[alsa-devel] [PATCH v2 040/186] ASoC: wm8961: replace codec to component
Kuninori Morimoto
kuninori.morimoto.gx at renesas.com
Mon Jan 29 04:09:02 CET 2018
From: Kuninori Morimoto <kuninori.morimoto.gx at renesas.com>
Now we can replace Codec to Component. Let's do it.
Note:
xxx_codec_xxx() -> xxx_component_xxx()
.idle_bias_off = 0 -> .idle_bias_on = 1
.ignore_pmdown_time = 0 -> .use_pmdown_time = 1
- -> .endianness = 1
- -> .non_legacy_dai_naming = 1
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx at renesas.com>
---
sound/soc/codecs/wm8961.c | 241 ++++++++++++++++++++++------------------------
1 file changed, 117 insertions(+), 124 deletions(-)
diff --git a/sound/soc/codecs/wm8961.c b/sound/soc/codecs/wm8961.c
index e23ceac..f70f563 100644
--- a/sound/soc/codecs/wm8961.c
+++ b/sound/soc/codecs/wm8961.c
@@ -194,89 +194,89 @@ static bool wm8961_readable(struct device *dev, unsigned int reg)
static int wm8961_hp_event(struct snd_soc_dapm_widget *w,
struct snd_kcontrol *kcontrol, int event)
{
- struct snd_soc_codec *codec = snd_soc_dapm_to_codec(w->dapm);
- u16 hp_reg = snd_soc_read(codec, WM8961_ANALOGUE_HP_0);
- u16 cp_reg = snd_soc_read(codec, WM8961_CHARGE_PUMP_1);
- u16 pwr_reg = snd_soc_read(codec, WM8961_PWR_MGMT_2);
- u16 dcs_reg = snd_soc_read(codec, WM8961_DC_SERVO_1);
+ struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
+ u16 hp_reg = snd_soc_component_read32(component, WM8961_ANALOGUE_HP_0);
+ u16 cp_reg = snd_soc_component_read32(component, WM8961_CHARGE_PUMP_1);
+ u16 pwr_reg = snd_soc_component_read32(component, WM8961_PWR_MGMT_2);
+ u16 dcs_reg = snd_soc_component_read32(component, WM8961_DC_SERVO_1);
int timeout = 500;
if (event & SND_SOC_DAPM_POST_PMU) {
/* Make sure the output is shorted */
hp_reg &= ~(WM8961_HPR_RMV_SHORT | WM8961_HPL_RMV_SHORT);
- snd_soc_write(codec, WM8961_ANALOGUE_HP_0, hp_reg);
+ snd_soc_component_write(component, WM8961_ANALOGUE_HP_0, hp_reg);
/* Enable the charge pump */
cp_reg |= WM8961_CP_ENA;
- snd_soc_write(codec, WM8961_CHARGE_PUMP_1, cp_reg);
+ snd_soc_component_write(component, WM8961_CHARGE_PUMP_1, cp_reg);
mdelay(5);
/* Enable the PGA */
pwr_reg |= WM8961_LOUT1_PGA | WM8961_ROUT1_PGA;
- snd_soc_write(codec, WM8961_PWR_MGMT_2, pwr_reg);
+ snd_soc_component_write(component, WM8961_PWR_MGMT_2, pwr_reg);
/* Enable the amplifier */
hp_reg |= WM8961_HPR_ENA | WM8961_HPL_ENA;
- snd_soc_write(codec, WM8961_ANALOGUE_HP_0, hp_reg);
+ snd_soc_component_write(component, WM8961_ANALOGUE_HP_0, hp_reg);
/* Second stage enable */
hp_reg |= WM8961_HPR_ENA_DLY | WM8961_HPL_ENA_DLY;
- snd_soc_write(codec, WM8961_ANALOGUE_HP_0, hp_reg);
+ snd_soc_component_write(component, WM8961_ANALOGUE_HP_0, hp_reg);
/* Enable the DC servo & trigger startup */
dcs_reg |=
WM8961_DCS_ENA_CHAN_HPR | WM8961_DCS_TRIG_STARTUP_HPR |
WM8961_DCS_ENA_CHAN_HPL | WM8961_DCS_TRIG_STARTUP_HPL;
- dev_dbg(codec->dev, "Enabling DC servo\n");
+ dev_dbg(component->dev, "Enabling DC servo\n");
- snd_soc_write(codec, WM8961_DC_SERVO_1, dcs_reg);
+ snd_soc_component_write(component, WM8961_DC_SERVO_1, dcs_reg);
