[alsa-devel] [PATCH v3 3/5] ASoC: codecs: msm8916-wcd-analog: add MBHC support

[Damien Riegel]

Hi,


On Thu, Aug 10, 2017 at 09:33:29AM -0400, Damien Riegel wrote:
> Hi,
> 
> On Thu, Aug 10, 2017 at 11:02:34AM +0100, Srinivas Kandagatla wrote:
> > Hi Damien,
> > Thanks for testing.
> > 
> > On 09/08/17 22:10, Damien Riegel wrote:
> > > Hi Srinivas,
> > > 
> > > On Wed, Aug 09, 2017 at 06:49:25PM +0200, srinivas.kandagatla at linaro.org wrote:
> > > > From: Srinivas Kandagatla <srinivas.kandagatla at linaro.org>
> > > > 
> > > > MBHC (MultiButton Headset Control) support is available in pm8921 in two
> > > > blocks, one to detect mechanical headset insertion and removal and other
> > > > block to support headset type detection and 5 button detection and othe
> > > > features like impedance calculation.
> > > > 
> > > > This patch adds support to:
> > > > 1> Support to NC and NO type of headset Jacks.
> > > > 2> Mechanical insertion and detection of headset jack.
> > > > 3> Detect a 3 pole Headphone and a 4 pole Headset.
> > > > 4> Detect 5 buttons.
> > > > 
> > > > Tested it on DB410c with Audio Mezz board with 4 pole and 3 pole
> > > > headset/headphones.
> > > 
> > > I have the same issue with this patchset, KEY_MEDIA is being reported
> > > when unplugging a headset. I added a few traces and what I observe is
> > Am unable to reproduce the same issue, I tried atleast 6 different mix of
> > headset/headphones.
> > here is my evtest log:  http://paste.ubuntu.com/25282592/
> > 
> > Could you explain bit more about your setup, so that I can try to reproduce
> > the same issue.
> > 
> > My setup is DB410c + Audio Mezz board
> > https://www.arrow.com/en/products/audiomezz/seeed-technology-limited
> 
> I'm using a hardware based on Intrinsyc Open-Q 410 Development Kit:
> https://www.intrinsyc.com/snapdragon-embedded-development-kits/snapdragon-410-development-kit/
> 
> We use the same SoM with a different carrier board, but connections to
> the jack connector are routed the same way on both carrier boards.
> 
> > > that the "button pressed" irq is fired when unplugging, but no "button
> > > released" irq follows. To get a "button released" irq, I need to either
> > > plug a headset, or plug-and-unplug headphones.
> > > 
> > > So basically, detection fails because we don't get the "button pressed"
> > > irq prior to the mechanical switch irq. Do you know what could explain
> > > the MBHC not firing the "button released" irq when unplugging headset?
> > > 
> > Can you also share output of evetest and /proc/interrupts so that i can see
> > if the extra logic of masking btn0 is creating the issue, we can also try
> > removing the btn0 accessory detect logic and see if we get correct button
> > press/releases.
> 
> It's definitely what's causing the headphones to be reported as headset,
> but not what's causing the interrupt not to be triggered in the first
> place. I don't have access to the hardware right now, so I'll provide
> you with logs next week.

I did the test, and addded the content of /proc/interrupts.

    https://paste.ubuntu.com/25312443/

As you can see, after "[INSERT HEADPHONE]", we only get "mbhc switch
irq", but not "mbhc btn press irq". Let me know if you need more
details.

As I said before, I don't see that 100% of the time, but I don't do
anything special to trigger it either (like pulling the cable extra
slowly or whatnot), it just happens.


Thank you,
-- 
Damien