May 2010 - Alsa-devel - mailman.alsa-project.org

[alsa-devel] [PATCH 0/7] ASoC: TWL4030: put the codec to off when not active
by Peter Ujfalusi 26 May '10

26 May '10

Hello, The following series at the end will let the twl4030 codec to use BIAS_OFF instead of BIAS_STANDBY. The difference in power consumption is about 0.5mA. To achieve this: - The regcache has been reseted to codec default - The codec initialization has been optimized, it is no longer writes all 73 registers at startup, but only modifies few selected one. - The power related code has been cleaned up, and optimized - Support added for machine drivers to select the offset cancellation path - debug support for checking the codec default registers (machine drivers can ask for checking, but shall be disabled in production). I guess that's it. The driver has been tested on a custom board with twl5031. It passed all of our internal test cases covering much of the codec features. --- Peter Ujfalusi (7): ASoC: TWL4030: Revisit codec defaults ASoC: TWL4030: Remove wrapper for power down ASoC: TWL4030: Make offset cancellation path configurable ASoC: TWL4030: Optimize the power up sequence ASoC: TWL4030: Helper to check chip default registers ASoC: TWL4030: Correct the ARXR2_APGA_CTL chip default ASoC: TWL4030: Use BIAS_OFF instead of BIAS_STANDBY, when not in use sound/soc/codecs/twl4030.c | 286 ++++++++++++++++++++++++-------------------- sound/soc/codecs/twl4030.h | 2 + 2 files changed, 157 insertions(+), 131 deletions(-)

3 16

Re: [alsa-devel] [patch 4/5] orion/kirkwood: Add i2s support
by saeed bishara 26 May '10

26 May '10

On Wed, May 26, 2010 at 3:31 AM, Nicolas Pitre <nico(a)fluxnic.net> wrote: > On Tue, 25 May 2010, apatard(a)mandriva.com wrote: > >> This patch enables support for the i2s controller available on orion/kirkwood platforms >> >> Signed-off-by: Arnaud Patard <apatard(a)mandriva.com> > > The actual Orion processor family has no I2S/audio support. It would be > better if all the audio related stuff was renamed to "kirkwood" and > "KIRKWOOD_*" instead. This i2s was first included in orion90L (6183). saeed

1 0

Re: [alsa-devel] [patch 0/5] kirkwood openrd client audio support - v3
by Mark Brown 26 May '10

26 May '10

On Tue, May 25, 2010 at 09:10:54PM -0400, Nicolas Pitre wrote: > I don't mind if you wish to carry it through the ASOC tree. The bulk of > it is ASOC related anyway. However I think that "orion" names should be > "kirkwood" throughout instead, as pure Orion chips have no audio > interfaces. Can I add an ack from you for the patches with the name change, then?

1 0

[alsa-devel] [PATCH]alsa:patch_realtek.c iMac9,1 sound fixes.
by Justin P. Mattock 25 May '10

25 May '10

What seemed to be a simple little task of getting the microphone to work, ended up becoming a bigger task than I had set out. (oh-well, good learning experience). Anyways below you will find an updated patch to the iMac9,1 machine which fixes some issues that I found.(keep in mind this is still a work in progress). First issue: With the original patch, I've noticed by unmuting the mic (and even having it muted), there is a distorted("Noise") coming from the internal speakers, even when the headphones are plugged in. What my finding's revealed is: /* Mic (rear) pin: input vref at 80% */ {0x18, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_VREF80}, {0x18, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE}, _From the original patch. Looking at codec#0 0x18/0x1a is listed as: Node 0x18 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 Amp-In vals: [0x00 0x00] Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x00 0x00] Pincap 0x0000373c: IN OUT HP Detect Vref caps: HIZ 50 GRD 80 100 Pin Default 0x90100141: [Fixed] Speaker at Int N/A Conn = Unknown, Color = Unknown DefAssociation = 0x4, Sequence = 0x1 Misc = NO_PRESENCE Pin-ctls: 0x41: OUT VREF_50 Unsolicited: tag=00, enabled=0 Connection: 5 0x0c* 0x0d 0x0e 0x0f 0x26 seems this Node is listed as: [Fixed] Speaker while 0x15 Node 0x15 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 Amp-In vals: [0x00 0x00] Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80] Pincap 0x0000373c: IN OUT HP Detect Vref caps: HIZ 50 GRD 80 100 Pin Default 0x018b3020: [Jack] Line In at Ext Rear Conn = Comb, Color = Blue DefAssociation = 0x2, Sequence = 0x0 Pin-ctls: 0x01: VREF_50 Unsolicited: tag=00, enabled=0 Connection: 5 0x0c 0x0d* 0x0e 0x0f 0x26 is [Jack] Line In at Ext Rear. (looking at the other apple products as examples I came up with the fix below). Second issue: alc885_mbp_4ch_modes The original patch does a good job with the HP pin automute function, but from what I noticed is I would have to manually change the channel form 2 to 4 after plugging the headphones in. And not to mention having odd moments to where I was jamming out with the headphones on, then later realized I had sound blasting out of the speakers as well. My findings revealed that changing alc885_mbp_4ch_modes to alc885_mba21_ch_modes and setting - spec->autocfg.speaker_pins[0] = 0x15; + spec->autocfg.speaker_pins[0] = 0x18; gets the automute function when the headphones plugged in working flawlessly(and the no need to manually change the channel number afterwards). Third issue: alc885_imac91_mixer There probably doesnt need to be anything changed with this (esspecially if your one to like lots of sliders),but my findings revealed that mac osx only has a master on the top right, another switch on itunes, and then a slider for the mic. So the changes I did below try and mimic osx as much as possible (only thing I had an issue with is just having one mute switch on the master, instead of having two(still investigating)). fourth issue: alc882_capture_source I endeded up creating alc889A_imac91_capture_source() only because looking at alc882_capture_source I see that the mic is set to 0x1 while this works, I also noticed that adding 0x1 and 0x01 and testing that 0x1 somehow stops working, and 0x01 works(so I figured 0x01 was more of the alpha of the numbers(still need to figure out where that valuse is)). In any case the microphone does work with the original, and with the below patch, but both still record not as clean(lots of "Noise", which I would like to look into too). Note: using alsamixer -Va reveals the capture switches. Overall the original patch is good, the below patch does (hopefully)address some issues, if it's too much of a change I can go back, and just adjust the verb pins on the original and just call it that..(main thing over here is I don't have the "Noise" coming out of the speakers(and music sounds good)... cheers.. Signed-off-by: Justin P. Mattock <justinmattock(a)gmail.com> --- sound/pci/hda/patch_realtek.c | 84 +++++++++++++++++++--------------------- 1 files changed, 40 insertions(+), 44 deletions(-) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 886d8e4..d8adea3 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -6937,6 +6937,14 @@ static struct hda_input_mux alc889A_mb31_capture_source = { }, }; +static struct hda_input_mux alc889A_imac91_capture_source = { + .num_items = 2, + .items = { + { "Mic", 0x01 }, + { "Line", 0x2 }, /* Not sure! */ + }, +}; + /* * 2ch mode */ @@ -7398,15 +7406,8 @@ static struct snd_kcontrol_new alc885_macmini3_mixer[] = { }; static struct snd_kcontrol_new alc885_imac91_mixer[] = { - HDA_CODEC_VOLUME("Line-Out Playback Volume", 0x0c, 0x00, HDA_OUTPUT), - HDA_BIND_MUTE ("Line-Out Playback Switch", 0x0c, 0x02, HDA_INPUT), - HDA_CODEC_MUTE ("Speaker Playback Switch", 0x14, 0x00, HDA_OUTPUT), - HDA_CODEC_VOLUME("Speaker Playback Volume", 0x0d, 0x00, HDA_OUTPUT), - HDA_CODEC_VOLUME("Line Playback Volume", 0x0b, 0x02, HDA_INPUT), - HDA_CODEC_MUTE ("Line Playback Switch", 0x0b, 0x02, HDA_INPUT), - HDA_CODEC_VOLUME("Mic Playback Volume", 0x0b, 0x00, HDA_INPUT), - HDA_CODEC_MUTE ("Mic Playback Switch", 0x0b, 0x00, HDA_INPUT), - HDA_CODEC_VOLUME("Mic Boost", 0x18, 0x00, HDA_INPUT), + HDA_CODEC_VOLUME("Speaker Playback Volume", 0x0c, 0x00, HDA_OUTPUT), + HDA_BIND_MUTE("Speaker Playback Switch", 0x0c, 0x02, HDA_INPUT), { } /* end */ }; @@ -7907,61 +7908,56 @@ static struct hda_verb alc885_mbp3_init_verbs[] = { /* iMac 9,1 */ static struct hda_verb alc885_imac91_init_verbs[] = { - /* Line-Out mixer: unmute input/output amp left and right (volume = 0) */ - {0x0c, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO}, - {0x0c, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, - {0x0c, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)}, - /* Rear mixer */ - {0x0d, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO}, - {0x0d, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, - {0x0d, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)}, - /* HP Pin: output 0 (0x0c) */ + /* Internal Speaker Pin (0x0c) */ + {0x18, AC_VERB_SET_PIN_WIDGET_CONTROL, (PIN_OUT | AC_PINCTL_VREF_50) }, + {0x18, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE}, + {0x18, AC_VERB_SET_CONNECT_SEL, 0x00}, + {0x1a, AC_VERB_SET_PIN_WIDGET_CONTROL, (PIN_OUT | AC_PINCTL_VREF_50) }, + {0x1a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE}, + {0x1a, AC_VERB_SET_CONNECT_SEL, 0x00}, + /* HP Pin: Rear */ {0x14, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_HP}, {0x14, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE}, {0x14, AC_VERB_SET_CONNECT_SEL, 0x00}, - {0x14, AC_VERB_SET_UNSOLICITED_ENABLE, ALC880_HP_EVENT | AC_USRSP_EN}, - /* Internal Speakers: output 0 (0x0d) */ - {0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT}, + {0x14, AC_VERB_SET_UNSOLICITED_ENABLE, (ALC880_HP_EVENT | AC_USRSP_EN)}, + /* Line in Rear */ + {0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, AC_PINCTL_VREF_50}, {0x15, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE}, - {0x15, AC_VERB_SET_CONNECT_SEL, 0x00}, - /* Mic (rear) pin: input vref at 80% */ - {0x18, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_VREF80}, - {0x18, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE}, /* Front Mic pin: input vref at 80% */ {0x19, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_VREF80}, {0x19, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE}, - /* Line In pin: use output 1 when in LineOut mode */ - {0x1a, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN}, - {0x1a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE}, - {0x1a, AC_VERB_SET_CONNECT_SEL, 0x01}, - - /* FIXME: use matrix-type input source selection */ - /* Mixer elements: 0x18, 19, 1a, 1b, 1c, 1d, 14, 15, 16, 17, 0b */ - /* Input mixer1: unmute Mic, F-Mic, Line, CD inputs */ + /* Rear mixer */ + {0x0d, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO}, + {0x0d, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, + {0x0d, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)}, + /* Line-Out mixer: unmute input/output amp left and right (volume = 0) */ + {0x0c, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO}, + {0x0c, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, + {0x0c, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)}, + /* 0x24 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In */ {0x24, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, {0x24, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)}, {0x24, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)}, {0x24, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)}, - /* Input mixer2 */ + /* 0x23 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In */ {0x23, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, {0x23, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)}, {0x23, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)}, {0x23, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)}, - /* Input mixer3 */ + /* 0x22 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In */ {0x22, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, {0x22, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)}, {0x22, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)}, {0x22, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)}, - /* ADC1: mute amp left and right */ + /* 0x07 [Audio Input] wcaps 0x10011b: Stereo Amp-In */ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, {0x07, AC_VERB_SET_CONNECT_SEL, 0x00}, - /* ADC2: mute amp left and right */ + /* 0x08 [Audio Input] wcaps 0x10011b: Stereo Amp-In */ {0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, {0x08, AC_VERB_SET_CONNECT_SEL, 0x00}, - /* ADC3: mute amp left and right */ + /* 0x09 [Audio Input] wcaps 0x10011b: Stereo Amp-In */ {0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, {0x09, AC_VERB_SET_CONNECT_SEL, 0x00}, - { } }; @@ -8030,7 +8026,7 @@ static void alc885_imac91_setup(struct hda_codec *codec) struct alc_spec *spec = codec->spec; spec->autocfg.hp_pins[0] = 0x14; - spec->autocfg.speaker_pins[0] = 0x15; + spec->autocfg.speaker_pins[0] = 0x18; spec->autocfg.speaker_pins[1] = 0x1a; } @@ -9539,14 +9535,14 @@ static struct alc_config_preset alc882_presets[] = { .init_hook = alc885_imac24_init_hook, }, [ALC885_IMAC91] = { - .mixers = { alc885_imac91_mixer, alc882_chmode_mixer }, + .mixers = {alc885_imac91_mixer}, .init_verbs = { alc885_imac91_init_verbs, alc880_gpio1_init_verbs }, .num_dacs = ARRAY_SIZE(alc882_dac_nids), .dac_nids = alc882_dac_nids, - .channel_mode = alc885_mbp_4ch_modes, - .num_channel_mode = ARRAY_SIZE(alc885_mbp_4ch_modes), - .input_mux = &alc882_capture_source, + .channel_mode = alc885_mba21_ch_modes, + .num_channel_mode = ARRAY_SIZE(alc885_mba21_ch_modes), + .input_mux = &alc889A_imac91_capture_source, .dig_out_nid = ALC882_DIGOUT_NID, .dig_in_nid = ALC882_DIGIN_NID, .unsol_event = alc_automute_amp_unsol_event, -- 1.7.1.rc1.21.gf3bd6

