[PATCH v2 3/3] soundwire: qcom: get max rows and cols info from compatible

[Srinivas Kandagatla]

On 16/09/2020 13:49, Vinod Koul wrote:
> On 16-09-20, 10:21, Srinivas Kandagatla wrote:
>> currently the max rows and cols values are hardcoded. In reality
>> these values depend on the IP version. So get these based on
>> device tree compatible strings.
>>
>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla at linaro.org>
>> ---
>>   drivers/soundwire/qcom.c | 50 ++++++++++++++++++++++++++++------------
>>   1 file changed, 35 insertions(+), 15 deletions(-)
>>
>> diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c
>> index 76963a7bdaa3..1dbf33684470 100644
>> --- a/drivers/soundwire/qcom.c
>> +++ b/drivers/soundwire/qcom.c
>> @@ -66,11 +66,6 @@
>>   #define SWRM_REG_VAL_PACK(data, dev, id, reg)	\
>>   			((reg) | ((id) << 16) | ((dev) << 20) | ((data) << 24))
>>   
>> -#define SWRM_MAX_ROW_VAL	0 /* Rows = 48 */
>> -#define SWRM_DEFAULT_ROWS	48
>> -#define SWRM_MIN_COL_VAL	0 /* Cols = 2 */
>> -#define SWRM_DEFAULT_COL	16
>> -#define SWRM_MAX_COL_VAL	7
>>   #define SWRM_SPECIAL_CMD_ID	0xF
>>   #define MAX_FREQ_NUM		1
>>   #define TIMEOUT_MS		(2 * HZ)
>> @@ -104,6 +99,8 @@ struct qcom_swrm_ctrl {
>>   	unsigned int version;
>>   	int num_din_ports;
>>   	int num_dout_ports;
>> +	int cols_index;
>> +	int rows_index;
>>   	unsigned long dout_port_mask;
>>   	unsigned long din_port_mask;
>>   	struct qcom_swrm_port_config pconfig[QCOM_SDW_MAX_PORTS];
>> @@ -113,6 +110,21 @@ struct qcom_swrm_ctrl {
>>   	int (*reg_write)(struct qcom_swrm_ctrl *ctrl, int reg, int val);
>>   };
>>   
>> +struct qcom_swrm_data {
>> +	u32 default_cols;
>> +	u32 default_rows;
>> +};
>> +
>> +static struct qcom_swrm_data swrm_v1_3_data = {
>> +	.default_rows = 48,
>> +	.default_cols = 16,
>> +};
>> +
>> +static struct qcom_swrm_data swrm_v1_5_data = {
>> +	.default_rows = 50,
>> +	.default_cols = 16,
>> +};
>> +
>>   #define to_qcom_sdw(b)	container_of(b, struct qcom_swrm_ctrl, bus)
>>   
>>   static int qcom_swrm_ahb_reg_read(struct qcom_swrm_ctrl *ctrl, int reg,
>> @@ -299,8 +311,10 @@ static int qcom_swrm_init(struct qcom_swrm_ctrl *ctrl)
>>   	u32 val;
>>   
>>   	/* Clear Rows and Cols */
>> -	val = FIELD_PREP(SWRM_MCP_FRAME_CTRL_BANK_ROW_CTRL_BMSK, SWRM_MAX_ROW_VAL);
>> -	val |= FIELD_PREP(SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_BMSK, SWRM_MIN_COL_VAL);
>> +	val = FIELD_PREP(SWRM_MCP_FRAME_CTRL_BANK_ROW_CTRL_BMSK,
>> +			 ctrl->rows_index);
>> +	val |= FIELD_PREP(SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_BMSK,
>> +			  ctrl->cols_index);
> 
> single line for these ?
My vimrc had this 80 line autowrap thingy which might have done this!!

