Signed-off-by: Anatol Pomozov anatol.pomozov@gmail.com --- .../devicetree/bindings/sound/nau8825.txt | 68 ++ sound/soc/codecs/Kconfig | 4 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/nau8825.c | 944 +++++++++++++++++++++ sound/soc/codecs/nau8825.h | 276 ++++++ 5 files changed, 1294 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/nau8825.txt create mode 100644 sound/soc/codecs/nau8825.c create mode 100644 sound/soc/codecs/nau8825.h

diff --git a/Documentation/devicetree/bindings/sound/nau8825.txt b/Documentation/devicetree/bindings/sound/nau8825.txt new file mode 100644 index 0000000..46e1868 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nau8825.txt @@ -0,0 +1,68 @@ +Nuvoton NAU8825 audio codec + +This device supports I2C only. + +Required properties: + - compatible : Must be "nuvoton,nau8825" + + - reg : the I2C address of the device. This is either 0x1a (CSB=0) or 0x1b (CSB=1). + +Optional properties: + - nuvoton,jkdet-pullup: Pull-up JKDET pin. Boolean. + + - nuvoton,micbias-voltage: Micbias voltage level. + 0 - VDDA + 1 - VDDA + 2 - VDDA * 1.1 + 3 - VDDA * 1.2 + 4 - VDDA * 1.3 + 5 - VDDA * 1.4 + 6 - VDDA * 1.53 + 7 - VDDA * 1.53 + + - nuvoton,sar-threshold-num: Number of buttons supported + - nuvoton,sar-threshold: Impedance threshold for each button. Array that contains up to 8 buttons configuration. SAR value is calculated as + SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R) + where MICBIAS is configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by 'nuvoton,sar-voltage', R - button impedance. + Refer datasheet section 10.2 for more information about threshold calculation. + + - nuvoton,sar-hysteresis: Button impedance measurement hysteresis. + + - nuvoton,sar-voltage: Reference voltage for button impedance measurement. + 0 - VDDA + 1 - VDDA + 2 - VDDA * 1.1 + 3 - VDDA * 1.2 + 4 - VDDA * 1.3 + 5 - VDDA * 1.4 + 6 - VDDA * 1.53 + 7 - VDDA * 1.53 + + - nuvoton,short-key-debounce: Button short key press debounce time. + 0 - 30ms + 1 - 50ms + 2 - 100ms + 3 - 30ms + + - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms + - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms + + +Example: + + headset: nau8825@1a { + compatible = "nuvoton,nau8825"; + reg = <0x1a>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(E, 6) IRQ_TYPE_LEVEL_LOW>; + nuvoton,jkdet-pullup; + nuvoton,micbias-voltage = <6>; + // Setup 4 buttons impedane according to Android specification + nuvoton,sar-threshold-num = <4>; + nuvoton,sar-threshold = <0x14 0x29 0x40 0x78>; + nuvoton,sar-hysteresis = <1>; + nuvoton,sar-voltage = <0>; + nuvoton,short-key-debounce = <2>; + nuvoton,jack-insert-debounce = <7>; + nuvoton,jack-eject-debounce = <7>; + }; diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 7fcbc22..1a3639c 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -78,6 +78,7 @@ config SND_SOC_ALL_CODECS select SND_SOC_MAX9877 if I2C select SND_SOC_MC13783 if MFD_MC13XXX select SND_SOC_ML26124 if I2C + select SND_SOC_NAU8825 if I2C select SND_SOC_HDMI_CODEC select SND_SOC_PCM1681 if I2C select SND_SOC_PCM1792A if SPI_MASTER @@ -892,6 +893,9 @@ config SND_SOC_MC13783 config SND_SOC_ML26124 tristate

+config SND_SOC_NAU8825 + tristate + config SND_SOC_TPA6130A2 tristate "Texas Instruments TPA6130A2 headphone amplifier" depends on I2C diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 5b46c8f..4874881 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -71,6 +71,7 @@ snd-soc-max98925-objs := max98925.o snd-soc-max9850-objs := max9850.o snd-soc-mc13783-objs := mc13783.o snd-soc-ml26124-objs := ml26124.o +snd-soc-nau8825-objs := nau8825.o snd-soc-hdmi-codec-objs := hdmi.o snd-soc-pcm1681-objs := pcm1681.o snd-soc-pcm1792a-codec-objs := pcm1792a.o @@ -262,6 +263,7 @@ obj-$(CONFIG_SND_SOC_MAX98925) += snd-soc-max98925.o obj-$(CONFIG_SND_SOC_MAX9850) += snd-soc-max9850.o obj-$(CONFIG_SND_SOC_MC13783) += snd-soc-mc13783.o obj-$(CONFIG_SND_SOC_ML26124) += snd-soc-ml26124.o +obj-$(CONFIG_SND_SOC_NAU8825) += snd-soc-nau8825.o obj-$(CONFIG_SND_SOC_HDMI_CODEC) += snd-soc-hdmi-codec.o obj-$(CONFIG_SND_SOC_PCM1681) += snd-soc-pcm1681.o obj-$(CONFIG_SND_SOC_PCM1792A) += snd-soc-pcm1792a-codec.o diff --git a/sound/soc/codecs/nau8825.c b/sound/soc/codecs/nau8825.c new file mode 100644 index 0000000..96eed3a --- /dev/null +++ b/sound/soc/codecs/nau8825.c @@ -0,0 +1,944 @@ +/* + * Nuvoton NAU8825 audio codec driver + * + * Copyright 2015 Google Chromium project. + * Author: Anatol Pomozov anatol@chromium.org + * Copyright 2015 Nuvoton Technology Corp. + * Co-author: Meng-Huang Kuo mhkuo@nuvoton.com + * + * Licensed under the GPL-2. + */ + +#include <linux/module.h> +#include <linux/delay.h> +#include <linux/init.h> +#include <linux/i2c.h> +#include <linux/regmap.h> +#include <linux/slab.h> +#include <sound/initval.h> +#include <sound/tlv.h> + +#include <sound/core.h> +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/jack.h> + +#include "nau8825.h" + +struct nau8825 { + struct device *dev; + struct regmap *regmap; + struct snd_soc_dapm_context *dapm; + int irq; + struct snd_soc_jack *jack; + int button_pressed; + int micbias_voltage; + bool jkdet_pullup; + int sar_threshold_num; + int sar_threshold[8]; + int sar_hysteresis; + int sar_voltage; + int key_debounce; + int jack_insert_debounce; + int jack_eject_debounce; +}; + +static const struct reg_default nau8825_reg_defaults[] = { + { NAU8825_REG_ENA_CTRL, 0x00ff }, + { NAU8825_REG_CLK_DIVIDER, 0x0050 }, + { NAU8825_REG_FLL1, 0x0 }, + { NAU8825_REG_FLL2, 