November 2008 - Alsa-devel - mailman.alsa-project.org

[alsa-devel] Issues with Fujitsu Siemens Amilo PA 1510 laptop
by Travis Place 04 Nov '08

04 Nov '08

2 1

Re: [alsa-devel] [PATCH 1/3] saa7146: Emagic Audiowerk8 low-level ALSA driver
by matthias.nyffenegger＠bluewin.ch 04 Nov '08

04 Nov '08

Hi Takashi, I fixed all of your findings except for the following where i have some questions: >> +/** >> + * >> + * PCI specific stuff >> + * >> + */ >> + >> +/** >> + * Organisation of EEPROM of the SAA7146A: >> + * The data of the subsystem ID and the subsystem vendor ID is organized in >> + * the EEPROM in the following order: >> + * >> + * EE-Addr Value Configuration Space Addr. >> + * --------------------------------------------------------------------- >> + * 00 Subsys ID (high byte) 2C, bits: 31 - 24 >> + * 01 Subsys ID (low byte) 2C, bits: 23 - 16 >> + * 02 Subsys Vendor ID (high byte) 2C, bits: 15 - 8 >> + * 03 Subsys Vendor ID (low byte) 2C, bits: 7 - 0 >> + * 04 Max_Lat 3C, bits: 31 - 24 >> + * 05 Min_Gnt 3C, bits: 23 - 16 >> + * >> + * For AW8 Subsys ID and Subsys Vendor ID are 0xFF on my card. >> + * For AW2 Subsys ID and Subsys Vendor ID are 0x00 on my card. >> + */ >> + >> +static struct pci_device_id snd_aw_ids[] = { >> + { PCI_VENDOR_ID_PHILIPS, PCI_DEVICE_ID_PHILIPS_SAA7146, >> + PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, > >We have a bad problem here. >As mentioned, there are other drivers with the very same device >and the very same PCI ID. >Since your driver doesn't check the availability of the hardware >in some way at probe, it loads even for a video device. >The same problem is present in the existing snd-aw2 driver, and we >need to find out the solution. Obviously the Audiowerk Soundcards cannot reliably be recognized by simply looking at the Subsystem-IDs because they're not unique values. I can see a chance here to probe i2c-bus for onboard EEPROM (AW2 and AW8) and/or onboard PLL (AW8) but I'm not sure whether or not this actually solves the problem for good. Another approach I see is that e.g. SuSE YaST supports loading a module for a specific pci slot - I don't know whether or not this is common use in other distros as well. How do you think about it? >> +enum states {disabled, enabled}; > >Ditto. This should be really a bool. I used to have more than these two states here and might add new states again in the future: that is why I would rather go for the enum type here. Regards, Matthias

1 0

[alsa-devel] [PATCH] hda: make a STAC_DELL_EQ option
by Matthew Ranostay 03 Nov '08

03 Nov '08

Add support for explicitly enabling the EQ distortion hack for systems without software biquad support. Signed-off-by: Matthew Ranostay <mranostay(a)embeddedalley.com> --- diff --git a/pci/hda/patch_sigmatel.c b/pci/hda/patch_sigmatel.c index c2f900f..2c0f37f 100644 --- a/pci/hda/patch_sigmatel.c +++ b/pci/hda/patch_sigmatel.c @@ -70,6 +70,7 @@ enum { enum { STAC_92HD73XX_REF, STAC_DELL_M6, + STAC_DELL_EQ, STAC_92HD73XX_MODELS }; @@ -792,9 +793,7 @@ static struct hda_verb dell_eq_core_init[] = { }; static struct hda_verb dell_m6_core_init[] = { - /* set master volume to max value without distortion - * and direct control */ - { 0x1f, AC_VERB_SET_VOLUME_KNOB_CONTROL, 0xec}, + { 0x1f, AC_VERB_SET_VOLUME_KNOB_CONTROL, 0xff}, /* setup audio connections */ { 0x0d, AC_VERB_SET_CONNECT_SEL, 0x00}, { 0x0a, AC_VERB_SET_CONNECT_SEL, 0x01}, @@ -1622,11 +1621,13 @@ static unsigned int dell_m6_pin_configs[13] = { static unsigned int *stac92hd73xx_brd_tbl[STAC_92HD73XX_MODELS] = { [STAC_92HD73XX_REF] = ref92hd73xx_pin_configs, [STAC_DELL_M6] = dell_m6_pin_configs, + [STAC_DELL_EQ] = dell_m6_pin_configs, }; static const char *stac92hd73xx_models[STAC_92HD73XX_MODELS] = { [STAC_92HD73XX_REF] = "ref", [STAC_DELL_M6] = "dell-m6", + [STAC_DELL_EQ] = "dell-eq", }; static struct snd_pci_quirk stac92hd73xx_cfg_tbl[] = { @@ -4274,12 +4275,17 @@ again: sizeof(stac92hd73xx_dmux)); switch (spec->board_config) { - case STAC_DELL_M6: + case STAC_DELL_EQ: spec->init = dell_eq_core_init; + /* fallthru */ + case STAC_DELL_M6: spec->num_smuxes = 0; spec->mixer = &stac92hd73xx_6ch_mixer[DELL_M6_MIXER]; spec->amp_nids = &stac92hd73xx_amp_nids[DELL_M6_AMP]; spec->num_amps = 1; + + if (!spec->init) + spec->init = dell_m6_core_init; switch (codec->subsystem_id) { case 0x1028025e: /* Analog Mics */ case 0x1028025f: @@ -4289,8 +4295,6 @@ again: break; case 0x10280271: /* Digital Mics */ case 0x10280272: - spec->init = dell_m6_core_init; - /* fall-through */ case 0x10280254: case 0x10280255: stac92xx_set_config_reg(codec, 0x13, 0x90A60160);

2 3

[alsa-devel] Driver: EMU USB 0404 driver development
by Klaus Schulz 03 Nov '08

03 Nov '08

Hi folks. I learned that EMU handed over specs related to the EMU 0202/0404 USB to you guys some time ago. http://ubuntuforums.org/showpost.php?p=4892734&postcount=157 Is anybody assigned to the task? Cheers

4 8

[alsa-devel] ICE1724 / Revolution 7.1 recognized but no sound
by Andreas Hartmetz 03 Nov '08

