April 2022 - Alsa-devel - mailman.alsa-project.org

[PATCH] ASoC: qcom: SC7280: Update machine driver startup, shutdown callbacks
by Srinivasa Rao Mandadapu 19 Apr '22

19 Apr '22

Update machine driver startup, shutdown callback functions to support codec DMA paths. Without this change, platforms with WCD codec is failing to register sound card. Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam(a)quicinc.com> Co-developed-by: Venkata Prasad Potturu <quic_potturu(a)quicinc.com> Signed-off-by: Venkata Prasad Potturu <quic_potturu(a)quicinc.com> --- sound/soc/qcom/sc7280.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/sound/soc/qcom/sc7280.c b/sound/soc/qcom/sc7280.c index 4ef4034..d64df11 100644 --- a/sound/soc/qcom/sc7280.c +++ b/sound/soc/qcom/sc7280.c @@ -295,6 +295,10 @@ static void sc7280_snd_shutdown(struct snd_pcm_substream *substream) break; case LPASS_DP_RX: break; + case LPASS_CDC_DMA_RX0 ... LPASS_CDC_DMA_RX9: + case LPASS_CDC_DMA_TX0 ... LPASS_CDC_DMA_TX8: + case LPASS_CDC_DMA_VA_TX0 ... LPASS_CDC_DMA_VA_TX8: + break; default: dev_err(rtd->dev, "%s: invalid dai id 0x%x\n", __func__, cpu_dai->id); @@ -316,6 +320,10 @@ static int sc7280_snd_startup(struct snd_pcm_substream *substream) break; case LPASS_DP_RX: break; + case LPASS_CDC_DMA_RX0 ... LPASS_CDC_DMA_RX9: + case LPASS_CDC_DMA_TX0 ... LPASS_CDC_DMA_TX8: + case LPASS_CDC_DMA_VA_TX0 ... LPASS_CDC_DMA_VA_TX8: + break; default: dev_err(rtd->dev, "%s: invalid dai id 0x%x\n", __func__, cpu_dai->id); -- 2.7.4

2 2

[PATCH 0/2] Fix apq8016 compat string
by Bryan O'Donoghue 19 Apr '22

19 Apr '22

Reusing the apq8016 on msm8939 I found running checkpatch that the compat string for the LPASS was throwing a warning. This is easily fixed by alinging the YAML, DTS and driver to the documented compat string - compatible = "qcom,lpass-cpu-apq8016"; + compatible = "qcom,apq8016-lpass-cpu"; Bryan O'Donoghue (2): ASoC: qcom: lpass: Fix apq8016 compat string to match yaml arm64: dts: qcom: Fix apq8016 compat string to match yaml arch/arm64/boot/dts/qcom/msm8916.dtsi | 2 +- sound/soc/qcom/lpass-apq8016.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) -- 2.35.1

2 3

[PATCH -next] slimbus: qcom: Remove unnecessary print function dev_err()
by Yang Li 19 Apr '22

19 Apr '22

The print function dev_err() is redundant because platform_get_irq_byname() already prints an error. Eliminate the follow coccicheck warning: ./drivers/slimbus/qcom-ctrl.c:514:2-9: line 514 is redundant because platform_get_irq() already prints an error Reported-by: Abaci Robot <abaci(a)linux.alibaba.com> Signed-off-by: Yang Li <yang.lee(a)linux.alibaba.com> --- drivers/slimbus/qcom-ctrl.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/drivers/slimbus/qcom-ctrl.c b/drivers/slimbus/qcom-ctrl.c index ec58091fc948..c0c4f895d76e 100644 --- a/drivers/slimbus/qcom-ctrl.c +++ b/drivers/slimbus/qcom-ctrl.c @@ -510,10 +510,8 @@ static int qcom_slim_probe(struct platform_device *pdev) } ctrl->irq = platform_get_irq(pdev, 0); - if (ctrl->irq < 0) { - dev_err(&pdev->dev, "no slimbus IRQ\n"); + if (ctrl->irq < 0) return ctrl->irq; - } sctrl = &ctrl->ctrl; sctrl->dev = &pdev->dev; -- 2.20.1.7.g153144c

