[alsa-devel] [PATCH v2 06/17] video: lcd: add LoCoMo LCD driver
Dmitry Eremin-Solenikov
dbaryshkov at gmail.com
Tue Apr 28 01:55:43 CEST 2015
LoCoMo has some special handling for TFT screens attached to Collie and
Poodle. Implement that as a separate driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov at gmail.com>
---
drivers/video/backlight/Kconfig | 10 ++
drivers/video/backlight/Makefile | 1 +
drivers/video/backlight/locomo_lcd.c | 285 +++++++++++++++++++++++++++++++++++
3 files changed, 296 insertions(+)
create mode 100644 drivers/video/backlight/locomo_lcd.c
diff --git a/drivers/video/backlight/Kconfig b/drivers/video/backlight/Kconfig
index 6c093e2..b2f995c 100644
--- a/drivers/video/backlight/Kconfig
+++ b/drivers/video/backlight/Kconfig
@@ -48,6 +48,16 @@ config LCD_LMS283GF05
SPI driver for Samsung LMS283GF05. This provides basic support
for powering the LCD up/down through a sysfs interface.
+config LCD_LOCOMO
+ tristate "Sharp LOCOMO LCD Driver"
+ depends on MFD_LOCOMO
+ select IIO
+ help
+ If you have a Sharp Zaurus SL-5500 (Collie) or SL-5600 (Poodle) say y to
+ enable the LCD driver. The panel starts up in power
+ off state, so you need this driver in order to see any
+ output.
+
config LCD_LTV350QV
tristate "Samsung LTV350QV LCD Panel"
depends on SPI_MASTER
diff --git a/drivers/video/backlight/Makefile b/drivers/video/backlight/Makefile
index 2de73d2..686cf1a 100644
--- a/drivers/video/backlight/Makefile
+++ b/drivers/video/backlight/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_LCD_L4F00242T03) += l4f00242t03.o
obj-$(CONFIG_LCD_LD9040) += ld9040.o
obj-$(CONFIG_LCD_LMS283GF05) += lms283gf05.o
obj-$(CONFIG_LCD_LMS501KF03) += lms501kf03.o
+obj-$(CONFIG_LCD_LOCOMO) += locomo_lcd.o
obj-$(CONFIG_LCD_LTV350QV) += ltv350qv.o
obj-$(CONFIG_LCD_PLATFORM) += platform_lcd.o
obj-$(CONFIG_LCD_S6E63M0) += s6e63m0.o
diff --git a/drivers/video/backlight/locomo_lcd.c b/drivers/video/backlight/locomo_lcd.c
new file mode 100644
index 0000000..dc316cb
--- /dev/null
+++ b/drivers/video/backlight/locomo_lcd.c
@@ -0,0 +1,285 @@
+/*
+ * Backlight control code for Sharp Zaurus SL-5500
+ *
+ * Copyright 2005 John Lenz <lenz at cs.wisc.edu>
+ * Maintainer: Pavel Machek <pavel at ucw.cz> (unless John wants to :-)
+ * GPL v2
+ *
+ * This driver assumes single CPU. That's okay, because collie is
+ * slightly old hardware, and no one is going to retrofit second CPU to
+ * old PDA.
