[alsa-devel] Imx6 i2s master driver without i2c
Caleb Crome
caleb at crome.org
Tue May 10 18:14:40 CEST 2016
Hi Nicola,
Answers inline. BTW, it's highly preferred on this list that you
don't 'top-post', which I had to look up when I was told not to do it
:-). Basically, put replies below the stuff they refer to, not above,
so somebody coming into the middle of the conversation later can read
it in a normal top to bottom order rather than a bottom to top, or
worse yet, some combination.
On Tue, May 10, 2016 at 8:28 AM, nick83ola <nick83ola at gmail.com> wrote:
> enabling kernel debug on all modules it says:
>
> sound/soc/fsl/imx-pcm-fiq.c:226 [imx_pcm_fiq]snd_imx_pcm_mmap =_ "%s: ret:
> %d %p 0x%08x 0x%08x\012"
> sound/soc/fsl/fsl_ssi.c:1289 [snd_soc_fsl_ssi]fsl_ssi_imx_probe =_ "could
> not get baud clock: %ld\012"
> sound/soc/fsl/imx-audmux.c:333 [snd_soc_imx_audmux]imx_audmux_probe =p
> "cannot get clock: %ld\012"
> sound/soc/generic/simple-card.c:180
> [snd_soc_simple_card]asoc_simple_card_parse_of =p "card-name : %s\012"
> sound/soc/generic/simple-card.c:181
> [snd_soc_simple_card]asoc_simple_card_parse_of =p "platform : %04x\012"
> sound/soc/generic/simple-card.c:185
> [snd_soc_simple_card]asoc_simple_card_parse_of =p "cpu : %s / %04x / %d\012"
> sound/soc/generic/simple-card.c:189
> [snd_soc_simple_card]asoc_simple_card_parse_of =p "codec : %s / %04x /
> %d\012"
> sound/soc/generic/simple-card.c:33
> [snd_soc_simple_card]__asoc_simple_card_dai_init =p "ASoC: set_fmt is not
> supported\012"
>
> 2016-05-10 16:57 GMT+02:00 nick83ola <nick83ola at gmail.com>:
>>
>> Hello Caleb
>> thanks for your help
>>
>> Here's my current dts
>> I want to use ssi1 on port 4
>> I added #sound-dai-cells = <0>; on ssi1 because simple card complaijning
>> about it (what is that?? I could not find documentation about it)
Yeah, I don't really understand how that stuff works. I just have a
working setup, so I go with it.
>>
>> Now the driver says:
>> asoc-simple-card sound.26: snd-soc-dummy-dai <-> 2028000.ssi mapping ok
Yay!
>>
>> and
>>
>> > aplay -l
>>
>> **** List of PLAYBACK Hardware Devices ****
>> card 0: D2028000ssisnds [2028000.ssi-snd-soc-dummy-dai], device 0:
>> 2028000.ssi-snd-soc-dummy-dai snd-soc-dummy-dai-0 []
>> Subdevices: 1/1
>> Subdevice #0: subdevice #0
>>
>> > aplay -L
>>
>> null
>> Discard all samples (playback) or generate zero samples (capture)
>> sysdefault:CARD=D2028000ssisnds
>> 2028000.ssi-snd-soc-dummy-dai,
>> Default Audio Device
Are you using the new kernel I pointed you to (v4.5) , or still the
old 3.14? I don't have my system up right now to check against what
mine looks like.
For the most part, people on this list are on the latest kernel, and
are not terribly motivated to go back and figure out problems with old
kernels.
>>
>> but if I try to play a file it hangs and nothing escape
>>
>> How I can debug the various modules? ssi, dma, ???
Well, the way I do it is with lots and lots of printk's, and a really
fast automated way to rebuild/copy/reboot the kernel (a custom
makefile that does it all for me).
I don't see anything obviously wrong with your DTS, but I'm no expert.