2 1

[PATCH] m68k: coldfire: drop ISA_DMA_API support
by Arnd Bergmann 19 Apr '22

19 Apr '22

From: Arnd Bergmann <arnd(a)arndb.de> After a build regression report, I took a look at possible users of CONFIG_ISA_DMA_API on m68k and found none, which Greg confirmed. With no reason to keep this, let's just drop the corresponding files and prevent the remaining ISA drivers that use this from getting built. The remaining definitions in asm/dma.h are used for PCI support. Link: https://lore.kernel.org/lkml/9e5ee1c3-ca80-f343-a1f5-66f3dd1c0727@linux-m68… Cc: Greg Ungerer <gerg(a)linux-m68k.org> Signed-off-by: Arnd Bergmann <arnd(a)arndb.de> --- arch/m68k/Kconfig.bus | 7 - arch/m68k/coldfire/dma.c | 43 ---- arch/m68k/include/asm/dma.h | 478 ------------------------------------ arch/m68k/mm/motorola.c | 1 - drivers/mmc/host/Kconfig | 2 +- sound/core/Makefile | 2 - sound/isa/Kconfig | 2 +- 7 files changed, 2 insertions(+), 533 deletions(-) delete mode 100644 arch/m68k/coldfire/dma.c diff --git a/arch/m68k/Kconfig.bus b/arch/m68k/Kconfig.bus index d1e93a39cd3b..197b806bfa60 100644 --- a/arch/m68k/Kconfig.bus +++ b/arch/m68k/Kconfig.bus @@ -62,10 +62,3 @@ config GENERIC_ISA_DMA source "drivers/zorro/Kconfig" endif - -if COLDFIRE - -config ISA_DMA_API - def_bool !M5272 - -endif diff --git a/arch/m68k/coldfire/dma.c b/arch/m68k/coldfire/dma.c deleted file mode 100644 index c3279f7467d7..000000000000 --- a/arch/m68k/coldfire/dma.c +++ /dev/null @@ -1,43 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/***************************************************************************/ - -/* - * dma.c -- Freescale ColdFire DMA support - * - * Copyright (C) 2007, Greg Ungerer (gerg(a)snapgear.com) - */ - -/***************************************************************************/ - -#include <linux/kernel.h> -#include <linux/module.h> -#include <asm/dma.h> -#include <asm/coldfire.h> -#include <asm/mcfsim.h> -#include <asm/mcfdma.h> - -/***************************************************************************/ - -/* - * DMA channel base address table. - */ -unsigned int dma_base_addr[MAX_M68K_DMA_CHANNELS] = { -#ifdef MCFDMA_BASE0 - MCFDMA_BASE0, -#endif -#ifdef MCFDMA_BASE1 - MCFDMA_BASE1, -#endif -#ifdef MCFDMA_BASE2 - MCFDMA_BASE2, -#endif -#ifdef MCFDMA_BASE3 - MCFDMA_BASE3, -#endif -}; -EXPORT_SYMBOL(dma_base_addr); - -unsigned int dma_device_address[MAX_M68K_DMA_CHANNELS]; -EXPORT_SYMBOL(dma_device_address); - -/***************************************************************************/ diff --git a/arch/m68k/include/asm/dma.h b/arch/m68k/include/asm/dma.h index ae2021964e32..2cb361dede24 100644 --- a/arch/m68k/include/asm/dma.h +++ b/arch/m68k/include/asm/dma.h @@ -2,484 +2,6 @@ #ifndef _M68K_DMA_H #define _M68K_DMA_H 1 -#ifdef CONFIG_COLDFIRE -/* - * ColdFire DMA Model: - * ColdFire DMA supports two forms of DMA: Single and Dual address. Single - * address mode emits a source address, and expects that the device will either - * pick up the data (DMA READ) or source data (DMA WRITE). This implies that - * the device will place data on the correct byte(s) of the data bus, as the - * memory transactions are always 32 bits. This implies that only 32 bit - * devices will find single mode transfers useful. Dual address DMA mode - * performs two cycles: source read and destination write. ColdFire will - * align the data so that the device will always get the correct bytes, thus - * is useful for 8 and 16 bit devices. This is the mode that is supported - * below. - * - * AUG/22/2000 : added support for 32-bit Dual-Address-Mode (K) 2000 - * Oliver Kamphenkel (O.Kamphenkel(a)tu-bs.de) - * - * AUG/25/2000 : added support for 8, 16 and 32-bit Single-Address-Mode (K)2000 - * Oliver Kamphenkel (O.Kamphenkel(a)tu-bs.de) - * - * APR/18/2002 : added proper support for MCF5272 DMA controller. - * Arthur Shipkowski (art(a)videon-central.com) - */ - -#include <asm/coldfire.h> -#include <asm/mcfsim.h> -#include <asm/mcfdma.h> - -/* - * Set number of channels of DMA on ColdFire for different implementations. - */ -#if defined(CONFIG_M5249) || defined(CONFIG_M5307) || defined(CONFIG_M5407) || \ - defined(CONFIG_M523x) || defined(CONFIG_M527x) || \ - defined(CONFIG_M528x) || defined(CONFIG_M525x) - -#define MAX_M68K_DMA_CHANNELS 4 -#elif defined(CONFIG_M5272) -#define MAX_M68K_DMA_CHANNELS 1 -#elif defined(CONFIG_M53xx) -#define MAX_M68K_DMA_CHANNELS 0 -#else -#define MAX_M68K_DMA_CHANNELS 2 -#endif - -extern unsigned int dma_base_addr[MAX_M68K_DMA_CHANNELS]; -extern unsigned int dma_device_address[MAX_M68K_DMA_CHANNELS]; - -#if !defined(CONFIG_M5272) -#define DMA_MODE_WRITE_BIT 0x01 /* Memory/IO to IO/Memory select */ -#define DMA_MODE_WORD_BIT 0x02 /* 8 or 16 bit transfers */ -#define DMA_MODE_LONG_BIT 0x04 /* or 32 bit transfers */ -#define DMA_MODE_SINGLE_BIT 0x08 /* single-address-mode */ - -/* I/O to memory, 8 bits, mode */ -#define DMA_MODE_READ 0 -/* memory to I/O, 8 bits, mode */ -#define DMA_MODE_WRITE 1 -/* I/O to memory, 16 bits, mode */ -#define DMA_MODE_READ_WORD 2 -/* memory to I/O, 16 bits, mode */ -#define DMA_MODE_WRITE_WORD 3 -/* I/O to memory, 32 bits, mode */ -#define DMA_MODE_READ_LONG 4 -/* memory to I/O, 32 bits, mode */ -#define DMA_MODE_WRITE_LONG 