0x3126 }, + { NAU8825_REG_FLL3, 0x0008 }, + { NAU8825_REG_FLL4, 0x0010 }, + { NAU8825_REG_FLL5, 0x0 }, + { NAU8825_REG_FLL6, 0x6000 }, + { NAU8825_REG_FLL_VCO_RSV, 0xf13c }, + { NAU8825_REG_HSD_CTRL, 0x000c }, + { NAU8825_REG_JACK_DET_CTRL, 0x0 }, + { NAU8825_REG_INTERRUPT_MASK, 0x0 }, + { NAU8825_REG_INTERRUPT_DIS_CTRL, 0xffff }, + { NAU8825_REG_SAR_CTRL, 0x0015 }, + { NAU8825_REG_KEYDET_CTRL, 0x0110 }, + { NAU8825_REG_VDET_THRESHOLD_1, 0x0 }, + { NAU8825_REG_VDET_THRESHOLD_2, 0x0 }, + { NAU8825_REG_VDET_THRESHOLD_3, 0x0 }, + { NAU8825_REG_VDET_THRESHOLD_4, 0x0 }, + { NAU8825_REG_GPIO34_CTRL, 0x0 }, + { NAU8825_REG_GPIO12_CTRL, 0x0 }, + { NAU8825_REG_TDM_CTRL, 0x0 }, + { NAU8825_REG_I2S_PCM_CTRL1, 0x000b }, + { NAU8825_REG_I2S_PCM_CTRL2, 0x8010 }, + { NAU8825_REG_LEFT_TIME_SLOT, 0x0 }, + { NAU8825_REG_RIGHT_TIME_SLOT, 0x0 }, + { NAU8825_REG_BIQ_CTRL, 0x0 }, + { NAU8825_REG_BIQ_COF1, 0x0 }, + { NAU8825_REG_BIQ_COF2, 0x0 }, + { NAU8825_REG_BIQ_COF3, 0x0 }, + { NAU8825_REG_BIQ_COF4, 0x0 }, + { NAU8825_REG_BIQ_COF5, 0x0 }, + { NAU8825_REG_BIQ_COF6, 0x0 }, + { NAU8825_REG_BIQ_COF7, 0x0 }, + { NAU8825_REG_BIQ_COF8, 0x0 }, + { NAU8825_REG_BIQ_COF9, 0x0 }, + { NAU8825_REG_BIQ_COF10, 0x0 }, + { NAU8825_REG_ADC_RATE, 0x0010 }, + { NAU8825_REG_DAC_CTRL1, 0x0001 }, + { NAU8825_REG_DAC_CTRL2, 0x0 }, + { NAU8825_REG_DAC_DGAIN_CTRL, 0x0 }, + { NAU8825_REG_ADC_DGAIN_CTRL, 0x00cf }, + { NAU8825_REG_MUTE_CTRL, 0x0 }, + { NAU8825_REG_HSVOL_CTRL, 0x0 }, + { NAU8825_REG_DACL_CTRL, 0x02cf }, + { NAU8825_REG_DACR_CTRL, 0x00cf }, + { NAU8825_REG_ADC_DRC_KNEE_IP12, 0x1486 }, + { NAU8825_REG_ADC_DRC_KNEE_IP34, 0x0f12 }, + { NAU8825_REG_ADC_DRC_SLOPES, 0x25ff }, + { NAU8825_REG_ADC_DRC_ATKDCY, 0x3457 }, + { NAU8825_REG_DAC_DRC_KNEE_IP12, 0x1486 }, + { NAU8825_REG_DAC_DRC_KNEE_IP34, 0x0f12 }, + { NAU8825_REG_DAC_DRC_SLOPES, 0x25f9 }, + { NAU8825_REG_DAC_DRC_ATKDCY, 0x3457 }, + { NAU8825_REG_IMM_MODE_CTRL, 0x0 }, + { NAU8825_REG_CLASSG_CTRL, 0x0 }, + { NAU8825_REG_OPT_EFUSE_CTRL, 0x0 }, + { NAU8825_REG_MISC_CTRL, 0x0 }, + { NAU8825_REG_BIAS_ADJ, 0x0 }, + { NAU8825_REG_TRIM_SETTINGS, 0x0 }, + { NAU8825_REG_ANALOG_CONTROL_1, 0x0 }, + { NAU8825_REG_ANALOG_CONTROL_2, 0x0 }, + { NAU8825_REG_ANALOG_ADC_1, 0x0011 }, + { NAU8825_REG_ANALOG_ADC_2, 0x0020 }, + { NAU8825_REG_RDAC, 0x0008 }, + { NAU8825_REG_MIC_BIAS, 0x0006 }, + { NAU8825_REG_BOOST, 0x0 }, + { NAU8825_REG_FEPGA, 0x0 }, + { NAU8825_REG_POWER_UP_CONTROL, 0x0 }, + { NAU8825_REG_CHARGE_PUMP, 0x0 }, +}; + +static bool nau8825_readable_reg(struct device *dev, unsigned int reg) +{ + switch (reg) { + case NAU8825_REG_ENA_CTRL: + case NAU8825_REG_CLK_DIVIDER ... NAU8825_REG_FLL_VCO_RSV: + case NAU8825_REG_HSD_CTRL ... NAU8825_REG_JACK_DET_CTRL: + case NAU8825_REG_INTERRUPT_MASK ... NAU8825_REG_KEYDET_CTRL: + case NAU8825_REG_VDET_THRESHOLD_1 ... NAU8825_REG_DACR_CTRL: + case NAU8825_REG_ADC_DRC_KNEE_IP12 ... NAU8825_REG_ADC_DRC_ATKDCY: + case NAU8825_REG_DAC_DRC_KNEE_IP12 ... NAU8825_REG_DAC_DRC_ATKDCY: + case NAU8825_REG_IMM_MODE_CTRL ... NAU8825_REG_IMM_RMS_R: + case NAU8825_REG_CLASSG_CTRL ... NAU8825_REG_OPT_EFUSE_CTRL: + case NAU8825_REG_MISC_CTRL: + case NAU8825_REG_I2C_DEVICE_ID ... NAU8825_REG_SARDOUT_RAM_STATUS: + case NAU8825_REG_BIAS_ADJ: + case NAU8825_REG_TRIM_SETTINGS ... NAU8825_REG_ANALOG_CONTROL_2: + case NAU8825_REG_ANALOG_ADC_1 ... NAU8825_REG_MIC_BIAS: + case NAU8825_REG_BOOST ... NAU8825_REG_FEPGA: + case NAU8825_REG_POWER_UP_CONTROL ... NAU8825_REG_GENERAL_STATUS: + return true; + default: + return false; + } + +} + +static bool nau8825_writeable_reg(struct device *dev, unsigned int reg) +{ + switch (reg) { + case NAU8825_REG_RESET ... NAU8825_REG_ENA_CTRL: + case NAU8825_REG_CLK_DIVIDER ... NAU8825_REG_FLL_VCO_RSV: + case NAU8825_REG_HSD_CTRL ... NAU8825_REG_JACK_DET_CTRL: + case NAU8825_REG_INTERRUPT_MASK: + case NAU8825_REG_INT_CLR_KEY_STATUS ... NAU8825_REG_KEYDET_CTRL: + case NAU8825_REG_VDET_THRESHOLD_1 ... NAU8825_REG_DACR_CTRL: + case NAU8825_REG_ADC_DRC_KNEE_IP12 ... NAU8825_REG_ADC_DRC_ATKDCY: + case NAU8825_REG_DAC_DRC_KNEE_IP12 ... NAU8825_REG_DAC_DRC_ATKDCY: + case NAU8825_REG_IMM_MODE_CTRL: + case NAU8825_REG_CLASSG_CTRL ... NAU8825_REG_OPT_EFUSE_CTRL: + case NAU8825_REG_MISC_CTRL: + case NAU8825_REG_BIAS_ADJ: + case NAU8825_REG_TRIM_SETTINGS ... NAU8825_REG_ANALOG_CONTROL_2: + case NAU8825_REG_ANALOG_ADC_1 ... NAU8825_REG_MIC_BIAS: + case NAU8825_REG_BOOST ... NAU8825_REG_FEPGA: + case NAU8825_REG_POWER_UP_CONTROL ... NAU8825_REG_CHARGE_PUMP: + return true; + default: + return false; + } +} + +static bool nau8825_volatile_reg(struct device *dev, unsigned int reg) +{ + switch (reg) { + case NAU8825_REG_RESET: + case NAU8825_REG_IRQ_STATUS: + case NAU8825_REG_INT_CLR_KEY_STATUS: + case NAU8825_REG_IMM_RMS_L: + case NAU8825_REG_IMM_RMS_R: + case NAU8825_REG_I2C_DEVICE_ID: + case NAU8825_REG_SARDOUT_RAM_STATUS: + case NAU8825_REG_CHARGE_PUMP_INPUT_READ: + case NAU8825_REG_GENERAL_STATUS: + return true; + default: + return false; + } +} + +static const char * const nau8825_adc_decimation[] = { + "32", "64", "128", "256" +}; + +static const struct soc_enum nau8825_adc_decimation_enum = + SOC_ENUM_SINGLE(NAU8825_REG_ADC_RATE, NAU8825_ADC_SYNC_DOWN_SFT, + ARRAY_SIZE(nau8825_adc_decimation), nau8825_adc_decimation); + +static const char * const nau8825_dac_oversampl[] = { + "64", "256", "128", "", "32" +}; + +static const struct soc_enum nau8825_dac_oversampl_enum = + SOC_ENUM_SINGLE(NAU8825_REG_DAC_CTRL1, NAU8825_DAC_OVERSAMPLE_SFT, + ARRAY_SIZE(nau8825_dac_oversampl), nau8825_dac_oversampl); + +static