February 2023 - Alsa-devel - mailman.alsa-project.org

[PATCH v2 1/4] ASoC: SMA1303: Remove the I2C Retry property in devicetree
by Kiseok Jo 09 Feb '23

09 Feb '23

It's necessary to set the value for each device, so remove that. Signed-off-by: Kiseok Jo <kiseok.jo(a)irondevice.com> --- sound/soc/codecs/sma1303.c | 16 +--------------- 1 file changed, 1 insertion(+), 15 deletions(-) diff --git a/sound/soc/codecs/sma1303.c b/sound/soc/codecs/sma1303.c index fbedba574ff4..fdcc40f5fc61 100644 --- a/sound/soc/codecs/sma1303.c +++ b/sound/soc/codecs/sma1303.c @@ -1621,21 +1621,6 @@ static int sma1303_i2c_probe(struct i2c_client *client) } if (np) { - if (!of_property_read_u32(np, "i2c-retry", &value)) { - if (value > 50 || value <= 0) { - sma1303->retry_cnt = SMA1303_I2C_RETRY_COUNT; - dev_dbg(&client->dev, "%s : %s\n", __func__, - "i2c-retry out of range (up to 50)"); - } else { - sma1303->retry_cnt = value; - dev_dbg(&client->dev, "%s : %s = %u\n", - __func__, "i2c-retry count", value); - } - } else { - dev_dbg(&client->dev, "%s : %s = %d\n", __func__, - "i2c-retry count", SMA1303_I2C_RETRY_COUNT); - sma1303->retry_cnt = SMA1303_I2C_RETRY_COUNT; - } if (!of_property_read_u32(np, "tdm-slot-rx", &value)) { dev_dbg(&client->dev, "tdm slot rx is '%d' from DT\n", value); @@ -1733,6 +1718,7 @@ static int sma1303_i2c_probe(struct i2c_client *client) sma1303->last_ocp_val = 0x08; sma1303->last_over_temp = 0xC0; sma1303->tsdw_cnt = 0; + sma1303->retry_cnt = SMA1303_I2C_RETRY_COUNT; sma1303->dev = &client->dev; sma1303->kobj = &client->dev.kobj; -- 2.20.1

4 8

[PATCH] ASoC: da7219: Fix pole orientation detection on OMTP headsets when playing music
by David Rau 09 Feb '23