5 -/* I/O to memory, 8 bits, single-address-mode */ -#define DMA_MODE_READ_SINGLE 8 -/* memory to I/O, 8 bits, single-address-mode */ -#define DMA_MODE_WRITE_SINGLE 9 -/* I/O to memory, 16 bits, single-address-mode */ -#define DMA_MODE_READ_WORD_SINGLE 10 -/* memory to I/O, 16 bits, single-address-mode */ -#define DMA_MODE_WRITE_WORD_SINGLE 11 -/* I/O to memory, 32 bits, single-address-mode */ -#define DMA_MODE_READ_LONG_SINGLE 12 -/* memory to I/O, 32 bits, single-address-mode */ -#define DMA_MODE_WRITE_LONG_SINGLE 13 - -#else /* CONFIG_M5272 is defined */ - -/* Source static-address mode */ -#define DMA_MODE_SRC_SA_BIT 0x01 -/* Two bits to select between all four modes */ -#define DMA_MODE_SSIZE_MASK 0x06 -/* Offset to shift bits in */ -#define DMA_MODE_SSIZE_OFF 0x01 -/* Destination static-address mode */ -#define DMA_MODE_DES_SA_BIT 0x10 -/* Two bits to select between all four modes */ -#define DMA_MODE_DSIZE_MASK 0x60 -/* Offset to shift bits in */ -#define DMA_MODE_DSIZE_OFF 0x05 -/* Size modifiers */ -#define DMA_MODE_SIZE_LONG 0x00 -#define DMA_MODE_SIZE_BYTE 0x01 -#define DMA_MODE_SIZE_WORD 0x02 -#define DMA_MODE_SIZE_LINE 0x03 - -/* - * Aliases to help speed quick ports; these may be suboptimal, however. They - * do not include the SINGLE mode modifiers since the MCF5272 does not have a - * mode where the device is in control of its addressing. - */ - -/* I/O to memory, 8 bits, mode */ -#define DMA_MODE_READ ((DMA_MODE_SIZE_BYTE << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_BYTE << DMA_MODE_SSIZE_OFF) | DMA_SRC_SA_BIT) -/* memory to I/O, 8 bits, mode */ -#define DMA_MODE_WRITE ((DMA_MODE_SIZE_BYTE << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_BYTE << DMA_MODE_SSIZE_OFF) | DMA_DES_SA_BIT) -/* I/O to memory, 16 bits, mode */ -#define DMA_MODE_READ_WORD ((DMA_MODE_SIZE_WORD << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_WORD << DMA_MODE_SSIZE_OFF) | DMA_SRC_SA_BIT) -/* memory to I/O, 16 bits, mode */ -#define DMA_MODE_WRITE_WORD ((DMA_MODE_SIZE_WORD << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_WORD << DMA_MODE_SSIZE_OFF) | DMA_DES_SA_BIT) -/* I/O to memory, 32 bits, mode */ -#define DMA_MODE_READ_LONG ((DMA_MODE_SIZE_LONG << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_LONG << DMA_MODE_SSIZE_OFF) | DMA_SRC_SA_BIT) -/* memory to I/O, 32 bits, mode */ -#define DMA_MODE_WRITE_LONG ((DMA_MODE_SIZE_LONG << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_LONG << DMA_MODE_SSIZE_OFF) | DMA_DES_SA_BIT) - -#endif /* !defined(CONFIG_M5272) */ - -#if !defined(CONFIG_M5272) -/* enable/disable a specific DMA channel */ -static __inline__ void enable_dma(unsigned int dmanr) -{ - volatile unsigned short *dmawp; - -#ifdef DMA_DEBUG - printk("enable_dma(dmanr=%d)\n", dmanr); -#endif - - dmawp = (unsigned short *) dma_base_addr[dmanr]; - dmawp[MCFDMA_DCR] |= MCFDMA_DCR_EEXT; -} - -static __inline__ void disable_dma(unsigned int dmanr) -{ - volatile unsigned short *dmawp; - volatile unsigned char *dmapb; - -#ifdef DMA_DEBUG - printk("disable_dma(dmanr=%d)\n", dmanr); -#endif - - dmawp = (unsigned short *) dma_base_addr[dmanr]; - dmapb = (unsigned char *) dma_base_addr[dmanr]; - - /* Turn off external requests, and stop any DMA in progress */ - dmawp[MCFDMA_DCR] &= ~MCFDMA_DCR_EEXT; - dmapb[MCFDMA_DSR] = MCFDMA_DSR_DONE; -} - -/* - * Clear the 'DMA Pointer Flip Flop'. - * Write 0 for LSB/MSB, 1 for MSB/LSB access. - * Use this once to initialize the FF to a known state. - * After that, keep track of it. :-) - * --- In order to do that, the DMA routines below should --- - * --- only be used while interrupts are disabled! --- - * - * This is a NOP for ColdFire. Provide a stub for compatibility. - */ -static __inline__ void clear_dma_ff(unsigned int dmanr) -{ -} - -/* set mode (above) for a specific DMA channel */ -static __inline__ void set_dma_mode(unsigned int dmanr, char mode) -{ - - volatile unsigned char *dmabp; - volatile unsigned short *dmawp; - -#ifdef DMA_DEBUG - printk("set_dma_mode(dmanr=%d,mode=%d)\n", dmanr, mode); -#endif - - dmabp = (unsigned char *) dma_base_addr[dmanr]; - dmawp = (unsigned short *) dma_base_addr[dmanr]; - - /* Clear config errors */ - dmabp[MCFDMA_DSR] = MCFDMA_DSR_DONE; - - /* Set command register */ - dmawp[MCFDMA_DCR] = - MCFDMA_DCR_INT | /* Enable completion irq */ - MCFDMA_DCR_CS | /* Force one xfer per request */ - MCFDMA_DCR_AA | /* Enable auto alignment */ - /* single-address-mode */ - ((mode & DMA_MODE_SINGLE_BIT) ? MCFDMA_DCR_SAA : 0) | - /* sets s_rw (-> r/w) high if Memory to I/0 */ - ((mode & DMA_MODE_WRITE_BIT) ? MCFDMA_DCR_S_RW : 0) | - /* Memory to I/O or I/O to Memory */ - ((mode & DMA_MODE_WRITE_BIT) ? MCFDMA_DCR_SINC : MCFDMA_DCR_DINC) | - /* 32 bit, 16 bit or 8 bit transfers */ - ((mode & DMA_MODE_WORD_BIT) ? MCFDMA_DCR_SSIZE_WORD : - ((mode & DMA_MODE_LONG_BIT) ? MCFDMA_DCR_SSIZE_LONG : - MCFDMA_DCR_SSIZE_BYTE)) | - ((mode & DMA_MODE_WORD_BIT) ? MCFDMA_DCR_DSIZE_WORD : - ((mode & DMA_MODE_LONG_BIT) ? MCFDMA_DCR_DSIZE_LONG : - MCFDMA_DCR_DSIZE_BYTE)); - -#ifdef DEBUG_DMA - printk("%s(%d): dmanr=%d DSR[%x]=%x DCR[%x]=%x\n", __FILE__, __LINE__, - dmanr, (int) &dmabp[MCFDMA_DSR], dmabp[MCFDMA_DSR], - (int) &dmawp[MCFDMA_DCR], dmawp[MCFDMA_DCR]); -#endif -} - -/* Set transfer address for specific DMA channel */ -static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a) -{ - volatile unsigned short *dmawp; - volatile unsigned int *dmalp; - -#ifdef DMA_DEBUG - printk("set_dma_addr(dmanr=%d,a=%x)\n", dmanr, a); -#endif - - dmawp = (unsigned short *) dma_base_addr[dmanr]; - dmalp = (unsigned int *) dma_base_addr[dmanr]; - - /* Determine which address registers are used for memory/device accesses */ - if (dmawp[MCFDMA_DCR] & MCFDMA_DCR_SINC) { - /* Source incrementing, must be memory */ - dmalp[MCFDMA_SAR] = a; - /* Set dest address, must be device */ - dmalp[MCFDMA_DAR] = dma_device_address[dmanr]; - } else { - /* Destination incrementing, must be memory */ - dmalp[MCFDMA_DAR] = a; - /* Set source address, must be device */ - dmalp[MCFDMA_SAR] = dma_device_address[dmanr]; - } - -#ifdef DEBUG_DMA - printk("%s(%d): dmanr=%d DCR[%x]=%x SAR[%x]=%08x DAR[%x]=%08x\n", - __FILE__, __LINE__, dmanr, (int) &dmawp[MCFDMA_DCR], dmawp[MCFDMA_DCR], - (int) &dmalp[MCFDMA_SAR], dmalp[MCFDMA_SAR], - (int) &dmalp[MCFDMA_DAR], dmalp[MCFDMA_DAR]); -#endif -} - -/* - * Specific for Coldfire - sets device address. - * Should be called after the mode set call, and before set DMA address. - */ -static __inline__ void set_dma_device_addr(unsigned int dmanr, unsigned int a) -{ -#ifdef DMA_DEBUG - printk("set_dma_device_addr(dmanr=%d,a=%x)\n", dmanr, a); -#endif - - dma_device_address[dmanr] = a; -} - -/* - * NOTE 2: "count" represents _bytes_. - */ -static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count) -{ - volatile unsigned short *dmawp; - -#ifdef DMA_DEBUG - printk("set_dma_count(dmanr=%d,count=%d)\n", dmanr, count); -#endif - - dmawp = (unsigned short *) dma_base_addr[dmanr]; - dmawp[MCFDMA_BCR] = (unsigned short)count; -} - -/* - * Get DMA residue count. After a DMA transfer, this - * should return zero. Reading this while a DMA transfer is - * still in progress will return unpredictable results. - * Otherwise, it returns the number of _bytes_ left to transfer. - */ -static __inline__ int get_dma_residue(unsigned int dmanr) -{ - volatile unsigned short *dmawp; - unsigned short count; - -#ifdef DMA_DEBUG - printk("get_dma_residue(dmanr=%d)\n", dmanr); -#endif - - dmawp = (unsigned short *) dma_base_addr[dmanr]; - count = dmawp[MCFDMA_BCR]; - return((int) count); -} -#else /* CONFIG_M5272 is defined */ - -/* - * The MCF5272 DMA controller is very different than the controller defined above - * in terms of register mapping. For instance, with the exception of the 16-bit - * interrupt register (IRQ#85, for reference), all of the registers are 32-bit. - * - * The big difference, however, is the lack of device-requested DMA. All modes - * are dual address transfer, and there is no 'device' setup or direction bit. - * You can DMA between a device and memory, between memory and memory, or even between - * two devices directly, with any combination of incrementing and non-incrementing - * addresses you choose. This puts a crimp in distinguishing between the 'device - * address' set up by set_dma_device_addr. - * - * Therefore, there are two options. One is to use set_dma_addr and set_dma_device_addr, - * which will act exactly as above in -- it will look to see if the source is set to - * autoincrement, and if so it will make the source use the set_dma_addr value and the - * destination the set_dma_device_addr value. Otherwise the source will be set to the - * set_dma_device_addr value and the destination will get the set_dma_addr value. - * - * The other is to use the provided set_dma_src_addr and set_dma_dest_addr functions - * and make it explicit. Depending on what you're doing, one of these two should work - * for you, but don't mix them in the same transfer setup. - */ - -/* enable/disable a specific DMA channel */ -static __inline__ void enable_dma(unsigned int dmanr) -{ - volatile unsigned int *dmalp; - -#ifdef DMA_DEBUG - printk("enable_dma(dmanr=%d)\n", dmanr); -#endif - - dmalp = (unsigned int *) dma_base_addr[dmanr]; - dmalp[MCFDMA_DMR] |= MCFDMA_DMR_EN; -} - -static __inline__ void disable_dma(unsigned int dmanr) -{ - volatile unsigned int *dmalp; - -#ifdef DMA_DEBUG - printk("disable_dma(dmanr=%d)\n", dmanr); -#endif - - dmalp = (unsigned int *) dma_base_addr[dmanr]; - - /* Turn off external requests, and stop any DMA in progress */ - dmalp[MCFDMA_DMR] &= ~MCFDMA_DMR_EN; - dmalp[MCFDMA_DMR] |= MCFDMA_DMR_RESET; -} - -/* - * Clear the 'DMA Pointer Flip Flop'. - * Write 0 for LSB/MSB, 1 for MSB/LSB access. - * Use this once to initialize the FF to a known state. - * After that, keep track of it. :-) - * --- In order to do that, the DMA routines below should --- - * --- only be used while interrupts are disabled! --- - * - * This is a NOP for ColdFire. Provide a stub for compatibility. - */ -static __inline__ void clear_dma_ff(unsigned int dmanr) -{ -} - -/* set mode (above) for a specific DMA channel */ -static __inline__ void set_dma_mode(unsigned int dmanr, char mode) -{ - - volatile unsigned int *dmalp; - volatile unsigned short *dmawp; - -#ifdef DMA_DEBUG - printk("set_dma_mode(dmanr=%d,mode=%d)\n", dmanr, mode); -#endif - dmalp = (unsigned int *) dma_base_addr[dmanr]; - dmawp = (unsigned short *) dma_base_addr[dmanr]; - - /* Clear config errors */ - dmalp[MCFDMA_DMR] |= MCFDMA_DMR_RESET; - - /* Set command register */ - dmalp[MCFDMA_DMR] = - MCFDMA_DMR_RQM_DUAL | /* Mandatory Request Mode setting */ - MCFDMA_DMR_DSTT_SD | /* Set up addressing types; set to supervisor-data. */ - MCFDMA_DMR_SRCT_SD | /* Set up addressing types; set to supervisor-data. */ - /* source static-address-mode */ - ((mode & DMA_MODE_SRC_SA_BIT) ? MCFDMA_DMR_SRCM_SA : MCFDMA_DMR_SRCM_IA) | - /* dest static-address-mode */ - ((mode & DMA_MODE_DES_SA_BIT) ? MCFDMA_DMR_DSTM_SA : MCFDMA_DMR_DSTM_IA) | - /* burst, 32 bit, 16 bit or 8 bit transfers are separately configurable on the MCF5272 */ - (((mode & DMA_MODE_SSIZE_MASK) >> DMA_MODE_SSIZE_OFF) << MCFDMA_DMR_DSTS_OFF) | - (((mode & DMA_MODE_SSIZE_MASK) >> DMA_MODE_SSIZE_OFF) << MCFDMA_DMR_SRCS_OFF); - - dmawp[MCFDMA_DIR] |= MCFDMA_DIR_ASCEN; /* Enable completion interrupts */ - -#ifdef DEBUG_DMA - printk("%s(%d): dmanr=%d DMR[%x]=%x DIR[%x]=%x\n", __FILE__, __LINE__, - dmanr, (int) &dmalp[MCFDMA_DMR], dmalp[MCFDMA_DMR], - (int) &dmawp[MCFDMA_DIR], dmawp[MCFDMA_DIR]); -#endif -} - -/* Set transfer address for specific DMA channel */ -static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a) -{ - volatile unsigned int *dmalp; - -#ifdef DMA_DEBUG - printk("set_dma_addr(dmanr=%d,a=%x)\n", dmanr, a); -#endif - - dmalp = (unsigned int *) dma_base_addr[dmanr]; - - /* Determine which address registers are used for memory/device accesses */ - if (dmalp[MCFDMA_DMR] & MCFDMA_DMR_SRCM) { - /* Source incrementing, must be memory */ - dmalp[MCFDMA_DSAR] = a; - /* Set dest address, must be device */ - dmalp[MCFDMA_DDAR] = dma_device_address[dmanr]; - } else { - /* Destination incrementing, must be memory */ - dmalp[MCFDMA_DDAR] = a; - /* Set source address, must be device */ - dmalp[MCFDMA_DSAR] = dma_device_address[dmanr]; - } - -#ifdef DEBUG_DMA - printk("%s(%d): dmanr=%d DMR[%x]=%x SAR[%x]=%08x DAR[%x]=%08x\n", - __FILE__, __LINE__, dmanr, (int) &dmalp[MCFDMA_DMR], dmalp[MCFDMA_DMR], - (int) &dmalp[MCFDMA_DSAR], dmalp[MCFDMA_DSAR], - (int) &dmalp[MCFDMA_DDAR], dmalp[MCFDMA_DDAR]); -#endif -} - -/* - * Specific for Coldfire - sets device address. - * Should be called after the mode set call, and before set DMA address. - */ -static __inline__ void set_dma_device_addr(unsigned int dmanr, unsigned int a) -{ -#ifdef DMA_DEBUG - printk("set_dma_device_addr(dmanr=%d,a=%x)\n", dmanr, a); -#endif - - dma_device_address[dmanr] = a; -} - -/* - * NOTE 2: "count" represents _bytes_. - * - * NOTE 3: While a 32-bit register, "count" is only a maximum 24-bit value. - */ -static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count) -{ - volatile unsigned int *dmalp; - -#ifdef DMA_DEBUG - printk("set_dma_count(dmanr=%d,count=%d)\n", dmanr, count); -#endif - - dmalp = (unsigned int *) dma_base_addr[dmanr]; - dmalp[MCFDMA_DBCR] = count; -} - -/* - * Get DMA residue count. After a DMA transfer, this - * should return zero. Reading this while a DMA transfer is - * still in progress will return unpredictable results. - * Otherwise, it returns the number of _bytes_ left to transfer. - */ -static __inline__ int get_dma_residue(unsigned int dmanr) -{ - volatile unsigned int *dmalp; - unsigned int count; - -#ifdef DMA_DEBUG - printk("get_dma_residue(dmanr=%d)\n", dmanr); -#endif - - dmalp = (unsigned int *) dma_base_addr[dmanr]; - count = dmalp[MCFDMA_DBCR]; - return(count); -} - -#endif /* !defined(CONFIG_M5272) */ -#endif /* CONFIG_COLDFIRE */ - /* it's useless on the m68k, but unfortunately needed by the new bootmem allocator (but this should do it for this) */ #define MAX_DMA_ADDRESS PAGE_OFFSET diff --git a/arch/m68k/mm/motorola.c b/arch/m68k/mm/motorola.c index ecbe948f4c1a..df7f797c908a 100644 --- a/arch/m68k/mm/motorola.c +++ b/arch/m68k/mm/motorola.c @@ -27,7 +27,6 @@ #include <asm/pgalloc.h> #include <asm/machdep.h> #include <asm/io.h> -#include <asm/dma.h> #ifdef CONFIG_ATARI #include <asm/atari_stram.h> #endif diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index af6c3c329076..d6144978e32d 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -508,7 +508,7 @@ config MMC_OMAP_HS config MMC_WBSD tristate "Winbond W83L51xD SD/MMC Card Interface support" - depends on ISA_DMA_API && !M68K + depends on ISA_DMA_API help This selects the Winbond(R) W83L51xD Secure digital and Multimedia card Interface. diff --git a/sound/core/Makefile b/sound/core/Makefile index 350d704ced98..2762f03d9b7b 100644 --- a/sound/core/Makefile +++ b/sound/core/Makefile @@ -9,9 +9,7 @@ ifneq ($(CONFIG_SND_PROC_FS),) snd-y += info.o snd-$(CONFIG_SND_OSSEMUL) += info_oss.o endif -ifneq ($(CONFIG_M68K),y) snd-$(CONFIG_ISA_DMA_API) += isadma.o -endif snd-$(CONFIG_SND_OSSEMUL) += sound_oss.o snd-$(CONFIG_SND_VMASTER) += vmaster.o snd-$(CONFIG_SND_JACK) += ctljack.o jack.o diff --git a/sound/isa/Kconfig b/sound/isa/Kconfig index 570b88e0b201..6ffa48dd5983 100644 --- a/sound/isa/Kconfig +++ b/sound/isa/Kconfig @@ -22,7 +22,7 @@ config SND_SB16_DSP menuconfig SND_ISA bool "ISA sound devices" depends on ISA || COMPILE_TEST - depends on ISA_DMA_API && !M68K + depends on ISA_DMA_API default y help Support for sound devices connected via the ISA bus. -- 2.29.2