03 Nov '08

Hi guys, [this is a slightly modified resend of a message to LKML] I have a problem with my sound card. It is the only regular PCI device in my system. alsamixer works fine but any application trying to play sound will either hang when trying to play the first sample (mplayer, aplay) or report an error (amarok with xine backend). mplayer, for example, hangs in an endless loop of this: nanosleep({0, 10000000}, NULL) = 0 ioctl(5, 0x4122, 0) = 0 ioctl(5, 0x4122, 0) = 0 Hardware: Gigabyte GA-MA78G-DS3H mainboard, AMD 780G chipset 2 GB memory Phenom quad-core CPU in AMD64 mode 2 SATA harddisks 1 PATA cdrom on-board graphics PCI sound card M-Audio Revolution 7.1 (ice1724) Software: Kubuntu 8.10, kernel 2.6.27 Software RAID1 (aka md-raid (?)) [the rest is probably not interesting] When I boot a live CD of the same distro with the same kernel the soundcard works fine (and no, it's not a matter of some process blocking the card). The diff of loaded modules looks like this: - snip - diff -u modlist.live modlist.inst --- modlist.live 2008-10-30 03:32:59.000000000 +0100 +++ modlist.inst 2008-10-30 03:48:38.000000000 +0100 @@ -1,30 +1,34 @@ ac 13448 0 ac97_bus 10368 1 snd_ac97_codec -af_packet 29568 2 -ahci 43148 2 +ahci 43148 4 +async_memcpy 10752 1 raid456 +async_tx 16764 3 raid456,async_xor,async_memcpy +async_xor 12032 1 raid456 ata_generic 14212 0 -aufs 196968 1 battery 21128 0 bitblit 14592 1 fbcon -bluetooth 70820 6 bnep,rfcomm,sco,l2cap +bluetooth 70820 6 rfcomm,bnep,sco,l2cap bnep 23168 2 bridge 64544 0 button 15904 0 cdrom 47784 1 sr_mod container 12288 0 cpufreq_conservative 16392 0 -cpufreq_ondemand 16400 4 +cpufreq_ondemand 16400 0 cpufreq_powersave 10368 0 cpufreq_stats 14468 0 -cpufreq_userspace 12420 0 +cpufreq_userspace 12420 4 crc_t10dif 10240 1 sd_mod +crypto_blkcipher 27780 1 dm_crypt +dm_crypt 22792 0 +dm_mod 72944 1 dm_crypt dock 18464 1 libata ehci_hcd 48908 0 -evdev 20512 7 -exportfs 13568 1 aufs +evdev 20512 3 ext3 150544 1 fan 13576 0 fbcon 51200 0 +fglrx 2082944 28 font 17152 1 fbcon freq_table 13568 3 powernow_k8,cpufreq_stats,cpufreq_ondemand fuse 68288 1 @@ -33,22 +37,23 @@ i2c_piix4 17936 0 iptable_filter 11520 0 ip_tables 28176 1 iptable_filter -isofs 44072 1 +ipv6 314312 18 jbd 66472 1 ext3 joydev 20736 0 -l2cap 33280 6 bnep,rfcomm -libata 200160 4 pata_atiixp,pata_acpi,ata_generic,ahci -loop 26380 2 +l2cap 33280 6 rfcomm,bnep +libata 200160 4 pata_atiixp,pata_acpi,ahci,ata_generic +linear 13440 0 lp 19588 0 mbcache 17924 1 ext3 +md_mod 102948 7 raid10,raid456,raid1,raid0,multipath,linear Module Size Used by -nls_cp437 15232 1 +multipath 16512 0 ohci_hcd 34972 0 output 11776 1 video parport 50096 3 ppdev,parport_pc,lp parport_pc 44200 0 pata_acpi 13568 0 -pata_atiixp 14208 1 +pata_atiixp 14208 0 pci_hotplug 39472 1 shpchp pci_slot 13704 0 pcspkr 11136 0 @@ -56,25 +61,28 @@ ppdev 16904 0 processor 47800 2 powernow_k8,thermal r8169 40196 0 +raid0 15488 0 +raid10 32000 0 +raid1 32640 1 +raid456 139552 0 rfcomm 51104 0 sbs 22288 0 sbshc 14592 1 sbs sco 20612 2 scsi_mod 183160 4 sr_mod,sd_mod,sg,libata -sd_mod 45864 4 +sd_mod 45864 6 sg 45408 0 shpchp 42140 0 -snd 79432 19 snd_hda_intel,snd_ice1724,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_ak4xxx_adda,snd_ak4114,snd_pt2258,snd_pcm,snd_i2c,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device +snd 79432 14 snd_ice1724,snd_ac97_codec,snd_ak4xxx_adda,snd_ak4114,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_pt2258,snd_i2c,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device snd_ac97_codec 133080 1 snd_ice1724 snd_ak4114 19328 1 snd_ice1724 snd_ak4xxx_adda 17792 2 snd_ice1724,snd_ice17xx_ak4xxx -snd_hda_intel 489264 1 snd_i2c 14720 2 snd_ice1724,snd_pt2258 -snd_ice1724 119912 1 +snd_ice1724 119912 0 snd_ice17xx_ak4xxx 12416 1 snd_ice1724 snd_mixer_oss 25088 1 snd_pcm_oss -snd_page_alloc 17680 2 snd_hda_intel,snd_pcm -snd_pcm 99208 5 snd_hda_intel,snd_ice1724,snd_ac97_codec,snd_pcm_oss,snd_ak4114 +snd_page_alloc 17680 1 snd_pcm +snd_pcm 99208 4 snd_ice1724,snd_ac97_codec,snd_ak4114,snd_pcm_oss snd_pcm_oss 52608 0 snd_pt2258 12800 1 snd_ice1724 snd_rawmidi 34176 2 snd_ice1724,snd_seq_midi @@ -87,13 +95,15 @@ snd_timer 34320 2 snd_pcm,snd_seq softcursor 10496 1 bitblit soundcore 16800 1 snd -squashfs 48912 1 -sr_mod 24644 1 +sr_mod 24644 0 stp 11268 1 bridge thermal 27424 0 tileblit 11264 1 fbcon -usbcore 175376 4 usbhid,ehci_hcd,ohci_hcd +tun 20996 0 +usbcore 175376 4 usbhid,ohci_hcd,ehci_hcd usbhid 39776 0 video 28948 0 wmi 15808 0 +xfs 575376 1 +xor 14096 2 raid456,async_xor x_tables 31752 1 ip_tables - snip - Note that fglrx or no fglrx, as well as Intel HDA driver or no HDA driver, don't make any difference for my problem - I tested that. /var/log/syslog (from installed system and live CD) and lspci -vv (only installed system) output are appended for further information. I can test bugfix and diagnostic patches as well. Cheers, Andreas INSTALLED /var/log/syslog: Oct 30 09:59:18 rechenplan syslogd 1.5.0#2ubuntu6: restart. Oct 30 09:59:18 rechenplan kernel: Inspecting /boot/System.map-2.6.27-7-generic Oct 30 09:59:18 rechenplan kernel: Cannot find map file. Oct 30 09:59:18 rechenplan kernel: Loaded 59100 symbols from 107 modules. Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Initializing cgroup subsys cpuset Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Initializing cgroup subsys cpu Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Linux version 2.6.27-7-generic (buildd@yellow) (gcc version 4.3.2 (Ubuntu 4.3.2-1ubuntu10) ) #1 SMP Fri Oct 24 06:40:41 UTC 2008 (Ubuntu 2.6.27-7.14-generic) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Command line: root=/dev/md0 ro Oct 30 09:59:18 rechenplan kernel: [ 0.000000] KERNEL supported cpus: Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Intel GenuineIntel Oct 30 09:59:18 rechenplan kernel: [ 0.000000] AMD AuthenticAMD Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Centaur CentaurHauls Oct 30 09:59:18 rechenplan kernel: [ 0.000000] BIOS-provided physical RAM map: Oct 30 09:59:18 rechenplan kernel: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] BIOS-e820: 0000000000100000 - 0000000077de0000 (usable) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] BIOS-e820: 0000000077de0000 - 0000000077de3000 (ACPI NVS) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] BIOS-e820: 0000000077de3000 - 0000000077df0000 (ACPI data) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] BIOS-e820: 0000000077df0000 - 0000000077e00000 (reserved) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] last_pfn = 0x77de0 max_arch_pfn = 0x3ffffffff Oct 30 09:59:18 rechenplan kernel: [ 0.000000] init_memory_mapping Oct 30 09:59:18 rechenplan kernel: [ 0.000000] 0000000000 - 0077c00000 page 2M Oct 30 09:59:18 rechenplan kernel: [ 0.000000] 0077c00000 - 0077de0000 page 4k Oct 30 09:59:18 rechenplan kernel: [ 0.000000] kernel direct mapping tables up to 77de0000 @ 8000-c000 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] last_map_addr: 77de0000 end: 77de0000 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] RAMDISK: 3771b000 - 37fef549 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] DMI 2.4 present. Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: RSDP 000F71C0, 0014 (r0 GBT ) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: RSDT 77DE3000, 0038 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: FACP 77DE3040, 0074 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: DSDT 77DE30C0, 6550 (r1 GBT GBTUACPI 1000 MSFT 3000000) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: FACS 77DE0000, 0040 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: SSDT 77DE9700, 0544 (r1 PTLTD POWERNOW 1 LTP 1) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: HPET 77DE9C80, 0038 (r1 GBT GBTUACPI 42302E31 GBTU 98) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: MCFG 77DE9CC0, 003C (r1 GBT GBTUACPI 42302E31 GBTU 1010101) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: APIC 77DE9640, 0084 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Scanning NUMA topology in Northbridge 24 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] No NUMA configuration found Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Faking a node at 0000000000000000-0000000077de0000 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Bootmem setup node 0 0000000000000000-0000000077de0000 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] NODE_DATA [0000000000001000 - 0000000000005fff] Oct 30 09:59:18 rechenplan kernel: [ 0.000000] bootmap [000000000000a000 - 0000000000018fbf] pages f Oct 30 09:59:18 rechenplan kernel: [ 0.000000] (6 early reservations) ==> bootmem [0000000000 - 0077de0000] Oct 30 09:59:18 rechenplan kernel: [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] Oct 30 09:59:18 rechenplan kernel: [ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] Oct 30 09:59:18 rechenplan kernel: [ 0.000000] #2 [0000200000 - 00008b8f9c] TEXT DATA BSS ==> [0000200000 - 00008b8f9c] Oct 30 09:59:18 rechenplan kernel: [ 0.000000] #3 [003771b000 - 0037fef549] RAMDISK ==> [003771b000 - 0037fef549] Oct 30 09:59:18 rechenplan kernel: [ 0.000000] #4 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000] Oct 30 09:59:18 rechenplan kernel: [ 0.000000] #5 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000] Oct 30 09:59:18 rechenplan kernel: [ 0.000000] found SMP MP-table at [ffff8800000f5840] 000f5840 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] [ffffe20000000000-ffffe20001dfffff] PMD -> [ffff880001200000-ffff880002ffffff] on node 0 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Zone PFN ranges: Oct 30 09:59:18 rechenplan kernel: [ 0.000000] DMA 0x00000000 -> 0x00001000 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] DMA32 0x00001000 -> 0x00100000 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Normal 0x00100000 -> 0x00100000 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Movable zone start PFN for each node Oct 30 09:59:18 rechenplan kernel: [ 0.000000] early_node_map[2] active PFN ranges Oct 30 09:59:18 rechenplan kernel: [ 0.000000] 0: 0x00000000 -> 0x0000009f Oct 30 09:59:18 rechenplan kernel: [ 0.000000] 0: 0x00000100 -> 0x00077de0 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] On node 0 totalpages: 490879 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] DMA zone: 2112 pages, LIFO batch:0 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] DMA32 zone: 479272 pages, LIFO batch:31 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: PM-Timer IO Port: 0x4008 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: Local APIC address 0xfee00000 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1]) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: IRQ0 used by override. Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: IRQ2 used by override. Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: IRQ9 used by override. Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Setting APIC routing to flat Oct 30 09:59:18 rechenplan kernel: [ 0.000000] ACPI: HPET id: 0x10b9a201 base: 0xfed00000 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Using ACPI (MADT) for SMP configuration information Oct 30 09:59:18 rechenplan kernel: [ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs Oct 30 09:59:18 rechenplan kernel: [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Allocating PCI resources starting at 78000000 (gap: 77e00000:68200000) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] PERCPU: Allocating 64928 bytes of per cpu data Oct 30 09:59:18 rechenplan kernel: [ 0.000000] NR_CPUS: 64, nr_cpu_ids: 4, nr_node_ids 1 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 481384 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Policy zone: DMA32 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Kernel command line: root=/dev/md0 ro Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Initializing CPU#0 Oct 30 09:59:18 rechenplan kernel: [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) Oct 30 09:59:18 rechenplan kernel: [ 0.000000] TSC: PIT calibration confirmed by PMTIMER. Oct 30 09:59:18 rechenplan kernel: [ 0.000000] TSC: using PMTIMER calibration value Oct 30 09:59:18 rechenplan kernel: [ 0.000000] Detected 2004.258 MHz processor. Oct 30 09:59:18 rechenplan kernel: [ 0.004000] Console: colour VGA+ 80x25 Oct 30 09:59:18 rechenplan kernel: [ 0.004000] console [tty0] enabled Oct 30 09:59:18 rechenplan kernel: [ 0.004000] Checking aperture... Oct 30 09:59:18 rechenplan kernel: [ 0.004000] No AGP bridge found Oct 30 09:59:18 rechenplan kernel: [ 0.004000] Node 0: aperture @ 5086000000 size 32 MB Oct 30 09:59:18 rechenplan kernel: [ 0.004000] Aperture beyond 4GB. Ignoring. Oct 30 09:59:18 rechenplan kernel: [ 0.004000] Memory: 1916440k/1963904k available (3112k kernel code, 47076k reserved, 1575k data, 536k init) Oct 30 09:59:18 rechenplan kernel: [ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated Oct 30 09:59:18 rechenplan kernel: [ 0.004000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 Oct 30 09:59:18 rechenplan kernel: [ 0.004000] hpet clockevent registered Oct 30 09:59:18 rechenplan kernel: [ 0.004007] Calibrating delay loop (skipped), value calculated using timer frequency.. 4008.51 BogoMIPS (lpj=8017020) Oct 30 09:59:18 rechenplan kernel: [ 0.004092] Security Framework initialized Oct 30 09:59:18 rechenplan kernel: [ 0.004129] SELinux: Disabled at boot. Oct 30 09:59:18 rechenplan kernel: [ 0.004172] AppArmor: AppArmor initialized Oct 30 09:59:18 rechenplan kernel: [ 0.004386] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Oct 30 09:59:18 rechenplan kernel: [ 0.005237] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Oct 30 09:59:18 rechenplan kernel: [ 0.005616] Mount-cache hash table entries: 256 Oct 30 09:59:18 rechenplan kernel: [ 0.005793] Initializing cgroup subsys ns Oct 30 09:59:18 rechenplan kernel: [ 0.005827] Initializing cgroup subsys cpuacct Oct 30 09:59:18 rechenplan kernel: [ 0.005861] Initializing cgroup subsys memory Oct 30 09:59:18 rechenplan kernel: [ 0.005905] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) Oct 30 09:59:18 rechenplan kernel: [ 0.005939] CPU: L2 Cache: 512K (64 bytes/line) Oct 30 09:59:18 rechenplan kernel: [ 0.005973] CPU 0/0 -> Node 0 Oct 30 09:59:18 rechenplan kernel: [ 0.006006] tseg: 0077e00000 Oct 30 09:59:18 rechenplan kernel: [ 0.006008] CPU: Physical Processor ID: 0 Oct 30 09:59:18 rechenplan kernel: [ 0.006040] CPU: Processor Core ID: 0 Oct 30 09:59:18 rechenplan kernel: [ 0.006078] using C1E aware idle routine Oct 30 09:59:18 rechenplan kernel: [ 0.007533] ACPI: Core revision 20080609 Oct 30 09:59:18 rechenplan kernel: [ 0.009676] ACPI: Checking initramfs for custom DSDT Oct 30 09:59:18 rechenplan kernel: [ 0.356633] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 Oct 30 09:59:18 rechenplan kernel: [ 0.397509] CPU0: AMD Phenom(tm) 9350e Quad-Core Processor stepping 03 Oct 30 09:59:18 rechenplan kernel: [ 0.397600] Using local APIC timer interrupts. Oct 30 09:59:18 rechenplan kernel: [ 0.400026] APIC timer calibration result 12526611 Oct 30 09:59:18 rechenplan kernel: [ 0.400028] Detected 12.526 MHz APIC timer. Oct 30 09:59:18 rechenplan kernel: [ 0.400181] Booting processor 1/1 ip 6000 Oct 30 09:59:18 rechenplan kernel: [ 0.004000] Initializing CPU#1 Oct 30 09:59:18 rechenplan kernel: [ 0.004000] Calibrating delay using timer specific routine.. 4008.74 BogoMIPS (lpj=8017489) Oct 30 09:59:18 rechenplan kernel: [ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) Oct 30 09:59:18 rechenplan kernel: [ 0.004000] CPU: L2 Cache: 512K (64 bytes/line) Oct 30 09:59:18 rechenplan kernel: [ 0.004000] CPU 1/1 -> Node 0 Oct 30 09:59:18 rechenplan kernel: [ 0.004000] CPU: Physical Processor ID: 0 Oct 30 09:59:18 rechenplan kernel: [ 0.004000] CPU: Processor Core ID: 2 Oct 30 09:59:18 rechenplan kernel: [ 0.488398] CPU1: AMD Phenom(tm) 9350e Quad-Core Processor stepping 03 Oct 30 09:59:18 rechenplan kernel: [ 0.488713] checking TSC synchronization [CPU#0 -> CPU#1]: passed. Oct 30 09:59:18 rechenplan kernel: [ 0.492108] Booting processor 2/2 ip 6000 Oct 30 09:59:18 rechenplan kernel: [ 0.004000] Initializing CPU#2 Oct 30 09:59:18 rechenplan kernel: [ 0.004000] Calibrating delay using timer specific routine.. 4008.62 BogoMIPS (lpj=8017247) Oct 30 09:59:18 rechenplan kernel: [ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) Oct 30 09:59:18 rechenplan kernel: [ 0.004000] CPU: L2 Cache: 512K (64 bytes/line) Oct 30 09:59:18 rechenplan kernel: [ 0.004000] CPU 2/2 -> Node 0 Oct 30 09:59:18 rechenplan kernel: [ 0.004000] CPU: Physical Processor ID: 0 Oct 30 09:59:18 rechenplan kernel: [ 0.004000] CPU: Processor Core ID: 1 Oct 30 09:59:18 rechenplan kernel: [ 0.580406] CPU2: AMD Phenom(tm) 9350e Quad-Core Processor stepping 03 Oct 30 09:59:18 rechenplan kernel: [ 0.580720] checking TSC synchronization [CPU#0 -> CPU#2]: passed. Oct 30 09:59:18 rechenplan kernel: [ 0.584110] Booting processor 3/3 ip 6000 Oct 30 09:59:18 rechenplan kernel: [ 0.004000] Initializing CPU#3 Oct 30 09:59:18 rechenplan kernel: [ 0.004000] Calibrating delay using timer specific routine.. 4008.63 BogoMIPS (lpj=8017277) Oct 30 09:59:18 rechenplan kernel: [ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) Oct 30 09:59:18 rechenplan kernel: [ 0.004000] CPU: L2 Cache: 512K (64 bytes/line) Oct 30 09:59:18 rechenplan kernel: [ 0.004000] CPU 3/3 -> Node 0 Oct 30 09:59:18 rechenplan kernel: [ 0.004000] CPU: Physical Processor ID: 0 Oct 30 09:59:18 rechenplan kernel: [ 0.004000] CPU: Processor Core ID: 3 Oct 30 09:59:18 rechenplan kernel: [ 0.672418] CPU3: AMD Phenom(tm) 9350e Quad-Core Processor stepping 03 Oct 30 09:59:18 rechenplan kernel: [ 0.672733] checking TSC synchronization [CPU#0 -> CPU#3]: passed. Oct 30 09:59:18 rechenplan kernel: [ 0.676054] Brought up 4 CPUs Oct 30 09:59:18 rechenplan kernel: [ 0.676087] Total of 4 processors activated (16034.51 BogoMIPS). Oct 30 09:59:18 rechenplan kernel: [ 0.676207] CPU0 attaching sched-domain: Oct 30 09:59:18 rechenplan kernel: [ 0.676209] domain 0: span 0-3 level CPU Oct 30 09:59:18 rechenplan kernel: [ 0.676211] groups: 0 1 2 3 Oct 30 09:59:18 rechenplan kernel: [ 0.676216] domain 1: span 0-3 level NODE Oct 30 09:59:18 rechenplan kernel: [ 0.676218] groups: 0-3 Oct 30 09:59:18 rechenplan kernel: [ 0.676222] CPU1 attaching sched-domain: Oct 30 09:59:18 rechenplan kernel: [ 0.676224] domain 0: span 0-3 level CPU Oct 30 09:59:18 rechenplan kernel: [ 0.676225] groups: 1 2 3 0 Oct 30 09:59:18 rechenplan kernel: [ 0.676229] domain 1: span 0-3 level NODE Oct 30 09:59:18 rechenplan kernel: [ 0.676231] groups: 0-3 Oct 30 09:59:18 rechenplan kernel: [ 0.676234] CPU2 attaching sched-domain: Oct 30 09:59:18 rechenplan kernel: [ 0.676235] domain 0: span 0-3 level CPU Oct 30 09:59:18 rechenplan kernel: [ 0.676237] groups: 2 3 0 1 Oct 30 09:59:18 rechenplan kernel: [ 0.676240] domain 1: span 0-3 level NODE Oct 30 09:59:18 rechenplan kernel: [ 0.676241] groups: 0-3 Oct 30 09:59:18 rechenplan kernel: [ 0.676244] CPU3 attaching sched-domain: Oct 30 09:59:18 rechenplan kernel: [ 0.676246] domain 0: span 0-3 level CPU Oct 30 09:59:18 rechenplan kernel: [ 0.676247] groups: 3 0 1 2 Oct 30 09:59:18 rechenplan kernel: [ 0.676250] domain 1: span 0-3 level NODE Oct 30 09:59:18 rechenplan kernel: [ 0.676252] groups: 0-3 Oct 30 09:59:18 rechenplan kernel: [ 0.676376] net_namespace: 1552 bytes Oct 30 09:59:18 rechenplan kernel: [ 0.676376] Booting paravirtualized kernel on bare hardware Oct 30 09:59:18 rechenplan kernel: [ 0.676376] Time: 9:58:44 Date: 10/30/08 Oct 30 09:59:18 rechenplan kernel: [ 0.676425] NET: Registered protocol family 16 Oct 30 09:59:18 rechenplan kernel: [ 0.676475] node 0 link 0: io port [c000, ffff] Oct 30 09:59:18 rechenplan kernel: [ 0.676475] TOM: 0000000080000000 aka 2048M Oct 30 09:59:18 rechenplan kernel: [ 0.676475] Fam 10h mmconf [e0000000, e00fffff] Oct 30 09:59:18 rechenplan kernel: [ 0.676475] node 0 link 0: mmio [a0000, bffff] Oct 30 09:59:18 rechenplan kernel: [ 0.676475] node 0 link 0: mmio [80000000, fe02ffff] ==> [80000000, dfffffff] and [e0100000, fe02ffff] Oct 30 09:59:18 rechenplan kernel: [ 0.676475] node 0 link 0: mmio [e0000000, efffffff] ==> [e0100000, efffffff] Oct 30 09:59:18 rechenplan kernel: [ 0.676475] bus: [00,03] on node 0 link 0 Oct 30 09:59:18 rechenplan kernel: [ 0.676475] bus: 00 index 0 io port: [0, ffff] Oct 30 09:59:18 rechenplan kernel: [ 0.676475] bus: 00 index 1 mmio: [a0000, bffff] Oct 30 09:59:18 rechenplan kernel: [ 0.676475] bus: 00 index 2 mmio: [80000000, dfffffff] Oct 30 09:59:18 rechenplan kernel: [ 0.676475] bus: 00 index 3 mmio: [e0100000, fcffffffff] Oct 30 09:59:18 rechenplan kernel: [ 0.676475] ACPI: bus type pci registered Oct 30 09:59:18 rechenplan kernel: [ 0.676475] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 Oct 30 09:59:18 rechenplan kernel: [ 0.676475] PCI: MCFG area at e0000000 reserved in E820 Oct 30 09:59:18 rechenplan kernel: [ 0.690506] PCI: Using MMCONFIG at e0000000 - efffffff Oct 30 09:59:18 rechenplan kernel: [ 0.690540] PCI: Using configuration type 1 for base access Oct 30 09:59:18 rechenplan kernel: [ 0.692355] ACPI: EC: Look up EC in DSDT Oct 30 09:59:18 rechenplan kernel: [ 0.702136] ACPI: Interpreter enabled Oct 30 09:59:18 rechenplan kernel: [ 0.702175] ACPI: (supports S0 S3 S4 S5) Oct 30 09:59:18 rechenplan kernel: [ 0.702334] ACPI: Using IOAPIC for interrupt routing Oct 30 09:59:18 rechenplan kernel: [ 0.708374] ACPI: PCI Root Bridge [PCI0] (0000:00) Oct 30 09:59:18 rechenplan kernel: [ 0.708374] PCI: 0000:00:00.0 reg 1c 64bit mmio: [e0000000, ffffffff] Oct 30 09:59:18 rechenplan kernel: [ 0.708374] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold Oct 30 09:59:18 rechenplan kernel: [ 0.708374] pci 0000:00:0a.0: PME# disabled Oct 30 09:59:18 rechenplan kernel: [ 0.708374] PCI: 0000:00:11.0 reg 10 io port: [ff00, ff07] Oct 30 09:59:18 rechenplan kernel: [ 0.708374] PCI: 0000:00:11.0 reg 14 io port: [fe00, fe03] Oct 30 09:59:18 rechenplan kernel: [ 0.708374] PCI: 0000:00:11.0 reg 18 io port: [fd00, fd07] Oct 30 09:59:18 rechenplan kernel: [ 0.708374] PCI: 0000:00:11.0 reg 1c io port: [fc00, fc03] Oct 30 09:59:18 rechenplan kernel: [ 0.708374] PCI: 0000:00:11.0 reg 20 io port: [fb00, fb0f] Oct 30 09:59:18 rechenplan kernel: [ 0.708374] PCI: 0000:00:11.0 reg 24 32bit mmio: [fe02f000, fe02f3ff] Oct 30 09:59:18 rechenplan kernel: [ 0.708374] PCI: 0000:00:12.0 reg 10 32bit mmio: [fe02e000, fe02efff] Oct 30 09:59:18 rechenplan kernel: [ 0.708374] PCI: 0000:00:12.1 reg 10 32bit mmio: [fe02d000, fe02dfff] Oct 30 09:59:18 rechenplan kernel: [ 0.708441] PCI: 0000:00:12.2 reg 10 32bit mmio: [fe02c000, fe02c0ff] Oct 30 09:59:18 rechenplan kernel: [ 0.708485] pci 0000:00:12.2: supports D1 Oct 30 09:59:18 rechenplan kernel: [ 0.708487] pci 0000:00:12.2: supports D2 Oct 30 09:59:18 rechenplan kernel: [ 0.708488] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot Oct 30 09:59:18 rechenplan kernel: [ 0.708524] pci 0000:00:12.2: PME# disabled Oct 30 09:59:18 rechenplan kernel: [ 0.708578] PCI: 0000:00:13.0 reg 10 32bit mmio: [fe02b000, fe02bfff] Oct 30 09:59:18 rechenplan kernel: [ 0.708628] PCI: 0000:00:13.1 reg 10 32bit mmio: [fe02a000, fe02afff] Oct 30 09:59:18 rechenplan kernel: [ 0.708700] PCI: 0000:00:13.2 reg 10 32bit mmio: [fe029000, fe0290ff] Oct 30 09:59:18 rechenplan kernel: [ 0.708744] pci 0000:00:13.2: supports D1 Oct 30 09:59:18 rechenplan kernel: [ 0.708746] pci 0000:00:13.2: supports D2 Oct 30 09:59:18 rechenplan kernel: [ 0.708747] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot Oct 30 09:59:18 rechenplan kernel: [ 0.708783] pci 0000:00:13.2: PME# disabled Oct 30 09:59:18 rechenplan kernel: [ 0.708915] PCI: 0000:00:14.1 reg 10 io port: [0, 7] Oct 30 09:59:18 rechenplan kernel: [ 0.708921] PCI: 0000:00:14.1 reg 14 io port: [0, 3] Oct 30 09:59:18 rechenplan kernel: [ 0.708927] PCI: 0000:00:14.1 reg 18 io port: [0, 7] Oct 30 09:59:18 rechenplan kernel: [ 0.708934] PCI: 0000:00:14.1 reg 1c io port: [0, 3] Oct 30 09:59:18 rechenplan kernel: [ 0.708940] PCI: 0000:00:14.1 reg 20 io port: [fa00, fa0f] Oct 30 09:59:18 rechenplan kernel: [ 0.709054] PCI: 0000:00:14.5 reg 10 32bit mmio: [fe028000, fe028fff] Oct 30 09:59:18 rechenplan kernel: [ 0.709185] PCI: 0000:01:05.0 reg 10 32bit mmio: [d8000000, dfffffff] Oct 30 09:59:18 rechenplan kernel: [ 0.709189] PCI: 0000:01:05.0 reg 14 io port: [ee00, eeff] Oct 30 09:59:18 rechenplan kernel: [ 0.709192] PCI: 0000:01:05.0 reg 18 32bit mmio: [fdee0000, fdeeffff] Oct 30 09:59:18 rechenplan kernel: [ 0.709199] PCI: 0000:01:05.0 reg 24 32bit mmio: [fdd00000, fddfffff] Oct 30 09:59:18 rechenplan kernel: [ 0.709208] pci 0000:01:05.0: supports D1 Oct 30 09:59:18 rechenplan kernel: [ 0.709209] pci 0000:01:05.0: supports D2 Oct 30 09:59:18 rechenplan kernel: [ 0.709223] PCI: 0000:01:05.1 reg 10 32bit mmio: [fdefc000, fdefffff] Oct 30 09:59:18 rechenplan kernel: [ 0.709240] pci 0000:01:05.1: supports D1 Oct 30 09:59:18 rechenplan kernel: [ 0.709241] pci 0000:01:05.1: supports D2 Oct 30 09:59:18 rechenplan kernel: [ 0.709278] PCI: bridge 0000:00:01.0 io port: [e000, efff] Oct 30 09:59:18 rechenplan kernel: [ 0.709281] PCI: bridge 0000:00:01.0 32bit mmio: [fdd00000, fdefffff] Oct 30 09:59:18 rechenplan kernel: [ 0.709285] PCI: bridge 0000:00:01.0 64bit mmio pref: [d8000000, dfffffff] Oct 30 09:59:18 rechenplan kernel: [ 0.709317] PCI: 0000:02:00.0 reg 10 io port: [de00, deff] Oct 30 09:59:18 rechenplan kernel: [ 0.709327] PCI: 0000:02:00.0 reg 18 32bit mmio: [fdfff000, fdffffff] Oct 30 09:59:18 rechenplan kernel: [ 0.709338] PCI: 0000:02:00.0 reg 20 32bit mmio: [fdfe0000, fdfeffff] Oct 30 09:59:18 rechenplan kernel: [ 0.709348] PCI: 0000:02:00.0 reg 30 32bit mmio: [0, ffff] Oct 30 09:59:18 rechenplan kernel: [ 0.709369] pci 0000:02:00.0: supports D1 Oct 30 09:59:18 rechenplan kernel: [ 0.709370] pci 0000:02:00.0: supports D2 Oct 30 09:59:18 rechenplan kernel: [ 0.709371] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold Oct 30 09:59:18 rechenplan kernel: [ 0.709407] pci 0000:02:00.0: PME# disabled Oct 30 09:59:18 rechenplan kernel: [ 0.709478] PCI: bridge 0000:00:0a.0 io port: [d000, dfff] Oct 30 09:59:18 rechenplan kernel: [ 0.709481] PCI: bridge 0000:00:0a.0 32bit mmio: [fda00000, fdafffff] Oct 30 09:59:18 rechenplan kernel: [ 