2 2

[alsa-devel] [PATCH] ALSA: usb/caiaq: fix Traktor Kontrol X1 ABS_HAT2X axis
by Daniel Mack 25 May '10

25 May '10

Signed-off-by: Daniel Mack <daniel(a)caiaq.de> --- sound/usb/caiaq/input.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-) diff --git a/sound/usb/caiaq/input.c b/sound/usb/caiaq/input.c index 8bbfbfd..dcb6207 100644 --- a/sound/usb/caiaq/input.c +++ b/sound/usb/caiaq/input.c @@ -171,7 +171,7 @@ static void snd_caiaq_input_read_analog(struct snd_usb_caiaqdev *dev, input_report_abs(input_dev, ABS_HAT0Y, (buf[4] << 8) | buf[5]); input_report_abs(input_dev, ABS_HAT1X, (buf[12] << 8) | buf[13]); input_report_abs(input_dev, ABS_HAT1Y, (buf[2] << 8) | buf[3]); - input_report_abs(input_dev, ABS_HAT2X, (buf[15] << 8) | buf[15]); + input_report_abs(input_dev, ABS_HAT2X, (buf[14] << 8) | buf[15]); input_report_abs(input_dev, ABS_HAT2Y, (buf[0] << 8) | buf[1]); input_report_abs(input_dev, ABS_HAT3X, (buf[10] << 8) | buf[11]); input_report_abs(input_dev, ABS_HAT3Y, (buf[6] << 8) | buf[7]); -- 1.7.1

2 2

[alsa-devel] [PATCH] ALSA: hda: Fix model quirk for Dell M1730
by Daniel Chen 25 May '10

25 May '10

Hi, Attached please find a patch for sound-2.6 master HEAD that fixes capture out-of-the-box for Dell M1730. This patch is applicable to all 2.6.32, 2.6.33, and 2.6.34 stable trees. Best, -Dan

2 1

[alsa-devel] [PATCH] ALSA: hda: Use LPIB for Toshiba A100-259
by Daniel Chen 25 May '10

25 May '10

Hi, Attached please find a patch for sound-2.6 based on my previous patch (ALSA: hda: Use LPIB for Acer Aspire 5110) specifying the LPIB quirk for an additional SSID to make capture work correctly in an installed distribution. This patch is applicable to 2.6.32, 2.6.33, and 2.6.34 stable trees (some with fuzz). Best, -Dan

3 2

[alsa-devel] [PATCH] ALSA: hda: Use LPIB for Acer Aspire 5110
by Daniel Chen 25 May '10

25 May '10

Hi, Attached please find a patch against sound-2.6 master HEAD specifying the LPIB quirk for an additional SSID to make capture work correctly in an installed distribution. This patch is applicable to 2.6.32, 2.6.33, and 2.6.34 stable trees (some with fuzz). Best, -Dan

2 1

[alsa-devel] [PATCH] aw2-alsa.c: use pci_ids.h defines and fix checkpatch.pl noise
by H Hartley Sweeten 25 May '10

25 May '10

Use the VENDOR/DEVICE ids provided in pci_ids.h instead of creating local ids of the same values. Also, fix the following checkpatch.pl warnings: WARNING: Use #include <linux/io.h> instead of <asm/io.h> WARNING: unnecessary whitespace before a quoted newline Signed-off-by: H Hartley Sweeten <hsweeten(a)visionengravers.com> Cc: Jaroslav Kysela <perex(a)perex.cz> Cc: Takashi Iwai <tiwai(a)suse.de> --- diff --git a/sound/pci/aw2/aw2-alsa.c b/sound/pci/aw2/aw2-alsa.c index 67921f9..c150022 100644 --- a/sound/pci/aw2/aw2-alsa.c +++ b/sound/pci/aw2/aw2-alsa.c @@ -26,7 +26,7 @@ #include <linux/slab.h> #include <linux/interrupt.h> #include <linux/delay.h> -#include <asm/io.h> +#include <linux/io.h> #include <sound/core.h> #include <sound/initval.h> #include <sound/pcm.h> @@ -44,9 +44,6 @@ MODULE_LICENSE("GPL"); /********************************* * DEFINES ********************************/ -#define PCI_VENDOR_ID_SAA7146 0x1131 -#define PCI_DEVICE_ID_SAA7146 0x7146 - #define CTL_ROUTE_ANALOG 0 #define CTL_ROUTE_DIGITAL 1 @@ -165,7 +162,7 @@ module_param_array(enable, bool, NULL, 0444); MODULE_PARM_DESC(enable, "Enable Audiowerk2 soundcard."); static DEFINE_PCI_DEVICE_TABLE(snd_aw2_ids) = { - {PCI_VENDOR_ID_SAA7146, PCI_DEVICE_ID_SAA7146, 0, 0, + {PCI_VENDOR_ID_PHILIPS, PCI_DEVICE_ID_PHILIPS_SAA7146, 0, 0, 0, 0, 0}, {0} }; @@ -419,7 +416,7 @@ static int snd_aw2_pcm_playback_open(struct snd_pcm_substream *substream) { struct snd_pcm_runtime *runtime = substream->runtime; - snd_printdd(KERN_DEBUG "aw2: Playback_open \n"); + snd_printdd(KERN_DEBUG "aw2: Playback_open\n"); runtime->hw = snd_aw2_playback_hw; return 0; } @@ -435,7 +432,7 @@ static int snd_aw2_pcm_capture_open(struct snd_pcm_substream *substream) { struct snd_pcm_runtime *runtime = substream->runtime; - snd_printdd(KERN_DEBUG "aw2: Capture_open \n"); + snd_printdd(KERN_DEBUG "aw2: Capture_open\n"); runtime->hw = snd_aw2_capture_hw; return 0; }

2 1

Re: [alsa-devel] snd_intel_hda : broken microphone
by mutenmaster＠tiscali.it 25 May '10

