[alsa-devel] Clevo P170HM / Sager NP8170 audio
Julian Sikorski
belegdol at gmail.com
Tue Nov 22 13:45:20 CET 2011
W dniu 22.11.2011 06:17, Raymond Yau pisze:
> 2011/11/21 Julian Sikorski <belegdol at gmail.com>:
>> W dniu 21.11.2011 07:47, Raymond Yau pisze:
>>> 2011/11/19 Julian Sikorski <belegdol at gmail.com>:
>>>>>> From the official (non-service) manual, page 309:
>>>>>>
>>>>>
>>>>> Refer to P170HM 's photo in user manual
>>>>>
>>>>> There are 3 speakers and a subwoofer at the bottom of the laptop and
>>>>> two speakers at the top
>>>>>
>>>>> Refer to user manual of P150HM,
>>>>>
>>>>> Plug the front speaker cables into the Headphone-Out Jack.
>>>>>
>>>>> • Line-In Jack = Rear Speaker Out
>>>>> • Microphone-In Jack = Center/Subwoofer Speaker Out
>>>>> • S/PDIF-Out Jack = Side Speaker Out (for 7.1 Surround Sound Only)
>>>
>>> You may need to ask Takashi , David, PA developers and Media
>>> controller developers how to handle this case
>>>
>>> since it may need to set_pin_ctl to PIN_HP and PIN_OUT of 0x1b and
>>> retasking of input jacks as output whether PA or Media controller API
>>> expect to change the name of the volume control and switch from
>>> "Headphone" to "Front" by hda-reconfig
>>>
>>> http://thread.gmane.org/gmane.linux.alsa.devel/91334
>>>
>>>>>
>>>>> 7. As you plug in each cable a dialog box will pop up (see “Auto Popup
>>>>> Dialog” on
>>>>> page 2 - 9).
>>>>>
>>>>> Auto Popup Dialog mean support jack detect
>>>>>
>>>>> you can try David's hda-jack-sense-test.py
>>>>>
>>>>> http://thread.gmane.org/gmane.linux.alsa.devel/85051
>>>>
>>>> Yes, it is working:
>>>> [julas at snowball2 ~]$ sudo python hda-jack-sense-test.py
>>>> Pin 0x18 (Black Mic): present = No
>>>> Pin 0x1a (Black Line In): present = No
>>>> Pin 0x1b (Black HP Out): present = Yes
>>>> [julas at snowball2 ~]$ sudo python hda-jack-sense-test.py
>>>> Pin 0x18 (Black Mic): present = No
>>>> Pin 0x1a (Black Line In): present = No
>>>> Pin 0x1b (Black HP Out): present = No
>>>> [julas at snowball2 ~]$ sudo python hda-jack-sense-test.py
>>>> Pin 0x18 (Black Mic): present = No
>>>> Pin 0x1a (Black Line In): present = Yes
>>>> Pin 0x1b (Black HP Out): present = No
>>>> [julas at snowball2 ~]$ sudo python hda-jack-sense-test.py
>>>> Pin 0x18 (Black Mic): present = Yes
>>>> Pin 0x1a (Black Line In): present = No
>>>> Pin 0x1b (Black HP Out): present = No
>>>
>>>>>
>>>>>
>>>>> Is Node 0x17 also the side jack of your p150hm ?
>>>>> pin cap support Detect and Trigger but Misc = NO_PRESENCE
>>>>
>>>> Yes, it is between mic and line in jacks, third one from the front. The
>>>> only difference is that there is red light coming out of it.
>>>>
>>>
>>> you can use hda-verb to set the pin default of 0x17 and use
>>> hda-jack-sense-test retest the side jack
>>
>> Well, it kind of works:
>> * I was able to assign 0x01011013 to pin 0x17 using user_pin_configs
>> * it then shows up in hda-jack-sense-test.py, which detects if the jack
>> is connected
>> $ sudo python hda-jack-sense-test.py
>> [sudo] password for julas:
>> Pin 0x17 (Black Line Out): present = Yes
>> Pin 0x18 (Black Mic): present = No
>> Pin 0x1a (Black Line In): present = No
>> Pin 0x1b (Black HP Out): present = No
>> * for some reason this program started locking up after showing the
>> output, I am not sure if this is related.