09 Feb '23

The OMTP pin define headsets can be mis-detected as line out instead of OMTP, causing obvious issues with audio quality. This patch is to put increased resistances within the device at a suitable point. To solve this issue better, the new mechanism setup ground switches with conditional delay control and these allow for more stabile detection process to operate as intended. This conditional delay control will not impact the hardware process but use extra system resource. This commit improves control of ground switches in the AAD logic. Signed-off-by: David Rau <david.rau.zg(a)renesas.com> --- sound/soc/codecs/da7219-aad.c | 42 ++++++++++++++++++++++++++++++----- sound/soc/codecs/da7219-aad.h | 1 + 2 files changed, 37 insertions(+), 6 deletions(-) diff --git a/sound/soc/codecs/da7219-aad.c b/sound/soc/codecs/da7219-aad.c index bba73c44c219..08200ec259f9 100644 --- a/sound/soc/codecs/da7219-aad.c +++ b/sound/soc/codecs/da7219-aad.c @@ -352,9 +352,14 @@ static irqreturn_t da7219_aad_irq_thread(int irq, void *data) struct snd_soc_dapm_context *dapm = snd_soc_component_get_dapm(component); struct da7219_priv *da7219 = snd_soc_component_get_drvdata(component); u8 events[DA7219_AAD_IRQ_REG_MAX]; - u8 statusa; + u8 statusa, srm_st; int i, report = 0, mask = 0; + srm_st = snd_soc_component_read(component, DA7219_PLL_SRM_STS) & DA7219_PLL_SRM_STS_MCLK; + msleep(da7219_aad->gnd_switch_delay * ((srm_st == 0x0) ? 2 : 1) - 4); + /* Enable ground switch */ + snd_soc_component_update_bits(component, 0xFB, 0x01, 0x01); + /* Read current IRQ events */ regmap_bulk_read(da7219->regmap, DA7219_ACCDET_IRQ_EVENT_A, events, DA7219_AAD_IRQ_REG_MAX); @@ -454,8 +459,8 @@ static irqreturn_t da7219_aad_irq_thread(int irq, void *data) snd_soc_dapm_disable_pin(dapm, "Mic Bias"); snd_soc_dapm_sync(dapm); - /* Enable ground switch */ - snd_soc_component_update_bits(component, 0xFB, 0x01, 0x01); + /* Disable ground switch */ + snd_soc_component_update_bits(component, 0xFB, 0x01, 0x00); } } @@ -831,6 +836,32 @@ static void da7219_aad_handle_pdata(struct snd_soc_component *component) } } +static void da7219_aad_handle_gnd_switch_time(struct snd_soc_component *component) +{ + struct da7219_priv *da7219 = snd_soc_component_get_drvdata(component); + struct da7219_aad_priv *da7219_aad = da7219->aad; + u8 jack_det; + + jack_det = snd_soc_component_read(component, DA7219_ACCDET_CONFIG_2) + & DA7219_JACK_DETECT_RATE_MASK; + switch (jack_det) { + case 0x00: + da7219_aad->gnd_switch_delay = 32; + break; + case 0x10: + da7219_aad->gnd_switch_delay = 64; + break; + case 0x20: + da7219_aad->gnd_switch_delay = 128; + break; + case 0x30: + da7219_aad->gnd_switch_delay = 256; + break; + default: + da7219_aad->gnd_switch_delay = 32; + break; + } +} /* * Suspend/Resume @@ -908,9 +939,6 @@ int da7219_aad_init(struct snd_soc_component *component) snd_soc_component_update_bits(component, DA7219_ACCDET_CONFIG_1, DA7219_BUTTON_CONFIG_MASK, 0); - /* Enable ground switch */ - snd_soc_component_update_bits(component, 0xFB, 0x01, 0x01); - INIT_WORK(&da7219_aad->btn_det_work, da7219_aad_btn_det_work); INIT_WORK(&da7219_aad->hptest_work, da7219_aad_hptest_work); @@ -928,6 +956,8 @@ int da7219_aad_init(struct snd_soc_component *component) regmap_bulk_write(da7219->regmap, DA7219_ACCDET_IRQ_MASK_A, &mask, DA7219_AAD_IRQ_REG_MAX); + da7219_aad_handle_gnd_switch_time(component); + return 0; } EXPORT_SYMBOL_GPL(da7219_aad_init); diff --git a/sound/soc/codecs/da7219-aad.h b/sound/soc/codecs/da7219-aad.h index f48a12012ef3..21fdf53095cc 100644 --- a/sound/soc/codecs/da7219-aad.h +++ b/sound/soc/codecs/da7219-aad.h @@ -187,6 +187,7 @@ enum da7219_aad_event_regs { struct da7219_aad_priv { struct snd_soc_component *component; int irq; + int gnd_switch_delay; u8 micbias_pulse_lvl; u32 micbias_pulse_time; -- 2.17.1

4 21

[PATCH 0/2] ASoC: dt-bindings: renesas,rsnd.yaml: adjust to R-Car Gen4
by Kuninori Morimoto 09 Feb '23

09 Feb '23

Hi Mark, Rob, Krzysztof Cc Geert These are R-Car Gen4 support for Renesas sound driver. I have posted these patches as [RFC], because the schemas doesn't work correctly for me under certain conditions. "required: dmas/dma-names" always hits to "if-then" and never hits to "else" for some reasons. I'm still not sure why... But to be very strict, actually, this schemas is not mandatory, because there is PIO transfer mode which doesn't need to have DMA settings. Thus, this patch-set dropped the schemas for now, and ignore the issue, but it is *not* a wrong schemas IMO. Kuninori Morimoto (2): ASoC: dt-bindings: renesas,rsnd.yaml: tidyup reg/reg-name ASoC: dt-bindings: renesas,rsnd.yaml: adjust to R-Car Gen4 .../bindings/sound/renesas,rsnd.yaml | 76 ++++++++++++++----- 1 file changed, 56 insertions(+), 20 deletions(-) -- 2.25.1

3 7

[PATCH] ASoC: dt-bindings: wlf,wm8994: Convert to dtschema
by Krzysztof Kozlowski 08 Feb '23

