[alsa-devel] [RESEND PATCH v3 29/30] mfd: cros_ec: Add Management API entry points

[Gwendal Grignou]

Add commands for test and management.
Add command space for future development.

Acked-by: Enric Balletbo i Serra <enric.balletbo at collabora.com>
Acked-by: Benson Leung <bleung at chromium.org>
Reviewed-by: Fabien Lahoudere <fabien.lahoudere at collabora.com>
Signed-off-by: Gwendal Grignou <gwendal at chromium.org>
---
 include/linux/mfd/cros_ec_commands.h | 113 +++++++++++++++++++++++++++
 1 file changed, 113 insertions(+)

diff --git a/include/linux/mfd/cros_ec_commands.h b/include/linux/mfd/cros_ec_commands.h
index 860a76274334..fc8babce1576 100644
--- a/include/linux/mfd/cros_ec_commands.h
+++ b/include/linux/mfd/cros_ec_commands.h
@@ -5176,6 +5176,119 @@ struct ec_params_set_cbi {
 	uint8_t data[];		/* For string and raw data */
 } __ec_align1;
 
+/*
+ * Information about resets of the AP by the EC and the EC's own uptime.
+ */
+#define EC_CMD_GET_UPTIME_INFO 0x0121
+
+struct ec_response_uptime_info {
+	/*
+	 * Number of milliseconds since the last EC boot. Sysjump resets
+	 * typically do not restart the EC's time_since_boot epoch.
+	 *
+	 * WARNING: The EC's sense of time is much less accurate than the AP's
+	 * sense of time, in both phase and frequency.  This timebase is similar
+	 * to CLOCK_MONOTONIC_RAW, but with 1% or more frequency error.
+	 */
+	uint32_t time_since_ec_boot_ms;
+
+	/*
+	 * Number of times the AP was reset by the EC since the last EC boot.
+	 * Note that the AP may be held in reset by the EC during the initial
+	 * boot sequence, such that the very first AP boot may count as more
+	 * than one here.
+	 */
+	uint32_t ap_resets_since_ec_boot;
+
+	/*
+	 * The set of flags which describe the EC's most recent reset.  See
+	 * include/system.h RESET_FLAG_* for details.
+	 */
+	uint32_t ec_reset_flags;
+
+	/* Empty log entries have both the cause and timestamp set to zero. */
+	struct ap_reset_log_entry {
+		/*
+		 * See include/chipset.h: enum chipset_{reset,shutdown}_reason
+		 * for details.
+		 */
+		uint16_t reset_cause;
+
+		/* Reserved for protocol growth. */
+		uint16_t reserved;
+
+		/*
+		 * The time of the reset's assertion, in milliseconds since the
+		 * last EC boot, in the same epoch as time_since_ec_boot_ms.
+		 * Set to zero if the log entry is empty.
+		 */
+		uint32_t reset_time_ms;
+	} recent_ap_reset[4];
+} __ec_align4;
+
+/*
+ * Add entropy to the device secret (stored in the rollback region).
+ *
+ * Depending on the chip, the operation may take a long time (e.g. to erase
+ * flash), so the commands are asynchronous.
+ */
+#define EC_CMD_ADD_ENTROPY	0x0122
+
+enum add_entropy_action {
+	/* Add entropy to the current secret. */
+	ADD_ENTROPY_ASYNC = 0,
+	/*
+	 * Add entropy, and also make sure that the previous secret is erased.
+	 * (this can be implemented by adding entropy multiple times until
+	 * all rolback blocks have been overwritten).
+	 */
+	ADD_ENTROPY_RESET_ASYNC = 1,
+	/* Read back result from the previous operation. */
+	ADD_ENTROPY_GET_RESULT = 2,
+};
+
+struct ec_params_rollback_add_entropy {
+	uint8_t action;
+} __ec_align1;
+
+/*
+ * Perform a single read of a given ADC channel.
+ */
+#define EC_CMD_ADC_READ		0x0123
+
+struct ec_params_adc_read {
+	uint8_t adc_channel;
+} __ec_align1;
+
+struct ec_response_adc_read {
+	int32_t adc_value;
+} __ec_align4;
+
+/*
+ * Read back rollback info
+ */
+#define EC_CMD_ROLLBACK_INFO		0x0124
+
+struct ec_response_rollback_info {
+	int32_t id; /* Incrementing number to indicate which region to use. */
+	int32_t rollback_min_version;
+	int32_t rw_rollback_version;
+} __ec_align4;
+
+
+/* Issue AP reset */
+#define EC_CMD_AP_RESET 0x0125
+
+/*****************************************************************************/
+/* The command range 0x200-0x2FF is reserved for Rotor. */
+
+/*****************************************************************************/
+/*
+ * Reserve a range of host commands for the CR51 firmware.
+ */
+#define EC_CMD_CR51_BASE 0x0300
+#define EC_CMD_CR51_LAST 0x03FF
+
 /*****************************************************************************/
 /* Fingerprint MCU commands: range 0x0400-0x040x */
 
-- 
2.21.0.1020.gf2820cf01a-goog