+ */
+
+#include <linux/delay.h>
+#include <linux/fb.h>
+#include <linux/gpio/consumer.h>
+#include <linux/iio/consumer.h>
+#include <linux/lcd.h>
+#include <linux/mfd/locomo.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+struct locomo_lcd {
+ struct regmap *regmap;
+ struct platform_device *dev;
+ struct locomo_lcd_platform_data *data;
+ int power;
+ struct iio_channel *comadj;
+ struct gpio_desc *vsha, *vshd, *vee, *mod;
+};
+
+static void locomo_lcd_on(struct locomo_lcd *lcd)
+{
+ gpiod_set_value(lcd->vsha, 1);
+ usleep_range(2000, 3000);
+
+ gpiod_set_value(lcd->vshd, 1);
+ usleep_range(2000, 3000);
+
+ iio_write_channel_raw(lcd->comadj, lcd->data->comadj);
+ usleep_range(5000, 6000);
+
+ gpiod_set_value(lcd->vee, 1);
+ usleep_range(10000, 11000);
+
+ /* TFTCRST | CPSOUT=0 | CPSEN */
+ regmap_write(lcd->regmap, LOCOMO_TC, 0x01);
+
+ /* Set CPSD */
+ regmap_write(lcd->regmap, LOCOMO_CPSD, 6);
+
+ /* TFTCRST | CPSOUT=0 | CPSEN */
+ regmap_write(lcd->regmap, LOCOMO_TC, 0x04 | 0x01);
+ usleep_range(10000, 11000);
+
+ gpiod_set_value(lcd->mod, 1);
+}
+
+static void locomo_lcd_off(struct locomo_lcd *lcd)
+{
+ /* TFTCRST=1 | CPSOUT=1 | CPSEN = 0 */
+ regmap_write(lcd->regmap, LOCOMO_TC, 0x06);
+ usleep_range(1000, 2000);
+
+ gpiod_set_value(lcd->vsha, 0);
+ msleep(110);
+
+ gpiod_set_value(lcd->vee, 0);
+ msleep(700);
+
+ iio_write_channel_raw(lcd->comadj, 0);
+ usleep_range(5000, 6000);
+
+ /* TFTCRST=0 | CPSOUT=0 | CPSEN = 0 */
+ regmap_write(lcd->regmap, LOCOMO_TC, 0);
+ gpiod_set_value(lcd->mod, 0);
+ gpiod_set_value(lcd->vshd, 0);
+}
+
+static void locomo_lcd_program_adsync(struct locomo_lcd *lcd)
+{
+ regmap_write(lcd->regmap, LOCOMO_ASD,
+ 6 + 8 + 320 + 30 - 10);
+ regmap_update_bits(lcd->regmap, LOCOMO_ASD,
+ 0x8000,
+ 0x8000);
+
+ regmap_write(lcd->regmap, LOCOMO_HSD,
+ 6 + 8 + 320 + 30 - 10 - 128 + 4);
+ regmap_update_bits(lcd->regmap, LOCOMO_HSD,
+ 0x8000,
+ 0x8000);
+
+ regmap_write(lcd->regmap, LOCOMO_HSC, 128 / 8);
+
+ /* XON */
+ regmap_write(lcd->regmap, LOCOMO_TADC, 0x80);
+ usleep_range(1000, 1100);
+
+ /* CLK9MEN */
+ regmap_update_bits(lcd->regmap, LOCOMO_TADC,
+ 0x10,
+ 0x10);
+ usleep_range(100, 200);
+}
+
+static void locomo_lcd_disable_adsync(struct locomo_lcd *lcd)
+{
+ /* ADSTART */
+ regmap_write(lcd->regmap, LOCOMO_ASD, 0x00);
+
+ /* 18MHz clock off*/
+ regmap_write(lcd->regmap, LOCOMO_TADC, 0x00);
+}
+
+int locomo_lcd_set_power(struct lcd_device *ldev, int power)
+{
+ struct locomo_lcd *lcd = lcd_get_data(ldev);
+
+ dev_dbg(&ldev->dev, "LCD power %d (is %d)\n", power, lcd->power);
+
+ if (!power && lcd->power)
+ locomo_lcd_on(lcd);
+
+ if (power && !lcd->power)
+ locomo_lcd_off(lcd);
+
+ lcd->power = power;
+
+ return 0;
+}
+
+static int locomo_lcd_get_power(struct lcd_device *ldev)
+{
+ struct locomo_lcd *lcd = lcd_get_data(ldev);
+
+ return lcd->power;
+}
+
+static struct lcd_ops locomo_lcd_ops = {
+ .set_power = locomo_lcd_set_power,
+ .get_power = locomo_lcd_get_power,
+};
+
+#ifdef CONFIG_PM_SLEEP
+static int locomo_lcd_suspend(struct device *dev)
+{
+ struct lcd_device *ldev = dev_get_drvdata(dev);