do {
msleep(1);
- dcs_reg = snd_soc_read(codec, WM8961_DC_SERVO_1);
+ dcs_reg = snd_soc_component_read32(component, WM8961_DC_SERVO_1);
} while (--timeout &&
dcs_reg & (WM8961_DCS_TRIG_STARTUP_HPR |
WM8961_DCS_TRIG_STARTUP_HPL));
if (dcs_reg & (WM8961_DCS_TRIG_STARTUP_HPR |
WM8961_DCS_TRIG_STARTUP_HPL))
- dev_err(codec->dev, "DC servo timed out\n");
+ dev_err(component->dev, "DC servo timed out\n");
else
- dev_dbg(codec->dev, "DC servo startup complete\n");
+ dev_dbg(component->dev, "DC servo startup complete\n");
/* Enable the output stage */
hp_reg |= WM8961_HPR_ENA_OUTP | WM8961_HPL_ENA_OUTP;
- snd_soc_write(codec, WM8961_ANALOGUE_HP_0, hp_reg);
+ snd_soc_component_write(component, WM8961_ANALOGUE_HP_0, hp_reg);
/* Remove the short on the output stage */
hp_reg |= WM8961_HPR_RMV_SHORT | WM8961_HPL_RMV_SHORT;
- snd_soc_write(codec, WM8961_ANALOGUE_HP_0, hp_reg);
+ snd_soc_component_write(component, WM8961_ANALOGUE_HP_0, hp_reg);
}
if (event & SND_SOC_DAPM_PRE_PMD) {
/* Short the output */
hp_reg &= ~(WM8961_HPR_RMV_SHORT | WM8961_HPL_RMV_SHORT);
- snd_soc_write(codec, WM8961_ANALOGUE_HP_0, hp_reg);
+ snd_soc_component_write(component, WM8961_ANALOGUE_HP_0, hp_reg);
/* Disable the output stage */
hp_reg &= ~(WM8961_HPR_ENA_OUTP | WM8961_HPL_ENA_OUTP);
- snd_soc_write(codec, WM8961_ANALOGUE_HP_0, hp_reg);
+ snd_soc_component_write(component, WM8961_ANALOGUE_HP_0, hp_reg);
/* Disable DC offset cancellation */
dcs_reg &= ~(WM8961_DCS_ENA_CHAN_HPR |
WM8961_DCS_ENA_CHAN_HPL);
- snd_soc_write(codec, WM8961_DC_SERVO_1, dcs_reg);
+ snd_soc_component_write(component, WM8961_DC_SERVO_1, dcs_reg);
/* Finish up */
hp_reg &= ~(WM8961_HPR_ENA_DLY | WM8961_HPR_ENA |
WM8961_HPL_ENA_DLY | WM8961_HPL_ENA);
- snd_soc_write(codec, WM8961_ANALOGUE_HP_0, hp_reg);
+ snd_soc_component_write(component, WM8961_ANALOGUE_HP_0, hp_reg);
/* Disable the PGA */
pwr_reg &= ~(WM8961_LOUT1_PGA | WM8961_ROUT1_PGA);
- snd_soc_write(codec, WM8961_PWR_MGMT_2, pwr_reg);
+ snd_soc_component_write(component, WM8961_PWR_MGMT_2, pwr_reg);
/* Disable the charge pump */
- dev_dbg(codec->dev, "Disabling charge pump\n");
- snd_soc_write(codec, WM8961_CHARGE_PUMP_1,
+ dev_dbg(component->dev, "Disabling charge pump\n");
+ snd_soc_component_write(component, WM8961_CHARGE_PUMP_1,
cp_reg & ~WM8961_CP_ENA);
}
@@ -286,28 +286,28 @@ static int wm8961_hp_event(struct snd_soc_dapm_widget *w,
static int wm8961_spk_event(struct snd_soc_dapm_widget *w,
struct snd_kcontrol *kcontrol, int event)
{
- struct snd_soc_codec *codec = snd_soc_dapm_to_codec(w->dapm);
- u16 pwr_reg = snd_soc_read(codec, WM8961_PWR_MGMT_2);
- u16 spk_reg = snd_soc_read(codec, WM8961_CLASS_D_CONTROL_1);
+ struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
+ u16 pwr_reg = snd_soc_component_read32(component, WM8961_PWR_MGMT_2);
+ u16 spk_reg = snd_soc_component_read32(component, WM8961_CLASS_D_CONTROL_1);
if (event & SND_SOC_DAPM_POST_PMU) {
/* Enable the PGA */
pwr_reg |= WM8961_SPKL_PGA | WM8961_SPKR_PGA;
- snd_soc_write(codec, WM8961_PWR_MGMT_2, pwr_reg);
