[alsa-devel] [PATCH 1/2] ASoC: codecs: Add PCM186x binding documentation
Add the dt-binding documentation for the TI PCM186x 2ch and 4ch Audio ADCs With Universal Front End.
Signed-off-by: Andrew F. Davis afd@ti.com --- .../devicetree/bindings/sound/pcm186x.txt | 42 ++++++++++++++++++++++ 1 file changed, 42 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/pcm186x.txt
diff --git a/Documentation/devicetree/bindings/sound/pcm186x.txt b/Documentation/devicetree/bindings/sound/pcm186x.txt new file mode 100644 index 000000000000..0bc7d265c7bd --- /dev/null +++ b/Documentation/devicetree/bindings/sound/pcm186x.txt @@ -0,0 +1,42 @@ +Texas Instruments PCM186x Universal Audio ADC + +These devices support both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "ti,pcm1862", + "ti,pcm1863", + "ti,pcm1864", + "ti,pcm1865" + + - reg : The I2C address of the device for I2C, the chip select + number for SPI. + + - avdd-supply: Analog core power supply (3.3v) + - dvdd-supply: Digital core power supply + - iovdd-supply: Digital IO power supply + See regulator/regulator.txt for more information + +CODEC input pins: + * VINL1 + * VINR1 + * VINL2 + * VINR2 + * VINL3 + * VINR3 + * VINL4 + * VINR4 + +The pins can be used in referring sound node's audio-routing property. + +Example: + + pcm186x: pcm186x@4a { + compatible = "ti,pcm1865"; + reg = <0x4a>; + + avdd-supply = <®_3v3_analog>; + dvdd-supply = <®_3v3>; + iovdd-supply = <®_1v8>; + };
From: Andreas Dannenberg dannenberg@ti.com
This is an initial version of the PCM186x codec driver supporting both 2-channel and 4-channel device variants. Not all device features are supported yet such as master/slave mode PLL configuration for which the codec driver currently relies on the PCM186x built-in clock auto-detection feature or the connection of digital microphones. However here is what's here and what should work:
- Support for SPI and I2C low-level interfaces - Regmap support and basic register definitions - Input Mixer and Mux selection - I2C, LJ, and TDM DAI format support
Signed-off-by: Andreas Dannenberg dannenberg@ti.com Signed-off-by: Michael Stecklein m-stecklein@ti.com Signed-off-by: Andrew F. Davis afd@ti.com --- sound/soc/codecs/Kconfig | 17 + sound/soc/codecs/Makefile | 6 + sound/soc/codecs/pcm186x-i2c.c | 79 +++++ sound/soc/codecs/pcm186x-spi.c | 79 +++++ sound/soc/codecs/pcm186x.c | 778 +++++++++++++++++++++++++++++++++++++++++ sound/soc/codecs/pcm186x.h | 271 ++++++++++++++ 6 files changed, 1230 insertions(+) create mode 100644 sound/soc/codecs/pcm186x-i2c.c create mode 100644 sound/soc/codecs/pcm186x-spi.c create mode 100644 sound/soc/codecs/pcm186x.c create mode 100644 sound/soc/codecs/pcm186x.h
diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index c367d11079bc..c4f01f58fd2c 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -109,6 +109,8 @@ config SND_SOC_ALL_CODECS select SND_SOC_PCM1681 if I2C select SND_SOC_PCM179X_I2C if I2C select SND_SOC_PCM179X_SPI if SPI_MASTER + select SND_SOC_PCM186X_I2C if I2C + select SND_SOC_PCM186X_SPI if SPI_MASTER select SND_SOC_PCM3008 select SND_SOC_PCM3168A_I2C if I2C select SND_SOC_PCM3168A_SPI if SPI_MASTER @@ -661,6 +663,21 @@ config SND_SOC_PCM179X_SPI Enable support for Texas Instruments PCM179x CODEC. Select this if your PCM179x is connected via an SPI bus.
+config SND_SOC_PCM186X + tristate + +config SND_SOC_PCM186X_I2C + tristate "Texas Instruments PCM186x CODECs - I2C" + depends on I2C + select SND_SOC_PCM186X + select REGMAP_I2C + +config SND_SOC_PCM186X_SPI + tristate "Texas Instruments PCM186x CODECs - SPI" + depends on SPI_MASTER + select SND_SOC_PCM186X + select REGMAP_SPI + config SND_SOC_PCM3008 tristate
diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 05018b7ca72b..a660c969c1f7 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -105,6 +105,9 @@ snd-soc-pcm1681-objs := pcm1681.o snd-soc-pcm179x-codec-objs := pcm179x.o snd-soc-pcm179x-i2c-objs := pcm179x-i2c.o snd-soc-pcm179x-spi-objs := pcm179x-spi.o +snd-soc-pcm186x-objs := pcm186x.o +snd-soc-pcm186x-i2c-objs := pcm186x-i2c.o +snd-soc-pcm186x-spi-objs := pcm186x-spi.o snd-soc-pcm3008-objs := pcm3008.o snd-soc-pcm3168a-objs := pcm3168a.o snd-soc-pcm3168a-i2c-objs := pcm3168a-i2c.o @@ -345,6 +348,9 @@ obj-$(CONFIG_SND_SOC_PCM1681) += snd-soc-pcm1681.o obj-$(CONFIG_SND_SOC_PCM179X) += snd-soc-pcm179x-codec.o obj-$(CONFIG_SND_SOC_PCM179X_I2C) += snd-soc-pcm179x-i2c.o obj-$(CONFIG_SND_SOC_PCM179X_SPI) += snd-soc-pcm179x-spi.o +obj-$(CONFIG_SND_SOC_PCM186X) += snd-soc-pcm186x.o +obj-$(CONFIG_SND_SOC_PCM186X_I2C) += snd-soc-pcm186x-i2c.o +obj-$(CONFIG_SND_SOC_PCM186X_SPI) += snd-soc-pcm186x-spi.o obj-$(CONFIG_SND_SOC_PCM3008) += snd-soc-pcm3008.o obj-$(CONFIG_SND_SOC_PCM3168A) += snd-soc-pcm3168a.o obj-$(CONFIG_SND_SOC_PCM3168A_I2C) += snd-soc-pcm3168a-i2c.o diff --git a/sound/soc/codecs/pcm186x-i2c.c b/sound/soc/codecs/pcm186x-i2c.c new file mode 100644 index 000000000000..b42f1390d45b --- /dev/null +++ b/sound/soc/codecs/pcm186x-i2c.c @@ -0,0 +1,79 @@ +/* + * Texas Instruments PCM186x Universal Audio ADC - I2C + * + * Copyright (C) 2015-2017 Texas Instruments Incorporated - http://www.ti.com + * Andreas Dannenberg dannenberg@ti.com + * Andrew F. Davis afd@ti.