November 2021 - Alsa-devel - mailman.alsa-project.org

only have sound after mute and unmute and set volume in alsamixer
by GitHub issues - opened 01 Nov '21

01 Nov '21

alsa-project/alsa-ucm-conf issue #113 was opened from amazingfate: I have a x86 thinclient with debian bullseye installed. It has no sound in my headphone after boot, but I open alsamixer and then: 1, press M to mute the master 2, press M again to unmute the master 3, change the master volume from 100 to 99 After the above three steps I can hear the sound from my headphone. Here is the alsainfo before and after the three steps: [alsa-info_nosound.txt](https://github.com/alsa-project/alsa-ucm-conf/files/… [alsa-info_sound.txt](https://github.com/alsa-project/alsa-ucm-conf/files/74… I can see the difference in "Amp-Out vals". Issue URL : https://github.com/alsa-project/alsa-ucm-conf/issues/113 Repository URL: https://github.com/alsa-project/alsa-ucm-conf

1 0

[PATCH v2 1/2] dt-bindings: sound: tlv320adc3xxx: New codec driver
by Ricard Wanderlof 01 Nov '21

01 Nov '21

DT bindings for tlv320adc3xxx driver, currently supporting Texas Instruments TLV320ADC3001 and TLV320ADC3101 audio ADCs. Signed-off-by: Ricard Wanderlof <ricardw(a)axis.com> --- .../bindings/sound/ti,tlv320adc3xxx.yaml | 137 ++++++++++++++++++ include/dt-bindings/sound/tlv320adc3xxx.h | 28 ++++ 2 files changed, 165 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/ti,tlv320adc3xxx.yaml create mode 100644 include/dt-bindings/sound/tlv320adc3xxx.h diff --git a/Documentation/devicetree/bindings/sound/ti,tlv320adc3xxx.yaml b/Documentation/devicetree/bindings/sound/ti,tlv320adc3xxx.yaml new file mode 100644 index 000000000000..c4fed6335230 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ti,tlv320adc3xxx.yaml @@ -0,0 +1,137 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/ti,tlv320adc3xxx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments TLV320ADC3001/TLV320ADC3101 Stereo ADC + +maintainers: + - Ricard Wanderlof <ricardw(a)axis.com> + +description: | + Texas Instruments TLV320ADC3001 and TLV320ADC3101 Stereo ADC + https://www.ti.com/product/TLV320ADC3001 + https://www.ti.com/product/TLV320ADC3101 + +properties: + compatible: + enum: + - ti,tlv320adc3001 + - ti,tlv320adc3101 + + reg: + maxItems: 1 + description: I2C address + + '#sound-dai-cells': + const: 0 + + '#gpio-cells': + const: 2 + + gpio-controller: true + + reset-gpios: + maxItems: 1 + description: GPIO pin used for codec reset (RESET pin) + + clocks: + maxItems: 1 + description: Master clock (MCLK) + + ti,dmdin-gpio1: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # ADC3XXX_GPIO_DISABLED - I/O buffers powered down and not used + - 1 # ADC3XXX_GPIO_INPUT - Various non-GPIO input functions + - 2 # ADC3XXX_GPIO_GPI - General purpose input + - 3 # ADC3XXX_GPIO_GPO - General purpose output + - 4 # ADC3XXX_GPIO_CLKOUT - Clock source set in CLKOUT_MUX reg + - 5 # ADC3XXX_GPIO_INT1 - INT1 output + - 6 # ADC3XXX_GPIO_SECONDARY_BCLK - Codec interface secondary BCLK + - 7 # ADC3XXX_GPIO_SECONDARY_WCLK - Codec interface secondary WCLK + default: 0 + description: | + Configuration for DMDIN/GPIO1 pin. + + When ADC3XXX_GPIO_GPO is configured, this causes corresponding the + ALSA control "GPIOx Output" to appear, as a switch control. + + ti,dmclk-gpio2: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # ADC3XXX_GPIO_DISABLED - I/O buffers powered down and not used + - 1 # ADC3XXX_GPIO_INPUT - Various non-GPIO input functions + - 2 # ADC3XXX_GPIO_GPI - General purpose input + - 3 # ADC3XXX_GPIO_GPO - General purpose output + - 4 # ADC3XXX_GPIO_CLKOUT - Clock source set in CLKOUT_MUX reg + - 5 # ADC3XXX_GPIO_INT1 - INT1 output + - 6 # ADC3XXX_GPIO_SECONDARY_BCLK - Codec interface secondary BCLK + - 7 # ADC3XXX_GPIO_SECONDARY_WCLK - Codec interface secondary WCLK + default: 0 + description: | + Configuration for DMCLK/GPIO2 pin. + + When ADC3XXX_GPIO_GPO is configured, this causes corresponding the + ALSA control "GPIOx Output" to appear, as a switch control. + + Note that there is currently no support for reading the GPIO pins as + inputs. + + ti,micbias1-vg: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # ADC3XXX_MICBIAS_OFF - Mic bias is powered down + - 1 # ADC3XXX_MICBIAS_2_0V - Mic bias is set to 2.0V + - 2 # ADC3XXX_MICBIAS_2_5V - Mic bias is set to 2.5V + - 3 # ADC3XXX_MICBIAS_AVDD - Mic bias is same as AVDD supply + default: 0 + description: | + Mic bias voltage output on MICBIAS1 pin + + ti,micbias2-vg: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 # ADC3XXX_MICBIAS_OFF - Mic bias is powered down + - 1 # ADC3XXX_MICBIAS_2_0V - Mic bias is set to 2.0V + - 2 # ADC3XXX_MICBIAS_2_5V - Mic bias is set to 2.5V + - 3 # ADC3XXX_MICBIAS_AVDD - Mic bias is same as AVDD supply + default: 0 + description: | + Mic bias voltage output on MICBIAS2 pin + +required: + - compatible + - reg + - clocks + +additionalProperties: false + +examples: + - | + + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/sound/tlv320adc3xxx.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + tlv320adc3101: tlv320adc3101@18 { + compatible = "ti,tlv320adc3101"; + reg = <0x18>; + reset-gpios = <&gpio_pc 3 GPIO_ACTIVE_LOW>; + clocks = <&audio_mclk>; + gpio-controller; + #gpio-cells = <2>; + ti,dmdin-gpio1 = <ADC3XXX_GPIO_GPO>; + ti,micbias1-vg = <ADC3XXX_MICBIAS_AVDD>; + }; + }; + + audio_mclk: clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24576000>; + }; +... diff --git a/include/dt-bindings/sound/tlv320adc3xxx.h b/include/dt-bindings/sound/tlv320adc3xxx.h new file mode 100644 index 000000000000..59ed510e6cf1 --- /dev/null +++ b/include/dt-bindings/sound/tlv320adc3xxx.h @@ -0,0 +1,28 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Devicetree bindings definitions for tlv320adc3xxx driver. + * + * Copyright (C) 2021 Axis Communications AB + */ +#ifndef __DT_TLV320ADC3XXX_H +#define __DT_TLV320ADC3XXX_H + +#define ADC3XXX_GPIO_DISABLED 0 /* I/O buffers powered down */ +#define ADC3XXX_GPIO_INPUT 1 /* Various non-GPIO inputs */ +#define ADC3XXX_GPIO_GPI 2 /* General purpose input */ +#define ADC3XXX_GPIO_GPO 3 /* General purpose output */ +#define ADC3XXX_GPIO_CLKOUT 4 /* Source set in reg. CLKOUT_MUX */ +#define ADC3XXX_GPIO_INT1 5 /* INT1 output */ +#define ADC3XXX_GPIO_INT2 6 /* INT2 output */ +/* value 7 is reserved */ +#define ADC3XXX_GPIO_SECONDARY_BCLK 8 /* Codec interface secondary BCLK */ +#define ADC3XXX_GPIO_SECONDARY_WCLK 9 /* Codec interface secondary WCLK */ +#define ADC3XXX_GPIO_ADC_MOD_CLK 10 /* Clock output for digital mics */ +/* values 11-15 reserved */ + +#define ADC3XXX_MICBIAS_OFF 0 /* Micbias pin powered off */ +#define ADC3XXX_MICBIAS_2_0V 1 /* Micbias pin set to 2.0V */ +#define ADC3XXX_MICBIAS_2_5V 2 /* Micbias pin set to 2.5V */ +#define ADC3XXX_MICBIAS_AVDD 3 /* Use AVDD voltage for micbias pin */ + +#endif /* __DT_TLV320ADC3XXX_H */ -- 2.20.1 -- Ricard Wolf Wanderlof ricardw(at)axis.com Axis Communications AB, Lund, Sweden www.axis.com Phone +46 46 272 2016 Fax +46 46 13 61 30

