[alsa-devel] [PATCH v5] ASoC: add RT286 CODEC driver
From: Bard Liao bardliao@realtek.com
This patch adds the ALC286 codec driver.
ALC286 is a dual mode codec, which can run as HD-A or I2S mode. It is controlled by HD-A verb commands via I2C protocol. The following is the I/O difference between ALC286 and general I2S codecs. 1. A HD-A verb command contains three parts, NID, VID, and PID. And an I2S command contains only two parts: address and data. 2. Not only the register address is written, but the read command also includes the entire write command. 3. rt286 uses different registers for read and write the same bits. As a result, standard regmap is difficult to be used on ALC286. We don't request a standard I/O by snd_soc_codec_set_cache_io anymore. Now we have ,reg_write and .reg_read functions for ALC286's I/O. And we don't use cache due to item 3 above. Some dummy registers (address <= 0xff) are defined for dapm routing. Thhe dummy registers are cache only. Due to item 2 above, HD-A verb commands are put into the address part of regmap. When we issue HD-A verb write commands, the data part of regmap is zero.
Signed-off-by: Bard Liao bardliao@realtek.com Signed-off-by: Gustaw Lewandowski gustaw.lewandowski@intel.com
--- The jack detection function is done by Lewandowski Gustaw. So I add Gustaw's Signed-off-by line in this patch
The difference between this version and previous version is listed below. * Include <sound/hda_verbs.h> instead of hda_codec.h * Fix rt286_update_bits doesn't write the new value to codec issue. * Apply different settings for system clock = 19.2MHz and 24MHz. * Use .set_bclk_ratio instead of .set_dfs. * Change ACPI number from INT33CA to INT343A. * Other minor changes.
--- include/sound/rt286.h | 19 + sound/soc/codecs/Kconfig | 4 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/rt286.c | 1379 +++++++++++++++++++++++++++++++++++++++++++++ sound/soc/codecs/rt286.h | 159 ++++++ 5 files changed, 1563 insertions(+) create mode 100644 include/sound/rt286.h create mode 100644 sound/soc/codecs/rt286.c create mode 100644 sound/soc/codecs/rt286.h
diff --git a/include/sound/rt286.h b/include/sound/rt286.h new file mode 100644 index 0000000..eb773d1 --- /dev/null +++ b/include/sound/rt286.h @@ -0,0 +1,19 @@ +/* + * linux/sound/rt286.h -- Platform data for RT286 + * + * Copyright 2013 Realtek Microelectronics + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __LINUX_SND_RT286_H +#define __LINUX_SND_RT286_H + +struct rt286_platform_data { + bool cbj_en; /*combo jack enable*/ + bool gpio2_en; /*GPIO2 enable*/ +}; + +#endif diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 32d7a6f..c46e722 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -68,6 +68,7 @@ config SND_SOC_ALL_CODECS select SND_SOC_PCM3008 select SND_SOC_PCM512x_I2C if I2C select SND_SOC_PCM512x_SPI if SPI_MASTER + select SND_SOC_RT286 if I2C select SND_SOC_RT5631 if I2C select SND_SOC_RT5640 if I2C select SND_SOC_SGTL5000 if I2C @@ -379,6 +380,9 @@ config SND_SOC_PCM512x_SPI select SND_SOC_PCM512x select REGMAP_SPI
+config SND_SOC_RT286 + tristate + config SND_SOC_RT5631 tristate
diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index cb46c4c..ee2f368 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -56,6 +56,7 @@ snd-soc-pcm3008-objs := pcm3008.o snd-soc-pcm512x-objs := pcm512x.o snd-soc-pcm512x-i2c-objs := pcm512x-i2c.o snd-soc-pcm512x-spi-objs := pcm512x-spi.o +snd-soc-rt286-objs := rt286.o snd-soc-rt5631-objs := rt5631.o snd-soc-rt5640-objs := rt5640.o snd-soc-sgtl5000-objs := sgtl5000.o @@ -204,6 +205,7 @@ obj-$(CONFIG_SND_SOC_PCM3008) += snd-soc-pcm3008.o obj-$(CONFIG_SND_SOC_PCM512x) += snd-soc-pcm512x.o obj-$(CONFIG_SND_SOC_PCM512x_I2C) += snd-soc-pcm512x-i2c.o obj-$(CONFIG_SND_SOC_PCM512x_SPI) += snd-soc-pcm512x-spi.o +obj-$(CONFIG_SND_SOC_RT286) += snd-soc-rt286.o obj-$(CONFIG_SND_SOC_RT5631) += snd-soc-rt5631.o obj-$(CONFIG_SND_SOC_RT5640) += snd-soc-rt5640.o obj-$(CONFIG_SND_SOC_SGTL5000) += snd-soc-sgtl5000.o diff --git a/sound/soc/codecs/rt286.c b/sound/soc/codecs/rt286.c new file mode 100644 index 0000000..4621b62 --- /dev/null +++ b/sound/soc/codecs/rt286.c @@ -0,0 +1,1379 @@ +/* + * rt286.c -- RT286 ALSA SoC audio codec driver + * + * Copyright 2013 Realtek Semiconductor Corp. + * Author: Bard Liao bardliao@realtek.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/pm.h> +#include <linux/i2c.h> +#include <linux/platform_device.h> +#include <linux/spi/spi.h> +#include <linux/acpi.h> +#include <sound/core.h> +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/soc-dapm.h> +#include <sound/initval.h> +#include <sound/tlv.h> +#include <sound/jack.h> +#include <sound/rt286.h> +#include <sound/hda_verbs.h> + +#include "rt286.h" + +struct rt286_priv { + struct regmap *regmap; + struct snd_soc_codec *codec; + struct rt286_platform_data pdata; + struct snd_soc_jack *jack; + struct i2c_client *i2c; + int sys_clk; +}; + +static unsigned int rt286_reg_cache[] = { + [RT286_AUDIO_FUNCTION_GROUP] = 0x0000, + [RT286_DAC_OUT1] = 0x7f7f, + [RT286_DAC_OUT2] = 0x7f7f, + [RT286_SPDIF] = 0x0000, + [RT286_ADC_IN1] = 0x4343, + [RT286_ADC_IN2] = 0x4343, + [RT286_MIC1] = 0x0000, + [RT286_MIXER_IN] = 0x000b, + [RT286_MIXER_OUT1] = 0x0002, + [RT286_MIXER_OUT2] = 0x0000, + [RT286_DMIC1] = 0x0000, + [RT286_DMIC2] = 0x0000, + [RT286_LINE1] = 0x0000, + [RT286_BEEP] = 0x0000, + [RT286_VENDOR_REGISTERS] = 0x0000, + [RT286_SPK_OUT] = 0x8080, + [RT286_HP_OUT] = 0x8080, + [RT286_MIXER_IN1] = 0x0000, + [RT286_MIXER_IN2] = 0x0000, +}; + +static int rt286_hw_read(void *context, unsigned int reg, unsigned int *value) +{ + struct i2c_client *client = context; + struct i2c_msg xfer[2]; + int ret; + unsigned int buf = 0x0; + + if (reg <= 0xff) { /*read cache*/ + *value = rt286_reg_cache[reg]; + return 0; + } + reg = cpu_to_be32(reg); + /* Write register */ + xfer[0].addr = client->addr; + xfer[0].flags = 0; + xfer[0].len = 4; + xfer[0].buf = (u8 *)® + + /* Read data */ + xfer[1].addr = client->addr; + xfer[1].flags = I2C_M_RD; + xfer[1].len = 4; + xfer[1].buf = (u8 *)&buf; + + ret = i2c_transfer(client->adapter, xfer, 2); + if (ret < 0) + return ret; + else if (ret != 2) + return -EIO; + + *value = be32_to_cpu(buf); + + return 0; +} + +static int rt286_hw_write(void *context, unsigned int reg, unsigned int value) +{ + struct i2c_client *client = context; + u8 data[4]; + int ret; + + if (reg <= 0xff) { /*write cache*/ + rt286_reg_cache[reg] = value; + return 0; + } + data[0] = (reg >> 24) & 0xff; + data[1] = (reg >> 16) & 0xff; + data[2] = (reg >> 8) & 0xff; + data[3] = reg & 0xff; + + ret = i2c_master_send(client, data, 4); + if (ret == 4) + return 0; + if (ret < 0) + return ret; + else + return -EIO; +} + +static int rt286_update_bits(struct snd_soc_codec *codec, unsigned int vid, + unsigned int nid, unsigned int data, + unsigned int mask, unsigned int value) +{ + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + unsigned int old, new, verb; + int change, ret; + + verb = VERB_CMD((vid | 0x800), nid, data); + regmap_read(rt286->regmap, verb, &old); + new = (old & ~mask) | (value & mask); + change = old != new; + + if (change) { + verb = VERB_CMD(vid, nid, new); + ret = regmap_write(rt286->regmap, verb, 0); + if (ret < 0) { + dev_err(codec->dev, + "Failed to write private reg: %d\n", ret); + goto err; + } + } + return change; + +err: + return ret; +} + +static int rt286_index_write(struct snd_soc_codec *codec, + unsigned int wid, unsigned int index, unsigned int data) +{ + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + int ret; + unsigned int verb; + + verb = VERB_CMD(AC_VERB_SET_COEF_INDEX, wid, index); + ret = regmap_write(rt286->regmap, verb, 0); + if (ret < 0) { + dev_err(codec->dev, "Failed to set private addr: %d\n", ret); + goto err; + } + verb = VERB_CMD(AC_VERB_SET_PROC_COEF, wid, data); + ret = regmap_write(rt286->regmap, verb, 0); + if (ret < 0) { + dev_err(codec->dev, "Failed to set private value: %d\n", ret); + goto err; + } + + return 0; +err: + return ret; +} + +static unsigned int rt286_index_read(struct snd_soc_codec *codec, + unsigned int wid, unsigned int index) +{ + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + int ret; + unsigned int verb, val; + + verb = VERB_CMD(AC_VERB_SET_COEF_INDEX, wid, index); + ret = regmap_write(rt286->regmap, verb, 0); + + if (ret < 0) { + dev_err(codec->dev, "Failed to set private addr: %d\n", ret); + return ret; + } + + verb = VERB_CMD(AC_VERB_GET_PROC_COEF, wid, index); + regmap_read(rt286->regmap, verb, &val); + return val; +} + +static int rt286_index_update_bits(struct snd_soc_codec *codec, + unsigned int wid, unsigned int index, + unsigned int mask, unsigned int data) +{ + unsigned int old, new; + int change, ret; + + old = rt286_index_read(codec, wid, index); + new = (old & ~mask) | (data & mask); + change = old != new; + + if (change) { + ret = rt286_index_write(codec, wid, index, new); + if (ret < 0) { + dev_err(codec->dev, + "Failed to write private reg: %d\n", ret); + goto err; + } + } + return change; + +err: + return ret; +} + +static int rt286_support_power_controls[] = { + RT286_DAC_OUT1, + RT286_DAC_OUT2, + RT286_ADC_IN1, + RT286_ADC_IN2, + RT286_MIC1, + RT286_DMIC1, + RT286_DMIC2, + RT286_SPK_OUT, + RT286_HP_OUT, +}; +#define RT286_POWER_REG_LEN ARRAY_SIZE(rt286_support_power_controls) + +static const struct reg_default rt286_reg[] = { + { RT286_DAC_OUT1, 0x7f7f }, + { RT286_DAC_OUT2, 0x7f7f }, + { RT286_SPDIF, 0x0000 }, + { RT286_ADC_IN1, 0x4343 }, + { RT286_ADC_IN2, 0x4343 }, + { RT286_MIC1, 0x0000 }, + { RT286_MIXER_IN, 0x000b }, + { RT286_MIXER_OUT1, 0x0002 }, + { RT286_MIXER_OUT2, 0x0000 }, + { RT286_SPK_OUT, 0x0000 }, + { RT286_HP_OUT, 0x0000 }, + { RT286_MIXER_IN1, 0x0005 }, + { RT286_MIXER_IN2, 0x0005 }, +}; + +static bool rt286_readable_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case RT286_DAC_OUT1: + case RT286_DAC_OUT2: + case RT286_ADC_IN1: + case RT286_ADC_IN2: + case RT286_MIC1: + case RT286_SPDIF: + case RT286_MIXER_IN: + case RT286_MIXER_OUT1: + case RT286_MIXER_OUT2: + case RT286_DMIC1: + case RT286_DMIC2: + case RT286_SPK_OUT: + case RT286_HP_OUT: + case RT286_MIXER_IN1: + case RT286_MIXER_IN2: + return true; + default: + return false; + } +} + +static int rt286_jack_detect(struct snd_soc_codec *codec, bool *hp, bool *mic) +{ + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + unsigned int val, buf; + int i; + + *hp = false; + *mic = false; + + if (rt286->pdata.cbj_en) { + regmap_read(rt286->regmap, RT286_GET_HP_SENSE, &buf); + + *hp = buf & 0x80000000; + if (*hp) { + /* power on HV,VERF */ + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_POWER_CTRL1, 0x1001, 0x0); + /* power LDO1 */ + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_POWER_CTRL2, 0x4, 0x4); + regmap_write(rt286->regmap, RT286_SET_MIC1_24, 0); + val = rt286_index_read(codec, + RT286_VENDOR_REGISTERS, RT286_CBJ_CTRL2); + + msleep(200); + i = 40; + while (((val & 0x0800) == 0) && (i > 0)) { + val = rt286_index_read(codec, + RT286_VENDOR_REGISTERS, + RT286_CBJ_CTRL2); + i--; + msleep(20); + } + + if (0x0400 == (val & 0x0700)) { + *mic = false; + + regmap_write(rt286->regmap, + RT286_SET_MIC1_20, 0); + /* power off HV,VERF */ + rt286_index_update_bits(codec, + RT286_VENDOR_REGISTERS, + RT286_POWER_CTRL1, 0x1001, 0x1001); + rt286_index_update_bits(codec, + RT286_VENDOR_REGISTERS, + RT286_A_BIAS_CTRL3, 0xc000, 0x0000); + rt286_index_update_bits(codec, + RT286_VENDOR_REGISTERS, + RT286_CBJ_CTRL1, 0x0030, 0x0000); + rt286_index_update_bits(codec, + RT286_VENDOR_REGISTERS, + RT286_A_BIAS_CTRL2, 0xc000, 0x0000); + } else if ((0x0200 == (val & 0x0700)) || + (0x0100 == (val & 0x0700))) { + *mic = true; + } else { + *mic = false; + } + + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_MISC_CTRL1, + 0x0060, 0x0000); + } else { + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_MISC_CTRL1, + 0x0060, 0x0020); + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_A_BIAS_CTRL3, + 0xc000, 0x8000); + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_CBJ_CTRL1, + 0x0030, 0x0020); + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_A_BIAS_CTRL2, + 0xc000, 0x8000); + + *mic = false; + } + } else { + regmap_read(rt286->regmap, RT286_GET_HP_SENSE, &buf); + *hp = buf & 0x80000000; + regmap_read(rt286->regmap, RT286_GET_MIC1_SENSE, &buf); + *mic = buf & 0x80000000; + } + + + /* Clear IRQ */ + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_IRQ_CTRL, 0x1, 0x1); + return 0; +} + +int rt286_mic_detect(struct snd_soc_codec *codec, struct snd_soc_jack *jack) +{ + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + rt286->jack = jack; + + /* Send an initial empty report */ + snd_soc_jack_report(rt286->jack, 0, + SND_JACK_MICROPHONE | SND_JACK_HEADPHONE); + + return 0; +} +EXPORT_SYMBOL_GPL(rt286_mic_detect); + +static const DECLARE_TLV_DB_SCALE(out_vol_tlv, -6350, 50, 0); +static const DECLARE_TLV_DB_SCALE(mic_vol_tlv, 0, 1000, 0); + +static int rt286_vol_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol); + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + unsigned int verb, buf, io = 0x8000; + + if (RT286_ADC_IN1 == mc->reg) + io = 0; + verb = VERB_CMD(AC_VERB_GET_AMP_GAIN_MUTE, mc->reg, (0x2000 | io)); + regmap_read(rt286->regmap, verb, &buf); + ucontrol->value.integer.value[0] = buf & 0x7f; + verb = VERB_CMD(AC_VERB_GET_AMP_GAIN_MUTE, mc->reg, io); + regmap_read(rt286->regmap, verb, &buf); + ucontrol->value.integer.value[1] = buf & 0x7f; + + return 0; +} + +static int rt286_vol_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol); + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + unsigned int verb, vall, valr, io; + + if (RT286_ADC_IN1 == mc->reg) + io = 0x4000; + else + io = 0x8000; + vall = ucontrol->value.integer.value[0]; + valr = ucontrol->value.integer.value[1]; + if (vall == valr) { + vall = vall | 0x3000 | io; + verb = VERB_CMD(AC_VERB_SET_AMP_GAIN_MUTE, mc->reg, vall); + regmap_write(rt286->regmap, verb, 0); + } else { + vall = vall | 0x2000 | io; + verb = VERB_CMD(AC_VERB_SET_AMP_GAIN_MUTE, mc->reg, vall); + regmap_write(rt286->regmap, verb, 0); + valr = valr | 0x1000 | io; + verb = VERB_CMD(AC_VERB_SET_AMP_GAIN_MUTE, mc->reg, valr); + regmap_write(rt286->regmap, verb, 0); + } + + return 0; +} + +static int rt286_mic_gain_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol); + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + unsigned int verb, buf; + + verb = VERB_CMD(AC_VERB_GET_AMP_GAIN_MUTE, mc->reg, 0x0); + regmap_read(rt286->regmap, verb, &buf); + ucontrol->value.integer.value[0] = buf & 0x3; + + return 0; +} + +static int rt286_mic_gain_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol); + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + unsigned int verb, val; + + val = ucontrol->value.integer.value[0]; + val = val | 0x7000; + verb = VERB_CMD(AC_VERB_SET_AMP_GAIN_MUTE, mc->reg, val); + regmap_write(rt286->regmap, verb, 0); + + return 0; +} + +static int rt286_playback_switch_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol); + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + unsigned int verb, buf; + + verb = VERB_CMD(AC_VERB_GET_AMP_GAIN_MUTE, mc->reg, 0xa000); + regmap_read(rt286->regmap, verb, &buf); + ucontrol->value.integer.value[0] = !(buf & 0x80); + verb = VERB_CMD(AC_VERB_GET_AMP_GAIN_MUTE, mc->reg, 0x8000); + regmap_read(rt286->regmap, verb, &buf); + ucontrol->value.integer.value[1] = !(buf & 0x80); + + return 0; +} + +static int rt286_playback_switch_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol); + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + unsigned int verb, vall, valr, val = 0; + + vall = (!ucontrol->value.integer.value[0] << 7); + valr = (!ucontrol->value.integer.value[1] << 7); + if (vall) + val |= 0x8000; + if (valr) + val |= 0x0080; + + if (vall == valr) { + vall = vall | 0xb000; + verb = VERB_CMD(AC_VERB_SET_AMP_GAIN_MUTE, mc->reg, vall); + regmap_write(rt286->regmap, verb, 0); + } else { + vall = vall | 0xa000; + verb = VERB_CMD(AC_VERB_SET_AMP_GAIN_MUTE, mc->reg, vall); + regmap_write(rt286->regmap, verb, 0); + valr = valr | 0x9000; + verb = VERB_CMD(AC_VERB_SET_AMP_GAIN_MUTE, mc->reg, valr); + regmap_write(rt286->regmap, verb, 0); + } + snd_soc_update_bits(codec, mc->reg, 0x8080, val); + + return 0; +} + +static const struct snd_kcontrol_new rt286_snd_controls[] = { + SOC_DOUBLE_EXT_TLV("DAC0 Playback Volume", RT286_DAC_OUT1, + 8, 0, 0x7f, 0, + rt286_vol_get, rt286_vol_put, + out_vol_tlv), + SOC_DOUBLE_EXT_TLV("ADC0 Capture Volume", RT286_ADC_IN1, + 8, 0, 0x7f, 0, + rt286_vol_get, rt286_vol_put, + out_vol_tlv), + SOC_SINGLE_EXT_TLV("AMIC Volume", RT286_MIC1, 0, 0x3, 0, + rt286_mic_gain_get, rt286_mic_gain_put, + mic_vol_tlv), + SOC_DOUBLE_EXT("Headphone Playback Switch", RT286_HP_OUT, + 15, 8, 1, 1, rt286_playback_switch_get, + rt286_playback_switch_put), + SOC_DOUBLE_EXT("Speaker Playback Switch", RT286_SPK_OUT, + 15, 8, 1, 1, rt286_playback_switch_get, + rt286_playback_switch_put), +}; + +/* Digital Mixer */ +static const struct snd_kcontrol_new rt286_front_mix[] = { + SOC_DAPM_SINGLE("DAC Switch", RT286_MIXER_OUT1, + RT286_M_FRONT_DAC_SFT, 1, 1), + SOC_DAPM_SINGLE("RECMIX Switch", RT286_MIXER_OUT1, + RT286_M_FRONT_REC_SFT, 1, 1), +}; + +/* Analog Input Mixer */ +static const struct snd_kcontrol_new rt286_rec_mix[] = { + SOC_DAPM_SINGLE("Beep Switch", RT286_MIXER_IN, + RT286_M_REC_BEEP_SFT, 1, 1), + SOC_DAPM_SINGLE("Line1 Switch", RT286_MIXER_IN, + RT286_M_REC_LINE1_SFT, 1, 