You might want to try with a v4.5 kernel to see if that makes any
difference. Sorry I can't be of more help, but kernel hacking is
definitely not my main job :-)
-Caleb
>>
>> how I can print debug messages?? (i cannot see the various dev_dbg no
>> matter what I try...)
>>
>>
>> ==================================================================
>> /dts-v1/;
>>
>> #include <dt-bindings/gpio/gpio.h>
>> #include <dt-bindings/sound/fsl-imx-audmux.h>
>>
>> #include "imx6dl.dtsi"
>> #include "imx6qdl-icore.dtsi"
>>
>> #define SSI_TEST_MASTER
>> /*
>> * port 4 is datasheet port 5 (aud5)
>> * port 6 is datasheet port 7 (ssi3)
>> */
>> #define AUDMUX_EXT_PORT 3
>> #define AUDMUX_INT_PORT 0
>> #define AUDMUX_INT_PORT_NAME port4
>>
>> &audmux {
>> /* pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_audmux_4>;*/
>> status = "okay";
>> };
>>
>> &ssi1 {
>> #sound-dai-cells = <0>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_audmux_4>;
>>
>> // select the a clock parent suitable for 48000 Hz sampling rate
>> assigned-clocks = <&clks IMX6QDL_CLK_SSI1_SEL>, <&clks
>> IMX6QDL_CLK_SSI1>;
>> assigned-clock-parents = <&clks IMX6QDL_CLK_PLL4_AUDIO_DIV>;
>> assigned-clock-rates = <0>, <49152000>;
>> fsl,mode = "i2s-master";
>> status = "okay";
>> };
>>
>> &audmux {
>> status = "okay";
>>
>> ssi1 {
>> fsl,audmux-port = <AUDMUX_INT_PORT>;
>> fsl,port-config = <
>> #ifdef SSI_TEST_MASTER
>> IMX_AUDMUX_V2_PTCR_SYN
>> #else
>> (IMX_AUDMUX_V2_PTCR_TFSDIR |
>> IMX_AUDMUX_V2_PTCR_TFSEL(AUDMUX_EXT_PORT) |
>> IMX_AUDMUX_V2_PTCR_TCLKDIR |
>> IMX_AUDMUX_V2_PTCR_TCSEL(AUDMUX_EXT_PORT) |
>> IMX_AUDMUX_V2_PTCR_SYN
>> )
>> #endif
>> IMX_AUDMUX_V2_PDCR_RXDSEL(AUDMUX_EXT_PORT)
>> >;
>> };
>>
>> AUDMUX_INT_PORT_NAME {
>> fsl,audmux-port = <AUDMUX_EXT_PORT>;
>> fsl,port-config = <
>> #ifdef SSI_TEST_MASTER
>> (IMX_AUDMUX_V2_PTCR_TFSDIR |
>> IMX_AUDMUX_V2_PTCR_TFSEL(AUDMUX_INT_PORT) |
>> IMX_AUDMUX_V2_PTCR_TCLKDIR |
>> IMX_AUDMUX_V2_PTCR_TCSEL(AUDMUX_INT_PORT) |
>> IMX_AUDMUX_V2_PTCR_SYN
>> )
>> #else
>> IMX_AUDMUX_V2_PTCR_SYN
>> #endif
>> IMX_AUDMUX_V2_PDCR_RXDSEL(AUDMUX_INT_PORT)
>> >;
>> };
>> };
>>
>>
>> / {
>> model = "Engicam i.CoreM6 DualLite/Solo starterkit";
>> compatible = "fsl,imx6-icore", "fsl,imx6dl";
>>
>> codec_test: codec_test {
>> compatible = "linux,snd-soc-dummy";
>> #sound-dai-cells = <0>;
>> };
>>
>> sound {
>> compatible = "simple-audio-card";
>> simple-audio-card,name = "test";
>> simple-audio-card,format="dsp_a";
>> simple-audio-card,frame-master = <&sound2_ssi>;
>> simple-audio-card,bitclock-master = <&sound2_ssi>;
>>
>> sound2_ssi: simple-audio-card,cpu {
>> sound-dai = <&ssi1>;
>> system-clock-frequency = <1536000>;
>> dai-tdm-slot-num = <2>;
>> dai-tdm-slot-width = <16>;
>> };
>>
>> sound2codec: simple-audio-card,codec {
>> sound-dai = <&codec_test>;
>> };
>> };
>>
>> };
>>
>> &iomuxc {
>> audmux {
>> pinctrl_audmux_1: audmux-1 {
>> fsl,pins = <
>> MX6QDL_PAD_SD2_DAT0__AUD4_RXD 0x130b0
>> MX6QDL_PAD_SD2_DAT3__AUD4_TXC 0x130b0
>> MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x110b0
>> MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x130b0
>> >;
>> };
>>
>> pinctrl_audmux_2: audmux-2 {
>> fsl,pins = <
>> MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
>> MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
>> MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
>> MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
>> >;
>> };
>>
>> pinctrl_audmux_3: audmux-3 {
>> fsl,pins = <
>> MX6QDL_PAD_DISP0_DAT16__AUD5_TXC 0x130b0
>> MX6QDL_PAD_DISP0_DAT18__AUD5_TXFS 0x130b0
>> MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x130b0
>> >;
>> };
>>
>> pinctrl_audmux_4: audmux-4 {
>> fsl,pins = <
>> MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0
>> MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x110b0
>> MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
>> MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0
>> >;
>> };
>> };
>> };
>>
>>
>>
>> 2016-05-09 19:21 GMT+02:00 Caleb Crome <caleb at crome.org>:
>>>
>>> On Mon, May 9, 2016 at 4:17 AM, nick83ola <nick83ola at gmail.com> wrote:
>>> > Dear Alsa, Caleb and Arnaud
>>> >
>>> > I need to output an i2s master stream from my IMX6 solo board
>>> >
>>> > my board have this configuration for sound: (it have an sgtl5000 codec
>>> > not
>>> > on module, but on dev board)
>>> >
>>> >
>>> > ==========================================================================
>>> > sound {
>>> > compatible = "fsl,imx6q-icore-sgtl5000",
>>> > "fsl,imx-audio-sgtl5000";
>>> > model = "imx6q-icore-sgtl5000";
>>> > ssi-controller = <&ssi1>;
>>> > audio-codec = <&codec>;
>>> > audio-routing =
>>> > "MIC_IN", "Mic Jack",
>>> > "Mic Jack", "Mic Bias",
>>> > "Headphone Jack", "HP_OUT";
>>> > mux-int-port = <2>;
>>> > mux-ext-port = <4>;
>>> > };
>>> > &ssi1 {
>>> > fsl,mode = "i2s-master";
>>> > status = "okay";
>>> > };
>>> >
>>> > &audmux {
>>> > pinctrl-names = "default";
>>> > pinctrl-0 = <&pinctrl_audmux_4>;
>>> > status = "okay";
>>> > };
>>> >
>>> > &iomuxc {
>>> > audmux {
>>> > pinctrl_audmux_4: audmux-4 {
>>> > fsl,pins = <
>>> > MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0
>>> > MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x110b0
>>> > MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
>>> > MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0
>>> > >;
>>> > };
>>> > };
>>> >
>>> > ==========================================================================
>>> >
>>> > I need to output i2s on the same port as sgtl5000, bit in master mode
>>> > i've patched sound/soc/soc-utils.c to add support for dts as per arnaud
>>> > patch
>>> >
>>> >
>>> > ==========================================================================
>>> > #ifdef CONFIG_OF
>>> > static const struct of_device_id soc_dummy_ids[] = {
>>> > { .compatible = "linux,snd-soc-dummy", },
>>> > { }
>>> > };
>>> > MODULE_DEVICE_TABLE(of, soc_dummy_ids);
>>> > #endif
>>> > ...
