[alsa-devel] [RFC PATCH 5/5] ASoC: simplify the SSP DMA parameters settings by run-time generation
pHilipp Zabel
philipp.zabel at gmail.com
Thu Apr 23 10:53:58 CEST 2009
On Thu, Apr 23, 2009 at 7:08 AM, Eric Miao <eric.y.miao at gmail.com> wrote:
> The SSP DMA parameters can actually be easily generated at run-time since
> they are almost similar except for the FIFO width and direction. Another
> benefit is the re-use of information from 'struct ssp_device', like SSDR
> physical FIFO address and DRCMR register index for both directions.
Yes, that does look a lot better.
> Signed-off-by: Eric Miao <eric.miao at marvell.com>
> ---
> sound/soc/pxa/pxa-ssp.c | 206 ++++++++++-------------------------------------
> 1 files changed, 43 insertions(+), 163 deletions(-)
>
> diff --git a/sound/soc/pxa/pxa-ssp.c b/sound/soc/pxa/pxa-ssp.c
> index 2ce4fb6..fb7235b 100644
> --- a/sound/soc/pxa/pxa-ssp.c
> +++ b/sound/soc/pxa/pxa-ssp.c
> @@ -50,139 +50,6 @@ struct ssp_priv {
> #endif
> };
>
> -#define PXA2xx_SSP1_BASE 0x41000000
> -#define PXA27x_SSP2_BASE 0x41700000
> -#define PXA27x_SSP3_BASE 0x41900000
> -#define PXA3xx_SSP4_BASE 0x41a00000
> -
> -static struct pxa2xx_pcm_dma_params pxa_ssp1_pcm_mono_out = {
> - .name = "SSP1 PCM Mono out",
> - .dev_addr = PXA2xx_SSP1_BASE + SSDR,
> - .drcmr = &DRCMR(14),
> - .dcmd = DCMD_INCSRCADDR | DCMD_FLOWTRG |
> - DCMD_BURST16 | DCMD_WIDTH2,
> -};
> -
> -static struct pxa2xx_pcm_dma_params pxa_ssp1_pcm_mono_in = {
> - .name = "SSP1 PCM Mono in",
> - .dev_addr = PXA2xx_SSP1_BASE + SSDR,
> - .drcmr = &DRCMR(13),
> - .dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC |
> - DCMD_BURST16 | DCMD_WIDTH2,
> -};
> -
> -static struct pxa2xx_pcm_dma_params pxa_ssp1_pcm_stereo_out = {
> - .name = "SSP1 PCM Stereo out",
> - .dev_addr = PXA2xx_SSP1_BASE + SSDR,
> - .drcmr = &DRCMR(14),
> - .dcmd = DCMD_INCSRCADDR | DCMD_FLOWTRG |
> - DCMD_BURST16 | DCMD_WIDTH4,
> -};
> -
> -static struct pxa2xx_pcm_dma_params pxa_ssp1_pcm_stereo_in = {
> - .name = "SSP1 PCM Stereo in",
> - .dev_addr = PXA2xx_SSP1_BASE + SSDR,
> - .drcmr = &DRCMR(13),
> - .dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC |
> - DCMD_BURST16 | DCMD_WIDTH4,
> -};
> -
> -static struct pxa2xx_pcm_dma_params pxa_ssp2_pcm_mono_out = {
> - .name = "SSP2 PCM Mono out",
> - .dev_addr = PXA27x_SSP2_BASE + SSDR,
> - .drcmr = &DRCMR(16),
> - .dcmd = DCMD_INCSRCADDR | DCMD_FLOWTRG |
> - DCMD_BURST16 | DCMD_WIDTH2,
> -};
> -
> -static struct pxa2xx_pcm_dma_params pxa_ssp2_pcm_mono_in = {
> - .name = "SSP2 PCM Mono in",
> - .dev_addr = PXA27x_SSP2_BASE + SSDR,
> - .drcmr = &DRCMR(15),
> - .dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC |
> - DCMD_BURST16 | DCMD_WIDTH2,
> -};
> -
> -static struct pxa2xx_pcm_dma_params pxa_ssp2_pcm_stereo_out = {
> - .name = "SSP2 PCM Stereo out",
> - .dev_addr = PXA27x_SSP2_BASE + SSDR,
> - .drcmr = &DRCMR(16),
> - .dcmd = DCMD_INCSRCADDR | DCMD_FLOWTRG |
> - DCMD_BURST16 | DCMD_WIDTH4,
> -};
> -
> -static struct pxa2xx_pcm_dma_params pxa_ssp2_pcm_stereo_in = {
> - .name = "SSP2 PCM Stereo in",
> - .dev_addr = PXA27x_SSP2_BASE + SSDR,
> - .drcmr = &DRCMR(15),
> - .dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC |
> - DCMD_BURST16 | DCMD_WIDTH4,
> -};
> -
> -static struct pxa2xx_pcm_dma_params pxa_ssp3_pcm_mono_out = {