+ snd_soc_component_write(component, WM8961_PWR_MGMT_2, pwr_reg);
/* Enable the amplifier */
spk_reg |= WM8961_SPKL_ENA | WM8961_SPKR_ENA;
- snd_soc_write(codec, WM8961_CLASS_D_CONTROL_1, spk_reg);
+ snd_soc_component_write(component, WM8961_CLASS_D_CONTROL_1, spk_reg);
}
if (event & SND_SOC_DAPM_PRE_PMD) {
/* Disable the amplifier */
spk_reg &= ~(WM8961_SPKL_ENA | WM8961_SPKR_ENA);
- snd_soc_write(codec, WM8961_CLASS_D_CONTROL_1, spk_reg);
+ snd_soc_component_write(component, WM8961_CLASS_D_CONTROL_1, spk_reg);
/* Disable the PGA */
pwr_reg &= ~(WM8961_SPKL_PGA | WM8961_SPKR_PGA);
- snd_soc_write(codec, WM8961_PWR_MGMT_2, pwr_reg);
+ snd_soc_component_write(component, WM8961_PWR_MGMT_2, pwr_reg);
}
return 0;
@@ -505,15 +505,15 @@ static int wm8961_hw_params(struct snd_pcm_substream *substream,
struct snd_pcm_hw_params *params,
struct snd_soc_dai *dai)
{
- struct snd_soc_codec *codec = dai->codec;
- struct wm8961_priv *wm8961 = snd_soc_codec_get_drvdata(codec);
+ struct snd_soc_component *component = dai->component;
+ struct wm8961_priv *wm8961 = snd_soc_component_get_drvdata(component);
int i, best, target, fs;
u16 reg;
fs = params_rate(params);
if (!wm8961->sysclk) {
- dev_err(codec->dev, "MCLK has not been specified\n");
+ dev_err(component->dev, "MCLK has not been specified\n");
return -EINVAL;
}
@@ -524,23 +524,23 @@ static int wm8961_hw_params(struct snd_pcm_substream *substream,
abs(wm8961_srate[best].rate - fs))
best = i;
}
- reg = snd_soc_read(codec, WM8961_ADDITIONAL_CONTROL_3);
+ reg = snd_soc_component_read32(component, WM8961_ADDITIONAL_CONTROL_3);
reg &= ~WM8961_SAMPLE_RATE_MASK;
reg |= wm8961_srate[best].val;
- snd_soc_write(codec, WM8961_ADDITIONAL_CONTROL_3, reg);
- dev_dbg(codec->dev, "Selected SRATE %dHz for %dHz\n",
+ snd_soc_component_write(component, WM8961_ADDITIONAL_CONTROL_3, reg);
+ dev_dbg(component->dev, "Selected SRATE %dHz for %dHz\n",
wm8961_srate[best].rate, fs);
/* Select a CLK_SYS/fs ratio equal to or higher than required */
target = wm8961->sysclk / fs;
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && target < 64) {
- dev_err(codec->dev,
+ dev_err(component->dev,
"SYSCLK must be at least 64*fs for DAC\n");
return -EINVAL;
}
if (substream->stream == SNDRV_PCM_STREAM_CAPTURE && target < 256) {
- dev_err(codec->dev,
+ dev_err(component->dev,
"SYSCLK must be at least 256*fs for ADC\n");
return -EINVAL;
}
@@ -550,19 +550,19 @@ static int wm8961_hw_params(struct snd_pcm_substream *substream,
break;
}
if (i == ARRAY_SIZE(wm8961_clk_sys_ratio)) {
- dev_err(codec->dev, "Unable to generate CLK_SYS_RATE\n");
+ dev_err(component->dev, "Unable to generate CLK_SYS_RATE\n");
return -EINVAL;
}
- dev_dbg(codec->dev, "Selected CLK_SYS_RATE of %d for %d/%d=%d\n",
+ dev_dbg(component->dev, "Selected CLK_SYS_RATE of %d for %d/%d=%d\n",
wm8961_clk_sys_ratio[i].ratio, wm8961->sysclk, fs,
wm8961->sysclk / fs);
- reg = snd_soc_read(codec, WM8961_CLOCKING_4);
+ reg = snd_soc_component_read32(component, WM8961_CLOCKING_4);
reg &= ~WM8961_CLK_SYS_RATE_MASK;
reg |= wm8961_clk_sys_ratio[i].val << WM8961_CLK_SYS_RATE_SHIFT;
