[alsa-devel] [PATCH 6/9] ARM: dts: sun8i: restore the inclusion of ccu headers in V3s DTSI

[Icenowy Zheng]

When the V3s support patchset is applied, CCU headers and V3s DTSI went
into different trees, so the CCU inclusion is removed in the DTSI.

Add back them.

Signed-off-by: Icenowy Zheng <icenowy at aosc.xyz>
---
 arch/arm/boot/dts/sun8i-v3s.dtsi | 67 ++++++++++++++++++++--------------------
 1 file changed, 34 insertions(+), 33 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
index 71075969e5e6..b3f8b7f9c0bb 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
@@ -40,6 +40,8 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
+#include <dt-bindings/clock/sun8i-v3s-ccu.h>
+#include <dt-bindings/reset/sun8i-v3s-ccu.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
@@ -55,7 +57,7 @@
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <0>;
-			clocks = <&ccu 14>;
+			clocks = <&ccu CLK_CPU>;
 		};
 	};
 
@@ -96,15 +98,15 @@
 		mmc0: mmc at 01c0f000 {
 			compatible = "allwinner,sun7i-a20-mmc";
 			reg = <0x01c0f000 0x1000>;
-			clocks = <&ccu 22>,
-				 <&ccu 45>,
-				 <&ccu 47>,
-				 <&ccu 46>;
+			clocks = <&ccu CLK_BUS_MMC0>,
+				 <&ccu CLK_MMC0>,
+				 <&ccu CLK_MMC0_OUTPUT>,
+				 <&ccu CLK_MMC0_SAMPLE>;
 			clock-names = "ahb",
 				      "mmc",
 				      "output",
 				      "sample";
-			resets = <&ccu 7>;
+			resets = <&ccu RST_BUS_MMC0>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -115,15 +117,15 @@
 		mmc1: mmc at 01c10000 {
 			compatible = "allwinner,sun7i-a20-mmc";
 			reg = <0x01c10000 0x1000>;
-			clocks = <&ccu 23>,
-				 <&ccu 48>,
-				 <&ccu 50>,
-				 <&ccu 49>;
+			clocks = <&ccu CLK_BUS_MMC1>,
+				 <&ccu CLK_MMC1>,
+				 <&ccu CLK_MMC1_OUTPUT>,
+				 <&ccu CLK_MMC1_SAMPLE>;
 			clock-names = "ahb",
 				      "mmc",
 				      "output",
 				      "sample";
-			resets = <&ccu 8>;
+			resets = <&ccu RST_BUS_MMC1>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -134,15 +136,15 @@
 		mmc2: mmc at 01c11000 {
 			compatible = "allwinner,sun7i-a20-mmc";
 			reg = <0x01c11000 0x1000>;
-			clocks = <&ccu 24>,
-				 <&ccu 51>,
-				 <&ccu 53>,
-				 <&ccu 52>;
+			clocks = <&ccu CLK_BUS_MMC2>,
+				 <&ccu CLK_MMC2>,
+				 <&ccu CLK_MMC2_OUTPUT>,
+				 <&ccu CLK_MMC2_SAMPLE>;
 			clock-names = "ahb",
 				      "mmc",
 				      "output",
 				      "sample";
-			resets = <&ccu 9>;
+			resets = <&ccu RST_BUS_MMC2>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -153,8 +155,8 @@
 		usb_otg: usb at 01c19000 {
 			compatible = "allwinner,sun8i-h3-musb";
 			reg = <0x01c19000 0x0400>;
-			clocks = <&ccu 29>;
-			resets = <&ccu 17>;
+			clocks = <&ccu CLK_BUS_OTG>;
+			resets = <&ccu RST_BUS_OTG>;
 			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "mc";
 			phys = <&usbphy 0>;
@@ -169,9 +171,9 @@
 			      <0x01c1a800 0x4>;
 			reg-names = "phy_ctrl",
 				    "pmu0";
-			clocks = <&ccu 56>;
+			clocks = <&ccu CLK_USB_PHY0>;
 			clock-names = "usb0_phy";
-			resets = <&ccu 0>;
+			resets = <&ccu RST_USB_PHY0>;
 			reset-names = "usb0_reset";
 			status = "disabled";
 			#phy-cells = <1>;
@@ -198,7 +200,7 @@
 			reg = <0x01c20800 0x400>;
 			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu 37>, <&osc24M>, <&osc32k>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
@@ -213,6 +215,7 @@
 			uart0_pins_a: uart0 at 0 {
 				pins = "PB8", "PB9";
 				function = "uart0";
+				bias-pull-up;
 			};
 
 			mmc0_pins_a: mmc0 at 0 {
@@ -244,8 +247,8 @@
 			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&ccu 40>;
-			resets = <&ccu 49>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
 			status = "disabled";
 		};
 
@@ -255,8 +258,8 @@
 			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&ccu 41>;
-			resets = <&ccu 50>;
+			clocks = <&ccu CLK_BUS_UART1>;
+			resets = <&ccu RST_BUS_UART1>;
 			status = "disabled";
 		};
 
@@ -266,8 +269,8 @@
 			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&ccu 42>;
-			resets = <&ccu 51>;
+			clocks = <&ccu CLK_BUS_UART2>;
+			resets = <&ccu RST_BUS_UART2>;
 			status = "disabled";
 		};
 
@@ -275,10 +278,8 @@
 			compatible = "allwinner,sun6i-a31-i2c";
 			reg = <0x01c2ac00 0x400>;
 			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu 38>;
-			resets = <&ccu 46>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c0_pins>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -288,8 +289,8 @@
 			compatible = "allwinner,sun6i-a31-i2c";
 			reg = <0x01c2b000 0x400>;
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu 39>;
-			resets = <&ccu 47>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
-- 
2.11.1