0.709484] PCI: bridge 0000:00:0a.0 64bit mmio pref: [fdf00000, fdffffff] Oct 30 09:59:18 rechenplan kernel: [ 0.709535] PCI: 0000:03:07.0 reg 10 io port: [cf00, cf1f] Oct 30 09:59:18 rechenplan kernel: [ 0.709543] PCI: 0000:03:07.0 reg 14 io port: [ce00, ce7f] Oct 30 09:59:18 rechenplan kernel: [ 0.709592] pci 0000:03:07.0: supports D2 Oct 30 09:59:18 rechenplan kernel: [ 0.709630] pci 0000:00:14.4: transparent bridge Oct 30 09:59:18 rechenplan kernel: [ 0.709665] PCI: bridge 0000:00:14.4 io port: [c000, cfff] Oct 30 09:59:18 rechenplan kernel: [ 0.709669] PCI: bridge 0000:00:14.4 32bit mmio: [fdc00000, fdcfffff] Oct 30 09:59:18 rechenplan kernel: [ 0.709673] PCI: bridge 0000:00:14.4 32bit mmio pref: [fdb00000, fdbfffff] Oct 30 09:59:18 rechenplan kernel: [ 0.709689] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] Oct 30 09:59:18 rechenplan kernel: [ 0.710205] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] Oct 30 09:59:18 rechenplan kernel: [ 0.710404] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCEA._PRT] Oct 30 09:59:18 rechenplan kernel: [ 0.710538] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] Oct 30 09:59:18 rechenplan kernel: [ 0.741546] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled. Oct 30 09:59:18 rechenplan kernel: [ 0.741546] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled. Oct 30 09:59:18 rechenplan kernel: [ 0.741546] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled. Oct 30 09:59:18 rechenplan kernel: [ 0.744400] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled. Oct 30 09:59:18 rechenplan kernel: [ 0.744887] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled. Oct 30 09:59:18 rechenplan kernel: [ 0.745380] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled. Oct 30 09:59:18 rechenplan kernel: [ 0.746354] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11) *0, disabled. Oct 30 09:59:18 rechenplan kernel: [ 0.746845] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled. Oct 30 09:59:18 rechenplan kernel: [ 0.747256] Linux Plug and Play Support v0.97 (c) Adam Belay Oct 30 09:59:18 rechenplan kernel: [ 0.747256] pnp: PnP ACPI init Oct 30 09:59:18 rechenplan kernel: [ 0.747256] ACPI: bus type pnp registered Oct 30 09:59:18 rechenplan kernel: [ 0.749043] pnp 00:09: mem resource (0xe0000000-0xefffffff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling Oct 30 09:59:18 rechenplan kernel: [ 0.749043] pnp 00:0a: mem resource (0xffff0000-0xffffffff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling Oct 30 09:59:18 rechenplan kernel: [ 0.749043] pnp 00:0a: mem resource (0xfec00000-0xfec00fff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling Oct 30 09:59:18 rechenplan kernel: [ 0.749043] pnp 00:0a: mem resource (0xfee00000-0xfee00fff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling Oct 30 09:59:18 rechenplan kernel: [ 0.749043] pnp 00:0a: mem resource (0xfff80000-0xfffeffff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling Oct 30 09:59:18 rechenplan kernel: [ 0.749043] pnp: PnP ACPI: found 11 devices Oct 30 09:59:18 rechenplan kernel: [ 0.749043] ACPI: ACPI bus type pnp unregistered Oct 30 09:59:18 rechenplan kernel: [ 0.749043] PCI: Using ACPI for IRQ routing Oct 30 09:59:18 rechenplan kernel: [ 0.749043] pci 0000:00:00.0: BAR 3: can't allocate resource Oct 30 09:59:18 rechenplan kernel: [ 0.768040] NET: Registered protocol family 8 Oct 30 09:59:18 rechenplan kernel: [ 0.768073] NET: Registered protocol family 20 Oct 30 09:59:18 rechenplan kernel: [ 0.768117] NetLabel: Initializing Oct 30 09:59:18 rechenplan kernel: [ 0.768117] NetLabel: domain hash size = 128 Oct 30 09:59:18 rechenplan kernel: [ 0.768117] NetLabel: protocols = UNLABELED CIPSOv4 Oct 30 09:59:18 rechenplan kernel: [ 0.768141] NetLabel: unlabeled traffic allowed by default Oct 30 09:59:18 rechenplan kernel: [ 0.768236] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 Oct 30 09:59:18 rechenplan kernel: [ 0.768310] hpet0: 4 32-bit timers, 14318180 Hz Oct 30 09:59:18 rechenplan kernel: [ 0.772041] Switched to high resolution mode on CPU 0 Oct 30 09:59:18 rechenplan kernel: [ 0.772754] tracer: 1286 pages allocated for 65536 entries of 80 bytes Oct 30 09:59:18 rechenplan kernel: [ 0.772788] actual entries 65586 Oct 30 09:59:18 rechenplan kernel: [ 0.772804] Switched to high resolution mode on CPU 1 Oct 30 09:59:18 rechenplan kernel: [ 0.772812] Switched to high resolution mode on CPU 2 Oct 30 09:59:18 rechenplan kernel: [ 0.772824] Switched to high resolution mode on CPU 3 Oct 30 09:59:18 rechenplan kernel: [ 0.772910] AppArmor: AppArmor Filesystem Enabled Oct 30 09:59:18 rechenplan kernel: [ 0.772961] ACPI: RTC can wake from S4 Oct 30 09:59:18 rechenplan kernel: [ 0.792020] system 00:01: ioport range 0x4d0-0x4d1 has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792055] system 00:01: ioport range 0x220-0x225 has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792089] system 00:01: ioport range 0x290-0x294 has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792125] system 00:02: ioport range 0x4100-0x411f has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792160] system 00:02: ioport range 0x228-0x22f has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792194] system 00:02: ioport range 0x238-0x23f has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792228] system 00:02: ioport range 0x40b-0x40b has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792262] system 00:02: ioport range 0x4d6-0x4d6 has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792296] system 00:02: ioport range 0xc00-0xc01 has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792330] system 00:02: ioport range 0xc14-0xc14 has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792364] system 00:02: ioport range 0xc50-0xc52 has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792398] system 00:02: ioport range 0xc6c-0xc6d has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792432] system 00:02: ioport range 0xc6f-0xc6f has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792466] system 00:02: ioport range 0xcd0-0xcd1 has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792500] system 00:02: ioport range 0xcd2-0xcd3 has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792534] system 00:02: ioport range 0xcd4-0xcdf has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792567] system 00:02: ioport range 0x4000-0x40fe has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792601] system 00:02: ioport range 0x4210-0x4217 has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792636] system 00:02: ioport range 0xb00-0xb0f has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792670] system 00:02: ioport range 0xb10-0xb1f has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792704] system 00:02: ioport range 0xb20-0xb3f has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792751] system 00:0a: iomem range 0xd1a00-0xd3fff has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792785] system 00:0a: iomem range 0xf0000-0xf7fff could not be reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792820] system 00:0a: iomem range 0xf8000-0xfbfff could not be reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792854] system 00:0a: iomem range 0xfc000-0xfffff could not be reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792888] system 00:0a: iomem range 0x77de0000-0x77dfffff could not be reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792925] system 00:0a: iomem range 0x0-0x9ffff could not be reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792959] system 00:0a: iomem range 0x100000-0x77ddffff could not be reserved Oct 30 09:59:18 rechenplan kernel: [ 0.792996] system 00:0a: iomem range 0x77ef0000-0x7feeffff has been reserved Oct 30 09:59:18 rechenplan kernel: [ 0.798143] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 Oct 30 09:59:18 rechenplan kernel: [ 0.798178] pci 0000:00:01.0: IO window: 0xe000-0xefff Oct 30 09:59:18 rechenplan kernel: [ 0.798213] pci 0000:00:01.0: MEM window: 0xfdd00000-0xfdefffff Oct 30 09:59:18 rechenplan kernel: [ 0.798247] pci 0000:00:01.0: PREFETCH window: 0x000000d8000000-0x000000dfffffff Oct 30 09:59:18 rechenplan kernel: [ 0.798287] pci 0000:00:0a.0: PCI bridge, secondary bus 0000:02 Oct 30 09:59:18 rechenplan kernel: [ 0.798321] pci 0000:00:0a.0: IO window: 0xd000-0xdfff Oct 30 09:59:18 rechenplan kernel: [ 0.798355] pci 0000:00:0a.0: MEM window: 0xfda00000-0xfdafffff Oct 30 09:59:18 rechenplan kernel: [ 0.798390] pci 0000:00:0a.0: PREFETCH window: 0x000000fdf00000-0x000000fdffffff Oct 30 09:59:18 rechenplan kernel: [ 0.798428] pci 0000:00:14.4: PCI bridge, secondary bus 0000:03 Oct 30 09:59:18 rechenplan kernel: [ 0.798463] pci 0000:00:14.4: IO window: 0xc000-0xcfff Oct 30 09:59:18 rechenplan kernel: [ 0.798500] pci 0000:00:14.4: MEM window: 0xfdc00000-0xfdcfffff Oct 30 09:59:18 rechenplan kernel: [ 0.798536] pci 0000:00:14.4: PREFETCH window: 0x000000fdb00000-0x000000fdbfffff Oct 30 09:59:18 rechenplan kernel: [ 0.798591] pci 0000:00:0a.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Oct 30 09:59:18 rechenplan kernel: [ 0.798626] pci 0000:00:0a.0: setting latency timer to 64 Oct 30 09:59:18 rechenplan kernel: [ 0.798633] bus: 00 index 0 io port: [0, ffff] Oct 30 09:59:18 rechenplan kernel: [ 0.798666] bus: 00 index 1 mmio: [0, ffffffffffffffff] Oct 30 09:59:18 rechenplan kernel: [ 0.798699] bus: 01 index 0 io port: [e000, efff] Oct 30 09:59:18 rechenplan kernel: [ 0.798732] bus: 01 index 1 mmio: [fdd00000, fdefffff] Oct 30 09:59:18 rechenplan kernel: [ 0.798765] bus: 01 index 2 mmio: [d8000000, dfffffff] Oct 30 09:59:18 rechenplan kernel: [ 0.798798] bus: 01 index 3 mmio: [0, 0] Oct 30 09:59:18 rechenplan kernel: [ 0.798831] bus: 02 index 0 io port: [d000, dfff] Oct 30 09:59:18 rechenplan kernel: [ 0.798863] bus: 02 index 1 mmio: [fda00000, fdafffff] Oct 30 09:59:18 rechenplan kernel: [ 0.798896] bus: 02 index 2 mmio: [fdf00000, fdffffff] Oct 30 09:59:18 rechenplan kernel: [ 0.798930] bus: 02 index 3 mmio: [0, 0] Oct 30 09:59:18 rechenplan kernel: [ 0.798962] bus: 03 index 0 io port: [c000, cfff] Oct 30 09:59:18 rechenplan kernel: [ 0.798995] bus: 03 index 1 mmio: [fdc00000, fdcfffff] Oct 30 09:59:18 rechenplan kernel: [ 0.799028] bus: 03 index 2 mmio: [fdb00000, fdbfffff] Oct 30 09:59:18 rechenplan kernel: [ 0.799061] bus: 03 index 3 io port: [0, ffff] Oct 30 09:59:18 rechenplan kernel: [ 0.799093] bus: 03 index 4 mmio: [0, ffffffffffffffff] Oct 30 09:59:18 rechenplan kernel: [ 0.799136] NET: Registered protocol family 2 Oct 30 09:59:18 rechenplan kernel: [ 0.840125] IP route cache hash table entries: 65536 (order: 7, 524288 bytes) Oct 30 09:59:18 rechenplan kernel: [ 0.840941] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) Oct 30 09:59:18 rechenplan kernel: [ 0.842401] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) Oct 30 09:59:18 rechenplan kernel: [ 0.842771] TCP: Hash tables configured (established 262144 bind 65536) Oct 30 09:59:18 rechenplan kernel: [ 0.842806] TCP reno registered Oct 30 09:59:18 rechenplan kernel: [ 0.852108] NET: Registered protocol family 1 Oct 30 09:59:18 rechenplan kernel: [ 0.852256] checking if image is initramfs... it is Oct 30 09:59:18 rechenplan kernel: [ 1.554403] Freeing initrd memory: 9041k freed Oct 30 09:59:18 rechenplan kernel: [ 1.559325] audit: initializing netlink socket (disabled) Oct 30 09:59:18 rechenplan kernel: [ 1.559371] type=2000 audit(1225360724.556:1): initialized Oct 30 09:59:18 rechenplan kernel: [ 1.564690] HugeTLB registered 2 MB page size, pre-allocated 0 pages Oct 30 09:59:18 rechenplan kernel: [ 1.567424] VFS: Disk quotas dquot_6.5.1 Oct 30 09:59:18 rechenplan kernel: [ 1.567537] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Oct 30 09:59:18 rechenplan kernel: [ 1.567672] msgmni has been set to 3760 Oct 30 09:59:18 rechenplan kernel: [ 1.567832] io scheduler noop registered Oct 30 09:59:18 rechenplan kernel: [ 1.567865] io scheduler anticipatory registered Oct 30 09:59:18 rechenplan kernel: [ 1.567898] io scheduler deadline registered Oct 30 09:59:18 rechenplan kernel: [ 1.568063] io scheduler cfq registered (default) Oct 30 09:59:18 rechenplan kernel: [ 1.708053] pci 0000:01:05.0: Boot video device Oct 30 09:59:18 rechenplan kernel: [ 1.708194] pcieport-driver 0000:00:0a.0: setting latency timer to 64 Oct 30 09:59:18 rechenplan kernel: [ 1.708215] pcieport-driver 0000:00:0a.0: found MSI capability Oct 30 09:59:18 rechenplan kernel: [ 1.708274] pci_express 0000:00:0a.0:pcie00: allocate port service Oct 30 09:59:18 rechenplan kernel: [ 1.744417] hpet_resources: 0xfed00000 is busy Oct 30 09:59:18 rechenplan kernel: [ 1.744487] Linux agpgart interface v0.103 Oct 30 09:59:18 rechenplan kernel: [ 1.744526] Serial: 8250/16550 driver4 ports, IRQ sharing enabled Oct 30 09:59:18 rechenplan kernel: [ 1.746694] brd: module loaded Oct 30 09:59:18 rechenplan kernel: [ 1.746799] input: Macintosh mouse button emulation as /devices/virtual/input/input0 Oct 30 09:59:18 rechenplan kernel: [ 1.746949] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 Oct 30 09:59:18 rechenplan kernel: [ 1.746983] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp Oct 30 09:59:18 rechenplan kernel: [ 1.747146] serio: i8042 KBD port at 0x60,0x64 irq 1 Oct 30 09:59:18 rechenplan kernel: [ 1.760135] mice: PS/2 mouse device common for all mice Oct 30 09:59:18 rechenplan kernel: [ 1.760298] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0 Oct 30 09:59:18 rechenplan kernel: [ 1.760361] rtc0: alarms up to one month, hpet irqs Oct 30 09:59:18 rechenplan kernel: [ 1.760432] cpuidle: using governor ladder Oct 30 09:59:18 rechenplan kernel: [ 1.760466] cpuidle: using governor menu Oct 30 09:59:18 rechenplan kernel: [ 1.760876] TCP cubic registered Oct 30 09:59:18 rechenplan kernel: [ 1.761116] registered taskstats version 1 Oct 30 09:59:18 rechenplan kernel: [ 1.761274] Magic number: 12:674:981 Oct 30 09:59:18 rechenplan kernel: [ 1.761314] tty ttyc8: hash matches Oct 30 09:59:18 rechenplan kernel: [ 1.761445] rtc_cmos 00:05: setting system clock to 2008-10-30 09:58:45 UTC (1225360725) Oct 30 09:59:18 rechenplan kernel: [ 1.761482] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found Oct 30 09:59:18 rechenplan kernel: [ 1.761516] EDD information not available. Oct 30 09:59:18 rechenplan kernel: [ 1.761579] Freeing unused kernel memory: 536k freed Oct 30 09:59:18 rechenplan kernel: [ 1.761807] Write protecting the kernel read-only data: 4348k Oct 30 09:59:18 rechenplan kernel: [ 1.778231] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 Oct 30 09:59:18 rechenplan kernel: [ 1.854573] fuse init (API version 7.9) Oct 30 09:59:18 rechenplan kernel: [ 1.874605] processor ACPI0007:00: registered as cooling_device0 Oct 30 09:59:18 rechenplan kernel: [ 1.874704] processor ACPI0007:01: registered as cooling_device1 Oct 30 09:59:18 rechenplan kernel: [ 1.874796] processor ACPI0007:02: registered as cooling_device2 Oct 30 09:59:18 rechenplan kernel: [ 1.874889] processor ACPI0007:03: registered as cooling_device3 Oct 30 09:59:18 rechenplan kernel: [ 1.892667] md: linear personality registered for level -1 Oct 30 09:59:18 rechenplan kernel: [ 1.896718] md: multipath personality registered for level -4 Oct 30 09:59:18 rechenplan kernel: [ 1.900389] md: raid0 personality registered for level 0 Oct 30 09:59:18 rechenplan kernel: [ 1.905358] md: raid1 personality registered for level 1 Oct 30 09:59:18 rechenplan kernel: [ 1.908731] xor: automatically using best checksumming function: generic_sse Oct 30 09:59:18 rechenplan kernel: [ 1.925004] generic_sse: 8234.000 MB/sec Oct 30 09:59:18 rechenplan kernel: [ 1.925037] xor: using function: generic_sse (8234.000 MB/sec) Oct 30 09:59:18 rechenplan kernel: [ 1.926305] async_tx: api initialized (async) Oct 30 09:59:18 rechenplan kernel: [ 1.997011] raid6: int64x1 2098 MB/s Oct 30 09:59:18 rechenplan kernel: [ 2.065020] raid6: int64x2 2791 MB/s Oct 30 09:59:18 rechenplan kernel: [ 2.133032] raid6: int64x4 2409 MB/s Oct 30 09:59:18 rechenplan kernel: [ 2.201041] raid6: int64x8 1825 MB/s Oct 30 09:59:18 rechenplan kernel: [ 2.269012] raid6: sse2x1 2884 MB/s Oct 30 09:59:18 rechenplan kernel: [ 2.337002] raid6: sse2x2 4736 MB/s Oct 30 09:59:18 rechenplan kernel: [ 2.405005] raid6: sse2x4 5703 MB/s Oct 30 09:59:18 rechenplan kernel: [ 2.405037] raid6: using algorithm sse2x4 (5703 MB/s) Oct 30 09:59:18 rechenplan kernel: [ 2.405072] md: raid6 personality registered for level 6 Oct 30 09:59:18 rechenplan kernel: [ 2.405105] md: raid5 personality registered for level 5 Oct 30 09:59:18 rechenplan kernel: [ 2.405138] md: raid4 personality registered for level 4 Oct 30 09:59:18 rechenplan kernel: [ 2.425850] md: raid10 personality registered for level 10 Oct 30 09:59:18 rechenplan kernel: [ 2.573052] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded Oct 30 09:59:18 rechenplan kernel: [ 2.573108] r8169 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Oct 30 09:59:18 rechenplan kernel: [ 2.573158] r8169 0000:02:00.0: setting latency timer to 64 Oct 30 09:59:18 rechenplan kernel: [ 2.573452] eth0: RTL8168c/8111c at 0xffffc2000032a000, 00:1f:d0:56:5e:a0, XID 3c4000c0 IRQ 2302 Oct 30 09:59:18 rechenplan kernel: [ 2.589619] usbcore: registered new interface driver usbfs Oct 30 09:59:18 rechenplan kernel: [ 2.589907] usbcore: registered new interface driver hub Oct 30 09:59:18 rechenplan kernel: [ 2.589982] usbcore: registered new device driver usb Oct 30 09:59:18 rechenplan kernel: [ 2.591081] No dock devices found. Oct 30 09:59:18 rechenplan kernel: [ 2.592723] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver Oct 30 09:59:18 rechenplan kernel: [ 2.592761] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Oct 30 09:59:18 rechenplan kernel: [ 2.592811] ohci_hcd 0000:00:12.0: OHCI Host Controller Oct 30 09:59:18 rechenplan kernel: [ 2.592890] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 1 Oct 30 09:59:18 rechenplan kernel: [ 2.592958] ohci_hcd 0000:00:12.0: irq 16, io mem 0xfe02e000 Oct 30 09:59:18 rechenplan kernel: [ 2.604234] SCSI subsystem initialized Oct 30 09:59:18 rechenplan kernel: [ 2.623793] libata version 3.00 loaded. Oct 30 09:59:18 rechenplan kernel: [ 2.652185] usb usb1: configuration #1 chosen from 1 choice Oct 30 09:59:18 rechenplan kernel: [ 2.652247] hub 1-0:1.0: USB hub found Oct 30 09:59:18 rechenplan kernel: [ 2.652288] hub 1-0:1.0: 3 ports detected Oct 30 09:59:18 rechenplan kernel: [ 2.860253] ohci_hcd 0000:00:12.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Oct 30 09:59:18 rechenplan kernel: [ 2.860305] ohci_hcd 0000:00:12.1: OHCI Host Controller Oct 30 09:59:18 rechenplan kernel: [ 2.860364] ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 2 Oct 30 09:59:18 rechenplan kernel: [ 2.860417] ohci_hcd 0000:00:12.1: irq 16, io mem 0xfe02d000 Oct 30 09:59:18 rechenplan kernel: [ 2.920193] usb usb2: configuration #1 chosen from 1 choice Oct 30 09:59:18 rechenplan kernel: [ 2.920255] hub 2-0:1.0: USB hub found Oct 30 09:59:18 rechenplan kernel: [ 2.920296] hub 2-0:1.0: 3 ports detected Oct 30 09:59:18 rechenplan kernel: [ 3.000025] usb 1-2: new low speed USB device using ohci_hcd and address 2 Oct 30 09:59:18 rechenplan kernel: [ 3.030352] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Oct 30 09:59:18 rechenplan kernel: [ 3.030402] ohci_hcd 0000:00:13.0: OHCI Host Controller Oct 30 09:59:18 rechenplan kernel: [ 3.030457] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 3 Oct 30 09:59:18 rechenplan kernel: [ 3.030523] ohci_hcd 0000:00:13.0: irq 18, io mem 0xfe02b000 Oct 30 09:59:18 rechenplan kernel: [ 3.088082] usb usb3: configuration #1 chosen from 1 choice Oct 30 09:59:18 rechenplan kernel: [ 3.088138] hub 3-0:1.0: USB hub found Oct 30 09:59:18 rechenplan kernel: [ 3.088177] hub 3-0:1.0: 3 ports detected Oct 30 09:59:18 rechenplan kernel: [ 3.173344] usb 1-2: configuration #1 chosen from 1 choice Oct 30 09:59:18 rechenplan kernel: [ 3.188151] ahci 0000:00:11.0: version 3.0 Oct 30 09:59:18 rechenplan kernel: [ 3.188169] ahci 0000:00:11.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 Oct 30 09:59:18 rechenplan kernel: [ 3.188349] ahci 0000:00:11.0: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode Oct 30 09:59:18 rechenplan kernel: [ 3.188389] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part Oct 30 09:59:18 rechenplan kernel: [ 3.188834] scsi0 : ahci Oct 30 09:59:18 rechenplan kernel: [ 3.188967] scsi1 : ahci Oct 30 09:59:18 rechenplan kernel: [ 3.189056] scsi2 : ahci Oct 30 09:59:18 rechenplan kernel: [ 3.189155] scsi3 : ahci Oct 30 09:59:18 rechenplan kernel: [ 3.189249] scsi4 : ahci Oct 30 09:59:18 rechenplan kernel: [ 3.189348] scsi5 : ahci Oct 30 09:59:18 rechenplan kernel: [ 3.189499] ata1: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 2301 Oct 30 09:59:18 rechenplan kernel: [ 3.189537] ata2: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 2301 Oct 30 09:59:18 rechenplan kernel: [ 3.189575] ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 2301 Oct 30 09:59:18 rechenplan kernel: [ 3.189613] ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 2301 Oct 30 09:59:18 rechenplan kernel: [ 3.189651] ata5: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f300 irq 2301 Oct 30 09:59:18 rechenplan kernel: [ 3.189689] ata6: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f380 irq 2301 Oct 30 09:59:18 rechenplan kernel: [ 3.672022] ata1: softreset failed (device not ready) Oct 30 09:59:18 rechenplan kernel: [ 3.672059] ata1: failed due to HW bug, retry pmp=0 Oct 30 09:59:18 rechenplan kernel: [ 3.836031] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Oct 30 09:59:18 rechenplan kernel: [ 3.842397] ata1.00: ATA-7: SAMSUNG HD642JJ, 1AA01112, max UDMA7 Oct 30 09:59:18 rechenplan kernel: [ 3.842435] ata1.00: 1250263728 sectors, multi 0: LBA48 NCQ (depth 31/32) Oct 30 09:59:18 rechenplan kernel: [ 3.848862] ata1.00: configured for UDMA/133 Oct 30 09:59:18 rechenplan kernel: [ 4.184537] ata2: SATA link down (SStatus 0 SControl 300) Oct 30 09:59:18 rechenplan kernel: [ 4.524032] ata3: SATA link down (SStatus 0 SControl 300) Oct 30 09:59:18 rechenplan kernel: [ 4.860032] ata4: SATA link down (SStatus 0 SControl 300) Oct 30 09:59:18 rechenplan kernel: [ 5.360019] ata5: softreset failed (device not ready) Oct 30 09:59:18 rechenplan kernel: [ 5.360059] ata5: failed due to HW bug, retry pmp=0 Oct 30 09:59:18 rechenplan kernel: [ 5.524031] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Oct 30 09:59:18 rechenplan kernel: [ 5.536698] ata5.00: HPA unlocked: 1250261615 -> 1250263728, native 1250263728 Oct 30 09:59:18 rechenplan kernel: [ 5.536739] ata5.00: ATA-7: SAMSUNG HD642JJ, 1AA01112, max UDMA7 Oct 30 09:59:18 rechenplan kernel: [ 5.536773] ata5.00: 1250263728 sectors, multi 0: LBA48 NCQ (depth 31/32) Oct 30 09:59:18 rechenplan kernel: [ 5.543194] ata5.00: configured for UDMA/133 Oct 30 09:59:18 rechenplan kernel: [ 5.876032] ata6: SATA link down (SStatus 0 SControl 300) Oct 30 09:59:18 rechenplan kernel: [ 5.892616] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD642JJ 1AA0 PQ: 0 ANSI: 5 Oct 30 09:59:18 rechenplan kernel: [ 5.892768] scsi 4:0:0:0: Direct-Access ATA SAMSUNG HD642JJ 1AA0 PQ: 0 ANSI: 5 Oct 30 09:59:18 rechenplan kernel: [ 5.892886] ohci_hcd 0000:00:13.