[PATCH] sound: pci: delete repeated words in comments

Randy Dunlap rdunlap at infradead.org
Thu Aug 6 04:19:26 CEST 2020


Drop duplicated words in sound/pci/.
{and, the, at}

Signed-off-by: Randy Dunlap <rdunlap at infradead.org>
Cc: Jaroslav Kysela <perex at perex.cz>
Cc: Takashi Iwai <tiwai at suse.com>
Cc: alsa-devel at alsa-project.org
Cc: Clemens Ladisch <clemens at ladisch.de>
---
 sound/pci/cs46xx/cs46xx_lib.c       |    2 +-
 sound/pci/cs46xx/dsp_spos_scb_lib.c |    2 +-
 sound/pci/hda/hda_codec.c           |    2 +-
 sound/pci/hda/hda_generic.c         |    2 +-
 sound/pci/hda/patch_sigmatel.c      |    2 +-
 sound/pci/ice1712/prodigy192.c      |    2 +-
 sound/pci/oxygen/xonar_dg.c         |    2 +-
 7 files changed, 7 insertions(+), 7 deletions(-)

--- linux-next-20200805.orig/sound/pci/cs46xx/cs46xx_lib.c
+++ linux-next-20200805/sound/pci/cs46xx/cs46xx_lib.c
@@ -766,7 +766,7 @@ static void snd_cs46xx_set_capture_sampl
 		rate = 48000 / 9;
 
 	/*
-	 *  We can not capture at at rate greater than the Input Rate (48000).
+	 *  We can not capture at a rate greater than the Input Rate (48000).
 	 *  Return an error if an attempt is made to stray outside that limit.
 	 */
 	if (rate > 48000)
--- linux-next-20200805.orig/sound/pci/cs46xx/dsp_spos_scb_lib.c
+++ linux-next-20200805/sound/pci/cs46xx/dsp_spos_scb_lib.c
@@ -1716,7 +1716,7 @@ int cs46xx_iec958_pre_open (struct snd_c
 	struct dsp_spos_instance * ins = chip->dsp_spos_instance;
 
 	if ( ins->spdif_status_out & DSP_SPDIF_STATUS_OUTPUT_ENABLED ) {
-		/* remove AsynchFGTxSCB and and PCMSerialInput_II */
+		/* remove AsynchFGTxSCB and PCMSerialInput_II */
 		cs46xx_dsp_disable_spdif_out (chip);
 
 		/* save state */
--- linux-next-20200805.orig/sound/pci/hda/hda_codec.c
+++ linux-next-20200805/sound/pci/hda/hda_codec.c
@@ -3428,7 +3428,7 @@ EXPORT_SYMBOL_GPL(snd_hda_set_power_save
  * @nid: NID to check / update
  *
  * Check whether the given NID is in the amp list.  If it's in the list,
- * check the current AMP status, and update the the power-status according
+ * check the current AMP status, and update the power-status according
  * to the mute status.
  *
  * This function is supposed to be set or called from the check_power_status
--- linux-next-20200805.orig/sound/pci/hda/hda_generic.c
+++ linux-next-20200805/sound/pci/hda/hda_generic.c
@@ -813,7 +813,7 @@ static void activate_amp_in(struct hda_c
 	}
 }
 
-/* sync power of each widget in the the given path */
+/* sync power of each widget in the given path */
 static hda_nid_t path_power_update(struct hda_codec *codec,
 				   struct nid_path *path,
 				   bool allow_powerdown)
--- linux-next-20200805.orig/sound/pci/hda/patch_sigmatel.c
+++ linux-next-20200805/sound/pci/hda/patch_sigmatel.c
@@ -838,7 +838,7 @@ static int stac_auto_create_beep_ctls(st
 	static const struct snd_kcontrol_new beep_vol_ctl =
 		HDA_CODEC_VOLUME(NULL, 0, 0, 0);
 
-	/* check for mute support for the the amp */
+	/* check for mute support for the amp */
 	if ((caps & AC_AMPCAP_MUTE) >> AC_AMPCAP_MUTE_SHIFT) {
 		const struct snd_kcontrol_new *temp;
 		if (spec->anabeep_nid == nid)
--- linux-next-20200805.orig/sound/pci/ice1712/prodigy192.c
+++ linux-next-20200805/sound/pci/ice1712/prodigy192.c
@@ -32,7 +32,7 @@
  *		  Experimentally I found out that only a combination of
  *		  OCKS0=1, OCKS1=1 (128fs, 64fs output) and ice1724 -
  *		  VT1724_MT_I2S_MCLK_128X=0 (256fs input) yields correct
- *		  sampling rate. That means the the FPGA doubles the
+ *		  sampling rate. That means that the FPGA doubles the
  *		  MCK01 rate.
  *
  *	Copyright (c) 2003 Takashi Iwai <tiwai at suse.de>
--- linux-next-20200805.orig/sound/pci/oxygen/xonar_dg.c
+++ linux-next-20200805/sound/pci/oxygen/xonar_dg.c
@@ -29,7 +29,7 @@
  *   GPIO 4 <- headphone detect
  *   GPIO 5 -> enable ADC analog circuit for the left channel
  *   GPIO 6 -> enable ADC analog circuit for the right channel
- *   GPIO 7 -> switch green rear output jack between CS4245 and and the first
+ *   GPIO 7 -> switch green rear output jack between CS4245 and the first
  *             channel of CS4361 (mechanical relay)
  *   GPIO 8 -> enable output to speakers
  *


More information about the Alsa-devel mailing list