1), + SOC_DAPM_SINGLE("Mic1 Switch", RT286_MIXER_IN, + RT286_M_REC_MIC1_SFT, 1, 1), + SOC_DAPM_SINGLE("I2S Switch", RT286_MIXER_IN, + RT286_M_REC_I2S_SFT, 1, 1), +}; + +static const struct snd_kcontrol_new spo_enable_control = + SOC_DAPM_SINGLE("Switch", RT286_SPK_OUT, + RT286_M_SPK_MUX_SFT, 1, 1); + +static const struct snd_kcontrol_new hpo_enable_control = + SOC_DAPM_SINGLE("Switch", RT286_HP_OUT, + RT286_M_HP_MUX_SFT, 1, 1); + +/* ADC0 source */ +static const char * const rt286_adc_src[] = { + "Mic", "Dmic" +}; + +static int rt286_adc_values[] = { + 0, 5, +}; + +static SOC_VALUE_ENUM_SINGLE_DECL( + rt286_adc0_enum, RT286_MIXER_IN1, RT286_ADC_SEL_SFT, + RT286_ADC_SEL_MASK, rt286_adc_src, rt286_adc_values); + +static const struct snd_kcontrol_new rt286_adc0_mux = + SOC_DAPM_VALUE_ENUM("ADC 0 source", rt286_adc0_enum); + +static SOC_VALUE_ENUM_SINGLE_DECL( + rt286_adc1_enum, RT286_MIXER_IN2, RT286_ADC_SEL_SFT, + RT286_ADC_SEL_MASK, rt286_adc_src, rt286_adc_values); + +static const struct snd_kcontrol_new rt286_adc1_mux = + SOC_DAPM_VALUE_ENUM("ADC 1 source", rt286_adc1_enum); + +/* HP-OUT source */ +static const char * const rt286_hpo_src[] = { + "Front", "Surround" +}; + +static SOC_ENUM_SINGLE_DECL(rt286_hpo_enum, RT286_HP_OUT, + RT286_HP_SEL_SFT, rt286_hpo_src); + +static const struct snd_kcontrol_new rt286_hpo_mux = +SOC_DAPM_ENUM("HPO source", rt286_hpo_enum); + +/* SPK-OUT source */ +static const char * const rt286_spo_src[] = { + "Front", "Surround" +}; + +static SOC_ENUM_SINGLE_DECL(rt286_spo_enum, RT286_SPK_OUT, + RT286_SPK_SEL_SFT, rt286_spo_src); + +static const struct snd_kcontrol_new rt286_spo_mux = +SOC_DAPM_ENUM("SPO source", rt286_spo_enum); + +/* SPDIF source */ +static const char * const rt286_spdif_src[] = { + "PCM-IN 0", "PCM-IN 1", "SP-OUT", "PP" +}; + +static SOC_ENUM_SINGLE_DECL(rt286_spdif_enum, RT286_SPDIF, + RT286_SPDIF_SEL_SFT, rt286_spdif_src); + +static const struct snd_kcontrol_new rt286_spdif_mux = +SOC_DAPM_ENUM("SPDIF source", rt286_spdif_enum); + + +static int rt286_spk_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_codec *codec = w->codec; + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt286->regmap, RT286_SET_SPK_D0, 0); + regmap_write(rt286->regmap, RT286_ENABLE_SPK, 0); + regmap_write(rt286->regmap, RT286_SPK_EAPD_HIGH, 0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt286->regmap, RT286_SPK_EAPD_LOW, 0); + regmap_write(rt286->regmap, RT286_DISABLE_SPK, 0); + regmap_write(rt286->regmap, RT286_SET_SPK_D3, 0); + break; + + default: + return 0; + } + + return 0; +} + +static int rt286_hp_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_codec *codec = w->codec; + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + unsigned int val, buf; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_read(rt286->regmap, RT286_HP_OUT, &buf); + val = buf & 0x8080; + switch (val) { + case 0x0: + regmap_write(rt286->regmap, RT286_UNMUTE_HPO, 0); + break; + case 0x8000: + regmap_write(rt286->regmap, RT286_UNMUTE_HPO_R, 0); + break; + case 0x0080: + regmap_write(rt286->regmap, RT286_UNMUTE_HPO_L, 0); + break; + } + if (val != 0x8080) + mdelay(100); + break; + + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt286->regmap, RT286_MUTE_HPO, 0); + break; + + default: + return 0; + } + + return 0; +} + +static int rt286_set_power_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_codec *codec = w->codec; + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt286->regmap, RT286_SET_D0(w->reg), 0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt286->regmap, RT286_SET_D3(w->reg), 0); + break; + default: + return 0; + } + + return 0; +} + +static int rt286_set_dmic1_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_codec *codec = w->codec; + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt286->regmap, RT286_SET_DMIC1_D0, 0); + regmap_write(rt286->regmap, RT286_ENABLE_DMIC1, 0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt286->regmap, RT286_DISABLE_DMIC1, 0); + regmap_write(rt286->regmap, RT286_SET_DMIC1_D3, 0); + break; + default: + return 0; + } + + return 0; +} + +static int rt286_hp_pow_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_codec *codec = w->codec; + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt286->regmap, RT286_SET_HPO_D0, 0); + regmap_write(rt286->regmap, RT286_ENABLE_HPO, 0); + break; + + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt286->regmap, RT286_DISABLE_HPO, 0); + regmap_write(rt286->regmap, RT286_SET_HPO_D3, 0); + break; + + default: + return 0; + } + + return 0; +} + +static int rt286_adc_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_codec *codec = w->codec; + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + struct soc_enum *e; + unsigned int verb, val, buf; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + if (rt286->pdata.cbj_en) { + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_A_BIAS_CTRL3, 0xc000, 0x8000); + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_CBJ_CTRL1, 0x0030, 0x0020); + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_A_BIAS_CTRL2, 0xc000, 0x8000); + } + regmap_write(rt286->regmap, RT286_SET_D0(w->reg), 0); + rt286_update_bits(codec, AC_VERB_SET_AMP_GAIN_MUTE, + w->reg, 0, 0x7080, 0x7000); + break; + case SND_SOC_DAPM_PRE_PMD: + rt286_update_bits(codec, AC_VERB_SET_AMP_GAIN_MUTE, + w->reg, 0, 0x7080, 0x7080); + regmap_write(rt286->regmap, RT286_SET_D3(w->reg), 0); + break; + case SND_SOC_DAPM_POST_REG: + e = (struct soc_enum *)kcontrol->private_value; + regmap_read(rt286->regmap, e->reg, &buf); + val = buf & RT286_ADC_SEL_MASK; + verb = VERB_CMD(AC_VERB_SET_CONNECT_SEL, e->reg, val); + regmap_write(rt286->regmap, verb, 0); + break; + default: + return 0; + } + + return 0; +} + +static int rt286_out_mux_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_codec *codec = w->codec; + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + struct soc_enum *e = (struct soc_enum *)kcontrol->private_value; + unsigned int verb, val, buf; + + switch (event) { + case SND_SOC_DAPM_POST_REG: + regmap_read(rt286->regmap, e->reg, &buf); + val = buf & 0x1; + verb = VERB_CMD(AC_VERB_SET_CONNECT_SEL, e->reg, val); + regmap_write(rt286->regmap, verb, 0); + break; + default: + return 0; + } + + return 0; +} + +static const struct snd_soc_dapm_widget rt286_dapm_widgets[] = { + /* Input Lines */ + SND_SOC_DAPM_INPUT("DMIC1 Pin"), + SND_SOC_DAPM_INPUT("DMIC2 Pin"), + SND_SOC_DAPM_INPUT("MIC1"), + SND_SOC_DAPM_INPUT("LINE1"), + SND_SOC_DAPM_INPUT("Beep"), + + /* DMIC */ + SND_SOC_DAPM_PGA_E("DMIC1", RT286_DMIC1, 15, 0, + NULL, 0, rt286_set_dmic1_event, + SND_SOC_DAPM_PRE_PMD | SND_SOC_DAPM_POST_PMU), + SND_SOC_DAPM_PGA_E("DMIC2", RT286_DMIC2, 15, 0, + NULL, 0, rt286_set_power_event, + SND_SOC_DAPM_PRE_PMD | SND_SOC_DAPM_POST_PMU), + SND_SOC_DAPM_SUPPLY("DMIC Receiver", SND_SOC_NOPM, + 0, 0, NULL, 0), + + /* REC Mixer */ + SND_SOC_DAPM_MIXER("RECMIX", SND_SOC_NOPM, 0, 0, + rt286_rec_mix, ARRAY_SIZE(rt286_rec_mix)), + + /* ADCs */ + SND_SOC_DAPM_ADC("ADC 0", NULL, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_ADC("ADC 1", NULL, SND_SOC_NOPM, 0, 0), + + /* ADC Mux */ + SND_SOC_DAPM_MUX_E("ADC 0 Mux", RT286_ADC_IN1, 15, 0, + &rt286_adc0_mux, rt286_adc_event, SND_SOC_DAPM_PRE_PMD | + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_POST_REG), + SND_SOC_DAPM_MUX_E("ADC 1 Mux", RT286_ADC_IN2, 15, 0, + &rt286_adc1_mux, rt286_adc_event, SND_SOC_DAPM_PRE_PMD | + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_POST_REG), + + + /* Audio Interface */ + SND_SOC_DAPM_AIF_IN("AIF1RX", "AIF1 Playback", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_OUT("AIF1TX", "AIF1 Capture", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_IN("AIF2RX", "AIF2 Playback", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_OUT("AIF2TX", "AIF2 Capture", 0, SND_SOC_NOPM, 0, 0), + + + /* Output Side */ + + /* DACs */ + SND_SOC_DAPM_DAC_E("DAC 0", NULL, RT286_DAC_OUT1, + 15, 0, rt286_set_power_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_DAC_E("DAC 1", NULL, RT286_DAC_OUT2, + 15, 0, rt286_set_power_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + + /* Output Mux */ + SND_SOC_DAPM_MUX_E("SPK Mux", SND_SOC_NOPM, 0, 0, + &rt286_spo_mux, + rt286_out_mux_event, + SND_SOC_DAPM_POST_REG), + + SND_SOC_DAPM_MUX_E("HPO Mux", SND_SOC_NOPM, 0, 0, + &rt286_hpo_mux, + rt286_out_mux_event, + SND_SOC_DAPM_POST_REG), + + SND_SOC_DAPM_SUPPLY("HP Power", SND_SOC_NOPM, + 0, 0, rt286_hp_pow_event, + SND_SOC_DAPM_PRE_PMD | SND_SOC_DAPM_POST_PMU), + + SND_SOC_DAPM_MUX("SPDIF Mux", SND_SOC_NOPM, 0, 0, + &rt286_spdif_mux), + + /* Output Mixer */ + SND_SOC_DAPM_MIXER("Front", SND_SOC_NOPM, 0, 0, + rt286_front_mix, ARRAY_SIZE(rt286_front_mix)), + SND_SOC_DAPM_PGA("Surround", SND_SOC_NOPM, 