const DECLARE_TLV_DB_MINMAX_MUTE(adc_vol_tlv, -10300, 2400); +static const DECLARE_TLV_DB_MINMAX_MUTE(sidetone_vol_tlv, -4200, 0); +static const DECLARE_TLV_DB_MINMAX(dac_vol_tlv, -5400, 0); +static const DECLARE_TLV_DB_MINMAX(fepga_gain_tlv, -100, 3600); + +static const struct snd_kcontrol_new nau8825_controls[] = { + SOC_SINGLE_TLV("MIC Volume", NAU8825_REG_ADC_DGAIN_CTRL, + 0, 0xff, 0, adc_vol_tlv), + SOC_DOUBLE_TLV("HP Sidetone Volume", NAU8825_REG_ADC_DGAIN_CTRL, + 12, 8, 0x0f, 0, sidetone_vol_tlv), + SOC_DOUBLE_TLV("HP Volume", NAU8825_REG_HSVOL_CTRL, + 6, 0, 0x3f, 1, dac_vol_tlv), + SOC_SINGLE_TLV("Frontend PGA Gain", NAU8825_REG_POWER_UP_CONTROL, + 8, 37, 0, fepga_gain_tlv), + + SOC_ENUM("ADC Decimation Rate", nau8825_adc_decimation_enum), + SOC_ENUM("DAC Oversampling Rate", nau8825_dac_oversampl_enum), +}; + +/* DAC Mux 0x33[9] and 0x34[9] */ +static const char * const nau8825_dac_src[] = { + "DACL", "DACR", +}; + +static SOC_ENUM_SINGLE_DECL( + nau8825_dacl_enum, NAU8825_REG_DACL_CTRL, + NAU8825_DACL_CH_SEL_SFT, nau8825_dac_src); + +static SOC_ENUM_SINGLE_DECL( + nau8825_dacr_enum, NAU8825_REG_DACR_CTRL, + NAU8825_DACR_CH_SEL_SFT, nau8825_dac_src); + +static const struct snd_kcontrol_new nau8825_dacl_mux = + SOC_DAPM_ENUM("DACL Source", nau8825_dacl_enum); + +static const struct snd_kcontrol_new nau8825_dacr_mux = + SOC_DAPM_ENUM("DACR Source", nau8825_dacr_enum); + + +static const struct snd_soc_dapm_widget nau8825_dapm_widgets[] = { + SND_SOC_DAPM_AIF_OUT("AIFTX", "Capture", 0, NAU8825_REG_I2S_PCM_CTRL2, + 15, 1), + + SND_SOC_DAPM_INPUT("MIC"), + SND_SOC_DAPM_MICBIAS("MICBIAS", NAU8825_REG_MIC_BIAS, 8, 0), + + SND_SOC_DAPM_PGA("Frontend PGA", NAU8825_REG_POWER_UP_CONTROL, 14, 0, + NULL, 0), + + SND_SOC_DAPM_ADC("ADC", NULL, NAU8825_REG_ENA_CTRL, 8, 0), + SND_SOC_DAPM_SUPPLY("ADC Clock", NAU8825_REG_ENA_CTRL, 7, 0, NULL, 0), + SND_SOC_DAPM_SUPPLY("ADC Power", NAU8825_REG_ANALOG_ADC_2, 6, 0, NULL, + 0), + + /* ADC for button press detection */ + SND_SOC_DAPM_ADC("SAR", NULL, NAU8825_REG_SAR_CTRL, + NAU8825_SAR_ADC_EN_SFT, 0), + + SND_SOC_DAPM_DAC("ADACL", NULL, NAU8825_REG_RDAC, 12, 0), + SND_SOC_DAPM_DAC("ADACR", NULL, NAU8825_REG_RDAC, 13, 0), + SND_SOC_DAPM_SUPPLY("ADACL Clock", NAU8825_REG_RDAC, 8, 0, NULL, 0), + SND_SOC_DAPM_SUPPLY("ADACR Clock", NAU8825_REG_RDAC, 9, 0, NULL, 0), + + SND_SOC_DAPM_DAC("DDACR", NULL, NAU8825_REG_ENA_CTRL, + NAU8825_ENABLE_DACR_SFT, 0), + SND_SOC_DAPM_DAC("DDACL", NULL, NAU8825_REG_ENA_CTRL, + NAU8825_ENABLE_DACL_SFT, 0), + SND_SOC_DAPM_SUPPLY("DDAC Clock", NAU8825_REG_ENA_CTRL, 6, 0, NULL, 0), + + SND_SOC_DAPM_MUX("DACL Mux", SND_SOC_NOPM, 0, 0, &nau8825_dacl_mux), + SND_SOC_DAPM_MUX("DACR Mux", SND_SOC_NOPM, 0, 0, &nau8825_dacr_mux), + + SND_SOC_DAPM_PGA("HP amp L", NAU8825_REG_CLASSG_CTRL, 1, 0, NULL, 0), + SND_SOC_DAPM_PGA("HP amp R", NAU8825_REG_CLASSG_CTRL, 2, 0, NULL, 0), + SND_SOC_DAPM_SUPPLY("HP amp power", NAU8825_REG_CLASSG_CTRL, 0, 0, NULL, + 0), + + SND_SOC_DAPM_SUPPLY("Change Pump", NAU8825_REG_CHARGE_PUMP, 5, 0, NULL, + 0), + + SND_SOC_DAPM_SUPPLY("DACL Power", NAU8825_REG_CHARGE_PUMP, 8, 1, NULL, + 0), + SND_SOC_DAPM_SUPPLY("DACR Power", NAU8825_REG_CHARGE_PUMP, 9, 1, NULL, + 0), + + SND_SOC_DAPM_OUT_DRV("Output Driver R Stage 1", + NAU8825_REG_POWER_UP_CONTROL, 5, 0, NULL, 0), + SND_SOC_DAPM_OUT_DRV("Output Driver L Stage 1", + NAU8825_REG_POWER_UP_CONTROL, 4, 0, NULL, 0), + SND_SOC_DAPM_OUT_DRV("Output Driver R Stage 2", + NAU8825_REG_POWER_UP_CONTROL, 3, 0, NULL, 0), + SND_SOC_DAPM_OUT_DRV("Output Driver L Stage 2", + NAU8825_REG_POWER_UP_CONTROL, 2, 0, NULL, 0), + SND_SOC_DAPM_OUT_DRV("Output Driver R Stage 3", + NAU8825_REG_POWER_UP_CONTROL, 1, 0, NULL, 0), + SND_SOC_DAPM_OUT_DRV("Output Driver L Stage 3", + NAU8825_REG_POWER_UP_CONTROL, 0, 0, NULL, 0), + + SND_SOC_DAPM_OUTPUT("HPOL"), + SND_SOC_DAPM_OUTPUT("HPOR"), +}; + +static const struct snd_soc_dapm_route nau8825_dapm_routes[] = { + {"Frontend PGA", NULL, "MIC"}, + {"ADC", NULL, "Frontend PGA"}, + {"ADC", NULL, "ADC Clock"}, + {"ADC", NULL, "ADC Power"}, + {"AIFTX", NULL, "ADC"}, + + {"DDACL", NULL, "Playback"}, + {"DDACR", NULL, "Playback"}, + {"DDACL", NULL, "DDAC Clock"}, + {"DDACR", NULL, "DDAC Clock"}, + {"DDACL", NULL, "DACL Power"}, + {"DDACR", NULL, "DACR Power"}, + {"DACL Mux", "DACL", "DDACL"}, + {"DACL Mux", "DACR", "DDACR"}, + {"DACR Mux", "DACL", "DDACL"}, + {"DACR Mux", "DACR", "DDACR"}, + {"HP amp L", NULL, "Change Pump"}, + {"HP amp R", NULL, "Change Pump"}, + {"HP amp L", NULL, "DACL Mux"}, + {"HP amp R", NULL, "DACR Mux"}, + {"HP amp L", NULL, "HP amp power"}, + {"HP amp R", NULL, "HP amp power"}, + {"ADACL", NULL, "HP amp L"}, + {"ADACR", NULL, "HP amp R"}, + {"ADACL", NULL, "ADACL Clock"}, + {"ADACR", NULL, "ADACR Clock"}, + {"Output Driver L Stage 1", NULL, "ADACL"}, + {"Output Driver R Stage 1", NULL, "ADACR"}, + {"Output Driver L Stage 2", NULL, "Output Driver L Stage 1"}, + {"Output Driver R Stage 2", NULL, "Output Driver R Stage 1"}, + {"Output Driver L Stage 3", NULL, "Output Driver L Stage 2"}, + {"Output Driver R Stage 3", NULL, "Output Driver R Stage 2"}, + {"HPOL", NULL, "Output Driver L Stage 3"}, + {"HPOR", NULL, "Output Driver R Stage 3"}, +}; + +static int nau8825_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_codec *codec = dai->codec; + struct nau8825 *nau8825 = snd_soc_codec_get_drvdata(codec); + unsigned int val_len = 0; + + switch (params_width(params)) { + case 16: + val_len |= NAU8825_I2S_DL_16; + break; + case 