[alsa-devel] idt blue jack patch
Paulo Cavalcanti
promac at gmail.com
Fri Feb 20 17:07:03 CET 2009
On Fri, Feb 20, 2009 at 11:31 AM, Wu Fengguang <fengguang.wu at intel.com>wrote:
> On Fri, Feb 20, 2009 at 04:16:52PM +0200, Paulo Cavalcanti wrote:
> >
> >
> > On Fri, Feb 20, 2009 at 8:20 AM, Wu Fengguang <fengguang.wu at intel.com
> <mailto:fengguang.wu at intel.com>> wrote:
> > On Fri, Feb 20, 2009 at 12:15:16PM +0200, Paulo Cavalcanti wrote:
> > >
> > >
> > > On Thu, Feb 19, 2009 at 10:00 PM, Wu Fengguang <fengguang.wu at intel.com
> <mailto:fengguang.wu at intel.com><mailto:fengguang.wu at intel.com<mailto:
> fengguang.wu at intel.com>>> wrote:
> > > Hi Tobin,
> > >
> > > Here are the Linux and WinXP pin configurations.
> > > Both Linux and WinXP configure node 0x0c as an output pin.
> > >
> > > However the driver seems to be offering three schemes:
> > >
> > > scheme desc 0xC dev
> > > ------------------------------------------------------
> > > IDS_CONFIG_OPEN Speaker_Side/LineIn
> > > IDS_CONFIG_51 LineIn
> > > IDS_CONFIG_71 Speaker_Side
> > >
> > > Paulo, maybe you can run these commands to switch between
> > > linein/lineout modes:
> > >
> > > # wget
> http://www.kernel.org/pub/linux/kernel/people/tiwai/misc/hda-verb-0.3.tar.bz2
> > >
> > > # set PIN_IN mode
> > > hda-verb /dev/snd/hwC0D2 0x0c SET_PIN_WIDGET_CONTROL 0x20
> > >
> > > # set PIN_OUT mode
> > > hda-verb /dev/snd/hwC0D2 0x0c SET_PIN_WIDGET_CONTROL 0x40
> > >
> > > Thanks,
> > > Fengguang
> > > ---
> > >
> > > /proc/asound/card0/codec\#2
> > >
> > > Codec: IDT 92HD73E1X5
> > > Address: 2
> > > Vendor Id: 0x111d7676
> > > Subsystem Id: 0x80865002
> > > Revision Id: 0x100202
> > >
> > >
> > > AUD_allOS_6033.2_PV_IDTGUI_v124/WDM/WinXP/Sthda.ini
> > >
> > > # sthda.INI
> > > [Models]
> > > ...
> > > HDAUDIO\FUNC_01&VEN_111D&DEV_7676&SUBSYS_80865002=I73E-EL2.INI
> > > ...
> > >
> > >
> > > AUD_allOS_6033.2_PV_IDTGUI_v124/WDM/WinXP/I73E-EL2.INI
> > >
> > > [HKR\Settings\Pin\0C]
> > > CfgDflt = dword: 0x01113214
> > > AltCfg = hex: 5E,32,81,01
> > > AssignedDAC = hex: 0x18
> > >
> > >
> > > /proc/asound/card0/codec\#2
> > >
> > > Node 0x0c [Pin Complex] wcaps 0x400183: Stereo Amp-In
> > > Amp-In caps: N/A
> > > Amp-In vals: [0x00 0x00]
> > > Pincap 0x00001737: IN OUT Detect Trigger ImpSense
> > > Vref caps: HIZ 50 GRD 80
> > > Pin Default 0x01113014: [Jack] Speaker at Ext Rear
> > > Conn = 1/8, Color = Blue
> > > DefAssociation = 0x1, Sequence = 0x4
> > > Pin-ctls: 0x40: OUT VREF_HIZ
> > > Unsolicited: tag=04, enabled=1
> > > Connection: 6
> > > 0x15 0x16 0x17 0x18* 0x19 0x1e
> > >
> > >
> > > Thanks a lot, Fengguang.
> > >
> > > The other models for this codec are for Dell computers.
> > > Probably, all of then will behave the same way, right?
> >
> > I guess the hda-verb commands will work for all IN/OUT configurable pins.