0, 0, NULL, 0), + + /* Output Pga */ + SND_SOC_DAPM_SWITCH_E("SPO", SND_SOC_NOPM, 0, 0, + &spo_enable_control, rt286_spk_event, + SND_SOC_DAPM_PRE_PMD | SND_SOC_DAPM_POST_PMU), + SND_SOC_DAPM_SWITCH_E("HPO", SND_SOC_NOPM, 0, 0, + &hpo_enable_control, rt286_hp_event, + SND_SOC_DAPM_PRE_PMD | SND_SOC_DAPM_POST_PMU), + + /* Output Lines */ + SND_SOC_DAPM_OUTPUT("SPOL"), + SND_SOC_DAPM_OUTPUT("SPOR"), + SND_SOC_DAPM_OUTPUT("HPO Pin"), + SND_SOC_DAPM_OUTPUT("SPDIF"), +}; + +static const struct snd_soc_dapm_route rt286_dapm_routes[] = { + {"DMIC1", NULL, "DMIC1 Pin"}, + {"DMIC2", NULL, "DMIC2 Pin"}, + {"DMIC1", NULL, "DMIC Receiver"}, + {"DMIC2", NULL, "DMIC Receiver"}, + + {"RECMIX", "Beep Switch", "Beep"}, + {"RECMIX", "Line1 Switch", "LINE1"}, + {"RECMIX", "Mic1 Switch", "MIC1"}, + + {"ADC 0 Mux", "Dmic", "DMIC1"}, + {"ADC 0 Mux", "Mic", "MIC1"}, + {"ADC 1 Mux", "Dmic", "DMIC2"}, + {"ADC 1 Mux", "Mic", "MIC1"}, + + {"ADC 0", NULL, "ADC 0 Mux"}, + {"ADC 1", NULL, "ADC 1 Mux"}, + + {"AIF1TX", NULL, "ADC 0"}, + {"AIF2TX", NULL, "ADC 1"}, + + {"DAC 0", NULL, "AIF1RX"}, + {"DAC 1", NULL, "AIF2RX"}, + + {"Front", "DAC Switch", "DAC 0"}, + {"Front", "RECMIX Switch", "RECMIX"}, + + {"Surround", NULL, "DAC 1"}, + + {"SPK Mux", "Front", "Front"}, + {"SPK Mux", "Surround", "Surround"}, + + {"HPO Mux", "Front", "Front"}, + {"HPO Mux", "Surround", "Surround"}, + + {"SPO", "Switch", "SPK Mux"}, + {"HPO", "Switch", "HPO Mux"}, + {"HPO", NULL, "HP Power"}, + + {"SPOL", NULL, "SPO"}, + {"SPOR", NULL, "SPO"}, + {"HPO Pin", NULL, "HPO"}, +}; + +static int rt286_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_codec *codec = dai->codec; + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + unsigned int val = 0; + int d_len_code; + + switch (params_rate(params)) { + /* bit 14 0:48K 1:44.1K */ + case 44100: + val |= 0x4000; + break; + case 48000: + break; + default: + dev_err(codec->dev, "Unsupported sample rate %d\n", + params_rate(params)); + return -EINVAL; + } + switch (rt286->sys_clk) { + case 12288000: + case 24576000: + if (params_rate(params) != 48000) { + dev_err(codec->dev, "Sys_clk is not matched (%d %d)\n", + params_rate(params), rt286->sys_clk); + return -EINVAL; + } + break; + case 11289600: + case 22579200: + if (params_rate(params) != 44100) { + dev_err(codec->dev, "Sys_clk is not matched (%d %d)\n", + params_rate(params), rt286->sys_clk); + return -EINVAL; + } + break; + } + + if (params_channels(params) <= 16) { + /* bit 3:0 Number of Channel */ + val |= (params_channels(params) - 1); + } else { + dev_err(codec->dev, "Unsupported channels %d\n", + params_channels(params)); + return -EINVAL; + } + + d_len_code = 0; + switch (params_format(params)) { + /* bit 6:4 Bits per Sample */ + case SNDRV_PCM_FORMAT_S16_LE: + d_len_code = 0; + val |= (0x1 << 4); + break; + case SNDRV_PCM_FORMAT_S32_LE: + d_len_code = 2; + val |= (0x4 << 4); + break; + case SNDRV_PCM_FORMAT_S20_3LE: + d_len_code = 1; + val |= (0x2 << 4); + break; + case SNDRV_PCM_FORMAT_S24_LE: + d_len_code = 2; + val |= (0x3 << 4); + break; + case SNDRV_PCM_FORMAT_S8: + break; + default: + return -EINVAL; + } + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_I2S_CTRL1, 0x0018, d_len_code << 3); + dev_dbg(codec->dev, "format val = 0x%x\n", val); + + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) + rt286_update_bits(codec, AC_VERB_SET_STREAM_FORMAT, + RT286_DAC_OUT1, 0, 0x407f, val); + else + rt286_update_bits(codec, AC_VERB_SET_STREAM_FORMAT, + RT286_ADC_IN1, 0, 0x407f, val); + + return 0; +} + +static int rt286_set_dai_fmt(struct snd_soc_dai *dai, unsigned int fmt) +{ + struct snd_soc_codec *codec = dai->codec; + + switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { + case SND_SOC_DAIFMT_CBM_CFM: + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_I2S_CTRL1, 0x800, 0x800); + break; + case SND_SOC_DAIFMT_CBS_CFS: + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_I2S_CTRL1, 0x800, 0x0); + break; + default: + return -EINVAL; + } + + switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { + case SND_SOC_DAIFMT_I2S: + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_I2S_CTRL1, 0x300, 0x0); + break; + case SND_SOC_DAIFMT_LEFT_J: + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_I2S_CTRL1, 0x300, 0x1 << 8); + break; + case SND_SOC_DAIFMT_DSP_A: + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_I2S_CTRL1, 0x300, 0x2 << 8); + break; + case SND_SOC_DAIFMT_DSP_B: + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_I2S_CTRL1, 0x300, 0x3 << 8); + break; + default: + return -EINVAL; + } + /* bit 15 Stream Type 0:PCM 1:Non-PCM */ + rt286_update_bits(codec, AC_VERB_SET_STREAM_FORMAT, + RT286_DAC_OUT1, 0, 0x8000, 0x0); + rt286_update_bits(codec, AC_VERB_SET_STREAM_FORMAT, + RT286_ADC_IN1, 0, 0x8000, 0x0); + + return 0; +} + +static int rt286_set_dai_sysclk(struct snd_soc_dai *dai, + int clk_id, unsigned int freq, int dir) +{ + struct snd_soc_codec *codec = dai->codec; + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + + dev_dbg(codec->dev, "%s freq=%d\n", __func__, freq); + + if (RT286_SCLK_S_MCLK == clk_id) { + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_I2S_CTRL2, 0x0100, 0x0); + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_PLL_CTRL1, 0x20, 0x20); + } else { + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_I2S_CTRL2, 0x0100, 0x0100); + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_PLL_CTRL, 0x4, 0x4); + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_PLL_CTRL1, 0x20, 0x0); + } + + switch (freq) { + case 19200000: + if (RT286_SCLK_S_MCLK == clk_id) { + dev_err(codec->dev, "Should not use MCLK\n"); + return -EINVAL; + } + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_I2S_CTRL2, 0x40, 0x40); + break; + case 24000000: + if (RT286_SCLK_S_MCLK == clk_id) { + dev_err(codec->dev, "Should not use MCLK\n"); + return -EINVAL; + } + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_I2S_CTRL2, 0x40, 0x0); + break; + case 12288000: + case 11289600: + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_I2S_CTRL2, 0x8, 0x0); + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_CLK_DIV, 0xfc1e, 0x0004); + break; + case 24576000: + case 22579200: + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_I2S_CTRL2, 0x8, 0x8); + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_CLK_DIV, 0xfc1e, 0x5406); + break; + default: + dev_err(codec->dev, "Unsupported system clock\n"); + return -EINVAL; + } + + rt286->sys_clk = freq; + + return 0; +} + +static int rt286_set_bclk_ratio(struct snd_soc_dai *dai, unsigned int ratio) +{ + struct snd_soc_codec *codec = dai->codec; + + dev_dbg(codec->dev, "%s ratio=%d\n", __func__, ratio); + if (50 == ratio) + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_I2S_CTRL1, 0x1000, 0x1000); + else + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_I2S_CTRL1, 0x1000, 0x0); + + + return 0; +} + +static int rt286_set_bias_level(struct snd_soc_codec *codec, + enum snd_soc_bias_level level) +{ + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + + switch (level) { + case SND_SOC_BIAS_PREPARE: + if (SND_SOC_BIAS_STANDBY == codec->dapm.bias_level) + regmap_write(rt286->regmap, RT286_SET_AUDIO_D0, 0); + break; + + case SND_SOC_BIAS_STANDBY: + regmap_write(rt286->regmap, RT286_SET_AUDIO_D3, 0); + break; + + default: + break; + } + codec->dapm.bias_level = level; + + return 0; +} + +static irqreturn_t rt286_irq(int irq, void *data) +{ + struct rt286_priv *rt286 = data; + bool hp = false; + bool mic = false; + int status = 0; + + rt286_jack_detect(rt286->codec, &hp, &mic); + + if (hp == true) + status |= SND_JACK_HEADPHONE; + + if (mic == true) + status |= SND_JACK_MICROPHONE; + + snd_soc_jack_report(rt286->jack, status, + SND_JACK_MICROPHONE | SND_JACK_HEADPHONE); + + pm_wakeup_event(&rt286->i2c->dev, 300); + + return IRQ_HANDLED; +} + +static int rt286_probe(struct snd_soc_codec *codec) +{ + struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec); + int i, ret; + + regmap_write(rt286->regmap, RT286_SET_AUDIO_D3, 0); + for (i = 0; i < RT286_POWER_REG_LEN; i++) { + regmap_write(rt286->regmap, + RT286_SET_D3(rt286_support_power_controls[i]), 0); + } + + if (!rt286->pdata.cbj_en) { + rt286_index_write(codec, RT286_VENDOR_REGISTERS, + RT286_CBJ_CTRL2, 0x0000); + rt286_index_write(codec, RT286_VENDOR_REGISTERS, + RT286_MIC1_DET_CTRL, 0x0816); + rt286_index_write(codec, RT286_VENDOR_REGISTERS, + RT286_MISC_CTRL1, 0x0000); + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_CBJ_CTRL1, 0xf000, 0xb000); + } else { + rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS, + RT286_CBJ_CTRL1, 0xf000, 0x5000); + } + + mdelay(10); + + if (!rt286->pdata.gpio2_en) + regmap_write(rt286->regmap, RT286_SET_DMIC2_DEFAULT_4000, 