[PATCH V2] ASoC: Intel: boards: Use FS as nau8825 sysclk in nau88125_* machine
Radoslaw Biernacki
rad at semihalf.com
Fri May 1 21:31:41 CEST 2020
This single fix address two issues on machines with nau88125:
1) Audio distortion, due to lack of required clock rate on MCLK line
2) Loud audible "pops" on headphones if there is no sysclk during nau8825
playback power up sequence
Explanation for:
1) Due to Skylake HW limitation, MCLK pin can only output 24MHz clk
rate (it can be only connected to XTAL parent clk). The BCLK pin
can be driven by dividers and therefore FW is able to set it to rate
required by chosen audio format. According to nau8825 datasheet, 256*FS
sysclk gives the best audio quality and the only way to achieve this
(taking into account the above limitations) its to regenerate the MCLK
from BCLK on nau8825 side by FFL. Without required clk rate, audio is
distorted by added harmonics.
2) Currently Skylake does not output MCLK/FS when the back-end DAI op
hw_param is called, so we cannot switch to MCLK/FS in hw_param. This
patch reduces pop by letting nau8825 keep using its internal VCO clock
during widget power up sequence, until SNDRV_PCM_TRIGGER_START when
MCLK/FS is available. Once device resumes, the system will only enable
power sequence for playback without doing hardware parameter, audio
format, and PLL configure. In the mean time, the jack detecion sequence
has changed PLL parameters and switched to internal clock. Thus, the
playback signal distorted without correct PLL parameters. That is why
we need to configure the PLL again in SNDRV_PCM_TRIGGER_RESUME case.
Signed-off-by: John Hsu <KCHSU0 at nuvoton.com>
Signed-off-by: Yong Zhi <yong.zhi at intel.com>
Signed-off-by: Mac Chiang <mac.chiang at intel.com>
Signed-off-by: Ben Zhang <benzh at chromium.org>
Signed-off-by: Radoslaw Biernacki <rad at semihalf.com>
---
.../soc/intel/boards/skl_nau88l25_max98357a.c | 72 +++++++++++++-----
sound/soc/intel/boards/skl_nau88l25_ssm4567.c | 73 ++++++++++++++-----
2 files changed, 107 insertions(+), 38 deletions(-)
diff --git a/sound/soc/intel/boards/skl_nau88l25_max98357a.c b/sound/soc/intel/boards/skl_nau88l25_max98357a.c
index d7b8154c43a4..0f3cea1342d1 100644
--- a/sound/soc/intel/boards/skl_nau88l25_max98357a.c
+++ b/sound/soc/intel/boards/skl_nau88l25_max98357a.c
@@ -8,6 +8,7 @@
#include <linux/module.h>
#include <linux/platform_device.h>
+#include <linux/delay.h>
#include <sound/core.h>
#include <sound/jack.h>
#include <sound/pcm.h>
@@ -47,7 +48,7 @@ enum {
};
static int platform_clock_control(struct snd_soc_dapm_widget *w,
- struct snd_kcontrol *k, int event)
+ struct snd_kcontrol *k, int event)
{
struct snd_soc_dapm_context *dapm = w->dapm;
struct snd_soc_card *card = dapm->card;
@@ -60,14 +61,7 @@ static int platform_clock_control(struct snd_soc_dapm_widget *w,
return -EIO;
}
- if (SND_SOC_DAPM_EVENT_ON(event)) {
- ret = snd_soc_dai_set_sysclk(codec_dai,
- NAU8825_CLK_MCLK, 24000000, SND_SOC_CLOCK_IN);
- if (ret < 0) {
- dev_err(card->dev, "set sysclk err = %d\n", ret);
- return -EIO;
- }
- } else {
+ if (!SND_SOC_DAPM_EVENT_ON(event)) {
ret = snd_soc_dai_set_sysclk(codec_dai,
NAU8825_CLK_INTERNAL, 0, SND_SOC_CLOCK_IN);
if (ret < 0) {
@@ -292,24 +286,40 @@ static const struct snd_soc_ops skylake_nau8825_fe_ops = {