- snd_soc_write(codec, WM8961_CLOCKING_4, reg);
+ snd_soc_component_write(component, WM8961_CLOCKING_4, reg);
- reg = snd_soc_read(codec, WM8961_AUDIO_INTERFACE_0);
+ reg = snd_soc_component_read32(component, WM8961_AUDIO_INTERFACE_0);
reg &= ~WM8961_WL_MASK;
switch (params_width(params)) {
case 16:
@@ -579,15 +579,15 @@ static int wm8961_hw_params(struct snd_pcm_substream *substream,
default:
return -EINVAL;
}
- snd_soc_write(codec, WM8961_AUDIO_INTERFACE_0, reg);
+ snd_soc_component_write(component, WM8961_AUDIO_INTERFACE_0, reg);
/* Sloping stop-band filter is recommended for <= 24kHz */
- reg = snd_soc_read(codec, WM8961_ADC_DAC_CONTROL_2);
+ reg = snd_soc_component_read32(component, WM8961_ADC_DAC_CONTROL_2);
if (fs <= 24000)
reg |= WM8961_DACSLOPE;
else
reg &= ~WM8961_DACSLOPE;
- snd_soc_write(codec, WM8961_ADC_DAC_CONTROL_2, reg);
+ snd_soc_component_write(component, WM8961_ADC_DAC_CONTROL_2, reg);
return 0;
}
@@ -596,25 +596,25 @@ static int wm8961_set_sysclk(struct snd_soc_dai *dai, int clk_id,
unsigned int freq,
int dir)
{
- struct snd_soc_codec *codec = dai->codec;
- struct wm8961_priv *wm8961 = snd_soc_codec_get_drvdata(codec);
- u16 reg = snd_soc_read(codec, WM8961_CLOCKING1);
+ struct snd_soc_component *component = dai->component;
+ struct wm8961_priv *wm8961 = snd_soc_component_get_drvdata(component);
+ u16 reg = snd_soc_component_read32(component, WM8961_CLOCKING1);
if (freq > 33000000) {
- dev_err(codec->dev, "MCLK must be <33MHz\n");
+ dev_err(component->dev, "MCLK must be <33MHz\n");
return -EINVAL;
}
if (freq > 16500000) {
- dev_dbg(codec->dev, "Using MCLK/2 for %dHz MCLK\n", freq);
+ dev_dbg(component->dev, "Using MCLK/2 for %dHz MCLK\n", freq);
reg |= WM8961_MCLKDIV;
freq /= 2;
} else {
- dev_dbg(codec->dev, "Using MCLK/1 for %dHz MCLK\n", freq);
+ dev_dbg(component->dev, "Using MCLK/1 for %dHz MCLK\n", freq);
reg &= ~WM8961_MCLKDIV;
}
- snd_soc_write(codec, WM8961_CLOCKING1, reg);
+ snd_soc_component_write(component, WM8961_CLOCKING1, reg);
wm8961->sysclk = freq;
@@ -623,8 +623,8 @@ static int wm8961_set_sysclk(struct snd_soc_dai *dai, int clk_id,
static int wm8961_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
{
- struct snd_soc_codec *codec = dai->codec;
- u16 aif = snd_soc_read(codec, WM8961_AUDIO_INTERFACE_0);
+ struct snd_soc_component *component = dai->component;
+ u16 aif = snd_soc_component_read32(component, WM8961_AUDIO_INTERFACE_0);
aif &= ~(WM8961_BCLKINV | WM8961_LRP |
WM8961_MS | WM8961_FORMAT_MASK);
@@ -684,26 +684,26 @@ static int wm8961_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
return -EINVAL;
}
- return snd_soc_write(codec, WM8961_AUDIO_INTERFACE_0, aif);
+ return snd_soc_component_write(component, WM8961_AUDIO_INTERFACE_0, aif);
}
static int wm8961_set_tristate(struct snd_soc_dai *dai, int tristate)
{
- struct snd_soc_codec *codec = dai->codec;
- u16 reg = snd_soc_read(codec, WM8961_ADDITIONAL_CONTROL_2);
+ struct snd_soc_component *component = dai->component;
+ u16 reg = snd_soc_component_read32(component, WM8961_ADDITIONAL_CONTROL_2);