1 0

[PATCH v2 0/2] Codec driver for TLV320ADC3001 and 3101
by Ricard Wanderlof 01 Nov '21

01 Nov '21

This is a codec driver for the TLV320ADC3001 and TLV320ADC3101 2 channel audio ADC chips from Texas Instruments. Based on an old driver for these chips that I was referred to by Texas Instruments, but which apparently was never upstreamed, I've taken patches from various incarnations, ported them and augmented them with various new features in order to make a working driver. There is currently no support for the on-chip "miniDSP". Although the TLV320ADC3001 and TLV320ADC3101 have similarities with other TI codec chips for which there are existing drivers, upon closer inspection I decided the differences were too great to warrant attempting to modify an existing driver, especially without access to all supported chips and resources for testing them all. There are certainly things that could be improved, among others in the area of PLL register value calculations, but it has been tested on the Axis ARTPEC-8 platform and has been found to work satisfactorily at least with a TLV320ADC3101 operating as an I2S slave at 48 kHz with 32 bit bit depth, 1 or 2 channels, both with the on-chip PLL enabled and disabled. I have not tested this on a TLV320ADC3001 chip; in the original driver the only differences were related to the now-removed initialization code, so I've just retained the compatible strings for both chips. Limitations: - GPIO pins on chip can only be set up as outputs. - Using BCLK as an input to clock chain is supported by the hw but not by driver. Large portions of the driver have been reworked from v1 based on remarks from Mark. More specifically: - Remove an unneeded #ifdef and EXPORT_SYMBOL_GPL. - Add ADC3XXX_ prefix to all macro names to avoid namespace contention. - Clean up certain macro names with mixed lower case - upper case names. - Do away with the D0..D7 macros representing bit values. - Fix general formatting: spaces before and after {, }, replace multi spaces with tabs, maximum 2 blank lines anywhere, and other minor issues. - Page register does not need to be volatile. - Rather than use 0 / -6dB enum for input attenuator, use standard TLV. - The dither offset control contains reserved values so use VALUE_ENUM instead of straight ENUM. - Replace vector of SOC_ENUMs with individual variables. - Fix ALSA control names: - Use Volume at the end of all gain controls, and remove "Gain" where applicable. - Use "Switch" at the end of all switch controls, either adding it or changing "switch" into "Switch" as applicable. - Switches and Volumes related to capture should be set up as such, so add "Capture" to widget names where appropriate. This is mostly important for the PGA Capture and Switch widgets, not just for consistency, but also because amixer simple Switch controls expect different names (cap/nocap instead of on/off) for control values for capture. - Make widget names have capital first letters for all consitutent words. - When resuming, the registers will not have changed, so no need to call snd_soc_component_cache_sync(). - Move reset gpio init to I2C probe - Remove needless _priv at end of private struct name. - Make hex constants lower case - _CBM_CFM/_CBS_CFS -> _CBP_CFP/_CBC_CFC - Instead of using device specific ALSA controls to control the two GPIO pins, use GPIOLIB. GPIO pin functions still can be set up in the devicetree as the pins can be used for other functions which are not GPIO related. - Limitation: The GPIO pins can only be used as outputs, even though the hardware alternatively supports using them as inputs. - Handle GPIO configs in a vector rather than separately. - Use more appropriate module_i2c_driver instead of generic module_init/module_exit. - Remove useless initialization data. - As the ADC mute function had no control, add it. - Clean up GPIO initialization which was done both in the I2C probe and in the component probe. - Remove probe, remove, suspend and resume callbacks, which either do not do anything at all anymore, or uselessly just do set_bias_level. - The PLL should not be configured in the devicetree, so move the corresponding definitions to tlv320adc3xxx.h where they can be picked up by a machine driver if needed. - Default to PLL AUTO mode. - Use "reset-gpios" instead of too-generic "gpios" for dt property for configuring codec reset pin. - Use function for printing PLL mode rather than macro. - dev_info is too verbose for most of the printouts, change them to dev_dbg. - Add support for configuring micbias voltage in DT. - Remove ALSA control for mic bias. - Move PLL and NADC, MADC divisor enable to DAPM, including 10 ms post PLL start up delay via POST_PMU event. - ADC is powered on using DAPM, so needless to do it in set_bias_level, thus remove it. - Let DAPM handle BCLK divisor enable. With this, we can remove set_bias_level as it doesn't do anything anymore. - Fix incorrect argument order to a snd_soc_component_update_bits call. - Although the chip itself can operate using BCLK as the clock source, either directly to the divider chain or via the PLL, this is not yet supported in the driver, so require the clocks property for the MCLK for now. - Move PLL rate structure out of .h file where it does not belong. /Ricard Ricard Wanderlof (2): dt-bindings: sound: tlv320adc3xxx: New codec driver ASoC: codec: tlv320adc3xxx: New codec driver .../bindings/sound/ti,tlv320adc3xxx.yaml | 137 +++ include/dt-bindings/sound/tlv320adc3xxx.h | 28 + sound/soc/codecs/Kconfig | 7 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/tlv320adc3xxx.c | 1071 +++++++++++++++++ sound/soc/codecs/tlv320adc3xxx.h | 379 ++++++ 6 files changed, 1624 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/ti,tlv320adc3xxx.yaml create mode 100644 include/dt-bindings/sound/tlv320adc3xxx.h create mode 100644 sound/soc/codecs/tlv320adc3xxx.c create mode 100644 sound/soc/codecs/tlv320adc3xxx.h -- 2.20.1 -- Ricard Wolf Wanderlof ricardw(at)axis.com Axis Communications AB, Lund, Sweden www.axis.com Phone +46 46 272 2016 Fax +46 46 13 61 30