25 May '10

ok you can find attached my codec0 output data. I hope this helps. if you or anyone else need any other piece of info, please ask. ---- Messaggio originale---- Apparently (I assume) this is not for all via sound chips so it's best to expalin what your setup is. The output from lspci does not tell the story on the codec at times. The best output is from /proc/asound/card0/codec#0 On Wed, 2010-05-19 at 11:33 +0200, mutenmaster(a)tiscali.it wrote: > hello people, > > i am really determined in letting you know, for the > third time, > that my front mic input does not work. i do not know if the > rear > one works, i suspect not, but it's not important, because > before > the following commit, the front mic input worked: > > $ sudo git bisect > bad > f5271101faf1655d862849f42518c2a88ef394fb > is the first bad commit > > commit f5271101faf1655d862849f42518c2a88ef394fb > > Author: Lydia Wang > <lydiawang(a)viatech.com.cn> > Date: Sat Oct 10 19:07: > 35 2009 +0800 > > > ALSA HDA VIA: Add VIA_CTL_WIDGET_ANALOG_MUTE > control type > > Enter > low power state if AA-Path volume is muted. > > > Signed-off-by: > Lydia Wang <lydiawang@viatech. com.cn> > > Signed-off-by: Logan Li > <loganli(a)viatech.com.cn> > Signed-off-by: > Takashi Iwai <tiwai@suse. > de> > > :040000 040000 > ab1ae14ff67f0b08848faeb3ad68def7f3e727f0 > > 0bfbfde11fe32e87e8edbdb3c4d03c2d30370393 M sound > > i'm copypasting > the lspci ouput, so that you can have a general idea > of what kind of > machine i have. please let me know if there is > any other info you need > to solve this bug. > > more details on the problem: > doing > $ arecord -f cd > test.wav > > produces a file of 44 bytes. it's as if no microphone is > attached > to the jack. this behaviour has been evolving from the commit > > i showed you forth. at the beginning, a file with actual data was > > produced, but no audio came out of the speakers when reproducing > it. > going on with the commits, the file became 44 bytes long. > > yours, > > vasilis > > -- > > $ lspci -vvv > > 00:00.0 Host bridge: Advanced Micro Devices > [AMD] RS780 Host Bridge Alternate > Subsystem: ASUSTeK Computer Inc. > Device 83a2 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ > 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ > >SERR- <PERR- INTx- > Latency: 0 > Capabilities: [c4] HyperTransport: > Slave or Primary Interface > Command: BaseUnitID=0 UnitCnt=12 MastHost- > DefDir- DUL- > Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- > <CRCErr=0 IsocEn+ LSEn- ExtCTL- 64b- > Link Config 0: MLWI=16bit > DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- > > Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 > IsocEn- LSEn- ExtCTL- 64b- > Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit > DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- > Revision ID: 3.00 > > Link Frequency 0: [b] > Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- > Link > Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ > 1.0GHz+ 1.2GHz- 1.4GHz- 1.6 GHz- Vend- > Feature Capability: IsocFC- > LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- > Link Frequency 1: 200MHz > Link > Error 1: <Prot- <Ovfl- <EOC- CTLTm- > Link Frequency Capability 1: > 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- > 1.6 GHz- Vend- > Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- > CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- > > Prefetchable memory behind bridge Upper: 00-00 > Bus Number: 00 > > Capabilities: [54] HyperTransport: UnitID Clumping > Capabilities: [40] > HyperTransport: Retry Mode > Capabilities: [9c] HyperTransport: #1a > > Capabilities: [f8] HyperTransport: #1c > > 00:02.0 PCI bridge: Advanced > Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0) (prog-if > 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ > 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- > >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: > primary=00, secondary=01, subordinate=01, sec-latency=0 > I/O behind > bridge: 0000d000- 0000dfff > Memory behind bridge: fea00000-feafffff > > Prefetchable memory behind bridge: 00000000d0000000- 00000000dfffffff > > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- <SERR- <PERR- > BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- > >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > > Capabilities: [50] Power Management version 3 > Flags: PMEClk- DSI- D1- > D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+, D3cold+) > Status: D0 PME- > Enable- DSel=0 DScale=0 PME- > Capabilities: [58] Express (v2) Root Port > (Slot+), MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency > L0s <64ns, L1 <1us > ExtTag+ RBE+ FLReset- > DevCtl: Report errors: > Correctable- Non-Fatal- Fatal- Unsupported- > RlxdOrd+ ExtTag- > PhantFunc- AuxPwr- NoSnoop+ > MaxPayload 128 bytes, MaxReadReq 128 > bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- > TransPend- > LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, > Latency L0 <64ns, L1 <1us > ClockPM- Suprise- LLActRep+ BwNot+ > > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ > > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5 GT/s, > Width x16, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- > SltCap: > AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- > Slot # 2, > PowerLimit 75.000000; Interlock- NoCompl+ > SltCtl: Enable: AttnBtn- > PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- > Control: AttnInd > Unknown, PwrInd Unknown, Power- Interlock- > SltSta: Status: AttnBtn- > PowerFlt- MRL- CmdCplt- PresDet+ Interlock- > Changed: MRL- PresDet+ > LinkState+ > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- > PMEIntEna- CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID > 0000, PMEStatus- PMEPending- > DevCap2: Completion Timeout: Not > Supported, TimeoutDis- ARIFwd- > DevCtl2: Completion Timeout: 50us to > 50ms, TimeoutDis- ARIFwd- > LnkCtl2: Target Link Speed: 5GT/s, > EnterCompliance- SpeedDis-, Selectable De- emphasis: -3.5dB > Transmit > Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- > > Compliance De- emphasis: -6dB > LnkSta2: Current De-emphasis Level: > -3.5dB > Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- > Count=1/1 Enable+ > Address: fee0f00c Data: 4159 > Capabilities: [b0] > Subsystem: ASUSTeK Computer Inc. Device 83a2 > Capabilities: [b8] > HyperTransport: MSI Mapping Enable+ Fixed+ > Capabilities: [100] Vendor > Specific Information <?> > Capabilities: [110] Virtual Channel <?> > > Kernel driver in use: pcieport-driver > > 00:0a.0 PCI bridge: Advanced > Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 5) (prog-if 00 > [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ > 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- > >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: > primary=00, secondary=02, subordinate=02, sec- latency=0 > I/O behind > bridge: 0000e000-0000efff > Memory behind bridge: feb00000-febfffff > > Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff > > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- <SERR- <PERR- > BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- > >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > > Capabilities: [50] Power Management version 3 > Flags: PMEClk- DSI- D1- > D2- AuxCurrent=0mA PME(D0+,D1- ,D2-,D3hot+,D3cold+) > Status: D0 PME- > Enable- DSel=0 DScale=0 PME- > Capabilities: [58] Express (v2) Root Port > (Slot+), MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency > L0s <64ns, L1 <1us > ExtTag+ RBE+ FLReset- > DevCtl: Report errors: > Correctable- Non-Fatal- Fatal- Unsupported- > RlxdOrd+ ExtTag- > PhantFunc- AuxPwr- NoSnoop+ > MaxPayload 128 bytes, MaxReadReq 128 > bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- > TransPend- > LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, > Latency L0 <64ns, L1 <1us > ClockPM- Suprise- LLActRep+ BwNot+ > > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ > > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, > Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- > SltCap: > AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- > Slot # a, > PowerLimit 25.000000; Interlock- NoCompl+ > SltCtl: Enable: AttnBtn- > PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- > Control: AttnInd > Unknown, PwrInd Unknown, Power- Interlock- > SltSta: Status: AttnBtn- > PowerFlt- MRL- CmdCplt- PresDet+ Interlock- > Changed: MRL- PresDet+ > LinkState+ > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- > PMEIntEna- CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID > 0000, PMEStatus- PMEPending- > DevCap2: Completion Timeout: Not > Supported, TimeoutDis- ARIFwd- > DevCtl2: Completion Timeout: 50us to > 50ms, TimeoutDis- ARIFwd- > LnkCtl2: Target Link Speed: 2.5GT/s, > EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB > Transmit > Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- > > Compliance De- emphasis: -6dB > LnkSta2: Current De-emphasis Level: > -6dB > Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- > Count=1/1 Enable+ > Address: fee0f00c Data: 4161 > Capabilities: [b0] > Subsystem: ASUSTeK Computer Inc. Device 83a2 > Capabilities: [b8] > HyperTransport: MSI Mapping Enable+ Fixed+ > Capabilities: [100] Vendor > Specific Information <?> > Capabilities: [110] Virtual Channel <?> > > Kernel driver in use: pcieport-driver > > 00:11.0 SATA controller: ATI > Technologies Inc SB700/SB800 SATA Controller [AHCI mode] (prog-if 01 > [AHCI 1.0]) > Subsystem: ASUSTeK Computer Inc. Device 8389 > Control: > I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- > SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- > DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: > 64, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 22 > > Region 0: I/O ports at c000 [size=8] > Region 1: I/O ports at b000 > [size=4] > Region 2: I/O ports at a000 [size=8] > Region 3: I/O ports at > 9000 [size=4] > Region 4: I/O ports at 8000 [size=16] > Region 5: Memory > at fe9ffc00 (32-bit, non-prefetchable) [size=1K] > Capabilities: [60] > Power Management version 2 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME- Enable- DSel=0 > DScale=0 PME- > Capabilities: [70] SATA HBA <?> > Kernel driver in use: > ahci > > 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB > OHCI0 Controller (prog-if 10 [OHCI]) > Subsystem: ASUSTeK Computer Inc. > Device 8389 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap- > 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- > >SERR- <PERR- INTx- > Latency: 64, Cache Line Size: 64 bytes > Interrupt: > pin A routed to IRQ 16 > Region 0: Memory at fe9fe000 (32-bit, non- > prefetchable) [size=4K] > Kernel driver in use: ohci_hcd > Kernel > modules: ohci- hcd > > 00:12.1 USB Controller: ATI Technologies Inc SB700 > USB OHCI1 Controller (prog-if 10 [OHCI]) > Subsystem: ASUSTeK Computer > Inc. Device 8389 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ > VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap- > 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- > >SERR- <PERR- INTx- > Latency: 64, Cache Line Size: 64 bytes > Interrupt: > pin A routed to IRQ 16 > Region 0: Memory at fe9fd000 (32-bit, non- > prefetchable) [size=4K] > Kernel driver in use: ohci_hcd > Kernel > modules: ohci-hcd > > 00:12.2 USB Controller: ATI Technologies Inc > SB700/SB800 USB EHCI Controller (prog-if 20 [EHCI]) > Subsystem: ASUSTeK > Computer Inc. Device 8389 > Control: I/O- Mem+ BusMaster+ SpecCycle- > MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: > Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 64, Cache Line Size: 64 bytes > > Interrupt: pin B routed to IRQ 17 > Region 0: Memory at fe9ff800 (32- > bit, non-prefetchable) [size=256] > Capabilities: [c0] Power Management > version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+, > D3hot+,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Bridge: > PM- B3+ > Capabilities: [e4] Debug port: BAR=1 offset=00e0 > Kernel > driver in use: ehci_hcd > Kernel modules: ehci-hcd > > 00:13.0 USB > Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller (prog- > if 10 [OHCI]) > Subsystem: ASUSTeK Computer Inc. Device 8389 > Control: > I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- > SERR+ FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- > DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: > 64, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 18 > > Region 0: Memory at fe9fc000 (32-bit, non-prefetchable) [size=4K] > > Kernel driver in use: ohci_hcd > Kernel modules: ohci-hcd > > 00:13.1 USB > Controller: ATI Technologies Inc SB700 USB OHCI1 Controller (prog-if 10 > [OHCI]) > Subsystem: ASUSTeK Computer Inc. Device 8389 > Control: I/O+ > Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ > FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- > DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: > 64, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 18 > > Region 0: Memory at fe9fb000 (32-bit, non- prefetchable) [size=4K] > > Kernel