[alsa-devel] Wolfson 5102 on Beaglebone Black using ALSA
Charles Keepax
ckeepax at opensource.wolfsonmicro.com
Mon May 30 19:19:28 CEST 2016
On Mon, May 30, 2016 at 08:18:17AM -0700, Clark Dunson wrote:
> > There are some hoops to jump through to get access to the
> > necessary compilers etc. for the DSP, although again Joao who I
> > CCed on your other email would be a good place to start the
> > process of getting access to that.
>
> Thank you, this part may come later this year.
>
> > Yeah please avoid doing this, the driver should support all the
> > features you require from the sound of things. There should be no
> > need to hard code register writes.
> >
> > What sort of things are you setting up with these register
> > writes? Lets see if I can point you in the direction of the
> > correct place to put some of those.
>
> Thanks!
>
> The clocking:
>
> regmap_write(arizona->regmap, ARIZONA_CLOCK_32K_1, 0x00042); // Use Sysclk, Default = 0x0041
Ah that one, yeah that is a problem. Generally very few of our
customers use the system without a 32k clock on MCLK2. There is
indeed no way to specify this right now other than this hack. I
am working on a series of clocking patches which you refer to the
binding doc on below but those are going to take a while to get
merged. The issue is that the clocking framework really doesn't
play nice with the SPI framework at this point in time and that
needs to get sorted before I can merge them. Are you looking to
upstream support for this board as you develope it? We might have
to have a think about how we are going to support this one.
> regmap_write(arizona->regmap, ARIZONA_SYSTEM_CLOCK_1, 0x0200); // Use MCLK1, and 24.576MHz from BBB McASP, Default = 0x0304
For this one you just need to add this call to your machine
driver (late probe is usually a good place):
snd_soc_codec_set_sysclk(codec, ARIZONA_CLK_SYSCLK,
ARIZONA_CLK_SRC_MCLK1, 24576000,
SND_SOC_CLOCK_IN);
Although appreciate that is a little harder if you are using
simple card.
>
> These would seem to be the relevant device tree entries from Documentation/devicetree/bindings/mfd/arizona.txt:
>
> - clocks: Should reference the clocks supplied on MCLK1 and MCLK2
> - clock-names: Should contains two strings:
> "mclk1" for the clock supplied on MCLK1, recommended to be a high
> quality audio reference clock
> "mclk2" for the clock supplied on MCLK2, recommended to be an always on
> 32k clock
>
> Still trying to figure out how to specify these. I have pasted our device tree to the end of this email. (Oh, gpio for BBB McASP clock is deliberately routed away from gpio1_27, because somehow we are not convincing the driver to enable it, and so we have a gpio_set_value(MY_CLOCK_GPIO_ENABLE,1); in arizona-core probe until we figure out how.
Didn't actually think these where merged yet, ok well. The
binding is good but the driver has no support for it yet.
>
> >> We had to simply disinvite extcon-arizona from the party
> >> though. On both the WM5102-6271-CS137-M-SCH-REV2.03 and our
> >> protoboard, JACKDET is an IRQ gone wild. On the Wolfson board,
> >> inserting my headphones into the jack shut it up. But on our
> >> protoboard, where we left that pin unconnected, we found that
> >> the probe of extcon-arizona hard enables JACKDET.
> >>
> > I am surprised you are seeing issues on one of our boards, they
> > are all fairly well tested here. I would quite like to see a
> > kernel log on that one if I can?
>
> Okay, I’ll hook up the dev board, likely Thurs-Fri after we complete
> board bring up.
>
> > Apart from that, this all seems reasonable, the extcon driver
> > exists to control the jack detection. If that is not wired up on
> > your system then not building in this part of the system seems
> > the correct response.
> >
> > Thanks,
> > Charles
>
> Thank you, Clark.
>
> Device Tree _______________________________________
>
> /*
> * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
> *
> * This program is free software; you can redistribute it and/or modify
> * it under the terms of the GNU General Public License version 2 as
> * published by the Free Software Foundation.
