[alsa-devel] [PATCH v2 1/2] ASoC: Add support for CS35L32 Boosted Amplifier
Brian Austin
brian.austin at cirrus.com
Mon Aug 4 16:44:04 CEST 2014
On Sat, 2 Aug 2014, Dinh Nguyen wrote:
>
> On 8/1/14, 9:45 AM, Brian Austin wrote:
> > This patch adds support for the Cirrus Logic CS35L32 Boosted Amplifier
> > I2S output provides monitor data to the SOC/CODEC/DSP for speaker protection algorithms
> >
> > Changes for v2:
> > - Interrupt Status registers added to regmap volatile
> > - Use Speaker for volume control name
> > - Zero Cross Switch rename
> > - Remove Gain Manager from DTS and add to kcontrols
> > - Add VP-Supply to regulator list
> > - Remove uneeded DAPM event
> > - Specify MCLK rates as numbers
> > - Move probe/remove code to device level probe/remove
> > - Move regmap_register_patch to after REV_ID check
> >
> > Signed-off-by: Brian Austin <brian.austin at cirrus.com>
> > ---
> > +static int cs35l32_handle_of_data(struct i2c_client *i2c_client,
> > + struct cs35l32_platform_data *pdata)
> > +{
> > + struct device_node *np = i2c_client->dev.of_node;
> > + unsigned int val;
> > +
> > + if (of_property_read_u32(np, "cirrus,sdout-share", &val) >= 0)
> > + pdata->sdout_share = val;
> > +
> > + of_property_read_u32(np, "cirrus,boost-manager", &val);
> > + switch (val) {
> > + case CS35L32_BOOST_MGR_AUTO:
> > + case CS35L32_BOOST_MGR_AUTO_AUDIO:
> > + case CS35L32_BOOST_MGR_BYPASS:
> > + case CS35L32_BOOST_MGR_FIXED:
> > + pdata->boost_mng = val;
> > + break;
> > + default:
> > + dev_err(&i2c_client->dev,
> > + "Wrong cirrus,boost-manager DT value %d\n", val);
> > + pdata->boost_mng = CS35L32_BOOST_MGR_BYPASS;
> > + }
> > +
> > + of_property_read_u32(np, "cirrus,sdout-datacfg", &val);
> > + switch (val) {
> > + case CS35L32_DATA_CFG_LR_VP:
> > + case CS35L32_DATA_CFG_LR_STAT:
> > + case CS35L32_DATA_CFG_LR:
> > + case CS35L32_DATA_CFG_LR_VPSTAT:
> > + pdata->sdout_datacfg = val;
> > + break;
> > + default:
> > + dev_err(&i2c_client->dev,
> > + "Wrong cirrus,sdout-datacfg DT value %d\n", val);
> > + pdata->sdout_datacfg = CS35L32_DATA_CFG_LR;
> > + }
> > +
> > + of_property_read_u32(np, "cirrus,battery-threshold", &val);
> > + switch (val) {
> > + case CS35L32_BATT_THRESH_3_1V:
> > + case CS35L32_BATT_THRESH_3_2V:
> > + case CS35L32_BATT_THRESH_3_3V:
> > + case CS35L32_BATT_THRESH_3_4V:
> > + pdata->batt_thresh = val;
> > + break;
> > + default:
> > + dev_err(&i2c_client->dev,
> > + "Wrong cirrus,battery-threshold DT value %d\n", val);
> > + pdata->batt_thresh = CS35L32_BATT_THRESH_3_3V;
> > + }
> > +
> > + of_property_read_u32(np, "cirrus,battery-recovery", &val);
> > + switch (val) {
> > + case CS35L32_BATT_RECOV_3_1V:
> > + case CS35L32_BATT_RECOV_3_2V:
> > + case CS35L32_BATT_RECOV_3_3V:
> > + case CS35L32_BATT_RECOV_3_4V:
> > + case CS35L32_BATT_RECOV_3_5V:
> > + case CS35L32_BATT_RECOV_3_6V:
