[PATCH v2 2/4] dt-bindings: sound: add rockchip i2s-tdm binding

[Rob Herring]

On Fri, Aug 20, 2021 at 08:27:29PM +0200, Nicolas Frattaroli wrote:
> This adds the YAML bindings for the Rockchip I2S/TDM audio driver.
> 
> Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas at gmail.com>
> ---
>  .../bindings/sound/rockchip,i2s-tdm.yaml      | 193 ++++++++++++++++++
>  1 file changed, 193 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/sound/rockchip,i2s-tdm.yaml
> 
> diff --git a/Documentation/devicetree/bindings/sound/rockchip,i2s-tdm.yaml b/Documentation/devicetree/bindings/sound/rockchip,i2s-tdm.yaml
> new file mode 100644
> index 000000000000..1e8c1500ba40
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/sound/rockchip,i2s-tdm.yaml
> @@ -0,0 +1,193 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/sound/rockchip,i2s-tdm.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Rockchip I2S/TDM Controller
> +
> +description:
> +  The Rockchip I2S/TDM Controller is a Time Division Multiplexed
> +  audio interface found in various Rockchip SoCs, allowing up
> +  to 8 channels of audio over a serial interface.
> +
> +maintainers:
> +  - Nicolas Frattaroli <frattaroli.nicolas at gmail.com>
> +
> +properties:
> +  compatible:
> +    enum:
> +      - rockchip,px30-i2s-tdm
> +      - rockchip,rk1808-i2s-tdm
> +      - rockchip,rk3308-i2s-tdm
> +      - rockchip,rk3568-i2s-tdm
> +      - rockchip,rv1126-i2s-tdm
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  dmas:
> +    minItems: 1
> +    maxItems: 2
> +
> +  dma-names:
> +    minItems: 1
> +    items:
> +      - const: rx
> +      - const: tx
> +
> +  clocks:
> +    items:
> +      - description: clock for TX
> +      - description: clock for RX
> +      - description: AHB clock driving the interface
> +
> +  clock-names:
> +    items:
> +      - const: mclk_tx
> +      - const: mclk_rx
> +      - const: hclk
> +
> +  rockchip,frame-width:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    default: 64
> +    minimum: 32
> +    maximum: 512
> +    description:
> +      Width of a frame, usually slot width multiplied by number of slots.
> +      Must be even.
> +
> +  resets:
> +    items:
> +      - description: reset for TX
> +      - description: reset for RX
> +
> +  reset-names:
> +    items:
> +      - const: tx-m
> +      - const: rx-m
> +
> +  rockchip,cru:
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +    description:
> +      The phandle of the cru.
> +      Required if both playback and capture are used, i.e. if rockchip,clk-trcm
> +      is 0.

Another case of the nonexistent rockchip,clk-trcm.


> +
> +  rockchip,grf:
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +    description:
> +      The phandle of the syscon node for the GRF register.
> +
> +  rockchip,mclk-calibrate:
> +    description:
> +      Enable mclk source calibration.
> +    type: boolean
> +
> +  rockchip,trcm-sync-tx-only:
> +    type: boolean
> +    description: Use TX BCLK/LRCK for both TX and RX.
> +
> +  rockchip,trcm-sync-rx-only:
> +    type: boolean
> +    description: Use RX BCLK/LRCK for both TX and RX.
> +
> +  "#sound-dai-cells":
> +    const: 0
> +
> +  rockchip,i2s-rx-route:
> +    $ref: /schemas/types.yaml#/definitions/uint32-array
> +    description:
> +      Defines the mapping of I2S RX sdis to I2S data bus lines.
> +      By default, they are mapped one-to-one.
> +    items:
> +      - description: which sdi to connect to data line 0
> +      - description: which sdi to connect to data line 1
> +      - description: which sdi to connect to data line 2
> +      - description: which sdi to connect to data line 3
> +
> +  rockchip,i2s-tx-route:
> +    $ref: /schemas/types.yaml#/definitions/uint32-array
> +    description:
> +      Defines the mapping of I2S TX sdos to I2S data bus lines.
> +      By default, they are mapped one-to-one.
> +    items:
> +      - description: which sdo to connect to data line 0
> +      - description: which sdo to connect to data line 1
> +      - description: which sdo to connect to data line 2
> +      - description: which sdo to connect to data line 3
> +
> +  rockchip,tdm-fsync-half-frame:
> +    description: Whether to use half frame fsync.
> +    type: boolean
> +
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - dmas
> +  - dma-names
> +  - clocks
> +  - clock-names
> +  - resets
> +  - reset-names
> +  - rockchip,grf
> +  - "#sound-dai-cells"
> +
> +allOf:
> +  - if:
> +      properties:
> +        rockchip,trcm-sync-tx-only: false
> +        rockchip,trcm-sync-rx-only: false
> +    then:
> +      required:
> +        - rockchip,cru
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/rk3568-cru.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    #include <dt-bindings/pinctrl/rockchip.h>
> +
> +    foo {
> +        #address-cells = <2>;
> +        #size-cells = <2>;
> +        i2s at fe410000 {
> +            compatible = "rockchip,rk3568-i2s-tdm";
> +            reg = <0x0 0xfe410000 0x0 0x1000>;
> +            interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
> +            clocks = <&cru MCLK_I2S1_8CH_TX>, <&cru MCLK_I2S1_8CH_RX>,
> +                     <&cru HCLK_I2S1_8CH>;
> +            clock-names = "mclk_tx", "mclk_rx", "hclk";
> +            dmas = <&dmac1 3>, <&dmac1 2>;
> +            dma-names = "rx", "tx";
> +            resets = <&cru SRST_M_I2S1_8CH_TX>, <&cru SRST_M_I2S1_8CH_RX>;
> +            reset-names = "tx-m", "rx-m";
> +            rockchip,trcm-sync-tx-only;
> +            rockchip,cru = <&cru>;
> +            rockchip,grf = <&grf>;
> +            #sound-dai-cells = <0>;
> +            pinctrl-names = "default";
> +            pinctrl-0 =
> +                <&i2s1m0_sclktx
> +                &i2s1m0_sclkrx
> +                &i2s1m0_lrcktx
> +                &i2s1m0_lrckrx
> +                &i2s1m0_sdi0
> +                &i2s1m0_sdi1
> +                &i2s1m0_sdi2
> +                &i2s1m0_sdi3
> +                &i2s1m0_sdo0
> +                &i2s1m0_sdo1
> +                &i2s1m0_sdo2
> +                &i2s1m0_sdo3>;
> +            status = "okay";

Sorry if I wasn't clear, but you don't need status at all in examples as 
okay is the default.

Rob