[PATCH 5/5] ASoC: qcom: apq8016_sbc: Allow routing audio through QDSP6
Srinivas Kandagatla
srinivas.kandagatla at linaro.org
Fri Dec 3 11:35:08 CET 2021
Thanks Stephan for doing this,
I have tested DB410c this use case in the past using similar patch [1].
Over all it looks good, except one comment.
On 02/12/2021 14:55, Stephan Gerhold wrote:
> The apq8016-sbc-sndcard is designed to be used with the LPASS drivers
> (bypassing the combined audio/modem DSP in MSM8916/APQ8016).
> Make it possible to use QDSP6 audio instead for the msm8916-qdsp6-sndcard.
>
> This only requires adding some additional hooks that set up the DPCM
> backends correctly. Similar code is already used in drivers for newer
> SoCs such as apq8096.c, sdm845.c and sm8250.c.
>
> A slightly different initialization sequence is used for the apq8016-sbc
> and msm8916-qdsp6 sound card by defining the apq8016_sbc_add_ops()
> function as device match data.
Other alternative is to reuse card->name populated from "qcom,model"
property to differentiate between both of these.
This should also help in differentiating UCM configs.
>
> Cc: Srinivas Kandagatla <srinivas.kandagatla at linaro.org>
> Signed-off-by: Stephan Gerhold <stephan at gerhold.net>
Few minor nits, other than that it LGTM,
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla at linaro.org>
> ---
> sound/soc/qcom/apq8016_sbc.c | 134 +++++++++++++++++++++++++++++++++--
> 1 file changed, 129 insertions(+), 5 deletions(-)
>
> diff --git a/sound/soc/qcom/apq8016_sbc.c b/sound/soc/qcom/apq8016_sbc.c
> index ba2a98268ee4..f9d69375320e 100644
> --- a/sound/soc/qcom/apq8016_sbc.c
> +++ b/sound/soc/qcom/apq8016_sbc.c
> @@ -17,6 +17,9 @@
> #include <uapi/linux/input-event-codes.h>
> #include <dt-bindings/sound/apq8016-lpass.h>
> #include "common.h"
> +#include "qdsp6/q6afe.h"
> +
> +#define MI2S_COUNT (MI2S_QUATERNARY + 1)
>
> struct apq8016_sbc_data {
> struct snd_soc_card card;
> @@ -24,6 +27,7 @@ struct apq8016_sbc_data {
> void __iomem *spkr_iomux;
> struct snd_soc_jack jack;
> bool jack_setup;
> + int mi2s_clk_count[MI2S_COUNT];
> };
>
> #define MIC_CTRL_TER_WS_SLAVE_SEL BIT(21)
> @@ -38,10 +42,10 @@ struct apq8016_sbc_data {
> #define SPKR_CTL_TLMM_WS_EN_SEL_MASK GENMASK(19, 18)
> #define SPKR_CTL_TLMM_WS_EN_SEL_SEC BIT(18)
> #define DEFAULT_MCLK_RATE 9600000
> +#define MI2S_BCLK_RATE 1536000
>
> -static int apq8016_sbc_dai_init(struct snd_soc_pcm_runtime *rtd)
> +static int apq8016_dai_init(struct snd_soc_pcm_runtime *rtd, int mi2s)
> {
> - struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0);
> struct snd_soc_dai *codec_dai;
> struct snd_soc_component *component;
> struct snd_soc_card *card = rtd->card;
> @@ -49,7 +53,7 @@ static int apq8016_sbc_dai_init(struct snd_soc_pcm_runtime *rtd)
> int i, rval;
> u32 value;
>
> - switch (cpu_dai->id) {
> + switch (mi2s) {
> case MI2S_PRIMARY:
> writel(readl(pdata->spkr_iomux) | SPKR_CTL_PRI_WS_SLAVE_SEL_11,
> pdata->spkr_iomux);
> @@ -128,6 +132,13 @@ static int apq8016_sbc_dai_init(struct snd_soc_pcm_runtime *rtd)
> return 0;
> }
>
> +static int apq8016_sbc_dai_init(struct snd_soc_pcm_runtime *rtd)
> +{
> + struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0);
> +
> + return apq8016_dai_init(rtd, cpu_dai->id);
> +}
> +
> static void apq8016_sbc_add_ops(struct snd_soc_card *card)
> {
> struct snd_soc_dai_link *link;
> @@ -137,6 +148,113 @@ static void apq8016_sbc_add_ops(struct snd_soc_card *card)
> link->init = apq8016_sbc_dai_init;
> }
>
> +static int qdsp6_dai_get_lpass_id(struct snd_soc_dai *cpu_dai)
> +{
> + switch (cpu_dai->id) {
> + case PRIMARY_MI2S_RX:
> + case PRIMARY_MI2S_TX:
> + return MI2S_PRIMARY;
> + case SECONDARY_MI2S_RX:
> + case SECONDARY_MI2S_TX:
> + return MI2S_SECONDARY;
> + case TERTIARY_MI2S_RX:
> + case TERTIARY_MI2S_TX:
> + return MI2S_TERTIARY;
> + case QUATERNARY_MI2S_RX:
> + case QUATERNARY_MI2S_TX:
> + return MI2S_QUATERNARY;
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static int msm8916_qdsp6_dai_init(struct snd_soc_pcm_runtime *rtd)
> +{
> + struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0);
> +
> + snd_soc_dai_set_fmt(cpu_dai, SND_SOC_DAIFMT_CBS_CFS);
> + return apq8016_dai_init(rtd, qdsp6_dai_get_lpass_id(cpu_dai));
> +}
> +
> +static int msm8916_qdsp6_startup(struct snd_pcm_substream *substream)
> +{
> + struct snd_soc_pcm_runtime *rtd = substream->private_data;
> + struct snd_soc_card *card = rtd->card;
> + struct apq8016_sbc_data *data = snd_soc_card_get_drvdata(card);
> + struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0);
> + int mi2s, ret;
> +
> + mi2s = qdsp6_dai_get_lpass_id(cpu_dai);
> + if (mi2s < 0)
> + return mi2s;
> +
> + if (++data->mi2s_clk_count[mi2s] > 1)
> + return 0;
> +
Am assuming that as you are not setting any DIGITAL CDC clock here you
might be using an external codec.