>>> > .of_match_table = of_match_ptr(soc_dummy_ids),
>>> >
>>> > ==========================================================================
>>> >
>>> > --> (it is necessary?????? or can I use simple audio card??????
>>> >
>>> >
>>> > -> i've put this in my dts file
>>> >
>>> >
>>> > ==========================================================================
>>> > &audmux {
>>> > ssi3 {
>>> > fsl,audmux-port = <6>;
>>> > fsl,port-config = <
>>> > 0x00000000
>>> > IMX_AUDMUX_V2_PDCR_RXDSEL(4)
>>> > >;
>>> > };
>>> >
>>> > port5 {
>>> > fsl,audmux-port = <4>;
>>> > fsl,port-config = <
>>> > (IMX_AUDMUX_V2_PTCR_TFSDIR |
>>> > IMX_AUDMUX_V2_PTCR_TFSEL(6) |
>>> > IMX_AUDMUX_V2_PTCR_TCLKDIR |
>>> > IMX_AUDMUX_V2_PTCR_TCSEL(6))
>>> > IMX_AUDMUX_V2_PDCR_RXDSEL(6)
>>> > >;
>>> > };
>>> > };
>>> >
>>> > &ssi1 {
>>> > status = "disabled";
>>> > };
>>> >
>>> > &ssi2 {
>>> > status = "disabled";
>>> > };
>>> >
>>> > &ssi3 {
>>> > status = "okay";
>>> > #sound-dai-cells = <0>;
>>> > // select the a clock parent suitable for 48000 Hz sampling rate
>>> > assigned-clocks = <&clks IMX6QDL_CLK_SSI3_SEL>, <&clks
>>> > IMX6QDL_CLK_SSI3>;
>>> > assigned-clock-parents = <&clks IMX6QDL_CLK_PLL4_AUDIO_DIV>;
>>> > assigned-clock-rates = <0>, <49152000>;
>>> > };
>>> >
>>> > / {
>>> > model = "Engicam i.CoreM6 DualLite/Solo starterkit";
>>> > compatible = "fsl,imx6-icore", "fsl,imx6dl";
>>> >
>>> > sound{
>>> > status = "disabled";
>>> > };
>>> >
>>> > sound-itel {
>>> > compatible = "simple-audio-card";
>>> > simple-audio-card,name = "test";
>>> > simple-audio-card,format="dsp_a";
>>> > simple-audio-card,frame-master = <&sound2_ssi>;
>>> > simple-audio-card,bitclock-master = <&sound2_ssi>;
>>> > sound2_ssi: simple-audio-card,cpu {
>>> > sound-dai = <&ssi3>;
>>> > system-clock-frequency = <1536000>;
>>> > dai-tdm-slot-num = <2>;
>>> > dai-tdm-slot-width = <16>;
>>> > };
>>> > };
>>> > };
>>> >
>>> > ==========================================================================
>>> >
>>> >
>>> > here's my log
>>> >
>>> > /sound-itel/simple-audio-card,cpu: arguments longer than property
>>> > asoc-simple-card sound-itel.31: parse error -22
>>> > asoc-simple-card: probe of sound-itel.31 failed with error -22
>>> >
>>> >
>>> >
>>>
>>>
>>> Hi Nikola,
>>> Here is my working setup for a wandboard with no i2c codecs.
>>>
>>>
>>> https://github.com/ccrome/linux-caleb-dev/blob/v4.5-caleb-wandboard/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
>>>
>>> You need to be sure to set up the audmux right. I'm not sure with
>>> that old kernel if everything with audmux works right or not -- I
>>> haven't tested it.
>>>
>>> That should get you pretty close to what you need for your board I
>>> suspect.
>>>
>>> That branch (v4.5-caleb-wandboard) will build and run the SSI3 port on
>>> AUD5 port, with the mx6 in master mode. And, with all arnaud's
>>> patches (included already in that repo), it will actually be robust.
