[PATCH 3/3] ASoC: dt-bindings: cs42l42: Convert binding to yaml
Richard Fitzgerald
rf at opensource.cirrus.com
Thu Oct 28 16:09:02 CEST 2021
Replace the old .txt binding with a new schema binding.
At the same time, some of the descriptions are updated to make them
clearer, fix errors, or just make them fit better into the style
of schema binding.
The cirrus,hs-bias-ramp-rate property was missing from the old .txt
binding and has been added to the yaml.
Signed-off-by: Richard Fitzgerald <rf at opensource.cirrus.com>
---
.../devicetree/bindings/sound/cirrus,cs42l42.yaml | 225 +++++++++++++++++++++
.../devicetree/bindings/sound/cs42l42.txt | 115 -----------
MAINTAINERS | 1 +
3 files changed, 226 insertions(+), 115 deletions(-)
create mode 100644 Documentation/devicetree/bindings/sound/cirrus,cs42l42.yaml
delete mode 100644 Documentation/devicetree/bindings/sound/cs42l42.txt
diff --git a/Documentation/devicetree/bindings/sound/cirrus,cs42l42.yaml b/Documentation/devicetree/bindings/sound/cirrus,cs42l42.yaml
new file mode 100644
index 000000000000..31800f70e9d9
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/cirrus,cs42l42.yaml
@@ -0,0 +1,225 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/cirrus,cs42l42.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cirrus Logic CS42L42 audio CODEC
+
+maintainers:
+ - patches at opensource.cirrus.com
+
+description:
+ The CS42L42 is a low-power audio codec designed for portable applications.
+ It provides a high-dynamic range, stereo DAC for audio playback and a mono
+ high-dynamic-range ADC for audio capture. There is an integrated headset
+ detection block.
+
+properties:
+ compatible:
+ enum:
+ - cirrus,cs42l42
+
+ reg:
+ description:
+ The I2C address of the CS42L42.
+ maxItems: 1
+
+ VP-supply:
+ description:
+ VP power supply.
+
+ VCP-supply:
+ description:
+ Charge pump power supply.
+
+ VD_FILT-supply:
+ description:
+ FILT+ power supply.
+
+ VL-supply:
+ description:
+ Logic power supply.
+
+ VA-supply:
+ description:
+ Analog power supply.
+
+ reset-gpios:
+ description:
+ This pin will be asserted and then deasserted to reset the
+ CS42L42 before communication starts.
+ maxItems: 1
+
+ interrupts:
+ description:
+ Interrupt for CS42L42 IRQ line.
+ maxItems: 1
+
+ cirrus,ts-inv:
+ description: |
+ Sets the behaviour of the jack plug detect switch.
+
+ 0 - (Default) Shorted to tip when unplugged, open when plugged.
+ This is "inverted tip sense (ITS)" in the datasheet.
+
+ 1 - Open when unplugged, shorted to tip when plugged.
+ This is "normal tip sense (TS)" in the datasheet.
+
+ The CS42L42_TS_INV_* defines are available for this.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 1
+
+ cirrus,ts-dbnc-rise:
+ description: |
+ Debounce the rising edge of TIP_SENSE_PLUG. With no
+ debounce, the tip sense pin might be noisy on a plug event.
+
+ 0 - 0ms
+ 1 - 125ms
+ 2 - 250ms
+ 3 - 500ms
+ 4 - 750ms
+ 5 - 1s (Default)
+ 6 - 1.25s
+ 7 - 1.5s
+
+ The CS42L42_TS_DBNCE_* defines are available for this.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 7
+
+ cirrus,ts-dbnc-fall:
+ description: |
+ Debounce the falling edge of TIP_SENSE_UNPLUG. With no
+ debounce, the tip sense pin might be noisy on an unplug event.
+
+ 0 - 0ms
+ 1 - 125ms
+ 2 - 250ms
+ 3 - 500ms
+ 4 - 750ms
+ 5 - 1s (Default)
+ 6 - 1.25s
+ 7 - 1.5s
+
+ The CS42L42_TS_DBNCE_* defines are available for this.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 7
+
+ cirrus,btn-det-init-dbnce:
+ description: |
+ This sets how long to wait after enabling button detection
+ interrupts before servicing button interrupts, to allow the
+ HS bias time to settle. Value is in milliseconds.
+ There may be erroneous button interrupts if this debounce time
+ is too short.