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + */ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/i2c.h> + +#include "pcm186x.h" + +static const struct of_device_id pcm186x_of_match[] = { + { .compatible = "ti,pcm1862", .data = (void *)PCM1862 }, + { .compatible = "ti,pcm1863", .data = (void *)PCM1863 }, + { .compatible = "ti,pcm1864", .data = (void *)PCM1864 }, + { .compatible = "ti,pcm1865", .data = (void *)PCM1865 }, + { } +}; +MODULE_DEVICE_TABLE(of, pcm186x_of_match); + +static int pcm186x_i2c_probe(struct i2c_client *i2c, + const struct i2c_device_id *id) +{ + const enum pcm186x_type type = (enum pcm186x_type)id->driver_data; + int irq = i2c->irq; + struct regmap *regmap; + + dev_info(&i2c->dev, "%s() i2c->addr=%d\n", __func__, i2c->addr); + + regmap = devm_regmap_init_i2c(i2c, &pcm186x_regmap); + if (IS_ERR(regmap)) + return PTR_ERR(regmap); + + return pcm186x_probe(&i2c->dev, type, irq, regmap); +} + +static int pcm186x_i2c_remove(struct i2c_client *i2c) +{ + pcm186x_remove(&i2c->dev); + return 0; +} + +static const struct i2c_device_id pcm186x_i2c_id[] = { + { "pcm1862", PCM1862 }, + { "pcm1863", PCM1863 }, + { "pcm1864", PCM1864 }, + { "pcm1865", PCM1865 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, pcm186x_i2c_id); + +static struct i2c_driver pcm186x_i2c_driver = { + .probe = pcm186x_i2c_probe, + .remove = pcm186x_i2c_remove, + .id_table = pcm186x_i2c_id, + .driver = { + .name = "pcm186x", + .of_match_table = pcm186x_of_match, + .pm = &pcm186x_pm_ops, + }, +}; +module_i2c_driver(pcm186x_i2c_driver); + +MODULE_DESCRIPTION("PCM186x Universal Audio ADC I2C Interface Driver"); +MODULE_AUTHOR("Andreas Dannenberg dannenberg@ti.com"); +MODULE_AUTHOR("Andrew F. Davis afd@ti.com"); +MODULE_LICENSE("GPL v2"); diff --git a/sound/soc/codecs/pcm186x-spi.c b/sound/soc/codecs/pcm186x-spi.c new file mode 100644 index 000000000000..d15ccc20ef97 --- /dev/null +++ b/sound/soc/codecs/pcm186x-spi.c @@ -0,0 +1,79 @@ +/* + * Texas Instruments PCM186x Universal Audio ADC - SPI + * + * Copyright (C) 2015-2017 Texas Instruments Incorporated - http://www.ti.com + * Andreas Dannenberg dannenberg@ti.com + * Andrew F. Davis afd@ti.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + */ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/spi/spi.h> + +#include "pcm186x.h" + +static const struct of_device_id pcm186x_of_match[] = { + { .compatible = "ti,pcm1862", .data = (void *)PCM1862 }, + { .compatible = "ti,pcm1863", .data = (void *)PCM1863 }, + { .compatible = "ti,pcm1864", .data = (void *)PCM1864 }, + { .compatible = "ti,pcm1865", .data = (void *)PCM1865 }, + { } +}; +MODULE_DEVICE_TABLE(of, pcm186x_of_match); + +static int pcm186x_spi_probe(struct spi_device *spi) +{ + const enum pcm186x_type type = + (enum pcm186x_type)spi_get_device_id(spi)->driver_data; + int irq = spi->irq; + struct regmap *regmap; + + dev_info(&spi->dev, "%s()\n", __func__); + + regmap = devm_regmap_init_spi(spi, &pcm186x_regmap); + if (IS_ERR(regmap)) + return PTR_ERR(regmap); + + return pcm186x_probe(&spi->dev, type, irq, regmap); +} + +static int pcm186x_spi_remove(struct spi_device *spi) +{ + pcm186x_remove(&spi->dev); + return 0; +} + +static const struct spi_device_id pcm186x_spi_id[] = { + { "pcm1862", PCM1862 }, + { "pcm1863", PCM1863 }, + { "pcm1864", PCM1864 }, + { "pcm1865", PCM1865 }, + { } +}; +MODULE_DEVICE_TABLE(spi, pcm186x_spi_id); + +static struct spi_driver pcm186x_spi_driver = { + .probe = pcm186x_spi_probe, + .remove = pcm186x_spi_remove, + .id_table = pcm186x_spi_id, + .driver = { + .name = "pcm186x", + .of_match_table = pcm186x_of_match, + .pm = &pcm186x_pm_ops, + }, +}; +module_spi_driver(pcm186x_spi_driver); + +MODULE_DESCRIPTION("PCM186x Universal Audio ADC SPI Interface Driver"); +MODULE_AUTHOR("Andreas Dannenberg dannenberg@ti.com"); +MODULE_AUTHOR("Andrew F. Davis afd@ti.com"); +MODULE_LICENSE("GPL v2"); diff --git a/sound/soc/codecs/pcm186x.c b/sound/soc/codecs/pcm186x.c new file mode 100644 index 000000000000..7217d01d0347 --- /dev/null +++ b/sound/soc/codecs/pcm186x.c @@ -0,0 +1,778 @@ +/* + * Texas Instruments PCM186x Universal Audio ADC + * + * Copyright (C) 2015-2017 Texas Instruments Incorporated - http://www.ti.com + * Andreas Dannenberg dannenberg@ti.com + * Andrew F. Davis afd@ti.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + */ + +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/pm.h> +#include <linux/pm_runtime.h> +#include <linux/regulator/consumer.h> +#include <linux/regmap.h> +#include <linux/slab.h> +#include <sound/core.h> +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/jack.h> +#include <sound/initval.h> +#include <sound/tlv.h> + +#include "pcm186x.h" + +static const char * const pcm186x_supply_names[] = { + "avdd", /* Analog power supply. Connect to 3.3-V supply. */ + "dvdd", /* Digital power supply. Connect to 3.3-V supply. */ + "iovdd" /* I/O power supply. Connect to 3.3-V or 1.8-V. */ +}; +#define PCM186x_NUM_SUPPLIES ARRAY_SIZE(pcm186x_supply_names) + +struct pcm186x_priv { + struct regmap *regmap; + struct regulator_bulk_data supplies[PCM186x_NUM_SUPPLIES]; + unsigned int sysclk; + unsigned int tdm_offset; + bool is_tdm_mode; + bool is_master_mode; +}; + +static const DECLARE_TLV_DB_SCALE(pcm186x_pga_tlv, -1200, 4000, 50); + +static const struct snd_kcontrol_new pcm1863_snd_controls[] = { + SOC_DOUBLE_R_S_TLV("Analog Gain", PCM186X_PGA_VAL_CH1_L, + PCM186X_PGA_VAL_CH1_R, 0, -24, 80, 7, 0, + pcm186x_pga_tlv), +}; + +static const struct snd_kcontrol_new pcm1865_snd_controls[] = { + SOC_DOUBLE_R_S_TLV("ADC1 Analog Gain", PCM186X_PGA_VAL_CH1_L, + PCM186X_PGA_VAL_CH1_R, 0, -24, 80, 7, 0, + pcm186x_pga_tlv), + SOC_DOUBLE_R_S_TLV("ADC2 Analog Gain", PCM186X_PGA_VAL_CH2_L, + PCM186X_PGA_VAL_CH2_R, 0, -24, 80, 7, 0, + pcm186x_pga_tlv), +}; + +const unsigned int pcm186x_adc_input_channel_sel_value[] = { + 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07, + 0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f, + 0x10, 0x20, 