08 Feb '23

Convert the Wolfson WM1811/WM8994/WM8958 audio codecs bindings to DT schema. Changes against original binding: 1. Add missing LDO1VDD-supply for WM1811. 2. Use "gpios" suffix for wlf,ldo1ena and wlf,ldo2ena (Linux kernel's gpiolib already looks for both variants). 3. Do not require AVDD1-supply and DCVDD-supply, because at least on Arndale board with Exynos5250 these are grounded. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski(a)linaro.org> --- .../devicetree/bindings/sound/wlf,wm8994.yaml | 203 ++++++++++++++++++ .../devicetree/bindings/sound/wm8994.txt | 112 ---------- 2 files changed, 203 insertions(+), 112 deletions(-) create mode 100644 Documentation/devicetree/bindings/sound/wlf,wm8994.yaml delete mode 100644 Documentation/devicetree/bindings/sound/wm8994.txt diff --git a/Documentation/devicetree/bindings/sound/wlf,wm8994.yaml b/Documentation/devicetree/bindings/sound/wlf,wm8994.yaml new file mode 100644 index 000000000000..24eabca7c173 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wlf,wm8994.yaml @@ -0,0 +1,203 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/wlf,wm8994.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Wolfson WM1811/WM8994/WM8958 audio codecs + +maintainers: + - Krzysztof Kozlowski <krzysztof.kozlowski(a)linaro.org> + - patches(a)opensource.cirrus.com + +description: | + These devices support both I2C and SPI (configured with pin strapping on the + board). + + Pins on the device (for linking into audio routes): + IN1LN, IN1LP, IN2LN, IN2LP:VXRN, IN1RN, IN1RP, IN2RN, IN2RP:VXRP, SPKOUTLP, + SPKOUTLN, SPKOUTRP, SPKOUTRN, HPOUT1L, HPOUT1R, HPOUT2P, HPOUT2N, LINEOUT1P, + LINEOUT1N, LINEOUT2P, LINEOUT2N. + +properties: + compatible: + enum: + - wlf,wm1811 + - wlf,wm8994 + - wlf,wm8958 + + reg: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + items: + - const: MCLK1 + - const: MCLK2 + + gpio-controller: true + + '#gpio-cells': + const: 2 + + interrupts: + maxItems: 1 + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + description: + The first cell is the IRQ number. The second cell is the flags, encoded + as the trigger masks. + + AVDD1-supply: true + AVDD2-supply: true + CPVDD-supply: true + DBVDD-supply: true + DBVDD1-supply: true + DBVDD2-supply: true + DBVDD3-supply: true + DCVDD-supply: true + LDO1VDD-supply: true + SPKVDD1-supply: true + SPKVDD2-supply: true + + '#sound-dai-cells': + const: 0 + + wlf,gpio-cfg: + $ref: /schemas/types.yaml#/definitions/uint32-array + maxItems: 11 + description: + A list of GPIO configuration register values. If absent, no configuration + of these registers is performed. If any value is over 0xffff then the + register will be left as default. If present 11 values must be supplied. + + wlf,micbias-cfg: + $ref: /schemas/types.yaml#/definitions/uint32-array + maxItems: 2 + description: + Two MICBIAS register values for WM1811 or WM8958. If absent the register + defaults will be used. + + wlf,ldo1ena-gpios: + maxItems: 1 + description: + Control of LDO1ENA input to device. + + wlf,ldo2ena-gpios: + maxItems: 1 + description: + Control of LDO2ENA input to device. + + wlf,lineout1-se: + type: boolean + description: + LINEOUT1 is in single ended mode. + + wlf,lineout2-se: + type: boolean + description: + INEOUT2 is in single ended mode. + + wlf,lineout1-feedback: + type: boolean + description: + LINEOUT1 has common mode feedback connected. + + wlf,lineout2-feedback: + type: boolean + description: + LINEOUT2 has common mode feedback connected. + + wlf,ldoena-always-driven: + type: boolean + description: + LDOENA is always driven. + + wlf,spkmode-pu: + type: boolean + description: + Enable the internal pull-up resistor on the SPKMODE pin. + + wlf,csnaddr-pd: + type: boolean + description: + Enable the internal pull-down resistor on the CS/ADDR pin. + +required: + - compatible + - reg + +allOf: + - $ref: dai-common.yaml# + - if: + properties: + compatible: + enum: + - wlf,wm1811 + - wlf,wm8958 + then: + properties: + DBVDD-supply: false + required: + - CPVDD-supply + - DBVDD1-supply + - DBVDD2-supply + - DBVDD3-supply + - SPKVDD1-supply + - SPKVDD2-supply + anyOf: + - required: + - AVDD1-supply + - required: + - AVDD2-supply + else: + properties: + DBVDD1-supply: false + DBVDD2-supply: false + DBVDD3-supply: false + required: + - AVDD1-supply + - AVDD2-supply + - CPVDD-supply + - DBVDD-supply + - DCVDD-supply + - SPKVDD1-supply + - SPKVDD2-supply + + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + audio-codec@1a { + compatible = "wlf,wm1811"; + reg = <0x1a>; + clocks = <&i2s0 0>; + clock-names = "MCLK1"; + + AVDD2-supply = <&main_dc_reg>; + CPVDD-supply = <&main_dc_reg>; + DBVDD1-supply = <&main_dc_reg>; + DBVDD2-supply = <&main_dc_reg>; + DBVDD3-supply = <&main_dc_reg>; + LDO1VDD-supply = <&main_dc_reg>; + SPKVDD1-supply = <&main_dc_reg>; + SPKVDD2-supply = <&main_dc_reg>; + + wlf,ldo1ena-gpios = <&gpb0 0 GPIO_ACTIVE_HIGH>; + wlf,ldo2ena-gpios = <&gpb0 1 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/sound/wm8994.txt b/Documentation/devicetree/bindings/sound/wm8994.txt deleted file mode 100644 index 8fa947509c10..000000000000 --- a/Documentation/devicetree/bindings/sound/wm8994.txt +++ /dev/null @@ -1,112 +0,0 @@ -WM1811/WM8994/WM8958 audio CODEC - -These devices support both I2C and SPI (configured with pin strapping -on the board). - -Required properties: - - - compatible : One of "wlf,wm1811", "wlf,wm8994" or "wlf,wm8958". - - - reg : the I2C address of the device for I2C, the chip select - number for SPI. - - - gpio-controller : Indicates this device is a GPIO controller. - - #gpio-cells : Must be 2. The first cell is the pin number and the - second cell is used to specify optional parameters (currently unused). - - - power supplies for the device, as covered in - Documentation/devicetree/bindings/regulator/regulator.txt, depending - on compatible: - - for wlf,wm1811 and wlf,wm8958: - AVDD1-supply, AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, - DCVDD-supply, CPVDD-supply, SPKVDD1-supply, SPKVDD2-supply - - for wlf,wm8994: - AVDD1-supply, AVDD2-supply, DBVDD-supply, DCVDD-supply, CPVDD-supply, - SPKVDD1-supply, SPKVDD2-supply - -Optional properties: - - - interrupts : The interrupt line the IRQ signal for the device is - connected to. This is optional, if it is not connected then none - of the interrupt related properties should be specified. - - interrupt-controller : These devices contain interrupt controllers - and may provide interrupt services to other devices if they have an - interrupt line connected. - - #interrupt-cells: the number of cells to describe an IRQ, this should be 2. - The first cell is the IRQ number. - The second cell is the flags, encoded as the trigger masks from - Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - - - clocks : A list of up to two phandle and clock specifier pairs - - clock-names : A list of clock names sorted in the same order as clocks. - Valid clock names are "MCLK1" and "MCLK2". - - - wlf,gpio-cfg : A list of GPIO configuration register values. If absent, - no configuration of these registers is performed. If any value is - over 0xffff then the register will be left as default. If present 11 - values must be supplied. - - - wlf,micbias-cfg : Two MICBIAS register values for WM1811 or - WM8958. If absent the register defaults will be used. - - - wlf,ldo1ena : GPIO specifier for control of LDO1ENA input to device. - - wlf,ldo2ena : GPIO specifier for control of LDO2ENA input to device. - - - wlf,lineout1-se : If present LINEOUT1 is in single ended mode. - - wlf,lineout2-se : If present LINEOUT2 is in single ended mode. - - - wlf,lineout1-feedback : If present LINEOUT1 has common mode feedback - connected. - - wlf,lineout2-feedback : If present LINEOUT2 has common mode feedback - connected. - - - wlf,ldoena-always-driven : If present LDOENA is always driven. - - - wlf,spkmode-pu : If present enable the internal pull-up resistor on - the SPKMODE pin. - - - wlf,csnaddr-pd : If present enable the internal pull-down resistor on - the CS/ADDR pin. - -Pins on the device (for linking into audio routes): - - * IN1LN - * IN1LP - * IN2LN - * IN2LP:VXRN - * IN1RN - * IN1RP - * IN2RN - * IN2RP:VXRP - * SPKOUTLP - * SPKOUTLN - * SPKOUTRP - * SPKOUTRN - * HPOUT1L - * HPOUT1R - * HPOUT2P - * HPOUT2N - * LINEOUT1P - * LINEOUT1N - * LINEOUT2P - * LINEOUT2N - -Example: - -wm8994: codec@1a { - compatible = "wlf,wm8994"; - reg = <0x1a>; - - gpio-controller; - #gpio-cells = <2>; - - lineout1-se; - - AVDD1-supply = <&regulator>; - AVDD2-supply = <&regulator>; - CPVDD-supply = <&regulator>; - DBVDD-supply = <&regulator>; - DCVDD-supply = <&regulator>; - SPKVDD1-supply = <&regulator>; - SPKVDD2-supply = <&regulator>; -}; -- 2.34.1