20: + val_len |= NAU8825_I2S_DL_20; + break; + case 24: + val_len |= NAU8825_I2S_DL_24; + break; + case 32: + val_len |= NAU8825_I2S_DL_32; + break; + default: + return -EINVAL; + } + regmap_update_bits(nau8825->regmap, NAU8825_REG_I2S_PCM_CTRL1, + NAU8825_I2S_DL_MASK, val_len); + + return 0; +} + +static int nau8825_mute(struct snd_soc_dai *codec_dai, int mute) +{ + struct snd_soc_codec *codec = codec_dai->codec; + struct nau8825 *nau8825 = snd_soc_codec_get_drvdata(codec); + int reg_val; + + reg_val = mute ? NAU8825_HP_MUTE : 0; + regmap_update_bits(nau8825->regmap, NAU8825_REG_HSVOL_CTRL, + NAU8825_HP_MUTE, reg_val); + + return 0; +} + +static int nau8825_set_dai_fmt(struct snd_soc_dai *codec_dai, unsigned int fmt) +{ + struct snd_soc_codec *codec = codec_dai->codec; + struct nau8825 *nau8825 = snd_soc_codec_get_drvdata(codec); + unsigned int ctrl1_val = 0, ctrl2_val = 0; + + switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { + case SND_SOC_DAIFMT_CBM_CFM: + ctrl2_val |= NAU8825_I2S_MS_MASTER; + break; + case SND_SOC_DAIFMT_CBS_CFS: + break; + default: + return -EINVAL; + } + + switch (fmt & SND_SOC_DAIFMT_INV_MASK) { + case SND_SOC_DAIFMT_NB_NF: + break; + case SND_SOC_DAIFMT_IB_NF: + ctrl1_val |= NAU8825_I2S_BP_INV; + break; + default: + return -EINVAL; + } + + switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { + case SND_SOC_DAIFMT_I2S: + ctrl1_val |= NAU8825_I2S_DF_I2S; + break; + case SND_SOC_DAIFMT_LEFT_J: + ctrl1_val |= NAU8825_I2S_DF_LEFT; + break; + case SND_SOC_DAIFMT_RIGHT_J: + ctrl1_val |= NAU8825_I2S_DF_RIGTH; + break; + case SND_SOC_DAIFMT_DSP_A: + ctrl1_val |= NAU8825_I2S_DF_PCM_AB; + break; + case SND_SOC_DAIFMT_DSP_B: + ctrl1_val |= NAU8825_I2S_DF_PCM_AB; + ctrl1_val |= NAU8825_I2S_PCMB_EN; + break; + default: + return -EINVAL; + } + + regmap_update_bits(nau8825->regmap, NAU8825_REG_I2S_PCM_CTRL1, + NAU8825_I2S_DL_MASK | NAU8825_I2S_DF_MASK | + NAU8825_I2S_BP_MASK | NAU8825_I2S_PCMB_MASK, + ctrl1_val); + regmap_update_bits(nau8825->regmap, NAU8825_REG_I2S_PCM_CTRL2, + NAU8825_I2S_MS_MASK, ctrl2_val); + + return 0; +} + +static const struct snd_soc_dai_ops nau8825_dai_ops = { + .hw_params = nau8825_hw_params, + .digital_mute = nau8825_mute, + .set_fmt = nau8825_set_dai_fmt, +}; + +#define NAU8825_RATES SNDRV_PCM_RATE_8000_192000 +#define NAU8825_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE \ + | SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S32_LE) + +static struct snd_soc_dai_driver nau8825_dai = { + .name = "nau8825-hifi", + .playback = { + .stream_name = "Playback", + .channels_min = 1, + .channels_max = 2, + .rates = NAU8825_RATES, + .formats = NAU8825_FORMATS, + }, + .capture = { + .stream_name = "Capture", + .channels_min = 1, + .channels_max = 1, + .rates = NAU8825_RATES, + .formats = NAU8825_FORMATS, + }, + .ops = &nau8825_dai_ops, +}; + +/** + * nau8825_enable_jack_detect - Specify a jack for event reporting + * + * @component: component to register the jack with + * @jack: jack to use to report headset and button events on + * + * After this function has been called the headset insert/remove and button + * events will be routed to the given jack. Jack can be null to stop + * reporting. + */ +int nau8825_enable_jack_detect(struct snd_soc_codec *codec, + struct snd_soc_jack *jack) +{ + struct nau8825 *nau8825 = snd_soc_codec_get_drvdata(codec); + + nau8825->jack = jack; + + return 0; +} +EXPORT_SYMBOL_GPL(nau8825_enable_jack_detect); + + +static bool nau8825_is_jack_inserted(struct regmap *regmap) +{ + int status; + + regmap_read(regmap, NAU8825_REG_I2C_DEVICE_ID, &status); + return !(status & NAU8825_GPIO2JD1); +} + +static void nau8825_restart_jack_detection(struct regmap *regmap) +{ + /* this will restart the entire jack detection process including MIC/GND + * switching and create interrupts. We have to go from 0 to 1 and back + * to 0 to restart. + */ + regmap_update_bits(regmap, NAU8825_REG_JACK_DET_CTRL, + NAU8825_JACK_DET_RESTART, NAU8825_JACK_DET_RESTART); + regmap_update_bits(regmap, NAU8825_REG_JACK_DET_CTRL, + NAU8825_JACK_DET_RESTART, 0); +} + +static void nau8825_eject_jack(struct nau8825 *nau8825) +{ + struct snd_soc_dapm_context *dapm = nau8825->dapm; + struct regmap *regmap = nau8825->regmap; + + snd_soc_dapm_disable_pin(dapm, "SAR"); + snd_soc_dapm_disable_pin(dapm, "MICBIAS"); + /* Detach 2kOhm Resistors from MICBIAS to MICGND1/2 */ + regmap_update_bits(regmap, NAU8825_REG_MIC_BIAS, + NAU8825_MICBIAS_JKSLV | NAU8825_MICBIAS_JKR2, 0); + /* ground HPL/HPR, MICGRND1/2 */ + regmap_update_bits(regmap, NAU8825_REG_HSD_CTRL, 0xf, 0xf); + + snd_soc_dapm_sync(dapm); +} + +static int nau8825_button_decode(int value) +{ + int buttons; + + /* The chip supports up to 8 buttons, but ALSA defines only 6 buttons */ + if (value & BIT(0)) + buttons |= SND_JACK_BTN_0; + if (value & BIT(1)) + buttons |= SND_JACK_BTN_1; + if (value & BIT(2)) + buttons |= SND_JACK_BTN_2; + if (value & BIT(3)) + buttons |= SND_JACK_BTN_3; + if (value & BIT(4)) + buttons |= SND_JACK_BTN_4; + if (value & BIT(5)) + buttons |= SND_JACK_BTN_5; + + return buttons; +} + +static int nau8825_jack_insert(struct nau8825 *nau8825) +{ + struct regmap *regmap = nau8825->regmap; + struct snd_soc_dapm_context *dapm = nau8825->dapm; + int jack_status_reg, mic_detected; + int type; + + regmap_read(regmap, NAU8825_REG_GENERAL_STATUS, &jack_status_reg); + mic_detected = (jack_status_reg >> 10) & 3; + + switch (mic_detected) { + case 0: + /* no mic */ + type = SND_JACK_HEADPHONE; + break; + case 