if (tristate)
reg |= WM8961_TRIS;
else
reg &= ~WM8961_TRIS;
- return snd_soc_write(codec, WM8961_ADDITIONAL_CONTROL_2, reg);
+ return snd_soc_component_write(component, WM8961_ADDITIONAL_CONTROL_2, reg);
}
static int wm8961_digital_mute(struct snd_soc_dai *dai, int mute)
{
- struct snd_soc_codec *codec = dai->codec;
- u16 reg = snd_soc_read(codec, WM8961_ADC_DAC_CONTROL_1);
+ struct snd_soc_component *component = dai->component;
+ u16 reg = snd_soc_component_read32(component, WM8961_ADC_DAC_CONTROL_1);
if (mute)
reg |= WM8961_DACMU;
@@ -712,27 +712,27 @@ static int wm8961_digital_mute(struct snd_soc_dai *dai, int mute)
msleep(17);
- return snd_soc_write(codec, WM8961_ADC_DAC_CONTROL_1, reg);
+ return snd_soc_component_write(component, WM8961_ADC_DAC_CONTROL_1, reg);
}
static int wm8961_set_clkdiv(struct snd_soc_dai *dai, int div_id, int div)
{
- struct snd_soc_codec *codec = dai->codec;
+ struct snd_soc_component *component = dai->component;
u16 reg;
switch (div_id) {
case WM8961_BCLK:
- reg = snd_soc_read(codec, WM8961_CLOCKING2);
+ reg = snd_soc_component_read32(component, WM8961_CLOCKING2);
reg &= ~WM8961_BCLKDIV_MASK;
reg |= div;
- snd_soc_write(codec, WM8961_CLOCKING2, reg);
+ snd_soc_component_write(component, WM8961_CLOCKING2, reg);
break;
case WM8961_LRCLK:
- reg = snd_soc_read(codec, WM8961_AUDIO_INTERFACE_2);
+ reg = snd_soc_component_read32(component, WM8961_AUDIO_INTERFACE_2);
reg &= ~WM8961_LRCLK_RATE_MASK;
reg |= div;
- snd_soc_write(codec, WM8961_AUDIO_INTERFACE_2, reg);
+ snd_soc_component_write(component, WM8961_AUDIO_INTERFACE_2, reg);
break;
default:
@@ -742,7 +742,7 @@ static int wm8961_set_clkdiv(struct snd_soc_dai *dai, int div_id, int div)
return 0;
}
-static int wm8961_set_bias_level(struct snd_soc_codec *codec,
+static int wm8961_set_bias_level(struct snd_soc_component *component,
enum snd_soc_bias_level level)
{
u16 reg;
@@ -757,36 +757,36 @@ static int wm8961_set_bias_level(struct snd_soc_codec *codec,
break;
case SND_SOC_BIAS_PREPARE:
- if (snd_soc_codec_get_bias_level(codec) == SND_SOC_BIAS_STANDBY) {
+ if (snd_soc_component_get_bias_level(component) == SND_SOC_BIAS_STANDBY) {
/* Enable bias generation */
- reg = snd_soc_read(codec, WM8961_ANTI_POP);
+ reg = snd_soc_component_read32(component, WM8961_ANTI_POP);
reg |= WM8961_BUFIOEN | WM8961_BUFDCOPEN;
- snd_soc_write(codec, WM8961_ANTI_POP, reg);
+ snd_soc_component_write(component, WM8961_ANTI_POP, reg);
/* VMID=2*50k, VREF */
- reg = snd_soc_read(codec, WM8961_PWR_MGMT_1);
+ reg = snd_soc_component_read32(component, WM8961_PWR_MGMT_1);
reg &= ~WM8961_VMIDSEL_MASK;
reg |= (1 << WM8961_VMIDSEL_SHIFT) | WM8961_VREF;
- snd_soc_write(codec, WM8961_PWR_MGMT_1, reg);
+ snd_soc_component_write(component, WM8961_PWR_MGMT_1, reg);
}
break;
case SND_SOC_BIAS_STANDBY:
- if (snd_soc_codec_get_bias_level(codec) == SND_SOC_BIAS_PREPARE) {
+ if (snd_soc_component_get_bias_level(component) == SND_SOC_BIAS_PREPARE) {
/* VREF off */
- reg = snd_soc_read(codec, WM8961_PWR_MGMT_1);
+ reg = snd_soc_component_read32(component, WM8961_PWR_MGMT_1);