0x30 +}; + +static const char * const pcm186x_adcl_input_channel_sel_text[] = { + "No Select", + "VINL1[SE]", /* Default for ADC1L */ + "VINL2[SE]", /* Default for ADC2L */ + "VINL2[SE] + VINL1[SE]", + "VINL3[SE]", + "VINL3[SE] + VINL1[SE]", + "VINL3[SE] + VINL2[SE]", + "VINL3[SE] + VINL2[SE] + VINL1[SE]", + "VINL4[SE]", + "VINL4[SE] + VINL1[SE]", + "VINL4[SE] + VINL2[SE]", + "VINL4[SE] + VINL2[SE] + VINL1[SE]", + "VINL4[SE] + VINL3[SE]", + "VINL4[SE] + VINL3[SE] + VINL1[SE]", + "VINL4[SE] + VINL3[SE] + VINL2[SE]", + "VINL4[SE] + VINL3[SE] + VINL2[SE] + VINL1[SE]", + "{VIN1P, VIN1M}[DIFF]", + "{VIN4P, VIN4M}[DIFF]", + "{VIN1P, VIN1M}[DIFF] + {VIN4P, VIN4M}[DIFF]" +}; + +static const char * const pcm186x_adcr_input_channel_sel_text[] = { + "No Select", + "VINR1[SE]", /* Default for ADC1R */ + "VINR2[SE]", /* Default for ADC2R */ + "VINR2[SE] + VINR1[SE]", + "VINR3[SE]", + "VINR3[SE] + VINR1[SE]", + "VINR3[SE] + VINR2[SE]", + "VINR3[SE] + VINR2[SE] + VINR1[SE]", + "VINR4[SE]", + "VINR4[SE] + VINR1[SE]", + "VINR4[SE] + VINR2[SE]", + "VINR4[SE] + VINR2[SE] + VINR1[SE]", + "VINR4[SE] + VINR3[SE]", + "VINR4[SE] + VINR3[SE] + VINR1[SE]", + "VINR4[SE] + VINR3[SE] + VINR2[SE]", + "VINR4[SE] + VINR3[SE] + VINR2[SE] + VINR1[SE]", + "{VIN2P, VIN2M}[DIFF]", + "{VIN3P, VIN3M}[DIFF]", + "{VIN2P, VIN2M}[DIFF] + {VIN3P, VIN3M}[DIFF]" +}; + +static const struct soc_enum pcm186x_adc_input_channel_sel[] = { + SOC_VALUE_ENUM_SINGLE(PCM186X_ADC1_INPUT_SEL_L, 0, + PCM186X_ADC_INPUT_SEL_MASK, + ARRAY_SIZE(pcm186x_adcl_input_channel_sel_text), + pcm186x_adcl_input_channel_sel_text, + pcm186x_adc_input_channel_sel_value), + SOC_VALUE_ENUM_SINGLE(PCM186X_ADC1_INPUT_SEL_R, 0, + PCM186X_ADC_INPUT_SEL_MASK, + ARRAY_SIZE(pcm186x_adcr_input_channel_sel_text), + pcm186x_adcr_input_channel_sel_text, + pcm186x_adc_input_channel_sel_value), + SOC_VALUE_ENUM_SINGLE(PCM186X_ADC2_INPUT_SEL_L, 0, + PCM186X_ADC_INPUT_SEL_MASK, + ARRAY_SIZE(pcm186x_adcl_input_channel_sel_text), + pcm186x_adcl_input_channel_sel_text, + pcm186x_adc_input_channel_sel_value), + SOC_VALUE_ENUM_SINGLE(PCM186X_ADC2_INPUT_SEL_R, 0, + PCM186X_ADC_INPUT_SEL_MASK, + ARRAY_SIZE(pcm186x_adcr_input_channel_sel_text), + pcm186x_adcr_input_channel_sel_text, + pcm186x_adc_input_channel_sel_value), +}; + +static const struct snd_kcontrol_new pcm186x_adc_mux_controls[] = { + SOC_DAPM_ENUM("ADC1 Left Input", pcm186x_adc_input_channel_sel[0]), + SOC_DAPM_ENUM("ADC1 Right Input", pcm186x_adc_input_channel_sel[1]), + SOC_DAPM_ENUM("ADC2 Left Input", pcm186x_adc_input_channel_sel[2]), + SOC_DAPM_ENUM("ADC2 Right Input", pcm186x_adc_input_channel_sel[3]), +}; + +static const struct snd_soc_dapm_widget pcm1863_dapm_widgets[] = { + SND_SOC_DAPM_INPUT("VINL1"), + SND_SOC_DAPM_INPUT("VINR1"), + SND_SOC_DAPM_INPUT("VINL2"), + SND_SOC_DAPM_INPUT("VINR2"), + SND_SOC_DAPM_INPUT("VINL3"), + SND_SOC_DAPM_INPUT("VINR3"), + SND_SOC_DAPM_INPUT("VINL4"), + SND_SOC_DAPM_INPUT("VINR4"), + + SND_SOC_DAPM_MUX("ADC Left Capture Source", SND_SOC_NOPM, 0, 0, + &pcm186x_adc_mux_controls[0]), + SND_SOC_DAPM_MUX("ADC Right Capture Source", SND_SOC_NOPM, 0, 0, + &pcm186x_adc_mux_controls[1]), + + /* + * Put the codec into SLEEP mode when not in use, allowing the + * Energysense mechanism to operate. + */ + SND_SOC_DAPM_ADC("ADC", "HiFi Capture", PCM186X_POWER_CTRL, 1, 0), +}; + +static const struct snd_soc_dapm_widget pcm1865_dapm_widgets[] = { + SND_SOC_DAPM_INPUT("VINL1"), + SND_SOC_DAPM_INPUT("VINR1"), + SND_SOC_DAPM_INPUT("VINL2"), + SND_SOC_DAPM_INPUT("VINR2"), + SND_SOC_DAPM_INPUT("VINL3"), + SND_SOC_DAPM_INPUT("VINR3"), + SND_SOC_DAPM_INPUT("VINL4"), + SND_SOC_DAPM_INPUT("VINR4"), + + SND_SOC_DAPM_MUX("ADC1 Left Capture Source", SND_SOC_NOPM, 0, 0, + &pcm186x_adc_mux_controls[0]), + SND_SOC_DAPM_MUX("ADC1 Right Capture Source", SND_SOC_NOPM, 0, 0, + &pcm186x_adc_mux_controls[1]), + SND_SOC_DAPM_MUX("ADC2 Left Capture Source", SND_SOC_NOPM, 0, 0, + &pcm186x_adc_mux_controls[2]), + SND_SOC_DAPM_MUX("ADC2 Right Capture Source", SND_SOC_NOPM, 0, 0, + &pcm186x_adc_mux_controls[3]), + + /* + * Put the codec into SLEEP mode when not in use, allowing the + * Energysense mechanism to operate. + */ + SND_SOC_DAPM_ADC("ADC1", "HiFi Capture 1", PCM186X_POWER_CTRL, 1, 0), + SND_SOC_DAPM_ADC("ADC2", "HiFi Capture 2", PCM186X_POWER_CTRL, 1, 0), +}; + +static const struct snd_soc_dapm_route pcm1863_dapm_routes[] = { + { "ADC Left Capture Source", NULL, "VINL1" }, + { "ADC Left Capture Source", NULL, "VINR1" }, + { "ADC Left Capture Source", NULL, "VINL2" }, + { "ADC Left Capture Source", NULL, "VINR2" }, + { "ADC Left Capture Source", NULL, "VINL3" }, + { "ADC Left Capture Source", NULL, "VINR3" }, + { "ADC Left Capture Source", NULL, "VINL4" }, + { "ADC Left Capture Source", NULL, "VINR4" }, + + { "ADC", NULL, "ADC Left Capture Source" }, + + { "ADC Right Capture Source", NULL, "VINL1" }, + { "ADC Right Capture Source", NULL, "VINR1" }, + { "ADC Right Capture Source", NULL, "VINL2" }, + { "ADC Right Capture Source", NULL, "VINR2" }, + { "ADC Right Capture Source", NULL, "VINL3" }, + { "ADC Right Capture Source", NULL, "VINR3" }, + { "ADC Right Capture Source", NULL, "VINL4" }, + { "ADC Right Capture Source", NULL, "VINR4" }, + + { "ADC", NULL, "ADC Right Capture Source" }, +}; + +static const struct snd_soc_dapm_route pcm1865_dapm_routes[] = { + { "ADC1 Left Capture Source", NULL, "VINL1" }, + { "ADC1 Left Capture Source", NULL, "VINR1" }, + { "ADC1 Left Capture Source", NULL, "VINL2" }, + { "ADC1 Left Capture Source", NULL, "VINR2" }, + { "ADC1 Left Capture Source", NULL, "VINL3" }, + { "ADC1 Left Capture