driver in use: ohci_hcd > Kernel modules: ohci-hcd > > 00:13.2 USB > Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller (prog- > if 20 [EHCI]) > Subsystem: ASUSTeK Computer Inc. Device 8389 > Control: > I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- > SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- > DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: > 64, Cache Line Size: 64 bytes > Interrupt: pin B routed to IRQ 19 > > Region 0: Memory at fe9ff400 (32-bit, non-prefetchable) [size=256] > > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1+ > D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) > Status: D0 PME- > Enable- DSel=0 DScale=0 PME- > Bridge: PM- B3+ > Capabilities: [e4] > Debug port: BAR=1 offset=00e0 > Kernel driver in use: ehci_hcd > Kernel > modules: ehci-hcd > > 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus > Controller (rev 3c) > Subsystem: ASUSTeK Computer Inc. Device 8389 > > Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz+ UDF- FastB2B- > ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort- >SERR- <PERR- INTx- > > Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+ > > 00:14.1 > IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller (prog-if > 8a [Master SecP PriP]) > Subsystem: ASUSTeK Computer Inc. Device 8389 > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B- > ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > > Latency: 64 > Interrupt: pin A routed to IRQ 16 > Region 0: I/O ports at > 01f0 [size=8] > Region 1: I/O ports at 03f4 [size=1] > Region 2: I/O > ports at 0170 [size=8] > Region 3: I/O ports at 0374 [size=1] > Region 4: > I/O ports at ff00 [size=16] > Capabilities: [70] Message Signalled > Interrupts: Mask- 64bit- Count=1/1 Enable- > Address: 00000000 Data: > 0000 > Kernel driver in use: pata_atiixp > > 00:14.2 Audio device: ATI > Technologies Inc SBx00 Azalia (Intel HDA) > Subsystem: ASUSTeK Computer > Inc. Device 836c > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ > 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- > >SERR- <PERR- INTx- > Latency: 64, Cache Line Size: 64 bytes > Interrupt: > pin ? routed to IRQ 16 > Region 0: Memory at fe9f4000 (64-bit, non- > prefetchable) [size=16K] > Capabilities: [50] Power Management version 2 > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-, D3hot+, > D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Kernel driver > in use: HDA Intel > Kernel modules: snd-hda-intel > > 00:14.3 ISA bridge: > ATI Technologies Inc SB700/SB800 LPC host controller > Subsystem: > ASUSTeK Computer Inc. Device 8389 > Control: I/O+ Mem+ BusMaster+ > SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > > Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > > 00:14.4 PCI bridge: > ATI Technologies Inc SBx00 PCI to PCI Bridge (prog-if 01 [Subtractive > decode]) > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- > FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- > INTx- > Latency: 64 > Bus: primary=00, secondary=03, subordinate=03, sec- > latency=64 > I/O behind bridge: 0000f000- 00000fff > Memory behind bridge: > fff00000-000fffff > Prefetchable memory behind bridge: fff00000-000fffff > > Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity+ SERR+ NoISA+ VGA- > MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- > DiscTmrSERREn- > > 00:14.5 USB Controller: ATI Technologies Inc > SB700/SB800 USB OHCI2 Controller (prog-if 10 [OHCI]) > Subsystem: > ASUSTeK Computer Inc. Device 8389 > Control: I/O- Mem+ BusMaster+ > SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64, Cache Line Size: 64 > bytes > Interrupt: pin C routed to IRQ 18 > Region 0: Memory at fe9fa000 > (32-bit, non-prefetchable) [size=4K] > Kernel driver in use: ohci_hcd > > Kernel modules: ohci-hcd > > 00:18.0 Host bridge: Advanced Micro Devices > [AMD] Family 10h [Opteron, Athlon64, Sempron] HyperTransport > Configuration > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ > 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- > >SERR- <PERR- INTx- > Capabilities: [80] HyperTransport: Host or > Secondary Interface > Command: WarmRst+ DblEnd- DevNum=0 ChainSide- > HostHide+ Slave- <EOCErr- DUL- > Link Control: CFlE- CST- CFE- <LkFail- > Init+ EOC- TXO- <CRCErr=0 IsocEn+ LSEn+ ExtCTL- 64b- > Link Config: > MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit > DwFcOutEn- > Revision ID: 3.00 > Link Frequency: [b] > Link Error: > <Prot- <Ovfl- <EOC- CTLTm- > Link Frequency Capability: 200MHz+ 300MHz- > 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4 GHz- 1.6GHz- Vend- > > Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- > UCnfE- > > 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h > [Opteron, Athlon64, Sempron] Address Map > Control: I/O- Mem- BusMaster- > SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > > 00: 18.2 Host bridge: Advanced > Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] DRAM > Controller > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- > ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- > FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- > INTx- > Kernel modules: amd64_edac_mod > > 00:18.3 Host bridge: Advanced > Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] > Miscellaneous Control > Control: I/O- Mem- BusMaster- SpecCycle- > MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: > Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Capabilities: [f0] Secure device <?> > > 00: > 18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, > Athlon64, Sempron] Link Control > Control: I/O- Mem- BusMaster- > SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > > 01:00.0 VGA compatible > controller: ATI Technologies Inc Device 954f (prog-if 00 [VGA > controller]) > Subsystem: ASUSTeK Computer Inc. Device 02a8 > Control: > I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- > SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- > DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, > Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 18 > Region 0: > Memory at d0000000 (64-bit, prefetchable) [size=256M] > Region 2: Memory > at feaf0000 (64-bit, non-prefetchable) [size=64K] > Region 4: I/O ports > at d000 [size=256] > Expansion ROM at feac0000 [disabled] [size=128K] > > Capabilities: [50] Power Management version 3 > Flags: PMEClk- DSI- D1+ > D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME- > Enable- DSel=0 DScale=0 PME- > Capabilities: [58] Express (v2) Legacy > Endpoint, MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency > L0s <4us, L1 unlimited > ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ > FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ > > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- > UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- > LnkCap: Port #0, > Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us > > ClockPM- Suprise- LLActRep- BwNot- > LnkCtl: ASPM Disabled; RCB 64 > bytes Disabled- Retrain- CommClk+ > ExtSynch- ClockPM- AutWidDis- > BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- > SlotClk+ DLActive- BWMgmt- ABWMgmt- > DevCap2: Completion Timeout: Not > Supported, TimeoutDis- > DevCtl2: Completion Timeout: 50us to 50ms, > TimeoutDis- > LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- > SpeedDis-, Selectable De-emphasis: -6dB > Transmit Margin: Normal > Operating Range, EnterModifiedCompliance- ComplianceSOS- > Compliance > De-emphasis: -6dB > LnkSta2: Current De-emphasis Level: -6dB > > Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Count=1/1 > Enable- > Address: 0000000000000000 Data: 0000 > Capabilities: [100] > Vendor Specific Information <?> > > 01:00.1 Audio device: ATI Technologies > Inc Device aa38 > Subsystem: ASUSTeK Computer Inc. Device aa38 > Control: > I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- > SERR+ FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- > DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, > Cache Line Size: 64 bytes > Interrupt: pin B routed to IRQ 28 > Region 0: > Memory at feaec000 (64-bit, non- prefetchable) [size=16K] > Capabilities: > [50] Power Management version 3 > Flags: PMEClk- DSI- D1+ D2+ > AuxCurrent=0mA PME(D0-,D1- , D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- > DSel=0 DScale=0 PME- > Capabilities: [58] Express (v2) Legacy Endpoint, > MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, > L1 unlimited > ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- > > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- > > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ > MaxPayload 128 bytes, > MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- > AuxPwr- TransPend- > LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM > L0s L1, Latency L0 <64ns, L1 <1us > ClockPM- Suprise- LLActRep- BwNot- > > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ > > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, > Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- > DevCap2: > Completion Timeout: Not Supported, TimeoutDis- > DevCtl2: Completion > Timeout: 50us to 50ms, TimeoutDis- > LnkCtl2: Target Link Speed: 2.5 > GT/s, EnterCompliance- SpeedDis-, Selectable De- emphasis: -6dB > > Transmit Margin: Normal Operating Range, EnterModifiedCompliance- > ComplianceSOS- > Compliance De- emphasis: -6dB > LnkSta2: Current De- > emphasis Level: -6dB > Capabilities: [a0] Message Signalled Interrupts: > Mask- 64bit+ Count=1/1 Enable+ > Address: 00000000fee0f00c Data: 4189 > > Capabilities: [100] Vendor Specific Information <?> > Kernel driver in > use: HDA Intel > Kernel modules: snd-hda-intel > > 02:00.0 Ethernet > controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express > Gigabit Ethernet controller (rev 03) > Subsystem: ASUSTeK Computer Inc. > Device 83a3 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ > 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- > >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: > pin A routed to IRQ 27 > Region 0: I/O ports at e800 [size=256] > Region > 2: Memory at fdfff000 (64- bit, prefetchable) [size=4K] > Region 4: > Memory at fdff8000 (64- bit, prefetchable) [size=16K] > Expansion ROM at > febf0000 [disabled] [size=64K] > Capabilities: [40] Power Management > version 3 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+, D1+, > D2+,D3hot+,D3cold+) > Status: D0 PME- Enable- DSel=0 DScale=0 PME- > > Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Count=1/1 > Enable+ > Address: 00000000fee0f00c Data: 4179 > Capabilities: [70] > Express (v2) Endpoint, MSI 01 > DevCap: MaxPayload 256 bytes, PhantFunc > 0, Latency L0s <512ns, L1 <64us > ExtTag- AttnBtn- AttnInd- PwrInd- > RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > > MaxPayload 128 bytes, MaxReadReq 4096 bytes > DevSta: CorrErr+ > UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend- > LnkCap: Port #0, > Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us > > ClockPM+ Suprise- LLActRep- BwNot- > LnkCtl: ASPM Disabled; RCB 64 > bytes Disabled- Retrain- CommClk+ > ExtSynch- ClockPM- AutWidDis- > BWInt- AutBWInt- > LnkSta: Speed 2.5 GT/s, Width x1, TrErr- Train- > SlotClk+ DLActive- BWMgmt- ABWMgmt- > DevCap2: Completion Timeout: Not > Supported, TimeoutDis+ > DevCtl2: Completion Timeout: 50us to 50ms, > TimeoutDis- > LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- > SpeedDis-, Selectable De-emphasis: -6dB > Transmit Margin: Normal > Operating Range, EnterModifiedCompliance- ComplianceSOS- > Compliance > De- emphasis: -6dB > LnkSta2: Current De-emphasis Level: -6dB > > Capabilities: [ac] MSI-X: Enable- Mask- TabSize=4 > Vector table: BAR=4 > offset=00000000 > PBA: BAR=4 offset=00000800 > Capabilities: [cc] Vital > Product Data <?> > Capabilities: [100] Advanced Error Reporting > UESta: > DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- > UnsupReq- ACSVoil- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- > UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSVoil- > UESvrt: DLP+ SDES+ > TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- > ACSVoil- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr+ > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- > NonFatalErr+ > AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ > ChkEn- > Capabilities: [140] Virtual Channel <?> > Capabilities: [160] > Device Serial Number 00- 00-00-00-00-00-00-00 > Kernel driver in use: > r8169 > > > > > Risparmia con Tutto Incluso Light: telefono + adsl 8 mega a soli 14,95 € al mese. > > Gratis la Sim Tiscali Mobile con 25 euro di traffico! > > L'offerta è valida solo se attivi entro il 20/05/10 > > http: //abbonati.tiscali. it/telefono-adsl/prodotti/tc/tuttoincluso_light/?WT. mc_id=01fw > _______________________________________________ Alsa- devel mailing list Alsa-devel(a)alsa-project.org http://mailman.alsa- project. org/mailman/listinfo/alsa-devel Trova Casa sul portale immobiliare n°1 in Italia http://tiscali.casa.it Trova Casa sul portale immobiliare n°1 in Italia http://tiscali.casa.it

