[alsa-devel] [PATCH v4 1/3] ASoC: rt5677: allow multiple interrupt sources
Curtis Malainey
cujomalainey at chromium.org
Tue May 7 23:10:26 CEST 2019
On Fri, May 3, 2019 at 4:10 PM Fletcher Woodruff <fletcherw at chromium.org>
wrote:
> From: Ben Zhang <benzh at chromium.org>
>
> This patch allows headphone plug detect and mic present
> detect to be enabled at the same time. This patch implements
> an irq_chip with irq_domain directly instead of using
> regmap-irq, so that interrupt source line polarities can
> be flipped to support irq sharing.
>
> This patch does not add polarity flipping support within regmap-irq
> because there is extra work that must be done within the irq handler
> to support hotword detection. On the Chromebook Pixel, the firmware will
> disconnect GPIO1 from the jack detection irq when a hotword is detected
> and trigger the interrupt handler. Inside the handler, we will need to
> detect this, report the hotword event, and re-connect GPIO1 to the jack
> detection irq.
>
> Signed-off-by: Ben Zhang <benzh at chromium.org>
> Signed-off-by: Fletcher Woodruff <fletcherw at chromium.org>
> ---
> sound/soc/codecs/rt5677.c | 256 ++++++++++++++++++++++++++++----------
> sound/soc/codecs/rt5677.h | 14 ++-
> 2 files changed, 203 insertions(+), 67 deletions(-)
>
> diff --git a/sound/soc/codecs/rt5677.c b/sound/soc/codecs/rt5677.c
> index 9b7a1833d3316c..899e07e30228a1 100644
> --- a/sound/soc/codecs/rt5677.c
> +++ b/sound/soc/codecs/rt5677.c
> @@ -23,6 +23,10 @@
> #include <linux/firmware.h>
> #include <linux/of_device.h>
> #include <linux/property.h>
> +#include <linux/irq.h>
> +#include <linux/interrupt.h>
> +#include <linux/irqdomain.h>
> +#include <linux/workqueue.h>
> #include <sound/core.h>
> #include <sound/pcm.h>
> #include <sound/pcm_params.h>
> @@ -4620,7 +4624,6 @@ static void rt5677_gpio_config(struct rt5677_priv
> *rt5677, unsigned offset,
> static int rt5677_to_irq(struct gpio_chip *chip, unsigned offset)
> {
> struct rt5677_priv *rt5677 = gpiochip_get_data(chip);
> - struct regmap_irq_chip_data *data = rt5677->irq_data;
> int irq;
>
> if ((rt5677->pdata.jd1_gpio == 1 && offset == RT5677_GPIO1) ||
> @@ -4646,7 +4649,7 @@ static int rt5677_to_irq(struct gpio_chip *chip,
> unsigned offset)
> return -ENXIO;
> }
>
> - return regmap_irq_get_virq(data, irq);
> + return irq_create_mapping(rt5677->domain, irq);
> }
>
> static const struct gpio_chip rt5677_template_chip = {
> @@ -4716,37 +4719,13 @@ static int rt5677_probe(struct snd_soc_component
> *component)
>
> snd_soc_component_force_bias_level(component, SND_SOC_BIAS_OFF);
>
> - regmap_write(rt5677->regmap, RT5677_DIG_MISC, 0x0020);
> + regmap_update_bits(rt5677->regmap, RT5677_DIG_MISC,
> + ~RT5677_IRQ_DEBOUNCE_SEL_MASK, 0x0020);
> regmap_write(rt5677->regmap, RT5677_PWR_DSP2, 0x0c00);
>
> for (i = 0; i < RT5677_GPIO_NUM; i++)
> rt5677_gpio_config(rt5677, i,
> rt5677->pdata.gpio_config[i]);
>
> - if (rt5677->irq_data) {
> - regmap_update_bits(rt5677->regmap, RT5677_GPIO_CTRL1,
> 0x8000,
> - 0x8000);
> - regmap_update_bits(rt5677->regmap, RT5677_DIG_MISC, 0x0018,
> - 0x0008);
> -