reg &= ~WM8961_VREF;
- snd_soc_write(codec, WM8961_PWR_MGMT_1, reg);
+ snd_soc_component_write(component, WM8961_PWR_MGMT_1, reg);
/* Bias generation off */
- reg = snd_soc_read(codec, WM8961_ANTI_POP);
+ reg = snd_soc_component_read32(component, WM8961_ANTI_POP);
reg &= ~(WM8961_BUFIOEN | WM8961_BUFDCOPEN);
- snd_soc_write(codec, WM8961_ANTI_POP, reg);
+ snd_soc_component_write(component, WM8961_ANTI_POP, reg);
/* VMID off */
- reg = snd_soc_read(codec, WM8961_PWR_MGMT_1);
+ reg = snd_soc_component_read32(component, WM8961_PWR_MGMT_1);
reg &= ~WM8961_VMIDSEL_MASK;
- snd_soc_write(codec, WM8961_PWR_MGMT_1, reg);
+ snd_soc_component_write(component, WM8961_PWR_MGMT_1, reg);
}
break;
@@ -830,51 +830,51 @@ static int wm8961_set_bias_level(struct snd_soc_codec *codec,
.ops = &wm8961_dai_ops,
};
-static int wm8961_probe(struct snd_soc_codec *codec)
+static int wm8961_probe(struct snd_soc_component *component)
{
u16 reg;
/* Enable class W */
- reg = snd_soc_read(codec, WM8961_CHARGE_PUMP_B);
+ reg = snd_soc_component_read32(component, WM8961_CHARGE_PUMP_B);
reg |= WM8961_CP_DYN_PWR_MASK;
- snd_soc_write(codec, WM8961_CHARGE_PUMP_B, reg);
+ snd_soc_component_write(component, WM8961_CHARGE_PUMP_B, reg);
/* Latch volume update bits (right channel only, we always
* write both out) and default ZC on. */
- reg = snd_soc_read(codec, WM8961_ROUT1_VOLUME);
- snd_soc_write(codec, WM8961_ROUT1_VOLUME,
+ reg = snd_soc_component_read32(component, WM8961_ROUT1_VOLUME);
+ snd_soc_component_write(component, WM8961_ROUT1_VOLUME,
reg | WM8961_LO1ZC | WM8961_OUT1VU);
- snd_soc_write(codec, WM8961_LOUT1_VOLUME, reg | WM8961_LO1ZC);
- reg = snd_soc_read(codec, WM8961_ROUT2_VOLUME);
- snd_soc_write(codec, WM8961_ROUT2_VOLUME,
+ snd_soc_component_write(component, WM8961_LOUT1_VOLUME, reg | WM8961_LO1ZC);
+ reg = snd_soc_component_read32(component, WM8961_ROUT2_VOLUME);
+ snd_soc_component_write(component, WM8961_ROUT2_VOLUME,
reg | WM8961_SPKRZC | WM8961_SPKVU);
- snd_soc_write(codec, WM8961_LOUT2_VOLUME, reg | WM8961_SPKLZC);
+ snd_soc_component_write(component, WM8961_LOUT2_VOLUME, reg | WM8961_SPKLZC);
- reg = snd_soc_read(codec, WM8961_RIGHT_ADC_VOLUME);
- snd_soc_write(codec, WM8961_RIGHT_ADC_VOLUME, reg | WM8961_ADCVU);
- reg = snd_soc_read(codec, WM8961_RIGHT_INPUT_VOLUME);
- snd_soc_write(codec, WM8961_RIGHT_INPUT_VOLUME, reg | WM8961_IPVU);
+ reg = snd_soc_component_read32(component, WM8961_RIGHT_ADC_VOLUME);
+ snd_soc_component_write(component, WM8961_RIGHT_ADC_VOLUME, reg | WM8961_ADCVU);
+ reg = snd_soc_component_read32(component, WM8961_RIGHT_INPUT_VOLUME);
+ snd_soc_component_write(component, WM8961_RIGHT_INPUT_VOLUME, reg | WM8961_IPVU);
/* Use soft mute by default */
- reg = snd_soc_read(codec, WM8961_ADC_DAC_CONTROL_2);
+ reg = snd_soc_component_read32(component, WM8961_ADC_DAC_CONTROL_2);
reg |= WM8961_DACSMM;
- snd_soc_write(codec, WM8961_ADC_DAC_CONTROL_2, reg);
+ snd_soc_component_write(component, WM8961_ADC_DAC_CONTROL_2, reg);
/* Use automatic clocking mode by default; for now this is all
* we support.