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Oct 30 09:59:18 rechenplan kernel: [ 5.892930] ohci_hcd 0000:00:13.1: OHCI Host Controller Oct 30 09:59:18 rechenplan kernel: [ 5.892986] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 4 Oct 30 09:59:18 rechenplan kernel: [ 5.893036] ohci_hcd 0000:00:13.1: irq 18, io mem 0xfe02a000 Oct 30 09:59:18 rechenplan kernel: [ 5.952099] usb usb4: configuration #1 chosen from 1 choice Oct 30 09:59:18 rechenplan kernel: [ 5.952155] hub 4-0:1.0: USB hub found Oct 30 09:59:18 rechenplan kernel: [ 5.952196] hub 4-0:1.0: 3 ports detected Oct 30 09:59:18 rechenplan kernel: [ 6.161400] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17 Oct 30 09:59:18 rechenplan kernel: [ 6.161447] ehci_hcd 0000:00:12.2: EHCI Host Controller Oct 30 09:59:18 rechenplan kernel: [ 6.161514] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 5 Oct 30 09:59:18 rechenplan kernel: [ 6.161582] ehci_hcd 0000:00:12.2: debug port 1 Oct 30 09:59:18 rechenplan kernel: [ 6.161636] ehci_hcd 0000:00:12.2: irq 17, io mem 0xfe02c000 Oct 30 09:59:18 rechenplan kernel: [ 6.296026] usb 4-3: new low speed USB device using ohci_hcd and address 2 Oct 30 09:59:18 rechenplan kernel: [ 6.308022] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 Oct 30 09:59:18 rechenplan kernel: [ 6.308163] usb usb5: configuration #1 chosen from 1 choice Oct 30 09:59:18 rechenplan kernel: [ 6.308219] hub 5-0:1.0: USB hub found Oct 30 09:59:18 rechenplan kernel: [ 6.308256] hub 5-0:1.0: 6 ports detected Oct 30 09:59:18 rechenplan kernel: [ 6.492870] usb 4-3: configuration #1 chosen from 1 choice Oct 30 09:59:18 rechenplan kernel: [ 6.497194] usb 1-2: USB disconnect, address 2 Oct 30 09:59:18 rechenplan kernel: [ 6.518562] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 Oct 30 09:59:18 rechenplan kernel: [ 6.518605] ehci_hcd 0000:00:13.2: EHCI Host Controller Oct 30 09:59:18 rechenplan kernel: [ 6.518663] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 6 Oct 30 09:59:18 rechenplan kernel: [ 6.518729] ehci_hcd 0000:00:13.2: debug port 1 Oct 30 09:59:18 rechenplan kernel: [ 6.518782] ehci_hcd 0000:00:13.2: irq 19, io mem 0xfe029000 Oct 30 09:59:18 rechenplan kernel: [ 6.529022] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 Oct 30 09:59:18 rechenplan kernel: [ 6.529147] usb usb6: configuration #1 chosen from 1 choice Oct 30 09:59:18 rechenplan kernel: [ 6.529207] hub 6-0:1.0: USB hub found Oct 30 09:59:18 rechenplan kernel: [ 6.529245] hub 6-0:1.0: 6 ports detected Oct 30 09:59:18 rechenplan kernel: [ 6.684049] usb 4-3: USB disconnect, address 2 Oct 30 09:59:18 rechenplan kernel: [ 6.736146] ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Oct 30 09:59:18 rechenplan kernel: [ 6.736190] ohci_hcd 0000:00:14.5: OHCI Host Controller Oct 30 09:59:18 rechenplan kernel: [ 6.736247] ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 7 Oct 30 09:59:18 rechenplan kernel: [ 6.736297] ohci_hcd 0000:00:14.5: irq 18, io mem 0xfe028000 Oct 30 09:59:18 rechenplan kernel: [ 6.796938] usb usb7: configuration #1 chosen from 1 choice Oct 30 09:59:18 rechenplan kernel: [ 6.797747] hub 7-0:1.0: USB hub found Oct 30 09:59:18 rechenplan kernel: [ 6.797788] hub 7-0:1.0: 2 ports detected Oct 30 09:59:18 rechenplan kernel: [ 6.910877] pata_acpi 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Oct 30 09:59:18 rechenplan kernel: [ 6.915107] scsi6 : pata_atiixp Oct 30 09:59:18 rechenplan kernel: [ 6.917366] scsi7 : pata_atiixp Oct 30 09:59:18 rechenplan kernel: [ 6.918629] ata7: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfa00 irq 14 Oct 30 09:59:18 rechenplan kernel: [ 6.918664] ata8: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfa08 irq 15 Oct 30 09:59:18 rechenplan kernel: [ 6.919126] scsi 0:0:0:0: Attached scsi generic sg0 type 0 Oct 30 09:59:18 rechenplan kernel: [ 6.919196] scsi 4:0:0:0: Attached scsi generic sg1 type 0 Oct 30 09:59:18 rechenplan kernel: [ 6.939979] Driver 'sd' needs updating - please use bus_type methods Oct 30 09:59:18 rechenplan kernel: [ 6.940147] sd 0:0:0:0: [sda] 1250263728 512-byte hardware sectors (640135 MB) Oct 30 09:59:18 rechenplan kernel: [ 6.940198] sd 0:0:0:0: [sda] Write Protect is off Oct 30 09:59:18 rechenplan kernel: [ 6.940233] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 Oct 30 09:59:18 rechenplan kernel: [ 6.940255] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Oct 30 09:59:18 rechenplan kernel: [ 6.940348] sd 0:0:0:0: [sda] 1250263728 512-byte hardware sectors (640135 MB) Oct 30 09:59:18 rechenplan kernel: [ 6.940394] sd 0:0:0:0: [sda] Write Protect is off Oct 30 09:59:18 rechenplan kernel: [ 6.940428] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 Oct 30 09:59:18 rechenplan kernel: [ 6.940448] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Oct 30 09:59:18 rechenplan kernel: [ 6.940487] sda: sda1 sda2 Oct 30 09:59:18 rechenplan kernel: [ 6.944710] sd 0:0:0:0: [sda] Attached SCSI disk Oct 30 09:59:18 rechenplan kernel: [ 6.944835] sd 4:0:0:0: [sdb] 1250263728 512-byte hardware sectors (640135 MB) Oct 30 09:59:18 rechenplan kernel: [ 6.944888] sd 4:0:0:0: [sdb] Write Protect is off Oct 30 09:59:18 rechenplan kernel: [ 6.944923] sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00 Oct 30 09:59:18 rechenplan kernel: [ 6.944947] sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Oct 30 09:59:18 rechenplan kernel: [ 6.945035] sd 4:0:0:0: [sdb] 1250263728 512-byte hardware sectors (640135 MB) Oct 30 09:59:18 rechenplan kernel: [ 6.945083] sd 4:0:0:0: [sdb] Write Protect is off Oct 30 09:59:18 rechenplan kernel: [ 6.945117] sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00 Oct 30 09:59:18 rechenplan kernel: [ 6.945140] sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Oct 30 09:59:18 rechenplan kernel: [ 6.945180] sdb: sdb1 sdb2 Oct 30 09:59:18 rechenplan kernel: [ 6.948684] sd 4:0:0:0: [sdb] Attached SCSI disk Oct 30 09:59:18 rechenplan kernel: [ 7.080585] ata7.00: ATAPI: TOSHIBA DVD-ROM SD-M1612, 1004, max UDMA/33 Oct 30 09:59:18 rechenplan kernel: [ 7.096517] ata7.00: configured for UDMA/33 Oct 30 09:59:18 rechenplan kernel: [ 7.132023] usb 1-2: new low speed USB device using ohci_hcd and address 3 Oct 30 09:59:18 rechenplan kernel: [ 7.252103] isa bounce pool size: 16 pages Oct 30 09:59:18 rechenplan kernel: [ 7.257620] scsi 6:0:0:0: CD-ROM TOSHIBA DVD-ROM SD-M1612 1004 PQ: 0 ANSI: 5 Oct 30 09:59:18 rechenplan kernel: [ 7.257797] scsi 6:0:0:0: Attached scsi generic sg2 type 5 Oct 30 09:59:18 rechenplan kernel: [ 7.277127] Driver 'sr' needs updating - please use bus_type methods Oct 30 09:59:18 rechenplan kernel: [ 7.284828] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray Oct 30 09:59:18 rechenplan kernel: [ 7.284868] Uniform CD-ROM driver Revision: 3.20 Oct 30 09:59:18 rechenplan kernel: [ 7.284995] sr 6:0:0:0: Attached scsi CD-ROM sr0 Oct 30 09:59:18 rechenplan kernel: [ 7.303440] usb 1-2: configuration #1 chosen from 1 choice Oct 30 09:59:18 rechenplan kernel: [ 7.377208] md: md0 stopped. Oct 30 09:59:18 rechenplan kernel: [ 7.381827] md: bind<sdb2> Oct 30 09:59:18 rechenplan kernel: [ 7.394854] md: md0 stopped. Oct 30 09:59:18 rechenplan kernel: [ 7.394902] md: unbind<sdb2> Oct 30 09:59:18 rechenplan kernel: [ 7.416197] md: export_rdev(sdb2) Oct 30 09:59:18 rechenplan kernel: [ 7.418654] md: bind<sdb2> Oct 30 09:59:18 rechenplan kernel: [ 7.418821] md: bind<sda2> Oct 30 09:59:18 rechenplan kernel: [ 7.426029] raid1: raid set md0 active with 2 out of 2 mirrors Oct 30 09:59:18 rechenplan kernel: [ 7.568023] usb 4-3: new low speed USB device using ohci_hcd and address 3 Oct 30 09:59:18 rechenplan kernel: [ 7.749242] usb 4-3: configuration #1 chosen from 1 choice Oct 30 09:59:18 rechenplan kernel: [ 7.753653] usbcore: registered new interface driver hiddev Oct 30 09:59:18 rechenplan kernel: [ 7.758570] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:12.0/usb1/1-2/1-2:1.0/input/input2 Oct 30 09:59:18 rechenplan kernel: [ 7.781627] input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:12.0-2 Oct 30 09:59:18 rechenplan kernel: [ 17.796536] /build/buildd/linux-2.6.27/drivers/hid/usbhid/hid-core.c: usb_submit_urb(ctrl) failed Oct 30 09:59:18 rechenplan kernel: [ 17.797076] usbhid: timeout initializing reports Oct 30 09:59:18 rechenplan kernel: [ 17.797169] input: Logitech Logitech Attack 3 as /devices/pci0000:00/0000:00:13.1/usb4/4-3/4-3:1.0/input/input3 Oct 30 09:59:18 rechenplan kernel: [ 17.797274] input,hidraw1: USB HID v1.10 Joystick [Logitech Logitech Attack 3] on usb-0000:00:13.1-3 Oct 30 09:59:18 rechenplan kernel: [ 17.797437] usbcore: registered new interface driver usbhid Oct 30 09:59:18 rechenplan kernel: [ 17.797472] usbhid: v2.6:USB HID core driver Oct 30 09:59:18 rechenplan kernel: [ 17.862660] PM: Starting manual resume from disk Oct 30 09:59:18 rechenplan kernel: [ 17.862696] PM: Resume from partition 8:17 Oct 30 09:59:18 rechenplan kernel: [ 17.862698] PM: Checking hibernation image. Oct 30 09:59:18 rechenplan kernel: [ 17.862817] PM: Resume from disk failed. Oct 30 09:59:18 rechenplan kernel: [ 17.871663] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled Oct 30 09:59:18 rechenplan kernel: [ 17.877140] SGI XFS Quota Management subsystem Oct 30 09:59:18 rechenplan kernel: [ 17.947568] XFS mounting filesystem md0 Oct 30 09:59:18 rechenplan kernel: [ 18.036737] Ending clean XFS mount for filesystem: md0 Oct 30 09:59:18 rechenplan kernel: [ 26.634365] udevd version 124 started Oct 30 09:59:18 rechenplan kernel: [ 27.055605] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4 Oct 30 09:59:18 rechenplan kernel: [ 27.073535] ACPI: Power Button (FF) [PWRF] Oct 30 09:59:18 rechenplan kernel: [ 27.073666] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5 Oct 30 09:59:18 rechenplan kernel: [ 27.105522] ACPI: Power Button (CM) [PWRB] Oct 30 09:59:18 rechenplan kernel: [ 27.170920] ACPI: WMI: Mapper loaded Oct 30 09:59:18 rechenplan kernel: [ 27.256025] ACPI: I/O resource piix4_smbus [0xb00-0xb07] conflicts with ACPI region SOR1 [0xb00-0xb0f] Oct 30 09:59:18 rechenplan kernel: [ 27.256068] ACPI: Device needs an ACPI driver Oct 30 09:59:18 rechenplan kernel: [ 27.256107] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0 Oct 30 09:59:18 rechenplan kernel: [ 27.288376] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 Oct 30 09:59:18 rechenplan kernel: [ 27.302660] shpchp: HPC vendor_id 1022 device_id 9602 ss_vid 0 ss_did 0 Oct 30 09:59:18 rechenplan kernel: [ 27.302702] shpchp: shpc_init: cannot reserve MMIO region Oct 30 09:59:18 rechenplan kernel: [ 27.302776] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 Oct 30 09:59:18 rechenplan kernel: [ 27.310265] input: PC Speaker as /devices/platform/pcspkr/input/input6 Oct 30 09:59:18 rechenplan kernel: [ 27.503835] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. Oct 30 09:59:18 rechenplan kernel: [ 27.524434] [fglrx] Maximum main memory to use for locked dma buffers: 1759 MBytes. Oct 30 09:59:18 rechenplan kernel: [ 27.524538] [fglrx] vendor: 1002 device: 9610 count: 1 Oct 30 09:59:18 rechenplan kernel: [ 27.526761] [fglrx] ioport: bar 1, base 0xee00, size: 0x100 Oct 30 09:59:18 rechenplan kernel: [ 27.526815] pci 0000:01:05.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Oct 30 09:59:18 rechenplan kernel: [ 27.526852] pci 0000:01:05.0: setting latency timer to 64 Oct 30 09:59:18 rechenplan kernel: [ 27.528519] [fglrx] PAT is enabled successfully! Oct 30 09:59:18 rechenplan kernel: [ 27.528591] [fglrx] module loaded - fglrx 8.54.3 [Oct 10 2008] with 1 minors Oct 30 09:59:18 rechenplan kernel: [ 28.279472] ICE1724 0000:03:07.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 Oct 30 09:59:18 rechenplan kernel: [ 29.380356] Adding 979924k swap on /dev/sdb1. Priority:-1 extents:1 across:979924k Oct 30 09:59:18 rechenplan kernel: [ 30.017533] device-mapper: uevent: version 1.0.3 Oct 30 09:59:18 rechenplan kernel: [ 30.018371] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel(a)redhat.com Oct 30 09:59:18 rechenplan kernel: [ 30.807506] kjournald starting. Commit interval 5 seconds Oct 30 09:59:18 rechenplan kernel: [ 30.807728] EXT3 FS on sda1, internal journal Oct 30 09:59:18 rechenplan kernel: [ 30.807734] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 09:59:18 rechenplan kernel: [ 31.531932] type=1505 audit(1225357155.404:2): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4422 Oct 30 09:59:18 rechenplan kernel: [ 31.532103] type=1505 audit(1225357155.407:3): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4422 Oct 30 09:59:18 rechenplan kernel: [ 31.877829] ip_tables: (C) 2000-2006 Netfilter Core Team Oct 30 09:59:18 rechenplan kernel: [ 31.917731] r8169: eth0: link up Oct 30 09:59:18 rechenplan kernel: [ 31.917739] r8169: eth0: link up Oct 30 09:59:18 rechenplan kernel: [ 32.654387] NET: Registered protocol family 10 Oct 30 09:59:18 rechenplan kernel: [ 32.655034] lo: Disabled Privacy Extensions Oct 30 09:59:18 rechenplan kernel: [ 32.974671] warning: `ntpd' uses 32-bit capabilities (legacy support in use) Oct 30 09:59:18 rechenplan kernel: [ 34.203212] powernow-k8: Found 1 AMD Phenom(tm) 9350e Quad-Core Processor processors (4 cpu cores) (version 2.20.00) Oct 30 09:59:18 rechenplan kernel: [ 34.203745] powernow-k8: 0 : pstate 0 (2000 MHz) Oct 30 09:59:18 rechenplan kernel: [ 34.203749] powernow-k8: 1 : pstate 1 (1000 MHz) Oct 30 09:59:18 rechenplan avahi-daemon[5278]: Found user 'avahi' (UID 107) and group 'avahi' (GID 116). Oct 30 09:59:18 rechenplan avahi-daemon[5278]: Successfully dropped root privileges. Oct 30 09:59:18 rechenplan avahi-daemon[5278]: avahi-daemon 0.6.23 starting up. Oct 30 09:59:18 rechenplan avahi-daemon[5278]: Successfully called chroot(). Oct 30 09:59:18 rechenplan avahi-daemon[5278]: Successfully dropped remaining capabilities. Oct 30 09:59:18 rechenplan avahi-daemon[5278]: No service file found in /etc/avahi/services. Oct 30 09:59:18 rechenplan avahi-daemon[5278]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.1.14. Oct 30 09:59:18 rechenplan avahi-daemon[5278]: New relevant interface eth0.IPv4 for mDNS. Oct 30 09:59:18 rechenplan avahi-daemon[5278]: Network interface enumeration completed. Oct 30 09:59:18 rechenplan avahi-daemon[5278]: Registering new address record for fe80::21f:d0ff:fe56:5ea0 on eth0.*. Oct 30 09:59:18 rechenplan avahi-daemon[5278]: Registering new address record for 192.168.1.14 on eth0.IPv4. Oct 30 09:59:18 rechenplan avahi-daemon[5278]: Registering HINFO record with values 'X86_64'/'LINUX'. Oct 30 09:59:19 rechenplan atieventsd[5318]: ATI External Events Daemon started... Oct 30 09:59:19 rechenplan atieventsd[5318]: Event daemon control socket created Oct 30 09:59:19 rechenplan acpid: client connected from 5318[0:0] Oct 30 09:59:19 rechenplan atieventsd[5318]: acpid connection established Oct 30 09:59:19 rechenplan kernel: [ 35.806245] lp: driver loaded but no devices found Oct 30 09:59:19 rechenplan avahi-daemon[5278]: Server startup complete. Host name is rechenplan.local. Local service cookie is 282689542. Oct 30 09:59:19 rechenplan kernel: [ 35.849742] ppdev: user-space parallel port driver Oct 30 09:59:21 rechenplan powernowd: PowerNow Daemon v1.00, (c) 2003-2008 John Clemens Oct 30 09:59:21 rechenplan powernowd: Found 4 scalable units: -- 1 'CPU' per scalable unit Oct 30 09:59:21 rechenplan powernowd: cpu0: 1000Mhz - 2000Mhz (6 steps) Oct 30 09:59:21 rechenplan powernowd: cpu1: 1000Mhz - 2000Mhz (6 steps) Oct 30 09:59:21 rechenplan powernowd: cpu2: 1000Mhz - 2000Mhz (6 steps) Oct 30 09:59:21 rechenplan powernowd: cpu3: 1000Mhz - 2000Mhz (6 steps) Oct 30 09:59:27 rechenplan kernel: [ 43.501520] eth0: no IPv6 routers present Oct 30 09:59:28 rechenplan kernel: [ 44.453547] tun: Universal TUN/TAP device driver, 1.6 Oct 30 09:59:28 rechenplan kernel: [ 44.453560] tun: (C) 1999-2004 Max Krasnyansky <maxk(a)qualcomm.com> Oct 30 09:59:29 rechenplan acpid: client connected from 5891[109:119] Oct 30 09:59:30 rechenplan bluetoothd[5939]: Bluetooth daemon Oct 30 09:59:30 rechenplan kernel: [ 46.216918] Bluetooth: Core ver 2.13 Oct 30 09:59:30 rechenplan kernel: [ 46.218171] NET: Registered protocol family 31 Oct 30 09:59:30 rechenplan kernel: [ 46.218177] Bluetooth: HCI device and connection manager initialized Oct 30 09:59:30 rechenplan kernel: [ 46.218182] Bluetooth: HCI socket layer initialized Oct 30 09:59:30 rechenplan bluetoothd[5939]: Starting SDP server Oct 30 09:59:30 rechenplan kernel: [ 46.236585] Bluetooth: L2CAP ver 2.11 Oct 30 09:59:30 rechenplan kernel: [ 46.236598] Bluetooth: L2CAP socket layer initialized Oct 30 09:59:30 rechenplan kernel: [ 46.285880] Bluetooth: SCO (Voice Link) ver 0.6 Oct 30 09:59:30 rechenplan kernel: [ 46.285889] Bluetooth: SCO socket layer initialized Oct 30 09:59:30 rechenplan bluetoothd[5939]: Starting experimental netlink support Oct 30 09:59:30 rechenplan bluetoothd[5939]: Failed to find Bluetooth netlink family Oct 30 09:59:30 rechenplan bluetoothd[5939]: Can't init plugin /usr/lib/bluetooth/plugins/netlink.so Oct 30 09:59:30 rechenplan kernel: [ 46.312952] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Oct 30 09:59:30 rechenplan kernel: [ 46.312962] Bluetooth: BNEP filters: protocol multicast Oct 30 09:59:30 rechenplan kernel: [ 46.366717] Bridge firewalling registered Oct 30 09:59:30 rechenplan kernel: [ 46.367092] pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature. Oct 30 09:59:30 rechenplan bluetoothd[5939]: bridge pan0 created Oct 30 09:59:30 rechenplan kernel: [ 46.609104] Bluetooth: RFCOMM socket layer initialized Oct 30 09:59:30 rechenplan kernel: [ 46.609133] Bluetooth: RFCOMM TTY layer initialized Oct 30 09:59:30 rechenplan kernel: [ 46.609136] Bluetooth: RFCOMM ver 1.10 Oct 30 09:59:30 rechenplan NetworkManager: <info> starting... Oct 30 09:59:30 rechenplan NetworkManager: <info> eth0: driver is 'r8169'. Oct 30 09:59:30 rechenplan NetworkManager: <info> Found new Ethernet device 'eth0'. Oct 30 09:59:30 rechenplan NetworkManager: <info> (eth0): exported as /org/freedesktop/Hal/devices/net_00_1f_d0_56_5e_a0 Oct 30 09:59:30 rechenplan NetworkManager: <info> Trying to start the supplicant... Oct 30 09:59:30 rechenplan NetworkManager: <info> Trying to start the system settings daemon... Oct 30 09:59:30 rechenplan NetworkManager: <info> (eth0): carrier now ON (device state 1) Oct 30 09:59:30 rechenplan nm-system-settings: SCPlugin-Ifupdown: init! Oct 30 09:59:30 rechenplan nm-system-settings: SCPlugin-Ifupdown: update_system_hostname Oct 30 09:59:30 rechenplan nm-system-settings: SCPluginIfupdown: guessed connection type (eth0) = 802-3-ethernet Oct 30 09:59:30 rechenplan nm-system-settings: SCPlugin-Ifupdown: update_connection_setting_from_if_block: name:eth0, type:802-3-ethernet, autoconnect:0, id:Ifupdown (eth0), uuid: 681b428f-beaf-8932-0000-000000000000 Oct 30 09:59:30 rechenplan nm-system-settings: SCPlugin-Ifupdown: addresses count: 1 Oct 30 09:59:30 rechenplan nm-system-settings: SCPlugin-Ifupdown: autoconnect Oct 30 09:59:30 rechenplan nm-system-settings: SCPluginIfupdown: management mode: unmanaged Oct 30 09:59:30 rechenplan nm-system-settings: SCPlugin-Ifupdown: devices added (udi: /org/freedesktop/Hal/devices/net_00_1f_d0_56_5e_a0, iface: eth0) Oct 30 09:59:30 rechenplan nm-system-settings: Ifupdown: get unmanaged devices count: 1 Oct 30 09:59:30 rechenplan nm-system-settings: SCPlugin-Ifupdown: (7865536) ... get_connections. Oct 30 09:59:30 rechenplan nm-system-settings: SCPlugin-Ifupdown: (7865536) connections count: 1 Oct 30 09:59:30 rechenplan nm-system-settings: Ifupdown: get unmanaged devices count: 1 Oct 30 09:59:30 rechenplan nm-system-settings: SCPlugin-Ifupdown: end _init. Oct 30 09:59:30 rechenplan nm-system-settings: Loaded plugin ifupdown: (C) 2008 Canonical Ltd. To report bugs please use the NetworkManager mailing list. Oct 30 09:59:30 rechenplan nm-system-settings: Loaded plugin keyfile: (c) 2007 - 2008 Red Hat, Inc. To report bugs please use the NetworkManager mailing list. Oct 30 09:59:30 rechenplan NetworkManager: <info> (eth0): now unmanaged Oct 30 09:59:30 rechenplan anacron[6056]: Anacron 2.3 started on 2008-10-30 Oct 30 09:59:30 rechenplan anacron[6056]: Normal exit (0 jobs run) Oct 30 09:59:31 rechenplan /usr/sbin/cron[6100]: (CRON) INFO (pidfile fd = 3) Oct 30 09:59:31 rechenplan /usr/sbin/cron[6101]: (CRON) STARTUP (fork ok) Oct 30 09:59:31 rechenplan /usr/sbin/cron[6101]: (CRON) INFO (Running @reboot jobs) Oct 30 09:59:31 rechenplan acpid: client connected from 6061[0:0] Oct 30 09:59:33 rechenplan kernel: [ 49.534607] [fglrx] GART Table is not in FRAME_BUFFER range Oct 30 09:59:33 rechenplan kernel: [ 49.605431] [fglrx] Reserved FB block: Shared offset:0, size:1000000 Oct 30 09:59:33 rechenplan kernel: [ 49.605451] [fglrx] Reserved FB block: Unshared offset:7ffc000, size:4000 Oct 30 09:59:43 rechenplan kdm_greet[6181]: Cannot open default user face Oct 30 10:00:01 rechenplan /USR/SBIN/CRON[6206]: (horst) CMD (/home/horst/ksvn/hg/upall) Oct 30 10:00:01 rechenplan /USR/SBIN/CRON[6207]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null) Oct 30 10:00:22 rechenplan anacron[6521]: Anacron 2.3 started on 2008-10-30 Oct 30 10:00:22 rechenplan anacron[6521]: Normal exit (0 jobs run) Oct 30 10:00:22 rechenplan kernel: [ 98.608169] CPU0 attaching NULL sched-domain. Oct 30 10:00:22 rechenplan kernel: [ 98.608189] CPU1 attaching NULL sched-domain. Oct 30 10:00:22 rechenplan kernel: [ 98.608193] CPU2 attaching NULL sched-domain. Oct 30 10:00:22 rechenplan kernel: [ 98.608198] CPU3 attaching NULL sched-domain. Oct 30 10:00:22 rechenplan kernel: [ 98.624635] CPU0 attaching sched-domain: Oct 30 10:00:22 rechenplan kernel: [ 98.624643] domain 0: span 0-3 level CPU Oct 30 10:00:22 rechenplan kernel: [ 98.624648] groups: 0 1 2 3 Oct 30 10:00:22 rechenplan kernel: [ 98.624657] domain 1: span 0-3 level NODE Oct 30 10:00:22 rechenplan kernel: [ 98.624661] groups: 0-3 Oct 30 10:00:22 rechenplan kernel: [ 98.624668] CPU1 attaching sched-domain: Oct 30 10:00:22 rechenplan kernel: [ 98.624671] domain 0: span 0-3 level CPU Oct 30 10:00:22 rechenplan kernel: [ 98.624675] groups: 1 2 3 0 Oct 30 10:00:22 rechenplan kernel: [ 98.624681] domain 1: span 0-3 level NODE Oct 30 10:00:22 rechenplan kernel: [ 98.624691] groups: 0-3 Oct 30 10:00:22 rechenplan kernel: [ 98.624701] CPU2 attaching sched-domain: Oct 30 10:00:22 rechenplan kernel: [ 98.624704] domain 0: span 0-3 level CPU Oct 30 10:00:22 rechenplan kernel: [ 98.624707] groups: 2 3 0 1 Oct 30 10:00:22 rechenplan kernel: [ 98.624714] domain 1: span 0-3 level NODE Oct 30 10:00:22 rechenplan kernel: [ 98.624722] groups: 0-3 Oct 30 10:00:22 rechenplan kernel: [ 98.624728] CPU3 attaching sched-domain: Oct 30 10:00:22 rechenplan kernel: [ 98.624731] domain 0: span 0-3 level CPU Oct 30 10:00:22 rechenplan kernel: [ 98.624734] groups: 3 0 1 2 Oct 30 10:00:22 rechenplan kernel: [ 98.624740] domain 1: span 0-3 level NODE Oct 30 10:00:22 rechenplan kernel: [ 98.624747] groups: 0-3 Oct 30 10:00:36 rechenplan NetworkManager: <info> Unmanaged Device found; state CONNECTED forced. (see http://bugs.launchpad.net/bugs/191889) Oct 30 10:00:36 rechenplan NetworkManager: <info> Unmanaged Device found; state CONNECTED forced. (see http://bugs.launchpad.net/bugs/191889) Oct 30 10:00:39 rechenplan python: hp-systray(init)[6663]: warning: No hp: or hpfax: devices found in any installed CUPS queue. Exiting. Oct 30 10:01:49 rechenplan kernel: [ 185.871728] type=1503 audit(1225357309.806:4): operation="inode_permission" requested_mask="r::" denied_mask="r::" fsuid=7 name="/proc/6821/net/" pid=6821 profile="/usr/sbin/cupsd" Oct 30 10:01:50 rechenplan kernel: [ 186.957497] type=1503 audit(1225357310.892:5): operation="inode_permission" requested_mask="r::" denied_mask="r::" fsuid=7 name="/proc/6825/net/" pid=6825 profile="/usr/sbin/cupsd" Oct 30 10:01:50 rechenplan kernel: [ 186.957549] type=1503 audit(1225357310.892:6): operation="socket_create" family="ax25" sock_type="dgram" protocol=0 pid=6825 profile="/usr/sbin/cupsd" Oct 30 10:01:50 rechenplan kernel: [ 186.957560] type=1503 audit(1225357310.892:7): operation="socket_create" family="netrom" sock_type="seqpacket" protocol=0 pid=6825 profile="/usr/sbin/cupsd" Oct 30 10:01:50 rechenplan kernel: [ 186.957571] type=1503 audit(1225357310.892:8): operation="socket_create" family="rose" sock_type="dgram" protocol=0 pid=6825 profile="/usr/sbin/cupsd" Oct 30 10:01:50 rechenplan kernel: [ 186.957580] type=1503 audit(1225357310.892:9): operation="socket_create" family="ipx" sock_type="dgram" protocol=0 pid=6825 profile="/usr/sbin/cupsd" Oct 30 10:01:50 rechenplan kernel: [ 186.957589] type=1503 audit(1225357310.892:10): operation="socket_create" family="appletalk" sock_type="dgram" protocol=0 pid=6825 profile="/usr/sbin/cupsd" Oct 30 10:01:50 rechenplan kernel: [ 186.957600] type=1503 audit(1225357310.892:11): operation="socket_create" family="econet" sock_type="dgram" protocol=0 pid=6825 profile="/usr/sbin/cupsd" Oct 30 10:01:50 rechenplan kernel: [ 186.957610] type=1503 audit(1225357310.892:12): operation="socket_create" family="ash" sock_type="dgram" protocol=0 pid=6825 profile="/usr/sbin/cupsd" Oct 30 10:01:50 rechenplan kernel: [ 186.957619] type=1503 audit(1225357310.892:13): operation="socket_create" family="x25" sock_type="seqpacket" protocol=0 pid=6825 profile="/usr/sbin/cupsd" Oct 30 10:03:35 rechenplan ntpd[4670]: synchronized to 91.189.94.4, stratum 2 Oct 30 10:03:35 rechenplan ntpd[4670]: kernel time sync status change 0001 Oct 30 10:10:01 rechenplan /USR/SBIN/CRON[6842]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null) Oct 30 10:17:01 rechenplan /USR/SBIN/CRON[6933]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Oct 30 10:20:01 rechenplan /USR/SBIN/CRON[6995]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null) Oct 30 10:20:01 rechenplan /USR/SBIN/CRON[7008]: (horst) CMD (/home/horst/ksvn/hg/upall) Oct 30 10:30:02 rechenplan /USR/SBIN/CRON[7205]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null) Oct 30 10:40:02 rechenplan /USR/SBIN/CRON[7398]: (horst) CMD (/home/horst/ksvn/hg/upall) Oct 30 10:40:02 rechenplan /USR/SBIN/CRON[7407]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null) Oct 30 10:50:01 rechenplan /USR/SBIN/CRON[7627]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null) LIVE CD /var/log/syslog: Oct 30 11:56:21 ubuntu syslogd 1.5.0#2ubuntu6: restart. Oct 30 11:56:21 ubuntu kernel: Inspecting /boot/System.map-2.6.27-7-generic Oct 30 11:56:21 ubuntu kernel: Cannot find map file. Oct 30 11:56:22 ubuntu kernel: Loaded 50972 symbols from 87 modules. Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Initializing cgroup subsys cpuset Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Initializing cgroup subsys cpu Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Linux version 2.6.27-7-generic (buildd@yellow) (gcc version 4.3.2 (Ubuntu 4.3.2-1ubuntu10) ) #1 SMP Fri Oct 24 06:40:41 UTC 2008 (Ubuntu 2.6.27-7.14-generic) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/preseed/kubuntu.seed boot=casper initrd=/casper/initrd.gz nosplash -- debian-installer/language=de console-setup/layoutcode?=de Oct 30 11:56:22 ubuntu kernel: [ 0.000000] KERNEL supported cpus: Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Intel GenuineIntel Oct 30 11:56:22 ubuntu kernel: [ 0.000000] AMD AuthenticAMD Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Centaur CentaurHauls Oct 30 11:56:22 ubuntu kernel: [ 0.000000] BIOS-provided physical RAM map: Oct 30 11:56:22 ubuntu kernel: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] BIOS-e820: 0000000000100000 - 0000000077de0000 (usable) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] BIOS-e820: 0000000077de0000 - 0000000077de3000 (ACPI NVS) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] BIOS-e820: 0000000077de3000 - 0000000077df0000 (ACPI data) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] BIOS-e820: 0000000077df0000 - 0000000077e00000 (reserved) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] last_pfn = 0x77de0 max_arch_pfn = 0x3ffffffff Oct 30 11:56:22 ubuntu kernel: [ 0.000000] init_memory_mapping Oct 30 11:56:22 ubuntu kernel: [ 0.000000] 0000000000 - 0077c00000 page 2M Oct 30 11:56:22 ubuntu kernel: [ 0.000000] 0077c00000 - 0077de0000 page 4k Oct 30 11:56:22 ubuntu kernel: [ 0.000000] kernel direct mapping tables up to 77de0000 @ 8000-c000 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] last_map_addr: 77de0000 end: 77de0000 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] RAMDISK: 774e8000 - 77daf3c0 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] DMI 2.4 present. Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: RSDP 000F71C0, 0014 (r0 GBT ) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: RSDT 77DE3000, 0038 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: FACP 77DE3040, 0074 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: DSDT 77DE30C0, 6550 (r1 GBT GBTUACPI 1000 MSFT 3000000) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: FACS 77DE0000, 0040 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: SSDT 77DE9700, 0544 (r1 PTLTD POWERNOW 1 LTP 1) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: HPET 77DE9C80, 0038 (r1 GBT GBTUACPI 42302E31 GBTU 98) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: MCFG 77DE9CC0, 003C (r1 GBT GBTUACPI 42302E31 GBTU 1010101) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: APIC 77DE9640, 0084 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Scanning NUMA topology in Northbridge 24 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] No NUMA configuration found Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Faking a node at 0000000000000000-0000000077de0000 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Bootmem setup node 0 0000000000000000-0000000077de0000 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] NODE_DATA [0000000000001000 - 0000000000005fff] Oct 30 11:56:22 ubuntu kernel: [ 0.000000] bootmap [000000000000a000 - 0000000000018fbf] pages f Oct 30 11:56:22 ubuntu kernel: [ 0.000000] (6 early reservations) ==> bootmem [0000000000 - 0077de0000] Oct 30 11:56:22 ubuntu kernel: [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] Oct 30 11:56:22 ubuntu kernel: [ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] Oct 30 11:56:22 ubuntu kernel: [ 0.000000] #2 [0000200000 - 00008b8f9c] TEXT DATA BSS ==> [0000200000 - 00008b8f9c] Oct 30 11:56:22 ubuntu kernel: [ 0.000000] #3 [00774e8000 - 0077daf3c0] RAMDISK ==> [00774e8000 - 0077daf3c0] Oct 30 11:56:22 ubuntu kernel: [ 0.000000] #4 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000] Oct 30 11:56:22 ubuntu kernel: [ 0.000000] #5 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000] Oct 30 11:56:22 ubuntu kernel: [ 0.000000] found SMP MP-table at [ffff8800000f5840] 000f5840 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] [ffffe20000000000-ffffe20001dfffff] PMD -> [ffff880001200000-ffff880002ffffff] on node 0 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Zone PFN ranges: Oct 30 11:56:22 ubuntu kernel: [ 0.000000] DMA 0x00000000 -> 0x00001000 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] DMA32 0x00001000 -> 0x00100000 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Normal 0x00100000 -> 0x00100000 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Movable zone start PFN for each node Oct 30 11:56:22 ubuntu kernel: [ 0.000000] early_node_map[2] active PFN ranges Oct 30 11:56:22 ubuntu kernel: [ 0.000000] 0: 0x00000000 -> 0x0000009f Oct 30 11:56:22 ubuntu kernel: [ 0.000000] 0: 0x00000100 -> 0x00077de0 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] On node 0 totalpages: 490879 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] DMA zone: 2112 pages, LIFO batch:0 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] DMA32 zone: 479272 pages, LIFO batch:31 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: PM-Timer IO Port: 0x4008 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: Local APIC address 0xfee00000 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1]) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: IRQ0 used by override. Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: IRQ2 used by override. Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: IRQ9 used by override. Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Setting APIC routing to flat Oct 30 11:56:22 ubuntu kernel: [ 0.000000] ACPI: HPET id: 0x10b9a201 base: 0xfed00000 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Using ACPI (MADT) for SMP configuration information Oct 30 11:56:22 ubuntu kernel: [ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs Oct 30 11:56:22 ubuntu kernel: [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Allocating PCI resources starting at 78000000 (gap: 77e00000:68200000) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] PERCPU: Allocating 64928 bytes of per cpu data Oct 30 11:56:22 ubuntu kernel: [ 0.000000] NR_CPUS: 64, nr_cpu_ids: 4, nr_node_ids 1 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 481384 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Policy zone: DMA32 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Kernel command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/preseed/kubuntu.seed boot=casper initrd=/casper/initrd.gz nosplash -- debian-installer/language=de console-setup/layoutcode?=de Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Initializing CPU#0 Oct 30 11:56:22 ubuntu kernel: [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) Oct 30 11:56:22 ubuntu kernel: [ 0.000000] TSC: PIT calibration confirmed by PMTIMER. Oct 30 11:56:22 ubuntu kernel: [ 0.000000] TSC: using PIT calibration value Oct 30 11:56:22 ubuntu kernel: [ 0.000000] Detected 2004.255 MHz processor. Oct 30 11:56:22 ubuntu kernel: [ 0.004000] Console: colour VGA+ 80x25 Oct 30 11:56:22 ubuntu kernel: [ 0.004000] console [tty0] enabled Oct 30 11:56:22 ubuntu kernel: [ 0.004000] Checking aperture... Oct 30 11:56:22 ubuntu kernel: [ 0.004000] No AGP bridge found Oct 30 11:56:22 ubuntu kernel: [ 0.004000] Node 0: aperture @ 5086000000 size 32 MB Oct 30 11:56:22 ubuntu kernel: [ 0.004000] Aperture beyond 4GB. Ignoring. Oct 30 11:56:22 ubuntu kernel: [ 0.004000] Memory: 1916492k/1963904k available (3112k kernel code, 47024k reserved, 1575k data, 536k init) Oct 30 11:56:22 ubuntu kernel: [ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated Oct 30 11:56:22 ubuntu kernel: [ 0.004000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 Oct 30 11:56:22 ubuntu kernel: [ 0.004000] hpet clockevent registered Oct 30 11:56:22 ubuntu kernel: [ 0.004008] Calibrating delay loop (skipped), value calculated using timer frequency.. 4008.50 BogoMIPS (lpj=8017008) Oct 30 11:56:22 ubuntu kernel: [ 0.004092] Security Framework initialized Oct 30 11:56:22 ubuntu kernel: [ 0.004129] SELinux: Disabled at boot. Oct 30 11:56:22 ubuntu kernel: [ 0.004172] AppArmor: AppArmor initialized Oct 30 11:56:22 ubuntu kernel: [ 0.004388] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Oct 30 11:56:22 ubuntu kernel: [ 0.005248] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Oct 30 11:56:22 ubuntu kernel: [ 0.005625] Mount-cache hash table entries: 256 Oct 30 11:56:22 ubuntu kernel: [ 0.005803] Initializing cgroup subsys ns Oct 30 11:56:22 ubuntu kernel: [ 0.005838] Initializing cgroup subsys cpuacct Oct 30 11:56:22 ubuntu kernel: [ 0.005872] Initializing cgroup subsys memory Oct 30 11:56:22 ubuntu kernel: [ 0.005916] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) Oct 30 11:56:22 ubuntu kernel: [ 0.005951] CPU: L2 Cache: 512K (64 bytes/line) Oct 30 11:56:22 ubuntu kernel: [ 0.005984] CPU 0/0 -> Node 0 Oct 30 11:56:22 ubuntu kernel: [ 0.006017] tseg: 0077e00000 Oct 30 11:56:22 ubuntu kernel: [ 0.006019] CPU: Physical Processor ID: 0 Oct 30 11:56:22 ubuntu kernel: [ 0.006051] CPU: Processor Core ID: 0 Oct 30 11:56:22 ubuntu kernel: [ 0.006090] using C1E aware idle routine Oct 30 11:56:22 ubuntu kernel: [ 0.007542] ACPI: Core revision 20080609 Oct 30 11:56:22 ubuntu kernel: [ 0.009685] ACPI: Checking initramfs for custom DSDT Oct 30 11:56:22 ubuntu kernel: [ 0.356629] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 Oct 30 11:56:22 ubuntu kernel: [ 0.398941] CPU0: AMD Phenom(tm) 9350e Quad-Core Processor stepping 03 Oct 30 11:56:22 ubuntu kernel: [ 0.399032] Using local APIC timer interrupts. Oct 30 11:56:22 ubuntu kernel: [ 0.400026] APIC timer calibration result 12526593 Oct 30 11:56:22 ubuntu kernel: [ 0.400028] Detected 12.526 MHz APIC timer. Oct 30 11:56:22 ubuntu kernel: [ 0.400180] Booting processor 1/1 ip 6000 Oct 30 11:56:22 ubuntu kernel: [ 0.004000] Initializing CPU#1 Oct 30 11:56:22 ubuntu kernel: [ 0.004000] Calibrating delay using timer specific routine.. 4008.74 BogoMIPS (lpj=8017489) Oct 30 11:56:22 ubuntu kernel: [ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) Oct 30 11:56:22 ubuntu kernel: [ 0.004000] CPU: L2 Cache: 512K (64 bytes/line) Oct 30 11:56:22 ubuntu kernel: [ 0.004000] CPU 1/1 -> Node 0 Oct 30 11:56:22 ubuntu kernel: [ 0.004000] CPU: Physical Processor ID: 0 Oct 30 11:56:22 ubuntu kernel: [ 0.004000] CPU: Processor Core ID: 1 Oct 30 11:56:22 ubuntu kernel: [ 0.488393] CPU1: AMD Phenom(tm) 9350e Quad-Core Processor stepping 03 Oct 30 11:56:22 ubuntu kernel: [ 0.488708] checking TSC synchronization [CPU#0 -> CPU#1]: passed. Oct 30 11:56:22 ubuntu kernel: [ 0.492107] Booting processor 2/2 ip 6000 Oct 30 11:56:22 ubuntu kernel: [ 0.004000] Initializing CPU#2 Oct 30 11:56:22 ubuntu kernel: [ 0.004000] Calibrating delay using timer specific routine.. 4008.64 BogoMIPS (lpj=8017291) Oct 30 11:56:22 ubuntu kernel: [ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) Oct 30 11:56:22 ubuntu kernel: [ 0.004000] CPU: L2 Cache: 512K (64 bytes/line) Oct 30 11:56:22 ubuntu kernel: [ 0.004000] CPU 2/2 -> Node 0 Oct 30 11:56:22 ubuntu kernel: [ 0.004000] CPU: Physical Processor ID: 0 Oct 30 11:56:22 ubuntu kernel: [ 0.004000] CPU: Processor Core ID: 2 Oct 30 11:56:22 ubuntu kernel: [ 0.580405] CPU2: AMD Phenom(tm) 9350e Quad-Core Processor stepping 03 Oct 30 11:56:22 ubuntu kernel: [ 0.580720] checking TSC synchronization [CPU#0 -> CPU#2]: passed. Oct 30 11:56:22 ubuntu kernel: [ 0.584109] Booting processor 3/3 ip 6000 Oct 30 11:56:22 ubuntu kernel: [ 0.004000] Initializing CPU#3 Oct 30 11:56:22 ubuntu kernel: [ 0.004000] Calibrating delay using timer specific routine.. 4008.63 BogoMIPS (lpj=8017262) Oct 30 11:56:22 ubuntu kernel: [ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) Oct 30 11:56:22 ubuntu kernel: [ 0.004000] CPU: L2 Cache: 512K (64 bytes/line) Oct 30 11:56:22 ubuntu kernel: [ 0.004000] CPU 3/3 -> Node 0 Oct 30 11:56:22 ubuntu kernel: [ 0.004000] CPU: Physical Processor ID: 0 Oct 30 11:56:22 ubuntu kernel: [ 0.004000] CPU: Processor Core ID: 3 Oct 30 11:56:22 ubuntu kernel: [ 0.672413] CPU3: AMD Phenom(tm) 9350e Quad-Core Processor stepping 03 Oct 30 11:56:22 ubuntu kernel: [ 0.672729] checking TSC synchronization [CPU#0 -> CPU#3]: passed. Oct 30 11:56:22 ubuntu kernel: [ 0.676054] Brought up 4 CPUs Oct 30 11:56:22 ubuntu kernel: [ 0.676087] Total of 4 processors activated (16034.52 BogoMIPS). Oct 30 11:56:22 ubuntu kernel: [ 0.676206] CPU0 attaching sched-domain: Oct 30 11:56:22 ubuntu kernel: [ 0.676208] domain 0: span 0-3 level CPU Oct 30 11:56:22 ubuntu kernel: [ 0.676211] groups: 0 1 2 3 Oct 30 11:56:22 ubuntu kernel: [ 0.676215] domain 1: span 0-3 level NODE Oct 30 11:56:22 ubuntu kernel: [ 0.676217] groups: 0-3 Oct 30 11:56:22 ubuntu kernel: [ 0.676221] CPU1 attaching sched-domain: Oct 30 11:56:22 ubuntu kernel: [ 0.676223] domain 0: span 0-3 level CPU Oct 30 11:56:22 ubuntu kernel: [ 0.676224] groups: 1 2 3 0 Oct 30 11:56:22 ubuntu kernel: [ 0.676228] domain 1: span 0-3 level NODE Oct 30 11:56:22 ubuntu kernel: [ 0.676230] groups: 0-3 Oct 30 11:56:22 ubuntu kernel: [ 0.676233] CPU2 attaching sched-domain: Oct 30 11:56:22 ubuntu kernel: [ 0.676234] domain 0: span 0-3 level CPU Oct 30 11:56:22 ubuntu kernel: [ 0.676236] groups: 2 3 0 1 Oct 30 11:56:22 ubuntu kernel: [ 0.676239] domain 1: span 0-3 level NODE Oct 30 11:56:22 ubuntu kernel: [ 0.676241] groups: 0-3 Oct 30 11:56:22 ubuntu kernel: [ 0.676243] CPU3 attaching sched-domain: Oct 30 11:56:22 ubuntu kernel: [ 0.676245] domain 0: span 0-3 level CPU Oct 30 11:56:22 ubuntu kernel: [ 0.676246] groups: 3 0 1 2 Oct 30 11:56:22 ubuntu kernel: [ 0.676250] domain 1: span 0-3 level NODE Oct 30 11:56:22 ubuntu kernel: [ 0.676251] groups: 0-3 Oct 30 11:56:22 ubuntu kernel: [ 0.676375] net_namespace: 1552 bytes Oct 30 11:56:22 ubuntu kernel: [ 0.676375] Booting paravirtualized kernel on bare hardware Oct 30 11:56:22 ubuntu kernel: [ 0.676375] Time: 11:54:24 Date: 10/30/08 Oct 30 11:56:22 ubuntu kernel: [ 0.676420] NET: Registered protocol family 16 Oct 30 11:56:22 ubuntu kernel: [ 0.676470] node 0 link 0: io port [c000, ffff] Oct 30 11:56:22 ubuntu kernel: [ 0.676470] TOM: 0000000080000000 aka 2048M Oct 30 11:56:22 ubuntu kernel: [ 0.676470] Fam 10h mmconf [e0000000, e00fffff] Oct 30 11:56:22 ubuntu kernel: [ 0.676470] node 0 link 0: mmio [a0000, bffff] Oct 30 11:56:22 ubuntu kernel: [ 0.676470] node 0 link 0: mmio [80000000, fe02ffff] ==> [80000000, dfffffff] and [e0100000, fe02ffff] Oct 30 11:56:22 ubuntu kernel: [ 0.676470] node 0 link 0: mmio [e0000000, efffffff] ==> [e0100000, efffffff] Oct 30 11:56:22 ubuntu kernel: [ 0.676470] bus: [00,03] on node 0 link 0 Oct 30 11:56:22 ubuntu kernel: [ 0.676470] bus: 00 index 0 io port: [0, ffff] Oct 30 11:56:22 ubuntu kernel: [ 0.676470] bus: 00 index 1 mmio: [a0000, bffff] Oct 30 11:56:22 ubuntu kernel: [ 0.676470] bus: 00 index 2 mmio: [80000000, dfffffff] Oct 30 11:56:22 ubuntu kernel: [ 0.676470] bus: 00 index 3 mmio: [e0100000, fcffffffff] Oct 30 11:56:22 ubuntu kernel: [ 0.676470] ACPI: bus type pci registered Oct 30 11:56:22 ubuntu kernel: [ 0.676470] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 Oct 30 11:56:22 ubuntu kernel: [ 0.676470] PCI: MCFG area at e0000000 reserved in E820 Oct 30 11:56:22 ubuntu kernel: [ 0.691475] PCI: Using MMCONFIG at e0000000 - efffffff Oct 30 11:56:22 ubuntu kernel: [ 0.691509] PCI: Using configuration type 1 for base access Oct 30 11:56:22 ubuntu kernel: [ 0.692633] ACPI: EC: Look up EC in DSDT Oct 30 11:56:22 ubuntu kernel: [ 0.703086] ACPI: Interpreter enabled Oct 30 11:56:22 ubuntu kernel: [ 0.703125] ACPI: (supports S0 S3 S4 S5) Oct 30 11:56:22 ubuntu kernel: [ 0.703284] ACPI: Using IOAPIC for interrupt routing Oct 30 11:56:22 ubuntu kernel: [ 0.709336] ACPI: PCI Root Bridge [PCI0] (0000:00) Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:00.0 reg 1c 64bit mmio: [e0000000, ffffffff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold Oct 30 11:56:22 ubuntu kernel: [ 0.709336] pci 0000:00:0a.0: PME# disabled Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:11.0 reg 10 io port: [ff00, ff07] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:11.0 reg 14 io port: [fe00, fe03] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:11.0 reg 18 io port: [fd00, fd07] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:11.0 reg 1c io port: [fc00, fc03] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:11.0 reg 20 io port: [fb00, fb0f] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:11.0 reg 24 32bit mmio: [fe02f000, fe02f3ff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:12.0 reg 10 32bit mmio: [fe02e000, fe02efff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:12.1 reg 10 32bit mmio: [fe02d000, fe02dfff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:12.2 reg 10 32bit mmio: [fe02c000, fe02c0ff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] pci 0000:00:12.2: supports D1 Oct 30 11:56:22 ubuntu kernel: [ 0.709336] pci 0000:00:12.2: supports D2 Oct 30 11:56:22 ubuntu kernel: [ 0.709336] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot Oct 30 11:56:22 ubuntu kernel: [ 0.709336] pci 0000:00:12.2: PME# disabled Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:13.0 reg 10 32bit mmio: [fe02b000, fe02bfff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:13.1 reg 10 32bit mmio: [fe02a000, fe02afff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:13.2 reg 10 32bit mmio: [fe029000, fe0290ff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] pci 0000:00:13.2: supports D1 Oct 30 11:56:22 ubuntu kernel: [ 0.709336] pci 0000:00:13.2: supports D2 Oct 30 11:56:22 ubuntu kernel: [ 0.709336] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot Oct 30 11:56:22 ubuntu kernel: [ 0.709336] pci 0000:00:13.2: PME# disabled Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:14.1 reg 10 io port: [0, 7] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:14.1 reg 14 io port: [0, 3] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:14.1 reg 18 io port: [0, 7] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:14.1 reg 1c io port: [0, 3] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:14.1 reg 20 io port: [fa00, fa0f] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:00:14.5 reg 10 32bit mmio: [fe028000, fe028fff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:01:05.0 reg 10 32bit mmio: [d8000000, dfffffff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:01:05.0 reg 14 io port: [ee00, eeff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:01:05.0 reg 18 32bit mmio: [fdee0000, fdeeffff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:01:05.0 reg 24 32bit mmio: [fdd00000, fddfffff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] pci 0000:01:05.0: supports D1 Oct 30 11:56:22 ubuntu kernel: [ 0.709336] pci 0000:01:05.0: supports D2 Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:01:05.1 reg 10 32bit mmio: [fdefc000, fdefffff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] pci 0000:01:05.1: supports D1 Oct 30 11:56:22 ubuntu kernel: [ 0.709336] pci 0000:01:05.1: supports D2 Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: bridge 0000:00:01.0 io port: [e000, efff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: bridge 0000:00:01.0 32bit mmio: [fdd00000, fdefffff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: bridge 0000:00:01.0 64bit mmio pref: [d8000000, dfffffff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:02:00.0 reg 10 io port: [de00, deff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:02:00.0 reg 18 32bit mmio: [fdfff000, fdffffff] Oct 30 11:56:22 ubuntu kernel: [ 0.709336] PCI: 0000:02:00.0 reg 20 32bit mmio: [fdfe0000, fdfeffff] Oct 30 11:56:22 ubuntu kernel: [ 0.709342] PCI: 0000:02:00.0 reg 30 32bit mmio: [0, ffff] Oct 30 11:56:22 ubuntu kernel: [ 0.709362] pci 0000:02:00.0: supports D1 Oct 30 11:56:22 ubuntu kernel: [ 0.709364] pci 0000:02:00.0: supports D2 Oct 30 11:56:22 ubuntu kernel: [ 0.709365] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold Oct 30 11:56:22 ubuntu kernel: [ 0.709401] pci 0000:02:00.0: PME# disabled Oct 30 11:56:22 ubuntu kernel: [ 0.709472] PCI: bridge 0000:00:0a.0 io port: [d000, dfff] Oct 30 11:56:22 ubuntu kernel: [ 0.709474] PCI: bridge 0000:00:0a.0 32bit mmio: [fda00000, fdafffff] Oct 30 11:56:22 ubuntu kernel: [ 0.709478] PCI: bridge 0000:00:0a.0 64bit mmio pref: [fdf00000, fdffffff] Oct 30 11:56:22 ubuntu kernel: [ 0.709529] PCI: 0000:03:07.0 reg 10 io port: [cf00, cf1f] Oct 30 11:56:22 ubuntu kernel: [ 0.709537] PCI: 0000:03:07.0 reg 14 io port: [ce00, ce7f] Oct 30 11:56:22 ubuntu kernel: [ 0.709585] pci 0000:03:07.0: supports D2 Oct 30 11:56:22 ubuntu kernel: [ 0.709623] pci 0000:00:14.4: transparent bridge Oct 30 11:56:22 ubuntu kernel: [ 0.709658] PCI: bridge 0000:00:14.4 io port: [c000, cfff] Oct 30 11:56:22 ubuntu kernel: [ 0.709662] PCI: bridge 0000:00:14.4 32bit mmio: [fdc00000, fdcfffff] Oct 30 11:56:22 ubuntu kernel: [ 0.709666] PCI: bridge 0000:00:14.4 32bit mmio pref: [fdb00000, fdbfffff] Oct 30 11:56:22 ubuntu kernel: [ 0.709683] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] Oct 30 11:56:22 ubuntu kernel: [ 0.712159] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] Oct 30 11:56:22 ubuntu kernel: [ 0.712356] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCEA._PRT] Oct 30 11:56:22 ubuntu kernel: [ 0.712489] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] Oct 30 11:56:22 ubuntu kernel: [ 0.741524] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled. Oct 30 11:56:22 ubuntu kernel: [ 0.741524] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled. Oct 30 11:56:22 ubuntu kernel: [ 0.744485] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled. Oct 30 11:56:22 ubuntu kernel: [ 0.744971] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled. Oct 30 11:56:22 ubuntu kernel: [ 0.745951] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled. Oct 30 11:56:22 ubuntu kernel: [ 0.746445] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled. Oct 30 11:56:22 ubuntu kernel: [ 0.746925] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11) *0, disabled. Oct 30 11:56:22 ubuntu kernel: [ 0.747414] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled. Oct 30 11:56:22 ubuntu kernel: [ 0.747826] Linux Plug and Play Support v0.97 (c) Adam Belay Oct 30 11:56:22 ubuntu kernel: [ 0.748037] pnp: PnP ACPI init Oct 30 11:56:22 ubuntu kernel: [ 0.748074] ACPI: bus type pnp registered Oct 30 11:56:22 ubuntu kernel: [ 0.749045] pnp 00:09: mem resource (0xe0000000-0xefffffff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling Oct 30 11:56:22 ubuntu kernel: [ 0.749045] pnp 00:0a: mem resource (0xffff0000-0xffffffff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling Oct 30 11:56:22 ubuntu kernel: [ 0.749045] pnp 00:0a: mem resource (0xfec00000-0xfec00fff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling Oct 30 11:56:22 ubuntu kernel: [ 0.749045] pnp 00:0a: mem resource (0xfee00000-0xfee00fff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling Oct 30 11:56:22 ubuntu kernel: [ 0.749045] pnp 00:0a: mem resource (0xfff80000-0xfffeffff) overlaps 0000:00:00.0 BAR 3 (0xe0000000-0xffffffff), disabling Oct 30 11:56:22 ubuntu kernel: [ 0.749045] pnp: PnP ACPI: found 11 devices Oct 30 11:56:22 ubuntu kernel: [ 0.749045] ACPI: ACPI bus type pnp unregistered Oct 30 11:56:22 ubuntu kernel: [ 0.752046] PCI: Using ACPI for IRQ routing Oct 30 11:56:22 ubuntu kernel: [ 0.752073] pci 0000:00:00.0: BAR 3: can't allocate resource Oct 30 11:56:22 ubuntu kernel: [ 0.772041] NET: Registered protocol family 8 Oct 30 11:56:22 ubuntu kernel: [ 0.772075] NET: Registered protocol family 20 Oct 30 11:56:22 ubuntu kernel: [ 0.772119] NetLabel: Initializing Oct 30 11:56:22 ubuntu kernel: [ 0.772119] NetLabel: domain hash size = 128 Oct 30 11:56:22 ubuntu kernel: [ 0.772119] NetLabel: protocols = UNLABELED CIPSOv4 Oct 30 11:56:22 ubuntu kernel: [ 0.772142] NetLabel: unlabeled traffic allowed by default Oct 30 11:56:22 ubuntu kernel: [ 0.772233] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 Oct 30 11:56:22 ubuntu kernel: [ 0.772310] hpet0: 4 32-bit timers, 14318180 Hz Oct 30 11:56:22 ubuntu kernel: [ 0.776041] Switched to high resolution mode on CPU 0 Oct 30 11:56:22 ubuntu kernel: [ 0.776748] tracer: 1286 pages allocated for 65536 entries of 80 bytes Oct 30 11:56:22 ubuntu kernel: [ 0.776782] actual entries 65586 Oct 30 11:56:22 ubuntu kernel: [ 0.776802] Switched to high resolution mode on CPU 1 Oct 30 11:56:22 ubuntu kernel: [ 0.776812] Switched to high resolution mode on CPU 2 Oct 30 11:56:22 ubuntu kernel: [ 0.776822] Switched to high resolution mode on CPU 3 Oct 30 11:56:22 ubuntu kernel: [ 0.776898] AppArmor: AppArmor Filesystem Enabled Oct 30 11:56:22 ubuntu kernel: [ 0.776949] ACPI: RTC can wake from S4 Oct 30 11:56:22 ubuntu kernel: [ 0.792028] system 00:01: ioport range 0x4d0-0x4d1 has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792064] system 00:01: ioport range 0x220-0x225 has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792098] system 00:01: ioport range 0x290-0x294 has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792135] system 00:02: ioport range 0x4100-0x411f has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792171] system 00:02: ioport range 0x228-0x22f has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792205] system 00:02: ioport range 0x238-0x23f has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792239] system 00:02: ioport range 0x40b-0x40b has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792273] system 00:02: ioport range 0x4d6-0x4d6 has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792308] system 00:02: ioport range 0xc00-0xc01 has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792343] system 00:02: ioport range 0xc14-0xc14 has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792377] system 00:02: ioport range 0xc50-0xc52 has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792412] system 00:02: ioport range 0xc6c-0xc6d has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792446] system 00:02: ioport range 0xc6f-0xc6f has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792481] system 00:02: ioport range 0xcd0-0xcd1 has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792516] system 00:02: ioport range 0xcd2-0xcd3 has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792550] system 00:02: ioport range 0xcd4-0xcdf has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792584] system 00:02: ioport range 0x4000-0x40fe has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792619] system 00:02: ioport range 0x4210-0x4217 has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792653] system 00:02: ioport range 0xb00-0xb0f has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792688] system 00:02: ioport range 0xb10-0xb1f has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792722] system 00:02: ioport range 0xb20-0xb3f has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792770] system 00:0a: iomem range 0xd1a00-0xd3fff has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792805] system 00:0a: iomem range 0xf0000-0xf7fff could not be reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792840] system 00:0a: iomem range 0xf8000-0xfbfff could not be reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792875] system 00:0a: iomem range 0xfc000-0xfffff could not be reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792909] system 00:0a: iomem range 0x77de0000-0x77dfffff could not be reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792947] system 00:0a: iomem range 0x0-0x9ffff could not be reserved Oct 30 11:56:22 ubuntu kernel: [ 0.792982] system 00:0a: iomem range 0x100000-0x77ddffff could not be reserved Oct 30 11:56:22 ubuntu kernel: [ 0.793019] system 00:0a: iomem range 0x77ef0000-0x7feeffff has been reserved Oct 30 11:56:22 ubuntu kernel: [ 0.798179] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 Oct 30 11:56:22 ubuntu kernel: [ 0.798214] pci 0000:00:01.0: IO window: 0xe000-0xefff Oct 30 11:56:22 ubuntu kernel: [ 0.798249] pci 0000:00:01.0: MEM window: 0xfdd00000-0xfdefffff Oct 30 11:56:22 ubuntu kernel: [ 0.798285] pci 0000:00:01.0: PREFETCH window: 0x000000d8000000-0x000000dfffffff Oct 30 11:56:22 ubuntu kernel: [ 0.798324] pci 0000:00:0a.0: PCI bridge, secondary bus 0000:02 Oct 30 11:56:22 ubuntu kernel: [ 0.798359] pci 0000:00:0a.0: IO window: 0xd000-0xdfff Oct 30 11:56:22 ubuntu kernel: [ 0.798393] pci 0000:00:0a.0: MEM window: 0xfda00000-0xfdafffff Oct 30 11:56:22 ubuntu kernel: [ 0.798428] pci 0000:00:0a.0: PREFETCH window: 0x000000fdf00000-0x000000fdffffff Oct 30 11:56:22 ubuntu kernel: [ 0.798466] pci 0000:00:14.4: PCI bridge, secondary bus 0000:03 Oct 30 11:56:22 ubuntu kernel: [ 0.798502] pci 0000:00:14.4: IO window: 0xc000-0xcfff Oct 30 11:56:22 ubuntu kernel: [ 0.798538] pci 0000:00:14.4: MEM window: 0xfdc00000-0xfdcfffff Oct 30 11:56:22 ubuntu kernel: [ 0.798574] pci 0000:00:14.4: PREFETCH window: 0x000000fdb00000-0x000000fdbfffff Oct 30 11:56:22 ubuntu kernel: [ 0.798630] pci 0000:00:0a.