> + ret = snd_soc_dai_set_sysclk(cpu_dai, LPAIF_BIT_CLK, MI2S_BCLK_RATE, 0);
> + if (ret)
> + dev_err(card->dev, "Failed to enable LPAIF bit clk: %d\n", ret);
> + return ret;
> +}
> +
> +static void msm8916_qdsp6_shutdown(struct snd_pcm_substream *substream)
> +{
> + struct snd_soc_pcm_runtime *rtd = substream->private_data;
> + struct snd_soc_card *card = rtd->card;
> + struct apq8016_sbc_data *data = snd_soc_card_get_drvdata(card);
> + struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0);
> + int mi2s, ret;
> +
> + mi2s = qdsp6_dai_get_lpass_id(cpu_dai);
> + if (mi2s < 0)
> + return;
> +
> + if (--data->mi2s_clk_count[mi2s] > 0)
> + return;
> +
> + ret = snd_soc_dai_set_sysclk(cpu_dai, LPAIF_BIT_CLK, 0, 0);
> + if (ret)
> + dev_err(card->dev, "Failed to disable LPAIF bit clk: %d\n", ret);
> +}
> +
> +static const struct snd_soc_ops msm8916_qdsp6_be_ops = {
> + .startup = msm8916_qdsp6_startup,
> + .shutdown = msm8916_qdsp6_shutdown,
> +};
> +
> +static int msm8916_qdsp6_be_hw_params_fixup(struct snd_soc_pcm_runtime *rtd,
> + struct snd_pcm_hw_params *params)
> +{
> + struct snd_interval *rate = hw_param_interval(params,
> + SNDRV_PCM_HW_PARAM_RATE);
> + struct snd_interval *channels = hw_param_interval(params,
> + SNDRV_PCM_HW_PARAM_CHANNELS);
> + struct snd_mask *fmt = hw_param_mask(params, SNDRV_PCM_HW_PARAM_FORMAT);
> +
> + rate->min = rate->max = 48000;
> + channels->min = channels->max = 2;
> + snd_mask_set_format(fmt, SNDRV_PCM_FORMAT_S16_LE);
> +
> + return 0;
> +}
> +
> +static void msm8916_qdsp6_add_ops(struct snd_soc_card *card)
> +{
> + struct snd_soc_dai_link *link;
> + int i;
> +
> + /* Make it obvious to userspace that QDSP6 is used */
> + card->components = "qdsp6";
> +
> + for_each_card_prelinks(card, i, link) {
> + if (link->no_pcm) {
> + link->init = msm8916_qdsp6_dai_init;
> + link->ops = &msm8916_qdsp6_be_ops;
> + link->be_hw_params_fixup = msm8916_qdsp6_be_hw_params_fixup;
> + }
> + }
> +}
> +
> static const struct snd_soc_dapm_widget apq8016_sbc_dapm_widgets[] = {
>
> SND_SOC_DAPM_MIC("Handset Mic", NULL),
> @@ -148,11 +266,16 @@ static const struct snd_soc_dapm_widget apq8016_sbc_dapm_widgets[] = {
>
> static int apq8016_sbc_platform_probe(struct platform_device *pdev)
> {
> + void (*add_ops)(struct snd_soc_card *card);
> struct device *dev = &pdev->dev;
> struct snd_soc_card *card;
> struct apq8016_sbc_data *data;
> int ret;
>
> + add_ops = device_get_match_data(&pdev->dev);
> + if (!add_ops)
> + return -EINVAL;
We will never hit the error case here because without a match we can not
even enter the probe function.
--srini
> +
> data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
> if (!data)
> return -ENOMEM;
> @@ -177,12 +300,13 @@ static int apq8016_sbc_platform_probe(struct platform_device *pdev)
>
> snd_soc_card_set_drvdata(card, data);
>
> - apq8016_sbc_add_ops(card);
> + add_ops(card);
> return devm_snd_soc_register_card(&pdev->dev, card);
> }
>
> static const struct of_device_id apq8016_sbc_device_id[] __maybe_unused = {
> - { .compatible = "qcom,apq8016-sbc-sndcard" },
> + { .compatible = "qcom,apq8016-sbc-sndcard", .data = apq8016_sbc_add_ops },
> + { .compatible = "qcom,msm8916-qdsp6-sndcard", .data = msm8916_qdsp6_add_ops },
> {},
> };
> MODULE_DEVICE_TABLE(of, apq8016_sbc_device_id);
>
[1]:
https://git.linaro.org/people/srinivas.kandagatla/linux.git/commit/?h=q6dsp-db410c-v5.11-rc6&id=9d62822a5f66cd06a5e6b31f6b841a25c143926c
More information about the Alsa-devel
mailing list