*/
- reg = snd_soc_read(codec, WM8961_CLOCKING_3);
+ reg = snd_soc_component_read32(component, WM8961_CLOCKING_3);
reg &= ~WM8961_MANUAL_MODE;
- snd_soc_write(codec, WM8961_CLOCKING_3, reg);
+ snd_soc_component_write(component, WM8961_CLOCKING_3, reg);
return 0;
}
#ifdef CONFIG_PM
-static int wm8961_resume(struct snd_soc_codec *codec)
+static int wm8961_resume(struct snd_soc_component *component)
{
- snd_soc_cache_sync(codec);
+ snd_soc_component_cache_sync(component);
return 0;
}
@@ -882,20 +882,21 @@ static int wm8961_resume(struct snd_soc_codec *codec)
#define wm8961_resume NULL
#endif
-static const struct snd_soc_codec_driver soc_codec_dev_wm8961 = {
- .probe = wm8961_probe,
- .resume = wm8961_resume,
- .set_bias_level = wm8961_set_bias_level,
- .suspend_bias_off = true,
-
- .component_driver = {
- .controls = wm8961_snd_controls,
- .num_controls = ARRAY_SIZE(wm8961_snd_controls),
- .dapm_widgets = wm8961_dapm_widgets,
- .num_dapm_widgets = ARRAY_SIZE(wm8961_dapm_widgets),
- .dapm_routes = audio_paths,
- .num_dapm_routes = ARRAY_SIZE(audio_paths),
- },
+static const struct snd_soc_component_driver soc_component_dev_wm8961 = {
+ .probe = wm8961_probe,
+ .resume = wm8961_resume,
+ .set_bias_level = wm8961_set_bias_level,
+ .controls = wm8961_snd_controls,
+ .num_controls = ARRAY_SIZE(wm8961_snd_controls),
+ .dapm_widgets = wm8961_dapm_widgets,
+ .num_dapm_widgets = ARRAY_SIZE(wm8961_dapm_widgets),
+ .dapm_routes = audio_paths,
+ .num_dapm_routes = ARRAY_SIZE(audio_paths),
+ .suspend_bias_off = 1,
+ .idle_bias_on = 1,
+ .use_pmdown_time = 1,
+ .endianness = 1,
+ .non_legacy_dai_naming = 1,
};
static const struct regmap_config wm8961_regmap = {
@@ -961,19 +962,12 @@ static int wm8961_i2c_probe(struct i2c_client *i2c,
i2c_set_clientdata(i2c, wm8961);
- ret = snd_soc_register_codec(&i2c->dev,
- &soc_codec_dev_wm8961, &wm8961_dai, 1);
+ ret = devm_snd_soc_register_component(&i2c->dev,
+ &soc_component_dev_wm8961, &wm8961_dai, 1);
return ret;
}
-static int wm8961_i2c_remove(struct i2c_client *client)
-{
- snd_soc_unregister_codec(&client->dev);
-
- return 0;
-}
-
static const struct i2c_device_id wm8961_i2c_id[] = {
{ "wm8961", 0 },
{ }
@@ -985,7 +979,6 @@ static int wm8961_i2c_remove(struct i2c_client *client)
.name = "wm8961",
},
.probe = wm8961_i2c_probe,
- .remove = wm8961_i2c_remove,
.id_table = wm8961_i2c_id,
};
--
1.9.1
More information about the Alsa-devel
mailing list