[alsa-devel] [PATCH v2] ALSA: hda/tegra: enable clock during probe

[Takashi Iwai]

On Thu, 31 Jan 2019 12:05:30 +0100,
Thierry Reding wrote:
> 
> On Wed, Jan 30, 2019 at 05:40:42PM +0100, Takashi Iwai wrote:
> > On Wed, 30 Jan 2019 13:45:49 +0100,
> > Jon Hunter wrote:
> > > 
> > > 
> > > On 25/01/2019 11:06, Sameer Pujar wrote:
> > > > If CONFIG_PM is disabled or runtime PM calls are forbidden, the clocks
> > > > will not be ON. This could cause issue during probe, where hda init
> > > > setup is done. This patch enables clocks unconditionally during probe.
> > > > 
> > > > Along with above, follwoing changes are done.
> > > >   * enable runtime PM before exiting from probe work. This helps to avoid
> > > >     usage of pm_runtime_get_sync/pm_runtime_put() in probe work.
> > > >   * hda_tegra_disable_clocks() is moved out of CONFIG_PM_SLEEP check.
> > > >   * runtime PM callbacks moved out of CONFIG_PM check
> > > > 
> > > > Signed-off-by: Sameer Pujar <spujar at nvidia.com>
> > > > Reviewed-by: Ravindra Lokhande <rlokhande at nvidia.com>
> > > > Reviewed-by: Jon Hunter <jonathanh at nvidia.com>
> > > > ---
> > > >  sound/pci/hda/hda_tegra.c | 26 +++++++++++++++++---------
> > > >  1 file changed, 17 insertions(+), 9 deletions(-)
> > > > 
> > > > diff --git a/sound/pci/hda/hda_tegra.c b/sound/pci/hda/hda_tegra.c
> > > > index c8d18dc..ba6175f 100644
> > > > --- a/sound/pci/hda/hda_tegra.c
> > > > +++ b/sound/pci/hda/hda_tegra.c
> > > > @@ -219,7 +219,6 @@ static int hda_tegra_enable_clocks(struct hda_tegra *data)
> > > >  	return rc;
> > > >  }
> > > >  
> > > > -#ifdef CONFIG_PM_SLEEP
> > > >  static void hda_tegra_disable_clocks(struct hda_tegra *data)
> > > >  {
> > > >  	clk_disable_unprepare(data->hda2hdmi_clk);
> > > > @@ -227,6 +226,7 @@ static void hda_tegra_disable_clocks(struct hda_tegra *data)
> > > >  	clk_disable_unprepare(data->hda_clk);
> > > >  }
> > > >  
> > > > +#ifdef CONFIG_PM_SLEEP
> > > >  /*
> > > >   * power management
> > > >   */
> > > > @@ -257,7 +257,6 @@ static int hda_tegra_resume(struct device *dev)
> > > >  }
> > > >  #endif /* CONFIG_PM_SLEEP */
> > > >  
> > > > -#ifdef CONFIG_PM
> > > >  static int hda_tegra_runtime_suspend(struct device *dev)
> > > >  {
> > > >  	struct snd_card *card = dev_get_drvdata(dev);
> > > > @@ -283,7 +282,7 @@ static int hda_tegra_runtime_resume(struct device *dev)
> > > >  	int rc;
> > > >  
> > > >  	rc = hda_tegra_enable_clocks(hda);
> > > > -	if (rc != 0)
> > > > +	if (rc)
> > > >  		return rc;
> > > >  	if (chip && chip->running) {
> > > >  		hda_tegra_init(hda);
> > > > @@ -292,7 +291,6 @@ static int hda_tegra_runtime_resume(struct device *dev)
> > > >  
> > > >  	return 0;
> > > >  }
> > > > -#endif /* CONFIG_PM */
> > > >  
> > > >  static const struct dev_pm_ops hda_tegra_pm = {
> > > >  	SET_SYSTEM_SLEEP_PM_OPS(hda_tegra_suspend, hda_tegra_resume)
> > > > @@ -551,9 +549,9 @@ static int hda_tegra_probe(struct platform_device *pdev)
> > > >  
> > > >  	dev_set_drvdata(&pdev->dev, card);
> > > >  
> > > > -	pm_runtime_enable(hda->dev);
> > > > -	if (!azx_has_pm_runtime(chip))
> > > > -		pm_runtime_forbid(hda->dev);
> > > > +	err = hda_tegra_enable_clocks(hda);
> > > > +	if (err)
> > > > +		goto out_free;
> > > 
> > > We also need to think about power-domains here. Enabling the clocks
> > > might not be enough as the appropriate power-domain needs to be enabled.
> > > For 64-bit Tegra runtime-pm will handle the power-domains (assuming they
> > > are populated in device-tree). So I still think it is better we call
> > > pm_runtime_get_sync() at some point rather than just replying on
> > > enabling the clocks.
> > 
> > If I understand correctly the code, the pm domain is already activated
> > at calling driver's probe callback.
> 
> As far as I can tell, the domain will also be powered off again after
> probe finished, unless the device grabs a runtime PM reference. This is
> what happens via the dev->pm_domain->sync() call after successful probe
> of a driver.

Ah, a good point.  This can be a problem with a probe work like this
case.

> It seems to me like it's not a very well defined case what to do when a
> device needs to be powered up but runtime PM is not enabled.
> 
> Adding Rafael and linux-pm, maybe they can provide some guidance on what
> to do in these situations.
> 
> To summarize, what we're debating here is how to handle powering up a
> device if the pm_runtime infrastructure doesn't take care of it. Jon's
> proposal here was, and we use this elsewhere, to do something like this:
> 
> 	pm_runtime_enable(dev);
> 	if (!pm_runtime_enabled(dev)) {
> 		err = foo_runtime_resume(dev);
> 		if (err < 0)
> 			goto fail;
> 	}
> 
> So basically when runtime PM is not available, we explicitly "resume"
> the device to power it up.
> 
> It seems to me like that's a fairly common problem, so I'm wondering if
> there's something that the runtime PM core could do to help with this.
> Or perhaps there's already a way to achieve this that we're all
> overlooking?
> 
> Rafael, any suggestions?

If any, a common helper would be appreciated, indeed.


thanks,

Takashi