Source", NULL, "VINR3" }, + { "ADC1 Left Capture Source", NULL, "VINL4" }, + { "ADC1 Left Capture Source", NULL, "VINR4" }, + + { "ADC1", NULL, "ADC1 Left Capture Source" }, + + { "ADC1 Right Capture Source", NULL, "VINL1" }, + { "ADC1 Right Capture Source", NULL, "VINR1" }, + { "ADC1 Right Capture Source", NULL, "VINL2" }, + { "ADC1 Right Capture Source", NULL, "VINR2" }, + { "ADC1 Right Capture Source", NULL, "VINL3" }, + { "ADC1 Right Capture Source", NULL, "VINR3" }, + { "ADC1 Right Capture Source", NULL, "VINL4" }, + { "ADC1 Right Capture Source", NULL, "VINR4" }, + + { "ADC1", NULL, "ADC1 Right Capture Source" }, + + { "ADC2 Left Capture Source", NULL, "VINL1" }, + { "ADC2 Left Capture Source", NULL, "VINR1" }, + { "ADC2 Left Capture Source", NULL, "VINL2" }, + { "ADC2 Left Capture Source", NULL, "VINR2" }, + { "ADC2 Left Capture Source", NULL, "VINL3" }, + { "ADC2 Left Capture Source", NULL, "VINR3" }, + { "ADC2 Left Capture Source", NULL, "VINL4" }, + { "ADC2 Left Capture Source", NULL, "VINR4" }, + + { "ADC2", NULL, "ADC2 Left Capture Source" }, + + { "ADC2 Right Capture Source", NULL, "VINL1" }, + { "ADC2 Right Capture Source", NULL, "VINR1" }, + { "ADC2 Right Capture Source", NULL, "VINL2" }, + { "ADC2 Right Capture Source", NULL, "VINR2" }, + { "ADC2 Right Capture Source", NULL, "VINL3" }, + { "ADC2 Right Capture Source", NULL, "VINR3" }, + { "ADC2 Right Capture Source", NULL, "VINL4" }, + { "ADC2 Right Capture Source", NULL, "VINR4" }, + + { "ADC2", NULL, "ADC2 Right Capture Source" }, +}; + +static int pcm186x_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_codec *codec = dai->codec; + + struct pcm186x_priv *priv = snd_soc_codec_get_drvdata(codec); + unsigned int rate = params_rate(params); + unsigned int format = params_format(params); + unsigned int width = params_width(params); + unsigned int channels = params_channels(params); + unsigned int div_lrck; + unsigned int div_bck; + u8 tdm_tx_sel = 0; + u8 pcm_cfg = 0; + int ret; + + dev_dbg(codec->dev, "%s() rate=%u format=0x%x width=%u channels=%u\n", + __func__, rate, format, width, channels); + + switch (width) { + case 16: + pcm_cfg = PCM186X_PCM_CFG_RX_WLEN_16 | + PCM186X_PCM_CFG_TX_WLEN_16; + break; + case 20: + pcm_cfg = PCM186X_PCM_CFG_RX_WLEN_20 | + PCM186X_PCM_CFG_TX_WLEN_20; + break; + case 24: + pcm_cfg = PCM186X_PCM_CFG_RX_WLEN_24 | + PCM186X_PCM_CFG_TX_WLEN_24; + break; + case 32: + pcm_cfg = PCM186X_PCM_CFG_RX_WLEN_32 | + PCM186X_PCM_CFG_TX_WLEN_32; + break; + default: + return -EINVAL; + } + + snd_soc_update_bits(codec, PCM186X_PCM_CFG, + PCM186X_PCM_CFG_RX_WLEN_MASK | + PCM186X_PCM_CFG_TX_WLEN_MASK, + pcm_cfg); + + div_lrck = width * channels; + + if (priv->is_tdm_mode) { + /* Select TDM transmission data */ + switch (channels) { + case 2: + tdm_tx_sel = PCM186X_TDM_TX_SEL_2CH; + break; + case 4: + tdm_tx_sel = PCM186X_TDM_TX_SEL_4CH; + break; + case 6: + tdm_tx_sel = PCM186X_TDM_TX_SEL_6CH; + break; + default: + return -EINVAL; + } + + snd_soc_update_bits(codec, PCM186X_TDM_TX_SEL, + PCM186X_TDM_TX_SEL_MASK, tdm_tx_sel); + + /* In DSP/TDM mode, the LRCLK divider must be 256 */ + div_lrck = 256; + + /* Configure 1/256 duty cycle for LRCK */ + snd_soc_update_bits(codec, PCM186X_PCM_CFG, + PCM186X_PCM_CFG_TDM_LRCK_MODE, + PCM186X_PCM_CFG_TDM_LRCK_MODE); + } + + /* Only configure clock dividers in master mode. */ + if (priv->is_master_mode) { + div_bck = priv->sysclk / (div_lrck * rate); + + dev_dbg(codec->dev, + "%s() master_clk=%u div_bck=%u div_lrck=%u\n", + __func__, priv->sysclk, div_bck, div_lrck); + + ret = regmap_write(priv->regmap, PCM186X_BCK_DIV, div_bck - 1); + if (ret < 0) { + dev_err(codec->dev, + "failed to write register: %d\n", ret); + return ret; + } + + ret = regmap_write(priv->regmap, PCM186X_LRK_DIV, + div_lrck - 1); + if (ret < 0) { + dev_err(codec->dev, "failed to write register: %d\n", + ret); + return ret; + } + } + + return 0; +} + +static int pcm186x_set_fmt(struct snd_soc_dai *dai, unsigned int format) +{ + struct snd_soc_codec *codec = dai->codec; + struct pcm186x_priv *priv = snd_soc_codec_get_drvdata(codec); + u8 clk_ctrl = 0; + u8 pcm_cfg = 0; + + dev_dbg(codec->dev, "%s() format=0x%x\n", __func__, format); + + /* set master/slave audio interface */ + switch (format & SND_SOC_DAIFMT_MASTER_MASK) { + case SND_SOC_DAIFMT_CBM_CFM: + if (!priv->sysclk) { + dev_err(codec->dev, "operating in master mode requires sysclock to be configured!\n"); + return -EINVAL; + } + clk_ctrl |= PCM186X_CLK_CTRL_MST_MODE; + priv->is_master_mode = true; + break; + case SND_SOC_DAIFMT_CBS_CFS: + priv->is_master_mode = false; + break; + default: + dev_alert(codec->dev, "Invalid DAI master/slave interface\n"); + return -EINVAL; + } + + snd_soc_update_bits(codec, PCM186X_CLK_CTRL, + PCM186X_CLK_CTRL_MST_MODE, clk_ctrl); + + /* set interface polarity */ + switch (format & SND_SOC_DAIFMT_INV_MASK) { + case SND_SOC_DAIFMT_NB_NF: + break; + default: + dev_alert(codec->dev, "Inverted DAI clocks not supported\n"); + return -EINVAL; + } + + /* set interface format */ + switch (format & SND_SOC_DAIFMT_FORMAT_MASK) { + case SND_SOC_DAIFMT_I2S: + pcm_cfg = PCM186X_PCM_CFG_FMT_I2S; + break; + case SND_SOC_DAIFMT_LEFT_J: + pcm_cfg = PCM186X_PCM_CFG_FMT_LEFTJ; + break; + case SND_SOC_DAIFMT_DSP_A: + priv->tdm_offset += 1; + /* Fall through... DSP_A uses the same basic config as DSP_B + * except we need to shift the TDM output by one BCK cycle + */ + case SND_SOC_DAIFMT_DSP_B: + priv->is_tdm_mode = true; + pcm_cfg = PCM186X_PCM_CFG_FMT_TDM; + break; + default: + return -EINVAL; + } + + snd_soc_write(codec, PCM186X_TDM_TX_OFFSET, priv->tdm_offset); + + snd_soc_update_bits(codec, PCM186X_PCM_CFG, + PCM186X_PCM_CFG_FMT_MASK, pcm_cfg); + + return 0; +} + +static int pcm186x_set_tdm_slot(struct snd_soc_dai *dai, unsigned int tx_mask, + unsigned int rx_mask, int slots, int slot_width) +{ + struct snd_soc_codec *codec = dai->codec; + struct pcm186x_priv *priv = snd_soc_codec_get_drvdata(codec); + unsigned int first_slot, last_slot, tdm_offset; + + dev_dbg(codec->dev, + "%s() tx_mask=0x%x rx_mask=0x%x slots=%d slot_width=%d\n", + __func__, tx_mask, rx_mask, slots, slot_width); + + if (!tx_mask) { + dev_err(codec->dev, "tdm tx mask must not be 0\n"); + return -EINVAL; + } + + first_slot = __ffs(tx_mask); + last_slot = __fls(tx_mask); + + if (last_slot - first_slot != hweight32(tx_mask) - 1) { + dev_err(codec->dev, "tdm tx mask must be contiguous\n"); + return -EINVAL; + } + + tdm_offset = first_slot * slot_width; + + if (tdm_offset > 255) { + dev_err(codec->dev, "tdm tx slot selection out of bounds\n"); + return -EINVAL; + } + + priv->tdm_offset = tdm_offset; + + return 0; +} + +static int pcm186x_set_dai_sysclk(struct snd_soc_dai *dai, int clk_id, + unsigned int freq, int dir) +{ + struct snd_soc_codec *codec = dai->codec; + struct pcm186x_priv *priv = snd_soc_codec_get_drvdata(codec); + + dev_dbg(codec->dev, "%s() clk_id=%d freq=%u dir=%d\n", + __func__, clk_id, freq, dir); + + priv->sysclk = freq; + + return 0; +} + +const struct snd_soc_dai_ops pcm186x_dai_ops = { + .set_sysclk = pcm186x_set_dai_sysclk, + .set_tdm_slot = pcm186x_set_tdm_slot, + .set_fmt = pcm186x_set_fmt, + .hw_params = pcm186x_hw_params, + +}; + +static struct snd_soc_dai_driver pcm1863_dai = { + .name = "pcm1863-aif", + .capture = { + .stream_name = "AIF Capture", + .channels_min = 1, + .channels_max = 2, + .rates = PCM186X_RATES, + .formats = PCM186X_FORMATS, + }, + .ops = &pcm186x_dai_ops, +}; + +static struct snd_soc_dai_driver pcm1865_dai = { + .name = "pcm1865-aif", + .capture = { + .stream_name = "AIF Capture", + .channels_min = 1, + .channels_max = 4, + .rates = PCM186X_RATES, + .formats = PCM186X_FORMATS, + }, + .ops = &pcm186x_dai_ops, +}; + +static int pcm186x_power_on(struct snd_soc_codec *codec) +{ + struct pcm186x_priv *priv = snd_soc_codec_get_drvdata(codec); + int ret = 0; + + ret = regulator_bulk_enable(ARRAY_SIZE(priv->supplies), + priv->supplies); + if (ret) + return ret; + + regcache_cache_only(priv->regmap, false); + ret = regcache_sync(priv->regmap); + if (ret != 0) { + dev_err(codec->dev, "Failed to restore cache\n"); + regcache_cache_only(priv->regmap, true); + regulator_bulk_disable(ARRAY_SIZE(priv->supplies), + priv->supplies); + return ret; + } + + return 0; +} + +static int pcm186x_power_off(struct snd_soc_codec *codec) +{ + struct pcm186x_priv *priv = snd_soc_codec_get_drvdata(codec); + int ret; + + regcache_cache_only(priv->regmap, true); + ret = regulator_bulk_disable(ARRAY_SIZE(priv->supplies), + priv->supplies); + if (ret) + return ret; + + return 0; +} + +static int pcm186x_set_bias_level(struct snd_soc_codec *codec, + enum snd_soc_bias_level level) +{ + dev_dbg(codec->dev, "## %s: %d -> %d\n", __func__, + snd_soc_codec_get_bias_level(codec), level); + + switch (level) { + case SND_SOC_BIAS_ON: + break; + case SND_SOC_BIAS_PREPARE: + break; + case SND_SOC_BIAS_STANDBY: + pcm186x_power_on(codec); + break; + case SND_SOC_BIAS_OFF: + pcm186x_power_off(codec); + break; + } + + return 0; +} + +static struct snd_soc_codec_driver soc_codec_dev_pcm1863 = { + .set_bias_level = pcm186x_set_bias_level, + + .component_driver = { + .controls = pcm1863_snd_controls, + .num_controls = ARRAY_SIZE(pcm1863_snd_controls), + .dapm_widgets = pcm1863_dapm_widgets, + .num_dapm_widgets = ARRAY_SIZE(pcm1863_dapm_widgets), + .dapm_routes = pcm1863_dapm_routes, + .num_dapm_routes = ARRAY_SIZE(pcm1863_dapm_routes), + }, +}; + +static struct snd_soc_codec_driver soc_codec_dev_pcm1865 = { + .set_bias_level = pcm186x_set_bias_level, + + .component_driver = { + .controls = pcm1865_snd_controls, + .num_controls = ARRAY_SIZE(pcm1865_snd_controls), + .dapm_widgets = pcm1865_dapm_widgets, + .num_dapm_widgets = ARRAY_SIZE(pcm1865_dapm_widgets), + .dapm_routes = pcm1865_dapm_routes, + .num_dapm_routes = ARRAY_SIZE(pcm1865_dapm_routes), + }, +}; + +static bool pcm186x_volatile(struct device *dev, unsigned int reg) +{ + switch (reg) { + case PCM186X_PAGE: + case PCM186X_DEVICE_STATUS: + case PCM186X_FSAMPLE_STATUS: + case PCM186X_DIV_STATUS: + case PCM186X_CLK_STATUS: + case PCM186X_SUPPLY_STATUS: + case PCM186X_MMAP_STAT_CTRL: + case PCM186X_MMAP_ADDRESS: + return true; + } + + return false; +} + +/* + * The PCM186x's page register is located on every page, allowing to program it + * without having to switch pages. Take advantage of this by defining the range + * such to have this register located inside the data window. + */ +static const struct regmap_range_cfg pcm186x_range = { + .name = "Pages", + .range_max = PCM186X_MAX_REGISTER, + .selector_reg = PCM186X_PAGE, + .selector_mask = 0xff, + .window_len = PCM186X_PAGE_LEN, +}; + +const struct regmap_config pcm186x_regmap = { + .reg_bits = 8, + .val_bits = 8, + + .volatile_reg = pcm186x_volatile, + + .ranges = &pcm186x_range, + .num_ranges = 1, + + .max_register = PCM186X_MAX_REGISTER, + + .cache_type = REGCACHE_RBTREE, +}; +EXPORT_SYMBOL_GPL(pcm186x_regmap); + +int pcm186x_probe(struct device *dev, enum pcm186x_type type, int irq, + struct regmap *regmap) +{ + struct pcm186x_priv *priv; + int i, ret; + + dev_dbg(dev, "%s()\n", __func__); + + priv = devm_kzalloc(dev, sizeof(struct pcm186x_priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + dev_set_drvdata(dev, priv); + priv->regmap = regmap; + + for (i = 0; i < ARRAY_SIZE(priv->supplies); i++) + priv->supplies[i].supply = pcm186x_supply_names[i]; + + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(priv->supplies), + priv->supplies); + if (ret != 0) { + dev_err(dev, "failed to request supplies: %d\n", ret); + return ret; + } + + /* Reset device registers for a consistent power-on like state */ + ret = regmap_write(regmap, PCM186X_PAGE, PCM186X_RESET); + if (ret != 0) { + dev_err(dev, "failed to write device: %d\n", ret); + return ret; + } + + switch (type) { + case PCM1865: + case PCM1864: + ret = snd_soc_register_codec(dev, &soc_codec_dev_pcm1865, + &pcm1865_dai, 1); + break; + case PCM1863: + case PCM1862: + /* Fall through... */ + default: + ret = snd_soc_register_codec(dev, &soc_codec_dev_pcm1863, + &pcm1863_dai, 1); + } + if (ret != 0) { + dev_err(dev, "failed to register CODEC: %d\n", ret); + return ret; + } + + return 0; +} +EXPORT_SYMBOL_GPL(pcm186x_probe); + +int pcm186x_remove(struct device *dev) +{ + snd_soc_unregister_codec(dev); + + return 0; +} +EXPORT_SYMBOL_GPL(pcm186x_remove); + +static int __maybe_unused pcm186x_suspend(struct device *dev) +{ + struct pcm186x_priv *priv = dev_get_drvdata(dev); + int ret; + + dev_dbg(dev, "%s()\n", __func__); + + ret = regmap_update_bits(priv->regmap, PCM186X_POWER_CTRL, + PCM186X_PWR_CTRL_PWRDN, + PCM186X_PWR_CTRL_PWRDN); + if (ret != 0) { + dev_err(dev, "failed to write register: %d\n", ret); + return ret; + } + + ret = regulator_bulk_disable(ARRAY_SIZE(priv->supplies), + priv->supplies); + if (ret != 0) { + dev_err(dev, "failed to disable supplies: %d\n", ret); + return ret; + } + + return 0; +} + +static int __maybe_unused pcm186x_resume(struct device *dev) +{ + struct pcm186x_priv *priv = dev_get_drvdata(dev); + int ret; + + dev_dbg(dev, "%s()\n", __func__); + + ret = regulator_bulk_enable(ARRAY_SIZE(priv->supplies), + priv->supplies); + if (ret != 0) { + dev_err(dev, "failed to enable supplies: %d\n", ret); + return ret; + } + + regcache_cache_only(priv->regmap, false); + ret = regcache_sync(priv->regmap); + if (ret != 0) { + dev_err(dev, "failed to sync cache: %d\n", ret); + return ret; + } + + ret = regmap_update_bits(priv->regmap, PCM186X_POWER_CTRL, + PCM186X_PWR_CTRL_PWRDN, 0); + if (ret != 0) { + dev_err(dev, "failed to write register: %d\n", ret); + return ret; + } + + return 0; +} + +const struct dev_pm_ops pcm186x_pm_ops = { + SET_RUNTIME_PM_OPS(pcm186x_suspend, pcm186x_resume, NULL) +}; +EXPORT_SYMBOL_GPL(pcm186x_pm_ops); + +MODULE_DESCRIPTION("PCM186x Universal Audio ADC driver"); +MODULE_AUTHOR("Andreas Dannenberg dannenberg@ti.com"); +MODULE_AUTHOR("Andrew F. Davis afd@ti.com"); +MODULE_LICENSE("GPL v2"); diff --git a/sound/soc/codecs/pcm186x.h b/sound/soc/codecs/pcm186x.h new file mode 100644 index 000000000000..631f7db8e868 --- /dev/null +++ b/sound/soc/codecs/pcm186x.h @@ -0,0 +1,271 @@ +/* + * Texas Instruments PCM186x Universal Audio ADC + * + * Copyright (C) 2015-2017 Texas Instruments Incorporated - http://www.ti.com + * Andreas Dannenberg dannenberg@ti.com + * Andrew F. Davis afd@ti.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + */ + +#ifndef _PCM186X_H_ +#define _PCM186X_H_ + +#include <linux/pm.h> +#include <linux/regmap.h> + +enum pcm186x_type { + PCM1862, + PCM1863, + PCM1864, + PCM1865, +}; + +#define PCM186X_RATES SNDRV_PCM_RATE_8000_192000 +#define PCM186X_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | \ + SNDRV_PCM_FMTBIT_S20_3LE |\ + SNDRV_PCM_FMTBIT_S24_LE | \ + SNDRV_PCM_FMTBIT_S32_LE) + +#define PCM186X_PAGE_LEN 0x0100 +#define PCM186X_PAGE_BASE(n) (PCM186X_PAGE_LEN * n) + +/* The page selection register address is the same on all pages */ +#define PCM186X_PAGE 0 + +/* Register Definitions - Page 0 */ +#define PCM186X_PGA_VAL_CH1_L (PCM186X_PAGE_BASE(0) + 1) +#define PCM186X_PGA_VAL_CH1_R (PCM186X_PAGE_BASE(0) + 2) +#define PCM186X_PGA_VAL_CH2_L (PCM186X_PAGE_BASE(0) + 3) +#define PCM186X_PGA_VAL_CH2_R (PCM186X_PAGE_BASE(0) + 4) +#define PCM186X_PGA_CTRL (PCM186X_PAGE_BASE(0) + 5) +#define PCM186X_ADC1_INPUT_SEL_L (PCM186X_PAGE_BASE(0) + 6) +#define PCM186X_ADC1_INPUT_SEL_R (PCM186X_PAGE_BASE(0) + 7) +#define PCM186X_ADC2_INPUT_SEL_L (PCM186X_PAGE_BASE(0) + 8) +#define PCM186X_ADC2_INPUT_SEL_R (PCM186X_PAGE_BASE(0) + 9) +#define PCM186X_AUXADC_INPUT_SEL (PCM186X_PAGE_BASE(0) + 10) +#define PCM186X_PCM_CFG (PCM186X_PAGE_BASE(0) + 11) +#define PCM186X_TDM_TX_SEL (PCM186X_PAGE_BASE(0) + 12) +#define PCM186X_TDM_TX_OFFSET (PCM186X_PAGE_BASE(0) + 13) +#define PCM186X_TDM_RX_OFFSET (PCM186X_PAGE_BASE(0) + 14) +#define PCM186X_DPGA_VAL_CH1_L (PCM186X_PAGE_BASE(0) + 15) +#define PCM186X_GPIO1_0_CTRL (PCM186X_PAGE_BASE(0) + 16) +#define PCM186X_GPIO3_2_CTRL (PCM186X_PAGE_BASE(0) + 17) +#define PCM186X_GPIO1_0_DIR_CTRL (PCM186X_PAGE_BASE(0) + 18) +#define PCM186X_GPIO3_2_DIR_CTRL (PCM186X_PAGE_BASE(0) + 19) +#define PCM186X_GPIO_IN_OUT (PCM186X_PAGE_BASE(0) + 20) +#define PCM186X_GPIO_PULL_CTRL (PCM186X_PAGE_BASE(0) + 21) +#define PCM186X_DPGA_VAL_CH1_R (PCM186X_PAGE_BASE(0) + 22) +#define PCM186X_DPGA_VAL_CH2_L (PCM186X_PAGE_BASE(0) + 23) +#define PCM186X_DPGA_VAL_CH2_R (PCM186X_PAGE_BASE(0) + 24) +#define PCM186X_DPGA_GAIN_CTRL (PCM186X_PAGE_BASE(0) + 25) +#define PCM186X_DPGA_MIC_CTRL (PCM186X_PAGE_BASE(0) + 26) +#define PCM186X_DIN_RESAMP_CTRL (PCM186X_PAGE_BASE(0) + 27) +#define PCM186X_CLK_CTRL (PCM186X_PAGE_BASE(0) + 32) +#define PCM186X_DSP1_CLK_DIV (PCM186X_PAGE_BASE(0) + 33) +#define PCM186X_DSP2_CLK_DIV (PCM186X_PAGE_BASE(0) + 34) +#define