> - .name = "SSP3 PCM Mono out",
> - .dev_addr = PXA27x_SSP3_BASE + SSDR,
> - .drcmr = &DRCMR(67),
> - .dcmd = DCMD_INCSRCADDR | DCMD_FLOWTRG |
> - DCMD_BURST16 | DCMD_WIDTH2,
> -};
> -
> -static struct pxa2xx_pcm_dma_params pxa_ssp3_pcm_mono_in = {
> - .name = "SSP3 PCM Mono in",
> - .dev_addr = PXA27x_SSP3_BASE + SSDR,
> - .drcmr = &DRCMR(66),
> - .dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC |
> - DCMD_BURST16 | DCMD_WIDTH2,
> -};
> -
> -static struct pxa2xx_pcm_dma_params pxa_ssp3_pcm_stereo_out = {
> - .name = "SSP3 PCM Stereo out",
> - .dev_addr = PXA27x_SSP3_BASE + SSDR,
> - .drcmr = &DRCMR(67),
> - .dcmd = DCMD_INCSRCADDR | DCMD_FLOWTRG |
> - DCMD_BURST16 | DCMD_WIDTH4,
> -};
> -
> -static struct pxa2xx_pcm_dma_params pxa_ssp3_pcm_stereo_in = {
> - .name = "SSP3 PCM Stereo in",
> - .dev_addr = PXA27x_SSP3_BASE + SSDR,
> - .drcmr = &DRCMR(66),
> - .dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC |
> - DCMD_BURST16 | DCMD_WIDTH4,
> -};
> -
> -static struct pxa2xx_pcm_dma_params pxa_ssp4_pcm_mono_out = {
> - .name = "SSP4 PCM Mono out",
> - .dev_addr = PXA3xx_SSP4_BASE + SSDR,
> - .drcmr = &DRCMR(67),
> - .dcmd = DCMD_INCSRCADDR | DCMD_FLOWTRG |
> - DCMD_BURST16 | DCMD_WIDTH2,
> -};
> -
> -static struct pxa2xx_pcm_dma_params pxa_ssp4_pcm_mono_in = {
> - .name = "SSP4 PCM Mono in",
> - .dev_addr = PXA3xx_SSP4_BASE + SSDR,
> - .drcmr = &DRCMR(66),
> - .dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC |
> - DCMD_BURST16 | DCMD_WIDTH2,
> -};
> -
> -static struct pxa2xx_pcm_dma_params pxa_ssp4_pcm_stereo_out = {
> - .name = "SSP4 PCM Stereo out",
> - .dev_addr = PXA3xx_SSP4_BASE + SSDR,
> - .drcmr = &DRCMR(67),
> - .dcmd = DCMD_INCSRCADDR | DCMD_FLOWTRG |
> - DCMD_BURST16 | DCMD_WIDTH4,
> -};
> -
> -static struct pxa2xx_pcm_dma_params pxa_ssp4_pcm_stereo_in = {
> - .name = "SSP4 PCM Stereo in",
> - .dev_addr = PXA3xx_SSP4_BASE + SSDR,
> - .drcmr = &DRCMR(66),
> - .dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC |
> - DCMD_BURST16 | DCMD_WIDTH4,
> -};
> -
> static void dump_registers(struct ssp_device *ssp)
> {
> dev_dbg(&ssp->pdev->dev, "SSCR0 0x%08x SSCR1 0x%08x SSTO 0x%08x\n",
> @@ -194,25 +61,33 @@ static void dump_registers(struct ssp_device *ssp)
> ssp_read_reg(ssp, SSACD));
> }
>
> -static struct pxa2xx_pcm_dma_params *ssp_dma_params[4][4] = {
> - {
> - &pxa_ssp1_pcm_mono_out, &pxa_ssp1_pcm_mono_in,
> - &pxa_ssp1_pcm_stereo_out, &pxa_ssp1_pcm_stereo_in,
> - },
> - {
> - &pxa_ssp2_pcm_mono_out, &pxa_ssp2_pcm_mono_in,
> - &pxa_ssp2_pcm_stereo_out, &pxa_ssp2_pcm_stereo_in,
> - },
> - {
> - &pxa_ssp3_pcm_mono_out, &pxa_ssp3_pcm_mono_in,
> - &pxa_ssp3_pcm_stereo_out, &pxa_ssp3_pcm_stereo_in,
> - },
> - {
> - &pxa_ssp4_pcm_mono_out, &pxa_ssp4_pcm_mono_in,
> - &pxa_ssp4_pcm_stereo_out, &pxa_ssp4_pcm_stereo_in,
> - },
> +struct pxa2xx_pcm_dma_data {
> + struct pxa2xx_pcm_dma_params params;
> + char name[20];
> };
>
> +static struct pxa2xx_pcm_dma_params *
> +ssp_get_dma_params(struct ssp_device *ssp, int stereo, int out)
> +{
> + struct pxa2xx_pcm_dma_data *dma;
> +
> + dma = kzalloc(sizeof(struct pxa2xx_pcm_dma_data), GFP_KERNEL);
> + if (dma == NULL)
> + return NULL;
> +
> + snprintf(dma->name, 20, "SSP%d PCM %s %s", ssp->port_id,
> + stereo ? "Stereo" : "Mono", out ? "out" : "in");
Should we change Stereo/Mono to 32-bit/16-bit here?