0); + else + regmap_write(rt286->regmap, RT286_SET_DMIC2_DEFAULT_0, 0); + + mdelay(10); + + /*Power down LDO2*/ + rt286_index_update_bits(codec, + RT286_VENDOR_REGISTERS, RT286_POWER_CTRL2, 0x8, 0x0); + + codec->dapm.bias_level = SND_SOC_BIAS_OFF; + rt286->codec = codec; + + if (rt286->i2c->irq) { + rt286_index_update_bits(codec, + RT286_VENDOR_REGISTERS, RT286_IRQ_CTRL, 0x2, 0x2); + ret = request_threaded_irq(rt286->i2c->irq, NULL, rt286_irq, + IRQF_TRIGGER_HIGH | IRQF_ONESHOT, "rt286", rt286); + if (ret != 0) { + dev_err(codec->dev, + "Failed to reguest IRQ: %d\n", ret); + return ret; + } + } + + return 0; +} + +#define RT286_STEREO_RATES (SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000) +#define RT286_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE | \ + SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S8) + +struct snd_soc_dai_ops rt286_aif_dai_ops = { + .hw_params = rt286_hw_params, + .set_fmt = rt286_set_dai_fmt, + .set_sysclk = rt286_set_dai_sysclk, + .set_bclk_ratio = rt286_set_bclk_ratio, +}; + +struct snd_soc_dai_driver rt286_dai[] = { + { + .name = "rt286-aif1", + .id = RT286_AIF1, + .playback = { + .stream_name = "AIF1 Playback", + .channels_min = 1, + .channels_max = 2, + .rates = RT286_STEREO_RATES, + .formats = RT286_FORMATS, + }, + .capture = { + .stream_name = "AIF1 Capture", + .channels_min = 1, + .channels_max = 2, + .rates = RT286_STEREO_RATES, + .formats = RT286_FORMATS, + }, + .ops = &rt286_aif_dai_ops, + .symmetric_rates = 1, + }, +}; + +static struct snd_soc_codec_driver soc_codec_dev_rt286 = { + .probe = rt286_probe, + .set_bias_level = rt286_set_bias_level, + .idle_bias_off = true, + .controls = rt286_snd_controls, + .num_controls = ARRAY_SIZE(rt286_snd_controls), + .dapm_widgets = rt286_dapm_widgets, + .num_dapm_widgets = ARRAY_SIZE(rt286_dapm_widgets), + .dapm_routes = rt286_dapm_routes, + .num_dapm_routes = ARRAY_SIZE(rt286_dapm_routes), +}; + +static const struct regmap_config rt286_regmap = { + .reg_bits = 32, + .val_bits = 32, + .reg_write = rt286_hw_write, + .reg_read = rt286_hw_read, + .readable_reg = rt286_readable_register, + .cache_type = REGCACHE_NONE, +}; + +static const struct i2c_device_id rt286_i2c_id[] = { + {"rt286", 0}, + {} +}; +MODULE_DEVICE_TABLE(i2c, rt286_i2c_id); + +static struct acpi_device_id rt286_acpi_match[] = { + { "INT343A", 0 }, + {}, +}; +MODULE_DEVICE_TABLE(acpi, rt286_acpi_match); + +static int rt286_i2c_probe(struct i2c_client *i2c, + const struct i2c_device_id *id) +{ + struct rt286_platform_data *pdata = dev_get_platdata(&i2c->dev); + struct rt286_priv *rt286; + struct device *dev = &i2c->dev; + int ret; + + rt286 = devm_kzalloc(&i2c->dev, + sizeof(struct rt286_priv), + GFP_KERNEL); + if (NULL == rt286) + return -ENOMEM; + + rt286->regmap = devm_regmap_init(dev, NULL, i2c, &rt286_regmap); + if (IS_ERR(rt286->regmap)) { + ret = PTR_ERR(rt286->regmap); + dev_err(&i2c->dev, "Failed to allocate register map: %d\n", + ret); + return ret; + } + + rt286->i2c = i2c; + i2c_set_clientdata(i2c, rt286); + + if (pdata) + rt286->pdata = *pdata; + + ret = devm_snd_soc_register_codec(&i2c->dev, &soc_codec_dev_rt286, + rt286_dai, ARRAY_SIZE(rt286_dai)); + + return ret; +} + +struct i2c_driver rt286_i2c_driver = { + .driver = { + .name = "rt286", + .owner = THIS_MODULE, + .acpi_match_table = ACPI_PTR(rt286_acpi_match), + }, + .probe = rt286_i2c_probe, + .id_table = rt286_i2c_id, +}; + +module_i2c_driver(rt286_i2c_driver); + +MODULE_DESCRIPTION("ASoC RT286 driver"); +MODULE_AUTHOR("Bard Liao bardliao@realtek.com"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/rt286.h b/sound/soc/codecs/rt286.h new file mode 100644 index 0000000..5f9dc99 --- /dev/null +++ b/sound/soc/codecs/rt286.h @@ -0,0 +1,159 @@ +/* + * rt286.h -- RT286 ALSA SoC audio driver + * + * Copyright 2011 Realtek Microelectronics + * Author: Johnny Hsu johnnyhsu@realtek.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __RT286_H__ +#define __RT286_H__ + +#define VERB_CMD(V, N, D) ((N << 20) | (V << 8) | D) + +#define RT286_AUDIO_FUNCTION_GROUP 0x01 +#define RT286_DAC_OUT1 0x02 +#define RT286_DAC_OUT2 0x03 +#define RT286_ADC_IN1 0x09 +#define RT286_ADC_IN2 0x08 +#define RT286_MIXER_IN 0x0b +#define RT286_MIXER_OUT1 0x0c +#define RT286_MIXER_OUT2 0x0d +#define RT286_DMIC1 0x12 +#define RT286_DMIC2 0x13 +#define RT286_SPK_OUT 0x14 +#define RT286_MIC1 0x18 +#define RT286_LINE1 0x1a +#define RT286_BEEP 0x1d +#define RT286_SPDIF 0x1e +#define RT286_VENDOR_REGISTERS 0x20 +#define RT286_HP_OUT 0x21 +#define RT286_MIXER_IN1 0x22 +#define RT286_MIXER_IN2 0x23 + +#define RT286_CONNECTION_INDEX_MIC1 0X0 +#define RT286_CONNECTION_INDEX_DMIC 0X5 + +/* Verb commands */ +#define RT286_SET_D0(NID) VERB_CMD(AC_VERB_SET_POWER_STATE, NID, AC_PWRST_D0) +#define RT286_SET_D3(NID) VERB_CMD(AC_VERB_SET_POWER_STATE, NID, AC_PWRST_D3) + +#define RT286_SET_MIC1_24\ + VERB_CMD(AC_VERB_SET_PIN_WIDGET_CONTROL, RT286_MIC1, 0x24) +#define RT286_SET_MIC1_20\ + VERB_CMD(AC_VERB_SET_PIN_WIDGET_CONTROL, RT286_MIC1, 0x20) +#define RT286_SET_AUDIO_D0 RT286_SET_D0(RT286_AUDIO_FUNCTION_GROUP) +#define RT286_SET_AUDIO_D3 RT286_SET_D3(RT286_AUDIO_FUNCTION_GROUP) +#define RT286_SET_HPO_D0 RT286_SET_D0(RT286_HP_OUT) +#define RT286_SET_HPO_D3 RT286_SET_D3(RT286_HP_OUT) +#define RT286_SET_SPK_D0 RT286_SET_D0(RT286_SPK_OUT) +#define RT286_SET_SPK_D3 RT286_SET_D3(RT286_SPK_OUT) +#define RT286_SET_DMIC1_D0 RT286_SET_D0(RT286_DMIC1) +#define RT286_SET_DMIC1_D3 RT286_SET_D3(RT286_DMIC1) +#define RT286_ENABLE_HPO\ + VERB_CMD(AC_VERB_SET_PIN_WIDGET_CONTROL, RT286_HP_OUT, 0x40) +#define RT286_DISABLE_HPO\ + VERB_CMD(AC_VERB_SET_PIN_WIDGET_CONTROL, RT286_HP_OUT, 0) +#define RT286_ENABLE_SPK\ + VERB_CMD(AC_VERB_SET_PIN_WIDGET_CONTROL, RT286_SPK_OUT, 0x40) +#define RT286_DISABLE_SPK\ + VERB_CMD(AC_VERB_SET_PIN_WIDGET_CONTROL, RT286_SPK_OUT, 0) +#define RT286_ENABLE_DMIC1\ + VERB_CMD(AC_VERB_SET_PIN_WIDGET_CONTROL, RT286_DMIC1, 0x20) +#define RT286_DISABLE_DMIC1\ + VERB_CMD(AC_VERB_SET_PIN_WIDGET_CONTROL, RT286_DMIC1, 0) +#define RT286_SPK_EAPD_HIGH\ + VERB_CMD(AC_VERB_SET_EAPD_BTLENABLE, RT286_SPK_OUT, 0x2) +#define RT286_SPK_EAPD_LOW\ + VERB_CMD(AC_VERB_SET_EAPD_BTLENABLE, RT286_SPK_OUT, 0) +#define RT286_UNMUTE_HPO\ + VERB_CMD(AC_VERB_SET_AMP_GAIN_MUTE, RT286_HP_OUT, 0xb000) +#define RT286_UNMUTE_HPO_R\ + VERB_CMD(AC_VERB_SET_AMP_GAIN_MUTE, RT286_HP_OUT, 0x9000) +#define RT286_UNMUTE_HPO_L\ + VERB_CMD(AC_VERB_SET_AMP_GAIN_MUTE, RT286_HP_OUT, 0xa000) +#define RT286_MUTE_HPO\ + VERB_CMD(AC_VERB_SET_AMP_GAIN_MUTE, RT286_HP_OUT, 0xb080) +#define RT286_GET_HP_SENSE\ + VERB_CMD(AC_VERB_GET_PIN_SENSE, RT286_HP_OUT, 0) +#define RT286_GET_MIC1_SENSE\ + VERB_CMD(AC_VERB_GET_PIN_SENSE, RT286_MIC1, 0) +#define RT286_SET_DMIC2_DEFAULT_4000\ + VERB_CMD(AC_VERB_SET_CONFIG_DEFAULT_BYTES_3, RT286_DMIC2, 0x4000) +#define RT286_SET_DMIC2_DEFAULT_0\ + VERB_CMD(AC_VERB_SET_CONFIG_DEFAULT_BYTES_3, RT286_DMIC2, 0) + +/* Index registers */ +#define RT286_A_BIAS_CTRL1 0x01 +#define RT286_A_BIAS_CTRL2 0x02 +#define RT286_POWER_CTRL1 0x03 +#define RT286_A_BIAS_CTRL3 0x04 +#define RT286_POWER_CTRL2 0x08 +#define RT286_I2S_CTRL1 0x09 +#define RT286_I2S_CTRL2 0x0a +#define RT286_CLK_DIV 0x0b +#define RT286_POWER_CTRL3 0x0f +#define RT286_MIC1_DET_CTRL 0x19 +#define RT286_MISC_CTRL1 0x20 +#define RT286_IRQ_CTRL 0x33 +#define RT286_PLL_CTRL1 0x49 +#define RT286_CBJ_CTRL1 0x4f +#define RT286_CBJ_CTRL2 0x50 +#define RT286_PLL_CTRL 0x63 + +/* SPDIF (0x06) */ +#define RT286_SPDIF_SEL_SFT 0 +#define RT286_SPDIF_SEL_PCM0 0 +#define RT286_SPDIF_SEL_PCM1 1 +#define RT286_SPDIF_SEL_SPOUT 2 +#define RT286_SPDIF_SEL_PP 3 + +/* RECMIX (0x0b) */ +#define RT286_M_REC_BEEP_SFT 0 +#define RT286_M_REC_LINE1_SFT 1 +#define RT286_M_REC_MIC1_SFT 2 +#define RT286_M_REC_I2S_SFT 3 + +/* Front (0x0c) */ +#define RT286_M_FRONT_DAC_SFT 0 +#define RT286_M_FRONT_REC_SFT 1 + +/* SPK-OUT (0x14) */ +#define RT286_M_SPK_MUX_SFT 14 +#define RT286_SPK_SEL_MASK 0x1 +#define RT286_SPK_SEL_SFT 0 +#define RT286_SPK_SEL_F 0 +#define RT286_SPK_SEL_S 1 + +/* HP-OUT (0x21) */ +#define RT286_M_HP_MUX_SFT 14 +#define RT286_HP_SEL_MASK 0x1 +#define RT286_HP_SEL_SFT 0 +#define RT286_HP_SEL_F 0 +#define RT286_HP_SEL_S 1 + +/* ADC (0x22) (0x23) */ +#define RT286_ADC_SEL_MASK 0x7 +#define RT286_ADC_SEL_SFT 0 +#define RT286_ADC_SEL_SURR 0 +#define RT286_ADC_SEL_FRONT 1 +#define RT286_ADC_SEL_DMIC 2 +#define RT286_ADC_SEL_BEEP 4 +#define RT286_ADC_SEL_LINE1 5 +#define RT286_ADC_SEL_I2S 6 +#define RT286_ADC_SEL_MIC1 7 + +#define RT286_SCLK_S_MCLK 0 +#define RT286_SCLK_S_PLL 1 + +enum { + RT286_AIF1, + RT286_AIFS, +}; + +int rt286_mic_detect(struct snd_soc_codec *codec, struct snd_soc_jack *jack); + +#endif /* __RT286_H__ */
On 03/11/2014 08:11 AM, bardliao@realtek.com wrote: [...]