+ struct locomo_lcd *lcd = lcd_get_data(ldev);
+
+ locomo_lcd_off(lcd);
+
+ locomo_lcd_disable_adsync(lcd);
+
+ return 0;
+}
+
+static int locomo_lcd_resume(struct device *dev)
+{
+ struct lcd_device *ldev = dev_get_drvdata(dev);
+ struct locomo_lcd *lcd = lcd_get_data(ldev);
+
+ locomo_lcd_program_adsync(lcd);
+
+ if (!lcd->power)
+ locomo_lcd_on(lcd);
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(locomo_lcd_pm, locomo_lcd_suspend, locomo_lcd_resume);
+#define LOCOMOLCD_PM (&locomo_lcd_pm)
+#else
+#define LOCOMOLCD_PM NULL
+#endif
+
+static int locomo_lcd_probe(struct platform_device *dev)
+{
+ struct lcd_device *lcd_dev;
+ struct locomo_lcd *lcd;
+ int rc;
+
+ lcd = devm_kmalloc(&dev->dev, sizeof(struct locomo_lcd), GFP_KERNEL);
+ if (!lcd)
+ return -ENOMEM;
+
+ lcd->dev = dev;
+ lcd->power = FB_BLANK_NORMAL;
+
+ lcd->regmap = dev_get_regmap(dev->dev.parent, NULL);
+ if (!lcd->regmap)
+ return -ENODEV;
+
+ lcd->data = dev_get_platdata(&dev->dev);
+ if (!lcd->data)
+ return -EINVAL;
+
+ lcd->vsha = devm_gpiod_get(&dev->dev, "VSHA", GPIOD_OUT_LOW);
+ if (IS_ERR(lcd->vsha))
+ return PTR_ERR(lcd->vsha);
+
+ lcd->vshd = devm_gpiod_get(&dev->dev, "VSHD", GPIOD_OUT_LOW);
+ if (IS_ERR(lcd->vshd))
+ return PTR_ERR(lcd->vshd);
+
+ lcd->vee = devm_gpiod_get(&dev->dev, "Vee", GPIOD_OUT_LOW);
+ if (IS_ERR(lcd->vee))
+ return PTR_ERR(lcd->vee);
+
+ lcd->mod = devm_gpiod_get(&dev->dev, "MOD", GPIOD_OUT_LOW);
+ if (IS_ERR(lcd->mod))
+ return PTR_ERR(lcd->mod);
+
+ lcd->comadj = iio_channel_get(&dev->dev, "comadj");
+ if (IS_ERR(lcd->comadj)) {
+ rc = PTR_ERR(lcd->comadj);
+ if (rc == -ENODEV)
+ rc = -EPROBE_DEFER;
+
+ return rc;
+ }
+
+ locomo_lcd_program_adsync(lcd);
+
+ lcd_dev = devm_lcd_device_register(&dev->dev, "locomo", &dev->dev, lcd,
+ &locomo_lcd_ops);
+ if (IS_ERR(lcd_dev)) {
+ rc = PTR_ERR(lcd_dev);
+ goto err;
+ }
+
+ platform_set_drvdata(dev, lcd_dev);
+
+ lcd_set_power(lcd_dev, FB_BLANK_UNBLANK);
+
+ return 0;
+
+err:
+ locomo_lcd_disable_adsync(lcd);
+ iio_channel_release(lcd->comadj);
+
+ return rc;
+}
+
+static int locomo_lcd_remove(struct platform_device *dev)
+{
+ struct lcd_device *ldev = platform_get_drvdata(dev);
+ struct locomo_lcd *lcd = lcd_get_data(ldev);
+
+ locomo_lcd_off(lcd);
+
+ locomo_lcd_disable_adsync(lcd);
+
+ iio_channel_release(lcd->comadj);
+
+ return 0;
+}
+
+static void locomo_lcd_shutdown(struct platform_device *dev)
+{
+ struct lcd_device *ldev = platform_get_drvdata(dev);
+ struct locomo_lcd *lcd = lcd_get_data(ldev);
+
+ locomo_lcd_off(lcd);
+
+ locomo_lcd_disable_adsync(lcd);
+}
+
+static struct platform_driver locomo_lcd_driver = {
+ .driver = {
+ .name = "locomo-lcd",
+ .pm = LOCOMOLCD_PM,
+ },
+ .probe = locomo_lcd_probe,
+ .remove = locomo_lcd_remove,
+ .shutdown = locomo_lcd_shutdown,
+};
+
+module_platform_driver(locomo_lcd_driver);
+
+MODULE_AUTHOR("John Lenz <lenz at cs.wisc.edu>");
+MODULE_AUTHOR("Pavel Machek <pavel at ucw.cz>");
+MODULE_DESCRIPTION("LoCoMo LCD driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:locomo-lcd");
--
2.1.4
More information about the Alsa-devel
mailing list