> >
> > > I still have a question. I see that you changed Pin Default
> 0x01113014,
> > > for 0x01813021, in the driver for having LineIn.
> > > Also, Pin-ctls: 0x40 should provide the pin as an output. The Node is
> 0x0c.
> > >
> > > Therefore,
> > >
> > > # set PIN_OUT mode
> > > hda-verb /dev/snd/hwC0D2 0x0c SET_PIN_WIDGET_CONTROL 0x40
> > >
> > > makes sense.
> > >
> > > But how would I know that 0x20 would turn the pin 0x0c into LineIn?
> > >
> > > # set PIN_IN mode
> > > hda-verb /dev/snd/hwC0D2 0x0c SET_PIN_WIDGET_CONTROL 0x20
> >
> > ALSA defined the following values according to the HDA spec:
> >
> > /* Pin widget control - 8bit */
> > #define AC_PINCTL_IN_EN (1<<5)
> > #define AC_PINCTL_OUT_EN (1<<6)
> > #define AC_PINCTL_HP_EN (1<<7)
> >
> > #define PIN_IN (AC_PINCTL_IN_EN)
> > #define PIN_OUT (AC_PINCTL_OUT_EN)
> > #define PIN_HP (AC_PINCTL_OUT_EN |
> AC_PINCTL_HP_EN)
> >
> > So PIN_OUT=0x40 and PIN_IN=0x20.
> >
> > > I am asking because I have a Dell laptop (Vostro 1400) where the
> external mic
> > > works when I use model=ref (and I loose the speakers in this case), but
> not
> > > when I use model=dell-3stack. If I could figure out how to switch
> > > the pin using hda-verb in this case, would solve my problems when using
> skype.
> >
> > You can locate the external mic pin in /proc/asound/card0/codec#* and
> > feed its node id to the hda-verb command. It should work the same way.
> >
> > This is from model=ref. I can see it defines Line In as the
> > pin 0xe (exactly the jack marked as mic in the Vostro 1400).
> > This is how it should be.
> >
>
> But you pasted info for 0x0c instead of 0xe below...
> Would you provide the full codec file?
>
> > Node 0x0c [Pin Complex] wcaps 0x400181: Stereo
> > Pincap 0x00001737: IN OUT Detect Trigger ImpSense
> > Vref caps: HIZ 50 GRD 80
> > Pin Default 0x0181304e: [Jack] Line In at Ext Rear
> > Conn = 1/8, Color = Blue
> > DefAssociation = 0x4, Sequence = 0xe
> > Pin-ctls: 0x20: IN VREF_HIZ
> > Unsolicited: tag=04, enabled=1
> > Connection: 1
> > 0x03
> >
> > ----------------------------------
> >
> > This is from model=dell-3stack. There is no Line In defined. This
> > is the problem....
> >
> >
> > Node 0x10 [Pin Complex] wcaps 0x400181: Stereo
> > Pincap 0x00000037: IN OUT Detect Trigger ImpSense
> > Pin Default 0x01813050: [Jack] Line In at Ext Rear
> > Conn = 1/8, Color = Blue
> > DefAssociation = 0x5, Sequence = 0x0
> > Pin-ctls: 0x20: IN
> > Unsolicited: tag=04, enabled=1
> > Connection: 1
> > 0x04
> >
> >
> > The question is: how can I use hda-verb to make pin 0xe
> > be an input pin (0x20), the way it were when using model = ref?
>
> Where is Node 0x0e? You didn't paste Node 0x0e info, but 0x0c and 0x10.
>
> > set PIN_IN mode:
> > hda-verb /dev/snd/hwC0D0 0x0c SET_PIN_WIDGET_CONTROL 0x20
> >
> > The node is 0x0c, but I am not sure if it is that simple.
>
> It's trivial to try it out, its harmless anyway :)
> You only have to replace 0x0c with your mic node.
>
>
Using hda-verb-0.3, the pins are:
0xa - headphones (first connector - the one which works)
0xf - headphones (second connector - no output)
0xe - analog mic
I am attaching the dell-3stack codec and the ref codec.
This laptop has a digital Mic and a jack for connecting an analog
mic, ehich I am supposing it is the "Line In" in the "model=ref" codec.