+static unsigned int rt286_reg_cache[] = {
- [RT286_AUDIO_FUNCTION_GROUP] = 0x0000,
- [RT286_DAC_OUT1] = 0x7f7f,
- [RT286_DAC_OUT2] = 0x7f7f,
- [RT286_SPDIF] = 0x0000,
- [RT286_ADC_IN1] = 0x4343,
- [RT286_ADC_IN2] = 0x4343,
- [RT286_MIC1] = 0x0000,
- [RT286_MIXER_IN] = 0x000b,
- [RT286_MIXER_OUT1] = 0x0002,
- [RT286_MIXER_OUT2] = 0x0000,
- [RT286_DMIC1] = 0x0000,
- [RT286_DMIC2] = 0x0000,
- [RT286_LINE1] = 0x0000,
- [RT286_BEEP] = 0x0000,
- [RT286_VENDOR_REGISTERS] = 0x0000,
- [RT286_SPK_OUT] = 0x8080,
- [RT286_HP_OUT] = 0x8080,
- [RT286_MIXER_IN1] = 0x0000,
- [RT286_MIXER_IN2] = 0x0000,
+};
+static int rt286_hw_read(void *context, unsigned int reg, unsigned int *value) +{
- struct i2c_client *client = context;
- struct i2c_msg xfer[2];
- int ret;
- unsigned int buf = 0x0;
- if (reg <= 0xff) { /*read cache*/
*value = rt286_reg_cache[reg];
Any reason particular reason to not use regmap caching? Also your cache is driver global which means different device instances will use the same cache, which will probably have very weired effects. Also you cache has less than 0xff entries, so the check is completely bogus.
return 0;- }
- reg = cpu_to_be32(reg);
Don't store values of different endianness in the same variable, all the static code checkers will complain about this. Use a __be32 type variable to hold the result of cpu_to_be32.
- /* Write register */
- xfer[0].addr = client->addr;
- xfer[0].flags = 0;
- xfer[0].len = 4;
- xfer[0].buf = (u8 *)®
- /* Read data */
- xfer[1].addr = client->addr;
- xfer[1].flags = I2C_M_RD;
- xfer[1].len = 4;
- xfer[1].buf = (u8 *)&buf;
- ret = i2c_transfer(client->adapter, xfer, 2);
- if (ret < 0)
return ret;- else if (ret != 2)
return -EIO;- *value = be32_to_cpu(buf);
- return 0;
+}
[...]
+static int rt286_update_bits(struct snd_soc_codec *codec, unsigned int vid,
unsigned int nid, unsigned int data,unsigned int mask, unsigned int value)+{
- struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec);
- unsigned int old, new, verb;
- int change, ret;
- verb = VERB_CMD((vid | 0x800), nid, data);
- regmap_read(rt286->regmap, verb, &old);
- new = (old & ~mask) | (value & mask);
- change = old != new;
- if (change) {
verb = VERB_CMD(vid, nid, new);ret = regmap_write(rt286->regmap, verb, 0);if (ret < 0) {dev_err(codec->dev,"Failed to write private reg: %d\n", ret);goto err;}- }
Can't this use regmap_update_bits()?
- return change;
+err:
- return ret;
+}
[...]
+static int rt286_index_update_bits(struct snd_soc_codec *codec,
- unsigned int wid, unsigned int index,
- unsigned int mask, unsigned int data)
+{
- unsigned int old, new;
- int change, ret;
- old = rt286_index_read(codec, wid, index);
- new = (old & ~mask) | (data & mask);
- change = old != new;
- if (change) {
ret = rt286_index_write(codec, wid, index, new);if (ret < 0) {dev_err(codec->dev,"Failed to write private reg: %d\n", ret);goto err;}- }
Same here.
- return change;
+err:
- return ret;
+}
[...]
+static int rt286_adc_values[] = {
const
- 0, 5,
+};
[...]
+static int rt286_set_bclk_ratio(struct snd_soc_dai *dai, unsigned int ratio) +{
- struct snd_soc_codec *codec = dai->codec;
- dev_dbg(codec->dev, "%s ratio=%d\n", __func__, ratio);
- if (50 == ratio)
The ratio is the number of bit-clock cycles per lr-clock cycle.
rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS,RT286_I2S_CTRL1, 0x1000, 0x1000);- else
rt286_index_update_bits(codec, RT286_VENDOR_REGISTERS,RT286_I2S_CTRL1, 0x1000, 0x0);- return 0;
+}
[...]
- if (rt286->i2c->irq) {
rt286_index_update_bits(codec,RT286_VENDOR_REGISTERS, RT286_IRQ_CTRL, 0x2, 0x2);ret = request_threaded_irq(rt286->i2c->irq, NULL, rt286_irq,IRQF_TRIGGER_HIGH | IRQF_ONESHOT, "rt286", rt286);
This IRQ is never freed.
if (ret != 0) {dev_err(codec->dev,"Failed to reguest IRQ: %d\n", ret);return ret;}- }
- return 0;
+}
+#define RT286_STEREO_RATES (SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000) +#define RT286_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE | \
SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S8)+struct snd_soc_dai_ops rt286_aif_dai_ops = {
const
- .hw_params = rt286_hw_params,
- .set_fmt = rt286_set_dai_fmt,
- .set_sysclk = rt286_set_dai_sysclk,
- .set_bclk_ratio = rt286_set_bclk_ratio,
+};
+struct snd_soc_dai_driver rt286_dai[] = {
- {
.name = "rt286-aif1",.id = RT286_AIF1,.playback = {.stream_name = "AIF1 Playback",.channels_min = 1,.channels_max = 2,.rates = RT286_STEREO_RATES,.formats = RT286_FORMATS,},.capture = {.stream_name = "AIF1 Capture",.channels_min = 1,.channels_max = 2,.rates = RT286_STEREO_RATES,.formats = RT286_FORMATS,},.ops = &rt286_aif_dai_ops,.symmetric_rates = 1,
Indention is a bit strange here.
},+};
[...]
+static const struct i2c_device_id rt286_i2c_id[] = {
- {"rt286", 0},
- {}
+}; +MODULE_DEVICE_TABLE(i2c, rt286_i2c_id);
+static struct acpi_device_id rt286_acpi_match[] = {
const
- { "INT343A", 0 },
- {},
+}; +MODULE_DEVICE_TABLE(acpi, rt286_acpi_match);
+static int rt286_i2c_probe(struct i2c_client *i2c,
const struct i2c_device_id *id)+{
- struct rt286_platform_data *pdata = dev_get_platdata(&i2c->dev);
- struct rt286_priv *rt286;
- struct device *dev = &i2c->dev;
- int ret;
- rt286 = devm_kzalloc(&i2c->dev,
sizeof(struct rt286_priv),
sizeof(*rt286) is prefered kernel style
GFP_KERNEL);- if (NULL == rt286)
return -ENOMEM;- rt286->regmap = devm_regmap_init(dev, NULL, i2c, &rt286_regmap);
- if (IS_ERR(rt286->regmap)) {
ret = PTR_ERR(rt286->regmap);dev_err(&i2c->dev, "Failed to allocate register map: %d\n",ret);return ret;- }
- rt286->i2c = i2c;
- i2c_set_clientdata(i2c, rt286);
- if (pdata)
rt286->pdata = *pdata;- ret = devm_snd_soc_register_codec(&i2c->dev, &soc_codec_dev_rt286,
rt286_dai, ARRAY_SIZE(rt286_dai));
There is no such thing as devm_snd_soc_register_codec().
- return ret;
+}
-----Original Message----- From: Lars-Peter Clausen [mailto:lars@metafoo.de] Sent: Thursday, March 13, 2014 5:16 AM To: Bard Liao Cc: broonie@kernel.org; lgirdwood@gmail.com; Oder Chiou; alsa-devel@alsa-project.org; Gustaw Lewandowski; Flove Subject: Re: [alsa-devel] [PATCH v5] ASoC: add RT286 CODEC driver
On 03/11/2014 08:11 AM, bardliao@realtek.com wrote: [...]
+static unsigned int rt286_reg_cache[] = {
- [RT286_AUDIO_FUNCTION_GROUP] = 0x0000,
- [RT286_DAC_OUT1] = 0x7f7f,
- [RT286_DAC_OUT2] = 0x7f7f,
- [RT286_SPDIF] = 0x0000,
- [RT286_ADC_IN1] = 0x4343,
- [RT286_ADC_IN2] = 0x4343,
- [RT286_MIC1] = 0x0000,
- [RT286_MIXER_IN] = 0x000b,
- [RT286_MIXER_OUT1] = 0x0002,
- [RT286_MIXER_OUT2] = 0x0000,
- [RT286_DMIC1] = 0x0000,
- [RT286_DMIC2] = 0x0000,
- [RT286_LINE1] = 0x0000,
- [RT286_BEEP] = 0x0000,
- [RT286_VENDOR_REGISTERS] = 0x0000,
- [RT286_SPK_OUT] = 0x8080,
- [RT286_HP_OUT] = 0x8080,
- [RT286_MIXER_IN1] = 0x0000,
- [RT286_MIXER_IN2] = 0x0000,
+};
+static int rt286_hw_read(void *context, unsigned int reg, unsigned +int *value) {
- struct i2c_client *client = context;
- struct i2c_msg xfer[2];
- int ret;
- unsigned int buf = 0x0;
- if (reg <= 0xff) { /*read cache*/
*value = rt286_reg_cache[reg];Any reason particular reason to not use regmap caching? Also your cache is driver global which means different device instances will use the same cache, which will probably have very weired effects. Also you cache has less than 0xff entries, so the check is completely bogus.
Because rt286 uses different registers for read and write the same bits. So, I can't read the real value from cache. The cache I am using is for dummy registers actually. These dummy registers are mainly used for dapm to get the route information. We don't touch the codec when read/write these dummy registers. I will try to put the cache into rt286_priv. And will change if (reg <= 0xff) to if (reg <= RT286_MIXER_IN2).
- /* Write register */
- xfer[0].addr = client->addr;
- xfer[0].flags = 0;
- xfer[0].len = 4;
- xfer[0].buf = (u8 *)®
- /* Read data */
- xfer[1].addr = client->addr;
- xfer[1].flags = I2C_M_RD;
- xfer[1].len = 4;
- xfer[1].buf = (u8 *)&buf;
- ret = i2c_transfer(client->adapter, xfer, 2);
- if (ret < 0)
return ret;- else if (ret != 2)
return -EIO;- *value = be32_to_cpu(buf);
- return 0;
+}
[...]