1 0

[alsa-devel] Type safe Haskell interface to ALSA sequencer
by Henning Thielemann 25 May '10

25 May '10

Dear ALSA developers, I read the ALSA-Sequencer-API-Doxygen documentation, various ALSA-MIDI-How-Tos and their examples and succeeded to work with ALSA sequencers in Haskell. However, I'm still uncertain about the meaning of the system components and how they interact. It is extensively documented, what works, but not, what does not work. Whenever I do a mistake, ALSA leaves me with an unspecific "operation not permitted" or "invalid argument" error code. Thus I try to encode conditions in Haskell types. For instance once I got an "Invalid argument" error code and only after some investigation, I found that I opened the sequencer in Output mode but later called event_input. (Actually I only wanted to output something, but used event_input for synchronization using Echo events. Unfortunately the intention of Echo messages is even not explained in the Doxygen stuff.) In order to prevent another occurrence of this problem, I defined distinct Haskell types for sequencers depending on the input mode. Now, event_input is only allowed on sequencers that were opened in Output or Duplex mode. However I wondered, why I could create writeable ports in a output-only sequencer. Does this make sense? Would it be reasonable to forbid writeable ports in output sequencers and readable ports in input sequencers by Haskell types? Is there a difference between cap_read|cap_write and cap_duplex? I also wondered why there can be several ports in one sequencer, since multiple clients can connect to one port, and event_input and event_output have no port argument. Further I wondered why queues are not bound to a specific port. Can queues be shared amongst ports? Is it sensible to have multiple queues in one sequencer? Why has sync_output_queue no queue argument? The more I think about it, it seems to me that a port is more an identifier, a part of an address, than a mailbox. I could use ports as tags, that tell which part of an application to control. A queue looks like a mail company and I can use the same sender and receiver addresses across different companies. If this is true, then I think it would be worth to mention this in the API documentation. In another example I called sync_output_queue in order to wait for all events being sent, but it aborted with "Operation not permitted", whereas I have seen example code where it works. What are the preconditions to calling sync_output_queue? I really like to see a picture of how sequencers, clients, ports, port_infos, queues, timers, events are related.

2 1

[alsa-devel] [PATCH 1/1] ALSA: usb-audio: add support for Akai MPD16
by Krzysztof Foltman 25 May '10

25 May '10

The decoding/encoding is based on own reverse-engineering. Both control and data ports are handled. Writing to control port supports SysEx events only, as this is the only type of messages that MPD16 recognizes. Signed-off-by: Krzysztof Foltman <wdev(a)foltman.com> diff --git a/sound/usb/midi.c b/sound/usb/midi.c index 2c1558c..d669feb 100644 --- a/sound/usb/midi.c +++ b/sound/usb/midi.c @@ -434,7 +434,7 @@ static void snd_usbmidi_maudio_broken_running_status_input( u8 cin = buffer[i] & 0x0f; struct usbmidi_in_port *port = &ep->ports[cable]; int length; - + length = snd_usbmidi_cin_length[cin]; if (cin == 0xf && buffer[i + 1] >= 0xf8) ; /* realtime msg: no running status change */ @@ -628,13 +628,13 @@ static struct usb_protocol_ops snd_usbmidi_standard_ops = { static struct usb_protocol_ops snd_usbmidi_midiman_ops = { .input = snd_usbmidi_midiman_input, - .output = snd_usbmidi_standard_output, + .output = snd_usbmidi_standard_output, .output_packet = snd_usbmidi_output_midiman_packet, }; static struct usb_protocol_ops snd_usbmidi_maudio_broken_running_status_ops = { .input = snd_usbmidi_maudio_broken_running_status_input, - .output = snd_usbmidi_standard_output, + .output = snd_usbmidi_standard_output, .output_packet = snd_usbmidi_output_standard_packet, }; @@ -645,6 +645,110 @@ static struct usb_protocol_ops snd_usbmidi_cme_ops = { }; /* + * AKAI MPD16 protocol: + * + * For control port (endpoint 1): + * ============================== + * One or more chunks consisting of first byte of (0x10 | msg_len) and then a + * SysEx message (msg_len=9 bytes long): + * + * F0 47 62 60 aa bb cc xx F7 (xx = (aa + bb + cc) & 0x7F) + * + * aa bb cc + * -------- + * 10 01 7E edit mode on? + * 10 01 00 edit mode off? + * 10 04 7F select bank 1 + * 10 04 00 select bank 0 + * 11 pp nn set pad pp to send note nn + * 12 pp ss set sensitivity on pad pp to ss + * 13 00 cc set slider CC number to cc + * 14 00 cc set MIDI channel to cc + * 15 01 pp request note number for pad pp (returns 20 pp nn) + * 15 02 pp request sensitivity for pad pp (returns 21 pp ss) + * 15 03 00 request slider CC number (returns 22 00 cc) + * 15 05 00 request MIDI channel number (returns 23 00 cc) + * + * For data port (endpoint 2): + * =========================== + * One or more chunks consisting of first byte of (0x20 | msg_len) and then a + * MIDI message (msg_len bytes long) + * + * Messages sent: + * 21 FE (active sense) + * 23 90 xx xx (note on) + * 23 Ax xx xx (polyphonic pressure) + * 23 Bx xx xx (control change) + */ +static void snd_usbmidi_akai_input(struct snd_usb_midi_in_endpoint *ep, + uint8_t *buffer, int buffer_length) +{ + unsigned int pos = 0; + unsigned int len = (unsigned int)buffer_length; + while (pos < len) { + int port = (buffer[pos] >> 4) - 1; + unsigned int msg_len = buffer[pos] & 0x0f; + pos++; + if (pos + msg_len <= len && (port == 0 || port == 1)) + snd_usbmidi_input_data(ep, 0, &buffer[pos], msg_len); + pos += msg_len; + } +} + +static void snd_usbmidi_akai_output(struct snd_usb_midi_out_endpoint *ep, + struct urb *urb) +{ + uint8_t *msg; + uint8_t *plen = &ep->ports[0].data[0]; /* length so far */ + int count; + uint8_t tmp; + + if (!ep->ports[0].active) + return; + + msg = urb->transfer_buffer + urb->transfer_buffer_length; + + /* only try adding more data when there's space for at least 1 SysEx */ + while (urb->transfer_buffer_length + 16 < ep->max_transfer) { + count = snd_rawmidi_transmit(ep->ports[0].substream, &tmp, 1); + if (count < 1) { + ep->ports[0].active = 0; + return; + } + if (ep->ports[0].state == STATE_UNKNOWN) { + /* only accept SysEx'es, skip everything else */ + if (tmp != 0xF0) + continue; + /* start accumulating SysEx data */ + *plen = 0x00; + ep->ports[0].state = STATE_SYSEX_0; + } + if (*plen > 14) { + /* SysEx too long, drop it and start over */ + ep->ports[0].state = STATE_UNKNOWN; + continue; + } + msg[++(*plen)] = tmp; + if (tmp == 0xF7) { + /* add total size (w/hdr) to length-to-transfer */ + urb->transfer_buffer_length += 1 + *plen; + /* set port number nibble in the header */ + msg[0] = 0x10 | *plen; + msg += 1 + *plen; + + /* go back to waiting for SysEx */ + ep->ports[0].state = STATE_UNKNOWN; + continue; + } + } +} + +static struct usb_protocol_ops snd_usbmidi_akai_ops = { + .input = snd_usbmidi_akai_input, + .output = snd_usbmidi_akai_output, +}; + +/* * Novation USB MIDI protocol: number of data bytes is in the first byte * (when receiving) (+1!) or in the second byte (when sending); data begins * at the third byte. @@ -1434,6 +1538,9 @@ static struct port_info { EXTERNAL_PORT(0x086a, 0x0001, 8, "%s Broadcast"), EXTERNAL_PORT(0x086a, 0x0002, 8, "%s Broadcast"), EXTERNAL_PORT(0x086a, 0x0003, 4, "%s Broadcast"), + /* Akai MPD16 */ + CONTROL_PORT(0x09e8, 0x0062, 0, "%s Control"), + EXTERNAL_PORT(0x09e8, 0x0062, 1, "%s MIDI"), /* Access Music Virus TI */ EXTERNAL_PORT(0x133e, 0x0815, 0, "%s MIDI"), PORT_INFO(0x133e, 0x0815, 1, "%s Synth", 0, @@ -1707,7 +1814,7 @@ static int snd_usbmidi_detect_endpoints(struct snd_usb_midi* umidi, snd_usbmidi_switch_roland_altsetting(umidi); if (endpoint[0].out_ep || endpoint[0].in_ep) - return 0; + return 0; intf = umidi->iface; if (!intf || intf->num_altsetting < 1) @@ -1745,7 +1852,7 @@ static int snd_usbmidi_detect_per_port_endpoints(struct snd_usb_midi* umidi, struct snd_usb_midi_endpoint_info* endpoints) { int err, i; - + err = snd_usbmidi_detect_endpoints(umidi, endpoints, MIDI_MAX_ENDPOINTS); for (i = 0; i < MIDI_MAX_ENDPOINTS; ++i) { if (endpoints[i].out_ep) @@ -2035,6 +2142,12 @@ int snd_usbmidi_create(struct snd_card *card, umidi->usb_protocol_ops = &snd_usbmidi_cme_ops; err = snd_usbmidi_detect_per_port_endpoints(umidi, endpoints); break; + case QUIRK_MIDI_AKAI: + umidi->usb_protocol_ops = &snd_usbmidi_akai_ops; + err = snd_usbmidi_detect_per_port_endpoints(umidi, endpoints); + /* endpoint 1 is input-only */ + endpoints[1].out_cables = 0; + break; default: snd_printd(KERN_ERR "invalid quirk type %d\n", quirk->type); err = -ENXIO; diff --git a/sound/usb/midi.h b/sound/usb/midi.h index 2089ec9..2fca80b 100644 --- a/sound/usb/midi.h +++ b/sound/usb/midi.h @@ -37,6 +37,8 @@ struct snd_usb_midi_endpoint_info { /* for QUIRK_MIDI_CME, data is NULL */ +/* for QUIRK_MIDI_AKAI, data is NULL */ + int snd_usbmidi_create(struct snd_card *card, struct usb_interface *iface, struct list_head *midi_list, diff --git a/sound/usb/quirks-table.h b/sound/usb/quirks-table.h index 91ddef3..f8797f6 100644 --- a/sound/usb/quirks-table.h +++ b/sound/usb/quirks-table.h @@ -1973,6 +1973,17 @@ YAMAHA_DEVICE(0x7010, "UB99"), } }, +/* AKAI devices */ +{ + USB_DEVICE(0x09e8, 0x0062), + .driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) { + .vendor_name = "AKAI", + .product_name = "MPD16", + .ifnum = 0, + .type = QUIRK_MIDI_AKAI, + } +}, + /* TerraTec devices */ { USB_DEVICE_VENDOR_SPEC(0x0ccd, 0x0012), diff --git a/sound/usb/quirks.c b/sound/usb/quirks.c index 136e5b4..b45e54c 100644 --- a/sound/usb/quirks.c +++ b/sound/usb/quirks.c @@ -289,6 +289,7 @@ int snd_usb_create_quirk(struct snd_usb_audio *chip, [QUIRK_MIDI_FASTLANE] = create_any_midi_quirk, [QUIRK_MIDI_EMAGIC] = create_any_midi_quirk, [QUIRK_MIDI_CME] = create_any_midi_quirk, + [QUIRK_MIDI_AKAI] = create_any_midi_quirk, [QUIRK_AUDIO_STANDARD_INTERFACE] = create_standard_audio_quirk, [QUIRK_AUDIO_FIXED_ENDPOINT] = create_fixed_stream_quirk, [QUIRK_AUDIO_EDIROL_UAXX] = create_uaxx_quirk, diff --git a/sound/usb/usbaudio.h b/sound/usb/usbaudio.h index d679e72..06ebf24 100644 --- a/sound/usb/usbaudio.h +++ b/sound/usb/usbaudio.h @@ -74,6 +74,7 @@ enum quirk_type { QUIRK_MIDI_FASTLANE, QUIRK_MIDI_EMAGIC, QUIRK_MIDI_CME, + QUIRK_MIDI_AKAI, QUIRK_MIDI_US122L, QUIRK_AUDIO_STANDARD_INTERFACE, QUIRK_AUDIO_FIXED_ENDPOINT, -- 1.7.0.4