The dell-3tack model works well, but I have no analog mic, and the
digital mic sounds too low to be usable.
If you could give me a hand with this matter, I would
be very grateful.
Thanks.
--
Paulo Roma Cavalcanti
LCG - UFRJ
-------------- next part --------------
Codec: SigmaTel STAC9228
Address: 0
Vendor Id: 0x83847616
Subsystem Id: 0x10280227
Revision Id: 0x100201
No Modem Function Group found
Default PCM:
rates [0x7e0]: 44100 48000 88200 96000 176400 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Default Amp-In caps: ofs=0x00, nsteps=0x0e, stepsize=0x05, mute=0
Default Amp-Out caps: ofs=0x7f, nsteps=0x7f, stepsize=0x02, mute=1
GPIO: io=3, o=0, i=0, unsolicited=1, wake=1
IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[2]: enable=1, dir=1, wake=0, sticky=0, data=1, unsol=0
Analog Loopback: 0x00
Node 0x02 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out R/L
Amp-Out caps: N/A
Amp-Out vals: [0x5b 0x5b]
Converter: stream=5, channel=0
Power: setting=D0, actual=D0
Delay: 13 samples
Node 0x03 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out R/L
Amp-Out caps: N/A
Amp-Out vals: [0xdc 0xdc]
Converter: stream=5, channel=0
Power: setting=D0, actual=D0
Delay: 13 samples
Node 0x04 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out R/L
Amp-Out caps: N/A
Amp-Out vals: [0xdc 0xdc]
Converter: stream=5, channel=0
Power: setting=D0, actual=D0
Delay: 13 samples
Node 0x05 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out R/L
Amp-Out caps: N/A
Amp-Out vals: [0xdc 0xdc]
Converter: stream=5, channel=0
Power: setting=D0, actual=D0
Delay: 13 samples
Node 0x06 [Vendor Defined Widget] wcaps 0xfd0c05: Stereo Amp-Out R/L
Amp-Out caps: N/A
Amp-Out vals: [0xff 0xff]
Power: setting=D3, actual=D3
Delay: 13 samples
Node 0x07 [Audio Input] wcaps 0x1d0541: Stereo
Converter: stream=1, channel=0
SDI-Select: 0
Power: setting=D0, actual=D0
Delay: 13 samples
Connection: 1
0x1b
Processing caps: benign=0, ncoeff=0
Node 0x08 [Audio Input] wcaps 0x1d0541: Stereo
Converter: stream=0, channel=0
SDI-Select: 0
Power: setting=D0, actual=D0
Delay: 13 samples
Connection: 1
0x1c
Processing caps: benign=0, ncoeff=0
Node 0x09 [Audio Input] wcaps 0x1d0541: Stereo
Converter: stream=0, channel=0
SDI-Select: 0
Power: setting=D0, actual=D0
Delay: 13 samples
Connection: 1
0x1d
Processing caps: benign=0, ncoeff=0
Node 0x0a [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0000173f: IN OUT HP Detect Trigger ImpSense
Vref caps: HIZ 50 GRD 80
Pin Default 0x02211230: [Jack] HP Out at Ext Front
Conn = 1/8, Color = Black
DefAssociation = 0x3, Sequence = 0x0
Pin-ctls: 0x00: VREF_HIZ
Unsolicited: tag=01, enabled=1
Connection: 2
0x02* 0x03
Node 0x0b [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0000173f: IN OUT HP Detect Trigger ImpSense
Vref caps: HIZ 50 GRD 80
Pin Default 0x02a11220: [Jack] Mic at Ext Front
Conn = 1/8, Color = Black
DefAssociation = 0x2, Sequence = 0x0
Pin-ctls: 0x24: IN VREF_80
Unsolicited: tag=03, enabled=1
Connection: 2
0x02 0x03*
Node 0x0c [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x00001737: IN OUT Detect Trigger ImpSense
Vref caps: HIZ 50 GRD 80
Pin Default 0x01a19040: [Jack] Mic at Ext Rear
Conn = 1/8, Color = Pink
DefAssociation = 0x4, Sequence = 0x0