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Oct 30 11:56:22 ubuntu kernel: [ 0.798665] pci 0000:00:0a.0: setting latency timer to 64 Oct 30 11:56:22 ubuntu kernel: [ 0.798672] bus: 00 index 0 io port: [0, ffff] Oct 30 11:56:22 ubuntu kernel: [ 0.798705] bus: 00 index 1 mmio: [0, ffffffffffffffff] Oct 30 11:56:22 ubuntu kernel: [ 0.798739] bus: 01 index 0 io port: [e000, efff] Oct 30 11:56:22 ubuntu kernel: [ 0.798772] bus: 01 index 1 mmio: [fdd00000, fdefffff] Oct 30 11:56:22 ubuntu kernel: [ 0.798806] bus: 01 index 2 mmio: [d8000000, dfffffff] Oct 30 11:56:22 ubuntu kernel: [ 0.798839] bus: 01 index 3 mmio: [0, 0] Oct 30 11:56:22 ubuntu kernel: [ 0.798871] bus: 02 index 0 io port: [d000, dfff] Oct 30 11:56:22 ubuntu kernel: [ 0.798904] bus: 02 index 1 mmio: [fda00000, fdafffff] Oct 30 11:56:22 ubuntu kernel: [ 0.798938] bus: 02 index 2 mmio: [fdf00000, fdffffff] Oct 30 11:56:22 ubuntu kernel: [ 0.798971] bus: 02 index 3 mmio: [0, 0] Oct 30 11:56:22 ubuntu kernel: [ 0.799003] bus: 03 index 0 io port: [c000, cfff] Oct 30 11:56:22 ubuntu kernel: [ 0.799036] bus: 03 index 1 mmio: [fdc00000, fdcfffff] Oct 30 11:56:22 ubuntu kernel: [ 0.799070] bus: 03 index 2 mmio: [fdb00000, fdbfffff] Oct 30 11:56:22 ubuntu kernel: [ 0.799103] bus: 03 index 3 io port: [0, ffff] Oct 30 11:56:22 ubuntu kernel: [ 0.799136] bus: 03 index 4 mmio: [0, ffffffffffffffff] Oct 30 11:56:22 ubuntu kernel: [ 0.799179] NET: Registered protocol family 2 Oct 30 11:56:22 ubuntu kernel: [ 0.840129] IP route cache hash table entries: 65536 (order: 7, 524288 bytes) Oct 30 11:56:22 ubuntu kernel: [ 0.840957] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) Oct 30 11:56:22 ubuntu kernel: [ 0.842421] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) Oct 30 11:56:22 ubuntu kernel: [ 0.842792] TCP: Hash tables configured (established 262144 bind 65536) Oct 30 11:56:22 ubuntu kernel: [ 0.842826] TCP reno registered Oct 30 11:56:22 ubuntu kernel: [ 0.852108] NET: Registered protocol family 1 Oct 30 11:56:22 ubuntu kernel: [ 0.852252] checking if image is initramfs... it is Oct 30 11:56:22 ubuntu kernel: [ 1.549062] Freeing initrd memory: 8988k freed Oct 30 11:56:22 ubuntu kernel: [ 1.554035] audit: initializing netlink socket (disabled) Oct 30 11:56:22 ubuntu kernel: [ 1.554082] type=2000 audit(1225367664.552:1): initialized Oct 30 11:56:22 ubuntu kernel: [ 1.559396] HugeTLB registered 2 MB page size, pre-allocated 0 pages Oct 30 11:56:22 ubuntu kernel: [ 1.562162] VFS: Disk quotas dquot_6.5.1 Oct 30 11:56:22 ubuntu kernel: [ 1.562278] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Oct 30 11:56:22 ubuntu kernel: [ 1.562413] msgmni has been set to 3760 Oct 30 11:56:22 ubuntu kernel: [ 1.562571] io scheduler noop registered Oct 30 11:56:22 ubuntu kernel: [ 1.562604] io scheduler anticipatory registered Oct 30 11:56:22 ubuntu kernel: [ 1.562638] io scheduler deadline registered Oct 30 11:56:22 ubuntu kernel: [ 1.562795] io scheduler cfq registered (default) Oct 30 11:56:22 ubuntu kernel: [ 1.684050] pci 0000:01:05.0: Boot video device Oct 30 11:56:22 ubuntu kernel: [ 1.684183] pcieport-driver 0000:00:0a.0: setting latency timer to 64 Oct 30 11:56:22 ubuntu kernel: [ 1.684204] pcieport-driver 0000:00:0a.0: found MSI capability Oct 30 11:56:22 ubuntu kernel: [ 1.684263] pci_express 0000:00:0a.0:pcie00: allocate port service Oct 30 11:56:22 ubuntu kernel: [ 1.720860] hpet_resources: 0xfed00000 is busy Oct 30 11:56:22 ubuntu kernel: [ 1.720928] Linux agpgart interface v0.103 Oct 30 11:56:22 ubuntu kernel: [ 1.720966] Serial: 8250/16550 driver4 ports, IRQ sharing enabled Oct 30 11:56:22 ubuntu kernel: [ 1.723146] brd: module loaded Oct 30 11:56:22 ubuntu kernel: [ 1.723247] input: Macintosh mouse button emulation as /devices/virtual/input/input0 Oct 30 11:56:22 ubuntu kernel: [ 1.723390] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 Oct 30 11:56:22 ubuntu kernel: [ 1.723424] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp Oct 30 11:56:22 ubuntu kernel: [ 1.723587] serio: i8042 KBD port at 0x60,0x64 irq 1 Oct 30 11:56:22 ubuntu kernel: [ 1.740136] mice: PS/2 mouse device common for all mice Oct 30 11:56:22 ubuntu kernel: [ 1.740298] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0 Oct 30 11:56:22 ubuntu kernel: [ 1.740361] rtc0: alarms up to one month, hpet irqs Oct 30 11:56:22 ubuntu kernel: [ 1.740431] cpuidle: using governor ladder Oct 30 11:56:22 ubuntu kernel: [ 1.740465] cpuidle: using governor menu Oct 30 11:56:22 ubuntu kernel: [ 1.740875] TCP cubic registered Oct 30 11:56:22 ubuntu kernel: [ 1.741117] registered taskstats version 1 Oct 30 11:56:22 ubuntu kernel: [ 1.741275] Magic number: 12:336:935 Oct 30 11:56:22 ubuntu kernel: [ 1.741412] rtc_cmos 00:05: setting system clock to 2008-10-30 11:54:25 UTC (1225367665) Oct 30 11:56:22 ubuntu kernel: [ 1.741450] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found Oct 30 11:56:22 ubuntu kernel: [ 1.741484] EDD information not available. Oct 30 11:56:22 ubuntu kernel: [ 1.741547] Freeing unused kernel memory: 536k freed Oct 30 11:56:22 ubuntu kernel: [ 1.741775] Write protecting the kernel read-only data: 4348k Oct 30 11:56:22 ubuntu kernel: [ 1.757365] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 Oct 30 11:56:22 ubuntu kernel: [ 1.832998] fuse init (API version 7.9) Oct 30 11:56:22 ubuntu kernel: [ 1.853066] processor ACPI0007:00: registered as cooling_device0 Oct 30 11:56:22 ubuntu kernel: [ 1.853166] processor ACPI0007:01: registered as cooling_device1 Oct 30 11:56:22 ubuntu kernel: [ 1.853263] processor ACPI0007:02: registered as cooling_device2 Oct 30 11:56:22 ubuntu kernel: [ 1.853359] processor ACPI0007:03: registered as cooling_device3 Oct 30 11:56:22 ubuntu kernel: [ 2.004582] No dock devices found. Oct 30 11:56:22 ubuntu kernel: [ 2.015361] SCSI subsystem initialized Oct 30 11:56:22 ubuntu kernel: [ 2.017298] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded Oct 30 11:56:22 ubuntu kernel: [ 2.017354] r8169 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Oct 30 11:56:22 ubuntu kernel: [ 2.017404] r8169 0000:02:00.0: setting latency timer to 64 Oct 30 11:56:22 ubuntu kernel: [ 2.017697] eth0: RTL8168c/8111c at 0xffffc20000372000, 00:1f:d0:56:5e:a0, XID 3c4000c0 IRQ 2302 Oct 30 11:56:22 ubuntu kernel: [ 2.035130] libata version 3.00 loaded. Oct 30 11:56:22 ubuntu kernel: [ 2.047195] usbcore: registered new interface driver usbfs Oct 30 11:56:22 ubuntu kernel: [ 2.047280] usbcore: registered new interface driver hub Oct 30 11:56:22 ubuntu kernel: [ 2.050234] usbcore: registered new device driver usb Oct 30 11:56:22 ubuntu kernel: [ 2.050365] ahci 0000:00:11.0: version 3.0 Oct 30 11:56:22 ubuntu kernel: [ 2.050391] ahci 0000:00:11.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 Oct 30 11:56:22 ubuntu kernel: [ 2.050582] ahci 0000:00:11.0: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode Oct 30 11:56:22 ubuntu kernel: [ 2.050621] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part Oct 30 11:56:22 ubuntu kernel: [ 2.051655] scsi0 : ahci Oct 30 11:56:22 ubuntu kernel: [ 2.051793] scsi1 : ahci Oct 30 11:56:22 ubuntu kernel: [ 2.051872] scsi2 : ahci Oct 30 11:56:22 ubuntu kernel: [ 2.051951] scsi3 : ahci Oct 30 11:56:22 ubuntu kernel: [ 2.052029] scsi4 : ahci Oct 30 11:56:22 ubuntu kernel: [ 2.052108] scsi5 : ahci Oct 30 11:56:22 ubuntu kernel: [ 2.052243] ata1: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 2301 Oct 30 11:56:22 ubuntu kernel: [ 2.052281] ata2: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 2301 Oct 30 11:56:22 ubuntu kernel: [ 2.052808] ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 2301 Oct 30 11:56:22 ubuntu kernel: [ 2.052845] ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 2301 Oct 30 11:56:22 ubuntu kernel: [ 2.052882] ata5: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f300 irq 2301 Oct 30 11:56:22 ubuntu kernel: [ 2.052920] ata6: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f380 irq 2301 Oct 30 11:56:22 ubuntu kernel: [ 2.060096] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver Oct 30 11:56:22 ubuntu kernel: [ 2.536026] ata1: softreset failed (device not ready) Oct 30 11:56:22 ubuntu kernel: [ 2.536067] ata1: failed due to HW bug, retry pmp=0 Oct 30 11:56:22 ubuntu kernel: [ 2.700039] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Oct 30 11:56:22 ubuntu kernel: [ 2.706414] ata1.00: ATA-7: SAMSUNG HD642JJ, 1AA01112, max UDMA7 Oct 30 11:56:22 ubuntu kernel: [ 2.706454] ata1.00: 1250263728 sectors, multi 0: LBA48 NCQ (depth 31/32) Oct 30 11:56:22 ubuntu kernel: [ 2.712880] ata1.00: configured for UDMA/133 Oct 30 11:56:22 ubuntu kernel: [ 3.048034] ata2: SATA link down (SStatus 0 SControl 300) Oct 30 11:56:22 ubuntu kernel: [ 3.384034] ata3: SATA link down (SStatus 0 SControl 300) Oct 30 11:56:22 ubuntu kernel: [ 3.720025] ata4: SATA link down (SStatus 0 SControl 300) Oct 30 11:56:22 ubuntu kernel: [ 4.220023] ata5: softreset failed (device not ready) Oct 30 11:56:22 ubuntu kernel: [ 4.220060] ata5: failed due to HW bug, retry pmp=0 Oct 30 11:56:22 ubuntu kernel: [ 4.384029] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Oct 30 11:56:22 ubuntu kernel: [ 4.390388] ata5.00: ATA-7: SAMSUNG HD642JJ, 1AA01112, max UDMA7 Oct 30 11:56:22 ubuntu kernel: [ 4.390422] ata5.00: 1250263728 sectors, multi 0: LBA48 NCQ (depth 31/32) Oct 30 11:56:22 ubuntu kernel: [ 4.396842] ata5.00: configured for UDMA/133 Oct 30 11:56:22 ubuntu kernel: [ 4.732032] ata6: SATA link down (SStatus 0 SControl 300) Oct 30 11:56:22 ubuntu kernel: [ 4.748117] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD642JJ 1AA0 PQ: 0 ANSI: 5 Oct 30 11:56:22 ubuntu kernel: [ 4.748265] scsi 4:0:0:0: Direct-Access ATA SAMSUNG HD642JJ 1AA0 PQ: 0 ANSI: 5 Oct 30 11:56:22 ubuntu kernel: [ 4.748754] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Oct 30 11:56:22 ubuntu kernel: [ 4.748805] ohci_hcd 0000:00:12.0: OHCI Host Controller Oct 30 11:56:22 ubuntu kernel: [ 4.748886] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 1 Oct 30 11:56:22 ubuntu kernel: [ 4.748957] ohci_hcd 0000:00:12.0: irq 16, io mem 0xfe02e000 Oct 30 11:56:22 ubuntu kernel: [ 4.808118] usb usb1: configuration #1 chosen from 1 choice Oct 30 11:56:22 ubuntu kernel: [ 4.808181] hub 1-0:1.0: USB hub found Oct 30 11:56:22 ubuntu kernel: [ 4.808221] hub 1-0:1.0: 3 ports detected Oct 30 11:56:22 ubuntu kernel: [ 5.013760] ohci_hcd 0000:00:12.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Oct 30 11:56:22 ubuntu kernel: [ 5.013809] ohci_hcd 0000:00:12.1: OHCI Host Controller Oct 30 11:56:22 ubuntu kernel: [ 5.013874] ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 2 Oct 30 11:56:22 ubuntu kernel: [ 5.013926] ohci_hcd 0000:00:12.1: irq 16, io mem 0xfe02d000 Oct 30 11:56:22 ubuntu kernel: [ 5.073198] usb usb2: configuration #1 chosen from 1 choice Oct 30 11:56:22 ubuntu kernel: [ 5.073756] hub 2-0:1.0: USB hub found Oct 30 11:56:22 ubuntu kernel: [ 5.073798] hub 2-0:1.0: 3 ports detected Oct 30 11:56:22 ubuntu kernel: [ 5.176019] usb 1-2: new low speed USB device using ohci_hcd and address 2 Oct 30 11:56:22 ubuntu kernel: [ 5.177215] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17 Oct 30 11:56:22 ubuntu kernel: [ 5.177262] ehci_hcd 0000:00:12.2: EHCI Host Controller Oct 30 11:56:22 ubuntu kernel: [ 5.177334] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 3 Oct 30 11:56:22 ubuntu kernel: [ 5.177401] ehci_hcd 0000:00:12.2: debug port 1 Oct 30 11:56:22 ubuntu kernel: [ 5.177459] ehci_hcd 0000:00:12.2: irq 17, io mem 0xfe02c000 Oct 30 11:56:22 ubuntu kernel: [ 5.324020] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 Oct 30 11:56:22 ubuntu kernel: [ 5.324169] usb usb3: configuration #1 chosen from 1 choice Oct 30 11:56:22 ubuntu kernel: [ 5.324225] hub 3-0:1.0: USB hub found Oct 30 11:56:22 ubuntu kernel: [ 5.324264] hub 3-0:1.0: 6 ports detected Oct 30 11:56:22 ubuntu kernel: [ 5.533207] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Oct 30 11:56:22 ubuntu kernel: [ 5.533250] ohci_hcd 0000:00:13.0: OHCI Host Controller Oct 30 11:56:22 ubuntu kernel: [ 5.533309] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 4 Oct 30 11:56:22 ubuntu kernel: [ 5.533370] ohci_hcd 0000:00:13.0: irq 18, io mem 0xfe02b000 Oct 30 11:56:22 ubuntu kernel: [ 5.592087] usb usb4: configuration #1 chosen from 1 choice Oct 30 11:56:22 ubuntu kernel: [ 5.592143] hub 4-0:1.0: USB hub found Oct 30 11:56:22 ubuntu kernel: [ 5.592182] hub 4-0:1.0: 3 ports detected Oct 30 11:56:22 ubuntu kernel: [ 5.693291] ohci_hcd 0000:00:13.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Oct 30 11:56:22 ubuntu kernel: [ 5.693334] ohci_hcd 0000:00:13.1: OHCI Host Controller Oct 30 11:56:22 ubuntu kernel: [ 5.693390] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 5 Oct 30 11:56:22 ubuntu kernel: [ 5.693439] ohci_hcd 0000:00:13.1: irq 18, io mem 0xfe02a000 Oct 30 11:56:22 ubuntu kernel: [ 5.720020] usb 1-2: device not accepting address 2, error -62 Oct 30 11:56:22 ubuntu kernel: [ 5.752083] usb usb5: configuration #1 chosen from 1 choice Oct 30 11:56:22 ubuntu kernel: [ 5.752138] hub 5-0:1.0: USB hub found Oct 30 11:56:22 ubuntu kernel: [ 5.752177] hub 5-0:1.0: 3 ports detected Oct 30 11:56:22 ubuntu kernel: [ 5.776030] hub 1-0:1.0: unable to enumerate USB device on port 2 Oct 30 11:56:22 ubuntu kernel: [ 5.956175] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 Oct 30 11:56:22 ubuntu kernel: [ 5.956218] ehci_hcd 0000:00:13.2: EHCI Host Controller Oct 30 11:56:22 ubuntu kernel: [ 5.956277] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 6 Oct 30 11:56:22 ubuntu kernel: [ 5.956343] ehci_hcd 0000:00:13.2: debug port 1 Oct 30 11:56:22 ubuntu kernel: [ 5.956396] ehci_hcd 0000:00:13.2: irq 19, io mem 0xfe029000 Oct 30 11:56:22 ubuntu kernel: [ 5.976019] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 Oct 30 11:56:22 ubuntu kernel: [ 5.976144] usb usb6: configuration #1 chosen from 1 choice Oct 30 11:56:22 ubuntu kernel: [ 5.976201] hub 6-0:1.0: USB hub found Oct 30 11:56:22 ubuntu kernel: [ 5.976238] hub 6-0:1.0: 6 ports detected Oct 30 11:56:22 ubuntu kernel: [ 6.185520] pata_acpi 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Oct 30 11:56:22 ubuntu kernel: [ 6.185659] ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Oct 30 11:56:22 ubuntu kernel: [ 6.185704] ohci_hcd 0000:00:14.5: OHCI Host Controller Oct 30 11:56:22 ubuntu kernel: [ 6.185771] ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 7 Oct 30 11:56:22 ubuntu kernel: [ 6.185821] ohci_hcd 0000:00:14.5: irq 18, io mem 0xfe028000 Oct 30 11:56:22 ubuntu kernel: [ 6.244801] usb usb7: configuration #1 chosen from 1 choice Oct 30 11:56:22 ubuntu kernel: [ 6.244864] hub 7-0:1.0: USB hub found Oct 30 11:56:22 ubuntu kernel: [ 6.244903] hub 7-0:1.0: 2 ports detected Oct 30 11:56:22 ubuntu kernel: [ 6.357707] scsi6 : pata_atiixp Oct 30 11:56:22 ubuntu kernel: [ 6.357807] scsi7 : pata_atiixp Oct 30 11:56:22 ubuntu kernel: [ 6.359019] ata7: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfa00 irq 14 Oct 30 11:56:22 ubuntu kernel: [ 6.359054] ata8: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfa08 irq 15 Oct 30 11:56:22 ubuntu kernel: [ 6.360814] scsi 0:0:0:0: Attached scsi generic sg0 type 0 Oct 30 11:56:22 ubuntu kernel: [ 6.360887] scsi 4:0:0:0: Attached scsi generic sg1 type 0 Oct 30 11:56:22 ubuntu kernel: [ 6.369529] usb 1-2: new low speed USB device using ohci_hcd and address 4 Oct 30 11:56:22 ubuntu kernel: [ 6.378333] Driver 'sd' needs updating - please use bus_type methods Oct 30 11:56:22 ubuntu kernel: [ 6.378478] sd 0:0:0:0: [sda] 1250263728 512-byte hardware sectors (640135 MB) Oct 30 11:56:22 ubuntu kernel: [ 6.378527] sd 0:0:0:0: [sda] Write Protect is off Oct 30 11:56:22 ubuntu kernel: [ 6.378561] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 Oct 30 11:56:22 ubuntu kernel: [ 6.378583] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Oct 30 11:56:22 ubuntu kernel: [ 6.378682] sd 0:0:0:0: [sda] 1250263728 512-byte hardware sectors (640135 MB) Oct 30 11:56:22 ubuntu kernel: [ 6.378730] sd 0:0:0:0: [sda] Write Protect is off Oct 30 11:56:22 ubuntu kernel: [ 6.378764] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 Oct 30 11:56:22 ubuntu kernel: [ 6.378785] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Oct 30 11:56:22 ubuntu kernel: [ 6.378826] sda: sda1 sda2 Oct 30 11:56:22 ubuntu kernel: [ 6.396744] sd 0:0:0:0: [sda] Attached SCSI disk Oct 30 11:56:22 ubuntu kernel: [ 6.396859] sd 4:0:0:0: [sdb] 1250263728 512-byte hardware sectors (640135 MB) Oct 30 11:56:22 ubuntu kernel: [ 6.396912] sd 4:0:0:0: [sdb] Write Protect is off Oct 30 11:56:22 ubuntu kernel: [ 6.396946] sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00 Oct 30 11:56:22 ubuntu kernel: [ 6.396978] sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Oct 30 11:56:22 ubuntu kernel: [ 6.397062] sd 4:0:0:0: [sdb] 1250263728 512-byte hardware sectors (640135 MB) Oct 30 11:56:22 ubuntu kernel: [ 6.397111] sd 4:0:0:0: [sdb] Write Protect is off Oct 30 11:56:22 ubuntu kernel: [ 6.397144] sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00 Oct 30 11:56:22 ubuntu kernel: [ 6.397167] sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Oct 30 11:56:22 ubuntu kernel: [ 6.397213] sdb: sdb1 sdb2 Oct 30 11:56:22 ubuntu kernel: [ 6.411444] sd 4:0:0:0: [sdb] Attached SCSI disk Oct 30 11:56:22 ubuntu kernel: [ 6.520501] ata7.00: ATAPI: TOSHIBA DVD-ROM SD-M1612, 1004, max UDMA/33 Oct 30 11:56:22 ubuntu kernel: [ 6.536460] ata7.00: configured for UDMA/33 Oct 30 11:56:22 ubuntu kernel: [ 6.537237] usb 1-2: configuration #1 chosen from 1 choice Oct 30 11:56:22 ubuntu kernel: [ 6.592082] usbcore: registered new interface driver hiddev Oct 30 11:56:22 ubuntu kernel: [ 6.598919] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:12.0/usb1/1-2/1-2:1.0/input/input2 Oct 30 11:56:22 ubuntu kernel: [ 6.626670] input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:12.0-2 Oct 30 11:56:22 ubuntu kernel: [ 6.626846] usbcore: registered new interface driver usbhid Oct 30 11:56:22 ubuntu kernel: [ 6.628416] usbhid: v2.6:USB HID core driver Oct 30 11:56:22 ubuntu kernel: [ 6.692121] isa bounce pool size: 16 pages Oct 30 11:56:22 ubuntu kernel: [ 6.693579] scsi 6:0:0:0: CD-ROM TOSHIBA DVD-ROM SD-M1612 1004 PQ: 0 ANSI: 5 Oct 30 11:56:22 ubuntu kernel: [ 6.693760] scsi 6:0:0:0: Attached scsi generic sg2 type 5 Oct 30 11:56:22 ubuntu kernel: [ 6.711730] Driver 'sr' needs updating - please use bus_type methods Oct 30 11:56:22 ubuntu kernel: [ 6.713140] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray Oct 30 11:56:22 ubuntu kernel: [ 6.713181] Uniform CD-ROM driver Revision: 3.20 Oct 30 11:56:22 ubuntu kernel: [ 6.713309] sr 6:0:0:0: Attached scsi CD-ROM sr0 Oct 30 11:56:22 ubuntu kernel: [ 6.865525] usb 5-3: new low speed USB device using ohci_hcd and address 2 Oct 30 11:56:22 ubuntu kernel: [ 7.048232] usb 5-3: configuration #1 chosen from 1 choice Oct 30 11:56:22 ubuntu kernel: [ 7.129318] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 7.129325] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 8.206526] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 8.206533] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 9.261160] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 9.261169] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 10.316918] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 10.316926] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 11.368748] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 11.368757] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 12.424444] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 12.424453] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 13.480339] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 13.480347] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 14.536525] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 14.536533] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 15.592624] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 15.592632] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 16.387170] sr 6:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK Oct 30 11:56:22 ubuntu kernel: [ 16.387241] sr 6:0:0:0: [sr0] Sense Key : Medium Error [current] Oct 30 11:56:22 ubuntu kernel: [ 16.387359] Info fld=0x56f36 Oct 30 11:56:22 ubuntu kernel: [ 16.387391] sr 6:0:0:0: [sr0] Add. Sense: CIRC unrecovered error Oct 30 11:56:22 ubuntu kernel: [ 16.387482] end_request: I/O error, dev sr0, sector 1424600 Oct 30 11:56:22 ubuntu kernel: [ 16.387518] Buffer I/O error on device sr0, logical block 356150 Oct 30 11:56:22 ubuntu kernel: [ 16.648494] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 16.648502] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 17.060535] /build/buildd/linux-2.6.27/drivers/hid/usbhid/hid-core.c: usb_submit_urb(ctrl) failed Oct 30 11:56:22 ubuntu kernel: [ 17.060586] usbhid: timeout initializing reports Oct 30 11:56:22 ubuntu kernel: [ 17.061269] input: Logitech Logitech Attack 3 as /devices/pci0000:00/0000:00:13.1/usb5/5-3/5-3:1.0/input/input3 Oct 30 11:56:22 ubuntu kernel: [ 17.061950] input,hidraw1: USB HID v1.10 Joystick [Logitech Logitech Attack 3] on usb-0000:00:13.1-3 Oct 30 11:56:22 ubuntu kernel: [ 17.700562] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 17.700570] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 17.910616] sr 6:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK Oct 30 11:56:22 ubuntu kernel: [ 17.910686] sr 6:0:0:0: [sr0] Sense Key : Medium Error [current] Oct 30 11:56:22 ubuntu kernel: [ 17.910805] Info fld=0x56f36 Oct 30 11:56:22 ubuntu kernel: [ 17.910837] sr 6:0:0:0: [sr0] Add. Sense: CIRC unrecovered error Oct 30 11:56:22 ubuntu kernel: [ 17.910928] end_request: I/O error, dev sr0, sector 1424600 Oct 30 11:56:22 ubuntu kernel: [ 17.910963] Buffer I/O error on device sr0, logical block 356150 Oct 30 11:56:22 ubuntu kernel: [ 18.752665] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 18.752673] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 19.434168] sr 6:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK Oct 30 11:56:22 ubuntu kernel: [ 19.434239] sr 6:0:0:0: [sr0] Sense Key : Medium Error [current] Oct 30 11:56:22 ubuntu kernel: [ 19.434357] Info fld=0x56f36 Oct 30 11:56:22 ubuntu kernel: [ 19.434389] sr 6:0:0:0: [sr0] Add. Sense: CIRC unrecovered error Oct 30 11:56:22 ubuntu kernel: [ 19.434480] end_request: I/O error, dev sr0, sector 1424600 Oct 30 11:56:22 ubuntu kernel: [ 19.434515] Buffer I/O error on device sr0, logical block 356150 Oct 30 11:56:22 ubuntu kernel: [ 19.808525] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 19.808534] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 20.864630] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 20.864638] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 20.957442] sr 6:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK Oct 30 11:56:22 ubuntu kernel: [ 20.957517] sr 6:0:0:0: [sr0] Sense Key : Medium Error [current] Oct 30 11:56:22 ubuntu kernel: [ 20.957636] Info fld=0x56f36 Oct 30 11:56:22 ubuntu kernel: [ 20.957668] sr 6:0:0:0: [sr0] Add. Sense: CIRC unrecovered error Oct 30 11:56:22 ubuntu kernel: [ 20.957760] end_request: I/O error, dev sr0, sector 1424600 Oct 30 11:56:22 ubuntu kernel: [ 20.957795] Buffer I/O error on device sr0, logical block 356150 Oct 30 11:56:22 ubuntu kernel: [ 21.920705] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 21.920713] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 22.480778] sr 6:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK Oct 30 11:56:22 ubuntu kernel: [ 22.480848] sr 6:0:0:0: [sr0] Sense Key : Medium Error [current] Oct 30 11:56:22 ubuntu kernel: [ 22.480967] Info fld=0x56f36 Oct 30 11:56:22 ubuntu kernel: [ 22.480999] sr 6:0:0:0: [sr0] Add. Sense: CIRC unrecovered error Oct 30 11:56:22 ubuntu kernel: [ 22.481090] end_request: I/O error, dev sr0, sector 1424600 Oct 30 11:56:22 ubuntu kernel: [ 22.481125] Buffer I/O error on device sr0, logical block 356150 Oct 30 11:56:22 ubuntu kernel: [ 22.976578] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 22.976586] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 24.004493] sr 6:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK Oct 30 11:56:22 ubuntu kernel: [ 24.004564] sr 6:0:0:0: [sr0] Sense Key : Medium Error [current] Oct 30 11:56:22 ubuntu kernel: [ 24.004683] Info fld=0x56f36 Oct 30 11:56:22 ubuntu kernel: [ 24.004715] sr 6:0:0:0: [sr0] Add. Sense: CIRC unrecovered error Oct 30 11:56:22 ubuntu kernel: [ 24.004806] end_request: I/O error, dev sr0, sector 1424600 Oct 30 11:56:22 ubuntu kernel: [ 24.004841] Buffer I/O error on device sr0, logical block 356150 Oct 30 11:56:22 ubuntu kernel: [ 24.032594] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 24.032602] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 25.084631] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 25.084639] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 25.527861] sr 6:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK Oct 30 11:56:22 ubuntu kernel: [ 25.527931] sr 6:0:0:0: [sr0] Sense Key : Medium Error [current] Oct 30 11:56:22 ubuntu kernel: [ 25.528050] Info fld=0x56f36 Oct 30 11:56:22 ubuntu kernel: [ 25.528082] sr 6:0:0:0: [sr0] Add. Sense: CIRC unrecovered error Oct 30 11:56:22 ubuntu kernel: [ 25.528173] end_request: I/O error, dev sr0, sector 1424600 Oct 30 11:56:22 ubuntu kernel: [ 25.528208] Buffer I/O error on device sr0, logical block 356150 Oct 30 11:56:22 ubuntu kernel: [ 26.140655] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 26.140662] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 26.971326] end_request: I/O error, dev sr0, sector 1424596 Oct 30 11:56:22 ubuntu kernel: [ 26.971366] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 27.196639] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 27.196646] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 28.252556] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 28.252564] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 28.498584] sr 6:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK Oct 30 11:56:22 ubuntu kernel: [ 28.498654] sr 