3 5

[alsa-devel] MMAP in ALSA
by Varadarajan, Srikanth 25 May '10

25 May '10

Hi All, I am new to the list and ALSA. For the hardware I am working with, we expose it to ALSA as one card capable of playing one PCM stream. If we have one application using the hardware through ALSA, other applications are unable to get access to it. So, we want to have PulseAudio on top and use the pulse virtual device to render audio through ALSA. Is this a recommended way of having multiple applications access one audio HW simultaneously? Is there any other way of handling multiple applications get access to the same hardware? Also, why are mmap and munmap operations required in ALSA? Right now, we do not have mmap and munmap operations exposed. Though the hardware constraints have "SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_MMAP_VALID" defined. Looks like, if we have to PulseAudio on top, mmap operations are required in ALSA. If there is a close enough ALSA implementation in the current Linux kernel that I can lookup, please point me to that. Any help/suggestions are welcome. Thanks, Srikanth

3 2

[alsa-devel] Query about code organization for kernel driver.
by Anksh Agarwal 25 May '10

25 May '10

Hi Everyone, I am currently working on a custom ARM based board and have succeeded in running alsa on my target. In this reference I have some basic queries and would be great if someone could give me pointers.This would help me in rorganizing the code as per acceptance from the group. since we planning to support a list of devices I wanted to keep the interface independent of playback/record session.this helps in switching to different devices in middle of playback. At any point a single device would be enabled. So i have another driver snd_device.c which uses sysfs interface to get device index or name to enable/disable device. The reason for this was that we could reuse a lot of code from the alsa-plugin(maemo). But then will it be right to put the device enable/disable code under sound/soc/xxxx/snd_device.c path, or can we split and place it seperately under sound/driver/xxxx/snd_device.c or any other suggested directory? i am not aware how to split the audio path enable/disable code from the soc driver and which would be ideal directory to place them, since there is hardly any interaction between playback and device enable/disable routines? I think the device enable/disable code outside sound/ directory wont be a good idea as its to be specifically used by alsa playback/record only. please suggest as this would help me a lot. Also let me know if any more info would help to get to a better conclusion. Really appreciate all the help. Thanks, Anksh

2 1

[alsa-devel] [PATCH] ASoC: fix uninitialised variable in siu_dai.c
by Guennadi Liakhovetski 24 May '10

24 May '10

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski(a)gmx.de> --- Strangely, the compiler doesn't warn about this one, but I really don't see how this can be correct. Am I being blind? sound/soc/sh/siu_dai.c | 2 ++ 1 files changed, 2 insertions(+), 0 deletions(-) diff --git a/sound/soc/sh/siu_dai.c b/sound/soc/sh/siu_dai.c index d86ee1b..eeed5ed 100644 --- a/sound/soc/sh/siu_dai.c +++ b/sound/soc/sh/siu_dai.c @@ -588,6 +588,8 @@ static int siu_dai_prepare(struct snd_pcm_substream *substream, ret = siu_dai_spbstart(port_info); if (ret < 0) goto fail; + } else { + ret = 0; } port_info->play_cap |= self; -- 1.6.2.4

3 2

[alsa-devel] [PATCH] ASoC: Update Freescale i.MX SSI driver
by Stuart Longland 24 May '10

24 May '10

Hi all, Attached is a patch that corrects the i.MX SSI driver so that it compiles against the latest ASoC tree. I'm able to compile the driver with this patch, but haven't done any testing beyond this point... the update is quite naïve, based on changes I had seen to other drivers. I hope to give it a try on Monday, but in the meantime, here's the patch for others to try. -- Stuart Longland (aka Redhatter, VK4MSL) .'''. Gentoo Linux/MIPS Cobalt and Docs Developer '.'` : . . . . . . . . . . . . . . . . . . . . . . .'.' http://dev.gentoo.org/~redhatter :.' I haven't lost my mind... ...it's backed up on a tape somewhere.

3 2

Re: [alsa-devel] [PATCH v3] NUC900/audio: Add nuc900 audio driver
by Mark Brown 24 May '10

24 May '10

On Sat, May 22, 2010 at 09:46:31PM +0800, Wan ZongShun wrote: > Dear Liam & Mark, > > This patch fixed some issues according to your comments. > Here and now, I adjusted the driver and called it v3 for resubmitting. Since your patch has already been applied please submit incremental updates rather than a revised version of the full patch.

2 1

[alsa-devel] [PATCH 024/199] Documentation/sound/alsa/emu10k1-jack.txt: Checkpatch cleanup
by Andrea Gelmini 23 May '10

23 May '10

Documentation/sound/alsa/emu10k1-jack.txt:3: ERROR: trailing whitespace Documentation/sound/alsa/emu10k1-jack.txt:39: ERROR: trailing whitespace Documentation/sound/alsa/emu10k1-jack.txt:58: ERROR: trailing whitespace Signed-off-by: Andrea Gelmini <andrea.gelmini(a)gelma.net> --- Documentation/sound/alsa/emu10k1-jack.txt | 6 +++--- 1 files changed, 3 insertions(+), 3 deletions(-) diff --git a/Documentation/sound/alsa/emu10k1-jack.txt b/Documentation/sound/alsa/emu10k1-jack.txt index 751d450..3cc6548 100644 --- a/Documentation/sound/alsa/emu10k1-jack.txt +++ b/Documentation/sound/alsa/emu10k1-jack.txt @@ -1,6 +1,6 @@ This document is a guide to using the emu10k1 based devices with JACK for low latency, multichannel recording functionality. All of my recent work to allow -Linux users to use the full capabilities of their hardware has been inspired +Linux users to use the full capabilities of their hardware has been inspired by the kX Project. Without their work I never would have discovered the true power of this hardware. @@ -36,7 +36,7 @@ The 16 input ports are connected to the 16 physical inputs. Contrary to popular belief, all emu10k1 cards are multichannel cards. Which of these input channels have physical inputs connected to them depends on the card model. Trial and error is highly recommended; the pinout diagrams -for the card have been reverse engineered by some enterprising kX users and are +for the card have been reverse engineered by some enterprising kX users and are available on the internet. Meterbridge is helpful here, and the kX forums are packed with useful information. @@ -55,7 +55,7 @@ JACK Epilog FXBUS2(nr) -------------------------------------------- capture_1 asio14 FXBUS2(0xe) capture_2 asio15 FXBUS2(0xf) -capture_3 asio0 FXBUS2(0x0) +capture_3 asio0 FXBUS2(0x0) ~capture_4 Center EXTOUT(0x11) // mapped to by Center ~capture_5 LFE EXTOUT(0x12) // mapped to by LFE capture_6 asio3 FXBUS2(0x3) -- 1.7.1.251.gf80a2