1: + dev_dbg(nau8825->dev, "OMTP (micgnd1) mic connected\n"); + type = SND_JACK_HEADSET; + + /* Unground MICGND1 */ + regmap_update_bits(regmap, NAU8825_REG_HSD_CTRL, 3 << 2, + 1 << 2); + /* Unground HPL/R */ + regmap_update_bits(regmap, NAU8825_REG_HSD_CTRL, 0x3, 0); + /* Attach 2kOhm Resistor from MICBIAS to MICGND1 */ + regmap_update_bits(regmap, NAU8825_REG_MIC_BIAS, + NAU8825_MICBIAS_JKSLV | NAU8825_MICBIAS_JKR2, + NAU8825_MICBIAS_JKR2); + /* Attach SARADC to MICGND1 */ + regmap_update_bits(regmap, NAU8825_REG_SAR_CTRL, + NAU8825_SAR_INPUT_MASK, + NAU8825_SAR_INPUT_JKR2); + + snd_soc_dapm_force_enable_pin(dapm, "MICBIAS"); + snd_soc_dapm_force_enable_pin(dapm, "SAR"); + snd_soc_dapm_sync(dapm); + break; + case 2: + case 3: + dev_dbg(nau8825->dev, "CTIA (micgnd2) mic connected\n"); + type = SND_JACK_HEADSET; + + /* Unground MICGND2 */ + regmap_update_bits(regmap, NAU8825_REG_HSD_CTRL, 3 << 2, + 2 << 2); + /* Unground HPL/R */ + regmap_update_bits(regmap, NAU8825_REG_HSD_CTRL, 0x3, 0); + /* Attach 2kOhm Resistor from MICBIAS to MICGND2 */ + regmap_update_bits(regmap, NAU8825_REG_MIC_BIAS, + NAU8825_MICBIAS_JKSLV | NAU8825_MICBIAS_JKR2, + NAU8825_MICBIAS_JKSLV); + /* Attach SARADC to MICGND2 */ + regmap_update_bits(regmap, NAU8825_REG_SAR_CTRL, + NAU8825_SAR_INPUT_MASK, + NAU8825_SAR_INPUT_JKSLV); + + snd_soc_dapm_force_enable_pin(dapm, "MICBIAS"); + snd_soc_dapm_force_enable_pin(dapm, "SAR"); + snd_soc_dapm_sync(dapm); + break; + } + + return type; +} + +#define NAU8825_BUTTONS (SND_JACK_BTN_0 | SND_JACK_BTN_1 | \ + SND_JACK_BTN_2 | SND_JACK_BTN_3) + +static irqreturn_t nau8825_interrupt(int irq, void *data) +{ + struct nau8825 *nau8825 = (struct nau8825 *)data; + struct regmap *regmap = nau8825->regmap; + int active_irq, clear_irq = 0, event = 0, event_mask = 0; + + regmap_read(regmap, NAU8825_REG_IRQ_STATUS, &active_irq); + + if ((active_irq & NAU8825_JACK_EJECTION_IRQ_MASK) == + NAU8825_JACK_EJECTION_DETECTED) { + + nau8825_eject_jack(nau8825); + event_mask |= SND_JACK_HEADSET; + clear_irq = NAU8825_JACK_EJECTION_IRQ_MASK; + } else if (active_irq & NAU8825_KEY_SHORT_PRESS_IRQ) { + int key_status; + + regmap_read(regmap, NAU8825_REG_INT_CLR_KEY_STATUS, + &key_status); + + /* upper 8 bits of the register are for short pressed keys, + lower 8 bits - for long pressed buttons */ + nau8825->button_pressed = nau8825_button_decode( + key_status >> 8); + + event |= nau8825->button_pressed; + event_mask |= NAU8825_BUTTONS; + clear_irq = NAU8825_KEY_SHORT_PRESS_IRQ; + } else if (active_irq & NAU8825_KEY_RELEASE_IRQ) { + event_mask = NAU8825_BUTTONS; + clear_irq = NAU8825_KEY_RELEASE_IRQ; + } else if (active_irq & NAU8825_HEADSET_COMPLETION_IRQ) { + if (nau8825_is_jack_inserted(regmap)) { + event |= nau8825_jack_insert(nau8825); + } else { + dev_warn(nau8825->dev, "Headset completion IRQ fired but no headset connected\n"); + nau8825_eject_jack(nau8825); + } + + event_mask |= SND_JACK_HEADSET; + clear_irq = NAU8825_HEADSET_COMPLETION_IRQ; + } + + if (!clear_irq) + clear_irq = active_irq; + /* clears the rightmost interruption */ + regmap_write(regmap, NAU8825_REG_INT_CLR_KEY_STATUS, clear_irq); + + if (event_mask) + snd_soc_jack_report(nau8825->jack, event, event_mask); + + return IRQ_HANDLED; +} + +static void nau8825_setup_buttons(struct nau8825 *nau8825) +{ + struct regmap *regmap = nau8825->regmap; + + regmap_update_bits(regmap, NAU8825_REG_SAR_CTRL, + NAU8825_SAR_TRACKING_GAIN_MASK, + nau8825->sar_voltage << NAU8825_SAR_TRACKING_GAIN_SFT); + + regmap_update_bits(regmap, NAU8825_REG_KEYDET_CTRL, + NAU8825_KEYDET_LEVELS_NR_MASK, + (nau8825->sar_threshold_num - 1) << NAU8825_KEYDET_LEVELS_NR_SFT); + regmap_update_bits(regmap, NAU8825_REG_KEYDET_CTRL, + NAU8825_KEYDET_HYSTERESIS_MASK, + nau8825->sar_hysteresis << NAU8825_KEYDET_HYSTERESIS_SFT); + regmap_update_bits(regmap, NAU8825_REG_KEYDET_CTRL, + NAU8825_KEYDET_SHORTKEY_DEBOUNCE_MASK, + nau8825->key_debounce << NAU8825_KEYDET_SHORTKEY_DEBOUNCE_SFT); + + regmap_write(regmap, NAU8825_REG_VDET_THRESHOLD_1, + (nau8825->sar_threshold[0] << 8) | nau8825->sar_threshold[1]); + regmap_write(regmap, NAU8825_REG_VDET_THRESHOLD_2, + (nau8825->sar_threshold[2] << 8) | nau8825->sar_threshold[3]); + regmap_write(regmap, NAU8825_REG_VDET_THRESHOLD_3, + (nau8825->sar_threshold[4] << 8) | nau8825->sar_threshold[5]); + regmap_write(regmap, NAU8825_REG_VDET_THRESHOLD_4, + (nau8825->sar_threshold[6] << 8) | nau8825->sar_threshold[7]); + + /* Enable short press and release interruptions */ + regmap_update_bits(regmap, NAU8825_REG_INTERRUPT_MASK, + NAU8825_IRQ_KEY_SHORT_PRESS_EN | NAU8825_IRQ_KEY_RELEASE_EN, 0); + + /* Enable DDACR needed for interrupts + * It is the same as force_enable_pin("DDACR") we do later */ + regmap_update_bits(regmap, NAU8825_REG_ENA_CTRL, 0x0400, 0x0400); +} + +static void nau8825_init_regs(struct nau8825 *nau8825) +{ + struct regmap *regmap = nau8825->regmap; + + /* VMID Enable and Tieoff */ + regmap_write(regmap, NAU8825_REG_BIAS_ADJ, 0x0060); + /* Analog Bias Enable, Disable Boost Driver, + Automatic Short circuit protection enable */ + regmap_write(regmap, NAU8825_REG_BOOST, 0x3140); + /* Ground HP Outputs[1:0], + Enable Automatic Mic/Gnd switching reading on insert interrupt[6] */ + regmap_write(regmap, NAU8825_REG_HSD_CTRL, 0x004f); + + regmap_update_bits(regmap, NAU8825_REG_GPIO12_CTRL, + NAU8825_JKDET_PULL_SELECT, + nau8825->jkdet_pullup ? NAU8825_JKDET_PULL_SELECT : 0); + + regmap_update_bits(regmap, NAU8825_REG_JACK_DET_CTRL, + NAU8825_JACK_INSERT_DEBOUNCE_MASK, + nau8825->jack_insert_debounce << NAU8825_JACK_INSERT_DEBOUNCE_SFT); + regmap_update_bits(regmap, NAU8825_REG_JACK_DET_CTRL, + NAU8825_JACK_EJECT_DEBOUNCE_MASK, + nau8825->jack_eject_debounce << NAU8825_JACK_EJECT_DEBOUNCE_SFT); + + /* IRQ Output Enable */ + regmap_update_bits(regmap, NAU8825_REG_INTERRUPT_MASK, + NAU8825_IRQ_OUTPUT_EN, NAU8825_IRQ_OUTPUT_EN); + /* Unmask needed IRQs: 1 - disable, 0 - enable */ + regmap_update_bits(regmap, NAU8825_REG_INTERRUPT_MASK, + NAU8825_IRQ_HEADSET_COMPLETE_EN | NAU8825_IRQ_EJECT_EN, 0); + + regmap_update_bits(regmap, NAU8825_REG_MIC_BIAS, + NAU8825_MICBIAS_VOLTAGE_MASK, nau8825->micbias_voltage); + + if (nau8825->sar_threshold_num) + nau8825_setup_buttons(nau8825); +} + +static const struct regmap_config nau8825_regmap_config = { + .val_bits = 16, + .reg_bits = 16, + + .max_register = NAU8825_REG_MAX, + .readable_reg = nau8825_readable_reg, + .writeable_reg = nau8825_writeable_reg, + .volatile_reg = nau8825_volatile_reg, + + .cache_type = REGCACHE_RBTREE, + .reg_defaults = nau8825_reg_defaults, + .num_reg_defaults = ARRAY_SIZE(nau8825_reg_defaults), +}; + +static int nau8825_codec_probe(struct snd_soc_codec *codec) +{ + struct nau8825 *nau8825 = snd_soc_codec_get_drvdata(codec); + + nau8825->dapm = &codec->dapm; + + /* The interrupt clock is gated by x1[10:8], + * one of them needs to be enabled all the time for + * interrupts to happen. */ + snd_soc_dapm_force_enable_pin(&codec->dapm, "DDACR"); + snd_soc_dapm_sync(&codec->dapm); + + /* Unmask interruptions. Handler uses dapm object so we can enable + * interruptions only after dapm is fully initialized. */ + regmap_write(nau8825->regmap, NAU8825_REG_INTERRUPT_DIS_CTRL, 0); + nau8825_restart_jack_detection(nau8825->regmap); + + return 0; +} + +static int nau8825_configure_sysclk(struct nau8825 *nau8825, int clk_id, + unsigned int freq) +{ + struct regmap *regmap = nau8825->regmap; + + switch (clk_id) { + case NAU8825_CLK_MCLK: + regmap_update_bits(regmap, NAU8825_REG_CLK_DIVIDER, + NAU8825_CLK_SRC_MASK, NAU8825_CLK_SRC_MCLK); + regmap_update_bits(regmap, NAU8825_REG_FLL6, NAU8825_DCO_EN, 0); + break; + case NAU8825_CLK_INTERNAL: + regmap_update_bits(regmap, NAU8825_REG_FLL6, NAU8825_DCO_EN, + NAU8825_DCO_EN); + regmap_update_bits(regmap, NAU8825_REG_CLK_DIVIDER, + NAU8825_CLK_SRC_MASK, NAU8825_CLK_SRC_VCO); + break; + default: + dev_err(nau8825->dev, "Invalid clock id (%d)\n", clk_id); + return -EINVAL; + } + + dev_dbg(nau8825->dev, "Sysclk is %dHz and clock id is %d\n", freq, + clk_id); + return 0; +} + +int nau8825_set_sysclk(struct snd_soc_codec *codec, int clk_id, int source, + unsigned int freq, int dir) +{ + struct nau8825 *nau8825 = snd_soc_codec_get_drvdata(codec); + + return nau8825_configure_sysclk(nau8825, clk_id, freq); +} + +static struct snd_soc_codec_driver nau8825_codec_driver = { + .probe = nau8825_codec_probe, + .set_sysclk = nau8825_set_sysclk, + + .controls = nau8825_controls, + .num_controls = ARRAY_SIZE(nau8825_controls), + .dapm_widgets = nau8825_dapm_widgets, + .num_dapm_widgets = ARRAY_SIZE(nau8825_dapm_widgets), + .dapm_routes = nau8825_dapm_routes, + .num_dapm_routes = ARRAY_SIZE(nau8825_dapm_routes), +}; + +static void nau8825_reset_chip(struct regmap *regmap) +{ + regmap_write(regmap, NAU8825_REG_RESET, 0x00); + regmap_write(regmap, NAU8825_REG_RESET, 0x00); +} + +static int nau8825_i2c_probe(struct i2c_client *i2c, + const struct i2c_device_id *id) +{ + struct device *dev = &i2c->dev; + struct nau8825 *nau8825; + int ret, value; + + nau8825 = devm_kzalloc(dev, sizeof(*nau8825), GFP_KERNEL); + if (!nau8825) + return -ENOMEM; + + i2c_set_clientdata(i2c, nau8825); + + nau8825->regmap = devm_regmap_init_i2c(i2c, &nau8825_regmap_config); + if (IS_ERR(nau8825->regmap)) + return PTR_ERR(nau8825->regmap); + nau8825->irq = i2c->irq; + nau8825->dev = dev; + + nau8825->jkdet_pullup = device_property_read_bool(dev, + "nuvoton,jkdet-pullup"); + device_property_read_u32(dev, "nuvoton,micbias-voltage", + &nau8825->micbias_voltage); + device_property_read_u32(dev, "nuvoton,sar-threshold-num", + &nau8825->sar_threshold_num); + device_property_read_u32_array(dev, "nuvoton,sar-threshold", + nau8825->sar_threshold, nau8825->sar_threshold_num); + device_property_read_u32(dev, "nuvoton,sar-hysteresis", + &nau8825->sar_hysteresis); + device_property_read_u32(dev, "nuvoton,sar-voltage", + &nau8825->sar_voltage); + device_property_read_u32(dev, "nuvoton,short-key-debounce", + &nau8825->key_debounce); + device_property_read_u32(dev, "nuvoton,jack-insert-debounce", + &nau8825->jack_insert_debounce); + device_property_read_u32(dev, "nuvoton,jack-eject-debounce", + &nau8825->jack_eject_debounce); + + + nau8825_reset_chip(nau8825->regmap); + ret = regmap_read(nau8825->regmap, NAU8825_REG_I2C_DEVICE_ID, &value); + if (ret < 0) { + dev_err(dev, "Failed to read device id from the NAU8825: %d\n", + ret); + return ret; + } + if ((value & NAU8825_SOFTWARE_ID_MASK) != + NAU8825_SOFTWARE_ID_NAU8825) { + dev_err(dev, "Not a NAU8825 chip\n"); + return -ENODEV; + } + + nau8825_init_regs(nau8825); + + /* Enable internal VCO needed for interruptions */ + nau8825_configure_sysclk(nau8825, NAU8825_CLK_INTERNAL, 0); + + /* Chip needs one FSCLK cycle in order to generate interrupts, + * as we cannot guarantee one will be provided by the system. Turning + * master mode on then off enables us to generate that FSCLK cycle + * with a minimum of contention on the clock bus. + * Enables master mode and correctly divides