1 0

[PATCH] ALSA: usb-audio: Line6 HX-Stomp XL USB_ID
by Jason Ormes 01 Nov '21

01 Nov '21

Adding the Line6 HX-Stomp XL USB_ID as it needs this fixed frequency quirk as well. The device is basically just the HX-Stomp with some more buttons on the face. I've Done some recording with it after adding it, and it seems to function properly with this fix. The Midi features appear to be working as well. Signed-off-by: Jason Ormes <skryking(a)gmail.com> --- sound/usb/format.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/usb/format.c b/sound/usb/format.c index 50efccbffb8a..e8fc2c350a9f 100644 --- a/sound/usb/format.c +++ b/sound/usb/format.c @@ -414,6 +414,7 @@ static int line6_parse_audio_format_rates_quirk(struct snd_usb_audio *chip, case USB_ID(0x0e41, 0x4242): /* Line6 Helix Rack */ case USB_ID(0x0e41, 0x4244): /* Line6 Helix LT */ case USB_ID(0x0e41, 0x4246): /* Line6 HX-Stomp */ + case USB_ID(0x0e41, 0x4253): /* Line6 HX-Stomp XL*/ case USB_ID(0x0e41, 0x4247): /* Line6 Pod Go */ case USB_ID(0x0e41, 0x4248): /* Line6 Helix >= fw 2.82 */ case USB_ID(0x0e41, 0x4249): /* Line6 Helix Rack >= fw 2.82 */ -- 2.25.1

2 1

[PATCH] ALSA: usb-audio: Add registration quirk for JBL Quantum 400
by Alexander Tsoy 01 Nov '21

01 Nov '21

Add another device ID for JBL Quantum 400. It requires the same quirk as other JBL Quantum devices. Signed-off-by: Alexander Tsoy <alexander(a)tsoy.me> --- sound/usb/quirks.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/usb/quirks.c b/sound/usb/quirks.c index 8929d9abe8aa..1d418c3fc598 100644 --- a/sound/usb/quirks.c +++ b/sound/usb/quirks.c @@ -1749,6 +1749,7 @@ static const struct registration_quirk registration_quirks[] = { REG_QUIRK_ENTRY(0x0951, 0x16ea, 2), /* Kingston HyperX Cloud Flight S */ REG_QUIRK_ENTRY(0x0ecb, 0x1f46, 2), /* JBL Quantum 600 */ REG_QUIRK_ENTRY(0x0ecb, 0x1f47, 2), /* JBL Quantum 800 */ + REG_QUIRK_ENTRY(0x0ecb, 0x1f4c, 2), /* JBL Quantum 400 */ REG_QUIRK_ENTRY(0x0ecb, 0x2039, 2), /* JBL Quantum 400 */ REG_QUIRK_ENTRY(0x0ecb, 0x203c, 2), /* JBL Quantum 600 */ REG_QUIRK_ENTRY(0x0ecb, 0x203e, 2), /* JBL Quantum 800 */ -- 2.32.0

2 1