> - if (rt5677->pdata.jd1_gpio)
> - regmap_update_bits(rt5677->regmap, RT5677_JD_CTRL1,
> - RT5677_SEL_GPIO_JD1_MASK,
> - rt5677->pdata.jd1_gpio <<
> - RT5677_SEL_GPIO_JD1_SFT);
> -
> - if (rt5677->pdata.jd2_gpio)
> - regmap_update_bits(rt5677->regmap, RT5677_JD_CTRL1,
> - RT5677_SEL_GPIO_JD2_MASK,
> - rt5677->pdata.jd2_gpio <<
> - RT5677_SEL_GPIO_JD2_SFT);
> -
> - if (rt5677->pdata.jd3_gpio)
> - regmap_update_bits(rt5677->regmap, RT5677_JD_CTRL1,
> - RT5677_SEL_GPIO_JD3_MASK,
> - rt5677->pdata.jd3_gpio <<
> - RT5677_SEL_GPIO_JD3_SFT);
> - }
> -
> mutex_init(&rt5677->dsp_cmd_lock);
> mutex_init(&rt5677->dsp_pri_lock);
>
> @@ -5063,65 +5042,210 @@ static void rt5677_read_device_properties(struct
> rt5677_priv *rt5677,
> &rt5677->pdata.jd3_gpio);
> }
>
> -static struct regmap_irq rt5677_irqs[] = {
> +struct rt5677_irq_desc {
> + unsigned int enable_mask;
> + unsigned int status_mask;
> + unsigned int polarity_mask;
> +};
> +
> +static const struct rt5677_irq_desc rt5677_irq_descs[] = {
> [RT5677_IRQ_JD1] = {
> - .reg_offset = 0,
> - .mask = RT5677_EN_IRQ_GPIO_JD1,
> + .enable_mask = RT5677_EN_IRQ_GPIO_JD1,
> + .status_mask = RT5677_STA_GPIO_JD1,
> + .polarity_mask = RT5677_INV_GPIO_JD1,
> },
> [RT5677_IRQ_JD2] = {
> - .reg_offset = 0,
> - .mask = RT5677_EN_IRQ_GPIO_JD2,
> + .enable_mask = RT5677_EN_IRQ_GPIO_JD2,
> + .status_mask = RT5677_STA_GPIO_JD2,
> + .polarity_mask = RT5677_INV_GPIO_JD2,
> },
> [RT5677_IRQ_JD3] = {
> - .reg_offset = 0,
> - .mask = RT5677_EN_IRQ_GPIO_JD3,
> + .enable_mask = RT5677_EN_IRQ_GPIO_JD3,
> + .status_mask = RT5677_STA_GPIO_JD3,
> + .polarity_mask = RT5677_INV_GPIO_JD3,
> },
> };
>
> -static struct regmap_irq_chip rt5677_irq_chip = {
> - .name = "rt5677",
> - .irqs = rt5677_irqs,
> - .num_irqs = ARRAY_SIZE(rt5677_irqs),
> +static irqreturn_t rt5677_irq(int unused, void *data)
> +{
> + struct rt5677_priv *rt5677 = data;
> + int ret = 0, i, reg_irq, virq;
> + bool irq_fired;
> +
> + mutex_lock(&rt5677->irq_lock);
> + /* Read interrupt status */
> + ret = regmap_read(rt5677->regmap, RT5677_IRQ_CTRL1, ®_irq);
> + if (ret) {
> + dev_err(rt5677->component->dev,
> + "Failed to read IRQ status: %d\n",
> + ret);
> + goto exit;
> + }
> + /*
> + * Clear the interrupt by flipping the polarity of the
> + * interrupt source lines that just fired
> + */
> + irq_fired = false;
> + for (i = 0; i < RT5677_IRQ_NUM; i++) {
> + if (reg_irq & rt5677_irq_descs[i].status_mask) {
> + reg_irq ^= rt5677_irq_descs[i].polarity_mask;
> + irq_fired = true;
> + }
> + }
> + if (!irq_fired)
> + goto exit;
>
> - .num_regs = 1,
> - .status_base = RT5677_IRQ_CTRL1,
> - .mask_base = RT5677_IRQ_CTRL1,
> - .mask_invert = 1,
> -};
> + ret = regmap_write(rt5677->regmap, RT5677_IRQ_CTRL1, reg_irq);
> + if (ret) {
> + dev_err(rt5677->component->dev,
> + "Failed to update IRQ status: %d\n",
> + ret);
> + goto exit;
> + }
> +
> + /* Process interrupts */
> + for (i = 0; i < RT5677_IRQ_NUM; i++) {
> + if ((reg_irq & rt5677_irq_descs[i].enable_mask) &&
> + (reg_irq & rt5677_irq_descs[i].status_mask)) {
> + virq = irq_find_mapping(rt5677->domain, i);
> + if (virq)
> + handle_nested_irq(virq);