> > + pdata->batt_recov = val;
> > + break;
> > + default:
> > + dev_err(&i2c_client->dev,
> > + "Wrong cirrus,battery-recovery DT value %d\n", val);
> > + pdata->batt_recov = CS35L32_BATT_RECOV_3_4V;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int cs35l32_i2c_probe(struct i2c_client *i2c_client,
> > + const struct i2c_device_id *id)
> > +{
> > + struct cs35l32_private *cs35l32;
> > + struct cs35l32_platform_data *pdata =
> > + dev_get_platdata(&i2c_client->dev);
> > + int ret, i;
> > + unsigned int devid = 0;
> > + unsigned int reg;
> > +
> > +
> > + cs35l32 = devm_kzalloc(&i2c_client->dev, sizeof(struct cs35l32_private),
> > + GFP_KERNEL);
> > + if (!cs35l32) {
> > + dev_err(&i2c_client->dev, "could not allocate codec\n");
> > + return -ENOMEM;
> > + }
> > +
> > + i2c_set_clientdata(i2c_client, cs35l32);
> > +
> > + cs35l32->regmap = devm_regmap_init_i2c(i2c_client, &cs35l32_regmap);
> > + if (IS_ERR(cs35l32->regmap)) {
> > + ret = PTR_ERR(cs35l32->regmap);
> > + dev_err(&i2c_client->dev, "regmap_init() failed: %d\n", ret);
> > + return ret;
> > + }
> > +
> > + if (pdata) {
> > + cs35l32->pdata = *pdata;
> > + } else {
> > + pdata = devm_kzalloc(&i2c_client->dev,
> > + sizeof(struct cs35l32_platform_data),
> > + GFP_KERNEL);
> > + if (!pdata) {
> > + dev_err(&i2c_client->dev, "could not allocate pdata\n");
> > + return -ENOMEM;
> > + }
> > + if (i2c_client->dev.of_node) {
> > + ret = cs35l32_handle_of_data(i2c_client,
> > + &cs35l32->pdata);
> > + if (ret != 0)
> > + return ret;
>
> Doesn't cs35l32_handle_of_data() always return 0?
>
I thought about this and I think I am going to keep this check incase I
change anything about handle_of_data and would like to check the return
value. I don't think it causes anything bad to keep it. I always like to
have this check just in case.
> > + }
> > + }
> > +
> > + for (i = 0; i < ARRAY_SIZE(cs35l32->supplies); i++)
> > + cs35l32->supplies[i].supply = cs35l32_supply_names[i];
> > +
> > + ret = devm_regulator_bulk_get(&i2c_client->dev,
> > + ARRAY_SIZE(cs35l32->supplies),
> > + cs35l32->supplies);
> > + if (ret != 0) {
> > + dev_err(&i2c_client->dev,
> > + "Failed to request supplies: %d\n", ret);
> > + return ret;
> > + }
> > +
> > + ret = regulator_bulk_enable(ARRAY_SIZE(cs35l32->supplies),
> > + cs35l32->supplies);
> > + if (ret != 0) {
> > + dev_err(&i2c_client->dev,
> > + "Failed to enable supplies: %d\n", ret);
> > + return ret;
> > + }
> > +
> > + /* Reset the Device */
> > + cs35l32->reset_gpio = devm_gpiod_get(&i2c_client->dev,
> > + "reset-gpios");
> > + if (IS_ERR(cs35l32->reset_gpio)) {
> > + ret = PTR_ERR(cs35l32->reset_gpio);
> > + if (ret != -ENOENT && ret != -ENOSYS)
> > + return ret;
> > +
> > + cs35l32->reset_gpio = NULL;
> > + } else {
> > + ret = gpiod_direction_output(cs35l32->reset_gpio, 0);
> > + if (ret)
> > + return ret;