1 0

[PATCH] ALSA: usb-audio: add mapping for MSI MAG X570S Torpedo MAX.
by Maurizio Avogadro 19 Apr '22

19 Apr '22

The USB audio device 0db0:419c based on the Realtek ALC4080 chipset exposes all playback volume controls as "PCM". This makes distinguishing the individual functions hard: the mapping already adopted for device 0db0:419c fixes the issue, apply it. Signed-off-by: Maurizio Avogadro <mavoga(a)gmail.com> --- sound/usb/mixer_maps.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/sound/usb/mixer_maps.c b/sound/usb/mixer_maps.c index 64f5544d0a0a..7ef7a8abcc2b 100644 --- a/sound/usb/mixer_maps.c +++ b/sound/usb/mixer_maps.c @@ -599,6 +599,10 @@ static const struct usbmix_ctl_map usbmix_ctl_maps[] = { .id = USB_ID(0x0db0, 0x419c), .map = msi_mpg_x570s_carbon_max_wifi_alc4080_map, }, + { /* MSI MAG X570S Torpedo Max */ + .id = USB_ID(0x0db0, 0xa073), + .map = msi_mpg_x570s_carbon_max_wifi_alc4080_map, + }, { /* MSI TRX40 */ .id = USB_ID(0x0db0, 0x543d), .map = trx40_mobo_map, -- 2.35.1

2 2

[PATCH v3] sound/oss/dmasound: fix build when drivers are mixed =y/=m
by Randy Dunlap 15 Apr '22