>>>
>>> -caleb
>>>
>>>
>>>
>>>
>>>
>>>
>>> >
>>> >
>>> >
>>> >
>>> >
>>> >
>>> >
>>> >
>>> >
>>> > 2016-05-06 17:38 GMT+02:00 Caleb Crome <caleb at crome.org>:
>>> >>
>>> >> Hi there,
>>> >> Arnaud had a neat patch here that lets you set up a dummy sound
>>> >> card from the DTS.
>>> >>
>>> >>
>>> >>
>>> >> http://mailman.alsa-project.org/pipermail/alsa-devel/2015-November/100896.html
>>> >>
>>> >> With that patch, you can set up your DTS to simply start streaming, no
>>> >> codec or anything required, which should work for a codec with no I2C.
>>> >>
>>> >>
>>> >> Hope that helps,
>>> >> -Caleb
>>> >>
>>> >>
>>> >> On Thu, May 5, 2016 at 12:56 PM, nick83ola <nick83ola at gmail.com>
>>> >> wrote:
>>> >> > Hello Alsa dev!
>>> >> >
>>> >> > Anyone have an example of an i2s only driver for imx6 solo? I need a
>>> >> > driver
>>> >> > without i2c....
>>> >> > _______________________________________________
>>> >> > Alsa-devel mailing list
>>> >> > Alsa-devel at alsa-project.org
>>> >> > http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
>>> >
>>> >
>>> >
>>> >
>>> > --
>>> >
>>> > P.S. Le informazioni trasmesse attraverso la presente comunicazione
>>> > sono di
>>> > esclusiva
>>> > spettanza dell'effettivo destinatario. Nel caso in cui le stesse
>>> > raggiungessero, per
>>> > qualunque motivo, soggetti non interessati, questi ultimi vorranno
>>> > darne
>>> > immediata
>>> > notizia al mittente. In ogni caso, eventuali soggetti diversi dai
>>> > legittimi
>>> > destinatari
>>> > della presente comunicazione e dei dati contenuti negli allegati,
>>> > possono
>>> > essere
>>> > sanzionati ai sensi del T.U. sul trattamento dei dati personali d.lgs.
>>> > 196/2003, sia ai
>>> > sensi dell'art. 616 del Codice Penale che disciplina la violazione del
>>> > segreto sulla
>>> > corrispondenza.
>>
>>
>>
>>
>> --
>>
>> P.S. Le informazioni trasmesse attraverso la presente comunicazione sono
>> di esclusiva
>> spettanza dell'effettivo destinatario. Nel caso in cui le stesse
>> raggiungessero, per
>> qualunque motivo, soggetti non interessati, questi ultimi vorranno darne
>> immediata
>> notizia al mittente. In ogni caso, eventuali soggetti diversi dai
>> legittimi destinatari
>> della presente comunicazione e dei dati contenuti negli allegati, possono
>> essere
>> sanzionati ai sensi del T.U. sul trattamento dei dati personali d.lgs.
>> 196/2003, sia ai
>> sensi dell'art. 616 del Codice Penale che disciplina la violazione del
>> segreto sulla
>> corrispondenza.
>
>
>
>
> --
>
> P.S. Le informazioni trasmesse attraverso la presente comunicazione sono di
> esclusiva
> spettanza dell'effettivo destinatario. Nel caso in cui le stesse
> raggiungessero, per
> qualunque motivo, soggetti non interessati, questi ultimi vorranno darne
> immediata
> notizia al mittente. In ogni caso, eventuali soggetti diversi dai legittimi
> destinatari
> della presente comunicazione e dei dati contenuti negli allegati, possono
> essere
> sanzionati ai sensi del T.U. sul trattamento dei dati personali d.lgs.
> 196/2003, sia ai
> sensi dell'art. 616 del Codice Penale che disciplina la violazione del
> segreto sulla
> corrispondenza.
More information about the Alsa-devel
mailing list