Pin-ctls: 0x24: IN VREF_80
Unsolicited: tag=02, enabled=1
Connection: 1
0x03
Node 0x0d [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0000173f: IN OUT HP Detect Trigger ImpSense
Vref caps: HIZ 50 GRD 80
Pin Default 0x01114210: [Jack] Speaker at Ext Rear
Conn = 1/8, Color = Green
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x40: OUT VREF_HIZ
Unsolicited: tag=00, enabled=0
Connection: 1
0x02
Node 0x0e [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x00001737: IN OUT Detect Trigger ImpSense
Vref caps: HIZ 50 GRD 80
Pin Default 0x01111212: [Jack] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0x1, Sequence = 0x2
Pin-ctls: 0x40: OUT VREF_HIZ
Unsolicited: tag=00, enabled=0
Connection: 1
0x04
Node 0x0f [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x00001737: IN OUT Detect Trigger ImpSense
Vref caps: HIZ 50 GRD 80
Pin Default 0x01116211: [Jack] Speaker at Ext Rear
Conn = 1/8, Color = Orange
DefAssociation = 0x1, Sequence = 0x1
Pin-ctls: 0x40: OUT VREF_HIZ
Unsolicited: tag=00, enabled=0
Connection: 1
0x05
Node 0x10 [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x00000037: IN OUT Detect Trigger ImpSense
Pin Default 0x01813050: [Jack] Line In at Ext Rear
Conn = 1/8, Color = Blue
DefAssociation = 0x5, Sequence = 0x0
Pin-ctls: 0x20: IN
Unsolicited: tag=04, enabled=1
Connection: 1
0x04
Node 0x11 [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x00000037: IN OUT Detect Trigger ImpSense
Pin Default 0x01112214: [Jack] Speaker at Ext Rear
Conn = 1/8, Color = Grey
DefAssociation = 0x1, Sequence = 0x4
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Connection: 1
0x03
Node 0x12 [Pin Complex] wcaps 0x400001: Stereo
Pincap 0x00000020: IN
Pin Default 0x403003fa: [N/A] CD at Ext N/A
Conn = Unknown, Color = Unknown
DefAssociation = 0xf, Sequence = 0xa
Misc = NO_PRESENCE
Pin-ctls: 0x00:
Node 0x13 [Pin Complex] wcaps 0x400001: Stereo
Pincap 0x00000020: IN
Pin Default 0x90a60040: [Fixed] Mic at Int N/A
Conn = Digital, Color = Unknown
DefAssociation = 0x4, Sequence = 0x0
Pin-ctls: 0x20: IN
Node 0x14 [Pin Complex] wcaps 0x400001: Stereo
Pincap 0x00000020: IN
Pin Default 0x90a60040: [Fixed] Mic at Int N/A
Conn = Digital, Color = Unknown
DefAssociation = 0x4, Sequence = 0x0
Pin-ctls: 0x20: IN
Node 0x15 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0
Amp-Out vals: [0x04 0x04]
Connection: 9
0x0e 0x12 0x0f 0x0b 0x0c* 0x0d 0x0a 0x10 0x11
Node 0x16 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0
Amp-Out vals: [0x00 0x00]
Connection: 9
0x0e 0x12 0x0f 0x0b 0x0c* 0x0d 0x0a 0x10 0x11
Node 0x17 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0
Amp-Out vals: [0x00 0x00]
Connection: 9
0x0e 0x12 0x0f 0x0b 0x0c* 0x0d 0x0a 0x10 0x11
Node 0x18 [Audio Selector] wcaps 0x300103: Stereo Amp-In
Amp-In caps: N/A
Amp-In vals: [0x06 0x06]
Connection: 1
0x15
Node 0x19 [Audio Selector] wcaps 0x300103: Stereo Amp-In
Amp-In caps: N/A
Amp-In vals: [0x00 0x00]
Connection: 1
0x16
Node 0x1a [Audio Selector] wcaps 0x300103: Stereo Amp-In
Amp-In caps: N/A
Amp-In vals: [0x00 0x00]
Connection: 1
0x17
Node 0x1b [Audio Selector] wcaps 0x30090d: Stereo Amp-Out R/L
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Connection: 3
0x18 0x13* 0x14