3 8

[PATCH v3 0/1] ASoC: dt-bindings: meson: covert axg audio to schema
by Jerome Brunet 08 Feb '23

08 Feb '23

Continue conversion of AXG audio dt-binding documentation to schema Changes since v2: * Drop 6 patches applied with v2 * Drop Yaml block style indicator for multiline description Changes since v1: * Drop 2 patches applied with v1 * Drop node name patterns * Fix examples indentation * Yaml fixups requested by Krzysztof Jerome Brunet (1): ASoC: dt-bindings: meson: convert axg sound card control to schema .../bindings/sound/amlogic,axg-sound-card.txt | 124 ------------ .../sound/amlogic,axg-sound-card.yaml | 183 ++++++++++++++++++ 2 files changed, 183 insertions(+), 124 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sound/amlogic,axg-sound-card.txt create mode 100644 Documentation/devicetree/bindings/sound/amlogic,axg-sound-card.yaml -- 2.39.1

3 5

[PATCH v3 0/4] Add CS35L41 shared boost feature
by Lucas Tanure 08 Feb '23

08 Feb '23

Valve's Steam Deck uses CS35L41 in shared boost mode, where both speakers share the boost circuit. Add this support in the shared lib, but for now, shared boost is not supported in HDA systems as would require BIOS changes. Based on David Rhodes shared boost patches. Also, fix boost config overwriting in IRQ found in the review and do a small refactor of the code. Changes from V2: - Drop External boost without VSPK Documentation - Move Shared boost to use values 2 and 3 - Revert back to reg_sequence but reading the value first and only update the necessary bits - Fix bug found by Intel kernel Test Robot Changes from V1: - Fix Documentation patch subject - New patch for External boost without VSPK Documentation - New patch to fix boost IRQ overwriting issue - New patch to refactor IRQ release error code - reinit_completion on pcm_startup - fix DRE switch overwriting - return IRQ_HANDLED in PLL_LOCK case Lucas Tanure (4): ASoC: cs35l41: Only disable internal boost ASoC: cs35l41: Refactor error release code ALSA: cs35l41: Add shared boost feature ASoC: cs35l41: Document CS35l41 shared boost .../bindings/sound/cirrus,cs35l41.yaml | 10 +- include/sound/cs35l41.h | 13 +- sound/pci/hda/cs35l41_hda.c | 6 +- sound/soc/codecs/cs35l41-lib.c | 69 +++++++++- sound/soc/codecs/cs35l41.c | 125 +++++++++--------- sound/soc/codecs/cs35l41.h | 1 + 6 files changed, 153 insertions(+), 71 deletions(-) -- 2.39.1

3 6

[PATCH] ASoC: SOF: ops: refine parameters order in function snd_sof_dsp_update8
by Peter Ujfalusi 08 Feb '23