6:0:0:0: [sr0] Sense Key : Medium Error [current] Oct 30 11:56:22 ubuntu kernel: [ 28.498773] Info fld=0x56f36 Oct 30 11:56:22 ubuntu kernel: [ 28.498805] sr 6:0:0:0: [sr0] Add. Sense: CIRC unrecovered error Oct 30 11:56:22 ubuntu kernel: [ 28.498896] end_request: I/O error, dev sr0, sector 1424600 Oct 30 11:56:22 ubuntu kernel: [ 28.498931] Buffer I/O error on device sr0, logical block 356150 Oct 30 11:56:22 ubuntu kernel: [ 29.308761] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 29.308768] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 30.021792] sr 6:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK Oct 30 11:56:22 ubuntu kernel: [ 30.021863] sr 6:0:0:0: [sr0] Sense Key : Medium Error [current] Oct 30 11:56:22 ubuntu kernel: [ 30.021981] Info fld=0x56f36 Oct 30 11:56:22 ubuntu kernel: [ 30.022013] sr 6:0:0:0: [sr0] Add. Sense: CIRC unrecovered error Oct 30 11:56:22 ubuntu kernel: [ 30.022104] end_request: I/O error, dev sr0, sector 1424600 Oct 30 11:56:22 ubuntu kernel: [ 30.022139] Buffer I/O error on device sr0, logical block 356150 Oct 30 11:56:22 ubuntu kernel: [ 30.364639] kjournald starting. Commit interval 5 seconds Oct 30 11:56:22 ubuntu kernel: [ 30.364647] EXT3-fs: mounted filesystem with ordered data mode. Oct 30 11:56:22 ubuntu kernel: [ 32.370277] end_request: I/O error, dev sr0, sector 1424592 Oct 30 11:56:22 ubuntu kernel: [ 32.370316] Buffer I/O error on device sr0, logical block 178074 Oct 30 11:56:22 ubuntu kernel: [ 33.512916] end_request: I/O error, dev sr0, sector 1424592 Oct 30 11:56:22 ubuntu kernel: [ 33.512950] Buffer I/O error on device sr0, logical block 178074 Oct 30 11:56:22 ubuntu kernel: [ 34.655424] end_request: I/O error, dev sr0, sector 1424592 Oct 30 11:56:22 ubuntu kernel: [ 34.655464] Buffer I/O error on device sr0, logical block 178074 Oct 30 11:56:22 ubuntu kernel: [ 36.266407] end_request: I/O error, dev sr0, sector 1424592 Oct 30 11:56:22 ubuntu kernel: [ 36.266445] Buffer I/O error on device sr0, logical block 178074 Oct 30 11:56:22 ubuntu kernel: [ 37.408952] end_request: I/O error, dev sr0, sector 1424592 Oct 30 11:56:22 ubuntu kernel: [ 37.408986] Buffer I/O error on device sr0, logical block 178074 Oct 30 11:56:22 ubuntu kernel: [ 38.551605] end_request: I/O error, dev sr0, sector 1424592 Oct 30 11:56:22 ubuntu kernel: [ 38.551639] Buffer I/O error on device sr0, logical block 178074 Oct 30 11:56:22 ubuntu kernel: [ 39.694090] end_request: I/O error, dev sr0, sector 1424592 Oct 30 11:56:22 ubuntu kernel: [ 39.694125] Buffer I/O error on device sr0, logical block 178074 Oct 30 11:56:22 ubuntu kernel: [ 41.065373] end_request: I/O error, dev sr0, sector 1424592 Oct 30 11:56:22 ubuntu kernel: [ 41.065412] Buffer I/O error on device sr0, logical block 178074 Oct 30 11:56:22 ubuntu kernel: [ 42.207776] end_request: I/O error, dev sr0, sector 1424592 Oct 30 11:56:22 ubuntu kernel: [ 42.207813] Buffer I/O error on device sr0, logical block 178074 Oct 30 11:56:22 ubuntu kernel: [ 42.634991] ISO 9660 Extensions: Microsoft Joliet Level 3 Oct 30 11:56:22 ubuntu kernel: [ 42.726718] ISO 9660 Extensions: RRIP_1991A Oct 30 11:56:22 ubuntu kernel: [ 43.064635] aufs 20080922 Oct 30 11:56:22 ubuntu kernel: [ 43.080066] loop: module loaded Oct 30 11:56:22 ubuntu kernel: [ 43.353926] squashfs: version 3.3 (2007/10/31) Phillip Lougher Oct 30 11:56:22 ubuntu kernel: [ 78.281197] end_request: I/O error, dev sr0, sector 1424592 Oct 30 11:56:22 ubuntu kernel: [ 78.281236] Buffer I/O error on device sr0, logical block 356148 Oct 30 11:56:22 ubuntu kernel: [ 78.281272] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 79.330520] end_request: I/O error, dev sr0, sector 1424592 Oct 30 11:56:22 ubuntu kernel: [ 79.330554] Buffer I/O error on device sr0, logical block 356148 Oct 30 11:56:22 ubuntu kernel: [ 79.330589] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 80.386837] end_request: I/O error, dev sr0, sector 1424596 Oct 30 11:56:22 ubuntu kernel: [ 80.386871] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 81.445971] end_request: I/O error, dev sr0, sector 1424596 Oct 30 11:56:22 ubuntu kernel: [ 81.446005] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 82.501106] end_request: I/O error, dev sr0, sector 1424596 Oct 30 11:56:22 ubuntu kernel: [ 82.501140] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 83.555735] end_request: I/O error, dev sr0, sector 1424596 Oct 30 11:56:22 ubuntu kernel: [ 83.555770] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 84.610329] end_request: I/O error, dev sr0, sector 1424596 Oct 30 11:56:22 ubuntu kernel: [ 84.610364] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 85.709070] end_request: I/O error, dev sr0, sector 1424596 Oct 30 11:56:22 ubuntu kernel: [ 85.709104] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 86.764132] end_request: I/O error, dev sr0, sector 1424596 Oct 30 11:56:22 ubuntu kernel: [ 86.764166] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 101.409558] udevd version 124 started Oct 30 11:56:22 ubuntu kernel: [ 101.620362] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 Oct 30 11:56:22 ubuntu kernel: [ 101.640155] shpchp: HPC vendor_id 1022 device_id 9602 ss_vid 0 ss_did 0 Oct 30 11:56:22 ubuntu kernel: [ 101.640198] shpchp: shpc_init: cannot reserve MMIO region Oct 30 11:56:22 ubuntu kernel: [ 101.640267] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 Oct 30 11:56:22 ubuntu kernel: [ 102.258483] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4 Oct 30 11:56:22 ubuntu kernel: [ 102.286271] ACPI: Power Button (FF) [PWRF] Oct 30 11:56:22 ubuntu kernel: [ 102.286396] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5 Oct 30 11:56:22 ubuntu kernel: [ 102.317518] ACPI: Power Button (CM) [PWRB] Oct 30 11:56:22 ubuntu kernel: [ 102.430904] ACPI: WMI: Mapper loaded Oct 30 11:56:22 ubuntu kernel: [ 102.560073] ACPI: I/O resource piix4_smbus [0xb00-0xb07] conflicts with ACPI region SOR1 [0xb00-0xb0f] Oct 30 11:56:22 ubuntu kernel: [ 102.560118] ACPI: Device needs an ACPI driver Oct 30 11:56:22 ubuntu kernel: [ 102.560157] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0 Oct 30 11:56:22 ubuntu kernel: [ 102.632996] input: PC Speaker as /devices/platform/pcspkr/input/input6 Oct 30 11:56:22 ubuntu kernel: [ 103.087266] HDA Intel 0000:01:05.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 Oct 30 11:56:22 ubuntu kernel: [ 103.087322] HDA Intel 0000:01:05.1: setting latency timer to 64 Oct 30 11:56:22 ubuntu kernel: [ 103.168020] ICE1724 0000:03:07.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 Oct 30 11:56:22 ubuntu kernel: [ 105.036098] end_request: I/O error, dev sr0, sector 1424596 Oct 30 11:56:22 ubuntu kernel: [ 105.036138] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 106.082883] end_request: I/O error, dev sr0, sector 1424596 Oct 30 11:56:22 ubuntu kernel: [ 106.082918] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 107.129050] end_request: I/O error, dev sr0, sector 1424596 Oct 30 11:56:22 ubuntu kernel: [ 107.129084] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 108.184385] end_request: I/O error, dev sr0, sector 1424596 Oct 30 11:56:22 ubuntu kernel: [ 108.184426] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 109.238009] end_request: I/O error, dev sr0, sector 1424596 Oct 30 11:56:22 ubuntu kernel: [ 109.238048] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 110.294095] end_request: I/O error, dev sr0, sector 1424596 Oct 30 11:56:22 ubuntu kernel: [ 110.294134] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 111.346913] end_request: I/O error, dev sr0, sector 1424596 Oct 30 11:56:22 ubuntu kernel: [ 111.346952] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 112.403820] end_request: I/O error, dev sr0, sector 1424596 Oct 30 11:56:22 ubuntu kernel: [ 112.403855] Buffer I/O error on device sr0, logical block 356149 Oct 30 11:56:22 ubuntu kernel: [ 113.845253] Adding 979924k swap on /dev/sdb1. Priority:-1 extents:1 across:979924k Oct 30 11:56:22 ubuntu kernel: [ 114.448536] ip_tables: (C) 2000-2006 Netfilter Core Team Oct 30 11:56:22 ubuntu kernel: [ 117.704475] powernow-k8: Found 1 AMD Phenom(tm) 9350e Quad-Core Processor processors (4 cpu cores) (version 2.20.00) Oct 30 11:56:22 ubuntu kernel: [ 117.704517] powernow-k8: 0 : pstate 0 (2000 MHz) Oct 30 11:56:22 ubuntu kernel: [ 117.704520] powernow-k8: 1 : pstate 1 (1000 MHz) Oct 30 11:56:22 ubuntu avahi-daemon[8891]: Found user 'avahi' (UID 106) and group 'avahi' (GID 116). Oct 30 11:56:22 ubuntu avahi-daemon[8891]: Successfully dropped root privileges. Oct 30 11:56:22 ubuntu kernel: [ 119.105230] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use) Oct 30 11:56:22 ubuntu avahi-daemon[8891]: avahi-daemon 0.6.23 starting up. Oct 30 11:56:22 ubuntu avahi-daemon[8891]: Successfully called chroot(). Oct 30 11:56:22 ubuntu avahi-daemon[8891]: Successfully dropped remaining capabilities. Oct 30 11:56:22 ubuntu avahi-daemon[8892]: chroot.c: open() failed: No such file or directory Oct 30 11:56:22 ubuntu avahi-daemon[8891]: Failed to open /etc/resolv.conf: Invalid argument Oct 30 11:56:22 ubuntu avahi-daemon[8891]: No service file found in /etc/avahi/services. Oct 30 11:56:22 ubuntu avahi-daemon[8891]: Network interface enumeration completed. Oct 30 11:56:22 ubuntu avahi-daemon[8891]: Registering HINFO record with values 'X86_64'/'LINUX'. Oct 30 11:56:22 ubuntu avahi-daemon[8891]: Server startup complete. Host name is ubuntu.local. Local service cookie is 3354321440. Oct 30 11:56:23 ubuntu kernel: [ 119.265599] lp: driver loaded but no devices found Oct 30 11:56:23 ubuntu kernel: [ 119.421542] ppdev: user-space parallel port driver Oct 30 11:56:29 ubuntu acpid: client connected from 9102[108:118] Oct 30 11:56:30 ubuntu bluetoothd[9151]: Bluetooth daemon Oct 30 11:56:30 ubuntu kernel: [ 127.010844] Bluetooth: Core ver 2.13 Oct 30 11:56:30 ubuntu kernel: [ 127.010972] NET: Registered protocol family 31 Oct 30 11:56:30 ubuntu kernel: [ 127.010977] Bluetooth: HCI device and connection manager initialized Oct 30 11:56:30 ubuntu kernel: [ 127.010982] Bluetooth: HCI socket layer initialized Oct 30 11:56:30 ubuntu bluetoothd[9151]: Starting SDP server Oct 30 11:56:30 ubuntu kernel: [ 127.072205] Bluetooth: L2CAP ver 2.11 Oct 30 11:56:30 ubuntu kernel: [ 127.072215] Bluetooth: L2CAP socket layer initialized Oct 30 11:56:31 ubuntu kernel: [ 127.271473] Bluetooth: SCO (Voice Link) ver 0.6 Oct 30 11:56:31 ubuntu kernel: [ 127.271486] Bluetooth: SCO socket layer initialized Oct 30 11:56:31 ubuntu bluetoothd[9151]: Starting experimental netlink support Oct 30 11:56:31 ubuntu bluetoothd[9151]: Failed to find Bluetooth netlink family Oct 30 11:56:31 ubuntu bluetoothd[9151]: Can't init plugin /usr/lib/bluetooth/plugins/netlink.so Oct 30 11:56:31 ubuntu kernel: [ 127.611788] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Oct 30 11:56:31 ubuntu kernel: [ 127.611799] Bluetooth: BNEP filters: protocol multicast Oct 30 11:56:31 ubuntu kernel: [ 127.619449] Bluetooth: RFCOMM socket layer initialized Oct 30 11:56:31 ubuntu kernel: [ 127.619477] Bluetooth: RFCOMM TTY layer initialized Oct 30 11:56:31 ubuntu kernel: [ 127.619480] Bluetooth: RFCOMM ver 1.10 Oct 30 11:56:31 ubuntu kernel: [ 127.741941] Bridge firewalling registered Oct 30 11:56:31 ubuntu bluetoothd[9151]: bridge pan0 created Oct 30 11:56:31 ubuntu kernel: [ 127.742246] pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature. Oct 30 11:56:32 ubuntu NetworkManager: <info> starting... Oct 30 11:56:32 ubuntu NetworkManager: <info> eth0: driver is 'r8169'. Oct 30 11:56:32 ubuntu NetworkManager: <info> Found new Ethernet device 'eth0'. Oct 30 11:56:32 ubuntu NetworkManager: <info> (eth0): exported as /org/freedesktop/Hal/devices/net_00_1f_d0_56_5e_a0 Oct 30 11:56:32 ubuntu NetworkManager: <info> Trying to start the supplicant... Oct 30 11:56:32 ubuntu NetworkManager: <info> Trying to start the system settings daemon... Oct 30 11:56:32 ubuntu nm-system-settings: SCPlugin-Ifupdown: init! Oct 30 11:56:32 ubuntu nm-system-settings: SCPlugin-Ifupdown: update_system_hostname Oct 30 11:56:32 ubuntu nm-system-settings: SCPluginIfupdown: management mode: unmanaged Oct 30 11:56:32 ubuntu nm-system-settings: SCPlugin-Ifupdown: devices added (udi: /org/freedesktop/Hal/devices/net_00_1f_d0_56_5e_a0, iface: eth0) Oct 30 11:56:32 ubuntu nm-system-settings: SCPlugin-Ifupdown: end _init. Oct 30 11:56:32 ubuntu nm-system-settings: Loaded plugin ifupdown: (C) 2008 Canonical Ltd. To report bugs please use the NetworkManager mailing list. Oct 30 11:56:33 ubuntu nm-system-settings: Loaded plugin keyfile: (c) 2007 - 2008 Red Hat, Inc. To report bugs please use the NetworkManager mailing list. Oct 30 11:56:33 ubuntu nm-system-settings: SCPlugin-Ifupdown: (16266432) ... get_connections. Oct 30 11:56:33 ubuntu nm-system-settings: SCPlugin-Ifupdown: (16266432) connections count: 0 Oct 30 11:56:33 ubuntu nm-system-settings: Ifupdown: get unmanaged devices count: 0 Oct 30 11:56:34 ubuntu /usr/sbin/cron[9282]: (CRON) INFO (pidfile fd = 3) Oct 30 11:56:34 ubuntu /usr/sbin/cron[9283]: (CRON) STARTUP (fork ok) Oct 30 11:56:34 ubuntu /usr/sbin/cron[9283]: (CRON) INFO (Running @reboot jobs) Oct 30 11:56:34 ubuntu acpid: client connected from 9242[0:0] Oct 30 11:56:35 ubuntu kernel: [ 132.041826] pci 0000:01:05.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Oct 30 11:56:36 ubuntu NetworkManager: <info> (eth0): device state change: 1 -> 2 Oct 30 11:56:36 ubuntu NetworkManager: <info> (eth0): bringing up device. Oct 30 11:56:36 ubuntu kernel: [ 132.328550] r8169: eth0: link up Oct 30 11:56:36 ubuntu kernel: [ 132.328569] r8169: eth0: link up Oct 30 11:56:36 ubuntu NetworkManager: <info> (eth0): preparing device. Oct 30 11:56:36 ubuntu NetworkManager: <info> (eth0): deactivating device (reason: 2). Oct 30 11:56:36 ubuntu NetworkManager: <info> (eth0): carrier now ON (device state 2) Oct 30 11:56:36 ubuntu NetworkManager: <info> (eth0): device state change: 2 -> 3 Oct 30 11:56:37 ubuntu nm-system-settings: Adding default connection 'Auto eth0' for /org/freedesktop/Hal/devices/net_00_1f_d0_56_5e_a0 Oct 30 11:56:37 ubuntu NetworkManager: <info> Activation (eth0) starting connection 'Auto eth0' Oct 30 11:56:37 ubuntu NetworkManager: <info> (eth0): device state change: 3 -> 4 Oct 30 11:56:37 ubuntu NetworkManager: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Oct 30 11:56:37 ubuntu NetworkManager: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Oct 30 11:56:37 ubuntu NetworkManager: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Oct 30 11:56:37 ubuntu NetworkManager: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Oct 30 11:56:37 ubuntu NetworkManager: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Oct 30 11:56:37 ubuntu NetworkManager: <info> (eth0): device state change: 4 -> 5 Oct 30 11:56:37 ubuntu NetworkManager: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Oct 30 11:56:37 ubuntu NetworkManager: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Oct 30 11:56:37 ubuntu NetworkManager: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Oct 30 11:56:37 ubuntu NetworkManager: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Oct 30 11:56:37 ubuntu NetworkManager: <info> (eth0): device state change: 5 -> 7 Oct 30 11:56:37 ubuntu NetworkManager: <info> Activation (eth0) Beginning DHCP transaction. Oct 30 11:56:37 ubuntu NetworkManager: <info> dhclient started with pid 9385 Oct 30 11:56:37 ubuntu NetworkManager: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Oct 30 11:56:37 ubuntu dhclient: Internet Systems Consortium DHCP Client V3.1.1 Oct 30 11:56:37 ubuntu dhclient: Copyright 2004-2008 Internet Systems Consortium. Oct 30 11:56:37 ubuntu dhclient: All rights reserved. Oct 30 11:56:37 ubuntu dhclient: For info, please visit http://www.isc.org/sw/dhcp/ Oct 30 11:56:37 ubuntu dhclient: Oct 30 11:56:37 ubuntu NetworkManager: <info> DHCP: device eth0 state changed (null) -> preinit Oct 30 11:56:37 ubuntu kernel: [ 133.897082] NET: Registered protocol family 17 Oct 30 11:56:37 ubuntu dhclient: Listening on LPF/eth0/00:1f:d0:56:5e:a0 Oct 30 11:56:37 ubuntu dhclient: Sending on LPF/eth0/00:1f:d0:56:5e:a0 Oct 30 11:56:37 ubuntu dhclient: Sending on Socket/fallback Oct 30 11:56:38 ubuntu dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 Oct 30 11:56:38 ubuntu dhclient: DHCPOFFER of 192.168.1.186 from 192.168.1.1 Oct 30 11:56:38 ubuntu dhclient: DHCPREQUEST of 192.168.1.186 on eth0 to 255.255.255.255 port 67 Oct 30 11:56:38 ubuntu dhclient: DHCPACK of 192.168.1.186 from 192.168.1.1 Oct 30 11:56:38 ubuntu NetworkManager: <info> DHCP: device eth0 state changed preinit -> bound Oct 30 11:56:38 ubuntu NetworkManager: <info> Activation (eth0) Stage 4 of 5 (IP Configure Get) scheduled... Oct 30 11:56:38 ubuntu dhclient: bound to 192.168.1.186 -- renewal in 41357 seconds. Oct 30 11:56:38 ubuntu NetworkManager: <info> Activation (eth0) Stage 4 of 5 (IP Configure Get) started... Oct 30 11:56:38 ubuntu NetworkManager: <info> address 192.168.1.186 Oct 30 11:56:38 ubuntu NetworkManager: <info> prefix 24 (255.255.255.0) Oct 30 11:56:38 ubuntu NetworkManager: <info> gateway 192.168.1.1 Oct 30 11:56:38 ubuntu NetworkManager: <info> nameserver '192.168.1.1' Oct 30 11:56:38 ubuntu NetworkManager: <info> domain name 'netz' Oct 30 11:56:38 ubuntu NetworkManager: <info> Activation (eth0) Stage 5 of 5 (IP Configure Commit) scheduled... Oct 30 11:56:38 ubuntu NetworkManager: <info> Activation (eth0) Stage 4 of 5 (IP Configure Get) complete. Oct 30 11:56:38 ubuntu NetworkManager: <info> Activation (eth0) Stage 5 of 5 (IP Configure Commit) started... Oct 30 11:56:38 ubuntu avahi-daemon[8891]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.1.186. Oct 30 11:56:38 ubuntu avahi-daemon[8891]: New relevant interface eth0.IPv4 for mDNS. Oct 30 11:56:38 ubuntu avahi-daemon[8891]: Registering new address record for 192.168.1.186 on eth0.IPv4. Oct 30 11:56:39 ubuntu NetworkManager: <info> (eth0): device state change: 7 -> 8 Oct 30 11:56:39 ubuntu NetworkManager: <info> Policy set 'Auto eth0' (eth0) as default for routing and DNS. Oct 30 11:56:39 ubuntu NetworkManager: <info> Activation (eth0) successful, device activated. Oct 30 11:56:39 ubuntu NetworkManager: <info> Activation (eth0) Stage 5 of 5 (IP Configure Commit) complete. Oct 30 10:56:41 ubuntu ntpdate[9488]: step time server 91.189.94.4 offset -3599.930487 sec Oct 30 10:57:45 ubuntu python: hp-systray(init)[9904]: warning: No hp: or hpfax: devices found in any installed CUPS queue. Exiting. Oct 30 10:58:26 ubuntu NetworkManager: <WARN> list_connections_cb(): Couldn't retrieve connections: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken.. Oct 30 10:59:22 ubuntu kernel: [ 298.928588] kjournald starting. Commit interval 5 seconds Oct 30 10:59:22 ubuntu kernel: [ 298.928754] EXT3 FS on sda1, internal journal Oct 30 10:59:22 ubuntu kernel: [ 298.928766] EXT3-fs: mounted filesystem with ordered data mode. lspci -vv: 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge Subsystem: Advanced Micro Devices [AMD] RS780 Host Bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 32 Region 3: Memory at <ignored> (64-bit, non-prefetchable) Capabilities: [c4] HyperTransport: Slave or Primary Interface Command: BaseUnitID=0 UnitCnt=12 MastHost- DefDir- DUL- Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- Revision ID: 3.00 Link Frequency 0: [a] Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- Link Frequency 1: 200MHz Link Error 1: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- Prefetchable memory behind bridge Upper: 00-00 Bus Number: 00 Capabilities: [54] HyperTransport: UnitID Clumping Capabilities: [40] HyperTransport: Retry Mode Capabilities: [9c] HyperTransport: #1a Capabilities: [f8] HyperTransport: #1c 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 99 Bus: primary=00, secondary=01, subordinate=01, sec-latency=68 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fdd00000-fdefffff Prefetchable memory behind bridge: 00000000d8000000-00000000dfffffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [44] HyperTransport: MSI Mapping Enable+ Fixed+ Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) Kernel modules: shpchp 00:0a.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 5) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fda00000-fdafffff Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep+ BwNot+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- Slot # a, PowerLimit 25.000000; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0f00c Data: 4151 Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 9600 Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Capabilities: [100] Vendor Specific Information <?> Capabilities: [110] Virtual Channel <?> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] (prog-if 01) Subsystem: Giga-byte Technology Device b002 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 2301 Region 0: I/O ports at ff00 [size=8] Region 1: I/O ports at fe00 [size=4] Region 2: I/O ports at fd00 [size=8] Region 3: I/O ports at fc00 [size=4] Region 4: I/O ports at fb00 [size=16] Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable+ Address: 00000000fee0f00c Data: 4171 Capabilities: [70] SATA HBA <?> Kernel driver in use: ahci Kernel modules: ahci 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller (prog-if 10) Subsystem: Giga-byte Technology Device 5004 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller (prog-if 10) Subsystem: Giga-byte Technology Device 5004 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller (prog-if 20) Subsystem: Giga-byte Technology Device 5004 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 17 Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [e4] Debug port: BAR=1 offset=00e0 Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller (prog-if 10) Subsystem: Giga-byte Technology Device 5004 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller (prog-if 10) Subsystem: Giga-byte Technology Device 5004 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller (prog-if 20) Subsystem: Giga-byte Technology Device 5004 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 19 Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [e4] Debug port: BAR=1 offset=00e0 Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3a) Subsystem: Giga-byte Technology Device 4385 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: piix4_smbus Kernel modules: i2c-piix4 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller (prog-if 8a [Master SecP PriP]) Subsystem: Giga-byte Technology Device 5002 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at fa00 [size=16] Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 Kernel driver in use: pata_atiixp Kernel modules: ata_generic, pata_acpi, pata_atiixp 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller Subsystem: ATI Technologies Inc Device 4383 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (prog-if 01) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Bus: primary=00, secondary=03, subordinate=03, sec-latency=64 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fdc00000-fdcfffff Prefetchable memory behind bridge: fdb00000-fdbfffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller (prog-if 10) Subsystem: Giga-byte Technology Device 5004 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin C routed to IRQ 18 Region 0: Memory at fe028000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] HyperTransport Configuration Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [80] HyperTransport: Host or Secondary Interface Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b- Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Revision ID: 3.00 Link Frequency: [a] Link Error: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE- 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Address Map Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] DRAM Controller Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Miscellaneous Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [f0] Secure device <?> 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h [Opteron, Athlon64, Sempron] Link Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon HD 3200 Graphics Subsystem: Giga-byte Technology Device d000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at ee00 [size=256] Region 2: Memory at fdee0000 (32-bit, non-prefetchable) [size=64K] Region 5: Memory at fdd00000 (32-bit, non-prefetchable) [size=1M] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Kernel driver in use: fglrx_pci Kernel modules: fglrx 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller Subsystem: ATI Technologies Inc RS780 Azalia controller Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin B routed to IRQ 5 Region 0: Memory at fdefc000 (32-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) Subsystem: Giga-byte Technology Device e000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 2302 Region 0: I/O ports at de00 [size=256] Region 2: Memory at fdfff000 (64-bit, prefetchable) [size=4K] Region 4: Memory at fdfe0000 (64-bit, prefetchable) [size=64K] [virtual] Expansion ROM at fdf00000 [disabled] [size=64K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+ Address: 00000000fee0f00c Data: 4159 Capabilities: [70] Express (v1) Endpoint, MSI 01 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <8us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us ClockPM+ Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [b0] MSI-X: Enable- Mask- TabSize=2 Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00000800 Capabilities: [d0] Vital Product Data <?> Capabilities: [100] Advanced Error Reporting <?> Capabilities: [140] Virtual Channel <?> Capabilities: [160] Device Serial Number 78-56-34-12-78-56-34-12 Kernel driver in use: r8169 Kernel modules: r8169 03:07.0 Multimedia audio controller: VIA Technologies Inc. VT1720/24 [Envy24PT/HT] PCI Multi-Channel Audio Controller (rev 01) Subsystem: VIA Technologies Inc. Device 3630 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 Interrupt: pin A routed to IRQ 21 Region 0: I/O ports at cf00 [size=32] Region 1: I/O ports at ce00 [size=128] Capabilities: [80] Power Management version 1 Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ICE1724 Kernel modules: snd-ice1724