PCM186X_ADC_CLK_DIV (PCM186X_PAGE_BASE(0) + 35) +#define PCM186X_PLL_SCK_DIV (PCM186X_PAGE_BASE(0) + 37) +#define PCM186X_BCK_DIV (PCM186X_PAGE_BASE(0) + 38) +#define PCM186X_LRK_DIV (PCM186X_PAGE_BASE(0) + 39) +#define PCM186X_PLL_CTRL (PCM186X_PAGE_BASE(0) + 40) +#define PCM186X_PLL_P_DIV (PCM186X_PAGE_BASE(0) + 41) +#define PCM186X_PLL_R_DIV (PCM186X_PAGE_BASE(0) + 42) +#define PCM186X_PLL_J_DIV (PCM186X_PAGE_BASE(0) + 43) +#define PCM186X_PLL_D_DIV_LSB (PCM186X_PAGE_BASE(0) + 44) +#define PCM186X_PLL_D_DIV_MSB (PCM186X_PAGE_BASE(0) + 45) +#define PCM186X_SIGDET_MODE (PCM186X_PAGE_BASE(0) + 48) +#define PCM186X_SIGDET_MASK (PCM186X_PAGE_BASE(0) + 49) +#define PCM186X_SIGDET_STAT (PCM186X_PAGE_BASE(0) + 50) +#define PCM186X_SIGDET_LOSS_TIME (PCM186X_PAGE_BASE(0) + 52) +#define PCM186X_SIGDET_SCAN_TIME (PCM186X_PAGE_BASE(0) + 53) +#define PCM186X_SIGDET_INT_INTVL (PCM186X_PAGE_BASE(0) + 54) +#define PCM186X_SIGDET_DC_REF_CH1_L (PCM186X_PAGE_BASE(0) + 64) +#define PCM186X_SIGDET_DC_DIFF_CH1_L (PCM186X_PAGE_BASE(0) + 65) +#define PCM186X_SIGDET_DC_LEV_CH1_L (PCM186X_PAGE_BASE(0) + 66) +#define PCM186X_SIGDET_DC_REF_CH1_R (PCM186X_PAGE_BASE(0) + 67) +#define PCM186X_SIGDET_DC_DIFF_CH1_R (PCM186X_PAGE_BASE(0) + 68) +#define PCM186X_SIGDET_DC_LEV_CH1_R (PCM186X_PAGE_BASE(0) + 69) +#define PCM186X_SIGDET_DC_REF_CH2_L (PCM186X_PAGE_BASE(0) + 70) +#define PCM186X_SIGDET_DC_DIFF_CH2_L (PCM186X_PAGE_BASE(0) + 71) +#define PCM186X_SIGDET_DC_LEV_CH2_L (PCM186X_PAGE_BASE(0) + 72) +#define PCM186X_SIGDET_DC_REF_CH2_R (PCM186X_PAGE_BASE(0) + 73) +#define PCM186X_SIGDET_DC_DIFF_CH2_R (PCM186X_PAGE_BASE(0) + 74) +#define PCM186X_SIGDET_DC_LEV_CH2_R (PCM186X_PAGE_BASE(0) + 75) +#define PCM186X_SIGDET_DC_REF_CH3_L (PCM186X_PAGE_BASE(0) + 76) +#define PCM186X_SIGDET_DC_DIFF_CH3_L (PCM186X_PAGE_BASE(0) + 77) +#define PCM186X_SIGDET_DC_LEV_CH3_L (PCM186X_PAGE_BASE(0) + 78) +#define PCM186X_SIGDET_DC_REF_CH3_R (PCM186X_PAGE_BASE(0) + 79) +#define PCM186X_SIGDET_DC_DIFF_CH3_R (PCM186X_PAGE_BASE(0) + 80) +#define PCM186X_SIGDET_DC_LEV_CH3_R (PCM186X_PAGE_BASE(0) + 81) +#define PCM186X_SIGDET_DC_REF_CH4_L (PCM186X_PAGE_BASE(0) + 82) +#define PCM186X_SIGDET_DC_DIFF_CH4_L (PCM186X_PAGE_BASE(0) + 83) +#define PCM186X_SIGDET_DC_LEV_CH4_L (PCM186X_PAGE_BASE(0) + 84) +#define PCM186X_SIGDET_DC_REF_CH4_R (PCM186X_PAGE_BASE(0) + 85) +#define PCM186X_SIGDET_DC_DIFF_CH4_R (PCM186X_PAGE_BASE(0) + 86) +#define PCM186X_SIGDET_DC_LEV_CH4_R (PCM186X_PAGE_BASE(0) + 87) +#define PCM186X_AUXADC_DATA_CTRL (PCM186X_PAGE_BASE(0) + 88) +#define PCM186X_AUXADC_DATA_LSB (PCM186X_PAGE_BASE(0) + 89) +#define PCM186X_AUXADC_DATA_MSB (PCM186X_PAGE_BASE(0) + 90) +#define PCM186X_INT_ENABLE (PCM186X_PAGE_BASE(0) + 96) +#define PCM186X_INT_FLAG (PCM186X_PAGE_BASE(0) + 97) +#define PCM186X_INT_POL_WIDTH (PCM186X_PAGE_BASE(0) + 98) +#define PCM186X_POWER_CTRL (PCM186X_PAGE_BASE(0) + 112) +#define PCM186X_FILTER_MUTE_CTRL (PCM186X_PAGE_BASE(0) + 113) +#define PCM186X_DEVICE_STATUS (PCM186X_PAGE_BASE(0) + 114) +#define PCM186X_FSAMPLE_STATUS (PCM186X_PAGE_BASE(0) + 115) +#define PCM186X_DIV_STATUS (PCM186X_PAGE_BASE(0) + 116) +#define PCM186X_CLK_STATUS (PCM186X_PAGE_BASE(0) + 117) +#define PCM186X_SUPPLY_STATUS (PCM186X_PAGE_BASE(0) + 120) + +/* Register Definitions - Page 1 */ +#define PCM186X_MMAP_STAT_CTRL (PCM186X_PAGE_BASE(1) + 1) +#define PCM186X_MMAP_ADDRESS (PCM186X_PAGE_BASE(1) + 2) +#define PCM186X_MEM_WDATA0 (PCM186X_PAGE_BASE(1) + 4) +#define PCM186X_MEM_WDATA1 (PCM186X_PAGE_BASE(1) + 5) +#define PCM186X_MEM_WDATA2 (PCM186X_PAGE_BASE(1) + 6) +#define PCM186X_MEM_WDATA3 (PCM186X_PAGE_BASE(1) + 7) +#define PCM186X_MEM_RDATA0 (PCM186X_PAGE_BASE(1) + 8) +#define PCM186X_MEM_RDATA1 (PCM186X_PAGE_BASE(1) + 9) +#define PCM186X_MEM_RDATA2 (PCM186X_PAGE_BASE(1) + 10) +#define PCM186X_MEM_RDATA3 (PCM186X_PAGE_BASE(1) + 11) + +/* Register Definitions - Page 3 */ +#define PCM186X_OSC_PWR_DOWN_CTRL (PCM186X_PAGE_BASE(3) + 18) +#define PCM186X_MIC_BIAS_CTRL (PCM186X_PAGE_BASE(3) + 21) + +/* Register Definitions - Page 253 */ +#define PCM186X_CURR_TRIM_CTRL (PCM186X_PAGE_BASE(253) + 20) + +#define PCM186X_MAX_REGISTER PCM186X_CURR_TRIM_CTRL + +/* + * Register definitions for DSP accessed indirectly through PCM186X_MEM_X using + * a special sequence. Each of the registers holds 24 bits. See device data + * sheet for details. + */ +#define PCM186X_DSP_MIX1_CH1L 0x00 +#define PCM186X_DSP_MIX1_CH1R 0x01 +#define PCM186X_DSP_MIX1_CH2L 0x02 +#define PCM186X_DSP_MIX1_CH2R 0x03 +#define PCM186X_DSP_MIX1_I2SL 0x04 +#define PCM186X_DSP_MIX1_I2SR 0x05 +#define PCM186X_DSP_MIX2_CH1L 0x06 +#define PCM186X_DSP_MIX2_CH1R 0x07 +#define PCM186X_DSP_MIX2_CH2L 0x08 +#define PCM186X_DSP_MIX2_CH2R 0x09 +#define PCM186X_DSP_MIX2_I2SL 0x0a +#define PCM186X_DSP_MIX2_I2SR 0x0b +#define PCM186X_DSP_MIX3_CH1L 0x0c +#define PCM186X_DSP_MIX3_CH1R 0x0d +#define PCM186X_DSP_MIX3_CH2L 0x0e +#define PCM186X_DSP_MIX3_CH2R 0x0f +#define PCM186X_DSP_MIX3_I2SL 0x10 +#define PCM186X_DSP_MIX3_I2SR 0x11 +#define PCM186X_DSP_MIX4_CH1L 0x12 +#define PCM186X_DSP_MIX4_CH1R 0x13 +#define PCM186X_DSP_MIX4_CH2L 0x14 +#define PCM186X_DSP_MIX4_CH2R 0x15 +#define PCM186X_DSP_MIX4_I2SL 0x16 +#define PCM186X_DSP_MIX4_I2SR 0x17 +#define PCM186X_DSP_LPF_B0 0x20 +#define PCM186X_DSP_LPF_B1 0x21 +#define PCM186X_DSP_LPF_B2 0x22 +#define PCM186X_DSP_LPF_A1 0x23 +#define PCM186X_DSP_LPF_A2 0x24 +#define PCM186X_DSP_HPF_B0 0x25 +#define PCM186X_DSP_HPF_B1 0x26 +#define PCM186X_DSP_HPF_B2 0x27 +#define PCM186X_DSP_HPF_A1 0x28 +#define PCM186X_DSP_HPF_A2 0x29 +#define PCM186X_DSP_LOSS_THRESH 0x2c +#define PCM186X_DSP_RES_THRESH 