[PATCH v2 1/5] soundwire: qcom: add support to missing transport params
Pierre-Louis Bossart
pierre-louis.bossart at linux.intel.com
Fri Feb 26 17:45:30 CET 2021
On 2/26/21 9:58 AM, Srinivas Kandagatla wrote:
> Some of the transport parameters derived from device tree
> are not fully parsed by the driver.
>
> This patch adds support to parse those missing parameters.
>
> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla at linaro.org>
> ---
> drivers/soundwire/qcom.c | 99 ++++++++++++++++++++++++++++++++++++++--
> 1 file changed, 95 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c
> index 6d22df01f354..fee7465c72c2 100644
> --- a/drivers/soundwire/qcom.c
> +++ b/drivers/soundwire/qcom.c
> @@ -54,7 +54,13 @@
> #define SWRM_MCP_SLV_STATUS 0x1090
> #define SWRM_MCP_SLV_STATUS_MASK GENMASK(1, 0)
> #define SWRM_DP_PORT_CTRL_BANK(n, m) (0x1124 + 0x100 * (n - 1) + 0x40 * m)
> +#define SWRM_DP_PORT_CTRL_2_BANK(n, m) (0x1128 + 0x100 * (n - 1) + 0x40 * m)
> +#define SWRM_DP_BLOCK_CTRL_1(n) (0x112C + 0x100 * (n - 1))
> +#define SWRM_DP_BLOCK_CTRL2_BANK(n, m) (0x1130 + 0x100 * (n - 1) + 0x40 * m)
> +#define SWRM_DP_PORT_HCTRL_BANK(n, m) (0x1134 + 0x100 * (n - 1) + 0x40 * m)
> #define SWRM_DP_BLOCK_CTRL3_BANK(n, m) (0x1138 + 0x100 * (n - 1) + 0x40 * m)
> +#define SWRM_DIN_DPn_PCM_PORT_CTRL(n) (0x1054 + 0x100 * (n - 1))
> +
> #define SWRM_DP_PORT_CTRL_EN_CHAN_SHFT 0x18
> #define SWRM_DP_PORT_CTRL_OFFSET2_SHFT 0x10
> #define SWRM_DP_PORT_CTRL_OFFSET1_SHFT 0x08
> @@ -73,12 +79,20 @@
> #define QCOM_SDW_MAX_PORTS 14
> #define DEFAULT_CLK_FREQ 9600000
> #define SWRM_MAX_DAIS 0xF
> +#define SWR_INVALID_PARAM 0xFF
> +#define SWR_HSTOP_MAX_VAL 0xF
> +#define SWR_HSTART_MIN_VAL 0x0
>
> struct qcom_swrm_port_config {
> u8 si;
> u8 off1;
> u8 off2;
> u8 bp_mode;
> + u8 hstart;
> + u8 hstop;
> + u8 word_length;
> + u8 blk_group_count;
> + u8 lane_control;
> };
>
> struct qcom_swrm_ctrl {
> @@ -396,7 +410,13 @@ static int qcom_swrm_port_params(struct sdw_bus *bus,
> struct sdw_port_params *p_params,
> unsigned int bank)
> {
> - /* TBD */
> + struct qcom_swrm_ctrl *ctrl = to_qcom_sdw(bus);
> +
> + if (p_params->bps != SWR_INVALID_PARAM)
this is odd. sdw_port_params is a structure in
include/linux/soundwire/sdw.h, but here you are comparing the value with
a private qualcomm-defined value.
The Word length of the port is limited by the standard (64), so your
choice of 0xFF for SWR_INVALID_PARAM is legit, but it should be a
'public' define.
> + return ctrl->reg_write(ctrl,
> + SWRM_DP_BLOCK_CTRL_1(p_params->num),
> + p_params->bps - 1);
> +
> return 0;
> }
>
> @@ -415,10 +435,32 @@ static int qcom_swrm_transport_params(struct sdw_bus *bus,
>
> ret = ctrl->reg_write(ctrl, reg, value);
>
> - if (!ret && params->blk_pkg_mode) {
> - reg = SWRM_DP_BLOCK_CTRL3_BANK(params->port_num, bank);
> + if (params->lane_ctrl != SWR_INVALID_PARAM) {
> + reg = SWRM_DP_PORT_CTRL_2_BANK(params->port_num, bank);
> + value = params->lane_ctrl;
> + ret = ctrl->reg_write(ctrl, reg, value);
> + }
>
> - ret = ctrl->reg_write(ctrl, reg, 1);
> + if (params->blk_grp_ctrl != SWR_INVALID_PARAM) {
> + reg = SWRM_DP_BLOCK_CTRL2_BANK(params->port_num, bank);
> + value = params->blk_grp_ctrl;
> + ret = ctrl->reg_write(ctrl, reg, value);
> + }
> +
> + if (params->hstart != SWR_INVALID_PARAM
> + && params->hstop != SWR_INVALID_PARAM) {
> + reg = SWRM_DP_PORT_HCTRL_BANK(params->port_num, bank);
> + value = (params->hstop << 4) | params->hstart;
> + ret = ctrl->reg_write(ctrl, reg, value);
> + } else {
> + reg = SWRM_DP_PORT_HCTRL_BANK(params->port_num, bank);
> + value = (SWR_HSTOP_MAX_VAL << 4) | SWR_HSTART_MIN_VAL;
> + ret = ctrl->reg_write(ctrl, reg, value);
> + }
> +
> + if (params->blk_pkg_mode != SWR_INVALID_PARAM) {
> + reg = SWRM_DP_BLOCK_CTRL3_BANK(params->port_num, bank);
> + ret = ctrl->reg_write(ctrl, reg, params->blk_pkg_mode);
> }
same comments here, you should define a public define for all those
parameters.