08 Feb '23

From: Rander Wang <rander.wang(a)intel.com> SOF driver calls snd_sof_dsp_update8 with parameters mask and value but the snd_sof_dsp_update8 declares these two parameters in reverse order. This causes some issues such as d0i3 register can't be set correctly Now change function definition according to common SOF usage. Fixes: c28a36b012f1 ("ASoC: SOF: ops: add snd_sof_dsp_updateb() helper") Signed-off-by: Rander Wang <rander.wang(a)intel.com> Reviewed-by: Bard Liao <yung-chuan.liao(a)linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan(a)linux.intel.com> Reviewed-by: Chao Song <chao.song(a)linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi(a)linux.intel.com> Reviewed-by: Liam Girdwood <liam.r.girdwood(a)intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart(a)linux.intel.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi(a)linux.intel.com> --- Hi Mark, Can you take this one for the next 6.2-rc? Commit c28a36b012f1 is introduced in 6.2-rc1. Thank you, Peter sound/soc/sof/ops.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/sof/ops.h b/sound/soc/sof/ops.h index 03752c8405ca..9ab7b9be765b 100644 --- a/sound/soc/sof/ops.h +++ b/sound/soc/sof/ops.h @@ -357,7 +357,7 @@ static inline u64 snd_sof_dsp_read64(struct snd_sof_dev *sdev, u32 bar, } static inline void snd_sof_dsp_update8(struct snd_sof_dev *sdev, u32 bar, - u32 offset, u8 value, u8 mask) + u32 offset, u8 mask, u8 value) { u8 reg; -- 2.39.1

2 1

[PATCH 0/3] ALSA: core: Make some functions return void
by Uwe Kleine-König 08 Feb '23

08 Feb '23

Hello, while checking in which cases hda_tegra_remove() can return a non-zero value, I found that actually cannot happen. This series makes the involved functions return void to make this obvious. This is a preparation for making platform_driver::remove return void, too. Best regards Uwe Uwe Kleine-König (3): ALSA: core: Make snd_card_disconnect() return void ALSA: core: Make snd_card_free_when_closed() return void ALSA: core: Make snd_card_free() return void include/sound/core.h | 6 +++--- sound/core/init.c | 40 ++++++++++++++------------------------- sound/pci/hda/hda_tegra.c | 6 ++---- sound/ppc/snd_ps3.c | 4 +--- 4 files changed, 20 insertions(+), 36 deletions(-) base-commit: 05ecb680708a1dbe6554d6fc17e5d9a8a7cb5e6a -- 2.39.0

6 9

[PATCH v2 0/5] Add CS35L41 shared boost feature
by Lucas Tanure 08 Feb '23

08 Feb '23

Valve's Steam Deck uses CS35L41 in shared boost mode, where both speakers share the boost circuit. Add this support in the shared lib, but for now, shared boost is not supported in HDA systems as would require BIOS changes. Based on David Rhodes shared boost patches. Also, fix boost config overwriting in IRQ found in the review and do a small refactor of the code. Changes from V1: - Fix Documentation patch subject - New patch for External boost without VSPK Documentation - New patch to fix boost IRQ overwriting issue - New patch to refactor IRQ release error code - reinit_completion on pcm_startup - fix DRE switch overwriting - return IRQ_HANDLED in PLL_LOCK case Lucas Tanure (5): ASoC: cs35l41: Only disable internal boost ASoC: cs35l41: Refactor error release code ALSA: cs35l41: Add shared boost feature ASoC: cs35l41: Document CS35l41 external boost without VSPK ASoC: cs35l41: Document CS35l41 shared boost .../bindings/sound/cirrus,cs35l41.yaml | 12 +- include/sound/cs35l41.h | 10 +- sound/pci/hda/cs35l41_hda.c | 6 +- sound/soc/codecs/cs35l41-lib.c | 56 +++++++- sound/soc/codecs/cs35l41.c | 125 +++++++++--------- sound/soc/codecs/cs35l41.h | 1 + 6 files changed, 139 insertions(+), 71 deletions(-) -- 2.39.1

4 10

Re: [PATCH 1/2] ALSA: cs35l41: Add shared boost feature
by kernel test robot 08 Feb '23