+
+ 0ms - 200ms,
+ Default = 100ms
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 200
+
+ cirrus,btn-det-event-dbnce:
+ description: |
+ This sets how long to wait after receiving a button press
+ interrupt before processing it. Allows time for the button
+ press to make a clean connection with the bias resistors.
+ Value is in milliseconds.
+
+ 0ms - 20ms,
+ Default = 10ms
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 20
+
+ cirrus,bias-lvls:
+ description: |
+ For a level-detect headset button scheme, each button will bias
+ the mic pin to a certain voltage. To determine which button was
+ pressed, the voltage is compared to sequential, decreasing
+ voltages, until the compared voltage < bias voltage.
+ For different hardware setups, a designer might want to tweak this.
+ This is an array of descending values for the comparator voltage,
+ given as percent of the HSBIAS voltage.
+
+ Array of 4 values, each 0-63
+ < x1 x2 x3 x4 >
+ Default = < 15 8 4 1 >
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 4
+ maxItems: 4
+ items:
+ minimum: 0
+ maximum: 63
+
+ cirrus,hs-bias-ramp-rate:
+ description: |
+ If present this sets the rate that the HS bias should rise and fall.
+ The actual rise and fall times depend on external hardware (the
+ datasheet gives several rise and fall time examples).
+
+ 0 - Fast rise time; slow, load-dependent fall time
+ 1 - Fast
+ 2 - Slow (default)
+ 3 - Slowest
+
+ The CS42L42_HSBIAS_RAMP_* defines are available for this.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 3
+
+ cirrus,hs-bias-sense-disable:
+ description: |
+ If present the HSBIAS sense is disabled. Configures HSBIAS output
+ current sense through the external 2.21-k resistor. HSBIAS_SENSE
+ is a hardware feature to reduce the potential pop noise when the
+ headset plug is removed slowly. But on some platforms ESD voltage
+ will affect it causing plug detection to fail, especially with CTIA
+ headset type. For different hardware setups, a designer might want
+ to tweak default behavior.
+ type: boolean
+
+required:
+ - compatible
+ - reg
+ - VP-supply
+ - VCP-supply
+ - VD_FILT-supply
+ - VL-supply
+ - VA-supply
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/sound/cs42l42.h>
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cs42l42: cs42l42 at 48 {
+ compatible = "cirrus,cs42l42";
+ reg = <0x48>;
+ VA-supply = <&dummy_vreg>;
+ VP-supply = <&dummy_vreg>;
+ VCP-supply = <&dummy_vreg>;
+ VD_FILT-supply = <&dummy_vreg>;
+ VL-supply = <&dummy_vreg>;
+
+ reset-gpios = <&axi_gpio_0 1 0>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <55 8>;
+
+ cirrus,ts-inv = <CS42L42_TS_INV_DIS>;
+ cirrus,ts-dbnc-rise = <CS42L42_TS_DBNCE_1000>;
+ cirrus,ts-dbnc-fall = <CS42L42_TS_DBNCE_0>;
+ cirrus,btn-det-init-dbnce = <100>;
+ cirrus,btn-det-event-dbnce = <10>;
+ cirrus,bias-lvls = <0x0F 0x08 0x04 0x01>;
+ cirrus,hs-bias-ramp-rate = <CS42L42_HSBIAS_RAMP_SLOW>;
+ };
+ };
diff --git a/Documentation/devicetree/bindings/sound/cs42l42.txt b/Documentation/devicetree/bindings/sound/cs42l42.txt
deleted file mode 100644
index 3b7705623980..000000000000
--- a/Documentation/devicetree/bindings/sound/cs42l42.txt
+++ /dev/null
@@ -1,115 +0,0 @@
-CS42L42 audio CODEC
-
-Required properties:
-
- - compatible : "cirrus,cs42l42"
-
- - reg : the I2C address of the device for I2C.
-
- - VP-supply, VCP-supply, VD_FILT-supply, VL-supply, VA-supply :
- power supplies for the device, as covered in
- Documentation/devicetree/bindings/regulator/regulator.txt.
-
-Optional properties:
-
- - reset-gpios : a GPIO spec for the reset pin. If specified, it will be
- deasserted before communication to the codec starts.
-
- - interrupts : IRQ line info CS42L42.
- (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
- for further information relating to interrupt properties)
-
- - cirrus,ts-inv : Boolean property. Sets the behaviour of the jack plug
- detect switch.
