[alsa-devel] [PATCH 1/4] ALSA: Add documentation about HD-audio DP MST

[libin.yang at linux.intel.com]

From: Libin Yang <libin.yang at linux.intel.com>

Add the documentation about HD-audio DP MST:
1. Overview
2. Jack

Others will be added later.

Signed-off-by: Libin Yang <libin.yang at linux.intel.com>
---
 Documentation/sound/alsa/HD-Audio-DP-MST-audio.txt | 78 ++++++++++++++++++++++
 1 file changed, 78 insertions(+)
 create mode 100644 Documentation/sound/alsa/HD-Audio-DP-MST-audio.txt

diff --git a/Documentation/sound/alsa/HD-Audio-DP-MST-audio.txt b/Documentation/sound/alsa/HD-Audio-DP-MST-audio.txt
new file mode 100644
index 0000000..ff28e55
--- /dev/null
+++ b/Documentation/sound/alsa/HD-Audio-DP-MST-audio.txt
@@ -0,0 +1,78 @@
+To support DP MST audio, HD Audio hdmi codec driver introduces virtual pin
+and dynamic pcm assignment.
+
+Virtual pin is an extension of per_pin. The most difference of DP MST
+from legacy is that DP MST introduces device entry. Each pin can contain
+several device entries. Each device entry behaves as a pin.
+
+As each pin may contain several device entries and each codec may contain
+several pins, if we use one pcm per per_pin, there will be many PCMs.
+The new solution is to create a few PCMs and to dynamically bind pcm to
+per_pin. Driver uses spec->dyn_pcm_assign flag to indicate whether to use
+the new solution.
+
+PCM
+===
+To be added
+
+
+Jack
+====
+
+Presume:
+ - MST must be dyn_pcm_assign, it can be acomp or !acomp;
+ - NON-MST may or may not be dyn_pcm_assign, it can be acomp or !acomp;
+
+So there are the following scenarios:
+ a.MST (&& dyn_pcm_assign) && acomp
+ b.MST (&& dyn_pcm_assign) && !acomp
+ c.NON-MST && dyn_pcm_assign && acomp
+ d.NON-MST && dyn_pcm_assign && !acomp
+ e.NON-MST && !dyn_pcm_assign && acomp
+ f.NON-MST && !dyn_pcm_assign && !acomp
+
+Below discussion will ignore MST and NON-MST difference as it doesn't
+impact on jack handling too much.
+
+Driver uses new struct hdmi_pcm pcm[] array in hdmi_spec and snd_jack is
+a member of hdmi_pcm. Each pin has one struct hdmi_pcm * pcm pointer.
+
+For !dyn_pcm_assign, per_pin->pcm will assigned to spec->pcm[n] statically.
+
+For dyn_pcm_assign, per_pin->pcm will assigned to spec->pcm[n]
+when monitor is hotplugged.
+
+
+Build Jack
+----------
+
+Build jack based on the pcm. acomp or !acomp will not impact on jack buiding.
+- dyn_pcm_assign
+Will not use hda_jack but use snd_jack in spec->pcm_rec[pcm_idx].jack directly.
+
+- !dyn_pcm_assign
+Use hda_jack and assign spec->pcm_rec[pcm_idx].jack = jack->jack statically.
+
+
+Unsolicited Event Enabling
+--------------------------
+Enable unsolicited event if !acomp.
+
+
+Monitor Hotplug Event Handling
+------------------------------
+- acomp
+pin_eld_notify() -> check_presence_and_report() -> hdmi_present_sense() ->
+sync_eld_via_acomp().
+Use directly snd_jack_report() on spec->pcm_rec[pcm_idx].jack for
+both dyn_pcm_assign and !dyn_pcm_assign
+
+- !acomp
+Hdmi_unsol_event() -> hdmi_intrinsic_event() -> check_presence_and_report() ->
+hdmi_present_sense() -> hdmi_prepsent_sense_via_verbs()
+Use directly snd_jack_report() on spec->pcm_rec[pcm_idx].jack for dyn_pcm_assign.
+Use hda_jack mechanism to handle jack events.
+
+
+Others to be added later
+========================
-- 
1.9.1