3 2

Re: [alsa-devel] State of the XFi driver on x86_64
by Toby 03 Nov '08

03 Nov '08

2008/11/3 Takashi Iwai <tiwai(a)suse.de>: > At Mon, 3 Nov 2008 10:42:55 +1100, > Toby wrote: >> >> 2008/11/2 WILMES Andreas <administrator(a)webspace.ms>: >> > Hello everbody, >> > >> > Can someone give the current state of the driver? What are his features, >> > what is working? >> >> I've been watching this thread for a while, and occasionally trying >> out new builds, as I have an original PCI X-Fi emu20k1. >> Everyone else seems to be reporting decent successes, but I have never >> managed it myself. >> >> Playing back sound files at any sample-rate results in a repeating >> burst of static. Adjusting the period/buffer parameters to aplay will >> cause the pitch/tone of the static burst to change, but never turn >> into anything remotely like the desired sound. >> >> I'm running this on a 64-bit system (Ubuntu 8.04 with a custom >> compiled kernel). Is anyone else having success on this platform? > > Maybe the difference of SB X-Fi model? > > IIRC, the boards people reported to work are either the original X-Fi, > SB055x or SB077x model. Is yours Vista-compatible one? > It appears in /proc/asound/cards as UAA, and can be identified via PCI > SSID. I believe I have the original model, as I bought this card shortly after the X-Fi was first announced. According to lspci: 05:02.0 Multimedia audio controller [0401]: Creative Labs SB X-Fi [1102:0005] Subsystem: Creative Labs X-Fi Platinum [1102:0021] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (1000ns min, 1250ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at d000 [size=32] Region 1: Memory at fb000000 (64-bit, non-prefetchable) [size=2M] Region 3: Memory at fb200000 (64-bit, non-prefetchable) [size=2M] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Some dmesg output: [ 245.518854] SBXFI: Allocate SRC 0 [ 245.537647] SBXFI: allocated TLB at 0 for 16 pages [ 245.537650] SBXFI: Setting TLB buffer page 0x7f9ea000 [ 245.538174] SBXFI: PLAYBACK PREPARE: rate=48000, period_size=4096, buffer_size=16384 [ 245.538177] SBXFI: Pitch [0:fa6] = 0x1000000 [ 245.538180] SBXFI: Pitch [1:fb6] = 0x1000000 [ 245.538183] SBXFI: Amp [00:0001] = 0x7b6 [ 245.538188] SBXFI: Amp [01:0011] = 0x7b6 [ 245.545546] SBXFI: PLAY TRIGGER START [ 245.545550] SBXFI: SETUP SRC: ch=0x0, start=0x0, loop=0x10000, cache=0x100, ctrl=0x1044c [ 245.545563] SBXFI: SETUP SRC: ch=0x1, start=0x0, loop=0x10000, cache=0x100, ctrl=0x4c [ 245.545578] SBXFI: PLAY UPDATE TIMER [ 246.996338] SBXFI: PLAY TRIGGER STOP [ 246.996352] SBXFI: PLAY UPDATE TIMER [ 246.996782] SBXFI: release TLB at 0 for 16 pages [ 246.996785] SBXFI: Disabling TLB buffer [ 246.997359] SBXFI: Release SRC 0 How could I help debug this? -- Turning and turning in the widening gyre The falcon cannot hear the falconer Things fall apart; the center cannot hold Mere anarchy is loosed upon the world

1 0

[alsa-devel] [PATCH] Fix PIT lockup on some chipsets when using the PC-Speaker
by Zoltan Devai 03 Nov '08

03 Nov '08

Hi, There've been reports [1] about the sysem bell causing a hard lockup. My machine was affected as well: Any speaker output hung the machine completely, nothing in the logs, no magic sysrq, etc., looked like a hardware problem. Had a closer look on the issue, and it turned out that the pcspkr module is responsible. The cause is the bad setup of Timer 2 in the i8253 controller, which probably hangs the whole PIT controller. Intel datasheets [2] state that the timer registers are in an undefined state after reset and they need to be programmed before enabling the timer. (And enabling without programming the frequency first doesn't make sense anyway). I don't know which chipsets are affected (if not all), it also depends on the BIOS whether it initializes the timer (e.g. to beep when you start the machine). The following patch solved the issue on my ICH6 notebook, couldn't test it with any others, but should be safe to apply. I've also sent a patch to the linux-input list for the pcspkr module. [1] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/146151 https://bugs.launchpad.net/ubuntu/+bug/270790 http://ubuntuforums.org/showthread.php?t=227693 http://bugs.gentoo.org/show_bug.cgi?id=222583 https://bugzilla.redhat.com/show_bug.cgi?id=454225 [2] http://www.intel.com/assets/pdf/datasheet/252516.pdf http://www.intel.com/assets/pdf/datasheet/301473.pdf http://www.intel.com/design/chipsets/datashts/29065503.pdf ------------------ Fix PIT lockup on some chipsets when using the PC-Speaker. Signed-off-by: Zoltan Devai <zdevai(a)gmail.com> --- a/sound/drivers/pcsp/pcsp_input.c +++ b/sound/drivers/pcsp/pcsp_input.c @@ -24,13 +24,13 @@ spin_lock_irqsave(&i8253_lock, flags); if (count) { - /* enable counter 2 */ - outb_p(inb_p(0x61) | 3, 0x61); /* set command for counter 2, 2 byte write */ outb_p(0xB6, 0x43); /* select desired HZ */ outb_p(count & 0xff, 0x42); outb((count >> 8) & 0xff, 0x42); + /* enable counter 2 */ + outb_p(inb_p(0x61) | 3, 0x61); } else { /* disable counter 2 */ outb(inb_p(0x61) & 0xFC, 0x61);

2 1

Re: [alsa-devel] State of the XFi driver on x86_64
by Toby 03 Nov '08

03 Nov '08

2008/11/2 WILMES Andreas <administrator(a)webspace.ms>: > Hello everbody, > > Can someone give the current state of the driver? What are his features, > what is working? I've been watching this thread for a while, and occasionally trying out new builds, as I have an original PCI X-Fi emu20k1. Everyone else seems to be reporting decent successes, but I have never managed it myself. Playing back sound files at any sample-rate results in a repeating burst of static. Adjusting the period/buffer parameters to aplay will cause the pitch/tone of the static burst to change, but never turn into anything remotely like the desired sound. I'm running this on a 64-bit system (Ubuntu 8.04 with a custom compiled kernel). Is anyone else having success on this platform? Thanks, Toby -- Turning and turning in the widening gyre The falcon cannot hear the falconer Things fall apart; the center cannot hold Mere anarchy is loosed upon the world

3 3

[alsa-devel] M2N68-VM - No digital sound
by Ben Matthews 02 Nov '08

02 Nov '08

Hey Guys, I have the asus m2n68-vm motherboard currently have analog sound but no HDMI audio or digial audio. The subdevice 1043:8345 appears to be the problem, in windows HDMI sound works, and digial outputs are present. Chip VT1708B Chipset 630a see http://www.alsa-project.org/db/?f=37aec7ec77f7bd421ac7933702a5975e5764871f for more information. Any help would be wonderful happy to test / supply more information as required thanks, Ben.

1 0

[alsa-devel] sound-unstable-snapshot doesn't compile
by Vedran Miletić 02 Nov '08

02 Nov '08

I get this error: CC [M] /home/vedran/bin/alsa-driver-unstable/soc/soc-core.o In file included from /home/vedran/bin/alsa-driver-unstable/soc/soc-core.c:6: /home/vedran/bin/alsa-driver-unstable/soc/../alsa-kernel/soc/soc-core.c: In function 'soc_init_debugfs': /home/vedran/bin/alsa-driver-unstable/soc/../alsa-kernel/soc/soc-core.c:1075: error: implicit declaration of function 'debugfs_remove_recursive' make[3]: *** [/home/vedran/bin/alsa-driver-unstable/soc/soc-core.o] Error 1 make[2]: *** [/home/vedran/bin/alsa-driver-unstable/soc] Error 2 make[1]: *** [_module_/home/vedran/bin/alsa-driver-unstable] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.26-1-amd64' make: *** [compile] Error 2 Linux kalopsia 2.6.26-1-amd64 #1 SMP Thu Oct 9 14:16:53 UTC 2008 x86_64 GNU/Linux -- Vedran Miletić

3 4