15 Apr '22

When CONFIG_DMASOUND_ATARI=m and CONFIG_DMASOUND_Q40=y (or vice versa), dmasound_core.o can be built without dmasound_deinit() being defined, causing a build error: ERROR: modpost: "dmasound_deinit" [sound/oss/dmasound/dmasound_atari.ko] undefined! Modify dmasound_core.c and dmasound.h so that dmasound_deinit() is always available. The mixed modes (=y/=m) also mean that several variables and structs have to be declared in all cases. Suggested-by: Arnd Bergmann <arnd(a)arndb.de> Suggested-by: Geert Uytterhoeven <geert(a)linux-m68k.org> Signed-off-by: Randy Dunlap <rdunlap(a)infradead.org> Reported-by: kernel test robot <lkp(a)intel.com> Link: lore.kernel.org/r/202204032138.EFT9qGEd-lkp@intel.com Cc: Geert Uytterhoeven <geert(a)linux-m68k.org> Cc: Jaroslav Kysela <perex(a)perex.cz> Cc: Takashi Iwai <tiwai(a)suse.com> Cc: alsa-devel(a)alsa-project.org --- v3: Remove use of #ifdef MODULE/#endif since the conditional data & code need to be there for some of the cases. (Geert) v2: make dmasound_deinit() defined and available in all configs (Arnd) @Geert: any way to test this? #Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") sound/oss/dmasound/dmasound.h | 6 ------ sound/oss/dmasound/dmasound_core.c | 24 +----------------------- 2 files changed, 1 insertion(+), 29 deletions(-) --- a/sound/oss/dmasound/dmasound_core.c +++ b/sound/oss/dmasound/dmasound_core.c @@ -206,12 +206,10 @@ module_param(writeBufSize, int, 0); MODULE_LICENSE("GPL"); -#ifdef MODULE static int sq_unit = -1; static int mixer_unit = -1; static int state_unit = -1; static int irq_installed; -#endif /* MODULE */ /* control over who can modify resources shared between play/record */ static fmode_t shared_resource_owner; @@ -391,9 +389,6 @@ static const struct file_operations mixe static void mixer_init(void) { -#ifndef MODULE - int mixer_unit; -#endif mixer_unit = register_sound_mixer(&mixer_fops, -1); if (mixer_unit < 0) return; @@ -1171,9 +1166,6 @@ static const struct file_operations sq_f static int sq_init(void) { const struct file_operations *fops = &sq_fops; -#ifndef MODULE - int sq_unit; -#endif sq_unit = register_sound_dsp(fops, -1); if (sq_unit < 0) { @@ -1366,9 +1358,6 @@ static const struct file_operations stat static int state_init(void) { -#ifndef MODULE - int state_unit; -#endif state_unit = register_sound_special(&state_fops, SND_DEV_STATUS); if (state_unit < 0) return state_unit ; @@ -1386,10 +1375,9 @@ static int state_init(void) int dmasound_init(void) { int res ; -#ifdef MODULE + if (irq_installed) return -EBUSY; -#endif /* Set up sound queue, /dev/audio and /dev/dsp. */ @@ -1408,9 +1396,7 @@ int dmasound_init(void) printk(KERN_ERR "DMA sound driver: Interrupt initialization failed\n"); return -ENODEV; } -#ifdef MODULE irq_installed = 1; -#endif printk(KERN_INFO "%s DMA sound driver rev %03d installed\n", dmasound.mach.name, (DMASOUND_CORE_REVISION<<4) + @@ -1424,8 +1410,6 @@ int dmasound_init(void) return 0; } -#ifdef MODULE - void dmasound_deinit(void) { if (irq_installed) { @@ -1444,8 +1428,6 @@ void dmasound_deinit(void) unregister_sound_dsp(sq_unit); } -#else /* !MODULE */ - static int dmasound_setup(char *str) { int ints[6], size; @@ -1489,8 +1471,6 @@ static int dmasound_setup(char *str) __setup("dmasound=", dmasound_setup); -#endif /* !MODULE */ - /* * Conversion tables */ @@ -1577,9 +1557,7 @@ char dmasound_alaw2dma8[] = { EXPORT_SYMBOL(dmasound); EXPORT_SYMBOL(dmasound_init); -#ifdef MODULE EXPORT_SYMBOL(dmasound_deinit); -#endif EXPORT_SYMBOL(dmasound_write_sq); EXPORT_SYMBOL(dmasound_catchRadius); #ifdef HAS_8BIT_TABLES --- a/sound/oss/dmasound/dmasound.h +++ b/sound/oss/dmasound/dmasound.h @@ -88,11 +88,7 @@ static inline int ioctl_return(int __use */ extern int dmasound_init(void); -#ifdef MODULE extern void dmasound_deinit(void); -#else -#define dmasound_deinit() do { } while (0) -#endif /* description of the set-up applies to either hard or soft settings */ @@ -114,9 +110,7 @@ typedef struct { void *(*dma_alloc)(unsigned int, gfp_t); void (*dma_free)(void *, unsigned int); int (*irqinit)(void); -#ifdef MODULE void (*irqcleanup)(void); -#endif void (*init)(void); void (*silence)(void); int (*setFormat)(int);

3 3

Re: [PATCH v2] ALSA: hda: handle UAF at probe error
by Lucas De Marchi 15 Apr '22

15 Apr '22

On Thu, Apr 14, 2022 at 08:24:37PM +0200, Nirmoy Das wrote: >Call snd_card_free_on_error() on probe error instead of >calling snd_card_free() which should handle devres call orders. > >Issues: https://gitlab.freedesktop.org/drm/intel/-/issues/5701 >Fixes: e8ad415b7a55 ("ALSA: core: Add managed card creation") >Signed-off-by: Nirmoy Das <nirmoy.das(a)intel.com> This failure in i915 CI seems suspicious since is around module removal. https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_102714v1/fi-tgl-1115g4/i… And it seems it didn't fix the issue in dg2: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_102714v1/bat-dg2-8/igt@g… Lucas De Marchi >--- > sound/pci/hda/hda_intel.c | 7 ++++--- > 1 file changed, 4 insertions(+), 3 deletions(-) > >diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c >index 82a45f2b31c4..eb4228c9e37f 100644 >--- a/sound/pci/hda/hda_intel.c >+++ b/sound/pci/hda/hda_intel.c >@@ -1730,7 +1730,9 @@ static void azx_check_snoop_available(struct azx *chip) > static void azx_probe_work(struct work_struct *work) > { > struct hda_intel *hda = container_of(work, struct hda_intel, probe_work.work); >- azx_probe_continue(&hda->chip); >+ struct azx *chip = &hda->chip; >+ >+ snd_card_free_on_error(&chip->pci->dev, azx_probe_continue(chip)); > } > > static int default_bdl_pos_adj(struct azx *chip) >@@ -2028,7 +2030,7 @@ static void azx_firmware_cb(const struct firmware *fw, void *context) > dev_err(card->dev, "Cannot load firmware, continue without patching\n"); > if (!chip->disabled) { > /* continue probing */ >- azx_probe_continue(chip); >+ snd_card_free_on_error(&chip->pci->dev, azx_probe_continue(chip)); > } > } > #endif >@@ -2338,7 +2340,6 @@ static int azx_probe_continue(struct azx *chip) > out_free: > if (err < 0) { > pci_set_drvdata(pci, NULL); >- snd_card_free(chip->card); > return err; > } > >-- >2.35.1 >