0x2d + +/* PCM186X_PAGE */ +#define PCM186X_PAGE_0 0x00 +#define PCM186X_PAGE_1 0x01 +#define PCM186X_PAGE_3 0x03 +#define PCM186X_RESET 0xff + +/* PCM186X_ADCX_INPUT_SEL_X */ +#define PCM186X_ADC_INPUT_SEL_POL BIT(7) +#define PCM186X_ADC_INPUT_SEL_MASK GENMASK(5, 0) + +/* PCM186X_PCM_CFG */ +#define PCM186X_PCM_CFG_RX_WLEN_32 (0x0 << 6) +#define PCM186X_PCM_CFG_RX_WLEN_24 (0x1 << 6) +#define PCM186X_PCM_CFG_RX_WLEN_20 (0x2 << 6) +#define PCM186X_PCM_CFG_RX_WLEN_16 (0x3 << 6) +#define PCM186X_PCM_CFG_RX_WLEN_MASK GENMASK(7, 6) +#define PCM186X_PCM_CFG_TDM_LRCK_MODE BIT(4) +#define PCM186X_PCM_CFG_TX_WLEN_32 (0x0 << 2) +#define PCM186X_PCM_CFG_TX_WLEN_24 (0x1 << 2) +#define PCM186X_PCM_CFG_TX_WLEN_20 (0x2 << 2) +#define PCM186X_PCM_CFG_TX_WLEN_16 (0x3 << 2) +#define PCM186X_PCM_CFG_TX_WLEN_MASK GENMASK(3, 2) +#define PCM186X_PCM_CFG_FMT_I2S 0x00 +#define PCM186X_PCM_CFG_FMT_LEFTJ 0x01 +#define PCM186X_PCM_CFG_FMT_RIGHTJ 0x02 +#define PCM186X_PCM_CFG_FMT_TDM 0x03 +#define PCM186X_PCM_CFG_FMT_MASK GENMASK(1, 0) + +/* PCM186X_TDM_TX_SEL */ +#define PCM186X_TDM_TX_SEL_2CH 0x00 +#define PCM186X_TDM_TX_SEL_4CH 0x01 +#define PCM186X_TDM_TX_SEL_6CH 0x02 +#define PCM186X_TDM_TX_SEL_MASK 0x03 + +/* PCM186X_CLK_CTRL */ +#define PCM186X_CLK_CTRL_SCK_XI_SEL1 BIT(7) +#define PCM186X_CLK_CTRL_SCK_XI_SEL0 BIT(6) +#define PCM186X_CLK_CTRL_SCK_SRC_PLL BIT(5) +#define PCM186X_CLK_CTRL_MST_MODE BIT(4) +#define PCM186X_CLK_CTRL_ADC_SRC_PLL BIT(3) +#define PCM186X_CLK_CTRL_DSP2_SRC_PLL BIT(2) +#define PCM186X_CLK_CTRL_DSP1_SRC_PLL BIT(1) +#define PCM186X_CLK_CTRL_CLKDET_EN BIT(0) + +/* PCM186X_PLL_CTRL */ +#define PCM186X_PLL_CTRL_LOCK BIT(4) +#define PCM186X_PLL_CTRL_REF_SEL BIT(1) +#define PCM186X_PLL_CTRL_EN BIT(0) + +/* PCM186X_POWER_CTRL */ +#define PCM186X_PWR_CTRL_PWRDN BIT(2) +#define PCM186X_PWR_CTRL_SLEEP BIT(1) +#define PCM186X_PWR_CTRL_STBY BIT(0) + +/* PCM186X_CLK_STATUS */ +#define PCM186X_CLK_STATUS_LRCKHLT BIT(6) +#define PCM186X_CLK_STATUS_BCKHLT BIT(5) +#define PCM186X_CLK_STATUS_SCKHLT BIT(4) +#define PCM186X_CLK_STATUS_LRCKERR BIT(2) +#define PCM186X_CLK_STATUS_BCKERR BIT(1) +#define PCM186X_CLK_STATUS_SCKERR BIT(0) + +/* PCM186X_SUPPLY_STATUS */ +#define PCM186X_SUPPLY_STATUS_DVDD BIT(2) +#define PCM186X_SUPPLY_STATUS_AVDD BIT(1) +#define PCM186X_SUPPLY_STATUS_LDO BIT(0) + +/* PCM186X_MMAP_STAT_CTRL */ +#define PCM186X_MMAP_STAT_DONE BIT(4) +#define PCM186X_MMAP_STAT_BUSY BIT(2) +#define PCM186X_MMAP_STAT_R_REQ BIT(1) +#define PCM186X_MMAP_STAT_W_REQ BIT(0) + +extern const struct dev_pm_ops pcm186x_pm_ops; +extern const struct regmap_config pcm186x_regmap; + +int pcm186x_probe(struct device *dev, enum pcm186x_type type, int irq, + struct regmap *regmap); +int pcm186x_remove(struct device *dev); + +#endif /* _PCM186X_H_ */
On Fri, Nov 10, 2017 at 01:57:11PM -0600, Andrew F. Davis wrote:
This looks mostly good, a few small issues though:
- dev_info(&i2c->dev, "%s() i2c->addr=%d\n", __func__, i2c->addr);
No need for this as standard, we already have I2C level logging facilities if they're really needed. It's OK to do things like log chip revisions read back from hardware but this is pure software.
+static const struct snd_kcontrol_new pcm1863_snd_controls[] = {
- SOC_DOUBLE_R_S_TLV("Analog Gain", PCM186X_PGA_VAL_CH1_L,
Volume controls should end in Volume to tell userspace how to handle them, see ControlNames.txt.
- ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(priv->supplies),
priv->supplies);
- if (ret != 0) {
dev_err(dev, "failed to request supplies: %d\n", ret);
return ret;
- }
- /* Reset device registers for a consistent power-on like state */
- ret = regmap_write(regmap, PCM186X_PAGE, PCM186X_RESET);
- if (ret != 0) {
dev_err(dev, "failed to write device: %d\n", ret);
return ret;
- }
We didn't enable the supplies for the device before we reset it, if the device was powered off then the write will hopefully not work and we'll get a spurious error here. The driver should bounce the supplies on at least long enough to do the reset, it's not ideal but it's robust.
On Fri, Nov 10, 2017 at 01:57:10PM -0600, Andrew F. Davis wrote:
Add the dt-binding documentation for the TI PCM186x 2ch and 4ch Audio ADCs With Universal Front End.
Signed-off-by: Andrew F. Davis afd@ti.com
.../devicetree/bindings/sound/pcm186x.txt | 42 ++++++++++++++++++++++ 1 file changed, 42 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/pcm186x.txt
diff --git a/Documentation/devicetree/bindings/sound/pcm186x.txt b/Documentation/devicetree/bindings/sound/pcm186x.txt new file mode 100644 index 000000000000..0bc7d265c7bd --- /dev/null +++ b/Documentation/devicetree/bindings/sound/pcm186x.txt @@ -0,0 +1,42 @@ +Texas Instruments PCM186x Universal Audio ADC
+These devices support both I2C and SPI (configured with pin strapping +on the board).
+Required properties:
- compatible : "ti,pcm1862",
"ti,pcm1863",
"ti,pcm1864",
"ti,pcm1865"
- reg : The I2C address of the device for I2C, the chip select
number for SPI.
- avdd-supply: Analog core power supply (3.3v)
- dvdd-supply: Digital core power supply
- iovdd-supply: Digital IO power supply
See regulator/regulator.txt for more information
+CODEC input pins:
- VINL1
- VINR1
- VINL2
- VINR2
- VINL3
- VINR3
- VINL4
- VINR4
+The pins can be used in referring sound node's audio-routing property.
+Example:
- pcm186x: pcm186x@4a {
audio-codec@4a
With that,
Acked-by: Rob Herring robh@kernel.org
compatible = "ti,pcm1865";
reg = <0x4a>;
avdd-supply = <®_3v3_analog>;
dvdd-supply = <®_3v3>;
iovdd-supply = <®_1v8>;
- };
-- 2.15.0
participants (3)
-
Andrew F. Davis
-
Mark Brown
-
Rob Herring