table)) + return NULL; + + return arg; +} + static const struct snd_soc_acpi_codecs rt5640_comp_ids = { .num_codecs = 2, .codecs = { "10EC5640", "10EC3276" }, @@ -113,6 +138,7 @@ struct snd_soc_acpi_mach snd_soc_acpi_intel_cherrytrail_machines[] = { .drv_name = "bytcht_es8316", .fw_filename = "intel/fw_sst_22a8.bin", .board = "bytcht_es8316", + .machine_quirk = cht_ess8316_quirk, .sof_tplg_filename = "sof-cht-es8316.tplg", }, /* some CHT-T platforms rely on RT5640, use Baytrail machine driver */ -- 2.39.2

1 0