[alsa-devel] ALSA error : frame 0 active: -75

[Rajul Kumar]

Hi ,

Thanx for your reply .

We are simply using audio class driver and linux usb host stack .
Can u let me know more regarding which capture buffer size to increase
we are doing usb audio streaming on usb host side .

Thanx & Regards
Rajul

On Fri, Nov 12, 2010 at 3:30 PM, Irfan Shaikh <irfan.shaikh at sasken.com> wrote:
> Increase the size of your Capture Buffer in capture device (USB audio class)
> I guess this would help you in solving the Overrun problem
> ________________________________________
> From: alsa-devel-bounces at alsa-project.org [alsa-devel-bounces at alsa-project.org] On Behalf Of Rajul Kumar [rajul.manit1 at gmail.com]
> Sent: Friday, November 12, 2010 2:32 PM
> To: Clemens Ladisch
> Cc: tiwai at suse.de; alsa-devel at alsa-project.org
> Subject: Re: [alsa-devel] ALSA error : frame 0 active: -75
>
> Hi ,
>
> Thanx for the reply .
> i have a few more queries . please find time to guide regarding these .
>
> 1)
> is it possible to have some software solution from audio class driver
> for  -EOVERFLOW condition ?
>
> 2)
> As depicted from error-codes.txt , -EOVERFLOW can be indicative of
> hardware problem also .
>
> Can we be suggested how we can make sure that problem lies in the hardware only
> ( i mean via some code in usb stack or anything else ) .
>
> 3)
>
> Are there some mandatory H/W requirements for   iso transfer usb signal
> which may not be  required for bulk or other transfers ,
> without which iso transfers can report H/W errors  anytime ?
>
> how can usb signal be improved so as to perfectly support iso transfers ?
>
>
> Thanx & Regards
> Rajul
>
>
>
>
> On Fri, Nov 12, 2010 at 2:16 PM, Clemens Ladisch <clemens at ladisch.de> wrote:
>> Rajul Kumar wrote:
>>> ALSA sound/usb/usbaudio.c:354: frame 0 active: -75
>>
>> -75 = -EOVERFLOW
>>
>>> which is followed by coninous loop of below messages :
>>>
>>> ALSA sound/usb/usbaudio.c:354: frame 0 active: -71
>>
>> -71 = -EPROTO
>>
>>> ALSA sound/usb/usbaudio.c:354: frame 0 active: -18
>>
>> -18 = -EXDEV
>>
>> Documentation/usb/error-codes.txt says:
>> | -EOVERFLOW (*)          The amount of data returned by the endpoint was
>> |                         greater than either the max packet size of the
>> |                         endpoint or the remaining buffer size.  "Babble".
>>
>> | -EPROTO (*, **)         a) bitstuff error
>> |                         b) no response packet received within the
>> |                            prescribed bus turn-around time
>> |                         c) unknown USB error
>>
>> | -EXDEV                  ISO transfer only partially completed
>> |                         look at individual frame status for details
>>
>> | (*) Error codes like -EPROTO, -EILSEQ and -EOVERFLOW normally indicate
>> | hardware problems such as bad devices (including firmware) or cables.
>>
>>
>> Regards,
>> Clemens
>>
> _______________________________________________
> Alsa-devel mailing list
> Alsa-devel at alsa-project.org
> http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
>
> SASKEN BUSINESS DISCLAIMER: This message may contain confidential, proprietary or legally privileged information. In case you are not the original intended Recipient of the message, you must not, directly or indirectly, use, disclose, distribute, print, or copy any part of this message and you are requested to delete it and inform the sender. Any views expressed in this message are those of the individual sender unless otherwise stated. Nothing contained in this message shall be construed as an offer or acceptance of any offer by Sasken Communication Technologies Limited ("Sasken") unless sent with that express intent and with due authority of Sasken. Sasken has taken enough precautions to prevent the spread of viruses. However the company accepts no liability for any damage caused by any virus transmitted by this email.
> Read Disclaimer at http://www.sasken.com/extras/mail_disclaimer.html
>