.startup = skl_fe_startup,
};
-static int skylake_nau8825_hw_params(struct snd_pcm_substream *substream,
- struct snd_pcm_hw_params *params)
+static int skylake_nau8825_trigger(struct snd_pcm_substream *substream, int cmd)
{
struct snd_soc_pcm_runtime *rtd = substream->private_data;
+ struct snd_pcm_runtime *runtime = substream->runtime;
struct snd_soc_dai *codec_dai = asoc_rtd_to_codec(rtd, 0);
- int ret;
-
- ret = snd_soc_dai_set_sysclk(codec_dai,
- NAU8825_CLK_MCLK, 24000000, SND_SOC_CLOCK_IN);
+ int ret = 0;
- if (ret < 0)
- dev_err(rtd->dev, "snd_soc_dai_set_sysclk err = %d\n", ret);
+ switch (cmd) {
+ case SNDRV_PCM_TRIGGER_START:
+ ret = snd_soc_dai_set_sysclk(codec_dai, NAU8825_CLK_FLL_FS, 0,
+ SND_SOC_CLOCK_IN);
+ if (ret < 0) {
+ dev_err(codec_dai->dev, "can't set FS clock %d\n", ret);
+ break;
+ }
+ ret = snd_soc_dai_set_pll(codec_dai, 0, 0, runtime->rate,
+ runtime->rate * 256);
+ if (ret < 0)
+ dev_err(codec_dai->dev, "can't set FLL: %d\n", ret);
+ break;
+ case SNDRV_PCM_TRIGGER_RESUME:
+ ret = snd_soc_dai_set_pll(codec_dai, 0, 0, runtime->rate,
+ runtime->rate * 256);
+ if (ret < 0)
+ dev_err(codec_dai->dev, "can't set FLL: %d\n", ret);
+ msleep(20);
+ break;
+ }
return ret;
}
-static const struct snd_soc_ops skylake_nau8825_ops = {
- .hw_params = skylake_nau8825_hw_params,
+static struct snd_soc_ops skylake_nau8825_ops = {
+ .trigger = skylake_nau8825_trigger,
};
static int skylake_dmic_fixup(struct snd_soc_pcm_runtime *rtd,
@@ -630,10 +640,34 @@ static int skylake_card_late_probe(struct snd_soc_card *card)
return hdac_hdmi_jack_port_init(component, &card->dapm);
}
+static int __maybe_unused skylake_nau8825_resume_post(struct snd_soc_card *card)
+{
+ struct snd_soc_dai *codec_dai;
+
+ codec_dai = snd_soc_card_get_codec_dai(card, SKL_NUVOTON_CODEC_DAI);
+ if (!codec_dai) {
+ dev_err(card->dev, "Codec dai not found\n");
+ return -EIO;
+ }
+
+ dev_dbg(codec_dai->dev, "playback_active:%d playback_widget->active:%d codec_dai->rate:%d\n",
+ codec_dai->stream_active[SNDRV_PCM_STREAM_PLAYBACK],
+ codec_dai->playback_widget->active,
+ codec_dai->rate);
+
+ if (codec_dai->stream_active[SNDRV_PCM_STREAM_PLAYBACK] &&
+ codec_dai->playback_widget->active)
+ snd_soc_dai_set_sysclk(codec_dai, NAU8825_CLK_FLL_FS, 0,
+ SND_SOC_CLOCK_IN);
+
+ return 0;
+}
+
/* skylake audio machine driver for SPT + NAU88L25 */
static struct snd_soc_card skylake_audio_card = {
.name = "sklnau8825max",
.owner = THIS_MODULE,
+ .resume_post = skylake_nau8825_resume_post,
.dai_link = skylake_dais,
.num_links = ARRAY_SIZE(skylake_dais),
.controls = skylake_controls,
diff --git a/sound/soc/intel/boards/skl_nau88l25_ssm4567.c b/sound/soc/intel/boards/skl_nau88l25_ssm4567.c
index 4b317bcf6ea0..be44a40067f0 100644
--- a/sound/soc/intel/boards/skl_nau88l25_ssm4567.c
+++ b/sound/soc/intel/boards/skl_nau88l25_ssm4567.c
@@ -12,6 +12,7 @@
#include <linux/module.h>
#include <linux/platform_device.h>
+#include <linux/delay.h>
#include <sound/core.h>
#include <sound/pcm.h>
#include <sound/soc.h>
@@ -57,7 +58,7 @@ static const struct snd_kcontrol_new skylake_controls[] = {
};
static int platform_clock_control(struct snd_soc_dapm_widget *w,
- struct snd_kcontrol *k, int event)
+ struct snd_kcontrol *k, int event)
{
struct snd_soc_dapm_context *dapm = w->dapm;
struct snd_soc_card *card = dapm->card;
