[PATCH v4 3/5] soundwire: qcom: add static port map support

[Srinivas Kandagatla]

SoundWire device ports are statically mapped to Controller ports during
design. Add support to read these from SoundWire devices.
This controller uses static port map info to setup bandwidth
parameters for those ports.

A generic port allocation is not possible in this cases!

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla at linaro.org>
---
 drivers/soundwire/qcom.c | 20 ++++++++++++++++++--
 1 file changed, 18 insertions(+), 2 deletions(-)

diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c
index 9e70c53e2c7b..39222b04a2e0 100644
--- a/drivers/soundwire/qcom.c
+++ b/drivers/soundwire/qcom.c
@@ -460,6 +460,8 @@ static int qcom_swrm_compute_params(struct sdw_bus *bus)
 	struct sdw_slave_runtime *s_rt;
 	struct sdw_port_runtime *p_rt;
 	struct qcom_swrm_port_config *pcfg;
+	struct sdw_slave *slave;
+	unsigned int m_port;
 	int i = 0;
 
 	list_for_each_entry(m_rt, &bus->m_rt_list, bus_node) {
@@ -473,8 +475,14 @@ static int qcom_swrm_compute_params(struct sdw_bus *bus)
 		}
 
 		list_for_each_entry(s_rt, &m_rt->slave_rt_list, m_rt_node) {
+			slave = s_rt->slave;
 			list_for_each_entry(p_rt, &s_rt->port_list, port_node) {
-				pcfg = &ctrl->pconfig[i];
+				m_port = slave->m_port_map[p_rt->num];
+				/* port config starts at offset 0 so -1 from actual port number */
+				if (m_port)
+					pcfg = &ctrl->pconfig[m_port - 1];
+				else
+					pcfg = &ctrl->pconfig[i];
 				p_rt->transport_params.port_num = p_rt->num;
 				p_rt->transport_params.sample_interval =
 					pcfg->si + 1;
@@ -535,8 +543,10 @@ static int qcom_swrm_stream_alloc_ports(struct qcom_swrm_ctrl *ctrl,
 	struct sdw_master_runtime *m_rt;
 	struct sdw_slave_runtime *s_rt;
 	struct sdw_port_runtime *p_rt;
+	struct sdw_slave *slave;
 	unsigned long *port_mask;
 	int i, maxport, pn, nports = 0, ret = 0;
+	unsigned int m_port;
 
 	mutex_lock(&ctrl->port_lock);
 	list_for_each_entry(m_rt, &stream->master_list, stream_node) {
@@ -549,9 +559,15 @@ static int qcom_swrm_stream_alloc_ports(struct qcom_swrm_ctrl *ctrl,
 		}
 
 		list_for_each_entry(s_rt, &m_rt->slave_rt_list, m_rt_node) {
+			slave = s_rt->slave;
 			list_for_each_entry(p_rt, &s_rt->port_list, port_node) {
+				m_port = slave->m_port_map[p_rt->num];
 				/* Port numbers start from 1 - 14*/
-				pn = find_first_zero_bit(port_mask, maxport);
+				if (m_port)
+					pn = m_port;
+				else
+					pn = find_first_zero_bit(port_mask, maxport);
+
 				if (pn > maxport) {
 					dev_err(ctrl->dev, "All ports busy\n");
 					ret = -EBUSY;
-- 
2.21.0