-
- 0 = (Default) Shorted to tip when unplugged, open when plugged.
- This is "inverted tip sense (ITS)" in the datasheet.
-
- 1 = Open when unplugged, shorted to tip when plugged.
- This is "normal tip sense (TS)" in the datasheet.
-
- - cirrus,ts-dbnc-rise : Debounce the rising edge of TIP_SENSE_PLUG. With no
- debounce, the tip sense pin might be noisy on a plug event.
-
- 0 - 0ms,
- 1 - 125ms,
- 2 - 250ms,
- 3 - 500ms,
- 4 - 750ms,
- 5 - (Default) 1s,
- 6 - 1.25s,
- 7 - 1.5s,
-
- - cirrus,ts-dbnc-fall : Debounce the falling edge of TIP_SENSE_UNPLUG.
- With no debounce, the tip sense pin might be noisy on an unplug event.
-
- 0 - 0ms,
- 1 - 125ms,
- 2 - 250ms,
- 3 - 500ms,
- 4 - 750ms,
- 5 - (Default) 1s,
- 6 - 1.25s,
- 7 - 1.5s,
-
- - cirrus,btn-det-init-dbnce : This sets how long the driver sleeps after
- enabling button detection interrupts. After auto-detection and before
- servicing button interrupts, the HS bias needs time to settle. If you
- don't wait, there is possibility for erroneous button interrupt.
-
- 0ms - 200ms,
- Default = 100ms
-
- - cirrus,btn-det-event-dbnce : This sets how long the driver delays after
- receiving a button press interrupt. With level detect interrupts, you want
- to wait a small amount of time to make sure the button press is making a
- clean connection with the bias resistors.
-
- 0ms - 20ms,
- Default = 10ms
-
- - cirrus,bias-lvls : For a level-detect headset button scheme, each button
- will bias the mic pin to a certain voltage. To determine which button was
- pressed, the driver will compare this biased voltage to sequential,
- decreasing voltages and will stop when a comparator is tripped,
- indicating a comparator voltage < bias voltage. This value represents a
- percentage of the internally generated HS bias voltage. For different
- hardware setups, a designer might want to tweak this. This is an array of
- descending values for the comparator voltage.
-
- Array of 4 values
- Each 0-63
- < x1 x2 x3 x4 >
- Default = < 15 8 4 1>
-
- - cirrus,hs-bias-sense-disable: This is boolean property. If present the
- HSBIAS sense is disabled. Configures HSBIAS output current sense through
- the external 2.21-k resistor. HSBIAS_SENSE is hardware feature to reduce
- the potential pop noise during the headset plug out slowly. But on some
- platforms ESD voltage will affect it causing test to fail, especially
- with CTIA headset type. For different hardware setups, a designer might
- want to tweak default behavior.
-
-Example:
-
-cs42l42: cs42l42 at 48 {
- compatible = "cirrus,cs42l42";
- reg = <0x48>;
- VA-supply = <&dummy_vreg>;
- VP-supply = <&dummy_vreg>;
- VCP-supply = <&dummy_vreg>;
- VD_FILT-supply = <&dummy_vreg>;
- VL-supply = <&dummy_vreg>;
-
- reset-gpios = <&axi_gpio_0 1 0>;
- interrupt-parent = <&gpio0>;
- interrupts = <55 8>
-
- cirrus,ts-inv = <0x00>;
- cirrus,ts-dbnc-rise = <0x05>;
- cirrus,ts-dbnc-fall = <0x00>;
- cirrus,btn-det-init-dbnce = <100>;
- cirrus,btn-det-event-dbnce = <10>;
- cirrus,bias-lvls = <0x0F 0x08 0x04 0x01>;
- cirrus,hs-bias-ramp-rate = <0x02>;
-};
diff --git a/MAINTAINERS b/MAINTAINERS
index 6fc811cd86e9..38555c7f0ce4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4449,6 +4449,7 @@ M: David Rhodes <david.rhodes at cirrus.com>
L: alsa-devel at alsa-project.org (moderated for non-subscribers)
L: patches at opensource.cirrus.com
S: Maintained
+F: Documentation/devicetree/bindings/sound/cirrus,cs*
F: sound/soc/codecs/cs*
CIRRUS LOGIC DSP FIRMWARE DRIVER
--
2.11.0
More information about the Alsa-devel
mailing list