@@ -70,14 +71,7 @@ static int platform_clock_control(struct snd_soc_dapm_widget *w,
return -EIO;
}
- if (SND_SOC_DAPM_EVENT_ON(event)) {
- ret = snd_soc_dai_set_sysclk(codec_dai,
- NAU8825_CLK_MCLK, 24000000, SND_SOC_CLOCK_IN);
- if (ret < 0) {
- dev_err(card->dev, "set sysclk err = %d\n", ret);
- return -EIO;
- }
- } else {
+ if (!SND_SOC_DAPM_EVENT_ON(event)) {
ret = snd_soc_dai_set_sysclk(codec_dai,
NAU8825_CLK_INTERNAL, 0, SND_SOC_CLOCK_IN);
if (ret < 0) {
@@ -85,6 +79,7 @@ static int platform_clock_control(struct snd_soc_dapm_widget *w,
return -EIO;
}
}
+
return ret;
}
@@ -344,24 +339,40 @@ static int skylake_dmic_fixup(struct snd_soc_pcm_runtime *rtd,
return 0;
}
-static int skylake_nau8825_hw_params(struct snd_pcm_substream *substream,
- struct snd_pcm_hw_params *params)
+static int skylake_nau8825_trigger(struct snd_pcm_substream *substream, int cmd)
{
struct snd_soc_pcm_runtime *rtd = substream->private_data;
+ struct snd_pcm_runtime *runtime = substream->runtime;
struct snd_soc_dai *codec_dai = asoc_rtd_to_codec(rtd, 0);
- int ret;
-
- ret = snd_soc_dai_set_sysclk(codec_dai,
- NAU8825_CLK_MCLK, 24000000, SND_SOC_CLOCK_IN);
+ int ret = 0;
- if (ret < 0)
- dev_err(rtd->dev, "snd_soc_dai_set_sysclk err = %d\n", ret);
+ switch (cmd) {
+ case SNDRV_PCM_TRIGGER_START:
+ ret = snd_soc_dai_set_sysclk(codec_dai, NAU8825_CLK_FLL_FS, 0,
+ SND_SOC_CLOCK_IN);
+ if (ret < 0) {
+ dev_err(codec_dai->dev, "can't set FS clock %d\n", ret);
+ break;
+ }
+ ret = snd_soc_dai_set_pll(codec_dai, 0, 0, runtime->rate,
+ runtime->rate * 256);
+ if (ret < 0)
+ dev_err(codec_dai->dev, "can't set FLL: %d\n", ret);
+ break;
+ case SNDRV_PCM_TRIGGER_RESUME:
+ ret = snd_soc_dai_set_pll(codec_dai, 0, 0, runtime->rate,
+ runtime->rate * 256);
+ if (ret < 0)
+ dev_err(codec_dai->dev, "can't set FLL: %d\n", ret);
+ msleep(20);
+ break;
+ }
return ret;
}
-static const struct snd_soc_ops skylake_nau8825_ops = {
- .hw_params = skylake_nau8825_hw_params,
+static struct snd_soc_ops skylake_nau8825_ops = {
+ .trigger = skylake_nau8825_trigger,
};
static const unsigned int channels_dmic[] = {
@@ -671,10 +682,34 @@ static int skylake_card_late_probe(struct snd_soc_card *card)
return hdac_hdmi_jack_port_init(component, &card->dapm);
}
+static int __maybe_unused skylake_nau8825_resume_post(struct snd_soc_card *card)
+{
+ struct snd_soc_dai *codec_dai;
+
+ codec_dai = snd_soc_card_get_codec_dai(card, SKL_NUVOTON_CODEC_DAI);
+ if (!codec_dai) {
+ dev_err(card->dev, "Codec dai not found\n");
+ return -EIO;
+ }
+
+ dev_dbg(codec_dai->dev, "playback_active:%d playback_widget->active:%d codec_dai->rate:%d\n",
+ codec_dai->stream_active[SNDRV_PCM_STREAM_PLAYBACK],
+ codec_dai->playback_widget->active,
+ codec_dai->rate);
+
+ if (codec_dai->stream_active[SNDRV_PCM_STREAM_PLAYBACK] &&
+ codec_dai->playback_widget->active)
+ snd_soc_dai_set_sysclk(codec_dai, NAU8825_CLK_FLL_FS, 0,
+ SND_SOC_CLOCK_IN);
+
+ return 0;
+}
+
/* skylake audio machine driver for SPT + NAU88L25 */
static struct snd_soc_card skylake_audio_card = {
.name = "sklnau8825adi",
.owner = THIS_MODULE,
+ .resume_post = skylake_nau8825_resume_post,
.dai_link = skylake_dais,
.num_links = ARRAY_SIZE(skylake_dais),
.controls = skylake_controls,
--
2.17.1
More information about the Alsa-devel
mailing list