>> I then applied your patch on top of Fedora 3.1.1 kernel (crude patch
>> attached). After reboot:
>> * hda-jack-sense-test.py was still working, without lockups this time
>> * alsamixer -c0 revealed a new "Front" slider, which was controlling the
>> volume on 0x17
>> * there was still no 8-channel mode (probably related to what you wrote
>> below)
>> * there were more options for auto mute (Disabled, Speaker Only, Line
>> Out+Speaker)
>> * here is the new alsa-info.sh:
>> http://www.alsa-project.org/db/?f=923b75ad3997dc8f5878852e327f9b999a196052
>>
>
> You can add the following code to assign dac and pin in alc_auto_fill_dac_nids()
>
> However this cannot create "Headphone Playback Volume" and "Speaker
> Playback Volume"
>
I am also not sure what you mean by HP and Speaker Playback Volumes - it
is working now, even with unpatched Fedora kernels (3.1.1-2.fc16).
With this patch applied on top of sound/master tree it is much worse:
* Front and HP sliders are gone
* only 2-ch sound is working, changing to 4, 6, or 8 does not produce
output on any of the other jacks
* just to be sure, I checked sound/master tree without both of your
patches, and both Headphone/Speaker, as well as 4 and 6 channel sound
are working fine.
>
> again:
> /* set num_dacs once to full for alc_auto_look_for_dac() */
> spec->multiout.num_dacs = cfg->line_outs;
> spec->multiout.hp_out_nid[0] = 0;
> spec->multiout.extra_out_nid[0] = 0;
> memset(spec->private_dac_nids, 0, sizeof(spec->private_dac_nids));
> spec->multiout.dac_nids = spec->private_dac_nids;
>
> +/*
> + may check bit 2 of SKU ID in alc_subsystem_id() to determine this is
> a laptop with 4 jacks
> + * 2 : 0 --> Desktop, 1 --> Laptop
> +*/
> + if (cfg->hp_outs == 1 && cfg->line_outs == 1 && cfg->speaker_outs >= 1) {
> + num_pins = 0;
> + spec->private_dac_nids[0] = alc_auto_look_for_dac(codec, cfg->hp_pins[0]);
> + spec->multi_io[num_pins].pin = cfg->hp_pins[0];
> + spec->multi_io[num_pins].dac = spec->private_dac_nids[0];
> + num_pins++;
> + defcfg = snd_hda_codec_get_pincfg(codec, cfg->hp_pins[0]);
> + location = get_defcfg_location(defcfg);
> + spec->multiout.num_dacs = 1;
> + num_pins = alc_auto_fill_multi_ios(codec, location, 0);
> + if (num_pins > 0) {
> + spec->multi_ios = num_pins;
> + spec->ext_channel_count = 2;
> + }
> + spec->private_dac_nids[3] = alc_auto_look_for_dac(codec,
> cfg->line_out_pins[0]);
> + spec->multi_io[num_pins].pin = cfg->line_out_pins[0];
> + spec->multi_io[num_pins].dac = spec->private_dac_nids[3];
> + spec->multi_ios++;
> + spec->multiout.max_channels = 2;
> + spec->multiout.num_dacs = 1;
> +/*
> + Still missing
> + 1) need to swap dac of hp with speaker to create speaker volume
> + 2) hda-jack of mic, line and side
> + 3) p170hm has 5.1 speakers
> +*/
> + spec->multiout.extra_out_nid[0] =
> + get_dac_if_single(codec, cfg->speaker_pins[0]);
> + return 0;
> + }
>
>
>>>
>>> To add the missing pin default of side jack 0x17
>>>
>>> ALC662_FIXUP_ASUS_MODE8,
>>> + ALC892_FIXUP_CLEVO_4ST_8CH,
>>> };
>>>
>>> static const struct alc_fixup alc662_fixups[] = {
>>>
>>>
>>> + [ALC892_FIXUP_CLEVO_4ST_8CH] = {
>>> + .type = ALC_FIXUP_PINS,
>>> + .v.pins = (const struct alc_pincfg[]) {
>>> +/*
>>> + need to be same location as the other jack
>>> + may need to change the default association and sequence since
>>> + Lower Default Association values would be higher in priority for resources
>>> + such as processing nodes or Input and Output Converters.