+static int rt286_update_bits(struct snd_soc_codec *codec, unsigned int vid,
unsigned int nid, unsigned int data,unsigned int mask, unsigned int value) {- struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec);
- unsigned int old, new, verb;
- int change, ret;
- verb = VERB_CMD((vid | 0x800), nid, data);
- regmap_read(rt286->regmap, verb, &old);
- new = (old & ~mask) | (value & mask);
- change = old != new;
- if (change) {
verb = VERB_CMD(vid, nid, new);ret = regmap_write(rt286->regmap, verb, 0);if (ret < 0) {dev_err(codec->dev,"Failed to write private reg: %d\n", ret);goto err;}- }
Can't this use regmap_update_bits()?
rt286 use different data length for read/write protocol. Also it uses different registers for read/write the same bit.
verb = VERB_CMD((vid | 0x800), nid, data); regmap_read(rt286->regmap, verb, &old); ... verb = VERB_CMD(vid, nid, new); ret = regmap_write(rt286->regmap, verb, 0);
I use different reg(verb) for regmap_read and regmap_write. And set regmap_write's val variable to 0. I think regmap_update_bits() will do things like regmap_read(rt286->regmap, verb, &old); regmap_write(rt286->regmap, verb, new); with the same verb value.
- return change;
+err:
- return ret;
+}
[...]
+static int rt286_index_update_bits(struct snd_soc_codec *codec,
- unsigned int wid, unsigned int index,
- unsigned int mask, unsigned int data) {
- unsigned int old, new;
- int change, ret;
- old = rt286_index_read(codec, wid, index);
- new = (old & ~mask) | (data & mask);
- change = old != new;
- if (change) {
ret = rt286_index_write(codec, wid, index, new);if (ret < 0) {dev_err(codec->dev,"Failed to write private reg: %d\n", ret);goto err;}- }
Same here.
Same reason as above.
- 0, 5,
+};
[...]
+static int rt286_set_bclk_ratio(struct snd_soc_dai *dai, unsigned int +ratio) {
- struct snd_soc_codec *codec = dai->codec;
- dev_dbg(codec->dev, "%s ratio=%d\n", __func__, ratio);
- if (50 == ratio)
The ratio is the number of bit-clock cycles per lr-clock cycle.
That is exactly the information we need to know.
GFP_KERNEL);- if (NULL == rt286)
return -ENOMEM;- rt286->regmap = devm_regmap_init(dev, NULL, i2c, &rt286_regmap);
- if (IS_ERR(rt286->regmap)) {
ret = PTR_ERR(rt286->regmap);dev_err(&i2c->dev, "Failed to allocate register map: %d\n",ret);return ret;- }
- rt286->i2c = i2c;
- i2c_set_clientdata(i2c, rt286);
- if (pdata)
rt286->pdata = *pdata;- ret = devm_snd_soc_register_codec(&i2c->dev, &soc_codec_dev_rt286,
rt286_dai, ARRAY_SIZE(rt286_dai));There is no such thing as devm_snd_soc_register_codec().
That is Mark's suggestion. I suppose devm_snd_soc_register_codec() will be upstreaming soon. Should I use snd_soc_register_codec() in this patch?
- return ret;
+}
------Please consider the environment before printing this e-mail.
On 03/13/2014 06:29 AM, Bard Liao wrote:
[...]
+static int rt286_update_bits(struct snd_soc_codec *codec, unsigned int vid,
unsigned int nid, unsigned int data,unsigned int mask, unsigned int value) {- struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec);
- unsigned int old, new, verb;
- int change, ret;
- verb = VERB_CMD((vid | 0x800), nid, data);
- regmap_read(rt286->regmap, verb, &old);
- new = (old & ~mask) | (value & mask);
- change = old != new;
- if (change) {
verb = VERB_CMD(vid, nid, new);ret = regmap_write(rt286->regmap, verb, 0);if (ret < 0) {dev_err(codec->dev,"Failed to write private reg: %d\n", ret);goto err;}- }
Can't this use regmap_update_bits()?
rt286 use different data length for read/write protocol. Also it uses different registers for read/write the same bit.
verb = VERB_CMD((vid | 0x800), nid, data); regmap_read(rt286->regmap, verb, &old); ... verb = VERB_CMD(vid, nid, new); ret = regmap_write(rt286->regmap, verb, 0);
You need to differentiate between logical and physical addresses. If your device uses different physical addresses for read and write then your read and write functions should do the proper translation from the logical address to the physical address. Looking at include/sound/hda_verbs.h it seems that the GET verbs are always the same as the SET verbs but additionally set bit 11. So bit 11 is your read bit that always needs to be set when reading a register. This is nothing special to the rt286, in fact it is so common that regmap as support for this in the core. See the read_flag_mask for the regmap_config struct.
I use different reg(verb) for regmap_read and regmap_write. And set regmap_write's val variable to 0.
So you changed the regmap semantics and do pass the value of the register write via address and set value always to zero. In that it would probably been better to not use regmap at all. But as I said, there doesn't seem to be anything special about the device, you just need to implement the read and write callbacks correctly, then it is no problem to use regmap_update_bits and also regmap level caching.
I think regmap_update_bits() will do things like regmap_read(rt286->regmap, verb, &old); regmap_write(rt286->regmap, verb, new); with the same verb value.
- return change;
+err:
- return ret;
+}
[...]
+static int rt286_index_update_bits(struct snd_soc_codec *codec,
- unsigned int wid, unsigned int index,
- unsigned int mask, unsigned int data) {
- unsigned int old, new;
- int change, ret;
- old = rt286_index_read(codec, wid, index);
- new = (old & ~mask) | (data & mask);
- change = old != new;
- if (change) {
ret = rt286_index_write(codec, wid, index, new);if (ret < 0) {dev_err(codec->dev,"Failed to write private reg: %d\n", ret);goto err;}- }
Same here.
Same reason as above.
rt286_index_read and rt286_index_write seem to implement a paging mechanism. regmap has native support for paging, see regmap_range_cfg. If you can't use regmap for paging implement the paging mechanism in your read/write callbacks.
- 0, 5,
+};
[...]
+static int rt286_set_bclk_ratio(struct snd_soc_dai *dai, unsigned int +ratio) {
- struct snd_soc_codec *codec = dai->codec;
- dev_dbg(codec->dev, "%s ratio=%d\n", __func__, ratio);
- if (50 == ratio)
The ratio is the number of bit-clock cycles per lr-clock cycle.
That is exactly the information we need to know.
GFP_KERNEL);- if (NULL == rt286)
return -ENOMEM;- rt286->regmap = devm_regmap_init(dev, NULL, i2c, &rt286_regmap);
- if (IS_ERR(rt286->regmap)) {
ret = PTR_ERR(rt286->regmap);dev_err(&i2c->dev, "Failed to allocate register map: %d\n",ret);return ret;- }
- rt286->i2c = i2c;
- i2c_set_clientdata(i2c, rt286);
- if (pdata)
rt286->pdata = *pdata;- ret = devm_snd_soc_register_codec(&i2c->dev, &soc_codec_dev_rt286,
rt286_dai, ARRAY_SIZE(rt286_dai));There is no such thing as devm_snd_soc_register_codec().
That is Mark's suggestion. I suppose devm_snd_soc_register_codec() will be upstreaming soon. Should I use snd_soc_register_codec() in this patch?
Yes, otherwise the driver won't compile.
At Thu, 13 Mar 2014 09:35:40 +0100, Lars-Peter Clausen wrote:
On 03/13/2014 06:29 AM, Bard Liao wrote:
[...]
+static int rt286_update_bits(struct snd_soc_codec *codec, unsigned int vid,
unsigned int nid, unsigned int data,unsigned int mask, unsigned int value) {- struct rt286_priv *rt286 = snd_soc_codec_get_drvdata(codec);
- unsigned int old, new, verb;
- int change, ret;
- verb = VERB_CMD((vid | 0x800), nid, data);
- regmap_read(rt286->regmap, verb, &old);
- new = (old & ~mask) | (value & mask);
- change = old != new;
- if (change) {
verb = VERB_CMD(vid, nid, new);ret = regmap_write(rt286->regmap, verb, 0);if (ret < 0) {dev_err(codec->dev,"Failed to write private reg: %d\n", ret);goto err;}- }
Can't this use regmap_update_bits()?
rt286 use different data length for read/write protocol. Also it uses different registers for read/write the same bit.
verb = VERB_CMD((vid | 0x800), nid, data); regmap_read(rt286->regmap, verb, &old); ... verb = VERB_CMD(vid, nid, new); ret = regmap_write(rt286->regmap, verb, 0);
You need to differentiate between logical and physical addresses. If your device uses different physical addresses for read and write then your read and write functions should do the proper translation from the logical address to the physical address. Looking at include/sound/hda_verbs.h it seems that the GET verbs are always the same as the SET verbs but additionally set bit 11. So bit 11 is your read bit that always needs to be set when reading a register. This is nothing special to the rt286, in fact it is so common that regmap as support for this in the core. See the read_flag_mask for the regmap_config struct.
Note that get and set aren't always symmetrical for HD-audio. You can get up to 32bit, but set only up to 8 bit, thus some verbs are split to multiple different set verbs. Also, some verbs expect different values for get and set. And, yet more tricky part is the amplifier verbs. These aren't suitable with regmap caching, unfortunately.
Takashi
On Thu, Mar 13, 2014 at 09:52:14AM +0100, Takashi Iwai wrote:
different values for get and set. And, yet more tricky part is the amplifier verbs. These aren't suitable with regmap caching, unfortunately.
We don't really *need* the cache, it just makes it easier to do resume and gives a bit of a performance boost.
At Thu, 13 Mar 2014 19:29:02 +0000, Mark Brown wrote:
On Thu, Mar 13, 2014 at 09:52:14AM +0100, Takashi Iwai wrote:
different values for get and set. And, yet more tricky part is the amplifier verbs. These aren't suitable with regmap caching, unfortunately.
We don't really *need* the cache, it just makes it easier to do resume and gives a bit of a performance boost.
Well, the caching isn't just a bit. Without caching, you'd have to whip the sound hardware powered up/down at each time querying the current mixer value.
My point is only that the design of HD-audio is so plain ugly :)
Takashi
On Thu, Mar 13, 2014 at 09:04:49PM +0100, Takashi Iwai wrote:
Mark Brown wrote:
We don't really *need* the cache, it just makes it easier to do resume and gives a bit of a performance boost.
Well, the caching isn't just a bit. Without caching, you'd have to whip the sound hardware powered up/down at each time querying the current mixer value.
Realistically most hardware can't actually do that - there's a couple of the idle_bias_off devices that have built in LDOs which can but it's relatively unusual to be able to remove enough power to loose register I/O (and in any case you wind up needing to cache the values per control or something in order to do system suspend).
-----Original Message----- From: Mark Brown [mailto:broonie@kernel.org] Sent: Friday, March 14, 2014 4:43 AM To: Takashi Iwai Cc: Lars-Peter Clausen; Bard Liao; Oder Chiou; alsa-devel@alsa-project.org; lgirdwood@gmail.com; Gustaw Lewandowski; Flove Subject: Re: [alsa-devel] [PATCH v5] ASoC: add RT286 CODEC driver
On Thu, Mar 13, 2014 at 09:04:49PM +0100, Takashi Iwai wrote:
Mark Brown wrote:
We don't really *need* the cache, it just makes it easier to do resume and gives a bit of a performance boost.
Well, the caching isn't just a bit. Without caching, you'd have to whip the sound hardware powered up/down at each time querying the current mixer value.