> */
> /dts-v1/;
>
> #include "am33xx.dtsi"
> #include "am335x-bone-common.dtsi"
> #include "dt-bindings/mfd/arizona.h"
>
> / {
> model = "TI AM335x BeagleBone Black";
> compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
>
>
> leds {
> pinctrl-names = "default";
> pinctrl-0 = <&led_pins_default>;
> compatible = "gpio-leds";
>
> led at 1 {
> label= "led_ir";
> gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
> default-state = "off";
> };
>
> led at 2 {
> label= "led_red";
> gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
> default-state = "off";
> };
> };
>
>
>
> ldo18: ldo18 {
> compatible = "regulator-fixed";
> regulator-name = "DC_1V8";
> regulator-min-microvolt = <1800000>;
> regulator-max-microvolt = <1800000>;
> enable-active-high;
> regulator-always-on;
> };
>
> ldo50: ldo50 { /* BBB VCC_5V */
> compatible = "regulator-fixed";
> regulator-name = "DC_5V0";
> regulator-min-microvolt = <5000000>;
> regulator-max-microvolt = <5000000>;
> enable-active-high;
> regulator-always-on;
> };
>
> clk_audio_fixed: clk_audio_fixed {
> #clock-cells = <0>;
> compatible = "fixed-clock";
> clock-frequency = <24576000>;
> };
>
>
> clk_audio: clk_audio {
> #clock-cells = <0>;
> compatible = "gpio-gate-clock";
> clocks = <&clk_audio_fixed>;
> enable-gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>; /* BeagleBone Black Clk enable on GPIO1_27 */
> };
>
>
> sound: sound at 0 {
> status = "okay";
> compatible = "simple-audio-card";
> simple-audio-card,name = "WM5102";
> simple-audio-card,widgets =
> "Line", "Line In";
> simple-audio-card,routing =
> "IN1L", "Line In",
> "IN1R", "Line In",
> "IN2L", "Line In",
> "IN2R", "Line In",
> "IN3L", "Line In",
> "IN3R", "Line In";
> /* simple-audio-card,hp-det-gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>; /*TP38*/
> /*simple-audio-card,dai-link {*/
> simple-audio-card,format = "dsp_b";
> simple-audio-card,bitclock-master = <&sound_master>;
> simple-audio-card,frame-master = <&sound_master>;
> simple-audio-card,cpu {
> sound-dai = <&mcasp0>;
> clocks = <&clk_audio>;
> /*
> dai-tdm-slot-num = <6>;
> dai-tdm-slot-width = <32>;
> */
> };
> sound_master: simple-audio-card,codec {
> sound-dai = <&wm5102>;
> clocks = <&clk_audio>;
> system-clock-id = <1>; /* ARIZONA_CLK_SYSCLK */
> /*
> dai-tdm-slot-num = <6>;
> dai-tdm-slot-width = <32>;
> */
> };
> /* };*/
>
> };
>
> };
>
> &ldo3_reg {
> regulator-min-microvolt = <1800000>;
> regulator-max-microvolt = <1800000>;
> regulator-always-on;
> };
>
> &mmc1 {
> vmmc-supply = <&vmmcsd_fixed>;
> };
>
> &mmc2 {
> vmmc-supply = <&vmmcsd_fixed>;
> pinctrl-names = "default";
> pinctrl-0 = <&emmc_pins>;
> bus-width = <8>;
> status = "okay";
> };
>
> &am33xx_pinmux {
>
> nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
> pinctrl-single,pins = <
> 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
> 0x18c ( PIN_INPUT_PULLUP | MUX_MODE0 ) /* (C16) I2C0_SCL.I2C0_SCL */
> 0x188 ( PIN_INPUT_PULLUP | MUX_MODE0 ) /* (C17) I2C0_SDA.I2C0_SDA */
> >;
> };
>
> nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
> pinctrl-single,pins = <
> 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
> 0x18c ( PIN_INPUT | MUX_MODE0 ) /* (C16) I2C0_SCL.I2C0_SCL */
> 0x188 ( PIN_INPUT | MUX_MODE0 ) /* (C17) I2C0_SDA.I2C0_SDA */
> >;
> };
>
> led_pins_default: led_pins_default {
> pinctrl-single,pins = <
> 0x178 ( PIN_OUTPUT | MUX_MODE7 ) /* (D18) uart1_ctsn.gpio0[12] TP38 */
> 0x17c ( PIN_OUTPUT | MUX_MODE7 ) /* (D17) uart1_rtsn.gpio0[13] TP39 */
> 0x28 ( PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) /* (T11) gpmc_ad10.gpio0[26] IR LED */
> 0x38 ( PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) /* (V13) gpmc_ad14.gpio1[14] RED LED */
> >;
> };
>
> accel_pins_default: accel_pins_default {
> pinctrl-single,pins = <
> 0xe8 ( PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) /* (V5) lcd_pclk.gpio2[24] ACCEL_ST */