BCLK and FSCLK from MCLK. + */ + regmap_update_bits(nau8825->regmap, NAU8825_REG_I2S_PCM_CTRL2, + NAU8825_I2S_MS_MASK, NAU8825_I2S_MS_MASTER); + regmap_update_bits(nau8825->regmap, NAU8825_REG_I2S_PCM_CTRL2, + NAU8825_I2S_MS_MASK, NAU8825_I2S_MS_SLAVE); + + if (nau8825->irq) { + int ret = devm_request_threaded_irq(dev, nau8825->irq, NULL, + nau8825_interrupt, IRQF_TRIGGER_LOW | IRQF_ONESHOT, + "nau8825", nau8825); + + if (ret) { + dev_err(dev, "Cannot request irq %d (%d)\n", + nau8825->irq, ret); + return ret; + } + } + + return snd_soc_register_codec(&i2c->dev, &nau8825_codec_driver, + &nau8825_dai, 1); +} + +static int nau8825_i2c_remove(struct i2c_client *client) +{ + snd_soc_unregister_codec(&client->dev); + return 0; +} + +static const struct i2c_device_id nau8825_i2c_ids[] = { + { "nau8825", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, nau8825_i2c_ids); + +static struct i2c_driver nau8825_driver = { + .driver = { + .name = "nau8825", + .owner = THIS_MODULE, + }, + .probe = nau8825_i2c_probe, + .remove = nau8825_i2c_remove, + .id_table = nau8825_i2c_ids, +}; +module_i2c_driver(nau8825_driver); + +MODULE_DESCRIPTION("ASoC nau8825 driver"); +MODULE_AUTHOR("Anatol Pomozov anatol@chromium.org"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/nau8825.h b/sound/soc/codecs/nau8825.h new file mode 100644 index 0000000..bb103f0 --- /dev/null +++ b/sound/soc/codecs/nau8825.h @@ -0,0 +1,276 @@ +/* + * NAU8825 ALSA SoC audio driver + * + * Copyright 2015 Google Inc. + * Author: Anatol Pomozov anatol.pomozov@chrominium.org + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __NAU8825_H__ +#define __NAU8825_H__ + +#define NAU8825_REG_RESET 0x00 +#define NAU8825_REG_ENA_CTRL 0x01 +#define NAU8825_REG_CLK_DIVIDER 0x03 +#define NAU8825_REG_FLL1 0x04 +#define NAU8825_REG_FLL2 0x05 +#define NAU8825_REG_FLL3 0x06 +#define NAU8825_REG_FLL4 0x07 +#define NAU8825_REG_FLL5 0x08 +#define NAU8825_REG_FLL6 0x09 +#define NAU8825_REG_FLL_VCO_RSV 0x0a +#define NAU8825_REG_HSD_CTRL 0x0c +#define NAU8825_REG_JACK_DET_CTRL 0x0d +#define NAU8825_REG_INTERRUPT_MASK 0x0f +#define NAU8825_REG_IRQ_STATUS 0x10 +#define NAU8825_REG_INT_CLR_KEY_STATUS 0x11 +#define NAU8825_REG_INTERRUPT_DIS_CTRL 0x12 +#define NAU8825_REG_SAR_CTRL 0x13 +#define NAU8825_REG_KEYDET_CTRL 0x14 +#define NAU8825_REG_VDET_THRESHOLD_1 0x15 +#define NAU8825_REG_VDET_THRESHOLD_2 0x16 +#define NAU8825_REG_VDET_THRESHOLD_3 0x17 +#define NAU8825_REG_VDET_THRESHOLD_4 0x18 +#define NAU8825_REG_GPIO34_CTRL 0x19 +#define NAU8825_REG_GPIO12_CTRL 0x1a +#define NAU8825_REG_TDM_CTRL 0x1b +#define NAU8825_REG_I2S_PCM_CTRL1 0x1c +#define NAU8825_REG_I2S_PCM_CTRL2 0x1d +#define NAU8825_REG_LEFT_TIME_SLOT 0x1e +#define NAU8825_REG_RIGHT_TIME_SLOT 0x1f +#define NAU8825_REG_BIQ_CTRL 0x20 +#define NAU8825_REG_BIQ_COF1 0x21 +#define NAU8825_REG_BIQ_COF2 0x22 +#define NAU8825_REG_BIQ_COF3 0x23 +#define NAU8825_REG_BIQ_COF4 0x24 +#define NAU8825_REG_BIQ_COF5 0x25 +#define NAU8825_REG_BIQ_COF6 0x26 +#define NAU8825_REG_BIQ_COF7 0x27 +#define NAU8825_REG_BIQ_COF8 0x28 +#define NAU8825_REG_BIQ_COF9 0x29 +#define NAU8825_REG_BIQ_COF10 0x2a +#define NAU8825_REG_ADC_RATE 0x2b +#define NAU8825_REG_DAC_CTRL1 0x2c +#define NAU8825_REG_DAC_CTRL2 0x2d +#define NAU8825_REG_DAC_DGAIN_CTRL 0x2f +#define NAU8825_REG_ADC_DGAIN_CTRL 0x30 +#define NAU8825_REG_MUTE_CTRL 0x31 +#define NAU8825_REG_HSVOL_CTRL 0x32 +#define NAU8825_REG_DACL_CTRL 0x33 +#define NAU8825_REG_DACR_CTRL 0x34 +#define NAU8825_REG_ADC_DRC_KNEE_IP12 0x38 +#define NAU8825_REG_ADC_DRC_KNEE_IP34 0x39 +#define NAU8825_REG_ADC_DRC_SLOPES 0x3a +#define NAU8825_REG_ADC_DRC_ATKDCY 0x3b +#define NAU8825_REG_DAC_DRC_KNEE_IP12 0x45 +#define NAU8825_REG_DAC_DRC_KNEE_IP34 0x46 +#define NAU8825_REG_DAC_DRC_SLOPES 0x47 +#define NAU8825_REG_DAC_DRC_ATKDCY 0x48 +#define NAU8825_REG_IMM_MODE_CTRL 0x4c +#define NAU8825_REG_IMM_RMS_L 0x4d +#define NAU8825_REG_IMM_RMS_R 0x4e +#define NAU8825_REG_CLASSG_CTRL 0x50 +#define NAU8825_REG_OPT_EFUSE_CTRL 0x51 +#define NAU8825_REG_MISC_CTRL 0x55 +#define NAU8825_REG_I2C_DEVICE_ID 0x58 +#define NAU8825_REG_SARDOUT_RAM_STATUS 0x59 +#define NAU8825_REG_BIAS_ADJ 0x66 +#define NAU8825_REG_TRIM_SETTINGS 0x68 +#define NAU8825_REG_ANALOG_CONTROL_1 0x69 +#define NAU8825_REG_ANALOG_CONTROL_2 0x6a +#define NAU8825_REG_ANALOG_ADC_1 0x71 +#define NAU8825_REG_ANALOG_ADC_2 0x72 +#define NAU8825_REG_RDAC 0x73 +#define NAU8825_REG_MIC_BIAS 0x74 +#define NAU8825_REG_BOOST 0x76 +#define NAU8825_REG_FEPGA 0x77 +#define NAU8825_REG_POWER_UP_CONTROL 0x7f +#define NAU8825_REG_CHARGE_PUMP 0x80 +#define NAU8825_REG_CHARGE_PUMP_INPUT_READ 0x81 +#define NAU8825_REG_GENERAL_STATUS 0x82 +#define NAU8825_REG_MAX NAU8825_REG_GENERAL_STATUS + +/* ENA_CTRL (0x1) */ +#define NAU8825_ENABLE_DACR_SFT 10 +#define NAU8825_ENABLE_DACL_SFT 9 +#define NAU8825_ENABLE_ADC_SFT 8 +#define NAU8825_ENABLE_SAR_SFT 1 + +/* CLK_DIVIDER (0x3) */ +#define NAU8825_CLK_SRC_SFT 15 +#define NAU8825_CLK_SRC_MASK (1 << NAU8825_CLK_SRC_SFT) +#define NAU8825_CLK_SRC_VCO (1 << NAU8825_CLK_SRC_SFT) +#define NAU8825_CLK_SRC_MCLK (0 << NAU8825_CLK_SRC_SFT) + +/* FLL6 (0x9) */ +#define NAU8825_DCO_EN (1 << 15) + +/* HSD_CTRL (0xc) */ +#define NAU8825_HSD_AUTO_MODE (1 << 6) +#define NAU8825_SPKR_DWN1R_SHORT (1 << 1) +#define NAU8825_SPKR_DWN1L_SHORT (1 << 0) + +/* JACK_DET_CTRL (0xd) */ +#define NAU8825_JACK_DET_RESTART (1 << 9) +#define NAU8825_JACK_INSERT_DEBOUNCE_SFT 5 +#define NAU8825_JACK_INSERT_DEBOUNCE_MASK (0x7 << NAU8825_JACK_INSERT_DEBOUNCE_SFT) +#define