Node 0x1c [Audio Selector] wcaps 0x30090d: Stereo Amp-Out R/L
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Connection: 3
0x19* 0x13 0x14
Node 0x1d [Audio Selector] wcaps 0x30090d: Stereo Amp-Out R/L
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Connection: 3
0x1a* 0x13 0x14
Node 0x1e [Audio Output] wcaps 0x40211: Stereo Digital
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:
rates [0x7e0]: 44100 48000 88200 96000 176400 192000
bits [0xe]: 16 20 24
formats [0x5]: PCM AC3
Delay: 4 samples
Node 0x1f [Vendor Defined Widget] wcaps 0xf30201: Stereo Digital
Delay: 3 samples
Node 0x20 [Audio Input] wcaps 0x140311: Stereo Digital
Converter: stream=0, channel=0
SDI-Select: 0
Digital:
Digital category: 0x0
PCM:
rates [0x160]: 44100 48000 96000
bits [0xe]: 16 20 24
formats [0x5]: PCM AC3
Delay: 4 samples
Connection: 1
0x22
Node 0x21 [Pin Complex] wcaps 0x400301: Stereo Digital
Pincap 0x00000010: OUT
Pin Default 0x404003fb: [N/A] SPDIF Out at Ext N/A
Conn = Unknown, Color = Unknown
DefAssociation = 0xf, Sequence = 0xb
Misc = NO_PRESENCE
Pin-ctls: 0x00:
Connection: 5
0x1e* 0x1f 0x1b 0x1c 0x1d
Node 0x22 [Pin Complex] wcaps 0x430681: Stereo Digital
Pincap 0x00010024: IN EAPD Detect
EAPD 0x0:
Pin Default 0x40c003fc: [N/A] SPDIF In at Ext N/A
Conn = Unknown, Color = Unknown
DefAssociation = 0xf, Sequence = 0xc
Misc = NO_PRESENCE
Pin-ctls: 0x00:
Unsolicited: tag=00, enabled=0
Power: setting=D0, actual=D0
Delay: 3 samples
Node 0x23 [Beep Generator Widget] wcaps 0x70000c: Mono Amp-Out
Amp-Out caps: ofs=0x03, nsteps=0x03, stepsize=0x17, mute=0
Amp-Out vals: [0x00]
Node 0x24 [Volume Knob Widget] wcaps 0x600000: Mono
Volume-Knob: delta=1, steps=127, direct=1, val=127
Connection: 4
0x02* 0x03 0x04 0x05
-------------- next part --------------
Codec: SigmaTel STAC9228
Address: 0
Vendor Id: 0x83847616
Subsystem Id: 0x10280227
Revision Id: 0x100201
No Modem Function Group found
Default PCM:
rates [0x7e0]: 44100 48000 88200 96000 176400 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Default Amp-In caps: ofs=0x00, nsteps=0x0e, stepsize=0x05, mute=0
Default Amp-Out caps: ofs=0x7f, nsteps=0x7f, stepsize=0x02, mute=1
GPIO: io=3, o=0, i=0, unsolicited=1, wake=1
IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[2]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
Analog Loopback: 0x00
Node 0x02 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out R/L
Amp-Out caps: N/A
Amp-Out vals: [0x49 0x49]
Converter: stream=0, channel=0
Power: setting=D0, actual=D0
Delay: 13 samples
Node 0x03 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out R/L
Amp-Out caps: N/A
Amp-Out vals: [0xe4 0xe4]
Converter: stream=0, channel=0
Power: setting=D0, actual=D0
Delay: 13 samples
Node 0x04 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out R/L
Amp-Out caps: N/A
Amp-Out vals: [0xe4 0xe4]
Converter: stream=0, channel=0
Power: setting=D0, actual=D0
Delay: 13 samples
Node 0x05 [Audio Output] wcaps 0xd0c05: Stereo Amp-Out R/L
Amp-Out caps: N/A
Amp-Out vals: [0xe4 0xe4]
Converter: stream=0, channel=0
Power: setting=D0, actual=D0
Delay: 13 samples
Node 0x06 [Vendor Defined Widget] wcaps 0xfd0c05: Stereo Amp-Out R/L
Amp-Out caps: N/A
Amp-Out vals: [0xff 0xff]
Power: setting=D3, actual=D3
Delay: 13 samples
