[alsa-devel] Gigabyte ALC889A Function ID: 0x01

Jerry Geis geisj at pagestation.com
Wed Apr 15 17:45:39 CEST 2009



Takashi Iwai wrote:
> At Wed, 15 Apr 2009 11:34:23 -0400,
> Jerry Geis wrote:
>   
>>
>> Takashi Iwai wrote:
>>     
>>> At Wed, 15 Apr 2009 11:14:20 -0400,
>>> Jerry Geis wrote:
>>>   
>>>       
>>>> Takashi Iwai wrote:
>>>>     
>>>>         
>>>>> At Wed, 15 Apr 2009 10:45:43 -0400,
>>>>> Jerry Geis wrote:
>>>>>   
>>>>>       
>>>>>           
>>>>>> Takashi Iwai wrote:
>>>>>>     
>>>>>>         
>>>>>>             
>>>>>>> At Wed, 15 Apr 2009 10:00:33 -0400,
>>>>>>> Jerry Geis wrote:
>>>>>>>   
>>>>>>>       
>>>>>>>           
>>>>>>>               
>>>>>>>> I am using the gigabyte MA78GM-US2H motherboard. it has the ALC889A audio.
>>>>>>>>
>>>>>>>> I am trying 1.0.19 and audio works out the analog back port but not over 
>>>>>>>> HDMI.
>>>>>>>>     
>>>>>>>>         
>>>>>>>>             
>>>>>>>>                 
>>>>>>> Never mind about "Function ID" entry.  It's just a new line that was
>>>>>>> added recently.  function_id=1 means it's an audio codec.
>>>>>>>
>>>>>>> The way HDMI is supported are mainly either through the same audio
>>>>>>> codec (ALC889A) or through a dedicated HDMI codec.  In the former
>>>>>>> case, you'll likely see a word "HDMI" in the digital output pin of the
>>>>>>> codec proc file.  In the latter case, you must have a different codec
>>>>>>> chip connected to the HD-audio bus with a different codec address
>>>>>>> number.
>>>>>>>
>>>>>>>
>>>>>>> Takashi
>>>>>>>
>>>>>>>
>>>>>>>   
>>>>>>>       
>>>>>>>           
>>>>>>>               
>>>>>>>> Codec: Realtek ALC889A
>>>>>>>> Address: 0
>>>>>>>> Function Id: 0x1                                     
>>>>>>>> <--------------------------------- this is different
>>>>>>>> Vendor Id: 0x10ec0885
>>>>>>>> Subsystem Id: 0x1458a002
>>>>>>>> Revision Id: 0x100101
>>>>>>>> No Modem Function Group found
>>>>>>>> Default PCM:
>>>>>>>>     rates [0x560]: 44100 48000 96000 192000
>>>>>>>>     bits [0xe]: 16 20 24
>>>>>>>>     formats [0x1]: PCM
>>>>>>>> Default Amp-In caps: N/A
>>>>>>>> Default Amp-Out caps: N/A
>>>>>>>> GPIO: io=2, o=0, i=0, unsolicited=1, wake=0
>>>>>>>>   IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
>>>>>>>>   IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
>>>>>>>> Node 0x02 [Audio Output] wcaps 0x11: Stereo
>>>>>>>>   Converter: stream=0, channel=0
>>>>>>>>   PCM:
>>>>>>>>     rates [0x560]: 44100 48000 96000 192000
>>>>>>>>     bits [0xe]: 16 20 24
>>>>>>>>     formats [0x1]: PCM
>>>>>>>> Node 0x03 [Audio Output] wcaps 0x11: Stereo
>>>>>>>>
>>>>>>>> I have been looking but havent found a solution yet. I tried grabbing 
>>>>>>>> the snapshot tar ball for today but I get errors on the compile.
>>>>>>>>
>>>>>>>> I had a similiar motherboard but it does not report Function ID: 01 : - 
>>>>>>>> HDMI audio on this board works correctly.
>>>>>>>> Codec: Realtek ALC889A
>>>>>>>> Address: 0
>>>>>>>> Vendor Id: 0x10ec0885
>>>>>>>> Subsystem Id: 0x1458a002
>>>>>>>> Revision Id: 0x100101
>>>>>>>> No Modem Function Group found
>>>>>>>> Default PCM:
>>>>>>>>     rates [0x560]: 44100 48000 96000 192000
>>>>>>>>
>>>>>>>> Any thoughts????
>>>>>>>>
>>>>>>>> Jerry
>>>>>>>> _______________________________________________
>>>>>>>> Alsa-devel mailing list
>>>>>>>> Alsa-devel at alsa-project.org
>>>>>>>> http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
>>>>>>>>
>>>>>>>>     
>>>>>>>>         
>>>>>>>>             
>>>>>>>>                 
>>>>>>>   
>>>>>>>       
>>>>>>>           
>>>>>>>               
>>>>>> I upload alsa-info.sh
>>>>>>
>>>>>> for the NOT WORKIng one 
>>>>>> http://www.alsa-project.org/db/?f=7e8bc9485e8bb98bf15dae5a0d5dc038003c3203
>>>>>>
>>>>>> for the working on 
>>>>>> http://www.alsa-project.org/db/?f=a18bcb6e87fe33a7365a749d0877a4546e901bf2
>>>>>>     
>>>>>>         
>>>>>>             
>>>>> How are you testing HDMI output?
>>>>>
>>>>>
>>>>> Takashi
>>>>>
>>>>>   
>>>>>       
>>>>>           
>>>> I have a sharp aquos HDMI that works with the other motherboard.
>>>>
>>>> I am just switching between the two.
>>>>
>>>> I have the asound.conf set to the correct hw:X,y on both machines for HDMI.
>>>>     
>>>>         
>>> More exactly?
>>>
>>> Also, try like below:
>>> 	% aplay -Dhdmi:1 foo.wav
>>>
>>> Takashi
>>>
>>>   
>>>       
>> When I run your command :
>> aplay -Dhdmi:1 /tmp/NewVoiceMale.wav
>> aplay: main:590: audio open error: Device or resource busy
>>     
>
> Is /dev/snd/hwC1D*p device being used by some app, such as a sound
> daemon?
>
>
> Takashi
>
>   
The file is present and doesnt seem to be used by anyone. lsof | grep hwC1

jerry


More information about the Alsa-devel mailing list