> + }
> + }
> +exit:
> + mutex_unlock(&rt5677->irq_lock);
> + return IRQ_HANDLED;
> +}
>
> -static int rt5677_init_irq(struct i2c_client *i2c)
> +static void rt5677_irq_work(struct work_struct *work)
> {
> - int ret;
> - struct rt5677_priv *rt5677 = i2c_get_clientdata(i2c);
> + struct rt5677_priv *rt5677 =
> + container_of(work, struct rt5677_priv, irq_work.work);
>
> - if (!rt5677->pdata.jd1_gpio &&
> - !rt5677->pdata.jd2_gpio &&
> - !rt5677->pdata.jd3_gpio)
> - return 0;
> + rt5677_irq(0, rt5677);
> +}
>
> - if (!i2c->irq) {
> - dev_err(&i2c->dev, "No interrupt specified\n");
> - return -EINVAL;
> - }
> +static void rt5677_irq_bus_lock(struct irq_data *data)
> +{
> + struct rt5677_priv *rt5677 = irq_data_get_irq_chip_data(data);
>
> - ret = regmap_add_irq_chip(rt5677->regmap, i2c->irq,
> - IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
> 0,
> - &rt5677_irq_chip, &rt5677->irq_data);
> + mutex_lock(&rt5677->irq_lock);
> +}
>
> - if (ret != 0) {
> - dev_err(&i2c->dev, "Failed to register IRQ chip: %d\n",
> ret);
> - return ret;
> - }
> +static void rt5677_irq_bus_sync_unlock(struct irq_data *data)
> +{
> + struct rt5677_priv *rt5677 = irq_data_get_irq_chip_data(data);
> +
> + regmap_update_bits(rt5677->regmap, RT5677_IRQ_CTRL1,
> + RT5677_EN_IRQ_GPIO_JD1 | RT5677_EN_IRQ_GPIO_JD2 |
> + RT5677_EN_IRQ_GPIO_JD3, rt5677->irq_en);
> + mutex_unlock(&rt5677->irq_lock);
> +}
>
> +static void rt5677_irq_enable(struct irq_data *data)
> +{
> + struct rt5677_priv *rt5677 = irq_data_get_irq_chip_data(data);
> +
> + rt5677->irq_en |= rt5677_irq_descs[data->hwirq].enable_mask;
> +}
> +
> +static void rt5677_irq_disable(struct irq_data *data)
> +{
> + struct rt5677_priv *rt5677 = irq_data_get_irq_chip_data(data);
> +
> + rt5677->irq_en &= ~rt5677_irq_descs[data->hwirq].enable_mask;
> +}
> +
> +static struct irq_chip rt5677_irq_chip = {
> + .name = "rt5677_irq_chip",
> + .irq_bus_lock = rt5677_irq_bus_lock,
> + .irq_bus_sync_unlock = rt5677_irq_bus_sync_unlock,
> + .irq_disable = rt5677_irq_disable,
> + .irq_enable = rt5677_irq_enable,
> +};
> +
> +static int rt5677_irq_map(struct irq_domain *h, unsigned int virq,
> + irq_hw_number_t hw)
> +{
> + struct rt5677_priv *rt5677 = h->host_data;
> +
> + irq_set_chip_data(virq, rt5677);
> + irq_set_chip(virq, &rt5677_irq_chip);
> + irq_set_nested_thread(virq, 1);
> + irq_set_noprobe(virq);
> return 0;
> }
>
> -static void rt5677_free_irq(struct i2c_client *i2c)
> +
> +static const struct irq_domain_ops rt5677_domain_ops = {
> + .map = rt5677_irq_map,
> + .xlate = irq_domain_xlate_twocell,
> +};
> +
> +static void rt5677_init_irq(struct i2c_client *i2c)
> +{
> + struct rt5677_priv *rt5677 = i2c_get_clientdata(i2c);
> + int ret;
> + unsigned int jd_mask = 0, jd_val = 0;
> +
> + /* No irq has been assigned to the codec */
> + if (!i2c->irq)
> + return;
> +
> + mutex_init(&rt5677->irq_lock);
> + INIT_DELAYED_WORK(&rt5677->irq_work, rt5677_irq_work);
> +
> + /*
> + * Select RC as the debounce clock so that GPIO works even when
> + * MCLK is gated which happens when there is no audio stream
> + * (SND_SOC_BIAS_OFF).
