[alsa-devel] sbxfi - What works/doesn't summary

[The Source]

The Source пишет:
> The Source пишет:
>> Jason Harvey пишет:
>>> Takashi Iwai wrote:
>>>  
>>>>> Sorry that was a bit ambiguous, I'd never tried 96kHz.
>>>>> Have just changed base_rate to 96kHz and it performs identically 
>>>>> to 48kHz.
>>>>> Pulse mangles the sound in just the same manner at 48kHz or 96kHz.
>>>>>           
>>>> Ah, so you meant mplayer/flash with PA backend?
>>>>       
>>> Yes.
>>> I also tried mplayer using -ao=alsa or -ao=oss and the sound is 
>>> still corrupted, even after killing the pulse daemon.
>>>
>>> If I get the chance I will put the card into a 32bit machine 
>>> tomorrow and see how it sounds there.
>>>
>>> Thanks, Jason
>>>
>>>
>>> _______________________________________________
>>> Alsa-devel mailing list
>>> Alsa-devel at alsa-project.org
>>> http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
>>>
>>>   
>> Ok, looks like with the latest snapshot (28.10.2008 15:19:00) 
>> pulseaudio works fine. But wine not. The bad thing is I can't get 
>> hw_params somehow. When pulseaudio is started hw_params always say 
>> 'closed' even if sound is played at this moment. I'll try to remove 
>> pulseaudio and test wine again.
>>
> Well, I wasn't lucky. Even without pulseaudio hw_params are 'closed' 
> nomatter what.
>
Oh, forgot. My card is:

05:00.0 Multimedia audio controller: Creative Labs SB X-Fi
    Subsystem: Creative Labs Unknown device 002c
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64 (1000ns min, 1250ns max), Cache Line Size: 32 bytes
    Interrupt: pin A routed to IRQ 16
    Region 0: I/O ports at ec00 [size=32]
    Region 1: Memory at fea00000 (64-bit, non-prefetchable) [size=2M]
    Region 3: Memory at f8000000 (64-bit, non-prefetchable) [size=64M]
    Capabilities: [40] Power Management version 2
        Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ 
Queue=0/0 Enable-
        Address: 0000000000000000  Data: 0000
    Kernel driver in use: SB-XFi
00: 02 11 05 00 07 00 10 02 00 00 01 04 08 40 00 00
10: 01 ec 00 00 04 00 a0 fe 00 00 00 00 04 00 00 f8
20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 2c 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 04 05