Convert the NAU8825 audio CODEC bindings to DT schema.
Signed-off-by: David Lin CTLIN0@nuvoton.com --- .../devicetree/bindings/sound/nau8825.txt | 111 -------- .../bindings/sound/nuvoton,nau8825.yaml | 242 ++++++++++++++++++ 2 files changed, 242 insertions(+), 111 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sound/nau8825.txt create mode 100644 Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml
diff --git a/Documentation/devicetree/bindings/sound/nau8825.txt b/Documentation/devicetree/bindings/sound/nau8825.txt deleted file mode 100644 index a9c34526f4cb..000000000000 --- a/Documentation/devicetree/bindings/sound/nau8825.txt +++ /dev/null @@ -1,111 +0,0 @@ -Nuvoton NAU8825 audio codec - -This device supports I2C only. - -Required properties: - - compatible : Must be "nuvoton,nau8825" - - - reg : the I2C address of the device. This is either 0x1a (CSB=0) or 0x1b (CSB=1). - -Optional properties: - - nuvoton,jkdet-enable: Enable jack detection via JKDET pin. - - nuvoton,jkdet-pull-enable: Enable JKDET pin pull. If set - pin pull enabled, - otherwise pin in high impedance state. - - nuvoton,jkdet-pull-up: Pull-up JKDET pin. If set then JKDET pin is pull up, otherwise pull down. - - nuvoton,jkdet-polarity: JKDET pin polarity. 0 - active high, 1 - active low. - - - nuvoton,vref-impedance: VREF Impedance selection - 0 - Open - 1 - 25 kOhm - 2 - 125 kOhm - 3 - 2.5 kOhm - - - nuvoton,micbias-voltage: Micbias voltage level. - 0 - VDDA - 1 - VDDA - 2 - VDDA * 1.1 - 3 - VDDA * 1.2 - 4 - VDDA * 1.3 - 5 - VDDA * 1.4 - 6 - VDDA * 1.53 - 7 - VDDA * 1.53 - - - nuvoton,sar-threshold-num: Number of buttons supported - - nuvoton,sar-threshold: Impedance threshold for each button. Array that contains up to 8 buttons configuration. SAR value is calculated as - SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R) - where MICBIAS is configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by 'nuvoton,sar-voltage', R - button impedance. - Refer datasheet section 10.2 for more information about threshold calculation. - - - nuvoton,sar-hysteresis: Button impedance measurement hysteresis. - - - nuvoton,sar-voltage: Reference voltage for button impedance measurement. - 0 - VDDA - 1 - VDDA - 2 - VDDA * 1.1 - 3 - VDDA * 1.2 - 4 - VDDA * 1.3 - 5 - VDDA * 1.4 - 6 - VDDA * 1.53 - 7 - VDDA * 1.53 - - - nuvoton,sar-compare-time: SAR compare time - 0 - 500 ns - 1 - 1 us - 2 - 2 us - 3 - 4 us - - - nuvoton,sar-sampling-time: SAR sampling time - 0 - 2 us - 1 - 4 us - 2 - 8 us - 3 - 16 us - - - nuvoton,short-key-debounce: Button short key press debounce time. - 0 - 30 ms - 1 - 50 ms - 2 - 100 ms - 3 - 30 ms - - - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms - - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms - - - nuvoton,crosstalk-enable: make crosstalk function enable if set. - - - nuvoton,adcout-drive-strong: make the drive strength of ADCOUT IO PIN strong if set. - Otherwise, the drive keeps normal strength. - - - nuvoton,adc-delay-ms: Delay (in ms) to make input path stable and avoid pop noise. The - default value is 125 and range between 125 to 500 ms. - - - clocks: list of phandle and clock specifier pairs according to common clock bindings for the - clocks described in clock-names - - clock-names: should include "mclk" for the MCLK master clock - -Example: - - headset: nau8825@1a { - compatible = "nuvoton,nau8825"; - reg = <0x1a>; - interrupt-parent = <&gpio>; - interrupts = <TEGRA_GPIO(E, 6) IRQ_TYPE_LEVEL_LOW>; - nuvoton,jkdet-enable; - nuvoton,jkdet-pull-enable; - nuvoton,jkdet-pull-up; - nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>; - nuvoton,vref-impedance = <2>; - nuvoton,micbias-voltage = <6>; - // Setup 4 buttons impedance according to Android specification - nuvoton,sar-threshold-num = <4>; - nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>; - nuvoton,sar-hysteresis = <1>; - nuvoton,sar-voltage = <0>; - nuvoton,sar-compare-time = <0>; - nuvoton,sar-sampling-time = <0>; - nuvoton,short-key-debounce = <2>; - nuvoton,jack-insert-debounce = <7>; - nuvoton,jack-eject-debounce = <7>; - nuvoton,crosstalk-enable; - - clock-names = "mclk"; - clocks = <&tegra_pmc TEGRA_PMC_CLK_OUT_2>; - }; diff --git a/Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml b/Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml new file mode 100644 index 000000000000..ab352422d48e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nuvoton,nau8825.yaml @@ -0,0 +1,242 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/nuvoton,nau8825.