[PATCH v4 2/5] soundwire: qcom: update port map allocation bit mask

Srinivas Kandagatla srinivas.kandagatla at linaro.org
Mon Mar 15 17:56:47 CET 2021


currently the internal bitmask used for allocating ports starts with offset 0.
This is bit confusing as data port numbers on Qualcomm controller are valid
from 1 to 14. So adjust this bit mask accordingly, this will also help while
adding static port map support.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla at linaro.org>
---
 drivers/soundwire/qcom.c | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)

diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c
index 6d22df01f354..9e70c53e2c7b 100644
--- a/drivers/soundwire/qcom.c
+++ b/drivers/soundwire/qcom.c
@@ -519,7 +519,7 @@ static void qcom_swrm_stream_free_ports(struct qcom_swrm_ctrl *ctrl,
 			port_mask = &ctrl->din_port_mask;
 
 		list_for_each_entry(p_rt, &m_rt->port_list, port_node)
-			clear_bit(p_rt->num - 1, port_mask);
+			clear_bit(p_rt->num, port_mask);
 	}
 
 	mutex_unlock(&ctrl->port_lock);
@@ -552,13 +552,13 @@ static int qcom_swrm_stream_alloc_ports(struct qcom_swrm_ctrl *ctrl,
 			list_for_each_entry(p_rt, &s_rt->port_list, port_node) {
 				/* Port numbers start from 1 - 14*/
 				pn = find_first_zero_bit(port_mask, maxport);
-				if (pn > (maxport - 1)) {
+				if (pn > maxport) {
 					dev_err(ctrl->dev, "All ports busy\n");
 					ret = -EBUSY;
 					goto err;
 				}
 				set_bit(pn, port_mask);
-				pconfig[nports].num = pn + 1;
+				pconfig[nports].num = pn;
 				pconfig[nports].ch_mask = p_rt->ch_mask;
 				nports++;
 			}
@@ -580,7 +580,7 @@ static int qcom_swrm_stream_alloc_ports(struct qcom_swrm_ctrl *ctrl,
 err:
 	if (ret) {
 		for (i = 0; i < nports; i++)
-			clear_bit(pconfig[i].num - 1, port_mask);
+			clear_bit(pconfig[i].num, port_mask);
 	}
 
 	mutex_unlock(&ctrl->port_lock);
@@ -754,6 +754,9 @@ static int qcom_swrm_get_port_config(struct qcom_swrm_ctrl *ctrl)
 	ctrl->num_dout_ports = val;
 
 	nports = ctrl->num_dout_ports + ctrl->num_din_ports;
+	/* Valid port numbers are from 1-14, so mask out port 0 explicitly */
+	set_bit(0, &ctrl->dout_port_mask);
+	set_bit(0, &ctrl->din_port_mask);
 
 	ret = of_property_read_u8_array(np, "qcom,ports-offset1",
 					off1, nports);
-- 
2.21.0



More information about the Alsa-devel mailing list