08 Feb '23

Hi Lucas, I love your patch! Perhaps something to improve: [auto build test WARNING on broonie-sound/for-next] [also build test WARNING on tiwai-sound/for-next tiwai-sound/for-linus linus/master v6.2-rc7 next-20230208] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch#_base_tree_information] url: https://github.com/intel-lab-lkp/linux/commits/Lucas-Tanure/ALSA-cs35l41-Ad… base: https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next patch link: https://lore.kernel.org/r/20230207104021.2842-2-lucas.tanure%40collabora.com patch subject: [PATCH 1/2] ALSA: cs35l41: Add shared boost feature config: i386-randconfig-a011 (https://download.01.org/0day-ci/archive/20230208/202302081911.MDwfUTfx-lkp@…) compiler: clang version 14.0.6 (https://github.com/llvm/llvm-project f28c006a5895fc0e329fe15fead81e37457cb1d1) reproduce (this is a W=1 build): wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross # https://github.com/intel-lab-lkp/linux/commit/c1726800667180cd46986c3578e63… git remote add linux-review https://github.com/intel-lab-lkp/linux git fetch --no-tags linux-review Lucas-Tanure/ALSA-cs35l41-Add-shared-boost-feature/20230207-184238 git checkout c1726800667180cd46986c3578e635bafa8bf01a # save the config file mkdir build_dir && cp config build_dir/.config COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross W=1 O=build_dir ARCH=i386 olddefconfig COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross W=1 O=build_dir ARCH=i386 SHELL=/bin/bash sound/soc/codecs/ If you fix the issue, kindly add following tag where applicable | Reported-by: kernel test robot <lkp(a)intel.com> All warnings (new ones prefixed by >>): >> sound/soc/codecs/cs35l41-lib.c:1160:7: warning: variable 'ret' is used uninitialized whenever switch case is taken [-Wsometimes-uninitialized] case CS35L41_SHD_BOOST_PASS: ^~~~~~~~~~~~~~~~~~~~~~ sound/soc/codecs/cs35l41-lib.c:1169:9: note: uninitialized use occurs here return ret; ^~~ sound/soc/codecs/cs35l41-lib.c:1136:9: note: initialize the variable 'ret' to silence this warning int ret; ^ = 0 1 warning generated. vim +/ret +1160 sound/soc/codecs/cs35l41-lib.c 1132 1133 int cs35l41_init_boost(struct device *dev, struct regmap *regmap, 1134 struct cs35l41_hw_cfg *hw_cfg) 1135 { 1136 int ret; 1137 1138 switch (hw_cfg->bst_type) { 1139 case CS35L41_SHD_BOOST_ACTV: 1140 regmap_multi_reg_write(regmap, cs35l41_actv_seq, ARRAY_SIZE(cs35l41_actv_seq)); 1141 fallthrough; 1142 case CS35L41_INT_BOOST: 1143 ret = cs35l41_boost_config(dev, regmap, hw_cfg->bst_ind, 1144 hw_cfg->bst_cap, hw_cfg->bst_ipk); 1145 if (ret) 1146 dev_err(dev, "Error in Boost DT config: %d\n", ret); 1147 break; 1148 case CS35L41_EXT_BOOST: 1149 case CS35L41_EXT_BOOST_NO_VSPK_SWITCH: 1150 /* Only CLSA0100 doesn't use GPIO as VSPK switch, but even on that laptop we can 1151 * toggle GPIO1 as is not connected to anything. 1152 * There will be no other device without VSPK switch. 1153 */ 1154 regmap_write(regmap, CS35L41_GPIO1_CTRL1, 0x00000001); 1155 regmap_multi_reg_write(regmap, cs35l41_reset_to_safe, 1156 ARRAY_SIZE(cs35l41_reset_to_safe)); 1157 ret = regmap_update_bits(regmap, CS35L41_PWR_CTRL2, CS35L41_BST_EN_MASK, 1158 CS35L41_BST_DIS_FET_OFF << CS35L41_BST_EN_SHIFT); 1159 break; > 1160 case CS35L41_SHD_BOOST_PASS: 1161 regmap_multi_reg_write(regmap, cs35l41_pass_seq, ARRAY_SIZE(cs35l41_pass_seq)); 1162 break; 1163 default: 1164 dev_err(dev, "Boost type %d not supported\n", hw_cfg->bst_type); 1165 ret = -EINVAL; 1166 break; 1167 } 1168 1169 return ret; 1170 } 1171 EXPORT_SYMBOL_GPL(cs35l41_init_boost); 1172 -- 0-DAY CI Kernel Test Service https://github.com/intel/lkp-tests

1 0