Node 0x07 [Audio Input] wcaps 0x1d0541: Stereo
Converter: stream=0, channel=0
SDI-Select: 0
Power: setting=D0, actual=D0
Delay: 13 samples
Connection: 1
0x1b
Processing caps: benign=0, ncoeff=0
Node 0x08 [Audio Input] wcaps 0x1d0541: Stereo
Converter: stream=0, channel=0
SDI-Select: 0
Power: setting=D0, actual=D0
Delay: 13 samples
Connection: 1
0x1c
Processing caps: benign=0, ncoeff=0
Node 0x09 [Audio Input] wcaps 0x1d0541: Stereo
Converter: stream=0, channel=0
SDI-Select: 0
Power: setting=D0, actual=D0
Delay: 13 samples
Connection: 1
0x1d
Processing caps: benign=0, ncoeff=0
Node 0x0a [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0000173f: IN OUT HP Detect Trigger ImpSense
Vref caps: HIZ 50 GRD 80
Pin Default 0x02214020: [Jack] HP Out at Ext Front
Conn = 1/8, Color = Green
DefAssociation = 0x2, Sequence = 0x0
Pin-ctls: 0x00: VREF_HIZ
Unsolicited: tag=01, enabled=1
Connection: 2
0x02* 0x03
Node 0x0b [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0000173f: IN OUT HP Detect Trigger ImpSense
Vref caps: HIZ 50 GRD 80
Pin Default 0x02a19080: [Jack] Mic at Ext Front
Conn = 1/8, Color = Pink
DefAssociation = 0x8, Sequence = 0x0
Pin-ctls: 0x24: IN VREF_80
Unsolicited: tag=03, enabled=1
Connection: 2
0x02* 0x03
Node 0x0c [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x00001737: IN OUT Detect Trigger ImpSense
Vref caps: HIZ 50 GRD 80
Pin Default 0x0181304e: [Jack] Line In at Ext Rear
Conn = 1/8, Color = Blue
DefAssociation = 0x4, Sequence = 0xe
Pin-ctls: 0x20: IN VREF_HIZ
Unsolicited: tag=04, enabled=1
Connection: 1
0x03
Node 0x0d [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x0000173f: IN OUT HP Detect Trigger ImpSense
Vref caps: HIZ 50 GRD 80
Pin Default 0x01014010: [Jack] Line Out at Ext Rear
Conn = 1/8, Color = Green
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x40: OUT VREF_HIZ
Unsolicited: tag=00, enabled=0
Connection: 1
0x02
Node 0x0e [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x00001737: IN OUT Detect Trigger ImpSense
Vref caps: HIZ 50 GRD 80
Pin Default 0x01a19040: [Jack] Mic at Ext Rear
Conn = 1/8, Color = Pink
DefAssociation = 0x4, Sequence = 0x0
Pin-ctls: 0x24: IN VREF_80
Unsolicited: tag=02, enabled=1
Connection: 1
0x04
Node 0x0f [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x00001737: IN OUT Detect Trigger ImpSense
Vref caps: HIZ 50 GRD 80
Pin Default 0x01011012: [Jack] Line Out at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0x1, Sequence = 0x2
Pin-ctls: 0x40: OUT VREF_HIZ
Unsolicited: tag=00, enabled=0
Connection: 1
0x05
Node 0x10 [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x00000037: IN OUT Detect Trigger ImpSense
Pin Default 0x01016011: [Jack] Line Out at Ext Rear
Conn = 1/8, Color = Orange
DefAssociation = 0x1, Sequence = 0x1
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Connection: 1
0x04
Node 0x11 [Pin Complex] wcaps 0x400181: Stereo
Pincap 0x00000037: IN OUT Detect Trigger ImpSense
Pin Default 0x0101201f: [Jack] Line Out at Ext Rear
Conn = 1/8, Color = Grey
DefAssociation = 0x1, Sequence = 0xf
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Connection: 1
0x03
Node 0x12 [Pin Complex] wcaps 0x400001: Stereo
Pincap 0x00000020: IN
Pin Default 0x183301f0: [Jack] CD at Int HDMI