2 1

Re: [PATCH v2] ALSA: hda: handle UAF at probe error
by Takashi Iwai 15 Apr '22

15 Apr '22

On Thu, 14 Apr 2022 20:24:37 +0200, Nirmoy Das wrote: > > Call snd_card_free_on_error() on probe error instead of > calling snd_card_free() which should handle devres call orders. This won't change any practical behavior, because HD-audio driver doesn't use snd_devm_card_new(). snd_card_free() still gets called explicitly in the relevant code paths. > Issues: https://gitlab.freedesktop.org/drm/intel/-/issues/5701 So it must be a different cause for this problem... thanks, Takashi

2 1

[PATCH] ALSA: hda/hdmi: add HDMI codec VID for Raptorlake-P
by Kai Vehmanen 15 Apr '22

15 Apr '22

Add HDMI codec VID for Intel Raptorlake-P platform. Signed-off-by: Kai Vehmanen <kai.vehmanen(a)linux.intel.com> --- sound/pci/hda/patch_hdmi.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/pci/hda/patch_hdmi.c b/sound/pci/hda/patch_hdmi.c index 3e086eebf88d..9f9784e93db2 100644 --- a/sound/pci/hda/patch_hdmi.c +++ b/sound/pci/hda/patch_hdmi.c @@ -4551,6 +4551,7 @@ HDA_CODEC_ENTRY(0x80862819, "DG2 HDMI", patch_i915_adlp_hdmi), HDA_CODEC_ENTRY(0x8086281a, "Jasperlake HDMI", patch_i915_icl_hdmi), HDA_CODEC_ENTRY(0x8086281b, "Elkhartlake HDMI", patch_i915_icl_hdmi), HDA_CODEC_ENTRY(0x8086281c, "Alderlake-P HDMI", patch_i915_adlp_hdmi), +HDA_CODEC_ENTRY(0x8086281f, "Raptorlake-P HDMI", patch_i915_adlp_hdmi), HDA_CODEC_ENTRY(0x80862880, "CedarTrail HDMI", patch_generic_hdmi), HDA_CODEC_ENTRY(0x80862882, "Valleyview2 HDMI", patch_i915_byt_hdmi), HDA_CODEC_ENTRY(0x80862883, "Braswell HDMI", patch_i915_byt_hdmi), base-commit: 4516d04608b40d9ad150df6c2faef4a12d038ff6 -- 2.35.1

2 1

[PATCH] ALSA: hda/hdmi: fix warning about PCM count when used with SOF
by Kai Vehmanen 15 Apr '22

15 Apr '22

With commit 13046370c4d1 ("ALSA: hda/hdmi: let new platforms assign the pcm slot dynamically"), old behaviour to consider the HDA pin number, when choosing PCM to assign, was dropped. Build on this change and limit the number of PCMs created to number of converters (= maximum number of concurrent display/receivers) when "mst_no_extra_pcms" and "dyn_pcm_no_legacy" quirks are both set. Fix the check in hdmi_find_pcm_slot() to ensure only spec->pcm_used entries are considered in the search. Elsewhere in the driver spec->pcm_used is already checked properly. Doing this avoids following warning at SOF driver probe for multiple machine drivers: [ 112.425297] sof_sdw sof_sdw: hda_dsp_hdmi_build_controls: no PCM in topology for HDMI converter 4 [ 112.425298] sof_sdw sof_sdw: hda_dsp_hdmi_build_controls: no PCM in topology for HDMI converter 5 [ 112.425299] sof_sdw sof_sdw: hda_dsp_hdmi_build_controls: no PCM in topology for HDMI converter 6 BugLink: https://github.com/thesofproject/linux/issues/2573 Signed-off-by: Kai Vehmanen <kai.vehmanen(a)linux.intel.com> --- sound/pci/hda/patch_hdmi.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/sound/pci/hda/patch_hdmi.c b/sound/pci/hda/patch_hdmi.c index 3e086eebf88d..f9d67058d69d 100644 --- a/sound/pci/hda/patch_hdmi.c +++ b/sound/pci/hda/patch_hdmi.c @@ -1395,7 +1395,7 @@ static int hdmi_find_pcm_slot(struct hdmi_spec *spec, last_try: /* the last try; check the empty slots in pins */ - for (i = 0; i < spec->num_nids; i++) { + for (i = 0; i < spec->pcm_used; i++) { if (!test_bit(i, &spec->pcm_bitmap)) return i; } @@ -2325,7 +2325,9 @@ static int generic_hdmi_build_pcms(struct hda_codec *codec) * dev_num is the device entry number in a pin */ - if (codec->mst_no_extra_pcms) + if (spec->dyn_pcm_no_legacy && codec->mst_no_extra_pcms) + pcm_num = spec->num_cvts; + else if (codec->mst_no_extra_pcms) pcm_num = spec->num_nids; else pcm_num = spec->num_nids + spec->dev_num - 1; base-commit: 4516d04608b40d9ad150df6c2faef4a12d038ff6 -- 2.35.1

2 1