> return ret;
> @@ -470,6 +512,17 @@ static int qcom_swrm_compute_params(struct sdw_bus *bus)
> p_rt->transport_params.offset1 = pcfg->off1;
> p_rt->transport_params.offset2 = pcfg->off2;
> p_rt->transport_params.blk_pkg_mode = pcfg->bp_mode;
> + p_rt->transport_params.blk_grp_ctrl = pcfg->blk_group_count;
> + p_rt->transport_params.hstart = pcfg->hstart;
> + p_rt->transport_params.hstop = pcfg->hstop;
> + p_rt->transport_params.lane_ctrl = pcfg->lane_control;
> + if (pcfg->word_length != SWR_INVALID_PARAM) {
> + sdw_fill_port_params(&p_rt->port_params,
> + p_rt->num, pcfg->word_length + 1,
> + SDW_PORT_FLOW_MODE_ISOCH,
> + SDW_PORT_DATA_MODE_NORMAL);
> + }
> +
> }
>
> list_for_each_entry(s_rt, &m_rt->slave_rt_list, m_rt_node) {
> @@ -481,6 +534,18 @@ static int qcom_swrm_compute_params(struct sdw_bus *bus)
> p_rt->transport_params.offset1 = pcfg->off1;
> p_rt->transport_params.offset2 = pcfg->off2;
> p_rt->transport_params.blk_pkg_mode = pcfg->bp_mode;
> + p_rt->transport_params.blk_grp_ctrl = pcfg->blk_group_count;
> +
> + p_rt->transport_params.hstart = pcfg->hstart;
> + p_rt->transport_params.hstop = pcfg->hstop;
> + p_rt->transport_params.lane_ctrl = pcfg->lane_control;
> + if (pcfg->word_length != SWR_INVALID_PARAM) {
> + sdw_fill_port_params(&p_rt->port_params,
> + p_rt->num,
> + pcfg->word_length + 1,
> + SDW_PORT_FLOW_MODE_ISOCH,
> + SDW_PORT_DATA_MODE_NORMAL);
> + }
> i++;
> }
> }
> @@ -728,6 +793,11 @@ static int qcom_swrm_get_port_config(struct qcom_swrm_ctrl *ctrl)
> u8 off2[QCOM_SDW_MAX_PORTS];
> u8 si[QCOM_SDW_MAX_PORTS];
> u8 bp_mode[QCOM_SDW_MAX_PORTS] = { 0, };
> + u8 hstart[QCOM_SDW_MAX_PORTS];
> + u8 hstop[QCOM_SDW_MAX_PORTS];
> + u8 word_length[QCOM_SDW_MAX_PORTS];
> + u8 blk_group_count[QCOM_SDW_MAX_PORTS];
> + u8 lane_control[QCOM_SDW_MAX_PORTS];
> int i, ret, nports, val;
>
> ctrl->reg_read(ctrl, SWRM_COMP_PARAMS, &val);
> @@ -772,11 +842,32 @@ static int qcom_swrm_get_port_config(struct qcom_swrm_ctrl *ctrl)
>
> ret = of_property_read_u8_array(np, "qcom,ports-block-pack-mode",
> bp_mode, nports);
> +
> + memset(hstart, SWR_INVALID_PARAM, QCOM_SDW_MAX_PORTS);
> + of_property_read_u8_array(np, "qcom,ports-hstart", hstart, nports);
> +
> + memset(hstop, SWR_INVALID_PARAM, QCOM_SDW_MAX_PORTS);
> + of_property_read_u8_array(np, "qcom,ports-hstop", hstop, nports);
> +
> + memset(word_length, SWR_INVALID_PARAM, QCOM_SDW_MAX_PORTS);
> + of_property_read_u8_array(np, "qcom,ports-word-length", word_length, nports);
> +
> + memset(blk_group_count, SWR_INVALID_PARAM, QCOM_SDW_MAX_PORTS);
> + of_property_read_u8_array(np, "qcom,ports-block-group-count", blk_group_count, nports);
> +
> + memset(lane_control, SWR_INVALID_PARAM, QCOM_SDW_MAX_PORTS);
> + of_property_read_u8_array(np, "qcom,ports-lane-control", lane_control, nports);
> +
> for (i = 0; i < nports; i++) {
> ctrl->pconfig[i].si = si[i];
> ctrl->pconfig[i].off1 = off1[i];
> ctrl->pconfig[i].off2 = off2[i];
> ctrl->pconfig[i].bp_mode = bp_mode[i];
> + ctrl->pconfig[i].hstart = hstart[i];
> + ctrl->pconfig[i].hstop = hstop[i];
> + ctrl->pconfig[i].word_length = word_length[i];
> + ctrl->pconfig[i].blk_group_count = blk_group_count[i];
> + ctrl->pconfig[i].lane_control = lane_control[i];
> }
I don't get why you test the values parsed from DT before writing the
registers. Why do test them here? if some values are incorrect it's much
better to provide an error log instead of writing a partially valid
setup to hardware, no?
>
> return 0;
>
More information about the Alsa-devel
mailing list