Conn = ATAPI, Color = Unknown
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Node 0x13 [Pin Complex] wcaps 0x400001: Stereo
Pincap 0x00000020: IN
Pin Default 0x18a001f0: [Jack] Mic at Int HDMI
Conn = Unknown, Color = Unknown
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x00:
Node 0x14 [Pin Complex] wcaps 0x400001: Stereo
Pincap 0x00000020: IN
Pin Default 0x18a001f0: [Jack] Mic at Int HDMI
Conn = Unknown, Color = Unknown
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x00:
Node 0x15 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0
Amp-Out vals: [0x00 0x00]
Connection: 9
0x0e* 0x12 0x0f 0x0b 0x0c 0x0d 0x0a 0x10 0x11
Node 0x16 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0
Amp-Out vals: [0x00 0x00]
Connection: 9
0x0e* 0x12 0x0f 0x0b 0x0c 0x0d 0x0a 0x10 0x11
Node 0x17 [Audio Selector] wcaps 0x30010d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0
Amp-Out vals: [0x00 0x00]
Connection: 9
0x0e* 0x12 0x0f 0x0b 0x0c 0x0d 0x0a 0x10 0x11
Node 0x18 [Audio Selector] wcaps 0x300103: Stereo Amp-In
Amp-In caps: N/A
Amp-In vals: [0x0d 0x0d]
Connection: 1
0x15
Node 0x19 [Audio Selector] wcaps 0x300103: Stereo Amp-In
Amp-In caps: N/A
Amp-In vals: [0x00 0x00]
Connection: 1
0x16
Node 0x1a [Audio Selector] wcaps 0x300103: Stereo Amp-In
Amp-In caps: N/A
Amp-In vals: [0x00 0x00]
Connection: 1
0x17
Node 0x1b [Audio Selector] wcaps 0x30090d: Stereo Amp-Out R/L
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Connection: 3
0x18* 0x13 0x14
Node 0x1c [Audio Selector] wcaps 0x30090d: Stereo Amp-Out R/L
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Connection: 3
0x19* 0x13 0x14
Node 0x1d [Audio Selector] wcaps 0x30090d: Stereo Amp-Out R/L
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Connection: 3
0x1a* 0x13 0x14
Node 0x1e [Audio Output] wcaps 0x40211: Stereo Digital
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
PCM:
rates [0x7e0]: 44100 48000 88200 96000 176400 192000
bits [0xe]: 16 20 24
formats [0x5]: PCM AC3
Delay: 4 samples
Node 0x1f [Vendor Defined Widget] wcaps 0xf30201: Stereo Digital
Delay: 3 samples
Node 0x20 [Audio Input] wcaps 0x140311: Stereo Digital
Converter: stream=0, channel=0
SDI-Select: 0
Digital:
Digital category: 0x0
PCM:
rates [0x160]: 44100 48000 96000
bits [0xe]: 16 20 24
formats [0x5]: PCM AC3
Delay: 4 samples
Connection: 1
0x22
Node 0x21 [Pin Complex] wcaps 0x400301: Stereo Digital
Pincap 0x00000010: OUT
Pin Default 0x01442070: [Jack] SPDIF Out at Ext Rear
Conn = RCA, Color = Grey
DefAssociation = 0x7, Sequence = 0x0
Pin-ctls: 0x40: OUT
Connection: 5
0x1e* 0x1f 0x1b 0x1c 0x1d
Node 0x22 [Pin Complex] wcaps 0x430681: Stereo Digital
Pincap 0x00010024: IN EAPD Detect
EAPD 0x0:
Pin Default 0x01c42190: [Jack] SPDIF In at Ext Rear
Conn = RCA, Color = Grey
DefAssociation = 0x9, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=00, enabled=0
Power: setting=D0, actual=D0
Delay: 3 samples
Node 0x23 [Beep Generator Widget] wcaps 0x70000c: Mono Amp-Out
Amp-Out caps: ofs=0x03, nsteps=0x03, stepsize=0x17, mute=0
Amp-Out vals: [0x00]
Node 0x24 [Volume Knob Widget] wcaps 0x600000: Mono
Volume-Knob: delta=1, steps=127, direct=1, val=127
Connection: 4
0x02* 0x03 0x04 0x05
More information about the Alsa-devel
mailing list