> + */
> + regmap_update_bits(rt5677->regmap, RT5677_DIG_MISC,
> + RT5677_IRQ_DEBOUNCE_SEL_MASK,
> + RT5677_IRQ_DEBOUNCE_SEL_RC);
> + /* Enable auto power on RC when GPIO states are changed */
> + regmap_update_bits(rt5677->regmap, RT5677_GEN_CTRL1, 0xff, 0xff);
> +
> + /* Select and enable jack detection sources per platform data */
> + if (rt5677->pdata.jd1_gpio) {
> + jd_mask |= RT5677_SEL_GPIO_JD1_MASK;
> + jd_val |= rt5677->pdata.jd1_gpio <<
> RT5677_SEL_GPIO_JD1_SFT;
> + }
> + if (rt5677->pdata.jd2_gpio) {
> + jd_mask |= RT5677_SEL_GPIO_JD2_MASK;
> + jd_val |= rt5677->pdata.jd2_gpio <<
> RT5677_SEL_GPIO_JD2_SFT;
> + }
> + if (rt5677->pdata.jd3_gpio) {
> + jd_mask |= RT5677_SEL_GPIO_JD3_MASK;
> + jd_val |= rt5677->pdata.jd3_gpio <<
> RT5677_SEL_GPIO_JD3_SFT;
> + }
> + regmap_update_bits(rt5677->regmap, RT5677_JD_CTRL1, jd_mask,
> jd_val);
> +
> + /* Set GPIO1 pin to be IRQ output */
> + regmap_update_bits(rt5677->regmap, RT5677_GPIO_CTRL1,
> + RT5677_GPIO1_PIN_MASK, RT5677_GPIO1_PIN_IRQ);
> +
> + /* Ready to listen for interrupts */
> + rt5677->domain = irq_domain_add_linear(i2c->dev.of_node,
> + RT5677_IRQ_NUM, &rt5677_domain_ops, rt5677);
> + if (!rt5677->domain) {
> + dev_err(&i2c->dev, "Failed to create IRQ domain\n");
> + return;
> + }
> + ret = devm_request_threaded_irq(&i2c->dev, i2c->irq, NULL,
> rt5677_irq,
> + IRQF_TRIGGER_RISING | IRQF_ONESHOT,
> + "rt5677", i2c);
>
Something is a bit weird here, you are passing in the i2c device type for
the irq but reading out the rt5677_priv in the interrupt. This is causing
KASAN errors.
> + if (ret) {
> + dev_err(&i2c->dev, "Failed to request IRQ: %d\n", ret);
> + return;
> + }
> +}
> +
> +static void rt5677_irq_exit(struct i2c_client *i2c)
> {
> struct rt5677_priv *rt5677 = i2c_get_clientdata(i2c);
>
> - if (rt5677->irq_data)
> - regmap_del_irq_chip(i2c->irq, rt5677->irq_data);
> + cancel_delayed_work_sync(&rt5677->irq_work);
> }
>
> static int rt5677_i2c_probe(struct i2c_client *i2c)
> @@ -5259,7 +5383,7 @@ static int rt5677_i2c_probe(struct i2c_client *i2c)
>
> static int rt5677_i2c_remove(struct i2c_client *i2c)
> {
> - rt5677_free_irq(i2c);
> + rt5677_irq_exit(i2c);
> rt5677_free_gpio(i2c);
>
> return 0;
> diff --git a/sound/soc/codecs/rt5677.h b/sound/soc/codecs/rt5677.h
> index 183d92b030459f..9c73bea8635508 100644
> --- a/sound/soc/codecs/rt5677.h
> +++ b/sound/soc/codecs/rt5677.h
> @@ -1636,6 +1636,12 @@
> #define RT5677_GPIO6_P_NOR (0x0 << 0)
> #define RT5677_GPIO6_P_INV (0x1 << 0)
>
> +/* General Control (0xfa) */
> +#define RT5677_IRQ_DEBOUNCE_SEL_MASK (0x3 << 3)
> +#define RT5677_IRQ_DEBOUNCE_SEL_MCLK (0x0 << 3)
> +#define RT5677_IRQ_DEBOUNCE_SEL_RC (0x1 << 3)
> +#define RT5677_IRQ_DEBOUNCE_SEL_SLIM (0x2 << 3)
> +
> /* Virtual DSP Mixer Control (0xf7 0xf8 0xf9) */
> #define RT5677_DSP_IB_01_H (0x1 << 15)
> #define RT5677_DSP_IB_01_H_SFT 15
> @@ -1713,6 +1719,7 @@ enum {
> RT5677_IRQ_JD1,
> RT5677_IRQ_JD2,
> RT5677_IRQ_JD3,
> + RT5677_IRQ_NUM,
> };
>
> enum rt5677_type {
> @@ -1811,9 +1818,14 @@ struct rt5677_priv {
> struct gpio_chip gpio_chip;
> #endif
> bool dsp_vad_en;
> - struct regmap_irq_chip_data *irq_data;
> bool is_dsp_mode;
> bool is_vref_slow;
> +
> + /* Interrupt handling */
> + struct irq_domain *domain;
> + struct mutex irq_lock;
> + unsigned int irq_en;
> + struct delayed_work irq_work;
> };
>
> int rt5677_sel_asrc_clk_src(struct snd_soc_component *component,
> --
> 2.21.0.1020.gf2820cf01a-goog
>
> _______________________________________________
> Alsa-devel mailing list
> Alsa-devel at alsa-project.org
> https://mailman.alsa-project.org/mailman/listinfo/alsa-devel
>
More information about the Alsa-devel
mailing list