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NAU8825 audio CODEC + +maintainers: + - John Hsu KCHSU0@nuvoton.com + +allOf: + - $ref: dai-common.yaml# + +properties: + compatible: + enum: + - nuvoton,nau8825 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + description: + The CODEC's interrupt output. + + nuvoton,jkdet-enable: + description: + Enable jack detection via JKDET pin. + type: boolean + + nuvoton,jkdet-pull-enable: + description: + Enable JKDET pin pull. + If set - pin pull enabled, otherwise pin in high impedance state. + type: boolean + + nuvoton,jkdet-pull-up: + description: + Pull-up JKDET pin. + If set then JKDET pin is pull up, otherwise pull down. + type: boolean + + nuvoton,jkdet-polarity: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + JKDET pin polarity. + enum: + - 0 # active high + - 1 # active low + default: 1 + + nuvoton,vref-impedance: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + VREF Impedance selection. + enum: + - 0 # Open + - 1 # 25 kOhm + - 2 # 125 kOhm + - 3 # 2.5 kOhm + default: 2 + + nuvoton,micbias-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Micbias voltage level. + enum: + - 0 # VDDA + - 1 # VDDA + - 2 # VDDA * 1.1 + - 3 # VDDA * 1.2 + - 4 # VDDA * 1.3 + - 5 # VDDA * 1.4 + - 6 # VDDA * 1.53 + - 7 # VDDA * 1.53 + default: 6 + + nuvoton,sar-threshold-num: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Number of buttons supported. + minimum: 1 + maximum: 4 + default: 4 + + nuvoton,sar-threshold: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: + Impedance threshold for each button. Array that contains up to 8 buttons + configuration. SAR value is calculated as + SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R) where MICBIAS is + configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by + 'nuvoton,sar-voltage', R - button impedance. + Refer datasheet section 10.2 for more information about threshold + calculation. + minItems: 1 + maxItems: 4 + items: + minimum: 0 + maximum: 255 + + nuvoton,sar-hysteresis: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Button impedance measurement hysteresis. + default: 0 + + nuvoton,sar-voltage: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Reference voltage for button impedance measurement. + enum: + - 0 # VDDA + - 1 # VDDA + - 2 # VDDA * 1.1 + - 3 # VDDA * 1.2 + - 4 # VDDA * 1.3 + - 5 # VDDA * 1.4 + - 6 # VDDA * 1.53 + - 7 # VDDA * 1.53 + default: 6 + + nuvoton,sar-compare-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + SAR compare time. + enum: + - 0 # 500 ns + - 1 # 1 us + - 2 # 2 us + - 3 # 4 us + default: 1 + + nuvoton,sar-sampling-time: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + SAR sampling time. + enum: + - 0 # 2 us + - 1 # 4 us + - 2 # 8 us + - 3 # 16 us + default: 1 + + nuvoton,short-key-debounce: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Button short key press debounce time. + enum: + - 0 # 30 ms + - 1 # 50 ms + - 2 # 100 ms + - 3 # 30 ms + default: 3 + + nuvoton,jack-insert-debounce: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + number from 0 to 7 that sets debounce time to 2^(n+2) ms. + maximum: 7 + default: 7 + + nuvoton,jack-eject-debounce: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + number from 0 to 7 that sets debounce time to 2^(n+2) ms + maximum: 7 + default: 0 + + nuvoton,crosstalk-enable: + description: + make crosstalk function enable if set. + type: boolean + + nuvoton,adcout-drive-strong: + description: + make the drive strength of ADCOUT IO PIN strong if set. + Otherwise, the drive keeps normal strength. + type: boolean + + nuvoton,adc-delay-ms: + description: + Delay (in ms) to make input path stable and avoid pop noise. + The default value is 125 and range between 125 to 500 ms. + minimum: 125 + maximum: 500 + default: 125 + + clocks: + description: + list of phandle and clock specifier pairs according to common clock + bindings for the clocks described in clock-names. + maxItems: 1 + + clock-names: + description: + should include "mclk" for the MCLK master clock. + items: + - const: mclk + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + nau8825@1a { + compatible = "nuvoton,nau8825"; + reg = <0x1a>; + interrupt-parent = <&gpio>; + interrupts = <38 IRQ_TYPE_LEVEL_LOW>; + nuvoton,jkdet-enable; + nuvoton,jkdet-pull-enable; + nuvoton,jkdet-pull-up; + nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>; + nuvoton,vref-impedance = <2>; + nuvoton,micbias-voltage = <6>; + // Setup 4 buttons impedance according to Android specification + nuvoton,sar-threshold-num = <4>; + nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>; + nuvoton,sar-hysteresis = <1>; + nuvoton,sar-voltage = <0>; + nuvoton,sar-compare-time = <0>; + nuvoton,sar-sampling-time = <0>; + nuvoton,short-key-debounce = <2>; + nuvoton,jack-insert-debounce = <7>; + nuvoton,jack-eject-debounce = <7>; + nuvoton,crosstalk-enable; + + clock-names = "mclk"; + clocks = <&tegra_pmc 1>; + }; + };