> > + gpiod_set_value_cansleep(cs35l32->reset_gpio, 1);
> > + }
> > +
> > + /* initialize codec */
> > + ret = regmap_read(cs35l32->regmap, CS35L32_DEVID_AB, ®);
> > + devid = (reg & 0xFF) << 12;
> > +
> > + ret = regmap_read(cs35l32->regmap, CS35L32_DEVID_CD, ®);
> > + devid |= (reg & 0xFF) << 4;
> > +
> > + ret = regmap_read(cs35l32->regmap, CS35L32_DEVID_E, ®);
> > + devid |= (reg & 0xF0) >> 4;
> > +
> > + if (devid != CS35L32_CHIP_ID) {
> > + ret = -ENODEV;
> > + dev_err(&i2c_client->dev,
> > + "CS35L32 Device ID (%X). Expected %X\n",
> > + devid, CS35L32_CHIP_ID);
> > + return ret;
> > + }
> > +
> > + ret = regmap_read(cs35l32->regmap, CS35L32_REV_ID, ®);
> > + if (ret < 0) {
> > + dev_err(&i2c_client->dev, "Get Revision ID failed\n");
> > + return ret;
> > + }
> > +
> > + ret = regmap_register_patch(cs35l32->regmap, cs35l32_monitor_patch,
> > + ARRAY_SIZE(cs35l32_monitor_patch));
> > + if (ret < 0) {
> > + dev_err(&i2c_client->dev, "Failed to apply errata patch\n");
> > + return ret;
> > + }
> > +
> > + dev_info(&i2c_client->dev,
> > + "Cirrus Logic CS35L32, Revision: %02X\n", reg & 0xFF);
> > +
> > + /* Setup VBOOST Management */
> > + if (cs35l32->pdata.boost_mng)
> > + regmap_update_bits(cs35l32->regmap, CS35L32_AUDIO_LED_MNGR,
> > + CS35L32_BOOST_MASK,
> > + cs35l32->pdata.boost_mng);
> > +
> > + /* Setup ADSP Format Config */
> > + if (cs35l32->pdata.sdout_share)
> > + regmap_update_bits(cs35l32->regmap, CS35L32_ADSP_CTL,
> > + CS35L32_ADSP_SHARE_MASK,
> > + cs35l32->pdata.sdout_share << 3);
> > +
> > + /* Setup ADSP Data Configuration */
> > + if (cs35l32->pdata.sdout_datacfg)
> > + regmap_update_bits(cs35l32->regmap, CS35L32_ADSP_CTL,
> > + CS35L32_ADSP_DATACFG_MASK,
> > + cs35l32->pdata.sdout_datacfg << 4);
> > +
> > + /* Setup Low Battery Recovery */
> > + if (cs35l32->pdata.batt_recov)
> > + regmap_update_bits(cs35l32->regmap, CS35L32_BATT_THRESHOLD,
> > + CS35L32_BATT_REC_MASK,
> > + cs35l32->pdata.batt_recov << 1);
> > +
> > + /* Setup Low Battery Threshold */
> > + if (cs35l32->pdata.batt_thresh)
> > + regmap_update_bits(cs35l32->regmap, CS35L32_BATT_THRESHOLD,
> > + CS35L32_BATT_THRESH_MASK,
> > + cs35l32->pdata.batt_thresh << 4);
> > +
> > + /* Power down the AMP */
> > + regmap_update_bits(cs35l32->regmap, CS35L32_PWRCTL1, CS35L32_PDN_AMP,
> > + CS35L32_PDN_AMP);
> > +
> > + /* Clear MCLK Error Bit since we don't have the clock yet */
> > + ret = regmap_read(cs35l32->regmap, CS35L32_INT_STATUS_1, ®);
> > +
> > + ret = snd_soc_register_codec(&i2c_client->dev,
> > + &soc_codec_dev_cs35l32, cs35l32_dai,
> > + ARRAY_SIZE(cs35l32_dai));
> > +
> > + if (ret < 0)
> > + return ret;
> > + return 0;
>
> Should be able to just "return ret" here.
I will change this but related to the regulator in case
snd_soc_register_codec fails.
Thanks,
Brian
More information about the Alsa-devel
mailing list