[alsa-devel] Gigabyte ALC889A Function ID: 0x01
Takashi Iwai
tiwai at suse.de
Wed Apr 15 17:17:28 CEST 2009
At Wed, 15 Apr 2009 11:14:20 -0400,
Jerry Geis wrote:
>
>
>
> Takashi Iwai wrote:
> > At Wed, 15 Apr 2009 10:45:43 -0400,
> > Jerry Geis wrote:
> >
> >> Takashi Iwai wrote:
> >>
> >>> At Wed, 15 Apr 2009 10:00:33 -0400,
> >>> Jerry Geis wrote:
> >>>
> >>>
> >>>> I am using the gigabyte MA78GM-US2H motherboard. it has the ALC889A audio.
> >>>>
> >>>> I am trying 1.0.19 and audio works out the analog back port but not over
> >>>> HDMI.
> >>>>
> >>>>
> >>> Never mind about "Function ID" entry. It's just a new line that was
> >>> added recently. function_id=1 means it's an audio codec.
> >>>
> >>> The way HDMI is supported are mainly either through the same audio
> >>> codec (ALC889A) or through a dedicated HDMI codec. In the former
> >>> case, you'll likely see a word "HDMI" in the digital output pin of the
> >>> codec proc file. In the latter case, you must have a different codec
> >>> chip connected to the HD-audio bus with a different codec address
> >>> number.
> >>>
> >>>
> >>> Takashi
> >>>
> >>>
> >>>
> >>>
> >>>> Codec: Realtek ALC889A
> >>>> Address: 0
> >>>> Function Id: 0x1
> >>>> <--------------------------------- this is different
> >>>> Vendor Id: 0x10ec0885
> >>>> Subsystem Id: 0x1458a002
> >>>> Revision Id: 0x100101
> >>>> No Modem Function Group found
> >>>> Default PCM:
> >>>> rates [0x560]: 44100 48000 96000 192000
> >>>> bits [0xe]: 16 20 24
> >>>> formats [0x1]: PCM
> >>>> Default Amp-In caps: N/A
> >>>> Default Amp-Out caps: N/A
> >>>> GPIO: io=2, o=0, i=0, unsolicited=1, wake=0
> >>>> IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
> >>>> IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
> >>>> Node 0x02 [Audio Output] wcaps 0x11: Stereo
> >>>> Converter: stream=0, channel=0
> >>>> PCM:
> >>>> rates [0x560]: 44100 48000 96000 192000
> >>>> bits [0xe]: 16 20 24
> >>>> formats [0x1]: PCM
> >>>> Node 0x03 [Audio Output] wcaps 0x11: Stereo
> >>>>
> >>>> I have been looking but havent found a solution yet. I tried grabbing
> >>>> the snapshot tar ball for today but I get errors on the compile.
> >>>>
> >>>> I had a similiar motherboard but it does not report Function ID: 01 : -
> >>>> HDMI audio on this board works correctly.
> >>>> Codec: Realtek ALC889A
> >>>> Address: 0
> >>>> Vendor Id: 0x10ec0885
> >>>> Subsystem Id: 0x1458a002
> >>>> Revision Id: 0x100101
> >>>> No Modem Function Group found
> >>>> Default PCM:
> >>>> rates [0x560]: 44100 48000 96000 192000
> >>>>
> >>>> Any thoughts????
> >>>>
> >>>> Jerry
> >>>> _______________________________________________
> >>>> Alsa-devel mailing list
> >>>> Alsa-devel at alsa-project.org
> >>>> http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
> >>>>
> >>>>
> >>>>
> >>>
> >>>
> >> I upload alsa-info.sh
> >>
> >> for the NOT WORKIng one
> >> http://www.alsa-project.org/db/?f=7e8bc9485e8bb98bf15dae5a0d5dc038003c3203
> >>
> >> for the working on
> >> http://www.alsa-project.org/db/?f=a18bcb6e87fe33a7365a749d0877a4546e901bf2
> >>
> >
> > How are you testing HDMI output?
> >
> >
> > Takashi
> >
> >
> I have a sharp aquos HDMI that works with the other motherboard.
>
> I am just switching between the two.
>
> I have the asound.conf set to the correct hw:X,y on both machines for HDMI.
More exactly?
Also, try like below:
% aplay -Dhdmi:1 foo.wav
Takashi
More information about the Alsa-devel
mailing list