NAU8825_JACK_EJECT_DEBOUNCE_SFT 2 +#define NAU8825_JACK_EJECT_DEBOUNCE_MASK (0x7 << NAU8825_JACK_EJECT_DEBOUNCE_SFT) + +/* INTERRUPT_MASK (0xf) */ +#define NAU8825_IRQ_OUTPUT_EN (1 << 11) +#define NAU8825_IRQ_HEADSET_COMPLETE_EN (1 << 10) +#define NAU8825_IRQ_KEY_RELEASE_EN (1 << 7) +#define NAU8825_IRQ_KEY_SHORT_PRESS_EN (1 << 5) +#define NAU8825_IRQ_EJECT_EN (1 << 2) + +/* IRQ_STATUS (0x10) */ +#define NAU8825_HEADSET_COMPLETION_IRQ (1 << 10) +#define NAU8825_SHORT_CIRCUIT_IRQ (1 << 9) +#define NAU8825_IMPEDANCE_MEAS_IRQ (1 << 8) +#define NAU8825_KEY_IRQ_MASK (0x7 << 5) +#define NAU8825_KEY_RELEASE_IRQ (1 << 7) +#define NAU8825_KEY_LONG_PRESS_IRQ (1 << 6) +#define NAU8825_KEY_SHORT_PRESS_IRQ (1 << 5) +#define NAU8825_MIC_DETECTION_IRQ (1 << 4) +#define NAU8825_JACK_EJECTION_IRQ_MASK (3 << 2) +#define NAU8825_JACK_EJECTION_DETECTED (1 << 2) +#define NAU8825_JACK_INSERTION_IRQ_MASK (3 << 0) +#define NAU8825_JACK_INSERTION_DETECTED (1 << 0) + +/* SAR_CTRL (0x13) */ +#define NAU8825_SAR_ADC_EN_SFT 12 +#define NAU8825_SAR_ADC_EN (1 << NAU8825_SAR_ADC_EN_SFT) +#define NAU8825_SAR_INPUT_MASK (1 << 11) +#define NAU8825_SAR_INPUT_JKSLV (1 << 11) +#define NAU8825_SAR_INPUT_JKR2 (0 << 11) +#define NAU8825_SAR_TRACKING_GAIN_SFT 8 +#define NAU8825_SAR_TRACKING_GAIN_MASK (0x7 << NAU8825_SAR_TRACKING_GAIN_SFT) + +/* KEYDET_CTRL (0x14) */ +#define NAU8825_KEYDET_SHORTKEY_DEBOUNCE_SFT 12 +#define NAU8825_KEYDET_SHORTKEY_DEBOUNCE_MASK (0x3 << NAU8825_KEYDET_SHORTKEY_DEBOUNCE_SFT) +#define NAU8825_KEYDET_LEVELS_NR_SFT 8 +#define NAU8825_KEYDET_LEVELS_NR_MASK (0x7 << 8) +#define NAU8825_KEYDET_HYSTERESIS_SFT 0 +#define NAU8825_KEYDET_HYSTERESIS_MASK 0xf + +/* GPIO12_CTRL (0x1a) */ +/* 0 - pull down, 1 - pull up */ +#define NAU8825_JKDET_PULL_SELECT (1 << 11) + +/* I2S_PCM_CTRL1 (0x1c) */ +#define NAU8825_I2S_BP_SFT 7 +#define NAU8825_I2S_BP_MASK (1 << NAU8825_I2S_BP_SFT) +#define NAU8825_I2S_BP_INV (1 << NAU8825_I2S_BP_SFT) +#define NAU8825_I2S_PCMB_SFT 6 +#define NAU8825_I2S_PCMB_MASK (1 << NAU8825_I2S_PCMB_SFT) +#define NAU8825_I2S_PCMB_EN (1 << NAU8825_I2S_PCMB_SFT) +#define NAU8825_I2S_DL_SFT 2 +#define NAU8825_I2S_DL_MASK (0x3 << NAU8825_I2S_DL_SFT) +#define NAU8825_I2S_DL_16 (0 << NAU8825_I2S_DL_SFT) +#define NAU8825_I2S_DL_20 (1 << NAU8825_I2S_DL_SFT) +#define NAU8825_I2S_DL_24 (2 << NAU8825_I2S_DL_SFT) +#define NAU8825_I2S_DL_32 (3 << NAU8825_I2S_DL_SFT) +#define NAU8825_I2S_DF_SFT 0 +#define NAU8825_I2S_DF_MASK (0x3 << NAU8825_I2S_DF_SFT) +#define NAU8825_I2S_DF_RIGTH (0 << NAU8825_I2S_DF_SFT) +#define NAU8825_I2S_DF_LEFT (1 << NAU8825_I2S_DF_SFT) +#define NAU8825_I2S_DF_I2S (2 << NAU8825_I2S_DF_SFT) +#define NAU8825_I2S_DF_PCM_AB (3 << NAU8825_I2S_DF_SFT) + +/* I2S_PCM_CTRL2 (0x1d) */ +#define NAU8825_I2S_TRISTATE (1 << 15) /* 0 - Normal mode, 1 - Output Hi-Z */ +#define NAU8825_I2S_MS_SFT 3 +#define NAU8825_I2S_MS_MASK (1 << NAU8825_I2S_MS_SFT) +#define NAU8825_I2S_MS_MASTER (1 << NAU8825_I2S_MS_SFT) +#define NAU8825_I2S_MS_SLAVE (0 << NAU8825_I2S_MS_SFT) + +/* ADC_RATE (0x2b) */ +#define NAU8825_ADC_SYNC_DOWN_SFT 0 + +/* DAC_CTRL1 (0x2c) */ +#define NAU8825_DAC_CLIP_OFF (1 << 7) +#define NAU8825_DAC_OVERSAMPLE_SFT 0 + +/* MUTE_CTRL (0x31) */ +#define NAU8825_DAC_ZERO_CROSSING_EN (1 << 9) +#define NAU8825_DAC_SOFT_MUTE (1 << 9) + +/* HSVOL_CTRL (0x32) */ +#define NAU8825_HP_MUTE (1 << 15) + +/* DACL_CTRL (0x33) */ +#define NAU8825_DACL_CH_SEL_SFT 9 + +/* DACR_CTRL (0x34) */ +#define NAU8825_DACR_CH_SEL_SFT 9 + +/* I2C_DEVICE_ID (0x58) */ +#define NAU8825_GPIO2JD1 (1 << 7) +#define NAU8825_SOFTWARE_ID_MASK 0x3 +#define NAU8825_SOFTWARE_ID_NAU8825 0x0 + +/* BIAS_ADJ (0x66) */ +#define NAU8825_BIAS_VMID (1 << 6) +#define NAU8825_BIAS_VMID_SEL_MASK (3 << 4) +#define NAU8825_BIAS_VMID_SEL_OPEN (0 << 4) +#define NAU8825_BIAS_VMID_SEL_25KOHM (1 << 4) +#define NAU8825_BIAS_VMID_SEL_125KOHM (2 << 4) +#define NAU8825_BIAS_VMID_SEL_2_5KOHM (3 << 4) + +/* ANALOG_CONTROL_2 (0x6a) */ +#define NAU8825_HP_NON_CLASSG_CURRENT_2xADJ (1 << 12) +#define NAU8825_DAC_CAPACITOR_MSB (1 << 1) +#define NAU8825_DAC_CAPACITOR_LSB (1 << 0) + +/* ANALOG_ADC_2 (0x72) */ +#define NAU8825_ADC_VREFSEL_MASK (0x3 << 8) +#define NAU8825_ADC_VREFSEL_ANALOG (0 << 8) +#define NAU8825_ADC_VREFSEL_VMID (1 << 8) +#define NAU8825_ADC_VREFSEL_VMID_PLUS_0_5DB (2 << 8) +#define NAU8825_ADC_VREFSEL_VMID_PLUS_1DB (3 << 8) +#define NAU8825_POWERUP_ADCL (1 << 6) + +/* MIC_BIAS (0x74) */ +#define NAU8825_MICBIAS_JKSLV (1 << 14) +#define NAU8825_MICBIAS_JKR2 (1 << 12) +#define NAU8825_MICBIAS_POWERUP_SFT 8 +#define NAU8825_MICBIAS_VOLTAGE_SFT 0 +#define NAU8825_MICBIAS_VOLTAGE_MASK 0x7 + +/* BOOST (0x76) */ +#define NAU8825_PRECHARGE_DIS (1 << 13) +#define NAU8825_GLOBAL_BIAS_EN (1 << 12) +#define NAU8825_HP_BOOST_DIS (1 << 12) +#define NAU8825_SHORT_SHUTDOWN_EN (1 << 6) + +/* POWER_UP_CONTROL (0x7f) */ +#define NAU8825_POWERUP_HP_DRV_L (1 << 0) +#define NAU8825_POWERUP_HP_DRV_R (1 << 1) +#define NAU8825_POWERUP_DRV_IN_L (1 << 2) +#define NAU8825_POWERUP_DRV_IN_R (1 << 3) +#define NAU8825_POWERUP_INTEGR_L (1 << 4) +#define NAU8825_POWERUP_INTEGR_R (1 << 5) + +/* CHARGE_PUMP_AND_POWER_DOWN_CONTROL (0x80) */ +#define NAU8825_JAMNODCLOW (1 << 10) +#define NAU8825_POWER_DOWN_DACR (1 << 9) +#define NAU8825_POWER_DOWN_DACL (1 << 8) +#define NAU8825_CHANRGE_PUMP_EN (1 << 5) + + +/* System Clock Source */ +enum { + NAU8825_CLK_MCLK = 0, + NAU8825_CLK_INTERNAL, +}; + +int nau8825_enable_jack_detect(struct snd_soc_codec *codec, + struct snd_soc_jack *jack); + + +#endif /* __NAU8825_H__ */