> 0xec ( PIN_OUTPUT_PULLUP | MUX_MODE7 ) /* (R6) lcd_ac_bias_en.gpio2[25] ACCEL_FS */
> >;
> };
>
> mcasp0_slave_pins_default: mcasp0_slave_pins_default {
> pinctrl-single,pins = <
> 0x1a0 ( PIN_INPUT | MUX_MODE0 ) /* (B12) mcasp0_aclkr.mcasp0_aclkr */
> 0x1a4 ( PIN_INPUT | MUX_MODE0 ) /* (C13) mcasp0_fsr.mcasp0_fsr */
> 0x198 ( PIN_INPUT | MUX_MODE0 ) /* (D12) mcasp0_axr0.mcasp0_axr0 */
> 0x19c ( PIN_OUTPUT | MUX_MODE2 ) /* (C12) mcasp0_ahclkr.mcasp0_axr2 */
> >;
> };
>
> wm5102_pins_default: wm5102_pins_default {
> pinctrl-single,pins = <
> 0x6c ( PIN_OUTPUT_PULLUP | MUX_MODE7 ) /* (V17) gpmc_a11.gpio1[27] 24.576 MHZ CE */
> 0x78 ( PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) /* (U18) gpmc_be1n.gpio1[28] /RESET */
> 0x7c ( PIN_OUTPUT_PULLUP | MUX_MODE7 ) /* (V6) gpmc_csn0.gpio1[29] LDOENA */
> 0xe4 ( PIN_INPUT | MUX_MODE7 ) /* (R5) lcd_hsync.gpio2[23] /IRQ */
> 0x1ac ( PIN_INPUT_PULLUP | MUX_MODE0 ) /* (A14) mcasp0_ahclkx.gpio3[21] AUDIO_MCLK */
> 0x15c ( PIN_INPUT_PULLUP | MUX_MODE2 ) /* (A16) spi0_cs0.I2C1_SCL */
> 0x158 ( PIN_INPUT_PULLUP | MUX_MODE2 ) /* (B16) spi0_d1.I2C1_SDA */
> 0x164 ( PIN_INPUT | MUX_MODE7 ) /* (C18) eCAP0_in_PWM0_out.gpio0[7] (AUDIO BCLK) HIGHZ*/
> >;
> };
>
>
> };
>
> &lcdc {
> status = "disabled";
> port {
> lcdc_0: endpoint at 0 {
> remote-endpoint = <&hdmi_0>;
> };
> };
> };
>
> &i2c0 {
> tda19988 {
> compatible = "nxp,tda998x";
> reg = <0x70>;
> pinctrl-names = "default", "off";
> pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
> pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
>
> port {
> hdmi_0: endpoint at 0 {
> remote-endpoint = <&lcdc_0>;
> };
> };
> };
> };
>
>
> &i2c1 {
> pinctrl-names = "default";
> pintctrl-0 = <&wm5102_pins_default>;
> status = "okay";
> clock-frequency = <400000>;
>
>
> wm5102: wm5102 at 1b {
> compatible = "wlf,wm5102";
> reg = <0x1b>;
> status = "okay";
> /* /IRQ is connected to GPIO2_23. Mask from HiassofT DT for cirrus audio board was 8 */
> interrupts = <23 8>;
> interrupt-controller;
> #interrupt-cells = <2>;
> interrupt-parent = <&gpio2>;
> /*clock-names = "mclk1", "mclk2";*/
> gpio-controller;
> #gpio-cells = <2>;
> wlf,gpio-defaults = <
> ARIZONA_GP_FN_TXLRCLK
> ARIZONA_GP_DEFAULT
> ARIZONA_GP_DEFAULT
> ARIZONA_GP_DEFAULT
> ARIZONA_GP_DEFAULT
> >;
> wlf,reset = <&gpio1 28 GPIO_ACTIVE_HIGH>; /* allow /RESET wm5102 by driver (via inverter)*/
> wlf,ldoena = <&gpio1 29 GPIO_ACTIVE_HIGH>; /* allow LDOENA wm5102 by driver */
This here is the correct place for the ldoena.
> LDOVDD-supply = <&ldo18>; /* fixed 1V8 regulator */
> AVDD-supply = <&ldo18>;
> DBVDD1-supply = <&ldo18>;
> DBVDD2-supply = <&ldo18>;
> DBVDD3-supply = <&ldo18>;
> CPVDD-supply = <&ldo18>;
> /*DCVDD-supply = <&ldo18>; /* supplied by LDO1
Yeah this line can go you don't need to specify DCVDD unless you
are not using the internal LDO.
> MICVDD-supply = <&ldo50>;
> SPKVDDL-supply = <&ldo50>; /* fixed VDD_5V from BBB */
> SPKVDDR-supply = <&ldo50>;
> #sound-dai-cells = <0>;
> /* we haven't figured out how reference the internal LDO, pin is pulled up */
> #if 0
> ldo1: ldo1 {
> wlf,ldoena = <&gpio1 29 GPIO_ACTIVE_HIGH>; /* allow LDOENA wm5102 by driver */
> };
> #endif
This can go as well again no need to specify a block for internal
LDO unless you want to do some strange configuration of it which
you almost certainly don't.
> };
>
> };
>
>
> &mcasp0 {
> pinctrl-names = "default";
> pinctrl-0 = <&mcasp0_slave_pins_default>;
>
> status = "okay";
> op-mode = <0>; /* MCASP_IIS_MODE */
> tdm-slots = <6>;
> /* 4 serializers */
> serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX - 0 2 0 0 */
> 2 0 0 0
> >;
> tx-num-evt = <32>;
> rx-num-evt = <32>;
> #sound-dai-cells = <0>;
> };
>
>
> &rtc {
> system-power-controller;
> };
>
>
>
More information about the Alsa-devel
mailing list