1 1

[alsa-devel] [PATCH 092/199] Documentation/sound/oss/ALS: Checkpatch cleanup
by Andrea Gelmini 23 May '10

23 May '10

Documentation/sound/oss/ALS:15: ERROR: trailing whitespace Documentation/sound/oss/ALS:40: ERROR: trailing whitespace Documentation/sound/oss/ALS:55: ERROR: trailing whitespace Documentation/sound/oss/ALS:56: ERROR: trailing whitespace Signed-off-by: Andrea Gelmini <andrea.gelmini(a)gelma.net> --- Documentation/sound/oss/ALS | 8 ++++---- 1 files changed, 4 insertions(+), 4 deletions(-) diff --git a/Documentation/sound/oss/ALS b/Documentation/sound/oss/ALS index d01ffbf..282a2e1 100644 --- a/Documentation/sound/oss/ALS +++ b/Documentation/sound/oss/ALS @@ -12,7 +12,7 @@ SB16 driver). To use an ALS sound card under Linux, enable the following options as modules in the sound configuration section of the kernel config: - 100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support - - FM synthesizer (YM3812/OPL-3) support + - FM synthesizer (YM3812/OPL-3) support - standalone MPU401 support may be required for some cards; for the ALS-007, when using isapnptools, it is required Since the ALS-007/100/200 are PnP cards, ISAPnP support should probably be @@ -37,7 +37,7 @@ requires they be different. For "sb", "io", "irq" and "dma" should be set to the same values used to configure the audio section of the card with isapnp. "dma16" should be explicitly set to "-1" for an ALS-007 since this card does not have a 16 bit dma channel; if not specified the kernel will -default to using channel 5 anyway which will cause audio not to work. +default to using channel 5 anyway which will cause audio not to work. "mpu_io" should be set to 0. The "io" parameter of the "opl3" module should also agree with the setting used by isapnp. To get the MPU401 interface working on an ALS-007 card, the "mpu401" module will be required since this @@ -52,8 +52,8 @@ The resulting sound driver will provide the following capabilities: - Software selection of record source (line in, CD, FM, mic, master) - Record and playback of midi data via the external MPU-401 - Playback of midi data using inbuilt FM synthesizer - - Control of the ALS-007 mixer via any OSS-compatible mixer programs. - Controls available are Master (L&R), Line in (L&R), CD (L&R), + - Control of the ALS-007 mixer via any OSS-compatible mixer programs. + Controls available are Master (L&R), Line in (L&R), CD (L&R), DSP/PCM/audio out (L&R), FM (L&R) and Mic in (mono). Jonathan Woithe -- 1.7.1.251.gf80a2

1 13

[alsa-devel] snd_intel_hda : broken microphone
by mutenmaster＠tiscali.it 23 May '10

23 May '10

hello people, i am really determined in letting you know, for the third time, that my front mic input does not work. i do not know if the rear one works, i suspect not, but it's not important, because before the following commit, the front mic input worked: $ sudo git bisect bad f5271101faf1655d862849f42518c2a88ef394fb is the first bad commit commit f5271101faf1655d862849f42518c2a88ef394fb Author: Lydia Wang <lydiawang(a)viatech.com.cn> Date: Sat Oct 10 19:07: 35 2009 +0800 ALSA HDA VIA: Add VIA_CTL_WIDGET_ANALOG_MUTE control type Enter low power state if AA-Path volume is muted. Signed-off-by: Lydia Wang <lydiawang(a)viatech.com.cn> Signed-off-by: Logan Li <loganli(a)viatech.com.cn> Signed-off-by: Takashi Iwai <tiwai@suse. de> :040000 040000 ab1ae14ff67f0b08848faeb3ad68def7f3e727f0 0bfbfde11fe32e87e8edbdb3c4d03c2d30370393 M sound i'm copypasting the lspci ouput, so that you can have a general idea of what kind of machine i have. please let me know if there is any other info you need to solve this bug. more details on the problem: doing $ arecord -f cd test.wav produces a file of 44 bytes. it's as if no microphone is attached to the jack. this behaviour has been evolving from the commit i showed you forth. at the beginning, a file with actual data was produced, but no audio came out of the speakers when reproducing it. going on with the commits, the file became 44 bytes long. yours, vasilis -- $ lspci -vvv 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge Alternate Subsystem: ASUSTeK Computer Inc. Device 83a2 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: [c4] HyperTransport: Slave or Primary Interface Command: BaseUnitID=0 UnitCnt=12 MastHost- DefDir- DUL- Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn+ LSEn- ExtCTL- 64b- Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- Revision ID: 3.00 Link Frequency 0: [b] Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- Link Frequency 1: 200MHz Link Error 1: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- Prefetchable memory behind bridge Upper: 00-00 Bus Number: 00 Capabilities: [54] HyperTransport: UnitID Clumping Capabilities: [40] HyperTransport: Retry Mode Capabilities: [9c] HyperTransport: #1a Capabilities: [f8] HyperTransport: #1c 00:02.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fea00000-feafffff Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME- Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep+ BwNot+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- Slot # 2, PowerLimit 75.000000; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Not Supported, TimeoutDis- ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -3.5dB Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Count=1/1 Enable+ Address: fee0f00c Data: 4159 Capabilities: [b0] Subsystem: ASUSTeK Computer Inc. Device 83a2 Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Capabilities: [100] Vendor Specific Information <?> Capabilities: [110] Virtual Channel <?> Kernel driver in use: pcieport-driver 00:0a.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 5) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: feb00000-febfffff Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME- Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep+ BwNot+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- Slot # a, PowerLimit 25.000000; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Not Supported, TimeoutDis- ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Count=1/1 Enable+ Address: fee0f00c Data: 4161 Capabilities: [b0] Subsystem: ASUSTeK Computer Inc. Device 83a2 Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Capabilities: [100] Vendor Specific Information <?> Capabilities: [110] Virtual Channel <?> Kernel driver in use: pcieport-driver 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] (prog-if 01 [AHCI 1.0]) Subsystem: ASUSTeK Computer Inc. Device 8389 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 22 Region 0: I/O ports at c000 [size=8] Region 1: I/O ports at b000 [size=4] Region 2: I/O ports at a000 [size=8] Region 3: I/O ports at 9000 [size=4] Region 4: I/O ports at 8000 [size=16] Region 5: Memory at fe9ffc00 (32-bit, non-prefetchable) [size=1K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] SATA HBA <?> Kernel driver in use: ahci 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Device 8389 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fe9fe000 (32-bit, non- prefetchable) [size=4K] Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Device 8389 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fe9fd000 (32-bit, non- prefetchable) [size=4K] Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller (prog-if 20 [EHCI]) Subsystem: ASUSTeK Computer Inc. Device 8389 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 17 Region 0: Memory at fe9ff800 (32- bit, non-prefetchable) [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+, D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [e4] Debug port: BAR=1 offset=00e0 Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller (prog- if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Device 8389 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at fe9fc000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Device 8389 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at fe9fb000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller (prog- if 20 [EHCI]) Subsystem: ASUSTeK Computer Inc. Device 8389 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 19 Region 0: Memory at fe9ff400 (32-bit, non-prefetchable) [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME- Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [e4] Debug port: BAR=1 offset=00e0 Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3c) Subsystem: ASUSTeK Computer Inc. Device 8389 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort- >SERR- <PERR- INTx- Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+ 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller (prog-if 8a [Master SecP PriP]) Subsystem: ASUSTeK Computer Inc. Device 8389 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at ff00 [size=16] Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Count=1/1 Enable- Address: 00000000 Data: 0000 Kernel driver in use: pata_atiixp 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) Subsystem: ASUSTeK Computer Inc. Device 836c Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin ? routed to IRQ 16 Region 0: Memory at fe9f4000 (64-bit, non- prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+, D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller Subsystem: ASUSTeK Computer Inc. Device 8389 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (prog-if 01 [Subtractive decode]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Bus: primary=00, secondary=03, subordinate=03, sec- latency=64 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: fff00000-000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Device 8389 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin C routed to IRQ 18 Region 0: Memory at fe9fa000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] HyperTransport Configuration Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [80] HyperTransport: Host or Secondary Interface Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn+ LSEn+ ExtCTL- 64b- Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Revision ID: 3.00 Link Frequency: [b] Link Error: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE- 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Address Map Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] DRAM Controller Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Kernel modules: amd64_edac_mod 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Miscellaneous Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [f0] Secure device <?> 00: 18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Link Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 01:00.0 VGA compatible controller: ATI Technologies Inc Device 954f (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. Device 02a8 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 2: Memory at feaf0000 (64-bit, non-prefetchable) [size=64K] Region 4: I/O ports at d000 [size=256] Expansion ROM at feac0000 [disabled] [size=128K] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME- Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Count=1/1 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [100] Vendor Specific Information <?> 01:00.1 Audio device: ATI Technologies Inc Device aa38 Subsystem: ASUSTeK Computer Inc. Device aa38 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 28 Region 0: Memory at feaec000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LnkCtl2: Target Link Speed: 2.5 GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De- emphasis Level: -6dB Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Count=1/1 Enable+ Address: 00000000fee0f00c Data: 4189 Capabilities: [100] Vendor Specific Information <?> Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) Subsystem: ASUSTeK Computer Inc. Device 83a3 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 27 Region 0: I/O ports at e800 [size=256] Region 2: Memory at fdfff000 (64-bit, prefetchable) [size=4K] Region 4: Memory at fdff8000 (64-bit, prefetchable) [size=16K] Expansion ROM at febf0000 [disabled] [size=64K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+, D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Count=1/1 Enable+ Address: 00000000fee0f00c Data: 4179 Capabilities: [70] Express (v2) Endpoint, MSI 01 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 4096 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us ClockPM+ Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB Capabilities: [ac] MSI-X: Enable- Mask- TabSize=4 Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00000800 Capabilities: [cc] Vital Product Data <?> Capabilities: [100] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSVoil- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSVoil- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSVoil- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [140] Virtual Channel <?> Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00 Kernel driver in use: r8169 Risparmia con Tutto Incluso Light: telefono + adsl 8 mega a soli 14,95 € al mese. Gratis la Sim Tiscali Mobile con 25 euro di traffico! L'offerta è valida solo se attivi entro il 20/05/10 http://abbonati.tiscali.it/telefono-adsl/prodotti/tc/tuttoincluso_light/?WT…