> +
> + dma->params.name = dma->name;
> + dma->params.drcmr = &DRCMR(out ? ssp->drcmr_tx : ssp->drcmr_rx);
> + dma->params.dcmd = (out ? (DCMD_INCSRCADDR | DCMD_FLOWTRG) :
> + (DCMD_INCTRGADDR | DCMD_FLOWSRC)) |
> + (stereo ? DCMD_WIDTH4 : DCMD_WIDTH2) | DCMD_BURST16;
> + dma->params.dev_addr = ssp->phys_base + SSDR;
> +
> + return &dma->params;
> +}
> +
> static int pxa_ssp_startup(struct snd_pcm_substream *substream,
> struct snd_soc_dai *dai)
> {
> @@ -225,6 +100,11 @@ static int pxa_ssp_startup(struct
> snd_pcm_substream *substream,
> clk_enable(priv->ssp->clk);
> ssp_disable(priv->ssp);
> }
> +
> + if (cpu_dai->dma_data) {
> + kfree(cpu_dai->dma_data);
> + cpu_dai->dma_data = NULL;
> + }
> return ret;
> }
>
> @@ -239,6 +119,11 @@ static void pxa_ssp_shutdown(struct
> snd_pcm_substream *substream,
> ssp_disable(priv->ssp);
> clk_disable(priv->ssp->clk);
> }
> +
> + if (cpu_dai->dma_data) {
> + kfree(cpu_dai->dma_data);
> + cpu_dai->dma_data = NULL;
> + }
> }
>
> #ifdef CONFIG_PM
> @@ -611,25 +496,20 @@ static int pxa_ssp_hw_params(struct
> snd_pcm_substream *substream,
> struct snd_soc_dai *cpu_dai = rtd->dai->cpu_dai;
> struct ssp_priv *priv = cpu_dai->private_data;
> struct ssp_device *ssp = priv->ssp;
> - int dma = 0, chn = params_channels(params);
> + int chn = params_channels(params);
> u32 sscr0;
> u32 sspsp;
> int width = snd_pcm_format_physical_width(params_format(params));
> int ttsa = ssp_read_reg(ssp, SSTSA) & 0xf;
>
> - /* select correct DMA params */
> - if (substream->stream != SNDRV_PCM_STREAM_PLAYBACK)
> - dma = 1; /* capture DMA offset is 1,3 */
> - /* Network mode with one active slot (ttsa == 1) can be used
> - * to force 16-bit frame width on the wire (for S16_LE), even
> - * with two channels. Use 16-bit DMA transfers for this case.
> - */
Do you think the ttsa bit below is obvious enough to warrant removal
of the above comment?
> - if (((chn == 2) && (ttsa != 1)) || (width == 32))
> - dma += 2; /* 32-bit DMA offset is 2, 16-bit is 0 */
> -
> - cpu_dai->dma_data = ssp_dma_params[cpu_dai->id][dma];
> + printk("%s\n", __func__);
> + /* generate correct DMA params */
> + if (cpu_dai->dma_data)
> + kfree(cpu_dai->dma_data);
>
> - dev_dbg(&ssp->pdev->dev, "pxa_ssp_hw_params: dma %d\n", dma);
> + cpu_dai->dma_data = ssp_get_dma_params(ssp,
> + ((chn == 2) && (ttsa != 1)) || (width == 32),
> + substream->stream == SNDRV_PCM_STREAM_PLAYBACK);
>
> /* we can only change the settings if the port is not in use */
> if (ssp_read_reg(ssp, SSCR0) & SSCR0_SSE)
> --
> 1.6.0.4
>
regards
Philipp
More information about the Alsa-devel
mailing list