> 
>>   	ctrl->reg_write(ctrl, SWRM_MCP_FRAME_CTRL_BANK_ADDR(0), val);
>>   
>> @@ -378,8 +392,10 @@ static int qcom_swrm_pre_bank_switch(struct sdw_bus *bus)
>>   	val &= ~SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_BMSK;
>>   	val &= ~SWRM_MCP_FRAME_CTRL_BANK_ROW_CTRL_BMSK;
>>   
>> -	val |= FIELD_PREP(SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_BMSK, SWRM_MAX_COL_VAL);
>> -	val |= FIELD_PREP(SWRM_MCP_FRAME_CTRL_BANK_ROW_CTRL_BMSK, SWRM_MAX_ROW_VAL);
>> +	val |= FIELD_PREP(SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_BMSK,
>> +			  ctrl->cols_index);
>> +	val |= FIELD_PREP(SWRM_MCP_FRAME_CTRL_BANK_ROW_CTRL_BMSK,
>> +			  ctrl->rows_index);
> 
> here as well
> 
>>   
>>   	return ctrl->reg_write(ctrl, reg, val);
>>   }
>> @@ -780,6 +796,7 @@ static int qcom_swrm_probe(struct platform_device *pdev)
>>   	struct sdw_master_prop *prop;
>>   	struct sdw_bus_params *params;
>>   	struct qcom_swrm_ctrl *ctrl;
>> +	const struct qcom_swrm_data *data;
>>   	int ret;
>>   	u32 val;
>>   
>> @@ -787,6 +804,9 @@ static int qcom_swrm_probe(struct platform_device *pdev)
>>   	if (!ctrl)
>>   		return -ENOMEM;
>>   
>> +	data = of_device_get_match_data(dev);
> 
> Wont it be good to check if data is valid, we do dereference it few line
> below
We Should not hit that case as we will never reach here without matching 
compatible!
If you insist, I can add a check but data will be always be valid at the 
time of check!

> 
>> +	ctrl->rows_index = sdw_find_row_index(data->default_rows);
>> +	ctrl->cols_index = sdw_find_col_index(data->default_cols);
>>   #if IS_ENABLED(CONFIG_SLIMBUS)
>>   	if (dev->parent->bus == &slimbus_bus) {
>>   #else
>> @@ -836,8 +856,8 @@ static int qcom_swrm_probe(struct platform_device *pdev)
>>   	params = &ctrl->bus.params;
>>   	params->max_dr_freq = DEFAULT_CLK_FREQ;
>>   	params->curr_dr_freq = DEFAULT_CLK_FREQ;
>> -	params->col = SWRM_DEFAULT_COL;
>> -	params->row = SWRM_DEFAULT_ROWS;
>> +	params->col = data->default_cols;
>> +	params->row = data->default_rows;
>>   	ctrl->reg_read(ctrl, SWRM_MCP_STATUS, &val);
>>   	params->curr_bank = val & SWRM_MCP_STATUS_BANK_NUM_MASK;
>>   	params->next_bank = !params->curr_bank;
>> @@ -847,8 +867,8 @@ static int qcom_swrm_probe(struct platform_device *pdev)
>>   	prop->num_clk_gears = 0;
>>   	prop->num_clk_freq = MAX_FREQ_NUM;
>>   	prop->clk_freq = &qcom_swrm_freq_tbl[0];
>> -	prop->default_col = SWRM_DEFAULT_COL;
>> -	prop->default_row = SWRM_DEFAULT_ROWS;
>> +	prop->default_col = data->default_cols;
>> +	prop->default_row = data->default_rows;
>>   
>>   	ctrl->reg_read(ctrl, SWRM_COMP_HW_VERSION, &ctrl->version);
>>   
>> @@ -899,8 +919,8 @@ static int qcom_swrm_remove(struct platform_device *pdev)
>>   }
>>   
>>   static const struct of_device_id qcom_swrm_of_match[] = {
>> -	{ .compatible = "qcom,soundwire-v1.3.0", },
>> -	{ .compatible = "qcom,soundwire-v1.5.1", },
>> +	{ .compatible = "qcom,soundwire-v1.3.0", .data = &swrm_v1_3_data },
>> +	{ .compatible = "qcom,soundwire-v1.5.1", .data = &swrm_v1_5_data },
>>   	{/* sentinel */},
>>   };
>>   
>> -- 
>> 2.21.0
>