Realistically most hardware can't actually do that - there's a couple of the idle_bias_off devices that have built in LDOs which can but it's relatively unusual to be able to remove enough power to loose register I/O (and in any case you wind up needing to cache the values per control or something in order to do system suspend).
Mark,
What's your suggestion of the I/O part of rt286 codec driver? Can I keep using regmap without using its cache? Or it is better not using regmap in this driver?
Thanks.
------Please consider the environment before printing this e-mail.
On Fri, Mar 14, 2014 at 09:38:20AM +0000, Bard Liao wrote:
What's your suggestion of the I/O part of rt286 codec driver? Can I keep using regmap without using its cache? Or it is better not using regmap in this driver?
I think we need to understand what the code is actually trying to do - I'm intending to go through the driver today or before the weekend but from the quick look at the I/O code I'm just really confused about what is supposed to be happening. I'll try to follow up before Monday.
On Tue, Mar 11, 2014 at 03:11:36PM +0800, bardliao@realtek.com wrote:
From: Bard Liao bardliao@realtek.com
This patch adds the ALC286 codec driver.
ALC286 is a dual mode codec, which can run as HD-A or I2S mode. It is controlled by HD-A verb commands via I2C protocol.
Some or all of this documentation needs to end up in the code, we need to be able to understand and maintain the code going forwards and while the commit message is going to be kept it's still useful if the code can be followed. Right now that's extremely hard.
The following is the I/O difference between ALC286 and general I2S codecs.
- A HD-A verb command contains three parts, NID, VID, and PID. And an I2S command contains only two parts: address and data.
It'd probably help to explain waht these are.
- Not only the register address is written, but the read command also includes the entire write command.
- rt286 uses different registers for read and write the same bits.
As a result, standard regmap is difficult to be used on ALC286. We don't request a standard I/O by snd_soc_codec_set_cache_io anymore. Now we have ,reg_write and .reg_read functions for ALC286's I/O. And we don't use cache due to item 3 above. Some dummy registers (address <= 0xff) are defined for dapm routing. Thhe dummy registers are cache only.
Don't use dummy registers, DAPM already has virtual controls of various kinds - if you need more let's extend them. Storing data in virtual registers just makes things confusing and fragile. Some older CODEC drivers did it and they're harder to work with now than they should be.
Due to item 2 above, HD-A verb commands are put into the address part of regmap. When we issue HD-A verb write commands, the data part of regmap is zero.
I'm having a really hard time understanding how this follows. We do have some other devices that do things like have multi-level register addresses with registers collected in pages. By analogy here what I'd expect to see is something which combines the various pieces of addressing information into a bitfields within a single number that can be used as a register address.
Or perhaps this just isn't anything like a register map at all? Whatever is going on something that ignores the value part of the regmap interfaces doesn't seem like it is a very good fit.
-----Original Message----- From: Mark Brown [mailto:broonie@kernel.org] Sent: Saturday, March 15, 2014 3:13 AM To: Bard Liao Cc: lgirdwood@gmail.com; alsa-devel@alsa-project.org; Flove; Oder Chiou; Gustaw Lewandowski Subject: Re: [PATCH v5] ASoC: add RT286 CODEC driver
On Tue, Mar 11, 2014 at 03:11:36PM +0800, bardliao@realtek.com wrote:
From: Bard Liao bardliao@realtek.com
This patch adds the ALC286 codec driver.
ALC286 is a dual mode codec, which can run as HD-A or I2S mode. It is controlled by HD-A verb commands via I2C protocol.
Some or all of this documentation needs to end up in the code, we need to be able to understand and maintain the code going forwards and while the commit message is going to be kept it's still useful if the code can be followed. Right now that's extremely hard.
I will put these description in the code.
The following is the I/O difference between ALC286 and general I2S codecs.
- A HD-A verb command contains three parts, NID, VID, and PID. And an I2S command contains only two parts: address and data.
It'd probably help to explain waht these are.
RT286 use verb commands to control the codec. A verb command contains three parts, NID, VID, and PID. For example, if I want to unmute headphone, I should set: VID = 3'h (Set Amplifier Gain) NID = 22'h (headphone) PID = b000'h (Set left, right output unmute)
Below is the description in rt286 datasheet. In SOC mode CODEC can ONLY be access via I2C, and CODEC works as slave mode and slave ID is 38'h. therefore HD-A verb needs to be translated via I2C protocol, no matter Read or Write HD-A command, 32 bits(8*4) command code must be issued by I2C master to compose 32 bits HD-A verb, CODEC will decode the verb, if write verb(ex: HD-A verb: 2h) was decoded, the target NID will be set to target setting, if Read verb(ex: HD-A verb: Ah) was decoded, CODEC will response the response 32 bits(8*4) response via normal I2C protocol, detail protocol please refer below.
I draw a picture below to show the I2C protocol of rt286.
I2C Write: |1| 7 | 1 |1| 4 | 4 |1| 4 | 4 |1| 8 |1| 8 |1|1 |S|Device Address|W|A|Reserved|NID[7:4]|A|NID[3:0]|VID[11:8]|A|VID[7:0]|A|Payload[7:0]|A|P
I2C Read: |1| 7 |1 |1| 4 | 4 |1| 4 | 4 |1| 8 |1| 8 |1|1| |S|Device Address|W|A|Reserved|NID[7:4]|A|NID[3:0]|VID[11:8]|A|VID[7:0]|A|Payload[7:0]|A|S|-> 8 |1| 8 |1| 8 |1| 8 |1 | 8 |1 |1 ->Device Address|R|RD_DATA[31:24]|A|RD_DATA[23:16]|A|RD_DATA[15:8]|A|RD_DATA7:0]|NA|P
- Not only the register address is written, but the read command also includes the entire write command.
- rt286 uses different registers for read and write the same bits.
As a result, standard regmap is difficult to be used on ALC286. We don't request a standard I/O by snd_soc_codec_set_cache_io anymore. Now we have ,reg_write and .reg_read functions for ALC286's I/O. And we don't use cache due to item 3 above. Some dummy registers (address <= 0xff) are defined for dapm routing. Thhe dummy registers are cache only.
Don't use dummy registers, DAPM already has virtual controls of various kinds
- if you need more let's extend them. Storing data in virtual registers just
makes things confusing and fragile. Some older CODEC drivers did it and they're harder to work with now than they should be.
Use SOC_DAPM_SINGLE_VIRT?
Due to item 2 above, HD-A verb commands are put into the address part of
regmap.
When we issue HD-A verb write commands, the data part of regmap is zero.
I'm having a really hard time understanding how this follows. We do have some other devices that do things like have multi-level register addresses with registers collected in pages. By analogy here what I'd expect to see is something which combines the various pieces of addressing information into a bitfields within a single number that can be used as a register address.
Or perhaps this just isn't anything like a register map at all? Whatever is going on something that ignores the value part of the regmap interfaces doesn't seem like it is a very good fit.
I draw a general I2C protocol below. I2C Write: S|Device Address|W|A|Register Address|A|Data Byte High|A|Data Byte Low|A|P I2C Read: S|Device Address|W|A|Register Address|A|S|Device Address|R|A|Data Byte High|A|Data Byte Low|A|P
Usually, we call the data before " S|Device Address|R|" register address. But in rt286's i2c read protocol, we have an entire write command before " S|Device Address|R|".
If I combine NID and VID to be used as a register address, and let PID as register value, it will be very difficult to define(or use) a _update_btis function. Because I need to put all NID, VID and PID in the register address area when I issue a I2C read command. So, I put all NID, VID and PID in the register address area no matter read or write command is issued. As a result, we don't use the register value area when we use regmap_write. That's why the register value area is always nothing(zero) when we call regmap_write.
------Please consider the environment before printing this e-mail.
On Tue, Mar 18, 2014 at 12:41:41PM +0000, Bard Liao wrote:
Please fix your mailer to word wrap within paragraphs, this will make your mail more legible.
A verb command contains three parts, NID, VID, and PID. For example, if I want to unmute headphone, I should set: VID = 3'h (Set Amplifier Gain) NID = 22'h (headphone) PID = b000'h (Set left, right output unmute)
So VID+NID is an address and PID is a value?
- if you need more let's extend them. Storing data in virtual registers just
makes things confusing and fragile. Some older CODEC drivers did it and they're harder to work with now than they should be.
Use SOC_DAPM_SINGLE_VIRT?
Yes, that'd be a much better fit.
If I combine NID and VID to be used as a register address, and let PID as register value, it will be very difficult to define(or use) a _update_btis function. Because I need to put all NID, VID and PID in the register address area when I issue a I2C read command.
I don't see how this follows at all - all update_bits() is doing is a read/modify/write so if you can implement write and read then it comes along for free. It sounds like you need to do a cache read to get the current PID to do a read but it's not at all obvious what that has to do with update_bits() or how putting the value into the address avoids having to know the current value to do a read?
I think what you're saying above is that your read needs to have a cache read in it to function if you use normal register values?
-----Original Message----- From: Mark Brown [mailto:broonie@kernel.org] Sent: Tuesday, March 18, 2014 9:02 PM To: Bard Liao Cc: lgirdwood@gmail.com; alsa-devel@alsa-project.org; Flove; Oder Chiou; Gustaw Lewandowski Subject: Re: [PATCH v5] ASoC: add RT286 CODEC driver
On Tue, Mar 18, 2014 at 12:41:41PM +0000, Bard Liao wrote:
Please fix your mailer to word wrap within paragraphs, this will make your mail more legible.
Now I set 80 characters to wrap the text. Hope it can work.
A verb command contains three parts, NID, VID, and PID. For example, if I want to unmute headphone, I should set: VID = 3'h (Set Amplifier Gain) NID = 22'h (headphone) PID = b000'h (Set left, right output unmute)
So VID+NID is an address and PID is a value?
For I2C write, yes. But for I2C read, I think PID is also a part of address. Because PID is meaningful in the I2C read protocol. For example, if we need to get the mute/unmute status of headphone, we need to set: VID = b'h (Get Amplifier Gain) NID = 22'h (Headhoone) PID = a000'h (Left output amplifier gain is requested) And we can get response from rt286.
I am trying to implement my reg_write and reg_read to: reg_write: address: VID+NID, value: PID reg_read: address: VID+NID+PID, value: the responding data from rt286.
Thanks.
On Fri, Mar 21, 2014 at 05:57:49AM +0000, Bard Liao wrote:
Please fix your mailer to word wrap within paragraphs, this will make your mail more legible.
Now I set 80 characters to wrap the text. Hope it can work.
Doesn't seem to have taken I'm afraid :(
So VID+NID is an address and PID is a value?
For I2C write, yes. But for I2C read, I think PID is also a part of address. Because PID is meaningful in the I2C read protocol. For example, if we need to get the mute/unmute status of headphone, we need to set: VID = b'h (Get Amplifier Gain) NID = 22'h (Headhoone) PID = a000'h (Left output amplifier gain is requested) And we can get response from rt286.
I am trying to implement my reg_write and reg_read to: reg_write: address: VID+NID, value: PID reg_read: address: VID+NID+PID, value: the responding data from rt286.
Right, that's why I said you'll need to read the cache as part of your read function. Unless the PID there is not the last value that was set in which case it probably isn't actually a register value...
participants (5)
-
Bard Liao -
bardliao＠realtek.com
-
Lars-Peter Clausen -
Mark Brown -
Takashi Iwai