>>> + A value of 0000b is reserved and should not be used
>>> +*/
>>> + { 0x17, 0x01011013 }, /* Side */
>>> + { }
>>> + },
>>> + },
>>>
>>>
>>> + SND_PCI_QUIRK(0x1558, 0x5102, "Clevo P150HM", ALC892_FIXUP_CLEVO_4ST_8CH),
>>> + SND_PCI_QUIRK(0x1558, 0x7100, "Clevo P170HM", ALC892_FIXUP_CLEVO_4ST_8CH),
>>>
>>> SImilar case are those notebooks hda-emu/codecs/alc1200-msi-gx620
>>> which has 1 hp(green), 1 line-in(blue), 1 ext-mic(pink) and 1 line
>>> out(grey) at same location (ext rear) for surround71 (and also 1
>>> speakers, 1 int mic)
>>>
>>>
>>> hda_codec: ALC1200: BIOS auto-probing.
>>> hda_codec: ALC1200: SKU not ready 0x598301f0
>>> autoconfig: line_outs=1 (0x17/0x0/0x0/0x0/0x0) type:line
>>> speaker_outs=1 (0x1b/0x0/0x0/0x0/0x0)
>>> hp_outs=1 (0x14/0x0/0x0/0x0/0x0)
>>> mono: mono_out=0x0
>>> dig-out=0x1e/0x0
>>> inputs: Mic=0x18 Internal Mic=0x19 Line=0x1a
>>>
>>>
>>> CTRL: add: Line-Out Jack:0
>>> CTRL: add: Headphone Jack:0
>>> CTRL: add: Mic Jack:0
>>> CTRL: add: Line Jack:0
>>>
>>>> get 1
>>> 1 Channel Mode:0
>>> ITEM: 0:2ch, 1:4ch, 2:6ch, VAL: [2ch]
>>>
>>> what is missing are
>>> 1) 8ch in "Channel Mode" ,
>>> 2) Side Playback Volume
>>> 3)Side Playback Switch
>>>
>>> Study the logic to add 8ch and "side" in
>>>
>>> 1) alc_auto_fill_dac_nids()
>>> 2) alc_auto_fill_multi_ios() which add line-in and mic jack to multi_ios,
>>
>> I am sorry, I am afraid I lack the knowledge to do that. What I can do
>> is test patches and commands, but writing new code is beyond my skillset.
>>
>>>
>>>
>>> This mean that when switch to 6/8 channel mode, it will conflict with
>>> automic detection since the pin cap alc892 's mic jack does not
>>> support impedance sense and the driver does not know the plug is mic
>>> or speaker by measuring the impedance
>>>
>>> The driver have to disable automic detection when user switch "channel
>>> mode" to 6ch/8ch as the user should still able to use the internal mic
>>> when the external mic jack is retasked as output
>>>
>>>
>>>>>
>>>>> which node is your subwoofer ?
>>>>
>>>> This I have not figured out yet unfortunately. Keep in mind that in
>>>> windows you need THX TruStudio PRO to get it working, and the config is
>>>> advertised as stereo. There was a discussion about this on
>>>> notebookreview forums [1], so maybe it configured in some weird way?
>>>>
>>>
>>> you have to find out whether subwoofer is connected to 0x16 of your
>>> p150hm since your mic jack (retasked as clfe) is connected to dac 0x4.
>>
>> Simply changing this pin to out and unmuting it did not work (this is
>> the way I discovered 0x17.
>>
More information about the Alsa-devel
mailing list