[alsa-devel] [PATCH] ASoC: Add PCM1681 codec driver.

Lars-Peter Clausen lars at metafoo.de
Mon Jul 1 14:37:09 CEST 2013


On 06/26/2013 03:05 PM, Marek Belisko wrote:
[...]
> +static int pcm1681_deemph[] = { 44100, 48000, 32000 };

const

> +
> +static int pcm1681_set_deemph(struct snd_soc_codec *codec)
> +{
> +	struct pcm1681_private *priv = snd_soc_codec_get_drvdata(codec);
> +	int i = 0, val = -1, ret;
> +
> +	if (priv->deemph)
> +		for (i = 0; i < ARRAY_SIZE(pcm1681_deemph); i++)
> +			if (pcm1681_deemph[i] == priv->rate)
> +				val = i;
> +
> +	/* enable choosen frequency */
> +	if (val != -1)
> +		regmap_update_bits(priv->regmap, PCM1681_DEEMPH_CONTROL,
> +					PCM1681_DEEMPH_RATE_MASK, val);

So if the current sample rate doesn't match any of the available deempth rates
the current setting is kept. This doesn't seem right.

> +
> +	/* enable/disable deemphasis functionality */
> +	ret = regmap_update_bits(priv->regmap, PCM1681_DEEMPH_CONTROL,
> +				PCM1681_DEEMPH_MASK, priv->deemph);
> +
> +	return ret;
> +}
> +
[...]
> +
> +static int pcm1681_digital_mute(struct snd_soc_dai *dai, int mute)
> +{
> +	struct snd_soc_codec *codec = dai->codec;
> +	struct pcm1681_private *priv = snd_soc_codec_get_drvdata(codec);
> +	int ret, val = 0;
> +
> +	if (mute)
> +		val = PCM1681_SOFT_MUTE_ALL;
> +
> +	ret = regmap_write(priv->regmap, PCM1681_SOFT_MUTE, val);

How about just

return regmap_write(...)

> +	if (ret < 0)
> +		return ret;
> +
> +	return 0;
> +}
> +
[...]
> +static const DECLARE_TLV_DB_SCALE(pcm1681_dac_tlv, -6350, 50, 1);
> +
> +static const struct snd_kcontrol_new pcm1681_controls[] = {
> +	SOC_DOUBLE_R_TLV("PCM1681 Channel 1/2 Playback Volume",
> +			PCM1681_ATT_CONTROL(1), PCM1681_ATT_CONTROL(2), 0,
> +			0x7f, 0, pcm1681_dac_tlv),
> +	SOC_DOUBLE_R_TLV("PCM1681 Channel 3/4 Playback Volume",
> +			PCM1681_ATT_CONTROL(3), PCM1681_ATT_CONTROL(4), 0,
> +			0x7f, 0, pcm1681_dac_tlv),
> +	SOC_DOUBLE_R_TLV("PCM1681 Channel 5/6 Playback Volume",
> +			PCM1681_ATT_CONTROL(5), PCM1681_ATT_CONTROL(6), 0,
> +			0x7f, 0, pcm1681_dac_tlv),
> +	SOC_DOUBLE_R_TLV("PCM1681 Channel 7/8 Playback Volume",
> +			PCM1681_ATT_CONTROL(7), PCM1681_ATT_CONTROL(8), 0,
> +			0x7f, 0, pcm1681_dac_tlv),
> +	SOC_SINGLE_BOOL_EXT("PCM1681 De-emphasis Switch", 0,
> +			    pcm1681_get_deemph, pcm1681_put_deemph),
> +};

The name of the codec should probably not be in the control names.

[...]
> +#ifdef CONFIG_OF
> +static const struct of_device_id pcm1681_dt_ids[] = {
> +	{ .compatible = "ti,pcm1681", },
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(of, pcm1681_dt_ids);
> +#endif
> +
> +static const struct regmap_config pcm1681_regmap = {
> +	.reg_bits		= 8,
> +	.val_bits		= 8,
> +	.max_register		= ARRAY_SIZE(pcm1681_reg_defaults),

max_register is the last register in the register map, so usually this would be
ARRAY_SIZE(...) + 1

> +	.reg_defaults		= pcm1681_reg_defaults,
> +	.num_reg_defaults	= ARRAY_SIZE(pcm1681_reg_defaults),
> +	.writeable_reg		= pcm1681_writeable_reg,
> +	.readable_reg		= pcm1681_accessible_reg,
> +};
[...]
> +
> +static struct snd_soc_codec_driver soc_codec_dev_pcm1681 = {
> +	.probe			= pcm1681_probe,
> +	.remove			= pcm1681_remove,
> +	.controls		= pcm1681_controls,
> +	.num_controls		= ARRAY_SIZE(pcm1681_controls),
> +};
> +
> +#if defined(CONFIG_I2C) || defined(CONFIG_I2C_MODULE)

Since the driver only supports I2C there is no need for this ifdef
[...]



More information about the Alsa-devel mailing list