2 1

Re: [alsa-devel] [PATCH] ALSA: hda: Use LPIB for Toshiba A100-259
by Daniel Chen 22 May '10

22 May '10

(Sorry for top posting due to MUA) Convention is to sort ascending; 0x1106 proceeds 0x1043. On May 22, 2010 3:27 PM, "Paul Menzel" <paulepanter(a)users.sourceforge.net> wrote: Dear Daniel, Am Samstag, den 22.05.2010, 13:25 -0400 schrieb Daniel Chen: […] > - SND_PCI_QUIRK(0x1106, 0x3288, "ASUS M2V-MX SE", POS_FIX_LPIB), > SND_PCI_QUIRK(0x1043, 0x813d, "ASUS P5AD2", POS_FIX_LPIB), > + SND_PCI_QUIRK(0x1106, 0x3288, "ASUS M2V-MX SE", POS_FIX_LPIB), > + SND_PCI_QUIRK(0x1179, 0xff10, "Toshiba A100-259", POS_FIX_LPIB), Is not »m« before »p« in the alphabet? Thanks, Paul _______________________________________________ Alsa-devel mailing list Alsa-devel(a)alsa-project.org http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

1 0

[PATCH] ASoC: Update Freescale i.MX SSI driver DMA parameter handling
by Stuart Longland 22 May '10

22 May '10

This updates the i.MX SSI driver to make it compatible with the ASoC tree following the move of DMA parameters from the DAI to the audio substream object. Signed-off-by: Stuart Longland <redhatter(a)gentoo.org> --- sound/soc/imx/imx-pcm-dma-mx2.c | 7 ++++--- 1 files changed, 4 insertions(+), 3 deletions(-) diff --git a/sound/soc/imx/imx-pcm-dma-mx2.c b/sound/soc/imx/imx-pcm-dma-mx2.c index 2b31ac6..05f19c9 100644 --- a/sound/soc/imx/imx-pcm-dma-mx2.c +++ b/sound/soc/imx/imx-pcm-dma-mx2.c @@ -73,7 +73,8 @@ static void snd_imx_dma_err_callback(int channel, void *data, int err) { struct snd_pcm_substream *substream = data; struct snd_soc_pcm_runtime *rtd = substream->private_data; - struct imx_pcm_dma_params *dma_params = rtd->dai->cpu_dai->dma_data; + struct imx_pcm_dma_params *dma_params = + snd_soc_dai_get_dma_data(rtd->dai->cpu_dai, substream); struct snd_pcm_runtime *runtime = substream->runtime; struct imx_pcm_runtime_data *iprtd = runtime->private_data; int ret; @@ -102,7 +103,7 @@ static int imx_ssi_dma_alloc(struct snd_pcm_substream *substream) struct imx_pcm_runtime_data *iprtd = runtime->private_data; int ret; - dma_params = snd_soc_get_dma_data(rtd->dai->cpu_dai, substream); + dma_params = snd_soc_dai_get_dma_data(rtd->dai->cpu_dai, substream); iprtd->dma = imx_dma_request_by_prio(DRV_NAME, DMA_PRIO_HIGH); if (iprtd->dma < 0) { @@ -212,7 +213,7 @@ static int snd_imx_pcm_prepare(struct snd_pcm_substream *substream) struct imx_pcm_runtime_data *iprtd = runtime->private_data; int err; - dma_params = snd_soc_get_dma_data(rtd->dai->cpu_dai, substream); + dma_params = snd_soc_dai_get_dma_data(rtd->dai->cpu_dai, substream); iprtd->substream = substream; iprtd->buf = (unsigned int *)substream->dma_buffer.area; -- 1.6.4 --2fHTh5uZTiUOsy+g--

1 0

[alsa-devel] [PATCH] ad193x: add set_sysclk entry to support different clock input
by Barry Song 21 May '10

21 May '10

Signed-off-by: Barry Song <21cnbao(a)gmail.com> --- sound/soc/codecs/ad193x.c | 41 ++++++++++++++++++++++++++++++++++++++++- sound/soc/codecs/ad193x.h | 5 +++++ 2 files changed, 45 insertions(+), 1 deletions(-) diff --git a/sound/soc/codecs/ad193x.c b/sound/soc/codecs/ad193x.c index c8ca114..1def75e 100644 --- a/sound/soc/codecs/ad193x.c +++ b/sound/soc/codecs/ad193x.c @@ -24,6 +24,7 @@ /* codec private data */ struct ad193x_priv { + unsigned int sysclk; struct snd_soc_codec codec; u8 reg_cache[AD193X_NUM_REGS]; }; @@ -251,15 +252,32 @@ static int ad193x_set_dai_fmt(struct snd_soc_dai *codec_dai, return 0; } +static int ad193x_set_dai_sysclk(struct snd_soc_dai *codec_dai, + int clk_id, unsigned int freq, int dir) +{ + struct snd_soc_codec *codec = codec_dai->codec; + struct ad193x_priv *ad193x = snd_soc_codec_get_drvdata(codec); + switch (freq) { + case 12288000: + case 18432000: + case 24576000: + case 36864000: + ad193x->sysclk = freq; + return 0; + } + return -EINVAL; +} + static int ad193x_hw_params(struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params, struct snd_soc_dai *dai) { - int word_len = 0, reg = 0; + int word_len = 0, reg = 0, master_rate = 0; struct snd_soc_pcm_runtime *rtd = substream->private_data; struct snd_soc_device *socdev = rtd->socdev; struct snd_soc_codec *codec = socdev->card->codec; + struct ad193x_priv *ad193x = snd_soc_codec_get_drvdata(codec); /* bit size */ switch (params_format(params)) { @@ -275,6 +293,25 @@ static int ad193x_hw_params(struct snd_pcm_substream *substream, break; } + switch (ad193x->sysclk) { + case 12288000: + master_rate = AD193X_PLL_INPUT_256; + break; + case 18432000: + master_rate = AD193X_PLL_INPUT_384; + break; + case 24576000: + master_rate = AD193X_PLL_INPUT_512; + break; + case 36864000: + master_rate = AD193X_PLL_INPUT_768; + break; + } + + reg = snd_soc_read(codec, AD193X_PLL_CLK_CTRL0); + reg = (reg & AD193X_PLL_INPUT_MASK) | master_rate; + snd_soc_write(codec, AD193X_PLL_CLK_CTRL0, reg); + reg = snd_soc_read(codec, AD193X_DAC_CTRL2); reg = (reg & (~AD193X_DAC_WORD_LEN_MASK)) | word_len; snd_soc_write(codec, AD193X_DAC_CTRL2, reg); @@ -348,6 +385,7 @@ static int ad193x_bus_probe(struct device *dev, void *ctrl_data, int bus_type) /* pll input: mclki/xi */ snd_soc_write(codec, AD193X_PLL_CLK_CTRL0, 0x99); /* mclk=24.576Mhz: 0x9D; mclk=12.288Mhz: 0x99 */ snd_soc_write(codec, AD193X_PLL_CLK_CTRL1, 0x04); + ad193x->sysclk = 12288000; ret = snd_soc_register_codec(codec); if (ret != 0) { @@ -383,6 +421,7 @@ static struct snd_soc_dai_ops ad193x_dai_ops = { .hw_params = ad193x_hw_params, .digital_mute = ad193x_mute, .set_tdm_slot = ad193x_set_tdm_slot, + .set_sysclk = ad193x_set_dai_sysclk, .set_fmt = ad193x_set_dai_fmt, }; diff --git a/sound/soc/codecs/ad193x.h b/sound/soc/codecs/ad193x.h index a03c880..654ba64 100644 --- a/sound/soc/codecs/ad193x.h +++ b/sound/soc/codecs/ad193x.h @@ -11,6 +11,11 @@ #define AD193X_PLL_CLK_CTRL0 0x800 #define AD193X_PLL_POWERDOWN 0x01 +#define AD193X_PLL_INPUT_MASK (~0x6) +#define AD193X_PLL_INPUT_256 (0 << 1) +#define AD193X_PLL_INPUT_384 (1 << 1) +#define AD193X_PLL_INPUT_512 (2 << 1) +#define AD193X_PLL_INPUT_768 (3 << 1) #define AD193X_PLL_CLK_CTRL1 0x801 #define AD193X_DAC_CTRL0 0x802 #define AD193X_DAC_POWERDOWN 0x01 -- 1.5.6.3

3 2

[alsa-devel] [PATCH 0/2] Correct widget and PLL handling
by Jorge Eduardo Candelaria 21 May '10

21 May '10

Fix an issue when using 19.2 Mhz as clock input for TWL6040. Also, Drivers in TWL6040 can be modeled after PGA components of DAPM. This allows for better power management and also ensures that the DACs are enabled before the Drivers, reducing this way a pop-noise heard when powering up components.

3 5

[alsa-devel] [ice1712] Word Clock with Delta1010 E
by Bernhard Walle 21 May '10

21 May '10

Hi, we have a problem with the word clock input of the Delta 1010 E. At first: I modified the source code of envy24control to accept the Delta 1010 E as subdevice so that it allows to set the word clock. I'll post the patch after it works with the driver. However, the problem also exists when I use plain alsamixer or amixer. With the unmodified driver, I'm able to turn word clock on but whenever I record something, the arecord program (or Audacity) doesn't get any samples. With OSS (which we're using now but we're trying to switch to ALSA) my colleague Markus Prosch made a patch with lots of try & error that made the word clock working: http://opensound.hg.sourceforge.net/hgweb/opensound/opensound/rev/6a4bad6e7… When I try to "port" that patch to ALSA, the behaviour changes: The recording works, but the sample rate is too low so that it sounds quite strange. In any case: In the same hardware setup, it works flawlessly with OSS. Also, we had no problem with the older Delta 1010. It seems to be an incompatible change (or bug ;)) in revision E. Are there any devs here that know the hardware better and could help me in debugging that issue? Without any deeper sound driver knowledge and without any data sheet, that's quite hard for me. Thanks for your help! Regards, Bernhard PS: Please keep me in Cc since I'm not on the list.

2 2